[ 0.

000000] Booting Linux on physical CPU 0x0

[ 0.000000] Linux version 4.14.98-35-boundary-17b (debian-
kernel@lists.debian.org) (gcc version 8.3.0 (Debian 8.3.0-2)) #1 SMP PREEMPT Debian
4.14.98-35.35 (2022-02-03)
[ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction
cache
[ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Reserved memory: created CMA memory pool at 0x3c000000, size 320 MiB
[ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-
dma-pool
[ 0.000000] On node 0 totalpages: 262144
[ 0.000000] free_area_init_node: node 0, pgdat 80f6cb00, node_mem_map ab657000
[ 0.000000] Normal zone: 2304 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 262144 pages, LIFO batch:31
[ 0.000000] random: get_random_bytes called from start_kernel+0xa4/0x42c with
crng_init=0
[ 0.000000] percpu: Embedded 16 pages/cpu @ab5ef000 s35788 r8192 d21556 u65536
[ 0.000000] pcpu-alloc: s35788 r8192 d21556 u65536 alloc=16*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 259840
[ 0.000000] Kernel command line: console=ttymxc1,115200 vmalloc=400M
consoleblank=0 rootwait fixrtc cpu=6Q board=sabrelite systemd.gpt_auto=0
root=/dev/mmcblk1p1 splash plymouth.ignore-serial-consoles loglevel=4
reset_cause=0x10 snd.slots=,snd-soc-imx-hdmi
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 690040K/1048576K available (10240K kernel code, 439K rwdata,
2580K rodata, 1024K init, 463K bss, 30856K reserved, 327680K cma-reserved, 0K
highmem)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xc0800000 - 0xff800000 (1008 MB)
lowmem : 0x80000000 - 0xc0000000 (1024 MB)
pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
.text : 0x80008000 - 0x80b00000 (11232 kB)
.init : 0x80e00000 - 0x80f00000 (1024 kB)
.data : 0x80f00000 - 0x80f6dc60 ( 440 kB)
.bss : 0x80f6f000 - 0x80fe2cc8 ( 464 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] L2C-310 errata 752271 769419 enabled
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB
[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001
[ 0.000000] Switching to timer-based delay loop, resolution 333ns
[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every
715827882841ns
[ 0.000022] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff,
max_idle_ns: 637086815595 ns
[ 0.001844] Console: colour dummy device 80x30
[ 0.001865] Calibrating delay loop (skipped), value calculated using timer
frequency.. 6.00 BogoMIPS (lpj=30000)
[ 0.001880] pid_max: default: 32768 minimum: 301
[ 0.002019] Security Framework initialized
[ 0.002027] Yama: becoming mindful.
[ 0.002092] AppArmor: AppArmor initialized
[ 0.002149] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.002169] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.002867] CPU: Testing write buffer coherency: ok
[ 0.002898] CPU0: Spectre v2: using BPIALL workaround
[ 0.003322] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.039596] Setting up static identity map for 0x10100000 - 0x10100060
[ 0.059530] Hierarchical SRCU implementation.
[ 0.099530] smp: Bringing up secondary CPUs ...
[ 0.169793] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.169799] CPU1: Spectre v2: using BPIALL workaround
[ 0.239783] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.239788] CPU2: Spectre v2: using BPIALL workaround
[ 0.309783] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.309790] CPU3: Spectre v2: using BPIALL workaround
[ 0.309922] smp: Brought up 1 node, 4 CPUs
[ 0.309931] SMP: Total of 4 processors activated (24.00 BogoMIPS).
[ 0.309938] CPU: All CPU(s) started in SVC mode.
[ 0.310914] devtmpfs: initialized
[ 0.322890] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9
rev 4
[ 0.323166] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff,
max_idle_ns: 19112604462750000 ns
[ 0.323185] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.341086] xor: measuring software checksum speed
[ 0.439524] arm4regs : 1224.000 MB/sec
[ 0.539510] 8regs : 964.800 MB/sec
[ 0.639510] 32regs : 981.200 MB/sec
[ 0.639517] xor: using function: arm4regs (1224.000 MB/sec)
[ 0.639535] pinctrl core: initialized pinctrl subsystem
[ 0.640558] NET: Registered protocol family 16
[ 0.669657] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.670645] cpuidle: using governor menu
[ 0.671022] CPU identified as i.MX6Q, silicon rev 1.2
[ 0.681246] vdd1p1: supplied by regulator-dummy
[ 0.681840] vdd3p0: supplied by regulator-dummy
[ 0.682357] vdd2p5: supplied by regulator-dummy
[ 0.682928] vddarm: supplied by regulator-dummy
[ 0.683481] vddpu: supplied by regulator-dummy
[ 0.684051] vddsoc: supplied by regulator-dummy
[ 0.698347] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint
registers.
