MO 6700D+SeriesEM00 e

®
HIGH SPEED SEMI-DRY HEAD OVERLOCK/INTERLOCK/

SEWING MACHINE
MO-6700D Series
ENGINEER’S MANUAL
40033638
No.E368-00
PREFACE
This Engineer’s Manual is written for the technical personnel who are responsible for the service and maintenance
of the machine.
The Instruction Manual for these machines intended for the maintenance personnel and operators at an apparel
factory contains operating instructions in detail. And this manual describes “Standard Adjustment”, “Adjustment
Procedures”, “Results of Improper Adjustment”, and other important information which are not covered by the
Instruction Manual.
It is advisable to use the relevant Instruction Manual and Parts List together with this Engineer’s Manual when
carrying out the maintenance of these machines.
In addition, for the motor for the sewing machine with thread trimmer, refer to the separate Instruction Manual or
Engineer’s Manual for the motor. And for the control panel, refer to the Instruction Manual for the control panel.
This manual gives the “Standard Adjustment” on the former page under which the most basic adjustment value is
described, and on the latter page “Results of Improper Adjustment” under which stitching errors and troubles
arising from mechanical failures are described together with the “Adjustment Procedures”.
CONTENTS
1. SPECIFICATIONS .......................................................................................... 1
(1) MO-6700D SERIES ...................................................................................................... 1
2. MODEL NUMBERING SYSTEM .................................................................... 2
3. STANDARD ADJUSTMENT .......................................................................... 4

(1) Adjusting the needle height ....................................................................................... 4
(2) Positioning the throat plate ....................................................................................... 4
(3) Installing position of the needle clamp .................................................................... 6
(4) Adjusting the length of the lower looper holder
(Applicable only to MO-6716D series) ...................................................................... 6
(5) Adjusting the lower looper ........................................................................................ 8
1) Returning amount of the lower looper ..................................................................................................8
2) Clearance between the lower looper and the needle ...........................................................................8
(6) Position of the upper looper guide ......................................................................... 10
(7) Positioning the upper looper holder ....................................................................... 12
(8) Positioning the upper looper ................................................................................... 14
1) Height of the upper looper ..................................................................................................................14
2) Longitudinal position of the upper looper ...........................................................................................14
(9) Adjusting the double chain looper (Applicable only to MO-6716D series) ......... 16
1) Returning amount of the double chain looper ....................................................................................16
2) Longitudinal motion (Avoid motion) ....................................................................................................16
3) Clearance between the double chain looper and the needle .............................................................16
(10) Adjusting the height and clearance of the needle guard ...................................... 18
1) For 1-needle or 2-needle overlock machine .......................................................................................18
2) For safely stitch machine ...................................................................................................................18
(11) Adjusting the height of the feed dog ...................................................................... 20
(12) Adjusting the tilt of the feed dog ............................................................................. 20
(13) Adjusting the differential feed ratio ........................................................................ 22
(14) Longitudinal position of the feed dog .................................................................... 22
(15) Adjusting the presser foot ....................................................................................... 24
1) Adjusting the tilt of the presser foo .................................................................................................... 24
2) Adjusting the micro-lifting mechanism of the presser foot ................................................................. 24
(16) Positioning the upper knife arm shaft .................................................................... 26
(17) Positioning the upper and lower knives, and available overedge widths ........... 26
1) Lower knife .........................................................................................................................................26
2) Upper knife .........................................................................................................................................26
3) Overdging width .................................................................................................................................26
(18) Resharpening of the knife ........................................................................................ 28
(19) Position of the thread cam (Applicable only to MO-6716D series) ...................... 28
1) Adjustment of the thread cam ............................................................................................................28
2) Adjusting looper thread cam thread guides A and B and the looper thread cam nail ......................... 28
3) Adjusting looper thread auxiliary thread take-up lever (Exclusive for 30P) ........................................ 30
(20) Adjusting the throat plate support .......................................................................... 32
(21) Adjusting the feed mechanism cover presser ....................................................... 32
(22) Adjusting the looper cover ...................................................................................... 34
(23) Adjusting the cloth chip cover ................................................................................ 34
(24) Position of the thread guides and the looper thread take-ups............................. 36
(25) Adjusting soft chain making mechanism ............................................................... 38
1) Replacing the parts with those exclusively designed for making soft chains ..................................... 38
2) Adjustment value ................................................................................................................................38
3) Important points in adjustment ...........................................................................................................39
4. ADDITIONAL INFORMATION AND PRECAUTIONS .................................. 40

(1) Thread tension ............................................................................................................ 40
1) Strength of tension spring ..................................................................................................................40
2) Springs used for each model .............................................................................................................40
(2) Upper looper ............................................................................................................. 40
(3) Center-to-center distance of the upper looper holder .......................................... 41
(4) Caution in assembly ................................................................................................. 41
1) Application of sealant .........................................................................................................................41
2) Precautions to be taken with respect to the lubricating components ................................................. 43
3) Applying the exclusive grease ............................................................................................................44
(5) Kinds of motor pulleys, belts and frame support plate bolts ............................... 46
1) Motor pulleys and belts ......................................................................................................................46
2) Pat No. of frame support plate bolt ....................................................................................................46
5. ADJUSTMENT VALUES OF THE NEEDLE HEIGHT

AND LOOPER TIMING ................................................................................ 47
(1) MO-6700D SERIES .................................................................................................... 47
6. TROUBLES AND CORRECTIVE MEASURES ........................................... 48
7. DIMENSIONS OF TABLE ............................................................................ 60

(1) Semi-sunken type ..................................................................................................... 60
(2) Semi-sunken type (synchronizer is used) .............................................................. 61
(3) Fully-sunken type ..................................................................................................... 62
1. SPECIFICATIONS
(1) MO-6700D SERIES
No. Item Specifications
1 Model MO-6704D MO-6714D MO-6716D
2 Description 1-needle Overlock 2-needle Overlock 2-needle Safety stitch

machine machine machine
3 Stitch type F. S. T. JIS E13 JIS E24 JIS E13+D12
(USA standard : 504) (USA standard : 514) (USA standard : 516)
4 Sewing speed 6000rpm

5 Stitch length 0.8 to 4mm 1.5 to 4mm
6 Needle gauge 2.0, 3.2mm 3.2, 4.8mm
7 Overedging width 1.6, 3.2, 4, 4.8mm 2.0, 3.2, 4mm 3.2, 4, 4.8, 6.4mm
8 Differential feed ratio Gathering 1 : 2 (Max.1 : 4), Stretching 1 : 0.7 (Max.1 : 0.6)
9 Needle bar stroke 24.5 mm (30P for light to medium-weight materials),
25.5 mm (40H for medium to heavy-weight materials)
10 Needle tilt angle 20°
11 Needle bar mechanism Upper and lower needle bar bushing type
12 Needle ORGAN DC X 27 (Standard) (DC X 1 can be used as well.)
13 Presser lifting amount 7.0mm 6.5mm 7.0mm
14 Presser foot pressure 49N (5kg)
15 Stitch adjusting method By pushbutton
16 Upper knife Flat knife
17 Differential feed adjustment By lever with micro adjustment mechanism
18 Weight 28kg
19 Lubrication Automatic geared lubrication system and grease charge
20 Lubricating oil JUKI MACHINE OIL 18 (Equivalent to ISO VG 18) Product No.: MML018900CA
21 Grease Exclusive grease (Part No. 23640204)
22 Needle cooler Optional
23 Needle thread cooler Optional
24 Micro presser lifting device Provided as standard
25 Motor 2P 400W
*1. Grease should be supplied to the needle bar system and upper looper system.
–1–
2. MODEL NUMBERING SYSTEM
MO-6700D SERIES MODEL NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
MO6 7 D /
3 to 6 Model classification 7 Type classification

6704 1-needle 3-thread overlock D Semi-dry head
6705 Blind-hemming
6712 2-needle, 4-thread imitation safety stitch
6714 2-needle 4-thread overlock
6716 2-needle 5-thread safety stitch
6743 3-needle 6-thread safety stitch
6745 2-needle double chain stitch
8 Needle gauge classification 9 Overedging width classification 10 Feed dog classification

0 1-needle A 1.6mm 4 2-row
B 2.0mm B 2.0mm 5 1-row
D 3.2mm D 3.2mm 6 3-row
F 4.8mm E 4.0mm
* 1 4.8+2.0mm F 4.8mm
* 2 3.2+2.0mm H 6.4mm
The asterisk (*) indicates 3-needle type.
11 Material classification
(classification applied to handling material and cloth)
1 Extra light- to right-weight material Light weight material such as dress shirt
2
3 Light- to medium-weight materials General fabrics
4 Meduim- to heavy-weight materials Exclusive for knit such as sweater
5 Medium weight material such as denim to heavy weight material
12 Application classification
(classification of application based on work and process)
0 Standard
1 For blind hemming
2 For ruffling
4 For tape attaching
5 For rolled hemming
6 For tape feeding
–2–
13 Special machine classification
(special classification of machine,
structure and specs. other than gauge set)
0 Standard
7 Upper looper high throw
F Swim suits
H Upper looper extra high lift
P Puckering prevention
15 to 22 Device and attachment classfication

G39/Q141 Presser for tape attaching (for sharp curve)/tape guide
L121 Blind stitch hemming attachment
S159 Swing-type gathering device (interlocked with pedal, for safety stitch machine)
S162 Swing-type gathering device (manual lever operated, for overlock machine)
N077 Clean finish top and bottom
E35 Overedging lug replace type throat plate
24 Place of destination 25 Accessories type

A Standard A Standard
D U.S.A and Japan B Eouropa and U.S.A
G China (in China) G China (in China)
26 Table type
0 Fully sunken type
1 Semi sunken type
–3–
3. STANDARD ADJUSTMENT
(1) Adjusting the needle height
Standard Adjustment
When the needle(s) is in the highest position, the needle height from the throat plate surface should be as
shown below.
(Unit : mm)
6704D Model Dimension A Dimension B Dimension C
6705D 1-needle overlock
MO-6704D-0A -150 10.5 — —
MO-6705D-0 -210 10.5 — —
machine
MO-6704D-0 -300 10.5 — —

A
MO-6704D-0 -307 10.5 — —
MO-6704D-0 -40H 11.3 — —
6712D
MO-6704D-0F6-50H 11.3 — —
6714D
2-needle overlock
MO-6714D-B - 7 10.5 9.1 —

machine
MO-6714D-B - H 11.3 9.9 —

A B MO-6712D-DF6-50 11.0 9.4 —
MO-6714D-B -30P 10.5 9.1 —
MO-6716D- -300 10.5 — 9.8
6716D
Safety stitch
machine
MO-6716D-FF6-307 10.5 — 9.8

