® INA1

28 INA1
29 INA128
INA1
28
INA1
29
INA129

Precision, Low Power

INSTRUMENTATION AMPLIFIERS
FEATURES DESCRIPTION
● LOW OFFSET VOLTAGE: 50µV max The INA128 and INA129 are low power, general
● LOW DRIFT: 0.5µV/°C max purpose instrumentation amplifiers offering excellent
accuracy. Their versatile 3-op amp design and small
● LOW INPUT BIAS CURRENT: 5nA max
size make them ideal for a wide range of applications.
● HIGH CMR: 120dB min Current-feedback input circuitry provides wide band-
● INPUTS PROTECTED TO ±40V width even at high gain (200kHz at G = 100).
● WIDE SUPPLY RANGE: ±2.25 to ±18V A single external resistor sets any gain from 1 to
● LOW QUIESCENT CURRENT: 700µA 10,000. INA128 provides an industry standard gain
equation; INA129’s gain equation is compatible with
● 8-PIN PLASTIC DIP, SO-8
the AD620.
The INA128/INA129 is laser trimmed for very low
APPLICATIONS offset voltage (50µV), drift (0.5µV/°C) and high com-
mon-mode rejection (120dB at G ≥ 100). It operates
● BRIDGE AMPLIFIER with power supplies as low as ±2.25V, and quiescent
● THERMOCOUPLE AMPLIFIER current is only 700µA—ideal for battery operated
● RTD SENSOR AMPLIFIER systems. Internal input protection can withstand up to
±40V without damage.
● MEDICAL INSTRUMENTATION
● DATA ACQUISITION The INA128/INA129 is available in 8-pin plastic
DIP, and SO-8 surface-mount packages, specified for
the –40°C to +85°C temperature range. The INA128
is also available in dual configuration, the INA2128.
V+

7
INA128:
INA128, INA129 50kΩ
– 2 Over-Voltage G=1+
VIN RG
Protection
A1
40kΩ 40kΩ INA129:
1 49.4kΩ
G=1+
25kΩ(1) RG

6
RG A3 VO

8
25kΩ(1)

5
A2 Ref
+ 3 Over-Voltage
VIN 40kΩ 40kΩ
Protection

4
NOTE: (1) INA129: 24.7kΩ
V–

International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111
Internet: http://www.burr-brown.com/ • FAXLine: (800) 548-6133 (US/Canada Only) • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132

©1995 Burr-Brown Corporation PDS-1296C Printed in U.S.A. October, 1996

SPECIFICATIONS
At TA = +25°C, VS = ±15V, RL = 10kΩ, unless otherwise noted.

