Roof Plan 5

PROJECT NAME
CLIENT:
DRAWING LIST HARVINDER D. 13948 Mississauga
Sheet CALEDON, ON Road, Caledon ON
Number Sheet Name
PROJECT ADDRESS
0-COVER 13948 Mississauga Road, Caledon

A-000 COVER SHEET ARCHITECT: ON
KHALSA DESIGN INC.
1-SITE PLAN
ASP-1 SITE PLAN
BRAMPTON, ON CLIENT
2-CIVIL HARVINDER D.
SG-1 SITE GRADING PLAN STRUCTURAL: RESIDENCE
SP-1 SEPTIC DESIGN
MEM ENGINEERING
ARCHITECT
3-ARCHITECTURAL BRAMPTON, ON
A-001 CONSTRUCTION NOTES
KHALSA DESIGN INC.
A-101 BASEMENT FLOOR PLAN
A-102 GROUND FLOOR PLAN SURVERYOR:
A-103 SECOND FLOOR PLAN
A-104 ROOF PLAN
Y. ZHANG SURVEYING
A-301 FRONT & REAR ELEVATION MARKHAM, ON
A-302 SIDE ELEVATIONS
A-400a BUILDING SECTIONS
A-400b BUILDING SECTIONS
GRADING & SEPTIC:
A-401 TYPICAL DETAILS
A-402 TYPICAL DETAILS
LAND BUILDING EXPERTS
A-403 TYPICAL DETAILS MARKHAM, ON
4-HVAC
HVAC-1 BASEMENT HVAC LAYOUT BRAMPTON, ON
MECHANICAL:
HVAC-2 GROUND FLOOR HVAC LAYOUT
HVAC-3 SECOND FLOOR HVAC LAYOUT GLS HVAC DESIGN TELEPHONE: 647-468-2940
MT. HOPE, ON
CONSULTANTS:
5-FLOOR LAYOUT
F1 GROUND FLOOR FRAMING LAYOUT STRUCTURAL ENGINEER:
MEM ENGINEERING INC.
F2 SECOND FLOOR FRAMING LAYOUT
FLOOR MANUFACTURER: STRUCUTRAL SEAL:
6-TRUSS LAYOUT PHOENIX BUILDING
R1 ROOF TRUSS LAYOUT
13948 Mississauga COMPONENTS
NEW LOWELL, ON
Road, Caledon ON TRUSS MANUFACTURER:

PHOENIX BUILDING
PERMIT SET COMPONENTS
NEW LOWELL, ON
COPYRIGHT KDI © 2023

THESE DRAWINGS ARE NOW AND DO
REMAIN THE SOLE PROPERTY OF KHALSA
DESIGN USE OF THESE PLANS OR ANY
FORM OF REPRODUCTION OF THIS DESIGN
IN WHOLE OR IN PART WITHOUT EXPRESS
LOCUS MAP - ZONE A1 (RR) WRITTEN CONSENT IS PROHIBITED AND
SHALL RESULT IN THE FULLEST EXTENT OF
PROSECUTION UNDER LAW
ARCHITECT SEAL:
05 - 02 - 2024
AREA CALCULATIONS DESIGN

SB-12 ENERGY EFFICIENCY DESIGN SUMMARY GROUND FLOOR AREA 4590 sq ft Project number 24003
SECOND FLOOR AREA 3452 sq ft Date 05/02/2024
PERSCRIPTIVE COMPLIANCE SB-12 (SECTION 3.1.1)
Drawn by ASB
SPACE HEATING FUEL SUBTOTAL 8042 sq ft Checked by KDI
SUBJECT
PROPERTY
PACKAGE A1 GAS
ELECTRIC
EARTH
OIL
PROPANE
SOLID FUEL
DEDUCT ALL OPEN AREAS 1305 sq ft
Scale
TOTAL NET AREA 6737 sq ft REVISIONS

(625.89 sq m)
BUILDING COMPONENT REQUIRED PROPOSED
No. Description Date
INSULATION RSI (R) VALUE FINISHED BSMT. AREA 0 sq ft
CEILING W/ ATTIC SPACE 10.56 (R60) 10.56 (R60)
1
CEILING W/O ATTIC SPACE 5.46 (R31) 5.46 (R31) COVERAGE 7826 sq ft
EXPOSED FLOOR 5.46 (R31) 5.46 (R31) W/OUT PORCH (727.06 sq m)
WALLS ABOVE GRADE 3.87 (R22) 3.87 (R22) COVERAGE 8418 sq ft
W/PORCH (782.06 sq m)
BASEMENT WALLS 3.52 ci 3.52 ci
(R20 ci) (R20 ci) WINDOW/WALL AREA DESIGN
BELOW GRADE SLAB ENTIRE SURFACE >600mm BELOW GRADE - - CALCULATIONS
EDGE OF BELOW GRADE SLAB < 600mm BELOW GRADE 1.76 (R10) 1.76 (R10) GROSS WALL AREA 7893 sq ft
(733.28 sq m)
HEATED SLAB < 600mm BELOW GRADE 1.76 (R10) 1.76 (R10) GROSS WINDOW AREA 1635 sq ft
(151.90 sq m)
WINDOWS & DOORS
TOTAL NET AREA 20.71 %
WINDOWS SLIDING GLASS DOORS (MAX U-VALUE / MIN. ER) 1.6 1.6
SKYLIGHTS (MAX. U-VALUE) 2.8 2.8
APPLIANCE EFFICIENCY
SPACE HEATING EQUIP. (AFUE%) 96% 96%
HRV. EFFICIENCY (%) 75% 75%
DHW HEATER (EF) 0.8 0.8 COVER SHEET
NOTE: AS PER OBC SB-12 3.1.1.1.(8) OVERALL COEFFICENT OF HEAT TRANSFER OF
THE FENESTRATION SHALL BE UPGRADED TO 1.4
A-000
13948 Mississauga Road, Caledon
ON
8-0080 (LT)
NING
D BASE
SITE PLAN APPLICATION NO. PROJECT NAME
SURVEY NOTE: SITE STATSTICS
EXISTING TOPOGRAPHIC SURVEY
INFORMATION TAKEN FROM ZONE A1 (RR AS PER 10.4.1)
-
SURVEY PREPARED BY Y.ZHANG RR PROPOSED LOT 27 13948 Mississauga
SURVEYING LIMITED LOT AREA 1390 m² 1949.35 m² CONCESSION 5
LO
POST&WIRE FENCE
28
Road, Caledon ON
3.2
LOT FRONTAGE 21.00 m 63.40 m
TOWN OF CALEDON
1
28
28
GRADING NOTE: BUILDING AREA
REGION OF PEEL
2.9
28
2.3
28
REFER TO GRADING PLAN FOR PROJECT ADDRESS
1.0
25% 24.2%
3.4
3
2
DETAILS PREPARED BY LAND
1
FRONT YARD 9.0 m 35.62 m
0.15SW
0.24SE
FENCE
BUILDING EXPERTS EXTERIOR SIDE YARD N/A N/A
(N45°30'40"W D1) 13948 Mississauga Road, Caledon
SIDE YARD (DRIVEWAY SIDE) 3.0 m 6.29 m
(D1&MEAS) 30.48 N45°45'10"W ON
IP(OU)
0.06SE
BENT
SIDE YARD (OTHER SIDE) 1.5 m 1.55 m
0.03NW
FENCE
0.22NE
IP(OU) B
REAR YARD 9.0 m 24.25 m
283.38
28
POST&WIRE FENCE
1.6
DIA0.3
BUILDING HEIGHT 10.5 m 10.4 m
283.00
282.00
CLIENT
0.39NE
0.35SE
FENCE
4
28
LANDSCAPE AREA 40.00 % 64%

0.9
0.22NE
FENCE
28
1.9
0
X
1
X
HARVINDER D.
28
DIA0.3
2.3
PROPOSED DWELLING 316.80 m²
0.19SE
FENCE
3
RESIDENCE
28
GARAGE 99.96 m²
28
2.5
28
3.2
PORCHES 17.18 m²
28
1.7
N44°50'10"E
2
3.0
DECK 38.55 m²
(D1&MEAS)
7
CO
28
2
1.7
0 ARCHITECT
PROPOSED MAX 0.70m
PROPOSED SILT FENCE

KHALSA DESIGN INC.
27
28
NC
1.5
AS PER OPSD 219.110

RETAINING WALL
PROPOSED SILT FENCE
28
8
283.45
2.4
AS PER OPSD 219.110
TOTAL 472.49 m²
RAIL FENCE
ES
BOTTOM OF SLOPE
PO TO
SIO
79'-6 282.85
[24.25m]
F SL
28
282.60
282.70
1.4
1/2"
283.00
O PE
5
28
GRASS
3.3
N
28
X
7
X
2.8
X
X
28
282.30
X
TW:283.10
2.6
X
WE
283.10
283.00
28
0
28
X
282.4
3.1
1.8
283.25
5
6
2
43'-7 1/2"
ST
[13.29m]
ARMOR STONE
RETAINING WALL
32'-9 1/2"
[10.00m]
PROPOSED
DRIVEWAY
(N45°10'50"E D1)
4.2%
N45°10'15"E
5.3%
282
.63
2.0%
X
RETAINING WALL
BRAMPTON, ON
SUBJECT TO EASEMENT AS IN INST. No. RO1022294

24'-0" 18'-10 1/2"
TW:283.60
282.20
28
282.90 15R
[7.32m]
OF
[5.76m]
283.50
2.1
282.91
283.50
28
283.56
282.91
282.80
3.5 283.45
6 4.0%
28
28
TELEPHONE: 647-468-2940
28
3.0
8
1.9
2.8
DN
6R
DN
6R
UP
4
X
9
X
X
PE
PART 3, PLAN 43R-19369

PART 2, PLAN 43R-19369
X
SLO
X
CONSULTANTS:
FENCE
0.06NW
X
X
UP
CHAIN LINK FENCE

STRUCTURAL ENGINEER:
PIN 14258-0082 (LT)

COVERED DECK
282.40
4.0%
BELOW GRADE
PROPOSED
ENTRANCE
STRUCUTRAL SEAL:
FENCE
0.23SE
SWALE
GRASS
2.0%
63.79
(63.77 D1)
(63.87 P2)
GARAGE
REGION OF PEEL NOTES:
5
PIN 14258-0080 (LT)
ALL MATERIALS AND CONSTRUCTION METHODS MUST CORRESPOND TO THE CURRENT PEEL PUBLIC WORKS
3.2%
STANDARDS AND SPECIFICATIONS

HU
282.60
283.8
0 WATERMAIN AND/OR WATER SERVICE MATERIALS 100 mm (4") AND LARGER MUST BE P.V.C. CLASS 150 TO AWWA
(P1&MEAS)
FR. 6.50 SPEC C900-75 AND COPPER TYPE 'K' FOR 50 DIA. AND SMALLER
4.0%
R
28
BORAD 283.65 WATERMAINS AND/OR WATER SERVICES ARE TO HAVE A MINIMUM COVER OF 1.7 m (5'6") WITH A MINIMUM
283.
GRASS
3.7
FENCE HORIZONTAL SPACING OF 1.2 m (4') FROM THEMSELVES AND ALL OTHER UTILITIES
28
ON
75
[21.67m]
2.4
PROVISIONS FOR FLUSHING WATER LINE PRIOR TO TESTING, ETC. MUST BE PROVIDED WITH AT LEAST A 50 mm (2")
71'-1"
7
OUTLET ON A 100 mm (4") AND LARGER LINES. COPPER LINES ARE TO HAVE FLUSHING POINTS AT THE END, THE
X
SAME SIZE AS THE LINE. THEY MUST ALSO BE HOSED OR PIPED TO ALLOW THE WATER TO DRAIN ONTO A PARKING
PROPOSED 2 STOREY
X
PROPOSED
DRIVEWAY
LOT OR DOWN A DRAIN. ON FIRE LINES, FLUSHING OUTLET TO BE 100 mm (4") DIAMETER MINIMUM ON A HYDRANT
28
TA
3.6
ALL CURB STOPS TO BE 3.0 m (10') OFF THE FACE OF THE BUILDING UNLESS OTHERWISE NOTED
SINGLE FAMILY DWELLING
9
282.80
FURNACE
0.12SE
FENCE
283.957R
COVERED
HYDRANT AND VALVE SET TO REGION STANDARD 1-6-1 DIMENSION A AND B, 0.7 m (2') AND 0.9 m (3') AND TO
RIO
PORCH
HAVE PUMPER NOZZLE

FFE = 285.47
4.0%
UP
UP
2.0%
WATERMAINS TO BE INSTALLED TO GRADES AS SHOWN ON APPROVED SITE PLAN. COPY OF GRADE SHEET MUST
GFE = 283.40 FR. 6.42 BE SUPPLIED TO INSPECTOR PRIOR TO COMMENCEMENT OF WORK, WHERE REQUESTED BY INSPECTOR
WATERMAINS MUST HAVE A MINIMUM CLEARANCE OF 0.3 m (12") OVER / 0.5 m (20") UNDER SEWERS AND ALL
28
BFE = 282.06 OTHER UTILITIES WHEN CROSSING

3.8
DIA0.4
X
AT THE PROPERTY LINE

MATCH EXISTING

9
ALL PROPOSED WATER PIPING MUST BE ISOLATED FROM EXISTING LINES IN ORDER TO ALLOW INDEPENDENT
2.0%
ST
PRESSURE TESTING AND CHLORINATING FROM EXISTING SYSTEMS THESE DRAWINGS ARE NOW AND DO
283.00
28

3.8
ALL LIVE TAPPING AND OPERATION OF REGION WATER VALVES SHALL BE ARRANGED THROUGH THE REGIONAL
8
INSPECTOR ASSIGNED OR BY CONTACTING THE OPERATIONS AND MAINTENANCE DIVISION DESIGN USE OF THESE PLANS OR ANY
4.0%
RE
.34
AT THE PROPERTY LINE
MATCH EXISTING ELEVATION
28
283.85
283 FORM OF REPRODUCTION OF THIS DESIGN

2.9
(119.40 P1)
LOCATION OF ALL EXISTING UTILITIES IN THE FIELD TO BE ESTABLISHED BY THE CONTRACTOR.

119.27 ELEVATION

3
4'-11" 75'-0" 20'-9" THE CONTRACTOR(S) SHALL BE SOLELY RESPONSIBLE FOR LOCATES, EXPOSING, SUPPORTING AND PROTECTING WRITTEN CONSENT IS PROHIBITED AND
ET
OF ALL UNDERGROUND AND OVERHEAD UTILITIES AND STRUCTURES EXISTING AT THE TIME OF CONSTRUCTION IN
28
[1.50m] [22.86m] [6.33m] SHALL RESULT IN THE FULLEST EXTENT OF

X
THE AREA OF HIS WORK. WHETHER SHOWN ON THE PLANS OR NOT, AND FOR ALL REPAIRS AND CONSEQUENCES
3.9
X
FENCE
0.52SE
283.95
X 84
X
(P2&MEAS)
EXISTING PROSECUTION UNDER LAW

2
284.20
284.25
RESULTING FROM DAMAGE TO SAME.
28
7
284.
28
X
4.1 284.
28 26 84.28
283.80
3.9
DWELLING TO BE 02
.16.24
284.29 6
28
284.309
THE CONTRACTOR(S) SHALL BE SOLELY RESPONSIBLE TO GIVE 72 HOURS WRITTEN NOTICE TO UTILITIES PRIOR TO
05
1
283.20
4.
REMOVED
28
COVERED CROSSING SUCH UTILITIES, FOR THE PURPOSE OF INSPECTION BY THE CONCERNED UTILITY. THIS INSPECTION WILL
284.28 ARCHITECT SEAL:
4.5
BE FOR THE DURATION OF THE CONSTRUCTION, WITH THE CONTRACTOR RESPONSIBLE FOR ALL COSTS ARISING
PORCH
4.0% 28
28
28
DRILLED WELL
PROPOSED
FROM SUCH INSPECTION.

DIA0.25
2
4.1
DIA0.3
284.32
EXISTING SEPTIC TO BE
4.0
28
X
4
4.6
2.0%
7
284.20
284.30
DECOMMISSIONED
28
1
284.
3.5
[1.50m]
3.8
AND REMOVED
TANK
SEPTIC
DIA0.25
4'-11"
X
5
284.25
7
DIA0.5
03
BUSH
GRADING & DRAINAGE NOTES

2.0%
28
X
(63.48 D1)
3.9
NEW PROPOSED 05 - 02 - 2024

63.40
1. MINIMUM GRADIENT OF GRASS SWALES ALONG SIDE AND REAR LOT LINES SHALL BE 2.0%. THE PROPOSED
28
28
ELEVATION OF THE SIDE YARD SHALL BE A MINIMUM OF 0.15m BELOW THE FINISHED GRADE AT THE BUILDING
4.1
4.1
DRILLED WELL
283.40
OF LOT 27, CON. 5, W.H.S.

28
18'-1 LINE. THE MAXIMUM SWALE GRADIENT SHALL BE 5.0%.

3
MOST NORTHERLY CORNER

416.20
1/2"
4.0
[4.50m]
284.10
[5.52
28
0.20SE
FENCE
14'-9"
m]
X
4
2. TAKE UP REAR YARD GRADE DIFFERENCE USING SLOPES BETWEEN 2.0% AND 5.0% FOR A MAXIMUM OF 75%
3.7
X
19.61
19.36
284.09
OF THE REAR YARD AND SLOPES OF 3 HORIZONTAL AND 1 VERTICAL MAXIMUM TO THE REAR LOT LINE.
3
3. EDGE OF THE DRIVEWAYS ARE A MINIMUM OF 1.0m FROM EDGE OF STREET CATCH BASIN AND STREET
[17.22m]
FURNITURE. THE BUILDER IS TO VERIFY THE LOCATION AND TO INFORM THE ENGINEER IF THE DIMENSION
56'-6"
283.80
CANNOT BE MAINTAINED PRIOR TO EXCAVATION FOR THE FOOTINGS.

284.00
DIA0.15
RAIL FENCE
28
ASPHALT
Project number 24003
PROPOSED
DRIVEWAY
4. BRICK LINE SHALL BE 0.15m ABOVE SOD ELEVATION.

4.0
KING ST
[2.44m]
[6.00m]
DIA0.25
GRASS
DRIVEWAY
19'-8"
8'-0"
PROPOSED ASPHALT
DRIVEWAY
05/02/2024
284.10
Date
2.0%
X
5. ALL NEW FENCES REQUIRED ABUTTING PUBLIC LANDS AND OR EXISTING PROPERTIES SHALL BE
28
X
CONSTRUCTED WITH MATERIAL INCLUDING FOUNDATIONS COMPLETELY ON PRIVATE LANDS AND TOTALLY
4.2
Drawn by ASB
X
EXISTING CLEAR OF ANY 0.3m RESERVES.

4
ENTRANCE TO Checked by KDI

28
6. SOIL CONSULTANTS VERIFICATION REQUIRED FOR FOOTINGS CONSTRUCTED ON ENGINEERED FILL LOTS.
3.3
REMAIN Scale As indicated

283.90
LEANING SE
HELD BASE
9
7. THE BUILDER MUST VERIFY THE AS CONSTRUCTED ON SANITARY AND STORM SERVICES INVERTS AND INFORM
[4.50m]
THE ENGINEER IF THE MINIMUM 2.0% GRADE CANNOT BE MAINTAINED PRIOR TO PLACING OF CONCRETE
14'-9"
REVISIONS
DRIVEWAY
FOOTING.
SIB(1028)
HELD BASE
LEANING
0.33SE
FENCE
SIB(1028)
DIA0.5
X
IB(OU)
8. BUILDER TO VERIFY LOCATION ALL HYDRANTS, STREET LIGHTS, TRANSFORMERS AND OTHER SERVICES. IF No. Description Date
0.10SW
0.04NW
FENCE
DIA0.5
28
MINIMUM DIMENSIONS ARE NOT MAINTAINED BUILDER IS TO RELOCATE AT HIS OWN EXPENSE.
R
4.2
284.30
284.30
DIA0.2
28
0
28
9. BUILDER TO STAKE OUT DRIVEWAY CURB DEPRESSION AT TIME OF TOP CURB INSTALLATION.
3.8
4'-6 1/2"
[1.38m]
4.1
EET
284.1
A
283.96 3
2
RAIL FENCE 10. THE PROPOSED GRADING AND APPURTENANT DRAINAGE WORKS COMPLY WITH SOUND ENGINEERING
PRINCIPALS.
X
X
123.33 N44°58'30"W 30.83 (D1&MEAS) RAIL FENC N44°58'30"W

(D2&SET)
E
11. THE PROPOSED GRADING IS IN CONFORMITY WITH THE GRADING PLANS APPROVED FOR THIS LOT SPECIFIC
UT
IN INST. No. VS152913 AS No. 5-70 BY-LAW

(D1&MEAS) BY DEDICATED
3.05
AND WILL NOT ADVERSELY AFFECT ADJACENT LANDS.

