Three Phase Rectification

3-phase rectification is the process of converting a balanced 3-phase power supply into
a fixed DC supply using solid state diodes or thyristors

We saw in the previous tutorial that the process of converting an AC input

supply into a fixed DC supply is called Rectification with the most popular
circuits used to perform this rectification process is one that is based on solid-
state semiconductor diodes. In fact, rectification of alternating voltages is one
of the most popular applications of diodes, as diodes are inexpensive, small
and robust allowing us to create numerous types of rectifier circuits using
either individually connected diodes or with just a single integrated bridge
rectifier module.
Single phase supplies such as those in houses and offices are generally 120
Vrms or 240 Vrms phase-to-neutral, also called line-to-neutral (L-N), and
nominally of a fixed voltage and frequency producing an alternating voltage or
current in the form of a sinusoidal waveform being given the abbreviation of
“AC”.
Three-phase rectification, also known as poly-phase rectification circuits are
similar to the previous single-phase rectifiers, the difference this time is that
we are using three, single-phase supplies connected together that have been
produced by one single three-phase generator.
The advantage here is that 3-phase rectification circuits can be used to power
many industrial applications such as motor control or battery charging which
require higher power requirements than a single-phase rectifier circuit is able
to supply.
3-phase supplies take this idea one step further by combining together three
AC voltages of identical frequency and amplitude with each AC voltage being
called a “phase”. These three phases are 120 electrical degrees out-of-phase
from each other producing a phase sequence, or phase rotation of:
360o ÷ 3 = 120o as shown.

Three-phase Waveform

The advantage here is that a three-phase alternating current (AC) supply can
be used to provide electrical power directly to balanced loads and rectifiers.
Since a 3-phase supply has a fixed voltage and frequency it can be used by a
rectification circuit to produce a fixed voltage DC power which can then be
filtered resulting in an output DC voltage with less ripple compared to a single-
phase rectifying circuit.

Three-phase Rectification
Having seen that a 3-phase supply is just simply three single-phases
combined together, we can use this multi-phase property to create 3-phase
rectifier circuits.
As with single-phase rectification, three-phase rectification uses diodes,
thyristors, transistors, or converters to create half-wave, full-wave,
uncontrolled and fully-controlled rectifier circuits transforming a given three-
phase supply into a constant DC output level. In most applications a three-
phase rectifier is supplied directly from the mains utility power grid or from a
three-phase transformer if different DC output level is required by the
connected load.
As with the previous single-phase rectifier, the most basic three-phase rectifier
circuit is that of an uncontrolled half-wave rectifier circuit which uses three
semiconductor diodes, one diode per phase as shown.

Half-wave Three-phase Rectification

So how does this three-phase half-wave rectifier circuit work. The anode of
each diode is connected to one phase of the voltage supply with the cathodes
of all three diodes connected together to the same positive point, effectively
creating a diode-“OR” type arrangement. This common point becomes the
positive (+) terminal for the load while the negative (-) terminal of the load is
connected to the neutral (N) of the supply.
Assuming a phase rotation of Red-Yellow-Blue (VA – VB – VC) and the red
phase (VA) starts at 0o. The first diode to conduct will be diode 1 (D1) as it will
have a more positive voltage at its anode than diodes D2 or D3. Thus diode
D1 conducts for the positive half-cycle of VA while D2 and D3 are in their
reverse-biased state. The neutral wire provides a return path for the load
current back to the supply.
120 electrical degrees later, diode 2 (D2) starts to conduct for the positive half-
cycle of VB (yellow phase). Now its anode becomes more positive than diodes
D1 and D3 which are both “OFF” because they are reversed-biased. Similarly,
120o later VC (blue phase) starts to increase turning “ON” diode 3 (D3) as its
anode becomes more positive, thus turning “OFF” diodes D1 and D2.
Then we can see that for three-phase rectification, whichever diode has a
more positive voltage at its anode compared to the other two diodes it will
automatically start to conduct, thereby giving a conduction pattern of:
D1 D2 D3 as shown.