INA128P, U INA128PA, UA
INA129P, U INA129PA, UA
PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS
INPUT
Offset Voltage, RTI
Initial TA = +25°C ±10 ±100/G ±50 ±500/G ±25 ±100/G ±125 ±1000/G µV
vs Temperature TA = TMIN to TMAX ±0.2 ± 2/G ±0.5 ± 20/G ±0.2 ± 5/G ±1 ± 20/G µV/°C
vs Power Supply VS = ±2.25V to ±18V ±0.2 ±20/G ±1 ±100/G ✻ ±2 ±200/G µV/V
Long-Term Stability ±0.1 ±3/G ✻ µV/mo
Impedance, Differential 1010 || 2 ✻ Ω || pF
Common-Mode 1011 || 9 ✻ Ω || pF
Common-Mode Voltage Range(1) VO = 0V (V+) – 2 (V+) – 1.4 ✻ ✻ V
(V–) + 2 (V–) + 1.7 ✻ ✻ V
Safe Input Voltage ±40 ✻ V
Common-Mode Rejection VCM = ±13V, ∆RS = 1kΩ
G=1 80 86 73 ✻ dB
G=10 100 106 93 ✻ dB
G=100 120 125 110 ✻ dB
G=1000 120 130 110 ✻ dB
BIAS CURRENT ±2 ±5 ✻ ±10 nA
vs Temperature ±30 ✻ pA/°C
Offset Current ±1 ±5 ✻ ±10 nA
vs Temperature ±30 ✻ pA/°C
NOISE VOLTAGE, RTI G = 1000, RS = 0Ω
f = 10Hz 10 ✻ nV/√Hz
f = 100Hz 8 ✻ nV/√Hz
f = 1kHz 8 ✻ nV/√Hz
fB = 0.1Hz to 10Hz 0.2 ✻ µVp-p
Noise Current
f=10Hz 0.9 ✻ pA/√Hz
f=1kHz 0.3 ✻ pA/√Hz
fB = 0.1Hz to 10Hz 30 ✻ pAp-p
GAIN
Gain Equation, INA128 1 + (50kΩ/RG) ✻ V/V
INA129 1 + (49.4kΩ/RG) ✻ V/V
Range of Gain 1 10000 ✻ ✻ V/V
Gain Error G=1 ±0.01 ±0.024 ✻ ±0.1 %
G=10 ±0.02 ±0.4 ✻ ±0.5 %
G=100 ±0.05 ±0.5 ✻ ±0.7 %
G=1000 ±0.5 ±1 ✻ ±2 %
Gain vs Temperature(2) G=1 ±1 ±10 ✻ ✻ ppm/°C
50kΩ (or 49.4kΩ) Resistance(2, 3) ±25 ±100 ✻ ✻ ppm/°C
Nonlinearity VO = ±13.6V, G=1 ±0.0001 ±0.001 ✻ ±0.002 % of FSR
G=10 ±0.0003 ±0.002 ✻ ±0.004 % of FSR
G=100 ±0.0005 ±0.002 ✻ ±0.004 % of FSR
G=1000 ±0.001 (Note 4) ✻ ✻ % of FSR
OUTPUT
Voltage: Positive RL = 10kΩ (V+) – 1.4 (V+) – 0.9 ✻ ✻ V
Negative RL = 10kΩ (V–) + 1.4 (V–) + 0.8 ✻ ✻ V
Load Capacitance Stability 1000 ✻ pF
Short-Circuit Current +6/–15 ✻ mA
FREQUENCY RESPONSE
Bandwidth, –3dB G=1 1.3 ✻ MHz
G=10 700 ✻ kHz
G=100 200 ✻ kHz
G=1000 20 ✻ kHz
Slew Rate VO = ±10V, G=10 4 ✻ V/µs
Settling Time, 0.01% G=1 7 ✻ µs
G=10 7 ✻ µs
G=100 9 ✻ µs
G=1000 80 ✻ µs
Overload Recovery 50% Overdrive 4 ✻ µs
POWER SUPPLY
Voltage Range ±2.25 ±15 ±18 ✻ ✻ ✻ V
Current, Total VIN = 0V ±700 ±750 ✻ ✻ µA
TEMPERATURE RANGE
Specification –40 85 ✻ ✻ °C
Operating –40 125 ✻ ✻ °C
θJA 8-Pin Dip 80 ✻ °C/W
SO-8 SOIC 150 ✻ °C/W

✻ Specification same as INA128P, U or INA129P, U.

