Powerflex Drives With Totalforce Control Conditions Reference Data

750-RD102C-EN-P
PowerFlex Drives with TotalFORCE Control Conditions Reference Data
This publication lists the conditions for PowerFlex® Drives with TotalFORCE® Control
About This For more information see: PowerFlex Drives with TotalFORCE Control Programming Manual (firmware revision 10.xxx…13.002)
Publication
750-PM101
Important: Rockwell Automation is not responsible for any content or format changes made by other parties after downloading this spreadsheet file. The original file can be re-downloaded at any time.
TIP: When you search for information in a spreadsheet, set the search options to search the workbook, rather than the current sheet (tab).
Your comments help us serve your documentation needs better. If you have any suggestions on how to improve our content, complete the form at: rok.auto/docfeedback
Allen-Bradley, expanding human possibility, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
EtherNet/IP is a trademark of ODVA, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Rockwell Automation recognizes that some of the terms that are currently used in our industry, in this publication, and in product help files are not in alignment with the movement toward inclusive language in technology. We are
proactively collaborating with industry peers to find alternatives to such terms and making changes to our products and content. Please excuse the use of such terms in our content while we implement these changes.
Publication 750-RD102C-EN-P - March 2024 Copyright © 2024 Rockwell Automation Inc. All Rights Reserved. Printed in USA.
Supersedes Publication 750-RD102B-EN-P - May 2023
Summary of Changes
Date
Mar-23
Mar-23
Mar-23
Mar-23
Mar-23
Mar-23
Mar-23
Mar-23
mmary of Changes
Changes
Port 0 Tab
6 ‘SecureEraseCplt’: New resettable fault
88 ‘Safety Jmpr Out’: Update condition type and action description
89 ‘Safety Jumper In’: Update condition type and action description
177 ‘NonStdDataSource’: New configurable condition
308 ‘New System’: Update description
318 ‘Unknown Device’: Update description
347 ‘VelUnit Mismatch’: New alarm
348 ‘Vltg Class Cfg’: New alarm
349 ‘DutyRatingMismth’: New alarm
Port 9 Tab
9012 ‘TP MtrCtrl Mode’: Update description
9013 ‘Torq Prove Cflct’: Update description
9014 ‘TP Encls Config’: Update description
9015 ‘TP Sec Mtr Ctrl’: Update description
9048 ‘Sleep Config’: Update description
Port 10-11 Tab

10003 ‘Motor Overload’: Update action description
10040 ‘Ext Prechrg Err’: Update description
10055 ‘Travel Lim Cflct’: Update description
10059 ‘Invld Homing Cfg’: Update description
10069 ‘SyRSpdEstErr’: New fault
10072 ‘PM Offset Cnflct’: Corrected bit number in description
10076 ‘Excess Psn Err’: Update fault and action descriptions
10085 ‘IPM OverCurrent’: Update action description
10092 ‘SW OverCurrent’: Update action description
10113 ‘SlipInvalidRange’: New alarm
10122 ‘SyR OpenLoop PWM’: New alarm
10132 ‘InvldAutnTestCfg’: New alarm
Port 12 Tab
12024 ‘TAM Cal Missing’: New alarm
12026 ‘Ground Flt’: Update action description
12084 ‘Bus Imbalanc Flt’: Update action description
12087 ‘BusCond BayOTmp’: Update fault and action descriptions
12136 ‘Mtrside IOC Flt’: Update action description
12137 ‘Pwr Struc Fault’: Update action description
Port 13 Tab
13078 ‘Frame 5 Actv Dmp’: New alarm
Port 14 Tab
14084 ‘Bus Imbalanc Flt’: Update action description
14087 ‘BusCond BayOTmp’: Update fault and action descriptions
14117 ‘CapHighResonance’: Correct display text, update fault and action descriptions
14118 ‘CapOverResonance’: Correct display text, update fault and action descriptions
14135 ‘BusCapVltgImbal’: New alarm
Options Tab
nn008 ‘Drive Misconfig’: Update fault and action descriptions
Syslog Tab
New CIP Security tab added.
Code Name
1 Auxiliary Input
2 Sys Default Fail
3 Emerg OVRD Actv
4 Energy Pause Cfg
6 SecureEraseCplt
7 EmergOVRD Actv
8 EmergOVRD Deactv
9 Firmware Started
10 Firmware Stopped
15 AuRsts Exhausted
16 CPU OverTemp Alm
17 CPU OverTemp Flt
18 System Defaulted
21 Clr Fault Queue
22 Clr Alarm Queue
23 Board OT Fault
24 Board OT Alarm
25 Board UT Fault
26 Board UT Alarm
27 Module Defaulted
29 Port 1 Adapter
30 Port 2 Adapter
31 Port 3 Adapter
32 Port 4 Adapter
33 Port 5 Adapter
34 Port 6 Adapter
35 Port 1 DPI Loss
36 Port 2 DPI Loss
37 Port 3 DPI Loss
38 Port 4 DPI Loss
39 Port 5 DPI Loss
40 Port 6 DPI Loss
43 PwrDn NVS Blank
58 PwrDn Data Chksm
60 New Firmware
61 Invalid RTC Time
62 RTC HW Failed
63 Time Change
64 Pwr Cyc Cnt Ovf
65 Time Chg Cnt Ovf
66 PwrDn Backup
67 PwrDn Data Fail
68 PwrDn Sig Fail
69 Cond Data Lost
70 Firmware Update
71 Bipolar Conflict
72 Digin Regen Fail
73 DigIn Cfg B
74 DigIn Cfg C
77 Drive Reset
78 Pod Fan Alarm
80 Drive Faulted
82 Clr Event Queue
83 Clr Excptn Queue
84 MixedCorrProt
86 HW Enbl Jmpr Out
87 Safety Brd Fault
88 Safety Jmpr Out
89 Safety Jumper In
92 SafetyHealth Err
93 SafetyPwrOn Err
94 SafetyPwrOff Err
95 FS Enbl Ch Error
104 Port 4 Cfg
105 Port 5 Cfg
106 Port 6 Cfg
107 Port 7 Cfg
108 Port 8 Cfg
112 Port 12 Cfg
114 Port 14 Cfg
128 LC Incomp PFB
129 Prev Maint Reset
131 In Fan Life
132 Pod Fan Life
133 Pwr Rf Fan Life
134 Wrg Bay Fan Life
135 CtrlBay Fan Life
171 No Stop Source
174 TAM Det Not Cfg
175 TAM Cfg Not Det
176 InvldDataSource
177 NonStdDataSource
180 Invld 2Wire Cfg
300 Nvs Lost Config
301 Pfile Create Err
302 Pfile Login Err
303 HSI Offline
304 AFE PreChrg Fail
305 No Sfib Detected
306 HW Not Compatble
307 NVS Read Error
308 New System
309 Fw Update Fail
310 Inv sFib Fbr Cfg
311 Inv Invtr FbrCfg
312 Inv Conv Fbr Cfg
313 Inv CSB Fbr Cfg
314 Inv DCP Fbr Cfg
315 Inv ACP Fbr Cfg
316 Inv MVFB Fbr Cfg
318 Unknown Device
319 DPI Card Wrg Slt
320 Vlt Class Mismth
321 Inv Dev in Cfg
322 Op Mode Mismth
323 Inv FR Id
324 CatalogId NotFnd
325 Inv Conn Opt
326 Prllel Fr Mismth
327 DVDT Fltr Mismth
328 Inv AFE mode
330 No SysId Match
331 Unknow Op Mode
332 SafetyPortCnflct
333 NVS Write Error
334 Inv TAM Config
335 Inv Filtr Config
337 MtrCtrl Mismatch
338 App Mismatch
339 Emb Mismatch
340 Net IO Fault
341 Net Idle Fault
342 Net Msg Fault
344 SafetyInit Error
345 Sec MtrCtrl Chng
346 Invalid DL Cfg
347 VelUnit Mismatch
348 Vltg Class Cfg
349 DutyRatingMismth
350 Net Link 1 Up
351 Net Link 1 Down
352 Net Link 2 Up
353 Net Link 2 Down
354 Net Dup Address
355 Invalid Net Cfg
356 BOOTP Response
357 DHCP Response
358 DHCP Renew
359 DHCP Rebind
360 DHCP Release
361 Net Sent Reset
362 Net IO Open
363 Net IO Idle
364 Net IO Close
365 Net IO Timeout
366 Net IO Abort
367 PCCC IO Open
368 PCCC IO Close
369 PCCC IO Timeout
370 Msg Ctrl Open
371 Msg Ctrl Close
372 Msg Ctrl Timeout
375 Net Ring Up
376 Net Ring Down
103 Device Timeout
200 Image Wtchdg Flt
201 Const Inv Flt
202 Const Chksum Flt
203 Fiber Offline 0
204 Fiber Offline 1
205 Fiber Offline 2
206 Fiber Offline 3
207 Fiber Offline 4
208 Fiber Offline 5
209 Fiber Offline 6
210 Fiber Offline 7
211 Fiber Offline 8
212 Fiber Offline 9
213 Fiber Offline 10
225 HSI Offline 0
226 HSI Offline 1
227 Over Temp Alarm
228 Over Temp Fault
229 Under Temp Alarm
230 Under Temp Fault
231 FdbkMsg Fiber 0
232 FdbkMsg Fiber 1
233 FdbkMsg Fiber 2
234 FdbkMsg Fiber 3
235 FdbkMsg Fiber 4
236 FdbkMsg Fiber 5
237 FdbkMsg Fiber 6
238 FdbkMsg Fiber 7
239 FdbkMsg Fiber 8
240 FdbkMsg Fiber 9
241 FdbkMsg Fiber 10
253 Inv U Phase Cur
254 Inv V Phase Cur
255 Inv W Phase Cur
256 Inv U Phase NTC
257 Inv V Phase NTC
258 Inv W Phase NTC
259 Inv DC Bus Range
260 Cnv U Phase Cur
261 Cnv V Phase Cur
262 Cnv W Phase Cur
263 Cnv U Phase NTC
264 Cnv V Phase NTC
265 Cnv W Phase NTC
266 Cnv DC Bus Range
267 Flash Timeout
268 FlashRst Timeout
269 Login Timeout
270 Flash DPI Error
271 NVS Checksum Flt
9002 DLX IO Cfg Invld
9003 DLX Checksum
9004 EmbLogic Adapter
9012 TP MtrCtrl Mode
9013 Torq Prove Cflct
9014 TP Encls Config
9015 TP Sec Mtr Ctrl
9016 PID MtrCtrl Port
9048 Sleep Config
9049 Waking
9050 SleepMtrCtrl Cfg
9086 OW TrqLvlTimeout
9087 OW Torq High
9088 Pump Off
9089 PumpJack SecMtr
9090 OW Torq Low
9091 OW MtrCtrl Cflct
10001 Power Loss
11001
10002 Mtr Ovrld Alarm
11002
10003 Motor Overload
11003
10004 Load Loss
11004
10005 Input Phase Loss
11005
10007 TorqPrv Spd Band
11007
10008 Output PhaseLoss
11008
10009 Decel Inhibit
11009
10010 OverSpeed Limit
11010
10011 BrakeSlippedActv
11011
10012 BrakeSlippedStop
11012
10014 Invld DC Bus Ref
11014
10015 OverFreq Limit
11015
10016 Phase U to Grnd
11016
10017 Phase V to Grnd
11017
10018 Phase W to Grnd
11018
10019 Phase UV Short
11019
10020 Phase VW Short
11020
10021 Phase WU Short
11021
10022 Phase UNegToGrnd
11022
10023 Phase VNegToGrnd
11023
10024 Phase WNegToGrnd
11024
10025 Shear Pin 1
11025
10026 Shear Pin 2
11026
10027 Drive OverLoad
11027
10028 Drive OverLoad
11028
10029 Stator Res Range
11029
10030 FluxAmpsRef Rang
11030
10031 Excessive Load
11031
10032 AutoTune Aborted
11032
10033 Leakage L Range
11033
10034 StcOffstPulsFail
11034
10035 StcOffstRtrFail
11035
10038 Auto Tach Switch
11038
10039 Start On PowerUp
11039
10040 Ext Prechrg Err
11040
10041 PrechargeOpenAlm
11041
10042 PrechargeOpenFlt
11042
10043 Autn Enc Angle
11043
10044 Autn Vel Rstrct
11044
10045 Autotune CurReg
11045
10046 Autotune Travel
11046
10047 No Stop Source
11047
10048 Accel Limit
11048
10049 Decel Limit
11049
10050 PWM Freq Reduced
11050
10051 CurLimit Reduced
11051
10053 Pos Over Travel
11053
10054 Neg Over Travel
11054
10055 Travel Lim Cflct
11055
10056 Profiling Active
11056
10057 Homing Active
11057
10058 Home Not Set
11058
10059 Invld Homing Cfg
11059
10060 Fwd End Limit
11060
10061 Rev End Limit
11061
10063 Freq Conflict
11063
10064 VHz Neg Slope
11064
10065 VHz Boost Limit
11065
10066 VHz Curve Incomp
11066
10067 DynBrake OvrTemp
11067
10068 MVFB Thrshld Exd
11068
10069 SyRSpdEstErr
11069
10070 Fwd Spd Lim Cfg
11070
10071 Rev Spd Lim Cfg
11071
10072 PM Offset Cnflct
11072
10073 IPMSpdEstErr
11073
10075 DynOffstFail
11075
10076 Excess Psn Err
11076
10080 M Ground Warning
11080
10081 HRG Gnd Warn
11081
10082 HRG Gnd Warn Lcl
11082
10083 Fdbk Data Late
11083
10084 PWM Data Late
11084
10085 IPM OverCurrent
11085
10086 PTP Solver Fail
11086
10087 VRef Solver Fail
11087
10092 SW OverCurrent
11092
10093 HW OverCurrent
11093
10094 Heatsink OvrTemp
11094
10095 125us Task Ovr
11095
11096
10097 1ms Task Ovr
11097
10098 2ms Task Ovr
11098
10099 10ms Task Ovr
11099
10100 100ms Task Ovr
11100
10101 CntrlTask Wtchdg
11101
10102 SystmTask Wtchdg
11102
10103 1ms Task Wtchdg
11103
11104
11105
10106 UnderVoltage
11106
10107 OverVoltage
11107
10109 HeatSinkUnderTmp
11109
10110 Autotune Inertia
11110
10111 Inv App No Strt
11111
10112 InvalidLoadRatio
11112
10113 SlipInvalidRange
11113
10114 Jnt OverTemp Flt
11114
10115 Odd Motor Poles
11115
10118 Ld00 Fail
11118
10119 Ld100 Fail
11119
10120 Lq Fail
11120
10121 ChgPmpProtActive
11121
10122 SyR OpenLoop PWM
11122
10129 Pred Maint Reset
11129
10130 MtrSide Started
11130
10131 MtrSide Stopped
11131
10132 InvldAutnTestCfg
11132
10177 Mtr Brng Life
11177
10178 Mtr Lube Life
11178
10179 Mch Brng Life
11179
10180 Mch Lube Life
11180
12002 ConstantsMsgIvld
12003 Constants Chksum
12005 Power Supply UV
12006 Precharge Fault
12007 MCS CL BayOTmp
12008 MCS Shunt Trip
12009 MCS Aux Mismatch
12010 240VAC Loss Flt
12011 240VAC OV
12012 FDOpen MCSClose
12013 SysPwr OC Fault
12017 Gate Drive Flt
12018 Fiber Offline
12019 SysPwr OV Flt
12020 N24V UV Flt
12022 Pred NVS Error
12023 CtrlMsgWdog Tout
12024 TAM Cal Missing
12025 Incom GateDr Flt
12026 Ground Flt
12027 Bus OV Flt
12028 NTC-U Short Flt
12029 NTC-U Open Flt
12030 U OverTemp Flt
12031 U OverTemp Alm
12032 U LowTemp Flt
12033 U LowTemp Alm
12034 NTC-V Short Flt
12035 NTC-V Open Flt
12036 V OverTemp Flt
12037 V OverTemp Alm
12038 V LowTemp Flt
12039 V LowTemp Alm
12040 NTC-W Short Flt
12041 NTC-W Open Flt
12042 W OverTemp Flt
12043 W OverTemp Alm
12044 W LowTemp Flt
12045 W LowTemp Alm
12047 Jnt OverTemp Alm
12048 Str Overload Flt
12049 Str Overload Alm
12050 Bus Fuse Harness
12051 Bus PosFuseBlown
12052 Bus NegFuseBlown
12053 DCP MCS Life
12060 Volt Class Flt
12061 Duty Rating Flt
12062 Pwr UnitTyp Flt
12063 DTM ConstCorrFlt
12064 Main Blower Alm
12065 Main Blower Flt
12070 Board OT Alarm
12071 Board OT Fault
12072 Board UT Alarm
12073 Board UT Fault
12074 IntakeAirOT Alrm
12075 IntakeAir OT Flt
12076 IntakeAirUT Alrm
12077 IntakeAir UT Flt
12078 PIB OT Alarm
12079 PIB OT Fault
12080 PIB UT Alarm
12081 PIB UT Fault
12082 Offset Alm
12083 Bus Imbalanc Alm
12084 Bus Imbalanc Flt
12085 PWM Enable Flt
12086 L/R Overtemp
12087 BusCond BayOTmp
12088 Sec Fbk Watchdog
12089 ISO UV
12090 CabAirHiTempRise
12091 CabAirLoTempRise
12092 HS Fan Life
12093 IGBT Life
12094 Bus Cap Life
12095 Stir Fan Life
12096 U Pos IOC Flt
12097 V Pos IOC Flt
12098 W Pos IOC Flt
12099 U Neg IOC Flt
12100 V Neg IOC Flt
12101 W Neg IOC Flt
12102 LocPwr UV Flt
12103 Device Timeout
12104 P24 UV Flt
12107 DC Fuse Open
12108 240VAC Low
12109 240VAC Loss
12110 FDOpen MCSOpen
12126 Pwr Bd Alarm
12127 Pwr Bd Fault
12131 Flash Timeout
12133 Login Timeout
12134 Flash DPI Error
12136 Mtrside IOC Flt
12137 Pwr Struc Fault
13001 LnSyncLoss Det
13002 LnSyncLoss RTExp
13003 Phase Loss Det
13004 Phase Loss RTExp
13005 PowerLoss Det
13006 PowerLoss RTExp
13007 Line Sag Det
13008 Line Sag RTExp
13009 High df/dt Det
13010 High df/dt RTExp
13011 LineVltgUnbal
13012 LineCurUnbal
13013 AC L12 OvrVltg A
13016 AC L12 OvrVltg B
13019 AC L12 UndrVltgA
13022 AC L12 UndrVltgB
13025 AC L12 HiVltg A
13028 AC L12 HiVltg B
13031 AC L12 LoVltg A
13034 AC L12 LoVltg B
13037 AC Line OvrFreqA
13038 AC Line OvrFreqB
13039 AC Ln UndrFreq A
13040 AC Ln UndrFreq B
13041 AC Ln HiFreq A
13042 AC Ln HiFreq B
13043 AC Ln LoFreq A
13044 AC Ln LoFreq B
13046 Heatsink OvrTemp
13047 L Ground Warning
13048 HRG Gnd Warn
13049 HRG Gnd Warn Lcl
13050 Line Phase Rvs
13051 Fdbk Data Late
13052 PWM Data Late
13053 HW OverCurrent
13056 1ms Task Ovr
13057 2ms Task Ovr
13058 10ms Task Ovr
13059 100ms Task Ovr
13060 CntrlTask Wtchdg
13061 SystmTask Wtchdg
13065 SW Bus Low Volt
13066 OverVoltage
13067 Cnv App No Strt
13069 R Overload Flt
13070 R Overload Alm
13071 S Overload Flt
13072 S Overload Alm
13073 T Overload Flt
13074 T Overload Alm
13075 Bus Rate of Rise
13076 LineSide Started
13077 LineSide Stopped
13078 Frame 5 Actv Dmp
13092 SW OverCurrent
14002 ConstantsMsgIvld
14003 Constants Chksum
14005 Power Supply UV
14006 Precharge Fault
14007 MCB CL BayOTmp
14008 MCB Fail To Opn
14009 MCB Aux BayOTmp
14010 240VAC Loss Flt
14011 240VAC OV
14012 FDOpen MCBClose
14013 SysPwr OC Fault
14014 AC Fuse Open
14016 LEM b0 Flt
14017 Gate Drive Flt
14018 Fiber Offline
14019 SysPwr OV Flt
14020 N24V UV Flt
14022 Pred NVS Error
14023 CtrlMsgWdog Tout
14024 CapFailureCfg
14025 Incom GateDr Flt
14026 Ground Flt
14027 Bus OV Flt
14028 NTC-R Short Flt
14029 NTC-R Open Flt
14030 R OverTemp Flt
14031 R OverTemp Alm
14032 R LowTemp Flt
14033 R LowTemp Alm
14034 NTC-S Short Flt
14035 NTC-S Open Flt
14036 S OverTemp Flt
14037 S OverTemp Alm
14038 S LowTemp Flt
14039 S LowTemp Alm
14040 NTC-T Short Flt
14041 NTC-T Open Flt
14042 T OverTemp Flt
14043 T OverTemp Alm
14044 T LowTemp Flt
14045 T LowTemp Alm
14047 Jnt OverTemp Alm
14048 Hw Conflict Flt
14049 RatingMissingFlt
14050 R Overload Flt
14051 R Overload Alm
14052 S Overload Flt
14053 S Overload Alm
14054 T Overload Flt
14055 T Overload Alm
14056 CapOvrRsncCfg
14060 Volt Class Flt
14061 Duty Rating Flt
14062 Pwr UnitTyp Flt
14063 DTM ConstCorrFlt
14064 Main Blower Alm
14065 Main Blower Flt
14066 Stir Fan 1 Alarm
14067 Stir Fan 1 Fault
14068 Stir Fan 2 Alarm
14069 Stir Fan 2 Fault
14070 Board OT Alarm
14071 Board OT Fault
14072 Board UT Alarm
14073 Board UT Fault
14074 IntakeAirOT Alrm
14075 IntakeAir OT Flt
14076 IntakeAirUT Alrm
14077 IntakeAir UT Flt
14078 PIB OT Alarm
14079 PIB OT Fault
14080 PIB UT Alarm
14081 PIB UT Fault
14082 Offset Alm
14083 Bus Imbalanc Alm
14084 Bus Imbalanc Flt
14085 PWM Enable Flt
14086 L/R Overtemp
14087 BusCond BayOTmp
14088 Sec Fbk Watchdog
14089 ISO UV
14090 CabAirHiTempRise
14091 CabAirLoTempRise
14092 HS Fan Life
14093 IGBT Life
14094 Bus Cap Life
14095 Stir Fan Life
14096 R Pos IOC Flt
14097 S Pos IOC Flt
14098 T Pos IOC Flt
14099 R Neg IOC Flt
14100 S Neg IOC Flt
14101 T Neg IOC Flt
14102 LocPwr UV Flt
14103 Device Timeout
14104 P24 UV Flt
14107 DC Fuse Open
14108 240VAC Low
14109 240VAC Loss
14110 FDOpen MCBOpen
14111 InvalidRatingFlt
14112 Capacitor Fault
14113 Fan Ovrtemp Alm
14114 Fan OverTemp Flt
14115 Fan UdrTemp Alm
14116 Fan UdrTemp Flt
14117 CapResonanceAlrm
14118 CapResonance Flt
14119 Reactor OT Fault
14120 PCC Fail To Cls
14121 PCC Fail To Opn
14122 PCC Aux Mismatch
14123 MCB Trip Reset
14124 MCB Overcurrent
14125 LCL FltrCap Life
14126 AC Line Ovr Vltg
14127 ACP MCB Life
14128 ACP PCC Life
14130 TVSS Open
14131 Flash Timeout
14133 Login Timeout
14134 Flash DPI Error
14135 BusCapVltgImbal
14136 Lineside IOC Flt
14142 Prchrg3 Sec
14143 Prchrg30 Sec
nn000 Open Wire
nn000 Enc0 Open Wire
nn000 Ch0 LightSrc Err
nn001 Analog In0 Loss
nn001 Phase Loss
nn001 Enc0 Phase Loss
nn001 Ch0 SigAmp Err
nn001 High Temp
nn002 Analog In1 Loss
nn002 Quadrature Loss
nn002 Enc0 Quad Loss
nn002 Ch0 PsnVal Err
nn002 Over Temp
nn003 Ch0 OverVolt Err
nn003 Comm Watchdog
nn004 Safety Fdbk
nn004 Ch0 UndVolt Err
nn004 Fiber Offline
nn005 Relay0 Life
nn005 STO Fault
nn005 Ch0 OverCur Err
nn006 Relay1 Life
nn006 Ch0 Battery Err
nn006 Ext Pwr Loss
nn007 Sys Misconfig
nn008 Critical Flt
nn008 Drive Misconfig
nn009 MP Out Flt
nn009 Ch0 AnalSig Err
nn010 Anlg Cal Chksum
nn010 SS In Flt
nn010 Ch0 IntOfst Err
nn011 PTC Over Temp
nn011 Ch0 DataTabl Err
nn012 PTC ShortCircuit
nn012 Ch0 AnalLim Err
nn013 ATX Voltage Loss
nn013 Ch0 Int I2C Err
nn014 ThermostatOvrTmp
nn014 Ch0 IntChksm Err
nn015 ATEX Safety
nn015 Ch0 PrgmResetErr
nn016 Ch0 CntOvrflwErr
nn017 Ch0 Parity Err
nn018 Ch0 Chksum Err
nn019 Ch0 InvCmd Err
nn020 Ch0 SendSize Err
nn021 Ch0 CmdArgmt Err
nn022 Ch0 InvWrtAdrErr
nn023 Ch0 AccCode Err
nn024 Ch0 FieldSizeErr
nn025 Ch0 Address Err
nn026 Ch0 FieldAcc Err
nn028 Ch0 SiTurnPsnErr
nn029 Ch0 MulTrnPsnErr
nn030 Enc1 Open Wire
nn031 Enc1 Phase Loss
nn032 Enc1 Quad Loss
nn034 Pri VelFdbk Loss
nn035 Alt VelFdbk Loss
nn036 Aux VelFdbk Loss
nn036 Ch0 AnalVal Err
nn037 Pri PsnFdbkLoss
nn037 Ch0 SendCurr Err
nn038 Alt PsnFdbkLoss
nn038 Ch0 EncTemp Err
nn039 Ch0 Speed Err
nn040 Ch0 General Err
nn046 Ch0 LED Curr Err
nn047 Ch0 ExMulTurnErr
nn048 Ch0 PsnCode Err
nn049 Ch0 Config Err
nn051 Ch0 SerialComErr
nn052 Ch0 Ext Failure
nn053 Ch0 Temp Exc Err
nn058 Module Defaulted
nn064 Ch0 OutOfRailErr
nn068 Ch0 Read Head 1
nn070 Ch0 RAM Error
nn071 Ch0 EPROM Error
nn072 Ch0 ROM Error
nn074 Ch0 No Position
nn081 Ch0 Msg Cheksum
nn082 Ch0 Timeout
nn083 Ch0 Comm
nn084 Ch0 Diagnostic
nn085 Ch0 SpplyVltgRng
nn086 HW Enbl Jmpr Out
nn086 Ch0 SC Amplitude
nn087 Ch0 Open Wire
nn088 Safety Jmpr Out
nn088 Ch0 Quad Loss
nn089 Safety Jumper In
nn089 Ch0 Phase Loss
nn090 Ch0 Unsupp Enc
nn092 SafetyHealth Err
nn093 SafetyPwrOn Err
nn094 SafetyPwrOff Err
nn100 Ch0 FreqExc Alm
nn101 Ch0 TempExc Alm
nn102 Ch0 LightLim Alm
nn103 Ch0 Battery Alm
nn104 Ch0 RefPoint Alm
nn108 Ch0 General Alm
nn115 Ch0 Optics Alarm
nn116 Ch0 OutOfRailAlm
nn200 Ch1 LightSrc Err
nn201 Ch1 SigAmp Err
nn203 Ch1 OverVolt Err
nn204 Ch1 UndVolt Err
nn205 Ch1 OverCur Err
nn206 Ch1 Battery Err
nn209 Ch1 AnalSig Err
nn210 Ch1 IntOfst Err
nn212 Ch1 AnalLim Err
nn213 Ch1 Int I2C Err
nn214 Ch1 IntChksm Err
nn215 Ch1 PrgmResetErr
nn216 Ch1 CntOvrflwErr
nn217 Ch1 Parity Err
nn218 Ch1 Chksum Err
nn219 Ch1 InvCmd Err
nn220 Ch1 SendSize Err
nn221 Ch1 CmdArgmt Err
nn222 Ch1 InvWrtAdrErr
nn223 Ch1 AccCode Err
nn225 Ch1 Address Err
nn226 Ch1 FieldAcc Err
nn228 Ch1 SiTurnPsnErr
nn229 Ch1 MulTrnPsnErr
nn236 Ch1 AnalVal Err
nn237 Ch1 SendCurr Err
nn238 Ch1 EncTemp Err
nn239 Ch1 Speed Err
nn240 Ch1 General Err
nn244 Ch1 FieldSizeErr
nn246 Ch1 LED Curr Err
nn247 Ch1 ExMulTurnErr
nn248 Ch1 PsnCode Err
nn249 Ch1 Config Err
nn251 Ch1 SerialComErr
nn252 Ch1 Ext Failure
nn253 Ch1 Temp Exc Err
nn256 Ch1 OutOfRailErr
nn262 Ch1 RAM Error
nn263 Ch1 EPROM Error
nn264 Ch1 ROM Error
nn266 Ch1 No Position
nn281 Ch1 Msg Cheksum
nn282 Ch1 Timeout
nn283 Ch1 Comm
nn284 Ch1 Diagnostic
nn285 Ch1 SpplyVltgRng
nn286 Ch1 SC Amplitude
nn287 Ch1 Open Wire
nn288 Ch1 Quad Loss
nn289 Ch1 Phase Loss
nn290 Ch1 Unsupp Enc
nn300 Ch1 FreqExc Alm
nn301 Ch1 TempExc Alm
nn302 Ch1 LightLim Alm
nn303 Ch1 Battery Alm
nn304 Ch1 RefPoint Alm
nn308 Ch1 General Alm
nn315 Ch1 Optics Alarm
nn316 Ch1 OutOfRailAlm
nn412 Hardware Err
nn413 Firmware Err
nn416 EncOut Cflct
nn417 Safety Cflct
nn420 FB0FB1 Cflct
nn421 Initializing
nn534 Pri VelFdbk Loss
nn535 Alt VelFdbk Loss
nn536 Aux VelFdbk Loss
nn537 Pri PsnFdbkLoss
nn538 Alt PsnFdbkLoss
nn999 System Comm Loss
nn999 Bkplane Comm
Condition Type Condition Code Display Text Full Text
none 0 No Entry
Resettable Fault 1 Auxiliary Input Auxiliary Input
Resettable Fault 2 Sys Default Fail System Reset to Defaults Failure
Alarm 1 3 Emerg OVRD Actv Emergency Override Activated
Alarm 1 4 Energy Pause Cfg Invalid Energy Pause Configuration
Resettable Fault 6 SecureEraseCplt Secure Erase Complete
Event 7 EmergOVRD Actv Emergency Override Activated

Event 8 EmergOVRD Deactv Emergency Override Deactivated
Event 9 Firmware Started Firmware Started
Event 10 Firmware Stopped Firmware Stopped
Resettable Fault 15 AuRsts Exhausted Auto Restarts Exhausted
Alarm 1 16 CPU OverTemp Alm CPU Over Temperature Alarm
Resettable Fault 17 CPU OverTemp Flt CPU Over Temperature Fault
Resettable Fault 18 System Defaulted System Defaulted
Event 21 Clr Fault Queue Clear Fault Queue

Event 22 Clr Alarm Queue Clear Alarm Queue
Resettable Fault 23 Board OT Fault Control Board Overtemperature
Fault
Alarm 1 24 Board OT Alarm Control Board Overtemperature

Alarm
Resettable Fault 25 Board UT Fault Control Board Undertemperature
Fault
Alarm 1 26 Board UT Alarm Control Board Undertemperature

Alarm
Resettable Fault 27 Module Defaulted Module Defaulted
Resettable Fault 29 Port 1 Adapter Port 1 Adapter

Configurable 35 Port 1 DPI Loss Port 1 DPI Loss

Resettable Fault 38 Port 4 DPI Loss Port 4 DPI Loss
Resettable Fault 43 PwrDn NVS Blank Power Down NVS Blank
Non-Resettable 58 PwrDn Data Chksm Power Down Data Checksum

Fault
Event 60 New Firmware New Firmware

Event 61 Invalid RTC Time Invalid RTC Chip Time
Event 62 RTC HW Failed RTC Hardware Access Failed
Event 63 Time Change Time Change Event
Event 64 Pwr Cyc Cnt Ovf Power Cycle Change Count Overflow
Event 65 Time Chg Cnt Ovf Time Change Count Overflow

Alarm 1 66 PwrDn Backup Power Down Backup
Resettable Fault 67 PwrDn Data Fail Power Down Data Failure
Alarm 1 68 PwrDn Sig Fail Power Down Signal Failure
Event 69 Cond Data Lost Condition Data Corrupt
Event 70 Firmware Update Firmware Update

Alarm 2 71 Bipolar Conflict Bipolar Conflict
Resettable Fault 72 Digin Regen Fail Digital Input Regeneration Failure
Alarm 2 73 DigIn Cfg B Digital Input Configuration B
Alarm 2 74 DigIn Cfg C Digital Input Configuration C
Event 77 Drive Reset Drive Reset

Alarm 1 78 Pod Fan Alarm Pod Fan Alarm
Event 80 Drive Faulted Drive Faulted

Event 82 Clr Event Queue Clear Event Queue
Event 83 Clr Excptn Queue Clear Exception Queue
Configurable 84 MixedCorrProt Mixed Corrosion Protection
Resettable Fault 86 HW Enbl Jmpr Out Hardware Enable Jumper Out

Non-Resettable 87 Safety Brd Fault Safety Board Fault
Fault
Non-Resettable 88 Safety Jmpr Out Safety Jumper Out