Half-wave Three-phase Rectifier Conduction Waveform

From the above waveforms for a resistive load, we can see that for a half-
wave rectifier each diode passes current for one third of each cycle, with the
output waveform being three times the input frequency of the AC supply.
Therefore there are three voltage peaks in a given cycle, so by increasing the
number of phases from a single-phase to a three-phase supply, the
rectification of the supply is improved, that is the output DC voltage is
smoother.
For a three-phase half-wave rectifier, the supply voltages VA VB and VC are
balanced but with a phase difference of 120o giving:
VA = VP*sin(ωt – 0o)
VB = VP*sin(ωt – 120o)
VC = VP*sin(ωt – 240o)
Thus the average DC value of the output voltage waveform from a 3-phase
half-wave rectifier is given as:
As the voltage supplies peak voltage, VP is equal to VRMS*1.414, it follows that
VP is equal to VP/1.414 giving 0.707*VP, so the average DC output voltage of
the rectifier can be expressed in terms of the rms (root-mean-squared) phase
voltage giving:

3-phase Rectification Example No1

A half-wave 3-phase rectifier is constructed using three individual diodes and
a 120VAC 3-phase star connected transformer. If it is required to power a
connected load with an impedance of 50Ω, Calculate, a) the average DC
voltage output to the load. b) the load current, c) the average current per
diode. Assume ideal diodes.
a). The average DC load voltage:
VDC = 1.17*Vrms = 1.17*120 = 140.4 volts
Note that if we were given the peak voltage (Vp) value, then:
VDC would equal 0.827*Vp or 0.827*169.68 = 140.4V.
b). The DC load current:
IL = VDC/RL = 140.4/50 = 2.81 amperes
c). The average current per diode:
ID = IL/3 = 2.81/3 = 0.94 amperes
One of the disadvantages of half-wave 3-phase rectification is that it requires
a 4-wire supply, that is three phases plus a neutral (N) connection. Also the
average DC output voltage is low at a value represented by 0.827*VP as we
have seen. This is because the output ripple content is three times the input
frequency. But we can improve on these disadvantages by adding three more
diodes to the basic rectifier circuit creating a three-phase full-wave
uncontrolled bridge rectifier.

Full-wave Three-phase Rectification

The full-wave three-phase uncontrolled bridge rectifier circuit uses six diodes,
two per phase in a similar fashion to the single-phase bridge rectifier. A 3-
phase full-wave rectifier is obtained by using two half-wave rectifier circuits.
The advantage here is that the circuit produces a lower ripple output than the
previous half-wave 3-phase rectifier as it has a frequency of six times the
input AC waveform.
Also, the full-wave rectifier can be fed from a balanced 3–phase 3-wire delta
connected supply as no fourth neutral (N) wire is required. Consider the full-
wave 3-phase rectifier circuit below.

Full-wave Three-phase Rectification

As before, assuming a phase rotation of Red-Yellow-Blue (VA – VB – VC) and

the red phase (VA) starts at 0o. Each phase connects between a pair of diodes
as shown. One diode of the conducting pair powers the positive (+) side of
load, while the other diode powers the negative (-) side of load.
Diodes D1 D3 D2 and D4 form a bridge rectifier network between
phases A and B, similarly diodes D3 D5 D4 and D6 between
phases B and C and D5 D1 D6 and D2 between phases C and A.
Thus diodes D1 D3 and D5 feed the positive rail and depending on which one
has a more positive voltage at its anode terminal conducts. Likewise, diodes
D2 D4 and D6 feed the negative rail and whichever diode has a more negative
voltage at its cathode terminal conducts.
Then we can see that for three-phase rectification, the diodes conduct in
matching pairs giving a conduction pattern for the load current of: D1-2 D1-6 D3-
6 D3-6 D3-4 D5-4 D5-2 and D1-2 as shown.

Full-wave Three-phase Rectifier Conduction Waveform

In 3-phase power rectifiers, conduction always occurs in the most positive

diode and the corresponding most negative diode. Thus as the three phases
rotate across the rectifier terminals, conduction is passed from diode to diode.
Then each diode conducts for 120o (one-third) in each supply cycle but as it
takes two diodes to conduct in pairs, each pair of diodes will conduct for only
60o (one-sixth) of a cycle at any one time as shown above.
Therefore we can correctly say that for a 3-phase rectifier being fed by “3”
transformer secondaries, each phase will be separated by 360o/3 thus
requiring 2*3 diodes. Note also that unlike the previous half-wave rectifier,
there is no common connection between the rectifiers input and output
terminals. Therefore it can be fed by a star connected or a delta connected
transformer supply.
So the average DC value of the output voltage waveform from a 3-phase full-
wave rectifier is given as:
Where: VS is equal to (VL(PEAK) ÷ √3) and where VL(PEAK) is the maximum line-to-line
voltage (VL*1.414).

