Nerolac Perma Construction Chemicals
Nerolac Perma Construction Chemicals
Nerolac Perma Construction Chemicals
GHAR KO
JUG-JUG JIYO
AL_2023_02 FEB_KANSAI NEROLAC PAINTS LTD_CORP_11910618_ 7 (W) X 4.75 (H)_INCH_NEROLAC PERMA POCKET GUIDE
About Nerolac Perma Range
1. Surface preparation
Up to 80C of surface
UV resistant
temperature reduction 1 2 3
*T&C apply
1. Recommended Waterproofing Applications Coverage
a) For terrace (horizontal surfaces) For 8 years: Exterior walls: 25-26 sft/L
Terrace: 9-10 sft/L
1 2
1 2 1 2
Apply one self-priming coat of Allow it to dry for a Apply one self-priming coat Allow it to dry for at least 3-4 h.
Nerolac Perma Damp Protect minimum of 4 h followed of Nerolac Perma Damp Apply two coats as per forced
Exterior (10% by volume/100 ml by one undiluted coat of Protect Exterior (diluted with coverage
water to 1 ltr of Nerolac Perma Damp Nerolac Perma Damp water in 3:1 ratio by volume)
Protect Exterior) on the surface with Protect Exterior
the help of a brush or roller
3
3
Make sure the product is
applied on entire roof
including paraper walls
to form a blanket
Top coat this treatment with
two coats of any Nerolac Paints
Exterior Emulsion Paint as per
the recommended application
procedure
Packaging
Nerolac Perma Damp Protect Exterior is available in 1 ltr, 4 ltr,
10 ltr and 20 ltr packs
DAMP PROTECT INTERIOR
Mixing
JAB DEEWARON SE Dilute Nerolac Perma Damp Protect Interior 50% by volume with water
SEELAN HATEGI, and apply it in two coats
Coverage
JAB DEEWARON SE 15 +/- 3 sft/L in two coats
SEELAN HATEGI, (Coverage may vary depending on quality of substrates, undulations in
substrates and skill of applicator)
TAB KHOOBSURATI
Application Method
LAMBI CHALEGI
1. Surface Preparation
• Remove all loose and deleterious material from the wall with the help of
wire brush, putty blade or other suitable equipment. Dampen or moist the
surface with water to foster smooth and easy application of Nerolac Perma
Product Benefits Waterproof Cement Putty
• Mix Nerolac Perma Waterproof Premium Putty with 35-40% clean water to
make a smooth and homogeneous easy-to-apply paste
Resists dampness Excellent levelling
and efflorescence and easy sanding 2. Recommended Application
• It is recommended to use Nerolac Speed X Putty mixer for uniform
and lump-free mixing
• Apply first coat of Nerolac Perma Waterproof Premium Putty on
Less dusting wet/moistened surface from bottom to top in upward direction
while sanding High coverage
with putty blade or suitable equipment. Allow the surface to dry
for 4-6 h depending on climatic conditions
• Sand the surface with emery paper if needed to level the surface
• Apply second coat of Nerolac Perma Waterproof Cement Putty.
