Bizhubc554e C454e C364e C284e C224eQuickStartGuide

Quick Start Guide
This manual describes basic procedures users will need to know in

order to use this machine, as well as setting procedures. It also
introduces major functions, FAQs, and basic troubleshooting
procedures to make use of this machine more conveniently.
This manual also contains notes and precautions that should be
followed in order to use this machine. Please be sure to read this
manual before using this machine.
Table of contents
1 Introduction
1.1 Environmental Information............................................................................................................. 1-2
Environmental initiatives .................................................................................................................... 1-2
Energy Star®...................................................................................................................................... 1-2
What is an ENERGY STAR® Product? .............................................................................................. 1-2
Environmental benefits of power management ................................................................................. 1-2
Recycled Paper.................................................................................................................................. 1-3
Duplex printing................................................................................................................................... 1-3
1.2 Certification for USA, Canada, Mexico, Brazil and Europe area ................................................ 1-4
For U.S.A............................................................................................................................................ 1-4
For Canada ........................................................................................................................................ 1-4
For Mexico ......................................................................................................................................... 1-4
For Brazil ............................................................................................................................................ 1-4
For Europe ......................................................................................................................................... 1-4
1.3 Safety information........................................................................................................................... 1-5
Warning and precaution symbols ...................................................................................................... 1-5
Meaning of symbols........................................................................................................................... 1-5
1.4 Regulation notices ........................................................................................................................ 1-10
CE Marking (Declaration of Conformity) for users of the European Union (EU)............................... 1-10
USER INSTRUCTIONS FCC PART 15 - RADIO FREQUENCY DEVICES (for U.S.A. users)............ 1-10
INTERFERENCE-CAUSING EQUIPMENT STANDARD (ICES-003 ISSUE 4) (for Canada users) .... 1-10
For users in countries not subject to class B regulations ................................................................ 1-10
GS Certification................................................................................................................................ 1-10
Laser safety...................................................................................................................................... 1-10
Internal laser radiation...................................................................................................................... 1-11
CDRH regulations ............................................................................................................................ 1-11
For European users.......................................................................................................................... 1-11
For Denmark users........................................................................................................................... 1-12
For Finland, Sweden users .............................................................................................................. 1-12
For Norway users............................................................................................................................. 1-12
Laser safety label ............................................................................................................................. 1-13
Ozone release .................................................................................................................................. 1-13
Acoustic noise (for European users only)......................................................................................... 1-13
Notification for California Customers............................................................................................... 1-13
For EU member states only ............................................................................................................. 1-14
For EU member states only ............................................................................................................. 1-14
Telephone Cable (For users in countries subject to class B regulations) ........................................ 1-14
1.5 Caution notations and labels ....................................................................................................... 1-15
1.6 Special Notice to User .................................................................................................................. 1-16
For Canada ...................................................................................................................................... 1-16
For U.S.A.......................................................................................................................................... 1-16
For New Zealand.............................................................................................................................. 1-17
For Europe ....................................................................................................................................... 1-18
1.7 Space requirements...................................................................................................................... 1-19
bizhub C554e/C454e ....................................................................................................................... 1-19
bizhub C364e/C284e/C224e ........................................................................................................... 1-20
1.8 Operation precautions.................................................................................................................. 1-21
Power source ................................................................................................................................... 1-21
Operating environment .................................................................................................................... 1-21
Storage of copies............................................................................................................................. 1-21
Data stored in this machine ............................................................................................................. 1-21
1.9 Legal restrictions on copying ...................................................................................................... 1-22
1.10 Trademark acknowledgements ................................................................................................... 1-23
Copyright ......................................................................................................................................... 1-24
Note ................................................................................................................................................. 1-24
1.11 SOFTWARE LICENSE AGREEMENT ........................................................................................... 1-25
1.12 i-Option LK-105 v3 (Searchable PDFs) End User License Agreement..................................... 1-26
bizhub C554e/C454e/C364e/C284e/C224e Contents-1

2 About This Machine
2.1 Introduction to User's Guide.......................................................................................................... 2-2
2.1.1 Booklet manual .................................................................................................................................. 2-2
[Quick Start Guide]............................................................................................................................. 2-2
2.1.2 User's Guide CD ................................................................................................................................ 2-3
Layout of top page............................................................................................................................. 2-3
Operating environment ...................................................................................................................... 2-4
Viewing the top page ......................................................................................................................... 2-4
2.1.3 Symbols and Notations Used in This Manual .................................................................................... 2-4
Procedural instruction........................................................................................................................ 2-4
Symbols and notations ...................................................................................................................... 2-5
Notations of application names ......................................................................................................... 2-5
2.2 About this machine ......................................................................................................................... 2-6
2.2.1 Optional components (bizhub C554e/C454e).................................................................................... 2-6
2.2.2 Optional components (bizhub C364e/C284e/C224e)........................................................................ 2-9
2.2.3 Name of parts (MFP) (bizhub C554e/C454e) ................................................................................... 2-12
Front side ......................................................................................................................................... 2-12
Rear side .......................................................................................................................................... 2-13
2.2.4 Name of parts (MFP) (bizhub C364e/C284e/C224e) ....................................................................... 2-14
Front side ......................................................................................................................................... 2-14
Rear side .......................................................................................................................................... 2-15
2.2.5 Name of parts (Optional units) ......................................................................................................... 2-16
Finisher FS-535, Saddle Stitcher SD-512, Punch Kit PK-521 (bizhub C554e) ................................ 2-16
Job Separator JS-602 (bizhub C554e) ............................................................................................ 2-18
Z Folding Unit ZU-606 (bizhub C554e) ............................................................................................ 2-19
Post Inserter PI-505 (bizhub C554e) ................................................................................................ 2-20
Finisher FS-533, Punch Kit PK-519 ................................................................................................. 2-21
Job Separator JS-506...................................................................................................................... 2-22
Finisher FS-534, Saddle Stitcher SD-511, Punch Kit PK-520 ......................................................... 2-23
Large Capacity Unit LU-301/LU-204 ............................................................................................... 2-25
2.3 Power supply ................................................................................................................................. 2-26
2.3.1 Turning the power on and off........................................................................................................... 2-26
2.3.2 Operating the Power key ................................................................................................................. 2-27
2.3.3 Power save function ........................................................................................................................ 2-27
Reducing power consumption......................................................................................................... 2-28
2.4 Control Panel................................................................................................................................. 2-29
2.4.1 Name of parts .................................................................................................................................. 2-29
2.5 Touch Panel................................................................................................................................... 2-31
2.5.1 Main Menu ....................................................................................................................................... 2-31
Layout of main menu ....................................................................................................................... 2-31
Customizing the main menu ............................................................................................................ 2-32
2.5.2 Operating the Touch Panel .............................................................................................................. 2-32
Tap ................................................................................................................................................... 2-32
Double-tap ....................................................................................................................................... 2-32
Flick.................................................................................................................................................. 2-33
Drag ................................................................................................................................................. 2-33
Pan ................................................................................................................................................... 2-33
Long-tap .......................................................................................................................................... 2-33
Drag & Drop ..................................................................................................................................... 2-34
Pinch in/Pinch out............................................................................................................................ 2-34
Rotation............................................................................................................................................ 2-34
Precautions on using the Touch panel ............................................................................................ 2-35
2.5.3 How to display the keypad .............................................................................................................. 2-36
How to move the keypad ................................................................................................................. 2-36
How to close the keypad ................................................................................................................. 2-36
To display the keypad all the time ................................................................................................... 2-37
2.5.4 Entering characters .......................................................................................................................... 2-37
When typing in "Group1": ................................................................................................................ 2-37
2.6 Jobs................................................................................................................................................ 2-38
2.6.1 Job screen ....................................................................................................................................... 2-38
Contents-2 bizhub C554e/C454e/C364e/C284e/C224e

2.6.2 Multi-job function ............................................................................................................................. 2-38
2.7 Loading Paper ............................................................................................................................... 2-39
2.7.1 Loading paper in Tray 1 to Tray 4 .................................................................................................... 2-39
Applicable paper types .................................................................................................................... 2-39
How to load paper ........................................................................................................................... 2-39
2.7.2 LCT (built-in)..................................................................................................................................... 2-40
How to load paper ........................................................................................................................... 2-40
2.7.3 Loading paper into the Large Capacity Unit .................................................................................... 2-41
How to load paper ........................................................................................................................... 2-41
2.7.4 Bypass Tray ..................................................................................................................................... 2-42
Applicable paper sizes ..................................................................................................................... 2-42
How to load paper ........................................................................................................................... 2-42
3 Basic Settings and Operations

3.1 Print Function .................................................................................................................................. 3-2
3.1.1 Required settings and basic operations (For Windows OS) .............................................................. 3-2
Preparation flow ................................................................................................................................. 3-2
Operation flow.................................................................................................................................... 3-2
Checking the cable connection ......................................................................................................... 3-3
Checking network settings of this machine ....................................................................................... 3-3
Installing the printer driver ................................................................................................................. 3-4
Printing data....................................................................................................................................... 3-7
Types of printer drivers ...................................................................................................................... 3-8
3.1.2 Required settings and basic operations (For Mac OS) ...................................................................... 3-9
Operation flow.................................................................................................................................... 3-9
Checking the cable connection ....................................................................................................... 3-10
Checking network settings of this machine ..................................................................................... 3-10
Installing the printer driver ............................................................................................................... 3-12
Adding and configuring a printer driver ........................................................................................... 3-15
Printing data..................................................................................................................................... 3-17
3.2 Scan-to-Send function ................................................................................................................. 3-18
3.2.1 Various transmission methods......................................................................................................... 3-18
Sending data to your computer (SMB Send) ................................................................................... 3-18
Transmitting data as E-mail attachment (E-mail TX)........................................................................ 3-18
Saving data to the USB memory device (External memory)............................................................ 3-18
Various methods for transmitting and saving data .......................................................................... 3-19
3.2.2 Sending data to your Windows computer (SMB Send) ................................................................... 3-20
Preparation flow ............................................................................................................................... 3-20
Operation flow.................................................................................................................................. 3-20
Checklist .......................................................................................................................................... 3-22
Checking computer information ...................................................................................................... 3-22
Configuring your computer .............................................................................................................. 3-23
Registering destinations .................................................................................................................. 3-26
Sending the original ......................................................................................................................... 3-28
3.2.3 Sending data to your Mac computer (SMB Send) ........................................................................... 3-30
Operation flow.................................................................................................................................. 3-30
Configuring this machine (Mac OS X 10.7 or later).......................................................................... 3-32
Checklist .......................................................................................................................................... 3-33
Checking computer information ...................................................................................................... 3-33
Configuring your computer .............................................................................................................. 3-34
Registering destinations .................................................................................................................. 3-36

3.2.4 Transmit the scanned data via E-mail (E-mail TX) ........................................................................... 3-40
Operation flow.................................................................................................................................. 3-40
Configuring the E-mail transmission environment ........................................................................... 3-42
Configuring administrator information ............................................................................................. 3-43
3.3 Fax Function .................................................................................................................................. 3-46
3.3.1 Required settings and basic operations .......................................................................................... 3-46
Operation flow.................................................................................................................................. 3-46
Registering transmission information .............................................................................................. 3-48
Selecting the dialing method ........................................................................................................... 3-49
3.3.2 Sending a fax directly from a PC (PC-FAX TX) ................................................................................ 3-52
Operation flow.................................................................................................................................. 3-52
Installing the fax driver ..................................................................................................................... 3-55
Sending data.................................................................................................................................... 3-57
3.4 Copy Function ............................................................................................................................... 3-59
Basic operations .............................................................................................................................. 3-59
User authentication.......................................................................................................................... 3-61
3.5 Registering a destination ............................................................................................................. 3-62
3.5.1 Registering an address book ........................................................................................................... 3-62
Using the Control Panel to register an address book - Registration from Utility............................. 3-62
Using the Control Panel to register an address book - Registration in scan/fax mode .................. 3-64
Using a computer to register a one-touch destination .................................................................... 3-66
3.5.2 Information required to register a destination.................................................................................. 3-68
3.5.3 Registering a group.......................................................................................................................... 3-69
Registering a new group .................................................................................................................. 3-69
3.5.4 Retrieving a registered destination .................................................................................................. 3-71
Retrieving a destination ................................................................................................................... 3-71
Specifying a destination................................................................................................................... 3-73
3.6 Using a USB memory device ....................................................................................................... 3-74
3.6.1 Printing data in a USB memory device ............................................................................................ 3-74
Printing data..................................................................................................................................... 3-74
3.6.2 Saving the scanned data in the USB memory device (External memory) ....................................... 3-77
Specifying functions to be permitted for external memory.............................................................. 3-77
Saving data in the USB memory device .......................................................................................... 3-79
3.7 Using the guidance function ........................................................................................................ 3-81
3.7.1 Guidance screen .............................................................................................................................. 3-81
Getting help on the currently displayed screen: .............................................................................. 3-81
Getting help on the desired function or procedure:......................................................................... 3-84
Help Menu list .................................................................................................................................. 3-86
4 Advanced Functions
4.1 Using advanced functions.............................................................................................................. 4-2
4.1.1 What are advanced functions? .......................................................................................................... 4-2
4.1.2 Association with application .............................................................................................................. 4-3
4.1.3 Registering the i-Option license......................................................................................................... 4-3
Registering the i-Option license......................................................................................................... 4-4
Enabling the i-Option function ........................................................................................................... 4-6
Configuring each function.................................................................................................................. 4-8
4.2 Using the Voice Guidance .............................................................................................................. 4-9

4.2.1 Required Settings and Procedures.................................................................................................... 4-9
Operation flow.................................................................................................................................... 4-9
Enabling the voice guidance function .............................................................................................. 4-10
Assigning the voice guidance function to the Register key ............................................................. 4-11
Specifying the volume and speed.................................................................................................... 4-12
Operating the voice guidance .......................................................................................................... 4-13
Keypad operations for voice guidance ............................................................................................ 4-14
5 Frequently Asked Questions

5.1 Print .................................................................................................................................................. 5-2
5.1.1 Q1. Can I print data on an envelope or postcard? ............................................................................ 5-2
Operation procedure.......................................................................................................................... 5-2
5.1.2 Q2. Can I print on custom size paper? .............................................................................................. 5-5
5.1.3 Q3. Can I directly print a file in a USB memory device?.................................................................... 5-7
5.1.4 Q4. Can printing be restricted by user?............................................................................................. 5-9
How to set.......................................................................................................................................... 5-9
5.1.5 Q5. What types are available for printing finish? ............................................................................. 5-11
Staple ............................................................................................................................................... 5-11
Punch ............................................................................................................................................... 5-12
Center Staple & Fold........................................................................................................................ 5-12
Fold .................................................................................................................................................. 5-12
Operation procedure........................................................................................................................ 5-12
5.1.6 Q6. Can I print on very long sheets of paper such as a banner? .................................................... 5-13
How to set........................................................................................................................................ 5-13
5.2 Scan................................................................................................................................................ 5-17
5.2.1 Q1. Can frequently used destinations be registered? ..................................................................... 5-17
5.3 Fax .................................................................................................................................................. 5-18
5.3.1 Q1. Can I check fax transmission and reception logs? ................................................................... 5-18
5.3.2 Q2. Can I send a fax to a number of destinations at one time? ...................................................... 5-18
Operation procedure: Selecting multiple addresses from the address book .................................. 5-18
Operation procedure: Directly entering multiple destinations ......................................................... 5-19
5.3.3 Q3. Can I register more than one sender name to appear on faxes so that different ones can
be used in different use cases? ....................................................................................................... 5-20
How to set: Registering sender names............................................................................................ 5-20
How to set: Selecting a sender name upon fax transmission ......................................................... 5-21
5.3.4 Q4. Is it possible to cut down on the communications expenses by using a network?.................. 5-22
Operation procedure: Sending an Internet fax ................................................................................ 5-22
Operation procedure: Sending an IP address fax ........................................................................... 5-23
5.3.5 Q5. How can I avoid printing out unwanted faxes?......................................................................... 5-24
Operation procedure: Configuring to save received faxes in a User Box........................................ 5-24
How to set: Printing faxes saved in a User Box............................................................................... 5-24
5.3.6 Q6. Can I forward an incoming fax? ................................................................................................ 5-25
How to set........................................................................................................................................ 5-26
5.3.7 Q7. Can I directly fax a file on my computer without leaving my desk?.......................................... 5-27
5.4 Copy ............................................................................................................................................... 5-28
5.4.1 Q1. Can I print on paper of a custom size? ..................................................................................... 5-28
Operation procedure: Copying on paper of a custom size.............................................................. 5-28
Operation procedure: Registering a custom size of paper in memory ............................................ 5-29
Operation procedure: Recalling the custom size registered in memory.......................................... 5-30
5.4.2 Q2. Can I copy on an envelope or postcard? .................................................................................. 5-31
Operation procedure: Copying on envelopes.................................................................................. 5-31
Operation procedure: Copying on postcards .................................................................................. 5-32
5.4.3 Q3. Can I check the finish before starting copying?........................................................................ 5-34
How to set: Checking the finish with a preview image .................................................................... 5-34

How to set: Checking the finish by outputting one copy................................................................. 5-35
5.4.4 Q4. Can I easily copy various cards such as an insurance card or driver license card?................. 5-36
5.5 User Box ........................................................................................................................................ 5-38
5.5.1 Q1. Can I create a User Box, or print or download a file in a User Box? ........................................ 5-38
Operation procedure: Using Web Connection................................................................................. 5-38
Operation procedure: Using the Windows file sharing function ...................................................... 5-38
5.6 Other............................................................................................................................................... 5-40
5.6.1 Q1. Can more than one computer use the same settings for the printer driver? ............................ 5-40
Operation procedure : Preparing for an install package.................................................................. 5-40
Operation procedure: Creating an install package .......................................................................... 5-40
Operation procedure: Executing the install package....................................................................... 5-41
5.6.2 Q2. Can I restrict available functions by user? ................................................................................ 5-41
How to set........................................................................................................................................ 5-41
5.6.3 Q3. Can I change the keying and operation sounds of this machine? ............................................ 5-43
How to set........................................................................................................................................ 5-43
5.6.4 Q4. User authentication seems to be enabled on this machine. How can I be authenticated and
allowed to operate this machine?.................................................................................................... 5-46
How to set: Getting authenticated as a user on this machine ......................................................... 5-47
How to set: Getting authenticated as a user on the printer driver................................................... 5-47
5.6.5 Q5. The power is input all day. Is there any way to alleviate concerns about electricity
charges? .......................................................................................................................................... 5-48
How to set........................................................................................................................................ 5-49
5.6.6 Q6. What action should be taken if the administrator password is lost? ........................................ 5-51
6 Troubleshooting
6.1 Main Messages and Remedies...................................................................................................... 6-2
6.1.1 When a Message Appears to Replace Consumables or Carry Out Cleaning.................................... 6-2
6.1.2 When a paper jam message persists................................................................................................. 6-3
6.1.3 When an error message appears....................................................................................................... 6-4
6.1.4 When [Stabilizing image.] appears..................................................................................................... 6-5
6.2 When Printing Quality Has Deteriorated....................................................................................... 6-6
6.2.1 Cleaning the Electrostatic Charger Wire............................................................................................ 6-6
6.2.2 Cleaning the Print Head Glass........................................................................................................... 6-7
6.3 When the Machine Cannot Be Powered On ................................................................................. 6-9
6.4 When the Touch Panel Is Not Visible .......................................................................................... 6-10
6.5 When a Message Appears to Replace Consumables or Carry Out Cleaning ......................... 6-12
When staples in the finisher have run out ........................................................................................ 6-12
When the punch scrap box is full .................................................................................................... 6-12
When toner is running out in the Toner Cartridge............................................................................ 6-13
When a Waste Toner Box is full ....................................................................................................... 6-13
6.5.1 Replacing a Toner Cartridge ............................................................................................................ 6-14
bizhub C554e/C454e ....................................................................................................................... 6-14
bizhub C364e/C284e/C224e ........................................................................................................... 6-15
6.5.2 Replacing a Waste Toner Box ......................................................................................................... 6-16
bizhub C554e/C454e ....................................................................................................................... 6-16
bizhub C364e/C284e/C224e ........................................................................................................... 6-17
7 Index
7.1 Index by item ................................................................................................................................... 7-2

1
Introduction
Introduction Chapter 1
Environmental Information 1.1
1
Chapter 1
1 Introduction
Introduction
This [Quick Start Guide] uses illustrations to describe operating procedures for the most commonly used
functions in an easy-to-understand way.
Start by using this manual to become proficient with the useful functions that this machine offers.
For details on the various functions, refer to the User’s Guides on the User’s Guide CD included with this
machine.
In order to operate the machine safely and properly, be sure to read the safety information on page 1-5 of
this manual before use.
In addition, this manual contains the following information. Be sure to read the manual before using the ma-
chine.
- Items that must be observed to use the machine safely
- Information regarding product safety
- Precautions when using the machine
- Descriptions on trademarks and copyrights
The illustrations and screens used in this manual may appear slightly different from views of the actual equip-
ment and screens.
1.1 Environmental Information
Environmental initiatives
The company continuously strives to reduce the negative environmental impacts of all stages of its business
operations.
As part of such activities, the company is implementing resource-saving steps by reducing the number of
pages in the User's Guide.
For the information necessary to operate the machine, please refer to the bundled User's Guide CD (HTML
format). This guide has an excellent search function.
Functions such as keyword search and filtering by purpose are very useful to help users find what they need
to know.
Energy Star®
As an ENERGY STAR® Partner, this machine meets the ENERGY STAR® Guidelines for energy efficiency.
What is an ENERGY STAR® Product?

An ENERGY STAR® product has a special feature that allows it to automatically switch to a "low-power
mode" after a period of inactivity. An ENERGY STAR® product uses energy more efficiently, saves you money
on utility bills and helps protect the environment.
Environmental benefits of power management

Electricity consumption of a device depends on both its properties and the way of using the device.
Suitable power management setting offers you resource saving usage way. By setting the time to go into
power saving modes (e.g. sleep mode) shorter (or optimal), electricity consumption can be reduced.
1-2 bizhub C554e/C454e/C364e/C284e/C224e

1.1 Environmental Information
1
Chapter 1
Recycled Paper
This product can print on recycled paper and environmental stewardship initiatives certified paper which
complies with European standard EN 12281 as well as virgin paper. In addition it can print on lighter paper,
64g/m2 for example. Using such light paper contributes to resources-saving.
Introduction
Duplex printing
With a product which has a duplex unit, you can print on both sides of paper automatically.
Using this function leads to reducing consumption of natural resources and your cost.
Attached printer driver provides this duplex printing function as initial setting in your computer (The setting
can be changed after installation manually).
bizhub C554e/C454e/C364e/C284e/C224e 1-3

Certification for USA, Canada, Mexico, Brazil and Europe area 1.2
1
Chapter 1
1.2 Certification for USA, Canada, Mexico, Brazil and Europe area
For U.S.A
Introduction
This product is certified by the following model name in U.S.A.

Konica Minolta branded model bizhub C554e, bizhub C454e and C302300 (bizhub C364e, bizhub C284e and
bizhub C224e).
For Canada
This product is certified by the following model name in Canada.
bizhub C224e).
For Mexico
This product is certified by the following model name in Mexico.
bizhub C224e).
For Brazil
This product is certified by the following model name in Brazil.
bizhub C224e).
For Europe
This product is certified by the following model name in Europe.
bizhub C224e).