MO-6716D- -4 H 11.3 — 10.6
50H
A MO-6716D- -30P 10.5 — 9.8
C
The adjustment of needle height for the 2-needle overlock machine should be
made in reference to the left needle.
(2) Positioning the throat plate

Standard Adjustment
The needle entry point should be such that the distances listed below are provided between the needle slot
edge of the throat plate and the center of needle.
For 30P
(Safety stitch machine)
(Unit : mm)
Overlock side A 1.3
Double-chainstitch side B 1.0
A
B
10°
–4–
Adjustment Procedure Results of Improper Adjustment
1) Take off the upper cover, loosen setscrew of needle driving forked o Any other needle height than
crank and move needle driving forked crank up or down to adjust specified here will badly affect the
the needle height. action of the lower looper, the
timing for catching the upper
looper thread, etc.
Needle driving shaft
o Improper lateral position of the

(Caution) Do not fully loosen the setscrew of the needle driving needle driving forked crank will
forked crank . cause seizure, play, or other
If the needle driving forked crank has got out of position troubles.
laterally when its setscrew was loosened, fully loosen the
setscrew and turn pulley to allow the forked crank to turn
until it settles by itself. Then tighten the setscrew to fix
the forked crank at that position.
1) Loosen setscrews of throat plate base and move throat plate o Improperly positioned throat plate
base back and forth to adjust dimension A or B. with cause needle breakage,
contact of the needles will the
throat plate, or other troubles.
–5–
(3) Installing position of the needle clamp
Standard Adjustment
Needle clamp connecting stud should fit with the bottom end of needle bar or be spaced within 0 to 0.5
mm.
0 to 0.5mm
Butt the needle clamp with the

bottom end of the needle bar.
(4) Adjusting the length of the lower looper holder (Applicable only to MO-6716D series)
Standard Adjustment
The center-to-center distance should be 26 mm.

At this time, the clearance between the end surface of the arm and the neck of the ball should be 3.5mm.
26mm
3.5mm
–6–
1) Loosen setscrew and adjust, by slightly turning needle clamp , o If the clearance provided
the clearance provided between the right-hand side needle and the between the needle and the
lower looper (for 2-needle overlock machine) and the clearance looper is excessive, the needle
provided between the needle hole in the throat plate and the needle thread will be likely to skip at the
(for safety stitch machine). time of tucking.
o If the clearance provided
between the needle and the
looper is insufficient, the needle
will break or the looper blade
point will be damaged causing
thread breakage.
1) Loosen setscrew of the lower looper holder from the rear of the o Increasing the center-to-center
frame. distance will give a smaller stroke
Since it is difficult to accurately measure the center-to-center distance, of the double chain looper or
perform adjustment to provide a 3.5 mm distance between the end lower looper, and decreasing the
surface of the arm and the neck of the ball as illustrated. distance will give larger stroke.
–7–
(5) Adjusting the lower looper
Standard Adjustment
1) Returning amount of the lower looper

The distance between the blade point of the lower (Unit : mm)
looper and the center of the needle should be as Model Dimension J
follows when the lower looper is at the extreme
left of its stroke. MO-6704D-0A -150 4.0
MO-6705D-0 -210 4.0
1-needle overlock
machine
J MO-6704D-0 -300 3.8
MO-6704D-0 -307 3.8
MO-6704D-0 -40H 3.8
MO-6704D-0F6-50H 3.8
2-needle overlock
MO-6714D-B - 7 3.8
machine
MO-6714D-B - H 4.0
(66.9±0.2mm)
MO-6712D-DF6-50 2.2
MO-6714D-B -30P 3.8
MO-6716D- -300 3.8
K
Safety stitch
MO-6716D-FF6-307 3.8
machine
MO-6716D- -4 H 3.8
50H
MO-6716D- -30P 3.8
2) Clearance between the lower looper and the needle

The clearance should be 0.01 to 0.1 mm.
0.01 to 0.1 mm
–8–
o Excessive return of the lower

1
1) Returning amount of the lower looper
Loosen setscrew of lower looper support arm and adjust lower looper tends to cause stitch
skipping when filament thread is
looper to make adjustment of the returning amount.
used.
o Insufficient return of the lower
(Referential information)
lopper tends to cause needle
1. Radius K of lower looper will be 66.9 mm when the lower
thread stitch skipping when spun
looper is inserted into lower looper support arm until it con-
thread is used.
tacts with stopper pin and then is fixed.
2. The rocking angle of the lower looper will be 26°.
1
2) Clearance between the lower looper and the needle o Excessive clearance will often
Loosen setscrew of lower looper support arm to the extent that cause needle thread stitch
it is temporarily tightened. Then finely adjust the longitudinal position skipping.
2
of the looper using fine adjustment screw . o Insufficient clearance will cause
Turn fine adjustment screw clockwise to move lower looper away needle breakage due to the con-
from the needle. tact of the looper with the needle,
Turn the screw counterclockwise to move lower looper closer to it. or produce scratches on the
blade point of the looper, lead-
ing to needle thread breakage or
other troubles.
–9–
(6) Position of the upper looper guide
Standard Adjustment
Vertical position : To be in close contact with the frame guide surface.

Laternal position : To be pressed against the upper looper guide support gauge .
(Unit : mm)
G
Upper looper guide

7 5.5 6.3 4.7
support gauge
6
5.8
Marker dot 13131909 13132006
Frame guide surface
(Unit : mm) (Unit : mm)

Model Dimension G Model Dimension G
6.3
Safety stitch
MO- 6716D - - 30P

1-needle overlock
machine
machine
5.8 D 5.8
MO- 6716D - -4 H
MO- 6704D - 0E to 0F - 4 H F
2-needle overlock
MO- 6714D - BB6 to BE6 - 30P

machine
5.8
BD4 to BE4
MO- 6714D - -4 H
BD6 to BE6
– 10 –
1) Fit upper looper guide support gauge over gauge fixing pin which o If the upper looper guide has
has been driven in frame and secure the gauge with an O ring. improperly positioned vertically,
Then position the gauge taking the marker dot engraved on it or the it will cause oil leakage or
chamfering direction as reference. disturbed path of the upper
2) When installing upper looper guide support , press it against the looper with resultant stitch
gauge while keeping the upper looper guide support into close con- skipping.
tact with the frame guide surface, then tighten the screws. o If the upper looper guide has
(Caution) Refer to “4- (4) -1) – 7 Various sealantsî for the various been inaccurately positioned lat-
erally, it will cause stitch skipping,
sealants. or contact with the looper.
– 11 –
(7) Positioning the upper looper holder
Standard Adjustment
The distance between the bottom surface of the frame and the upper end of the upper looper holder pin
should be as shown below when the upper looper holder is at the highest point of its stroke.
(Unit : mm)
Model Dimension F
1-needle overlock
machine
MO- 6704D - 0E to 0F -4 H 48.2
53mm
2-needle overlock
Bottom surface of frame MO- 6714D - BB6 to BE6 - 30P 47.3

machine
BD4 to BE4
MO- 6714D - -4 H 48.4
BD6 to BE6
Safety stitch
MO- 6716D - - 30P 46.2

machine
MO- 6716D - D -4 H 48.2

F
0.2mm 0.2mm
– 12 –
1) Loosen the setscrew of upper looper ball arm and setscrew of o Inaccurately positioned upper
the upper looper holder. looper holder will cause
2) Adjust the clearances between upper looper bracket and upper excessive projection of the upper
looper holder to approximately 0.2 mm respectively, and tighten looper, resulting in stitch
setscrew of the upper looper holder. skipping, or contact.
(Make sure that the upper looper holder smoothly moves together (Caution) To adjust the upper
with upper looper shaft .) looper ball arm, take
3) Then determine dimension F from the bottom surface of the frame to dimension F as stan-
the top surface of upper looper holder pin before tightening the dard.
Remember that the
setscrew of upper looper ball arm .
projecting amount
(Caution) Replace upper looper holder according to the needle and the height of the
gauge size. upper looper should
eventually be prop-
erly adjusted. So,
confirm the dimen-
sions related to the
upper looper.
– 13 –
(8) Positioning the upper looper
Standard Adjustment
1) Height of the upper looper

The distance between the throat plate surface and the blade point of the looper should be as follows when
the upper looper is at the extreme left of its travel.
E (Unit : mm)
Model Dimension D Dimension E
D MO-6704D-0A -150 11.0 4.0
1-needle overlock
MO-6705D-0 -210 11.0 4.0
E
machine
MO-6704D-0 -300 11.0 4.0
MO-6704D-0 -307 10.3 4.4
D
MO-6704D-0 -40H 11.3 4.4
MO-6704D-0F6-50H 11.3 4.4
E
2-needle overlock
MO-6714D-B - 7 10.3 4.4

machine
MO-6714D-B - H 10.5 4.8

MO-6712D-DF6-50 11.0 3.6
MO-6714D-B -30P 10.3 4.4
MO-6716D- -300 11.0 4.0
Safety stitch
machine
MO-6716D-FF6-307 10.3 4.4

D MO-6716D- -4 H 11.3 4.4
50H
MO-6716D- -30P 11.0 4.0
Throat plate
2) Longitudinal position of the upper looper

1The clearance between upper looper and lower looper should be 0.05 to 0.2 mm when they cross
with each other.
2 The clearance between upper looper and needle should be 0.01 to 0.2 mm.
0.05 to 0.2 mm
0.01 to 0.2 mm
– 14 –
1
1) Height of the upper looper o If the upper looper has been
Set a hexagon wrench key onto setscrew at the end of upper looper positioned too high, an excessive
2
bracket to adjust height D . clearance will be produced
When adjusting the height, pay attention also to the clearance pro- between the upper looper and
duced between the upper looper and lower looper at the time of the needle. As the result, the
their crossing. upper looper thread will fail to
catch the needle thread, and
stitch skipping occurs.
o On the contrary, if the upper
looper has been positioned too
low, the needle point will hit the
looper, causing needle break-
age. Also the looper will touch
other component when the
presser foot goes up.
1
2) Longitudinal position of the upper looper o Excessive clearance will cause
Loosen setscrew at the top end of upper looper bracket to move stitch skipping.
upper looper back or forth for positioning the clearance of 0.05 to o Insufficient clearance will cause
0.2 mm between upper looper and lower looper at the time of the upper looper to come in con-
their crossing or the clearance of 0.01 to 0.2 mm between upper looper tact with the lower looper.
and needle .
– 15 –
(9) Adjusting the double chain looper (Applicable only to MO-6716D series)
Standard Adjustment
1) Returning amount of the double chain looper

The distance between the needle center and the blade point of the double chain looper should be 1.5 to 1.7
mm when the looper is at the extreme left of its travel.
1.5 to 1.7 mm
m)
4m
M
(63.
2) Longitudinal motion (Avoid motion)