284.
0.23NE
FENCE
0.09NE
FENCE
FENCE
0.47NE
PART 48
26
PART 47A PART 47 12. THE PROPOSED BUILDING IS COMPATIBLE WITH THE PROPOSED GRADING.
HP 284.20 13. THE BUILDER IS RESPONSIBLE FOR RELOCATION OF ALL UTILITIES ON THE SITE, WHICH ARE NOT 1.0 METERS
TOP OF SL 155.65 (D2&SET) N44°58'30"W
TOP OF SLOPE OPE CLEAR FROM EDGE OF DRIVEWAY, INCLUDING STREET CATCH BASIN.
28
28
28
28
28
28
4.2
28
14. APPROVED PERMIT DRAWINGS AND CONSTRUCTION NOTES MUST BE REVIEWED AND FOLLOWED IN
4.2
4.2
4.0
3.9
3.9
4.2
3
CONJUNCTION WITH THE SITING AND GRADING PLAN. BUILDER TO VERIFY BUILDING ENVELOPE ON SITE PLAN
4
3
3
6
1
BOTTOM OF SLOPE MATCHES APPROVED PERMIT DRAWINGS & CONSTRUCTION NOTES PRIOR TO POURING CONCRETE. IF THERE
28
28
BOTTOM OF SLOP
E 283.11 ARE ANY DISCREPANCIES, THEY ARE TO BE BROUGHT TO THE ATTENTION OF KHALSA DESIGN INC.
28
28
28
28
3.9
3.7
3.5
3.7
3.8
3.3
28
1
5
28
1
15. UNLESS NOTED ON BUILDING ENVELOPE OR APPROVED PERMIT DRAWINGS AND CONSTRUCTION NOTES,
4
TOP OF SLOPE
4.2
5
4.1
TOP OF SLOPE ALL TOP OF FOUNDATION WALLS, INCLUDING GARAGE WALLS ARE TO BE CONSISTENT WITH THE ELEVATION
2
28
28
PROVIDED FOR THE TFW ON SITING AND GRADING PLAN. THE EXTERIOR OF THE FOUNDATION WALL TO BE
8
28
28
28
4.
28
4.3
13
PROVIDED WITH A REDUCTION IN THICKNESS FOR MASONRY VENEER AS REQUIRED.
4.1
3.8
4.0
4.2
28
1
8
9
TO REMAIN
EXISTING DRIVEWAY ENTRANCE
3
4.2
THE BUILDER / APPLICANT AGREES THAT BY REQUESTING THIS LOT GRADING CERTIFICATION BEFORE THE
5
28
AVAILABILITY OF INVERT CONNECTION, THE BUILDER / APPLICANT ASSUMES ALL RESPONSIBILITIES, OR ANY
28
TOP=283.92
CULVERT DIA0.45
28
TO REMAIN
EXISTING 0.45m∅ CULVERT
EDGE OF ASPHALT
SITE PLAN
28
4.0
4.1
POTENTIAL COMPLICATIONS DUE TO THE ULTIMATE SEWER CONNECTION ELEVATIONS AT THE STREET LINE.
4.2
4.3
28
7
8
28
6
4.4
4
4.4
0
5
ASP-1
CENTRELINE OF ASPHALT
28
28
28
28
4.2
28
4.3
4.4
4.5
3
4.5
4
4
1
PIN 14258-0104 (LT)

9

ON
STUCCO WALL CONSTRUCTION ROOF CONSTRUCTION (9.19., 9.23.13., 9.23.15.) WALL STUDS ABBREIVATIONS
WT1 WT6
STUCCO FINISH CONFORMING TO O.B.C. SECTION 9.28. AND APPLIED PER
RT1
No. 210 (10.25 kg/m2) ASPHALT SHINGLES, 3/8" (9.5) PLYWOOD SHEATHING WITH - REFER TO THIS CHART FOR STUD SIZE & SPACING AS REQUIRED FOR EXTERIOR AFF ABOVE FINISHED FLOOR JST JOIST
PROJECT NAME
MANUFACTURERS SPECIFICATIONS OVER 1 1/2" (38) E.I.F.S. (MINIMUM) ON "H" CLIPS. APPROVED WOOD TRUSSES @ 24" (610) O.C. MAX. APPROVED EAVES WALLS ONLY. REFER TO SITING & GRADING PLAN OF THIS UNIT FOR CONFIRMATION
APPROVED DRAINAGE MAT ON 1/2" (12.7) DENSGLASS GOLD GYPSUM BOARD PROTECTION TO EXTEND 2'-11" (890) FROM EDGE OF ROOF AND MIN. 12" (305) OF TOP OF FOUNDATION WALL AND ADDITIONAL INFORMATION. BBFM BEAM BY FLOOR MANUFACTURER LIN LINEN CLOSET
ON 2"x6" (38x140) SPRUCE STUDS @ 16" (406) O.C., INSULATION, APPROVED 6 BEYOND INNER FACE OF EXTERIOR WALL, 2"x4"(38x89) TRUSS BRACING @ 6'-0" - IF STUD WALL HEIGHT EXCEEDS MAX. UNSUPPORTED HEIGHT, WALL NEEDS TO BE BG FIXED GLASS W/ BLACK BACKING LVL LAMINATED VENEER LUMBER
MIL. POLYETHYLENE VAPOUR BARRIER, 1/2" (12.7) GYPSUM WALLBOARD INT. (1830) O.C. AT BOTTOM CHORD. PREFIN. ALUM. EAVESTROUGH, FASCIA, RWL & REVIEWED AND APPROVED BY ENGINEER.
FINISH. (REFER TO 35 NOTE AS REQUIRED)
STUCCO WALL CONSTRUCTION W/ CONTIN. INSULATION
VENTED SOFFIT. ATTIC VENTILATION 1:300 OF INSULATED CEILING AREA WITH
50% AT EAVES. EAVESTROUGH TO BE 4" MIN. WITH RWL CONNECTED TO STORM SIZE & SPACING OF STUDS: (OBC REFERENCE - TABLE 9.23.10.1.)
BM
BBRM
BEAM
BEAM BY ROOF MANUFACTURER
OTB/A
PL
OPEN TO BELOW/ABOVE
POINT LOAD
13948 Mississauga
WT6A SEWERS OR TO DISCHARGE ONTO CONCRETE SPLASH PADS AS PER MUNICIPAL SUPPORTED LOADS (EXTERIOR)
SIDING WALL CONSTRUCTION