1.3 Safety information
1
Chapter 1
This section contains detailed instructions on the operation and maintenance of this machine. To achieve op-
timum utility of this device, all operators should carefully read and follow the instructions in this manual.
Introduction
Please read the following section before connecting the machine to the supply. It contains important infor-
mation related to user safety and preventing equipment problems.
Please keep this manual in a handy place near the machine.
Make sure you observe all of the precautions appear in each section of this manual.
KM_Ver.06OE
Reference
- Some parts of the contents of this section may not correspond with the purchased product.
Warning and precaution symbols

The following indicators are used on the warning labels or in the manuals to categorize the level of safety
warnings.
WARNING Ignoring this warning could cause serious injury or even death.
CAUTION Ignoring this caution could cause injury or damage to property.
Meaning of symbols
A triangle indicates a danger against which you should take precaution.

This symbol warns against cause burns.
A diagonal line indicates a prohibited course of action.
This symbol warns against dismantling the device.
A solid circle indicates an imperative course of action.
This symbol indicates you must unplug the device.
Disassemble and modification
WARNING
• Do not modify this product, as a fire, electrical shock, or breakdown could
result. If the product employs a laser, the laser beam source could cause
blindness.
• Do not attempt to remove the covers and panels which have been fixed
to the product. Some products have a high-voltage part or a laser beam
source inside that could cause an electrical shock or blindness.
Power cord
WARNING
• Use only the power cord supplied in the package. If a power cord is not
supplied, only use the power cord and plug that is specified in POWER
CORD INSTRUCTION. Failure to use this cord could result in a fire or
electrical shock.
• Use the power cord supplied in the package only for this machine and
NEVER use it for any other product. Failure to observe this precaution
could result in a fire or electrical shock.

Safety information 1.3
1
Chapter 1
Power cord
• Do not scratch, abrade, place a heavy object on, heat, twist, bend, pull
on, or damage the power cord. Use of a damaged power cord (exposed
core wire, broken wire, etc.) could result in a fire or breakdown.
Introduction
Should any of these conditions be found, immediately turn OFF the power
switch, unplug the power cord from the power outlet, and then call your
authorized service representative.
Power source
WARNING
• Use only the power source voltage specified on the machine. Failure to
do that could result in a fire or electrical shock.
• Do not use a multiple outlet adapter to connect any other appliances or

machines.
Use of a power outlet for more than the marked current value could result
in a fire or electrical shock.
• Do not use an extension cord in principle. Use of an extension cord could
cause a fire or electrical shock. Contact your authorized service repre-
sentative if an extension cord is required.
CAUTION
• The outlet must be near the equipment and easily accessible. Otherwise
you can not pull out the power plug when an emergency occurs.
Power plug
WARNING
• Do not unplug and plug in the power cord with a wet hand, as an electrical
shock could result.
• Plug the power cord all the way into the power outlet. Failure to do this
could result in a fire or electrical shock.
CAUTION
• Do not place any objects around the power plug, as the power plug may
be difficult to pull out when an emergency occurs.
• Do not tug the power cord when unplugging. Pulling on the power cord
could damage the cord, resulting in a fire or electrical shock.
• Remove the power plug from the outlet more than one time a year and
clean the area between the plug terminals. Dust that accumulates be-
tween the plug terminals may cause a fire.

1
Chapter 1
Grounding
WARNING
Introduction
• Make sure to ground this product. (Connect the power cord to an electri-
cal outlet that is equipped with a grounding terminal.) Failure to do so and
an unlikely event of leakage could result in a fire or electrical shock.
Installation
WARNING
• Do not place a flower vase or other container that contains water, or metal
clips or other small metallic objects on this product. Spilled water or me-
tallic objects dropped inside the product could result in a fire, electrical
shock, or breakdown.
Should a piece of metal, water, or any other similar foreign matter get in-
side the product, immediately turn OFF the power switch, unplug the
power cord from the power outlet, and then call your authorized service
representative.
• Do not use flammable sprays, liquids, or gases inside or near this ma-
chine. Do not clean the inside of this machine using a flammable gas
duster. A fire or explosion could result.
CAUTION
• After installing this product, mount it on a secure base. If the unit moves
or falls, it may cause personal injury.
• Do not place the product in a dusty place, or a site exposed to soot or

steam, near a kitchen table, bath, or a humidifier. A fire, electrical shock,
or breakdown could result.
• Do not place this product on an unstable or tilted bench, or in a location
subject to a lot of vibration and shock. It could drop or fall, causing per-
sonal injury or mechanical breakdown.
• Do not let any object plug the ventilation holes of this product. Heat could
accumulate inside the product, resulting in a fire or malfunction.
Ventilation
CAUTION
• Using this product in a poorly ventilated room for a long time or producing
a large volume of copies or prints may cause the odor of exhaust air from
the machine. Ventilate the room well.

Safety information 1.3
1
Chapter 1
Actions in response to troubles
WARNING
Introduction
• Do not keep using this product, if this product becomes inordinately hot
or emits smoke, or unusual odor or noise. Immediately turn OFF the pow-
er switch, unplug the power cord from the power outlet, and then call your
authorized service representative. If you keep on using it as is, a fire or
electrical shock could result.
• Do not keep using this product, if this product has been dropped or its
cover damaged. Immediately turn OFF the power switch, unplug the
power cord from the power outlet, and then call your authorized service
representative. If you keep on using it as is, a fire or electrical shock could
result.
CAUTION
• The inside of this product has areas subject to high temperature, which
may cause burns.
When checking the inside of the unit for malfunctions such as a paper
misfeed, do not touch the locations (around the fusing unit, etc.) which
are indicated by a "Caution HOT" caution label.
Consumables
WARNING
• Do not throw the toner cartridge or toner into an open flame. The hot ton-
er may scatter and cause burns or other damage.
CAUTION
• Do not leave toner-related parts (toner units, PC drum units, imaging units
or developing units) within easy reach of children. Licking any of these
parts or ingesting toner could damage your health.
• Do not store toner-related parts (toner units, PC drum units, imaging units
or developing units) near devices susceptible to magnetism, such as pre-
cision equipment and data storage devices, otherwise they may malfunc-
tion. They could cause these products to malfunction.
When moving the machine
CAUTION
• Whenever moving this product, be sure to disconnect the power cord and
other cables. Failure to do this could damage the cord or cable, resulting
in a fire, electrical shock, or breakdown.
• When moving this product, always hold it at the locations specified in the
User’s Guide or other documents. If the unit is moved while held at loca-
tions other than those specified, it may fall, causing severe personal inju-
ry.
When using the machine
CAUTION
• When using the machine, do not look at the light of the lamp for a pro-
longed time. Eyestrain could result.

1
Chapter 1
Papers
CAUTION
Introduction
• Do not use stapled paper, conductive paper (such as silver paper or car-
bon paper) or treated heat-sensitive/inkjet paper, otherwise a fire may re-
sult.
When the Fax is not installed:
Before successive holidays
CAUTION
• Unplug the product when you will not use the product for long periods of
time.

Regulation notices 1.4
1
Chapter 1
1.4 Regulation notices
CE Marking (Declaration of Conformity) for users of the European Union (EU)

Introduction
This product complies with the following EU directives:

2009/125/EC, 2006/95/EC, 2004/108/EC and 1999/5/EC directives.
This declaration is valid for the area of the European Union.
This device must be used with a shielded interface cable. The use of non-shielded cables is likely to result in
interference with radio communications and is prohibited under CISPR rules and local rules.
D.o.C. is available at "http://www.konicaminolta.eu/".
USER INSTRUCTIONS FCC PART 15 - RADIO FREQUENCY DEVICES (for

U.S.A. users)
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pur-
suant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interfer-
ence to radio communications. Operation of this equipment in a residential area is likely to cause harmful in-
terference in which case the user will be required to correct the interference at his own expense.
7 WARNING
- The design and production of this unit conform to FCC regulations, and any changes or modifications
must be registered with the FCC and are subject to FCC control. Any changes made by the purchaser
or user without first contacting the manufacturer will be subject to penalty under FCC regulations.
- This device must be used with a shielded interface cable. The use of non-shielded cables is likely to
result in interference with radio communications and is prohibited under FCC rules.
INTERFERENCE-CAUSING EQUIPMENT STANDARD (ICES-003 ISSUE 4) (for

Canada users)
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
For users in countries not subject to class B regulations
7 WARNING
- This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
- This device must be used with a shielded interface cable. The use of non-shielded cables is likely to
result in interference with radio communications and is prohibited under CISPR rules and local rules.
GS Certification
bizhub C224e).
Laser safety
This is a digital machine which operates using a laser. There is no possibility of danger from the laser provided
the machine is operated according to the instructions in the manuals.
Since radiation emitted by the laser is completely confined within protective housing, the laser beam cannot
escape from the machine during any phase of user operation.
This machine is certified as a Class 1 laser product: This means the machine does not produce hazardous
laser radiation.

1
Chapter 1
Internal laser radiation
Maximum Average Radiation Power: 11.2 μW (bizhub C554e) / 9.4 μW (bizhub C454e) / 7.4 μW (C302300
(bizhub C364e)) / 6.0 μW (C302300 (bizhub C284e and bizhub C224e)) at the laser aperture of the print head
unit.
Introduction
Wavelength: 770-800 nm
This product employs a Class 3B laser diode that emits an invisible laser beam.
The laser diode and the scanning polygon mirror are incorporated in the print head unit.
The print head unit is NOT A FIELD SERVICE ITEM:
Therefore, the print head unit should not be opened under any circumstances.
Laser Aperture of
the Print Head Unit
Print Head
CDRH regulations
This machine is certified as a Class 1 Laser product under Radiation Performance Standard according to the
Food, Drug and Cosmetic Act of 1990. Compliance is mandatory for Laser products marketed in the United
States and is reported to the Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug
Administration of the U.S. Department of Health and Human Services (DHHS). This means that the device
does not produce hazardous laser radiation.
The label shown on page 1-13 indicates compliance with the CDRH regulations and must be attached to la-
ser products marketed in the United States.
7 CAUTION
Use of controls, adjustments or performance of procedures other than those specified in this manual
may result in hazardous radiation exposure.
- This is a semiconductor laser. The maximum power of the laser diode is 15 mW and the wavelength is
770-800 nm.
For European users
7 CAUTION
Use of controls, adjustments or performance of procedures other than those specified in this manual
may result in hazardous radiation exposure.
- This is a semiconductor laser. The maximum power of the laser diode is 15 mW and the wavelength is
770-800 nm.

1
Chapter 1
For Denmark users
7 ADVARSEL
Introduction
Usynlig laserstråling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for
stråling. Klasse 1 laser produkt der opfylder IEC60825 sikkerheds kravene.
- Dette er en halvlederlaser. Laserdiodens højeste styrke er 15 mW og bølgelængden er 770-800 nm.
For Finland, Sweden users

LOUKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
7 VAROITUS
Laitteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän
turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
- Tämä on puolijohdelaser. Laserdiodin sunrin teho on 15 mW ja aallonpituus on 770-800 nm.
7 VARNING
Om apparaten används på annat sätt än i denna bruksanvisning specificerats, kan användaren utsät-
tas för osynlig laserstrålning, som överskrider gränsen för laserklass 1.
- Det här är en halvledarlaser. Den maximala effekten för laserdioden är 15 mW och våglängden är 770-
800 nm.
7 VAROITUS
- Avattaessa ja suojalukitus ohitettaessa olet alttiina näkymättömälle lasersäteilylle. Älä katso säteeseen.
7 VARNING
- Osynlig laserstrålning när denna del är öppnad och spärren är urkopplad. Betrakta ej strålen
For Norway users
7 ADVARSEL!
Dersom apparatet brukes på annen måte enn spesifisert i denne bruksanvisning, kan brukeren ut-
settes for unsynlig laserstråling som overskrider grensen for laser klass 1.
- Dette en halvleder laser. Maksimal effekt till laserdiode er 15 mW og bølgelengde er 770-800 nm.

1
Chapter 1
Laser safety label
A laser safety label is attached to the outside of the machine, as shown below.
Introduction
bizhub C554e/C454e bizhub C364e /C284e/C224e
Only for the U.S.A.

Only for the U.S.A.
Only for the Europe Only for the Europe
Other Area
Other Area
Ozone release
Locate the Machine in a Well-Ventilated Room
A negligible amount of ozone is generated during normal operation of this machine. An unpleasant odor may,
however, be created in poorly ventilated rooms during extensive machine operations. For a comfortable,
healthy and safe operating environment, it is recommended that the room be well ventilated.
Placer l’appareil dans une pièce largement ventilée
Une quantité d’ozone négligable est dégagée pendant le fonctionnement de l’appareil quand celui-ci est uti-
lisé normalement. Cependant, une odeur désagréable peut être ressentie dans les pièces dont l’aération est
insuffisante et lorsque une utilisation prolongée de l’appareil est effectuée. Pour avoir la certitude de travailler
dans un environnment réunissant des conditions de confort, santé et de sécurité, il est préférable de bien
aérer la pièce ou se trouve l’appareil.
Acoustic noise (for European users only)

Der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäß EN ISO 7779.
Notification for California Customers

This product uses a CR Lithium Battery which contains perchlorate material.
This perchlorate warning applies to perchlorate-containing lithium batteries sold or distributed in California,
USA.
"Perchlorate Material - Special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate."

1
Chapter 1
For EU member states only

This symbol means: Do not dispose of this product together with your household
waste!
Introduction
Please refer to the information of your local community or contact our dealers re-
grading the proper handling of end-of-life electric and electronic equipments. Re-
cycling of this product will help to conserve natural resources and prevent
potential negative consequences for the environment and human health caused
by inappropriate waste handling.
For EU member states only

This product complies with RoHS (2011/65/EU) Directive.
Telephone Cable (For users in countries subject to class B regulations)

Connect a telephone cable with a ferrite core to the telecommunication port of this machine. (Connect the
modular jack on the ferrite-core-equipped end of the telephone cable to the telecommunication port.)

1.5 Caution notations and labels
1
Chapter 1
1.5 Caution notations and labels
Safety precaution notations and labels appear on this machine at the following positions.Be very careful that
an accident does not occur when operations such as removing paper jams and staple jams are performed.
Introduction
NOTICE
Do not remove caution labels or notations. If any caution label or caution notation is soiled, please clean to
make legible. If you cannot make them legible, or if the caution label or notation is damaged, please contact
your service representative.

Special Notice to User 1.6
1
Chapter 1
1.6 Special Notice to User
For Canada
Introduction
NOTICE:
This product meets the applicable Industry Canada technical specifications.
The Ringer Equivalence Number is an indication of the maximum number of devices allowed to be connected
to a telephone interface. The termination on an interface may consist of any combination of devices subject
only to the requirement that the sum of the RENs of all the devices does not exceed five.
AVIS:
Le present materiel est conforme aux specifications techniques applicables d’Industrie Canada.
L’indice d’equivalence de la sonnerie (IES) sert a indiquer le nombre maximal de terminaux qui peuvent etre
raccordes a une interface telephonique. La terminaison d’une interface peut consister en une combinaison
quelconque de dispositifs, a la seule condition que la somme d’indices d’equivalence de la sonnerie de tous
les dispositifs n’excede pas 5.
For U.S.A.
FCC PART 68 REQUIREMENTS:
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the
cover of this equipment is a label that contains, among other information, a product identifier in the format
US:AAAEQ##TXXXX. If required, this information must be provided to the telephone company.
This equipment uses certification jack USOC RJ11C.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply
with the applicable FCC Part 68 rules and requirements adopted by the ACTA.
A compliant telephone cord and modular plug is provided with this product. It is designed to be connected
to a compatible modular jack that is also compliant. See installation instructions for details.
The REN is used to determine the number of devices that may be connected to a telephone line. Excessive
RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but
not all areas, the sum of RENs should not exceed five (5.0).
To be certain of the number of devices that may be connected to a line, as determined by the total RENs,
contact the local telephone company For products approved after July 23, 2001, the REN for this product is
part of the product identifier that has the format US: US:AAAEQ##TXXXX.. The digits represented by ## are
the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown
on the label.
If this equipment FK-511 and FK-508 causes harm to the telephone network, the telephone company will no-
tify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t
practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of
your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures that could
affect the operation of the equipment. If this happens the telephone company will provide advance notice in
order for you to make necessary modifications to maintain uninterrupted service.
If trouble is experienced with this equipment FK-511 and FK-508, for repair or warranty information, please
contact the Konica Minolta dealer location where you purchased this equipment. If the equipment is causing
harm to the telephone network, the telephone company may request that you disconnect the equipment until
the problem is resolved.

1.6 Special Notice to User
1
Chapter 1
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public
service commission or corporation commission for information. If you home has specially wired alarm equip-
ment connected to the telephone line, ensure the installation of FK-511 and FK-508 does not disable you
alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone
Introduction
company or a qualified installer.
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other
electronic device, including FAX machines, to send any message unless such message clearly contains in a
margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and
time it is sent and an identification of the business or other entity, or other individual sending the message
and the telephone number of the sending machine or such business, other entity, or individual. (The tele-
phone number provided may not be a 900 number or any other number for which charges exceed local or
long-distance transmission charges.)
In order to program this information into your FAX machine, you should complete the following steps: See
[Sending by Renaming the Sender ([Fax Header Settings])], of the User's Guide [Fax].
WARNING/CAUTION Explained
WARNING
The exclamation point within an equilateral triangle followed by the word "Warning" is intended to alert
the user to the possibility that a disregard for the warning may result in fatal hazards or critical injuries. Be
sure to focus your attention on the Warning headings when reading this Quick Start Guide.
CAUTION
The exclamation point within an equilateral triangle followed by the word "Caution" is intended to alert the
user to the possibility that a disregard for the caution may result in minor injuries or in physical damage.
Be sure to focus your attention on the Caution headings when reading this Quick Start Guide.
For New Zealand

This device is equipped with pulse dialing while the Telecom standard is DTMF tone dialing. There is no guar-
antee that Telecom lines will always continue to support pulse dialing.
Use of pulse dialing, when this equipment is connected to the same line as other equipment, may give rise
to bell tinkle or noise and may also cause a false answer condition. Should such problems occur, the user
should not contact the Telecom Fault Service.
This equipment may not provide for the effective hand-over of a call to another device connected to the same
line.
This equipment does not fully meet Telecom’s impedance requirements. Performance limitations may occur
when used in conjunction with some parts of the network. Telecom will accept no responsibility should diffi-
culties arise in such circumstances.
The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that
the item complies with minimum conditions for connection to its network. It indicates no endorsement of the
product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any
item will work correctly in all respects with another item of Telepermitted equipment of a different make or
model, nor does it imply that any product is compatible with all of Telecom’s network services.
The automatic calling functions of this equipment must not be used to cause a nuisance to other customers.
Telepermitted equipment only may be connected to the auxiliary telephone port. The auxiliary port is not spe-
cifically designed for 3-wire connected equipment. 3-wire might not respond to incoming ringing when con-
nected to this port.

Special Notice to User 1.6
1
Chapter 1
For Europe
The Facsimile has been approved in accordance with Council Decision 1999/5/ EC for pan-European single
terminal connection to the public switched telephone network (PSTN). However, due to differences between
the individual PSTNs provided in different countries, the approval does not, of itself, give an unconditional
Introduction
assurance of successful operation on every PSTN network terminal point.

In the event of problems, you should contact your equipment supplier in the first instance.

1.7 Space requirements
1
Chapter 1
1.7 Space requirements
To ensure that machine operation, consumables replenishing, part replacement, and regular maintenance
can easily be performed, adhere to the recommended space requirements detailed below.
Introduction
bizhub C554e/C454e
100-3/8 (2548) 49-1/16 (1246)
7-5/16 9-3/8 16-7/8
34-11/16 (881) (185) 49 (1244) (238) (428) 32-3/16 (818)
15-3/16
(386)
61-1/8 (1553)
36-1/4 (921)
9-11/16
(246)
bizhub C554e+PC-210+FS-535+SD-512+ZU-606+PI-505+LU-204 Unit: inch (mm)
80-3/8 (2041) 49-1/16 (1246)

15-13/16 16-7/8
25-7/8 (658) 38-11/16 (982) (401) (428) 32-3/16 (818)
15-3/16
(386)
61-1/8 (1553)
36-1/4 (921)
9-11/16
(246)
bizhub C554e/C454e+PC-210+FS-534+SD-511+LU-301 Unit: inch (mm)
49-1/16 (1246)
52-7/16 (1332)
16-7/8
11-5/8 (428) 32-3/16 (818)
6-11/16 34-1/8 (867) (295)
(170)
15-3/16
(386)
61-1/8 (1553)
36-1/4 (921)
9-11/16
(246)
bizhub C554e/C454e+PC-210+FS-533+MK-730 Unit: inch (mm)

Space requirements 1.7
1
Chapter 1
bizhub C364e/C284e/C224e
62-7/8 (1597) 48-13/16 (1240)
16-7/8
Introduction
26 (660) 36-7/8 (937) (428) 31-15/16 (812)
15-11/16
(398)
(246) 35-11/16 (906)
61 (1550)
9-11/16
bizhub C364e/C284e/C224e + DF-624 + PC-210 + FS-534 + SD-511 Unit: inch (mm)
43-9/16 (1107) 48-13/16 (1240)

16-7/8
6-11/16 36-7/8 (937) (428) 31-15/16 (812)
(170)
15-11/16
(398)
(246) 35-11/16 (906)
61 (1550)
9-11/16
bizhub C364e/C284e/C224e + DF-624 + PC-210 + FS-533 Unit: inch (mm)
45-3/4 (1162) 48-13/16 (1240)

11-5/8 16-7/8
34-1/8 (867) (295) (428) 31-15/16 (812)
15-11/16
(398)
(246) 35-11/16 (906)
61 (1550)
9-11/16
bizhub C364e/C284e/C224e + DF-624 + PC-210 + JS-506 + MK-730 Unit: inch (mm)
NOTICE
Be sure to allow a clearance of 8 inches (200 mm) or more at the back of this machine for the ventilation duct.

1.8 Operation precautions
1
Chapter 1
1.8 Operation precautions
To ensure the optimum performance of this machine, observe the precautions described below.
Introduction
Power source
The power source requirements are as follows.
- Voltage fluctuation: Maximum ± 10% (at 110 V/120 V/220 to 240 V AC)
- Frequency fluctuation: Maximum ± 3 Hz (at 50 Hz/60 Hz)
– Use a power source with as little voltage or frequency fluctuations as possible.
Operating environment
The environmental requirements for correct operation of the machine are as follows.
- Temperature: 50°F (10°C) to 86°F (30°C) with fluctuations of no more than 18°F (10°C) within an hour
- Humidity: 15% to 85% with fluctuations of no more than 10% within an hour
Storage of copies
To store copies, follow the recommendation listed below.
- Copies that are to be kept for a long time should be kept where they are not exposed to light in order
to prevent them from fading.
- Adhesive that contains solvent (e.g., spray glue) may dissolve the toner on copies.
- Color copies have a thicker layer of toner than normal black-and-white copies. Therefore, when a color
copy is folded, the toner at the fold may peel off.
Data stored in this machine

For the machine with hard disk, it is suggested to delete all data stored in all hard disk areas using the over-
write all data function to prevent leakage of data prior to transfer or disposal of the machine, or returning of
the leased machine.
For details of the overwrite all data function, refer to the User's Guide CD. Contact your service representative
before deleting data.
It is recommended to backup HDD periodically as the measures for HDD defect. For the detail information of
HDD backup, contact your service representative.

Legal restrictions on copying 1.9
1
Chapter 1
1.9 Legal restrictions on copying

Certain types of originals must never be copied with the purpose or intent to pass copies of such originals
off as the originals.
Introduction
The following is not a complete list, but is meant to be used as a guide to responsible copying.
<Financial Instruments>
- Personal checks
- Traveler’s checks
- Money orders
- Certificates of deposit
- Bonds or other certificates of indebtedness
- Stock certificates
<Legal Originals>
- Food stamps
- Postage stamps (canceled or uncanceled)
- Checks or drafts drawn by government agencies
- Internal revenue stamps (canceled or uncanceled)
- Passports
- Immigration papers
- Motor vehicle licenses and titles
- House and property titles and deeds
<General>
- Identification cards, badges, or insignias
- Copyrighted works without permission of the copyright owner
In addition, it is prohibited under any circumstances to copy domestic or foreign currencies, or works of art
without permission of the copyright owner.
When in doubt about the nature of an original, consult with legal counsel.
NOTICE
This machine provides the forgery prevention function in order to prevent financial instruments from being
copied illegally.
We appreciate your understanding that printed images may infrequently have some noise or image data may
not be stored under certain circumstances due to this forgery prevention function.