The standard minor axis of the elliptical motion should be :
3.0 mm.
Note : The avoid motion should be adjusted in accordance with Needle No.
Marker
3.0 to 3.6 mm
B A
Marker
Hole
3) Clearance between the double chain looper and the needle

The clearance should be 0.05 to 0.1 mm.
0.05 to 0.1 mm
– 16 –
o Excessive return of the double

1
1) Returning amount of the double chain looper
Loosen setscrew of double chain lopper driving arm to make chain looper will cause frequent
stitch skipping when filament
2
this adjustment.
Radius M of the double chain looper driving arm will be 63.4 mm thread is used.
when it is lowered until it comes in contact with stopper pin . o Insufficient return of the double
chain looper will cause frequent
thread stitch skipping when a
spun thread is used.
1
2) Longitudinal motion (Avoid motion) o If the avoid motion is too large,
Open the cover of the adjusting hole on the rear of the frame, loosen triangle stitch skipping will often
setscrew , and put a Ø2 rod in the hole. Now, make the adjustment occur.
by turning the rod back and forth.
Bad needle
Marker : This side entry
..... Minimum (for standard to thin needle) A As observed
Marker : Far side from this side Good needle
..... Maximum (for thick needles) B entry
o Insufficient avoid motion will

cause the needle point to hit the
looper, producing scratches on
the needle point or looper.
1
3) Clearance between the double chain looper and the needle o Excessive clearance will cause
Temporarily tighten setscrew in the double chain looper, and finely frequent needle thread stitch
adjust the longitudinal position of the double chain looper. Adjust the skipping.
clearance to 0.05 to 0.1 mm. o Insufficient clearance will cause
to looper to hit the needle, lead-
ing to needle breakage or
scratches on the looper blade
point with consequent thread
breakage.
– 17 –
(10) Adjusting the height and clearance of the needle guard
Standard Adjustment
1) For 1-needle or 2-needle overlock machine

The overlock machine has two needle guards, A and B .
The needle guard B should be located 1 mm below the throat plate bottom surface.
Needle guard A Needle guard B
Throat plate
(Traveling needle guard)
1 mm
Light
touch
the
A
needle B
guard
0.1 mm
2) For safely stitch machine

The safely stitch machine has four needle guards, A , B , C and D . The needle guards A and B are
positioned in the same manner as those for the overlock machine.
The needle guard C should be positioned 5 mm below the throat plate bottom surface.
Throat plate
5 mm
Lightly touches
C
0.1
mm
– 18 –
1
1) For 1-needle or 2-needle overlock machine o Excessively close contact
Adjust needle guard A with setscrews in the needle guard so that between the needle guard A
it lightly comes in contact with the needle when the blade point of the and the needles will lead to
needle bend or stitch skipping.
2
lower looper reaches the needle center.
To adjust the clearance provided between needle guard B and the o A clearance left between the needle
needle when the needle bar is at the lowest point of its stroke, loosen guard A and the needles will cause
setscrews in the needle guard support and turn needle guard B to the looper blade point to come in
contact with the needles, leading to
3
adjust the clearance to 0.1 mm.
Adjust the height of needle guard B to 1 mm from the throat plate needle or blade point breakage, or
other troubles.
bottom surface with setscrew in the needle guard.
o If the needle guard B is too high,
thread loops will be damaged
with resultant stitch skipping.
Also, double chain loops will be
affected, causing double chain
stitch skipping.
o If the needle guard B is too low,
the needle cooling felt will be low-
ered, resulting in deteriorated effect
of the cooling and needle guard.
o Excessive clearance between
the needle guard B and the
needle will cause stitch skipping
due to needle shake. On the con-
trary, insufficient clearance will
cause the needle guards to catch
the needles between them, lead-
ing to wear on the needle guards
and scratches on the needles.
1
2) For safety stitch machine o If the needle guard C is too high,
Loosen setscrews in the needle guard, and adjust the clearance the needle thread loops will be
provided between needle guard C and the needle so that it lightly damaged, and stitch skipping
2
comes in contact with the needle. occurs. If it is too low, the needle
Adjust the installing height of needle guard C to 5 mm with setscrew points will be crushed.
o If the clearance between the
3
in the needle guard.
Adjust the clearance provided between needle guard D and the needle needle guard C and the needles
to 0.1 mm with setscrews . is too large, the double chain
(Caution) Check again the clearance provided between needle guard looper blade point will come in
B and the needle after adjusting the height of needle
contact with the needles, causing
guard C . the breakage of the needles,
causing the breakage of the
needles or looper blade point.
No clearance left between them
will cause them to come in exces-
sively close contact with each other,
and bend of needle, wear on the
needle guard and scratches on the
needles will occur.
o Excessive clearance left be-
tween the needle guard D and
the needles will cause stitch skip-
ping due to needle shake, and
insufficient clearance will cause
the needle guards to catch the
needles between them, leading
to wear on the needle guards
and scratches on the needles.
– 19 –
(11) Adjusting the height of the feed dog
Standard Adjustment
The height of main feed dog from the top surface of the throat plate should be as follows when it is at its
highest position. (Unit : mm)
Needle A Model Dimension A
entry
MO-6700D series (30P excluded) 1.0
MO-67 D- -30P 0.8
[Standard]
Auxiliary feed dog is 0.5 mm lower than main feed dog .
B = 0.5 mm
[30P]
Auxiliary feed dog is as high as main feed dog .
B = 0 mm
(12) Adjusting the tilt of the feed dog
Standard Adjustment
Tilt of the feed dogs when When the feed dog juts In case of 30P type
the feed dogs have come out the top surface of
up most. the throat plate
15°
Needle A B Top surface of Feed dog is leveled.
entry the throat plate
Front up
(Unit : mm)
Model Dimension A Dimension B
MO-6700D series (30P excluded) 1.0 (1.2)
MO-67 D- -30P 0.8 (0.9)
– 20 –
1) Adjust the height of main feed dog to dimension A with setscrew o If the feed dogs are too high, the
. needles will be deflected and
2) Adjust the height of differential feed dog with setscrew so that broken when sewing heavyweight
there is no difference in level between main feed dog and differen- materials. The feed dogs will tend
tial feed dog . to suffer scratches when sewing
3) Adjust the height of auxiliary feed dog with setscrew so that it is light-weight materials. Puckering
0.5 mm lower than main feed dog . will frequently occur.
o If the feed dogs are too low, in-
sufficient feed power will result.
o If the auxiliary feed dog is too
high, chain-off thread will be of-
ten jammed.
o If the main feed dog and differ-
ential feed dog are set at differ-
ent heights, proper differential
feeding action will be hindered.
1) Use the tilt of the feed dog when it is in its highest position as a o When tilted with the front up
reference and adjust so that the feed dog is flush with the throat plate Good material catching will be
when the feed dog juts out the throat plate. obtained.
2) Feed bar shaft consists of an eccentric shaft. Loosen setscrew o When tilted with the front down
to perform adjustment. Uneven feed and puckering will
When the marker line is set at middle be effectively prevented.
.....The feed dog will be flat.
When the marker line is set at bottom
.....The feed dog will be tilted with its front up (in the arrowed direc-
tion).
When the marker line is set at top
.....The feed dog will be tilted with its front down.
(Caution) The marker line should be used just as the reference since
it slightly differs with that of each machine due to the
disparity of the components.
Confirm the accurate tilt of the feed dog by observing
the feed dog itself.
– 21 –
(13) Adjusting the differential feed ratio
Standard Adjustment
Pin at its highest

position Washer
Pin at its lowest
Center of position
nut Lower
marker line
(Standard) (Max, stretching) (Max, gathering)

Gathering: 1: 2 Gathering: 1:1.6 Gathering: 1: 4
Stretching: 1: 0.7 Stretching: 1:0.6 Stretching: 1: 1.3
(14) Longitudinal position of the feed dog
Standard Adjustment
When the feed pitch is maximized and the differential feed ratio is also maximized, the clearances of the front
and rear ends of the feed dog, and the throat plate should be spaced approximately 0.5 mm respectively.
0.5mm
0.5mm
– 22 –
1) Remove cover on the rear of the frame and loosen main feed pin
and nut .
2) Move main feed pin up or down to adjust the differential feed ratio.
3) Adjust so that the lower engraved marker line on main feed rocker
aligns with the center of nut . (Standard)
4) When adjusting the maximum stretching, adjust main feed pin to
the highest position.
5) When adjusting the maximum gathering, adjust main feed pin to
the lowest position.
6) After performing adjustment, tighten the main feed pin and nut ,
and install cover .
1) Remove the cover on the rear of the frame, loosen main feed bracket o If the clearance provided
clamping screw and differential feed bracket clamping screw , between the throat plate and the
and adjust the clearances provided between the front and rear ends feed dog is too small, they will
of the feed dogs and the slots in the throat plates to approximately come in contact with each other
0.5 mm. Then tighten main feed bracket clamping screw and when the sewing machine runs
differential feed bracket clamping screw . at high speed
– 23 –
(15) Adjusting the presser foot
Standard Adjustment
1) Adjusting the tilt of the presser foot

