Printed Pages: 03 Subject Code: KEE101

Paper Id: 120101 Roll No:

BTECH
(SEM I) THEORY EXAMINATION 2018-19
BASIC ELECTRICAL ENGINEERING
Time: 3 Hours Total Marks:100
Note: 1.The question paper contains three sections- A, B & C.
2. Read the instructions carefully in each section
3. Course outcome(CO) has been mentioned against each question.
SECTION-A
1. Attempt ALL: [2x10=20]
a. Define with examples: (i) Active and passive element (ii) bilateral and unilateral
elements. (CO 1)
b. Explain (i) Ideal current source (ii) ideal voltage source. (CO 1)
c. A series circuit has R= 10Ω, L= 0.02H and C= 3µF. Calculate Q-factor of the circuit.
(CO 2)
d. Two ac currents one represented as i1 = 25 sin (314 t + 200) & i2 = 35 sin (314 t +
450). Draw the phasor & show the resultant when they are connected in parallel.
AR

86
(CO 2)

8.
M

22
KU

e. What will happen if the primary of a transformer is connected to dc supply? (CO 3)

9.
f. How can we change the direction of rotation of DC motor? (CO 4)
D

.6
g. Enlist the various methods of starting of single phase induction motor? (CO 4)
O

14
N

h. Why Earth pin is made thicker and bigger than line and neutral? (CO 5)
|1
VI

i. What are the advantages of auto-transformer over two winding transformer? (CO 4)
3
:0

j. Calculate the energy consumption per day in a house using 5 CFLs of 20 W each, 3
03

fans of 60 W each for 3 hrs a day. (CO 5)

:
09

SECTION- B
1 8

2. Attempt any three parts of the following. Each part carries 10 marks. [3x10=30]
20

(a) Find current through 2Ω resistance using superposition theorem in figure 1 (CO1)
-
ec
D
5-
|1

Figure 1

VINOD KUMAR | 15-Dec-2018 09:03:03 | 114.69.228.86

(b) Derive expression of resonance frequency for series RLC circuit. A series circuit
consists of a resistance of 10Ω, and inductance of 50mH and a variable capacitance in series
across a 100V, 50Hz supply. Calculate-
(i) The value of capacitance to produce resonance.
(ii) Voltage across the capacitance.
(iii) Q-factor (CO2)
(c) The maximum efficiency of a 100 KVA, 1100/440 V, 50 Hz transformer is 96%, This
occurs at 75% of full load at 0.8 p.f. lagging. Find the efficiency of transformer at 3.4 FL at
0.6 p.f. leading. (CO3)
(d) A 4-pole shunt generator with lap-connected armature has field and armature resistance of
50Ω and 0.1Ω respectively. If supplying power to 100W lamp load for 100 V. Calculate the
armature current and the generated emf. Consider a contact drop of 1V per brush. (CO4)
(e) Draw the characteristics of battery.
Calculate the backup of battery of 100AH connected to load of 100 watts and supply voltage
is 12V. AR (CO5)

86
SECTION- C

8.
M

3. Attempt any ONE question: [10X1=10]

22
KU

(a)Give the statement of Norton’s Theorem. (CO 1)

9.
D

.6
O

14
Find the current in 12 ohm resistance using Norton’s theorem for the given circuit.
N

|1
VI

3
:0
: 03
09

Figure 2
(b) Determine current through 15 ohm resistance by node analysis. (CO 1)
1 8
- 20
ec
D
5-

Figure 3
|1

4. Attempt any ONE question: [10X1=10]

(a)Derive the expression for resonant frequency & quality factor for an ac circuit under the
condition of parallel resonance. (CO 2)

VINOD KUMAR | 15-Dec-2018 09:03:03 | 114.69.228.86

(b)Derive the relation between line current & phase current in case of three phase delta
connected balanced load. Three identical coils of resistance 8Ω and inductive reactance 6Ω
are connected in delta across 400V mains. Determine power, power factor and line current.
Draw phasor diagram. (CO 2)

5. Attempt any ONE question: [10X1=10]

(a) Discuss the principle of operation of a single phase transformer. Derive EMF equation for
a single phase transformer. (CO 3)

(b) What is voltage Regulation in a single Phase Transformer? What should be its value for
an ideal transformer? (CO 3)

6. Attempt any ONE question: [10X1=10]

(a) Derive the EMF equation of D.C. Generator. An 8 pole lap wound dc generator has 450
armature turns. It operates at 0.02 wb flux per pole and runs at 1000 rpm at no load. Find the
AR

86
emf induced by it. (CO 4)

8.
M

(b)What is the relation between frequencies of stator & rotor currents? A 3-phase, 50Hz

22
KU

induction motor has 6 poles and operates with a slip of 5% at a certain load. Determine

9.
D

.6
(i) The speed of rotor with respect to the stator.
O

(ii) The frequency of the rotor current.

14
N

|1
VI

(iii) The speed of the rotor magnetic field with respect to the stator. (CO 4)
3
:0

7. Attempt any ONE question: [10X1=10]

: 03

(a)Write short notes on the following: (CO 5)

09

(i) MCB (ii) MCCB (c) Fuse (d) Types of wires

1 8

(b) Explain following: (CO 5)

20

(i) Need of Earthing

-
ec

(ii)Battery backup
D
5-
|1

VINOD KUMAR | 15-Dec-2018 09:03:03 | 114.69.228.86

Printed Pages: 03 Subject Code: KEE101
Paper Id: 120101 Roll No:

BTECH
(SEM I) THEORY EXAMINATION 2018-19
BASIC ELECTRICAL ENGINEERING
Time: 3 Hours Total Marks:100
Note: 1.The question paper contains three sections- A, B & C.
2. Read the instructions carefully in each section
3. Course outcome(CO) has been mentioned against each question.
SECTION-A
1. Attempt ALL: [2x10=20]
a. Define with examples: (i) Active and passive element (ii) bilateral and unilateral
elements. (CO 1)
b. Explain (i) Ideal current source (ii) ideal voltage source. (CO 1)
c. A series circuit has R= 10Ω, L= 0.02H and C= 3µF. Calculate Q-factor of the circuit.
(CO 2)
d. Two ac currents one represented as i1 = 25 sin (314 t + 200) & i2 = 35 sin (314 t +
450). Draw the phasor & show the resultant when they are connected in parallel.
AR

86
(CO 2)

