This document provides information about PN16 two/three-way valves including their models, Kvs values, stroke lengths, applications, manufacturing characteristics, technical characteristics, installation instructions, actuators, accessories, and application schemes. It includes tables with maximum differential close-off pressures and regulation differential pressures.
This document provides information about PN16 two/three-way valves including their models, Kvs values, stroke lengths, applications, manufacturing characteristics, technical characteristics, installation instructions, actuators, accessories, and application schemes. It includes tables with maximum differential close-off pressures and regulation differential pressures.
This document provides information about PN16 two/three-way valves including their models, Kvs values, stroke lengths, applications, manufacturing characteristics, technical characteristics, installation instructions, actuators, accessories, and application schemes. It includes tables with maximum differential close-off pressures and regulation differential pressures.
This document provides information about PN16 two/three-way valves including their models, Kvs values, stroke lengths, applications, manufacturing characteristics, technical characteristics, installation instructions, actuators, accessories, and application schemes. It includes tables with maximum differential close-off pressures and regulation differential pressures.
VMB VSB Two-way VSB and three-way VMB valves can be used either for con- trol or fluid detection in air-conditioning, thermoventilation and heat- ing plants, both environmental and industrial, and in machines for product thermal process. Three-way valves should be used only as mixing valves; angle way should never be used for control purposes.
MANUFACTURING CHARACTERISTICS
The valve body is made of G25 cast iron. The plug is in brass with Con- toured-type profile on direct way and V-port on angle way. The stem is in CrNi steel with threaded M8 end and female threaded connections. The stem packing is constituted by a EPDM O-ring with graphited teflon scraper rings. NOTE: The valves are also available in the stainless steel plug version (profile and Kvs are the same of the brass plug). For further sales in- formation, please contact our Sales Support. INSTALLATION
TECHNICAL CHARACTERISTICS Before valves are mounted, make sure that pipes are clean, free from welding slags, that are perfectly lined up with valve body and not subjected to vibrations. Constructions: PN16 The valve can be mounted in any position except upside-down (for Control characteristics: direct way equal-percentage MVH actuators see Fig. 3). angle way linear (VMB) While assembling, respect the flow directions indicated by the Leakage*: direct way 0...0,03% of Kvs letters located on the valve body (see Fig. 1 and 2) and the appli- angle way 0...2% of Kvs (VMB) cation schemes. Connections: female threaded Stroke: 16,5mm (max 18,5) Allowed fluids: - water: max. temperature 150°C min. temperature -10 °C (in case of ice on stem and gasket, use the stem-heater, see actuators data sheets; is not applicable to V.B DN15 valves) glycol added max 50% - saturated steam: max. temperature 150 °C max. pressure 250kPa (absolute value) Weight: see dimensions
* Leakage is measured according to the EN1349 standard.
ATTENTION: If V.B valves are assembled with MVB+spacer (MVBHT)
the max. operating temperature is 140°C, while without spacer is 120°C. For other actuators the max. operating temperature is 150 °C.
VSB and VMB are actuated by CONTROLLI MVB, MVH, MVH56EA/C, AG52 Valve linkage kit with MVE MVE electrical actuators. AG62 Valve linkage kit with MVH AG63 Valve linkage kit with MVE..S GVB3 Insulation shell for DN 3/4“ valves for V.B3 MOUNTING POSITIONS GVB4 Insulation shell for DN 1“ valves for V.B4 GVB5 Insulation shell for DN 1 ¼” for V.B5 GVB6 Insulation shell for DN 1 ½” for V.B6 GVB8 Insulation shell for DN 2” for V.B8 Fig. 3 GVB8A Insulation shell for DN 2” for V.B8A
CAST IRON FITTINGS 3 PIECES
THREAD FITTING SEAL CODE A B CODE
G3/4” F G3/4” M 89948-02 89949-02
YES NO G1” F G1” M 89948-03 89949-03 G1 ¼” F G1 ¼” M 89948-04 89949-04 OPERATING G1 ½” F G1 ½” M 89948-05 89949-05 G2” F G2” M 89948-06 89949-06 With the stem extended, the direct way is closed. With the stem retracted, the direct way is open.
APPLICATION SCHEMES
VSB VALVES VMB VALVES
a) Variable flow control when used c) Variable flow mixing when used
A AB AB A USER B USER
b) Constant flow when used in injection circuits d) Constant flow mixing when used in injection or tapping circuits
* with MVH.A in emergency valve closed, with MVH.C in emergency valve open.
2nd Issue rev. i 07/2020 DBL008e Page 2
MAX REGULATION DIFFERENTIAL PRESSURE [kPa]
The max regulation differential pressure, it means the pressure which can be used during the stroke, is conditioned by wear between seat and plug and by the performance guaranteed by the actuator for the evaluated valve. So we recommend not to overcome the differential pressure whose value corresponds to the minimum between 200kPa (maximum admitted value not to cause wear) and the one shown in the previous table (max close-off differential pressure).
Note: The max operating pressures at different temperatures for various PN classes must correspond to the following standards: UNI 1092-02 and UNI 12516-1.