1.10 Trademark acknowledgements
1
Chapter 1
1.10 Trademark acknowledgements
KONICA MINOLTA, the KONICA MINOLTA logo, Giving Shape to Ideas, PageScope, and bizhub are regis-
tered trademarks or trademarks of KONICA MINOLTA, INC.
Introduction
Netscape is a registered trademark of Netscape Communications Corporation in the United States and other
countries.
Mozilla and Firefox are trademarks of the Mozilla Foundation.
Novell and Novell NetWare are registered trademarks of Novell, Inc. in the United States and other countries.
Microsoft, Windows, Windows Vista, Windows 7, and Windows 8 are either registered trademarks or trade-
marks of Microsoft Corporation in the United States and/or other countries.
PowerPC is a trademark of IBM Corporation in the United States, or other countries, or both.
In regard to the Citrix Technology Member
KONICA MINOLTA, INC. is a Citrix Technology Member
The Citrix Technology Member is a program that, in combination with a solution of Citrix, promotes and de-
velops solutions in order to be an industry leader in providing customers with better solutions.
XenAppTM, Citrix XenServerTM and Citrix Presentation ServerTM are trademarks of Citrix®
Apple, Macintosh and Mac OS are registered trademarks of Apple Computer, Inc. Safari is a trademark of
Apple Computer, Inc.
Adobe, the Adobe logo, Acrobat and PostScript are either registered trademarks or trademarks of Adobe
Systems Incorporated in the United States and/or other countries.
Ethernet is a registered trademark of Xerox Corporation.
PCL is a registered trademark of Hewlett-Packard Company Limited.
CUPS and CUPS logo are registered trademark of Easy Software Products.
This machine and PageScope Box Operator are based in part on the work of the Independent JPEG Group.
Compact-VJE
Copyright 1986-2009 Yahoo Japan Corp.
RC4® is a registered trademark or trademark of EMC Corporation in the United States and/or other countries.
RSA and BSAFE are registered trademarks or trademarks of EMC Corporation in the United States and other
countries.
License information
[This product/Product name] includes RSA BSAFE Cryptographic software from EMC Corporation.
Advanced Wnn
"Advanced Wnn"© OMRON SOFTWARE CO., Ltd. 2006 All Rights Reserved.
ABBYY and FineReader are registered trade marks of ABBYY Software House.
Copyright © Extended Systems, Inc., 2000-2005.
Portions copyright ©iAnywhere Solutions, Inc.,
and Sybase, an SAP Company 2005-2012.
All rights reserved.
ThinPrint is a registered trademark or trademark of Cortado AG in Germany and other countries.

Trademark acknowledgements 1.10
1
Chapter 1
All other product and brand names are trademarks or registered trademarks of their respective companies or
organizations.
Copyright
Introduction
KONICA MINOLTA, INC. maintains the copyright of the printer drivers.

© 2013 KONICA MINOLTA, INC. All Rights Reserved.
Note
User's Guide may not be reproduced in part or in full without permission.
KONICA MINOLTA, INC. will not be held liable for any incidents caused by using this printing system or Us-
er's Guide.
Information included in User's Guide is subject to change without notice.

1.11 SOFTWARE LICENSE AGREEMENT
1
Chapter 1
1.11 SOFTWARE LICENSE AGREEMENT
This package contains the following materials provided by KONICA MINOLTA, INC. (KM): software included
as part of the printing system ("Printing Software"), the digitally-encoded machine-readable outline data en-
coded in the special format and in the encrypted form ("Font Programs"), other software which runs on a
Introduction
computer system for use in conjunction with the Printing Software ("Host Software"), and related explanatory
written materials ("Documentation"). The term "Software" shall be used to describe Printing Software, Font
Programs and/or Host Software and also include any upgrades, modified versions, additions, and copies of
the Software.
The Software is being licensed to you under the terms of this Agreement.
KM grants to you a non-exclusive sublicense to use the Software and Documentation, provided that you
agree to the following:
1. You may use the Software and accompanying Font Programs for imaging to the licensed output de-
vice(s), solely for your own internal business purposes.
2. In addition to the license for Font Programs set forth in Section 1 above, you may use Roman Font Pro-
grams to reproduce weights, styles, and versions of letters, numerals, characters and symbols ("Type-
faces") on the display or monitor for your own internal business purposes.
3. You may make one backup copy of the Host Software, provided your backup copy is not installed or
used on any computer. Notwithstanding the above restrictions, you may install the on any number of
computers solely for use with one or more printing systems running the Printing Software.
4. You may assign its rights under this Agreement to an assignee of all of Licensee's right and interest to
such Software and Documentation ("Assignee") provided you transfer to Assignee all copies of such
Software and Documentation Assignee agrees to be bound by all of the terms and conditions of this
Agreement.
5. You agree not to modify, adapt or translate the Software and Documentation.
6. You agree that you will not attempt to alter, disassemble, decrypt, reverse engineer or decompile the
Software.
7. Title to and ownership of the Software and Documentation and any reproductions thereof shall remain
with KM and its licensor.
8. Trademarks shall be used in accordance with accepted trademark practice, including identification of
the trademark owner's name. Trademarks can only be used to identify printed output produced by the
Software. Such use of any trademark does not give you any rights of ownership in that trademark.
9. You may not rent, lease, sublicense, lend or transfer versions or copies of the Software Licensee does
not use, or Software contained on any unused media, except as part of the permanent transfer of all
Software and Documentation as described above.
10. IN NO EVENT WILL KM OR ITS LICENSOR BE LIABLE TO YOU FOR ANY CONSEQUENTIAL, INCI-
DENTAL INDIRECT, PUNITIVE OR SPECIAL DAMAGES, INCLUDING ANY LOST PROFITS OR LOST
SAVING, EVEN IF KM HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY
CLAIM BY ANY THIRD PARTY. KM OR ITS LICENSOR DISCLAIMS ALL WARRANTIES WITH REGARD
TO THE SOFTWARE, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION IMPLIED WAR-
RANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE AND NON-IN-
FRINGEMENT OF THIRD PARTY RIGHTS. SOME STATES OR JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTIAL, CONSEQUENTIAL OR SPECIAL DAMAGES, SO THE
ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
11. Notice to Government End Users: The Software is a "commercial item," as that term is defined at 48
C.F.R.2.101, consisting of "commercial computer software" and "commercial computer software doc-
umentation," as such terms are used in 48 C.F.R. 12.212. Consistent with 48 C.F.R. 12.212 and 48
C.F.R. 227.7202-1 through 227.7202-4, all U.S. Government End Users acquire the Software with only
those rights set forth herein.
12. You agree that you will not export the Software in any form in violation of any applicable laws and reg-
ulations regarding export control of any countries.

i-Option LK-105 v3 (Searchable PDFs) End User License Agreement 1.12
1
Chapter 1
1.12 i-Option LK-105 v3 (Searchable PDFs) End User License Agree-

ment
Subject to your purchase of a license key of i-Option LK-105 v3 (searchable PDFs, or "Program"), KONICA
Introduction
MINOLTA, INC. (KM) grants you a non-exclusive and non-transferable sublicense to use the Program provid-
ed that you comply with all terms and conditions stated in this Agreement.
1. You agree not to reproduce, modify, or adapt the Program. You may not allow a third party to use the
Program or transfer it to a third party.
2. You agree that you will not attempt to alter, disassemble, decrypt, reverse engineer, or decompile the
Program.
3. KM or its licensor own the copyright and other intellectual property rights. No copyright or other intel-
lectual property rights shall be transferred to you through the granting to you of a license to use the
Program.
4. IN NO EVENT WILL KM OR ITS LICENSOR BE LIABLE TO YOU FOR ANY CONSEQUENTIAL, INCI-
DENTAL INDIRECT, PUNITIVE OR SPECIAL DAMAGES, INCLUDING ANY LOST PROFITS OR LOST
SAVING, EVEN IF KM HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY
CLAIM BY ANY THIRD PARTY. KM OR ITS LICENSOR DISCLAIMS ALL WARRANTIES WITH REGARD
TO THE PROGRAM, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION IMPLIED WARRAN-
TIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE AND NON-INFRINGE-
MENT OF THIRD PARTY RIGHTS. SOME STATES OR JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES, SO THE
ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
5. You agree that you will not export the Program in any form in violation of any applicable laws and reg-
ulations regarding export control of any countries.
6. Notice to Government End Users (this provision shall apply to U.S. government end users only) The Pro-
gram is a "commercial item," as that term is defined at 48 C.F.R.2.101, consisting of "commercial com-
puter software" and "commercial computer software documentation," as such terms are used in 48
C.F.R. 12.212. Consistent with 48 C.F.R. 12.212 and 48 C.F.R. 227.7202-1 through 227.7202-4, all U.S.
Government End Users acquire the Program with only those rights set forth herein.
7. This license shall automatically terminate upon a failure on your part to comply with any term or condi-
tion of this Agreement, in which case you agree to immediately stop use of the Program.
8. This Agreement shall be governed by the laws of Japan.

2
About This Machine
About This Machine Chapter 2

Introduction to User's Guide 2.1
2
2 About This Machine

Chapter 2
2.1 Introduction to User's Guide

The user's guide of this product consists of the booklet manual and the "User's Guide CD".
About This Machine
The booklet manual describe basic machine procedures and frequently asked questions.
If you want to learn about more detailed functions or operation methods, refer to the User's Guide included
in the "User's Guide CD".
In addition, you can access [Frequently Asked Questions] on the top page (home) of the relevant file on the
User's Guide CD for detailed information on FAQs and troubleshooting.
These user's guides should be stored in a safe place where you can access them easily.
2.1.1 Booklet manual
[Quick Start Guide]

This manual describes basic procedures users will need to know in
order to use this machine, as well as setting procedures. It also in-
troduces major functions, FAQs, and basic troubleshooting proce-
dures to make use of this machine more conveniently.
This manual also contains notes and precautions that should be fol-
lowed in order to use this machine. Please be sure to read this man-
ual before using this machine.

2
2.1.2 User's Guide CD
The "User's Guide CD" is provided with this machine.
Select a desired function on the top page (Home), and check the details of the function.
Chapter 2
Selecting [Introduction] on the top page (Home) allows you to view detailed methods for using the User's
Guide.
Layout of top page
About This Machine

1
2
No. Name Description

1 [Search by Function] Searches for desired information using functions such as printing or
scanning and buttons displayed on the touch panel.
2 [Search] Enter one or multiple keywords to search within the User's Guide.
(Some pages are not targeted for searching.)
3 [Search by Usage] Searches for the required operations of this machine based on the
request format of "wanting to do something". This function provides
security measures against various situations and methods to bring
about cost reductions.
4 [Search by Illustration] Searches for the required operations of this machine based on the
output result, functions, and operation images.

Introduction to User's Guide 2.1
2
Operating environment
Item Specifications
Chapter 2
Supported Operating Systems Windows XP (SP3), Windows Vista (SP2), Windows 7 (SP1)
Mac OS X10.4/10.5/10.6/10.7
Supported Web browsers Windows: Internet Explorer 6.x/7.x/8.x/9.x, Firefox 3.x/4.x/ESR 10.0
or later
Mac OS: Safari 3.1 or later /4.x/5.x
• We recommend that you use the latest Web browser that is com-
About This Machine
patible with your operating system to help you use this machine
more conveniently and comfortably.
• Check that JavaScript in your Web browser is enabled. The Us-
er's Guide uses JavaScript for the page display and search func-
tions.
• In Internet Explorer 6.x/7.x, it may take some time for a page to
display after you click a button or a menu in the table of contents.
Display resolution 1024 x 768 pixels or more
Viewing the top page

For Windows
- Windows XP opens the Web browser and displays the top page automatically when the User's Guide
CD is inserted into the CD-ROM drive of your computer.
- Windows Vista or Windows 7 displays a message related to automatic playing when the User's Guide
CD is inserted into the CD-ROM drive of your computer. Clicking [rundll32.exe] displays the top page.
- If the top page does not appear, select [My Computer] or [Computer], right-click on the
[Users_Guide_CD] icon, then click [Open]. If you double-click [index.html] in the folder, the top page will
open.
For Macintosh
- Double-click the CD icon on the desktop, then [index.html] to display the top page.
2.1.3 Symbols and Notations Used in This Manual
Procedural instruction
0 This check mark symbol shows a precondition of a procedure.
1 This format number "1" represents the first step.
2 This format number represents the order of serial steps.

% This symbol indicates a supplementary explanation of a procedural instruction.

2
Symbols and notations
7 WARNING
Chapter 2
- This symbol indicates that a failure to heed the instructions may lead to death or serious injury.
7 CAUTION
- This symbol indicates that negligence of the instructions may lead to mishandling that may cause injury
About This Machine

or property damage.
NOTICE
This symbol indicates a risk that may result in damage to this machine or documents.
Follow the instructions to avoid property damage.
Tips
- This symbol indicates supplemental information of a topic as well as options required to use a function.
d Reference
This symbol indicates that you should refer to the User's Guide CD for detailed information.
Notations Description
[] An item enclosed by brackets [ ] indicates a key name on the Touch Panel
or computer screen, or the name of a user's guide.
Bold text This presents a key name, part name, product name, or option name on
the Control Panel.
Notations of application names

This manual describes application names as shown below.
Application name Notations used in this manual

PageScope Web Connection Web Connection
PageScope My Panel Manager My Panel Manager

About this machine 2.2
2
2.2 About this machine
Chapter 2
2.2.1 Optional components (bizhub C554e/C454e)

Various optional components can be added to meet your office requirements.
About This Machine
32
31
30
29
3 4
28 27 26
2 1 5
6
25
7
24 8
23
9
10
22
11
21 12
20
14
13
19 18 17 16 15

2
1 Main unit Scans the original in the scanner section, and prints a scanned im-
age in the printer section.
Chapter 2
2 Fax Kit FK-511 Required to use the fax function.
3 Authentication Unit AU- Working Table WT-506 is required as a stand.
102 (Biometric Type)
4 Authentication Unit AU- Working Table WT-506 is required as a stand.
About This Machine

201 (IC Card Type)
5 Working Table WT-506 Provides an area to temporarily place an original or other materials.
This is also used when the Authentication Unit is installed.
6 Keypad KP-101 It is equipped on the side of the Control Panel. Allows you to enter
numbers by using the hardware keypad.
7 Keyboard Holder KH-102 Install this holder to use an external keyboard.
8 Security Kit SC-508 Supports functions such as Copy Guard to prevent unauthorized
copying.
9 Fax Mount Kit MK-728 This unit is required to install FAX Kit FK-508.
This option can be used in North America.
10 FAX Kit FK-508 Used to add telephone lines.
Fax Mount Kit MK-728 is required to install FAX Kit FK-508.
11 Mount Kit MK-730 Used to print on banner paper.
12 Large Capacity Unit LU- Allows you to load up to 3000 sheets of 8-1/2 e 11 (A4) size paper.
301
13 Large Capacity Unit LU- Allows you to load up to 2500 sheets of SRA3 or 11 e 17 (A3) size
204 paper.
14 Image Controller IC-414 Built-in Image Controller. Installing this unit provides higher quality
printing results.
15 Desk DK-510 Used to place this machine on the floor.
16 Paper Feed Cabinet PC- Can load up to 2500 sheets of 8-1/2 e 11 (A4) size paper.
410
17 Paper Feed Cabinet PC- Can load up to 500 sheets respectively into the top and bottom
210 trays.
18 Paper Feed Cabinet PC- Can load up to 500 sheets into the top tray. (The bottom tray is a
110 storage box.)
20 Saddle Stitcher SD-511 Used to add the bind/fold function to the Finisher FS-534.
21 Finisher FS-534 Sorts, groups, or staples output sheets as required.
22 Punch Kit PK-520 Used to add the punch function to the Finisher FS-534.
23 Saddle Stitcher SD-512 Used to add the bind/fold function to the Finisher FS-535 (only for
bizhub C554e).
24 Finisher FS-535 Sorts, groups, or staples output sheets as required (only for bizhub
C554e).
25 Punch Kit PK-521 Used to add the punch function to the Finisher FS-535 (only for bi-
zhub C554e).
26 Z Folding Unit ZU-606 Adds the Z-fold or punch function to the Finisher FS-535 (only for
bizhub C554e).
27 Job Separator JS-602 Feeds out printed sheets (only for bizhub C554e).
28 Post Inserter PI-505 Inserts a cover sheet into copied or printed sheets (only for bizhub
C554e).
29 Output Tray OT-506 Collects printed pages.
30 Finisher FS-533 Sorts, groups, or staples output sheets as required. This unit can be
installed in this machine.

2
32 Job Separator JS-506 Used to separate output sheets into two trays in the body of the ma-
chine.
Chapter 2
The following options are built into this machine and are not shown in the figure above.
33 Stamp Unit SP-501 Stamps a scanned original when sending a fax.
34 Spare TX Marker Stamp A replacement stamp for the Stamp Unit SP-501.
2
About This Machine
35 Local Interface Kit EK- Install this unit when using the voice guidance function.
606
36 Local Interface Kit EK- Install this unit when using the voice guidance function and the link-
607 age function with a Bluetooth-compatible device.
37 Video Interface Kit VI- This unit is required to install Image Controller IC-414.
506
38 i-Option LK-101 v3 Supports the web browser function that is one of the advanced
functions.
39 i-Option LK-102 v3 Supports the PDF processing function that is one of the advanced
functions.
40 i-Option LK-104 v3 Supports the voice guidance function that is one of the advanced
functions.
41 i-Option LK-105 v3 Supports the searchable PDF function that is one of the advanced
functions.
42 i-Option LK-106 Used to add a bar code font that is one of special fonts.
43 i-Option LK-107 Used to add a unicode font that is one of special fonts.
44 i-Option LK-108 Used to add an OCR font that is one of special fonts.
45 i-Option LK-110 Supports advanced functions such as a function that converts a file
into a DOCX or XLSX type, a function that generates highly-func-
tional and high quality data, and the E-mail RX Print function. For
details on the available functions, refer to the User's Guide CD.
46 i-Option LK-111 Supports the ThinPrint function that is one of the advanced func-
tions.
47 Upgrade Kit UK-204 Required when:
• Installing i-Option LK-101 v3/LK-102 v3/LK-104 v3/LK-105
v3/LK-106/LK-107/LK-108/LK-110;
• Using the My Address function in conjunction with My Panel
Manager; and
• Using the Overlay or Registered Overlay function.
48 Upgrade Kit UK-208 Used to return this machine from the Power Save mode via the
wireless network using an Android/iOS tablet terminal.
The following options are not shown in the figure.
49 Heater HT-509 Prevents paper in a paper tray from being affected by humidity.
Desk DK-510 or Paper Feed Cabinet is required to install this unit.
50 Power Supply BOX MK- Used to turn Heater operations on or off.
734
51 Mount Kit MK-735 Required to use the machine unit that has Authentication Unit AU-
201 (IC Card Type) built in to it.

2
2.2.2 Optional components (bizhub C364e/C284e/C224e)
Various optional components can be added to meet your office requirements.
Chapter 2
About This Machine
2 3 4
5 6 7
26
25
24
8
1 9
10
23 11
12
13
22
14
15
21
20 19 18 17 16

2
1 Main unit Scans the original in the scanner section, and prints a scanned im-
age in the printer section.
Chapter 2
2 Original Cover OC-511 Used to fix the loaded originals.

3 Reverse Automatic Doc- Automatically feeds and scans originals by page.
ument Feeder DF-624
4 Dual Scan Document Scans the front and back sides of the sheet at the same time. This
About This Machine
Feeder DF-701 enables higher-speed scanning.

5 Fax Kit FK-511 Required to use the fax function.
6 Authentication Unit AU- The Working Table WT-506 is required as a stand.
102 (Biometric Type)
7 Authentication Unit AU- The Working Table WT-506 is required as a stand.
201 (IC Card Type)
8 Working Table WT-506 Provides an area to temporarily place an original or other materials.
This is also used when the Authentication Unit is installed.
9 Keypad KP-101 It is equipped on the side of the Control Panel. Allows you to enter
numbers by using the hardware keypad.
10 Keyboard Holder KH-102 Install this holder to use an external keyboard.
11 Security Kit SC-508 Supports functions such as Copy Guard to prevent unauthorized
copying.
12 Fax Mount Kit MK-728 This unit is required to install FAX Kit FK-508.
13 FAX Kit FK-508 Used to add telephone lines.
Fax Mount Kit MK-728 is required to install FAX Kit FK-508.
14 Mount Kit MK-730 Used to print on banner paper.
15 Image Controller IC-414 External image controller. Installing this unit provides the higher-
quality printing result (only for bizhub C364e/C284e).
18 Paper Feed Cabinet PC- Can load up to 2500 sheets of 8-1/2 e 11 (A4) size paper.
410
19 Paper Feed Cabinet PC- Can load up to 500 sheets respectively into the top and bottom
210 trays.
20 Paper Feed Cabinet PC- Can load up to 500 sheets into the top tray. (The bottom tray is a
110 storage box.)
21 Finisher FS-534 Sorts, groups, or staples output sheets as required. The Desk DK-
510 or Paper Feed Cabinet is required to install this unit.
22 Saddle Stitcher SD-511 Used to add the bind/fold function to the Finisher FS-534.
24 Finisher FS-533 Sorts, groups, or staples output sheets as required. This unit can be
installed in this machine.
26 Job Separator JS-506 Used to separate output sheets into two trays in the body of the ma-
chine.
The following options are built into this machine and are not shown in the figure above.
27 Stamp Unit SP-501 Stamps a scanned original when sending a fax.
28 Spare TX Marker Stamp A replacement stamp for the Stamp Unit SP-501.
2
29 Local Interface Kit EK- Install this unit when using the voice guidance function.
606
30 Local Interface Kit EK- Install this unit when using the voice guidance function and the link-
607 age function with a Bluetooth-compatible device.

2
31 Video Interface Kit VI- This unit is required to install Image Controller IC-414 onto bizhub
506 C364e or bizhub C284e.
Chapter 2
32 i-Option LK-101 v3 Supports the web browser function that is one of the advanced
functions.
33 i-Option LK-102 v3 Supports the PDF processing function that is one of the advanced
functions.
34 i-Option LK-104 v3 Supports the voice guidance function that is one of the advanced
About This Machine

functions.
35 i-Option LK-105 v3 Supports the searchable PDF function that is one of the advanced
functions.
36 i-Option LK-106 Used to add a bar code font that is one of special fonts.
37 i-Option LK-107 Used to add a unicode font that is one of special fonts.
38 i-Option LK-108 Used to add an OCR font that is one of special fonts.
39 i-Option LK-110 Supports advanced functions such as a function that converts a file
into a DOCX or XLSX type, a function that generates highly-func-
tional and high quality data, and the E-mail RX Print function. For
details on the available functions, refer to the User's Guide CD.
40 i-Option LK-111 Supports the ThinPrint function that is one of the advanced func-
tions.
41 Upgrade Kit UK-204 Required when:
• Installing i-Option LK-101 v3/LK-102 v3/LK-104 v3/LK-105
v3/LK-106/LK-107/LK-108/LK-110;
• Using the My Address function in conjunction with My Panel
Manager; and
• Using the Overlay or Registered Overlay function.
42 Upgrade Kit UK-208 Used to return this machine from the Power Save mode via the
wireless network using an Android/iOS tablet terminal.
• If you are using Reverse Automatic Document Feeder, Up-
grade Kit UK-209 is required to connect an Android/iOS tablet
terminal to this machine.
• If you are using Dual Scan Document Feeder, Upgrade Kit
UK-209 (dual scan board) is already installed on this machine.
43 Upgrade Kit UK-209 Used to connect an Android/iOS tablet terminal to this machine and
display the Control Panel on the Android/iOS tablet terminal, ena-
bling remote-control operations.
• This unit is required when using Reverse Automatic Document
Feeder.
• If you are using Dual Scan Document Feeder, Upgrade Kit
UK-209 (dual scan board) is already installed on this machine.
The following options are not shown in the figure.
44 Heater HT-509 Prevents paper in a paper tray from being affected by humidity.
Desk DK-510 or Paper Feed Cabinet is required to install this unit.
45 Power Supply BOX MK- Used to turn Heater operations on or off.
734
46 Mount Kit MK-735 Required to install Authentication Unit AU-201 (IC Card Type).