STUCCO FINISH CONFORMING TO O.B.C. SECTION 9.28. AND APPLIED PER
MANUFACTURERS SPECIFICATIONS OVER 1 1/2" (38) E.I.F.S. (MINIMUM) ON
APPROVED DRAINAGE MAT ON APPROVED AIR/WATER BARRIER AS PER O.B.C.
REQUIREMENTS. TOWNHOUSES TO HAVE 5" (127) MIN. EAVESTROUGH WITH
ELEC. TRACED HEATER CABLE ALONG EAVESTROUGH AND DOWN RWL.
MIN.
STUD ROOF w/ OR ROOF w/ OR w/o ROOF w/ OR w/o ROOF w/ OR w/o
w/o ATTIC ATTIC & 1 FLOOR ATTIC & 2 FLOOR ATTIC & 3 FLOOR
CRF
C/W
CONVENTIONAL ROOF FRAMING PLT
COMPLETE WITH PT
PLATE
PRESSURE TREATED
Road, Caledon ON
WT2 SIZE,
SIDING MATERIAL AS PER ELEVATION ATTACHED TO FRAMING MEMBERS, 9.27.3.ON EXTERIOR TYPE RIGID INSULATION (JOINTS UNTAPED) in (mm) MAX. STUD SPACING, in (mm) O.C.
MECHANICALLY FASTENED AS PER MANUFACTURER'S SPECIFICATIONS, ON FOUNDATION WALL/FOOTINGS DJ/TJ DOUBLE JOIST/ TRIPLE JOIST PTD PAINTED
FURRING MEMBERS OR BLOCKING BETWEEN THE FRAMING MEMBERS ON
APPROVED SHEATHING PAPER ON 3/8" (9.5) EXT. GRADE SHEATHING ON 2"x6" 7/16" EXTERIOR TYPE SHEATHING ON 2"x6" (38x140) SPRUCE STUDS @ 16" (406)
WT5
POURED CONC. FOUNDATION WALL AS PER CHART BELOW ON CONTINUOUS
MAX. UNSUPPORTED HGT., ft-in (m)
DO DO OVER PWD POWDER ROOM
PROJECT ADDRESS
O.C., INSULATION, APPROVED 6 MIL. POLYETHYLENE VAPOUR BARRIER, 1/2" 2"x4" 24" (610) 16" (405) 12" (305) N/A
(38x140) STUDS @ 16" (406) O.C., INSULATION, APPROVED 6 MIL POLYETHYLENE KEYED CONCRETE FOOTING. THE OUTSIDE OF THE FOUNDATION SHALL BE
AIR/VAPOUR BARRIER, ON 1/2" (12.7) GYPSUM WALLBOARD INT. FIN. (GYPSUM (12.7) GYPSUM WALLBOARD INT. FINISH. (REFER TO 35 NOTE AS REQUIRED) DAMPROOFED FROM THE TOP OF THE FOOTING TO FINISHED GRADE AND (38x89) 9'-10" (3.0) 9'-10" (3.0) 9'-10" (3.0) N/A DRP DROPPED RT ROOF TRUSS
SHEATHING, RIGID INSULATION, AND FIBERBOARD SHALL NOT BE USED FOR STUCCO WALL @ GARAGE CONST. BRUSH COAT FROM THE TOP TO 2" BELOW GRADE. PROVIDE A DRAINAGE LAYER 2"x6" - 24" (610) 16" (406) 12" (305) E.I.F.S. EXTERIOR INSULATION FINISH SYSTEM RWL RAIN WATER LEADER
THE ATTACHMENT OF SIDING (9.23.16.3.(1.)) (REFER TO 35 NOTE AS REQ.) WT6B ON THE OUTSIDE OF THE FOUNDATION WALL. SEAL THE DRAINAGE LAYER AT (38x140) - 9'-10" (3.0) 11'-10" (3.6) 5'-11" (1.8) 13948 Mississauga Road, Caledon
NOTE: STUCCO FINISH CONFORMING TO O.B.C. SECTION 9.28. AND APPLIED PER THE TOP. THE TOP OF THE CONC. FOOTING SHALL BE DAMPROOFED. ENG ENGINEERED SB SOLID BEARING WOOD POST
SIDING WALL CONSTRUCTION W/ CONTIN. INSULATION MANUFACTURERS SPECIFICATIONS OVER 1 1/2" (38) E.F.I.S (MINIMUM) ON CONCRETE FOOTINGS SUPPORTING JOIST SPANS GREATER THAN 16'-1" (4900) GENERAL NOTES EST ESTIMATED SBFA SB FROM ABOVE
ON
3-DIMENSIONAL IMAGES ARE NOT TO BE WT2A
SIDING MATERIAL AS PER ELEVATION ATTACHED TO FURRING MEMBERS ON
APPROVED DRAINAGE MAT ON 1/2" (12.7) DENSGLASS GOLD GYPSUM BRD. ON
STUDS CONFORMING TO O.B.C (9.23.10.1.) & SECTION 1.1., 1/2" (12.7) GYPSUM
SHALL BE SIZED IN ACCORDANCE WITH 9.15.3.4 (1),(2) OF THE O.B.C. (REFER TO
APPROVED AIR/WATER BARRIER AS PER O.B.C. 9.27.3. ON EXTERIOR TYPE RIGID CHART BELOW FOR RESPECTIVE SIZE). BRACE FOUNDATION WALL PRIOR TO 2.1. WINDOWS FA FLAT ARCH SJ SINGLE JOIST
SCALED FROM AND USED FOR ANY MEANS OF INSULATION (JOINTS UNTAPED) MECHANICALLY FASTENED AS PER
WALLBOARD INT. FINISH. (REFER TO 35 NOTE AS REQ.)
*** FOR DWELLINGS USING CONTIN. INSULATION CONSTRUCTION,
BACKFILLING. ALL FOOTINGS SHALL REST ON NATURAL UNDISTURBED SOIL OF 1) EXCEPT WHERE A DOOR ON THE SAME FLOOR LEVEL AS THE BEDROOM PROVIDES FD FLOOR DRAIN SPR SPRUCE
MANUFACTURER'S SPECIFICATIONS ON3/8" (9.5) EXT. GRADE SHEATHING ON 2"x6" 75kPa OR COMPACTED ENGINEERED FILL WITH MIN. BEARING CAPACITY OF DIRECT ACCESS TO THE EXTERIOR, EVERY FLOOR LEVEL CONTAINING A BEDROOM IS
PROVIDE APPROVED DRAINAGE MAT ON 7/16" (11) EXTERIOR TYPE SHEATHING
MEASUREMENT FOR CONSTRUCTION. THE (38x140) STUDS @ 16" (406) O.C., INSULATION, APPROVED 6 MIL POLYETHYLENE OVER FURRING (AS REQ.) AND STUDS IN LIEU OF 1 1/2" (38) E.F.I.S (MINIMUM)
150kPa. IF SOIL BEARING DOES NOT MEET MINIMUM CAPACITY, ENGINEERED
FOOTINGS ARE REQUIRED. ACTUAL SOIL BEARING CAPACITY TO BE VERIFIED
TO HAVE AT LEAST ONE OUTSIDE WINDOW W/ MIN. 0.35m2 UNOBSTRUCTED OPEN FG FIXED GLASS STL STEEL
CLIENT
AIR/VAPOUR BARRIER, ON 1/2" (12.7) GYPSUM WALLBOARD INT. FIN. (GYPSUM ON APPROVED DRAINAGE MAT ON 1/2" (12.7) DENSGLASS GOLD GYPSUM BRD. PORTION W/ NO DIMENSION LESS THAN 1'-3" (380), CAPABLE OF MAINTAINING THE FL FLUSH T/O TOP OF
IMAGES ARE USED FOR GENERAL SHEATHING, RIGID INSULATION, AND FIBERBOARD SHALL NOT BE USED FOR THE WITH SOIL ENGINEERING REPORT.
REFER TO CONSTRUCTION DRAWINGS AND DETAILS FOR FOUNDATION
OPENING WITHOUT THE NEED FOR ADDITIONAL SUPPORT, CONFORMING TO 9.9.10.
ATTACHMENT OF SIDING (9.23.16.3.(1.)) (REFER TO 35 NOTE AS REQ.) 2) WINDOW GUARDS: A GUARD OR A WINDOW WITH A MAXIMUM RESTRICTED FLR FLOOR TYP TYPICAL
VISUALIZATION SIDING WALL @ GARAGE CONSTRUCTION P4
INTERIOR STUD PARTITIONS (9.23.9.8. , 9.23.10) WALL STRENGTH AND THICKNESS AND 9.15.4. OPENING WIDTH OF 4" (100) IS REQUIRED WHERE THE TOP OF THE WINDOW SILL IS GT GIRDER TRUSS U/S UNDERSIDE
WT2B BEARING PARTITIONS SHALL BE A MINIMUM 2"x4" (38x89) @ 16" (406) O.C. FOR 2 FOUNDATION WALLS SHALL NOT EXCEED 9'-10" (3.0m) IN UNSUPPORTED LOCATED LESS THAN 1'-7" (480) ABOVE FIN. FLOOR AND THE DISTANCE FROM THE
SIDING MATERIAL AS PER ELEVATION ATTACHED TO FRAMING MEMBERS,
FURRING MEMBERS OR BLOCKING BETWEEN THE FRAMING MEMBERS ON
APPROVED SHEATHING PAPER ON 3/8" (9.5) EXTERIOR TYPE SHEATHING ON
STOREY AND 12" (305) O.C. FOR 3 STOREY, NON-BEARING PARTITIONS 2"x4" (38x89)
@ 24" (610) O.C. PROVIDE 2"x4" (38x89) BOTTOM PLATE AND 2-2"x4" (2-38x89) TOP
HEIGHT UNLESS OTHERWISE NOTED. [9.15.4.2.(1.)]
UNREINFORCED SOLID CONCRETE FOUNDATION WALLS (9.15.4.2.)
FINISHED FLOOR TO THE ADJACENT GRADE IS GREATER THAN 5'-11" (1800). (9.8.8.1.)
3) WINDOWS IN EXIT STAIRWAYS THAT EXTEND TO LESS THAN 2'-11" (900) [3'-6" (1070)
HB
HRV
HOSE BIB
HEAT RETURN VENTILATION UNIT WIC
WD WOOD
WALK IN CLOSET
HARVINDER D.
PLATE. 1/2" (12.7) INT. DRYWALL BOTH SIDES OF STUDS, PROVIDE 2"x6" (38x140) FOR ALL OTHER BUILDINGS] SHALL BE PROTECTED BY GUARDS IN ACCORDANCE
RESIDENCE
THICKNESS
20 MPa 15 MPa STRENGTH
STUDS CONFORMING TO O.B.C (9.23.10.1.) & SECTION 1.1.,1/2" (12.7) GYPSUM MAX. HEIGHT FROM FIN. SLAB TO GRADE HWT HOT WATER TANK WP WEATHER PROOF
STUDS WHERE NOTED. PROVIDE 2"x4" (38x89) @ 24" (610) O.C. LADDER FRAMING WITH NOTE #2 (ABOVE). OR THE WINDOW SHALL BE NON-OPERABLE AND DESIGNED
WALLBOARD INTERIOR FINISH. (GYPSUM SHEATHING, RIGID INSULATION AND WHERE WALLS INTERSECT PERPENDICULAR TO ONE ANOTHER. PROVIDE 2"x4" UNSUPPORTED SUPPORTED AT TOP TO WITHSTAND THE SPECIFIED LOADS FOR BALCONY GUARDS AS PROVIDED IN
FIBERBOARD SHALL NOT BE USED FOR THE ATTACHMENT OF SIDING (38x89) WOOD BLOCKING ON FLAT @ 3'-11" (1194) O.C. MAX. BETWEEN FLOOR AT TOP ≤2.5m >2.5m & ≤2.75m >2.75m & ≤3.0m 4.1.5.15 OR 9.8.8.2
(9.23.16.3.(1.)) (REFER TO 35 NOTE AS REQ.) JOISTS WHEN NON-LOADBEARING WALLS ARE PARALLEL TO FLOOR JOISTS. 8" 3'-11" (1.20m) 7'-0" (2.15m) 7'-0" (2.15m) 6'-10" (2.10m) SYMBOLS
BRICK VENEER WALL CONSTRUCTION EXT. LOFT WALL CONSTRUCTION - NO CLADDING
*
10" 4'-7" (1.40m) 7'-6" (2.30m) 8'-6" (2.60m) 8'-2" (2.50m)
4) REFER TO TITLE PAGE FOR MAX. U-VALUE REQUIREMENTS
ALL ELECTRICAL FACILITIES SHALL BE INSTALLED IN ACCORDANCE WITH SECTION 9.34.
WT3 P4A 2.2. CEILING HEIGHTS
3 1/2" (90) BRICK VENEER 1" (25) AIR SPACE, 7/8"x7"x0.03" (22x180x0.76) GALV. METAL 12" 4'-11" (1.50m) 7'-6" (2.30m) 8'-6" (2.60m) 9'-3" (2.85m)
TIES @ 16" (400) O.C. HORIZ. 24" (600) O.C. VERT. BONDING AND FASTENING FOR
3/8" (9.5) EXTERIOR TYPE SHEATHING, 2"x6" (38x140) STUDS @ 16" (406) O.C.
8" 3'-11" (1.20m) 7'-6" (2.30m) 7'-6" (2.30m) 7'-2" (2.20m)
THE CEILING HEIGHTS OF ROOMS AND SPACES SHALL CONFORM TO TABLE 9.5.3.1. CLASS 'B' VENT EXHAUST VENT ARCHITECT
TIES TO CONFORM WITH 9.20.9. ONAPPROVED SHEATHING PAPER, 3/8" (9.5)
INSULATION AND 6 mil POLYETHYLENE VAPOUR BARRIER WITH APPROVED
CONT. AIR BARRIER. 1/2" (12.7) GYPSUM WALLBOARD INT. FINISH. (9.23.) *
10" 4'-7" (1.40m) 7'-6" (2.30m) 8'-6" (2.60m) 9'-3" (2.85m) ROOM OR SPACE MINIMUM HEIGHTS DUPLEX OUTLET (HEIGHT AS
EXTERIOR TYPE SHEATHING, 2"x6" (38x140) STUDS @ 16" (406) O.C., INSULATION AND LIVING ROOM, DINING 7'-7" OVER 75% OF REQUIRED FLOOR AREA WITH A DUPLEX OUTLET (12" HIGH)
KHALSA DESIGN INC.
(2/3/4) 2"
12" 4'-11" (1.50m) 7'-6" (2.30m) 8'-6" (2.60m) 9'-3" (2.85m) NOTED A.F.F.)
4
6 mil POLYETHYLENE VAPOUR BARRIER WITH APPROVED CONTIN. AIR BARRIER. 1/2" EXT. LOFT WALL CONSTRUCTION - NO CLADDING ROOM AND KITCHEN CLEAR HEIGHT OF 6'-11" AT ANY POINT
(12.7) GYPSUM WALLBOARD INTERIOR FINISH. PROVIDE WEEP HOLES @ 32" (800) P4B 9" MIN. THICK FOUNDATION WALL IS REQUIRED FOR MASONRY VENEER
O.C. BOTTOM COURSE AND OVER OPENINGS. PROVIDE BASE FLASHING UP MIN. 6" W/ CONTINUOUS INSULATION *
FINISHED EXTERIOR WALLS WITH CONTINUOUS INSULATION CONDITION, TO BEDROOM 7'-7" OVER 50% OF REQUIRED FLOOR AREA OR 6'-11"
OVER ALL OF THE REQUIRED FLOOR AREA.
HEAVY DUTY OUTLET SWITCH (2/3/4 WAY)
(150) BEHIND BUILDING PAPER (9.20.13.6.) (REFER TO 35 NOTE AS REQUIRED) APPROVED AIR/WATER BARRIER AS PER O.B.C. 9.27.3. ON EXTERIOR TYPE RIGID PROVIDE MIN. BEARING FOR SILL PLATES, BEAMS AND FLOOR JOIST AS PER LIGHT FIXTURE (CEILING
INSULATION (JOINTS UNTAPED) MECHANICALLY FASTENED AS PER 9.23.7.2., 9.23.8.1., & 9.23.9.1. OF THE O.B.C
. 6'-11" OVER AT LEAST 75% OF THE BASEMENT AREA POT LIGHT
MANUFACTURER'S SPECIFICATIONS, ON 3/8" (9.5) EXTERIOR TYPE SHEATHING, BASEMENT EXCEPT THAT UNDER BEAMS AND DUCTS THE MOUNTED)
BRICK VENEER WALL CONSTRUCTION W/ CONTIN. INSULATION 2"x6" (38x140) STUDS @ 16" (406) O.C. INSULATION AND 6 mil POLYETHYLENE CLEARANCE IS PERMITTED TO BE REDUCED TO 6'-5".
WT3A MINIMUM STRIP FOOTING SIZES (9.15.3.) LIGHT FIXTURE (PULL CHAIN) LIGHT FIXTURE (WALL MOUNTED)
PC
3 1/2" (90) BRICK VENEER 1" (25) AIR SPACE, 7/8"x7"x0.03" (22x180x0.76)GALV. METAL VAPOUR BARRIER WITH APPROVED CONT. AIR BARRIER. 1/2" (12.7) GYPSUM BATHROOM, LAUNDRY 6'-11" IN ANY AREA WHERE A PERSON WOULD
TIES @ 16" (400) O.C. HORIZ. 24" (600) O.C. VERT. BONDING AND FASTENING FOR NUMBER FLOORS SUPPORTING INT. SUPPORTING SUPPORTING
WALLBOARD INT. FINISH. (9.23.) SUPPORTED LOAD BEARING EXTERIOR PARTYWALL AREA ABOVE GRADE NORMALLY BE STANDING
TIES TO CONFORM WITH 9.20.9. ON APPROVED AIR/WATER BARRIER AS PER O.B.C. MASONRY WALLS TV CABLE T.V. JACK TELEPHONE JACK
9.27.3. ON EXTERIOR TYPE RIGID INSULATION (JOINTS UNTAPED) MECHANICALLY 1 16" WIDE x 6" THICK 16" WIDE x 6" THICK16" WIDE x 6" THICK FINISHED ROOM NOT 6'-11"
T
1 HR. PARTY WALL (CONC. BLOCK) ([SB-3] WALL TYPE 'B6e' & 'B1b') MENTIONED ABOVE CHANDELIER (CEILING
FASTENED AS PER MANUFACTURER'S SPECIFICATIONS, ON 3/8" (9.5) EXTERIOR P5 2 24" WIDE x 8" THICK 20" WIDE x 6" THICK24" WIDE x 8" THICK CV CENTRAL VACUUM OUTLET
TYPE SHEATHING, 2"x6" (38x140) STUDS @ 16" (406) O.C., INSULATION AND 6 mil MEZZANINES 6'-11" ABOVE & BELOW FLOOR ASSEMBLY (9.5.3.2.) MOUNTED)
1/2" (12.7) GYPSUM SHEATHING ON EACH SIDE ON 2"x2" (38x38) VERTICAL WD. 3 36" WIDE x 14" THICK26" WIDE x 9" THICK36" WIDE x 14" THICK
POLYETHYLENE VAPOUR BARRIER WITH APPROVED CONTIN. AIR BARRIER. 1/2" STRAPPING @ 24" (610) O.C. ON 8" (200) CONC. BLOCK FILL STRAPPING STORAGE GARAGE 6'-7" (9.5.3.3.)
(12.7) GYPSUM WALLBOARD INTERIOR FINISH. PROVIDE WEEP HOLES @ 32" (800) CAVITY EACH SIDE WITH AT LEAST 90% OF ABSORPTIVE MATERIAL 2.3. MECHANICAL / PLUMBING
O.C. BOTTOM COURSE AND OVER OPENINGS. PROVIDE BASE FLASHING UP MIN. PROCESSED FROM ROCK, SLAG OR GLASS. TAPE, FILL & SAND ALL GYPSUM
6" (150)OVER RIGID INSULATION (9.20.13.6.) (REFER TO 35 NOTE AS REQUIRED) JOINTS. EXPOSED BLOCK MUST BE SEALED W/ 2 COATS OF PAINT OR 1) MECHANICAL VENTILATION IS REQUIRED TO PROVIDE 0.7 AIR CHANGE PER HOUR
IF NOT AIR CONDITIONED 1 PER HOUR IF AIR CONDITIONED AVERAGED OVER 24 SA SMOKE ALARM (9.10.19.)
FURRED WITH 2"x2" (38x38) WD. STRAPPING & 1/2" (12.7) GYPSUM SHEATHING. HOURS. WHEN A VENTILATION FAN (PRINCIPAL EXHAUST) IS REQUIRED, CONFORM PROVIDE ONE PER FLOOR, NEAR THE STAIRS CONNECTING THE FLOOR LEVEL. ALARMS
BRICK VENEER WALL @ GARAGE CONSTRUCTION
WT3B 1 HR. PARTY WALL (DOUBLE STUD) ([SB-3] WALL TYPE 'W13c') TO OBC 9.32.3.4. WHEN A HRV IS REQUIRED, CONFORM TO 9.32.3.11. REFER TO ARE TO BE INSTALLED IN EACH SLEEPING ROOM AND IN A LOCATION BETWEEN
3 1/2" (90) BRICK VENEER , MIN. 1" (25) AIR SPACE, 7/8"x7"x0.03" (22x180x0.76) GALV. P5A MECHANICAL DRAWINGS. SLEEPING ROOMS AND CONNECTING HALLWAYS AND WIRED TO BE INTERCONNECTED
METAL TIES @ 16" (400) O.C. HORIZ. 24" (600) O.C. VERT.BONDING AND FASTENING 5/8" (15.9) TYPE 'X' GYPSUM SHEATHING ON EXTERIOR SIDE OF 2 ROWS OF TO ACTIVATE ALL ALARMS IF ONE SOUNDS. ALARMS ARE TO BE CONNECTED TO AN
FOR TIES TO CONFORM WITH 9.20.9. ON APPROVED SHEATHING PAPER, 3/8" (9.5) 2"x4" (38x89) STUDS @ 16" (406) O.C., MIN. 1" (25) APART ON SEPARATE 2"x4" 2) REFER TO HOT WATER TANK MANUFACTURER SPECS. CONFORM TO OBC 9.31.6. ELECTRICAL CIRCUIT AND WITH A BATTERY BACKUP. ALARM SIGNAL SHALL MEET
EXTERIOR TYPE SHEATHING ON STUDS CONFORMING TO O.B.C (9.23.10.1.) & (38x89) SILL PLATES. FILL ONE SIDE OF STUD CAVITY WITH AT LEAST 90% 3) REFER TO TITLE PAGE FOR SPACE HEATING EQUIPMENT, HRV AND DOMESTIC TEMPORAL SOUND PATTERNS MIN. ALARMS SHALL HAVE A VISUAL SIGNALLING
SECTION 1.1., 1/2" (12.7) GYPSUM WALLBOARD INTERIOR FINISH, PROVIDE WEEP OF ABSORPTIVE MATERIAL PROCESSED FROM ROCK, SLAG OR GLASS. HOT WATER HEATER MINIMUM EFFICIENCIES. COMPONENT AS PER THE "NATIONAL FIRE ALARM AND SIGNALING CODE 72".
HOLES @ 32" (800) O.C. AT BOTTOM COURSE AND OVER OPENINGS, PROVIDE TAPE FILL AND SAND ALL GYPSUM JOINTS.
BASE FLASHING UP 6" (150) MIN. BEHIND BUILDING PAPER (9.20.13.6.) (REFER TO 4) DRAIN WATER HEAT RECOVERY UNIT(S) WILL BE INSTALLED CONFORMING TO THE
REQUIREMENTS OF 3.1.1.12. OF THE O.B.C. CMD CARBON MONOXIDE ALARM (9.33.4.)
35 NOTE AS REQ.) 2 HR. FIREWALL ([SB-3] WALL TYPE 'B6e' & 'B1b') ** CHECK LOCAL BY-LAWS FOR REQUIREMENTS ** A CARBON MONOXIDE ALARM(S)
P5B 2.4. LUMBER
1/2" (12.7) GYPSUM SHEATHING ON EACH SIDE ON 2"x2" (38x38) VERTICAL 1) ALL LUMBER SHALL BE SPRUCE No.2 GRADE OR BETTER, UNLESS NOTED OTHERWISE. CONFORMING TO CAN/CGA-6.19 SHALL BE INSTALLED ON OR NEAR THE CEILING IN EA.
WOOD STRAPPING @ 24" (610) O.C ON 8" (200) CONC. BLOCK 75% SOLID. DWELLING UNIT ADJACENT TO EACH SLEEPING AREA. CARBON MONOXIDE ALARM(S)
2) STUDS SHALL BE STUD GRADE SPRUCE, UNLESS NOTED OTHERWISE.
WALL TYPES
FILL STRAPPING CAVITY EACH SIDE WITH AT LEAST 90% OF ABSORPTIVE SHALL BE PERMANENTLY WIRED WITH NO DISCONNECT SWITCH, WITH AN ALARM THAT IS
MATERIAL PROCESSED FROM ROCK, SLAG OR GLASS. TAPE, FILL & SAND 3) LUMBER EXPOSED TO THE EXTERIOR TO BE SPRUCE No. 2 GRADE PRESSURE AUDIBLE WITHIN SLEEPING ROOMS WHEN THE INTERVENING DOORS ARE CLOSED.
ALL GYPSUM JOINTS. AT UNFINISHED AREAS, EXTERIOR FACE OF CONC. TREATED OR CEDAR, UNLESS NOTED OTHERWISE.
BLOCK TO BE SEALED WITH 2 COATS OF PAINT. GYPSUM SHEATHING TO 4) ALL LAMINATED VENEER LUMBER (LVL) BEAMS, GIRDER TRUSSES, AND METAL SB SOLID BEARING (BUILT-UP WOOD COLUMNS AND STUD POSTS)
BE ATTACHED TO CONC. BLOCK. (REFER TO DETAILS) HANGER CONNECTIONS SUPPORTING ROOF FRAMING TO BE DESIGNED & CERTIFIED THE WIDTH OF A WOOD COLUMN SHALL NOT BE LESS THAN THAN THE WIDTH OF
BY FLOOR AND ROOF TRUSS MANUFACTURER. SUPPORTED MEMBER. BUILT-UP WOOD COLUMNS SHALL BE NAILED TOGETHER WITH
5) JOIST HANGERS: PROVIDE APPROVED METAL HANGERS FOR ALL JOISTS AND NOT LESS THAN 3" (76) NAILS SPACED NOT MORE THAN 11 3/4" (300) O.C. THE NUMBER BRAMPTON, ON
BUILT-UP WOOD MEMBERS INTERSECTING WITH FLUSH BUILT-UP WOOD MEMBERS. OF STUDS IN A WALL DIRECTLY BELOW A GIRDER TRUSS OR ROOF BEAM SHALL
6) WOOD FRAMING NOT TREATED WITH A WOOD PRESERVATIVE, IN CONTACT WITH CONFORM TO TABLES A-34 TO A-37. (9.17.4., 9.23.10.7.)
CONCRETE, SHALL BE SEPARATED FROM THE CONC. BY AT LEAST 2 mil POLYETHYLENE
FILM, No.50 (45lbs) ROLL ROOFING OR OTHER DAMPPROOFING MATERIAL, EXCEPT TWO STOREY VOLUME SPACE. SEE CONSTRUCTION NOTE K39. TELEPHONE: 647-468-2940
WHERE THE WOOD MEMBER IS AT LEAST 6" (152) ABOVE THE GROUND.
2.5. STEEL (9.23.4.3.)
1) STRUCTURAL STEEL SHALL CONFORM TO CAN/CSA-G40-21 GRADE 300W. HOLLOW
STRUCT. SECTIONS SHALL CONFORM TO CAN/CSA-G40-21 GRADE 350W CLASS "H".
NON-ADJUSTABLE STEEL BASEMENT COLUMN EXPOSED BUILDING FACE w/ LIMITING DISTANCE <= 3'-11" (1.20m) CONSULTANTS:
ICE AND WATER SHIELD K15A K35 2) REINFORCING STEEL SHALL CONFORM TO CSA-G30-18M GRADE 400R.
K1A 4"x4"x3/8" SQUARE HSS NON-ADJUSTABLE STEEL COLUMN WITH 6"x6"x3/8" WALL ASSEMBLY CONTAINS INSULATION CONFORMING TO CAN/ULC-S702 &
PROVIDE ICE AND WATER SHIELD IN THE AREAS INDICATED. THE ICE AND WATER (152x152x9.5) STEEL PLATE TOP & BOTTOM. FIELD WELD BASEMENT COLUMN HAVING A MASS OF NOT LESS THAN 1.22 kg/m2 OF WALL SURFACE AND 1/2"
SHIELD SHALL BE A SELF ADHERING AND SELF SEALING MEMBRANE. SIDE LAPS CONNECTION. POURED CONCRETE FOOTING ON NATURAL UNDISTURBED SOIL (12.7) TYPE X GYPSUM WALLBOARD INTERIOR FINISH. EXTERIOR CLADDING
MUST BE NON-COMBUSTIBLE. WALL ASSEMBLY REQUIRES TO HAVE A FIRE
2.6. FLAT ARCHES STRUCTURAL ENGINEER:
MUST BE A MINIMUM 3 1/2" (90) AND END LAPS A MINIMUM 6" (152). AND TO OF 75kPa OR COMPACTED ENGINEERED FILL WITH MIN. BEARING CAPACITY OF 1) FOR 8'-0" (2440) CEILINGS, FLAT ARCHES SHALL BE 6'-10" (2080) A.F.F.
EXTEND UP DORMER WALLS A MINIMUM 12" (305). 150kPa AS PER SOILS REPORT. RESISTANCE RATING OF NOT LESS THAN 45 MINUTES & CONFORMING TO
O.B.C. (9.10.14. OR 9.10.15.). REFER TO DETAILS FOR TYPE & SPECS.
2) FOR 9'-0" (2740) CEILINGS, FLAT ARCHES SHALL BE 7'-10" (2400) A.F.F. MEM ENGINEERING INC.
PROFILED ROOF TRUSSES SUPPORTING 2 STOREY FLR. LOAD PROVIDE 42"x42"x18" (1070x1070x460) CONC. FOOTING 3) FOR 10'-0" (3040) CEILINGS, FLAT ARCHES SHALL BE 8'-6" (2600) A.F.F.
K1B ** AN OPENING IN AN EXPOSING BUILDING FACE NOT MORE THAN 20 in²
ROOF TRUSSES SHALL BE PROFILED AND/OR STEPPED AT RAISED COFFER/TRAY SUPPORTING 3 STOREY FLR. LOAD PROVIDE 48"x48"x24" (1220x1220x610) CONC. FOOTING (130cm²)SHALL NOT BE CONSIDERED AN UNPROTECTED OPENING AS PER 9.10.14.6.2.7. ROOF OVERHANGS
CEILINGS. ANGLED TRAY CEILINGS WILL BE SHEATHED W/ 3/8" (9.5) PLYWOOD.
NON-ADJUSTABLE STL. COLUMN AT FOUNDATION WALL COLD CELLAR PORCH SLAB (9.39.)
1) ALL ROOF OVERHANGS SHALL BE 1'-0" (305). UNLESS NOTED OTHERWISE. CLIMATIC DATA STRUCUTRAL SEAL:
K15B K36 2.8. FLASHING (9.20.13., 9.26.4. & 9.27.3.)
4"x4"x3/8" SQUARE HSS NON-ADJUSTABLE STEEL COLUMN WITH 6"x6"x3/8" FOR MAX. 8'-2" (2500) PORCH DEPTH, 5" (127) 32 MPa (4640psi) CONC. SLAB 1) FLASHING MATERIALS & INSTALLATION SHALL CONFORM TO O.B.C. DESIGN SNOW LOAD (9.4.2.2.): 2.20 kPa
(152x152x9.5) STEEL TOP PLATE & 6"x4"x3/8" (152x100x9.5) BOTTOM PLATE. BASE w/ 5-8% AIR ENTRAINMENT. REINF. WITH 10M BARS @ 7 7/8" (200) O.C. EACH
K5A
FOUNDATION REDUCTION IN THICKNESS FOR MASONRY
WHERE THE TOP OF THE FOUNDATION WALL IS REDUCED IN THICKNESS TO
PLATE 4-1/2"x10"x1/2" (120x250x12.7) WITH 2- 1/2"Ø x 12" LONG x 2" HOOK ANCHORS DIRECTION, W/ 1 1/4" (32) CLEAR COVER FROM BOTTOM OF SLAB TO FIRST 2.9. GRADING WIND LOAD (q50) (SB-1.2.): 0.44 kPa
(2- 12.7Øx305x50). FIELD WELD COLUMN TO BASE PLATE & STEEL BM. LAYER OF BARS & SECOND LAYER OF BARS LAID DIRECTLY ON TOP OF LOWER 1) THE BUILDING SHALL BE LOCATED OR THE BUILDING SITE GRADED SO THE WATER
PERMIT THE INSTALLATION OF MASONRY EXTERIOR FACING, THE REDUCED LAYER IN OPPOSITE DIR. 24"x24" (610x610) 10M DOWELS @ 23 5/8" (600) O.C., WILL NOT ACCUMULATE AT OR NEAR THE BUILDING AND WILL NOT ADVERSELY
SECTION SHALL BE NOT LESS THAN 3 1/2" (90) THICK. THE BRICK VENEER SHALL ANCHORED IN PERIMETER FND. WALLS. SLOPE SLAB 1.0% FROM DOOR. AFFECT ADJACENT PROPERTIES. CONFORM TO 9.14.6.
BE TIED TO THE FOUNDATION WALL WITH CORROSION RESISTANT METAL TIES NON-ADJUSTABLE STL. COLUMN AT FOUNDATION WALL
K15C 2.10. ULC SPECIFIED ASSEMBLIES
@ 7 7/8" (200) VERTICAL AND 2'-11" (889) HORIZONTAL. FILL VOID WITH MORTAR PROJECT SPECIFIC, SEE PLANS
BETWEEN WALL AND BRICK VENEER (9.15.4.7(2)(3) & 9.20.9.4(3)) RANGE HOODS AND RANGE-TOP FANS ALL REQUIRED INDIVIDUAL COMPONENTS THAT FORM PART OF ' ANY ULC LISTED
K37
STEEL BEAM BEARING AT FOUNDATION WALL (9.23.8.1.) COOKING APPLIANCE EXHAUST FANS VENTED TO EXTERIOR MUST ASSEMBLY', SPECIFIED WITHIN THESE DRAWINGS, CANNOT BE ALTERED OR SUBSTITUTED
FOUNDATION REDUCTION IN THICKNESS FOR JOISTS K16 BEAM POCKET OR 8"x8" (200x200) POURED CONC. NIB WALLS, MIN. BEARING 3 1/2" (90).
K5B CONFORM TO OBC 9.32.3.9. & 9.32.3.10. FOR ANY OTHER MATERIAL/PRODUCT OR SPECIFIED MANUFACTURER THAT IS IDENTIFIED
WHERE THE TOP OF THE FOUNDATION WALL IS REDUCED IN THICKNESS TO MAINTAIN MIN. 1/2" AIR SPACE ON ALL SIDES FOR BEAM POCKET IN THAT S' PECIFIED ULC LISTING
'. THERE SHALL BE NO DEVIATIONS UNDER ANY
PERMIT THE INSTALLATION OF FLOOR JOISTS, THE REDUCED SECTION SHALL BE CONVENTIONAL ROOF FRAMING (9.23.13., 9.23.15.) CIRCUMSTANCES IN ANY ULC' LISTED ASSEMBLY ' IDENTIFIED IN THESE DRAWINGS.
WOOD STRAPPING AT STEEL BEAMS (9.23.4.3.(3.), 9.23.9.3.) K38
NOT MORE THAN 13 3/4" (350) HIGH & NOT LESS THAN 3 1/2" (90) THICK (9.15.4.7(1)) K17 2"x6" (38x140) RAFTERS @ 16" (406) O.C., 2"x8" (38x184) RIDGE BOARD.
STEEL BEAMS DROPPED UNLESS NOTED OTHER. PROVIDE MIN 1-1/2" BEARING END 2"x4" (38x89) COLLAR TIES AT MID-SPAN. CEILING JOISTS TO BE 2"x4" (38x89)
FOUNDATION WALL & FOOTINGS REBAR RESTAIN ALL JOISTS w/ 2"x2" BAILER BOTH SIDES OF STEEL BEAM. @ 16" (406) O.C. FOR MAX. 9'-3" (2819) SPAN & 2"x6" (38x140) @ 16" (406) LEGEND DOOR SCHEDULE
K5C AT FLUSH HILTI FASTEN 2"x2" BAILER TO FLANGE. JOISTS FRAMED INTO THE SIDES OF STEELS O.C. FOR MAX. SPAN 14'-7" (4450). RAFTERS FOR BUILT UP ROOF OVER 3.1. WOOD LINTELS AND BUILT-UP WOOD CONFORMING TO SECTIONS 9.5.11, 9.6., 9.7.2.1, & 9.10.13.10
FOUNDATION WALL W/ VERTICAL 15M @ 16" O.C. & 10M HORIZONTAL 16" O.C.
BEAMS MUST BE SUPPORTED BY BEAM FLANGES OR LEDGER STRIPS BOLTED TO BEAM PRE-ENGINEERED ROOF TRUSSES AND OR CONVENTIONAL FRAMING TO (DIVISION B PART 9. TABLES A8 TO A10 AND A12, A15 & A16)
FOOTINGS W/ 2-15M REFORC. BOTTOM & CONT. BE 2"x4" (38x89) @ 24" (610) O.C. UNLESS OTHERWISE SPECIFIED. 1 EXTERIOR 2'-8" x 6'-8" x 1-3/4" (815 x 2030 x 45) INSULATED MIN. R4 (RSI 0.7)
WEBS PROVIDE RUBBON STRIPS TO PREVENT MOVEMENT OF TOP FLANGE, PROVIDE EDGE FORMING PART OF SENTENCE 9.23.4.2.(3), 9.23.4.2.(4), 9.23.12.3.(1),(3), 9.23.13.8.(2), 9.37.3.1.(1) 1A EXTERIOR 2'-10" x 6'-8" x 1-3/4" (865 x 2030 x 45) INSULATED MIN. R4 (RSI 0.7)
WEEPING TILE (9.14.3.)
K6 4" (100) Ø PERFORATED CLAY OR PLASTIC PIPE @ 1% SLOPE TO DRAIN. 6" BLOCKING FOR JOIST TWIST, EDGE SUPPORT AND SUBLIFOOR AND 38x38x600 LONG 2"x8" SPRUCE #2 2"x10" SPRUCE #2 2"x12" SPRUCE #2 1B EXTERIOR 3'-0" x 6'-8" x 1-3/4" (915 x 2030 x 45) INSULATED MIN. R4 (RSI 0.7)
(152) CRUSHED STONE GRANULAR COVER W/ FILTER CLOTH LOCATED SPLICE FOR JOISTS 12MM/ 1/2" CLEAR OF EAM FLANGE FOR JOIST SHIRKAGE. TWO STOREY VOLUME SPACES (9.23.10.1., 9.23.11., 9.23.16.)
K39 L1 2/2"x8" (2/38x184) L3 2/2"x10" (2/38x235) L5 2/2"x12" (2/38x286) 1C EXTERIOR 2'-6" x 6'-8" x 1-3/4" (760 x 2030 x 45) INSULATED MIN. R4 (RSI 0.7)
BELOW LEVEL OF FLOOR SLAB, INSTALL AROUND PERIMETER FOOTING OF FOR TRUSS JOISTS THI AND JAGER TRUSS FLUSH W/ BEAM PROVIDE 2" BEARING FLATE
WALL ASSEMBLY WIND LOADS B1 3/2"x8" (3/38x184) B3 3/2"x10" (3/38x235) B5 3/2"x12" (3/38x286)
BUILDING INCLUDING GARAGE AND CONNECT TO CITY SERVICES ANCHORED TO TOP FLANGE OF BEAM W/ SIMPSON STRONG TIE COMPANY INC. JOIST 1D EXTERIOR 3'-0" x 6'-8" x 1-3/4" (815 x 2030 x 45) INS. MIN. R4 (RSI 0.7) (SEE
<= 0.5 kPA (q50) > 0.5 kPa (q50)
HANGERS AHCORED TO TOP PLATE EXTERIOR STUDS B2 4/2"x8" (4/38x184) B4 4/2"x10" (4/38x235) B6 4/2"x12" (4/38x286) HEX NOTE 20)
BASEMENT SLAB OR SLAB ON GRADE (9.16.4.3.) SPACING MAX HEIGHT SPACING MAX HEIGHT
K7 GARAGE SLAB (9.16., 9.35.) BRICK 2-2"x6" 12" (305) O.C.18'-4" (5588) 8" (200) O.C. 18'-4" (5588) B7 5/2"x8" (5/38x184) B8 5/2"x10" (5/38x235) B9 5/2"x12" (5/38x286)
3" (80) MIN. 25MPa (3600psi) CONC. SLAB ON 4" (100) COARSE GRANULAR FILL, K18 1E EXTERIOR 3'-0" x 8'-0" x 1-3/4" (915 x 2440 x 45) INSULATED MIN. R4 (RSI 0.7)
OR 20MPa (2900psi) CONC. WITH DAMPPROOFING BELOW SLAB. PROVIDE 1/2" 4" (100) 32MPa (4650psi) CONC. SLAB WITH 5-8% AIR ENTRAINMENT ON OPT. (2-38x140)
4" (100) COARSE GRANULAR FILL WITH COMPACTED SUB-BASE OR SIDING SPR.#2 16" (406) O.C.18'-4" (5588) 12" (305) O.C.18'-4" (5588) ENGINEERED LUMBER SCHEDULE 2.0E-3300 BY GLOBAL LVL OR EQUAL 1F EXTERIOR 2'-8" x 6'-8" x 1-3/4" (815 x 2030 x 45) 20 MIN. F.R.R. DOOR/FRAME WITH APP.
(12.7) IMPERVIOUS BOARD FOR BOND BREAK AT EDGE. (9.13.) WHERE A SELF CLOSING DEVICE.
BASEMENT SLAB IS WITHIN 24" (610) OF THE EXTERIOR GRADE PROVIDE RIGID COMPACTED NATIVE FILL. SLOPE TO FRONT @ 1% MIN. BRICK 2-2"x8" 12" (305) O.C.21'-0" (6400) 12" (305) O.C.21'-0" (6400) 1 3/4" x 9 1/2" LVL 1 3/4" x 11 7/8" LVL 1 3/4" x 14" LVL
INSUL. AROUND THE PERIMETER EXTENDING MIN. 24" (610) BELOW GRADE. FOR GARAGE TO HOUSE WALLS/CEILING (9.10.9.16.) (2-38x140) 1G EXTERIOR 2'-8" x 6'-8" x 1-3/4" (815 x 2030 x 45) INSULATED MIN. R4 (RSI 0.7)
K19 SIDING SPR.#2 16" (406) O.C.21'-0" (6400)16" (406) O.C.21'-0" (6400) LVL2 1-1 3/4"x9 1/2" LVL3 1-1 3/4"x11 7/8" LVL10 1-1 3/4"x14"
SLAB ON GRADE CONDITIONS RIGID INSULATION SHALL BE APPLIED TO THE 1/2" (12.7) GYPSUM BOARD ON WALL AND CEILING BETWEEN HOUSE AND GARAGE,
UNDERSIDE OF THE ENTIRE SLAB.([SB-12] 3.1.1.7.(5) & (6)) PLUS REQUIRED INSULATION IN WALLS AND SPRAY FOAM FOR CEILINGS. TAPE STUDS ARE TO BE CONTINUOUS, C/W 3/8" (9.5) THICK EXTERIOR PLYWOOD LVL4 2-1 3/4"x9 1/2" LVL6 2-1 3/4"x11 7/8" LVL11 2-1 3/4"x14" 2 INTERIOR 3'-0" x 6'-8" x 1-3/8" (914 x 2030 x 35) COPYRIGHT KDI © 2023
EXPOSED FLOOR TO EXTERIOR AND SEAL ALL JOINTS GAS TIGHT. SHEATHING. PROVIDE SOLID WOOD BLOCKING BETWEEN WOOD STUDS LVL5 3-1 3/4"x9 1/2" LVL7 3-1 3/4"x11 7/8" LVL12 3-1 3/4"x14" 2A INTERIOR 2'-8" x 6'-8" x 1-3/8" (815 x 2030 x 35) THESE DRAWINGS ARE NOW AND DO
K8 @ 4'-0" (1220) O.C. VERTICALLY.
PROVIDE SPRAY FOAM INSULATION BETWEEN CANT. JOIST AND INSTALL FIN. K19A
GARAGE TO HOUSE WALLS/CEILING W/ CONTIN. INSULATION
- FOR HORIZ. DISTANCES LESS THAN 9'-6" (2896) PROVIDE 2"x6" (38x140) STUDS @ LVL8 4-1 3/4"x9 1/2" LVL9 4-1 3/4"x11 7/8" LVL13 4-1 3/4"x14" 3 INTERIOR 2'-6" x 6'-8" x 1-3/8" (760 x 2030 x 35)
PROVIDE 8'-0" HIGH
SOFFIT OR CLADDING AS PER ELEVATION TO U/S OF EXPOSED CANT. JOIST. 1/2" (12.7) GYPSUM BOARD ON CEILING AND ON WALLS INSTALLED OVER EXTERIOR 16" (406) O.C. WITH CONTIN. 2-2"x6" (2-38x140) TOP PLATE + 1-2"x6" (1-38x140) 3A INTERIOR 2'-4" x 6'-8" x 1-3/8" (710 x 2030 x 35) INTERIOR DOORS DESIGN USE OF THESE PLANS OR ANY
TYPE RIGID INSULATION
(JOINTS UNTAPED)MECHANICALLY FASTENED AS PER BOTTOM PLATE & MIN. OF 3-2"x8" (3-38x184) CONT. HEADER AT GROUND FLOOR LVL14 1-1 3/4"x7 1/4" LVL15 2-1 3/4"x7 1/4" LVL16 3-1 3/4"x7 1/4"
K9
EXPOSED CEILING TO EXTERIOR w/ ATTIC MANUFACTURER'S SPECIFICATIONS ON 3/8" EXTERIOR GRADE SHEATHING ON CEILING LEVEL TOE-NAILED & GLUED AT TOP, BOTTOM PLATES & HEADERS. STEEL LINTELS SUPPORTING MASONRY VENEER 4 INTERIOR 2'-0" x 6'-8" x 1-3/8" (610 x 2030 x 35) FOR ALL 10' CEILING FORM OF REPRODUCTION OF THIS DESIGN
INSULATION, 6 mil POLYETHYLENE VAPOUR BARRIER, 1/2" (12.7) GYPSUM BOARD STUDS BETWEEN HOUSE AND GARAGE, PLUS REQUIRED INSULATION IN WALLS & CONDITIONS IN WHOLE OR IN PART WITHOUT EXPRESS
(DIVISION B PART 9. TABLE 9.20.5.2.B.) 4A INTERIOR 2'-2" x 6'-8" x 1-3/8" (660 x 2030 x 35)
INTERIOR FINISH OR APPROVED EQ. SPRAY FOAM FOR CEILINGS. TAPE AND SEAL ALL JOINTS GAS TIGHT. (9.10.9.16.) UNSUPPORTED FOUNDATION WALLS
K42 FORMING PART OF SENTENCE 9.20.5.2.(2) & 9.20.5.2.(3) WRITTEN CONSENT IS PROHIBITED AND
GARAGE DOOR TO HOUSE (9.10.9.16., 9.10.13.10., 9.10.13.15.) 5 INTERIOR 1'-6" x 6'-8" x 1-3/8" (460 x 2030 x 35)
ALL STAIRS/EXTERIOR STAIRS (9.8.1.2., 9.8.2., 9.8.4.) REINFORCING AT STAIRS AND SUNKEN FLOOR AREAS
K10 K20 CODE SIZE BRICK STONE SHALL RESULT IN THE FULLEST EXTENT OF
GAS-PROOF DOOR AND FRAME. DOOR EQUIPPED WITH SELF CLOSING 2-20M BARS IN TOP PORTION OF WALL (UP T0 8'-0" OPENING)
MAX. RISE MIN. RISE MAX. RUN MIN. RUN MAX. TREAD MIN. TREAD DEVICE AND WEATHER STRIPPING. 3-20M BARS IN TOP PORTION OF WALL (8'-0" T0 10'-0" OPENING) L7 3 1/2" x 3 1/2" x 1/4" (89 x 89 x 6.4) 8'-1" (2.47m) 7'-6" (2.30m) PROSECUTION UNDER LAW
PRIVATE 7 7/8" (200) 5" (125) 14" (355) 10" (255) 14" (355) 11" (280) 4-20M BARS IN TOP PORTION OF WALL (10'-0" T0 15'-0" OPENING)
- BARS STACKED VERTICALLY AT INTERIOR FACE OF WALL L8 4" x 3 1/2" x 1/4" (102 x 89 x 6.4) 8'-9" (2.66m) 8'-1" (2.48m)
PUBLIC 7" (180) 5" (125) NO LIMIT 11" (280) NO LIMIT 11" (280) EXTERIOR AND GARAGE STEPS
K21 REINFORCING AT BASEMENT WINDOWS L9 4 7/8" x 3 1/2" x 5/16" (127 x 89 x 7.9) 10'-10" (3.31m) 10'-1" (3.03m)
MIN. STAIR WIDTH CURVED STAIRS ALL STAIRS PRECAST CONC. STEP OR WOOD STEP WHERE NOT EXPOSED TO WEATHER.
MAX RISE 7 7/8" (200), MIN. TREAD 9 1/4" (235). FOR THE REQUIRED NUMBER 2-15M HORIZ. REINFORCING ON THE INSIDE AND OUTSIDE FACE OF THE L10 4 7/8" x 3 1/2" x 3/8" (127 x 89 x 11) 11'-5" (3.48m) 10'-7" (3.24m) ARCHITECT SEAL:
PRIVATE 2'-10" (860) MIN. RUN 5 7/8" (150) MAX. NOSING 1" (25) OF STEPS REFER TO SITING AND GRADING DRAWINGS. EXTERIOR CONCRETE FOUNDATION WALL BELOW THE WIN. SILL. EXTEND BARS 24" (610) BEYOND
PUBLIC 2'-11" (900) MIN. AVG. RUN 7 7/8" (200) STAIRS WITH MORE THAN 2 RISERS AND 2 TREADS SHALL BE PROVIDED WITH THE OPENING. 2-15M VERTICAL REINFORCING ON THE INSIDE AND OUTSIDE L11 5 7/8" x 3 1/2" x 3/8" (152 x 89 x 11) 12'-6" (3.82m) 11'-7" (3.54m)
FOUNDATION AS REQUIRED BY ARTICLE 9.8.9.2. OR SHALL BE CANTILEVERED FACE OF THE FOUNDATION WALL ON EACH SIDE OF THE WINDOW OPENING. L12 7 1/8" x 4" x 3/8" (178 x 102 x 11) 14'-1" (4.30m) 13'-1" (3.99m)
** HEIGHT OVER STAIRS (HEADROOM) IS MEASURED VERTICALLY ACROSS AS PER SUBSECTION 9.8.10. - BARS TO HAVE MIN. 2" (50) CONC. COVER
WIDTH OF STAIRS FROM A STRAIGHT LINE TO THE TREAD & LANDING NOSING - BARS TO EXTEND 2'-0" (610) BEYOND BOTH SIDES OF OPENING
TO LOWEST POINT ABOVE AND NOT LESS THAN 6'-5" (1950) FOR SINGLE DRYER EXHAUST
DWELLING UNIT & 6'-8 3/4" (2050) FOR EVERYTHING ELSE. (9.8.2.2.) K22 STUD WALL REINFORCEMENT
CAPPED DRYER EXHAUST VENTED TO EXT. CONFORMING TO PART 6, OBC 9.32. K43
REQUIRED LANDING IN GARAGE - O.B.C. 9.8.6.2.(3.) PROVIDE STUD WALL REINFORCEMENT IN MAIN BATHROOM
FOR AN EXTERIOR STAIR SERVING A GARAGE W/ MORE THAN 3 RISERS. ATTIC ACCESS (9.19.2.1.)
K23 CONFORMING TO O.B.C. (9.5.2.3.(1) AND 3.8.3.8.(3)) (REFER TO DETAILS)
GUARDS, HANDRAILS & STEPS AS PER CONSTRUCTION HEX NOTE K10 & K11. ATTIC ACCESS HATCH WITH MIN. AREA OF 0.32m2 AND NO DIM. LESS
THAN 21 1/2" (545) WITH WEATHER STRIPPING. HATCHWAYS TO THE ATTIC WINDOW WELLS 05 - 02 - 2024
K44
OR ROOF SPACE WILL BE FITTED WITH DOORS OR COVERS AND WILL BE WHERE A WINDOW OPENS INTO A WINDOW WELL, A CLEARANCE OF NOT
PRECAST CONCRETE STEPS AND CAST IN PLACE CONCRETE STAIRS INSULATED WITH MIN. R20 (RSI 3.52) ([SB-12] 3.1.1.8.(1)) LESS THAN 21 5/8" (550) SHALL BE PROVIDED IN FRONT OF THE WINDOW.
K10A
SAME NOTES AT HEX 10 APPLY BUT PROVIDE 10M REINF. BAR IN NOSING FIREPLACE CHIMNEYS (9.21.) EVERY WINDOW WELL SHALL BE DRAINED TO THE FOOTING LEVEL OR
K24 OTHER SUITABLE LOCATION WITH A 4" (100) WEEPING TILE C/W A FILTER
WITH 15M BARS AT 12" OC BOTTOM BOTH WAYS AND 15M 12"X12" BENT TOP OF FIREPLACE CHIMNEY SHALL BE 2'-11" (889) ABOVE THE HIGHEST POINT CLOTH WRAP AND FILLED WITH CRUSHED STONE. (9.9.10.1.(5), 9.14.6.3.)
DOWEL LAPS @ 12" OC AT CONCRETE FOUNDATION BASE AND AT WHICH IT COMES IN CONTACT WITH THE ROOF AND 2'-0" (610) ABOVE THE
ROOF SURFACE WITHIN A HORIZ. DISTANCE OF 10'-0" (3048) FROM THE CHIMNEY. SLOPED CEILING CONSTRUCTION ([SB-12] 2.1.1.7., 9.23.4.2.)
FOUNDATION AND LANDING HEAD OF STAIRS K45
LINEN CLOSET 2"x12" (38x286) ROOF JOISTS @ 16" (406) O.C. MAX. (UNLESS OTHERWISE
K25 NOTED) W/ 2"x2" (38x38) PURLINS @ 16" (406) O.C. PERPENDICULAR TO ROOF
PROVIDE 4 SHELVES MIN. 14" (356) DEEP. JOIST (PURLINS NOT REQ. W/ SPRAY FOAM), W/ INSULATION BETWEEN JOIST,
GUARDS/RAILINGS (9.8.7., 9.8.8.)
K11 6 mil POLYETHYLENE VAPOUR BARRIER, 1/2" (12.7) GYPSUM WALLBOARD INT.
GUARDS TO BE DESIGNED NOT TO FACILITATE CLIMBING AND PROVIDING K26
MECHANICAL VENTILATION (9.32.1.3.)
FINISH OR APPROVED EQ. INSULATION VALUE DIRECTLY ABOVE THE INNER Project number 24003
MAX. OPENING CONFORMING TO O.B.C. 9.8.8.5. & 9.8.8.6. AND BE ABLE TO MECHANICAL EXHAUST FAN, VENTED TO EXTERIOR, TO PROVIDE AT LEAST SURFACE OF EXTERIOR WALLS SHALL NOT BE LESS THAN R20 (3.52 RSI).
RESIST LOADS AS PER TABLE 9.8.8.2. ONE AIR CHANGE PER HOUR. SEE GENERAL NOTE 2.3.
FLAT ROOF/BALCONY CONSTRUCTION
Date 05/02/2024
GUARD HEIGHTS - O.B.C. 9.8.8. PARTY WALL BEARING (9.23.8) K46 Drawn by
INTERIOR GUARDS: 2'-11" (900) MIN. K27
12"x12"x5/8" (305x305x15.9) STEEL PLATE FOR STEEL BEAMS AND 12"x12"x1/2"
WATERPROOFING MEMBRANE FULLY ADHERED TO 5/8" (15.9) T&G EXTERIOR ASB
GRADE PLYWOOD SHEATHING ON 2"x2" (38x38) PURLINS ANGLED TOWARDS
EXTERIOR GUARDS: 2'-11" (900) MIN. (LESS THAN 5'-11" (1800) TO GRADE)
3'-6" (1070) MIN. (MORE THAN 5'-11" (1800) TO GRADE)
(305x305x12.7) STEEL PLATE FOR WOOD BEAMS BEARING (MIN. 3-1/2" (89)) ON SCUPPER @ 2% MINIMUM LAID PERPENDICULAR TO 2"x8" (38x184) FLOOR Checked by KDI
CONC. BLOCK PARTY WALL, ANCHORED WITH 2-3/4" (2-19) x 8" (200) LONG JOISTS @ 16" (406) O.C. (UNLESS OTHERWISE NOTED). BUILT UP CURB TO BE
GUARDS FOR EXIT STAIRS: 3'-0" (920) MIN. GALV. ANCHORS WITHIN SOLID BLOCK COURSE. LEVEL W/ NON-SHRINK GROUT. 4" (100) MIN. ABOVE FINISHED BALCONY FLOOR. CONTINUOUS 'L' TRIM DRIP Scale
GUARDS FOR LANDINGS @ EXIT STAIRS: 3'-6" (1070) MIN. REFER TO NOTE SOLID BEARING (SECTION 3.0) FOR WD. STUD PARTY WALL. EDGE TO BE PROVIDED ON OUTSIDE FACE OF CURB. SCUPPER DRAIN TO BE
GUARDS FOR FLOORS & RAMPS IN GARAGES (SERVICE STAIRS) LOCATED 24" (610) MIN. AWAY FROM HOUSE. PREFINISHED ALUMINUM OR
FLOOR OR RAMP W/O EXTERIOR WALLS THAT IS 23 5/8" (600) OR MORE ABOVE K28
WOOD FRAMING IN CONTACT TO CONCRETE
PANEL FOR UNDERSIDE OF SOFFIT (9.23.2.3). REMOVE CURB WHERE REQ. REVISIONS
ADJACENT SURFACE REQUIRES CONT. CURB MIN. 6" (150) HIGH, AND GUARD WOOD BEARING WALLS, THE UNDERSIDE OF BUILT-UP WOOD POSTS AND BALCONY CONDITION
MIN. 3'-6" (1070) HIGH. SILLS SHALL BE WRAPPED WITH 2 mil POLY. STRIP FOOTINGS SUPPORTING
THE FOUNDATION WALL SHALL BE WIDENED 6" (152) BELOW THE BEARING SEE FLAT ROOF/BALCONY CONSTRUCTION NOTE. INCLUDE 2"x4" (38x89) PT. No. Description Date
REQUIRED GUARDS DECKING W/ 1/4" (6.4) GAPS LAID FLAT PARALLEL TO JOISTS ON 2"x4" (38x89)
WALL AND/OR WOOD POST. (9.17.4.3.)
BETWEEN WALKING SURFACE & ADJACENT SURFACE WITH A DIFFERENCE IN PT. SLEEPERS @ 12" (305) O.C. LAID FLAT PERPENDICULAR TO JOISTS
ELEVATION MORE THAN 23 5/8" (600) OR ADJACENT SURFACE WITHIN 3'-11" (1200) BUILT-UP WOOD POST AND FOOTING (9.17.4.1., 9.15.3.7.) BALCONY OVER HEATED SPACE CONDITION
& WALKING SURFACE W/ A SLOPE MORE THAN 1 IN 12 SHALL BE PROTECTED K29 1
3-2"x6" (3-38x140) BUILT-UP WOOD POST (UNLESS OTHERWISE NOTED) ON SEE FLAT ROOF/BALCONY CONSTRUCTION NOTE FOR ASSEMBLY. REFER TO
WITH GUARDS PER CONSTRUCTION HEX NOTE 11. METAL BASE SHOE ANCHORED TO CONC. WITH 1/2" (12.7) Ø BOLT, 24"x24"x12" PLANS FOR FLOOR JOIST SIZE & REFER TO HEX NOTE 9A FOR INSULATION AND
HANDRAIL HEIGHTS - O.B.C. 9.8.7. - REQUIRED AS PER 9.8.7.1.(3) (610x610x305) CONC. FOOTING OR AS PROVIDED ON PLAN. REFER TO NOTE 28 INTERIOR FINISH
MIN. HEIGHT AT STAIRS OR RAMP: 2'-10" (865)
MAX. HEIGHT AT STAIRS OR RAMP: 3'-6" (1070) STEP FOOTINGS (9.15.3.9.) BARREL VAULT CONSTRUCTION
K30 K47
MAX. HEIGHT AT LANDING: 3'-6" (1070) MIN. HORIZ. STEP = 23 5/8" (600). MAX. VERT. STEP = 23 5/8" (600). CANTILEVERED 2"x4" (38x89) SPACERS LAID FLAT ON 2"x10" (38x235) SPR. #2
STAIRS OR RAMP MIN. 7'-3" (2200) WIDE: 2'-9" (865) MIN. HEIGHT CONC. PORCH SLAB (9.16.4.) ROOF JOIST NAILED TO BUILT-UP 3-3/4" (19) PLYWOOD HEADER PROFILED FOR
SILL PLATES K31 BARREL. SPRAY FOAM INSULATION BETWEEN JOISTS W/ GYPSUM BOARD.
K12 MIN. 4" (100) CONCRETE SLAB ON GRADE ON 4" (100) COARSE GRANULAR
2"x4" (38x89) SILL PLATE WITH 1/2" (12.7)Ø ANCHOR BOLTS 8" (200) LONG, FILL, REINFORCED WITH 6x6xW2.9xW2.9 MESH PLACED NEAR MID-DEPTH OF INTERIOR FIN. (REFER TO DETAILS)
EMBEDDED MIN. 4" (100) INTO CONC. @ 7'-10" (2388) O.C., CAULKING OR GASKET SLAB. CONC. STRENGTH 32MPa (4640psi) WITH 5-8% AIR ENTRAINMENT ON
BETWEEN PLATE AND TOP OF FOUNDATION WALL. USE NON-SHRINK GROUT TO COMPACTED SUB-GRADE. FIRE STOPS
LEVEL SILL PLATE WHEN REQUIRED (9.23.7.) K48 PROVIDE HORIZONTAL BLOCKING BETWEEN STUDS IN WALLS
BASEMENT INSULATION ([SB-12] 3.1.1.7.) CONC. PORCH SLAB (9.16.4.) EXCEEDING 9'-10" IN HEIGHT
K13 K31
PROVIDECONTINUOUSBLANKET INSULATION W/ BUILT IN 6 mil POLYETHYLENE MIN. 4" (100) CONCRETE SLAB ON GRADE ON 4" (100) COARSE GRANULAR
VAPOUR BARRIER. INSULATION TO EXTEND NO MORE THAN 8" (200) ABOVE FILL, REINFORCED WITH 6x6xW2.9xW2.9 MESH PLACED NEAR MID-DEPTH OF DUCTS FURRED IN
SLAB. CONC. STRENGTH 32MPa (4640psi) WITH 5-8% AIR ENTRAINMENT ON 49 2"x2" STRAPPING
FINISHED BASEMENT FLOOR. DAMPROOFED WITH BUILDING PAPER BETWEEN
THE FOUNDATION WALL AND INSULATION UP TO GRADE LEVEL. COMPACTED SUB-GRADE. R-12 BATT INSULATION
BEARING STUD PARTITION IN BASEMENT (9.15.3.6., 9.23.10.1.) FURNACE VENTING (9.32.) 1/2" GYPSUM BOARD TAPED SANDED AND SEALED.
K14 K32 FASCIA, FRIEZE AND SOFFITS
2"x4" (38x89) STUDS @ 16" (406) O.C., 2"x4" (38x89) SILL PLATE ON DAMPPROOFING DIRECT VENT FURNACE TERMINAL MIN. 3'-0" (915) FROM A GAS REGULATOR. K50
MATERIAL OR 2 mil POLYETHYLENE FILM, 1/2" (12.7) Ø ANCHOR BOLTS 8" (200) MIN. 12" (305) ABOVE FIN. GRADE, FROM ALL OPENINGS, EXHAUST AND 1"x6" OR 2"x6" PRE-FINISHED ALUMINUM FASCIA AND FRIEZE BOARD AS PER
LONG, EMBEDDED 4" (100) MIN. INTO CONC. @ 7'-10" (2390) O.C. 4" (100) HIGH INTAKE VENTS. HRV INTAKE TO BE A MIN. OF 6'-0" (1830) FROM ALL EXHAUST ELEVATION, CONTINUOUS SOFFIT, 4" PRE-FINISHED ALUMINUM EAVESTROUGH WITH
CONC. CURB ON CONC. FOOTING. FOR SIZE REFER TO HEX NOTE 5. ADD TERMINALS. REFER TO GAS UTILIZATION CODE.
HORIZ. BLOCKING AT MID-HEIGHT IF WALL IS UNFINISHED. 1% SLOPE TO 3-1/2" PREFINISHED ALUMINUM RAING WATER LEADERS DRAINING
FIREPLACE VENTING (9.32.3.)
K15
ADJUSTABLE STEEL BASEMENT COLUMN (9.15.3.4.)
9'-10" (3000) MAX. SPAN BETWEEN COLUMNS. 3 1/2" (90)Ø SINGLE TUBE
ADJUSTABLE STEEL COLUMN CONFORMING TO CAN/CGSB-7.2M, AND WITH
K33
DIRECT VENT GAS FIREPLACE VENT TO BE A MIN. 12" (305) FROM ANY
OPENING AND ABOVE FIN. GRADE. REFER TO GAS UTILIZATION CODE.
ONTO 1'-0"x2'-0" CONCRETE SPLASH PAD.
PROVIDE EAVESTROUGHS, ROOF SCUPPERS AND DOWNSPOUTS FOR EACH
DWELLING UNIT IN THE CASE OF SEMI-DETACHED, TOWNHOUSES, AND ROW
CONSTRUCTION
FLOOR FRAMING (9.23.3.5., 9.23.9.4., 9.23.14.)
6"x6"x3/8" (152x152x9.5) STEEL PLATE TOP & BOTTOM. FIELD WELD BASEMENT
COLUMN CONNECTION. POURED CONCRETE FOOTING ON NATURAL
K34
T&G SUBFLOOR ON WOOD FLOOR JOISTS. FOR CERAMIC TILE APPLICATION
SEE O.B.C. 9.30.6. ALL JOISTS WHERE REQUIRED TO BE BRIDGED WITH 2"x2"
HOUSING DWELLING UNITS.
FLASHING AND STEPPED FLASHING 9.20.13 OBC
NOTES
CONSTRUCTION NOTES
UNDISTURBED SOIL OF 75kPa OR COMPACTED ENGINEERED FILL WITH MIN. K51