[ 0.698356] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.699582] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
[ 0.702073] imx rpmsg driver is registered.
[ 0.879731] raid6: int32x1 gen() 105 MB/s
[ 1.049514] raid6: int32x1 xor() 141 MB/s
[ 1.219622] raid6: int32x2 gen() 148 MB/s
[ 1.389672] raid6: int32x2 xor() 162 MB/s
[ 1.559698] raid6: int32x4 gen() 189 MB/s
[ 1.729674] raid6: int32x4 xor() 173 MB/s
[ 1.899621] raid6: int32x8 gen() 214 MB/s
[ 2.069709] raid6: int32x8 xor() 147 MB/s
[ 2.069717] raid6: using algorithm int32x8 gen() 214 MB/s
[ 2.069723] raid6: .... xor() 147 MB/s, rmw enabled
[ 2.069729] raid6: using intx1 recovery algorithm
[ 2.084416] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 28, base_baud =
5000000) is a IMX
[ 2.085278] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 75, base_baud =
5000000) is a IMX
[ 2.085325] console [ttymxc1] enabled
[ 2.086645] SCSI subsystem initialized
[ 2.086886] libata version 3.00 loaded.
[ 2.087128] usbcore: registered new interface driver usbfs
[ 2.087181] usbcore: registered new interface driver hub
[ 2.087280] usbcore: registered new device driver usb
[ 2.087510] usb_phy_generic 2000000.aips-bus:usbphy_nop1: 2000000.aips-
bus:usbphy_nop1 supply vcc not found, using dummy regulator
[ 2.087709] usb_phy_generic 2000000.aips-bus:usbphy_nop2: 2000000.aips-
bus:usbphy_nop2 supply vcc not found, using dummy regulator
[ 2.088523] imx-i2c 21a0000.i2c: stop-delay=0, inter-byte-delay=0
[ 2.088882] i2c i2c-0: IMX I2C adapter registered
[ 2.088898] i2c i2c-0: can't use DMA, using PIO instead.
[ 2.089269] imx-i2c 21a4000.i2c: stop-delay=0, inter-byte-delay=0
[ 2.090011] i2c i2c-1: IMX I2C adapter registered
[ 2.090027] i2c i2c-1: can't use DMA, using PIO instead.
[ 2.090418] imx-i2c 21a8000.i2c: stop-delay=0, inter-byte-delay=0
[ 2.091570] i2c i2c-2: IMX I2C adapter registered
[ 2.091585] i2c i2c-2: can't use DMA, using PIO instead.
[ 2.092073] Linux video capture interface: v2.00
[ 2.092154] pps_core: LinuxPPS API ver. 1 registered
[ 2.092160] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
<giometti@linux.it>
[ 2.092179] PTP clock support registered
[ 2.119821] imx-ipuv3 2400000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5),
5F(6,7)
[ 2.149812] imx-ipuv3 2800000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5),
5F(6,7)
[ 2.151032] mxc_vdoa 21e4000.vdoa: i.MX Video Data Order Adapter(VDOA) driver
probed
[ 2.151940] mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 driver probed
[ 2.151950] mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 dphy version is
0x3130302a
[ 2.152076] MIPI CSI2 driver module loaded
[ 2.152448] Advanced Linux Sound Architecture Driver Initialized.
[ 2.153580] Bluetooth: Core ver 2.22
[ 2.153621] NET: Registered protocol family 31
[ 2.153627] Bluetooth: HCI device and connection manager initialized
[ 2.153642] Bluetooth: HCI socket layer initialized
[ 2.153660] Bluetooth: L2CAP socket layer initialized
[ 2.153705] Bluetooth: SCO socket layer initialized
[ 2.153725] NetLabel: Initializing
[ 2.153730] NetLabel: domain hash size = 128
[ 2.153736] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 2.153815] NetLabel: unlabeled traffic allowed by default
[ 2.154552] clocksource: Switched to clocksource mxc_timer1
[ 2.154737] VFS: Disk quotas dquot_6.6.0
[ 2.154823] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.155447] AppArmor: AppArmor Filesystem Enabled
[ 2.166159] NET: Registered protocol family 2
[ 2.166834] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 2.166918] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 2.167062] TCP: Hash tables configured (established 8192 bind 8192)
[ 2.167281] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 2.167325] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 2.167534] NET: Registered protocol family 1
[ 2.168061] RPC: Registered named UNIX socket transport module.