The presser foot should be positioned so that the feed dogs go down under the specified presser foot
pressure, and the presser foot sole comes in contact evenly with the throat plate surface.
Throat plate
2) Adjusting the micro-lifting mechanism of the presser foot
– 24 –
1
1) Adjusting the tilt of the presser foot o Uneven contact will result in bad
Turn the handwheel and place the feed dog in the position where the straight material feed and weak
2
feed dog does not jut out the top surface of the throat plate. feed force. Puckering is apt to
Loosen setscrew and adjust so that the presser foot sole comes in occur as well.
contact evenly with the throat plate top surface. Then tighten set-
screw .
(Reference) Accurate adjustment can be made by using two pieces
of thin paper to check for even drawing-out tension.
In addition, even contact of the presser foot with the
throat plate top surface is achieved rather easily by
tightening the screw while pushing the right side of
the presser foot.
1
2) Adjusting the micro-lifting mechanism of the presser foot
When moving presser lifting lever just a little, perform it with fine
adjustment screw .
– 25 –
(16) Positioning the upper knife arm shaft
Standard Adjustment
The upper knife shaft should be positioned 34 mm above the top surface of the throat plate when it is at its
highest position.
34mm
(17) Positioning the upper and lower knives, and available overedge widths
Standard Adjustment
1) Lower knife
Throat plate
Lower knife
2) Upper knife
0.5 to 1 mm
Upper knife
3) Overedging width
Overedging width can be adjusted from 1.6 to 6.4 mm.
– 26 –
1) Remove the upper cover, loosen setscrew in upper knife driving o Improperly positioned upper
arm , and turn upper knife shaft to adjust the position from the knife arm shaft will come in
top surface of the throat plate to 34 mm. contact with the frame.
(Caution) Be sure to fully tighten the setscrew since upper knife If it is moved with the position of
shaft is subjected to high load. the upper knife unchanged,
proper engagement of the knives
will be disturbed, prohibiting
sharp cutting of the knives.
1
1) Lower knife o The lower knife, if positioned too
Adjust the vertical position of the lower knife by screw so that the high, will catch materials or
2
blade top aligns with the top surface of the throat plate. cause no contact of the presser
Tighten screw after bringing the upper knife to its lowest position foot with the throat plate top sur-
of its stroke. face.
o If the lower knife is positioned too
1
2) Upper knife low, the cutting width will be
Adjust the position of the upper knife by screw so that the engage- changed or materials will be
ment with the lower knife is 0.5 to 1 mm when the upper knife is in the caught by the lower knife.
lowest position of its stroke. o The upper knife, if positioned too
(Caution) Adjust the lateral position of the lower knife by screw . high, will fail to cut materials.
Adjust the lateral position of the upper knife by screw . o Failure of cutting or abnormal
After performing adjustment, be sure to fix the knife. Oth- wear on the knives will result
erwise, the durability of the knife will be affected. unless the lower knife is laterally
positioned and fixed at a position
1
3) Overedging width where it has settled by itself un-
Adjust the overedging width in the following way : der the upper knife spring.
Laterally position the upper knife before loosening screw .
Tighten screw when the upper knife has settled by itself under the
pressure applied by the spring. Repeat this adjustment procedure to
obtain desired overedging width.
– 27 –
(18) Resharpening of the knife
Standard Adjustment
55°
10°
(19) Position of the thread cam (Applicable only to MO-6716D series)
Standard Adjustment
1) Adjustment of the thread cam
Level
2) Adjusting looper thread cam thread guides A and B and the looper thread cam nail
Level
– 28 –
1) When the knives have become dull, fully resharpen lower knife o If the 10∞ angle of the lower knife
until the contact mark of it disappears. is exceeded, the durability of the
2) When the upper knife has become dull, replace it with a new one. knife will be deteriorated, often
(This is because the upper knife is a serrated carbide knife.) resulting in blade chipping.
o If the angle is smaller than 10°,
the knife will be dull.
o If the 55° angle is not observed,
the knife may catch materials.
1
1) Adjusting the thread cam o If the timing of the thread cam is
Adjust the position of the thread cam by its setscrew with the too early, the needle point will fail
needles at their upper dead point so that the straight section of the to enter a thread triangle,
2
thread cam is leveled. resulting in looper thread stitch
Laterally position the thread cam so that the looper thread cam nail is skipping.
located at the center of the thread cam groove. o If the timing of the thread cam is
too late, puckering and loose
[How to check for proper positioning]
looper thread stitches will results.
Check that the thread cam releases the looper thread when the needle
tip begins to come out of the bottom surface of the throat plate by 0 to 1
mm.
Thread
Throat plate
0 to 1 mm
2) Adjusting the looper thread cam thread guides A and B and the o If the chain looper thread guide
1
looper thread cam nail is moved away from you, the
Install looper thread cam thread guides A and B at the center of take-up amount of the lower
2
the slots with setscrews A and B . looper thread will decrease. In
Install looper thread cam nail with setscrew so that the straight this case, puckering may result
section of the forked portion is leveled. there by impairing the feeling of
the finished product.
– 29 –
(19) Position of the thread cam (Applicable only to MO-6716D series)
Standard Adjustment
3) Adjusting looper thread auxiliary thread take-up lever (Exclusive for 30P)
When lopper thread auxiliary thread take-up lever is in its lower dead point, the thred hole should align
with the hole in lopper thread auxiliary thread take-up lever guide .
The holes should align

with each other at the
lower dead point.
– 30 –
1) Open the cloth base cover and loosen setscrew .

2) When looper thread auxiliary thread take-up lever is in its lower
dead point (when the feed dog goes back to the end), tighten set-
screw so that the thread hole in looper thread auxiliary thread
take-up lever aligns with the thread hole in looper thread auxiliary
thread take-up lever guide .
(Caution) 1. When the feed pitch is changed, perform re-adjustment.
2. Confirm that looper thread auxiliary thread take-up le-
ver does not come in contact with the cloth base
cover.
– 31 –
(20) Adjusting the throat plate support
Standard Adjustment
Uniform contact
(21) Adjusting the feed mechanism cover presser
Standard Adjustment
– 32 –
1) Loosen setscrews and adjust so that throat plate support should o If the throat plate support comes
not come in single-sided contact but come in uniform contact with in single sided contact with the
throat plate using setscrews . throat plate or does not come in
contact with it, the throat plate will
vibrate severely.
1) Loosen setscrew and press feed mechanism cover presser in o If the feed mechanism cover is
the direction of arrow. not fully pressed and the cover
2) Press feed mechanism cover and tighten setscrew so that the rises, oil leakage will be caused.
feed mechanism cover should not rise.
(Caution) Check that feed mechanism cover is pressed so that it
should not rise.
– 33 –
(22) Adjusting the looper cover
Standard Adjustment
o The looper cover should smoothly close without coming in contact with upper knife when slowly closing
looper cover with upper knife in its lowest position of its troke.
Cloth chip
cover
Frame
(23) Adjusting the cloth chip cover
Standard Adjustment
o When cloth chip cover is pressed away from you, it should not rattle.
In addition, the cloth chip cover should not come in contact with upper knife and lower looper .
(There are 2 pcs. inside.)
– 34 –
1) Close looper cover , loosen setscrew , and move looper cover

guide plate back and forth until the looper cover is brought to a
position where the cover smoothly closes.
2) Move looper cover guide plate until it slightly comes in contact
with looper cover receiving bracket . Now, fix the guide plate by
tightening setscrew .
1) Loosen setscrew and temporarily tighten the setscrew with cloth

chip cover stopper raised.
2) Loosen setscrews in the cloth chip cover, and adjust the longitudi-
nal position of cloth chip cover .
3) Loosen setscrew in the cloth chip cover stopper again, and press
cloth chip cover stopper downward until the stopper slightly comes
in contact with looper cover . Now, tighten setscrew .
4) Finally, confirm that cloth chip cover comes in contact with neither
upper knife nor lower looper .
– 35 –
(24) Position of the thread guides and the looper thread take-ups
Standard Adjustment
MO-6704D MO-6714D MO-6716D

Needle thread take-up lever of
B Needle thread guide
2-needle machine
A
A
C
D
Needle thread
P
take-up
B
B Needle thread take-
Needle thread Needle thread guide of
Needle thread take-up guide up lever of double-
guide 2-needle machine
of double-chainstitch ma- chainstitch machine
chine
The thread hole in the needle thread The thread hole in the needle thread The thread hole in the needle thread guide and
guide and the hooked portion of the guide and the hooked portion of the the hooked portion of the needle thread take-up
needle thread take-up are in the posi- needle thread take-up are in the posi- are in the position where 2/3 of the hole in the
tion where 2/3 of the hole in the needle tion where 2/3 of the hole in the needle needle thread guide can be observed.
thread guide can be observed. thread guide can be observed.
The thread hole in the double-chainstitch needle

thread guide and the hooked portion of the needle
thread take-up are in the position where the entire
hole in the needle thread guide can be observed.
(Caution) The needle thread take-up shall be positioned at the lower dead point.
Upper looper thread guide (upper)

E
G K Upper looper thread guide (right)
Upper looper thread guide (middle)
L
Lower looper thread guide
I N
F
H
J
Looper thread t Lower looper thread take-up

Looper thread take-up (left) M
ake-up (right) (Unit : mm)
MO-6 04D MO-6 14D MO-6 16D MO-6 16D MO-6 05D MO-6 04D
Symbol (Standard) (Standard) (Standard) (50H) (Blind-hemming) (Soft chain)
General thread Wooly thread General thread Wooly thread General thread Wooly thread General thread General thread Wooly thread General thread
A 15.8 ← ← ← ← ← ← ← ← 13.5
B 3.4 ← ← ← 1.8 ← 2.6 3.4 ← 2.1
C — — — — 21.5 ← 2.3 — — —
D — — — — 30.5 ← 24.5 — — —
E 22 ← ← ← ← ← ← ← ← ←
F 65 ← ← ← ← ← ← ← ← ←
G 17.5 ← ← ← ← ← ← ← ← ←
H 43.5 ← ← ← ← ← ← 40.5 ← 43.5
I 26.5 ← ← ← ← ← ← 24 ← 26.5
J 38 41 38 ← 34 36 34 38 42 43.5
K 15 ← 12 15 12 15 12 12 ← 14
L 6.5 ← 10 ← 6.5 ← ← 24 34 ←
M 29 ← ← ← 27.5 ← ← 29 ← 26.5
N 27 21 23 ← 20 ← 19 24 ← 19
O 11 ← ← ← ← ← ← 12 ← 9.5
P — — — — 16 ← 12.8 — — —
– 36 –
1) Perform the adjustment by the setscrews. Position of the needle thread o Distance a
guide and needle thread take up lever is a very important decisive When set smaller, better tight-
factor when making soft chains since the needle thread take-up ness of needle thread stitches
amount is increased in this case. So, carefully position these parts. will be obtained.
When set larger, loose needle
thread stitches will result.
Large o Distance E, F and H exert least
Small
a Needle
influence on stitch formation,
however, improper setting of
thread
take-u these distances will cause con-
p amo
unt tact between the moving parts.
o Distance J
When set larger, the amount of
the upper looper thread will be
increased.
When set smaller, the amount of
the upper looper thread will be
decreased.
o Distance K
When set larger, the amount of
2) Set distance I a little smaller when using the upper looper thread will be
synthetic thread or the like which tends to form increased.
stitches swelling out of the cloth edge. When set smaller, the amount of
A smaller I is effective for preventing stitch skip- the upper looper thread will be
ping. decreased.
3) Distance J is related to the vertical knotting point Swell out o Distance L
of the upper and lower looper threads. When set larger, the amount of
Set this distance larger for wooly thread, and set it smaller for thin the upper looper thread will be
thread which is likely to cause stitch skipping. increased.
4) It is desirable to set distance K larger for stretchy threads such as When set smaller, the amount of
wooly thread. the upper looper thread will be
5) Set distance L a little larger when making blind hemming soft chain decreased.
stitches. o Distance N
6) Set distance N a little smaller for blind hemming or making soft chain When set larger, the amount of
stitches. the upper looper thread will be
7) Set distance O larger if stitch skipping occurs due to looper thread increased.
slack. When set smaller, the amount of
Set it smaller for better appearance and touch of produced stitches the upper looper thread will be
when wooly thread is used. decreased.
o Distance I
Upper looper When set larger, the amount of
Thread slack
the upper and lower looper
Lower looper threads will be increased.
When set smaller, the amount of
threads will be decreased.
o Distance O
Needle Thread slack When set larger, the amount of
threads will be decreased.
Upper looper When set smaller, the amount of
threads will be increased.
– 37 –
(25) Adjusting soft chain making mechanism
Standard Adjustment
1) Replacing the parts with those exclusively designed for making soft chains
Needle thread presser plate C ....... 12112504
Driving cam .................................... 12112603
Needle thread presser spring B ..... 12112702 Cam face
Throat plate ....................................(only for 1-needle
overlock machine)
0D4-300 ......................................... R4200J6DD0A
1
2) Adjustment value
Needle thread guide and needle thread take-up lever
Adjust the needle thread guide to increase the needle thread feeding amount when the needle bar is in
the lowest dead point of its stroke.
Needle thread take-up

Max. slot of the needle Max. slot of the needle Needle thread take-
amount when the needle
thread guide thread guide up amount when the
bar is in its lowest dead
needle bar is in its
point
lowest dead point
3.1 to 2.5 to
3.6mm 3mm
(04 1-needle overlock machine) (16 Safely stitch machine)
2 Adjust the rising amount of needle thread presser plate C.