Wall primer Wet sponge the final coat. Allow it to dry thoroughly overnight
PRIMER
can be avoided before applying paint application
Packaging
Nerolac Perma Waterproof Premium Putty is available in 20 kg and 40 kg packs
*T&C apply
SUPER 2K
SUPER 2K
Mixing
1
Coverage
Application Areas 6-7 sq.ft/kg in 2 coats
• Walls • Concrete roof and podium slabs • Basement retaining wall Packaging
• Toilet & Bathroom sunk • Concrete water tank
Nerolac Perma Super 2K is available in 3 kg and 15 kg packs
CRACK FILLER
CRACK FILLER
Application Method
1 2
JO BADHAYE
AAPKE DEEWARON
KI UMAR Surface should be free from Hairline cracks must be widened up to 1mm
dust, oil, grease and loose width minimum and then filled. Widen the
particles cracks to form a ‘V’ groove and prime the
surface with suitable primer
3 4
Product Benefits
Fill one coat of Nerolac Perma Press the paste firmly into the crack with a
Strong Adhesion
Water Resistant Crack Filler spatula or putty knife and level with the
& Flexible
surface. Allow it to dry for overnight
Coverage
Application Areas 25 – 30 RMT/Kg in 5 mm width x 5 mm depth of crack
WATERPROOF POLYMER • As Repair Mortar & Concrete - Mix 10% of Nerolac Perma Waterproof
Polymer by weight of cement
Coverage
• Waterproof coating: 21-25 sft/L • Bonding Agent & Bonding tile
on tile: 45-50 sft/L per coat • Repair Mortar: 5 ltr per 50 kg of cement bag
Application Method
1. Surface preparation
JO BADHAYE AAPKE
CHATTH KI UMAR 1
Surface to be treated must be
thoroughly cleaned and all loose
material must be removed
2. Recommended Applications
Product Benefits
Strong 1For Waterproofing - 2 As Bond Coat - Apply only
Prevents Apply as per single coat on surface to be
bonding Durable Economical
corrosion
to concrete repairs waterproofing suggested mixing repaired as per suggested
and cracks
and plaster in 2 coats, a gap of mixing. For good adhesion,
1-2 h to be kept in apply repair mortar / concrete
Application Areas between each coat when the bond coat is tacky
CEMENT+
Application Areas
Slab, Concrete & Plaster
Application Method
1 2
JO BADAI APKE
GHAR KI UMAR
Packaging
Enhances life
Nerolac Perma Cement+ is available in 200 ml, 1 ltr, 5 ltr and 20 ltr packs
NO DAMP +
10 YEARS WARRANTY
12 YEARS WARRANTY
WALLS Coat 1 2
Coverage
Up to 140C of surface Provides Forced coverage of 3.7 - 4.2 m2/L/Coat
temperature reduction Anticarbonation
Technical Information
PROPERTIES SPECIFICATION RESULTS
Waterproofing Appearance Ready to use viscous liquid
DEEWARON KI Coverage
KHOOBSURATI Forced coverage of 3.7 - 4.2 m2/L/Coat
1. Surface Preparation
Product Features • Surface to be treated must be thoroughly cleaned and all loose material
must be removed.
Pore blocking • On existing efflorescence surface, clean all the efflorescence as per
3 years of Waterproofing market practice or by wire brushing followed by thorough water washing.
technology
• Small cracks up to 10mm or less should be opened, cleaned & filled with
Nerolac Perma Crack filler.
Efflorescence resistance
• Bigger cracks, damaged portions & hollow areas must be repaired with
Nerolac Perma Waterproof Polymer/Nerolac Perma Waterproof Latex
mechanism
modified mortar.
• Surface should be in SSD (saturated surface dry) prior the application of
Nerolac Perma Damp Lock.
High moisture resistance
up to 70%
• Existing putty to be removed till plaster level form skirting to the affected Specific gravity @ 300°C, g/cc
area covering an additional one ft distance across all sides of affected Application temperature
area.
Negative side water pressure ASTM D 4541: 2002
• Nerolac Perma Damp Lock is recommended to be applied on plaster by
brush ensuring material goes inside the pores/interstices.
Precautions and Recommendations
• Apply first coat of Nerolac Perma Damp Lock without dilution with a
forced coverage of 3.7 - 4.2 m2/L from skirting to the affected area, 1. Putty application over Nerolac Perma Damp Lock is mandotry.
covering an additional one ft distance across all sides of affected area. 2. Nerolac Perma Damp Lock is not be used with hand-made putty or lambi putty.
Allow it to dry for 6-8 hrs. 3. Do not apply primer or Topcoat directly over Nerolac Perma Damp Lock
• Apply 2nd Coat of Nerolac Perma Damp Lock without dilution with as it causes de-wetting.
coverage of 3.7 - 4.2 m2/L perpendicular to first coat. Allow it to dry for 4. Nerolac Perma Damp Lock is not applicable where moisture percentage is
6-8 hrs. more than 70% or there is a live leakage.