[ 2.168068] RPC: Registered udp transport module.
[ 2.168073] RPC: Registered tcp transport module.
[ 2.168079] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.168091] PCI: CLS 0 bytes, default 64
[ 2.168357] Trying to unpack rootfs image as initramfs...
[ 2.456666] Freeing initrd memory: 4448K
[ 2.457390] hw perfevents: no interrupt-affinity property for /soc/pmu,
guessing.
[ 2.457744] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters
available
[ 2.460251] Bus freq driver module loaded
[ 2.461228] audit: initializing netlink subsys (disabled)
[ 2.461524] audit: type=2000 audit(2.450:1): state=initialized audit_enabled=0
res=1
[ 2.461921] Key type blacklist registered
[ 2.462162] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[ 2.467584] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.468727] NFS: Registering the id_resolver key type
[ 2.468758] Key type id_resolver registered
[ 2.468764] Key type id_legacy registered
[ 2.468991] fuse init (API version 7.26)
[ 2.477163] io scheduler noop registered
[ 2.477172] io scheduler deadline registered
[ 2.477342] io scheduler cfq registered (default)
[ 2.477350] io scheduler mq-deadline registered
[ 2.477359] io scheduler kyber registered
[ 2.479628] imx6q-pcie 1ffc000.pcie: no reserved region node.
[ 2.479680] imx6q-pcie 1ffc000.pcie: 1ffc000.pcie supply epdev_on not found,
using dummy regulator
[ 2.480046] OF: PCI: host bridge /soc/pcie@1ffc000 ranges:
[ 2.480083] OF: PCI: IO 0x01f80000..0x01f8ffff -> 0x00000000
[ 2.480103] OF: PCI: MEM 0x01000000..0x01efffff -> 0x01000000
[ 2.688786] imx6q-pcie 1ffc000.pcie: phy link never came up
[ 2.696141] imx6q-pcie 1ffc000.pcie: failed to initialize host
[ 2.700679] imx6q-pcie 1ffc000.pcie: unable to add pcie port.
[ 2.705377] imx6q-pcie: probe of 1ffc000.pcie failed with error -110
[ 2.708734] ldb 2000000.aips-bus:ldb: failed to find valid LVDS channel
[ 2.714087] ldb: probe of 2000000.aips-bus:ldb failed with error -22
[ 2.714941] mxc_hdmi 20e0000.hdmi_video: 20e0000.hdmi_video supply HDMI not
found, using dummy regulator
[ 2.715938] mxc_hdmi 20e0000.hdmi_video: Detected HDMI controller
0x13:0xa:0xa0:0xc1
[ 2.715963] fbcvt: 1920x1080@60: CVT Name - 2.073M9
[ 2.716092] mxc_sdc_fb fb@2: registered mxc display driver hdmi
[ 2.762374] mxc_sdc_fb fb@2: 1920x1080 h_sync,r,l: 44,88,148 v_sync,l,u: 5,4,36
pixclock=148500000 Hz
[ 2.762526] imx-ipuv3 2800000.ipu: try ipu internal clk
[ 2.784598] imx-ipuv3 2800000.ipu: disp=0, pixel_clk=148500000 148500000
parent=148500000 div=1
[ 2.784611] find_field: [0] = 0x7ff, max=23
[ 2.784617] find_field: [1] = 0xfff, max=23
[ 2.784624] find_field: [2] = 0x17ff, max=23
[ 2.784630] find_field: [0] = 0x820, max=29
[ 2.784676] imx-ipuv3 2800000.ipu: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5),
5F(6,7)
[ 2.818112] mxc_sdc_fb fb@2: 1920x1080 h_sync,r,l: 44,88,148 v_sync,l,u: 5,4,36
pixclock=148500000 Hz
[ 2.818240] imx-ipuv3 2800000.ipu: try ipu internal clk
[ 2.844597] imx-ipuv3 2800000.ipu: disp=0, pixel_clk=148500000 148500000
parent=148500000 div=1
[ 2.885785] Console: switching to colour frame buffer device 240x67
[ 2.933249] add tfp410 i2c driver
[ 2.935068] imx-sdma 20ec000.sdma: no iram assigned, using external mem
[ 2.935929] imx-sdma 20ec000.sdma: loaded firmware 3.5
[ 2.939855] mxs-dma 110000.dma-apbh: initialized
[ 2.941951] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to
20dc000.gpc
[ 2.942262] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to
20dc000.gpc
[ 2.945762] imx sema4 driver is registered.