(38x38) CROSS BRACING OR SOLID BLOCKING @ 6'-11" (2108) O.C. MAX. ALL INSTALL ALUMINUM FLASHING REGLETED AND CAULKED INTO
BEARING CAPACITY OF 150kPa AS PER SOILS REPORT.
JOISTS TO BE STRAPPED WITH 1"x3" (19x64) @ 6'-11" (2108) O.C. UNLESS A MASONRY OR 6" UP UNDER EXTERIOR FINISH. STEP FLASHING MIN.
SUPPORTING 2 STOREY FLR. LOAD PROVIDE 34"x34"x16" (870x870x410)CONC. FOOTING PANEL TYPE CEILING FINISH IS APPLIED. HORIZONTAL RUN 3: LAP COUNTER FLASHING MIN. 6" VERTICALLY
SUPPORTING 3 STOREY FLR. LOAD PROVIDE 40"x40"x19" (1060x1060x480) CONC. FOOTING
SKYLIGHT FRAMING 9.7 OBC
HEADER CONSTRUCTION K52
A-001
K34A PROVIDE DOUBLE JOIST OR ROOF MEMBER FRAMING AROUND ALL SKYLIGHT
PROVIDE CONTINUOUS APPROVED AIR/VAPOUR BARRIER (HEADER WRAP)
UNDER THE SILL PLATE, AROUND THE RIM BOARD AND UNDER THE OPENINGS.
BOTTOM PLATE. THE HEADER WRAP SHALL EXTEND 6" (152) BELOW THE INSTALL SELF FLASHING SKYLIGHTS AS PER MANUFACTURER'S SPECIFICATIONS
TOP OF FOUNDATION WALL AND WILL BE SEALED TO THE CONCRETE AND RECOMMENDED PROCEDURES. CAULK ALL JOINST
FOUNDATION WALL. EXTEND HEADER WRAP 6" (152) UP THE INTERIOR SIDE
OF THE STUD WALL AND OVERLAP WITH THE VAPOUR BARRIER AND SEAL
THE JOINT. ALL EDGES/JOINTS MUST BE MECHANICALLY CLAMPED.
ON
PROJECT NAME
LEGEND
NEW WALL CMA CO 13948 Mississauga
ALARM
LOADBEARING Road, Caledon ON
WALL SA SMOKE
ALARM PROJECT ADDRESS
X WALL TYPE
2 1 INTERIOR
A-400b A-400b FIRE
DENOTES WELDED BLOCKED
CONNECTION STEEL WALLS ON
DENOTES BOLTED CONNECTION
CONNECTION
75'-0"
48'-2" 26'-10"
CLIENT
10'-3" 15'-8" 14'-2" 8'-1" 2'-11" 9'-4" 2'-4" 9'-4" 2'-11"
GENERAL FLOOR PLAN NOTES
10" 47'-4" 10" 25'-2" 10" 1. CONTRACTOR/BUILDER TO REVIEW AND COORDINATE
WITH ALL CONSULTANT DRAWINGS PRIOR TO
HARVINDER D.
CONSTRUCTION.
2. ALL SMOKE ALARMS TO BE INTERCONNECTED AND
RESIDENCE
WOOD STAIRS, PROVIDE
CONC. PAD AT HARD WIRED. SEE FLOOR PLANS FOR LOCATIONS AND
LANDING
CONFORM TO 9.10.19 OF THE OBC.
UP13R
CONTRACTOR TO INSTALL CARBON MONOXIDE ARCHITECT
DETECTORS IN EACH FLOOR AS PER OBC 9.33.4
KHALSA DESIGN INC.
10"
10"
10"
10"
K10 3. FINAL KITCHEN LAYOUT TO BE DETERMINED BY OWNER.
2'-2"
CHECK FOUNDATION FOR O.H CHECK FOUNDATION FOR O.H 4. ALL INTERIOR FINISHES TO BE DETERMINED BY OWNER.
10"
DOOR ABOVE DOOR ABOVE
L. "
L. "
5" SS.
1'-11"
CO /8
CO /8
5. REFER TO CONSTRUCTION NOTES ON SHEET A-002 FOR
x5 C
H
S. x3
S. x3
" x OL
HS "x5"
HS "x5"
3/ .
3'-4"
W10x45 W10x45
NOTES AND INFORMATION
8"
5
4'-2"
4'-2"
3'-4"
3'-4"
4'-2"
10'-10"
K11
K11
6. MOISTURE RESISTANT GWB. BOARD TO BE USED IN ALL
K10
K10 BATHROOMS AND KITCHENS
UP 5R UP 5R 7. SEE EXTERIOR ELEVATIONS FOR WINDOW TYPES &
16'-8" 2'-0" 10'-4" 2'-0" 15'-2" CLADDING MATERIALS
14'-8"
JOISTS AT 12" O.C.