8.
M

22
KU

e. What will happen if the primary of a transformer is connected to dc supply? (CO 3)

9.
f. How can we change the direction of rotation of DC motor? (CO 4)
D

.6
g. Enlist the various methods of starting of single phase induction motor? (CO 4)
O

14
N

h. Why Earth pin is made thicker and bigger than line and neutral? (CO 5)
|1
VI

i. What are the advantages of auto-transformer over two winding transformer? (CO 4)
3
:0

j. Calculate the energy consumption per day in a house using 5 CFLs of 20 W each, 3
03

fans of 60 W each for 3 hrs a day. (CO 5)

:
09

SECTION- B
1 8

2. Attempt any three parts of the following. Each part carries 10 marks. [3x10=30]
20

(a) Find current through 2Ω resistance using superposition theorem in figure 1 (CO1)
-
ec
D
5-
|1

Figure 1

VINOD KUMAR | 15-Dec-2018 09:03:03 | 114.69.228.86

(b) Derive expression of resonance frequency for series RLC circuit. A series circuit
consists of a resistance of 10Ω, and inductance of 50mH and a variable capacitance in series
across a 100V, 50Hz supply. Calculate-
(i) The value of capacitance to produce resonance.
(ii) Voltage across the capacitance.
(iii) Q-factor (CO2)
(c) The maximum efficiency of a 100 KVA, 1100/440 V, 50 Hz transformer is 96%, This
occurs at 75% of full load at 0.8 p.f. lagging. Find the efficiency of transformer at 3.4 FL at
0.6 p.f. leading. (CO3)
(d) A 4-pole shunt generator with lap-connected armature has field and armature resistance of
50Ω and 0.1Ω respectively. If supplying power to 100W lamp load for 100 V. Calculate the
armature current and the generated emf. Consider a contact drop of 1V per brush. (CO4)
(e) Draw the characteristics of battery.
Calculate the backup of battery of 100AH connected to load of 100 watts and supply voltage
is 12V. AR (CO5)

86
SECTION- C

8.
M

3. Attempt any ONE question: [10X1=10]

22
KU

(a)Give the statement of Norton’s Theorem. (CO 1)

9.
D

.6
O

14
Find the current in 12 ohm resistance using Norton’s theorem for the given circuit.
N

|1
VI

3
:0
: 03
09

Figure 2
(b) Determine current through 15 ohm resistance by node analysis. (CO 1)
1 8
- 20
ec
D
5-

Figure 3
|1

4. Attempt any ONE question: [10X1=10]

(a)Derive the expression for resonant frequency & quality factor for an ac circuit under the
condition of parallel resonance. (CO 2)

VINOD KUMAR | 15-Dec-2018 09:03:03 | 114.69.228.86

(b)Derive the relation between line current & phase current in case of three phase delta
connected balanced load. Three identical coils of resistance 8Ω and inductive reactance 6Ω
are connected in delta across 400V mains. Determine power, power factor and line current.
Draw phasor diagram. (CO 2)

5. Attempt any ONE question: [10X1=10]

(a) Discuss the principle of operation of a single phase transformer. Derive EMF equation for
a single phase transformer. (CO 3)

(b) What is voltage Regulation in a single Phase Transformer? What should be its value for
an ideal transformer? (CO 3)

6. Attempt any ONE question: [10X1=10]

(a) Derive the EMF equation of D.C. Generator. An 8 pole lap wound dc generator has 450
armature turns. It operates at 0.02 wb flux per pole and runs at 1000 rpm at no load. Find the
AR

86
emf induced by it. (CO 4)

8.
M

(b)What is the relation between frequencies of stator & rotor currents? A 3-phase, 50Hz

22
KU

induction motor has 6 poles and operates with a slip of 5% at a certain load. Determine

9.
D

.6
(i) The speed of rotor with respect to the stator.
O

(ii) The frequency of the rotor current.

14
N

|1
VI

(iii) The speed of the rotor magnetic field with respect to the stator. (CO 4)
3
:0

7. Attempt any ONE question: [10X1=10]

: 03

(a)Write short notes on the following: (CO 5)

09

(i) MCB (ii) MCCB (c) Fuse (d) Types of wires

1 8

(b) Explain following: (CO 5)

20

(i) Need of Earthing

-
ec

(ii)Battery backup
D
5-
|1

VINOD KUMAR | 15-Dec-2018 09:03:03 | 114.69.228.86

 KEE201
Printed Pages: 02 Sub Code:KEE201

Paper Id: 120262 Roll No.

B TECH
(SEM II) THEORY EXAMINATION 2018-19
ELECTRICAL ENGINEERING
Time: 3 Hours Total Marks: 100
Note: 1. Attempt all Sections. If you require any missing data, choose suitably.

SECTION A
1. Attempt all questions in brief. 2 x 10 = 20 CO
a. Define the purpose of Earthing the electrical appliances 5
b. What are the various three phase transformer connections? Name them. 3
c. Explain why transformer cannot be operated on DC. 3
d. What is difference between primary and secondary batteries? 5
e. Define active and passive elements. 1
f. Three resistances each of 20Ω, 30Ω & 50Ω are connected in delta. Calculate 1
corresponding resistances in equivalent star connection.

A
g. What is phase angle difference between the voltage and current phasors in 2

PT
purely capacitive circuits?
h. U
A 3-phase, 440V, induction motor is wound for 4 poles and is supplied from 4
G
50Hz supply system. Calculate the speed of the motor when slip is 5%.

.2
i. Write condition for series resonance. 2
AR

62
j. Write applications of synchronous motor. 4
M

5.
KU

11
SECTION B
2. Attempt any three of the following:
5.
Marks CO
Y

|4
JA

a. Derive the relationship in delta and star connected systems? 10 1

39
VI

b. Derive the expression for the average power in a single phase purely 10 2
8:
R

Resistive circuit. Also draw the phasor diagram and waveform

:5
D

diagram for this circuit.

08

c. An 1100/110V, 22KVA, 1 φ transformer has primary resistance and 10 3

9

reactance 4 Ω and 6 Ω respectively. The secondary resistance

01

and reactance are 0.04 Ω and 0.065 Ω respectively. Calculate

-2

(i) Equivalent resistance and reactance of secondary referred to

ay

primary.
M

(ii) Total resistance & reactance referred to primary.