Adjust the rising amount of needle thread presser plate C to 0.6 to 1 mm (max.) by moving driving
cam to the right and left within the slot.
Rising amount : 0.6 to 1 mm (max.)

Cam face
Rising amount
– 38 –
1
3) Important points in adjustment
Increase the thread take-up amount of the needle thread take-up lever.
2
Refer to the adjustment values related to the needle thread guide and needle thread take-up lever.
Reduce the feed of the looper threads. (Mainly lower looper thread)
Set J, K, L and M for the soft chain distances.
3
Fine adjustment of J and M is required to produce even stitches.
Adjsut the thread tension while checking the appearance and touch of the stitches produced.
1) Minimize the needle thread tension as far as satisfactory tightness of needle thread stitches is ob-
tained.
4
2) Increase the upper looper thread tension as much as possible.
If the chain-off thread does not stretch satisfactorily, and if it is not satisfied, proceed with the following.
1) Increase the upper looper thread tension.
2) Further increase distances J and K.
3) Further increase the upper looper thread tension.
4) Increase the lower looper thread tension to a maximum as far as good tightness of needle thread
stitches is maintained.
5) Increase the thread take-up amount. If the needle thread is poorly tensed, increase the needle thread
5
tension.
Fine adjustment for producing stitches with better appearance and touch
1) If the knotting point varies at high or low sewing speed, slightly reduce L, and increase the lower looper
thread tension.
2) If a knot is made at a high point, increase J and I.
3) If the needle thread is likely to break, decrease the thread take-up amount and lower the needle thread
6
tension.
Pay attention to the following
1) Minimize the needle thread tension as far as satisfactory tightness of needle thread stitches is ob-
tained.
2) The knot of upper and lower looper threads should be made near the upper edge of a material.
3) Minimize the lower looper thread tension as far as even stitches are maintained.
4) For a safety stitch machine, adjust the soft chain making mechanism so that uniform chain-off thread
is produced during double-chain stitching and overlocking.
Upper looper thread guide (upper)
E
22 G K
17.5 15 (12) Upper looper thread guide (right)
Upper looper thread
guide (middle)
L
6.5
Lower looper
thread guide
I
5
26.
65
F
N
20) The value given in ( ) parentheses is
27 (
43.5
H
the adjustment value for the safety

(34)
38
J
stitch machine. (Unit : mm)

11
O
Looper thread Looper thread M 5) Lower looper

take-up (left) take-up (right) 27. thread take-up
29 (
Soft chain stitches

When the chain-off
thread is pulled.
Looper thread should not be
loosened and stretch well
Standard stitches
When the chain-off
thread is pulled. The looper thread loosens
– 39 –
4. ADDITIONAL INFORMATION AND PRECAUTIONS
(1) Thread tension
1) Strength of tension spring
Part No. Color Natural length Operating length Weight required to compress
(mm) (mm) spring to working length
13137807 Red 19.5mm 11.5mm 4.21±0.49N (430±50g)
13138508 Yellow 17.8mm 9.8mm 3.14±0.34N(320±35g)
13138805 Blue 17.3mm 9.3mm 1.47±0.20N(150±20g)
2) Springs used for each model.
Where to use Needle thread Double-chainstitch Upper looper Lower looper

Model needle thread thread thread
MO-6704D series Red — Yellow Blue

MO-6714D series Red • Yellow — Blue Yellow
MO-6716D series (30P included) Red Yellow Yellow Blue
MO-6716D- -4 H, -50H Red Red Blue Yellow
(2) Upper looper

Use a proper upper looper in accordance with the needle No. When ordering, refer to the Parts List. The
numbers shown in frame in the table below are engraved markers. In addition, the letters in ( )
parentheses are the kinds of the needles.
Parts Nos. with an asterisk * are factory-installed on the standard machine heads at the time of delivery.
Model Nos. engraved on Needle No.

upper looper (kind)
MO-6704D series *1188 81 #9 #11 #14

MO-6716D series
MO-6714D series *1217 60
– 40 –
(3) Center-to-center distance of the upper looper holder
The center-to-center distance of upper looper holder 1.
(Unit : mm)
Model Center-to-center
distance H
MO-6704D - -
MO-6705D - - 0 38
MO-6704D - 0E4 40H

- 39
0F6 50H
MO-6712D -D - 39
MO-6714D - - 39
H
MO-6716D - - 0 38
4 H
MO-6716D -DE to FF -5 H 39
MO-6743D - - 40H 39
(4) Caution in assembly

1) Application of sealant
1 Setscrew of the throat plate base (B) retainer (JUKI seal)
Apply the sealant only to the right setscrew.
Frame
Apply only to the right setscrew
2 Bottom surface of the upper looper guide support (Three-bond 1104)

Apply the sealant to the bottom surface of the upper looper guide support , which contacts with the
frame surface.
3 After assembling the front edge of the upper looper guide support (JUKI seal), apply the sealant to
the gap of the contact surface between the frame and the upper looper guide support ( section
in the illustration).
Be careful not to allow the

sealant to run to the rear.
Apply the sealant to the

bottom surface.
bottom surface.
– 41 –
4 Portion of the setscrews of the dust-proof rubber case (JUKI seal)
Apply the sealant to the oil shield case setscrew (1 pc.) and the dust-proof rubber case setscrews
(4 pcs.)
5 Oil shield plate assembly (JUKI seal)

Apply the sealant to the inside of the oil shield plate .
Apply the sealant to

the hatched parts.
Inside contact surface
6 Portion of the feed mechanism cover (Three-bond 1212)

Apply the sealant to the rear face of the feed mechanism cover, the top surface of the oil shield plate,
the oil shield rubber support plate , the top surface of the oil shield case, and the hatched parts on the
top surface of the feed bar presser.
Apply the sealant to the frame.
Feed mechanism
cover (rear face)

top surface of the oil
shield plate.
Lightly apply the sealant to the rear

Apply the sealant to the oil shield rubber support face of the feed mechanism cover
plate and the top surface of the oil shield case. and the top surface of the feed bar
Be careful that the sealant should not overflow on presser.
the side of the oil shield rubber.
7 Various sealants
Maker’s name Part No.
Three Bond 1104D * * : It is commonly called “JUKI seal”.
Three Bond 1104

Three Bond 1212
JUKI exclusive part Nos. of the above 3 kinds of the sealants are not set.
– 42 –
2) Precautions to be taken with respect to the lubricating components
1 Feed bar components
o Be careful of the orientation of the oil shield rubber and the dust-proof rubber .
* Assembling as shown in the illustration

will result in oil leakage. So, be careful.
o Assemble the feed bar presser and the dust-

proof rubber case so that their top faces are
flush with the frame plane on which the feed
mechanism cover is installed.
o Do not loosen the screws in feed bar presser
unless it is necessary. The clearance between
the feed bar presser and the feed bar and the
contact with each other are important.
Do not loosen the screws.
2 Portion converted to dry-head type

Forced lubrication room
1. Needle bar mechanism portion
[Wet portion]
[Dry portion]
2. Feed mechanism portion

[Wet portion]
3. Upper looper mechanism portion

[Dry portion]
– 43 –
3) Applying the exclusive grease
o The exclusive grease (23640204) is applied to the necessary components other than the lubricating com-
ponents. Never use any grease other than the exclusive one.
It is not necessary to additionally apply grease to the components when the sewing machine is used under
the normal condition.
When the machine is used under the specially severe condition, it is effective to periodically (once a year
or every other year) fill up the exclusive grease.
* : Apply the exclusive grease.
1 Needle bar components
*
*
*
* (Caution) There are grease grooves on the inside
of needle bar upper metal (No. 19) and
needle bar lower metal (No. 18). Fill up
the exclusive grease to the groove por-
tion when drawing out the needle bar.
– 44 –
2 Upper looper components
*
*
* *
* *
*
– 45 –
(5) Kinds of motor pulleys, belts and frame support plate bolts
1) Motor pulleys and belts
Sewing 50Hz 60Hz

speed of Outside diameter V-belt Outside diameter V-belt
sewing of motor pulley mm of motor pulley mm
machine (effective diameter Semi-sunken type Fully-sunken type (effective diameter Semi-sunken type Fully-sunken type
(rpm) mm) mm (inch) mm (inch) mm) mm (inch) mm (inch)
6000 110 (105) 914 (36) 813 (32) 95 (90) 889 (35) 762 (30)
5500 100 (95) 914 (36) 813 (32) 85 (80) 889 (35) 762 (30)
5000 90 (85) 889 (35) 762 (30) 80 (75) 864 (34) 762 (30)
4500 85 (80) 889 (35) 762 (30) 70 (65) 864 (34) 762 (30)
4000 75 (70) 864 (34) 762 (30) 60 (55) 864 (34) 737 (29)
* A motor with 1/2 horsepower (400 W) or more shall be used.