• Apply two coats of Nerolac cement wall putty or Nerolac acrylic wall 5. Do not apply when ambient temperature is less than 100C or the temperature
putty or Nerolac perma waterproof premium putty or Nerolac perm might drop to this level within 8 hours of application.
crystal waterproof putty over Nerolac Perma Damp Lock. Allow it to dry 6. Do not apply when humidity is greater than 90%, it may cause
for 6-8 hours and sand with sand paper 180. Wipe clean and paint it as pre-condensation on walls.
per regular painting practices. 7. Make sure that material is thoroughly stirred before application.
8. Subsequent coats of the topcoats to be done as per manufacturer's
b) For New Surfaces recommendation.
9. Please refer material safety data sheet (MSDS) of Nerolac Perma Damp Lock
• Apply a single coat of Nerolac Perma Damp Lock without dilution with a
for safety measures while handling the product.
forced coverage of not more than 3.7 - 4.2 m2/L. Allow it to dry for
6-8 hrs. Pack Size
• Apply two coats of Nerolac cement wall putty or Nerolac acrylic wall
putty or Nerolac perma waterproof premium putty or Nerolac perma Best before 24 months from the date of manufacture when kept
in sealed pack and stored under proper conditions
crystal waterproof putty over Nerolac Perma Damp Lock. Allow it to dry
for 6-8 hours and sand with sand paper 180. Wipe clean and paint it as
per regular painting practices. Shelf Life
Available in 1L & 4L packs.
Nerolac Perma Tile Adhesive Classic is a polymer modified grey cement based tile adhesive for fixing high
porosity tiles like ceramic, clay tiles, terracotta tiles and quarry tiles of regular size. It is suitable for
horizontal surfaces, over the cementitious substrate for indoor application in dry as well as in wet areas.
Product Features
Application Method
Surface must be thoroughly Mix Nerolac Perma Premium Stir continuously for 5-10 minutes
cleaned and all loose material Tile Adhesive with water as per min by hand or power mixer to
must be removed to ensure the recommended dosage obtain a homogenous paste
proper adhesion
Mix again for about 2 minutes Using a notched trowel, apply Using a notched trowel to remove
min the above mix to a thickness of excess material. Put the tile in
2-3 mm either on the wall and place and tap gently with a
on the back of the tile wooden hammer
Mixing - Nerolac Perma Eco Tile Adhesive to be mixed with water in the ratio of 3.5:1 by volume
Pack Sizes - Nerolac Perma Eco Tile Adhesive is available in the pack size of 20 kg and 50 kg
Precautions
KAHO Always add powder to water, do not add excess than the recommended.
APNE GHAR KO
Never add cement and sand at site.
Protect from direct rainfall and foot traffic for at least 24 hours.
JUG - JUG JIYO Note: For further more details please refer to TDS
Nerolac Perma Tile Adhesive Silver is polymer modified cement based tile adhesive for fixing ceramic,
semi-vitreous, vitrified tiles and natural stones of regular size. It is suitable for horizontal and vertical
surfaces, over the cementitious substrate for indoor application in dry as well as in wet areas and exterior
floor application. It is also recommended for tile on tile application.
Product Features
Application Method
Surface must be thoroughly Mix Nerolac Perma Premium Stir continuously for 5-10 minutes Allow the resultant paste to
cleaned and all loose material Tile Adhesive with water as per min by hand or power mixer to standfor about 10 minutes min
must be removed to ensure the recommended dosage obtain a homogenous paste
proper adhesion
Mix again for about 2 minutes Using a notched trowel, apply Using a notched trowel to remove For tile on tile application on
min the above mix to a thickness of excess material. Put the tile in interior vertical surface, apply bond
2-3 mm either on the wall and place and tap gently with a coat made of Nerolac Perma
on the back of the tile wooden hammer Waterproof Ploymer or Nerolac
Perma Waterproof Latex on the
back of tile and surface to be tiled,
Apply Nerolac Perma Premium Tile
Adhesive when bond coat is tacky
Mixing - Nerolac Perma Eco Tile Adhesive to be mixed with water in the ratio of 3.5:1 by volume
Pack Sizes - Nerolac Perma Eco Tile Adhesive is available in the pack size of 20 kg, 25 kg, 30 kg and 50 kg
Precautions
KAHO
APNE GHAR KO
Always add powder to water, do not add excess than the recommended.