2
2.2.3 Name of parts (MFP) (bizhub C554e/C454e)
Front side
Chapter 2
The illustration shows the main unit that contains the Output Tray and Paper Feed Cabinet.
1 2
About This Machine
11
10
3
9
6
4

1 Control Panel Use the Touch Panel or buttons on this panel to operate this ma-
chine.
2 Original Tray Load the original.
3 Stylus Pen Used to operate the Touch Panel.
4 Bypass Tray Used to load custom-size paper or special paper.
5 Paper-Empty Indicator Flashes orange when a tray runs low on paper and lights up orange
when the tray runs out of paper.
6 Paper Tray Used to load standard-size paper.
7 Lower Front Door Open this door to replace consumables or to maintenance this ma-
chine.
8 Upper Front Door Open this door to replace a Toner Cartridge.
9 Data Indicator Flashes blue while this machine is receiving a job. If a job is current-
ly spooled, this indicator lamp lights up blue.
10 Status Indicator Flashes white during printing.
11 Warning Indicator Flashes orange if a warning occurs. Lights up orange if this machine
has stopped due to an error.

2
Rear side
The illustration shows the main unit that contains the Paper Feed Cabinet, Fax Kit FK-511, FAX Kit FK-508,
Fax Mount Kit, and Power Supply BOX.
Chapter 2
(FAX Kit FK-508 and Fax Mount Kit can be used in North America.)
About This Machine

2
8
7
5
4
6
No. Name
1 Telephone Jack 1/2 (LINE PORT1/2)
2 Jack for connecting a telephone (TEL PORT1/2)
3 Power Cord
4 Heater Power Switch
5 Telephone Jack 3/4 (FAX3/4)
6 USB Port (Type A) USB2.0/1.1
7 Network Connector (10Base-T/100Base-TX/1000Base-T)
8 USB Port (Type B) USB2.0/1.1
d Reference
For details, refer to the User's Guide CD.

2
2.2.4 Name of parts (MFP) (bizhub C364e/C284e/C224e)
Front side
Chapter 2
The illustration shows the main unit that contains the Reverse Automatic Document Feeder and Paper
Feed Cabinet.
1 2
About This Machine
10
9 3
6
4

1 Control Panel Use the Touch Panel or buttons on this panel to operate this ma-
chine.
2 Original Tray Load the original.
3 Stylus Pen Used to operate the Touch Panel.
4 Bypass Tray Used to load custom-size paper or special paper.
5 Paper-Empty Indicator Flashes orange when a tray runs low on paper and lights up orange
when the tray runs out of paper.
6 Paper Tray Used to load standard-size paper.
7 Front Door Open this door to replace consumables or to maintenance this ma-
chine.
8 Data Indicator Flashes blue while this machine is receiving a job. If a job is current-
ly spooled, this indicator lamp lights up blue.
9 Status Indicator Flashes white during printing.
10 Warning Indicator Flashes orange if a warning occurs. Lights up orange if this machine
has stopped due to an error.

2
Rear side
The illustration shows the main unit that contains the Reverse Automatic Document Feeder, Paper Feed
Cabinet, Fax Kit FK-511, FAX Kit FK-508, Fax Mount Kit, and Power Supply BOX.
Chapter 2
(FAX Kit FK-508 and Fax Mount Kit can be used in North America.)
About This Machine

2
8
7
5
4
6
No. Name
1 Telephone Jack 1/2 (LINE PORT1/2)
2 Jack for connecting a telephone (TEL PORT1/2)
3 Power Cord
4 Heater Power Switch
5 Telephone Jack 3/4 (FAX3/4)
6 USB Port (Type A) USB2.0/1.1
7 Network Connector (10Base-T/100Base-TX/1000Base-T)
8 USB Port (Type B) USB2.0/1.1
d Reference

2
2.2.5 Name of parts (Optional units)
This section shows the names of distinctive parts for each optional unit that can be installed in this machine.
Chapter 2
Finisher FS-535, Saddle Stitcher SD-512, Punch Kit PK-521 (bizhub C554e)
1
About This Machine
No. Name
1 Output Tray
2 Punch Kit
3 Punch Scrap Box
4 Staple Cartridge
5 Saddle Stitcher

2
Chapter 2
About This Machine
2
No. Name
1 Staple Cartridge
2 Folding Output Tray

2
Job Separator JS-602 (bizhub C554e)
1
Chapter 2
About This Machine
No. Name
1 Output Tray

2
Z Folding Unit ZU-606 (bizhub C554e)
Chapter 2
1
About This Machine

2
No. Name
1 Z Folding/Conveyance Unit
2 Punch Scrap Box

2
Post Inserter PI-505 (bizhub C554e)
Chapter 2
About This Machine
3
2
No. Name
1 Lower Tray
2 Upper Tray
3 Post Inserter Control Panel
d Reference
For details on how to use the Post Inserter Control Panel, refer to the User's Guide CD.

2
Finisher FS-533, Punch Kit PK-519
Chapter 2
About This Machine
4
1 2
No. Name
1 Staple Cartridge
2 Punch Kit
3 Output Tray
4 Tray Extension

2
Job Separator JS-506
Chapter 2
About This Machine
No. Name
1 Output Tray

2
Finisher FS-534, Saddle Stitcher SD-511, Punch Kit PK-520
Chapter 2
1
About This Machine

2
3
No. Name
1 Output Tray
2 Punch Scrap Box
3 Staple Cartridge
4 Saddle Stitcher

2
Chapter 2
1
About This Machine
No. Name
1 Punch Kit
2 Staple Cartridge
3 Folding Output Tray

2
Large Capacity Unit LU-301/LU-204
Chapter 2
About This Machine
d Reference

Power supply 2.3
2
2.3 Power supply
This machine provides two power switches: Power key on the Control Panel and Main Power Switch on
the machine. Under normal conditions, operate the Power key of the control panel. Use Main Power
Chapter 2
Switch to restart this machine.
2.3.1 Turning the power on and off

Turn the power on and off only when necessary, for example, when the administrative settings are changed
About This Machine
or a power failure occurs.
1 Open the Lower Front Door or Front Door, and turn the Main
Power Switch on.
2 Turn the Main Power Switch off.
NOTICE
To restart this machine, turn the Main Power Switch off and on again after 10 or more seconds have passed.

2.3 Power supply
2
2.3.2 Operating the Power key
To immediately shift to the power save mode, for example, when work is finished or when not operating this
machine for a long period of time, press the Power key.
Chapter 2
The machine shifts to different power save modes depending on how long the Power key is pressed.
Pressing the Power key briefly during operation shifts to the low power or sleep mode. Holding down the
Power key shifts to the Sub Power OFF mode.
To return this machine from the power save mode to the normal mode, press the Power key again.
About This Machine

In the low power or sleep mode, you can return this machine from the power save mode to the normal mode
simply by placing your hand close to the Control Panel.
Status of this machine Description

Power Save Low Power or Flashes blue.
mode Sleep mode This machine returns to the normal mode when data or faxes are re-
ceived.
Sub Power Lights up orange.
OFF mode This machine can receive data or faxes, but cannot scan or print an
original. If data or faxes are received when the machine is in the Sub
Power OFF mode, they are printed when the machine returns to the
normal mode.
Normal mode During oper- Lights up blue.
ation
2.3.3 Power save function

If the specified time (default: 15 minutes) elapses after the machine becomes inactive, the machine automat-
ically shifts to the power save mode; for example, the touch panel display is turned off. The Power key flashes
blue in the power save mode. The power save mode returns to the normal mode by pressing any key on the
Control Panel for instance.
There are two power save modes: the low power mode and the sleep mode. Sleep mode provides a greater
power saving effect than Low Power mode. However, the time required to return to Normal mode is longer
than the time required to revert to Low Power mode.
d Reference
The time required to shift to each mode can be changed in the Administrator Settings. For details, refer to the
User's Guide CD.

Power supply 2.3
2
Reducing power consumption
To reduce power consumption in the standby state, change [Power Key Setting] to [Sub Power OFF].
Tap [Utility], and select [Administrator Settings] - [System Settings] - [Power Supply/Power Save Settings] -
Chapter 2
[Power Key Setting].

For information on the default administrator password, refer to page 5-51.
About This Machine
After the setting is changed, the power save mode shifts as shown below depending on how the Power key
is pressed.
- Pressing the Power key
– This machine shifts to the Sub Power OFF mode.
– In the Sub Power OFF mode, the machine can receive data or faxes, but cannot scan or print an original.
– If data or faxes are received when the machine is in the Sub Power OFF mode, they are printed when
the machine returns to the normal mode.
- Holding down the Power key
– This machine shifts to the ErP Auto Power OFF mode.
– In the ErP Auto Power OFF mode, this machine cannot receive data or faxes and also cannot scan or
print an original.
– This function provides a greater power saving effect than the Sub Power OFF mode, which is close to
the state where the main power is turned off.
To enable the machine to return to the normal mode from the Sub Power OFF or ErP Auto Power OFF mode,
press the Power key again.
d Reference

2.4 Control Panel
2
2.4 Control Panel
The Keypad KP-101 is equipped on the right side of the Control Panel.
Chapter 2
2.4.1 Name of parts
About This Machine

13 2
3
4
5
6
7
12 11 10 9 8

1 Touch Panel Various screens and messages are displayed. Directly touch the
Touch panel to configure each setting.
2 [Menu] Tap this button to display the main menu.
3 [Enlarge Display] Enters Enlarge Display mode.
4 [Guidance] Tap this button to display the Help Menu. You can display descrip-
tions of the functions and operating procedures on the screen.
5 [Access] If user authentication or account track is enabled, enter the user
name and password for user authentication or the account name
and password for account track, then tap this button to start the use
of this machine. After a target operation is completed, tap this but-
ton once again to end the use of this machine.
6 [Interrupt] Tap this button to enter the Interrupt mode. The indicator lamp
lights up blue in the Interrupt mode. To cancel the Interrupt mode,
tap [Interrupt] again.
7 [Preview] Tap this button to print a single proof copy to be checked before
printing a large number of copies. This function can also display a
finishing image with the current settings on the Touch Panel.
8 Reset Press this key to reset all settings, excluding the registered ones,
that you entered using the Control Panel.
9 Stop Press this key to temporarily stop an active copy, scan, or print job.
10 Start Press to start the copy, scan or fax operation.
11 Register key Press each key to switch the display of the Touch Panel to a func-
tion assigned to a Register key.
• 1 (Scan/Fax): Switches to the scan/fax function.
• 2 (Copy): Switches to the copy function.
• 10Keypad (10 Keypad): Displays the keypad on the Touch pan-
el.
The Register key can be assigned to any function in the Adminis-
trator Settings to be easy to use.

Control Panel 2.4
2
12 Power Press this key to switch to the power save mode.
In the normal mode, the key lights up blue. In the power save mode,
Chapter 2
the key blinks blue or lights up orange.

To create a higher power saving effect, you can change the setting
in [Power Key Setting] of Administrator Settings. For [Power Key
Setting], refer to page 2-28.
13 Warning Indicator Flashes orange if a warning occurs.
Lights up orange if this machine has stopped due to an error.
About This Machine
Equipped with the Keypad KP-101

1 Voice Guide Press this key to start the voice guidance function (optional).
2 Keypad Use this keypad to enter numeric values such as the number of cop-
ies, zoom ratio, and fax number.
3 C Press this key to cancel numeric values such as the number of cop-
ies, zoom ratio, and size you entered using the keypad.

2.5 Touch Panel
2
2.5 Touch Panel
Chapter 2
2.5.1 Main Menu
Tap [Menu] on the Control Panel to display the main menu. In the main menu, you can configure settings
such as frequently used functions or a shortcut key for jumping to each mode.
Layout of main menu
About This Machine

1

1 [Accessibility] Tap this button to adjust a Touch Panel pressing position, change
keying sounds, and configure the operating environment of the
Control Panel.
[Counter] Tap this button to display the total number of pages printed on this
machine on a function or color basis.
[Job List] Tap this button to display active or standby jobs. If necessary, you
can view job logs or print a communication report. For details, refer
to page 2-38.
2 Main menu keys Display shortcut keys assigned to any function.
By default, the main menu shows [Copy], [Scan/Fax], [User Box],
[Sound Setting], and [Utility].
[Utility] Tap this button to configure settings of this machine or view the use
status of this machine.
• [Utility] is always displayed.

Touch Panel 2.5
2
Customizing the main menu
The main menu can be extended to three screens as necessary. Up to 25 keys can be assigned to three main
menu screens which can be switched.
Chapter 2
About This Machine
In addition, you can specify your favorite background pattern.
d Reference
2.5.2 Operating the Touch Panel

The Touch Panel of this machine supports user-friendly operations, such as, sliding a finger on the Touch
Panel.
Tap
Lightly touch the screen with your finger, then remove your finger
from the screen immediately. This action can select or determine a
menu.
Double-tap
Lightly touch the screen with your finger twice in succession. Used
to retrieve detailed information, to enlarge a thumbnail or preview
image, and to open a User Box.

2.5 Touch Panel
2
Flick
Make a slight fillip while sliding your finger on the screen. Used to
scroll the destination/job list or to feed a page in the Main menu
Chapter 2
screen/Preview screen.
About This Machine

Drag
To move the scroll bar or document, place your finger on it and
move your finger. Used to move the scroll bar or document.
Pan
Slide your finger parallel in a front-to-back and side-to-side direc-
tion on the screen. Used to move to the intended display location if
data spans multiple screens.
Long-tap
Hold down the document by the finger. Used to display the icon re-
lated to the document.

Touch Panel 2.5
2
Drag & Drop
Slide your finger to the intended place and release it while a docu-
ment is selected. Used to move the document to the intended place.
Chapter 2
About This Machine
Pinch in/Pinch out

Place two fingers on the screen and then open or close them. Used
to enlarge or reduce a preview image.
Rotation
Place two fingers on the screen and then rotate them. Used to rotate
a preview image.

2.5 Touch Panel
2
Precautions on using the Touch panel
This machine features a capacitance-base touch panel. Note the following points when operating the Touch
Panel.
Chapter 2
- Use your finger or the Stylus Pen supplied with this machine. Note that the Touch Panel will not re-
spond appropriately if you operate it using your nail or a pen tip instead of your finger or the Stylus Pen.
- Applying a strong force to the Touch Panel will damage the Touch Panel, and potentially cause a
breakage.
- When operating in the Touch Panel, do not press on it using excessive force or with a pointed object
About This Machine

such as a mechanical pencil.
- The Touch Panel may not respond appropriately, if operated with a wet finger.
- The Touch Panel will not respond appropriately, if operated with hands with gloves on. It is recom-
mended that you use the Stylus Pen supplied with this machine or your finger.
- The Touch Panel may not respond appropriately, if the distance between you and a fluorescent lamp
is 20 inches (50 cm) or less while you are operating the Touch Panel.
- Avoid using the Touch Panel at a site near a device that generates electric noise (such as a generator
and an air conditioner). The electric noise may cause the Touch Panel to operate erratically.

Touch Panel 2.5
2
2.5.3 How to display the keypad
When tapping the input area on the copy screen and etc. for entering the number of copies or entering ad-
justment values, the keypad will be displayed.
Chapter 2
It can also be displayed by pressing the 10keypad provided for the Register key.
Input area for entering the number of copies

About This Machine
Input area for entering values
How to move the keypad

Move your finger while the upper side of keypad is being pressed.
How to close the keypad

After entering, tap [Close] to close the keypad.
It can also be closed by pressing the 10keypad provided for the
Register key.

2.5 Touch Panel
2
To display the keypad all the time
The keypad can be displayed all the time on the copy screen, print setting screen for boxes or browser.
Chapter 2
d Reference
2.5.4 Entering characters
About This Machine

When entering characters to register an address or program, use the keyboard screen displayed on the
Touch Panel.
When typing in "Group1":

1 To type in uppercase letters or symbols, tap the [Shift] key.
% If you mistyped, tap [ ] or [ ] to move the cursor to the character you want to clear, then tap the
[Delete] key.
% Tap the [Shift] key again to return to the original keyboard screen.
2 After typing completes, tap [OK].

Jobs 2.6
2
2.6 Jobs
Chapter 2
2.6.1 Job screen

A job refers to an operation such as printing, sending, receiving, or saving.
When you tap [Job List] in the main menu or the main screen of each mode, the Job screen appears.
In the Job screen, you can view a list or history of a job currently being executed or print a sending-receiving
result report.
About This Machine
In general, jobs are executed starting from the job at the top of the list of currently active jobs. If you are in a
hurry to execute any particular jobs, you can rearrange the job execution order.
1 2
3
4
5
No. Description
1 Displays jobs.
2 Select a job type. In [Comm. List], you can also print a sending-receiving result report.
3 Tap this button to narrow down the jobs to be displayed.
4 Tap this button to delete a job.
5 Tap this button to select a job to be executed preferentially.
6 Tap this button to view details of a selected job.
2.6.2 Multi-job function

While a job is active, you can register another job. Up to 251 jobs can be registered in total.
The table below shows the maximum number of jobs that can be registered for each function.
Function Minimum number of jobs Maximum number of jobs

Copy 5 61
Print 10 66
Scan 5 61
Fax memory TX 50 106
Fax RX 100 156
Sharing 56 -
These values may vary depending on conditions.
d Reference

2.7 Loading Paper
2
2.7 Loading Paper
Chapter 2
2.7.1 Loading paper in Tray 1 to Tray 4
Up to 500 sheets of plain paper can be loaded into each tray. Tray3 and Tray4 are optional.
Applicable paper types
About This Machine

Plain paper, single-side-only paper, thin paper, special paper, thick paper, letterhead, colored paper, and re-
cycled paper
How to load paper

1 Pull out the tray.
NOTICE
Be careful not to touch the Film.
2 Slide the Lateral Guide to fit the size of the paper to be load-
ed.
3 Load paper into the tray.

% Load paper into the tray with the print side facing up.
4 When loading paper other than plain paper, specify the paper type. For details, refer to page 2-42.

Loading Paper 2.7
2
2.7.2 LCT (built-in)
Up to 2500 sheets of plain paper can be loaded into the LCT (built-in). The LCT (built-in) is an option.
Chapter 2

Plain paper, single-side-only paper, thin paper, special paper, thick paper, letterhead, colored paper, and re-
cycled paper
About This Machine
How to load paper

1 Pull out the tray.
NOTICE
Be careful not to touch the Film.
2 Load paper into the right tray.

NOTICE
Do not load the tray with paper of a size other than that previ-
ously specified. To change the paper size, contact your serv-
ice representative.
3 Load paper into the left tray.


2.7 Loading Paper
2
2.7.3 Loading paper into the Large Capacity Unit
Up to 3000 sheets of plain paper can be loaded into Large Capacity Unit LU-301, and up to 2500 sheets of
plain paper into Large Capacity Unit LU-204.
Chapter 2
The Large Capacity Unit is an option.

Plain paper, single-side-only paper, thin paper, special paper, thick paper, letterhead, colored paper, recy-
About This Machine

cled paper
How to load paper

1 Open the door.
2 Lift the Paper Feed Roller, and load paper into the unit.
% Load paper into the tray with the print side facing down.
NOTICE
Exercise care not to touch the surface of the Paper Feed Roll-
er with your hand.
Do not load the Large Capacity Unit with paper of a size other
than that previously specified. To change the paper size, con-
tact your service representative.

Loading Paper 2.7
2
2.7.4 Bypass Tray
Use the Bypass Tray when printing on a paper size other than for paper trays, or printing on envelopes or
transparencies.
Chapter 2
To use the Bypass Tray, load paper and specify the paper type.

Plain paper, single-side-only paper, special paper, thick paper, postcard (4 e 6 (A6 Card)), transparency, let-
About This Machine
terhead, colored paper, envelope, label sheets, index paper, recycled paper, and banner paper
Applicable paper sizes

Type Size
Standard-size paper 12 e 18 w to 5-1/2 e 8-1/2 w/v, 4 e 6 w, SRA3 w, A3 w to A6 w, B4 w to
B6 w, A6 card w, 8 e 13 w, 16K w/v, 8K w, banner paper
Custom-size paper Paper width: 3-9/16 to 12-5/8 inches (90 mm to 320 mm)
Paper length: 5-1/2 to 47-1/4 inches (139.7 mm to 1,200 mm)
How to load paper

1 Open the tray.
% To load large-sized paper, pull out the Tray Extension.
% To load banner paper, install the Mount Kit MK-730 for
banner paper.
NOTICE
Exercise care not to touch the surface of the Paper Feed Roll-
er with your hands.
2 After loading paper, adjust the Lateral Guide.

% Load paper into the tray with the print side facing down.

2.7 Loading Paper
2
3 Specify the paper type. Tap [Paper].
Chapter 2
About This Machine
4 Select [#], then tap [Change Tray Setting].
1 2
5 Select the paper type.
6 Specify the paper size.

Loading Paper 2.7
2
Chapter 2
1
About This Machine
% For Auto Detect

[Auto Detect] detects the paper size automatically when standard-size paper is loaded into a tray.
% For Standard Size

[Standard Size] is available when loading a postcard or standard-size paper for overseas.

2.7 Loading Paper
2
% For Custom Size
Chapter 2
2
About This Machine

3
% For Wide Paper
2
3

Loading Paper 2.7
2
Chapter 2
About This Machine

3
Operations
Basic Settings and
Basic Settings and Operations Chapter 3

Print Function 3.1
3
3 Basic Settings and Operations
3.1 Print Function

Chapter 3
3.1.1 Required settings and basic operations (For Windows OS)

Print data created on your computer via the network.
This section describes how to configure standard print settings using the installer.
Basic Settings and Operations
Preparation flow
The following describes a preparation flow to print data. For details, refer to the relevant page.
This preparation is not required the second time or subsequent times.
1 Checking the cable connection (Administrator)

% Check that this machine is correctly connected to the network cable. For details, refer to page 3-3.
2 Checking network settings of this machine (Administrator)

% Check the network settings of this machine. For details, refer to page 3-3.
The network can be used with the default settings unless otherwise requested.
3 Installing the printer driver

% Install the printer driver on the computer. For details, refer to page 3-4.
Operation flow
The following describes a flow to print data from your computer. For details, refer to page 3-7.
1 Opening original data

% Open the data you want to print using the application software.
2 Configuring the printer driver for printing

% Select a printer driver, and change the setting if necessary before printing.

3.1 Print Function
3
Checking the cable connection
Check that a LAN cable is connected to the LAN port of this ma-
chine and the green LED is on.
Chapter 3
Checking network settings of this machine
Tap [Utility], and select [Device Information]. Check that the IP address is displayed.
• For IPv4 environment • For IPv6 environment
Tips
- In general, the default settings are available for network connection; however, some network environ-
ments require a change on network settings.
- If no IP address is displayed, you need to configure the network. Tap [Utility], and select [Administrator
Settings] - [Network Settings] - [TCP/IP Settings]. Configure the required settings to suit your environ-
ment. For details, refer to the User's Guide CD.
- For information on the default administrator password, refer to page 5-51.