NOTE: (1) Input common-mode range varies with output voltage—see typical curves. (2) Guaranteed by wafer test. (3) Temperature coefficient of the 50kΩ (or 49.4kΩ)
term in the gain equation. (4) Nonlinearity measurements in G = 1000 are dominated by noise. Typical nonlinearity is ±0.001%.
PIN CONFIGURATION ELECTROSTATIC
8-Pin DIP and SO-8 DISCHARGE SENSITIVITY
Top View This integrated circuit can be damaged by ESD. Burr-Brown
RG 1 8 RG
recommends that all integrated circuits be handled with ap-
propriate precautions. Failure to observe proper handling and
V–IN 2 7 V+ installation procedures can cause damage.
V+IN 3 6 VO ESD damage can range from subtle performance degradation
V– 4 5 Ref to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
ABSOLUTE MAXIMUM RATINGS
Supply Voltage .................................................................................. ±18V ORDERING INFORMATION
Analog Input Voltage Range ............................................................. ±40V
PACKAGE
Output Short-Circuit (to ground) .............................................. Continuous
DRAWING TEMPERATURE
Operating Temperature ................................................. –40°C to +125°C
PRODUCT PACKAGE NUMBER(1) RANGE
Storage Temperature ..................................................... –40°C to +125°C
Junction Temperature .................................................................... +150°C INA128PA 8-Pin Plastic DIP 006 –40°C to +85°C
Lead Temperature (soldering, 10s) ............................................... +300°C INA128P 8-Pin Plastic DIP 006 –40°C to +85°C
INA128UA SO-8 Surface-Mount 182 –40°C to +85°C
INA128U SO-8 Surface-Mount 182 –40°C to +85°C
INA129PA 8-Pin Plastic DIP 006 –40°C to +85°C
INA129P 8-Pin Plastic DIP 006 –40°C to +85°C
INA129UA SO-8 Surface-Mount 182 –40°C to +85°C
INA129U SO-8 Surface-Mount 182 –40°C to +85°C

NOTE: (1) For detailed drawing and dimension table, please see end of data
sheet, or Appendix C of Burr-Brown IC Data Book.

The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility
for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or
licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support
devices and/or systems.
 TYPICAL PERFORMANCE CURVES
At TA = +25°C, VS = ±15V, unless otherwise noted.

GAIN vs FREQUENCY COMMON-MODE REJECTION vs FREQUENCY

60 140
G = 1000V/V G = 1000V/V
50 G = 100V/V

Common-Mode Rejection (dB)

120
G = 10V/V
40
G = 100V/V 100
30 G = 1V/V
Gain (dB)

80
20
G = 10V/V 60
10
40
0
G = 1V/V
–10 20

–20 0
1k 10k 100k 1M 10M 10 100 1k 10k 100k 1M
Frequency (Hz) Frequency (Hz)

POSITIVE POWER SUPPLY REJECTION NEGATIVE POWER SUPPLY REJECTION

vs FREQUENCY vs FREQUENCY
140 140
G = 1000V/V
120 120
G = 100V/V
Power Supply Rejection (dB)

G = 1000V/V
Power Supply Rejection (dB)

100 100
G = 100V/V
80 80

60 60 G = 10V/V

G = 10V/V
40 40 G = 1V/V
G = 1V/V
20 20

0 0
10 100 1k 10k 100k 1M 10 100 1k 10k 100k 1M
Frequency (Hz) Frequency (Hz)

INPUT COMMON-MODE RANGE INPUT COMMON-MODE RANGE

vs OUTPUT VOLTAGE, VS = ±15V vs OUTPUT VOLTAGE, VS = ±5, ±2.5V
15 5
G ≥ 10 G ≥ 10
4 G ≥ 10 G ≥ 10
10
Common-Mode Voltage (V)

Common-Mode Voltage (V)

3
G=1 G=1 G=1 G=1
2
5 G ≥ 10
+15V 1
–
VD/2 VO
0 + 0 G=1
–
VD/2 –1
+ + Ref
–5 VCM –2
–15V
–3
–10 VS = ±5V
–4 VS = ±2.5V
–15 –5
–15 –10 –5 0 5 10 15 –5 –4 –3 –2 –1 0 1 2 3 4 5
Output Voltage (V) Output Voltage (V)
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, VS = ±15V, unless otherwise noted.

INPUT- REFERRED NOISE vs FREQUENCY SETTLING TIME vs GAIN

1k 100 100
Input-Referred Voltage Noise (nV/√ Hz)

Input Bias Current Noise (pA/√ Hz)

0.01%
G = 1V/V

Settling Time (µs)

100 10

0.1%
10
G = 10V/V
10 1
G = 100, 1000V/V

Current Noise

1 0.1 1
1 10 100 1k 10k 1 10 100 1000
Frequency (Hz) Gain (V/V)

QUIESCENT CURRENT and SLEW RATE

vs TEMPERATURE INPUT OVER-VOLTAGE V/I CHARACTERISTICS
0.85 6 5
4
0.8 5 3
Flat region represents
Quiescent Current (µA)

Input Current (mA)

2 normal linear operation.