Never add cement and sand at site.
JUG - JUG JIYO Protect from direct rainfall and foot traffic for at least 24 hours.
Note: For further more details please refer to TDS
Nerolac Perma Tile Adhesive Gold is polymer modified cement based tile adhesive for fixing ceramic,
semi-vitreous, vitrified tiles and natural stones on variety of surfaces for both vertical and horizontal interior
application, exterior floor application. It can be used in dry as well as wet areas for indoor as well as outdoor
application. It is also recommended for tile on tile application.
Product Features
Application Method
Surface must be thoroughly Mix Nerolac Perma Premium Stir continuously for 5-10 minutes Allow the resultant paste to stand
cleaned and all loose material Tile Adhesive with water as per min by hand or power mixer to for about 10 minutes min
must be removed to ensure the recommended dosage obtain a homogenous paste
proper adhesion
Mix again for about 2 minutes Using a notched trowel, apply Using a notched trowel to remove For tile on tile application on
min the above mix to a thickness of excess material. Put the tile in interior vertical surface, apply bond
2-3 mm either on the wall and place and tap gently with a coat made of Nerolac Perma
on the back of the tile wooden hammer Waterproof Ploymer or Nerolac
Perma Waterproof Latex on the
back of tile and surface to be tiled,
Apply Nerolac Perma Premium Tile
Adhesive when bond coat is tacky
Mixing - Nerolac Perma Eco Tile Adhesive to be mixed with water in the ratio of 3.5:1 by volume
Pack Sizes - Nerolac Perma Eco Tile Adhesive is available in the pack size of 25 kg and 50 kg
Precautions
KAHO
APNE GHAR KO
Always add powder to water, do not add excess than the recommended.
Never add cement and sand at site.
JUG - JUG JIYO Protect from direct rainfall and foot traffic for at least 24 hours.
Note: For further more details please refer to TDS
Nerolac Perma Tile Adhesive Diamond is polymer modified cement based tile adhesive for fixing
ceramic, semi-vitreous, vitrified tiles and natural stones on variety of surfaces for both vertical and
horizontal application. It can be used in dry as well as wet areas for indoor as well as outdoor
application. It is also recommended for tile on tile application.
Product Features
Application Method
Surface must be thoroughly Mix Nerolac Perma Premium Stir continuously for 5-10 minutes Allow the resultant paste to stand
cleaned and all loose material Tile Adhesive with water as per min by hand or power mixer to for about 10 minutes min
must be removed to ensure the recommended dosage obtain a homogenous paste
proper adhesion
Mix again for about 2 minutes Using a notched trowel, apply Using a notched trowel to remove For tile on tile application on
min the above mix to a thickness of excess material. Put the tile in interior vertical surface, apply bond
2-3 mm either on the wall and place and tap gently with a coat made of Nerolac Perma
on the back of the tile wooden hammer Waterproof Ploymer or Nerolac
Perma Waterproof Latex on the
back of tile and surface to be tiled,
Apply Nerolac Perma Premium Tile
Adhesive when bond coat is tacky
Mixing - Nerolac Perma Eco Tile Adhesive to be mixed with water in the ratio of 3.5:1 by volume
Pack Sizes - Nerolac Perma Eco Tile Adhesive is available in the pack size of 25 kg and 50 kg
Precautions
KAHO
APNE GHAR KO Always add powder to water, do not add excess than the recommended.
Never add cement and sand at site.
JUG - JUG JIYO Protect from direct rainfall and foot traffic for at least 24 hours.
Note: For further more details please refer to TDS