Print Function 3.1
3
Installing the printer driver
Use the installer to install the printer driver.
0 This operation requires administrator privileges for your computer.
1 Insert the printer driver CD-ROM into the CD-ROM drive of the
computer.
Chapter 3
2 Click [Printer Install].
3 Proceed with the procedure according to the on-screen instructions.
This automatically searches for the appropriate network and displays printers and MFPs that are com-
patible with the printer driver.

3.1 Print Function
3
4 Select this machine from the list.
% If multiple identical models are displayed, check the IP address to select an appropriate one. For
details on how to check the IP address of this machine, refer to page 3-3.
Chapter 3
1

2
5 Select the check boxes of the printer drivers to be installed.
6 Click [Install].

Print Function 3.1
3
7 Click [Finish].
Chapter 3

3.1 Print Function
3
Printing data
1 Open the data you want to print using the application software.
2 In the [File] menu, click [Print].
Chapter 3
3 Select the installed printer driver, and click [Print].
Tips
- Clicking [Preferences] can change the setting of the printer driver as required.
- If user authentication is enabled in this machine, specify the required data such as the user name and
password.

Print Function 3.1
3
Types of printer drivers
Select a printer driver that will meet your printing requirements.
Driver type Description

PCL This is a standard driver for printing general office documents. Among the three
drivers, this driver provides the fastest printing speed.
PS This driver is effective to exactly print data that is created using PostScript-com-
Chapter 3
patible application software from Adobe or other vendors. This driver is often used
in graphics and light printing applications where good color reproducibility is im-
portant.
XPS Developed after Windows Vista, this driver supports XML Paper Specification
(XPS). This driver has several advantages, including high-quality reproduction of
translucence.

3.1 Print Function
3
3.1.2 Required settings and basic operations (For Mac OS)
Print data created on your computer via the network.
This section describes how to configure a printer driver, for the OS X 10.6 environment, Bonjour connection,
and use of metric-size paper as major conditions.
Chapter 3
Preparation flow
The following describes a preparation flow to print data. For details, refer to the relevant page.


3 Installing the printer driver

% Install the printer driver on the computer. For details, refer to page 3-12.
4 Adding and configuring a printer driver

% Set up your computer so that data can be printed using the installed printer driver. For details, refer
to page 3-15.
Operation flow
The following describes a flow to print data from your computer. For details, refer to page 3-17.
1 Opening original data

% Open the data you want to print using the application software.
2 Configuring the printer driver for printing

% Select a printer driver, and change the setting if necessary before printing.

Print Function 3.1
3
Chapter 3

1 Tap [Utility], and select [Device Information]. Check that the IP address is displayed.
2 Specify the Bonjour name. Tap [Utility], and select [Administrator Settings] - [Network Settings] - [Bon-
jour Setting] - [ON].
% For information on the default administrator password, refer to page 5-51.

3.1 Print Function
3
% The Bonjour name is displayed on the printer driver as a connected device name. For "bizhub C364e
(5A:0C:4B)", "bizhub C364e" indicates the product name, and "(5A:0C:4B)" indicates the last three
bytes of the MAC address.
Chapter 3
2

3
% To change the Bonjour name, tap [Bonjour Name], and enter the name using the displayed key-
board.
Tips
- If no IP address is displayed in Step 1, you need to set up the network. Tap [Utility], and select [Admin-
istrator Settings] - [Network Settings] - [TCP/IP Settings]. Configure the required settings to suit your
environment. For details, refer to the User's Guide CD.

Print Function 3.1
3
Installing the printer driver
Use the installer to install the printer driver.
computer.
Chapter 3
2 Select the target printer driver, and copy it to the desktop.

Example: /Driver/OS_10_6_x/Letter/bizhub_C364_106.pkg
(Printer driver for OS X 10.6)
% When ordinarily using metric-sized paper, select a printer
driver in the "A4" directory.
% The last three digits of the printer driver name indicate the
version of the operating system.
3 Double-click the file copied onto the desktop.
4 Proceed with the procedure according to the on-screen instructions until the installation screen ap-
pears.

3.1 Print Function
3
Chapter 3

Print Function 3.1
3
5 Click [Install].
Chapter 3
6 When a prompt message appears to ask you to enter the name and password, type in the name and
password of the user with administrator privileges.
7 Click [Close].

3.1 Print Function
3
Adding and configuring a printer driver
Set up your computer so that data can be printed using the installed printer driver.
1 In the Apple Menu, click [System Preferences] - [Print & Fax].
2 Click [+].
Chapter 3
This automatically searches for the appropriate network and displays printers and MFPs that are com-
patible with the printer driver.
3 Select a printer for the Bonjour connection. Search for this machine from the list of printers for which
[Kind] is set to [Bonjour], and click it.
% If you cannot identify the connected machine because multiple same product names are listed,
check with the administrator.
This automatically searches for a printer driver compatible with the selected printer.

Print Function 3.1
3
4 Check that the printer driver is displayed.
Chapter 3
5 Select the installed optional units.

3.1 Print Function
3
Printing data
1 Open the data you want to print using the application software.
2 From the [File] menu, select [Print].
Chapter 3
3 Select the Bonjour name of this machine.
Tips
- If necessary, you can change the settings of the printer driver.

Scan-to-Send function 3.2
3
3.2 Scan-to-Send function
3.2.1 Various transmission methods

The original data scanned by this machine can be sent and saved using a variety of methods.
Sending data to your computer (SMB Send)

Chapter 3
Send scanned data to a computer on the network. Once settings are configured, you can send data easily.
For details, refer to page 3-20 and page 3-30.
Transmitting data as E-mail attachment (E-mail TX)

Send scanned data as an E-mail attachment. This function is useful when you want to forward data to an
outside location. For details, refer to page 3-40.
Saving data to the USB memory device (External memory)

Directly save scanned data on the USB memory device connected to this machine. For details, refer to
page 3-77.

3
Various methods for transmitting and saving data
In addition to the above, data can be sent and saved in various methods. Select the appropriate one to meet
your needs.
- Issuing a scan instruction from a computer (Web service function)
- Saving data to a User Box on the HDD (Save in User Box)
- Sending to an FTP server (FTP TX)
- Sending to a WebDAV server (WebDAV Send)
Chapter 3
d Reference

3
3.2.2 Sending data to your Windows computer (SMB Send)
Send scanned data to a computer on the network.
Once settings are configured, you can send data easily.
Chapter 3
Preparation flow
The following describes a preparation flow for sending scanned data. For details, refer to the relevant page.


3 Checking computer information

% Check the information required for Store Address, and fill out the checklist. For details, refer to
page 3-22.
4 Configuring your computer

% Configure settings to share a computer, or create a dedicated folder to receive files. For details, refer
to page 3-23.
5 Registering destinations
% Register destinations to which files are sent while checking the checklist. For details, refer to
page 3-26.
Operation flow
The following describes a transmission flow. For details, refer to page 3-28.
1 Loading the original
2 Selecting a destination
% Select a registered destination, and check the settings such as the file type and image quality.
3 Press the Start key.

% Press the Start key to scan the original.

3
Chapter 3
Tap [Utility], and select [Device Information]. Then, check that the IP address is displayed.
Tips

3
Checklist
While making notes in the checklist shown below, check computer information and configure settings for
preparation. The completed checklist is used for Store Address.
Name Entry column Detail

Host Address Host name or IP address to which the scanned data is sent page 3-22
Chapter 3
File Path Name of the dedicated folder to receive the scanned data page 3-23
User ID User name required to log in to the computer page 3-22

Password Password required to log in to the computer Contact your sys-

• You should not enter this column for security reasons. tem administra-
tor.
Checking computer information

Check the host address and user ID, and write them down.
1 Display the Properties window of the computer.

% In Windows 8, right-click on the Start window, then select [All apps] - [Computer]. On the toolbar,
select [Computer] - [System properties].
% In Windows Vista/7, from the Start menu, select [Computer] - [System properties].
% In Windows XP, open the Start menu, and right-click on [My Computer], and select [Properties].
2 Check the computer name, and write it down in the Host address column of the checklist.
3 Open the command prompt.

% In Windows 8, right-click on the Start window, then select [All apps] - [Command Prompt].
% In Windows Vista/7, from the Start menu, select [All Programs] - [Accessories] - [Command Prompt].
% In Windows XP, open the Start menu, and select [Programs] - [Accessories] - [Command Prompt].

3
4 Check the user name, and write it down in the User ID column of the checklist.
% In the example shown below, "taro.yamada" is displayed as the user ID.
Chapter 3
Configuring your computer
Create a new folder, and enable the sharing settings.
1 Display the Network and Sharing Center window to configure a sharing setting.
% In Windows 8, right-click on the Start window, select [All apps] - [Control Panel] - [Network and In-
ternet] - [Network and Sharing Center] - [Change advanced sharing settings], then select the [Turn
on file and printer sharing] check box.
% In Windows 7, from the Start menu, select [Control Panel] - [Network and Internet] - [Network and
Sharing Center] - [Change advanced sharing settings] then select the [Turn on file and printer shar-
ing] check box.

3
% In Windows Vista, open the Start menu, select [Control Panel] - [Network and Sharing Center], then
turn on [File sharing].
Chapter 3
% For Windows XP, the control panel setting is not required.
2 Create a new folder, and write down the folder name in the File path column of the checklist.
3 Only for Windows XP, check the folder options.

% Double-click the folder, select [Tools] - [Folder Options...] then click the [View] tab.
% Clear the [Use simple file sharing (Recommended)] check box.

3
4 Configure the setting to share the folder created in Step 2. Right-click on the folder, then click [Proper-
ties].
% For Windows XP, right-click on the folder, then click [Sharing and Security].
Chapter 3
5 Click the [Sharing] tab, then click [Advanced Sharing].
% For Windows XP, [Advanced Sharing] does not appear.

6 Select the [Share this folder] check box, then click [Permissions].
7 Select [Everyone] from the [Group or user names:] list, then select all of the [Allow] check boxes.

3
Registering destinations
While checking the created checklist, register the folder for receiving the scanned data as an address book
of this machine.
1 Tap [Utility], and select [One-Touch/ User Box Reg.] - [Create One-Touch Destination] - [Address Book
(Public)] - [PC (SMB)].
Chapter 3
2 Tap [New].
3 For [Name], specify the name to be displayed on the assigned key.

For [Sort Character], enter the same name as [Name].
% This sets the appropriate index for the name, which you entered into [Name], to [Index]. To change
the setting, tap [Index].

3
4 While checking the checklist, enter the user ID and password you wrote down.
Chapter 3
3

5 While checking the checklist, enter the host address and file path you wrote down.
% When not specifying a folder, enter a slash "/" for the file path. When specifying a folder, enter only
the folder name without slash "/".
6 Tap [Close].

3
Sending the original
1 Load the original.
Chapter 3
2 Tap [Scan/Fax].
3 Select a destination.
1
2

3
4 Check the setting if necessary.
% Tap [Check Setting] to check the setting.
Chapter 3
% You can also check the setting using the keys displayed on the Touch Panel.
% To change the setting, tap the desired key on the Touch Panel.
Settings Description
[Simplex/Duplex] Select whether to scan one or both sides of the original.
[Resolution] Specify the scanning resolution.
[Color] Select whether to scan the original in color or black and white
mode.
[File Type] Select the type of the file to save scanned data.
[Scan Size] Specify the size of the original to be scanned.
[File Name/Subject Change the file name or the subject of an E-mail to be sent.
Name/Other]

3
3.2.3 Sending data to your Mac computer (SMB Send)
Send scanned data to a computer on the network.
Once settings are configured, you can send data easily.
Chapter 3
Preparation flow


3 Checking computer information

% Check the information required for Store Address, and fill out the checklist. For details, refer to
page 3-33.
4 Configuring your computer

% Configure settings to share a computer, or create a dedicated folder to receive files. For details, refer
to page 3-34.
5 Registering destinations
% Register destinations to which files are sent while checking the checklist. For details, refer to
page 3-36.
Operation flow
2 Selecting a destination
% Select a registered destination, and check the settings such as the file type and image quality.


3
Chapter 3
Tap [Utility], and select [Device Information].
Check that the IP address is displayed.
Tips
- In Mac OS X10.6 or earlier, the default settings are available during general use, but you need to change
settings depending on your network environment.

3
Configuring this machine (Mac OS X 10.7 or later)
The following settings are only required in Mac OS X 10.7 or later.
- Select [NTLM v1/v2] in [Utility] - [Administrator Settings] - [Network Settings] - [SMB Settings] - [Client
Settings], then tap [OK].
Chapter 3
- Select [ON] in [Utility] - [Administrator Settings] - [Network Settings] - [SMB Settings] - [Direct Hosting
Setting], then tap [OK].
- Select [Utility] - [Administrator Settings] - [System Settings] - [Date/Time Settings] to specify the same
date/time and time zone between this machine and your computer, then tap [OK].

3
Checklist
While making notes in the checklist shown below, check computer information and configure settings for
preparation. The completed checklist is used for Store Address.
Name Entry column Detail

Host Address IP address to which the scanned data is sent page 3-33
Chapter 3
File Path Name of the dedicated folder to receive the scanned data page 3-34
User ID User name required to log in to the computer page 3-33

Password Password required to log in to the computer Contact your sys-
• Entering the password here is not recommended for se- tem administra-
curity reasons. tor.
Checking computer information

Check the host address and user ID.
1 Check the IP address and user name, and write it down in the Host Address and User ID columns of
the checklist.
% In the following example, the computer name is set to "User01", and the user name to "User01".

3
Configuring your computer
Create a new folder, and enable the sharing settings.
1 Create a new folder, and write down the folder name in the File path column of the checklist.
2 Enable the folder sharing settings. In the Apple menu, select [System Preferences] - [Sharing].
Chapter 3
3 Select the [File Sharing] check box, then click [Options...].

2
1
4 Select the [Share files and folders using SMB (Windows)] and user name check boxes, then click [Done].

3
5 Under [Shared Folders:], click [+].
Chapter 3
6 Select a new folder.
7 Click the new folder to check the access right.
If the access right is changed to [Read & Write], the setting is completed.

3
Registering destinations
While checking the created checklist, register the folder for receiving the scanned data as an address book
of this machine.
(Public)] - [PC (SMB)].
Chapter 3
2 Tap [New].
3 For [Name], specify the name to be displayed on the assigned key.

% For [Sort Character], enter the same name as [Name].

3
4 While checking the checklist, enter the user ID and password you wrote down.
Chapter 3
3

5 While checking the checklist, enter the host address and file path you wrote down.
% When not specifying a folder, enter a slash "/" for the file path. When specifying a folder, enter only
the folder name without slash "/".
6 Tap [Close].

3
Chapter 3
2 Tap [Scan/Fax].
3 Select a destination.
1
2

3
Chapter 3
[Color] Select whether to scan the original in color or black and white mode.
Name/Other]

3
3.2.4 Transmit the scanned data via E-mail (E-mail TX)
Send scanned data as an E-mail attachment.
This function allows you to receive data at an outside location, which is useful when a quick measure is re-
quired.
Chapter 3
Preparation flow


3 Configuring the E-mail transmission environment (Administrator)

% Configure a server for E-mail TX. For details, refer to page 3-42.
4 Configuring administrator information (Administrator)

% Register the administrator name and E-mail address used as the sender's address of an E-mail to
be sent. For details, refer to page 3-43.
Operation flow
2 Entering a destination
% Enter the destination E-mail address, and check the settings such as the file type and image quality.


3
Chapter 3
Tap [Utility], and select [Device Information].
Check that the IP address is displayed.
Tips

3
Configuring the E-mail transmission environment
1 Tap [Utility], and select [Administrator Settings] - [Network Settings] - [E-Mail Settings].
Chapter 3
2 Tap [E-Mail TX (SMTP)].
3 Select [ON] to enable E-mail TX (SMTP) settings and E-mail TX function.

3
4 Enter the SMTP server address.
Chapter 3
2
Configuring administrator information

1 Tap [Utility], and select [Administrator Settings] - [Administrator/Machine Settings] - [Administrator Reg-
istration].
2 Enter the required information, then tap [OK].

3
Chapter 3
2 Tap [Scan/Fax].
3 Enter a destination.
2
1

3
Chapter 3
4

[Color] Select whether to scan the original in color or black and white
mode.
Name/Other]

Fax Function 3.3
3
3.3 Fax Function
3.3.1 Required settings and basic operations

This section describes the settings required to send and receive a fax via a telephone line as well as the basic
operations.
Chapter 3
Preparation flow
The following describes a preparation flow to send a fax. For details, refer to the relevant page.

% Check that this machine is correctly connected to the telephone line. For details, refer to page 3-47.
2 Registering transmission information (Administrator)

% Specify the name and fax number to be displayed as a sender when sending a fax from this ma-
chine. For details, refer to page 3-48.
3 Selecting the dialing method (Administrator)

% Select the dialing method to suit your environment. For details, refer to page 3-49.
Operation flow
The following describes a flow to send a fax. For details, refer to page 3-50.
2 Entering a destination
% Enter the destination fax number, and check the settings such as the image quality.

% Press the Start key to send the original.

3.3 Fax Function
3
Check that a modular cable is connected to the LINE port of this ma-
chine.
Chapter 3

Fax Function 3.3
3
Registering transmission information
1 Tap [Utility], and select [Administrator Settings] - [Fax Settings] - [Header Information].
Chapter 3
2 Enter the sender information, then tap [OK].
• Sender settings • Sender Fax No. Settings

Enter the name to be displayed as a sender. Enter the fax number to be displayed as a sender.

3.3 Fax Function
3
Selecting the dialing method
1 Tap [Utility], and select [Administrator Settings] - [Fax Settings] - [Line Parameter Setting].
Chapter 3
2 Tap [Dialing Method].
3 For the push-button type, select [PB], and for the dial-pulse type, select [10pps].
If you do not know the type of the dialing method:

- If you do not know the type of the dialing method, operate push buttons of your phone. When you hear
"beep boop beep", set [Dialing Method] to [PB].
- If you do not hear "beep boop beep" after operating push buttons, select [10pps].

Fax Function 3.3
3
Chapter 3
2 Tap [Scan/Fax].
3 Enter a destination.
2
1

3.3 Fax Function
3
Chapter 3
4

[Color], [File Type], and [File Name/Subject Name/Other] are not available when sending to a fax
number.

Fax Function 3.3
3
3.3.2 Sending a fax directly from a PC (PC-FAX TX)
You can send a fax to the destination fax machine in the same manner as you print out data created on your
computer.
Advantages to send a fax directly from a computer
- Realizing paper saving
- Completing fax operations without leaving your desk
- Offering clear images by sending data directly from a computer
Chapter 3
Tips
- This function is not supported in the Mac operating system.
Preparation flow
The following describes a preparation flow to send a fax from a computer. For details, refer to the relevant
page.

% Check that this machine is correctly connected to the telephone line and network cable. For details,
refer to page 3-53.

3 Installing the fax driver on your computer

% Install the printer driver on your computer. For details, refer to page 3-55.
Operation flow
The following describes a flow to send a fax. For details, refer to page 3-57.
1 Creating data
% Create data to be sent using application software.
2 Configuring the fax driver

% Select a fax driver, and change the setting if necessary.
3 Entering a destination to send data

% Enter a destination to send data.

3.3 Fax Function
3
1 Check that a modular cable is connected to the LINE port of
this machine.
Chapter 3
2 Check that a LAN cable is connected to the LAN port of this
machine and the green LED is on.

Fax Function 3.3
3
Tap [Utility], and select [Device Information]. Check that the IP address is displayed.

Chapter 3
Tips

3.3 Fax Function
3
Installing the fax driver
Use the installer to install the fax driver.
This section describes how to configure the standard print settings.
computer.
Chapter 3
2 Click [Printer Install].
3 Proceed with the procedure according to the on-screen instructions.
Printers and MFPs connected to the network are automatically searched for.

Fax Function 3.3
3
4 Select this machine from the list.
1
Chapter 3
5 Select a fax driver.
6 Click [Install].

3.3 Fax Function
3
7 Click [Finish].
Chapter 3
Sending data
1 Create data to be sent using application software.
2 From the [File] menu, select [Print].
3 Select the fax driver of this machine, and click [Print].
% Clicking [Preferences] can change the setting of the printer driver as required.

Fax Function 3.3
3
% If user authentication is enabled in this machine, specify the required data such as the user name
and password.
2
Chapter 3
4 Enter the destination [Name] and [FAX Number].

% To send data to more than one destination, repeat this step.
% Clicking [Add from Address Book] can retrieve the registered destinations of this machine.
5 Click [OK].

3.4 Copy Function
3
3.4 Copy Function
Basic operations
The following describes the basic operations to make a copy.
1 If user authentication is enabled, the login screen appears. Tap the entry field or keyboard icon to enter
the required item, then tap [Login] or [Access].
Chapter 3
% If IC card or biometric authentication is enabled, refer to page 3-61.

1
3 Tap [Copy].

Copy Function 3.4
3
4 Check the basic settings.
% Check the output image configured as specified while viewing the output illustrations displayed on
the Touch Panel.
% Tapping [Check Setting] can check detailed settings.
Chapter 3
[Original Type] Specify the original type of the original.
[Color] Specify the color to output an image.
[Density] Adjust the copy density.
[Paper] Specify the output paper.
[Zoom] Specify the zoom ratio.
[Duplex/Combine] Specify double-sided copying or combine copying.
[Finishing] Configure the offset, punch, or staple setting for output paper.
5 Tap the input area for entering the number of copies.

3.4 Copy Function
3
6 Enter the number of copies using the keypad, and press the
Start key.
Chapter 3
User authentication
You can perform authentication by user or group in this machine.
Installing optional units enables IC card or biometric authentication.
If IC card authentication is enabled, pass or place the IC
card over or on the card reader of the authentication unit.
If biometric authentication is enabled, put your finger on

the finger vein reader of the authentication unit.

Registering a destination 3.5
3
3.5 Registering a destination
3.5.1 Registering an address book

The fax and scan-to-send functions can register the frequently used destinations as address books. This sec-
tion explains an example to register an address book to which a fax is sent.
Chapter 3
Using the Control Panel to register an address book - Registration from Util-
ity
Select a destination type, and register destination information.
(Public)].
2 Select the type of the destination you want to register.
3 Tap [New].

3
4 Enter the destination name you want to register.
% Tap [Name], and enter the destination name using the displayed keyboard.
Chapter 3
1

3
% Entry items and the number of setting screens vary depending on the destination type. Use [ ] or
[ ] to switch setting screens while entering the required items. For information on entry items, refer
to page 3-68.
5 Enter the fax number.

% Tap [Display Keypad] to display the keypad, and enter the fax number.
6 Tap [Close].

3
Using the Control Panel to register an address book - Registration in
scan/fax mode
Select a destination type, and register destination information.
1 Display the scan/fax screen.
2 Tap [Address Reg.].

Chapter 3
3 Tap [Input New Address].
4 Select a destination type.

3
5 Enter the fax number.
% For [Index], set searching words corresponding to [Name].
% For [Name], enter the destination name to be registered by using the displayed keyboard.
1
2
Chapter 3
3
4

5
% Entry items and the number of setting screens vary depending on the destination type. For informa-
tion on entry items, refer to page 3-68.
Registration by Direct Input
- The destination entered by using the [Direct Input] button can be registered before sending data as well.
What is an index?
- This is used as an index of a registered destination. Tap the Index key to narrow down a target desti-
nation.
- If [Favorite] is selected as an index, the destination appears in the basic screen of the transmission
screen after it has been registered in the address book; enabling the user to easily select a destination.