(iii) Equivalent resistance and reactance of primary referred to
8-

secondary.
|0

(iv) Total copper loss

d. Derive and explain torque-slip Characteristics of 3-phase Induction 10 4
motor.
e. Explain (i) MCB (ii) ELCB (iii) MCCB 10 5

Page 1 of 2
DR VIJAY KUMAR GUPTA | 08-May-2019 08:58:39 | 45.115.62.2
 KEE201
SECTION C
3. Attempt any one part of the following: Marks CO
a. Determine current through 2 Ω resistor using Thevenin theorem. 10 1

b. Determine current through 8 Ω resistor and power in the 4 Ω resistor in 10 1

the Network shown in Fig. Using Superposition theorem.

4. Attempt any one part of the following: Marks CO

a. Why is a single phase induction motor is not self starting. Also explain 10 4

A
the various starting methods.

PT
b. A 250V dc shunt motor takes 41A at full load. Resistances of motor 10 4
armature and shunt field winding are 0.1 Ω and 250 Ω respectively.
U
Find the back emf on full load. What will be generated emf, if working
G

.2
as generator and supplying 41A to a load at terminal voltage of 250V?
AR

62
M

5.
5. Attempt any one part of the following: Marks CO
KU

11
a. Derive half power frequencies, bandwidth and quality factor for series 10 2

5.
resonance occurring in a series R-L-C circuit.
Y

|4
JA

b. A balanced delta connected load of 12+j9 ohm is connected to 3 phase 10 2

39
VI

400 V supply. Find (i) Line current (ii) power factor (iii) power drawn
(iv) reactive volt amp (v) total volt amp
8:
R

:5
D

6. Attempt any one part of the following: Marks CO

08

a. What is an Auto Transformer? What are the advantages and 10 3

9

disadvantages of using an Auto Transformer? Explain (without

01

derivation) how the efficiency varies when a normal two winding

-2

transformer is converted into an Auto Transformer.

ay

b. A transformer is rated at 100kVA. At full load its copper loss is 10 3

1200Watts and iron losses are 960W. Calculate: (i) Efficiency at full
M

load, unity pf (ii) Efficiency at half load, 0.8 pf lagging. (iii)

8-

Efficiency at 75% full load, 0.7 pf lagging (iv) The load KVA at
|0

which maximum efficiency occurs (v) The maximum efficiency at

0.85 pf lagging

7. Attempt any one part of the following: Marks CO

a. Describe electrical characteristics of lead acid battery. 10 5
b. Explain the construction, rating and specific applications of at least two 10 5
types of Wires and Cables used in electrical engineering.

Page 2 of 2
DR VIJAY KUMAR GUPTA | 08-May-2019 08:58:39 | 45.115.62.2
 Printed Pages: 03 Subject Code: KEE101
Paper Id: 120101 Roll No:

BTECH
(SEM I) THEORY EXAMINATION 2018-19
BASIC ELECTRICAL ENGINEERING
Time: 3 Hours Total Marks:100
Note: 1.The question paper contains three sections- A, B & C.
2. Read the instructions carefully in each section
3. Course outcome(CO) has been mentioned against each question.
SECTION-A
1. Attempt ALL: [2x10=20]
a. Define with examples: (i) Active and passive element (ii) bilateral and unilateral
elements. (CO 1)
b. Explain (i) Ideal current source (ii) ideal voltage source. (CO 1)
c. A series circuit has R= 10Ω, L= 0.02H and C= 3µF. Calculate Q-factor of the circuit.
(CO 2)
d. Two ac currents one represented as i1 = 25 sin (314 t + 200) & i2 = 35 sin (314 t +
450). Draw the phasor & show the resultant when they are connected in parallel.
(CO 2)
e. What will happen if the primary of a transformer is connected to dc supply? (CO 3)
f. How can we change the direction of rotation of DC motor? (CO 4)
g. Enlist the various methods of starting of single phase induction motor? (CO 4)
h. Why Earth pin is made thicker and bigger than line and neutral? (CO 5)
i. What are the advantages of auto-transformer over two winding transformer? (CO 4)
j. Calculate the energy consumption per day in a house using 5 CFLs of 20 W each, 3
fans of 60 W each for 3 hrs a day. (CO 5)

SECTION- B
2. Attempt any three parts of the following. Each part carries 10 marks. [3x10=30]
(a) Find current through 2Ω resistance using superposition theorem in figure 1 (CO1)

Figure 1

http:\\www.aktuonline.com
 (b) Derive expression of resonance frequency for series RLC circuit. A series circuit
consists of a resistance of 10Ω, and inductance of 50mH and a variable capacitance in series
across a 100V, 50Hz supply. Calculate-
(i) The value of capacitance to produce resonance.
(ii) Voltage across the capacitance.
(iii) Q-factor (CO2)
(c) The maximum efficiency of a 100 KVA, 1100/440 V, 50 Hz transformer is 96%, This
occurs at 75% of full load at 0.8 p.f. lagging. Find the efficiency of transformer at 3.4 FL at
0.6 p.f. leading. (CO3)
(d) A 4-pole shunt generator with lap-connected armature has field and armature resistance of
50Ω and 0.1Ω respectively. If supplying power to 100W lamp load for 100 V. Calculate the
armature current and the generated emf. Consider a contact drop of 1V per brush. (CO4)
(e) Draw the characteristics of battery.
Calculate the backup of battery of 100AH connected to load of 100 watts and supply voltage
is 12V. (CO5)

SECTION- C
3. Attempt any ONE question: [10X1=10]
(a)Give the statement of Norton’s Theorem. (CO 1)

Find the current in 12 ohm resistance using Norton’s theorem for the given circuit.