[ 2.946896] spi_imx 2008000.ecspi: probed
[ 2.948053] [drm] Initialized vivante 1.0.0 20120216 for platform:Vivante GCCore
on minor 0
[ 2.948062] [drm] Initialized vivante 1.0.0 20120216 on minor 0
[ 2.959149] brd: module loaded
[ 2.974130] loop: module loaded
[ 2.974306] [max77823_init] start
[ 2.976142] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using
00000024
[ 2.976154] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using
00000480
[ 2.976164] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using
00002000
[ 2.976173] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using
05000000
[ 2.980771] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled
[ 2.980803] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1
impl platform mode
[ 2.980816] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio
slum part ccc apst
[ 2.982713] scsi host0: ahci-imx
[ 2.983017] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100
irq 82
[ 2.985769] m25p80 spi0.0: sst25vf016b (2048 Kbytes)
[ 2.985812] 3 ofpart partitions found on MTD device spi0.0
[ 2.985847] Creating 3 MTD partitions on "spi0.0":
[ 2.985860] 0x000000000000-0x0000000c0000 : "U-Boot"
[ 2.986473] random: fast init done
[ 2.987332] 0x0000000c0000-0x0000000c2000 : "env"
[ 2.988868] 0x0000000c2000-0x000000200000 : "splash"
[ 2.990967] libphy: Fixed MDIO Bus: probed
[ 2.991313] CAN device driver interface
[ 2.991736] flexcan 2090000.flexcan: 2090000.flexcan supply xceiver not found,
using dummy regulator
[ 2.992478] flexcan 2090000.flexcan: device registered (reg_base=c0b0c000,
irq=36)
[ 2.994074] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using
dummy regulator
[ 2.994536] pps pps0: new PPS source ptp0
[ 2.995205] mxc_sdc_fb fb@2: 1920x1080 h_sync,r,l: 44,88,148 v_sync,l,u: 5,4,36
pixclock=148500000 Hz
[ 2.995351] imx-ipuv3 2800000.ipu: try ipu internal clk
[ 2.996649] libphy: fec_enet_mii_bus: probed
[ 2.996662] mdio_bus 2188000.ethernet-1:
/soc/aips-bus@02100000/ethernet@02188000/mdio/ethernet-phy has invalid PHY address
[ 3.022733] fec 2188000.ethernet eth0: registered PHC device 0
[ 3.023175] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.023180] ehci-pci: EHCI PCI platform driver
[ 3.023296] usbcore: registered new interface driver cdc_acm
[ 3.023301] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN
adapters
[ 3.023359] usbcore: registered new interface driver usb-storage
[ 3.023465] usbcore: registered new interface driver usbserial
[ 3.023504] usbcore: registered new interface driver usbserial_generic
[ 3.023536] usbserial: USB Serial support registered for generic
[ 3.023571] usbcore: registered new interface driver cp210x
[ 3.023601] usbserial: USB Serial support registered for cp210x
[ 3.023636] usbcore: registered new interface driver ftdi_sio
[ 3.023666] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 3.023709] usbcore: registered new interface driver keyspan
[ 3.023746] usbserial: USB Serial support registered for Keyspan - (without
firmware)
[ 3.023779] usbserial: USB Serial support registered for Keyspan 1 port adapter
[ 3.023809] usbserial: USB Serial support registered for Keyspan 2 port adapter
[ 3.023840] usbserial: USB Serial support registered for Keyspan 4 port adapter
[ 3.023874] usbcore: registered new interface driver pl2303
[ 3.023903] usbserial: USB Serial support registered for pl2303
[ 3.023938] usbcore: registered new interface driver qcserial
[ 3.023967] usbserial: USB Serial support registered for Qualcomm USB modem
[ 3.024611] imx-ipuv3 2800000.ipu: disp=0, pixel_clk=148500000 148500000
parent=148500000 div=1