2x10 PT. SPR #2
13'-10"
8. ALL INTERIOR DIMENSIONS ARE FROM FACE OF GWB TO
13'-10"
2'-0" K11
FACE GWB
11'-5"
9. ALL EXTERIOR DIMENSIONS ARE FROM EXTERIOR FACE
L3
L3
10'-0"
9'-2"
K11
OF EXTERIOR WALL FINISH, TYP., U.N.O.
9'-7"
8" F.D. 31'-6" 10" 3'-6" F.D.
10. REFER TO FLOOR/TRUSS MANUFACTURER DRAWINGS

10" 47'-4" FOR DETAILS AND SPECIFICATIONS.
5'-0"
11. ELECTRICAL OUTLETS ON OPPOSITE SIDE OF WALL
SHOULD BE INSTALLED AT LEAST 2'-0" FROM EACH OTHER.
W10x39+8"x1/4" STL. PL.(DRP.) W10x39+8"x1/4" STL. PL.(DRP.) LVL 4+L7
10" 12. CONTRACTOR TO VERIFY EXISTING SITE CONDITIONS
64"x96" IN THE FIELD PRIOR TO CONSTRUCTION.
13. CONTRACTOR TO PROVIDE BLOCKING AS REQUIRED
5" SS.
L. "
CO /8
5" SS.
x5 C
144"x96"
H
x5 C
S. x3
H
" x OL
FOR CABINETS & FOR FUTURE INSTALLATION OF GRAB
" x OL
HS "x5"
3/ .
3/ .
8"
5
8"
BARS.
14. CONTRACTOR TO COORDINATE ALL INTERIOR
BRAMPTON, ON
38'-4"
37'-6"
ACCESSORIES WITH OWNER AND TO SUPPLY ADEQUATE
BLOCKING.
40'-2"
40'-2"
15. PROVIDE RESILENT FLOORING IN CONFORMANCE TELEPHONE: 647-468-2940
WITH 9.30.1.2 OF THE OBC.
16. PROVIDE ACOUSTICAL INSULATION BETWEEN
11-7/8" ENG. JOISTS @ 12" O.C.

HALLWAY AND BEDROOM WALLS AS PER OWNERS
REQUEST.
CONSULTANTS:
20'-4"
17. PROVIDE FIRE BLOCKING AS PER 9.10.16 OF THE
ONTARIO BUILDING CODE AT LOCATIONS WITHIN THE
WALL SO THAT DISTANCE BETWEEN FIRE BLOCKS DOES NOT MEM ENGINEERING INC.
EXCEED 20m (65'-6") HORIZONTALLY AND 3m (9'-10" FT)
VERTICALLY. STRUCUTRAL SEAL:
18. ALL DOORS ON PLANS ARE 7'-10" UNLESS NOTED
K15C -NON ADJUSTABLE STEEL COL. CUSTOMIZED STEEL U OTHERWISE.
5"x5"x3/8" HSS STEEL POST w/ SHAPED HANGER w/
34'-0"
8"x8"x3/8" TOP & BOTTOM PLATES, 1/2" STIFFENERS @ 18" 19. REFER TO FLOOR JOIST MANUFACTURER DRAWINGS
FIELD WELD COLUMN TO TOP & BASE O.C. BOTH SIDES (TYP.) FOR LAYOUT, SPACING, BLOCKING, & STRAPPING
PLATE, STEEL COL. ON 48"x48"x24"
CONC. FOOTING (TYP.) REQUIREMENTS, INSTALLATION DETAILS AND HANGER
BEAM 3'-3" 10'-6" 1'-0" 2'-9"
POCKET K15C
SIZES, & SUBFLOOR THICKNESS
(TYP.)
W10x39 (DRP.) W10x54 (DRP.) W10x39 (DRP.)
20. PROVIDE SOLID BLOCKING @ 24" O.C. FOR FIRST JOIST
2'-0"
SPAN WHEN PARALLEL w/ EXTERIOR WALL
PL
PL
PL
21. ALL SUBFLOOR TO BE 3/4" OS.B. (COORDINATE w/
K15C
FLOOR MANUF. DRAWINGS)
11-7/8" ENG. JOISTS
LVL 6 (FL.)
22. POUR IN PLACE CONCRETE STEPS WITH MASONRY

5'-6"
4 @ 16" O.C.
VENEER ON SIDES IF REQUIRED BY GRADE.
79'-4"
79'-4"
2'-8"
A-400a 6'-10" 14'-8" 10'-6" 10" 25'-2" 9'-9" 10"
K15C 23. FOOTINGS TO REST ON NATURAL UNDISTURBED SOIL
LVL 6 (FL.) STRENGTH OF 75 KPa (TYPICAL)
PL
PL
10"
10"
10"
ROUGH-
55'-2"
53'-6"
K32 IN ONLY 10"

4'-0" 11'-5" 10" 4'-9" 10" 4'-2"
LV
W10x45 (FL.)
FURNACE
15'-10"
L
11-7/8" ENG. JOISTS @ 16" O.C.

6
L 3
CHECK FOUNDATION FOR

LV
F.D.
W10x39 (DRP.)
STEEL CONSTRUCTIN NOTES:
STAIRS ABOVE
ROUGH-
HRV
9'-2"
9'-2"
W10x39 (DRP.)
IN ONLY
9'-10"
22'-4"
HWT 1. ALL STRUCTURAL STEEL SHALL CONFORM TO C.S.A. COPYRIGHT KDI © 2023
G40.21-92 WITH A MINUMUM YEILD STRENGTH OF 350 THESE DRAWINGS ARE NOW AND DO
LVL 6+L7
K42 ROUGH- 11-7/8" ENG. JOISTS

MPa. REMAIN THE SOLE PROPERTY OF KHALSA
IN ONLY @ 16" O.C.
16'-10"
K44
2. STEEL STEEL DETAILING AND CONNECTION TO FORM OF REPRODUCTION OF THIS DESIGN

K15C K15C IN WHOLE OR IN PART WITHOUT EXPRESS
LOAD-BEARING W10x39 (DRP.) CONFORM TO C.S.A. CAN-3S16.1-94
11"
K11
WALLS WRITTEN CONSENT IS PROHIBITED AND
LOAD BEARING CMA SHALL RESULT IN THE FULLEST EXTENT OF
WALLS ON 24x8" PAD 3. ALL WEDLING SHALL BE IN CONFORMANCE WITH
FOOTING (TYP.)
SA PROSECUTION UNDER LAW
LVL 7 C.S.A. W59-M1989 AND TO THE REQUIREMENTS OF
31'-6"
W47.1-92 AND SHALL UTILIZE E480XX ELECTRODES.
PL
PL
LV
K10 11-7/8" ENG. JOISTS CUSTOMIZED STEEL U

ARCHITECT SEAL:
L
PL
SHAPED HANGER w/
3
@ 16" O.C.
8R
4'-2"
L
LV
1/2" STIFFENERS @ 18"

1
UP
O.C. BOTH SIDES (TYP.)
W10x39 (DRP.)
K15C K10
11-7/8" ENG. JOISTS @ 12" O.C.

W10x45 (DRP.)
TW TALL WALL DETAIL

21'-2"
11-7/8" ENG. JOISTS @ 16" O.C. 11-7/8" ENG. JOISTS @ 16" O.C.
17'-4"
17'-4"
17'-1"
1 11-7/8" ENG. JOISTS @ 12" O.C. WALL HEIGHT LESS THAN 22'-0" 05 - 02 - 2024
TALL WALL FRAMED W/2-2x6 @ 16" O.C. FULL
W10x45 (FL.)
A-400a
K29
HEIGHT WD STUDS 3 ROW OF SOLID
10'-10"
BLOCKING C/W 3/4" EXT. GRADE PLYWOOD

12'-4"
T&G SHEATHING, (3)2x6 FULL HEIGHT WOOD

13'-10"
COLUMNS, MECHANICALLY FASTENED SILLS,

LVL 5
15'-4" 21'-6" 14'-6" 22'-0" COLUMNS & TOP/BOTTOM PL STUDS &

5'-3"
HEADER W/ SIMPSON STRONG TIE (A-23

CLIP) AT EACH SIDE
K42 K44
Date 05/02/2024
K28 K42 K44 Drawn by ASB
10" 8" 10"
10" 10"
WALL HEIGHT GREATER THAN 22'-0"
2"
K42 K44 K42 K44
KDI
1'-0"
1'-0"
TALL WALL FRAMED W/2-2x6 @ 16" O.C. LSL Checked by
1'-6"
1'-6"
1'-6"
LVL 6+L7
1C LVL 6+L7 FULL HEIGHT WD STUDS 3 ROW OF SOLID Scale As indicated

LVL 6+L7 LVL 6+L7
10"
W6x25 (DRP.) T&G SHEATHING REVISIONS

11" 7" 10" 2'-8" 10" 11'-2" 10" 2'-8" 10" 7" 11" 25MPa POURED CONC. FOUNDATION
WALL ON 24"x8" DEEP POURED CONC. No. Description Date
7'-8"
K6
7'-2"
8'-6"
K12 K5C FOOTING w/ 15M @ 10" O.C. HORIZONTAL
8'-0"
8'-0"
WT5
5'-8"
K13 K34A AND 15M @ 10" O.C. VERTICAL BARS.

FOOTINGS TO BEAR ON UNDISTRUBED SOIL
LEGEND 1
w/ 2-15M CONT. BAR REBAR (TYP.) 3.1. WOOD LINTELS AND BUILT-UP WOOD
(DIVISION B PART 9. TABLES A8 TO A10 AND A12, A15 & A16)
FORMING PART OF SENTENCE 9.23.4.2.(3), 9.23.4.2.(4), 9.23.12.3.(1),(3), 9.23.13.8.(2), 9.37.3.1.(1)
10"
10"
10"
2"x8" SPRUCE #2 2"x10" SPRUCE #2 2"x12" SPRUCE #2
L1 2/2"x8" (2/38x184) L3 2/2"x10" (2/38x235) L5 2/2"x12" (2/38x286)
2'-11"
B1 3/2"x8" (3/38x184) B3 3/2"x10" (3/38x235) B5 3/2"x12" (3/38x286)

3'-8"
B2 4/2"x8" (4/38x184) B4 4/2"x10" (4/38x235) B6 4/2"x12" (4/38x286)

GC TO VERIFY NUMBER
B7 5/2"x8" (5/38x184) B8 5/2"x10" (5/38x235) B9 5/2"x12" (5/38x286)
9"
OF RISERS PRIOR TO ENGINEERED LUMBER SCHEDULE 2.0E-3300 BY GLOBAL LVL OR EQUAL

POURING CONC. 2'-2" 10" 13'-10" 10" 2'-2" 1 3/4" x 9 1/2" LVL 1 3/4" x 11 7/8" LVL 1 3/4" x 14" LVL
LVL2 1-1 3/4"x9 1/2" LVL3 1-1 3/4"x11 7/8" LVL10 1-1 3/4"x14"
LVL4 2-1 3/4"x9 1/2" LVL6 2-1 3/4"x11 7/8" LVL11 2-1 3/4"x14"
LVL5 3-1 3/4"x9 1/2" LVL7 3-1 3/4"x11 7/8" LVL12 3-1 3/4"x14"
10" 8" 10" 11'-8" 1'-6" 11" 7" 10" 2'-8" 10" 11'-2" 10" 2'-8" 10" 7" 11" 2'-0" 10" 10'-9" 11" 6'-6" 10" 10'-3" 10" 2'-11" 10" LVL8 4-1 3/4"x9 1/2" LVL9 4-1 3/4"x11 7/8" LVL13 4-1 3/4"x14"
6'-3" 6'-3" 6'-5" 6'-5" 6'-3" 6'-3" 5'-11 1/2" 5'-11 1/2" LVL14 1-1 3/4"x7 1/4" LVL15 2-1 3/4"x7 1/4" LVL16 3-1 3/4"x7 1/4"
STEEL LINTELS SUPPORTING MASONRY VENEER
1'-6" 12'-6" 1'-6" 1'-6" 3'-6" 12'-10" 3'-6" 1'-6"
75'-0"
2'-0" 12'-6" 6'-6" 11'-11" 3'-9"
CODE SIZE
(DIVISION B PART 9. TABLE 9.20.5.2.B.)
FORMING PART OF SENTENCE 9.20.5.2.(2) & 9.20.5.2.(3)
BRICK STONE
BASEMENT
L7
L8
3 1/2" x 3 1/2" x 1/4" (89 x 89 x 6.4)
4" x 3 1/2" x 1/4" (102 x 89 x 6.4)
8'-1" (2.47m)
8'-9" (2.66m)
7'-6" (2.30m)
8'-1" (2.48m) FLOOR PLAN
L9 4 7/8" x 3 1/2" x 5/16" (127 x 89 x 7.9) 10'-10" (3.31m) 10'-1" (3.03m)
L10 4 7/8" x 3 1/2" x 3/8" (127 x 89 x 11) 11'-5" (3.48m) 10'-7" (3.24m)
L11 5 7/8" x 3 1/2" x 3/8" (152 x 89 x 11) 12'-6" (3.82m) 11'-7" (3.54m)
A-101
L12 7 1/8" x 4" x 3/8" (178 x 102 x 11) 14'-1" (4.30m) 13'-1" (3.99m)
BASEMENT FLOOR PLAN

1 13948 Mississauga Road, Caledon
3/16" = 1'-0"
ON
PROJECT NAME
LEGEND
ALARM
WALL SA SMOKE
2 1 X WALL TYPE
INTERIOR
A-400b A-400b FIRE
CONNECTION
75'-0"
48'-2" 26'-10" CLIENT

5'-0" 9'-6" 11'-5" 14'-3" 8'-0" 2'-11" 9'-4" 2'-4" 9'-4" 2'-11" GENERAL FLOOR PLAN NOTES
11" 47'-3" 11" 25'-0" 11"
1. CONTRACTOR/BUILDER TO REVIEW AND COORDINATE
HARVINDER D.
CONSTRUCTION.
RESIDENCE
LVL 7 ABOVE GARAGE TRANSOM WINDOW HARD WIRED. SEE FLOOR PLANS FOR LOCATIONS AND
DOOR AND ABOVE HIGH ABOVE GARAGE CONFORM TO 9.10.19 OF THE OBC.
WINDOWS DOOR, SEE ELEV.
9'x10' 9'x10' DETECTORS IN EACH FLOOR AS PER OBC 9.33.4
KHALSA DESIGN INC.
11"
11"
11"
K11 3. FINAL KITCHEN LAYOUT TO BE DETERMINED BY OWNER.
2'-2"
5" SS.
K10 4. ALL INTERIOR FINISHES TO BE DETERMINED BY OWNER.
SB
SB
SB
SB
SB
x5 C
5" SS.
" x OL
O "
x5 C
C /8
H
3/ .
5. REFER TO CONSTRUCTION NOTES ON SHEET A-002 FOR
" x OL
S. "x3
L.
CONT. W10x45 (DRP.)
8"
3/ .
HS "x5
8"
7"
36"x96"
3'-4"
10'-10"
L1
BATHROOMS AND KITCHENS
7. SEE EXTERIOR ELEVATIONS FOR WINDOW TYPES &
CLADDING MATERIALS
14'-8"
14'-8"
3'-11"
13'-4"
8. ALL INTERIOR DIMENSIONS ARE FROM FACE OF GWB TO
13'-9"
13'-9"
JOISTS AT 12" O.C.
2x10 PT. SPR #2
COVERED DECK FACE GWB
12'-0"
11'-5"
L3
L3
9. ALL EXTERIOR DIMENSIONS ARE FROM EXTERIOR FACE
L1
DN13R OF EXTERIOR WALL FINISH, TYP., U.N.O.
K11 10. REFER TO FLOOR/TRUSS MANUFACTURER DRAWINGS
FOR DETAILS AND SPECIFICATIONS.
5'-0"
O "
O "
C /8
C /8
33'-0" 3'-7" 11'-7"
S. "x3
S. "x3
L.
L.
HS "x4
HS "x4
W250x33
11"
9'-9"
B3
4
LVL 5 W10x45 (DRP.) LVL 5 12. CONTRACTOR TO VERIFY EXISTING SITE CONDITIONS
11-7/8" ENG. JOISTS

@ 12" O.C.
11" 36"x96" IN THE FIELD PRIOR TO CONSTRUCTION.
SB
PL
PL
SB
SB
SB
PL
4" SS.
4" SS.
SB
SB
144"x96"
x4 C
x4 C
H
H
" x OL
" x OL
TW FOR CABINETS & FOR FUTURE INSTALLATION OF GRAB
3/ .
3/ .
8"
8"
6'-5"
BARS.
12'-1"
6'-1" 6" 41'-1" 6" 25'-0" 14. CONTRACTOR TO COORDINATE ALL INTERIOR
BRAMPTON, ON
L1
K19
KITCHEN BLOCKING.
41'-10"
40'-0"
13'-4"
40'-0"
GAS SEAL
4 CAR 15. PROVIDE RESILENT FLOORING IN CONFORMANCE
L1
WALLS/CEILING TELEPHONE: 647-468-2940

BETWEEN HOUSE GARAGE WITH 9.30.1.2 OF THE OBC.
11-7/8" ENG. JOISTS @ 12" O.C.

& GARAGE
DV. GAS FIREPLACE

FAMILY ROOM HALLWAY AND BEDROOM WALLS AS PER OWNERS
CONSULTANTS:
11'-3"
W10x39 (FL.)
SPICE KITCHEN REQUEST.
20'-0"
20'-3"
(OPEN TO 17. PROVIDE FIRE BLOCKING AS PER 9.10.16 OF THE
ABOVE) STRUCTURAL ENGINEER:
O "
O "
C /8
C /8
S. "x3
S. "x3
L.
L.
HS "x4
HS "x4
K37 W250x33 WALL SO THAT DISTANCE BETWEEN FIRE BLOCKS DOES NOT
4
K37
18. ALL DOORS ON PLANS ARE 7'-10" UNLESS NOTED
L1
OTHERWISE.
19. REFER TO FLOOR JOIST MANUFACTURER DRAWINGS
FOR LAYOUT, SPACING, BLOCKING, & STRAPPING
11-7/8" ENG. JOISTS

@ 16" O.C.
REQUIREMENTS, INSTALLATION DETAILS AND HANGER
2'-7"
13'-4"
OVEN
6'-1" SIZES, & SUBFLOOR THICKNESS

WALL
6" 3'-0" REF. 7'-4" 12'-0" 6'-0" 4'-0" 6'-2"
4" SS.
O "
C /8
27'-7"
x4 C
H
S. "x3
L.
" x OL
HS "x4
3/ .
W10x39 (FL.) LVL 7 (FL.)
8"
4"
LVL 7 (FL.)
SB
SB
SB
11'-5"
6"
6"
72'-10"
72'-10"
21'-6"
PANTRY FLOOR MANUF. DRAWINGS)
6'-5"
6'-0"
LVL 6
LVL 6
5'-3"
4
4 K26 22. POUR IN PLACE CONCRETE STEPS WITH MASONRY
11-7/8" ENG. JOISTS

@ 16" O.C.
3'-6"
.)
3A
FL
A-400a
LV
5'-0" 6'-8" 13'-4"
6(
8'-0"
4"
L
4" 23. FOOTINGS TO REST ON NATURAL UNDISTURBED SOIL
L
6(
K20
K19
LV
8'-4" 4" 7'-0" 2'-0" W10x39 (DRP.) 23'-8" 4" 5'-4" 6" LVL 6
FL
STRENGTH OF 75 KPa (TYPICAL)

.)
6"
11"
SB
SB
55'-2"
53'-4"
36"x96"
4" SS.
O "
C /8
6"
x4 C
H
K11
S. "x3
DN
L.
" x OL
11"
3/ .
4'-9 1/2"
HS "x4
18
4'-3 1/2"
9'-8" 11"
8"
LOAD-BEARING WALL
SA
R
CMA
4'-8"
10'-7"
11-7/8" ENG. JOISTS

@ 16" O.C.
4"
SB
18'-4"
COVERED
8'-1"
PORCH
3A
42"x96"
9'-2"
9'-5"
B3
UP 6R
LVL 7 (FL.)
5'-1"
11-7/8" ENG. JOISTS @ 16" O.C. MUDROOM 1. ALL STRUCTURAL STEEL SHALL CONFORM TO C.S.A.
K10
G40.21-92 WITH A MINUMUM YEILD STRENGTH OF 350 THESE DRAWINGS ARE NOW AND DO
13'-4"

14'-4"
LVL 4
LOAD-BEARING WALL
4'-6"
K11 6" 5'-0" 4" 5'-4" 4" 7'-6" 4" 6'-9" 5'-7" 5'-0" MPa.
DINING DESIGN USE OF THESE PLANS OR ANY
16'-4"
6"
6"
42"x96" 2. STEEL STEEL DETAILING AND CONNECTION TO FORM OF REPRODUCTION OF THIS DESIGN
K11
K11 LVL 7 (FL.) CONFORM TO C.S.A. CAN-3S16.1-94
SB
WRITTEN CONSENT IS PROHIBITED AND
8"
4'-5"
SB
SA 3. ALL WEDLING SHALL BE IN CONFORMANCE WITH
6'-9"
3'-9" 3'-9"
CMA
4'-0"
W.I.C. C.S.A. W59-M1989 AND TO THE REQUIREMENTS OF
2
LVL 6 (FL.) SA
SB
SB
SB
6"
6"
K10
K10 10'-0" 2'-1" 6" 4'-0" 6'-0" 4" 11'-0"
ARCHITECT SEAL:
28'-10"
SB
UP
1'-11" 4" 3A
8R
18
26'-0 1/2"
1
1'-0"
R
UP
4"
4"
11-7/8" ENG. JOISTS @ 16" O.C.

11-7/8" ENG. JOISTS @ 16" O.C.
6'-9" 7'-6" 6'-9"
TW TALL WALL DETAIL
21'-2"
21'-0"
18'-10"
17'-0"
1 WALL HEIGHT LESS THAN 22'-0" 05 - 02 - 2024
12'-0"
12'-0"
A-400a K26 GUEST

LIVING STUDY
12'-8"
LVL 5
15'-6"
15'-6"
BEDROOM HEIGHT WD STUDS 3 ROW OF SOLID
11'-10"
12'-6"
ENS. T&G SHEATHING, (3)2x6 FULL HEIGHT WOOD

14'-0"
COLUMNS, MECHANICALLY FASTENED SILLS,

COLUMNS & TOP/BOTTOM PL STUDS &
HEADER W/ SIMPSON STRONG TIE (A-23 Project number 24003
3A
15'-0"
6"
21'-0" 6" 14'-0" 6" 6'-0" 4" 15'-4"
CLIP) AT EACH SIDE
Date 05/02/2024
1'-0"
1'-0"
SB
SB
SB
SB
PL
PL
SB
Drawn by ASB
PL
PL
11" 7" 11" 7" 11"
11" 1'-1" 11" 11"

1"
W10x39+8"x1/4" STL. PL.(DRP.) TW TW W10x39+8"x1/4" STL. PL.(DRP.) WALL HEIGHT GREATER THAN 22'-0"
SB
SB
KDI
1'-0"
1'-0"
1'-6"
1'-6"
1'-6"
1'-6"
L1+L7
SB
SB
SB
SB
L3+L9 FULL HEIGHT WD STUDS 3 ROW OF SOLID Scale As indicated
2'-0"
L1+L7 L3+L9
1'-6"
1'-6"
1'-6"
L3+L9 L1+L7
SB

SB
LVL 4
T&G SHEATHING REVISIONS
72"x108"
COVERED PORCH LEGEND 1

3.1. WOOD LINTELS AND BUILT-UP WOOD
O "
O "

C /8
C /8
S. "x3
S. "x3
L.
L.