Figure 2
(b) Determine current through 15 ohm resistance by node analysis. (CO 1)

Figure 3
4. Attempt any ONE question: [10X1=10]
(a)Derive the expression for resonant frequency & quality factor for an ac circuit under the
condition of parallel resonance. (CO 2)

http:\\www.aktuonline.com
 (b)Derive the relation between line current & phase current in case of three phase delta
connected balanced load. Three identical coils of resistance 8Ω and inductive reactance 6Ω
are connected in delta across 400V mains. Determine power, power factor and line current.
Draw phasor diagram. (CO 2)

5. Attempt any ONE question: [10X1=10]

(a) Discuss the principle of operation of a single phase transformer. Derive EMF equation for
a single phase transformer. (CO 3)

(b) What is voltage Regulation in a single Phase Transformer? What should be its value for
an ideal transformer? (CO 3)

6. Attempt any ONE question: [10X1=10]

(a) Derive the EMF equation of D.C. Generator. An 8 pole lap wound dc generator has 450
armature turns. It operates at 0.02 wb flux per pole and runs at 1000 rpm at no load. Find the
emf induced by it. (CO 4)
(b)What is the relation between frequencies of stator & rotor currents? A 3-phase, 50Hz
induction motor has 6 poles and operates with a slip of 5% at a certain load. Determine
(i) The speed of rotor with respect to the stator.
(ii) The frequency of the rotor current.
(iii) The speed of the rotor magnetic field with respect to the stator. (CO 4)

7. Attempt any ONE question: [10X1=10]

(a)Write short notes on the following: (CO 5)
(i) MCB (ii) MCCB (c) Fuse (d) Types of wires
(b) Explain following: (CO 5)
(i) Need of Earthing
(ii)Battery backup

http:\\www.aktuonline.com
 KEE101 CORRECTION M 15.12.18
Kindly read Q.2. as

Q.2.(c) The maximum efficiency of a 100 KVA, 1100/440 V, 50 Hz transformer is

96%, This occurs at 75% of full load at 0.8 p.f. lagging. Find the efficiency of
transformer at 1/2 Full Load at 0.6 p.f. leading.

Page 1

http:\\www.aktuonline.com
Printed pages: 02 Sub Code: REE101
120102
Paper Id: 120101 Roll No.
B TECH
(SEM I) THEORY EXAMINATION 2018-19
BASIC ELECTRICAL ENGINEERING
Time: 3 Hours Total Marks: 70
Note: 1. Attempt all Sections. If require any missing data; then choose suitably.

SECTION A
1. Attempt all questions in brief. 2 x 7 = 14
a. Explain linear and non linear circuit.
b. Explain ideal voltage and current source with example.
c. Give the advantages and disadvantages of 3-phase system.
d. Explain Quality factor of series resonance circuit.
e. A current wave is represented by the equation i = 20 sin (251t). Calculate the
maximum and RMS value of the current and its frequency.
f. Draw and explain torque slip characteristic of three phase induction motor.
g. What do you mean by magnetic hysteresis?

SECTION B
2. Attempt any three of the following: 7 x 3 = 21
a. Derive the relation for Star to delta conversion.

b. Using superposition theorem find current in 40 ohm resistance.

c. A star connected balanced load is supplied from a three phase balanced supply
with a line voltage of 416 V at a frequency of 50 Hz. Each phase of load
consists of a resistance and a capacitor joined in series and the reading on two
wattmeters connected to measure the total power supplied are 782 watt and
1980 watt, both positive. Calculate (a) the power factor of the circuit (b) the
line current and (c) the capacitance of each capacitor.

d. Give the analogy between magnetic circuit and electric circuit.

e. Explain construction and working principle of three phase synchronous motor.
 SECTION C
3. Attempt any one part of the following: 7x1=7
(a) Find the form factor and Peak factor of the given waveform.

(b) Find current delivered by the voltage source mesh analysis.

4. Attempt any one part of the following: 7x1=7

(a) Derive the relation for cut off frequencies and bandwidth of a series resonance
circuit.
(b) Explain maximum power transfer theorem and find the value of load resistance
and amount of power transferred.

5. Attempt any one part of the following: 7x1=7

(a) Explain construction and working of dynamometer type wattmeter with its
merits and demerits.
(b) What is the necessity of a three phase system? Derive the relation between line
values and phase values of a three phase star and delta connected system.

6. Attempt any one part of the following: 7x1=7

(a) Explain working of a single phase transformer and derive the e.m.f. equation.
Why the rating of transformer is in KVA.
(b) In a 50 KVA, 1100/220 V transformer, the iron and copper losses at full load
are 350 W and 425 W respectively. Calculate the efficiency at (i) full load and
half load unity power factor (ii) full load 0.8 Power factor (iii) maximum
efficiency and load at which maximum efficiency occurs assuming the load to
be resistive.

7. Attempt any one part of the following: 7x1=7

(a) Explain different types of dc motor and give their characteristic.
(b) Explain efficiency of a three phase induction motor and derive the condition for
maximum efficiency.
 Printed Pages: 03 Subject Code: KEE101
Paper Id: 120101 Roll No:

BTECH
(SEM I) THEORY EXAMINATION 2018-19
BASIC ELECTRICAL ENGINEERING
Time: 3 Hours Total Marks:100
Note: 1.The question paper contains three sections- A, B & C.
2. Read the instructions carefully in each section
3. Course outcome(CO) has been mentioned against each question.
SECTION-A
1. Attempt ALL: [2x10=20]
a. Define with examples: (i) Active and passive element (ii) bilateral and unilateral
elements. (CO 1)
b. Explain (i) Ideal current source (ii) ideal voltage source. (CO 1)
c. A series circuit has R= 10Ω, L= 0.02H and C= 3µF. Calculate Q-factor of the circuit.
(CO 2)
d. Two ac currents one represented as i1 = 25 sin (314 t + 200) & i2 = 35 sin (314 t +
450). Draw the phasor & show the resultant when they are connected in parallel.
(CO 2)
e. What will happen if the primary of a transformer is connected to dc supply? (CO 3)
f. How can we change the direction of rotation of DC motor? (CO 4)
g. Enlist the various methods of starting of single phase induction motor? (CO 4)
h. Why Earth pin is made thicker and bigger than line and neutral? (CO 5)
i. What are the advantages of auto-transformer over two winding transformer? (CO 4)
j. Calculate the energy consumption per day in a house using 5 CFLs of 20 W each, 3
fans of 60 W each for 3 hrs a day. (CO 5)

SECTION- B
2. Attempt any three parts of the following. Each part carries 10 marks. [3x10=30]
(a) Find current through 2Ω resistance using superposition theorem in figure 1 (CO1)

Figure 1

http:\\www.aktuonline.com
 (b) Derive expression of resonance frequency for series RLC circuit. A series circuit
consists of a resistance of 10Ω, and inductance of 50mH and a variable capacitance in series
across a 100V, 50Hz supply. Calculate-
(i) The value of capacitance to produce resonance.
(ii) Voltage across the capacitance.
(iii) Q-factor (CO2)
(c) The maximum efficiency of a 100 KVA, 1100/440 V, 50 Hz transformer is 96%, This
occurs at 75% of full load at 0.8 p.f. lagging. Find the efficiency of transformer at 3.4 FL at
0.6 p.f. leading. (CO3)
(d) A 4-pole shunt generator with lap-connected armature has field and armature resistance of
50Ω and 0.1Ω respectively. If supplying power to 100W lamp load for 100 V. Calculate the
armature current and the generated emf. Consider a contact drop of 1V per brush. (CO4)
(e) Draw the characteristics of battery.
Calculate the backup of battery of 100AH connected to load of 100 watts and supply voltage
is 12V. (CO5)

SECTION- C
3. Attempt any ONE question: [10X1=10]
(a)Give the statement of Norton’s Theorem. (CO 1)

Find the current in 12 ohm resistance using Norton’s theorem for the given circuit.