Fault
Non-Resettable 89 Safety Jumper In Safety Jumper In

Fault
Non-Resettable 92 SafetyHealth Err SafetyHealth Error

Fault
Non-Resettable 93 SafetyPwrOn Err SafetyPwrOn Error

Fault
Non-Resettable 94 SafetyPwrOff Err Safety Power Off Error
Fault
Non-Resettable 95 FS Enbl Ch Error FS Enable Channel Error

Fault
Alarm 2 104 Port 4 Cfg Port 4 Configuration

Non-Resettable 128 LC Incomp PFB Liquid Cooled Incompatible Power

Fault Fdbk Bd
Event 129 Prev Maint Reset Predictive Maintenance Reset

Configurable 131 In Fan Life Input Bay Fan Life
Configurable 132 Pod Fan Life Control Pod Fan Life
Configurable 133 Pwr Rf Fan Life Power Bay Roof Fan Life
Configurable 134 Wrg Bay Fan Life Wiring Bay Fan Life
Configurable 135 CtrlBay Fan Life Control Bay Fan Life
Resettable Fault 171 No Stop Source All Logic Control Sources

Disconnected
Configurable 174 TAM Det Not Cfg Torque Accuracy Module Detected
Not Configured
Alarm 2 175 TAM Cfg Not Det Torque Accuracy Module Configured
Not Detected
Alarm 2 176 InvldDataSource Invalid Indirect Selection
Configurable 177 NonStdDataSource Non Standard Data Source
Alarm 2 180 Invld 2Wire Cfg Invalid 2 Wire Configuration
Resettable Fault 300 Nvs Lost Config Nonvolatile Storage Config File Lost
Non-Resettable 301 Pfile Create Err Profile Creation Error

Fault
Non-Resettable 302 Pfile Login Err Profile Login Error

Fault
Resettable Fault 303 HSI Offline HSI Offline
Resettable Fault 304 AFE PreChrg Fail AFE PreCharge Failure
Resettable Fault 305 No Sfib Detected No SFIB Detected
Alarm 1 306 HW Not Compatble Hardware Not Compatible
Non-Resettable 307 NVS Read Error NVS Read Error

Fault
Alarm 2 308 New System New System
Non-Resettable 309 Fw Update Fail Firmware Update Failed

Fault
Non-Resettable 310 Inv sFib Fbr Cfg Invalid SFIB Fiber Configuration
Fault
Non-Resettable 311 Inv Invtr FbrCfg Invalid Inverter Fiber Configuration

Fault
Non-Resettable 312 Inv Conv Fbr Cfg Invalid Converter Fiber Configuration
Fault
Non-Resettable 313 Inv CSB Fbr Cfg Invalid CSB Fiber Configuration
Fault
Non-Resettable 314 Inv DCP Fbr Cfg Invalid DCP Fiber Configuration
Fault
Non-Resettable 315 Inv ACP Fbr Cfg Invalid ACP Fiber Configuration
Fault
Non-Resettable 316 Inv MVFB Fbr Cfg Invalid TAM Fiber Configuration
Fault
Non-Resettable 318 Unknown Device Unknown Device In System

Fault
Non-Resettable 319 DPI Card Wrg Slt DPI Card In Wrong Slot
Fault
Non-Resettable 320 Vlt Class Mismth Voltage Class Mismatch

Fault
Non-Resettable 321 Inv Dev in Cfg Invalid Device In Configuration

Fault
Non-Resettable 322 Op Mode Mismth Operational Mode Mismatch

Fault
Non-Resettable 323 Inv FR Id Invalid Frame Rating ID

Fault
Non-Resettable 324 CatalogId NotFnd Catalog ID Not Found
Fault
Non-Resettable 325 Inv Conn Opt Invalid Connected Option

Fault
Non-Resettable 326 Prllel Fr Mismth Parallel Frame Mismatch
Fault
Non-Resettable 327 DVDT Fltr Mismth DVDT Filter Mismatch

Fault
Non-Resettable 328 Inv AFE mode Invalid AFE Mode

Fault
Non-Resettable 330 No SysId Match No System ID Match

Fault
Non-Resettable 331 Unknow Op Mode Unknown Operational Mode

Fault
Alarm 2 332 SafetyPortCnflct Safety Port Conflict
Alarm 1 333 NVS Write Error NVS Write Error

Resettable Fault 334 Inv TAM Config Invalid TAM Configuration
Resettable Fault 335 Inv Filtr Config Invalid Filter Configuration
Alarm 2 337 MtrCtrl Mismatch Motor Control Mode Mismatch
Alarm 2 338 App Mismatch Application Mismatch
Alarm 2 339 Emb Mismatch Embedded Logic Mismatch
Configurable 340 Net IO Fault Network I/O Fault
Configurable 341 Net Idle Fault Network Idle Fault
Configurable 342 Net Msg Fault Network Messaging Fault

Non-Resettable 344 SafetyInit Error Safety Initialization Error
Fault
Alarm 2 345 Sec MtrCtrl Chng Secondary Motor Control Mode

Changed
Alarm 2 346 Invalid DL Cfg Invalid Datalink Configuration
Alarm 2 347 VelUnit Mismatch Velocity Units Mismatch
Alarm 2 348 Vltg Class Cfg Voltage Class Configuration
Alarm 2 349 DutyRatingMismth Duty Rating Mismatch
Event 350 Net Link 1 Up Network Link 1 Up

Event 351 Net Link 1 Down Network Link 1 Down
Event 352 Net Link 2 Up Network Link 2 Up
Event 353 Net Link 2 Down Network Link 2 Down
Event 354 Net Dup Address Network Duplicate Address
Event 355 Invalid Net Cfg Invalid Network Configuration
Event 356 BOOTP Response BOOTP Response

Event 357 DHCP Response DHCP Response
Event 358 DHCP Renew DHCP Renew
Event 359 DHCP Rebind DHCP Rebind
Event 360 DHCP Release DHCP Release

Event 361 Net Sent Reset Network Sent Reset
Event 362 Net IO Open Network IO Open
Event 363 Net IO Idle Network IO Idle
Event 364 Net IO Close Network IO Close

Event 365 Net IO Timeout Network IO Timeout
Event 366 Net IO Abort Network IO Abort
Event 367 PCCC IO Open PCCC IO Open
Event 368 PCCC IO Close PCCC IO Close
Event 369 PCCC IO Timeout PCCC IO Timeout
Event 370 Msg Ctrl Open Message Control Open
Event 371 Msg Ctrl Close Message Control Close
Event 372 Msg Ctrl Timeout Message Control Timeout
Event 375 Net Ring Up Network Ring Up
Event 376 Net Ring Down Network Ring Down
Resettable Fault 103 Device Timeout Device Message Timeout
Resettable Fault 200 Image Wtchdg Flt Image Watchdog Fault

Non-Resettable 201 Const Inv Flt Constants Message Invalid Fault
Fault
Non-Resettable 202 Const Chksum Flt Constants Checksum Fault

Fault
Resettable Fault 203 Fiber Offline 0 Fiber Online to Offline 0




Resettable Fault 225 HSI Offline 0 HSI Online to Offline 0

Resettable Fault 226 HSI Offline 1 HSI Online to Offline 1
Alarm 1 227 Over Temp Alarm Board Over Temperature Alarm
Resettable Fault 228 Over Temp Fault Board Over Temperature Fault
Alarm 1 229 Under Temp Alarm Board Under Temperature Alarm
Resettable Fault 230 Under Temp Fault Board Under Temperature Fault
Resettable Fault 231 FdbkMsg Fiber 0 Feedback Msg Timeout Fiber 0





Alarm 1 253 Inv U Phase Cur Inverter U Current Imbalance
Alarm 1 254 Inv V Phase Cur Inverter V Current Imbalance
Alarm 1 255 Inv W Phase Cur Inverter W Current Imbalance
Alarm 1 256 Inv U Phase NTC Inverter U Current Imbalance

Inverter U NTC Imbalance
Alarm 1 257 Inv V Phase NTC Inverter V Current Imbalance

Inverter V NTC Imbalance
Alarm 1 258 Inv W Phase NTC Inverter W Current Imbalance
Inverter W NTC Imbalance
Resettable Fault 259 Inv DC Bus Range Inverter DC Bus Imbalance
Alarm 1 260 Cnv U Phase Cur Converter U Current Imbalance
Alarm 1 261 Cnv V Phase Cur Converter V Current Imbalance
Alarm 1 262 Cnv W Phase Cur Converter W Current Imbalance
Alarm 1 263 Cnv U Phase NTC Converter U NTC Imbalance

Alarm 1 264 Cnv V Phase NTC Converter V NTC Imbalance
Alarm 1 265 Cnv W Phase NTC Converter W NTC Imbalance
Resettable Fault 266 Cnv DC Bus Range Converter DC Bus Imbalance
Alarm 1 267 Flash Timeout HSI Flash Timeout
Alarm 1 268 FlashRst Timeout HSI Flash Reset Timeout
Alarm 1 269 Login Timeout HSI Login Timeout
Alarm 1 270 Flash DPI Error Flash DPI Error
Non-Resettable 271 NVS Checksum Flt Nonvolatile Data Checksum Fault

Fault
Fault
The auxiliary fault digital input is open or reset.
A command to reset parameter defaults has failed.

The values of some parameters have not been changed.
Emergency override is activated.

Faults in the groups that are configured in parameter 0:455 [Emerg Prot OVRD]
are ignored if set while emergency override is activated.
If faults groups are ignored, the life span of the product can be shortened.
Replacement of the product is recommended after the emergency has passed.
The transition to energy pause cannot be completed because power is not

supplied to the designated 24V DC auxiliary input.
The requested secure operation has completed. User-configurable settings

have been erased from the product’s memory.
Emergency override has been activated.

Emergency override has been deactivated.
The application program is starting.
Control power was removed.
The drive unsuccessfully attempted to reset a fault and resume running for the
programmed number of tries.
The temperature of the main microprocessor (CPU) on the main control board
has exceeded the alarm threshold (103 °C).
See Diagnostic item 77 ‘MPU Temp C’ in port 0.
The temperature of the main microprocessor (CPU) on the main control board
has exceeded the fault threshold (107 °C).
See Diagnostic item 77 ‘MPU Temp C’ in port 0.
A command to reset parameter defaults on all ports has been executed.

See code 27 ‘Module Defaulted’ for reset of a single port.
A command to clear the fault queue has been executed.

A command to clear the alarm queue has been executed.
The temperature of the main control board has exceeded the fault threshold,
which differs based on product:
• The fault threshold is 90 °C for PowerFlex 755TR, 755TL, and 755TM products
and for 755TS products with the control pod fan on.
• The fault threshold is 80 °C for PowerFlex 755TS products with the control
pod fan off.
Possible causes include high ambient temperature and obstructed airflow.
The control pod temperature is reported by parameter 0:25 [Ctrl Pod Temp].
The temperature of the main control board has exceeded the alarm threshold,
which differs based on product:
• The alarm threshold is 85 °C for PowerFlex 755TR, 755TL, and 755TM
products and for 755TS products with the control pod fan on.
• The fault threshold is 75 °C for PowerFlex 755TS products with the control
pod fan off.
The temperature of the main control board has fallen below the fault
temperature (-25 °C).
Possible causes include low ambient temperature.
The temperature of the main control board has fallen below the alarm
temperature (-15 °C).
A command to reset parameter defaults on a single port has been executed.

This fault also sets when secure erase has been completed for the product.
See code 18 ‘System Defaulted’ for reset of all ports.
The DPI communications adapter in port 1 has a fault.

Port 1 is the HIM cradle on the control pod.

Port 2 is usually a HIM or a 1203-USB adapter.

Port 4 is backplane option slot 4.


The DPI communications adapter in port 1 has stopped communicating with

the main control board.
Port 1 is the HIM cradle on the control pod.


main control board.
Port 4 is a backplane connection, slot 4.

main control board.

main control board.
An internal data error occurred.

This fault occurs on power down but is checked for on power-up.
If the power down occurs too fast, this fault can occur.
If you are using an undersized auxiliary power supply and the last power down
was from auxiliary power, this fault can occur.
Checksum failed for non-volatile data.
New firmware detected at power up.

The real time clock (RTC) does not return the value that is written to it.
The real time clock (RTC) hardware and software function are not properly
synchronized.
The value of the real time clock (RTC) has been adjusted to match an external
source.
The power cycle counter has rolled over (from 65535 to 0).
The time change counter has rolled over (from 65535 to 0).
The back-up power down information has been restored in place of the main
power down data due to the main data being erased or corrupted.
The stored power down data has failed to be retrieved 3 or more times.
This fault is clearable upon power-up.
Faults continue on power-up until the main control board is replaced.
The power down signal for the main control board has failed.
This condition prevents storing of power down data for the application,
including energy meters and predictive maintenance data.
Condition data was determined to be corrupt or missing at power up.
An event to update the firmware image on the product has been triggered.
During a firmware update, the product does not accept I/O connections, and it
cannot be started.
Parameter 10:930 [Direction Mode] is set to 1 ‘Bipolar’ or 2 ‘Rev Disable’ and
one or more digital inputs is enabled for direction control, such as parameter
0:130 [DI M Fwd Reverse].
Digital input signal from a regenerative power supply or third-party bus supply
indicates a regeneration fault.
This condition is applicable to common bus inverters only.
There is a digital input conflict.

Input functions that cannot exist simultaneously have been selected (for
example run and start).
See the configuration table on the Tables & Graphics tab.
There is a digital input conflict.

Input functions that cannot be assigned to the same digital input have been
selected (for example run and stop).
See the configuration table on the Tables & Graphics tab.
A command to reset the product has been received.

On drives that have a control pod fan, the fan is inoperative.
On drives that do not have a control pod fan, the bypass jumper is removed,
missing, or not seated properly.
A fault has occurred in the product.

A command to clear the event queue has been executed.
A command to clear the exception queue has been executed.
One or more of the power peripherals that is installed in a PowerFlex 755TL,
755TR, or 755TM product does not provide XT protection from corrosive gases.
Power peripherals include inverter power structures, converter power
structures, and LCL filter modules.
The lifespans of components without XT protection can be shorter than the
lifespans of components with XT protection in some environments.
To acknowledge this limitation, set parameter 0:480 [MixedCorProtActn] to
ignore and cycle power to the product.
A safety option module is present and the hardware enable jumper is removed.
A Safety option module has indicated a fault. Verify that enable jumper is
installed. Reset or power cycle drive.
Integrated Safety Functions (20-750-S4):
• See publication 750-UM005 for more information.
Integrated Safety (20-750-S3):
Safe Speed Monitor (20-750-S1):
• See publication 750-RM001 for more information.
Safe Torque Off (20-750-S):
• If DC power drops below 17V DC ‘Not Enable’ is indicated.
• If voltage drops below 11V DC the module faults.
ATEX (20-750-ATEX):
• Possible hardware damage.
• The motor to the thermal sensor is shorted.
• Excessive EMC noise due to improper grounding/shielding.
Safety jumper is removed and a safety option module is not present.
Safety jumper is installed and a safety option module is present.
Safety jumper is installed with incorrect safety circuit status.

This fault indicates a hardware anomaly.
Safety option card is not detected or a 20-750-ATEX option module is present

while safety power is OFF (rather than ON). Indicates a hardware anomaly.
Safety option card is detected while safety power is ON (rather than OFF).
This fault indicates a hardware anomaly.
A functional safety enable channel fault is detected and no safety option is

present.
This fault indicates a hardware anomaly with the enable circuitry.
An invalid option module is detected in port 4.
The main control board has detected a configuration change since power
down.
The main control board has detected a configuration change since power
down.
An incompatible power feedback board is installed in a liquid-cooled PowerFlex

755TR drive.
Predictive maintenance function has reset an elapsed life parameter.

The elapsed percent life of the input bay fans has exceeded the configured
event threshold.
Elapsed percent life of the control pod fans has exceeded the configured event
threshold.
Elapsed percent life of the power bay roof fans has exceeded the configured
event threshold.
Elapsed percent life of the wiring bay roof fans has exceeded the configured
event threshold.
Elapsed percent life of the control bay fans has exceeded the configured event
threshold.
Not applicable to 755TL drives, 755TR drives, or 755TM bus supplies.
The last source for a stop command to the motor side inverter has been
removed or disconnected.
Sources can include a digital input, communication link to a controller, or a
HIM.
The drive has detected a Torque Accuracy module, but is not configured for
one.
Bit 0 ‘Module Enbl’ is cleared in parameter 12:55 [Trq Accy Mod Cfg], but
parameter 0:83 [TAM Option Act] is equal to 1 ‘Installed’.
The drive has not detected a Torque Accuracy module, but is configured for
one.
The value of parameter 0:83 [TAM Option Act] is 0 ‘NotInstalled’, but bit 0
‘Module Enbl’ is set in parameter 12:55 [Trq Accy Mod Cfg].
An indirect selector parameter is selecting a non-existent parameter or data

source.
This alarm can occur if a selector is directed to a source that has been removed.
Sources can include option cards and modular control profiles, such as the
configurable motor control in port 10.
For example, parameter 0:108 [DI M Stop] is selecting a digital input on an I/O
card in slot 4 and the option card has been removed from slot 4.
An indirect selector parameter is selecting a parameter or data source that is

not included in the selection lists for the parameter.
Run level logic is configured, but no digital input signal is configured for a run
logic command.
The configuration file that is stored in nonvolatile memory is corrupt.
Main control board firmware failed to create a profile for one of the power
peripherals.
One of the power peripherals has attempted to log in with an invalid ID.
The main control board has lost communication with the fiber interface circuit
board.
This fault can occur during a firmware update.
AC precharge has failed.

DC bus voltage has failed to rise to the proper level in the time allotted.
Main control board firmware failed to connect to the fiber interface circuit
board.
Main control board firmware has found power peripherals (PLI boards, CSBs,
and AC precharge modules) that are incompatible.
Main control board firmware failed to read non volatile storage memory.
Main control board firmware has detected a new configuration of power

peripherals.
The firmware update for a power peripheral has failed.
Main control board firmware has detected an invalid connection to the fiber
interface circuit board.
Main control board firmware has detected an invalid motor side inverter
connection to the fiber interface circuit board.
Main control board firmware has detected an invalid line side converter
connection to the fiber interface circuit board.
Main control board firmware has detected an invalid current sense board (CSB)
fiber-optic connection.
Main control board firmware has detected an invalid DC precharge fiber

connection.
Main control board firmware has detected an invalid AC precharge connection

to the fiber interface circuit board.
Main control board firmware has detected an invalid torque accuracy module
(TAM) connection to the fiber interface circuit board.
Main control board firmware has detected an unknown backplane option card
or an unsupported 20-COMM option card is installed.
Main control board firmware has detected a DPI backplane option board in a
non-DPI backplane option slot. Only the lower slots (4, 5, and 6) support DPI.
Backplane option cards that require DPI cannot function in slots 7 and 8.
Main control board firmware has detected a voltage class mismatch between
power peripherals (power modules, LCL filter modules, or precharge modules).
For example, one power peripheral is of the 400/480V voltage class while the
others are 600/690V.
Main control board firmware has detected power peripherals (power modules,
LCL filter modules, or precharge modules) that is not a valid peripheral type.
Main control board firmware has detected an operational mode mismatch.
Main control board firmware has detected an invalid frame rating ID.
Main control board firmware has failed to find the catalog ID.
Main control board firmware has detected an invalid LCL filter configuration.
The LCL filter module does not match the expected channel assignment.
Main control board firmware has detected an invalid combination of line side
converter power modules and LCL filter modules.
Main control board firmware has detected an invalid combination of motor side
inverter power modules with and without dv/dt filters.
Either all power modules in the motor side inverter must have dv/dt filters or
none of them must have the filters.
Main control board firmware has detected power modules in the line side
converter with dv/dt filters.
None of the power modules in the line side converter can have dv/dt filters.
The system does not recognize the product type.
Unknown Operating Mode was provided by a power layer interface (PLI) circuit
board.
Multiple functional safety option modules are installed. Only one safety option
module (non-ATEX) is allowed to be installed.
Or, a functional safety option module is installed and a 20-750-ATEX option
module is also installed with safety configuration switch S1-1 set to on.
Main control board firmware has failed to write to non volatile storage (NVS).
Main control board firmware has detected a torque accuracy module (TAM)
connected to an invalid channel on the fiber interface circuit board.
Main control board firmware has detected a current sense board (CSB)
connected to an invalid power layer interface (PLI) circuit board.
For paralleled converter power modules, the CSB fiber-optic cable connects to
the lower numbered Ln module.
Example for L0 and L1, the CSB connects to L0.
The configured and actual motor control mode do not match.

The value of parameter 0:66 [Pri MtrCtrl Act] is different than parameter 0:65
[Pri MtrCtrl Mode].
The configured and actual application mode do not match.

The value of parameter 0:71 [Application Act] is different than parameter 0:70
[Application Sel].
Value of 0:72 [Emb Logic Select] does not match the value of 0:73 [Emb Logic
Act] (the configured embedded logic does not match the actual embedded
logic).
The network I/O connection has timed out.

This condition can be raised while the I/O connection control source is in run
mode.
This condition closes all open explicit messaging connections.
Idle packets were received on the network I/O connection.

This condition can be raised after transitioning to idle mode from run mode.
Explicit messaging control has timed out.

Safety system failed to initialize due to unexpected discrepancy in detected
fiber peripherals.
The configured and actual secondary motor control modes do not match.
The value of parameter 0:68 [Sec MtrCtrl Act] is different than parameter 0:67
[Sec MtrCtrl Mode].
Two or more input datalinks are configured to write to the same target
parameter.
The configured and actual velocity units do not match.
The value of parameter 0:46 [Velocity Units] is different than parameter 0:47
[Vel Units Act].
The configured voltage class does not match the actual voltage class for the
product. The value of parameter 0:33 [VoltageClass Cfg] is different than the
value of parameter 0:34 [VoltageClass Act].
The configured duty rating does not match the actual duty rating for the
product. The value of parameter 0:35 [Duty Rating Cfg] is different than the
value of parameter 0:36 [Duty Rating Act].
The interface established a network link on its ENET1 network port.

The interface lost the network link on its ENET1 network port.
The interface established a network link on its ENET2 network port.
The interface lost the network link on its ENET2 network port.
Another device having the same IP address as the interface was detected on
the network.
The interface-network address configuration parameters are invalid, or the
network address that is provided by the BOOTP or DHCP server is invalid.
The interface received a response to its BOOTP request.

The interface received a response to its DHCP request.
The interface renewed its network address lease with the DHCP Server.
The interface rebinded its network address lease with the DHCP Server.
The interface network address lease expired.

The interface received a reset command from the network.
The I/O connection from the network to the interface has been opened.
The interface received I/O connection ‘idle’ packets from the network.
The I/O connection from the network to the interface was closed.
The interface I/O connection has timed out.
The interface I/O connection was aborted because the datalink configuration
was changed.
The interface began receiving PCCC control messages after the PCCC Control
Timeout was set to a nonzero value.
The device that sends PCCC control messages to the interface (for example, the
Control Bar feature in Connected Components Workbench) has set the PCCC
Control Timeout to zero.
The interface has not received a PCCC control message before the PCCC Control
Timeout.
Msg Ctrl Open
The timeout attribute in the CIP-based network Assembly Object was set to a
nonzero value.
This value allows control messages to be sent to the interface via the CIP-based
network Assembly Object.
Msg Ctrl Close

The timeout attribute in the CIP-based network Assembly Object was set to
zero.
A setting of zero does not allow control messages to be sent to the interface via
the CIP-based network Assembly Object.
Msg Ctrl Timeout

The interface has not received a control message via the CIP-based network
Assembly Object before the object timeout attribute triggered.
Net Ring Up
The Device Level Ring (DLR) status is Normal.
Net Ring Down
The Device Level Ring (DLR) status is Faulted.
The main control board has detected that one of the power peripherals (power
layer interface board, current sense board, or precharge board) has stopped
transmitting messages.
Communication between the main control board and the image buffer in one of
the power peripherals (power layer interface board, torque accuracy module,
or DC precharge board) has stopped transmitting for 10 milliseconds.
The constants header information did not match the content that is expected
by the power peripheral (power layer interface board, current sense board, or
precharge board).
The constants download failed the checksum check by the power peripheral
(power layer interface board, current sense board, or precharge board).
The fiber-optic communication link between the main control board and M0 PLI
transitioned from online to offline.
The fiber-optic communication link between the main control board and L0 PLI
The fiber-optic communication link between the main control board and ACPC0
The fiber-optic communication link between the main control board and the
torque accuracy module (TAM) or ACPC1 transitioned from online to offline.
The fiber interface circuit board has lost communication with the main control
board.
This fault concerns the fiber-optic cable connections to the motor side inverter.
The fiber interface circuit board has lost communication with the main control
board.
This fault concerns the fiber-optic cable connections to the line side converter.
The temperature of the fiber interface circuit board (Port 0 Diagnostic item
0:94 [sFIB Board Temp]) has exceeded the Alarm Temperature (75 °C).
0:94 [sFIB Board Temp]) has exceeded the Fault Temperature (80 °C).
0:94 [sFIB Board Temp]) has fallen below the Alarm Temperature (-25 °C).
The temperature of the fiber interface circuit board (FIB) (Port 0 Diagnostic
item 0:94 [sFIB Board Temp]) has fallen below the Fault Temperature (-30 °C).
Transmission of the feedback message from M0 PLI transitioned from online to

offline.
offline.

offline.

offline.

offline.

offline.
offline.

offline.

offline.

offline.
Transmission of the feedback message from L0 PLI transitioned from online to

offline.
offline.

offline.

offline.

offline.

offline.
offline.

offline.

offline.

offline.
Transmission of the feedback message from ACPC0 transitioned from online to

offline.
Transmission of the feedback message from the torque accuracy module
(TAM)/ACPC1 transitioned from online to offline.
There is an output current sharing imbalance between parallel inverters in the

phase indicated that is greater than 15% of the inverter rated current.
For example, the current of the U (T1) phase on the M0 power module is more
than 15% higher than the U (T1) phase on the M1 power module.

For example, the current of the V (T2) phase on the M0 power module is more
than 15% higher than the V (T2) phase on the M1 power module.

For example, the current of the W (T3) phase on the M0 power module is more
than 15% higher than the W (T3) phase on the M1 power module.
A thermal imbalance has occurred between parallel power modules on the U

(T1) phase. The temperature difference has exceeded 11.5 °C for 20 seconds or
longer.
For example, the temperature of the U (T1) phase on M0 (parameter 12:117
[M0 HeatsinkTempU]) is more than 11.5 °C higher than the U (T1) phase on M1
(parameter 12:217 [M0 HeatsinkTempU]).
A thermal imbalance has occurred between parallel power modules on the V

longer.
For example, the temperature of the V (T2) phase on M0 (parameter 12:118
[M0 HeatsinkTempV]) is more than 11.5 °C higher than the V (T2) phase on M1
(parameter 12:218 [M0 HeatsinkTempV]).
A thermal imbalance has occurred between parallel power modules on the W
longer.
For example, the temperature of the W (T3) phase on M0 (parameter 12:119
[M0 HeatsinkTempW]) is more than 11.5 °C higher than the W (T3) phase on
M1 (parameter 12:219 [M0 HeatsinkTempW]).
A DC bus voltage imbalance has occurred between parallel power modules. The
voltage difference has exceeded 50V for more than 2 minutes.
For example, parameter 12:109 [M0 DC BusVoltage] differs from parameter
12:209 [M1 DC BusVoltage] by more than 50V.
A current imbalance has occurred between parallel power modules on the R

(L1) phase.
The current difference has exceeded 15% of Line Side Converter rated current.
For example, the current of the R (L1) phase on the L0 power module is more
than 15% higher than the R (L1) phase on the L1 power module.
A current imbalance has occurred between parallel power modules on the S

(L2) phase.
For example, the current of the S (L2) phase on the L0 power module is more
than 15% higher than the S (L2) phase on the L1 power module.
A current imbalance has occurred between parallel power modules on the T

(L3) phase.
For example, the current of the T (L3) phase on the L0 power module is more
than 15% higher than the T (L3) phase on the L1 power module.
A thermal imbalance has occurred between parallel power modules on the R

(L1) phase.
The temperature difference has exceeded 11.5 °C for 20 seconds or longer.
For example, the temperature of the R (L1) phase on L0 power module is more
than 11.5 °C higher than the R (L1) phase on the L1 power module.
A thermal imbalance has occurred between parallel power modules on the S
(L2) phase.
For example, the temperature of the S (L2) phase on L0 power module is more
than 11.5 °C higher than the S (L2) phase on the L1 power module.
A thermal imbalance has occurred between parallel power modules on the T

(L3) phase.
For example, the temperature of the T (L3) phase on L0 power module is more
than 11.5 °C higher than the T (L3) phase on the L1 power module.
A DC bus voltage imbalance has occurred between parallel power modules.

The voltage difference has exceeded 50V for more than 2 minutes.
For example, parameter 14:109 [L0 DC BusVoltage] differs from parameter
14:209 [L1 DC BusVoltage] by more than 50V.
A peripheral device update time-out has happened with the main control board
during a firmware update.
Port number of attached device is the first two digits of the fault/alarm code.
A peripheral device update reset time-out has happened with the main control
board during a firmware update.
A peripheral device login with the main control board failed after firmware
update.
A peripheral device DPI error has occurred during a firmware update.

Port number of attached device is the first two digits of the fault/ alarm code.
Checksum failed for non-volatile data.

Action
Determine where the Auxiliary input function is assigned using parameter 0:115 [DI
Aux fault]. Verify that this assigned input is not open or reset.
Verify an I/O connection is not established to the drive. For example, a PLC is
communicating with the drive.
Normal operation when Emergency override is activated. Parameter 0:456

[EmergMode Status] displays the status of emergency override mode. To clear,
deactivate Emergency override mode.
Connect 24V DC auxiliary power to the control pod and resend the request for
energy pause. See the installation instructions, publication 750-IN100 for PowerFlex
755T or publication 750-IN119 for PowerFlex 755TS products, for terminals
location.
—
—
—
—
Determine why the Auto Restart function expired. Examine the fault queue for
which fault was unable to reset and troubleshoot that fault.
Verify adequate airflow and the ambient temperature is within specification. See
the technical data, publication 750-TD100 for PowerFlex 755T or 750-TD104 for
PowerFlex 755TS products.
Check whether the control pod fans are functioning properly.
Check whether the control pod fans are functioning properly.
Normal operation when parameters are defaulted.
—
—
Check the condition of cabinet air filters.
Verify that the ambient temperature is within specification. See the technical data,
publication 750-TD100 for PowerFlex 755T or 750-TD104 for PowerFlex 755TS
products.
publication 750-TD100 for PowerFlex 755T or 750-TD104 for PowerFlex 755TS
products.
Normal operation when parameters are defaulted.
See the event queue in Port 1

Check the human interface module (HIM) connections and cable for damage.
If the fault occurs when disconnecting the HIM, use the remove feature.
See the HIM user manual, publication 20HIM-UM001.
Add a common mode core on the output of the drive or, add a ferrite core to the
DPI cable.
Add a common mode core on the output of the drive or, add a ferrite core to the
DPI cable.
Verify that the backplane ports are free of debris and mounting screws are secured.
Reseat option card.
If problem persists, contact technical support
Verify that the backplane ports are free of debris and mounting screws are secured.
Reseat option card.
If problem persists, contact technical support
Verify that the backplane ports are free of debris and that mounting screws are
secure.
Reseat the option module.
If the problem persists, contact technical support.
Reset parameter defaults.

This fault occurs on power down but is checked for on power-up. If the power
down occurs too fast, this fault can occur.
If you are using an undersized auxiliary power supply and last power down was
from auxiliary power, this fault can occur.
Reload parameters.
Ensure the auxiliary power supply is properly sized. See the installation instructions,
publication 750-IN100 for PowerFlex 755T or publication 750-IN119 for PoweFlex
755TS products, for requirements.
If problem persists, replace main control board. See the hardware service manual,
publication 750-TG100 for PowerFlex 755T or publication 750-TG101 for PowerFlex
755TS products, for the replacement procedure.
Verify that the auxiliary power supply is sized correctly.

If problem persists, replace the main control board.
See the hardware service manual, publication 750-TG100 or publication 750-TG101
for PowerFlex 755TS products, for the replacement procedure.
Important: Predictive maintenance and runtime data on the main control board is
lost.
—
Cycle power.
If fault persists, replace the main control board.
See the hardware service manual, publication 750-TG100, for PowerFlex 755T or
publication 750-TG101 for PowerFlex 755TS products, for the replacement
procedure.
Cycle power.
If fault persists, replace the main control board.
See the hardware service manual, publication 750-TG100 for PowerFlex 755T or
procedure.
Replace the main control board.

procedure.
If a 24V DC auxiliary power supply is used for control power, confirm that the
power supply is sized for the drive before main control board replacement.
Cycle power to the product.

If this alarm persists, replace the main control board.
procedure.
—
Correct the digital Input configuration.
Determine where the DI Regen OK input function is assigned using parameter 0:116
[DI Regen OK]. Verify that this assigned input is not open or reset.
—
Verify the connection for the pod fan on products that have pod fans.
Verify the position of the bypass jumper on products that do not have pod fans.
Reseat or replace the pod fan or bypass jumper as needed. See the hardware
service manual, publication 750-TG100 for PowerFlex 755T or publication 750-
TG101 for PowerFlex 755TS products.
—
—
—
—
Install the Hardware Enable jumper on the main control board.

See the installation instructions, publication 750-IN100 for PowerFlex 755T or
publication 750-IN119 for PowerFlex 755TS products, for jumpers location and
configurations.
See the event queue or fault status for the safety option module.
If the fault persists, reseat the main control board.
Install the Safety jumper on the main control board.

Cycle power.
If you do not intend to use a safety module, install the safety jumper.
See the installation instructions, publication 750-IN100 for PowerFlex 755T or
publication 750-IN119 for PowerFlex 755TS products, for jumper locations and
configurations.
Remove the Safety jumper on the main control board.

Cycle power.
Cycle power.
If the fault persists, replace the main control board.
procedure.
Verify that the product configuration.