Slew Rate (V/µs)

G = 1000V/V
0.75 4 1
G = 1V/V
Slew Rate 0
0.7 3 –1 +15V
G = 1V/V
–2
IQ
0.65 2 –3
G = 1000V/V VIN
–4 IIN
–15V
0.6 1 –5
–75 –50 –25 0 25 50 75 100 125 –50 –40 –30 –20 –10 0 10 20 30 40 50
Temperature (°C) Input Voltage (V)

INPUT OFFSET VOLTAGE WARM-UP INPUT BIAS CURRENT vs TEMPERATURE

10 2
8
Offset Voltage Change (µV)

6
Input Bias Current (nA)

1
4
2 IOS
0 0

–2
IB
–4
–1
–6 Typical IB and IOS
–8 Range ±2nA at 25°C

–10 –2
0 100 200 300 400 500
–75 –50 –25 0 25 50 75 100 125
Time (µs) Temperature (°C)
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, VS = ±15V, unless otherwise noted.

OUTPUT VOLTAGE SWING OUTPUT VOLTAGE SWING

vs OUTPUT CURRENT vs POWER SUPPLY VOLTAGE
(V+) V+

(V+)–0.4 (V+)–0.4

Output Voltage Swing (V)

+25°C +85°C
(V+)–0.8
(V+)–0.8
Output Voltage (V)

(V+)–1.2 –40°C
(V+)–1.2
RL = 10kΩ
(V–)+1.2 +25°C
(V+)+1.2
–40°C
(V–)+0.8
(V–)+0.8 +85°C +85°C
–40°C
(V–)+0.4 (V–)+0.4

V– V–
0 1 2 3 4 0 5 10 15 20
Output Current (mA) Power Supply Voltage (V)

SHORT-CIRCUIT OUTPUT CURRENT

vs TEMPERATURE MAXIMUM OUTPUT VOLTAGE vs FREQUENCY
18 30
G = 10, 100
Peak-to-Peak Output Voltage (Vpp)

16 –ISC 25 G=1
Short Circuit Current (mA)

14
G = 1000
12 20

10
15
8

6 10
+ISC
4
5
2
0 0
–75 –50 –25 0 25 50 75 100 125 1k 10k 100k 1M
Temperature (°C) Frequency (Hz)

TOTAL HARMONIC DISTORTION + NOISE

vs FREQUENCY
1
VO = 1Vrms G=1
500kHz Measurement RL = 10kΩ
Bandwidth

0.1 G = 100, RL = 100kΩ

THD + N (%)

0.01
G = 10V/V
G = 1, RL = 100kΩ
RL = 100kΩ
Dashed Portion
is noise limited.
0.001
100 1k 10k 100k
Frequency (Hz)
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, VS = ±15V, unless otherwise noted.

SMALL-SIGNAL SMALL-SIGNAL
(G = 1, 10) (G = 100, 1000)

G=1 G = 100

20mV/div 20mV/div

G = 10 G = 1000

5µs/div 20µs/div

LARGE-SIGNAL LARGE-SIGNAL
(G = 1, 10) (G = 100, 1000)