3
Using a computer to register a one-touch destination
In addition to using the Control Panel, address books can be registered from a computer using the utility
software, Web Connection.
0 When using Internet Explorer 6 in the IPv6 environment, you need to correct the hosts file in advance.
1 Check the IP address of this machine

Chapter 3
% Tap [Utility], and select [Device Information]. Check that the IP address is displayed.

% If no IP address is displayed, you need to configure the network. For details, refer to the User's
Guide CD.
2 Start a Web browser, enter the IP address of this machine into the URL field, then press the [Enter] key.
% For "http://192.168.1.20/", "192.168.1.20" is an IP address.
% If you use a Web browser other than Internet Explorer 6 in the IPv6 environment, enclose the IPv6
address in [ ]. For example, if the IPv6 address of this machine is "fe80::220:6bff:fe10:2f16", type in
"http://[fe80::220:6bff:fe10:2f16]/".
% If the login screen appears, enter the required items, then click [Login].
3 Select [Store Address] and click [New Registration].

3
4 Select the type of the destination you want to register.
Chapter 3
1
2

5 Enter the required information such as the name, fax number, and index.

3
3.5.2 Information required to register a destination
The items to be entered or the number of screens required to register a destination vary depending on the
transmission type. This section describes specific information required to register a destination.
Tips
- Setting items that can generally be used with defaults are omitted in this table.
Item Description
Chapter 3
[E-Mail] [Name] Enter the name of the destination to be registered

as an address book.
[E-Mail Address] Enter the E-mail address used as the destination.
[User Box] [Name] Enter the name of the destination to be registered
as an address book.
[User Box] Select a User Box to be used as a destination.

[Fax] [Name] Enter the name of the destination to be registered
as an address book.
[Fax Number] Enter the fax number of the destination.
[PC (SMB)] [Name] Enter the name of the destination to be registered
as an address book.
[User ID] Enter the login name of the destination computer.
[Password] Enter the password required to log in to the com-
puter.
[Host Address] Enter the computer name or IP address.
• Only uppercase letters are available for the
computer name.
[File Path] Enter the folder name to be used as the destina-
tion.
[FTP] [Name] Enter the name of the destination to be registered
as an address book.
[Host Address] Enter the address of the FTP server.
[File Path] Enter the directory to be used as the destination.
[User ID] Enter the user ID required to log in with FTP.
[Password] Enter the password required to log in with FTP.
[WebDAV] [Name] Enter the name of the destination to be registered
as an address book.
[User ID] Enter the user ID required to log in with WebDAV.
[Password] Enter the password required to log in with Web-
DAV.
[Host Address] Enter the address of the WebDAV server.
[File Path] Enter the directory to be used as the destination.

3
3.5.3 Registering a group
Several address books can be registered as a group.
This function is useful when you have jobs involving sending data to specified members at periodic intervals.
Registering a new group

1 Tap [Utility], and select [One-Touch/ User Box Reg.] - [Create One-Touch Destination] - [Group].
Chapter 3
2 Tap [New].

3 Enter the destination name you want to register.
% Tap [Name], and enter the destination name using the displayed keyboard.

3
4 Select destinations to be grouped.
Display and select the target address book on the destination selection screen. The following two meth-
ods can be used to search for a destination.
Chapter 3
% Search by index: Searches for the target destination name using an index.
% Search by registration number: Searches for the target destination using a registration number.
5 Repeat Step 4 until you select all address books to be grouped.

3
3.5.4 Retrieving a registered destination
Retrieve an address book or group to specify it as a destination to which data is sent.
Retrieving a destination
1 Tap [Scan/Fax].
Chapter 3
The destinations, which are categorized into [Favorite] when registering indexes, are displayed on the
basic screen.

3
2 Narrow down destinations using index and address type.
1
Chapter 3
2

3
Specifying a destination
In addition to retrieving a registered destination, a destination can be specified in various methods.
Direct Input Directly enter a destination using the keyboard screen or keypad.
Job History Specify a target destination in the job history (latest five destinations)
on the scan/fax screen.
Search Retrieves destination candidates by the prefix search function using
Chapter 3
the name (registered destination name) or address (fax number, E-
mail address, or computer name). This function is convenient when
there are too many registered destinations.
d Reference

Using a USB memory device 3.6
3
3.6 Using a USB memory device
3.6.1 Printing data in a USB memory device

Data saved in the USB memory device can be printed. This function is useful when printing data created on
a computer that is not connected to the network.
Available USB memory device
Chapter 3
- Compatible with USB version 2.0/1.1 interface

- Formatted in FAT32
- Without security function added, or with security function that can be turned off as required
– The recommended memory size is 2GB.
Available printing file types
- PDF, Compact PDF, JPEG, TIFF, XPS, Compact XPS, OpenXML (.docx/.xlsx/.pptx), and PPML
(.ppml/.vdx/.zip)
– Other file types are not supported on this machine.
Printing data
1 Connect a USB memory device to this machine.
NOTICE
Do not insert the USB memory device into the USB port close to the rear panel of this machine.
Do not use a USB device other than a flash-memory device.
2 Tap [Print a document from External Memory.].

3
3 Select data to be printed, and tap [Print].
Chapter 3
1

2
4
3
4 Check print settings.

3
NOTICE
Do not disconnect the USB memory device during data
printing.
Chapter 3

3
3.6.2 Saving the scanned data in the USB memory device (External memory)
The data scanned on this machine can be saved to the USB memory device, so it is convenient when printing
data created on a computer that is not connected to the network.
Available USB memory device
- Compatible with USB version 2.0/1.1 interface
- Formatted in FAT32
- Without security function added, or with security function that can be turned off as required
Chapter 3
– The recommended memory size is 2GB.
Specifying functions to be permitted for external memory

Change the settings to save documents in the USB memory device.

1 Tap [Utility], and select [Administrator Settings] - [System Settings] - [User Box Settings].
2 Tap [External Memory Functional Settings].

3
3 Select [Save Document] and [ON]. Tap [OK].
1
2
Chapter 3
3

3
Saving data in the USB memory device
Chapter 3
2 Connect a USB memory device to this machine.
NOTICE
Do not insert the USB memory device into the USB port close to the rear panel of this machine.
Do not use a USB device other than a flash-memory device.
3 Tap [Save a document to External Memory.].

3
4 Check the file name.
Chapter 3
5 If necessary, check the setting to save data.

% To change a file name, tap the file name or keyboard icon.
[Color] Select whether to scan the original in color or black and white mode.

NOTICE
Do not disconnect the USB memory device during data sav-
ing.

3.7 Using the guidance function
3
3.7.1 Guidance screen

This machine provides the guidance function to display the description of a function on the screen and view
an operation procedure with moving images.
If you have any questions during operation, try to use this guidance function.
Chapter 3
Getting help on the currently displayed screen:
Select [Function] on the Help Menu to display the guidance screen.
1 Press the Guidance key.
2 Select a menu.

Using the guidance function 3.7
3
3 Narrow down the information you want to know.
Chapter 3

3
Chapter 3
Name Description
[Exit] Returns to the main menu.
[To Menu] Returns to the Help Menu.
[Close] Returns to the preceding screen.

3
Getting help on the desired function or procedure:
Open the Help Menu, and select a menu depending on an objective to display the guidance screen.
1 Press the Guidance key.

Chapter 3
2 Select a menu.

3
3 Narrow down the information you want to know.
Chapter 3

3
4 Tapping [Go to function] opens the setting screen of a target function, enabling you to configure the
settings immediately.
Chapter 3
Help Menu list

The Help Menu provides the following information:
Name Description
[Function] Tap this button to display the guidance menu that has been sorted
according to the function names to be displayed on the screen.
[Search by Operation] Tap this button to display operation examples and explanations of
this machine sorted by function.
[Other Functions] Tap this button to display the guidance menu of the functions and
settings that make it easier to use this machine.
[Name and Function of Tap this button to check the name or function of each part of this
Parts] machine.
[Service/Admin. Informa- Tap this button to display the service or administrator information,
tion] administrator name, extension number, and E-mail address.
[Consumables Replace/ Tap this button to check the consumables replacement or punch
Processing Procedure] scrapping procedure with moving images.

Advanced Functions Chapter 4

Using advanced functions 4.1
4
4.1 Using advanced functions
4.1.1 What are advanced functions?

Various functions for further enhancement of the MFP operability are expressed as advanced functions in this
manual.
This machine provides the following advanced functions.
Chapter 4
Tips
- To use an advanced function, you need to register i-Option or associate with the My Panel Manager
application.
Advanced Functions
Name Description
PDF processing You can configure the required settings when converting scanned data to
a PDF file.
• This requires the registration of i-Option LK-102 v3.
Voice Guidance You can use the voice guidance in order to assist operations or prevent the
machine from operating incorrectly.
Searchable PDF You can convert the scanned data to a searchable PDF file.
Web Browser You can use the Web browser on the Touch Panel of this machine. You
can access contents on the Internet or intranet.
File Type Extension Supports functions such as a function that converts a file into a DOCX or
XLSX type, a function that generates highly-functional and high quality da-
ta, and the E-mail RX Print function.
• This requires the registration of i-Option LK-110.
ThinPrint Allows you to use this machine as ThinPrint Client (.print Client) when Thin-
Print is enabled.
• This requires the registration of i-Option LK-111.
My Panel You can customize the control panel display of this machine for each user.
• This requires the association with My Panel Manager.
My Address You can use the address book for personal use (My Address Book).
• This requires the association with My Panel Manager.
In addition, this machine supports advanced functions such as the barcode font, unicode font, and OCR font.
d Reference

4
4.1.2 Association with application
To use the My Panel or My Address function, you need to purchase My Panel Manager and enable the target
function in the application side.
For details on how to enable such a function, refer to the My Panel Manager User's Guide.
Tips
- The Upgrade Kit UK-204 is required to use the My Address function.
4.1.3 Registering the i-Option license

To add an optional function to this machine, you need to purchase i-Option and register its license.
Tips
Chapter 4
- The Upgrade Kit UK-204 is required to use i-Option LK-101 v3/LK-102 v3/LK-104 v3/LK-105 v3/LK-
106/LK-107/LK-108/LK-110.
For details on how to purchase or install an optional unit, contact your service representative.
Preparation flow
Advanced Functions
The following describes a preparation flow to use advanced functions. For details, refer to the relevant page.
1 Registering the i-Option license (Administrator)

% Register the option license on a dedicated Web site. For details, refer to page 4-4.
2 Enabling the i-Option function (Administrator)

% Enter the license code to enable the function. For details, refer to page 4-6.
3 Configuring each function (Administrator)

% Configure the required settings for each advanced function. For details, refer to page 4-8.
d Reference
For details on the procedure, refer to the User's Guide CD.

4
Registering the i-Option license
Register the request code and the contents of the token certificate on the Web site of the License Manage-
ment Server (LMS).
1 Tap [Utility], and select [Administrator Settings] - [Forward] - [License Settings] - [Get Request Code].
Chapter 4
Advanced Functions
2 Tap [Yes] and [OK].
3 Tapping [Print] prints the serial number and request code.

% Prepare at hand the printed serial number, request code, and token certificate supplied with i-Op-
tion.

4
4 Access the Web site of the License Management Server (LMS). Enter the [MFP Serial Number] and [Re-
quest Code], then click [Next].
% The URL is described in the token certificate.
Chapter 4
Advanced Functions
5 Enter the [Token Number], select the option you want to register from the [Product Description] list, then
click [Next].
6 Confirm the registration contents, then click [Generate License Code].

4
7 The license code and function code are issued.
Chapter 4
Tips
Advanced Functions
- The issued license code and function code are required to enable i-Option. You should write them
down on a memo pad or print them out on paper by clicking [Print].
- You could also store them in your USB memory device. The license code input could be omitted by
using a USB memory device to achieve a convenient operation.
- When using a USB memory device, insert the USB memory device and click [Download] to store the
license code.
Enabling the i-Option function

Register the license and function codes in this machine.
By inputting the codes
1 Tap [Utility], and select [Administrator Settings] - [Forward] - [License Settings] - [Install License] -
[Function/Licence Code].

4
2 Enter the license and function codes you wrote down.
Chapter 4
3
3 Select [Yes], then tap [OK].
Advanced Functions
1
This machine restarts automatically.

4
By using a USB memory device
1 Connect the USB memory device stored with the license

code.
Chapter 4
2 Tap [Utility], and select [Administrator Settings] - [Forward] - [License Settings] - [Install License from
Ext. Memory].
Advanced Functions
Configuring each function

Configure the required settings for each advanced function.
d Reference
For details on the required setting items for each advanced function, refer to the User's Guide CD.

4.2 Using the Voice Guidance
4
4.2.1 Required Settings and Procedures

Using the voice guidance, you can confirm explanations of screens, keys, and key-related operations by
voice.
The voice guidance is available on the Enlarge Display screen, Guidance screen, and Accessibility Settings
screen, and useful to assist operations or prevent this machine from operating incorrectly.
Chapter 4
Advanced Functions
Tips
- The Upgrade Kit UK-204 is required to use the voice guidance.
- You need to purchase i-Option LK-104 v3 and register its license.
- You need to install the Local Interface Kit on this machine.
- To use the voice guidance, administrator settings are required in advance.
- The voice guidance function for operating the Register key is not required for this machine equipped
with the Keypad KP-101. Also, the voice guidance can be operated by using the Keypad.
Preparation flow
The following describes a preparation flow to use the voice guidance. For details, refer to the relevant page.
1 Enabling the voice guidance function (Administrator)

% Enter the voice guidance of the machine side to enable its function. For details, refer to page 4-10.
2 Assigning the voice guidance function to the Register key (Administrator)

% For details, refer to page 4-11
% This setting is not required when the Keypad KP-101 is equipped on this machine.
3 Specifying the volume and speed

% Specify the volume or speed to read out. For details, refer to page 4-12.
Operation flow
The following describes an operation flow. For details, refer to page 4-13.
1 Starting the voice guidance
2 Playing the voice guidance

% Move the voice cursor to operate the voice guidance.
3 Ending the voice guidance

Using the Voice Guidance 4.2
4
Enabling the voice guidance function
Register the function and license codes in this machine.
Then, configure settings to start the voice guidance.
1 Enable the i-Option function. Tap [Utility], and select [Administrator Settings] - [Forward] - [License Set-
tings] - [Install License] - [Function/License Code].
Chapter 4
Advanced Functions
2 Enter the license and function codes you wrote down.

4
4 Enable the voice guidance. Tap [Utility], and select [Administrator Settings] - [Forward] - [Voice Guid-
ance Settings].
Chapter 4
3
Advanced Functions
Assigning the voice guidance function to the Register key
Assign the voice guidance function to any of the Register keys.
1 Tap [Utility], and select [Administrator Settings] - [System Settings] - [Forward] - [Registered Key Set-
tings].
2 Select the [Register key] to be assigned with the voice guidance function.

4
3 Select [Voice Guide], then tap [OK].
1
Chapter 4
Specifying the volume and speed

Advanced Functions
Specify the volume or speed to read out.
1 Tap [Accessibility], and select [ ] - [Voice Guidance Settings].
2 Specify the volume or speed.

% [Volume]: Use [Higher] or [Lower] to adjust the volume.

4
% [Voice Speed]: Select the speed to read out.
Chapter 4
Operating the voice guidance
Advanced Functions
1 Press the Register key assigned with the voice guidance on
the screen that supports the voice guidance.
% For information on the operations when the Keypad KP-101 is equipped, refer to page 4-14.
% The following screens support the voice guidance.
• Enlarge Display screen

• Guidance screen
• Accessibility Settings screen
You will hear a voice to announce the start of the voice guidance, and the blue-frame voice cursor will
be displayed.

4
2 Tap the key for which a voice guidance is required.
3 Press the Register key assigned with the voice guidance to

exit the voice guidance function.
Chapter 4
Keypad operations for voice guidance

1
Advanced Functions
Press Voice Guide on the screen that supports the voice guid-
ance.
2 Use the keypad to operate the voice guidance.

% Position the voice cursor at the key you want to hear the
guidance for.
% Determine the position of the voice cursor.

4
% Reading out starts.
Chapter 4
3 Press Voice Guide to end the voice guidance.
Advanced Functions
For the voice guidance, use the keypad to perform various operations.
Key Description
0 Reads out the explanation of a function assigned to each key.
1 Reads out the explanation of the currently displayed screen.
2 Reads out the setting items configured by the currently displayed function.
(Available only in copy or scan/fax mode on the Enlarge Display screen)
3 Stops the currently replayed voice guidance.
4 Moves the voice cursor to the previous.
5 Determines the position of the voice cursor.
6 Moves the voice cursor to the next.
7 Reads out the setting items configured by the currently displayed function.
(Available only in copy or scan/fax mode on the Enlarge Display screen)
8 Reads out the previously read-out information again.
9 Reads out the currently selected key.
# Turns up the volume by one level.
• The volume can be adjusted at any time while using the voice guidance.
* Turns down the volume by one level.
• The volume can be adjusted at any time while using the voice guidance.

4
Chapter 4
Advanced Functions

Frequently Asked Questions Chapter 5

Print 5.1
5
5.1 Print
5.1.1 Q1. Can I print data on an envelope or postcard?

A1. Yes, you can also print on envelopes and postcards.
Execute a print job on your computer then load envelopes or postcards into this machine to execute a print
job on it.
Operation procedure
1 Open the file in the application, and click [File]. Then click [Print] from the menu.
Chapter 5
2 Select this product from [Select Printer] (or [Printer Name]) then click [Preferences] (or [Properties]).
3 In [Original Size] on the [Basic] tab, select [Envelope] or [Postcard].

% Various sizes of envelopes are available. Select the correct paper size for the envelopes you have
Frequently Asked Questions
loaded.
4 Check that [Paper Size] is set to [Same as Original Size].

5.1 Print
5
5 Select [Bypass Tray] from [Paper Tray].
Chapter 5
Click [Paper Settings for Each Tray].

7 Select the relevant paper type from [Paper Type] then click [OK].
% To print on postcards, select [Thick 3] or [Thick 3 (Side2)]. To print on envelopes, select [Envelope].
8 Click [OK].
9 Execute printing.

Print 5.1
5
10 Load envelopes or postcards into the Bypass Tray with the
print side facing down.
11 If the paper setting of [Bypass Tray] in this machine is the same as that of [Original Size] in step 3 or
[Paper Type] in step 7, printing starts without further setting.
If the paper setting is different, the following screen appears. Tapping [Complete] starts printing.
% If you cannot tap [Complete], remove the envelopes or postcards loaded in the Bypass Tray and
Chapter 5
reload them, then tap [Complete].


5.1 Print
5
5.1.2 Q2. Can I print on custom size paper?
A2. Yes, you can. Specify [Bypass Tray] on the print screen and load custom size paper into the Bypass Tray.
Operation procedure
3 In [Original Size] on the [Basic] tab, select [Custom Size].
Chapter 5
4 Enter the size of the paper you have loaded, then click [OK].

Print 5.1
5
5 Check that [Paper Size] is set to [Same as Original Size].
6 Select [Bypass Tray] from [Paper Tray].

Chapter 5
7 Click [Paper Settings for Each Tray].

5.1 Print
5
8 Select the relevant paper type from [Paper Type], then click [OK].
Chapter 5
9 Click [OK].
10 Execute printing.

11 Load custom size paper into the Bypass Tray with the print side facing down.
12 Tap [Complete] on the Control Panel of the machine.
5.1.3 Q3. Can I directly print a file in a USB memory device?

A3. Yes. You can print a file simply by inserting the USB memory into the USB Port of the machine.
See the table below for the types of files that can be printed and the operating conditions of the USB memory.
Item Specifications
Supported standards USB 2.0
File system FAT32
Types of printable files PDF, Compact PDF, JPEG, TIFF, XPS, Compact XPS, OpenXML
(.docx/.xlsx/.pptx), and PPML (.ppml/.vdx/.zip)
Operation procedure
1 Insert a USB memory into the USB Port of the machine.

Print 5.1
5
2 Tap [Print a document from External Memory.].
Chapter 5
3 Select a file to print, then tap [Print].

% Select a folder, then tap [Open] to list documents and folders in the folder. Tap [Top] to return to the
location one layer above.
4 Change the print settings as necessary, and press Start on the Control Panel.

5.1 Print
5
5.1.4 Q4. Can printing be restricted by user?
A4. Yes. You can set user authentication to restrict printing by user. That enables output control by user, lead-
ing to cost reductions.
How to set
1 Tap [Utility], then select [Administrator Settings].
2 Enter the password, then tap [OK].
3 Select [User Authentication/Account Track] - [General Settings] - [User Authentication].
4 Select [Authenticate], select an authentication method, then tap [OK].

% The authentication status may be [ON (MFP)], [External Server Authentication], [Main + External
Server], [Enhanced Server Authentication], or [Main + Enhanced Server] authentication. For informa-
tion on server-based user authentication, contact the server administrator.
Chapter 5
5 Tap [OK].
7 Select [User Authentication Settings] - [User Registration].
8 Select the registration number of a target user, then tap [Edit].

Print 5.1
5
9 Enter the user name and password in [User Name] and [Password].
% If you have selected a registered user in Step 8, no information has to be entered.
Chapter 5
10 Tap [Max. Allowance Set] and [Color] or [Black], then enter the maximum allowance for the number of
color/black originals that the user can print, using the Keypad.
% To manage the upper limit without distinguishing between the color and black originals, tap [Total
Allowance]. Then, tap [Total], enter the upper limit using the Keypad, and tap [OK].
11 Tap [OK].
12 Tap [Function Permission] to set the limit for the respective functions.

5.1 Print
5
[Copy] Specify whether to allow a copy job.
[Scan] Specify whether to allow a scan job.
[Fax] Specify whether to allow a fax job.
[Print] Specify whether to allow a print job for a file.
[User Box] Specify whether to allow any operation of a file saved in the User Box.
[Print Scan/Fax TX] Specify whether to allow a print job for a file to send.
[Save to External Memory] Specify whether to permit saving of files to an external memory.
[External Memory Docu- Specify whether to allow scanning of files saved in the User Box.
ment Scan]
[Manual Destination Input] Specify whether to allow manual input of a destination.
[Cellular Phone/PDA] Specify whether to allow transferring of files from Bluetooth devices to this
machine.
[Web Browser] Specify whether to allow use of the Web browser.
Chapter 5
13 Tap [OK].
14 Tap [OK].

5.1.5 Q5. What types are available for printing finish?
A5. Various finish modes are available according to the options installed on this machine, such as stapling,
punching and binding.
Staple
Stapling is enabled to bind at a corner or at two positions. This method is useful for printing handout material
among other things.
Tips
- The Finisher is required to use the Staple function.

Print 5.1
5
Punch
Punching is enabled for filing holes.
Tips
- To use the Punch function:
– The Finisher FS-534 and Punch Kit PK-520 or the Finisher FS-533 and Punch Kit PK-519 are re-
quired.
– The Finisher FS-535 and Punch Kit PK-521 or the Z Folding Unit ZU-606 are required (only for bizhub
C554e).
Chapter 5
Center Staple & Fold

Center stapling is enabled for booklet-like finish.
Tips
- To use the Center Staple & Fold function:
– The Finisher FS-534 and Saddle Stitcher SD-511 are required.
– The Finisher FS-535 and Saddle Stitcher SD-512 are required (only for bizhub C554e).
Fold
Half-folding, tri-folding, or Z-folding is enabled. This function is useful for direct mail and information notes.
Tips
- To use the Half-Fold or Tri-Fold function:
– The Finisher FS-534 and Saddle Stitcher SD-511 are required.
– The Finisher FS-535 and Saddle Stitcher SD-512 are required (only for bizhub C554e).
- To use the Z-Fold function:
– The Finisher FS-535 and Z Folding Unit ZU-606 are required (only for bizhub C554e).
Operation procedure

5.1 Print
5
3 Select the check box for the desired finish on the [Finish] tab. If you have selected the [Staple], [Punch]
or [Fold] check box, specify the quantity, positions and other necessary settings.
% The number of punched holes varies depending on the country you are in.
Chapter 5
4 Click [OK].