Cycle power.
If the fault persists:
procedure.
Replace any option modules.
See the option modules installation instructions, publication 750-IN111, for option
module installation details.
Verify the product configuration.
Cycle power.
procedure.
See the option module installation instructions, publication 750-IN111, for option
Verify configuration.
Cycle power.
procedure.
See the option modules installation instructions, publication 750-IN111, for option
Correct the port configuration.

See the option module installation instructions, Publication 750-IN111, for valid
port configurations.
A firmware update can be required to support certain option modules.




Acknowledge the new configuration by selecting ‘Fix’ from the HIM or from
software.
If a configuration change is not intended, power down and inspect the fiber
communication and connections to power peripherals (Mn power layer interface
board, DC precharge board, or TAM if installed).
Acknowledge the new configuration by selecting ‘Fix’ from the HIM or from
software.
If a configuration change is not intended, power down and inspect the fiber
communication and connections to power peripherals (Ln power layer interface
board, AC precharge board, and current sense board).
Install the correct power feedback board.

procedure.
—
Replace the input bay fans and reset the predictive maintenance function for them.
procedure.
Replace the control pod fans and reset the predictive maintenance function for
them.
procedure.
Replace the power bay roof fans and reset the predictive maintenance function for
them.
procedure.
Replace the wiring bay roof fans and reset the predictive maintenance function for
them.
procedure.
Replace the control bay roof fans and reset the predictive maintenance function for
them.
procedure.
Connect and configure a source for a stop command.

Review the installation and set bit 0 ‘Module Enbl’ in parameter 12:55 [Trq Accy
Mod Cfg] if Torque Accuracy module is needed for desired configuration.
Otherwise, set parameter 12:58 [TAM Not Cfg Actn] to 0 ‘Ignore’.
Cycle power to load the value.
Review the installation and clear bit 0 Module Enbl in parameter 12:55 [Trq Accy
Mod Cfg].
Cycle power to load the value.
Review the installation and parameter configuration. Remove the invalid data
source parameter or install the required option module.
This alarm can be cleared by changing parameter 0:101 [Digital In Cfg] to run edge
or by configuring a digital input signal for parameter 0:120 [DI M Run] or parameter
0:123 [DI L Run].
Cycle power and redownload parameters.

If fault persists, replace main control board.
procedure.

See hardware service manual, publication 750-TG100 for PowerFlex 755T or
procedure.

procedure.
Cycle power.
If the fault persists, replace main control board and/or fiber interface circuit board.
See hardware service manual, publication 750-TG100 for PowerFlex 755T or
procedure.
Verify that the connected capacitance is within specification. See the common bus
application techniques, publication DRIVES-AT005.
Clear fault and reattempt Precharge.
Cycle power.
Power down and examine the fiber transceiver circuit board edge connections on
to the fiber interface circuit board for damage, debris, or other contamination.
Reseat all fiber transceiver circuit boards.
Power down and check the hardware.
Cycle power.
If the fault persists, run a firmware update.
If the new configuration is desirable, follow the human interface module (HIM) or
Connected Components Workbench™ prompts to fix the product configuration.
If the new configuration is not desired, power down and examine the configuration.
Include the fiber-optic connections on the Fiber Interface Board (FIB).
Cycle power.
Power down and examine the fiber transceiver circuit board edge connections to
the fiber interface circuit board for damage, debris, or other contamination.
Reseat all fiber transceiver circuit boards.
Power down.
Examine the fiber-optic cable connections between the Mn power modules power
layer interface (PLI) circuit boards and the fiber interface circuit board for damage.
Verify that the Mn PLI fiber-optic cable is inserted into the correct socket on the
fiber interface circuit board.
See the installation instructions, publication 750-IN100, for information on fiber-
optic connections.
Power down.
Examine the fiber-optic cable connections between the Ln power modules power
layer interface (PLI) circuit boards and the fiber interface circuit board for damage.
Verify that the Ln PLI fiber-optic cable is inserted into the correct socket on the
fiber interface circuit board.
optic connections.
Power down.
Examine the fiber-optic cable connections between the LCL filter module current
sense circuit boards (CSB) and the Ln power modules power layer interface (PLI)
circuit boards for damage.
Verify that the CSB fiber-optic cable is inserted into the PDI socket on the Ln PLI
circuit boards.
optic connections.
Power down.
Examine the fiber-optic cable connections between the DC precharge modules and
the Mn power modules power layer interface (PLI) circuit boards for damage.
Verify that the DC precharge fiber-optic cable is inserted into the PDI socket on the
Mn PLI circuit boards.
optic cable connections.
Power down.
Examine the fiber-optic cable connections between the AC precharge module and
the fiber interface circuit board for damage.
Verify that the AC precharge fiber-optic cable is inserted into the correct socket on
the fiber interface circuit board.
optic cable connections.
Power down and examine the fiber-optic cable connections between the TAM and
the fiber interface circuit board for damage.
Verify that the TAM fiber-optic cable is inserted into the correct socket on the fiber
interface circuit board.
optic connections.
Examine the status indicators on the option cards for errors. Power down and check
backplane connections. Reseat option card if needed. Refer to the associated
manual of the option card for troubleshooting.
Power down and examine the placement of backplane option cards in the control
pod. Review the slot restrictions in the Installation Instructions.
Power down and examine the voltage class of the power peripherals: torque
accuracy module (TAM), AC precharge module (ACP), DC precharge module (DCP),
and power modules.
Power down and examine the power peripherals and the fiber-optic cable
connections on the fiber interface circuit board.
Power down and verify that the power mode plugs on the power layer interface
(PLI) circuit board are connected properly.
Contact technical support.
Cycle power.
Verify fiber-optic cable connections.
Update firmware.
Power down and verify current sense board (CSB) jumpers are set properly for each
channel.
Power down and verify that the LCL filter subframes match the converter
subframes and the correct filter size is connected to match the power layer
interface (PLI) board configuration.
Power down. Then correct the configuration.
Power down. Then correct the configuration.
Power down and verify fiber-optic cable connections.
Cycle power.
If the fault persists, replace power layer interface (PLI) circuit boards one by one.
procedure.
Power down and remove invalid safety option modules. Verify ATEX switches.
See the ATEX option module user manual, publication 750-UM003, for switch
settings.
Cycle power.
Power down and examine the fiber-optic connection on the fiber interface circuit
board to the torque accuracy module (TAM).
publication 750-TG101 for PowerFlex 755TS products, for information on the fiber
transceiver circuit board connections.
Power down and correct the fiber-optic cable connections.
Review the desired motor control mode.

Set parameter 0:65 [Pri MtrCtrl Mode] to the proper value.
Cycle power to load the control mode.
Review the desired application mode.

Set parameter 0:70 [Application Sel] to the proper value.
Review the desired embedded logic mode.

Set parameter 0:72 [Emb Logic Select] to the proper value.
Investigate the network architecture and network connections.
Normal operation if a PLC was set to Program mode.
Investigate the message command from the controller for errors.

Cycle power and verify fiber-optic cable connections and peripherals.
If this fault persists, replace main control board and/or peripherals.
procedure.
Review the desired secondary motor control mode.

Set parameter 0:67 [Sec MtrCtrl Mode] to the proper value.
Reconfigure one of the from-net datalink parameters to write to a different

parameter.
Review the desired velocity units. Set parameter 0:46 [Velocity Units] to the proper
value, and then cycle power to change the units. Review all parameters affected by
the velocity units as they are converted on power-up.
To maintain the current voltage class, change the value of parameter 0:33
[VoltageClass Cfg] to match the value of parameter 0:34 [VoltageClass Act].
To change the product to the voltage class configured in parameter 0:33
[VoltageClass Cfg], power cycle the product.
To maintain the current duty rating, change the value of parameter 0:35 [Duty
Rating Cfg] to match the value of parameter 0:36 [Duty Rating Act].
To change the product to the duty rating configured in parameter 0:35 [Duty Rating
Cfg], power cycle the product.
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Check status indicators.

Verify that all power peripherals are powered.
Power down and then check the fiber-optic communication connections.
This fault can be issued during some power down sequences.

Cycle power.
Cycle power.
Power down and then check the fiber-optic communication connection between
the fiber interface circuit board and M0 PLI for damage.
Replace the fiber-optic cable and/or fiber transceiver circuit board if needed.
procedure.
See the control pod fiber diagram on the Tables & Graphics tab.
procedure.
procedure.
procedure.
procedure.
procedure.
procedure.
procedure.
procedure.
procedure.
the fiber interface circuit board and L0 PLI for damage.
procedure.
procedure.
procedure.
procedure.
procedure.
procedure.
procedure.
procedure.
procedure.
procedure.
the fiber interface circuit board and ACP0 for damage.
procedure.
the fiber interface circuit board and TAM/ACP1 for damage.
procedure.
Cycle power.
If the fault persists, replace the main control board and/or the fiber interface circuit
board.
procedure.
Cycle power.
If the fault persists replace main control board.
procedure.
Check the condition of cabinet air filters and fans.

Verify that there is adequate airflow and the ambient temperature is within
specification. See the technical data, publication 750-TD100 for PowerFlex 755T or
publication 750-TD104 for PowerFlex 755TS products.

Verify that there is adequate airflow and the ambient temperature is within
specification. See the technical data, publication 750-TD100 for PowerFlex 755T or
publication 750-TD100 for PowerFlex 755T or publication 750-TD104 for PowerFlex
755TS products.
publication 750-TD100 for PowerFlex 755T or publication 750-TD104 for PowerFlex
755TS products.
procedure.
procedure.
procedure.
procedure.
procedure.
procedure.
procedure.
procedure.
procedure.
procedure.
procedure.
procedure.
procedure.
procedure.
procedure.
procedure.
Replace the fiber cable and/or fiber transceiver if needed.
procedure.
procedure.
procedure.
the fiber interface circuit board and ACP0 for damage.
procedure.
the fiber interface circuit board and TAM/ACP1 for damage.
procedure.
Verify that the U phase current is balanced between all parallel inverters by
monitoring parameter Mn CurrentFdbk U where x is the module number. Example
parameter 12:105 [M0 CurrentFdbk U] and 12:205 [M1 Current Fdbk U].
Troubleshoot power modules based on parameter investigation.
Verify that the V phase current is balanced between all parallel inverters by
monitoring parameter Mn CurrentFdbk V where n is the module number. Example
parameter 12:106 [M0 CurrentFdbk V] and 12:206 [M1 Current Fdbk V].
Verify that the W phase current is balanced between all parallel inverters by
monitoring parameter Mn CurrentFdbk W where n is the module number. Example
parameter 12:107 [M0 CurrentFdbk W] and 12:207 [M1 Current Fdbk W].
Check cabinet filters, heatsink fans, intake air temperatures Verify ambient
temperature is uniform throughout all power bays.
Verify adequate airflow and the baffles that help prevent recirculation of heated
air.
air.
air.
Measure DC Bus of the power modules from the local test points. Power Down and
then check DC link fuses and DC bus harnesses of power modules with mismatched
DC Bus voltage measurements.
If DC Bus voltage measurement differs from parameter value, inspect power
module connections and PIB.
Verify that the R phase current is balanced between all parallel converters by
monitoring parameter Ln CurrentFdbk R where x is the module number. Example
parameter 14:105 [L0 CurrentFdbk R] and 14:205 [L1 Current Fdbk R]. Troubleshoot
power modules based on parameter investigation.
Verify that the S phase current is balanced between all parallel converters by
monitoring parameter Ln CurrentFdbk S where n is the module number. Example
parameter 14:105 [L0 CurrentFdbk S] and 14:205 [L1 Current Fdbk S]. Troubleshoot
Verify that the T phase current is balanced between all parallel converters by
monitoring parameter Ln CurrentFdbk T where n is the module number. Example
parameter 14:105 [L0 CurrentFdbk T] and 14:205 [L1 Current Fdbk T]. Troubleshoot
air.
air.
air.
Measure DC Bus of the power modules from the local test points. Power Down and
then check DC link fuses and DC bus harnesses of Ln power modules with
mismatched DC Bus voltage measurements.
If DC Bus voltage measurement differs from parameter value, inspect Ln power
module connections and PIB.
Power down and verify peripheral connections are secure. Rerun device firmware
update.
Cycle power.
If the fault persists, replace the fiber-optic interface board.
procedure.
Fault Action Configuration Parameter
Coast (Motor Side Inverter) 0:115 [DI Aux Fault]

Stop (Line Side Converter)
Additional Fault Action
Fault opens main circuit breaker: No
Fault can automatically reset: Yes
Emergency override response: 0:455 [Emerg Prot
OVRD] bit 4 ‘PERIF Flts’
— —
Fault can automatically reset: No
Emergency override response: Cannot override this
fault.
— —
— —
Coast (Motor Side Inverter) —

fault.
— —
— —
— —
— —
Coast (Motor Side Inverter) 0:60 [Auto Retry Fault] Bit 0
Stop (Line Side Converter) 0:61 [Auto Rstrt Tries]
Additional Fault Action 0:62 [Auto Rstrt Delay]
fault.
— —

OVRD] bit 7 ‘Board Faults’
— —
Fault opens main circuit breaker: N/A
fault.
— —
— —
— —
— —
— —
fault.

OVRD] bit 10 ‘Pt1...3 Flts’


OVRD] bit 11 ‘Port 4 Flts’


Configurable 0:204 [DPI Pt1 Flt Actn]







Fault opens main circuit breaker: Yes
fault.
— —
— —
— —
— —
— —
— —
— —

fault.
— —
— —
— —
— —
Coast (Motor Side Inverter) 0:116 [DI Regen OK]

Emergency override response: Ignore
— —
— —
— —
— —
— —
— —
— —
— 0:480 [MixedCorProtActn]

fault.
fault.

fault.

fault.

fault.

fault.
fault.

fault.
— —
— —
— —
— —
— —
— —
— —

fault.
— —
— —
— —
— —
— —
— —

— —
— —
— —
Configurable 0:1921 [NonStdDataActn]

— —


fault.

fault.
fault.

OVRD] bit 1 ‘LS Pwr Flts’

fault.
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —

fault.
fault.

fault.

fault.

fault.
— —
— —

fault.
fault.

fault.

fault.

fault.

fault.
— —
— —
fault.

fault.
— —
— —
— —
Configurable 0:360 [Comm Flt Action]

OVRD] bit 5 ‘ENET Flts’
Configurable 0:361 [Idle Flt Action]

Configurable 0:363 [Msg Flt Action]

fault.
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —

fault.

fault.
fault.

fault.

fault.

fault.

fault.
fault.

fault.

fault.

fault.

fault.
fault.

fault.

fault.

fault.

fault.
fault.

fault.

fault.

fault.

fault.
fault.

fault.

fault.

fault.

fault.
fault.
— —

fault.
— —

fault.

fault.
fault.

fault.

fault.

fault.

fault.
fault.

fault.

fault.

fault.

fault.
fault.

fault.

fault.

fault.

fault.
fault.

fault.

fault.

fault.

fault.
fault.
— —
— —
— —
— —
— —
— —

fault.
— —
— —
— —
— —
— —
— —
Stop (Line Side Converter) —

fault.
— —
— —
— —
— —

fault.
Configurable Action
—
—
—
—
—
—
—
—
—
—
—
—
—
Fault
Stop
Zero Data
Hold Last
Send Flt Cfg
Fault
Stop
Zero Data
Hold Last
Send Flt Cfg
Fault
Stop
Zero Data
Hold Last
Send Flt Cfg
—
—
—
—
—
—
—
—
—
—
—
—
Ignore
Alarm
—
—
—
—
—
—
—
Ignore
Alarm
Ignore
Alarm
Ignore
Alarm
Ignore
Alarm
Ignore
Alarm
—
—
Ignore
Alarm
—
—
—
—
—
—
—
—
—
—
Fault
Stop
Zero Data
Hold Last
Send Flt Cfg
Fault
Stop
Zero Data
Hold Last
Send Flt Cfg
Fault
Stop
Zero Data
Hold Last
Send Flt Cfg
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Configurable 9002 DLX IO Cfg Invld DLX IO Configuration Invalid
Resettable Fault 9003 DLX Checksum DeviceLogix Checksum
Resettable Fault 9004 EmbLogic Adapter Embedded Logic Adapter
Alarm 2 9012 TP MtrCtrl Mode Torque Prove Motor Control Mode

Conflict
Alarm 2 9013 Torq Prove Cflct Torque Prove Conflict

Minor Fault 9014 TP Encls Config Torque Prove Encoderless
Configuration
Minor Fault 9015 TP Sec Mtr Ctrl Torque Prove Secondary Motor
Control Conflict
Alarm 2 9016 PID MtrCtrl Port PID Motor Control Port Configuration
Alarm 2 9048 Sleep Config Sleep Configuration
Alarm 1 9049 Waking Waking
Alarm 2 9050 SleepMtrCtrl Cfg Sleep/Wake Motor Control

Configuration Error
Configurable 9086 OW TrqLvlTimeout Oil Well Torque Level Timeout
Alarm 1 9087 OW Torq High Oil Well Torque High
Alarm 1 9088 Pump Off Pump Off

Alarm 2 9089 PumpJack SecMtr PumpJack Secondary MotorControl
Conflict
Configurable 9090 OW Torq Low Oil Well Torque Low
Alarm 2 9091 OW MtrCtrl Cflct Oil Well Motor Control Configuration

Fault
One or more parameters used by the DeviceLogix program do not exist on

the port specified in the program mapping file.
DeviceLogix storage checksum failed.

Data are set to default values.
The DeviceLogix adapter has a fault.
The torque proving application has been selected with an unsupported

motor control mode.
The product cannot run in this configuration.
When parameter 9:50 [Trq Prove Cfg] bit 0 ‘TP Enable’ is set, this alarm is
set when any of the following occurs:
- Parameter 10:34 [PsnVelTrq Actv] states Zero Torque or Torque mode
- Parameter 0:66 [Pri MtrCtrl Act] is not set to Induction FV
- The active stop mode selected by parameters 10:110 [Mtr Stop Mode A]
and 10:111 [Mtr Stop Mode B] is not set to Ramp
- Parameter 10:256 [OutPhaseLossActn] is not set to FltCoastStop
- Parameter 10:431 [FluxUpTm C/U Sel] is set to ‘User Entered’ and
parameter 10:433 [u FluxUpTime] is 0.03 seconds or less
- Parameter 9:50 [Trq Prove Cfg] bit 1 ‘Encoderless’ is not set and
parameters 10:1000 [Pri Vel Fb Sel] and/or 10:1013 [PReg Fb Sel] is set to
Open Loop, Simulation Feedback, or an invalid feedback device
- Parameter 9:50 [Trq Prove Cfg] bit 1 ‘Encoderless’ is set and parameter
10:1000 [Pri Vel Fb Sel] is set to a feedback device
- The feedback device is set for A channel only and/or Single Ended
- The feedback loss response configuration for the feedback device is not
set to FltCoastStop
Encoderless TorqProve has been enabled but you have not read and
understood application concerns of encoderless operation.
You have not read and understood the application concerns related to the
configuration of the secondary motor control port when the torque prove
function is enabled in the primary motor control port.
Parameter 9:25 [PID Ref Sel], 9:35 [PID Fdbk Sel], 9:42 [PID FBLoss SpSel],
or 9:43 [PID FBLoss TqSel] is configured for a data source that resides in a
motor control port that is not selected in parameter 9:16 [PID Mtr Ctrl
Sel].
The sleep/wake application is incorrectly configured. Possible causes

include:
- Parameter 9:90 [Sleep Wake Mode] is set to 1 ‘Direct’, and the value of
parameter 9:94 [Wake Level] is less than or equal to the value of
parameter 9:92 [Sleep Level].
- Parameter 9:90 [Sleep Wake Mode] is set to 2 ‘Invert’, and the value of
parameter 9:92 [Sleep Level] is less than or equal to the value of
parameter 9:94 [Wake Level].
- A digital input signal is not configured for at least one of the following
parameters: 0:103 [DI M Enable], 0:108 [DI M Stop], or 0:120 [DI M Run]. If
parameter 0:120 [DI M Run] is configured, then parameter 0:101 [Digital In
Cfg] must be set to 0 ‘Run Edge’.
The Wake timer is counting toward a value (parameter 9:95 [Wake Time])
that starts the drive.
A motor control mode is configured for the secondary motor control port
(port 11) while the sleep/wake feature is enabled.
The product only supports sleep/wake as a standalone application with
the primary motor control port (port 10).
Oil well high torque level alarm has been active for a set time in parameter
9:152 [TorqAlmTimeOutHi].
Oil well torque has exceeded the threshold configured in parameter 9:151
[Torq Thresh High] for a set time in parameter 9:150 [TorqAlarm Dwell].
Pump Off condition has been detected.

The pump jack application is configured concurrently with secondary
motor control port (port 11). The product only supports the pump jack
application with the primary motor control port (port 10).
Oil well torque has fallen below the threshold configured in parameter
9:154 [Torq Thresh Low] for a time in parameter 9:161
[TorqAlmTimeOutLo].
The oil well application is enabled with a non-flux vector control mode
selected. The oil well application is only supported with flux vector control
in the primary motor control port.
Action
Install option modules in the slots expected by the DeviceLogix program or update
the DeviceLogix program to accommodate the existing option module
configuration.
To clear this alarm, change the value of parameter 0:65 [Pri MtrCtrl Mode] to an
induction motor control mode or change the value of parameter 0:70 [Application
Sel] to a value other than torque proving.
Correct the parameter configuration.

Read the ‘Attention’ statement in the programming manual publication 750-PM101
relating to the use of encoderless TorqProve.
Read the ‘Attention’ statement in the programming manual publication 750-PM101

relating to the use of TorqProve while the secondary motor control port is
configured.
Change the value of parameter 9:16 [PID Mtr Ctrl Sel] or reconfigure parameter
9:25 [PID Ref Sel], 9:35 [PID Fdbk Sel], 9:42 [PID FBLoss SpSel], and 9:43 [PID FBLoss
TqSel] to eliminate selection of data sources in the motor control port that is not
selected in parameter 9:16 [PID Mtr Ctrl Sel].
Correct the parameter configuration.
Normal operation that indicates that the drive is waking and is about to start.
Set parameter 0:67 [Sec MtrCtrl Mode] to 0 ‘None’ and power cycle or set
parameter 9:90 [Sleep Wake Mode] to 0 ‘Disabled’.
Indicates that the oil well high torque level alarm has timed out.
Investigate the cause of high torque on the motor.
Indicates that the oil well high torque level is in alarm.

Investigate the cause of high torque on the motor.
Normal operation that indicates that the drive has detected a pump off condition.
Disable the pump jack application in parameter 9:100 [OilWell Pump Cfg] or set
parameter 0:67 [Sec MtrCtrl Mode] to 0 ‘None’.
Indicates that the oil well low torque level is in alarm.

Investigate the cause of low torque on the motor.
Change parameter 0:65 [Pri MtrCtrl Mode] to a flux vector control mode and power
cycle the product, or change parameter 9:100 [OilWell Pump Cfg] to disable.
Configurable 9:1003 [DLX InvldIO Actn]

OVRD] bit 6 ‘DevLgx Flts’


— —
— —
Coast —
OVRD] bit 9 ‘TorqPrv Flts’
Coast —
OVRD] bit 9 ‘TorqPrv Flts’
— —
— —
Fault can automatically reset: N/A
fault.
— —
— —
Configurable 9:148 [TorqAlarm Action]

Additional Fault Action 9:152 [TorqAlmTimeOutHi]
Fault opens main circuit breaker: No 9:153 [TorqAlmTOActnHi]
OVRD] bit 2 ‘MS Ctrl Flts’
— 9:150 [TorqAlarm Dwell]

9:151 [Torq Thresh High]
— —
— —
fault.
Configurable 9:154 [Torq Thresh Low]

Additional Fault Action 9:161 [TorqAlmTimeOutLo]
Fault opens main circuit breaker: No 9:162 [TorqAlmTOActnLo]
— —
fault.
Configurable Action
Type 1 Alarm
Fault
—
—
Ignore
Preset Spd1
—
—
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
—
Configurable 10001 Power Loss Power Loss

11001
Alarm 1 10002 Mtr Ovrld Alarm Motor Overload Alarm

11002
Configurable 10003 Motor Overload Motor Overload

11003
Configurable 10004 Load Loss Load Loss

11004
Configurable 10005 Input Phase Loss Input Phase Loss

11005
Resettable Fault 10007 TorqPrv Spd Band Torque Prove Speed Band
11007
Configurable 10008 Output PhaseLoss Output Phase Loss
11008
Configurable 10009 Decel Inhibit Decel Inhibit

11009
Resettable Fault 10010 OverSpeed Limit OverSpeed Limit
11010
Alarm 1 10011 BrakeSlippedActv Brake Slipped - Drive Active

11011
Alarm 2 10012 BrakeSlippedStop Brake Slipped - Drive Stopped

11012
Alarm 2 10014 Invld DC Bus Ref Invalid DC Bus Reference

11014
Non-Resettable 10015 OverFreq Limit Over Frequency Limit

Fault 11015
Resettable Fault 10016 Phase U to Grnd Phase U to Ground

11016
Resettable Fault 10017 Phase V to Grnd Phase V to Ground

11017
Resettable Fault 10018 Phase W to Grnd Phase W to Ground
11018
Resettable Fault 10019 Phase UV Short Phase UV Short

11019
Resettable Fault 10020 Phase VW Short Phase VW Short

11020
Resettable Fault 10021 Phase WU Short Phase WU Short

11021
Resettable Fault 10022 Phase UNegToGrnd Phase U Negative To Ground

11022
Resettable Fault 10023 Phase VNegToGrnd Phase V Negative To Ground

11023
Resettable Fault 10024 Phase WNegToGrnd Phase W Negative To Ground

11024
Configurable 10025 Shear Pin 1 Shear Pin 1 Value Exceeded
11025
Configurable 10026 Shear Pin 2 Shear Pin 2 Value Exceeded

11026
Alarm 1 10027 Drive OverLoad Drive OverLoad

11027
Resettable Fault 10028 Drive OverLoad Drive OverLoad
11028
Resettable Fault 10029 Stator Res Range Stator Resistance Range

11029
Resettable Fault 10030 FluxAmpsRef Rang Flux Amps Reference Range

11030
Resettable Fault 10031 Excessive Load Excessive Load

11031
Resettable Fault 10032 AutoTune Aborted Auto Tune Aborted

11032
Resettable Fault 10033 Leakage L Range Leakage Inductance Range
11033
Resettable Fault 10034 StcOffstPulsFail PM Static Offset Pulse Test Failure

11034
Resettable Fault 10035 StcOffstRtrFail PM Static Offset Rotor Test Failure

11035
Resettable Fault 10038 Auto Tach Switch Auto Tach Switch

11038
Alarm 1 10039 Start On PowerUp Start On PowerUp

11039
Configurable 10040 Ext Prechrg Err External Precharge Error

11040
Alarm 2 10041 PrechargeOpenAlm Precharge Open Alarm

11041
Resettable Fault 10042 PrechargeOpenFlt Precharge Open Fault

11042
Resettable Fault 10043 Autn Enc Angle Autotune Encoder Angle
11043
Resettable Fault 10044 Autn Vel Rstrct Autotune Velocity Restricted

11044
Resettable Fault 10045 Autotune CurReg Autotune Current Regulator

11045
Resettable Fault 10046 Autotune Travel Autotune Travel

11046
Resettable Fault 10047 No Stop Source No Stop Source

11047
Configurable 10048 Accel Limit Acceleration Limited

11048
Configurable 10049 Decel Limit Deceleration Limited
11049
Alarm 1 10050 PWM Freq Reduced PWM Frequency Reduced
11050
Alarm 1 10051 CurLimit Reduced Current Limit Reduced
11051
Resettable Fault 10053 Pos Over Travel Positive Over Travel

11053
Resettable Fault 10054 Neg Over Travel Negative Over Travel

11054
Non-Resettable 10055 Travel Lim Cflct Travel Limit Conflict

Fault 11055
Alarm 1 10056 Profiling Active Profiling Active

11056
Alarm 1 10057 Homing Active Homing Active

11057
Alarm 1 10058 Home Not Set Home Not Set

11058
Alarm 2 10059 Invld Homing Cfg Invalid Homing Configuration
11059
Alarm 2 10059 Invld Homing Cfg Invalid Homing Configuration
11059
Resettable Fault 10060 Fwd End Limit Forward End Limit

11060
Resettable Fault 10061 Rev End Limit Reverse End Limit

11061
Alarm 2 10063 Freq Conflict Frequency Conflict

11063
Alarm 2 10064 VHz Neg Slope VHz Negative Slope

11064
Alarm 2 10065 VHz Boost Limit VHz Boost Limit
11065
Alarm 2 10066 VHz Curve Incomp VHz Curve Incompatible

11066
Alarm 1 10067 DynBrake OvrTemp Dynamic Brake Resistor Over

11067 Temperature
Alarm 1 10068 MVFB Thrshld Exd MVFB Threshold Exceeded
11068
Resettable Fault 10069 SyRSpdEstErr Sync Rel Speed Estimate Error

11069
Alarm 2 10070 Fwd Spd Lim Cfg Forward Speed Limit Configuration
11070
Alarm 2 10071 Rev Spd Lim Cfg Reverse Speed Limit Configuration
11071
Alarm 2 10072 PM Offset Cnflct Permanent Magnet Offset Conflict

11072
Resettable Fault 10073 IPMSpdEstErr Internal Permanent Magnet Speed
11073 Estimate Error
Resettable Fault 10075 DynOffstFail PM Dynamic Offset Test Failure

11075
Configurable 10076 Excess Psn Err Excessive Position Error

11076
Configurable 10080 M Ground Warning Inverter Ground Warning

11080
Configurable 10081 HRG Gnd Warn High Resistance Ground Current
11081
Configurable 10082 HRG Gnd Warn Lcl High Resistance Ground Current
11082 Local
Alarm 1 10083 Fdbk Data Late Control Feedback Data Arrived Late
11083
Alarm 1 10084 PWM Data Late PWM Data Arrived Late

11084
Resettable Fault 10085 IPM OverCurrent Internal Permanent Magnet Over
11085 Current
Configurable 10086 PTP Solver Fail Point to Point Plan Solver Failure
11086
Configurable 10087 VRef Solver Fail Velocity Reference Solver Failure

11087
Resettable Fault 10092 SW OverCurrent Software Over Current
11092
Resettable Fault 10093 HW OverCurrent Hardware Over Current

11093
Resettable Fault 10094 Heatsink OvrTemp Heatsink Over Temperature

11094
Resettable Fault 10095 125us Task Ovr 125us Task Overrun

11095

11096
Resettable Fault 10097 1ms Task Ovr 1ms Task Overrun
11097

11098

11099

11100
Resettable Fault 10101 CntrlTask Wtchdg Control Task Watchdog

11101
Resettable Fault 10102 SystmTask Wtchdg System Task Watchdog

11102
Resettable Fault 10103 1ms Task Wtchdg 1ms Task Watchdog

11103
11104

11105
Configurable 10106 UnderVoltage Under Voltage

11106
Resettable Fault 10107 OverVoltage Over Voltage

11107
Resettable Fault 10109 HeatSinkUnderTmp Heatsink Under Temperature

11109
Resettable Fault 10110 Autotune Inertia Autotune Inertia Out of Range

11110
Non-Resettable 10111 Inv App No Strt Inverter Application Not Start

Fault 11111
Resettable Fault 10112 InvalidLoadRatio Invalid Load Ratio
11112
Alarm 2 10113 SlipInvalidRange Invalid Slip Range

11113
Resettable Fault 10114 Jnt OverTemp Flt Junction OverTemp Fault

11114
Alarm 2 10115 Odd Motor Poles Odd Number of Motor Poles

11115 Configured
Resettable Fault 10118 Ld00 Fail D-Axis Inductance at 0 Pct

11118 OutOfRange
Resettable Fault 10119 Ld100 Fail D-Axis Inductance at 100 Pct

11119 OutOfRange
Resettable Fault 10120 Lq Fail Q-Axis Inductance Out of Range

11120
Alarm 1 10121 ChgPmpProtActive Charge Pump Protection Active
11121
Alarm 2 10122 SyR OpenLoop PWM Synchronous Reluctance Open Loop

11122 PWM
Event 10129 Pred Maint Reset Predictive Maintenance Reset

11129
Event 10130 MtrSide Started Motor Side PWM Started
11130
Event 10131 MtrSide Stopped Motor Side PWM Stopped
11131
Alarm 2 10132 InvldAutnTestCfg Invalid Autotune Test Configuration
11132
Configurable 10177 Mtr Brng Life Motor Bearing Life

11177
Configurable 10178 Mtr Lube Life Motor Lubrication Life
11178
Configurable 10179 Mch Brng Life Machine Bearing Life
11179
Configurable 10180 Mch Lube Life Machine Lubrication Life
11180
Fault
The DC bus voltage remained below the power loss level for longer than
power loss time.
See parameters 10:272 [Pwr Loss A Level], 10:273 [Pwr Loss A Time],
10:276 [Pwr Loss B Level], and 10:277 [Pwr Loss B Time].
Value of parameter 10:207 [Mtr OL Counts] exceeds the value of

parameter 10:202 [Mtr OL Alm Level].
See parameters 10:3 [Output Current], 10:401 [Motor NP Amps, 10:203
[Mtr OL Factor], and/or 10:204 [Mtr OL Hertz].
An internal electronic motor overload trip has occurred.