Figure 2
(b) Determine current through 15 ohm resistance by node analysis. (CO 1)

Figure 3
4. Attempt any ONE question: [10X1=10]
(a)Derive the expression for resonant frequency & quality factor for an ac circuit under the
condition of parallel resonance. (CO 2)

http:\\www.aktuonline.com
 (b)Derive the relation between line current & phase current in case of three phase delta
connected balanced load. Three identical coils of resistance 8Ω and inductive reactance 6Ω
are connected in delta across 400V mains. Determine power, power factor and line current.
Draw phasor diagram. (CO 2)

5. Attempt any ONE question: [10X1=10]

(a) Discuss the principle of operation of a single phase transformer. Derive EMF equation for
a single phase transformer. (CO 3)

(b) What is voltage Regulation in a single Phase Transformer? What should be its value for
an ideal transformer? (CO 3)

6. Attempt any ONE question: [10X1=10]

(a) Derive the EMF equation of D.C. Generator. An 8 pole lap wound dc generator has 450
armature turns. It operates at 0.02 wb flux per pole and runs at 1000 rpm at no load. Find the
emf induced by it. (CO 4)
(b)What is the relation between frequencies of stator & rotor currents? A 3-phase, 50Hz
induction motor has 6 poles and operates with a slip of 5% at a certain load. Determine
(i) The speed of rotor with respect to the stator.
(ii) The frequency of the rotor current.
(iii) The speed of the rotor magnetic field with respect to the stator. (CO 4)

7. Attempt any ONE question: [10X1=10]

(a)Write short notes on the following: (CO 5)
(i) MCB (ii) MCCB (c) Fuse (d) Types of wires
(b) Explain following: (CO 5)
(i) Need of Earthing
(ii)Battery backup

http:\\www.aktuonline.com
 KEE101 CORRECTION M 15.12.18
Kindly read Q.2. as

Q.2.(c) The maximum efficiency of a 100 KVA, 1100/440 V, 50 Hz transformer is

96%, This occurs at 75% of full load at 0.8 p.f. lagging. Find the efficiency of
transformer at 1/2 Full Load at 0.6 p.f. leading.

Page 1

http:\\www.aktuonline.com
 Printed pages: 02 Sub Code: NEE101
120105
Paper Id: 120101 Roll No.

B TECH
(SEM I) THEORY EXAMINATION 2018-19
BASIC ELECTRICAL ENGINEERING
Time: 3 Hours Total Marks: 100
Note: 1. Attempt all Sections. If require any missing data; then choose suitably.

SECTION A
1. Attempt all questions in brief. 2 x 10 = 20
a. What do you mean by unilateral and bilateral elements?
b. Can we apply KVL in a loop containing a current source? Give answer with
reason.
c. What do you mean by average value of an alternating quantity?
d. Calculate the R.M.S. value of a half wave rectified current.
e. Explain phase sequence in a three phase circuit.
f. Explain eddy current damping in the measuring instruments.
g. What is the necessity of earthling?
h. Explain losses in magnetic circuit.
i. Explain the principle of Electromechanical energy conversion.
j. What is the role of commutator in dc machine?

SECTION B
2. Attempt any three of the following: 10 x 3 = 30
a. Using nodal analysis find current I in the circuit given below.

b. A capacitor of 35 µF is connected in series with a variable resistor. The circuit

is connected across a 50 Hz main. Find the value of the resistor for a particular
condition when the voltage across the capacitor is half the supply voltage.

c. Explain two wattmeter methods for the measurement of three phase power.
Derive the relation for three phase power with the help of phasor diagram.

d. Draw and explain equivalent circuit of a single phase transformer.

e. A short shunt compound generator supplies 200 A at 100 V. The resistance of
armature, series field and shunt field is respectively 0.04, 0.03 and 60 ohm.
Find the emf generated.

http:\\www.aktuonline.com
 SECTION C
3. Attempt any one part of the following: 10 x 1 = 10
(a) Find the equivalent resistance between point A and B using star delta
conversion

(b) Determine power loss in the 1 ohm resistance across terminal A and B of
circuit given in figure using Norton’s theorem.

4. Attempt any one part of the following: 10 x 1 = 10

(a) Explain power factor. What are the causes of low power factor? Explain
methods of power factor improvement.
(b) Find the capacitance which must be connected in series with a 100W, 110V
lamp in order that the lamp may draw its normal current when the combination
is connected to a 230V, 50 Hz supply.
5. Attempt any one part of the following: 10 x 1 = 10
(a) Three inductive coils, each with a resistance of 15 ohm and an inductance of
0.03 H are connected (i) in star (ii) in delta, to 3 phase, 400V 50 Hz supply.
Calculate for each of the above case (i) Phase current and line current (ii) total
power absorbed.
(b) Explain construction and working of PMMC type instruments also gives it’s
and disadvantages.
6. Attempt any one part of the following: 10 x 1 = 10
(a) What do mean by earthling? Explain any methods of earthling.
(b) An electromagnet is shown in figure whose area of cross section is 12cm 2.
Mean length of iron path is 50cm. It is excited by two coils each having 400
turns. When the current in the coil is 1.0 A, the resulting flux density gives a
relative permeability of 1300. Calculate (i) reluctance of iron part, air gap and
total reluctance.(ii) total flux(iii) flux density in air gap.