[ 3.035752] usbmisc_imx 2184800.usbmisc: 2184800.usbmisc supply vbus-wakeup not
found, using dummy regulator
[ 3.036934] setup_reset_gpios:-2, flags 0
[ 3.051659] setup_reset_gpios:204, flags 1
[ 3.058576] mxc_sdc_fb fb@2: 1920x1080 h_sync,r,l: 44,88,148 v_sync,l,u: 5,4,36
pixclock=148500000 Hz
[ 3.058722] imx-ipuv3 2800000.ipu: try ipu internal clk
[ 3.074585] setup_reset_gpios:-2, flags 1
[ 3.077997] ci_hdrc ci_hdrc.1: EHCI Host Controller
[ 3.078031] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
[ 3.084604] imx-ipuv3 2800000.ipu: disp=0, pixel_clk=148500000 148500000
parent=148500000 div=1
[ 3.104583] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[ 3.105403] hub 1-0:1.0: USB hub found
[ 3.105447] hub 1-0:1.0: 1 port detected
[ 3.117564] i2c /dev entries driver
[ 3.118268] IR NEC protocol handler initialized
[ 3.118274] IR RC5(x/sz) protocol handler initialized
[ 3.118277] IR RC6 protocol handler initialized
[ 3.118281] IR JVC protocol handler initialized
[ 3.118285] IR Sony protocol handler initialized
[ 3.118288] IR SANYO protocol handler initialized
[ 3.118291] IR Sharp protocol handler initialized
[ 3.118295] IR MCE Keyboard/mouse protocol handler initialized
[ 3.118299] IR XMP protocol handler initialized
[ 3.118910] mxc_v4l2_output v4l2-out: V4L2 device registered as video16
[ 3.119058] mxc_v4l2_output v4l2-out: V4L2 device registered as video17
[ 3.120057] check_alarm_past: alarm in the past
[ 3.120242] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered
20cc000.snvs:snvs-rtc-lp as rtc0
[ 3.122152] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
[ 3.122832] device-mapper: ioctl: 4.37.0-ioctl (2017-09-20) initialised: dm-
devel@redhat.com
[ 3.123912] sdhci: Secure Digital Host Controller Interface driver
[ 3.123916] sdhci: Copyright(c) Pierre Ossman
[ 3.123920] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.125099] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO
[ 3.125126] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO
[ 3.185853] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA
[ 3.186554] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO
[ 3.189377] mxc_sdc_fb fb@2: 640x480 h_sync,r,l: 96,16,48 v_sync,l,u: 2,10,33
pixclock=25175000 Hz
[ 3.189520] imx-ipuv3 2800000.ipu: try ipu internal clk
[ 3.214583] imx-ipuv3 2800000.ipu: disp=0, pixel_clk=25175000 25142857
parent=264000000 div=10
[ 3.244860] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA
[ 3.251661] mxc_vpu 2040000.vpu_fsl: VPU initialized
[ 3.255613] caam 2100000.caam: ERA source: CAAMVID.
[ 3.255683] caam 2100000.caam: AXI pipeline throttling enabled.
[ 3.256913] caam 2100000.caam: device ID = 0x0a16010000000000 (Era 4)
[ 3.256923] caam 2100000.caam: job rings = 2, qi = 0, dpaa2 = no
[ 3.259579] caam_jr 2101000.jr0: Entropy delay = 3200
[ 3.292275] mmc1: host does not support reading read-only switch, assuming
write-enable
[ 3.298341] mmc1: new high speed SDHC card at address 59b4
[ 3.299689] mmcblk1: mmc1:59b4 USDU1 15.0 GiB
[ 3.301333] mmcblk1: p1
[ 3.306212] ata1: SATA link down (SStatus 0 SControl 300)
[ 3.306265] ahci-imx 2200000.sata: no device found, disabling link.
[ 3.306274] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug
[ 3.320384] caam_jr 2101000.jr0: Instantiated RNG4 SH0.
[ 3.351955] mxc_sdc_fb fb@2: 1920x1080 h_sync,r,l: 44,88,148 v_sync,l,u: 5,4,36
pixclock=148500000 Hz
[ 3.352117] imx-ipuv3 2800000.ipu: try ipu internal clk
[ 3.374595] imx-ipuv3 2800000.ipu: disp=0, pixel_clk=148500000 148500000
parent=148500000 div=1
[ 3.381140] caam_jr 2101000.jr0: Instantiated RNG4 SH1.