See parameters 10:3 [Output Current], 10:401 [Motor NP Amps, 10:203
[Mtr OL Factor], and/or 10:204 [Mtr OL Hertz].
The output torque current is below the value that is programmed in

parameter 10:251 [Load Loss Level] for a time period greater than the time
programmed in parameter 10:252 [Load Loss Time].
The input phase loss function has detected an excessive DC bus ripple.
Possible causes include an input phase loss on the incoming AC power at
the line side converter, cyclic loading, or speed loop tuning.
Spurious trips can occur when other conditions excite the second
harmonic in DC bus ripple on the DC bus.
See parameters 10:289 [InPhase LossActn] and 10:290 [InPhase Loss Lvl].
The difference between parameter 10:1914 [VRef Commanded] and

parameter 10:1044 [Motor Vel Fb] has exceeded the level in parameter
9:54 [Speed Dev Band] for a time period greater than the time
programmed in parameter 9:55 [SpdBand Intgrtr].
Current was lost or remained below the threshold set in parameter
10:257 [Out PhaseLossLvl] for 1 second in one or more phases.
Decrease the threshold to make the drive less sensitive to trip.
This adjustment is necessary when the motor is smaller than the drive
rating.
If TorqProve™ is active, the current was lost or remained below a
threshold for 5 ms.
The phases are checked at start to deliver torque to the load.
If the drive is faulting on start, increase parameter 10:433 [u FluxUpTime].
If TorqProve is active, and the brake is slipping, this fault occurs.
When TorqProve is used, before the signal to the brake is applied to
release it, the flux up time is used to check the three phases.
The angle is adjusted to deliver current through all three phases.
If the motor moves during this test, the brake is not holding and a phase
loss can occur.
If TorqProve is active, and no brake is present, this fault occurs.
Check for an open output contactor.
The drive is not following the commanded deceleration ramp because it is

attempting to limit DC bus voltage.
When using non-vector (scalar) control modes on high inertia loads, set
parameter 10:490 [u Slip RPM atFLA] to 0.
Motor speed has exceeded the limit set by parameter 10:1904 [Overspeed
Limit].
For forward motor rotation, this limit is parameter 10:1898 [Vel Limit Pos]
+ parameter 10:1904 [Overspeed Limit].
For reverse motor rotation, this limit is parameter 10:1899 [Vel Limit Neg]
- parameter 10:1904 [Overspeed Limit].
Parameter 10:1042 [Vel Fb Active] determines the motor operating speed.
For TorqProve only.

The encoder movement has exceeded the level in parameter 9:63 [Brk Slip
Thresh] after the brake was set and the brake slip maneuver is controlling
the drive (the drive is active).
Or
The safety enable input or safety enable input is low. Parameter 9:50 [Trq
Prove Cfg] bit 10 ‘BrkSlpFltCfg’ provides an option to inhibit condition
occurrence when enable input or safety enable input is low.
For TorqProve only. The encoder movement has exceeded the level in
parameter 9:63 [Brk Slip Thresh] after the brake was set and the brake slip
maneuver is finished (drive is stopped).
You must cycle power to clear this alarm.
Parameter 10:118 [Bus Reg Lvl Cfg] is set to 2 ‘LineSideRef’ for a common
bus inverter (CBI).
There is no line side reference for a CBI
Output frequency is greater than or equal to 590 Hz or less than or equal

to -590 Hz.
A phase to ground fault has been detected between the drive and motor
in this phase.
in this phase.
in this phase.
Excessive current has been detected between these two output terminals.
in this phase.
in this phase.
in this phase.
The Shear Pin function has tripped on first pin.
Motor current has exceeded the value in parameter 10:243 [Shear Pin1
Level].
The Shear Pin function has tripped on second pin.

Motor current has exceeded the value in parameter 10:246 [Shear Pin2
Level].
Parameter 10:357 [Drive OL Count] has exceeded 50% but is less than
100%.
Parameter 10:357 [Drive OL Count] has exceeded 100%.
Possible causes include loads that require too much current and power,
improper derating for temperature and altitude, and obstructed airflow.
Parameter 10:910 [Autotune] is set to 2 ‘Static MtrID’ or 3 ‘Rotate MtrID’

and the value for stator resistance in parameter 10:512 [u IM Stator Res]
measured by the Autotune function is not in the range of acceptable
values.

and the value for flux amps in parameter 10:518 [u Flux Cur Ref] measured
by the Autotune function exceeds the value that is programmed in
parameter 10:401 [Motor NP Amps].
The motor did not come up to speed in the allotted time during Autotune.
The Autotune function was interrupted. This interruption was the result of
manual cancellation or a fault.
and the voltage that was measured for motor inductive impedance
exceeds 25% of the value of parameter 10:400 [Motor NP Volts].
PM Pulse Test failed due to IOC overcurrent or pulse test time determined
was larger than the maximum allowed pulse test time.
PM Rotor position not found during the static offset test.
Both the primary feedback and alternate feedback devices have failed.
When parameter 10:50 [Start At PowerUp] is enabled, an alarm is set for

the time programmed in parameter 10:52 [PowerUp Delay].
The seal contact on the external precharge contactor has opened as

signaled by parameter 0:191 [DI Prchrg Seal].
The internal precharge-circuity-bypass relay (for drives) or main contactor

(for CBIs) was commanded to open while the drive was stopped (PWM
was not active) due to low DC bus voltage.
The internal precharge-circuity-bypass relay (for drives) or main contactor

(for CBIs) was commanded to open while the drive was running (PWM was
active) due to low DC bus voltage. The internal fault latch is automatically
cleared when PWM is disabled.
The autotune failed to calculate Parameter 10:521 [u EncLs AngCmp]
within range.
This can only occur for encoderlesss systems in Induction Flux Vector
mode.
Velocity Command is too low (< 25% base speed) to complete the inertia
test.
This condition is applicable to induction and permanent magnet motors.
Calculated value for the current regulator integral gain is out of range.
During an Inertia Test, the position limit value in parameter 10:911

[Autotune Psn Lim] did not allow the drive to reach a suitable velocity.
The last source for a Stop Command has been removed.
The inverter cannot achieve the configured acceleration time due to

current limiting.
The inverter cannot achieve the configured deceleration time due to
limiting imposed by the bus voltage regulator.
The thermal manager function has reduced the PWM frequency from the
value set in parameter 10:425 [PWM Frequency] due to excessive IGBT
junction temperatures.
See parameter 10:220 [Drive OL Mode].
The current limit value has been reduced from the value set in [Current
Limit n] due to excessive IGBT junction temperatures or parameter 10:357
[Drive OL Count] = 95%.
See parameter 10:220 [Drive OL Mode].
The system has exceeded the Positive Overtravel Limit.

The switch that feeds the digital input that is selected in parameter 0:184
[DI PHw OvrTrvl] has opened.
After the fault is cleared, the drive operates normally.
The system has exceeded the Negative Overtravel Limit.

The switch that feeds the digital input that is selected in parameter 0:185
[DI NHw OvrTrvl] has opened.
After the fault is cleared, the drive operates normally.
Travel limits are in conflict.

Both the forward and reverse travel limits indicate that they are
simultaneously active.
The travel limit digital inputs are meant to be connected to normally
closed switch contacts.
The digital input status reads an off (0 = False) bit status when the
machine is on limit and the switch contact opens.
A possible cause for this condition is loss of common power to both the
forward and reverse travel limit switches.
The Profile/Indexer is active.
The Homing function is active.
The Home position was not set before profile operation in absolute mode.
The homing configuration is invalid because both a digital input and a hard
stop are configured as inputs to detect the homing event.
The homing configuration is invalid for one of the following reasons:
- Both a digital input and a hard stop are configured as inputs to detect the
homing event.
- A homing marker is configured and either the feedback source that is
configured for positon regulation does not support a Z channel or the Z
channel is not enabled for the feedback source.
The selected digital input for one of the end limit switches, parameter
0:180 [DI FwdEndLimit] or 0:182 [DI RevEndLimit], has detected a falling
edge and parameter 10:34 [PsnVelTrq Actv] is not set to 1 ‘Speed Reg’.
The selected digital input for one of the end limit switches, parameter
0:180 [DI FwdEndLimit] or 0:182 [DI RevEndLimit], has detected a falling
edge and parameter 10:34 [PsnVelTrq Actv] is not set to 1 ‘Speed Reg’.
The values of parameters 10:1898 [Vel Limit Pos] and 10:1899 [Vel Limit
Neg] are in conflict with the value of parameter 10:484 [Break Frequency].
The V/Hz curve segment caused a negative V/Hz slope.
Indication that one of the two following conditions exists. Parameters

10:480 [Start Acc Boost] and 10:481 [Run Boost] are greater than
parameter 10:400 [Motor NP Volts] x 0.25 when parameter 10:486 [VHz
Curve] = 0 ‘Custom V/Hz’.
Parameter 10:481 [Run Boost] is greater than parameter 10:400 [Motor
NP Volts] x 0.25 when parameter 10:486 [VHz Curve] = 1 ‘Fan/Pump’.
Parameter 0:65 [Pri MtrCtrl Mode] or 0:67 [Sec MtrCtrl Mode] is set to
permanent magnet V/Hz and parameter 10:486 [VHz Curve] is set to 1
‘fan/pump’.
The dynamic brake resistor has exceeded its maximum operating

temperature.
The offset value of one or both channels of the torque accuracy module
(TAM) has exceeded the threshold level set by parameter 12:57 [OfstEvent
Thresh].
The speed estimator failed to track the high-speed angle and has lost the
field orientation of a synchronous reluctance motor. This condition only
applies to encoderless flux vector control.
The forward speed reference is out of range.
The reverse speed reference is out of range.
Both 10:580 [PM Config] bit 0 ‘AutoOfstTest’ and bit 1 ‘StaticTestEn’ are
set. Select only one.
The speed estimator failed to track the high-speed angle and has lost the
field orientation of an interior permanent magnet motor.
This condition only applies to encoderless flux vector control.
PM Dynamic Offset test failed due to interruption of the test before

completion or the motor movement failed to reach the proper amount of
rotation during the test.
The test is rescheduled when this fault occurs.
The absolute value of the position control loop error in parameter 10:1750
[Position Error] has exceeded the position error tolerance that is
configured in parameter 10:1773 [PsnErrTolerance] for a time that is
greater than or equal to the time that is configured in parameter 10:1774
[PsnErrTime].
The calculated ground current has exceeded the ground warning level for
5 seconds or longer. U,V, and W instantaneous phase currents sum to a
value greater than parameter 0:421 [M Gnd Warn Lvl].
The high-resistance ground (HRG) ground fault detection function has
detected ground current that exceeds the level in parameter 0:426 [HRG
GF Thresh].
The likely source of the high-resistance ground (HRG) ground current

condition is this drive.
The Control Feedback data arrived to the main control board late from the
power layer interface (PLI) circuit board and fiber interface circuit board.
PWM data arrived late from ICB

The PWM data arrived late from the main control board.
The current magnitude has exceeded the trip level set by parameter
10:698 [IPM Max Cur].
With parameter 10:931 [Ref Move Type] configured for 1 ‘SineSquared’, 2

‘Poly5’, or 3 ‘Cubic’, the position reference trajectory solver was unable to
find a solution based on the input constraints and target position
provided. Parameter 10:1410 [PTP Move Status], bit 4 ‘Move Failed’ is set
to 1.
With parameter 10:931 [Ref Move Type] configured for 1 ‘SineSquared’, 2

‘Poly5’, or 3 ‘Cubic’, the velocity reference trajectory solver was unable to
find a solution based on the input constraints and target velocity provided.
Parameter 10:1938 [VRef Move Status], bit 4 ‘Move Failed’ is set to 1.
Motor side inverter current has exceeded the 1 ms current rating.
This rating is greater than the current rating for 3 seconds and less than
the hardware overcurrent fault level. It is typically 200…250% of the drive
continuous rating.
Output current has exceeded the rating for the product.

Possible causes include short circuits in the motor and motor wiring.
The heatsink temperature has exceeded 100% of the drive temperature.

Heatsink over temperature occurs between 115…120 °C. The exact value is
stored in drive firmware.
See parameter 10:362 [Heatsink Temp Pct] and/or 10:363 [Heatsink
Temp].
The 125-microsecond task has overrun the allotted time.

The 1-millisecond task has overrun the allotted time.
The Control task has failed to complete in the allotted amount of time.
The System task has failed to complete in the allotted amount of time.
The 1-millisecond task has failed to complete in the allotted amount of

time.
time.

time.
A DC bus undervoltage event has occurred.

If the bus voltage in parameter 10:13 [DC Bus Memory] falls below the
peak value of the AC line voltage set in parameter 10:286 [UnderVltg
Level], then an undervoltage condition exists.
DC bus voltage exceeded the DC bus overvoltage threshold in parameter

0:28 [DCBusThresh Act].
If parameter 0:26 [DC Bus Trip OVRD] is set to disable, the product’s rated
voltage and voltage class determines the default DC bus overvoltage
threshold.
If parameter 0:26 [DC Bus Trip OVRD] is set to enable, the user-configured
overvoltage threshold in parameter 0:27 [DCBusThreshUser] applies.
Heatsink temperature sensor is reporting a value below -18.7 °C

(-1.66 °F) or the sensor feedback circuit is open.
See parameter 10:362 [Heatsnk Temp Pct] and/or parameter 10:363
[Heatsnk Temp].
The motor or total inertia that is determined by the Autotune inertia test
function is out of range. This condition only occurs during an inertia test.
The motor side inverter application failed to start in the DSP.

The total system inertia result of the Autotune is less than the value in
parameter 10:900 [Motor Inertia], which results in a negative load ratio.
The motor slip result that is determined by the Autotune slip test function
is out of range.
Or, a zero or negative slip is configured for an induction motor. That is, the
value of parameter 10:403 [Motor NP RPM] is greater than or equal to the
value of parameter 10:404 [Mtr NP Sync Spd].
This condition only occurs during a slip test.
The transistor Junction Temperature of the power module has exceeded

the Fault Temperature (varies by rating).
An odd number of motor poles is configured in parameter 10:407 [Motor

Poles].
This parameter should be entered as motor poles and not pole pairs.
Parameter 10:910 [Autotune] is set to 3 ‘Rotate MtrID’ and the value

measured by the Autotune procedure for parameter 10:627 [u PM Ld at 0]
is not in the range of acceptable values (negative).

measured by the Autotune procedure for parameter 10:629 [u PM Ld at
100] is not in the range of acceptable values (negative).

measured by the Autotune procedure for parameter 10:637 [u PM Lq at
25], 10:639 [u PM Lq at 50], 10:641 [u PM Lq at 75], 10:643 [u PM Lq at
100], 10:645 [u PM Lq at 125], 10:647 [u PM Lq at 150], 10:649 [u PM Lq at
175], or 10:651 [u PM Lq at 200] is not in the range of acceptable values.
This could happen if current fails to rise up or decreases too fast due to
abnormal conditions.
For Frames 7…15, in certain situations (either at low frequency and high
output voltage or high frequency and high output voltage) the drive holds
the gate for an IGBT for a longer than desirable time.
Distorted voltage and current results and puts stress on the IGBTs on the
output of the drive.
This alarm does not occur on frames 5 and 6.
A carrier frequency of 1.333 kHz is configured for open loop synchronous

reluctance motor flux vector control.
The minimum carrier frequency supported for synchronous reluctance
open loop flux vector control is 2 kHz.
A carrier frequency of 4 kHz is recommended for best performance with
synchronous reluctance open loop flux vector control.
The product does not support synchronous reluctance open loop flux
vector control with the 1.333 kHz carrier frequency.
The product has started pulse width modulation (PWM) in its motor side
power structure.
The product has stopped pulse width modulation (PWM) in its motor side
power structure.
One of the following invalid autotune configurations has been detected:
An autotune test that is not supported by the active motor control mode
has been requested.
A rotate autotune test has been requested, but the test cannot complete
because velocity limits are too low.
Elapsed percent life of the motor bearing has exceeded the configured
event threshold.
Elapsed life of the motor lubrication has exceeded the configured event
threshold.
Elapsed percent life of the machine bearing has exceeded the configured
event threshold.
Elapsed life of the machine lubrication has exceeded configured event
threshold.
Action
Verify input voltage is within specification. See 750-TD100 for PowerFlex 755T or
An excessive motor load exists.

Reduce load so drive output current
does not exceed the current set by
parameter 10:401 [Motor NP Amps].
An excessive motor load exists.

Verify that the motor nameplate amps are accurately entered in 10:401 [Motor NP Amps].
Reduce load so drive output current does not exceed the current set by parameter 10:401
[Motor NP Amps].
Investigate the load loss event on the motor.
Investigate cause of DC bus ripple.
Increase parameter 10:906 [System BW] or parameter 9:54 [Speed Dev Band] and
parameter 9:55 [SpdBand Intgrtr]
Make sure that the motor data is properly entered. See parameters 10:400 [Motor NP
Volts], 10:401 [Motor NP Amps], 10:402 [Motor NP Hertz], 10:403 [Motor NP RPM], 10:404
[Mtr NP Sync Spd], 10:405 [Mtr NP Pwr Units], 10:406 [Motor NP Power] and 10:407 [Motor
Poles].
If the application uses flux vector control, consider checking the tuning of the drive to the
motor. Consider using the autotune function. See parameter 10:910 [Autotune].
If the fault occurs during deceleration, consider increasing the deceleration time or
changing the stop mode to coast instead of a controlled ramp to stop. See parameters
10:1917 [VRef Decel Time1], 10:1918 [VRef Decel Time2], 10:110 [Mtr Stop Mode A] and
10:111 [Mtr Stop Mode B].
Consider changing the DC bus regulation mode. See parameters 10:116 [Bus Reg Mode A]
and 10:117 [Bus Reg Mode B].
Consider tuning the DC bus regulator. See parameters 10:119 [Bus Reg Level], 10:120 [Bus
Reg Kp], 10:121 [Bus Reg Ki], 10:122 [Bus Limit Kp] and 10:123 [Bus Limit Kd].
If the application uses dynamic braking, make sure dynamic braking is properly configured.
See parameters 10:130 [DB Resistor Type], 10:131 [DB Ext Ohms], 10:132 [DB Ext Watts]
and 10:133 [DB ExtPulseWatts].
Consider adjusting how the drive responds to Decel Inhibit conditions. See parameter
10:170 [Dec Inhibit Actn].
Increase parameter 10:1904 [Overspeed Limit]. If operating in torque mode, ensure no
sudden loss of load.
For closed loop, verify encoder configuration and installation.
Verify mechanical brake function. Increase parameter 9:63 [Brk Slip Thresh] if needed.
Verify mechanical brake function. Increase parameter 9:63 [Brk Slip Thresh] if needed.
Change the value of parameter 10:118 to 0 ‘Bus Memory’ or 1 ‘BusReg Level’.
Operate the drive within -590 Hz to 590 Hz range.
Rotate U/T1, V/T2, W/T3 connections.

If the problem follows the wire, suspect a field wiring problem.
If no change, suspect a problem with the drive.







Decrease load on the motor.
Verify that the drive is sized and derated correctly.

Verify that the correct motor nameplate data is entered.
Decrease load on the motor. Uncouple motor. For induction motors, run a static MotorID
test.
For systems with encoders, perform a Direction test first.
If not intended, ensure no stop signal is issued during an autotune. See parameter 0:604 [M
Last Stop Src].
Investigate feedback device failure.
Normal operation with Start on PowerUp enabled.

Indicates that the drive starts automatically when the delay expires.
Investigate the loss of DI precharge seal signal.
Investigate low DC bus voltage or the reason the drive entered precharge.
Investigate low DC bus voltage or the reason the drive entered precharge.
Verify motor nameplate data and cable length to the motor are correct. See publication
DRIVES-IN001.
Configure the drive to be allowed to reach at least 25% base speed.
Verify motor nameplate data.

Check motor connections.
Rerun autotune.
If the condition persists, modify the value of parameter 10:450 [VCL CReg Damping] and
rerun autotune.
Increase parameter 10:911 [Autotune Psn Lim]. A value of 0 disables the limit.
Check the configuration and connection of stop commands, such as digital inputs, network
connections, and the HIM.
Verify that the drive is sized and derated correctly. See the technical data, publication 750-
TD100 for PowerFlex 755T or publication 750-TD104 for PowerFlex 755TS products.
To clear the fault:

1. Manually move the motor or load until it is no longer beyond the limit.
2. Issue a Clear Fault command.
You cannot clear the fault until the circuit is closed or the input is energized.
To clear the fault:

Manually move the motor or load until it is no longer beyond the limit and then
Issue a Clear Fault command.
You cannot clear the fault until the circuit is closed or the input is energized.
If digital limits (hardware signals) are in use, verify that the following forward and reverse
digital input pairs are not both off: fwd/rev decel travel limit digital inputs and fwd/rev end
stop travel limit digital inputs.
If software travel limits are in use, check the state of the fwd/rev travel limit bits in
parameter 9:51 [Trq Prove Setup]. These bits read an on (1 = Enabled) bit status when the
machine is on limit.
Bit 2 ‘Decel Fwd’ and Bit 4 ‘Decel Rev’ cannot be on simultaneously.
Bit 3 ‘End Stop Fwd’ and Bit 4 ‘Decel Rev’ cannot be on simultaneously.
Bit 3 ‘End Stop Fwd’ and Bit 5 ‘End Stop Rev’ cannot be on simultaneously.
Normal operation that indicates that the profile/indexer is active.

See parameter 10:1200 [Profile Status].
Parameter 10:1202 [Profile Command] Bit 12 disables this alarm.
Normal operation that indicates that the homing function is active.

See parameter 10:1641 [Homing Status].
Parameter 10:1640 [Psn Redefine Bit 5 disables this alarm.
Perform the homing function or position redefine before starting the profile.
Select either bit 1 ‘Home DI’ or bit 8 ‘Home to Torque’ in parameter 10:1640 [Home Ctrl
Opts].
• Set bit 1 ‘Home DI’ and clear bit 8 ‘Home to Torque’ if a digital input is used as an input to
detect homing event for the homing function.
• Set bit 8 ‘Home to Torque’ and clear bit 1 ‘Home DI’ if a hard stop is used as input to
Select either bit 1 ‘Home DI’ or bit 8 ‘Home to Torque’ in parameter 10:1640 [Home Ctrl
Opts].
• Set bit 1 ‘Home DI’ and clear bit 8 ‘Home to Torque’ if a digital input is used as an input to
• Set bit 8 ‘Home to Torque’ and clear bit 1 ‘Home DI’ if a hard stop is used as input to
Configure a Z channel in the position regulation feedback source that is used for the homing
marker option or disable the homing marker option.
• Replace the feedback source configured in parameter 10:1013 [PReg Fb Sel] with a source
that supports a Z channel.
• For a feedback source that supports a Z channel, enable the Z channel in the feedback
option module configuration parameter for the feedback source.
• To disable the homing marker option, clear bit 2 ‘Home Marker’ in parameter 10:1640
[Home Ctrl Opts].
If digital limits (hardware signals) are in use, verify that the digital inputs are connected to
normally closed contacts. When the end limit is reached the contacts open.
If digital limits (hardware signals) are in use, verify that the digital inputs are connected to
normally closed contacts. When the end limit is reached the contacts open.
Correct parameter configuration.
See parameters 10:480 [Start Acc Boost]…10:484 [Break Frequency] and correct to have a
positive V/Hz slope. Verify motor nameplate data.
Correct parameter configuration.
Set parameter 10:486 [VHz Curve] to 0 ‘Custom V/Hz’ or select a non permanent magnet
V/Hz mode.
Check the settings of parameters 10:130 [DB Resistor Type] through 10:133 [DB
ExtPulseWatts].
Set parameter 12:55 [Toq Accy Mod Cfg] Bit 4 ‘VltOfstMode’ to a 1 when the drive is
stopped to recalibrate the TAM.
See the PowerFlex 755T Flux Vector Tuning Application Technique, publication 750-AT006.
Verify that the settings of parameters 10:425 [PWM Frequency] and 10:1898 [Vel Limit
Pos]. Lower carrier frequencies reduce the output frequency range.
Verify that parameter 10:1900 [Vel Low Lim Pos] is less than or equal to parameter 10:1898
[Vel Limit Pos].
Verify that the settings of parameters 10:425 [PWM Frequency] and 10:1899 [Vel Limit
Neg]. Lower carrier frequencies reduce the output frequency range.
Verify that parameter 10:1901 [Vel Low Lim Neg] is greater than or equal to parameter
10:1899 [Vel Limit Neg].
Select either bit 0 or bit 1 in parameter 10:580 [PM Config].
Verify parameter 10:407 [Motor Poles] is correct.

If failure occurred because of movement limitation, increase 10:587 [PM OfstTst Cur]
parameter.
If this fails to correct the problem, the load on the motor may be too high or a mechanical
brake is applied.
Retune the application by adjusting the proportional and integral gains for the position
regulator.
Check motor cable connections and/or damaged motor leads. Perform motor insulation
tests.
—
Make sure that the value set in parameter 10:698 [PM Max Cur] is correct.
Check the motor windings, cables, and connections.
Make sure that the product is configured correctly.
—
Ensure the drive is properly sized for the application. Reduce motor load if possible.
If starting into a rotating load, turn on flying start with parameter 10:70 [FlyingStart Mode].
Check the motor and external wiring to the drive output terminals for a shorted condition.
Perform an insulation resistance test on the wiring to the motor.
Check for devices between the drive and motor such as a contactor that may be changing
states while the drive is running.
Ensure encoder is functioning properly if used.
For applications with high load and low input voltage, this condition can be alleviated by
reducing the value of parameter 10:428 [Bus Utilization] to 92%.
If starting into a rotating load, turn on flying start with parameter 10:70 [FlyingStart Mode].
Check the motor and external wiring to the drive output terminals for a shorted condition.
Check for devices between the drive and motor such as a contactor that may be changing
states while the drive is running.
Ensure encoder is functioning properly if used.
Check cabinet filters, heatsink fans, intake air temperatures, and the baffles that can restrict
recirculation of heated air.
Verify adequate airflow and the baffles that help prevent recirculation of heated air.
Clear faults.
If the fault persists, rerun firmware update and/or replace the main control board.
See the hardware service manual, publication 750-TG100 for PowerFlex 755T or publication
750-TG101 for PowerFlex 755TS products, for the replacement procedure.
Clear faults.
Clear faults.
Clear faults.
Clear faults.
Clear faults.
If the fault persists, remove any unnecessary Option Cards from the drive.
If the fault persists rerun the firmware update and or replace the main control board.
Clear faults.
Clear faults.
Clear faults.
Clear faults.
Clear faults.
Verify parameter 10:13 [DC Bus Memory] is similar to the DC bus measurement from the
test points on the Mn power modules.
Monitor the DC bus voltage in parameter 0:3 [DC Bus Volts] in relation to the DC bus
overvoltage threshold in parameter 0:28 [DCBusThresh Act].
Possible causes include: Configuration of line side converter, configuration of DC bus
regulator, high inertia loads, and fast decel times.
For drives with a dynamic brake resistor installed, verify that the brake wiring and the
parameter configuration are correct.
publication 750-TD100 for PowerFlex 755T or publication 750-TD104 for PowerFlex 755TS
products.
Verify motor nameplate data. Rerun inertia Autotune.
Cycle power.
Determine if the value of parameter 10:900 [Motor Inertia] is too high.
If possible, uncouple the motor from the load and perform the motor inertia autotune test.
Verify motor nameplate data. Ensure parameter 10:403 [Motor NP RPM] is not set to
synchronous RPM. Rerun rotate motorID test.
Verify motor nameplate data and drive tuning for proper starting torque.
Change the value of parameter 10:407 [Motor Poles] to an even number.
Verify motor nameplate data and rerun the rotate motor ID test. If fault continues, obtain
the motor datasheet from motor vendor.
Set Parameter[Mtr Cfg Options] bit 8 ‘DutyClampEn’.
This setting limits the duty cycle of the drive.
This setting can also result in distorted voltage and current however the stress on the IGBTs
is reduced.
Change the PWM carrier frequency configured in parameter 10:425 [PWM Frequency] to 2
kHz or higher.
Alternatively, change the selected velocity feedback source to a source other than an open
loop.
That is, if parameter 10:1019 [Fb Loss Action] is set to primary only, change parameter
10:1000 [Pri Vel Fb Sel] to select a source other than an open loop.
If parameter 10:1019 [Fb Loss Action] is set to alternate only, change parameter 10:1006
[Alt Vel Fb Sel] to select a source other than an open loop.
If parameter 10:1019 [Fb Loss Action] is set to automatic tachometer switchover, change
both parameter 10:1000 [Pri Vel Fb Sel] and parameter 10:1006 [Alt Vel Fb Sel] to select a
source other than an open loop.
To resolve a mismatch between the active motor control mode and the requested autotune
test:
- Change the value of parameter 10:910 [Autotune] to select a tuning test that is supported
by the active motor control mode. Alternatively, change the control mode for the active
motor control port to a mode that supports the requested autotune test.
To resolve an invalid autotune configuration that prevents completion of a rotate autotune
test:
- If the commanded direction is forward, increase the value of parameter 10:1898 [Vel Limit
Pos] so that it is greater than 75% of the motor nameplate speed configured in parameters
10:402 [Motor NP Hertz] and 10:403 [Motor NP RPM].
- If the commanded direction is reverse, decrease the value of parameter 10:1899 [Vel Limit
Neg] (a negative value) so that its absolute value is greater than 75% of the motor
nameplate speed configured in parameters 10:402 [Motor NP Hertz] and 10:403 [Motor NP
RPM].
Alternatively, increase the value of parameter 10:912 [Autotune Vel Lim].
Service the motor bearing and reset the predictive maintenance function for the bearing.
Perform motor lubrication and reset the predictive maintenance function for it.
Service the machine bearing and reset the predictive maintenance function for the bearing.
Perform machine lubrication and reset the predictive maintenance function for it.
Configurable 10:270 [Power Loss Actn]

— —
Configurable 10:200 [Mtr OL Action]

Configurable 10:250 [Load Loss Action]

Configurable 10:289 [InPhase LossActn]

Coast —
Configurable 10:256 [OutPhaseLossActn]
Configurable 10:170 [Dec Inhibit Actn]

— —
— —
— —

fault.








Configurable 10:242 [Shear Pin 1 Actn]
Configurable 10:245 [Shear Pin 2 Actn]

— —

OVRD] bit 3 ‘MS Pwr Flts’

fault.

fault.


fault.
fault.

OVRD] bit 8 ‘Fdbk Faults’

Coast (Motor Side Inverter) 10:1019 [Fb Loss Action]

— —
Configurable 0:39 [Prchrg Err Cfg]

Additional Fault Action 0:191 [DI Prchrg Seal]
— 0:37 [Prchrg Control]

0:190 [DI Precharge]
0:191 [DI Prchrg Seal]
Coast (Motor Side Inverter) 0:37 [Prchrg Control]

Additional Fault Action 0:190 [DI Precharge]
Fault opens main circuit breaker: No 0:191 [DI Prchrg Seal]
fault.
fault.

Emergency override response: N/A

fault.

fault.

