Versathane Spray Grade PDS

Issue No.
02 Sep 2022
VERSATHANE SPRAY GRADE Page 1 of 2
PRODUCT A high build solvent free polyurethane anticorrosive coating. Highly resistant to marine and industrial
DESCRIPTION environments, buried conditions, ground water, effluents, salt water, and a wide range of oils and chemicals.
Extremely abrasion resistant, high mechanical strength.
INTENDED USES Designed for the efficient long term protection of steel and concrete structures in aggressive environments.
Will provide long term protection to the internal and external surfaces of pipelines and field joints. Suitable for
chemical plants, land and marine structures etc. Service temperature range -20°C to +80°C.
Meets the performance requirements of GIS/CW6: 2020
Meets the performance requirements of BS EN 10290
Meets the performance requirements of AWWA C222
BS6920 WRAS Water Fittings Directory Certificate 2206509
TECHNICAL
INFORMATION Colour Grey (18B21), Blue (18E53), Cream, additional colours available
Finish Semi-gloss
Curing Agent Versathane Spray Applied Activator
Mix Ratio 3 parts Base : 1 part Activator by volume
Specific Gravity Base: 1.30 Activator: 1.22 Mixed: 1.28
Volume Solids 100%
Recommended Film Thickness 1.0 - 1.5 mm depending on service conditions. Can be applied up to
5 mm in one continuous wet on wet application.
Theoretical Spreading Rate 1 m² / litre @ 1000µm
Application Method Plural component hot airless spray
Re-coat After 1 hour and within 24 hours of initial application.
Drying Times at 20ºC Touch Dry 30 minutes Hard Dry 4 hours
Full Cure at 20ºC 7 days to Shore D65-80
SURFACE Steel:
PREPARATION
Ensure surfaces are free from contamination. Prepare surfaces by abrasive blast cleaning to ISO
8501-1 Sa 2 ½. - surface profile depth 75-100 microns.
Concrete:
Remove all laitance and other contaminants by blast cleaning. Ensure the concrete is dry to a reading of less
than 10% moisture. Seal with Versacure Mortar LV Sealer.
Advanced Barrier Coatings Limited Commissioners Quay Quay Road Blyth Northumberland NE24 3AG
Tel: +44 (0)1670 338414 E-mail: info@advancedbarriercoatings.com Web: www.advancedbarriercoatings.com
Registered in England No 9532651 VAT No 211306567
Issue No.02 Sep 2022
VERSATHANE SPRAY GRADE Page 2 of 2
APPLICATION The temperature of the substrate must be at least 30C above the dew point during application and relative
humidity below 80%.
The surface must be kept clean and dry, and VERSATHANE or DURA-LINK TC applied within 4 hours and
before any visible signs of deterioration of the cleaned surface.
Application by two component spray system set at 3:1 mixing ratio.

Base temperature approx. 40 - 50oC
Hardener temperature approx. 15 - 25oC
Spray Tip Size 600 - 1000 microns (0.024 - 0.038 “)
Cleaning solvent. All equipment must be cleaned thoroughly immediately after use with Pracsolv 1
REGULATORY DATA Packaging Supplied in 820 litre units consisting of 3 x 205 litres base:1 x 205 litre hardener
and 80 litre composite packs consisting of 3 x 20 litres base:1 x 20 litre hardener
Flash Point 200°C
VOC 0 g/litre
Shelf life: 24 months from date of manufacture when stored in the original sealed containers at 20°C.
Hardener component contains Diisocyanates and as from 24.08.23 adequate training is required before
industrial or professional use.
SAFETY Refer to the product Material Safety Data Sheet supplied by Advanced Barrier Coatings Ltd.
PRECAUTIONS Ensure all waste materials and empty containers are disposed of in accordance with local regulations.
Disclaimer The information given in this technical data sheet - whether verbal, or in writing is for guidance only and is given in good faith, but without
warranty. This also applies where proprietary rights or third parties are involved. Any person using Advanced Barrier Coatings Ltd products
without first making further enquiries as to the suitability of the products for the intended purpose and testing the products to assess their
fitness for the purpose does so at their own risk. The application and surface preparation are beyond our control and are therefore your own
responsibility, and we can accept no liability for the performance of the products arising out of such use. The information contained in this
data sheet is liable to modification at any time and It is the user's responsibility to ensure that this sheet is current prior to using the product.
Advanced Barrier Coatings Limited Commissioners Quay Quay Road Blyth Northumberland NE24 3AG
Tel: +44 (0)1670 338414 E-mail: info@advancedbarriercoatings.com Web: www.advancedbarriercoatings.com
Registered in England No 9532651 VAT No 211306567

Versathane Spray Grade PDS

Uploaded by

Copyright:

Available Formats

Versathane Spray Grade PDS

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Versathane Spray Grade PDS

Uploaded by

Copyright:

Available Formats

Issue No.

Meets the performance requirements of GIS/CW6: 2020

Meets the performance requirements of BS EN 10290

Meets the performance requirements of AWWA C222

BS6920 WRAS Water Fittings Directory Certificate 2206509

Curing Agent Versathane Spray Applied Activator

Mix Ratio 3 parts Base : 1 part Activator by volume

Specific Gravity Base: 1.30 Activator: 1.22 Mixed: 1.28

Volume Solids 100%

Theoretical Spreading Rate 1 m² / litre @ 1000µm

Application Method Plural component hot airless spray

Re-coat After 1 hour and within 24 hours of initial application.

Drying Times at 20ºC Touch Dry 30 minutes Hard Dry 4 hours

Full Cure at 20ºC 7 days to Shore D65-80

Application by two component spray system set at 3:1 mixing ratio.

and 80 litre composite packs consisting of 3 x 20 litres base:1 x 20 litre hardener

Flash Point 200°C

You might also like