G=1 G = 100

5V/div 5V/div

G = 10 G = 1000

5µs/div 20µs/div

VOLTAGE NOISE 0.1 to 10Hz

INPUT-REFERRED, G ≥ 100

0.1µV/div

1s/div
APPLICATION INFORMATION
Figure 1 shows the basic connections required for operation accurate absolute values. The accuracy and temperature
of the INA128/INA129. Applications with noisy or high coefficient of these internal resistors are included in the gain
impedance power supplies may require decoupling capaci- accuracy and drift specifications of the INA128/INA129.
tors close to the device pins as shown. The stability and temperature drift of the external gain
The output is referred to the output reference (Ref) terminal setting resistor, RG, also affects gain. RG’s contribution to
which is normally grounded. This must be a low-impedance gain accuracy and drift can be directly inferred from the gain
connection to assure good common-mode rejection. A resis- equation (1). Low resistor values required for high gain can
tance of 8Ω in series with the Ref pin will cause a typical make wiring resistance important. Sockets add to the wiring
device to degrade to approximately 80dB CMR (G = 1). resistance which will contribute additional gain error (possi-
bly an unstable gain error) in gains of approximately 100 or
SETTING THE GAIN greater.
Gain is set by connecting a single external resistor, RG,
connected between pins 1 and 8: DYNAMIC PERFORMANCE
The typical performance curve “Gain vs Frequency” shows
INA128: 50kΩ (1) that, despite its low quiescent current, the INA128/INA129
G = 1+
RG achieves wide bandwidth, even at high gain. This is due to
the current-feedback topology of the input stage circuitry.
INA129: 49. 4kΩ (2) Settling time also remains excellent at high gain.
G = 1+
RG
NOISE PERFORMANCE
Commonly used gains and resistor values are shown in
The INA128/INA129 provides very low noise in most appli-
Figure 1.
cations. Low frequency noise is approximately 0.2µVp-p
The 50kΩ term in Equation 1 (49.4kΩ in Equation 2) comes measured from 0.1 to 10Hz (G ≥ 100). This provides
from the sum of the two internal feedback resistors of A1 and dramatically improved noise when compared to state-of-the-
A2. These on-chip metal film resistors are laser trimmed to art chopper-stabilized amplifiers.

V+

0.1µF

INA128: INA129:
50kΩ 49.4kΩ 7
G=1+ G=1+
RG RG INA128, INA129
– 2 Over-Voltage
VIN
Protection
INA128 INA129 A1
40kΩ 40kΩ
DESIRED RG NEAREST RG NEAREST 1 + –
GAIN (V/V) (Ω) 1% RG (Ω) (Ω) 1% RG (Ω) 25kΩ(1) VO = G • (VIN – VIN )
1 NC NC NC NC 6
RG A3
2 50.00k 49.9k 49.4k 49.9k
5 12.50k 12.4k 12.35k 12.4k +
8
10 5.556k 5.62k 5489 5.49k 25kΩ(1) Load VO
20 2.632k 2.61k 2600 2.61k –
50 1.02k 1.02k 1008 1k 5
A2
100 505.1 511 499 499 + 3 Over-Voltage Ref
VIN 40kΩ 40kΩ
200 251.3 249 248 249 Protection
500 100.2 100 99 100
1000 50.05 49.9 49.5 49.9 4 0.1µF
2000 25.01 24.9 24.7 24.9
5000 10.00 10 9.88 9.76 NOTE: (1) INA129: 24.7kΩ
10000 5.001 4.99 4.94 4.87
V–
NC: No Connection.
Also drawn in simplified form:

–
VIN

RG INA128 VO

+ Ref
VIN

FIGURE 1. Basic Connections.

OFFSET TRIMMING
The INA128/INA129 is laser trimmed for low offset voltage
and offset voltage drift. Most applications require no exter-
nal offset adjustment. Figure 2 shows an optional circuit for Microphone,
Hydrophone INA128
trimming the output offset voltage. The voltage applied to etc.
Ref terminal is summed with the output. The op amp buffer
provides low impedance at the Ref terminal to preserve good
47kΩ 47kΩ
common-mode rejection.

–
VIN Thermocouple INA128
V+
RG INA128 VO
100µA
Ref 1/2 REF200
V+IN 10kΩ

10kΩ 100Ω
OPA177
±10mV
Adjustment Range
100Ω INA128

100µA
1/2 REF200 Center-tap provides
bias current return.
V–

FIGURE 2. Optional Trimming of Output Offset Voltage. FIGURE 3. Providing an Input Common-Mode Current Path.