— 10:1921 [Accel Limit]
— 10:1922 [Decel Limit]
— —
— —
— 0:184 [DI PHw OvrTrvl]

— 0:185 [DI NHw OvrTrvl]

Current Limit Stop (Motor Side Inverter) —

fault.
— —
— —
— —
— —
— —


— —
— —
— —
— —
— —

fault.
— —
— —
— —

fault.

fault.
— Configured with Logix

controller.
Configurable 0:420 [M Gnd Warn Actn]

Configurable 0:425 [HRG GF Flt Actn]

— —
— —

Configurable 10:941 [Ref Fault Config]

Configurable 10:941 [Ref Fault Config]


fault.


fault.

fault.
fault.

fault.

fault.

fault.

fault.

fault.

fault.
fault.

fault.
Configurable 10:285 [UnderVltg Action]


fault.


fault.
Additional Fault Action —

fault.
fault.
— —

— —

fault.

fault.

fault.
— —
— —
— —
— —
— —
— —
— —
— —
— —
— —
Configurable Action
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
—
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
Ignore
Alarm
Flt Minor
FltCoastStop
—
—
—
—
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
—
—
FltCoastStop
Flt RampStop
Flt CL Stop
—
—
Ignore
Alarm
Ignore
Alarm
—
—
—
—
—
—
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
Ignore
Alarm
Flt Minor
FltCoastStop
Flt CL Stop
Ignore
Alarm
Flt Minor
FltCoastStop
Flt CL Stop
—
—
—
—
—
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
—
—
—
—
Ignore
Alarm
Ignore
Alarm
Ignore
Alarm
Ignore
Alarm
Condition Type Condition Code Display Text Full Tex
Resettable Fault 12002 ConstantsMsgIvld Constants Message Invalid Fault
Non-Resettable 12003 Constants Chksum Constants Checksum Fault

Fault

Fault
Resettable Fault 12005 Power Supply UV Power Supply Undervoltage
Resettable Fault 12006 Precharge Fault Precharge Fault
Resettable Fault 12007 MCS CL BayOTmp MCS Failed to Close or Wiring Bay
Overtemp
Resettable Fault 12008 MCS Shunt Trip MCS Shunt Trip
Resettable Fault 12009 MCS Aux Mismatch MCS Aux Mismatch or Wiring Bay
Overtemp
Resettable Fault 12010 240VAC Loss Flt 240V AC Loss Fault
Resettable Fault 12011 240VAC OV 240VAC Over Voltage
Resettable Fault 12012 FDOpen MCSClose Fused Disconnect Open (MCS Closed)
Resettable Fault 12013 SysPwr OC Fault SysPwr OC Fault

Resettable Fault 12017 Gate Drive Flt Gate Drive Fault
Resettable Fault 12018 Fiber Offline Fiber Went Offline
Resettable Fault 12019 SysPwr OV Flt SysPwr OV Fault
Resettable Fault 12020 N24V UV Flt Neg 24V Undervoltage Fault
Resettable Fault 12022 Pred NVS Error Predictive Maintenance Non-Volatile

Storage Error
Resettable Fault 12023 CtrlMsgWdog Tout Control Msg Watchdog Timeout
Alarm 2 12024 TAM Cal Missing TAM Calibration Missing
Non-Resettable 12025 Incom GateDr Flt Incompatible Gate Drive Fault

Fault
Resettable Fault 12026 Ground Flt Ground Fault
Resettable Fault 12027 Bus OV Flt Bus OV Fault
Resettable Fault 12028 NTC-U Short Flt NTC-U Short Fault

Resettable Fault 12029 NTC-U Open Flt NTC-U Open Fault
Resettable Fault 12030 U OverTemp Flt Heatsink-U OverTemp Fault
Alarm 1 12031 U OverTemp Alm Heatsink-U OverTemp Alarm
Resettable Fault 12032 U LowTemp Flt Heatsink-U LowTemp Fault
Alarm 1 12033 U LowTemp Alm Heatsink-U LowTemp Alarm

Resettable Fault 12034 NTC-V Short Flt NTC-V Short Fault
Resettable Fault 12035 NTC-V Open Flt NTC-V Open Fault
Resettable Fault 12036 V OverTemp Flt Heatsink-V OverTemp Fault
Alarm 1 12037 V OverTemp Alm Heatsink-V OverTemp Alarm
Resettable Fault 12038 V LowTemp Flt Heatsink-V LowTemp Fault

Alarm 1 12039 V LowTemp Alm Heatsink-V LowTemp Alarm
Resettable Fault 12040 NTC-W Short Flt NTC-W Short Fault
Resettable Fault 12041 NTC-W Open Flt NTC-W Open Fault
Resettable Fault 12042 W OverTemp Flt Heatsink-W OverTemp Fault
Alarm 1 12043 W OverTemp Alm Heatsink-W OverTemp Alarm

Resettable Fault 12044 W LowTemp Flt Heatsink-V LowTemp Fault
Alarm 1 12045 W LowTemp Alm Heatsink-W LowTemp Alarm
Alarm 1 12047 Jnt OverTemp Alm Junction OverTemp Alarm
Resettable Fault 12048 Str Overload Flt Stator Overload Fault
Alarm 1 12049 Str Overload Alm Stator Overload Alarm

Resettable Fault 12050 Bus Fuse Harness Bus Fuse Harness
Resettable Fault 12051 Bus PosFuseBlown Bus Positive Fuse Blown
Resettable Fault 12052 Bus NegFuseBlown Bus Negative Fuse Blown
Configurable 12053 DCP MCS Life MoldedCaseSwitch Life Threshold

Exceeded
Resettable Fault 12060 Volt Class Flt Voltage Class Fault
Resettable Fault 12061 Duty Rating Flt Duty Rating Fault
Resettable Fault 12062 Pwr UnitTyp Flt Power Unit Type Fault
Resettable Fault 12063 DTM ConstCorrFlt DTM Constants Corrupted Fault
Alarm 1 12064 Main Blower Alm Main Blower Alarm
Resettable Fault 12065 Main Blower Flt Main Blower Fault
Alarm 1 12070 Board OT Alarm Board OT Alarm

Resettable Fault 12071 Board OT Fault Board OT Fault
Alarm 1 12072 Board UT Alarm Board UT Alarm
Resettable Fault 12073 Board UT Fault Board UT Fault
Alarm 1 12074 IntakeAirOT Alrm Intake Air OT Alarm
Resettable Fault 12075 IntakeAir OT Flt Intake Air OT Fault
Alarm 1 12076 IntakeAirUT Alrm Intake Air UT Alarm
Resettable Fault 12077 IntakeAir UT Flt Intake Air UT Fault
Alarm 1 12078 PIB OT Alarm PIB OT Alarm

Resettable Fault 12079 PIB OT Fault PIB OT Fault
Alarm 1 12080 PIB UT Alarm PIB UT Alarm
Resettable Fault 12081 PIB UT Fault PIB UT Fault
Alarm 1 12082 Offset Alm Offset Alarm

Alarm 1 12083 Bus Imbalanc Alm Bus Imbalance Alarm
Resettable Fault 12084 Bus Imbalanc Flt Bus Imbalance Fault
Resettable Fault 12085 PWM Enable Flt PWM Enable w/o DTM Active Fault
Resettable Fault 12086 L/R Overtemp L/R Overtemp

Resettable Fault 12087 BusCond BayOTmp Bus Conditioner Fault or Wiring Bay
Overtemp
Resettable Fault 12088 Sec Fbk Watchdog Secondary Feedback Watchdog
Alarm 1 12089 ISO UV ISO Under Voltage
Configurable 12090 CabAirHiTempRise Cabinet Air High Temperature Rise
Configurable 12091 CabAirLoTempRise Cabinet Air Low Temperature Rise
Configurable 12092 HS Fan Life Heatsink Fan Life Threshold

Exceeded
Configurable 12093 IGBT Life IGBT Life Threshold Exceeded
Configurable 12094 Bus Cap Life Bus Capacitor Life Threshold

Exceeded
Configurable 12095 Stir Fan Life Stirring Fan Life Threshold Exceeded
Resettable Fault 12096 U Pos IOC Flt U Pos IOC Fault
Resettable Fault 12097 V Pos IOC Flt V Pos IOC Fault
Resettable Fault 12098 W Pos IOC Flt W Pos IOC Fault
Resettable Fault 12099 U Neg IOC Flt U Neg IOC Fault
Resettable Fault 12100 V Neg IOC Flt V Neg IOC Fault
Resettable Fault 12101 W Neg IOC Flt W Neg IOC Fault
Resettable Fault 12102 LocPwr UV Flt LocPwr UV Fault

Resettable Fault 12104 P24 UV Flt Pos 24V Undervoltage Fault
Resettable Fault 12107 DC Fuse Open DC Fuse Open
Configurable 12108 240VAC Low 240V AC Low
Alarm 2 12109 240VAC Loss 240V AC Loss
Configurable 12110 FDOpen MCSOpen Fused Disconnect Open (MCS Open)
Alarm 1 12126 Pwr Bd Alarm Power Board Alarm
Resettable Fault 12127 Pwr Bd Fault Power Board Fault

Alarm 1 12131 Flash Timeout HSI Flash Timeout
Alarm 1 12132 FlashRst Timeout HSI Flash Reset Timeout
Alarm 1 12133 Login Timeout HSI Login Timeout
Alarm 1 12134 Flash DPI Error Flash DPI Error
Resettable Fault 12136 Mtrside IOC Flt IOC Fault
Non-Resettable 12137 Pwr Struc Fault Power Structure Fault

Fault
Fault
Communication between the main control board and the image buffer in one
of the power peripherals (power layer interface board, torque accuracy
module, or DC precharge board) has stopped transmitting for 10 milliseconds.
The constants header information did not match the content of the power
peripheral (power layer interface board, torque accuracy module, or DC
precharge board).
The constants download failed the checksum test by one of the power
peripherals (power layer interface board, torque accuracy module, or DC
precharge board).
Checksum test failed for non-volatile data for the DC precharge board.
An undervoltage event occurred in the local (internal to the PIB) power supply.
A possible cause is the DC bus voltage, which feeds the power supply, has
dropped below 400V DC.
This power supply provides power to the power layer interface board or DC
precharge board (if present).
Main control board firmware did not indicate that bus voltage was good
within the specified time period following closure of the precharge contactor.
Two conditions can cause this fault:

Condition 1: The molded case switch (MCS) in the DC precharge has failed to
close when commanded.
Condition 2: The temperature in the input bay or entry wiring bay has risen
too high. This condition can only cause the fault before the drive or bus supply
has completed precharge.
The molded case switch (MCS) in the DC precharge has failed to open within
the specified time.
Two things conditions can cause this fault:

Condition 1: The auxiliary contact on the molded case switch (MCS) in the DC
precharge is not functioning properly.
Or
Condition 2: The temperature in the input bay or entry wiring bay has risen
too high. This condition can only cause the fault before the drive or bus supply
has completed precharge. Investigate causes for over- temperature in these
bays.
The 240V AC supply voltage fell below the specified minimum voltage level of
154V AC during the pre-charge cycle or while the molded case switch (MCS) is
closed.
See the corresponding [DCPn PwrSup Vltg] port 12 parameter.
The 240V AC supply voltage rose above the specified maximum voltage level
of 283V AC.
Firmware detected that the fused disconnect was opened when molded case
switch (MCS) was open.
An over current event occurred in the local (internal to the PIB) power supply.
It affects the operation of the positive 24V power supply.
The most likely cause is a component failure in the Mn PIB, DCPC, or power
module.
A Gate Drive Board fault has occurred.
Possible causes include an internal power supply failure (if the fault occurred
before the drive or bus supply was enabled), or an IGBT desaturation (over
temperature or over current) event.
The fiber-optic communication link between the fiber interface circuit board
and one of the power peripherals (power layer interface board, torque
accuracy module, or DC precharge board) transitioned from online to offline.
An overvoltage event occurred in the local (internal to the PIB) power supply.
The most likely cause is component failure.
It affects the operation of the negative 24V power supply.
Data from Electronically Erasable Read Only Memory (EEROM) on the power
board or DC precharge board of a power module within the motor side
inverter is corrupt.
The watch dog timer for transmission of the control message between the
main control board and one of the power peripherals (power layer interface
board or torque accuracy module) has timed out.
The factory has not calibrated the torque accuracy module (TAM) installed in
the product.
An incompatible gate drive board is installed.

Power layer interface (PLI) hardware in the power module has detected a
ground fault event.
Ground current is greater than 25% of the power module rating.
DC bus voltage exceeded the DC bus overvoltage threshold in parameter 0:28

[DCBusThresh Act].
threshold.
The heatsink temperature sensor (NTC) for the U (T1) phase of the power
module indicates a short circuit (the value has risen above 150 °C).
The sensor or circuit is faulty. See the corresponding parameter in port 12 [Mn
HeatsinkTempU]
The heatsink temperature sensor (NTC) for the U (T1) phase of the power
module indicates an open circuit (the value has fallen below -40 °C).
HeatsinkTempU]
The temperature in the heatsink for the U (T1) phase of the power module has
risen above 118 °C.
improper derating for temperature and altitude, and obstructed airflow. See
the corresponding parameter in port 12 [Mn HeatsinkTempU].
PowerFlex 755TS drives have only one heatsink temperature sensor. The
signal from that sensor feeds the parameters for U, V, and W phases.
the corresponding parameter in port 12 [Mn HeatsinkTempU].
fallen below -30 °C for a PowerFlex 755TR, 755TL, or 755TM product or -25 °C
for a PowerFlex 755TS product.
The most common cause is an ambient temperature that is too low for
operation. See the corresponding parameter in port 12 [Mn HeatsinkTempU].
operation. See the corresponding parameter in port 12 [Mn HeatsinkTempU].
The heatsink temperature sensor (NTC) for the V (T2) phase of the power
HeatsinkTempV].
The heatsink temperature sensor (NTC) for the V (T2) phase of the power
module indicates an open circuit (the value has fallen below -40 °C).
HeatsinkTempV].
The temperature in the heatsink for the V (T2) phase of the power module has
the corresponding parameter in port 12 [Mn HeatsinkTempV].
the corresponding parameter in port 12 [Mn HeatsinkTempV].
operation. See the corresponding parameter in port 12 [Mn HeatsinkTempV].
The heatsink temperature sensor (NTC) for the W (T3) phase of the power
HeatsinkTempW].
The heatsink temperature sensor (NTC) for the W (T3) phase of the power
module indicates an open circuit (the value has fallen below - 40 °C).
HeatsinkTempW].
The temperature in the heatsink for the W (T3) phase of the power module
has risen above 118 °C.
the corresponding parameter in port 12 [Mn HeatsinkTempW].
the corresponding parameter in port 12 [Mn HeatsinkTempW].
has fallen below -25 °C for a PowerFlex 755TR, 755TL, or 755TM product or -
15 °C for a PowerFlex 755TS product.
operation. See the corresponding parameter in port 12 [Mn HeatsinkTempW].
The transistor junction temperature of the power module has exceeded the
Fault Temperature which is 155 °C for 3.5 sec or 165 °C.
improper derating for temperature and altitude, improper flying start
configuration, and obstructed airflow. See the corresponding parameter in
port 12 [Mn IGBT Temp]. Note: This temperature may rise/fall faster than the
update rate of the drive.
The transistor junction temperature of the power module has exceeded the
alarm temperature which is 155 °C.
improper derating for temperature and altitude, improper flying start
configuration, and obstructed airflow. See the corresponding parameter in
port 12 [Mn IGBT Temp]. Note: This temperature may rise/fall faster than the
update rate of the drive.
The Current Overload Count of the power module has exceeded 100%.
Possible causes include loads that require too much torque and current.
The Current Overload Count of the power module has exceeded 50%. Possible
causes include loads that require too much torque and current.
A DC bus fuse harness is missing or disconnected.
The positive DC link fuse has cleared.
The negative DC link fuse has cleared.
Elapsed life of molded case switch in the DC precharge module has exceeded
the configured event threshold.
The voltage class that is programmed in the power module is incorrect or

corrupt.
The duty rating that is programmed in the power module is incorrect or

corrupt.
The power unit type that is programmed in the power module is incorrect or
corrupt.
Runtime constants data corruption detected.
The Mn heatsink fan is running below the alarm threshold speed.

For frame 5 drives:
The threshold is 6460 RPM while the drive is modulating, and 1593 RPM while
the drive is not modulating.
For frame 6 products (drives and bus supplies):
The threshold is 6375 RPM while the product is modulating, and 1593 RPM
while the product is not modulating.
For frame 7 products:
For frame 8…15 products:
The Mn heatsink fan is running below the fault threshold speed.

For frame 5 drives:
The threshold is 6460 RPM while the drive is modulating, and 1593 RPM while
the drive is not modulating.
For frame 6 products (drives and bus supplies):
For frame 7 products:
For frame 8…15 products:
The threshold is 1800 RPM while the product is modulating, and 60 RPM while
the product is not modulating.
The temperature of one of the power peripherals (power layer interface

board, torque accuracy module, or DC precharge board) has exceeded the
alarm temperature (75 °C).
The alarm temperature for a PowerFlex 755TS torque accuracy module is 95
°C.
See the corresponding parameter in port 12 [Mn PLI BoardTemp] and/or
[DCPn Board Temp].
board, torque accuracy module, or DC precharge board) has exceeded the
fault temperature (80 °C).
The fault temperature for a PowerFlex 755TS torque accuracy module is 99 °C.
[DCPn Board Temp].

board, torque accuracy module, or DC precharge board) has fallen below the
alarm temperature (-25 °C).
The most likely cause is low ambient temperature.
[DCPn Board Temp].

board, torque accuracy module, or DC precharge board) has fallen below the
fault temperature (-30 °C).
The most likely cause is low ambient temperature. See the corresponding
parameter in port 12 [Mn PLI BoardTemp] and/or [DCPn Board Temp].
Power module intake air has exceeded the alarm temperature (60 °C). See the
corresponding parameter in port 12 [Mn Meas Amb Tmp].
Power module intake air has exceeded the fault temperature (70 °C). See the
corresponding parameter in port 12 [Mn Meas Amb Tmp].
Power module intake air has fallen below the alarm temperature (-10 °C). See
the corresponding parameter in port 12 [Mn Meas Amb Tmp].
Power module intake air has fallen below the fault temperature (-25 °C). See
the corresponding parameter in port 12 [Mn Meas Amb Tmp].
The power interface board (PIB) has exceeded the alarm temperature (75 °C).
See the corresponding parameter in port 12 [Mn PIB BoardTemp].
The power interface board (PIB) has exceeded the fault temperature (80 °C).
The power interface board (PIB) has fallen below the alarm temperature (-25
°C).
Possible causes include low ambient temperature and obstructed airflow.
The power interface board (PIB) has fallen below the fault temperature (-30
°C).
Control has detected excessive DC offset.

The DC bus voltage imbalance between Mn power modules has exceeded the
alarm threshold. See the corresponding parameter in port 12 [Mn DC
BusVoltage].
The DC bus voltage imbalance between Mn Power modules has exceeded the
fault threshold. See the corresponding parameter in port 12 [Mn DC
BusVoltage].
Control attempted to modulate before the thermal manager was running.
An over temperature event has occurred in the parallel inductor or dv/dt filter.
High temperature caused the thermal switch to open. Check cabinet filters,
heatsink fans, intake air temperatures, and the baffles that help prevent
recirculation of heated air. See the corresponding diagnostic item in port 12
[MnStatusWord] Bit 2 ‘LR OvrTempSw’.
Two conditions can cause this fault in a frame 8 or larger drive or CBI:
Condition 1: A bus conditioner is not functioning properly.
Condition 2: High temperature in the optional exit wiring bay can only cause
the fault in the last motor side inverter power module. For example, in a
frame 9 drive that is M1, or in a frame 11 drive that is M3. If the fault occurs in
a power module that is not the last motor side inverter power module, the
cause must be a bus conditioner. If the fault occurs in a power module that is
part of the line side converter, the cause must be a bus conditioner.
Transmission of the feedback message (PDI fiber connection on the Mn PLI)

from the DC precharge module has timed out.
An undervoltage event occurred in the local (internal to the Mn PIB board)

power supply.
Possible causes include low voltage on the customer supplied 24V DC auxiliary
power (if used) or component failure.
The high temperature rise function has detected an event when the
temperature in the power module has risen higher than expected for the load
and ambient temperature.
Possible causes include blocked cabinet filters and improper internal airflow.
The low temperature rise function has detected an event when the
temperature in the power module has failed to rise as expected for the load
and ambient temperature.
Possible causes include missing cabinet filters or open doors.
Elapsed life of the Mn heatsink fan has exceeded the configured event
threshold.
Elapsed life of Mn power module IGBTs has exceeded the configured event
threshold.
Elapsed life of Mn power module DC bus capacitors has exceeded the

configured event threshold.
Elapsed life of the stirring fans has exceeded the configured event threshold.
The Mn power layer interface (PLI) hardware in the power module has
detected an instantaneous over current (IOC) event on the positive side of the
U (T1) output phase.
V (T2) output phase.
W (T3) output phase.
detected an instantaneous over current (IOC) event on the negative side of
the U (T1) output phase.
the V (T2) output phase.
the W (T3) output phase.
An undervoltage event occurred in the local (internal to the Mn PIB) power

supply. It affects the operation of the positive or negative 12V power supply.
One of the power peripherals (power layer interface board, torque accuracy
module, or DC precharge board) has stopped transmitting messages to the
main control board.
A DC fuse that connects the input of the Mn power module to the DC bus has
opened.
The 240V AC supply voltage is between 154V AC and 187V AC.

The 240V AC supply voltage fell below the specified minimum voltage level of
154V AC while the molded case switch (MCS) is opened.
Firmware detected the fused disconnect was opened when Molded Case
Switch (MCS) was open.
A condition exists on the power board that indicates a malfunctioning stirring

fan.
The fan is either stopped or it is running below 9350 RPM.
This alarm is frame-dependent.
The power board temperature has exceeded the maximum threshold.

Catastrophic power structure failure can result if the drive is allowed to
modulate in this state.
This fault is frame-dependent.
The Predictive Maintenance function has reset an elapsed life parameter.
A Flash time-out occurred between one of the power peripherals (power layer
interface board, torque accuracy module, or DC precharge board) and the
main control board during a firmware update.
A Flash reset time-out occurred between one of the power peripherals (power
layer interface board, torque accuracy module, or DC precharge board) and
the main control board during a firmware update.
One of the power peripherals (power layer interface board, torque accuracy
module, or DC precharge board) has failed to log in with the main control
board after a firmware update.
A Flash DPI error has occurred between one of the power peripherals (power
layer interface board, torque accuracy module, or DC precharge board) and
the main control board during a firmware update.
Motorside hardware has detected an Instantaneous Over Current (IOC).
A voltage imbalance has been detected in the DC bus capacitor circuit that
indicates a compromised power circuit.
Action
Cycle power.
Cycle power.
Cycle power.
If the fault persists, replace the DC precharge board.
See the hardware service manual, publication 750-TG100 for PowerFlex 755T or publication 750-TG101 for PowerFlex
Verify DC bus is present on the Mn power module via the hardware testpoints. If so, replace the Mn power interface
board (PIB).
See hardware service manual, publication 750-TG100 for PowerFlex 755T or publication 750-TG101 for PowerFlex 755TS
products, for the replacement procedure.
Check the timing of the rise of the DC bus following precharge.
Condition 1: Inspect the DC precharge module and the thermal sensor harness for the exit wiring bay. Ensure MCS
lockout device is not closed. See the Service Manual, publication 750-TG100 for PowerFlex 755T or publication 750-
TG101 for PowerFlex 755TS products, for details.
Condition 2: Check the enclosure filters and fans. Problems with the baffling between these bay and adjacent bays can
be sources of heat.
Power down.
Replace the MCS.
Then reset the MCS elapsed life parameter.
Check the circuit breaker.

Check the Predictive Maintenance parameters for the MCC.
Check the enclosure filters and fans.
Check the thermal sensor harness for the input bay or entry wiring bay or bypass jumper.
Check the Predictive Maintenance objects for these fans.
Check the baffling between these bays and adjacent bays that can be sources of heat.
Condition 1: Inspect the DC precharge module and the thermal sensor harness for the exit wiring bay.
Condition 2: Check the enclosure filters and fans. Problems with the baffling between these bay and adjacent bays can
be sources of heat.
See the Service Manual, publication 750-TG100 for PowerFlex 755T or publication 750-TG101 for PowerFlex 755TS
products, for details on these devices.
Verify that the 240V AC input is within specification.

Inspect DCPC module 240V AC supply fuses and connections.
755TS products, for the system schematics.

Power down and check the wiring in the DC precharge module.
Replace failed component.

Inspect status indicators on power layer interface (PLI) circuit board.
Replace the Mn power module.
Clear faults.
If the fault persists, power down and then check the fiber-optic communication connections.

Replace the Mn power module or PLI.

Replace the Mn power module or PLI.
Cycle power.
If the fault persists, replace the Mn power module.
Power down and then check the fiber-optic communication connections (fiber-optic cables and transceivers).
To clear the alarm, clear bit 0 ‘Module Enbl’ in parameter 12:55 [Trq Accy Mod Cfg] to disable the TAM.
Remove power to the product.
Replace the TAM.
A frame 5 or 6 PowerFlex 755TR, 755TL, or 755TM product with TAM will need to be replaced.
Inspect status indicators on PLI.

For drive frames 5 and 6, power down the drive and perform the following checks. After completing each set of checks,
you can return the drive to service to see if the drive continues to fault.
1. Check the power cable connections.
a. Verify that the power cable connections to the drive are secure.
b. Verify that the power cable connections at the motor are secure.
c. Perform a phase to ground check on both the line side and load side.
d. Inspect all electrical tape, heat shrink, or other material that is used to insulate cable splices for coverage gaps, pin
holes, or other weak points where an arc can occur.
e. Verify that the ground wire is connected to the drive and to the motor frame.
2. Perform insulation tests on the motor and the motor cables.
a. Disconnect the motor leads from the inverter.
b. Perform a Megger or surge test on the disconnected motor. Replace the motor if necessary.
For drive frames 7…15, power down the drive and perform the following checks. After completing each set of checks,
you can return the drive to service to see if the drive continues to fault.
For drives that have multiple inverters, frames 9…15, see parameter 12008 [M Side Fault] to determine which inverter is
causing this fault.
1. Check the motor cable connections.
a. Verify that the motor cable connections at the inverter are secure.
b. Verify that the motor cable connections at the motor are secure.
c. Inspect all electrical tape, heat shrink, or other material that is used to insulate cable splices for coverage gaps, pin
holes, or other weak points where an arc can occur.
d. Verify that the ground wires are connected to the drive and to the motor frame.
2. Perform insulation tests on the motor and the motor cables.
b. Perform a Megger or surge test on the disconnected motor. Replace the motor if necessary.
3. Check for loose connections between the DC bus and the power module.
For drives with DC link hardware:
a. Verify that all DC link fuse connections are tightened to the specified torque.
b. Verify that the power connections between the DC link and the input terminals of the power module are tightened to
the specified torque.
For drives with DC Precharge modules:
a. Verify that the power connections between the DC link and the input terminals of the power module are tightened to
the specified torque.
b. Verify that all DC link fuse connections are tightened to the specified torque.
4. Test the power module and DC precharge module.
b. Run the inverter with no motor connected.
Monitor the DC bus voltage in parameter 0:3 [DC Bus Volts] in relation to the DC bus overvoltage threshold in parameter
Possible causes include: Configuration of Line Side Converter, configuration of DC bus regulator, high inertia loads, and
fast decel times.
For regenerative converters, verify the regeneration configuration parameters.
For non-regenerative converters, increase decel time or provide a means to dissipate excess energy.


Verify adequate airflow and the ambient temperature is within specification. See the technical data, publication 750-

Verify that the ambient temperature is within specification. See the technical data, publication 750-TD100 for PowerFlex
755T or publication 750-TD104 for PowerFlex 755TS products.








Verify drive configuration for proper starting torque and motor nameplate data.

Verify drive configuration for proper starting torque and motor nameplate data.
Check drive and load sizing.

Check mechanical factors that increase the amount of torque and current.

Power down and examine the DC bus fuse harness
Power down.
Investigate why the DC link fuse cleared and correct.
Replace both DC link fuses.
Perform component test procedures.
Power down.
Replace both DC link fuses.
During the next scheduled downtime, replace the molded case switch.
Then reset the molded case switch life object.
Cycle power.
If the fault persists, replace the PIB board and/or the Mn power module.
Cycle power.
Cycle power.
Clear the fault.
Cycle power.
If the fault persists, replace Mn power layer interface (PLI) circuit board.
Power down.
Replace the Mn heatsink fan.
Reset the Predictive Maintenance object for heatsink fan elapsed life.
Power down.
Replace the Mn heatsink fan.
Check the ambient temperature.




If alarm persists, replace the balance resistors, the DC bus capacitor assembly, or Mn power module.
Cycle power.
If fault persists, replace the balance resistors, the DC bus capacitor assembly, or Mn power module.
Cycle power.
For the Mn power module with Bit 2 ‘LR OvrTempSw’ set, check the condition of cabinet air filters.
Condition 1: Inspect the bus conditioners and the thermal sensor harness for the exit wiring bay. See the hardware
service manual.
Condition 2: Investigate causes for over-temperature in the wiring bays. Check the enclosure filters and fans. Check the
thermal sensor harnesses for the wiring bays or bypass jumper. See the Service Manual, publication 750-TG100. Check
the Predictive Maintenance parameters for these fans. Check the baffling between the wiring bays and adjacent bays
that may be sources of heat. Problems with the baffling between these bays and adjacent bays can be sources of heat.
If the fault persists, power down and then check the fiber-optic communication connections.
Troubleshoot the customer supplied 24V DC auxiliary power (if used).

Check the cabinet filters for blockage.

Check to see that internal airflow baffles are properly installed.
Check to see that cabinet air filters are properly installed.

Check to see that the cabinet doors are properly closed.
During the next scheduled downtime, replace the Mn heatsink fan and reset the predictive maintenance function for the
fan.
During the next scheduled downtime, replace the Mn power module.

During the next scheduled downtime, replace the Mn DC bus capacitor bank and reset the predictive maintenance
function for the capacitor bank.
During the next scheduled downtime, replace the stirring fans and reset the predictive maintenance function for them.
Disconnect the motor leads at the motor and run the drive.
If the fault is not present, suspect a short circuit in the motor.
If fault persists, suspect a short circuit in the motor leads or Mn power module.
For closed loop systems, verify feedback functionality.
Detune the velocity/position loop bandwidth.
If a mechanical brake is installed, verify its functionality.
If the fault persists, suspect a short circuit in the motor leads or Mn power module.

Replace fiber-optic cables and/or fiber transceiver circuit boards if damaged.
Replace the Mn PIB.

If fault persists, replace the Mn power module.
Verify if DC fuse is open or not.

If DC fuse is ok, investigate DC fuse harness and tellback signal.
If DC fuse is open, investigate why the DC fuse opened. After correction, replace the DC fuse.


Inspect the DCPC module 240V AC supply fuses and connections.
Power down and check the wiring in the DC precharge module.
Verify that the power structure stirring fan is operating.
Verify that the power structure stirring fan or fans are operating.
Verify that the pod fan, if present, is operating.
Verify that the power board wiring harnesses is connected and seated.
—
Power down and verify connections.

Upon power up, the MCB attempts to flash the power peripheral again.
If fault persists, replace the power peripheral.
Power down and verify connections. Upon power up the MCB attempts to flash the power peripheral again.
Power down and verify connections. Upon power up the MCB attempts to flash the power peripheral again.
Power down and verify connections. Power up and rerun DPI flash update
Remove power to the drive.

Replace the drive.

fault.

fault.

fault.






fault.


fault.




— —

— —

fault.
Coast (Motor Side Inverter)
fault.

fault.


— —

— —


— —

— —



— —
— —

— —

— —

fault.

fault.
— —

fault.

fault.

fault.
fault.
— —

— —
— —

— —

— —

— —
— —

— —
— —




— —
— 0:590 [Hi TR EventActn]
— 0:591 [Lo TR EventActn]
— —
— —
— —
— —
fault.

fault.

fault.

fault.

fault.

fault.

fault.


fault.
— 12:40 [DCP CP Low Actn]

— —
— 12:41 [DCP FD1Off Actn]

fault.
Coast (Motor Side Inverter)

— —
— —
— —
— —
— —
— —

Configurable Action
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Ignore
Alarm
—
—
—
—
—
—
—
—
—
—
Ignore
Alarm
Ignore
Alarm
Ignore
Alarm
Ignore
Alarm
Ignore
Alarm
Ignore
Alarm
—
—
—
Ignore
Alarm
Flt Minor
Flt Stop
Ignore
Alarm
Flt Minor
Flt Stop
—
—
Configurable 13001 LnSyncLoss Det Loss of PLL Synchronization Detected
Resettable Fault 13002 LnSyncLoss RTExp Loss of PLL Synchronization Ride

Through Timer Expired
Configurable 13003 Phase Loss Det Input Phase Loss Detected
Configurable 13004 Phase Loss RTExp Input Phase Loss Ride Through Timer
Expired
Configurable 13005 PowerLoss Det Power Loss Detected

Configurable 13006 PowerLoss RTExp Power Loss Ride Through Timer
Expired
Configurable 13007 Line Sag Det Voltage Sag Detected
Configurable 13008 Line Sag RTExp Voltage Sag Ride Through Timer
Expired
Configurable 13009 High df/dt Det High df/dt Detected
Configurable 13010 High df/dt RTExp High df/dt Ride Through Timer
Expired
Alarm 1 13011 LineVltgUnbal Voltage Unbalance
Alarm 1 13012 LineCurUnbal Current Unbalance

Configurable 13013 AC L12 OvrVltg A AC Source Over Voltage-L12 > Over A
Configurable 13016 AC L12 OvrVltg B AC Source Over Voltage-L12 > Over B
Configurable 13019 AC L12 UndrVltgA AC Source Under Voltage-L12 <

Under A
Configurable 13020 AC L23 UndrVltgA AC Source Under Voltage-L23 <
Under A
Configurable 13021 AC L31 UndrVltgA AC Source Under Voltage-L31 >

Under A
Configurable 13022 AC L12 UndrVltgB AC Source Under Voltage-L12 <

Under B

Under B

Under B
Configurable 13025 AC L12 HiVltg A AC Source High Voltage-L12 > High A

Configurable 13028 AC L12 HiVltg B AC Source High Voltage-L12 < High B
Configurable 13029 AC L23 HiVltg B AC Source Under Voltage-L23 < High

B
Configurable 13030 AC L31 HiVltg B AC Source Under Voltage-L31 <

Under B
Configurable 13031 AC L12 LoVltg A AC Source High Voltage-L12 < Low A
Configurable 13032 AC L23 LoVltg A AC Source Under Voltage-L23 < Low

A
Configurable 13033 AC L31 LoVltg A AC Source Under Voltage-L31 < Low

A
Configurable 13034 AC L12 LoVltg B AC Source High Voltage-L12 < Low B
Configurable 13035 AC L23 LoVltg B AC Source Under Voltage-L23 < Low

B
Configurable 13036 AC L31 LoVltg B AC Source Under Voltage-L31 < Low

B
Configurable 13037 AC Line OvrFreqA AC Source Over Frequency - Freq >

Over A
Configurable 13038 AC Line OvrFreqB AC Source Over Frequency - Freq >

Over B
Configurable 13039 AC Ln UndrFreq A AC Source Under Frequency - Freq <

Under A
Configurable 13040 AC Ln UndrFreq B AC Source Under Frequency - Freq <

Under B
Configurable 13041 AC Ln HiFreq A AC Source High Frequency - Freq >
High A
Configurable 13042 AC Ln HiFreq B AC Source High Frequency - Freq >

High B
Configurable 13043 AC Ln LoFreq A AC Source Low Frequency - Freq <

Low A
Configurable 13044 AC Ln LoFreq B AC Source Low Frequency - Freq <

Low B
Resettable Fault 13046 Heatsink OvrTemp Heatsink Over Temperature
Configurable 13047 L Ground Warning Converter Ground Warning
Configurable 13048 HRG Gnd Warn High Resistance Ground Current

Configurable 13049 HRG Gnd Warn Lcl High Resistance Ground Current
Local
Alarm 1 13050 Line Phase Rvs ACB Phase Connection
Alarm 1 13051 Fdbk Data Late Feedback Data Late
Alarm 1 13052 PWM Data Late PWM Data Late

Resettable Fault 13053 HW OverCurrent Hardware Over Current

Resettable Fault 13060 CntrlTask Wtchdg Control Task Watchdog
Resettable Fault 13061 SystmTask Wtchdg System Task Watchdog

Resettable Fault 13065 SW Bus Low Volt Software Bus Low Voltage
Resettable Fault 13066 OverVoltage Over Voltage
Non-Resettable 13067 Cnv App No Strt Converter Application Not Start

Fault
Resettable Fault 13069 R Overload Flt R Overload Fault
Alarm 1 13070 R Overload Alm R Overload Alarm
Resettable Fault 13071 S Overload Flt S Overload Fault
Alarm 1 13072 S Overload Alm S Overload Alarm

Resettable Fault 13073 T Overload Flt T Overload Fault
Alarm 1 13074 T Overload Alm T Overload Alarm
Resettable Fault 13075 Bus Rate of Rise Bus Rate of Rise
Event 13076 LineSide Started Line Side PWM Started
Event 13077 LineSide Stopped Line Side PWM Stopped
Alarm 2 13078 Frame 5 Actv Dmp Frame 5 Active Damping
Resettable Fault 13092 SW OverCurrent Software Over Current