HS "x5
HS "x5
16"x16" BRICK VENEER PIER w/

5
10"x10" SIDING CLAD COL. 2"x8" SPRUCE #2 2"x10" SPRUCE #2 2"x12" SPRUCE #2
ABOVE WITH 5"x5"x3/8" STEEL L1 2/2"x8" (2/38x184) L3 2/2"x10" (2/38x235) L5 2/2"x12" (2/38x286)
HSS. POST AT CENTER w. GALV.
BASE SHOE ANCHORED TO
B1 3/2"x8" (3/38x184) B3 3/2"x10" (3/38x235) B5 3/2"x12" (3/38x286)
CONC. (TYP.) B2 4/2"x8" (4/38x184) B4 4/2"x10" (4/38x235) B6 4/2"x12" (4/38x286)
B7 5/2"x8" (5/38x184) B8 5/2"x10" (5/38x235) B9 5/2"x12" (5/38x286)
ENGINEERED LUMBER SCHEDULE 2.0E-3300 BY GLOBAL LVL OR EQUAL
1 3/4" x 9 1/2" LVL 1 3/4" x 11 7/8" LVL 1 3/4" x 14" LVL
LVL2 1-1 3/4"x9 1/2" LVL3 1-1 3/4"x11 7/8" LVL10 1-1 3/4"x14"
11" 7" 11" 10'-8" 11" 1'-6" 11" 4'-1" 11" 11'-0" 11" 4'-1" 11" 2'-0" 11" 10'-8" 11" 6'-6" 11" 10'-1" 11" 2'-10" 11" LVL4 2-1 3/4"x9 1/2" LVL6 2-1 3/4"x11 7/8" LVL11 2-1 3/4"x14"
LVL5 3-1 3/4"x9 1/2" LVL7 3-1 3/4"x11 7/8" LVL12 3-1 3/4"x14"
6'-3" 6'-3" 2'-6" 2'-6" 6'-5" 6'-5" 2'-6" 2'-6" 6'-3" 6'-3" 3'-7" 2'-11" 5'-11 1/2" 5'-11 1/2"
LVL8 4-1 3/4"x9 1/2" LVL9 4-1 3/4"x11 7/8" LVL13 4-1 3/4"x14"
1'-6" 12'-6" 1'-6" 5'-0" 12'-10" 5'-0" 2'-0" 12'-6" 6'-6" 11'-11" 3'-9" LVL14 1-1 3/4"x7 1/4" LVL15 2-1 3/4"x7 1/4" LVL16 3-1 3/4"x7 1/4"
STEEL LINTELS SUPPORTING MASONRY VENEER
75'-0"
CODE SIZE
BRICK STONE
GROUND FLOOR
GROUND FLOOR PLAN
3452 sq ft
L7
L8
3 1/2" x 3 1/2" x 1/4" (89 x 89 x 6.4)
4" x 3 1/2" x 1/4" (102 x 89 x 6.4)
8'-1" (2.47m)
8'-9" (2.66m)
7'-6" (2.30m)
8'-1" (2.48m) PLAN
L9 4 7/8" x 3 1/2" x 5/16" (127 x 89 x 7.9) 10'-10" (3.31m) 10'-1" (3.03m)
GROSS FLOOR AREA 3452 sq ft L10 4 7/8" x 3 1/2" x 3/8" (127 x 89 x 11) 11'-5" (3.48m) 10'-7" (3.24m)
GARAGE FLOOR AREA 1084 sq ft
DEDUCT OPEN AREAS 0 sq ft L11 5 7/8" x 3 1/2" x 3/8" (152 x 89 x 11) 12'-6" (3.82m) 11'-7" (3.54m)
A-102
COVERAGE W/O PORCH 4536 sq ft L12 7 1/8" x 4" x 3/8" (178 x 102 x 11) 14'-1" (4.30m) 13'-1" (3.99m)
COVERAGE W/ PORCH 4723 sq ft
1-1ST FLOOR
3/16" = 1'-0"
ON
PROJECT NAME
LEGEND
ALARM
WALL SA SMOKE
X WALL TYPE
INTERIOR
FIRE
2 1 DENOTES BOLTED CONNECTION
CONNECTION
A-400b A-400b
CLIENT
74'-6"
48'-2" 26'-4"
GENERAL FLOOR PLAN NOTES
9'-5" 11'-9" 6'-2" 12'-7" 8'-3" 3'-8" 9'-6" 9'-6" 3'-8" 1. CONTRACTOR/BUILDER TO REVIEW AND COORDINATE
HARVINDER D.
8" 47'-6" 8" 25'-0" 8"
CONSTRUCTION.
RESIDENCE
HARD WIRED. SEE FLOOR PLANS FOR LOCATIONS AND
CONFORM TO 9.10.19 OF THE OBC.
DETECTORS IN EACH FLOOR AS PER OBC 9.33.4
LVL 5 LVL 12 LVL 5
3. FINAL KITCHEN LAYOUT TO BE DETERMINED BY OWNER. KHALSA DESIGN INC.
8"
8"
5" 19'-0" 12'-6" 5"
2'-5"
4. ALL INTERIOR FINISHES TO BE DETERMINED BY OWNER.
SB
SB
SB
SB
SB
SB
O "
O "
O "
2'-6"
C /8
C /8
C /8
CONT. W10x45 (DRP.) 5. REFER TO CONSTRUCTION NOTES ON SHEET A-002 FOR
S. "x3
S. "x3
S. "x3
L.
L.
L.
25'-0"
HS "x5
HS "x5
HS "x5
L1
8"
5
BATHROOMS AND KITCHENS
ALL ENGINEERED LUMBER 2'-6" 20'-0" 2'-6"
TO BE WRAPPED WITH
3'-10" 7. SEE EXTERIOR ELEVATIONS FOR WINDOW TYPES &
ENG. ROOF TRUSSES

BLUESKIN AND CLADDED NOTE: ALL CLADDING MATERIALS
CEILINGS TO BE
14'-8"
w/ PVC BOARD OR 8. ALL INTERIOR DIMENSIONS ARE FROM FACE OF GWB TO
14'-0"
SIMILAR. FLASH & SEAL ALL BUILT DOWN
FACE GWB
G.T. BY ROOF
G.T. BY ROOF
MANUF.
MANUF.
JOINTS AND ENG. ROOF TRUSSES FROM TRUSSES
11'-8"
PENETRATIONS PRIMARY 9. ALL EXTERIOR DIMENSIONS ARE FROM EXTERIOR FACE
LVL 4
LVL 4
COVERED DECK
13'-0"
18'-0"
14'-8"
BEDROOM OF EXTERIOR WALL FINISH, TYP., U.N.O.
4'-0" 10. REFER TO FLOOR/TRUSS MANUFACTURER DRAWINGS
3'-10" FOR DETAILS AND SPECIFICATIONS.
LVL 12 LVL 4 LVL 6 LVL 12 12. CONTRACTOR TO VERIFY EXISTING SITE CONDITIONS
G.T. BY ROOF IN THE FIELD PRIOR TO CONSTRUCTION.
8"
MANUF.
SB
SB
SB
SB
SB
SB
SB
SB
SB
144"x96" 36"x96"
FOR CABINETS & FOR FUTURE INSTALLATION OF GRAB
3'-0"
3'-0"
L1
2'-6"
SA BARS.
14. CONTRACTOR TO COORDINATE ALL INTERIOR
3A BRAMPTON, ON
4"
10"
18'-0" 6" 3'-10" 25'-4" 6" 6'-10" 17'-10" BLOCKING.
4" 15. PROVIDE RESILENT FLOORING IN CONFORMANCE
W.I.C. TELEPHONE: 647-468-2940
WITH 9.30.1.2 OF THE OBC.
16'-6"
HALLWAY AND BEDROOM WALLS AS PER OWNERS
10'-0"
BEDROOM 2 CONSULTANTS:
10'-0"
18'-5"
REQUEST.
21'-0"
16'-5"
20'-0"
14'-0"
17. PROVIDE FIRE BLOCKING AS PER 9.10.16 OF THE
WALL SO THAT DISTANCE BETWEEN FIRE BLOCKS DOES NOT MEM ENGINEERING INC.
2
4"
3'-10" 3'-0" 19'-4" 3'-0" 18. ALL DOORS ON PLANS ARE 7'-10" UNLESS NOTED
3
6"
3'-11 1/2"
OTHERWISE.
3A SA 19. REFER TO FLOOR JOIST MANUFACTURER DRAWINGS
FREESTANDING
3A
4"
4"
FOR LAYOUT, SPACING, BLOCKING, & STRAPPING

PRIMARY
ENG. ROOF TRUSSES

REQUIREMENTS, INSTALLATION DETAILS AND HANGER
8'-0"
TUB
ENSUITE
3'-0"
L1
SIZES, & SUBFLOOR THICKNESS
G.T. BY ROOF
MANUF.
3
4"
68'-0"
69'-7"
11'-10"
K11
11'-2"
72'-7 1/2"
L1
FIRE
72'-7"
5'-11"
ENS. 2 W.I.C. BLOCKING
IN WALL AT
ATTIC FLOOR MANUF. DRAWINGS)
7'-2"
4"
11'-6"
5'-10"
4 SA SA K26 22. POUR IN PLACE CONCRETE STEPS WITH MASONRY
13'-6"
CMA
3'-6"
A-400a K23
L1
10'-3 1/2"
5'-8" 4" 5'-2" 4" 43'-6" 4"6" 9'-8" 4" 7'-4" 23. FOOTINGS TO REST ON NATURAL UNDISTURBED SOIL
K26
STRENGTH OF 75 KPa (TYPICAL)
4"
4"
4"
54'-11"
53'-4"
K32
ENG. ROOF TRUSSES

R
DN
6'-11"
18
14'-6"
FURNACE
K11 W D
DN
18
R
4" 1'-8" 4"
18'-0"
K11 K26
K10 K26
8'-0"
7'-4"
7'-4"
7'-4"
G.T. BY ROOF
MANUF.
K11
K10
2
4"
4'-0" 6'-5" 8'-2" 6'-5" 8'-10" LAUNDRY K23
L1
ENG. ROOF TRUSSES K11 1. ALL STRUCTURAL STEEL SHALL CONFORM TO C.S.A. COPYRIGHT KDI © 2023
K11 THESE DRAWINGS ARE NOW AND DO
2
F.D.
G40.21-92 WITH A MINUMUM YEILD STRENGTH OF 350
MPa. REMAIN THE SOLE PROPERTY OF KHALSA
5'-2"
2 3A DESIGN USE OF THESE PLANS OR ANY
4"
4"
4"
PRAYER ROOM
8'-4"
8'-4"
8'-10" 9'-8" 4" 17'-10" 2. STEEL STEEL DETAILING AND CONNECTION TO
EQ
2
L1
SA
SA CONFORM TO C.S.A. CAN-3S16.1-94
4'-2"
4'-2"
4'-2"
17'-0"
CMA SA
L1
2
EQ
6'-8"
3. ALL WEDLING SHALL BE IN CONFORMANCE WITH PROSECUTION UNDER LAW
2 C.S.A. W59-M1989 AND TO THE REQUIREMENTS OF
4"
4"
4"
ENG. ROOF TRUSSES
4" 3'-6" 4" 3'-6" 4"
4"
SA
ENG. ROOF TRUSSES
K11 ARCHITECT SEAL:

2'-6"
6'-4"
3A
3A
26'-0 1/2"
TW TALL WALL DETAIL
19'-6"
19'-5"
2'-6" 10'-0" 2'-6" 2'-0" 17'-0" 2'-0"

BEDROOM 3 BEDROOM 4
05 - 02 - 2024
18'-1"
4"
1 WALL HEIGHT LESS THAN 22'-0"
10'-4"
16'-4"
14'-0"
9'-0"
A-400a
HEIGHT WD STUDS 3 ROW OF SOLID
3'-11 1/2" BLOCKING C/W 3/4" EXT. GRADE PLYWOOD
T&G SHEATHING, (3)2x6 FULL HEIGHT WOOD
8'-4"
2'-6" 8'-10" 2'-6" COLUMNS, MECHANICALLY FASTENED SILLS,
COLUMNS & TOP/BOTTOM PL STUDS &
11'-4"
15'-0" 6" 21'-0" 6" 14'-4" 4" 7'-4" 4" 13'-10" HEADER W/ SIMPSON STRONG TIE (A-23 Project number 24003
2'-6"
2'-6"
3A CLIP) AT EACH SIDE
3'-6"
3'-6"
K26
Date 05/02/2024
SB
SB
SB
SB
SB
SB
SB
Drawn by ASB
11" 7" 11" 7" 11"
11" 1'-1" 11" 11"

LVL 7 WALL HEIGHT GREATER THAN 22'-0"
1"
LVL 5 LVL 5
SB
SB
LVL 4 (DRP.) LVL 4 (DRP.)
KDI
1'-0"
1'-6"
L1
SB
SB
L1 FULL HEIGHT WD STUDS 3 ROW OF SOLID Scale As indicated
2'-0"
1'-6"
K46
SB
SB
K46
T&G SHEATHING REVISIONS
LVL 4
LVL 4 (+CURVED L9)

LVL 4

G.T. BY ROOF
MANUF.
LEGEND
ENG. ROOF TRUSSES
3'-11 1/2"
1
5" SS.
3.1. WOOD LINTELS AND BUILT-UP WOOD

x5 C
H
" x OL
O "

C /8
3/ .
S. "x3
L.
8"

HS "x5
5
LVL 4 (DRP.) 2"x8" SPRUCE #2 2"x10" SPRUCE #2 2"x12" SPRUCE #2

L1 2/2"x8" (2/38x184) L3 2/2"x10" (2/38x235) L5 2/2"x12" (2/38x286)
B1 3/2"x8" (3/38x184) B3 3/2"x10" (3/38x235) B5 3/2"x12" (3/38x286)
B2 4/2"x8" (4/38x184) B4 4/2"x10" (4/38x235) B6 4/2"x12" (4/38x286)
B7 5/2"x8" (5/38x184) B8 5/2"x10" (5/38x235) B9 5/2"x12" (5/38x286)
ENGINEERED LUMBER SCHEDULE 2.0E-3300 BY GLOBAL LVL OR EQUAL
1 3/4" x 9 1/2" LVL 1 3/4" x 11 7/8" LVL 1 3/4" x 14" LVL
11" 14'-7" 11" 4'-1" 11" 11'-0" 11" 4'-1" 11" 21'-0" 11" 10'-1" 11" 2'-10" 11" LVL2 1-1 3/4"x9 1/2" LVL3 1-1 3/4"x11 7/8" LVL10 1-1 3/4"x14"
LVL4 2-1 3/4"x9 1/2" LVL6 2-1 3/4"x11 7/8" LVL11 2-1 3/4"x14"
7'-9" 7'-9" 2'-6" 2'-6" 6'-5" 6'-5" 2'-6" 2'-6" 8'-3" 9'-10" 2'-11" 5'-11 1/2" 5'-11 1/2"
LVL5 3-1 3/4"x9 1/2" LVL7 3-1 3/4"x11 7/8" LVL12 3-1 3/4"x14"
15'-6" 5'-0" 12'-10" 5'-0" 21'-0" 11'-11" 3'-9" LVL8 4-1 3/4"x9 1/2" LVL9 4-1 3/4"x11 7/8" LVL13 4-1 3/4"x14"
LVL14 1-1 3/4"x7 1/4" LVL15 2-1 3/4"x7 1/4" LVL16 3-1 3/4"x7 1/4"
75'-0" STEEL LINTELS SUPPORTING MASONRY VENEER
CODE SIZE
BRICK STONE
SECOND FLOOR
L7
L8
3 1/2" x 3 1/2" x 1/4" (89 x 89 x 6.4)
4" x 3 1/2" x 1/4" (102 x 89 x 6.4)
8'-1" (2.47m)
8'-9" (2.66m)
7'-6" (2.30m)
8'-1" (2.48m) PLAN
L9 4 7/8" x 3 1/2" x 5/16" (127 x 89 x 7.9) 10'-10" (3.31m) 10'-1" (3.03m)
SECOND FLOOR L10 4 7/8" x 3 1/2" x 3/8" (127 x 89 x 11) 11'-5" (3.48m) 10'-7" (3.24m)
3285 sq ft L11 5 7/8" x 3 1/2" x 3/8" (152 x 89 x 11) 12'-6" (3.82m) 11'-7" (3.54m)
A-103
GROSS FLOOR AREA 4590 sq ft L12 7 1/8" x 4" x 3/8" (178 x 102 x 11) 14'-1" (4.30m) 13'-1" (3.99m)
DEDUCT OPEN AREAS 1305 sq ft
NET AREA 3285 sq ft
2-SECOND FLOOR
3/16" = 1'-0"
ON
PROJECT NAME
LEGEND
NEW WALL CMA CO ALARM
13948 Mississauga
LOADBEARING
Road, Caledon ON
WALL SA SMOKE ALARM
PROJECT ADDRESS
X WALL TYPE INTERIOR FIRE
BLOCKED
WALLS 13948 Mississauga Road, Caledon
DENOTES WELDED ON
CONNECTION STEEL
CONNECTION
CLIENT
GENERAL ROOF PLAN NOTES
2 1
A-400b A-400b 1. THIS DRAWING IS INTENDED FOR REFERENCE ONLY. HARVINDER D.
CONTRACTOR TO COORDINATE AND USE DRAWINGS,
SPECIFICATIONS AND DETAILS PROVIDED BY THE ROOF RESIDENCE
MANUFACTURER.
2. REFER TO ROOF TRUSS MANUFACTURER'S DRAWINGS
FOR LAYOUT, SPACING, INSTALLATION, DETAILS AND ARCHITECT
HANGER SIZES.
1'-6"
3. MAXIMUM SUPPORTED TRUSS LENGTH FOR LINTELS
SHALL BE 9.8m (32'-2"). SEE OBC PART 9 TABLE A-15
KHALSA DESIGN INC.
FOOTNOTE 6. WHERE DESIGNED TRUSS LENGTH EXCEEDS
1'-8"
32'-2" LINTELS SHALL BE SIZES BY A PROFESSIONAL
ENGINEER.
4. INSTALL POTLIGHTS AT 24" O.C.. COORDINATE w/
OWNER
5. ALL SOFFITS TO BE VENTED AT ALL SLOPED ROOFS.
SOFFIT FINISH TO BE SELECTED AND APPROVED BY THE
ARCHITECT/DESIGNER AND/OR OWNER.
8:12
12'-1"
6. INSTALL ALUMINUM FASCIA AND GUTTERS AS PER
4.5:12
ELEVATIONS
7. ALL DOWNSPOUTS TO BE PROVIDED WITH PRECAST
CONC. SPLASH PAD AT GRADE.
8. PROVIDE ICE & WATERSHEILD FOR ALL ROOFS.
9. PROVIDE VALLEY FLASHING AT ALL ROOF
INTERSECTIONS WHERE A VALLEY. SEE ELEVATIONS.
1'-6"
10. ALL ROOFS TO BE FINISHED WITH 25 YEAR ASHPHALT
SHINGLES UNLESS NOTED OTHERWISE ON ELEVATIONS.
11. ALL ROOF ELEMENTS COLORS TO BE SELECTED AND
APPROVED BY THE OWNER.
12. SEE MECHANICAL DRAWINGS FOR ALL MECHANICAL
PIPES, VENTS, SHAFT, ETC. THAT PENTETRATE THE ROOF. BRAMPTON, ON
CONTRACTOR TO FLASH AND SEAL ALL PENETRATIONS AS
PER SPECIFICATIONS AND DETAILS.
4.5:12
13. ALL ROOF OVERHANGS TO BE 18" [0.45m] UNLESS TELEPHONE: 647-468-2940
6:12 6:12 NOTED OTHERWISE
CONSULTANTS:
STRUCUTRAL SEAL:
8:12
8:12
6:12
FIRE
1'-6" BLOCKING 1'-6"
IN WALL AT
ATTIC
4
A-400a
FURNACE
W D
FIRE BLOCK WAL AS
PER OBC 9.10.16
PROVIDE 2x4
FRAMING w/ 1/2" GB.
BOTH SIDES
4.5:12
F.D. THESE DRAWINGS ARE NOW AND DO
RT1
ARCHITECT SEAL:
1 05 - 02 - 2024
A-400a
4.5:12
8:12 8:12
1'-3" Project number 24003

1'-3" Date 05/02/2024
Drawn by ASB
Checked by KDI
Scale As indicated
REVISIONS
7'-11"
12:12
6'-5"
1
1'-6"
1'-6"
ROOF PLAN
1
3-T/O PLATE
A-104
3/16" = 1'-0" ON
PROJECT NAME
13948 Mississauga
Road, Caledon ON
PROJECT ADDRESS

ON
12
12
8
8
CLIENT
7'-2"
MID-POINT OF ROOF
HARVINDER D.
2'-8"
2'-5"
1'-6"
2'-6"
RESIDENCE
4'-0"
1'-1" 1'-7"
2'-8"
2'-8"
1'-1"
1'-0"
1'-0"
1'-0"
3-T/O PLATE ARCHITECT
292.22 m
1'-7"
1'-6"
4'-11" 11'-0" 4'-9"
KHALSA DESIGN INC.
2'-0"
2'-0"
2'-0"
4'-0"
1'-4"
2'-6"
1'-4"
1'-4"
R
24"x72"
7'
-61
96"x60"
96"x60"
96"x60"
[3.07m]
/2"
10'-1"
7'-0"
6'-0"
12'-0"
5'-0"
5'-0"
5'-0"
8'-0"
18'-6"
1'-6"
1'-6"
1'-6"
2-SECOND FLOOR
289.15 m
22'-8"
2'-7"
33'-11 1/2"
[10.35m]
1'-0"
96"x24" 96"x24" 24"x24" 96"x24"
96"x72"
96"x72"
24"x72"
[3.68m]
12'-1"
8'-0"
8'-0"
96"x72"
9'-0"
BRAMPTON, ON
4'-2"
1'-6"
1'-6"
1-FIRST FLOOR
TELEPHONE: 647-468-2940
6"
285.47 m
3'-6"
72"x36"
72"x36"
72"x36"
K10
24"x36"
CONSULTANTS:
[3.40m]
284.30 m
11'-2"
K42 K44 K42 K44 K42 K44
283.95 m MEM ENGINEERING INC.
283.80 m
GARAGE
283.40 m
283.60 m STRUCUTRAL SEAL:
AVERAGE 283.60 m
GRADE AVERAGE
GRADE
0-TOP OF SLAB
282.06 m
PROPOSED - FRONT ELEVATION

1
3/16" = 1'-0"

12
12 12
8
6 8 SHALL RESULT IN THE FULLEST EXTENT OF
ARCHITECT SEAL:
3-T/O PLATE
292.22 m
1'-3"
2'-1"
2'-1"
05 - 02 - 2024
144"x72"
144"x72"
96"x72"
30"x72"
30"x72"
10'-1"
6'-0"
6'-0"
8'-10"
36"x96" 144"x96"
11'-0"
K11
05/02/2024
144"x60"
Date
2'-0"
2-SECOND FLOOR Drawn by ASB
5'-0"
289.15 m
Checked by KDI
3'-8"
Scale 3/16" = 1'-0"

72"x18" 40"x18"
REVISIONS
1'-1"
144"x18"
112"x24" 112"x24"
2'-0"
72"x52"
144"x96"
12'-1"
1
3'-0"
7'-9"
144"x96" 36"x96"
K11 K11
1-FIRST FLOOR
285.47 m
10'-2"
9'x10' 9'x10'
K11
6'-9"
144"x72"
8'-5"
K10
11'-2"
6'-0"
GARAGE
8'-0"
8'-0"
64"x96" 144"x96" 283.40 m
FRONT & REAR
4'-5"
282.90 m
2'-9"
2'-0"
0-TOP OF SLAB
282.06 m
ELEVATION
K30
PROPOSED - REAR ELEVATION