7. Attempt any one part of the following: 10 x 1 = 10

(a) Explain double field revolving theory for single phase induction motor.
(b) An 8 pole alternator runs at 750 rpm. It supplies power to a 6 pole, 3 phase
induction motor, which has a full load slip of 3 %. Find the full load speed of
the induction motor and the frequency of its rotor emf.

http:\\www.aktuonline.com
Printed pages: 02 Sub Code: REE101
120102
Paper Id: 120101 Roll No.
B TECH
(SEM I) THEORY EXAMINATION 2018-19
BASIC ELECTRICAL ENGINEERING
Time: 3 Hours Total Marks: 70
Note: 1. Attempt all Sections. If require any missing data; then choose suitably.

SECTION A
1. Attempt all questions in brief. 2 x 7 = 14
a. Explain linear and non linear circuit.
b. Explain ideal voltage and current source with example.
c. Give the advantages and disadvantages of 3-phase system.
d. Explain Quality factor of series resonance circuit.
e. A current wave is represented by the equation i = 20 sin (251t). Calculate the
maximum and RMS value of the current and its frequency.
f. Draw and explain torque slip characteristic of three phase induction motor.
g. What do you mean by magnetic hysteresis?

SECTION B
2. Attempt any three of the following: 7 x 3 = 21
a. Derive the relation for Star to delta conversion.

b. Using superposition theorem find current in 40 ohm resistance.

c. A star connected balanced load is supplied from a three phase balanced supply
with a line voltage of 416 V at a frequency of 50 Hz. Each phase of load
consists of a resistance and a capacitor joined in series and the reading on two
wattmeters connected to measure the total power supplied are 782 watt and
1980 watt, both positive. Calculate (a) the power factor of the circuit (b) the
line current and (c) the capacitance of each capacitor.

d. Give the analogy between magnetic circuit and electric circuit.

e. Explain construction and working principle of three phase synchronous motor.
 SECTION C
3. Attempt any one part of the following: 7x1=7
(a) Find the form factor and Peak factor of the given waveform.

(b) Find current delivered by the voltage source mesh analysis.

4. Attempt any one part of the following: 7x1=7

(a) Derive the relation for cut off frequencies and bandwidth of a series resonance
circuit.
(b) Explain maximum power transfer theorem and find the value of load resistance
and amount of power transferred.

5. Attempt any one part of the following: 7x1=7

(a) Explain construction and working of dynamometer type wattmeter with its
merits and demerits.
(b) What is the necessity of a three phase system? Derive the relation between line
values and phase values of a three phase star and delta connected system.

6. Attempt any one part of the following: 7x1=7

(a) Explain working of a single phase transformer and derive the e.m.f. equation.
Why the rating of transformer is in KVA.
(b) In a 50 KVA, 1100/220 V transformer, the iron and copper losses at full load
are 350 W and 425 W respectively. Calculate the efficiency at (i) full load and
half load unity power factor (ii) full load 0.8 Power factor (iii) maximum
efficiency and load at which maximum efficiency occurs assuming the load to
be resistive.

7. Attempt any one part of the following: 7x1=7

(a) Explain different types of dc motor and give their characteristic.
(b) Explain efficiency of a three phase induction motor and derive the condition for
maximum efficiency.
Scanned by CamScanner
 Printed Page 1 of 2 Sub Code:KEE101
Paper Id: 120101 Roll No: 0 0 0 0 0 0 0 0 0 0 0 0 0

B TECH
(SEM-I) THEORY EXAMINATION 2019-20
BASIC ELECTRICAL ENGG.
Time: 3 Hours Total Marks: 100
Note: 1. Attempt all Sections. If require any missing data; then choose suitably.

SECTION A

1. Attempt all questions in brief. 2 x 10 = 20

Qno. Question Marks C
O
a. What do you understand by unilateral and bilateral elements? Give examples. 2 1
b. What is the utility of superposition theorem? 2 1
c. Determine the form factor of AC current i= 200 Sin (157 t + π/6). 2 2
d. Explain the term “Dynamic Impedence” in AC circuits 2 2
e. How MMF is related to Reluctance. Explain 2 3
f. Define voltage regulation of a transformer. 2 3
g. Why commutator is needed? 2 4
h. Give the expression of speed in terms of poles and frequency of supply. 2 4
i. Write full form of (i) MCB (ii) MCCB (iii) ELCB (iv) SFU. 2 5
j. What are the factors that affect the battery capacity? 2 5
www.aktuonline.com

SECTION B

2. Attempt any three of the following: 10 x 3 = 30

Qno. Question Marks C
O
a. Determine the current flowing through 5 ohms resistance in the network shown 10 1
below (fig-1) using Thevenin’s theorem.

Fig (1)
b. The instantaneous values of two alternating voltages are represented by V1 = 60 10 2
Sin θ and V2 = Sin (θ- π/3). Derive expressions for the instantaneous values of
(i) the sum and (ii) the difference of these voltages.
c. Explain different types of Magnetic materials with examples. 10 3
d. Derive the expression of torque for dc motor. Also discuss the applications of 10 4
it.
e. An alkaline cell is discharged at a steady current of 4 A for 12 hours, the 10 5
average terminal voltage being 1.2 V. To restore it to original state of voltage, a
steady current of 3 A for 20 hours is required, the average terminal voltage
being 1.44 V. Calculate the ampere-hour and watt-hour efficiencies in this
particular case.

1|P a ge
http://www.aktuonline.com
 Printed Page 2 of 2 Sub Code:KEE101
Paper Id: 120101 Roll No: 0 0 0 0 0 0 0 0 0 0 0 0 0

SECTION C
3. Attempt any one part of the following: 10 x 1 = 10
Qno. Question Marks CO
a. Using superposition, find the current flowing through 2 ohm resistance in 10 1
following circuit (fig-2).