[ 3.402744] caam algorithms registered in /proc/crypto
[ 3.407160] caam_jr 2101000.jr0: registering rng-caam
[ 3.408489] usbcore: registered new interface driver usbhid
[ 3.408494] usbhid: USB HID core driver
[ 3.411707] sgtl5000 0-000a: sgtl5000 revision 0x11
[ 3.413450] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1
[ 3.442587] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW
[ 3.443034] fsl-ssi-dai 202c000.ssi: No cache defaults, reading back from HW
[ 3.455994] imx-sgtl5000 sound: sgtl5000 <-> 2028000.ssi mapping ok
[ 3.457154] imx-sgtl5000 sound: ASoC: Cannot get gpio at index 0: -2
[ 3.457533] NET: Registered protocol family 26
[ 3.458215] NET: Registered protocol family 10
[ 3.459413] Segment Routing with IPv6
[ 3.459490] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 3.460111] NET: Registered protocol family 17
[ 3.460128] can: controller area network core (rev 20170425 abi 9)
[ 3.460231] NET: Registered protocol family 29
[ 3.460273] can: raw protocol (rev 20170425)
[ 3.460279] can: broadcast manager protocol (rev 20170425 t)
[ 3.460290] can: netlink gateway (rev 20170425) max_hops=1
[ 3.460563] Bluetooth: RFCOMM TTY layer initialized
[ 3.460580] Bluetooth: RFCOMM socket layer initialized
[ 3.460612] Bluetooth: RFCOMM ver 1.11
[ 3.460627] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 3.460632] Bluetooth: BNEP filters: protocol multicast
[ 3.460644] Bluetooth: BNEP socket layer initialized
[ 3.460701] 8021q: 802.1Q VLAN Support v1.8
[ 3.461082] Key type dns_resolver registered
[ 3.463241] Registering SWP/SWPB emulation handler
[ 3.465139] Btrfs loaded, crc32c=crc32c-generic
[ 3.465206] AppArmor: AppArmor sha1 policy hashing enabled
[ 3.480023] imx_thermal 2000000.aips-bus:tempmon: Automotive CPU temperature
grade - max:125C critical:120C passive:115C
[ 3.480608] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to 1970-01-
01 00:03:02 UTC (182)
[ 3.481473] usb_otg_vbus: disabling
[ 3.481478] ALSA device list:
[ 3.481483] #0: sgtl5000-audio
[ 3.484623] usb 1-1: new high-speed USB device number 2 using ci_hdrc
[ 3.562398] Freeing unused kernel memory: 1024K
[ 3.695949] hub 1-1:1.0: USB hub found
[ 3.696137] hub 1-1:1.0: 3 ports detected
[ 4.042303] input: gpio-keys as /devices/soc0/gpio-keys/input/input1
[ 4.584613] usb 1-1.1: new low-speed USB device number 3 using ci_hdrc
[ 4.619281] EXT4-fs (mmcblk1p1): mounted filesystem with ordered data mode.
Opts: (null)
[ 4.756658] input: ELMCU iPazzPort as
/devices/soc0/soc/2100000.aips-bus/2184200.usb/ci_hdrc.1/usb1/1-1/1-1.1/1-
1.1:1.0/0003:0C40:8000.0001/input/input2
[ 4.825395] hid-generic 0003:0C40:8000.0001: input: USB HID v1.11 Keyboard
[ELMCU iPazzPort] on usb-ci_hdrc.1-1.1/input0
[ 4.832489] input: ELMCU iPazzPort as
/devices/soc0/soc/2100000.aips-bus/2184200.usb/ci_hdrc.1/usb1/1-1/1-1.1/1-
1.1:1.1/0003:0C40:8000.0002/input/input3
[ 4.894799] hid-generic 0003:0C40:8000.0002: input: USB HID v1.11 Mouse [ELMCU
iPazzPort] on usb-ci_hdrc.1-1.1/input1
[ 5.526817] systemd[1]: System time before build time, advancing clock.
[ 5.580645] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 5.624424] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT
+SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL
+XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-
hierarchy=hybrid)
[ 5.626007] systemd[1]: Detected architecture arm.
[ 5.695760] systemd[1]: Set hostname to <buster-dev32>.
[ 5.944212] systemd[1]: File /lib/systemd/system/systemd-journald.service:12
configures an IP firewall (IPAddressDeny=any), but the local system does not
support BPF/cgroup based firewalling.
[ 5.944229] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning
is only shown for the first loaded unit using IP firewalling.)
[ 6.236246] random: systemd: uninitialized urandom read (16 bytes read)
[ 6.242863] random: systemd: uninitialized urandom read (16 bytes read)
[ 6.246686] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 6.275172] random: systemd: uninitialized urandom read (16 bytes read)
[ 6.276468] systemd[1]: Listening on Journal Socket (/dev/log).
[ 6.306280] systemd[1]: Listening on Journal Audit Socket.
[ 6.335674] systemd[1]: Started Dispatch Password Requests to Console Directory
Watch.