Fault
The line side converter has detected a loss of phase synchronization with
the incoming line.
• The transient phase locked loop (PLL) error exceeded 350% of the value
of parameter 13:192 [BasicPLL Err Lmt]
• The steady state PLL error in parameter 13:88 [Basic PLL Error] exceeded
the value of parameter 13:192 [BasicPLL Err Lmt] for a time that is at least
the value of parameter 13:193 [BasicPLL Err Dly]
• The filtered value for reactive voltage has exceeded the 35% of peak
input line voltage
• A blown fuse in the FD1 fused disconnect can also cause this fault.
The loss of PLL synchronization condition has persisted longer than value
in 13:172 [RideThrough Time].
Input phase loss has been detected for the regenerative power supply
converter:
The magnitude of the average RMS line current is greater than
approximately 20% of its rated value. Also, the magnitude of the sum of
any two phases of the AC line current is less than the minimum threshold
while the converter is modulating.
Or
The difference between 2 of the input line-to-line voltages is less than a
minimum threshold while the converter is stopped.
The converter input-phase loss condition has persisted longer than the
value in parameter 13:172 [RideThrough Time].
The RMS value of all the three line-to-line input voltages is less than 15%
of the value of parameter Rated Volts.
The converter power loss condition has persisted longer than the value in
parameter 13:172 [RideThrough Time].
The difference between the instantaneous value of the input AC line

voltage and a filtered AC line voltage exceeds 50% of the nominal AC line
voltage.
The converter voltage sag condition has persisted longer than the value in
parameter 13:172 [RideThrough Time].
The input AC line frequency rate of change has exceeded 628.3

radians/second (equivalent to 100 Hz/second).
The converter frequency high rate of change condition has persisted

longer than the value in 13:172 [RideThrough Time].
The absolute value of the difference between any AC line voltage (i.e.,
parameter 13:3 [R-S Line Volts], 13:4 [S-T Line Volts], or 13:5 [T-R Line
Volts]) and the total 3-phase average AC line voltage (parameter 13:2 [AC
Line Voltage]) exceeded the value of parameter 13:185 [Line V Unbal Lmt]
for a time at least the value of parameter 13:186 [Line V Unbal Dly].
The absolute value of the difference between any AC line current (i.e.,
parameter 13:9 [R Phase Current], 13:10 [S Phase Current], or 13:11 [T
Phase Current]) and the average measured RMS AC phase current
(parameter 13:6 [AC Line Current]) exceeded the value of parameter
13:188 [Line I Unbal Lmt] for a time at least the value of parameter 13:189
[Line I Unbal Dly].
The value of parameter 13:3 [R-S Line Volts] > (13:119 [Over Volt Lmt A] x
13:25 [Rated Volts]) for a time at least 13:120 [Over Volt Dly A] when
parameter 13:31 [AC Line Source] is set to 0 ‘AC Line A’.
The value of parameter 13:4 [S-T Line Volts] > (13:119 [Over Volt Lmt A] x
The value of parameter 13:5 [T-R Line Volts] > (13:119 [Over Volt Lmt A] x
The value of parameter 13:3 [R-S Line Volts] > (13:133 [Over Volt Lmt B] x
13:25 [Rated Volts]) for a time at least 13:134 [Over Volt Dly B] when
parameter 13:31 [AC Line Source] is set to 1 ‘AC Line B’.
The value of parameter 13:4 [S-T Line Volts] > (13:133 [Over Volt Lmt B] x
The value of parameter 13:5 [T-R Line Volts] > (13:133 [Over Volt Lmt B] x
The value of parameter 13:3 [R-S Line Volts] < (13:110 [Under Volt Lmt A] x
13:25 [Rated Volts]) for a time at least 13:111 [Under Volt Dly A] when
The value of parameter 13:4 [S-T Line Volts] < (13:110 [Under Volt Lmt A] x
13:25 [Rated Volts]) for a time at least 13:120 [Under Volt Dly A] when
The value of parameter 13:5 [T-R Line Volts] < (13:110 [Under Volt Lmt A] x
The value of parameter 13:3 [R-S Line Volts] < (13:124 [Under Volt Lmt B] x
13:25 [Rated Volts]) for a time at least 13:125 [Under Volt Dly B] when
The value of parameter 13:4 [S-T Line Volts] < (13:124 [Under Volt Lmt B] x
The value of parameter 13:5 [T-R Line Volts] < (13:124 [Under Volt Lmt B] x
The value of parameter 13:3 [R-S Line Volts] > (13:119 [High Volt Lmt A] x
13:25 [Rated Volts]) for a time at least 13:117 [High Volt Dly A] when
The value of parameter 13:4 [S-T Line Volts] > (13:119 [High Volt Lmt A] x
The value of parameter 13:5 [T-R Line Volts] > (13:119 [High Volt Lmt A] x
The value of parameter 13:3 [R-S Line Volts] < (13:130 [High Volt Lmt B] x
13:25 [Rated Volts]) for a time at least 13:131 [High Volt Dly B] when
The value of parameter 13:4 [S-T Line Volts] < (13:130 [High Volt Lmt B] x
The value of parameter 13:5 [T-R Line Volts] < (13:130 [High Volt Lmt B] x
The value of parameter 13:3 [R-S Line Volts] < (13:113 [Low Volt Lmt A] x
The value of parameter 13:4 [S-T Line Volts] < (13:113 [Low Volt Lmt A] x
The value of parameter 13:5 [T-R Line Volts] < (13:113 [Low Volt Lmt A] x
The value of parameter 13:3 [R-S Line Volts] < (13:127 [Low Volt Lmt B] x
The value of parameter 13:4 [S-T Line Volts] < (13:127 [Low Volt Lmt B] x
The value of parameter 13:5 [T-R Line Volts] < (13:127 [Low Volt Lmt B] x
The value of parameter 13:1 [AC Line Freq] > (13:30 [Nom Line Freq] +
13:149 [Over Freq Lmt A]) for a time at least 13:150 [Over Freq Dly A]
when parameter 13:31 [AC Line Source] is set to 0 ‘AC Line A’.
The value of parameter 13:1 [AC Line Freq] > (13:30 [Nom Line Freq] x
13:163 [Over Freq Lmt B]) for a time at least 13:165 [Over Freq Dly B]
when parameter 13:31 [AC Line Source] is set to 1 ‘AC Line B’.
The value of parameter 13:1 [AC Line Freq] < (13:30 [Nom Line Freq] -
13:140 [Under Freq Lmt A]) for a time at least 13:141 [Under Freq Dly A]
when parameter 13:31 [AC Line Source] is set to 0 ‘AC Line A’.
The value of parameter 13:1 [AC Line Freq] < (13:30 [Nom Line Freq] -
13:154 [Under Freq Lmt B]) for a time at least 13:155 [Under Freq Dly B]
when parameter 13:31 [AC Line Source] is set to 1 ‘AC Line B’.
The value of parameter 13:1 [AC Line Freq] > (13:30 [Nom Line Frq] +
13:146 [High Freq Lmt A]) for a time at least 13:147 [High Freq Dly A] when
The value of parameter 13:1 [AC Line Freq] > (13:30 [Nom Line Frq] +
13:160 [High Freq Lmt B]) for a time at least 13:161 [High Freq Dly B] when
The value of parameter 13:1 [AC Line Freq] < (13:30 [Nom Line Frq] -
13:143 [Low Freq Lmt A]) for a time at least 13:145 [Low Freq Dly A] when
The value of parameter 13:1 [AC Line Freq] < (13:30 [Nom Line Frq] -
13:157 [Low Freq Lmt B]) for a time at least 13:158 [Low Freq Dly B] when
The value of parameter 13:233 [Heatsnk Temp] is greater than 118 °C for
0.5 seconds.
The ground current has exceeded the level set in 0:423 [L Gnd Warn Lvl].
The high-resistance ground (HRG) ground fault detection function has

detected ground current that exceeds the level in parameter 0:426 [HRG
GF Thresh].
The likely source of the high-resistance ground (HRG) ground current
condition is this drive or bus supply.
Negative phase connection has been detected in the AC line input. This
condition leads to false phase indication in troubleshooting. It does not
affect the operating functions of the line side converter.
The Control Feedback data arrived to the main control board late from the
power layer interface (PLI) circuit board and fiber interface circuit board.
The PWM data arrived late from the main control board.
The input current has exceeded the hardware current limit.

The Control task has failed to complete in the allotted amount of time.
The System task has failed to complete in the allotted amount of time.

time.

time.
time.
An undervoltage condition has occurred.

Bus voltage in parameter 0:3 [DC Bus Volts] has fallen below 80% of the
peak value of 13:21 [ACLineMemory]. (Peak value is the AC voltage
multiplied by √2)

threshold.
The line side converter application failed to start in the DSP.
Parameter 13:228 [R (L1) OL Count] is greater than or equal to 100%.

Possible causes include loads that require too much current and power.
Parameter 13:228 [R (L1) OL Count] is greater than or equal to 50% and

less than 100%.
Parameter 13:229 [S (L2) OL Count] is greater than or equal to 100%.
Parameter 13:229 [S (L2) OL Count] is greater than or equal to 50% and

less than 100%.
Parameter 13:230 [T (L3) OL Count] is greater than or equal to 100%.
Parameter 13:230 [T (L3) OL Count] is greater than or equal to 50% and

less than 100%.
Rate of increase in DC bus voltage during precharge is less than expected.
Possible causes include a short circuit in the DC bus or too much
capacitance is connected to the DC bus. See DRIVES-AT005 for maximum
capacitance values.
The product has started pulse width modulation (PWM) in its line side
power structure(s).
The product has stopped pulse width modulation (PWM) in its line side
power structure(s).
Active damping of resonant frequencies in the product’s LCL capacitor
filter is not supported for this frame.
Line side converter current has exceeded the 1 ms current rating. This
rating is greater than the current rating for 3 seconds and less than the
hardware overcurrent fault level. It is typically 200…250% of the drive
continuous rating.
The transistor Junction Temperature the power module has exceeded the
Fault Temperature (varies by rating).
Possible causes include: loads that require too much current and power,
Action
Check the fuses in the FD1 fused disconnect.

Check line conditions and the configuration of the line side converter control.
Investigate Line Synch Loss (see code 13001) and adjust 13:172 [RideThroughTime]
as needed.
Verify balanced three phase input power.

Monitor input AC sine wave for power disturbance. Address disturbance or use ride
through function if possible.
Investigate Input Phase Loss (see code 13003) and adjust 13:172
[RideThroughTime] as needed.
Verify input voltage is within specification. See 750-TD100.

Investigate Power Loss (See code 13005) and adjust 13:172 [RideThroughTime] as
needed.
Verify input voltage is within specification. See the technical data, publication 750-
TD100.
Investigate Voltage Sag (see code 13007) and adjust 13:172 [RideThroughTime] as
needed.
Investigate High df/dt (see code 13009) and adjust 13:172 [RideThroughTime] as
needed.
—
—
—
—
—
—
—
—
—

the technical data, publication 750-TD100.
—
—
Power down and reconnect the incoming AC power so the phase rotation is positive
—
If starting into a rotating load, turn on flying start with parameter 10:70 [FlyingStart
Mode].
Check the motor and external wiring to the drive output terminals for a shorted
condition.
Check for devices between the drive and motor such as a contactor that may be
changing states while the drive is running.
Clear faults.
If fault persists, rerun firmware update and/or replace the main control board.
See the hardware service manual, publication 750-TG100, for the replacement
procedure.
Clear faults.
procedure.
Clear faults.
procedure.
Clear faults.
procedure.
Clear faults.
procedure.
Clear faults.
If fault persists, remove any unnecessary Option Cards from the drive.
Rerun firmware update and/or replace the main control board.
procedure.
Clear faults.
procedure.
Clear faults.
procedure.
Clear faults.
procedure.
Clear faults.
procedure.
Clear faults.
procedure.
TD100.
Monitor the DC bus voltage in parameter 0:3 [DC Bus Volts] in relation to the DC
bus overvoltage threshold in parameter 0:28 [DCBusThresh Act].
Possible causes include: Configuration of Line Side Converter, configuration of DC
bus regulator, high inertia loads, and fast decel times.
TD100.
Cycle power.
If fault persists, run firmware update and/or replace the main control board.
procedure.
Verify that the drive or bus supply is sized and derated correctly. See the technical
data, publication 750-TD100.
Power down and examine the electrical characteristics of the DC bus and the
equipment that is connected to the DC bus.
Set parameter 13:81 [Actv Dampng Gn] to 0.
If starting into a rotating load, turn on flying start with parameter 10:70 [FlyingStart
Mode].
Check the motor and external wiring to the drive output terminals for a shorted
condition.
Check for devices between the drive and motor such as a contactor that may be
changing states while the drive is running.
Check drive sizing and derating. Check the condition of cabinet air filters.
Configurable 13:181 [PLL LOS Det Actn]

OVRD] bit 0 ‘LS Ctrl Flts’
Stop —
Configurable 13:176 [LSCPhLossDetActn]

Configurable 13:177 [PhsLossRTExpActn]

Configurable 13:170 [PwrLoss Det Actn]

Configurable 13:171 [PwrLossRTExpActn]
Configurable 13:173 [VltgSag Det Actn]

Configurable 13:174 [VltgSagRTExpActn]

Configurable 13:179 [DFDT Det Actn]

Configurable 13:180 [DFDTRdThrExp Actn]

— 13:185 [Line V Unbal Lmt]

13:186 [Line V Unbal Dly]
— 13:188 [Line I Unbal Lmt]

13:189 [Line I Unbal Dly]
Configurable 13:121 [OverVltLmtAActn]


Configurable 13:135 [OverVltLmtBActn]



Configurable 13:112 [UnderVltLmtAActn]


Configurable 13:126 [UnderVltLmtBActn]



Configurable 13:118 [HighVltLmtAActn]


Configurable 13:132 [HighVltLmtBActn]



Configurable 13:115 [LowVltLmtAActn]



Configurable 13:129 [LowVltLmtBActn]


Configurable 13:151 [OverFreqLmtAActn]

Configurable 13:165 [OverFreqLmtBActn]

Configurable 13:142 [UnderFreqLmtAActn]

Configurable 13:156 [UnderFreqLmtBActn]

Configurable 13:148 [HighFreqLmtAActn]
Configurable 13:162 [HighFreqLmtBActn]

Configurable 13:145 [LowFreqLmtAActn]

Configurable 13:159 [LowFreqLmtBActn]

Stop —
Configurable 0:422 [L Gnd Warn Actn]


— 13:40 [Conv Options Cfg] Bit 0

‘PhaseRevAlm’
— —
— —
fault.

fault.

fault.

fault.
fault.

fault.

fault.

fault.

fault.

fault.

fault.
fault.


fault.
— —
fault.

— —

— —
— —

— —
— —
— —


Configurable Action
Ride Thru
Major Fault
Ignore
Type 2 Alarm
Ride Thru
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Ride Thru
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Ride Thru
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Ride Thru
Major Fault
Ignore
Type 2 Alarm
Major Fault
—
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Type 2 Alarm
Major Fault
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
—
—
—
—
—
—
—
—
—
Resettable Fault 14002 ConstantsMsgIvld Constants Message Invalid Fault
Non-Resettable 14003 Constants Chksum Constants Checksum Fault

Fault

Fault
Resettable Fault 14005 Power Supply UV Power Supply Undervoltage
Resettable Fault 14006 Precharge Fault Precharge Fault

Resettable Fault 14007 MCB CL BayOTmp MCB Failed to Close or Wiring Bay
Overtemp
Resettable Fault 14008 MCB Fail To Opn MCB Failed to Open
Resettable Fault 14009 MCB Aux BayOTmp MCB Aux Mismatch or Wiring Bay
Overtemp
Resettable Fault 14010 240VAC Loss Flt 240V AC Loss Fault
Resettable Fault 14011 240VAC OV 240V AC Over Voltage

Resettable Fault 14012 FDOpen MCBClose Fused Disconnect Open (MCB Closed)
Resettable Fault 14013 SysPwr OC Fault SysPwr OC Fault
Resettable Fault 14014 AC Fuse Open AC Fuse Open
Resettable Fault 14016 LEM b0 Flt LEM Present b0 Fault
Resettable Fault 14017 Gate Drive Flt Gate Drive Fault
Resettable Fault 14018 Fiber Offline Fiber Went Offline
Resettable Fault 14019 SysPwr OV Flt SysPwr OV Fault

Resettable Fault 14020 N24V UV Flt Neg 24V Undervoltage Fault
Resettable Fault 14022 Pred NVS Error Predictive Maintenance Non-Volatile

Storage Error
Resettable Fault 14023 CtrlMsgWdog Tout Control Msg Watchdog Timeout
Resettable Fault 14024 CapFailureCfg Capacitor Failure Configuration
Resettable Fault 14025 Incom GateDr Flt Incompatible Gate Drive Fault
Resettable Fault 14026 Ground Flt Ground Fault
Resettable Fault 14027 Bus OV Flt Bus OV Fault

Resettable Fault 14028 NTC-R Short Flt NTC-R Short Fault
Resettable Fault 14029 NTC-R Open Flt NTC-R Open Fault
Resettable Fault 14030 R OverTemp Flt Heatsink-R OverTemp Fault
Alarm1 14031 R OverTemp Alm Heatsink-R OverTemp Alarm
Resettable Fault 14032 R LowTemp Flt Heatsink-R LowTemp Fault
Alarm1 14033 R LowTemp Alm Heatsink-R LowTemp Alarm
Resettable Fault 14034 NTC-S Short Flt NTC-S Short Fault

Resettable Fault 14035 NTC-S Open Flt NTC-S Open Fault
Resettable Fault 14036 S OverTemp Flt Heatsink-S OverTemp Fault
Alarm1 14037 S OverTemp Alm Heatsink-S OverTemp Alarm
Resettable Fault 14038 S LowTemp Flt Heatsink-S LowTemp Fault
Alarm1 14039 S LowTemp Alm Heatsink-S LowTemp Alarm
Resettable Fault 14040 NTC-T Short Flt NTC-T Short Fault
Resettable Fault 14041 NTC-T Open Flt NTC-T Open Fault

Resettable Fault 14042 T OverTemp Flt Heatsink-T OverTemp Fault
Alarm1 14043 T OverTemp Alm Heatsink-T OverTemp Alarm
Resettable Fault 14044 T LowTemp Flt Heatsink-T LowTemp Fault
Alarm1 14045 T LowTemp Alm Heatsink-T LowTemp Alarm
Alarm1 14047 Jnt OverTemp Alm Junction OverTemp Alarm
Resettable Fault 14048 Hw Conflict Flt Rating Hardware Conflict Fault

Resettable Fault 14049 RatingMissingFlt Rating Missing Fault
Resettable Fault 14050 R Overload Flt R Overload Fault
Alarm1 14051 R Overload Alm R Overload Alarm
Resettable Fault 14052 S Overload Flt S Overload Fault
Alarm1 14053 S Overload Alm S Overload Alarm
Resettable Fault 14054 T Overload Flt T Overload Fault
Alarm1 14055 T Overload Alm T Overload Alarm
Resettable Fault 14056 CapOvrRsncCfg Capacitor Over Resonance

Configuration
Resettable Fault 14060 Volt Class Flt Voltage Class Fault
Resettable Fault 14061 Duty Rating Flt Duty Rating Fault
Resettable Fault 14062 Pwr UnitTyp Flt Power Unit Type Fault
Resettable Fault 14063 DTM ConstCorrFlt DTM Constants Corrupted Fault
Alarm1 14064 Main Blower Alm Main Blower Alarm
Resettable Fault 14065 Main Blower Flt Main Blower Fault
Alarm1 14066 Stir Fan 1 Alarm Stir Fan 1 Alarm
Resettable Fault 14067 Stir Fan 1 Fault Stir Fan 1 Fault

Alarm1 14068 Stir Fan 2 Alarm Stir Fan 2 Alarm
Resettable Fault 14069 Stir Fan 2 Fault Stir Fan 2 Fault
Alarm1 14070 Board OT Alarm Board OT Alarm
Resettable Fault 14071 Board OT Fault Board OT Fault
Alarm1 14072 Board UT Alarm Board UT Alarm
Resettable Fault 14073 Board UT Fault Board UT Fault
Alarm1 14074 IntakeAirOT Alrm Intake Air OT Alarm
Resettable Fault 14075 IntakeAir OT Flt Intake Air OT Fault

Alarm1 14076 IntakeAirUT Alrm Intake Air UT Alarm
Resettable Fault 14077 IntakeAir UT Flt Intake Air UT Fault
Alarm1 14078 PIB OT Alarm PIB OT Alarm
Resettable Fault 14079 PIB OT Fault PIB OT Fault
Alarm1 14080 PIB UT Alarm PIB UT Alarm
Resettable Fault 14081 PIB UT Fault PIB UT Fault
Alarm1 14082 Offset Alm Offset Alarm

Alarm1 14083 Bus Imbalanc Alm Bus Imbalance Alarm
Resettable Fault 14084 Bus Imbalanc Flt Bus Imbalance Fault

Resettable Fault 14085 PWM Enable Flt PWM Enable w/o DTM Active Fault
Resettable Fault 14086 L/R Overtemp L/R Overtemp
Resettable Fault 14087 BusCond BayOTmp Bus Conditioner Fault or Wiring Bay
Overtemp
Resettable Fault 14088 Sec Fbk Watchdog Secondary Feedback Watchdog
Alarm1 14089 ISO UV ISO Under Voltage
Resettable Fault 14090 CabAirHiTempRise Cabinet Air High Temperature Rise
Resettable Fault 14091 CabAirLoTempRise Cabinet Air Low Temperature Rise

Configurable 14092 HS Fan Life Heatsink Fan Life Threshold
Exceeded
Configurable 14093 IGBT Life IGBT Life Threshold Exceeded
Configurable 14094 Bus Cap Life Bus Capacitor Life Threshold

Exceeded
Configurable 14095 Stir Fan Life Stirring Fan Life Threshold Exceeded
Resettable Fault 14096 R Pos IOC Flt R Pos IOC Fault
Resettable Fault 14097 S Pos IOC Flt S Pos IOC Fault
Resettable Fault 14098 T Pos IOC Flt T Pos IOC Fault
Resettable Fault 14099 R Neg IOC Flt R Neg IOC Fault
Resettable Fault 14100 S Neg IOC Flt S Neg IOC Fault

Resettable Fault 14101 T Neg IOC Flt T Neg IOC Fault
Resettable Fault 14102 LocPwr UV Flt LocPwr UV Fault
Resettable Fault 14104 P24 UV Flt Pos 24V Undervoltage Fault
Resettable Fault 14107 DC Fuse Open DC Fuse Open
Configurable 14108 240VAC Low 240V AC Low
Alarm 2 14109 240VAC Loss 240V AC Loss

Configurable 14110 FDOpen MCBOpen Fused Disconnect Open (MCB Open)
Resettable Fault 14111 InvalidRatingFlt Invalid Rating Fault
Resettable Fault 14112 Capacitor Fault Capacitor Failure
Alarm 1 14113 Fan Ovrtemp Alm Fan Over Temperature Alarm
Resettable Fault 14114 Fan OverTemp Flt Fan Over Temperature Fault
Alarm 1 14115 Fan UdrTemp Alm Fan Under Temperature Alarm

Resettable Fault 14116 Fan UdrTemp Flt Fan Under Temperature Fault
Alarm 1 14117 CapHighResonance Capacitor High Resonance
Configurable 14118 CapOverResonance Capacitor Over Resonance

Resettable Fault 14119 Reactor OT Fault Reactor Over Temperature Fault
Resettable Fault 14120 PCC Fail To Cls PCC Failed to Close
Resettable Fault 14121 PCC Fail To Opn PCC Failed to Open
Resettable Fault 14122 PCC Aux Mismatch PCC Aux Mismatch
Resettable Fault 14123 MCB Trip Reset MCB Trip Reset
Resettable Fault 14124 MCB Overcurrent MCB Overcurrent

Configurable 14125 LCL FltrCap Life LCL Filter Cap Life Threshold
Exceeded
Resettable Fault 14126 AC Line Ovr Vltg AC Line Over Voltage
Configurable 14127 ACP MCB Life MCB Life Threshold Exceeded
Configurable 14128 ACP PCC Life PCC Life Threshold Exceeded
Configurable 14130 TVSS Open TVSS Open
Alarm1 14131 Flash Timeout HSI Flash Timeout
Alarm1 14132 FlashRst Timeout HSI Flash Reset Timeout
Alarm1 14133 Login Timeout HSI Login Timeout

Alarm1 14134 Flash DPI Error Flash DPI Error
Non-Resettable 14135 BusCapVltgImbal DC Bus Capacitor Voltage Imbalance

Fault
Resettable Fault 14136 Lineside IOC Flt IOC Fault
Alarm 1 14142 Prchrg3 Sec Precharge 3 Second Alarm
Alarm 1 14143 Prchrg30 Sec Precharge 30 Second Alarm

Fault
Communication between the main control board and the image buffer in
one of the power peripherals (power layer interface board, current sense
board, or AC precharge board) has stopped transmitting for 10
milliseconds.
The constants header information did not match the content that one of
the power peripherals (power layer interface board, current sense board,
or AC precharge board) expected.
The constants download failed the checksum test by one of the power
peripherals (power layer interface board, current sense board, or AC
precharge board).
Checksum test failed for non-volatile data for the current sense board or
AC precharge board.
An undervoltage event occurred in the local (internal to the PIB) power

supply.
A possible cause is the DC bus voltage, which feeds the power supply, has
dropped below 400V DC.
This power supply provides power to the power layer interface board or
DC precharge board (if present).
The DC bus voltage was less than the configured threshold 1.5 seconds
after precharge was commanded.
Two things can cause this fault:
The main circuit breaker (CB1) in the AC precharge has failed to close
when commanded.
Or
The temperature in the input bay or entry wiring bay has risen too high.
This condition can only cause the fault before the drive or bus supply has
completed precharge. Investigate causes for over- temperature in these
bays.
Main circuit breaker did not open with 1.5 seconds of being commanded
open.
Two things can cause this fault:

The auxiliary contact on the main circuit breaker (CB1) in the AC precharge
is not functioning properly.
Or
The temperature in the input bay or entry wiring bay has risen too high.
This condition can only cause the fault after the drive or bus supply has
completed precharge. Investigate causes for over- temperature in these
bays.
The 240V AC supply voltage fell below the specified minimum voltage level
of 154V AC during the pre-charge cycle or while the main circuit breaker
(MCB) is closed.
See parameters 14:1112 [ACP0 PwrSup Vltg] and/or 14:1122 [ACP1
PwrSup Vltg].
The 240V AC supply voltage rose above the specified maximum voltage
level (283V AC).
PwrSup Vltg].
Fused Disconnect Open (MCB Closed)
Fused disconnect (FD1) open detected when the main circuit breaker
(MCB) was closed.
An over current event occurred in the local (internal to the PIB) power
supply. It affects the operation of the positive 24V power supply.
The most likely cause is a component failure in the Ln PIB, ACPC, or power
module.
An AC fuse that connects power to the input of an LCL filter has cleared.
Not all LEM current sensors are connected and operating.
A Gate Drive Board fault has occurred.

Possible causes include an internal power supply failure (if the fault
occurred before the drive or bus supply was enabled), or an IGBT
desaturation (over temperature or over current) event.
The fiber-optic communication link between the fiber interface circuit

board and one of the power peripherals (power layer interface board,
current sense board, or AC precharge board) transitioned from online to
offline.
Frames 7…15: An overvoltage event occurred in the local (internal to the

PIB) power supply. It affects the operation of the positive 24V power
supply.
Frames 5 and 6: An overvoltage or undervoltage event occurred in the
local power supply.
The most likely cause is the 24V DC supply power input is below the -1%
power input threshold of 23.76V
supply. It affects the operation of the negative 24V power supply.
Data from Electronically Erasable Read Only Memory (EEROM) on the

power board or AC precharge board of a power module within the line
side converter is corrupt.
The watchdog timer for transmission of the Control Message between the
main control board and one of the power peripherals (power layer
interface board or current sense board) has timed-out.
The response to the LCL filter capacitor failure condition has been
configured as alarm, but the risks to equipment have not been read and
understood.
An incompatible Gate Drive Board is installed.
Power layer interface (PLI) hardware in the power module has detected a
ground fault event.
Ground current is greater than 25% of the power module rating.

threshold.
The heatsink temperature sensor (NTC) for the R (L1) phase of the power
The sensor or circuit is faulty. See the corresponding parameter in port 14
[Ln HeatsinkTempR].
The heatsink temperature sensor (NTC) for the R (L1) phase of the power
[Ln HeatsinkTempR].
The temperature in the heatsink for the R (L1) phase of the power module
See the corresponding parameter in port 14 [Ln HeatsinkTempR].
See the corresponding parameter in port 14 [Ln HeatsinkTempR].
has fallen below -30 °C.
operation. See the corresponding parameter in port 14 [Ln
HeatsinkTempR].
HeatsinkTempR].
The heatsink temperature sensor (NTC) for the S (L2) phase of the power
[Ln HeatsinkTempS].
The heatsink temperature sensor (NTC) for the S (L2) phase of the power
[Ln HeatsinkTempS].
The temperature in the heatsink for the S (L2) phase of the power module
See the corresponding parameter in port 14 [Ln HeatsinkTempS].
See the corresponding parameter in port 14 [Ln HeatsinkTempS].
HeatsinkTempS]
HeatsinkTempS].
The heatsink temperature sensor (NTC) for the T (L3) phase of the power
[Ln HeatsinkTempT].
The heatsink temperature sensor (NTC) for the T (L3) phase of the power
[Ln HeatsinkTempT].
The temperature in the heatsink for the T (L3) phase of the power module
See the corresponding parameter in port 14 [Ln HeatsinkTempT].
See the corresponding parameter in port 14 [Ln HeatsinkTempT].
HeatsinkTempT].
HeatsinkTempT].
The transistor junction temperature of the power module has exceeded

the Fault Temperature which is 155 °C for 3.5 sec or 165 °C.
See the corresponding parameter in port 14 [Ln IGBT Temp] Note: This
temperature may rise/fall faster than the update rate of the drive.
The transistor junction temperature of the power module has exceeded

the alarm temperature which is 155 °C.
See the corresponding parameter in port 14 [Ln IGBT Temp] Note: This
temperature may rise/fall faster than the update rate of the drive.
Current sense board (CSB) ID Current rating does not agree with Constants
Current rating.
The rating plug is not properly installed on the current sense board (CSB).
The Current Overload Count for the R (L1) phase has exceeded 100%.
The Current Overload Count for the R (L1) phase has exceeded 50%.
The Current Overload Count for the S (L2) phase has exceeded 100%.
The Current Overload Count for the S (L2) phase has exceeded 50%.
The Current Overload Count for the T (L3) phase has exceeded 100%.
The Current Overload Count for the T (L3) phase has exceeded 50%.
The response to the LCL filter capacitor over-resonance condition has been
configured as alarm, but the risks to equipment have not been read and
understood.
The voltage class that is programmed in the power module is incorrect or
corrupt.
The duty rating that is programmed in the power module is incorrect or

corrupt.
The power unit type that is programmed in the power module is incorrect
or corrupt.
Runtime Constants data corruption detected.
The Ln or Fnx heatsink fan is running below the alarm threshold speed.
If the line side converter is not modulating, this alarm occurs when the Ln
or Fn heatsink fan speed is below 120 RPM.
If the line side converter is modulating, this alarm occurs when the Ln or
Fn heatsink fan speed is below 2050 RPM.
The Ln or Fn heatsink fan is running below the fault threshold speed.

If the line side converter is not modulating, this fault occurs when the Ln
or Fn heatsink fan speed is below 60 RPM.
If the line side converter is modulating, this fault occurs when the Ln or Fn
heatsink fan speed is below 1800 RPM.
The stirring fan 1 (parameter 14:148 [L0 St Fan 1 Spd]) is running below
the alarm threshold speed (9570 RPM). Only applicable to frames 5 and 6.
the fault threshold speed (9350 RPM). Only applicable to frames 5 and 6.
the alarm threshold speed (9570 RPM). Only applicable to frames 5 and 6.
the fault threshold speed (9350 RPM). Only applicable to frames 5 and 6.

board, current sense board, or AC precharge board) has exceeded the
Alarm Temperature (75 °C).
See the corresponding parameter in port 14 [Ln PLI BoardTemp], [Fx CSB
BoardTemp], and/or [ACPn Board Temp]

board, current sense board, or AC precharge board) has exceeded the fault
temperature (80 °C).
See the corresponding [Ln PLI BoardTemp], [Fn CSB BoardTemp], and/or
[ACPn Board Temp] parameter in port 14.

board, current sense board, or AC precharge board) has fallen below the
alarm temperature (-25 °C).
[Ln PLI BoardTemp], [Fn CSB BoardTemp], and/or [ACPn Board Temp]
parameter in port 14.

board, current sense board, or AC precharge board) has fallen below the
fault temperature (-30 °C).
[Ln PLI BoardTemp], [Fn CSB BoardTemp], and/or [ACPn Board Temp]
parameter in port 14.
Power module intake air has exceeded the alarm temperature (60 °C). See
the corresponding parameter in port 14 [Ln Meas Amb Tmp].
Power module intake air has exceeded the fault temperature (70 °C). See
Power module intake air has fallen below the alarm temperature (- 10 °C).
See the corresponding parameter in port 14 [Ln Meas Amb Tmp].
Power module intake air has fallen below the fault temperature (-25 °C).
The power interface board (PIB) has exceeded the alarm temperature (75
°C).
See the corresponding parameter in port 14 [Ln PIB BoardTemp].
The power interface board (PIB) has exceeded the fault temperature (80
°C).
The power interface board (PIB) has fallen below the alarm temperature (-
25 °C).
The power interface board (PIB) has fallen below the fault temperature (-
30 °C).
See the corresponding parameter in port 14 [Ln PIB BoardTemp]
Control has detected excessive DC offset.