A-301
2
3/16" = 1'-0" ON
PROJECT NAME
NOTE: WINDOW SUMMARY
REFER TO FRONT PER O.B.C. TABLE 9.10.15.4
4
ELEVATION FOR
GENERAL NOTES LEFT SIDE ELEVATION 13948 Mississauga
A-400a
Road, Caledon ON
QUANT.
WINDOW/
HEIGHT
WIDTH
DOOR FRAME
SIZE (SF) PROJECT ADDRESS
1 60" 18" 5.44 SF
1 56" 24" 7.22 SF
1 32" 60" 10.89 SF
12 1 96" 24" 12.78 SF
12
1 60" 52" 18.67 SF ON
12 1 56" 60" 20.22 SF
12 1 96" 72" 43.44 SF
4.5
118.67 SF
8
SPATIAL CALCULATION CLIENT
12 EXPOSING BUILDING 1630.00 S.F.
FACE AREA 151.43 S.M.
4.5 1630.00 S.F.
PORTION WALL AREA
151.43 S.M.
LIMITING DISTANCE 1.5 m
MAX. % OPENINGS
OPENINGS ALLOWED
OPENINGS PROVIDED
8%
130.40 SF
118.67 SF
HARVINDER D.
[0.81m]
RESIDENCE
2'-8"
ADDITIONAL NOTES
3-T/O PLATE GLAZED AREA CALCULATED W/ FRAME SIZE
292.22 m MINUS 2" AROUND ENTIRE PERIMETER
ARCHITECT
32"x60"
56"x60"
KHALSA DESIGN INC.
[3.07m]
10'-1"
2-SECOND FLOOR
289.15 m
60"x18" 96"x24"
60"x52"
96"x72"
[3.68m]
12'-1"
1-FIRST FLOOR BRAMPTON, ON
285.47 m
TELEPHONE: 647-468-2940
[2.06m]
6'-9"
56"x24"
[3.40m]
CONSULTANTS:
11'-2"
GARAGE
283.40 m
[1.34m]
4'-5"
STRUCUTRAL SEAL:
0-TOP OF SLAB
282.06 m
PROPOSED - LEFT SIDE ELEVATION

2
3/16" = 1'-0"
NOTE: WINDOW SUMMARY

REFER TO FRONT PER O.B.C. TABLE 9.10.15.4
4
ELEVATION FOR RIGHT SIDE ELEVATION A -
A-400a GENERAL NOTES STANDARD PLAN
QUANITY
WINDOW/
HEIGHT
WIDTH
DOOR FRAME
SIZE (SF)
1 56" 24" 7.22 SF COPYRIGHT KDI © 2023
1 56" 24" 7.22 SF THESE DRAWINGS ARE NOW AND DO
1 56" 24" 7.22 SF
12 REMAIN THE SOLE PROPERTY OF KHALSA
1 24" 60" 7.78 SF
12 1 24" 60" 7.78 SF
12 1 24" 60" 7.78 SF FORM OF REPRODUCTION OF THIS DESIGN
4.5 12
1 24" 72" 9.44 SF IN WHOLE OR IN PART WITHOUT EXPRESS
12 1 24" 72" 9.44 SF WRITTEN CONSENT IS PROHIBITED AND
4.5
1 40" 96" 11.46 SF
8
1 46" 96" 14.21 SF
1 56" 60" 20.22 SF PROSECUTION UNDER LAW
1 56" 72" 24.56 SF
1 56" 72" 24.56 SF
1 56" 72" 24.56 SF ARCHITECT SEAL:
183.44 SF
SPATIAL CALCULATION
3-T/O PLATE EXPOSING BUILDING 1849.90 S.F.
FACE AREA 171.86 S.M.
292.22 m 1849.90 S.F.
PORTION WALL AREA
2'-3"
2'-3"
171.86 S.M.
LIMITING DISTANCE 6.0 m
MAX. % OPENINGS
OPENINGS ALLOWED
19 %
351.48 SF
05 - 02 - 2024
24"x60"
24"x60"
24"x60"
56"x60"
24"x72"
24"x72"
OPENINGS PROVIDED 183.44 SF
ADDITIONAL NOTES
[3.07m]
5'-0"
10'-1"
GLAZED AREA CALCULATED W/ FRAME SIZE
6'-0"
6'-0"
MINUS 2" AROUND ENTIRE PERIMETER
24003
2'-10"
Project number
1'-10"
1'-10"
2-SECOND FLOOR Date 05/02/2024
289.15 m Drawn by ASB
Checked by KDI
Scale 3/16" = 1'-0"
5'-10"
REVISIONS
[3.68m]
12'-1"
56"x24" 56"x24" 56"x24"
1
42"x96"
56"x72"
56"x72"
56"x72"
8'-0"
1-FIRST FLOOR
K11
8"
285.47 m
K10 1-MUDROOM
4'-10"
284.86 m
4'-2"
36"x96"
5'-0"
283.99 m
[3.40m]
11'-2"
GARAGE
283.40 m
SIDE
0-TOP OF SLAB
282.06 m ELEVATIONS
1
PROPOSED - RIGHT SIDE ELEVATION
A-302
3/16" = 1'-0"
ON
PROJECT NAME
13948 Mississauga
Road, Caledon ON
PROJECT ADDRESS

ON
CLIENT
RT1
HARVINDER D.
RESIDENCE
3'-6"
1'-7 1/2"
3-T/O PLATE
292.22 m
1'-7 1/2"
1'-6" K9
ARCHITECT
KHALSA DESIGN INC.
10'-1"
BEDROOM 3 BEDROOM 4
2-SECOND FLOOR
289.15 m
K11 K11
12'-1"
K10 K10
FOYER GUEST
LIVING STUDY
BEDROOM

285.47 m
TELEPHONE: 647-468-2940
K11
CONSULTANTS:
11'-2"
GARAGE STRUCTURAL ENGINEER:
K34A 283.40 m
K5C K13
K12
K6
STRUCUTRAL SEAL:
K10
0-TOP OF SLAB
282.06 m
K30
BUILDING SECTION 1
1
3/16" = 1'-0"

RT1
ARCHITECT SEAL:
1'-7 1/2"
1'-7 1/2"
1'-0"
3-T/O PLATE
K9
292.22 m
05 - 02 - 2024
10'-1"
HER W.I.C.
ENS. 2 W.I.C.
K11
2-SECOND FLOOR
Date 05/02/2024
289.15 m Drawn by ASB
Checked by KDI
Scale 3/16" = 1'-0"
REVISIONS
12'-1"
4 CAR 1
PANTRY GARAGE
W.I.C.
K11 1-FIRST FLOOR

K10 285.47 m
11'-2"
K18
GARAGE
283.40 m
K5C
K12
K13
K34A
K6 BUILDING
WT5
K7
0-TOP OF SLAB
282.06 m SECTIONS
A-400a
K30
BUILDING SECTION II 13948 Mississauga Road, Caledon

4
3/16" = 1'-0" ON
PROJECT NAME
13948 Mississauga
Road, Caledon ON
PROJECT ADDRESS

ON
CLIENT
RT1
2'-2"
HARVINDER D.
10"
3'-6"
RESIDENCE
2'-8"
2'-8"
2'-8"
TW
4'-0"
3-T/O PLATE
292.22 m
1'-4"
K9 17'-0" 11'-4"
1'-1 1/2"
TW
ARCHITECT
KHALSA DESIGN INC.
10'-1"
K11
3'-6"
K11 K11
17'-2"
25'-4"
2-SECOND FLOOR
2'-5 1/2"
6"
289.15 m
22'-2"
22'-2"
20'-10"
12'-1"
K10
10'-6"
FAMILY ROOM
FOYER
4'-2"
K11 K11
6"
6"
285.47 m
K31
K11 TELEPHONE: 647-468-2940
K5C
K13
K12
11'-2"
K34A
K10
WT5
CONSULTANTS:
COLD CELLAR
GARAGE
282.91 m 283.40 m
STRUCUTRAL SEAL:
K7 K6
0-TOP OF SLAB
282.06 m
2'-0"
2'-0"
K30
BUILDING SECTION III

2
3/16" = 1'-0"

12
12
12
4.5
RT1 ARCHITECT SEAL:
1'-6" 3-T/O PLATE

292.22 m
05 - 02 - 2024
10"
K9
1'-1 1/2"
1'-6"
10'-1"
10'-1"
PRIMARY PRIMARY
BEDROOM 4 W.I.C.
ENSUITE BEDROOM

Date 05/02/2024
Drawn by ASB
2-SECOND FLOOR
289.15 m Checked by KDI
Scale 3/16" = 1'-0"
REVISIONS
12'-1"
GUEST
MUDROOM
BEDROOM
4 CAR
GARAGE
17'-9 1/2"
1-FIRST FLOOR
285.47 m
K11
K10
11'-2"
K5C
K34A K18
K12
K13 GARAGE
WT5
283.40 m
BUILDING
K6 K7
0-TOP OF SLAB
SECTIONS
282.06 m
K30
BUILDING SECTION IV
A-400b
1
3/16" = 1'-0" ON
PROJECT NAME
LIMITING DISTANCE GREATER THAN 3'-11" (1.20m)
3 1/2" MASONRY VENEER TIED TO FRAMING MEMBERS WITH
7/8"x7"x.03" GALV. METAL TIES @ 16" O.C. AND 24" VERTICAL, 1" AIR MORTAR FILLED SPACE
SPACE, APPROVED AIR/WATER BARRIER ON 3/8" EXTERIOR TYPE
SHEATHING ON 2"x6" SPRUCE STUDS @ 16" O.C., INSULATION W/
BETWEEN FOUNDATION WALL
AND MASONRY VENEER
13948 Mississauga
REQUIRED WALLS ABOVE GRADE R-VALUE, APPROVED 6 MIL POLY
Road, Caledon ON
1'-6" MAX.
VAPOUR BARRIER, 1/2" GYPSUM WALLBOARD INTERIOR FINISH.
GROUND
NOTE: POURED CONC. FOOTING ON NATURAL UNDISTURBED SOIL OF FLOOR
75kPa OR COMPACTED ENGINEERED FILL WITH MIN. BEARING PROJECT ADDRESS
CAPACITY OF 150kPa. FOOTING SIZE SHOWN FOR 16'-0" (4.9m)
STUCCO FINISH COAT MAXIMUM JOIST SPAN ONLY. JOIST SPAN EXCEEDING 16'-0" (4.9m) 12" (TYP.) 25 MPa POURED CONC. 0' - 8" MIN.
SHALL BE ENGINEERED. IF SOIL BEARING DOES NOT MEET MINIMUM FOUNDATION WALLS
STUCCO PRIMER ON STUCCO PREP CAPACITY, ENGINEERED FOOTINGS ARE REQUIRED. ACTUAL SOIL 13948 Mississauga Road, Caledon
BEARING CAPACITY TO BE VERIFIED WITH SOIL ENGINEERING REPORT.
COAT W/ EMBEDDED AND WRAPPED
REINFORCING MESH 1' - 0"
ON
1 1/2" RIGID INSULATION BASE FLASHING CONFORMING TO TABLE 9.20.13.1 TO EXTEND 3/16"
BEYOND OUTER FACE OF FOUNDATION WALL, TIED TO EXT. SHEATHING
DENSE GLASS GOLD WALL SHEATHING UNDER AIR/WATER BARRIER, PROVIDE 6" MINIMUM LAP JOINT.
WEEP HOLES @ 32" O.C. AT BASE FLASHING AND OVER ALL OPENINGS. CLIENT
WATER RESISTANT MOISTURE BARRIER PROVIDE P.V.C. BRICK VENTILATOR @ ALL WEEP HOLE LOCATIONS. GROUND FLOOR
2"x6" BASE PLATE
PROVIDE CONTINUOUS APPROVED AIR/WATER BARRIER AROUND
DRAINAGE CHANNEL ADHESIVE HEADERS, UNDER BOTTOM PLATE AND UP STUD WALL BEHIND GYPSUM
MIN. 1 1/2" THICK HEADER AS PER JOIST DEPTH - REFER TO ENG.
DRAINAGE TRACK
WALLBOARD, PROVIDE CAULKING AT JOINTS, AIR/WATER BARRIER SHALL
FLOOR JOIST MANUF. FOR RIMBOARD OR HEADER SIZE.
HARVINDER D.
6" MIN
EXTEND UNDER SILL PLATE TO OUTSIDE FACE OF INSULATION UNDER 6 MIL
POLY VAPOUR BARRIER.
SEALANT W/ CLOSED CELL TYPICAL FLOOR CONSTRUCTION RESIDENCE
1'-2
MA
FINISHED GRADE
X.
"
BACKER ROD
MINIMUM 2"x4" SILL PLATE, TIED TO TOP OF POURED CONC. FND. WALL
FLASHING
WITH 8" LONGx1/2"∅ ANCHOR BOLTS C/W NUT AND WASHER WITH 2
PROVIDE MASONRY PARGING FROM TOP OF 4 1/2" 1/2" HOOK. ANCHOR BOLTS TO BE SPACED NOT MORE THAN 7'-10" O.C.
FOUNDATION WALL TO 2" BELOW FINISHED GRADE AND EMBEDDED NOT LESS THAN 4" INTO CONC. PROVIDE SILL GASKET ARCHITECT
BETWEEN PLATE AND FOUNDATION WALL. PROVIDE NON-SHRINK
GROUT TO LEVEL PLATE.
INSULATION BLANKET OR BATTS W/ REQUIRED BASEMENT WALL R-
VALUE, 6 MIL POLYETHYLENE VAPOUR BARRIER DAMPPROOF WITH
KHALSA DESIGN INC.
AIR/WATER BARRIER BETWEEN THE FOUNDATION WALL AND
12" 25MPa POURED CONC. FOUNDATION WALL INSULATION UP TO GRADE LEVEL. TERMINATE BLANKETS ABOVE SLAB
CONTINOUS INTERIOR SPACE ON 30"x8" DEEP POURED CONC. FOOTING w/
15M @ 16" HORIZONTAL AND 15M @ 16" O.C.
AS REQUIRED BY O.B.C. OR ENERGY DESIGN CONSULTANT
PRECAST CONC. OR TAPE AND SEAL BLANKETS AT ALL JOINTS
VERTICAL BARS.
STONE SLOPED SILL SECURE METAL BLANKET TIE TO FOUNDATION
FOOTINGS TO BEAR ON UNDISTRUBED SOIL w/
W/ DRIP EDGE WALL AS PER MANUF. INSTRUCTIONS
GYPSUM WALLBAORD 2-15M CONT. BAR REBAR (TYP.)
VAPOUR BARRIER
WOOD STUD WALL
UNFINISHED BASEMENT
BATT INSULATION 1/2" IMPERVIOUS BOARD FOR BOND BREAK
(THICKNESS DEPENDANT ON REQ'D R
4" MIN. 25 MPa CONC. SLAB ON 4" COARSE CLEAN GRANULAR FILL
VALUE)
OR 20 MPa CONC. WITH DAMPPROOFING BELOW SLAB.
EXTERIOR SHEATHING
AIR BARRIER MEMBRANE
MIN. .25 MM AIR SPACE
CALCIUM SILICATE BUILDING STONE FOUNDATION WALLS SHALL NOT EXCEED 9'-10" (3.0m) IN UNSUPPORTED
HEIGHT UNLESS OTHERWISE NOTED. (9.15.4.2.1). POURED CONC. FDTN. WALL
WITH BITUMINOUS DAMPPROOFING AND DRAINAGE LAYER. REFER TO CHART
FOR MAXIMUM UNSUPPORTED HEIGHT AND EARTH RETENTION FROM
WEEP HOLES @600 BASEMENT SLAB TO FINISHED GRADE, ON CONTINUOUS KEYED CONC. FTG..
CORRUGATED STRIP TIE MM O/C BRACE FOUNDATION WALL PRIOR TO BACKFILLING. ALL FOOTINGS SHALL CONTINUOUS KEY IN CONCRETE
SCREW INTO WOOD (WHEN @ WINDOW) REST ON NATURAL UNDISTURBED SOIL OR COMPACTED ENGINEERED FILL.
STUD
4" ∅ WEEPING TILE, 6" CRUSHED STONE COVER POURED CONC. FOOTINGS. SEE 'MINIMUM STRIP
OVER AND AROUND WEEPING TILES. FOOTING SIZES FOR EXTERIOR WALLS' CHART
FLOOR & ROOF CONSTRUCTION
REFER TO FLOOR & ROOF TRUSS MANUFACTURERS
DRAWINGS FOR SPECIFICATION, DETAILS, LAYOUT, SPACING,
INSTALLATION, HANDLING AND HANGER SIZES.
TYPICAL STUCCO TO MASONRY TRANSITION W/ SINGLE

PRE-FINISHED ALUMINUM GUARD BRAMPTON, ON
BEYOND FLASHING, DETAIL MASONRY VENEER, 2"x6" STUDS, REVERSE CONC. CHECK
4 3
3" = 1'-0" 1/2" = 1'-0"
TELEPHONE: 647-468-2940
3"x2" PREFINSIHED ALUMINUM TOP
RAILS MECHANICALLY FASTENED TO
MAIN POSTS (TYP)
LIMITING DISTANCE LESS THAN 3'-11" (1.20m) CONSULTANTS:
1"x1" PREFINSIHED ALUMINUM PICKETS FIRE RATINGS: (OBC REFERENCE - SB-2.3)
COMPONENT FIRE RATING CODE REFERENCE
MECHANICAL FASTENED TO TOP AND
BOTTOM RAILS (SEE MANUF'S SPEC'S) GABLE END: 1/2" (12.7mm) TYPE X O.B.C. SB-2.3.4.(2) GABLE END: STRUCTURAL ENGINEER:
TYPICAL EXTERIOR WALL 25 min.
(TYP)
CONSTRUCTION STUCCO CLADDING CONFORMING TO O.B.C. SECTION 9.28. AND GYPSUM WALL BOARD (TABLE 2.3.4.A.) 3 1/2" MASONRY VENEER TIED TO FRAMING MEMBERS WITH
7/8"x7"x.03" GALV. METAL TIES @ 16" O.C. AND 24" VERTICAL, 1"
APPLIED PER MANUFACTURERS SPECIFICATIONS OVER 1" MINIMUM 12 WOOD STUDS @ 406mm O.B.C. SB-2.3.4.(3)
20 min. AIR SPACE, APPROVED AIR/WATER BARRIER ON 3/8" EXTERIOR
3'-0" MIN.
VARIES
EXTERIOR RIGID INSULATION BOARD ON APPROVED AIR/WATER BARRIER O.C. MAXIMUM (TABLE 2.3.4.C.)
2"x4" PT. DECKING W 1/4" GAPS TYPE SHEATHING ON 2"x4" SPRUCE STUDS @ 16" O.C. 12
ON 1/2" EXTERIOR TYPE SHEATHING ON 2"x4" SPRUCE STUDS @ 16" O.C. STRUCUTRAL SEAL:
VARIES
TOTAL FIRE RATING 45 min. O.B.C. SB-2.3.4.(1)
3'-6" MIN
3"X3" PRE-MANUF'D ALUMINUM MAIN LAID FLAT PARALLEL TO JOISTS ON