Click [Print].
5.1.6 Q6. Can I print on very long sheets of paper such as a banner?
A6. Yes, you can print on a banner or other long sheet of paper by using the Banner Printing function.
The paper types below can be used for banner printing.
Paper width Paper length Paper weight

8-1/4 to 11-11/16 inches (210 to 18 to 47-1/4 inches (457.3 to 33-13/16 to 55-7/8 lb
297 mm) 1200 mm) (127 g/m2 to 210 g/m2)
Tips
- When loading long sheets of paper, mount the Mount Kit MK-730 for long paper.
How to set
1 Tap [Utility] and select [Banner Printing].
2 Select [Allow], then tap [OK].

Print 5.1
5
3 Check that the screen waiting for banner printing job has appeared.
% If a print job is received with a paper setting of a non-banner size while the machine is waiting to
print on a banner, that job is queued.
Chapter 5
5
Select this product from [Select Printer] (or [Printer Name]) then click [Preferences] (or [Properties]).
6 In [Original Size] or [Paper Size] on the [Basic] tab, select [Custom Size].
7 Enter values for [Width] and [Length] of the paper for printing, then click [OK].

5.1 Print
5
8 Check the paper tray and paper type settings automatically changed, then click [Yes].
9 Click [OK].
10 Click [Print].
11 Load paper for banner printing with the print side face down then tap [Complete].
Printing on the banner paper starts. Support the ejected banner paper by hand.
Chapter 5
% To continue banner printing, execute printing from the computer.

12 Tap [Exit].

Print 5.1
5
13 Tap [Yes].
Chapter 5

5.2 Scan
5
5.2 Scan
5.2.1 Q1. Can frequently used destinations be registered?

A1. Yes. You can register frequently used destinations in the address book. For details, refer to page 3-62.
You can also put a number of one-touch destinations in one group and register them as a group. For details,
refer to page 3-69.
Once you have registered a one-touch or group destination, you can recall it by simply tapping the assigned
key. For details, refer to page 3-71.
Tips
- You can register up to 2,000 one-touch destinations in the address book.
- Up to 100 group destinations can be registered.
- To register a group destination, members must have been registered as one-touch destinations.
Chapter 5

Fax 5.3
5
5.3 Fax
5.3.1 Q1. Can I check fax transmission and reception logs?

A1. Yes. You can print out transmission and reception logs as a report.
Reports can be prepared for scan and send logs, fax communications (transmission and reception logs), fax
transmission logs and fax reception logs.
Operation procedure
1 Tap [Job List].
2 Specify a report type in [Report Type] on the [Comm. List] tab, and tap [Proof Print], then press Start.
% Set [Output Limit] to specify the number of transmission and reception records to print.
Chapter 5
5.3.2 Q2. Can I send a fax to a number of destinations at one time?

A2. Yes, you can.
It eases the operation to register a group that contains a number of destinations beforehand.
The maximum number of destinations that you can specify for a single transmission depends on how the des-
tinations are set.
Item Specifications
When using the address book 500 addresses
Up to 30 User Boxes
When directly entering ad- E-mail 5 addresses
dresses
User Box 1 User Box
Fax 100 addresses
Tips
- When registering a group, even destinations of different types can be registered in one group.
Operation procedure: Selecting multiple addresses from the address book


5.3 Fax
5
2 Tap [Scan/Fax] and select a destination.
% You can select more than one one-touch destination from the address book. [No. of Address] dis-
plays the number of selected destinations.
% To cancel the destination setting, tap the Address Book key for the destination to be canceled.
% Select an index to narrow down destinations to display.
% Specify [Add. Type] to narrow down the types of destinations to display.
% Tap [Check Setting] to check detailed information on the destinations you have set or to cancel des-
tinations.
% You can also select a group.
Chapter 5
3 Press Start to start scanning of the original.
Operation procedure: Directly entering multiple destinations

2 Tap [Scan/Fax] and select an destination type from [Direct Input].

Fax 5.3
5
3 Enter a destination, then tap [OK].
% Tap [Next Dest.] on the address input screen to continue address entry (not enabled for a User Box).
Chapter 5
4 Repeat steps 2 and 3 to complete entry of all destinations.

[No. of Address] displays the number of entered destinations.
% Tap [Check Setting] to check detailed information on the destinations you have entered or to cancel
destinations.
5 Press Start to start scanning of the original.
5.3.3 Q3. Can I register more than one sender name to appear on faxes so that dif-
ferent ones can be used in different use cases?
A3. Yes, you can register multiple sender names and select one when sending a fax.
How to set: Registering sender names

3 Select [Fax Settings] - [Header Information] - [Sender].

5.3 Fax
5
4 Select a number, then select [New].
Chapter 5
5 Enter the sender name, then tap [OK].
6 Repeat Steps 4 and 5 to complete entry of all sender names.

% You can register up to 20 sender names.

% To edit a registered sender name, select a sender name and tap [Edit], change the sender name and
tap [OK].
% To delete a registered sender name, select the sender name and tap [Delete], select [Yes], then tap
[OK].
% To set the default sender name, select a sender name and tap [Set as Default].
Tips
- If [Administrator Settings] - [Fax Settings] - [TX/RX Settings] - [Individual Sender Line Setup] is set to
[ON] while multiple lines are used, the default sender name can be specified for each line.
How to set: Selecting a sender name upon fax transmission

2 Tap [Scan/Fax] and select a destination.
3 Tap [Application] and select [Fax Header Settings].
4 Select a sender name to print on the fax and tap [OK].
5 Press Start to start fax transmission.

Fax 5.3
5
5.3.4 Q4. Is it possible to cut down on the communications expenses by using a
network?
A4. Yes. Use the Internet Fax function to send an E-mail message with an attachment containing the scanned
data merely at expenses for online communications via the Internet.
Within your intranet, the IP Address Fax function can be used. For IP Address Fax, specify either the IP ad-
Chapter 5
dress, host name or E-mail address of the destination fax machine to directly send a fax to that destination.
No mail server is required.
Tips
- To use the Internet Fax and IP Address Fax functions, ask your service representative to configure set-
tings. For details, contact your service representative.
- To use the Internet Fax function, this machine must be connected to the network and you have an en-
vironment enabled for E-mail transmissions and receptions.
- The Fax Kit is required to use the IP Address Fax function.
Operation procedure: Sending an Internet fax

2 Tap [Scan/Fax] and select [Internet Fax] from [Direct Input].

% If you have registered one-touch destinations for the Internet Fax function, you can select them from
[Address Book].

5.3 Fax
5
3 Enter the E-mail address of the destination in [Address] and select a compression format, paper size
and resolution supported by the recipient machine from [Receiver RX Ability].
Chapter 5
4 Tap [OK].
5 Press Start to start Internet fax transmission.
Operation procedure: Sending an IP address fax

2 Tap [Scan/Fax] and select [IP Address Fax] from [Direct Input].
% If you have registered one-touch destinations for the IP Address Fax function, you can select them
from [Address Book].
3 Enter either the IP address, host name or E-mail address of the destination in [Address], the port
number used for fax transmission in [Port Number], then select [Color] or [Black&White] from [Machine
Type of Dest.].
4 Tap [OK].
5 Press Start to start IP address fax transmission.

Fax 5.3
5
5.3.5 Q5. How can I avoid printing out unwanted faxes?
A5. Save received faxes in a User Box without printing them out then print out only the faxes you need.
Operation procedure: Configuring to save received faxes in a User Box

Chapter 5
3 Select [Fax Settings] - [Function Settings] - [Memory RX Setting].
4
Select a line, tap [Yes], enter the password for processing faxes saved in a User Box using the Keypad,
then tap [OK].
Tips
- If [Administrator Settings] - [Fax Settings] - [TX/RX Settings] - [Individual Receiving Line Setup] is set to
[ON] while multiple lines are used, you can specify whether to use the Memory RX function for each line.
How to set: Printing faxes saved in a User Box

1 Tap [User Box].

5.3 Fax
5
2 From [System], select [Memory RX].
Chapter 5
4 Select a file then tap [Print].

% You can also long-tap the target file to display the menu icon, then drag and drop it to to get

the same result.
5 Check the message, then tap [Yes].

The fax is printed and automatically deleted from the Memory RX User Box.
5.3.6 Q6. Can I forward an incoming fax?

A6. Yes, you can forward a received fax to another fax machine, a computer or an E-mail address by regis-
tering forwarding destinations beforehand.

Fax 5.3
5
How to set
3 Select [Fax Settings] - [Function Settings] - [Forward TX Setting].
4 Select [Yes] and configure the respective items for forwarding faxes.
Chapter 5
[Output Method] To have forwarded faxes printed out on this machine, select [Forward &
Print]. To have faxes printed out on this machine only in the case forward-
ing has failed, select [Forward & Print (If TX Fails)].
[Forward Dest.] Enter the fax number of the forwarding destination. You can also specify a
computer or E-mail address for the forwarding destination by tapping [Se-
lect from Address Book] and selecting it from registered one-touch desti-
nations.
[Select Line] When multiple lines are used, select a line used to send a fax.
5 Tap [OK].
Tips
- If [Administrator Settings] - [Fax Settings] - [TX/RX Settings] - [Individual Receiving Line Setup] is set to
[ON] while multiple lines are used, you can specify whether to use the Forward TX function for each line.

5.3 Fax
5
5.3.7 Q7. Can I directly fax a file on my computer without leaving my desk?
A7. Yes. You can fax a file in the same manner as you print out a file created on your computer.
Tips
- The following preparatory steps are required:
– Installing the fax driver to the computer
Chapter 5
– Connecting this machine to the network
Operation procedure

2 Select a fax driver from [Select Printer] (or [Printer Name]) then click [Print] (or [OK]).
3 Enter the name and the fax number of the destination, then click [Add Recipients].
% You can also specify the destination by clicking [Add from Address Book] and selecting one from
registered one-touch destinations.
% To specify more than one destination, repeat step 3.
% To delete a destination you have specified, select the destination to delete from [Recipient List] and
click [Delete From List].
4 Click [OK] to start fax transmission.

Copy 5.4
5
5.4 Copy
5.4.1 Q1. Can I print on paper of a custom size?

A1. Yes, you can. Load custom size paper into the Bypass Tray and specify the bypass tray on the paper
screen of copy mode.
It is a good idea to have the frequently used custom size of paper registered in the memory.
Operation procedure: Copying on paper of a custom size

2 Load custom size paper into the Bypass Tray with the print side facing down.
3 Tap [Copy].
4 Tap [Paper] and select the bypass tray. Then, tap [Change Tray Setting].
Chapter 5
5 Select one from the paper type options, then tap [Custom Size].

5.4 Copy
5
6 In [Custom Size Settings], specify the paper size by entering values for the lengths along [X] and [Y],
then tap [Close].
Chapter 5
7 Press Start to start copying of the original.
Operation procedure: Registering a custom size of paper in memory

1 Tap [Copy].
3 Tap [Custom Size].
4 In [Custom Size Settings], specify the paper size by entering values for the lengths along the [X] and [Y]
directions.

Copy 5.4
5
5 In [Registered Paper Sizes], select a location for registration, then tap [New].
% Up to five different sizes can be registered in memory.
% Select Registration Size, then tap [Edit Name] to rename the registration size.
Chapter 5
Operation procedure: Recalling the custom size registered in memory

1
Tap [Copy].
3 Tap [Custom Size].

5.4 Copy
5
4 Select the paper size to recall from [Registered Paper Sizes], then tap [Recall].
Chapter 5
5.4.2 Q2. Can I copy on an envelope or postcard?
A2. Yes, you can also copy on an envelope and postcard.
Load envelopes or postcards into the Bypass Tray, then specify the paper type and paper size of the Bypass
Tray.

Operation procedure: Copying on envelopes
1 Load envelopes into the Bypass Tray with the print side facing down.
3 Tap [Copy].

Copy 5.4
5
5 Select [Envelope] from [Paper Type], then tap [Standard Size].
Chapter 5
6 From [Other], select the size of the envelope.

% Various sizes of envelopes are available. Specify the correct paper size for the envelopes you have
loaded.
7 Tap [Close].
8 Press Start to start copying of the original on envelopes.
Operation procedure: Copying on postcards

1 Load postcards into the Bypass Tray with the print side face down.
3 Tap [Copy].

5.4 Copy
5
Chapter 5
5 Tap [Standard Size].

6 From [Other], select [4 e 6]([A6 Card]).
% When [4 e 6]([A6 Card]) is specified for the paper size, the paper type is automatically set to [Thick3].
7 Tap [Close].
8 Press Start to start copying of the original on postcards.

Copy 5.4
5
5.4.3 Q3. Can I check the finish before starting copying?
A3. Yes, you can check the finish by outputting a proof copy.
You check either by referring to a preview image or by outputting just one copy for checking how it is actually
finished.
Using a proof copy helps preventing copy errors.
How to set: Checking the finish with a preview image

2 Tap [Copy].
3 Specify copy settings and the number of copies as necessary, then tap [Preview].
4 Tap [Preview on Screen], select the original loading direction, then tap [Start].
Chapter 5
5 Tap [View Page].

The screen used to change the preview display appears.
% To continue scanning originals, load the original, then tap [Start Scan].
% To start copying, tap [Print] or press the Start key.
% If a multi-page original has been scanned, you can flick the preview image to feed pages forward or
backward.
6 Check the preview display, and rotate the image or change settings as needed.
% To continue scanning originals, load the original, then tap [Start Scan].
% To enlarge the preview image, double-tap the image.
% To enlarge or reduce the preview image, pinch-in or pinch-out the image.

5.4 Copy
5
% If you apply the rotation function to the preview image, it can be rotated 180 degrees.
% When scanning a multi-page original, you can tap the left or right page feed key to feed pages for-
ward or backward.
Chapter 5
7 Tap [Print] to start copying the original.
How to set: Checking the finish by outputting one copy

2 Tap [Copy].
3 Specify copy settings and the number of copies as necessary, then tap [Preview].
4 Tap [Print], select the original loading direction, then tap [Start].
One copy is output.
5 Check the finishing of the copy.
6 If the finishing is acceptable, press Start.

Copy 5.4
5
5.4.4 Q4. Can I easily copy various cards such as an insurance card or driver li-
cense card?
A4. Yes, you can copy the front and back sides of a card, side by side, on the same side of one sheet of paper.
Operation procedure
1 Place a card on the Original Glass.
Chapter 5
2 Tap [Copy].
3 Tap [Paper], select a paper tray to load paper into in order to copy a card, then tap [Close].
% If you specify [Card Shot], you must specify a paper tray other than [Auto].
4 Tap [Application], then select [Card Shot].

5.4 Copy
5
5 Tap [ON], then configure each item so that it corresponds with the finishing image.
Chapter 5
[Original Size] Enter the size of a card to be copied. Alternatively, you can recall the pre-
registered size from [Registered Paper Size].
[Layout] Select how to arrange the front and back sides of a card on paper.
[Zoom] [Full Size] Copy the card by enlarging it according to the paper size.

[x1.0] Copy the card to the same size as the original (card).
6 Tap [OK].

The front side of the card is scanned.
8 Turn the card over, and place it on the Original Glass.
10 After both sides of the card have been scanned, tap [Finish].
11 Press the Start key to start to copy the scanned card.

User Box 5.5
5
5.5 User Box
5.5.1 Q1. Can I create a User Box, or print or download a file in a User Box?
A1. Yes. Use Web Connection or the Windows file sharing function to create a User Box or manage files in
a User Box without leaving your desk.
Tips
- To use the Windows file sharing function, configure the SMB server setting and create a Public User
Box to share the files in advance. For details, refer to the User's Guide CD.
- The Windows file sharing function is available only for files saved in a Public User Box using the User
Box mode or the scan/fax mode.
Operation procedure: Using Web Connection

1 Start the Web browser.
2 Enter the IP address of the machine in the URL field, and then press [Enter].
Chapter 5
% You can check the IP address from [Utility] - [Device Information].

% When user authentication or account tracking is enabled, fill in the [User Name] and [Password],
then click [Login].
3 Click the [Box] tab.

4 Complete the following steps:

% Create/edit/delete a User Box.
% Print/send a file in a User Box.
% Download a file in a User Box to your computer.
% Copy/move/delete a file in a User Box.
Tips
- Up to 400 MB of the file size can be downloaded to your computer at one time.
- If the file size exceeds 400 MB, specify the page range setting before downloading in limit the file size
to download at one time to less than 400 MB.
Operation procedure: Using the Windows file sharing function

1 Open the network on your computer.
2 Search for this machine using the host name.

% To view the host name of this machine, select [Utility] - [Administrator Settings] - [Network Settings]
- [SMB Settings] - [SMB Server Settings] - [SMB Server Common Settings] - [SMB Host Name].

5.5 User Box
5
3 Open the shared folder of this machine to search for the target file.
% The shared folder of this machine is named in the format, "(9-digit User Box number)_(User Box
name)".
% If the ID and password are required to open the shared folder, enter the following information.
ID: User Box number
Password: Password specified for the Public User Box
4 Complete the following steps:

% Download a file to your computer.
% Copy or delete a file.
Chapter 5

Other 5.6
5
5.6 Other
5.6.1 Q1. Can more than one computer use the same settings for the printer driv-
er?
A1. Yes. Use the Driver Packaging Utility located on the PAGESCOPE UTILITIES CD-ROM to set them
identically.
The Driver Packaging Utility can be used to create an install package with various settings registered for a
printer driver.
First, the administrator uses the Driver Packaging Utility to create an install package for the printer driver.
Next, simply execute that install package on a computer to apply identical settings to, and the printer driver
configured with the same settings is installed.
Operation procedure : Preparing for an install package

Chapter 5
1 Insert the PAGESCOPE UTILITIES CD-ROM in the CD drive.
2 Select [Administration Tools-2] - [Driver Packaging Utility] - [Download Page].
3 Click [Agree] to accept all terms specified in the license agreement.

4 Click [Download] under Driver Packaging Utility that is suitable for this machine to download the Driv-
er Packaging Utility file to a desired location.
5 Double-click the Driver Packaging Utility file you have downloaded and decompress it to a desired
location.
Operation procedure: Creating an install package

1 Double-click [DPU.exe] in the [DPU] folder.
2 Select a language and click [Agree].
3 Click [Edit] and click [Add Printer] on the menu.
4 Select a reference printer for the install package, then click [OK]. Select a printer that satisfies the fol-
lowing requirements:
% The printer is supported by the Driver Packaging Utility.
% The printer has already been installed on the computer you are currently using.
% The printer is to be connected to a TCP/IP or Internet port.
5 On the [Printer] tab, check that the name of the printer selected in Step 4 is displayed in [Printer Name].
6 On the [Preferences], select [Copy from this printer], then check the [Set as default printing preferences]
box.
7 On the [Driver] tab, click [Browser] for the [Path to Printer Driver] to specify the folder containing the
printer driver selected in Step 4.
8 Click [OK].
9 Click [Configuration] and click [DPU Folder] on the menu.
10 In [Common Folder Path] or [Individual Folder Path], specify the path to the location to save the install
package to, then click [OK].
% Click [Browser] to specify the location in a folder tree.
11 Click [File] - [Save As].

5.6 Other
5
12 Configure settings for respective items and click [Save].
[DPU Folder] Select a desired location for saving the install package.
[Package Name] Enter a name for the install package. A folder is created for the install pack-
age under the name entered here.
[Comment] Enter description of the install package.
[Switch to the following Check the box and fill [User Name], [Password] and [Domain Name], and
user when executing the the user is switched to the specified user when the install package is exe-
package] cuted.
[Destination for saving Specify the path to the location for saving install package creation logs.
package log] Click [Browser] to specify the location in a folder tree.
[Open the folder containing Check the box if you wish to display the folder for saving the install pack-
the package file.] age when saving it.
13 After the creation of the install package is completed, click [OK].
Chapter 5
14 Distribute the install package created to users sharing the printer driver settings.
% In Driver Packaging Utility, click [Configuration] - [Package File] to display the folder storing the
install package.

Operation procedure: Executing the install package
1 Copy the folder for the install package to a desired location.
2 Double-click the execution file of the install package you have created.
3 Click [Start].
4 Select a language and click [Agree].
5 Select a package to install and click [Start].
6 After the installation of the printer driver is completed, click [Finish].
7 Open the properties for the installed printer driver and check the settings.
% For the display of the properties, refer to the User’s Guide CD.
5.6.2 Q2. Can I restrict available functions by user?

A2. Yes. With user authentication enabled, you can restrict functions available by user.
How to set
3 Select [User Authentication/Account Track] - [User Authentication Settings] - [User Registration].
4 Select a user whose access to functions needs to be limited, then tap [Edit].

Other 5.6
5
5 Tap [Function Permission] to set the limit for the respective functions.
Chapter 5
[Copy] To allow using the full copy function, select [Full Color/Black]. To allow
copying in black and white only, select [Black Only]. To prohibit copying,
select [Restrict].
[Scan] To allow using the full scan function, select [Full Color/Black]. To allow
scanning in black and white scan, select [Black Only]. To prohibit scanning,
select [Restrict].
[Fax] To allow using the full fax function, select [Full Color/Black]. To allow only
black-and-white fax transmission, select [Black Only]. To prohibit fax
transmission, select [Restrict].
[Print] To allow using the full print function, select [Full Color/Black]. To allow
printing in black and white only, select [Black Only]. To prohibit printing, se-
lect [Restrict].
[User Box] To allow operating files in User Boxes, select [Allow]. To prohibit operating
files in User Boxes, select [Restrict].
[Print Scan/Fax TX] To allow printing of outgoing files, select [Full Color/Black]. To allow print-
ing of outgoing files in black and white only, select [Black Only]. To prohibit
printing of outgoing files, select [Restrict].
[Save to External Memory] To allow saving of data to an external memory device, select [Allow]. To
prohibit saving of data to an external memory device, select [Restrict].
[External Memory Docu- To allow loading data from an external memory device, select [Allow]. To
ment Scan] prohibit loading data from an external memory device, select [Restrict].
[Manual Destination Input] To allow manual entry of destinations, select [Allow]. To prohibit manual
entry of destinations, select [Restrict].
[Cellular Phone/PDA] To allow transferring of files from Bluetooth devices to this machine, select
[Allow]. To prohibit transferring of files from Bluetooth devices to this ma-
chine, select [Restrict].
[Web Browser] To give permission to use Web browser, select [Allow]. To give no permis-
sion to use Web browser, select [Restrict].
6 Tap [OK].
7 Tap [OK].
8 Repeat steps 4 to 7 to restrict available functions by user.
Tips
- If an attempt is made to execute a restricted function, a message appears notifying the user that it is
prohibited.

5.6 Other
5
5.6.3 Q3. Can I change the keying and operation sounds of this machine?
A3. Can delete the operation sound of the Touch Panel, and adjust the sound type and volume.
How to set
1 Tap [Accessibility] and select [Sound Setting].
2 To set whether to output keying and other sounds, select [Sound Setting] and set whether to output
respective sounds.
Chapter 5
[All Sounds] Specify whether to output all sounds.
[Confirmation Sound] Set whether or not to output a sound notifying that an operation takes
place on the Control Panel or Touch Panel.
[Successful Completion Set whether or not to output a sound notifying successful completion of an
Sound] operation.
[Completed Preparation Set whether or not to output a sound notifying that this machine is ready
Sound] for operation.
[Caution Sound] Set whether or not to output a sound notifying the need for part replace-
ment or occurrence of an error.
[Deletion Sound] Set whether or not to output a sound when Document or Job is deleted.
[Authentication Sound] Set whether or not to output a sound in association with the authentication
result when logging in.
3 Tap [OK].