3-phase Rectification Example No2

A 3-phase full-wave bridge rectifier is required to fed a 150Ω resistive load
from a 3-phase 127 volt, 60Hz delta connected supply. Ignoring the voltage
drops across the diodes, calculate: 1. the DC output voltage of the rectifier
and 2. the load current.
1. the DC output voltage:
The RMS (Root Mean Squared) line voltage is 127 volts. Therefore the line-to-
line peak voltage (VL-L(PEAK)) will be:

As the supply is 3-phase, the phase to neutral voltage (VP-N) of any phase will
be:

Note that this is basically the same as saying:

Thus the average DC output voltage from the 3-phase full-wave rectifier is
given as:

Again, we can reduce the maths a bit by correctly saying that for a given line-
to-line RMS voltage value, in our example 127 volts, the average DC output
voltage is:
2. the rectifiers load current.
The output from the rectifier is feeding a 150Ω resistive load. Then using
Ohms law the load current will be:

Uncontrolled 3-phase rectification uses diodes to provide an average output

voltage of a fixed value relative to the value of the input AC voltages. But to
vary the output voltage of the rectifier we need to replace the uncontrolled
diodes, either some or all of them, with thyristors to create what are called
half-controlled or fully-controlled bridge rectifiers.
Thyristors are three terminal semiconductor devices and when a suitable
trigger pulse is applied to the the thyristors gate terminal when its Anode–to-
Cathode terminal voltage is positive, the device will conduct and pass a load
current. So by delaying the timing of the trigger pulse, (firing angle) we can
delay the instant in time at which the thyristor would naturally switch “ON” if it
were a normal diode and the moment it starts to conduct when the trigger
pulse is applied.
Thus with a controlled 3-phase rectification which uses thyristors instead of
diodes, we can control the value of the average DC output voltage by
controlling the firing angle of the thyristor pairs and so the rectified output
voltage becomes a function of the firing angle, α.
Therefore the only difference to the formula used above for the average
output voltage of a 3-phase bridge rectifier is in the cosine angle, cos(α) of the
firing or triggering pulse. So if the firing angle is zero, (cos(0) = 1), the
controlled rectifier performs similar to the previous 3-phase uncontrolled diode
rectifier with the average output voltages being the same.
An example of a fully-controlled 3-phase bridge rectifier is given below:
Fully-controlled 3-phase Bridge Rectifier

Three-phase Rectification Summary

We have seen in this tutorial that three-phase rectification is the process of
converting a 3-phase AC supply into a pulsating DC voltage as rectification
converts the input power supply of a sinusoidal voltage and frequency into a
fixed voltage DC power. Thus power rectification changes an alternating
supply into a unidirectional supply.
But we have also seen that 3-phase half-wave uncontrolled rectifiers, which
use one diode per phase, require a star connected supply as a fourth neutral
(N) wire to close the circuit from load to source. The 3-phase full-wave bridge
rectifier which use two diodes per phase requires just three mains lines,
without neutral, such as that provided by a delta connected supply.
Another advantage of a full-wave bridge rectifier is that the load current is well
balanced across the bridge improving efficiency (the ratio of output DC power
to input power supplied) and reducing the ripple content, both in amplitude
and frequency, as compared to the half-wave configuration.
By increasing the number of phases and diodes within the bridge
configuration it is possible to obtain a higher average DC output voltage with
less ripple amplitude as for example, in 6-phase rectification each diode would
conduct for only one-sixth of a cycle. Also, multi-phase rectifiers produce a
higher ripple frequency means less capacitive filtering and a much smoother
output voltage. Thus 6, 12, 15 and even 24-phase uncontrolled rectifiers can
be designed to improve the ripple factor for various applications.