The DC bus voltage imbalance between Mn power modules has exceeded
the alarm threshold. See the corresponding parameter in port 14 [Ln DC
BusVoltage].
The DC bus voltage imbalance between Mn Power modules has exceeded

the fault threshold. See the corresponding parameter in port 14 [Ln DC
BusVoltage].
Control attempted to modulate before the thermal manager was running.
An over temperature event has occurred in the parallel inductor or dv/dt

filter. High temperature caused the thermal switch to open. Check cabinet
filters, heatsink fans, intake air temperatures, and the baffles that help
prevent recirculation of heated air. See the corresponding diagnostic item
in port 14 [LnStatusWord] Bit 2 ‘LR OT Swth’
Two conditions can cause this fault in a frame 8 or larger drive or CBI:
Condition 1: A bus conditioner is not functioning properly.
Condition 2: High temperature in the optional exit wiring bay can only
cause the fault in the last motor side inverter power module. For example,
in a frame 9 drive that is M1, or in a frame 11 drive that is M3. If the fault
occurs in a power module that is not the last motor side inverter power
module, the cause must be a bus conditioner. If the fault occurs in a power
module that is part of the line side converter, the cause must be a bus
conditioner.
Transmission of the feedback message (PDI fiber-optic cable connection

on the Ln power layer interface (PLI) circuit board) from the current sense
board (CSB) in the LCL filter has timed out.
An undervoltage event occurred in the local (internal to the Mn PIB board)

power supply.
Possible causes include low voltage on the customer-supplied 24V DC
auxiliary power (if used) or component failure.
The High Temperature Rise function has detected an event when the
temperature in the power module has risen higher than expected for the
load and ambient temperature.
The condition must be present for ten minutes for this alarm to occur.
Possible causes include blocked cabinet filters and improper internal
airflow.
The Low Temperature Rise function has detected an event when the
temperature in the power module has failed to rise as expected for the
load and ambient temperature.
Possible causes include missing cabinet filters or open doors.
Elapsed life of the heatsink fan has exceeded the configured event
threshold.
Elapsed life of a power module IGBT has exceeded the configured event
threshold.
Elapsed life of a power module DC bus capacitor bank has exceeded the
configured event threshold.
Elapsed life of the stirring fans has exceeded the configured event
threshold.
The Ln power layer interface (PLI) hardware in the power module has
detected an instantaneous over current (IOC) event on the positive side of
the R (L1) input phase.
the S (L2) input phase.
the T (l3) input phase.
detected an instantaneous over current (IOC) event on the negative side
of the R (L1) input phase.
of the S (L2) input phase.
of the T (L3) input phase.
An undervoltage event occurred in the local (internal to the Ln PIB) power

supply. It affects the operation of the positive or negative 12V power
supply.
One of the power peripherals (power layer interface board, current sense
board, or AC precharge board) has stopped transmitting messages to the
main control board.

supply. It affects the operation of the positive 24V power supply.
A DC fuse that connects the output of the Ln power module to the DC bus
has cleared.
The 240V AC supply voltage is between 154V AC and 187V AC.

PwrSup Vltg].
The 240V AC supply voltage fell below the specified minimum voltage level
of 154V AC while the main circuit breaker (MCB) is opened.
PwrSup Vltg].
Firmware detected the fused disconnect (FD1) opened when the main
circuit breaker (MCB) was open.
The rating plug on the current sense board (CSB) does not match the
hardware in the LCL filter.
Filter capacitor voltages or currents have exceeded control limits.
Power module intake air has exceeded the alarm temperature (60 °C). See
the corresponding parameter in port 14 [Ln Meas Amb Tmp]
Power module intake air has exceeded the fault temperature (70 °C). See
Power module intake air has fallen below the alarm temperature (-10 °C).
Power module intake air has fallen below the fault temperature (-25 °C).
The LCL filter capacitor current harmonic content in the range of resonant
frequencies is greater than the alarm level associated with the product’s
current rating.
The LCL filter capacitor current harmonic content in the range of resonant
frequencies is greater than the fault level associated with the product’s
current rating.
An over temperature event has occurred in the reactor of the LCL filter.
High temperature caused the thermal switch to open.
The precharge contactor (PCC) did not close within 1.5 seconds of being
commanded.
The precharge contactor (PCC) did not open with 1.5 seconds of being
commanded.
The auxiliary contact for the precharge contactor (PCC) is not functioning
properly.
The main circuit breaker (MCB) bell alarm switch (an indication for over
current) could not be reset.
The main circuit breaker (MCB) opened due to over current (MCB bell
alarm).
Elapsed life of LCL filter capacitor has exceeded threshold in parameter
0:586 [LCLCap EventLvl].
The voltage of the incoming AC line exceeded the maximum.
Elapsed life of the main circuit breaker(MCB) has exceeded the threshold
in parameter 0:578 [MCB Life EvntLvl].
Elapsed life of the precharge contactor (PCC) has exceeded the threshold
in parameter 0:582 [PCC Life EvntLvl].
The transient voltage surge suppressor (TVSS) has cleared.
A Flash time-out occurred between one of the power peripherals (power

layer interface board, current sense board, or AC precharge board) and the
main control board during a firmware update.
A Flash reset time-out occurred between one of the power peripherals

(power layer interface board, current sense board, or AC precharge board)
and the main control board during a firmware update.
One of the power peripherals (power layer interface board, current sense
board, or AC precharge board) has failed to log in with the main control
board after a firmware update.
A Flash DPI error has occurred in one of the power peripherals (power
layer interface board, current sense board, or AC precharge board) during
a firmware update.
The voltage of one or more DC bus capacitors has exceeded its surge
rating: 450V DC for 400/480V AC products or 625V DC for 600/690V AC
products. This condition indicates that there is an increased risk of short
circuit.
This condition is only applicable to frames 5 and 6 air-cooled PowerFlex
755TR drives, 755TL drives, and 755TM bus supplies and frame 6L liquid-
cooled 755TR drives.
Lineside hardware in the power module has detected an Instantaneous

Over Current (IOC) event.
During precharge, the DC bus voltage did not rise to 85% of the nominal
level within 3.0 seconds.
This alarm persists until the next precharge.
Large external capacitances or loads on the DC bus are preventing

completion of AC precharge or AC line conditions are preventing
synchronization of the line side converter to the AC line.
This alarm persists until the next precharge.
Action
Cycle power.
Cycle power.
Cycle power.
If the fault persists, replace the current sense board or AC precharge board.
procedure.
Verify DC bus is present on the Lx power module via the hardware testpoints. If so,
replace the Ln PIB.
procedure.
Ensure the converter is properly sized for the application. Verify total external bus
capacitance does not exceed specification. See publication DRIVES-AT005.
Check the Predictive Maintenance parameters for the MCC.
Or
Check the thermal sensor harness for the input bay or entry wiring bay or bypass
jumper.
See the Service Manual, publication 750- TG100, for the replacement procedure.
Check the Predictive Maintenance parameters for these fans.
Inspect the functionality of the main circuit breaker. Check feedback signals to ACPC
board

Check the thermal sensor harness for the input bay or entry wiring bay or bypass
jumper.
See the Service Manual, publication 750- TG100, for procedure.

If configured with a control transformer:
• Inspect connections.
• Inspect primary and secondary fuses.
• Verify that the primary transformer connections are tapped for the proper input
voltage.
See the hardware service manual, publication 750-TG100, for the system schematics.

If configured with a control transformer, verify that the primary transformer
connections are tapped for the proper input voltage.
Close the fused disconnect.
Inspect fused disconnect auxiliary contact to AC precharge board.
If fault persists, replace the AC Prechage board.
See the hardware service manual, publication 750-TG100, for procedures.
Replace failed component.
Power down.
Verify fuse is cleared.
See the hardware service manual, publication 750-TG100.
Replace all AC fuses that connect power to the input of the LCL filter.
Check internal connection harnesses.

Replace LEM (Current sensing device) on frame 8 and higher or the power interface
board or replace Ln power module.
procedure.
Inspect status indicators on the power layer interface (PLI) circuit board.
Replace the Ln power module.
procedure.
Clear faults.
If the fault persists, power down and then check the fiber-optic communication
connections.
Inspect status indicators on Ln power layer interface (PLI) circuit board.

Replace the Ln power module or the power interface board (PIB).
procedure.
Replace the Ln power module or the power interface board (PIB).
procedure.
Cycle power.
If fault persists, replace the Ln power module.
procedure.

procedure.
Read the attention statement under the heading Configurable LCL Filter Capacitor
Failure Response. See the Troubleshooting section of the programming manual,
publication 750-PM101.
Inspect the status indicators on Ln power layer interface (PLI) circuit board.
procedure.
Monitor the DC bus voltage in parameter 0:3 [DC Bus Volts] in relation to the DC bus
overvoltage threshold in parameter 0:28 [DCBusThresh Act].
Possible causes include: Configuration of Line Side Converter, configuration of DC bus
regulator, high inertia loads, and fast decel times.
For regenerative converters, verify the regeneration configuration parameters.
For non-regenerative converters, increase decel time or provide a means to dissipate
excess energy.
procedure.

procedure.

Verify adequate airflow and the ambient temperature is within specification. See the
technical data, publication 750-TD100.

publication 750-TD100.

procedure.
procedure.



procedure.

procedure.


Verify converter configuration for proper transformer nameplate data and gains.

Verify converter configuration for proper transformer nameplate data and gains.
Power down.
Check the installation of the rating plug on the CSB.
If fault persists, replace the CSB.
]See the hardware service manual, publication 750-TG100, for the replacement
procedure.






Read the attention statement under the heading Configurable LCL Filter Capacitor
Over Resonance Response.
See the Troubleshooting section of the programming manual, publication 750-PM101.
Cycle power.
If the fault persists, replace the Ln power interface board (PIB) or the Ln power
module.
procedure.
Cycle power.
module.
procedure.
Cycle power.
module.
procedure.
Clear the fault.

If the fault persists, cycle power and/or replace the power layer interface (PLI) circuit
board.
procedure.
Power down.
Replace the Ln or Fn heatsink fan.
procedure.
Power down.
Replace the Ln or Fn heatsink fan.
procedure.
Investigate slow stirring fan speed.

Replace fan power supply board or stirring fan if needed.
procedure.

procedure.
procedure.

procedure.






If alarm persists, replace the balance resistors,

the DC bus capacitor assembly, or Ln power module.
procedure.
Cycle power.
If fault persists replace the balance resistors, the DC bus capacitor assembly, or Ln
power module.
procedure.
Cycle power.
Condition 1: Inspect the bus conditioners and the thermal sensor harness for the exit
wiring bay. See the Hardware Service Manual, publication 750-TG100 for PowerFlex
755T or publication 750-TG101 for PowerFlex 755TS products, for details.
Condition 2: Investigate causes for over-temperature in the wiring bays. Check the
enclosure filters and fans. Check the thermal sensor harnesses for the wiring bays or
bypass jumper. See the Service Manual, publication 750-TG100. Check the Predictive
Maintenance parameters for these fans. Check the baffling between the wiring bays
and adjacent bays that may be sources of heat. Problems with the baffling between
these bays and adjacent bays can be sources of heat.
If the fault persists, power down and then check the fiber-optic communication
connections.
Troubleshoot the customer-supplied 24V DC auxiliary power (if used).

procedure.
Check the cabinet filters for blockage.

Check to see that internal airflow baffles are properly installed.
Check to see that cabinet air filters are properly installed.

Check to see that the cabinet doors are properly closed.
During the next scheduled downtime, replace the heatsink fan and reset the
predictive maintenance function for the fan.
procedure.
During the next scheduled downtime, replace the Ln power module.
During the next scheduled downtime, replace the DC bus capacitor bank and reset the
predictive maintenance function for the capacitor bank.
Or, replace the Ln power module.
procedure.
During the next scheduled downtime, replace the stirring fans and reset the predictive
maintenance function for the fans.
procedure.

procedure.

procedure.

procedure.

procedure.

procedure.
procedure.

procedure.

Replace fiber-optic cables and/or fiber transceiver circuit boards if damaged.
procedure.
Replace the Ln PIB.

If fault persists, replace the Ln power module.
procedure.
Verify if DC fuse is open or not.

If DC fuse is ok, investigate DC fuse harness and tellback signal.
If DC fuse is open, investigate why the DC fuse opened. After correction, replace the
DC fuse.
See the hardware service manual, publication 750-TG100, for procedures.

If configured with a control transformer, verify that the primary transformer
connections are tapped for the proper input voltage.

If configured with a control transformer,
• Inspect connections and primary and secondary fuses.
• Verify that the primary transformer connections are tapped for the proper input
voltage.
Close the fused disconnect.
Inspect fused disconnect auxiliary contact to AC precharge board.
If fault persists, replace the AC Prechage board.
procedure.
Replace the CSB or LCL filter module.

procedure.
Power down the drive or bus supply.

Replace the LCL filter capacitor. See the hardware service manual, publication 750-
TG100, for the replacement procedure.
Power up the drive or bus supply.
Clear the fault:
• If the power to a frame 5 or 6 drive or a frame 6 bus supply was cycled five times,
you must connect a 24V DC auxiliary power supply to power the control circuits.
• Note the five-digit code that is generated in parameter 14:1205 [F0 CapFltResCode]
and enter it in parameter 14:1206 [F0 CapFltClrCode] to acknowledge that the
capacitor was replaced and to clear the fault.
Reset the predictive maintenance function for the LCL filter capacitor.
Verify proper line side converter configuration and tuning.


Review practices for sizing and locating transformers in publications 750-IN100,

Installation Instructions for PowerFlex 750-Series Products with TotalFORCE Control
and DRIVES-AT005, Drives in Common Bus Configurations with PowerFlex 755TM Bus
Supplies.
If this event occurs while the Line Side Converter is modulating, then the configuration
and tuning of the Line Side Converter can cause the resonance. Consider reducing the
bandwidth of voltage and current regulators. See parameters 13:55 [Volt Reg BW],
13:75 [Curr Reg BW], and 13:300 [BusDistRej Mode].
If this event occurs while the Line Side Converter is not modulating, then equipment
that shares the source of AC power can cause the resonance. Consider changing the
power distribution scheme. Consider installing a form of magnetic isolation such as an
transformer. Also consider using the Energy Pause function to disconnect the Line Side
Converter from the AC source when not needed.
Power down, then replace the filter capacitor.

See the PowerFlex 750-Series Products with TotalFORCE Control Hardware Service
Manual, publication 750-TG100, for the replacement procedure.
Then reset the filter capacitor life parameter.
Review practices for sizing and locating transformers in publications 750-IN100,
Installation Instructions for PowerFlex 750-Series Products with TotalFORCE Control
and DRIVES-AT005, Drives in Common Bus Configurations with PowerFlex 755TM Bus
Supplies.
If this event occurs while the Line Side Converter is modulating, then the configuration
and tuning of the Line Side Converter may be causing the resonance. Consider
reducing the bandwidth of voltage and current regulators. See parameters 13:55 [Volt
Reg BW], 13:75 [Curr Reg BW], and 13:300 [BusDistRej Mode].
If this event occurs while the Line Side Converter is not modulating, then equipment
that shares the source of AC power can cause the resonance. Consider changing the
power distribution scheme. Consider installing a form of magnetic isolation such as an
transformer. Also consider using the Energy Pause function to disconnect the Line Side
Converter from the AC source when not needed.
Check cabinet filters, heatsink fans, intake air temperatures, and the baffles that help
prevent recirculation of heated air.
Power down and check the wiring in the AC precharge module.

If wiring is correct and fault reoccurs, replace the precharge contactor.
procedure.
Then reset the PCC elapsed life parameter.

procedure.

procedure.
Cycle power.
If fault persists, replace the CB1 main circuit breaker.
procedure.
During the next scheduled downtime, replace the filter capacitor.
Or, replace the LCL filter module.
procedure.
Then reset the filter capacitor life object.
Verify input voltage is within specification. See 750-TD100.
During the next scheduled downtime, replace the main circuit breaker.
procedure.
Then reset the MCB life object.
During the next scheduled downtime, replace the precharge contactor.

procedure.
Then reset the PCC life parameter.
Power down.
Investigate causes of high voltage transients spikes on the incoming power.
Replace the transient voltage surge suppressor.
procedure.

Upon power up the MCB attempts to flash the power peripheral again.
procedure.

procedure.

procedure.
Power down and verify connections. Power up and rerun DPI flash update
Power down.
Disconnect the AC line input from the product.
Inspect and replace the failed DC bus capacitor(s).

procedure.
Check external capacitances and loads on the DC bus.

Ensure the external bus capacitance does not exceed the rating of the line side
converter. See the common bus application techniques, publication DRIVES-AT005
Check external capacitances and loads on the DC bus.

Ensure the external bus capacitance does not exceed the rating of the line side
converter. See the common bus application techniques, publication DRIVES-AT005.

fault.

fault.

fault.






fault.

fault.


fault.




N/A (Line Side Converter) —

fault.


fault.

fault.

fault.

fault.


— —

— —


— —

— —


— —

— —

— —

fault.
fault.

— —

— —

— —

fault.
fault.

fault.

fault.

fault.
— —

— —
— —
— —
— —
— —

— —

— —

— —

— —

— —

— —
— —




— —
— 0:590 [Hi TR EventActn]
— 0:591 [Lo TR EventActn]

— —
— —
— —
— —

fault.

fault.

fault.

fault.

fault.
fault.


fault.


fault.
Configurable 14:1132 [ACP CP Low Actn]

— —
Configurable 14:1130 [ACP FD1 Off Actn]
fault.

fault.

fault.
— —

— —
— —
Coast (Motor Side Inverter) 0:453 [CapOvrRsncActn]

fault.

fault.


fault.

fault.

fault.
— —

— —
— —
— —
Configurable 14:1131 [ACP TVSS Action]

— —
— —
— —
— —

fault.

fault.
— —
— —
Configurable Action
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Ignore
Alarm
Ignore
Alarm
Ignore
Alarm
Ignore
Alarm
Ignore
Alarm
Ignore
Alarm
—
—
Ignore
Alarm
Flt Minor
Flt Stop
—
Ignore
Alarm
Flt Minor
Flt Stop
—
—
Alarm
Flt Stop
—
—
Ignore
Alarm
Ignore
Alarm
Ignore
Alarm
Ignore
Alarm
Flt Minor
Flt Stop
N/A
—
—
—
Condition Type Fault Code Display Text
0 No Entry
Configurable nn001 Analog In0 Loss Analog Input 0 Loss
Configurable nn002 Analog In1 Loss Analog Input 1 Loss
Configurable nn005 Relay0 Life Relay 0 Life
Configurable nn006 Relay1 Life Relay 1 Life
Non-Resettable nn010 Anlg Cal Chksum Analog Cal Checksum

Fault
Configurable nn011 PTC Over Temp PTC Over Temperature

Configurable nn012 PTC ShortCircuit PTC Short Circuit
Resettable Fault nn013 ATX Voltage Loss ATX Voltage Loss
Resettable Fault nn014 ThermostatOvrTmp Thermostat Over Temperature
Resettable Fault nn015 ATEX Safety ATEX Safety
Resettable Fault nn999 System Comm Loss System Communication Loss
Resettable Fault nn999 Bkplane Comm Backplane Communication loss
Non-Resettable nn086 HW Enbl Jmpr Out Hardware Enable Jumper Not

Fault Installed
Non-Resettable nn088 Safety Jmpr Out Safety Jumper Not Installed
Fault
Non-Resettable nn089 Safety Jumper In Safety Jumper Installed

Fault
Non-Resettable nn092 SafetyHealth Err Safety Health Error

Fault
Resettable Fault nn093 SafetyPwrOn Err Safety Vcc On
Resettable Fault nn094 SafetyPwrOff Err Safety Vcc Off
Resettable Fault nn004 Safety Fdbk CIP Safety Feedback

Resettable Fault nn005 STO Fault Safety Safe Torque Off Fault
Resettable Fault nn008 Critical Flt Safety Guard Internal Fault
Resettable Fault nn009 MP Out Flt Safety Guard Gate Drive Fault
Resettable Fault nn010 SS In Flt Safety Guard Stop Fault
Configurable nn000 Open Wire Loss Open Wire Loss
Configurable nn001 Phase Loss Phase Loss

Configurable nn002 Quad Loss Quadrature Loss
Configurable nn034 Pri VelFdbk Loss Primary Velocity Feedback Loss
Configurable nn035 Alt VelFdbk Loss Alternate Velocity Feedback Loss
Configurable nn036 Aux VelFdbk Loss Auxiliary Velocity Feedback Loss
Configurable nn037 Pri PsnFdbkLoss Primary Position Feedback Loss
Configurable nn038 Alt PsnFdbkLoss Alternate Position Feedback Loss
Configurable nn999 Bkplane Comm Backplane Communication Loss

Configurable nn000 Enc0 Open Wire Encoder 0 Open Wire
Configurable nn001 Enc0 Phase Loss Encoder 0 Phase Loss
Configurable nn002 Enc0 Quad Loss Encoder 0 Quadrature Loss
Configurable nn030 Enc1 Open Wire Encoder 1 Open Wire
Configurable nn031 Enc1 Phase Loss Encoder 1 Phase Loss
Configurable nn032 Enc1 Quad Loss Encoder 1 Quad Loss

Configurable nn999 Bkplane Comm Backplane Communication Loss
Configurable nn000 Ch0 LightSrc Err Channel 0 Light Source Error
Configurable nn001 Ch0 SigAmp Err Channel 0 Signal Amplitude Error

Configurable nn002 Ch0 PsnVal Err Channel 0 Position Value Error
Configurable nn003 Ch0 OverVolt Err Channel 0 Overvoltage Error
Configurable nn004 Ch0 UndVolt Err Channel 0 Undervoltage Error
Configurable nn005 Ch0 OverCur Err Channel 0 Overcurrent Error
Configurable nn006 Ch0 Battery Err Channel 0 Battery Error
Configurable nn009 Ch0 AnalSig Err Channel 0 Analog Signal Error
Configurable nn010 Ch0 IntOfst Err Channel 0 Interface Offset Error

Configurable nn011 Ch0 DataTabl Err Channel 0 Data Table Error
Configurable nn012 Ch0 AnalLim Err Channel 0 Analog Limit Error
Configurable nn013 Ch0 Int I2C Err Channel 0 Internal I2C Error
Configurable nn014 Ch0 IntChksm Err Channel 0 Internal Checksum Error
Configurable nn015 Ch0 PrgmResetErr Channel 0 Program Reset Error
Configurable nn016 Ch0 CntOvrflwErr Channel 0 Counter Overflow Error
Configurable nn017 Ch0 Parity Err Channel 0 Parity Error

Configurable nn018 Ch0 Chksum Err Channel 0 Checksum Error
Configurable nn019 Ch0 InvCmd Err Channel 0 Invalid Command Error
Configurable nn020 Ch0 SendSize Err Channel 0 Send Size Error
Configurable nn021 Ch0 CmdArgmt Err Channel 0 Command Argument Error
Configurable nn022 Ch0 InvWrtAdrErr Channel 0 Invalid Write Address Error
Configurable nn023 Ch0 AccCode Err Channel 0 Access Code Error
Configurable nn024 Ch0 FieldSizeErr Channel 0 Field Size Error

Configurable nn025 Ch0 Address Err Channel 0 Address Error
Configurable nn026 Ch0 FieldAcc Err Channel 0 Field Access Error
Configurable nn028 Ch0 SiTurnPsnErr Channel 0 Single Turn Position Error
Configurable nn029 Ch0 MulTrnPsnErr Channel 0 Multiple Turn Position

Error
Configurable nn036 Ch0 AnalVal Err Channel 0 Analog Value Error
Configurable nn037 Ch0 SendCurr Err Channel 0 Send Current Error
Configurable nn038 Ch0 EncTemp Err Channel 0 Encoder Temperature

Error
Configurable nn039 Ch0 Speed Err Channel 0 Speed Error
Configurable nn040 Ch0 General Err Channel 0 General Error
Configurable nn046 Ch0 LED Curr Err Channel 0 LED Current Error
Configurable nn047 Ch0 ExMulTurnErr Channel 0 External Multi-Turn Error
Configurable nn048 Ch0 PsnCode Err Channel 0 Position Code Error
Configurable nn049 Ch0 Config Err Channel 0 Configuration Error
Configurable nn050 Ch0 PsnVal Err Channel 0 Position Not Valid Error
Configurable nn051 Ch0 SerialComErr Channel 0 Serial Communication
Error
Configurable nn052 Ch0 Ext Failure Channel 0 External Failure
Configurable nn053 Ch0 Temp Exc Err Channel 0 Temperature Exc Error
nn058 Module Defaulted Module Defaulted
Configurable nn064 Ch0 OutOfRailErr Channel 0 Out Of Rail Error
Configurable nn068 Ch0 Read Head 1 Channel 0 Read Head 1
Configurable nn070 Ch0 RAM Error Channel 0 RAM Error

Configurable nn071 Ch0 EPROM Error Channel 0 EPROM Error
Configurable nn072 Ch0 ROM Error Channel 0 ROM Error
Configurable nn074 Ch0 No Position Channel 0 No Position
Configurable nn081 Ch0 Msg Cheksum Channel 0 Message Checksum
Configurable nn082 Ch0 Timeout Channel 0 Timeout
Configurable nn083 Ch0 Comm Channel 0 Communications
Configurable nn084 Ch0 Diagnostic Channel 0 Diagnostic

Configurable nn085 Ch0 SpplyVltgRng Channel 0 Supply Voltage Range
Configurable nn086 Ch0 SC Amplitude Channel 0 SC Amplitude
Configurable nn087 Ch0 Open Wire Channel 0 Open Wire
Configurable nn088 Ch0 Quad Loss Channel 0 Quadrature Loss
Configurable nn089 Ch0 Phase Loss Channel 0 Phase Loss
Configurable nn090 Ch0 Unsupp Enc Channel 0 Unsupported Encoder
Alarm 1 nn100 Ch0 FreqExc Alm Channel 0 Frequency Exceeded

Alarm
Alarm 1 nn101 Ch0 TempExc Alm Channel 0 Temperature Exceeded
Alarm
Alarm 1 nn102 Ch0 LightLim Alm Channel 0 Light Limit Alarm
Alarm 1 nn103 Ch0 Battery Alm Channel 0 Battery Alarm

Alarm 1 nn104 Ch0 RefPoint Alm Channel 0 Reference Point Alarm
Alarm 1 nn108 Ch0 General Alm Channel 0 General Alarm
Alarm 1 nn115 Ch0 Optics Alarm Channel 0 Optics Alarm
Alarm 1 nn116 Ch0 OutOfRailAlm Channel 0 Out Of Rail Alarm
Configurable nn200 Ch1 LightSrc Err Channel 1 Light Source Error
Configurable nn201 Ch1 SigAmp Err Channel 1 Signal Amplitude Error
Configurable nn202 Ch1 PsnVal Err Channel 1 Position Value Error
Configurable nn203 Ch1 OverVolt Err Channel 1 Overvoltage Error
Configurable nn204 Ch1 UndVolt Err Channel 1 Undervoltage Error
Configurable nn205 Ch1 OverCur Err Channel 1 Overcurrent Error

Configurable nn206 Ch1 Battery Err Channel 1 Battery Error
Configurable nn209 Ch1 AnalSig Err Channel 1 Analog Signal Error
Configurable nn210 Ch1 IntOfst Err Channel 1 Interface Offset Error
Configurable nn211 Ch1 DataTabl Err Channel 1 Data Table Error
Configurable nn212 Ch1 AnalLim Err Channel 1 Analog Limit Error
Configurable nn213 Ch1 Int I2C Err Channel 1 Internal I2C Error
Configurable nn214 Ch1 IntChksm Err Channel 1 Internal Checksum Error

Configurable nn215 Ch1 PrgmResetErr Channel 1 Program Reset Error
Configurable nn216 Ch1 CntOvrflwErr Channel 1 Counter Overflow Error
Configurable nn217 Ch1 Parity Err Channel 1 Parity Error
Configurable nn218 Ch1 Chksum Err Channel 1 Checksum Error
Configurable nn219 Ch1 InvCmd Err Channel 1 Invalid Command Error
Configurable nn220 Ch1 SendSize Err Channel 1 Send Size Error
Configurable nn221 Ch1 CmdArgmt Err Channel 1 Command Argument Error

Configurable nn222 Ch1 InvWrtAdrErr Channel 1 Invalid Write Address Error
Configurable nn223 Ch1 AccCode Err Channel 1 Access Code Error
Configurable nn224 Ch1 FieldSizeErr Channel 1 Field Size Error
Configurable nn225 Ch1 Address Err Channel 1 Address Error
Configurable nn226 Ch1 FieldAcc Err Channel 1 Field Access Error
Configurable nn228 Ch1 SiTurnPsnErr Channel 1 Single Turn Position Error
Configurable nn229 Ch1 MulTrnPsnErr Channel 1 Multiple Turn Position

Error
Configurable nn236 Ch1 AnalVal Err Channel 1 Analog Value Error
Configurable nn237 Ch1 SendCurr Err Channel 1 Send Current Error
Configurable nn238 Ch1 EncTemp Err Channel 1 Encoder Temperature

Error
Configurable nn239 Ch1 Speed Err Channel 1 Speed Error
Configurable nn240 Ch1 General Err Channel 1 General Error
Configurable nn246 Ch1 LED Curr Err Channel 1 LED Current Error
Configurable nn247 Ch1 ExMulTurnErr Channel 1 External Multi-Turn Error

Configurable nn248 Ch1 PsnCode Err Channel 1 Position Code Error
Configurable nn249 Ch1 Config Err Channel 1 Configuration Error
Configurable nn250 Ch1 PsnVal Err Channel 1 Position Not Valid Error
Configurable nn251 Ch1 SerialComErr Channel 1 Serial Communication

Error
Configurable nn252 Ch1 Ext Failure Channel 1 External Failure
Configurable nn253 Ch1 Temp Exc Err Channel 1 Temperature Exc Error
Configurable nn256 Ch1 OutOfRailErr Channel 1 Out Of Rail Error

Configurable nn262 Ch1 RAM Error Channel 1 RAM Error
Configurable nn263 Ch1 EPROM Error Channel 1 EPROM Error
Configurable nn264 Ch1 ROM Error Channel 1 ROM Error
Configurable nn266 Ch1 No Position Channel 1 No Position
Configurable nn281 Ch1 Msg Cheksum Channel 1 Message Checksum

Configurable nn282 Ch1 Timeout Channel 1 Timeout
Configurable nn283 Ch1 Comm Channel 1 Communications
Configurable nn284 Ch1 Diagnostic Channel 1 Diagnostic
Configurable nn285 Ch1 SpplyVltgRng Channel 1 Supply Voltage Range
Configurable nn286 Ch1 SC Amplitude Channel 1 SC Amplitude
Configurable nn287 Ch1 Open Wire Channel 1 Open Wire
Configurable nn288 Ch1 Quad Loss Channel 1 Quadrature Loss

Configurable nn289 Ch1 Phase Loss Channel 1 Phase Loss
Configurable nn290 Ch1 Unsupp Enc Channel 1 Unsupported Encoder
Alarm 1 nn300 Ch1 FreqExc Alm Channel 1 Frequency Exceeded

Alarm
Alarm 1 nn301 Ch1 TempExc Alm Channel 1 Temperature Exceeded
Alarm
Alarm 1 nn302 Ch1 LightLim Alm Channel 1 Light Limit Alarm
Alarm 1 nn303 Ch1 Battery Alm Channel 1 Battery Alarm
Alarm 1 nn304 Ch1 RefPoint Alm Channel 1 Reference Point Alarm
Alarm 1 nn308 Ch1 General Alm Channel 1 General Alarm
Alarm 1 nn315 Ch1 Optics Alarm Channel 1 Optics Alarm
Alarm 1 nn316 Ch1 OutOfRailAlm Channel 1 Out Of Rail Alarm
Non-Resettable nn412 Hardware Err Hardware Error

Fault
Non-Resettable nn413 Firmware Err Firmware Error

Fault
Alarm 1 nn416 EncOut Cflct Encoder Output Conflict
Alarm 1 nn417 Safety Cflct Safety Conflict
Alarm 1 nn420 FB0FB1 Cflct FB0FB1 Conflict
Alarm 1 nn421 Initializing Initializing

Configurable nn999 System Comm Loss System Communications Loss
Alarm 1 nn001 High Temp High Temperature
Configurable nn002 Over Temp Over Temperature
Configurable nn003 Comm Watchdog Communications Watchdog
Configurable nn004 Fiber Offline Fiber Offline
Configurable nn006 Ext Pwr Loss External Power Loss
Alarm 2 nn007 Sys Misconfig System Misconfiguration

Alarm 2 nn008 Drive Misconfig Drive Misconfiguration
Configurable nn999 System Comm Loss System Communications Loss

Fault
Analog input 0 has a lost signal.
Predictive maintenance for relay 0.
Predictive maintenance for relay 1.
An over-temperature condition has been detected in the motor, or the

sensor path has been broken.
A short circuit condition has been detected in the sensor path.
Possible hardware damage. The motor to the thermal sensor is shorted.

Excessive EMC noise due to improper grounding/shielding.
An over-temperature condition has been detected in the motor, or the

sensor path has been broken.
Possible hardware damage. The motor to the thermal sensor is shorted.

Excessive EMC noise due to improper grounding/shielding.
I/O option module has stopped communicating with the main control board.
SI comm is down.
The safety option module has lost backplane communications with the main
control board.
The hardware enable jumper is not installed in a safety system.

