BAS3007A...

Low VF Schottky Diode Array

• Reverse voltage: 30 V
• Forward current: 0.9 A
• Small diode quad array for polarity independence,
reverse polarity protection and low loss
bridge rectification
• Very low forward voltage:
0.5 V typ. @ 0.7 A (per diode)
• Fast switching
• Pb-free (ROHS compliant) package 1)
• Qualified according AEC Q101

BAS3007A-RPP
+ 4 3 ~
D3

D4 D2

D1

- 1 2 ~

Type Package Configuration Marking

BAS3007A-RPP SOT143 bridge E1s
Maximum Ratings at TA = 25°C, unless otherwise specified
Parameter Symbol Value Unit
Diode reverse voltage2) VR 30 V
Peak reverse voltage2) VRM 30
RMS reverse voltage2) VR(RMS) 21
Forward current 2) IF mA
TS ≤ 46°C 900
TS ≤ 82°C 700
Non-repetitive peak surge forward current I FSM 5 A
(t ≤ 10 ms)
Junction temperature Tj 150 °C
Storage temperature T stg -65 ... 150
1Pb-containing package may be available upon special request
2For TA > 25°C the derating of VR and IF has to be considered. Please refer to the attached curves.

1 2007-11-20
 BAS3007A...

Thermal Resistance
Parameter Symbol Value Unit
Junction - soldering point 1) RthJS ≤ 95 K/W

Electrical Characteristics at TA = 25°C, unless otherwise specified

Parameter Symbol Values Unit
min. typ. max.
DC Characteristics
Reverse current (per diode)2) IR µA
VR = 12 V - - 30
VR = 30 V - - 350
Forward voltage (per diode)2)3) VF V
IF = 100 mA - 0.35 0.4
IF = 350 mA - 0.4 0.5
IF = 500 mA - 0.45 0.55
IF = 700 mA - 0.5 0.6
IF = 900 mA - 0.6 0.7

AC Characteristics
Diode capacitance (per diode) CT - 9 15 pF
VR = 5 V, f = 1 MHz
1For calculation of RthJA please refer to Application Note Thermal Resistance
2Pulsed test, tp = 300 µs; D = 0.01
3When used as shown for Reverse Polarity Protection (RPP, see page 4), the voltage available to the circuit
being protected will be two diode drops below the power supply voltage. In other words, the supply current
will pass through two diodes.

2 2007-11-20
 BAS3007A...

Diode capacitance CT = ƒ (VR) Forward Voltage VF = ƒ (TA)

f = 1MHz (per diode) IF = Parameter (per diode)

30 0.7
pF V

IF = 900mA
26 0.6

24 0.55 IF = 700mA

22 0.5

0.45
CT

VF
20 IF = 350mA
0.4
18
0.35
16 IF = 100mA
0.3
14
0.25
12
0.2
10
0.15
8 0.1
6 0.05

4 0
0 5 10 15 20 V 30 -45 -15 15 45 75 °C 135
VR TA

Forward current IF = ƒ (VF) Permissible Reverse voltage VR = ƒ (TA)

TA = Parameter (per diode) tp = Paramter, Duty cycle < 0.01
Device mounted on PCB with Rth = 160 K/W
10 0 35

+125°C 25
VRmax

+85°C
+25°C
IF

-40°C DC
20
A
20 ms
1 ms

15

10

10 -1 0
0.15 0.25 0.35 0.45 V 0.65 0 20 40 60 80 100 °C 130
VF TA

3 2007-11-20
 BAS3007A...

Forward current IF = ƒ (T S)
Current flows through two chips
per package at the same time (per array)
1000

mA

800

700
IF

600

500

400

300

200

100

0
0 15 30 45 60 75 90 105 120 °C 150
TS

Application example BAS3007A-RPP

Advanced Reverse Polarity Protection(RPP): due to diode orientation, circuit at the right
will be protected from damage and will also function normally in the event reverse polarity is
applied to pins 2 and 3 of the BAS3007A-RPP.

Ground
Ground /
+Vs 2 1

DC Plug to Reverse polarity

power supply protected circuit

+Vs / 3 4
Ground
+Vs

4 2007-11-20
 Package SOT143 BAS3007A...

Package Outline

0.15 MIN.
2.9 ±0.1 1 ±0.1
B
1.9 0.1 MAX.

4 3

2.4 ±0.15

1.3 ±0.1
10˚ MAX.

10˚ MAX.
1 2
0.2 0.08...0.1 A
5
0.8 +0.1
-0.05
0...8˚
0.4 +0.1
-0.05
0.25 M B 0.2 M A
1.7

Foot Print

0.8 1.2 0.8 0.9

1.1
0.9

1.2 0.8
0.8

Marking Layout (Example)

Manufacturer
56

RF s 2005, June
Date code (YM)

Pin 1 BFP181
Type code

Standard Packing
Reel ø180 mm = 3.000 Pieces/Reel
Reel ø330 mm = 10.000 Pieces/Reel

4 0.2
8
2.6

Pin 1 3.15 1.15

5 2007-11-20
 BAS3007A...

Edition 2006-02-01
Published by
Infineon Technologies AG
81726 München, Germany
© Infineon Technologies AG 2007.
All Rights Reserved.

Attention please!

The information given in this dokument shall in no event be regarded as a guarantee

of conditions or characteristics (“Beschaffenheitsgarantie”). With respect to any
examples or hints given herein, any typical values stated herein and/or any information
regarding the application of the device, Infineon Technologies hereby disclaims any
and all warranties and liabilities of any kind, including without limitation warranties of
non-infringement of intellectual property rights of any third party.

Information

For further information on technology, delivery terms and conditions and prices
please contact your nearest Infineon Technologies Office (www.infineon.com).

Warnings

Due to technical requirements components may contain dangerous substances.

For information on the types in question please contact your nearest
Infineon Technologies Office.
Infineon Technologies Components may only be used in life-support devices or
systems with the express written approval of Infineon Technologies, if a failure of
such components can reasonably be expected to cause the failure of that
life-support device or system, or to affect the safety or effectiveness of that
device or system.
Life support devices or systems are intended to be implanted in the human body,
or to support and/or maintain and sustain and/or protect human life. If they fail,
it is reasonable to assume that the health of the user or other persons
may be endangered.

6 2007-11-20