(Caution) If a motor of less than 400W is used, in the low temperature area, viscosity of oil increases
and the sewing speed may not increase or the sewing machine may fail to run in some cases.
* Part No. of motor pulley

MTKP0xxx000 (Enter the effective diameter to “xxx.”)
If the outside diameter of the motor pulley is 90 mm, the effective pulley will be 085.
.....So, the part No. will be MTKP0085000.
* Part No. of belt
MTJVM00xx00 (Enter a number that shows the belt length to “xx”)
If the belt length is 889 mm (35 inches), enter “35” to “xx.”
.....So, the part No. will be MTJVM003500.
2) Pat No. of frame support plate bolt

1 Semi-sunken type
Support plate bolt (A) 13155007 x4
Locknut NS6240630SE x4
Washer WP1002036SE x4
Spring washer WS1002560KR x4
2 Fully-sunken type
Support plate bolt (C) 13155106 x2
Support plate bolt (D) 13155205 x2
Locknut NS6240630SE x 12
Washer WP1002036SE x 12
Spring washer WS1002560KR x4
Difference of support plate bolts (A), (C) and (D)

Entire length under the neck and length of threaded part
Support plate bolt (A) Support plate bolt (C) Support plate bolt (D)
Entire length Length of threaded part
(mm) (mm)
Support plate bolt (A) 69 39
69mm
Support plate bolt (C) 137 107

137mm
39mm
107mm
149mm
Support plate bolt (D) 149 119

119mm
– 46 –
5. ADJUSTMENT VALUES OF THE NEEDLE HEIGHT AND LOOPER TIMING
(1) MO-6700D SERIES
(Unit : mm)
Needle height Upper looper components Lower looper components Double-chain looper
Classification
Description
1- needle overlock 1-needle 2-needle Upper looper Projection of Upper looper Marker of Position of Guide support Center-to- Marker of Feed amount Radius of Feed amount Radius of
Needle height
macine/safety 2- needle overlock 3- needle

stitch machine macine safety stitch 2-needle (right) height upper looper holder height guide support guide support cover center of upper upper looper of lower lower looer of double- double-chain
(left) of pin looper holder holder chain looper looper
Subclass A B C D E F G H J K L M
A B C B C
0A5 to 0F5 15 7
1-needle overlock machine

6704D 40004713 #81 +0.5
MO- - 0A4 to 0E4 - 210 10.5±0.1 — 11.0±0.3 4.0±0.3 (45.0) A 38 4.0 –0.8 66.9 — —
6705D 0D6 3 Marker A (11888609)
6.3
40004713 #81
MO-6704D - 0F4 - 30 10.5±0.1 — 11.0±0.3 4.0±0.3 (46.2) A 38
+0.5
3.7 –0.7 66.9 — —
A (11888609)
E E
0D4 to 0E4 5.8 40004713 #19 +0.5
MO- 6704D - 0F6 -4 H 11.3±0.1 — 11.3±0.3 4.4±0.3 (48.2) A 39 3.8 –0.8 66.9 — —
Upper looper components
50H A (11991908)
D
D G 6 #60
40004714 +0.5
2- needle overlock MO- 6714D - BD6 to BE6 - 7 10.5±0.1 (9.1) 10.3±0.3 4.4±0.3 (47.3) B 39 (12176004) 3.8 –0.8 66.9 — —
macine B
2-needle overlock machine
3- needle
safety stitch 6
40004714 #60 +0.5
MO-6714D - B 6 - 30P 10.5±0.1 (9.1) 10.3±0.5 4.4±0.3 (47.3) B 39 3.8 –0.8 66.9 — —
B (12176004)
F H
5.8 40004713 #61 +0.5
MO- 6714D - BD to BE - H 11.3±0.1 (9.9) 11.0±0.5 4.8±0.3 (48.4) A 39 3.8 –0.8 66.9 — —
A (12176103)
5.5 #66
3.6±0.3 40004714
MO- 6712D - DF6 - 50F 11.0±0.3 (9.4) 11.0±0.5 (46.9) B 39 (11996600) 2.2±0.3 66.9 — —
(Right side) B
6.3
40004713 #81 +0.5
J MO- 6716D - - 30 10.5±0.1 — 11.0±0.3 4.0±0.3 (46.2) A 38 3.7 –0.7 66.9 1.5 to 2.0 63.4
A (11888609)
Lower looper components
J
Safety stitch machine
5.8
40004713 #19 +0.5
MO- 6716D - D to F -4 H 1.3±0.1 — 11.3±0.3 4.4±0.3 (48.2) A 39 3.8 –0.8 66.9 1.5 to 2.0 63.4
50H A (11991908)
K
5.8
1D6 40004713 #61 +0.5
MO- 6743D - 2D6 - 40H 11.3±0.1 (9.9) 11.0±0.3 4.8±0.3 (48.4) A 39 3.8 –0.8 66.9 1.5 to 2.0 63.4
2- needle overlock A (12176103)
macine
3- needle
safety stitch
MO- 6745D - FF4 - 360 9.8±0.1 — — — — — — — — — — — 2.0 to 2.5 63.6
L
Double-chain looper components
M
13131909 13132006 13131008 13131107
7 5.5 6.3 4.7
Upper looper
guide support Upper looper
gauge holder
6
5.8
38 39
– 47 –
6. TROUBLES AND CORRECTIVE MEASURES
Trouble Case (1) Case (2) Check and Corrective measures Page
1. Needle thread breakage Threading The thread is entangled with the thread Refer to the threading diagram.
guide, or the machine head has been (Refer to the Instruction Manual)
incorrectly threaded.
Thread path Scratches, burrs or rust on the pawls Remove such scratches, burrs, etc. and
or needle holes of the throat plate, perform thread path finishing. Replace major
stitch tongue, lower looper, double chain components such as looper, which have
looper, needle thread take-up, needle been deformed, causing thread breakage.
thread presser spring, thread guide,
or tension discs causes friction.
Needle guard The needle hits the needle guard intensely, Replace the needle and needle guard if 18
and sharp edges are produced on them, they have worn,
causing thread breakage.
Needle The needle is too thin for the thread. Replace the needle by a proper one.
– 48 –
Needle heat The needle gets very hot, depending on Use a thinner needle. Reduce the sewing
the type of materials, number of plies and speed. Use the needle cooler. Use an S-point
sewing speed, and causes the thread to needle or needle for synthetic thread.
burn and break.
Thread The thread is weak because of its poor quality. Replace the thread by one with good quality.
Thread tension The thread tension is too high. Reduce the thread tension. Check whether the
needle thread take-up guide and needle thread
guide are positioned too high, causing such
excessive thread tension.
Contact The double chain looper or lower looper Properly position the double chain looper or 8, 16
has been improperly positioned and strikes lower looper.
the feed dog or throat plate.
Double thread hooking Poor drawing up of the needle thread Increase the needle thread tension. Properly 28
(only for double chain stitch) causes the looper to catch it again. position the thread cam. Properly position the
double chainstitch thread guide.
Defective double chain-off thread Refer to the clause referring to defective

(only for double chain stitch) double chain-off thread.
2. Looper thread breakage Thread path Scratches, burrs, rust, etc, on the paw of Remove such scratches, burrs, etc. and carry
the throat plate, stitch tongue, looper, out thread path finishing. Replace loopers or
looper thread take-up, thread guide, other components which have been deformed,
or tension discs causes friction. causing thread breakage.
Adjustment of the looper thread take-up The looper thread take-up or thread guide Refer to the pertinent Standard Adjustment. 36
has been improperly positioned, causing
excessive thread tension.
Thread tension The looper thread tension is too high. Reduce the tension while checking the tension
balance other looper thread.
Thread The thread is weak because of its poor Replace the thread by one with good quality.
quality.
Position of the thread guides The upper looper thread guide is too high, Refer to the pertinent Standard Adjustment. 36
(only for double chain stitch) and the thread taking balance is disturbed,
resulting in the thread breakage.
– 49 –
Double chain looper avoid The double chain looper strikes the needle Correct the longitudinal motion of the double 16
at the back, causing the thread breakage. chain looper so as not to cause the looper to
strike the needle.
Needle heat The needle gets hot, and the looper thread Refer to the clause relating to the needle heat
breaks when it comes in contact with the causing needle thread breakage.
hot needle at the time of needle stop.
3. Needle breakage Needle entry The needle entry has not been correctly Correct the needle entry. 4
adjusted, and the needle strikes the throat
plate or presser foot.
Upper looper position The upper looper juts out too much or Refer to the related Standard Adjustment. 14
it is too low.
Contact with the looper The needle strikes the looper, resulting Re-position the looper so that it does not come
in needle breakage. in contact with the needle. Adjust the longitudinal
motion of the double chain looper for the contact
of its back with the needle.
▼
to the next page
From the previous page
Needle guards A needle guard has been improperly Refer to the pertinent Standard Adjustment. 18
positioned, causing the needle point to
strike it.
Needle No. The needle is too thin for the materials. Replace the needle with a thicker one.
Thread tension The thread tension is too high. Reduce the thread tension.
Height of the feed dog or needle The feed dog is too high, or the needle is Refer to the related Standard Adjustment. 4, 20
too low, causing the needle to deflect with
resultant needle breakage.
4. The needle point is crushed. Needle guard The needle guard C is too low, or its Increase the height of the needle guard (C). 18
(Double chain stitch needle) longitudinal position is not correct. Check the clearance between the needle and
needle guard.
Contact with the looper The tilt of the looper is not correct. The Check the tilt of the looper. Correct the longitudinal 16
longitudinal motion of the looper is not motion of the looper, and increase the clearance
– 50 –
correct. between the looper and needle when the

looper reaches its most retracted position.
5. Overlocking needle thread stitches Lower looper The blade point has defective shape and Replace the lower looper.
are skipped. does not catch needle thread loops.
Adjustment of the loopers. The clearance or the amount of return is Refer to the relevant Standard Adjustment. 8
The lower looper fails to catch not correct.
needle thread loops.
Needle thread presser The duration in which the presser holds the Refer to the pertinent Standard Adjustment.
needle thread is not correct, and unstable
Right side Wrong side
loop result.
Needle The needle is bent or improperly oriented. Replace the bent needle. Correctly orient and
A needle or DC x 1 is used. attach the needle.
Use a DC x J27 needle for a stretchy thread.
Needle guards Incorrect height or clearance prohibits Refer to the pertinent Standard Adjustment. 18
correct guide for the needle. If a needle
guard is too high, loops are crushed with
consequent stitch skipping.
▼
to the next page
Height of needle The needle has incorrect height and does Refer to the related Standard Adjustment. 4, 8
not properly pick up loops even if the looper
has a correct return.
Needle heat Stitch skipping occurs before the thread Refer to the clause relating to the needle thread
breaks due to needle heat. breakage due to needle heat.
Positioning of the needle thread take-up They are positioned too high, and the Refer to the pertinent Standard Adjustment. 36
guide and needle thread guide needle thread take-up takes too much
thread, producing too small loops.
Threading The thread has been entangled with a See the threading diagram.
thread guide. (Refer to the Instruction Manual)
The reading has bot been correctly done.
6. Lower looper stitches are skipped Threading The thread has been entangled with a Refer to the threading diagram.
– 51 –
Threading has not been done correctly.