The safety jumper is not installed in a non-safety system.
The safety jumper is installed in a non-safety system (system with no safety

option module).
Safety health error.
Safety Vcc is on when it should be off.
Safety Vcc is off when it should be on.
control board.
CIP Safety Feedback

The Integrated Safety - Safe Torque Off (20-750-S3) option module detected
a safe torque off condition.
The S3 option module detected an internal fault.
The S3 option module detected a gate drive fault.
The S3 option module detected a stop fault.
control board.
The encoder module has detected an input signal (A, B, or Z) in the same
state as its complement (A Not, B Not, or Z Not). For open wire detection to
work, the encoder signals must be differential (not single ended). The Z
channel is only checked when enabled.
More than 30 phase loss (open wire) events have occurred over an 8
millisecond time period. The same restrictions as for Open Wire detection
apply.
Quadrature loss events occur when simultaneous edge transitions occur on
both the A and B encoder channels. This fault occurs when more than 10
quad loss events over a 10 millisecond time period are detected. Only valid
when both A and B channels are used (not bit 1 ‘A Chan Only’) in parameter
nn:1 [Encoder Cfg].
A Feedback Loss has been detected for the source of 10:1040 [Pri Vel
Feedback]. This could be due to a problem detected by the feedback option
module selected by 10:1000 [Pri Vel Fb Sel] or due to a loss in
communication between the feedback option module and main control
board. The source of primary velocity feedback must be configured not to
fault if the feedback loss switchover feature is used.
A Feedback Loss has been detected for the source of 10:1041 [Alt Vel
module selected by 10:1006 [Alt Vel Fb Sel] or due to a loss in
board.
A Feedback Loss has been detected for the source of 10:1832 [Enc VRef Sel].
This could be due to a problem detected by the feedback option module
selected by 10:1832 [Enc VRef Sel] or due to a loss in communication
between the feedback option module and main control board.
A Feedback Loss has been detected for the source of 10:1769 [Pri Position
Fb]. This could be due to a problem detected by the feedback option module
selected by 10:1013 [PReg Fb Sel] or due to a loss in communication
A Feedback Loss has been detected for the source of 10:1770 [Alt Position
selected by 10:1012 [Alt Preg Fb Sel] or due to a loss in communication
The encoder option module has lost backplane communications with the
main control board.
The dual encoder module has detected an encoder 0 input signal (A, B, or Z)
in the same state as its complement (A Not, B Not, or Z Not). For open wire
detection to work, the encoder signals must be differential (not single
ended). The Z channel is only checked when enabled. See parameter nn:1
[Enc 0 Cfg].
More than 30 encoder 0 phase loss (open wire) events have occurred over
an 8 millisecond time period. The same restrictions as for Enc0 Open Wire
detection apply.
Encoder 0 Quadrature loss events occur when simultaneous edge transitions

occur on both the A and B channels of encoder 0. This fault occurs when
more than 10 quad loss events over a 10 millisecond time period are
detected. Only valid when both A and B channels are used (not bit 1 ‘A Chan
Only’) in parameter nn:1 [Enc 0 Cfg].
The dual encoder module has detected an encoder 1 input signal (A, B, or Z)
in the same state as its complement (A Not, B Not, or Z Not). For open wire
detection to work, the encoder signals must be differential (not single
ended). The Z channel is only checked when enabled. See parameter nn:11
[Enc 1 Cfg].
More than 30 encoder 1 phase loss (open wire) events have occurred over
an 8 millisecond time period. The same restrictions as for Enc1 Open Wire
detection apply.
Encoder 1 Quadrature loss events occur when simultaneous edge transitions

occur on both the A and B channels of encoder 1. This fault occurs when
more than 10 quad loss events over a 10 millisecond time period are
detected. Only valid when both A and B channels are used (not bit 1 ‘A Chan
Only’) in parameter nn:11 [Enc 1 Cfg].
board.
The encoder option module has lost backplane communications with the
main control board.
Error reported by Heidenhain Encoder on Channel 0 with EnDat Interface -

Light source failure.

Signal amplitude error.
Position value error.

Overvoltage error.

Undervoltage error.

Overcurrent error.

Battery empty.
Error reported by Stegmann Encoder on Channel 0 with Hiperface Interface -

Analog signals outside specification.

Faulty internal angular offset.
Data field partitioning table damaged.

Analog limit values not available.

Internal I2C bus not operational.

Internal checksum error.

Encoder reset occurred as a result of program monitoring.

Counter overflow.

Parity error.
Checksum of the data transmitted is incorrect.

Unknown command code.

Number of data transmitted is incorrect.

Command argument transmitted is not allowed.

The selected data field must not be written to (invalid write address).

Incorrect access code.

Size of data field stated cannot be changed.
Word address stated is outside data field.

Access to non-existent data field.

Single turn position unreliable.

Multiple turn position unreliable.

Analog value error (process data).

Transmitter current critical (dirt, broken transmitter).

Encoder temperature critical.
Speed too high, no position formation possible.
Error reported by a Encoder on Channel 0 with BiSS Interface - An error bit of

the BiSS Single Cycle Data is set.
Error reported by a Encoder on Channel 0 with BiSS Interface - LED current

out of control range.
Error reported by a Encoder on Channel 0 with BiSS Interface - External

multiturn error.
Error reported by a Encoder on Channel 0 with BiSS Interface - Position code

error (single step error).
Error reported by a Encoder on Channel 0 with BiSS Interface - failure

configuring interface.
Error reported by a Encoder on Channel 0 with BiSS Interface - Position data

not valid.
Error reported by a Encoder on Channel 0 with BiSS Interface - Serial
interface failure.

failure over NERR.
Error reported by a Encoder on Channel 0 with BiSS Interface - Temperature

out of defined range.
Parameter values for this option module have been reset to their default
settings.
Error reported by a linear Stahl encoder on Channel 0 - Rail is no longer
present between the read head.
Error reported by a linear Stahl encoder on Channel 0 - Indicates that the

read head must be cleaned or installed correctly.

Error reported by a linear Stahl encoder on Channel 0 - Indicates a RAM

error. Reading head needs to be repaired.
Error reported by a linear Stahl encoder on Channel 0 - Indicates a EPROM
Error reported by a linear Stahl encoder on Channel 0 - Indicates a ROM

Error reported by a linear Stahl encoder on Channel 0 - Indicates that no

position value was available - only possible following powerup or reset.
Indicates the option module has detected a serial communications checksum

error while attempting to communicate with the encoder on channel 0.
Indicates the option module has detected a serial communications timeout

Indicates the option module has detected a serial communications error

(other than checksum or timeout) while attempting to communicate with
the encoder on channel 0.
Indicates the option module has detected a powerup diagnostic test failure
for encoder channel 0.
Indicates that the voltage source to the encoder 0 is out of range.
Indicates that the encoder 0 signal amplitude is out of tolerance.
Indicates that an open wire condition has been detected for encoder 0.
Indicates that a signal quadrature error has been detected for encoder 0.
Add ferrite cores.
Indicates that an A or B signal of an A quad B incremental encoder on

Channel 0 is disconnected.
Indicates that the connected encoder on Channel 0 is not supported.
Alarm reported by Heidenhain Encoder on Channel 0 with EnDat Interface -

Frequency exceeded warning.
Temperature exceeded warning.
Limit of light control reserve reached.
Battery warning.
Reference point not reached.
Alarm reported by a Encoder on Channel 0 with BiSS Interface - A warning bit
of the BiSS Single Cycle Data is set.
Alarm reported by a linear Stahl encoder on Channel 0 - Displays an alarm
when the Stahl optical system requires cleaning.
Alarm reported by a linear Stahl encoder on Channel 0 - Indicates that the
read encoder count is at the maximum value (524287).
Light source failure.

Signal amplitude error.

Position value error.

Overvoltage error.

Undervoltage error.

Overcurrent error.
Battery empty.

Analog signals outside specification.

Faulty internal angular offset.

Data field partitioning table damaged.

Analog limit values not available.

Internal I2C bus not operational.

Internal checksum error.
Encoder reset occurred as a result of program monitoring.

Counter overflow.

Parity error.

Checksum of the data transmitted is incorrect.

Unknown command code.

Number of data transmitted is incorrect.

Command argument transmitted is not allowed.
The selected data field must not be written to (invalid write address).

Incorrect access code.

Size of data field stated cannot be changed.

Word address stated is outside data field.

Access to non-existent data field.

Single turn position unreliable.

Multiple turn position unreliable.
Analog value error (process data).

Transmitter current critical (dirt, broken transmitter).

Encoder temperature critical.

Speed too high, no position formation possible.
Error reported by a Encoder on Channel 1 with BiSS Interface - An error bit of

the BiSS Single Cycle Data is set.
Error reported by a Encoder on Channel 1 with BiSS Interface - LED current

out of control range.

multiturn error.
Error reported by a Encoder on Channel 1 with BiSS Interface - Position code
error (single step error).
Error reported by a Encoder on Channel 1 with BiSS Interface - failure

configuring interface.
Error reported by a Encoder on Channel 1 with BiSS Interface - Position data

not valid.
Error reported by a Encoder on Channel 1 with BiSS Interface - Serial

interface failure.

failure over NERR.
Error reported by a Encoder on Channel 1 with BiSS Interface - Temperature

out of defined range.
Error reported by a linear Stahl encoder on Channel 1 - Rail is no longer

present between the read head.

Error reported by a linear Stahl encoder on Channel 1 - Indicates a RAM

Error reported by a linear Stahl encoder on Channel 1 - Indicates a EPROM

Error reported by a linear Stahl encoder on Channel 1 - Indicates a ROM

Error reported by a linear Stahl encoder on Channel 1 - Indicates that no

position value was available - only possible following powerup or reset.
Indicates the option module has detected a serial communications checksum

Indicates the option module has detected a serial communications timeout
Indicates the option module has detected a serial communications error

(other than checksum or timeout) while attempting to communicate with
the encoder on channel 1.
Indicates the option module has detected a powerup diagnostic test failure
for encoder channel 1.
Indicates that the voltage source to the encoder 1 is out of range.
Indicates that the encoder 1 signal amplitude is out of tolerance.
Indicates that an open wire condition has been detected for encoder 1.
Indicates that a signal quadrature error has been detected for encoder 1.
Indicates that an A or B signal of an A quad B incremental encoder on
Channel 1 is disconnected.
Indicates that the connected encoder on Channel 1 is not supported.

Frequency exceeded warning.
Temperature exceeded warning.
Limit of light control reserve reached.
Battery warning.
Reference point not reached.
Alarm reported by a Encoder on Channel 1 with BiSS Interface - A warning bit
of the BiSS Single Cycle Data is set.
Alarm reported by a linear Stahl encoder on Channel 1 - Displays an alarm
when the Stahl optical system requires cleaning.
Alarm reported by a linear Stahl encoder on Channel 1 - Indicates that the
read encoder count is at the maximum value (524287).
Indicates that there is a Hardware Error on the Feedback Option module.
Indicates that there is a Firmware Error on the Feedback Option module. A

Firmware Error occurs if the Hardware and the downloaded Firmware are
not compatible.
This could also indicate that communication between the Feedback Option
module and the Main Control Board was interrupted during power up.
Indicates that there is one of the following problems with the Encoder
Output:
• The selection in the nn:80 [Enc Out Sel] is not possible since the required
pins on the terminal blocks are already used for Feedback 0 or 1 according to
nn:6 [FB0 Device Sel] and nn:36 [FB1 Device Sel].
• nn:80 [Enc Out Sel] is set to 2 ‘Sine Cosine’ and there is no signal connected
to the pins 1…4 of TB 1.
• nn:80 [Enc Out Sel] is set to 2 ‘Sine Cosine,’ the value of 15/45 [FBX
IncAndSC PPR] is not a power of two, and 84 [EncOut Z PPR] is not set to 0 ‘1
ZPulse.’ This is not allowed.
• nn:80 [Enc Out Sel] is set to 3 ‘Channel X’ or 4 ‘Channel Y’ and there is no
encoder connected to that channel.
• nn:80 [Enc Out Sel] is set to 3 ‘Channel X’ or 4 ‘Channel Y’ and there is a
linear encoder connected to this channel.
The option module has a conflict with the configuration of the safety
switches.
The option module has a conflict with the configuration of the two channels.
The option module asserts this condition when it is setting up initial

communication with the encoders.
board.
The option module has lost communication with the ICB on the backplane.
Possible causes include poor connection on backplane connector or
damaged option module.
The temperature of a TLink card has exceeded the alarm temperature (75
°C). Possible causes include high ambient temperature and obstructed
airflow.
The temperature of a TLink option module has exceeded the fault

temperature (80 °C). Possible causes include high ambient temperature and
obstructed airflow.
Possible only in follower drive, not possible in leader and bypass

configuration. Message timeout on fiber-optic interface was detected.
Possible causes are broken fiber-optic link or leader drive failure.
Not detected in bypass configuration. Rn fiber-optic cable is not connected

to TLink option module or preceding node is not sending any data. Possible
causes are disconnected or damaged fiber-optic cable or failure of one of
preceding drives.
External power supply is not provided. Normal operation is not affected but
the link to succeeding drives breaks if drives are powered down.
Possible only in follower drive. TLink card receives incompatible packets.

Possible when leader drive is configured to different mode than follower
drive.
The selected and active motor control mode is not compatible with the TLink
option module. The TLink option module is only compatible with flux vector
control modes in the primary motor control port (Port 10). It is not
compatible with scalar modes such as volts per Hertz or sensorless vector. It
is not compatible with any motor control modes configured for the
secondary motor control port (Port 11). Not detected in bypass
configuration.
The option module has lost communication with the ICB on the backplane.
Possible causes include poor connection on backplane connector or
damaged option module.
Option
Action
— I/O
— I/O
— I/O
— I/O
— I/O
— I/O
If unable to clear fault, be sure the thermal sensor that is connected is a PTC type I/O
and not a thermostatic type.
— I/O
— I/O
— I/O
— I/O
— Safe Torque Off (20-750-

S)
— Safe Speed Monitor (20-

750-S1)
750-S1)

750-S1)

750-S1)

750-S1)

750-S1)

750-S1)
— Integrated Safety
Functions (20-750-S4)
— Integrated Safety - Safe
Torque Off (20-750-S3)




See parameter nn:1 [Encoder Cfg] Single Incremental

Encoder
— Single Incremental
Encoder
Encoder
Encoder
Encoder
Encoder
Encoder
Encoder
Encoder
— Dual Incremental
Encoder
Encoder
Encoder
Encoder
Encoder
Encoder
Encoder
Encoder
Encoder
Encoder
Encoder
Encoder
— Universal Feedback
Cycle power to clear this fault. Universal Feedback

Check the ambient temperature. Check the condition of cabinet air filters. TLink
Check the ambient temperature. Check the condition of cabinet air filters. TLink
Check all fiber-optic cables starting from this drive and going up to leader drive. TLink
Verify that the leader drive is operating and is configured correctly. Verify that all
preceding follower drives are operating and are configured correctly. If any of the
preceding followers is powered down check if external power supply is provided to
its TLink option module.
Can be ignored in leader drive when ring connection is not needed. Otherwise TLink
check all fiber-optic cables starting from this drive and going up to the leader drive.
Verify that the leader drive is operating and is configured correctly. Verify that all
preceding follower drives are operating and are configured correctly. If any of the
preceding follower drives is powered down check if external power supply is
provided to its TLink option module.
Can be ignored when external supply is not supposed to be provided to a TLink TLink
option module. Otherwise, check if external power supply is connected. Check if
power supply is operating.
Check if parameter nn:001 [TLink Mode] is configured the same in both the leader TLink
and follower drives.
Adhere to the following configuration constraints when enabling the TLink card. TLink
- Select the primary motor control port in parameter 0:75 [Motor Ctrl Sel].
- Confirm that the primary motor control port is selected in parameter 0:75 [Mtr
Ctrl Sel Act].
- Confirm that parameter 0:67 [Sec MtrCtrl Mode] and parameter 0:68 [Sec MtrCtrl
Act] are both set to none.
- Select a flux vector control mode in the primary motor control port with
parameter 0:65 [Pri MtrCtrl Mode].
- Confirm that the active motor control mode is flux vector in parameter 0:66 [Pri
MtrCtrl Act].
Power down drive before removing or inserting a TLink option module. Verify that TLink
the option module is inserted firmly into backplane. Replace the option module.
Configurable nn:53 [Anlg In0 LssActn]

OVRD] bit 11 ‘Port 4 Flts’ … bit 15 ‘Port 8 Flts’
Configurable nn:63 [Anlg In1 LssActn]

Configurable nn:106 [RO0 LifeEvntActn]

Configurable nn:116 [RO1 LifeEvntActn]

Coast —
Configurable nn:40 [PTC Cfg]

Configurable nn:40 [PTC Cfg]
Coast —
Coast —
Coast —
Coast —
Coast —
fault.
Coast —
fault.
Coast —
fault.
Coast —
fault.
Coast —
fault.
Coast —
fault.
Coast —
fault.
Coast —
fault.
Coast —
fault.
Coast —
fault.
Coast —
fault.
Coast —
fault.
Coast —
fault.
Coast —
fault.
Configurable nn:3 [Fdbk Loss Cfg]








Configurable nn:3 [Enc 0 FB Lss Cfg]





Configurable Either
Additional Fault Action nn:3 [Enc 0 FB Lss Cfg]
Fault opens main circuit breaker: No nn:13 [Enc 1 FB Lss Cfg]
Configurable Either
Configurable Either
Configurable Either
Configurable Either

Configurable nn:9 [FB0 Loss Cfg]

















































— —
— —
— —
— —
— —
— —
— —
— —









































— nn:39 [FB1 Loss Cfg]








— —
— —
— —
— —
— —
— —
— —
— —
Coast —
fault.
Coast —
fault.
— —
— —
— —
— —
Configurable Either
Additional Fault Action nn:9 [FB0 Loss Cfg]
Fault opens main circuit breaker: No nn:39 [FB1 Loss Cfg]
Configurable Either
Configurable Either
Configurable Either
Configurable Either
Configurable Either
— —
Configurable nn:15 [OverTempCfg]

Configurable nn:11 [CommWatchdogCfg]

Configurable nn:13 [FibOfflineCfg]

Configurable nn:14 [ExtPwrLossCfg]

— —
— —
Configurable nn:12 [SysCommLossCfg]

Configurable Action
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
Hold Input
Set Input Lo
Set Input Hi
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
Hold Input
Set Input Lo
Set Input Hi
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
—
—
—
—
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
—
—
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
—
—
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
Ignore
Alarm
Flt Minor
—
—
Ignore
Alarm
Flt Minor
FltCoastStop
Flt RampStop
Flt CL Stop
Fault Code 73 DigIn Cfg B - Converter Fault Code 73 DigIn Cfg B - Inverter
Digital Input combinations marked ‘•’ cause an alarm. Digital Input combinations marked ‘•’ cause an alarm.
DI EmergencyOVRD
DI EmergencyOVRD
DI M Stop Mode B
DI M Fwd Reverse
DI M Manual Ctrl
DI AC LineSource
DI M Speed Sel 2
DI M Speed Sel 1
DI M Speed Sel 0
DI M Decel Time
DI M Accel Time
DI Energy Pause
DI Mtr Ctrl Sel

DI Clear Fault
DI Aux Fault
DI M Jog 2
DI M Jog 1
DI L Start
DI L Stop
DI L Run
DI L Stop DI M Stop
DI Aux Fault DI M Coast Stop
DI Clear Fault DI M CurLmt Stop
DI L Start • DI Aux Fault
DI L Run • DI Regen OK
DI Energy Pause DI Clear Fault
DI EmergencyOVRD DI M HOA Start
DI AC LineSource DI M Start
DI M Run
DI M Jog 1
DI M Jog 2
DI M Fwd Reverse
DI M Accel Time
DI M Decel Time
DI M Manual Ctrl
DI M Speed Sel 0
DI M Speed Sel 1
DI M Speed Sel 2
DI M Stop Mode B
DI EmergencyOVRD
DI Mtr Ctrl Sel
Fault Code 74 DigIn Cfg C - Converter Fault Code 74 DigIn Cfg C - Inverter
Digital Input combinations marked ‘•’ cause an alarm. Digital Input combinations marked ‘•’ cause an alarm.
DI EmergencyOVRD
DI EmergencyOVRD
DI M Stop Mode B
DI M Fwd Reverse
DI M Manual Ctrl
DI AC LineSource
DI M Speed Sel 2
DI M Speed Sel 1
DI M Speed Sel 0
DI M Decel Time
DI M Accel Time
DI Energy Pause
DI Mtr Ctrl Sel

DI Clear Fault
DI Aux Fault
DI M Jog 2
DI M Jog 1
DI L Start
DI L Stop
DI L Run
DI L Stop • • • • • • DI M Stop • • • • • • • • •
DI Aux Fault • • • • • • DI M Coast Stop • • • • • • • • •
DI Clear Fault • • • • • DI M CurLmt Stop • • • • • • • • •
DI L Start • • • • • DI Aux Fault • • • • • • • • • •
DI L Run • • • • • • DI Regen OK (CR1 R2) • • • • • • • • • •
DI Energy Pause • • • • • • DI Clear Fault • • • • • • • •
DI EmergencyOVRD • • • • • • DI M HOA Start • • • • • • • • • •
DI AC LineSource • • DI M Start • • • • • • • • • •
DI M Run • • • • • • • • • • •
DI M Jog 1 • • • • • • • • •
DI M Jog 2 • • • • • • • • •
DI M Fwd Reverse • • • • • • • • •
DI M Accel Time • • • • • • • •
DI M Decel Time • • • • • • • •
DI M Manual Ctrl • • • • • • •
DI M Speed Sel 0 • • • • • • • • •
DI M Speed Sel 1 • • • • • • • • •
DI M Speed Sel 2 • • • • • • • • •
DI M Stop Mode B
DI EmergencyOVRD • • • • • • • • •
DI Mtr Ctrl Sel • •
•
•
DI M Run
•
•
DI M Start
•
•
DI M HOA Start
DI Clear Fault
DI Regen OK
DI Aux Fault
DI M CurLmt Stop
DI M Coast Stop
DI M Stop
DI Regen OK (CR1 R2)
DI M CurLmt Stop
DI M Coast Stop
DI M HOA Start
DI Clear Fault
DI Aux Fault
DI M Start
DI M Stop
DI M Run
• • • • • • • •
• • • • • • • •
• • • • • • • •
• • • • • • •
• • • • • • •
• • • • • •
• • • • •
• • • • •
• • • • • •
• • • • •
• • • • •
• • • • • • • • •
• • • • • • • • •
• • • • • • • • •
• • • • • • •
• • • • • • • • •
• • • • • • • • •
• • • • • • • • •
• • • • • • • • •
• • • • • •
Control Pod Fiber Diagram
See the product installation instructions, publication 750-IN100, for cable lengths and catalog numbers.
Main Control Circuit Board
Fiber-Optic Interface Circuit Board
Transceiver Circuit Board
AC Precharge (ACPC) Circuit Board Location
DC Precharge (DCPC) Circuit Board Location
Power Layer Interface Circuit Board—Frame 7
Power Layer Interface Circuit Board—Frame 8 and larger
Power Interface Circuit Board—Frame 7
Power Interface Circuit Board—Frame 8 and larger
Current Sense Circuit Board—Frame 7
Current Sense Circuit Board—Frame 8 and larger
Torque Accuracy Module
Syslog Messages
These syslog messages apply to PowerFlex Drives with TotalFORCE Control.
For more information, see these resources:
PowerFlex Drives with TotalFORCE Control Programming Manual, 750-PM101
CIP Security with Rockwell Automation Products Application Technique, SECURE-AT001
Type ID Message Guidance
CIP Security enabled target fails the establishment of a secure I/O session.
Where:
%src% = The source device that attempted to establish the secure session.
CIP Security™ cipsec_dtls_srv_session_failed %src% failed to start CIP Security I/O session. Error=%err% %err% = The error code that indicates the underlying cause of the failure.
CIP Security enabled target successfully establishes a secure I/O session.

Where:
CIP Security™ cipsec_dtls_srv_session_started %src% started CIP Security I/O session %src% = The source device that established the secure session.
CIP Security enabled endpoint is deployed a new Certificate Revocation List (CRL).
Where:
%username% = The user name associated with the identity that deployed the new CRL.
CIP Security™ cipsec_new_crl_configured A new CRL for CIP Security was received from %username% at %src% %src% = The source device that deployed the CRL.
CIP Security enabled endpoint is deployed a new active certificate in the EtherNet/IP CIP security object.
Where:
%username% = The user name associated with the identity that deployed the new identity.
CIP Security™ cipsec_new_identity_configured A new CIP Security identity was received from %username% at %src% %src% = The source device that deployed the new identity.
CIP Security enabled endpoint fails to accept a new active certificate in the EtherNet/IP CIP security object.
Where:
%username% = The user name associated with the identity that attempted to deploy the new identity.
CIP Security™ cipsec_new_identity_failed A new CIP Security identity failed to be accepted from %username% at %src% %src% = The source device that attempted to deploy the new identity.
CIP Security enabled endpoint successfully deployed new policies that can affect the CIP Security configuration.
Where:
%username% = The user name associated with the identity that deployed the new policy.
%src% = The source device that deployed the new policy.
CIP Security™ cipsec_new_policy A new policy for %name% was configured by %username% at %src% %name% = The identifier for the policy that was changed. See the preceding table for a list of known policies.
CIP Security enabled target fails the establishment of a secure messaging session.
Where:
%src% = The source device that attempted to establish the secure session.
CIP Security™ cipsec_tls_srv_session_failed %src% failed to start CIP Security messaging session. Error=%err% %err% = The error code that indicates the underlying cause of the failure.
CIP Security enabled target successfully establishes a secure messaging session.

Where:
CIP Security™ cipsec_tls_srv_session_started %src% started CIP Security messaging session %src% = The source device that established the secure session.
CIP Security enabled endpoint is deployed a new trusted certificate in the EtherNet/IP CIP security object.
Where:
%username% = The user name associated with the identity that deployed the new policy.
%src% = The source device that deployed the new policy.
CIP Security™ cipsec_trust_modified CIP Security trust was modified by %username% at %src% %name% = The identifier for the policy that was changed. See the preceding table for a list of known policies.
Critical configuration change successfully takes place.

Any configuration change that is normally guarded by an implicit or explicit protection mode and not covered by a more specific event
is considered a critical configuration change.
Where:
%username% = The username that made the configuration change.
Configuration config_critical_change Configuration in subsystem %subsystem% was modified by user %username% from source %src% %src% = The source that the change was requested from.
Critical configuration change is rejected.

Any configuration change that is normally guarded by an implicit or explicit protection mode and not covered by a more specific event
is considered a critical configuration change.
Where:
%username% = The username that requested the configuration change.
Configuration config_critical_change_failed Failed configuration change subsystem %subsystem% by user %username% from source %src%. Error=%err% %src% = The source that the change was requested from.
Network related configuration change successfully takes place.
Where:
%username% = The username that made the configuration change.
Configuration config_network_change Network configuration was modified by user %username% from source %src% %src% = The source that the change was requested from.
Network configuration change is rejected.

Where:
%username% = The username that requested the configuration change.
Configuration config_network_change_failed Failed to modify network configuration by user %username% from source %src%. Error=%err% %src% = The source that the change was requested from.
Product firmware update fails.

Where:
%username% = The username of the identity that attempted the firmware update.
%src% = The source that originated the firmware update.
System sys_firmware_update_failed Failed to update firmware by %username% at %src%. Error=%err% %err% = The error code that indicates the underlying cause of the failure.
Product firmware update begins.

Where:
%username% = The username of the identity that performed the firmware update.
System sys_firmware_update_started Firmware update started by %username% at %src% %src% = The source that originated the firmware update.
Product firmware update completes successfully.

Where:
%username% = The username of the identity that performed the firmware update.
System sys_firmware_update_completed Firmware updated by %username% at %src% %src% = The source that originated the firmware update.
Product is requested to power down.
Where:
%username% = The username of the identity that initiated the power down.
System sys_powerdown Powered down by %username%
System sys_powerup Powered up Product is powered up.
Product is successfully requested to be restarted.

Where:
%type% = The type of the reset that was requested. This may be "Power cycle", "Factory", "Factory without communications",
"Secure", or a product specific value.
%username% = The username of the identity that initiated the reset.
System sys_reset %type% reset by %username% from %src% %src% = The source the reset request was initiated from.
Product is requested to be restarted by the request fails or is rejected.

Where:
%type% = The type of the reset that was requested. This may be "Power cycle", "Factory", "Factory without communications",
"Secure", or a product specific value.
%username% = The username of the identity that initiated the reset.
%src% = The source the reset request was initiated from.
System sys_reset_failed %type% reset by %username% from %src% failed. Error=%err% %err% = The error code the identifies the underlying cause of the error.
Fired when a product loses power.

This event can be fired immediately upon detection of power loss, if the product still has energy to issue the event. Alternatively, if
the product can detect a previous power loss during its power up sequence, it may fire this event prior to firing its sys_powerup
System sys_powerloss Power lost event.
System clock is started.

Where:
System sys_clock_start Clock started by %username% %username% = The username of the identity that started the system clock.
System clock is stopped.

Where:
System sys_clock_stop Clock stopped by %username% %username% = The username of the identity that stopped the system clock.
The protocol that synchronizes the product clock with a time source authority has failed.
Where:
System sys_clock_sync_lost Clock synchronization with %source% has been lost %src% = The time source authority that the product clock would synchronize with.
The protocol that synchronizes the product clock with a time source authority has been established.
Where:
System sys_clock_synced Clock is now synchronized with %source% %src% = The time source authority that the product clock is synchronized with.
The product clock has been changed by a mechanism other than the typical time synchronization protocol.
Where:
System sys_clock_time_change Clock time changed by %username% %username% = The user name of the identity that changed the time.
Fired when a major fault occurs.
Where:
System sys_major_fault A major fault occurred. Error=%err% %err% = Major Fault Error.
Fired when major faults are cleared.

Where:
%username% = User which cleared the faults.
System sys_clear_major_fault Major faults were cleared by user %username% from %src% %src% = Source of the clear faults command.
System sys_clear_major_fault_local Major faults were cleared through the local means Fired when major faults are cleared through local means (e.g. a key switch).
Log log_config_change Log service configuration changed by %username% from %src% A configuration change was made to the products log system.
Where:
%username% = The username of the identity that made the change.
%src% = The source that originated the configuration change.
Log log_config_change_failed Failed to change log service configuration by %username% from %src%. Error=%err% A configuration change to the product's log system was requested but could not bechanged.
Where:
%username% = The username of the identity that made the change.
%src% = The source that originated the configuration change.
%err% = The error code that indicates the underlying cause of the failure.
Log log_messages_overrun %count% log messages could not be sent and have been lost. Error=%err% Event messages could not be delivered to a destination.
The event can also occur when a logging subsystem must overwrite unread messages due to a capacity limit.
This may occur due to an event flood that exceeds the buffering resources of the product or because a prolonged service outage that
prevents events from being delivered.
Where:
%count% = The number of events that haveen been dropped.
%err% = The error code that identifies the underlying root cause that the messages were dropped.
A TCP session cannot be created with the Syslog collector.

Where:
%dst% = The destination Syslog collector.
Log log_tcp_cli_session_failed Failed to start connection with log service at %dst%. Error=%err% %err% = The error code that indicates the underlying cause of the failure.
A TCP session is successfully established with the Syslog collector.

Where:
Log log_tcp_cli_session_started Started connection with log service at %dst% %dst% = The destination Syslog collector.
The product attempts to originate an event, but no definition of the event exists.
Where:
%id% = The numeric identifier of the event that the product attempts to generate.
Log log_unknown_event An undefined event was generated. ID=%id% Context=%ctx% %ctx% = A formatted string of the context values associated with the event.

Powerflex Drives With Totalforce Control Conditions Reference Data

Uploaded by

Copyright:

Available Formats

Powerflex Drives With Totalforce Control Conditions Reference Data

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Powerflex Drives With Totalforce Control Conditions Reference Data

Uploaded by

Copyright:

Available Formats

750-RD102C-EN-P

PowerFlex Drives with TotalFORCE Control Conditions Reference Data

Port 10-11 Tab

Resettable Fault 2 Sys Default Fail System Reset to Defaults Failure

Alarm 1 3 Emerg OVRD Actv Emergency Override Activated

Alarm 1 4 Energy Pause Cfg Invalid Energy Pause Configuration

Resettable Fault 6 SecureEraseCplt Secure Erase Complete

Event 7 EmergOVRD Actv Emergency Override Activated

Resettable Fault 17 CPU OverTemp Flt CPU Over Temperature Fault

Resettable Fault 18 System Defaulted System Defaulted

Event 21 Clr Fault Queue Clear Fault Queue

Alarm 1 24 Board OT Alarm Control Board Overtemperature

Alarm 1 26 Board UT Alarm Control Board Undertemperature

Resettable Fault 27 Module Defaulted Module Defaulted

Resettable Fault 29 Port 1 Adapter Port 1 Adapter

Resettable Fault 30 Port 2 Adapter Port 2 Adapter

Resettable Fault 31 Port 3 Adapter Port 3 Adapter

Resettable Fault 33 Port 5 Adapter Port 5 Adapter

Resettable Fault 34 Port 6 Adapter Port 6 Adapter

Configurable 35 Port 1 DPI Loss Port 1 DPI Loss

Configurable 36 Port 2 DPI Loss Port 2 DPI Loss

Configurable 37 Port 3 DPI Loss Port 3 DPI Loss

Resettable Fault 39 Port 5 DPI Loss Port 5 DPI Loss

Resettable Fault 40 Port 6 DPI Loss Port 6 DPI Loss

Resettable Fault 43 PwrDn NVS Blank Power Down NVS Blank

Non-Resettable 58 PwrDn Data Chksm Power Down Data Checksum

Event 60 New Firmware New Firmware

Event 62 RTC HW Failed RTC Hardware Access Failed

Event 63 Time Change Time Change Event

Event 65 Time Chg Cnt Ovf Time Change Count Overflow

Resettable Fault 67 PwrDn Data Fail Power Down Data Failure

Alarm 1 68 PwrDn Sig Fail Power Down Signal Failure

Event 69 Cond Data Lost Condition Data Corrupt

Event 70 Firmware Update Firmware Update

Resettable Fault 72 Digin Regen Fail Digital Input Regeneration Failure

Alarm 2 73 DigIn Cfg B Digital Input Configuration B

Alarm 2 74 DigIn Cfg C Digital Input Configuration C

Event 77 Drive Reset Drive Reset

Event 80 Drive Faulted Drive Faulted

Resettable Fault 86 HW Enbl Jmpr Out Hardware Enable Jumper Out

Non-Resettable 88 Safety Jmpr Out Safety Jumper Out

Non-Resettable 89 Safety Jumper In Safety Jumper In

Non-Resettable 92 SafetyHealth Err SafetyHealth Error

Non-Resettable 93 SafetyPwrOn Err SafetyPwrOn Error

Non-Resettable 95 FS Enbl Ch Error FS Enable Channel Error

Alarm 2 104 Port 4 Cfg Port 4 Configuration

Alarm 2 105 Port 5 Cfg Port 5 Configuration

Alarm 2 106 Port 6 Cfg Port 6 Configuration

Alarm 2 107 Port 7 Cfg Port 7 Configuration

Alarm 2 108 Port 8 Cfg Port 8 Configuration

Alarm 2 112 Port 12 Cfg Port 12 Configuration

Non-Resettable 128 LC Incomp PFB Liquid Cooled Incompatible Power

Event 129 Prev Maint Reset Predictive Maintenance Reset

Configurable 132 Pod Fan Life Control Pod Fan Life

Configurable 135 CtrlBay Fan Life Control Bay Fan Life

Resettable Fault 171 No Stop Source All Logic Control Sources

Alarm 2 176 InvldDataSource Invalid Indirect Selection

Configurable 177 NonStdDataSource Non Standard Data Source

Alarm 2 180 Invld 2Wire Cfg Invalid 2 Wire Configuration