[ 6.367114] systemd[1]: Set up automount Arbitrary Executable File Formats File
System Automount Point.
[ 6.963405] EXT4-fs (mmcblk1p1): re-mounted. Opts: errors=remount-ro
[ 8.016125] systemd-journald[251]: Received request to flush runtime journal
from PID 1
[ 8.538215] audit: type=1400 audit(1550139121.000:2): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=311
comm="apparmor_parser"
[ 8.538248] audit: type=1400 audit(1550139121.000:3): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=311
comm="apparmor_parser"
[ 8.546059] audit: type=1400 audit(1550139121.000:4): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=312
comm="apparmor_parser"
[ 8.546849] audit: type=1400 audit(1550139121.010:5): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="man_filter" pid=312
comm="apparmor_parser"
[ 8.548711] audit: type=1400 audit(1550139121.010:6): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="man_groff" pid=312
comm="apparmor_parser"
[ 8.583947] audit: type=1400 audit(1550139121.040:7): apparmor="STATUS"
operation="profile_load" profile="unconfined"
name="/usr/lib/arm-linux-gnueabihf/lightdm/lightdm-guest-session" pid=310
comm="apparmor_parser"
[ 8.589967] audit: type=1400 audit(1550139121.050:8): apparmor="STATUS"
operation="profile_load" profile="unconfined"
name="/usr/lib/arm-linux-gnueabihf/lightdm/lightdm-guest-session//chromium" pid=310
comm="apparmor_parser"
[ 8.856068] galcore: loading out-of-tree module taints kernel.
[ 8.893991] Galcore version 6.2.4.190076
[ 9.212365] egalax_ts 2-0004: Failed to switch to I2C interface
[ 9.228315] tc358743_mipi 1-000f: no sensor pwdn pin available
[ 9.228387] get_pixelformat: YUV 4:2:2 8-bit (56595559, 1e)
[ 9.228409] tc358743_probe: format: 56595559, capture mode: 0 fps: 60 width: 640
height: 480
[ 9.228871] tc358743_mipi 1-000f: 1-000f supply DGPO not found, using dummy
regulator
[ 9.229218] power_control: 1
[ 9.229228] tc_standby: powerdown=0, power_gp=0xfffffffe
[ 9.335125] Goodix-TS 2-0014: i2c test failed attempt 1: -6
[ 9.365190] tc358743_read_reg:reg=0 ret=-6
[ 9.368023] tc358743_probe:cannot find camera
[ 9.371091] power_control: 0
[ 9.371099] tc_standby: powerdown=1, power_gp=0xfffffffe
[ 9.375166] Goodix-TS 2-0014: i2c test failed attempt 2: -6
[ 9.394758] tc358743_probe: failed, error=-19
[ 9.414681] Goodix-TS 2-0014: I2C communication failure: -6
[ 9.535181] Goodix-TS 2-005d: i2c test failed attempt 1: -6
[ 9.575187] Goodix-TS 2-005d: i2c test failed attempt 2: -6
[ 9.614804] Goodix-TS 2-005d: I2C communication failure: -6
[ 9.620761] adv7180 2-0020: adv7180_get_gpios: pwn-gpios flags(1 -> 0)
[ 9.620833] adv7180 2-0020: adv7180_get_gpios: rst-gpios flags(1 -> 0)
[ 9.644847] adv7180_gpio_state: active=0, rst-gpios(78)=0x1
[ 9.675649] adv7180_probe: cea861=0
[ 9.675737] adv7180_gpio_state: active=0, pwn-gpios(77)=0x1
[ 9.704828] adv7180 2-0020: get mclk failed
[ 9.705271] adv7180 2-0020: adv7180_read:read reg error: reg=11 ret=-6
[ 9.711780] ft5x06-ts 2-0038: reset fffffffe
[ 9.712211] ft5x06-ts 2-0038: Could not detect touch screen -19.
[ 9.718174] ov5640 2-003c: no sensor pwdn pin available
[ 9.722369] ili210x_i2c 2-0041: No platform data!