The upper looper does not catch
the lower looper thread. Upper looper The blade point has a bad shape, and Replace the upper looper with badly
fails to catch the loops. deformed blade point.
Lower looper The clearance between the needle and Replace the lower looper having a deformed
Right side Wrong side the back of lower looper are not correct. tip.
Adjustment of the loopers The feed amount of the lower looper, height Refer to the relevant Standard Adjustment. 8, 14
of the upper looper, or clearance produced
at time of crossing of the upper and lower
oopers is not correct.
Thread amount Too much lower looper thread is fed, Slightly lower the looper thread take-up (left) 36
giving slack of thread. (reduction in distance J), or slightly reduce
distance I to decrease the amount of thread.
Slightly raise the looper thread take-up (right) 36

(increase in dimension O) to decrease the
amount of thread. Lower the lower looper
thread guide (increase in distance L), and
decrease distance N to reduce the amount of
thread.
7. Upper looer thread stitches are skipped. Threading The thread has been entangled with a See the threading diagram.
Threading has not been done correctly.
The needle does not take the
upper looper thread.
Needle height The needle, if positioned too high or low, Refer to the related Standard Adjustment 4
may fail to catch the upper looper thread.
Needle The needle is bent or crushed, in its point. Replace the needle. At this time, be sure to
Right side Wrong side
eliminate the cause for such needle bend or
needle point crush.
Lower
looper
Needle Adjustment of the upper looper. The height of the blade point is not correct, Refer to the relevant Standard Adjustment. 4, 14
thread
making the upper looper unable to properly
pass the thread to the needle.
Upper looper The clearance between the needle and the
back of the upper looper is not correct.
Amount of thread Excessive upper looper thread is fed, Slightly lower the looper thread take-up (left) 36
producing stack of thread. (reduction in distance J), or slightly reduce
distance I to decrease the amount of thread.
– 52 –
Needle Make the upper looper thread guide (right)

Slack of thread
(shorter decrease in distance K), to reduce the
amount of thread.
Slightly raise the looper thread take-up (right) 36

(increase in dimension O) to decrease the
amount of thread.
If the thread tension is not enough, increase it.
8. Double chain stitches are skipped. Needle height If the needle is not correct, stitch skipping Refer to the pertinent Standard Adjustment.
occurs even when the return of the chain
looper is correct.
The double chain looper tails to
catch needle thread loops. Needle The needle is bent or attached with wrong Replace the bent needle. (Remove the cause
orientation. A DC x1 needle is used. for the needle bend.) Correct the orientation of
the needle. Use a DC x27 needle (with a better
Viewed from the
recess configuration).
wrong side
Double chain looper The lower part of the blade point has been Replace the double chain looper.
deformed, and the blade point fells loops.
Two stitches
are skipped. ▼
to the next page
Adjustment of looper Clearance or returning amount is not correct. Refer to the related Standard Adjustment. 6
Thread tension The thread tension is too high, preventing Reduce the tension. However, be careful not
formation of good loops. to reduce the tension too much, otherwise
unstable loops will result.
Needle guards A needle guard is too high, and loops are Refer to the relevant Standard Adjustment. 18
crushed. The clearance is too big, causing
the needle to shake.
Needle heat The thread breaks due to heat generated Use a thinner needle. Reduce the sewing speed.
on the needle, depending on the type of Check the coolant if necessary.
materials, number of plies, and sewing
speed.
9. Triangle double chain looper thread The needle point is crushed. The needle point has been crushed and Refer to the clause relating to the needle point
stitches are skipped. got thicker and shorter. crush.
– 53 –
The needle fails to catch the Double chain looper The thread hole in the tip has worn, and Replace the double chain looper.
double chain looper thread. the looper thread does not reach the
needle as shown at right.
Needl
Viewed from the
wrong side Adjustment of looper Excessive return or longitudinal motion Refer to the pertinent Standard Adjustment. 16
will often cause this stitch skipping.
Thread cam timing The thread cam timing is too early, causing Refer to the pertinent Standard Adjustment. 28
the looper thread to slack before the needle
One stitch is skipped. enters a thread triangle.
Thread tension The lower thread tension is very low, and Increase the thread tension a little.
the thread is not stretched.
Threading he area around the thread cam has Correct the threading.
threaded erroneously.
10. Triangle double chain needle Double chain looper The chain looper is too high and too close Correct the height of the chain looper by 16
thread stitches are skipped. to the throat plate, or has bad shape. pushing it down until it cones into contact
with the stopper. Replace the chain looper
having a bad shape.
The needle fails to catch the
needle thread loop on the double
Adjustment of looper The return is not enough, causing the Refer to the related Standard Adjustment. 16
chain looper, resulting in the stitch
needle to miss the loop.
skipping shown below.
Thread tension The needle thread tension is too low. Slightly increase the needle thread tension.
Stitch length The stitch length is as small as 1.5 mm Slightly increase the stitch length.
or less.
Defectively interlaced loop Adjustment of loopers for producing chain-off 28
Needle thread thread without materials requires higher
accuracy than that with materials.
Needle guard A needle guard is too high, and catches Refer to the related Standard Adjustment. 18
needle thread loops.
The needle thread extends
to the adjacent stitch.
Double-chain stitch needle thread The needle thread guide is installed too Refer to the related Standard Adjustment. 36
– 54 –
guide. high, and it fails to tense the thread.
11. Overlocking chain-off thread is bad. Position of the throat plate The throat plate has been improperly Correctly position the throat plate.
positioned longitudinally, and chain-off
Provided that no chain-off trouble oc- thread gets in between the main feed dog
curred when sewing operation was and throat plate, causing defective chain-off
done with materials set on the machine. thread.
Feed dog The auxiliary feed dog has scratch. Repair or replace the auxiliary feed dog. 20
The auxiliary feed dog is too high, and Refer to the pertinent Standard Adjustment.
interferes with chain-off thread. The auxiliary
feed dog is too low.
(Lower than the main feed dog by more
than 0.5 mm)
Adjustment of looper Adjustment of loopers for producing Refer to the related Standard Adjustment. 8
chain-off thread without materials requires
higher accuracy.
Thread tension The thread tension is too low. Slightly increase the tension.
The needle thread tension is too high, Check whether the needle thread take-up 36
causing damaged balance with other guide or needle thread guide is positioned
thread tension. too high with consequent excessive needle
hread tension. And if so, correct it.
12. Problems with double chain stitch Adjustment of loopers Adjustment of the loopers for producing Refer to the related Standard Adjustment. 16
chain-off thread. chain-off thread without materials requires
higher accuracy.
Needle Guard The needle guard (C) is too high, Refer to the related Standard Adjustment. 18
damaging loops.
Position of the throat plate The needle comes into contact with the front Correctly position the throat plate.
edge of the needle hole in the throat plate.
The lateral position of the throat plate with

respect to the feed dogs is wrong, causing
chain-off to drop in.
Throat plate A dent exists on the flat part between the Repair or replace the throat plate, since such
rear edge of the needle hole and feed dog dent causes chain-off thread to slip out.
groove.
– 55 –
Dent
Presser foot The rear pressure foot is indented and not Replace it, or correct it to make it flush with
flush with the presser foot sole, so that it the presser foot sole.
cannot hold chain-off thread.
Main feed dog The leading edge of the main feed dog is Buff the leading edge of the main feed dog.
too sharp and cuts chain-off thread.
Double hooking The needle thread is not drawn up fully Refer to the related Standard Adjustment for 16, 28
because of the insufficient return of the the return of the double chain looper. See the
double chain looper or wrong threading. threading diagram for correct threading.
If the feed pitch is too small, the cam Retard the cam timing.
timing will be advanced.
Thread tension The needle is bend or chain-odd thread Reduce the needle thread tension.
runs back due to excessive needle thread
tension.
Both the needle thread and looper thread Slightly increase the both tensions.
tension are too low.
13. Overlocking needle thread is loose. Position of the needle thread take-up They are positioned too high, and the thread Refer to the pertinent Standard Adjustment. 36
guide and needle thread guide take-up draws out excessive needle thread.
Thread tension The thread tension balance has been Refer to the Standard Adjustment for the looper
disturbed. thread take-up components, and increase the
tension if necessary.
Needle The needle is too thin for the thread used. Replace it with a proper one.
14. Double chain stitch needle thread Thread tension The looper thread tension is too high, and Reduce the looper thread tension to a minimum,
is loose. the needle thread tension is too low. and increase the needle thread tension.
Thread cam The thread cam draws out an insufficient Refer to the relevant Standard Adjustment. 28
amount of thread.
The thread cam timing is bad. Refer to the relevant Standard Adjustment. 28
Needle The needle is too thin for the thread used. Replace the needle with a proper one.
– 56 –
Double-chain stitch needle thread Drawing amount of the needle thread is Refer to the relevant Standard Adjustment. 36
take-up guide insufficient.
15. Uneven overlocking stitches Looper thread tension The upper and lower looper thread tensions Slightly increase the upper and lower looper
are not enough. thread tensions.
The knotting position of the upper Looper thread take-up The looper thread take-up (left) is too high. Slightly lower the looper thread take-up (left) 36
and lower looper threads varies
as shown below.
Knife width The knife width is unsuited for the Make the overedging width slightly smaller than 26
overedging width. that given for the knife width.
Thread path Scratches on the thread path catch thread. Check the thread path for scratches.
Presser foot The presser foot cones into contact unevenly Make the presser foot come into contact with
with the throat plate and feed dogs and tends them evenly.
to meander.
Thread stand Thread dose not come out smoothly. Make the thread come out smoothly.
16. Uneven double chain stitches Thread tension The looper thread tension is not enough. Slightly increase the tension.
Presser foot The presser foot comes into contact with Make the presser foot come into contact with
the throat plate unevenly. the throat plate evenly.
The presser foot pressure is not enough. Increase the presser foot pressure.
17. The looper thread bulges out Knife width The knife width is too small for the Use a knife having width suited to the
overedging width. overedging width.
Looper thread take-up adjustment The looper thread take-up draws out Decrease the radius of the looper thread take-up 36
excessive looper thread. (left) (reduction in dimension I). Raise the looper
thread take-up (right) (increase in distance O).
18. Looper thread bite Knife width The knife width is too large for the Use a knife having width suited to the
overedging width. overedging width.
Adjustment of the looper thread take-up The looper thread take-up draws out Increase the radius of the looper thread take-up 36
– 57 –
insufficient amount of looper thread. (left) (increase dimension I). Lower the looper
thread take-up (right) (reduction in distance O).
19. Knotting position is not correct. Threading Re-threading after thread breakage,etc. See the threading diagram.
has been done erroneously. (Refer to the Instruction Manual)
Right side Adjustment of the looper thread take-up The height of the looper thread take-up Raise the looper thread take-up (left) to increase 36
Knots are deflected to (left) is not correct. the amount of upper looper thread, and the
the upper looper side. knotting position moves toward the lower looper
side.
The upper looper thread guide (right) is Increase distance K.