Fig (2)

b. Derive an expression of delta to star and star to delta transformation with 10 1

example and satisfy the condition of both expressions.
4. Attempt any one part of the following: 10 x 1 = 10
Qno. Question Marks CO

a. Derive an expression of resonance frequency in series resonance circuit. 10 2

If the bandwidth of a resonant circuit is 10 KHz and the lower half
power frequency is 120 KHz, find out the value of the upper half power
frequency and the quality factor of the circuit.
b. Derive the relationship between line and phase current & voltage for a 10 2
star connected 3-phase balanced system.
A balanced delta connected load of (12 + j 9) Ω/ phase is connected to 3-
www.aktuonline.com

phase 400 V supply. Calculate line current, power factor and power
drawn by it.
5. Attempt any one part of the following: 10 x 1 = 10
Qno. Question Marks CO
a. Draw and explain the no load and full load phasor diagrams for a 10 3
single phase transformer.

b. (i) Explain single phase Auto transformer and give its application. 10 3
(ii) In a 25 KVA, 2000/200 V transformer, the constant and variable
losses are 350 W and 400 W respectively. Calculate the efficiency on
unity power factor at (i) full load and (ii) half load.
6. Attempt any one part of the following: 10 x 1 = 10
Qno. Question Marks CO
a. Draw the slip-torque characteristics of three phase induction motor. 10 4
A 3-phase, 50 Hz induction motor has 6 poles and operates with a slip of 5 % at
a certain load. Determine (i) the speed of the rotor with respect to the stator (ii)
the frequency of rotor current (iii) the speed of the rotor magnetic field with
respect to rotor.
b. (i) Describe any one method of starting single phase induction motor 10 4
with neat diagram.
(ii) Why Synchronous motor is not self starting?
7. Attempt any one part of the following: 10 x 1 = 10
Qno. Question Marks CO
a. Explain the requirement of earthing for electrical equipment. What is the 10 5
difference between neutral and earthing
b. Name the various cables used in electrical system based on insulation. Explain 10 5
any two. What are the features of good conductor in electrical circuit

2|P a ge
http://www.aktuonline.com
 i
ha
ad
iP
or
Po

www.pooripadhai.com
 i
ha
ad
iP
or
Po

www.pooripadhai.com
 Printed Page: 1 of 3
Subject Code: KEE101
0Roll No: 0 0 0 0 0 0 0 0 0 0 0 0 0

BTECH
(SEM I) THEORY EXAMINATION 2021-22
BASIC ELECTRICAL ENGG
Time: 3 Hours Total Marks: 100
Notes:
 Attempt all Sections and Assume any missing data.
 Appropriate marks are allotted to each question, answer accordingly.

SECTION-A Attempt All of the following Questions in brief Marks (10X2=20) CO

Q1(a) Define the expression for form factor and peak factor
Q1(b) State Kirchoff’s law.
Q1(c) Define electromotive force
Q1(d) Define power factor
Q1(e) Write the statement of superposition theorem
Q1(f) What is the function of commutator in DC generator
Q1(g) What is KVA rating of a transformer
Q1(h) Draw the no load phasor diagram of a transformer
Q1(i) Define a slip of an induction motor
Q1(j) What is called synchronous speed in AC machines

9
SECTION-B Attempt ANY THREE of the following Questions Marks (3X10=30) CO

17
3
Q2(a) (i) Derive the emf equation of a transformer
19

(ii) Derive the condition for maximum efficiency in single phase transformer

1.
2_

Q2(b) i) List all the important parts of a D.C. Motor and explain the importance of each..

24
ii) Calculate the emf generated by 4 pole wave wound generator having 65 slots
2P

5.
with 12 conductors per slot when driven at 1200 rpm. The flux per pole is 0.02 wb.

.5
P2

Q2(c) Using Thevenin theorem, find current in 1 Ω resistor in the circuit shown in figure
17
below:
Q

|1
6
:1
: 18
09
2
02

Q2(d) Use nodal analysis to find the voltage across and current through 4 Ω resistor
-2

in Figure given below:

ar
M
5-
|2

Q2(e) Use superposition theorem to find current I in the circuit shown in Figure below.
All resistances are in ohms.

QP22P2_193 | 25-Mar-2022 09:18:16 | 117.55.241.179

 Printed Page: 2 of 3
Subject Code: KEE101
0Roll No: 0 0 0 0 0 0 0 0 0 0 0 0 0

BTECH
(SEM I) THEORY EXAMINATION 2021-22
BASIC ELECTRICAL ENGG

SECTION-C Attempt ANY ONE following Question Marks (1X10=10) CO

Q3(a) Reduce the network of Fig. 1 to obtain the equivalent resistance as seen between
nodes ad.

9
17
3
19

1.
2_

24
Q3(b) With the help of Norton’s theorem, find V0 in the circuit shown below. All
2P

resistances are in Ohms.

5.
.5
P2

17
Q

|1
6
:1
: 18
09
2

SECTION-C Attempt ANY ONE following Question Marks (1X10=10) CO

02

Q4(a) A series R – L – C circuit consists of R = 1000 Ohm, L = 100 mH and C = 10 µF.

The applied voltage across the circuit is 100 V.
-2

(i) Find the resonant frequency of the circuit.

ar

(ii) Find the quality factor of the circuit at the resonant frequency.
M

(iii) At what angular frequencies do the half power points occur?

5-

(iv) Calculate the bandwidth of the circuit.

|2

Q4(b) Three impedances of (70.7 + j 70.7) Ohm, (120 + j 160) Ohm and (120 + j 90) Ohm
are connected in parallel across a 250 V supply. Determine (i) admittance of the
circuit (ii) supply current and (iii) circuit power factor.
SECTION-C Attempt ANY ONE following Question Marks (1X10=10) CO
Q5(a) A transformer on no-load has a core loss of 50W, draws a current of 2A and has an
induced emf of 230V. Determine the no-load power factor, core loss current and
magnetizing current. Also, calculate the no-load circuit parameters of the
transformer. Neglect winding resistance and leakage flux.
Q5(b) Explain the performance of principal of operation of single phase transformer.

QP22P2_193 | 25-Mar-2022 09:18:16 | 117.55.241.179

 Printed Page: 3 of 3
Subject Code: KEE101
0Roll No: 0 0 0 0 0 0 0 0 0 0 0 0 0

BTECH
(SEM I) THEORY EXAMINATION 2021-22
BASIC ELECTRICAL ENGG

SECTION-C Attempt ANY ONE following Question Marks (1X10=10) CO

Q6(a) A 4-pole generator with 400 armature conductors has a useful flux of 0.04Wb per
pole. What is the
emf produced if the machine is wave wound and runs at 1200rpm? What must be the
speed at which the machine should be driven to generate the same emf if machine is
lap wound?
Q6(b) An 8-pole, 400V shunt motor has 960 wave connected armature conductors. The full
load armature current is 40A and flux per pole is 0.02Wb. The armature resistance is
0.1Ω and the contact drop is 1V per brush. Calculate the full load speed of the
motor.
SECTION-C Attempt ANY ONE following Question Marks (1X10=10) CO
Q7(a) (i) Explain the slip torque characteristics of the three-phase induction motor
(ii) The voltage applied to the stator of a three phase, 4 pole induction motor has
frequency of 50 Hz. Th frequency of the emf induced in the rotor is 15.5 Hz.
Determine the slip and speed at which motor is running.