[ 9.722741] ili210x_i2c 2-0041: i2c transfer failed
[ 9.727013] ili210x_i2c 2-0041: Failed to get firmware version, err: -5
[ 9.732426] ili210x_i2c: probe of 2-0041 failed with error -5
[ 9.745211] tsc2004 2-0048: 2-0048 supply vio not found, using dummy regulator
[ 9.745944] tsc2004 2-0048: tsc2004_cmd: failed, command: 1 i2c error: -6
[ 9.772053] tsc2004 2-0048: Device not present: -6
[ 9.840436] imx-audio-hdmi sound-hdmi: ASoC: CPU DAI soc:hdmi_audio@00120000 not
registered
[ 9.855718] imx-audio-hdmi sound-hdmi: failed to register card: -517
[ 9.925694] ov5640_mipi 1-003e: Failed to update i2c addr to 0x3e (-6)
[ 9.933077] ov5640_mipi 1-003e: ov5640_read_reg(mipi): reg=300a ret=-6
[ 9.938474] ov5640_mipi 1-003e: Camera ov5640_mipi is not found
[ 10.070258] update_device_addr: ov5642 ret=-6
[ 10.094978] ov5642_read_reg:write reg error:reg=300a
[ 10.098687] camera ov5642 is not found(-1) 19
[ 10.254397] mxc_v4l_open: Mxc Camera no sensor ipu0/csi0
[ 10.283916] mxc_v4l_open: Mxc Camera no sensor ipu1/csi0
[ 10.298139] mxc_v4l_open: Mxc Camera no sensor ipu1/csi1
[ 10.353516] mxc_v4l_open: Mxc Camera no sensor ipu0/csi0
[ 10.601659] imx-audio-hdmi sound-hdmi: ASoC: CODEC DAI i2s-hifi not registered
[ 10.601669] imx-audio-hdmi sound-hdmi: failed to register card: -517
[ 10.606405] imx-audio-hdmi sound-hdmi: ASoC: CODEC DAI i2s-hifi not registered
[ 10.606417] imx-audio-hdmi sound-hdmi: failed to register card: -517
[ 10.632541] imx-audio-hdmi sound-hdmi: i2s-hifi <-> soc:hdmi_audio@00120000
mapping ok
[ 12.905293] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 13.015370] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY
driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06,
irq=113)
[ 13.015604] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 13.249981] mxc_sdc_fb fb@2: 1920x1080 h_sync,r,l: 44,88,148 v_sync,l,u: 5,4,36
pixclock=148500000 Hz
[ 13.250113] imx-ipuv3 2800000.ipu: try ipu internal clk
[ 13.274624] imx-ipuv3 2800000.ipu: disp=0, pixel_clk=148500000 148500000
parent=148500000 div=1
[ 14.936256] mxc_sdc_fb fb@2: 1920x1080 h_sync,r,l: 44,88,148 v_sync,l,u: 5,4,36
pixclock=148500000 Hz
[ 14.936546] imx-ipuv3 2800000.ipu: try ipu internal clk
[ 14.964674] imx-ipuv3 2800000.ipu: disp=0, pixel_clk=148500000 148500000
parent=148500000 div=1
[ 15.081976] mxc_sdc_fb fb@2: 1920x1080 h_sync,r,l: 44,88,148 v_sync,l,u: 5,4,36
pixclock=148500000 Hz
[ 15.082095] imx-ipuv3 2800000.ipu: try ipu internal clk
[ 15.104593] imx-ipuv3 2800000.ipu: disp=0, pixel_clk=148500000 148500000
parent=148500000 div=1
[ 15.294654] mxc_sdc_fb fb@2: 1920x1080 h_sync,r,l: 44,88,148 v_sync,l,u: 5,4,36
pixclock=148500000 Hz
[ 15.294775] imx-ipuv3 2800000.ipu: try ipu internal clk
[ 15.324673] imx-ipuv3 2800000.ipu: disp=0, pixel_clk=148500000 148500000
parent=148500000 div=1
[ 18.589363] mxc_sdc_fb fb@2: 1920x1080 h_sync,r,l: 44,88,148 v_sync,l,u: 5,4,36
pixclock=148500000 Hz
[ 18.589497] imx-ipuv3 2800000.ipu: try ipu internal clk
[ 18.614607] imx-ipuv3 2800000.ipu: disp=0, pixel_clk=148500000 148500000
parent=148500000 div=1
[ 228.068178] random: crng init done
[ 228.068196] random: 7 urandom warning(s) missed due to ratelimiting
[ 232.286895] imx-hdmi-audio imx-hdmi-audio: failed to prepare slave dma
[ 292.676935] mxc_v4l_open: Mxc Camera no sensor ipu0/csi0
[ 292.681311] mxc_v4l_open: Mxc Camera no sensor ipu1/csi0
[ 292.685911] mxc_v4l_open: Mxc Camera no sensor ipu1/csi1
[ 292.690786] mxc_v4l_open: Mxc Camera no sensor ipu0/csi0