too short.
20. Uneven material feed Presser foot pressure The presser foot pressure is too high. Reduce the presser foot pressure except for
the uneven material feed due to puckering.
Presser foot The hinge is too stiff. Remove the stiffness provided no hinge play
is produced.
Scratches on or defective finish on the Buff the presser foot sole for good surface
presserfoot sole produce friction between finish.
the presser foot and materials.
Tilt of feed dogs The front is too high. Make the front down. However, be sure to align
the differential feed dog with the main feed dog.
Height of feed dogs A different in level exists between the main Eliminate the difference in level.
feed dog and differential feed dog.
Adjustment of differential feed The differential feed has been improperly Provide differential feed suited to the material.
adjusted.
– 58 –
21. Puckering Needle The needle is too thick. Use a thin needle as much as possible.
(Mainly concerned with double chain Thread The thread used is too thick. Use a thin needle as much as possible.
stitch)
Thread tension Both the needle thread and looper thread Reduce the both thread tensions to a minimum.
tensions are too high.
Throat plate The throat plate has a large needle hole. Replace the throat plate with one with a small
needle hole.
Thread cam timing The thread cam timing is too late Advance the cam timing. Refer to the related
Standard Adjustment.
Feed dogs The leading edge of the feed dog teeth Replace the feed dog.
has been rounded off.
A difference in level exists between the Eliminate such difference in level.

main feed dog and differential feed dog.
▼
to the next page
Presser foot pressure The presser foot pressure is not high Increase the presser foot pressure.
enough, providing poor ironing effect.
Differential feed ratio The differential feed ratio has been set for Set it for stretching. When stretching light-weight
gathering. materials, be careful not to cause the presser
foot to contact unevenly with the materials.
Thread amount The looper thread amount is not enough, Bring the thread cam thread guide fully to the
causing excessively tensed stitches. front to increase the amount of looper thread.
– 59 –
7. DIMENSIONS OF TABLE
(1) Semi-sunken type
1200
Applicable models
130 MO-6000 Series
75
R3
0
0
R3
60
159±1 54±1
3-8.5 hole, with 26 x 1 deep groove
66.5±1
5
R1 Drilled hole 17
100 Drawer stopper installing Y Y
position (Rear)
30
297
291±1 339
5
46 R1
4-10 hole, with 26 x 1
deep groove R1
40
5
R1
R1
R1
5
5
272±1
R1
25
(380)
0
11
0
49 445
R1
Z Z
570
219±1
113±1
14 577±1
28±1
446
Drawer installing
450
position This plane is finished
in the method same as
42±1
390
the outside wood.
R1
R1 (26)
5
5 R1
R1
5
W W
0
125±1 401
210
37.5
60
R2
Leg installing position
R5
4
5
64
R1
R3
V 25
203.5
5
0
R1
R1
Push button switch
R1
158
5 5 installing position
R1
124
120
116
20
84
57
10
10
R2
40
R3
R6
40
15
R6
0
21 50 125 40
R30
(806) 20
130
JUKI logotype 500 500
600
Top of table
2
R2
40
2
R2
R
Detail drawing of measure (2:1) Type : Helvetica Reg. Condensed R15

11
Condensed voided letters
0.8 1 1 0.8 (ø26) (ø26) This plane is finished
Thickness : 1.5 the outside wood. 37.5
0.5
1 30˚ 30˚
5-R
1
1
7.5
7.5
11.5
R2
R2
R2
10
R2
15
20
7
(ø10) (ø8.5)
120˚ 5x160=800 Section Y-Y Section V-V

Section W-W Section Z-Z
Thickness : 0.8
Thickness : 0.5
Thickness : 1.5 (Note) All dimensions are in millimeter.

Detailed dimensions of section W-W, section Z-Z, section Y-Y and section V-V Part No. of table : 11959400
– 60 –
(2) Semi-sunken type (synchronizer is used)
1200
130
Applicable models
75 MO-6000 Series
R3
0
R3
0
60
159±1 54±1
Drilled hole 17
66.5±1
5
Y Y R1
100 Drawer stopper installing
position (Rear) 30
36 hole 297
339
5
48 291±1 R1
4-10 hoke 26 spot R1
R1 5
40
face 3.5 deep
5
5
R1
R1
5
R1
11
272±1
R1
5
15
25
0
10
0
60 35
(380)
R1
Z Z
49 445
113±1
450
14 577±1
570
0 204
R1
219±1
281±1
This plane is finished
446
Drawer installing in the method same as
42±1 5
position the outside wood. R1
390
R1
R1
60
5
5 R1
R1
5
125±1 401
0
210
60
(37.5)
R2
W W
R5
4
V V
203.5
64
R3
R1
25
5
R1
R1
Push button switch
5 R1 installing position
R1
154
5
120
116
138
20
57
84
R3
R2
R6
40
0
10
10
R6
R30
15
40
125 40
21 50
20
(806) 130
500 500
JUKI logotype
600
Top of table
2
R2
40
2
R2
R
Type : Helvetica Reg. Condensed R15

11 Detail drawing of measure (2:1) Condensed voided letters
0.8 1 1 0.8 (ø26) (ø26) This plane is finished
the outside wood. 37.5
Thickness : 1.5 30˚
0.5
1
(3.5)
5-R
1
7.5
7.5
R2
11.5
R2
R2
10
R2
15
20 (ø8.5)
7
(ø10)
120˚ 5x160=800
Section W-W Section Z-Z Section Y-Y Section V-V
Thickness : 0.8
Thickness : 0.5
(Note) All dimensions are in millimeter.
Thickness : 1.5
Part No. of table : 11959707
– 61 –
(3) Fully-sunken type
1200 Applicable models

75 MO-6000 Series
R3 Drilled hole 17 0
0 R3
60
159±1 54±1
Drawer stopper installing

350
position (Rear)
Y
66.51
Y
277
R1
4-10 hoke 26 spot face 4 deep
5
15
6
R
R15
30 252
R1
R1
R3
40
0
0
R2
R4
8
R10
(380)
201
X X 10
113±1
R
570
0
Drawer installing 150 400±1 R3 184
position
319
446
425
281±1
160
223±1
337±1
385
400
369
Z Z
375
160
437±1 42±1
R3
(426) 0 308

107
203.5
R1
0
4
R16
R3
103
Push button switch
120
R1
110 installing position
0
93
24
84
46
0
R6
R6
R2
R3
R3
50
10
40
34
24
0
290
125 40
20
(806)
150
Concealed hinge Clamp Top of table

Location of silk screening on the table surface
15
2.5
R2
R2
14
40
R2
R
2
50 78
Brand label location indicating of drawing 3 Screw Lid support plate
7
(14)
Section Z-Z Section Y-Y Section X-X

2
(ø26) ø26
9 30˚
JUKI logotype
(4)
(1)
(silk screening)
2
R
15
(Note) All dimensions are in millimeter.

18 (ø10)
(ø8.5) Part No. of table : 11959558
– 62 –
1
The environmental management system to promote and conduct
the technological and technical research, the development and
design of the products in which the environmental impact is consid-
2
ered,
the conservation of the energy and resources, and the recycling, in
the research, development, design, distribution, sale and mainte-
nance service of the industrial sewing machines, household sew-
ing machines and industrial-use robots, etc. and in the sale and
maintenance service of data entry system and in the purchase, dis-
tribution and sale of the household commodities including the
This manual uses environment-friendly soyink. healthcare products.
MARKETING & SALES H.Q.

8-2-1, KOKURYO-CHO,
CHOFU-SHI, TOKYO 182-8655, JAPAN
PHONE : (81)3-3480-2357 • 2358
FAX : (81)3-3430-4909 • 4914
Please do not hesitate to contact our distributors or agents in your area for further information when necessary.
* The description covered in this engineer's manual is subject to change for improvement of the
Copyright © 2005 JUKI CORPORATION. commodity without notice.
All rights reserved throughout the world. 05 · 06 Printed in Japan (E)

MO 6700D+SeriesEM00 e

Uploaded by

Copyright:

Available Formats

MO 6700D+SeriesEM00 e

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MO 6700D+SeriesEM00 e

Uploaded by

Copyright:

Available Formats

®

HIGH SPEED SEMI-DRY HEAD OVERLOCK/INTERLOCK/

2. MODEL NUMBERING SYSTEM .................................................................... 2

3. STANDARD ADJUSTMENT .......................................................................... 4

4. ADDITIONAL INFORMATION AND PRECAUTIONS .................................. 40

5. ADJUSTMENT VALUES OF THE NEEDLE HEIGHT

6. TROUBLES AND CORRECTIVE MEASURES ........................................... 48

7. DIMENSIONS OF TABLE ............................................................................ 60

No. Item Specifications

1 Model MO-6704D MO-6714D MO-6716D

2 Description 1-needle Overlock 2-needle Overlock 2-needle Safety stitch

4 Sewing speed 6000rpm

3 to 6 Model classification 7 Type classification

8 Needle gauge classification 9 Overedging width classification 10 Feed dog classification

The asterisk (*) indicates 3-needle type.

15 to 22 Device and attachment classfication

24 Place of destination 25 Accessories type

MO-6704D-0 -300 10.5 — —

MO-6714D-B - 7 10.5 9.1 —

MO-6714D-B - H 11.3 9.9 —

MO-6716D-FF6-307 10.5 — 9.8

(2) Positioning the throat plate

Needle driving shaft

o Improper lateral position of the

Adjustment Procedure Results of Improper Adjustment

Butt the needle clamp with the

The center-to-center distance should be 26 mm.

Adjustment Procedure Results of Improper Adjustment

1) Returning amount of the lower looper

2) Clearance between the lower looper and the needle

o Excessive return of the lower

Vertical position : To be in close contact with the frame guide surface.

Upper looper guide

Marker dot 13131909 13132006

Frame guide surface

(Unit : mm) (Unit : mm)

MO- 6716D - - 30P

MO- 6714D - BB6 to BE6 - 30P

Bottom surface of frame MO- 6714D - BB6 to BE6 - 30P 47.3

MO- 6716D - - 30P 46.2

MO- 6716D - D -4 H 48.2

1) Height of the upper looper

D MO-6704D-0A -150 11.0 4.0

MO-6714D-B - 7 10.3 4.4

MO-6714D-B - H 10.5 4.8

MO-6716D-FF6-307 10.3 4.4

2) Longitudinal position of the upper looper

1) Returning amount of the double chain looper

2) Longitudinal motion (Avoid motion)

3) Clearance between the double chain looper and the needle

o Excessive return of the double

o Insufficient avoid motion will

1) For 1-needle or 2-needle overlock machine

Needle guard A Needle guard B

2) For safely stitch machine

MO-67 D- -30P 0.8

(12) Adjusting the tilt of the feed dog

MO-6700D series (30P excluded) 1.0 (1.2)

MO-67 D- -30P 0.8 (0.9)

Adjustment Procedure Results of Improper Adjustment