9
Q7(b) (i) Write short notes on MCB and MCCB

17
3
19

(ii) Write short notes on characteristics of batteries.

1.
2_

24
2P

5.
.5
P2

17
Q

|1
6
:1
: 18
09
2
02
-2
ar
M
5-
|2

QP22P2_193 | 25-Mar-2022 09:18:16 | 117.55.241.179

 Printed Page: 1 of 3
Subject Code: KEE101T
0Roll No: 0 0 0 0 0 0 0 0 0 0 0 0 0

BTECH
(SEM I) THEORY EXAMINATION 2021-22
BASIC ELECTRICAL ENGINEERING

Time: 3 Hours Total Marks: 100

Notes:
 Attempt all Sections and Assume any missing data.
 Appropriate marks are allotted to each question, answer accordingly.

SECTION-A Attempt All of the following Questions in brief Marks (10X2=20)

Q1(a) What is use of form factor and peak factor?
Q1(b) What is the ratio of no-load speed to full load speed of a 200 kVA, 12 poles, 2200 V, 3 phase,
60 Hz synchronous motor?
Q1(c) Write Difference between EMF and Potential Difference
Q1(d) Define power factor
Q1(e) Is the superposition theorem valid for direct calculation of power? Explain briefly.
Q1(f) What is the need of commutator in DC generator?
Q1(g) Why is Transformer Ratings done in Volt Amperes (VA).
Q1(h) Draw the no load phasor diagram of a transformer
Q1(i) For heavy loads,What is the relation between torque (T) and slip (S) in induction motor.
Q1(j) What is the difference between asynchronous motor and synchronous motor?

9
17
3
19

SECTION-B Attempt ANY THREE of the following Questions Marks (3X10=30)

1.
Q2(a) (i) Derive the emf equation of a transformer
2_

24
(ii) Derive the condition for maximum efficiency in single phase transformer
2P

5.
Q2(b) i) List all the important parts of a D.C. Motor and explain the importance of each..

.5
P2

ii) Calculate the emf generated by 4 pole wave wound generator having 65 slots with 12
17
conductors per slot when driven at 1200 rpm. The flux per pole is 0.02 wb.
Q

Q2(c) Using Thevenin theorem, find current in 1 Ω resistor in the circuit shown in figure below:
|1
3
:3
: 53
08
2
02

Q2(d) Use nodal analysis to find the voltage across and current through 4 Ω resistor
-2

in Figure given below:

ar
M
5-
|2

Q2(e) Use superposition theorem to find current I in the circuit shown in Figure below. All resistance
are in ohms.

QP22P2_193 | 25-Mar-2022 08:53:33 | 117.55.241.179

 Printed Page: 2 of 3
Subject Code: KEE101T
0Roll No: 0 0 0 0 0 0 0 0 0 0 0 0 0

BTECH
(SEM I) THEORY EXAMINATION 2021-22
BASIC ELECTRICAL ENGINEERING

SECTION-C Attempt ANY ONE following Question Marks (1X10=10)

Q3(a) Reduce the network of Fig. 1 to obtain the equivalent resistance as seen between nodes ad.

9
17
3
19

1.
2_

24
Q3(b) With the help of Norton’s theorem, find V0 in the circuit shown below. All resistances are in
2P

Ohms.

5.
.5
P2

17
Q

|1
3
:3
: 53
08

SECTION-C Attempt ANY ONE following Question Marks (1X10=10)

2
02

Q4(a) A series R – L – C circuit consists of R = 1000 Ohm, L = 100 mH and C = 10 µF.

The applied voltage across the circuit is 100 V.
-2

(i) Find the resonant frequency of the circuit.

ar

(ii) Find the quality factor of the circuit at the resonant frequency.
M

(iii) At what angular frequencies do the half power points occur?

5-

(iv) Calculate the bandwidth of the circuit.

|2

Q4(b) Three impedances of (70.7 + j 70.7) Ohm, (120 + j 160) Ohm and (120 + j 90) Ohm
are connected in parallel across a 250 V supply. Determine (i) admittance of the circuit (ii)
supply current and (iii) circuit power factor.
SECTION-C Attempt ANY ONE following Question Marks (1X10=10)
Q5(a) A transformer on no-load has a core loss of 50W, draws a current of 2A and has an induced
emf of 230V. Determine the no-load power factor, core loss current and magnetizing current.
Also, calculate the no-load circuit parameters of the transformer. Neglect winding resistance
and leakage flux.
Q5(b) Explain the performance of principal of operation of single phase transformer.

QP22P2_193 | 25-Mar-2022 08:53:33 | 117.55.241.179

 Printed Page: 3 of 3
Subject Code: KEE101T
0Roll No: 0 0 0 0 0 0 0 0 0 0 0 0 0

BTECH
(SEM I) THEORY EXAMINATION 2021-22
BASIC ELECTRICAL ENGINEERING

SECTION-C Attempt ANY ONE following Question Marks (1X10=10)

Q6(a) A 4-pole generator with 400 armature conductors has a useful flux of 0.04Wb per pole. What
is the
emf produced if the machine is wave wound and runs at 1200rpm? What must be the speed
at which the machine should be driven to generate the same emf if machine is lap wound?
Q6(b) An 8-pole, 400V shunt motor has 960 wave connected armature conductors. The full load
armature current is 40A and flux per pole is 0.02Wb. The armature resistance is 0.1Ω and the
contact drop is 1V per brush. Calculate the full load speed of the motor.
SECTION-C Attempt ANY ONE following Question Marks (1X10=10)
Q7(a) (i) Explain the slip torque characteristics of the three-phase induction motor
(ii) The voltage applied to the stator of a three phase, 4 pole induction motor has frequency of
50 Hz. Th frequency of the emf induced in the rotor is 15.5 Hz. Determine the slip and speed
at which motor is running.
Q7(b) (i) Write short notes on MCB and MCCB
(ii) Write short notes on characteristics of batteries.

9
17
3
19

1.
2_

24
2P

5.
.5
P2

17
Q

|1
3
:3
: 53
08
2
02
-2
ar
M
5-
|2

QP22P2_193 | 25-Mar-2022 08:53:33 | 117.55.241.179