Other 5.6
5
4 Tap [Sound Type/Volume Setting], and set the sound type and volume.
% The sound type and volume can not be set for the item where the [Sound Setting] is set to [No].
Chapter 5
[Batch Setting] All the sound type and volume will be set at once. Select the sound type
from six types and select the sound volume from [High], [Medium], or [Low]
for adjustment.
[Individual Setting] All the sound type and volume will be set separately.
5 To set the sound type and volume separately, tap [Individual Setting] - [Alter Settings Individually].
% The sound type and volume can not be set for the item where the [Sound Setting] is set to [No].

5.6 Other
5
[Operation Con- [Input Confirmation Set the sound type and volume to output when a key is
firmation Sound] Sound] pressed on the Control Panel or Touch Panel. Select
the sound type from six types and select the sound vol-
ume from [High], [Medium], or [Low] for adjustment.
[Invalid Sound] Set the sound type and volume when a key pressed on
the Control Panel or Touch Panel is invalid. Select the
sound type from six types and select the sound volume
from [High], [Medium], or [Low] for adjustment.
[Basic Sound] Set the sound type and volume to output when the de-
fault option is selected from a list of options where one
is selected in rotation. Select the sound type from six
types and select the sound volume from [High], [Medi-
um], or [Low] for adjustment.
[Window Pop-Up Sound] Set the sound type and volume when Island Window or
Balloon Window is opened. Select the sound type from
six types and select the sound volume from [High], [Me-
dium], or [Low] for adjustment.
Chapter 5
[Keyboard Operation Set the sound type and volume when Keyboard screen
Sound] or Keypad is operated. Select the sound type from six
[Successful Com- [Operation Complete Set the sound type and volume when an operation has

pletion Sound] Sound] ended normally. Select the sound type from six types
and select the sound volume from [High], [Medium], or
[Low] for adjustment.
[Transmission Complete Set the sound type and volume when a communication
Sound] has ended normally. Select the sound type from six
[Print Job Complete Set the sound type and volume when printing in PC is
Sound] normally completed. Select the sound type from six
[Fax RX Print Complete Set the sound type and volume when printing for re-
Sound] ceived Fax is normally completed. Select the sound
type from six types and select the sound volume from
[High], [Medium], or [Low] for adjustment.
[Completed Preparation Sound] Set the sound type and volume when the preparation of
this machine has completed. Select the sound type
from six types and select the sound volume from [High],
[Medium], or [Low] for adjustment.
[Caution Sound] [Low Caution Sound Set the volume of sound output when a message is dis-
(Level 1)] played on the Touch Panel indicating that the replace-
ment time is nearing for supplies or replaceable parts.
Select the sound type from six types and select the
sound volume from [High], [Medium], or [Low] for ad-
justment.
[Low Caution Sound Set the sound type and volume when the user has
(Level 2)] made a mistake while operating this machine. Select
[Low Caution Sound Set the sound type and volume when an error has oc-
(Level 3)] curred that can be addressed by referring to the mes-
sage on the screen or instructions in the manual. Select
[Severe Caution Sound] Specify the sound type and volume when a Toner Car-
tridge or Waste Toner Box installation failure or an er-
ror to be addressed by a service representative has
occurred. Select the sound type from six types and se-
lect the sound volume from [High], [Medium], or [Low]
for adjustment.

Other 5.6
5
[Deletion Sound] Set the sound type and volume when Document or Job
is deleted. Select the sound type from six types and se-
lect the sound volume from [High], [Medium], or [Low]
for adjustment.
[Authentication [Authentication Success- Tap [Login] or [Access] on the Login screen, then spec-
Sound] ful Sound] ify the sound type and volume when user authentica-
tion or account track has succeeded. Select the sound
type from six types and select the sound volume from
[High], [Medium], or [Low] for adjustment.
[Authentication Failure Tap [Login] or [Access] on the Login screen, then spec-
Sound] ify the sound type and volume when user authentica-
tion or account track has failed. Select the sound type
from six types and select the sound volume from [High],
[Medium], or [Low] for adjustment.
6 Select the sound type and volume, then tap [OK].

Chapter 5
Tips
- If an Android/iOS tablet terminal is connected to this machine, [Device Sound] is displayed as a sound
type option. Tapping [Device Sound] enables you to specify the tablet terminal output sound from the
list of device sound files.
- When [Operation Confirmation Sound] - [Window Pop-Up Sound] is set to [On], no sound is output if
the pop-up window is not displayed in animation view. For details, refer to the User’s Guide CD.
5.6.4 Q4. User authentication seems to be enabled on this machine. How can I be
authenticated and allowed to operate this machine?
A4. Check with the administrator whether you are a user registered in this machine.
If you are a registered user, obtain the user name and password from the administrator, perform user authen-
tication using this machine or printer driver, and log in to this machine.
Otherwise, log in to this machine with public users' privileges.

5.6 Other
5
How to set: Getting authenticated as a user on this machine
% Enter the [User Name] and [Password] registered in this machine and tap [Login]. When successfully
authenticated, you are allowed to operate this machine.
Chapter 5
How to set: Getting authenticated as a user on the printer driver

3 On the [Basic] tab, click [Authentication/Account Track].

Other 5.6
5
4 Select [Recipient User], enter the [User Name] and [Password] that are registered in the machine, then
click [OK].
Chapter 5
5 Click [OK].
6 Click [Print].
After successful user authentication, the file is printed.
5.6.5 Q5. The power is input all day. Is there any way to alleviate concerns about
electricity charges?
A5. If no operation takes place for a certain period of time, the power-saving function starts automatically,
and the machine enters the power-saving mode.
Using the weekly timer function automatically switches this machine to the normal mode and power save
mode at the pre-specified time.
The weekly timer function provides the following functions:
Function Description
[Time Settings] Specify the time for switching to the power save mode and the time for re-
turning to the normal mode for each day of the week. For example, you can
set it up so that the power turns off at the close of business on work days
and omit settings for weekends since no one uses the machine.
[Date Settings] Configure the days you want to apply the weekly timer to one by one. This
function is useful when the schedule for holidays is irregular or when this
machine must be powered on or off on a specific day regardless of the set-
ting in [Timer Settings].

5.6 Other
5
Function Description
[Select Time for Power Specify the time period to temporarily switch to the power save mode. This
Save] allows you to temporarily switch to the power save mode in the time period
such as a lunch break in which this machine is inactive.
[Password for Non-Busi- Using the weekly timer restricts the use of this machine in the Power Save
ness Hours] mode with a password.
How to set
3 Select [System Settings] - [Weekly Timer Settings] - [Weekly Timer ON/OFF Settings].
4 Select [ON], select [ErP Auto Power OFF] or [Sleep], then tap [OK].
% Select [ErP Auto Power OFF] when there is no need to receive a job in the power save mode and
Chapter 5
you wish to cut off power consumption whenever you can.
% Select [Sleep] if a Fax Kit is installed and you need to receive a job even in the power save mode.

5 Tap [Time Settings].
6 Select a day of the week you want to set the weekly timer to, enter the ON and OFF times using the
keypad, then tap [OK].
% To erase the time you have specified, tap [ ][ ] to select the target time, then tap [Delete].
% Select the day of the week for which you have specified the times, then tap [Set All], and the settings
will be applied to all the other days of the week.

Other 5.6
5
7 To specify the timer date by date, tap [Date Settings].
8 Select a year and a month in [Year] and [Monthly], select dates on the calendar, then tap [OK].
% You can also use the batch setting by tapping [ON] or [OFF] in the Daily Setting section.
Chapter 5
9 To switch to the power save mode temporarily, such as during a lunch break, tap [Select Time for Power
Save].
10 Tap [Yes], enter the time period to switch to the power save mode using the Keypad, then tap [OK].
11 When using the weekly timer to restrict the use of this machine in the Power Save mode with a pass-
word, tap [Password for Non-Business Hours].

5.6 Other
5
12 Select [Yes], enter the password, then tap [OK].
Chapter 5
5.6.6 Q6. What action should be taken if the administrator password is lost?
A6. The administrator password is set to [1234567812345678] by factory default. Try this password if the ad-
ministrator password has not been changed.
If it has been changed, contact your service representative.

Other 5.6
5
Chapter 5

6
Troubleshooting
Troubleshooting Chapter 6
Main Messages and Remedies 6.1
6
6 Troubleshooting
6.1 Main Messages and Remedies
6.1.1 When a Message Appears to Replace Consumables or Carry Out Cleaning

A message appears indicating the time(s) that expiring consumables used in this machine should be re-
placed. Also, a message appears when the Slit Scan Glass is dirty.
Replace consumables mentioned in the displayed message or clean the Slit Scan Glass.
Chapter 6
Troubleshooting
A message recommending that parts be replaced indicates that certain consumables are running out. Al-
though you can still continue to print for a while after the message is displayed, it is advisable to promptly
prepare replacement consumables.
- For a Toner Cartridge: [Toner is low. Replace when indicated.] appears, followed by [Replace Toner
Cartridge.]. Replace the Toner Cartridge based on the maintenance contract.
- For Waste Toner Box: When the message [Waste Toner Box needs to be replaced.] appears, contact
your service representative.
Contact your service representative if the messages continue to appear even after replacement or cleaning
has been carried out.

6
6.1.2 When a paper jam message persists
There may be a paper jam occurring in sections other than those indicated on the Touch Panel. Check the
sections again not shown on the Touch Panel.
Check the following items:

- Check for any pieces of paper left in the back of the section indicated on the Touch Panel. If the paper
cannot be easily removed, do not continue; instead contact your service representative.
Chapter 6
- Once again, open and close the door at the section with the location number indicated on the Touch
Panel. This action may clear the message.
Contact your service representative if the paper jam indication persists even after you have checked.
Troubleshooting

Main Messages and Remedies 6.1
6
6.1.3 When an error message appears
When an error is detected, the following message appears. Take the appropriate action according to the
message displayed on the screen. If you cannot resolve the error, write down the [Trouble Code], and contact
your service representative with the power plug disconnected from the power outlet.
In normal circumstances, the phone number and fax number for your service representative appear in the
center of the screen.
Chapter 6
NOTICE
If a defective part can be separated in order to be able to continue operations after a problem has been de-
tected, [Continue] or [Recover Data] is displayed. To continue operations, select any key. However, the prob-
lem has not been resolved, so contact your service representative immediately.
Troubleshooting

6
6.1.4 When [Stabilizing image.] appears
This automatically performs a function to adjust printing quality in order to maintain a certain level of color
reproduction quality. This "printing quality adjustment" is referred to as "image stabilization".
Image stabilization is performed while a large number of copies are being output or the temperature or hu-
midity inside the machine has changed.
Upon completion of image stabilization, printing is automatically resumed. Wait for a moment.
Chapter 6
In case image stabilization does not finish after a short while, contact your service representative.
NOTICE
You cannot interrupt or prohibit image stabilization.
d Reference
Troubleshooting
To perform image stabilization on a voluntary basis, refer to the User’s Guide CD.

When Printing Quality Has Deteriorated 6.2
6
6.2 When Printing Quality Has Deteriorated
6.2.1 Cleaning the Electrostatic Charger Wire

If the Electrostatic Charger Wire is dirty, linear smudges may appear on a print image. If this occurs, clean
the Electrostatic Charger Wire according to the following procedure.
1 Open the Lower Front Door or Front Door of the machine.
2 Carefully pull out the Charger Cleaner towards yourself up to

the position at which it stops. Then, carefully press it against
Chapter 6
the back side.

% Repeat the steps above three times.
Troubleshooting
3 Securely press the Charger Cleaner, and close the Lower Front Door or Front Door of the machine.

6.2 When Printing Quality Has Deteriorated
6
6.2.2 Cleaning the Print Head Glass
Printing quality deteriorates if the Print Head Glass is dirty. If this occurs, clean the Print Head Glass ac-
cording to the following procedure.
1 Open the Lower Front Door or Front Door of the machine.
2 Release the Waste Toner Box Lock Lever, then remove the
Waste Toner Box.
Chapter 6
Troubleshooting
3 Remove the Printhead Cleaner from the Lower Front Door
or Front Door of this machine.
4 Slowly insert the Printhead Cleaner all the way to the back
end of the Print Head Glass section, and then slowly pull it
out.
% Repeat this operation approximately three times for all of
the Print Head Glass sections.
5 Mount the Printhead Cleaner onto the Lower Front Door or Front Door of this machine.

When Printing Quality Has Deteriorated 6.2
6
6 Install the Waste Toner Box.
7 Close the Lower Front Door or Front Door of the machine.

Chapter 6
Troubleshooting

6.3 When the Machine Cannot Be Powered On
6
6.3 When the Machine Cannot Be Powered On
This machine has two power sources. Check the Main Power Switch and the Power key for the status.
- Check whether the power plug of this machine is firmly plugged into the power outlet. Also check that
the breaker has not tripped.
- Check to see that the Main Power Switch and the Power key are turned ON.
Chapter 6
In case the machine cannot be powered on even after checking, contact your service representative.
Troubleshooting

When the Touch Panel Is Not Visible 6.4
6
6.4 When the Touch Panel Is Not Visible
If a certain length of time has elapsed without any operations being carried out on this machine, the Touch
Panel may turn off.
Check the following items:
- Tap [Accessibility] and select [Brightness Adjustment], and select [Low] or [High] to adjust the contrast
for the Touch Panel.
Chapter 6
- Touch the Touch Panel. In Power Save (Low Power/Sleep) mode, this machine returns from Power
Save mode when the Touch Panel is touched or a key on the Control Panel is pressed, and the Touch
Panel appears normally.
- On the Control Panel, press the Power key. If the Weekly Timer setting has put the machine in Erp
Auto Power OFF mode, press the Power key to display the Touch Panel. To use it outside the preset
Troubleshooting
operating hours, follow the on-screen instructions.

6.4 When the Touch Panel Is Not Visible
6
- Check to see that the Main Power Switch and the Power key are turned ON.
In case the Touch Panel does not appear even after checking it, contact your service representative.
Chapter 6
Troubleshooting

When a Message Appears to Replace Consumables or Carry Out Cleaning 6.5
6
6.5 When a Message Appears to Replace Consumables or Carry Out
Cleaning
When staples in the finisher have run out

When staples in the Finisher have run out, the following message appear.
Take action while referring to the label inside the machine.
Chapter 6
When the punch scrap box is full

When the punch scrap box is full, the following message appears (at replacement by user).
Take action while referring to the label inside the machine.
Troubleshooting

6.5 When a Message Appears to Replace Consumables or Carry Out Cleaning
6
When toner is running out in the Toner Cartridge
When toner is running out in Toner Cartridge, a message appears as shown below (at replacement by user).
When a Waste Toner Box is full

When the Waste Toner Box is full, the following message appears (at replacement by user). Tap [Start Guid-
ance], then follow the displayed guidance to take an action.
Chapter 6
Troubleshooting

6
6.5.1 Replacing a Toner Cartridge
bizhub C554e/C454e
The following example shows how to replace a Yellow Toner Cartridge.
2 7
3 6
Chapter 6
Troubleshooting
4 5
Tips
- Shake a new Toner Cartridge well, approximately 5 to 10 times, before installing it.
- If a Toner Cartridge other than for black is empty, printing can be continued forcibly using black. Tap
[Continue], and then select a desired print job.
- Do not forcedly open or disassemble a Toner Cartridge (toner container).
- Do not forcedly remove or dispose of toner that remains in a Toner Cartridge (toner container).
- After replacing a Toner Cartridge, be sure to clean the Electrostatic Charger Wire that corresponds
to the replaced color. For details on how to clean the Electrostatic Charger Wire, refer to page 6-6.
NOTICE
Install a Toner Cartridge for each label color. If you try to forcibly install a Toner Cartridge in the incorrect
position, it may result in a failure.
7 CAUTION
Handling toner and Toner Cartridge
- Do not throw a toner or Toner Cartridge into a fire. Doing so may cause hot toner to spray in all direc-
tions, which may cause burn injuries.
- Be careful not to get the inside of the machine, your clothes, or hands dirty with toner.
- If any toner gets on your hands, wash it off using water or neutral detergent.
- If any toner gets into your eyes, immediately wash it out with water and consult your doctor.

6
The following example shows how to replace a Yellow Toner Cartridge.
1 5
2 3
Chapter 6
Troubleshooting
Tips
- Shake a new Toner Cartridge well, approximately 5 to 10 times, before installing it.
- If a Toner Cartridge other than for black is empty, printing can be continued forcibly using black. Tap
[Continue], and then select a desired print job.
- Do not forcedly open or disassemble a Toner Cartridge (toner container).
- Do not forcedly remove or dispose of toner that remains in a Toner Cartridge (toner container).
- After replacing a Toner Cartridge, be sure to clean the Electrostatic Charger Wire that corresponds
to the replaced color. For details on how to clean the Electrostatic Charger Wire, refer to page 6-6.
NOTICE
Install a Toner Cartridge for each label color. If you try to forcibly install a Toner Cartridge in the incorrect
position, it may result in a failure.
7 CAUTION
Handling toner and Toner Cartridge
- Do not throw a toner or Toner Cartridge into a fire. Doing so may cause hot toner to spray in all direc-
tions, which may cause burn injuries.
- If any toner does get on your hand, wash it off using water or neutral detergent.

6
6.5.2 Replacing a Waste Toner Box
bizhub C554e/C454e
3
Chapter 6
4
Troubleshooting
Tips
- Your service representative will recover your used Waste Toner Box. Place a cap on it and store it in
a box.
- After replacing a Waste Toner Box, be sure to clean the Electrostatic Charger Wire for each color.
For details on how to clean the Electrostatic Charger Wire, refer to page 6-6.
7 CAUTION
Handling toner and Waste Toner Box
- Do not throw a toner or Waste Toner Box into a fire. Doing so may cause hot toner to spray in all di-
rections, which may cause burn injuries.
- If any toner gets on your hands, wash it off using water or neutral detergent.

6
Chapter 6
4
Troubleshooting
5
Tips
- Your service representative will recover your used Waste Toner Box. Place a cap on it and store it in
a box.
- After replacing a Waste Toner Box, be sure to clean the Electrostatic Charger Wire for each color.
For details on how to clean the Electrostatic Charger Wire, refer to page 6-6.
7 CAUTION
Handling toner and Waste Toner Box
- Do not throw a toner or Waste Toner Box into a fire. Doing so may cause hot toner to spray in all di-
rections, which may cause burn injuries.
- If any toner does get on your hand, wash it off using water or neutral detergent.

6
Chapter 6
Troubleshooting

7
Index
Index Chapter 7
Index by item 7.1
7
7 Index
7.1 Index by item

A PS ................................................................................ 3-8
Address Book ............................................................3-62 R
Advanced Functions ...................................................4-2
Request Code ............................................................. 4-4
C S
Control Panel .............................................................2-29
Safety information ....................................................... 1-5
Copy function ............................................................3-59
Saving the scanned data .......................................... 3-77
D Search ....................................................................... 3-71
Dialing Method ..........................................................3-49 Sender Fax No. Settings ........................................... 3-48
Sender settings ......................................................... 3-48
E Sleep mode ............................................................... 2-27
E-mail TX ...................................................................3-40 SMB Send ....................................................... 3-20, 3-30
Entering Characters ..................................................2-37 Sub Power OFF ......................................................... 2-27
ErP Auto Power OFF .................................................2-28
T
F Token Certificate ......................................................... 4-4
Fax TX .......................................................................3-46 Touch Panel .................................................... 2-31, 2-32
G U
Chapter 7
Group ........................................................................3-69 User authentication ................................................... 3-61

Guidance function .....................................................3-81
V
I Voice Guidance ........................................................... 4-9
Installing the fax driver ..............................................3-55
X
Index
Installing the printer driver .................................3-4, 3-12

i-Option .......................................................................4-3 XPS ............................................................................. 3-8
J
Job ............................................................................2-38
K
Keypad ......................................................................2-36
L
License Management Server (LMS) ............................4-4
Loading Paper ............................ 2-39, 2-40, 2-41, 2-42
Low Power mode ......................................................2-27
M
Main Menu .................................................................2-31
MFP .................................................................2-12, 2-14
Multi-job ....................................................................2-38
O
Options ......................................................2-6, 2-9, 2-16
P
PC-Fax TX .................................................................3-52
PCL ..............................................................................3-8
Power Save mode .....................................................2-27
Print Function ......................................................3-2, 3-9
Printing from a USB memory device .........................3-74

http://konicaminolta.com
Printed in China
A5AY-9564-01 © 2013 2013. 4

Bizhubc554e C454e C364e C284e C224eQuickStartGuide

Uploaded by

Copyright:

Available Formats

Bizhubc554e C454e C364e C284e C224eQuickStartGuide

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Bizhubc554e C454e C364e C284e C224eQuickStartGuide

Uploaded by

Copyright:

Available Formats

Quick Start Guide

This manual describes basic procedures users will need to know in

bizhub C554e/C454e/C364e/C284e/C224e Contents-1

Contents-2 bizhub C554e/C454e/C364e/C284e/C224e

3 Basic Settings and Operations

bizhub C554e/C454e/C364e/C284e/C224e Contents-3

Contents-4 bizhub C554e/C454e/C364e/C284e/C224e

5 Frequently Asked Questions

bizhub C554e/C454e/C364e/C284e/C224e Contents-5

Contents-6 bizhub C554e/C454e/C364e/C284e/C224e

1.1 Environmental Information

What is an ENERGY STAR® Product?

Environmental benefits of power management

1-2 bizhub C554e/C454e/C364e/C284e/C224e

bizhub C554e/C454e/C364e/C284e/C224e 1-3

This product is certified by the following model name in U.S.A.

1-4 bizhub C554e/C454e/C364e/C284e/C224e

Warning and precaution symbols

CAUTION Ignoring this caution could cause injury or damage to property.

A triangle indicates a danger against which you should take precaution.

Disassemble and modification

bizhub C554e/C454e/C364e/C284e/C224e 1-5

• Do not use a multiple outlet adapter to connect any other appliances or

1-6 bizhub C554e/C454e/C364e/C284e/C224e

• Do not place the product in a dusty place, or a site exposed to soot or

bizhub C554e/C454e/C364e/C284e/C224e 1-7

Actions in response to troubles

When moving the machine

When using the machine

1-8 bizhub C554e/C454e/C364e/C284e/C224e

When the Fax is not installed:

Before successive holidays

bizhub C554e/C454e/C364e/C284e/C224e 1-9

1.4 Regulation notices

CE Marking (Declaration of Conformity) for users of the European Union (EU)

This product complies with the following EU directives:

USER INSTRUCTIONS FCC PART 15 - RADIO FREQUENCY DEVICES (for

INTERFERENCE-CAUSING EQUIPMENT STANDARD (ICES-003 ISSUE 4) (for

For users in countries not subject to class B regulations

1-10 bizhub C554e/C454e/C364e/C284e/C224e

For European users

bizhub C554e/C454e/C364e/C284e/C224e 1-11

For Denmark users

For Finland, Sweden users

For Norway users

1-12 bizhub C554e/C454e/C364e/C284e/C224e

Only for the U.S.A.

Only for the Europe Only for the Europe

Acoustic noise (for European users only)

Notification for California Customers

bizhub C554e/C454e/C364e/C284e/C224e 1-13

For EU member states only

For EU member states only

Telephone Cable (For users in countries subject to class B regulations)

1-14 bizhub C554e/C454e/C364e/C284e/C224e

bizhub C554e/C454e/C364e/C284e/C224e 1-15

1.6 Special Notice to User

This equipment uses certification jack USOC RJ11C.

1-16 bizhub C554e/C454e/C364e/C284e/C224e