INPUT BIAS CURRENT RETURN PATH linear common-mode input range is related to the output
The input impedance of the INA128/INA129 is extremely voltage of the complete amplifier. This behavior also de-
high—approximately 1010Ω. However, a path must be pro- pends on supply voltage—see performance curves “Input
vided for the input bias current of both inputs. This input Common-Mode Range vs Output Voltage”.
bias current is approximately ±2nA. High input impedance Input-overload can produce an output voltage that appears
means that this input bias current changes very little with normal. For example, if an input overload condition drives
varying input voltage. both input amplifiers to their positive output swing limit, the
Input circuitry must provide a path for this input bias current difference voltage measured by the output amplifier will be
for proper operation. Figure 3 shows various provisions for near zero. The output of A3 will be near 0V even though both
an input bias current path. Without a bias current path, the inputs are overloaded.
inputs will float to a potential which exceeds the common-
mode range, and the input amplifiers will saturate. LOW VOLTAGE OPERATION
If the differential source resistance is low, the bias current The INA128/INA129 can be operated on power supplies as
return path can be connected to one input (see the thermo- low as ±2.25V. Performance remains excellent with power
couple example in Figure 3). With higher source impedance, supplies ranging from ±2.25V to ±18V. Most parameters
using two equal resistors provides a balanced input with vary only slightly throughout this supply voltage range—see
possible advantages of lower input offset voltage due to bias typical performance curves. Operation at very low supply
current and better high-frequency common-mode rejection. voltage requires careful attention to assure that the input
voltages remain within their linear range. Voltage swing
INPUT COMMON-MODE RANGE requirements of internal nodes limit the input common-
mode range with low power supply voltage. Typical perfor-
The linear input voltage range of the input circuitry of the
mance curves, “Input Common-Mode Range vs Output
INA128/INA129 is from approximately 1.4V below the
Voltage” show the range of linear operation for ±15V, ±5V,
positive supply voltage to 1.7V above the negative supply.
and ±2.5V supplies.
As a differential input voltage causes the output voltage
increase, however, the linear input range will be limited by
the output voltage swing of amplifiers A1 and A2. So the
 RG = 5.6kΩ

2.8kΩ
G = 10
VO
LA RG/2 INA128
RA
Ref
2.8kΩ
390kΩ VG
VG 1/2
1/2 OPA2131 NOTE: Due to the INA128’s current-feedback
RL OPA2131 10kΩ topology, VG is approximately 0.7V less than
390kΩ the common-mode input voltage. This DC offset
in this guard potential is satisfactory for many
guarding applications.

FIGURE 4. ECG Amplifier With Right-Leg Drive.

V+
+5V 10.0V 6
REF102 2
2.5V – ∆V
R1 R2

RG INA128 VO 4
300Ω
Ref
2.5V + ∆V Pt100

Cu
K VO
Cu RG INA128

R3 Ref

FIGURE 5. Bridge Amplifier. 100Ω = Pt100 at 0°C

SEEBECK
ISA COEFFICIENT
– TYPE MATERIAL (µV/°C) R1, R2
VO
VIN RG INA128 E + Chromel 58.5 66.5kΩ
+ – Constantan
Ref R1 J + Iron 50.2 76.8kΩ
C1
1MΩ – Constantan
0.1µF
K + Chromel 39.4 97.6kΩ
– Alumel
T + Copper 38.0 102kΩ
1 – Constantan
f–3dB =
OPA130 2πR1C1
= 1.59Hz
FIGURE 7. Thermocouple Amplifier With RTD Cold-
Junction Compensation.

FIGURE 6. AC-Coupled Instrumentation Amplifier.

– VIN
R1 IO = •G
R1
VIN RG INA128
+
Ref
IB

A1 IO
Load
A1 IB Error
OPA177 ±1.5nA
OPA131 ±50pA
OPA602 ±1pA
OPA128 ±75fA

FIGURE 8. Differential Voltage to Current Converter.