2"x4" PT. SLEEPERS @ 12" O.C. LAID No. 210 ASPHALT SHINGLES, 3/8" EXTERIOR TYPE SHEATHING
POSTS WITH BASE PLATES @ 4'-0" 0.C
FLAT PERP TO JOISTS ON A TWO WITH "H" CLIPS. APPROVED WOOD TRUSSES @ 24" O.C. MAX.
MAX. MECHANICALLY FASTENED TO No. 210 ASPHALT SHINGLES, 3/8" EXTERIOR TYPE SHEATHING
PLY BITUMOUS (OR ONE PLY APPROVED EAVES PROTECTION TO EXTEND 3'-0" FROM EDGE
TOP OF 2-2"X8"TO P PLATES WITH 4-2.5" WITH "H" CLIPS. APPROVED WOOD TRUSSES @ 24" O.C. MAX.
RUBBER) MEMBRANE ADHERED TO OF ROOF AND MIN. 12" BEYOND INNER FACE OF EXTERIOR
LONG WOOD SCREWS COVER SCREWS APPROVED EAVES PROTECTION TO EXTEND 3'-0" FROM EDGE
EXT. TYPE 5/8" WALL, 2"x4" TRUSS BRACING 6'-0" O.C. AT BOTTOM CHORD.
WITH PRE-MANUF'D ALUMINUM OF ROOF AND MIN. 12" BEYOND INNER FACE OF EXTERIOR
BASE PLATES (SEE MANUF'S SPEC'S) (TYP) EXT. SHEATHING ON 2"x2" SLEEPERS
WALL, 2"x4" TRUSS BRACING 6'-0" O.C. AT BOTTOM CHORD.
SECOND(SLOPED TO SCUPPER) ON 2"x8" PRE-MANUFACTURED ALUM. FLASHING
PROVIDE ADEQUATE SPACE FOR INSULATION DIRECTLY ABOVE THE
1"x1" PREFINSIHED ALUMINUM SPR. #2 FLOOR JOISTS @ 16" O.C.
BOTTOM RAILS MECHANICAL FLOOR W/ ALUM. SOFFIT ON U/S. INNER SURFACE OF EXTERIOR WALLS. INSULATION VALUE SHALL
NOT BE LESS THAN R20 (3.52 RSI) AS PER O.B.C. 2.1.1.7.(1)
FASTENED TO MAIN POSTS AIR BAFFLE TIED TO UNDERSIDE OF ROOF PROVIDE ADEQUATE SPACE FOR INSULATION DIRECTLY ABOVE
RUBBERIZED MEMBRANE UNDER SHEATHING WITH 2 1/2" MIN. VOID AREA PRE-MANUFACTURED ALUM. FLASHING THE INNER SURFACE OF EXTERIOR WALLS. INSULATION VALUE
PREFINISHED METAL CAP DOOR SILL BY METAL FLASHING
2"x6" SPRUCE FASCIA BOARD AIR BAFFLE TIED TO UNDERSIDE OF ROOF SHEATHING SHALL NOT BE LESS THAN R20 (3.52 RSI) AS PER O.B.C. 2.1.1.7.(1)
FLASHING
PRECAST CONC. SILL WITH 2 1/2" MIN. VOID AREA
BUILT UP WOOD PARAPET TO
PRE-FINISHED ALUMINUM FASCIA, RAINWATER LEADER AND VENTED 2"x6" SPRUCE FASCIA BOARD
+/-7"
SUPPORT RAILING
4 "
2
1_
GALV. PREFINISHED METAL FLASHING SOFFIT TIED TO BRICK VENEER, PROVIDE ATTIC VENTILATION - 1/300 1/2" GYPSUM CEILING BOARD INTERIOR FINISH ON 6 MIL POLY
24 GA PREFINISHED METAL FLASHING OF INSULATED CEILING AREA WITH 50% AT THE EAVES PRE-FINISHED ALUMINUM FASCIA, RAINWATER LEADER AND VENTED
VAPOUR BARRIER ON BOTTOM CHORD OF ROOF TRUSSES, SOFFIT TIED TO BRICK VENEER, PROVIDE ATTIC VENTILATION - 1/300
W/ HEMMED EDGE. EDGE TO BE VARIES
CANT STRIP PREFINISHED FRIEZE BOARD, VARIES PER ELEVATION INSULATION W/ REQUIRED CEILING W/ ATTIC SPACE R-VALUE OF INSULATED CEILING AREA WITH 50% AT THE EAVES
LACED FIRMLY ON SUFACE OF DECK 1/2" GYPSUM CEILING BOARD INTERIOR FINISH ON 6 MIL POLY
MEMBRANE. FASTENERS TO HAVE LIMITING DISTANCE GREATER THAN 3'-11" (1.20m) 2-2"x6" TOP PLATE VAPOUR BARRIER ON BOTTOM CHORD OF ROOF TRUSSES,
PREFINISHED FRIEZE BOARD, VARIES PER ELEVATION
EOPRENE HEADS & TO BE FASETNED STUCCO FINISH CONFORMING TO O.B.C. SECTION 9.28. AND APPLIED VARIES INSULATION W/ REQUIRED CEILING W/ ATTIC SPACE R-VALUE
AS PER ELEVATION
THROUGH BUTYL TAPE. PER MANUFACTURERS SPECIFICATIONS OVER 1 1/2" MINIMUM SECOND FLOOR
TRIM AS PER ELEVATIONS EXTERIOR RIGID INSULATION BOARD ON APPROVED DRAINAGE MAT 2"x6" BASE PLATE 2-2"x6" TOP PLATE
ON 1/2" DENSGLASS GOLD GYPSUM BOARD ON 2"x6" SPRUCE STUDS
AS PER ELEVATION
INSULATE MIN. 12" BEYOND
FURR OUT BEAM AS REQUIRED
2"X8" JOISTS @ 12" O.C. SECURED
@ 16" O.C., INSULATION W/ REQUIRED WALLS ABOVE GRADE R-
VALUE , APPROVED 6 MIL VAPOUR BARRIER, 1/2" GYPSUM MIN. 1 1/2" THICK HEADER AS PER JOIST DEPTH - REFER TO ENG.
SECOND FLOOR
WITH METAL HANGERS TO HEADER. WALLBOARD INTERIOR FINISH. FLOOR JOIST MANUF. FOR RIMBOARD OR HEADER SIZE. LIMITING DISTANCE GREATER THAN 3'-11" (1.20m)
2"x6" BASE PLATE
SINGLE PLY "DURADEK" MEMBRANE IF REQUIRED, BLOCKING BEHIND LIMITING DISTANCE LESS THAN 3'-11" (1.20m) (45 MIN. FRR) 3 1/2" MASONRY VENEER TIED TO FRAMING MEMBERS WITH
T/G SUBFLOOR ON FLOOR JOISTS. FOR CERAMIC TILE APPLICATION
(INSTALLED PER MANUF. SPECS.) ON 3/8" HEADER SHOULD BE PLACED. METAL 7/8"x7"x.03" GALV. METAL TIES @ 16" O.C. AND 24" VERTICAL, 1" AIR MIN. 1 1/2" THICK HEADER AS PER JOIST DEPTH - REFER TO ENG.
STUCCO FINISH CONFORMING TO O.B.C. SECTION 9.28. AND APPLIED PER REFER TO O.B.C. 9.30.6.. ALL JOISTS TO BE BRIDGED WITH 2"x2"
EXT. TYPE PLYWOOD SHT'G ON 2"x2" HANGERS TO BE USED IF SPAN SPACE, APPROVED AIR/WATER BARRIER ON 3/8" EXTERIOR TYPE FLOOR JOIST MANUF. FOR RIMBOARD OR HEADER SIZE.
MANUFACTURERS SPECIFICATIONS OVER 1 1/2" MINIMUM EXTERIOR RIGID CROSS BRACING OR SOLID BLOCKING @ 6'-11" O.C. MAX. ALL
SLEEPERS (SLOPED TO SCUPPER) ON FLOOR PORCH EXCEEDS 4'-0"
INSULATION BOARD ON APPROVED DRAINAGE MAT ON 1/2" DENSGLASS JOISTS TO BE STRAPPED WITH 1"x3" @ 6'-11" O.C. UNLESS A PANEL
SHEATHING ON 2"x6" SPRUCE STUDS @ 16" O.C., INSULATION W/
T/G SUBFLOOR ON FLOOR JOISTS. FOR CERAMIC TILE APPLICATION
JOISTS W/ PREFIN. ALUM. SOFFIT ON U/S. GOLD GYPSUM BOARD ON 2"x6" SPRUCE STUDS @ 16" O.C., INSULATION REQUIRED WALLS ABOVE GRADE R-VALUE, APPROVED 6 MIL POLY THESE DRAWINGS ARE NOW AND DO
PREFINED ALUMINUM SOFFIT TYPE CEILING FINISH IS APPLIED. REFER TO ENG. FLOOR JOIST REFER TO O.B.C. 9.30.6.. ALL JOISTS TO BE BRIDGED WITH 2"x2"
W/ REQUIRED WALLS ABOVE GRADE R-VALUE CONFORMING TO VAPOUR BARRIER, 1/2" GYPSUM WALLBOARD INTERIOR FINISH.
MANUF. FOR BRACING SPECIFICATIONS.
LIMITING DISTANCE LESS THAN 3'-11" (1.20m) (45 MIN. FRR)
CROSS BRACING OR SOLID BLOCKING @ 6'-11" O.C. MAX. ALL REMAIN THE SOLE PROPERTY OF KHALSA
GROUND CAN/ULC-S702 AND HAVING A MASS OF NOT LESS THAN 1.22 kg/m2 OF JOISTS TO BE STRAPPED WITH 1"x3" @ 6'-11" O.C. UNLESS A PANEL
WALL SURFACE, 1/2" TYPE X GYPSUM WALLBOARD INTERIOR FINISH. 3 1/2" MASONRY VENEER TIED TO FRAMING MEMBERS WITH TYPE CEILING FINISH IS APPLIED. REFER TO ENG. FLOOR JOIST
FLOOR INSULATION W/ REQUIRED EXPOSED FLOOR R-VALUE IN 7/8"x7"x.03" GALV. METAL TIES @ 16" O.C. AND 24" VERTICAL, 1" AIR MANUF. FOR BRACING SPECIFICATIONS. FORM OF REPRODUCTION OF THIS DESIGN
LIMITING DISTANCE LESS THAN 23 5/8" (0.60m) HEADER SPACE SPACE, APPROVED AIR/WATER BARRIER ON3/8" EXTERIOR TYPE
CLADDING MUST BE NON-COMBUSTIBLE. SHEATHING ON 2"x6" SPRUCE STUDS @ 16" O.C., INSULATION W/ IN WHOLE OR IN PART WITHOUT EXPRESS
INSULATION W/ REQUIRED EXPOSED FLOOR R-
2"x2" @ 16" O.C. FURRING. TOP PLATE TIED TO UNDERSIDE OF CANT. JOISTS.
ONE LAYER 5/8" TYPE X GYPSUM WALLBOARD FOR REQUIRED WALLS ABOVE GRADE R-VALUE CONFORMING TO
VALUE IN HEADER SPACE
LIMITING DISTANCE LESS THAN 3'-11" (1.20m) CAN/ULC-S702 AND HAVING A MASS OF NOT LESS THAN 1.22 SHALL RESULT IN THE FULLEST EXTENT OF
VARIES
BOTTOM PLATE TIED TO 2"x6" STUD WALL. BRICK NOT TO SUPPORT FURRED WALL.
kg/m2 OF WALL SURFACE, APPROVED 6 MIL. POLY VAPOUR
TYP. BALCONY OVER UNHEATED SPACE CONTINUOUS PREFINISHED ALUMINUM DRAINAGE TRACK. LAP 2-2"x6" TOP PLATE BARRIER, 1/2" TYPE X GYPSUM WALLBOARD INTERIOR FINISH. ONE LAYER 5/8" TYPE X GYPSUM WALLBOARD PROSECUTION UNDER LAW
6 DRAINAGE MAT OVER DRAINAGE TRACK. PROVIDE CAULKING FOR LIMITING DISTANCE LESS THAN 3'-11"
3/4" = 1'-0" AND BACKERROD AT INTERSECTION WITH PRECAST CONC. SILL PROVIDE CONTINUOUS APPROVED AIR/WATER BARRIER AROUND LIMITING DISTANCE LESS THAN 3'-11" (1.20m)
FIRE RATINGS: (OBC REFERENCE - SB-2.3)
(1.20m)
HEADERS, UNDER BASE PLATES AND UP STUD WALL BEHIND GYPSUM 2-2"x6" TOP PLATE
LIMITING DISTANCE GREATER THAN 3'-11" (1.20m)
WALLBOARD, PROVIDE CAULKING AT JOINTS. COMPONENT FIRE RATING CODE REFERENCE PROVIDE CONTINUOUS APPROVED AIR/WATER BARRIER ARCHITECT SEAL:
3 1/2" MASONRY VENEER TIED TO FRAMING MEMBERS WITH 7/8"x7"x.03" 1/2" (12.7mm) TYPE X
AS PER ELEVATION
O.B.C. SB-2.3.4.(2) AROUND HEADERS, UNDER BASE PLATES AND UP STUD WALL
AS PER ELEVATION
GALV. METAL TIES @ 16" O.C. AND 24" VERTICAL, 1" AIR SPACE, APPROVED GYPSUM WALL BOARD 25 min.
WEEP HOLES @ 32" O.C. AT BASE FLASHING AND OVER ALL OPENINGS. (TABLE 2.3.4.A.) BEHIND GYPSUM WALLBOARD, PROVIDE CAULKING AT JOINTS.
AIR/WATER BARRIER ON 3/8" EXTERIOR TYPE SHEATHING ON 2"x6" SPRUCE
PROVIDE P.V.C. BRICK VENTILATOR @ ALL WEEP HOLE LOCATIONS.
STUDS @ 16" O.C., INSULATION W/ REQUIRED WALLS ABOVE GRADE R- WOOD STUDS @ 406mm O.B.C. SB-2.3.4.(3)
VALUE, APPROVED 6 MIL POLY VAPOUR BARRIER, 1/2" GYPSUM O.C. MAXIMUM
20 min.
(TABLE 2.3.4.C.) FIRST FLOOR
WALLBOARD INTERIOR FINISH. FIRST FLOOR TOTAL FIRE RATING 45 min. O.B.C. SB-2.3.4.(1) 2"x6" BASE PLATE
LIMITING DISTANCE LESS THAN 3'-11" (1.20m) (45 MIN. FRR) 2"x6" BASE PLATE MIN. 1 1/2" THICK HEADER AS PER JOIST DEPTH - REFER TO ENG.
3 1/2" MASONRY VENEER TIED TO FRAMING MEMBERS WITH 7/8"x7"x.03" FLOOR JOIST MANUF. FOR RIMBOARD OR HEADER SIZE.
05 - 02 - 2024
GALV. METAL TIES @ 16" O.C. AND 24" VERTICAL, 1" AIR SPACE, APPROVED MIN. 1 1/2" THICK HEADER AS PER JOIST DEPTH - REFER TO
AIR/WATER BARRIER ON3/8" EXTERIOR TYPE SHEATHING ON 2"x6" SPRUCE ENG. FLOOR JOIST MANUF. FOR RIMBOARD OR HEADER SIZE. PROVIDE CONTINUOUS APPROVED AIR/WATER BARRIER AROUND
STUDS @ 16" O.C., INSULATION W/ REQUIRED WALLS ABOVE GRADE R-VALUE HEADERS, UNDER BOTTOM PLATE AND UP STUD WALL BEHIND
INSULATION W/ REQUIRED EXPOSED
CONFORMING TO CAN/ULC-S702 AND HAVING A MASS OF NOT LESS THAN GYPSUM WALLBOARD, PROVIDE CAULKING AT JOINTS, AIR/WATER
FLOOR R-VALUE IN HEADER SPACE T/G SUBFLOOR ON FLOOR JOISTS. FOR CERAMIC TILE APPLICATION
1.22 kg/m2 OF WALL SURFACE, APPROVED 6 MIL. POLY VAPOUR BARRIER, BARRIER SHALL EXTEND UNDER SILL PLATE TO OUTSIDE FACE OF
REFER TO O.B.C. 9.30.6.. ALL JOISTS TO BE BRIDGED WITH 2"x2"
1/2" TYPE X GYPSUM WALLBOARD INTERIOR FINISH. T/G SUBFLOOR ON FLOOR JOISTS. FOR CERAMIC TILE INSULATION UNDER 6 MIL POLY VAPOUR BARRIER.
CROSS BRACING OR SOLID BLOCKING @ 6'-11" O.C. MAX. ALL
PROVIDE CONTINUOUS APPROVED AIR/WATER BARRIER AROUND APPLICATION REFER TO O.B.C. 9.30.6.. ALL JOISTS TO BE BRIDGED BASE FLASHING CONFORMING TO TABLE 9.20.13.1 TO EXTEND 3/16" JOISTS TO BE STRAPPED WITH 1"x3" @ 6'-11" O.C. UNLESS A PANEL
HEADERS, UNDER BOTTOM PLATE AND UP STUD WALL BEHIND GYPSUM WITH 2"x2" CROSS BRACING OR SOLID BLOCKING @ 6'-11" O.C. BEYOND OUTER FACE OF FOUNDATION WALL, TIED TO EXT. SHEATHING TYPE CEILING FINISH IS APPLIED. REFER TO ENG. FLOOR JOIST
WALLBOARD, PROVIDE CAULKING AT JOINTS, AIR/WATER BARRIER MAX. ALL JOISTS TO BE STRAPPED WITH 1"x3" @ 6'-11" O.C. UNLESS UNDER AIR/WATER BARRIER, PROVIDE 6" MINIMUM LAP JOINT. MANUF. FOR BRACING SPECIFICATIONS.
SHALL EXTEND UNDER SILL PLATE TO OUTSIDE FACE OF INSULATION A PANEL TYPE CEILING FINISH IS APPLIED. REFER TO ENG. FLOOR
UNDER 6 MIL POLY VAPOUR BARRIER. JOIST MANUF. FOR BRACING SPECIFICATIONS.
INSULATION W/ REQUIRED EXPOSED
BASE FLASHING CONFORMING TO TABLE 9.20.13.1 TO EXTEND 3/16" WEEP HOLES @ 32" O.C. AT BASE FLASHING AND OVER ALL OPENINGS. FLOOR R-VALUE IN HEADER SPACE
BEYOND OUTER FACE OF FOUNDATION WALL, TIED TO EXT. SHEATHING PROVIDE P.V.C. BRICK VENTILATOR @ ALL WEEP HOLE LOCATIONS.
UNDER AIR/WATER BARRIER, PROVIDE 6" MINIMUM LAP JOINT. Date 05/02/2024
6" MIN
PRE FINISHED ALUMINUM BASE AND COUNTER FLASHING. ONE LAYER 5/8" TYPE X GYPSUM WALLBOARD FOR
WEEP HOLES @ 32" O.C. AT BASE FLASHING AND OVER ALL OPENINGS. Drawn by
TYP. MASONRY WALL BASE FLASHING
ONE LAYER 5/8" TYPE X GYPSUM WALLBOARD FOR FINISHED GRADE LIMITING DISTANCE LESS THAN 3'-11" (1.20m)
ASB
6" MIN
TIED TO SHEATHING UNDER BUILDING PAPER. PROVIDE 6" PROVIDE P.V.C. BRICK VENTILATOR @ ALL WEEP HOLE LOCATIONS.
MINIMUM LAP JOINT FINISHED GRADE LIMITING DISTANCE LESS THAN 3'-11" (1.20m)
PROVIDE MASONRY PARGING FROM TOP OF
MINIMUM 2"x4" SILL PLATE, TIED TO TOP OF POURED CONC. FND.
Checked by KDI
WEEP HOLES @ 32" O.C. AT BASE FLASHING AND OVER ALL MINIMUM 2"x4" SILL PLATE, TIED TO TOP OF POURED CONC. FND. FOUNDATION WALL TO 2" BELOW FINISHED GRADE
OPENINGS. PROVIDE P.V.C. PROVIDE MASONRY PARGING FROM TOP OF
FOUNDATION WALL TO 2" BELOW FINISHED GRADE
WALL WITH 8" LONGx1/2"∅ ANCHOR BOLTS C/W NUT AND WASHER UNREINFORCED SOLID CONCRETE FOUNDATION WALLS (9.15.4.2.)
WALL WITH 8" LONGx1/2"∅ ANCHOR BOLTS C/W NUT AND Scale As indicated
BRICK VENTILATOR @ ALL WEEP HOLE LOCATIONS. WASHER WITH 2 1/2" HOOK. ANCHOR BOLTS TO BE SPACED NOT
THICKNESS
20 MPa 15 MPaSTRENGTH
WITH 2 1/2" HOOK. ANCHOR BOLTS TO BE SPACED NOT MORE THAN MAX. HEIGHT FROM FIN. SLAB TO GRADE
UNREINFORCED SOLID CONCRETE FOUNDATION WALLS (9.15.4.2.) MORE THAN 7'-10" O.C. AND EMBEDDED NOT LESS THAN 4" INTO
7'-10" O.C. AND EMBEDDED NOT LESS THAN 4" INTO CONC. SUPPORTED AT TOP REVISIONS
THICKNESS
20 MPa 15 MPa STRENGTH
MAX. HEIGHT FROM FIN. SLAB TO GRADE UNSUPPORTED CONC. PROVIDE SILL GASKET BETWEEN PLATE AND FOUNDATION
PROVIDE SILL GASKET BETWEEN PLATE AND FOUNDATION WALL. AT TOP <2.5m >2.5m & <2.75m>2.75m & <3.0m
SUPPORTED AT TOP WALL. PROVIDE NON-SHRINK GROUT TO LEVEL PLATE.
AS PER ELEVATION
PROVIDE NON-SHRINK GROUT TO LEVEL PLATE.
AS PER ELEVATION
UNSUPPORTED 8" 3'-11" (1.20m) 7'-0" (2.15m) 7'-0" (2.15m) 6'-10" (2.10m)
PROVIDE BLOCKING BETWEEN STUDS AT TOP <2.5m >2.5m & <2.75m>2.75m & <3.0m
INSULATION BLANKET OR BATTS W/ REQUIRED BASEMENT WALL R- 10" 4'-7" (1.40m) 7'-6" (2.30m) 8'-6" (2.60m) 8'-2" (2.50m) INSULATION BLANKET OR BATTS W/ REQUIRED BASEMENT WALL R- No. Description Date
TO TIE CONV. 8" 3'-11" (1.20m) 7'-0" (2.15m) 7'-0" (2.15m) 6'-10" (2.10m) 12" 4'-11" (1.50m) 7'-6" (2.30m) 8'-6" (2.60m) 9'-3" (2.85m) VALUE, 6 MIL POLYETHYLENE VAPOUR BARRIER DAMPPROOF WITH
PROVIDE CONTINUOUS TYVEK SHT'G AROUND HEADERS, VALUE, 6 MIL POLYETHYLENE VAPOUR BARRIER DAMPPROOF
ROOF FRAMING 10" 4'-7" (1.40m) 7'-6" (2.30m) 8'-6" (2.60m) 8'-2" (2.50m) 8" 3'-11" (1.20m) 7'-6" (2.30m) 7'-6" (2.30m) 7'-2" (2.20m) AIR/WATER BARRIER BETWEEN THE FOUNDATION WALL AND
UNDER BASE PLATES UP WITH AIR/WATER BARRIER BETWEEN THE FOUNDATION WALL AND
12" 4'-11" (1.50m) 7'-6" (2.30m) 8'-6" (2.60m) 9'-3" (2.85m) 10" 4'-7" (1.40m) 7'-6" (2.30m) 8'-6" (2.60m) 9'-3" (2.85m) INSULATION UP TO GRADE LEVEL. TERMINATE BLANKETS ABOVE
STUD WALL BEHIND GYPSUM SHT'G-PROVIDE CAULKING AT INSULATION UP TO GRADE LEVEL. TERMINATE BLANKETS ABOVE
8" 3'-11" (1.20m) 7'-6" (2.30m) 7'-6" (2.30m) 7'-2" (2.20m) 12" 4'-11" (1.50m) 7'-6" (2.30m) 8'-6" (2.60m) 9'-3" (2.85m) SLAB AS REQUIRED BY O.B.C. OR ENERGY DESIGN CONSULTANT
SECOND FLOOR JOINT TYVEK SHT'G SLAB AS REQUIRED BY O.B.C. OR ENERGY DESIGN CONSULTANT
10" 4'-7" (1.40m) 7'-6" (2.30m) 8'-6" (2.60m) 9'-3" (2.85m) MINIMUM STRIP FOOTING SIZES (9.15.3.)
SHALL EXTEND UNDER SILL PLATE TO OUTSIDE FACE OF 12" 4'-11" (1.50m) 7'-6" (2.30m) 8'-6" (2.60m) 9'-3" (2.85m) TAPE AND SEAL BLANKETS AT ALL JOINTS NUMBER SUPPORTING INT.
TAPE AND SEAL BLANKETS AT ALL JOINTS
INSULATION UNDER 6 MIL SUPPORTING SUPPORTING
MINIMUM STRIP FOOTING SIZES (9.15.3.) SUPPORTI FLOORS LOAD BEARING
AIR VAPOUR BARRIER 12 NUMBER
FLOORS
SUPPORTING INT.
LOAD BEARING
SUPPORTI
NG
NG
SECURE METAL BLANKET TIE TO FOUNDATION SUPPORTED
16" W x 6" D 1
MASONRY WALL
16" W x 6" D 16" W x 6" D
EXTERIOR PARTYWALL
UNFINISHED BASEMENT
PARTYWAL WALL AS PER MANUF. INSTRUCTIONS
VARIES SUPPORTED MASONRY WALL EXTERIOR 24" W x 8" D 2
20" W x 6" D 24" W x 8" D SECURE METAL BLANKET TIE TO FOUNDATION
16" WLx 6" D
1 16" W x 6" D
2
16" W x 6" D
24" W x 8" D 20" W x 6" D 24" W x 8" D
UNFINISHED BASEMENT 36" W x 14" D 3
26" W x 9" D 36" W x 14" D WALL AS PER MANUF. INSTRUCTIONS
NOTE: FOOTING SIZE SUBJECT TO
3 36" W x 14" D 26" W x 9" D 36" W x 14" D CERTIFICATION BY A SOIL CONSULTANT 1/2" IMPERVIOUS BOARD FOR BOND BREAK
1/2" IMPERVIOUS BOARD FOR BOND BREAK
NOTE: FOOTING SIZE SUBJECT TO
FOUNDATION WALLS SHALL NOT EXCEED 9'-10" (3.0m) IN UNSUPPORTED 3" MIN. 25 MPa CONC. SLAB ON 4" COARSE CLEAN GRANULAROR
FILL
CERTIFICATION BY A SOIL CONSULTANT
3" MIN. 25 MPa CONC. SLAB ON 4" COARSE CLEAN GRANULAR OR HEIGHT UNLESS OTHERWISE NOTED. (9.15.4.2.1). POURED CONC. FDTN. WALL 20 MPa\ CONC. WITH DAMPPROOFING BELOW SLAB.
FOUNDATION WALLS SHALL NOT EXCEED 9'-10" (3.0m) IN UNSUPPORTED
FILL 20 MPa CONC. WITH DAMPPROOFING BELOW SLAB. WITH BITUMINOUS DAMPPROOFING AND DRAINAGE LAYER. REFER TO CHART
HEIGHT UNLESS OTHERWISE NOTED. (9.15.4.2.1). POURED CONC. FDTN. WALL
WITH BITUMINOUS DAMPPROOFING AND DRAINAGE LAYER. REFER TO CHART
BASEMENT SLAB TO FINISHED GRADE, ON CONTINUOUS KEYED CONC. FTG..
BRACE FOUNDATION WALL PRIOR TO BACKFILLING. ALL FOOTINGS SHALL
BASEMENT SLAB TO FINISHED GRADE, ON CONTINUOUS KEYED CONC. FTG..
REST ON NATURAL UNDISTURBED SOIL OR COMPACTED ENGINEERED FILL.
BRACE FOUNDATION WALL PRIOR TO BACKFILLING. ALL FOOTINGS SHALL
CONTINUOUS KEY IN CONCRETE
REST ON NATURAL UNDISTURBED SOIL OR COMPACTED ENGINEERED FILL.
CONTINUOUS KEY IN CONCRETE
4" ∅ WEEPING TILE, 6" CRUSHED STONE COVER 4" ∅ WEEPING TILE, 6" CRUSHED STONE
OVER AND AROUND WEEPING TILES. COVER OVER AND AROUND WEEPING TILES.
2"x6" SILL PLATE, TIED TO TOP OF STEEL BEAM
FLANGE WITH 1/2"∅ BUILDING COMPONENT INSULATION VALUE PROPOSED POURED CONC. FOOTINGS. SEE 'MINIMUM STRIP
4" BLOCKS WHERE NOT POURED CONC. FOOTINGS. SEE 'MINIMUM STRIP BUILDING COMPONENT INSULATION VALUE PROPOSED
FOOTING SIZES FOR EXTERIOR WALLS' CHART
EXPOSED TO
EXTERIOR
C
L
8"
BOLTS C/W NUT AND WASHER. BOLTS TO BE
SPACED NOT MORE
THAN 32" O.C.
FOOTING SIZES FOR EXTERIOR WALLS' CHART
NOTE: POURED CONC. FOOTING ON NATURAL UNDISTURBED SOIL OF

OBC REFERENCES
CEILING W/ ATTIC SPACE
CEILING W/O ATTIC SPACE
R60 (RSI 10.56)
R31 (RSI 5.46)
NOTE: POURED CONC. FOOTING ON NATURAL UNDISTURBED SOIL OF
75kPa OR COMPACTED ENGINEERED FILL WITH MIN. BEARING OBC REFERENCES
CEILING W/ ATTIC SPACE
CEILING W/O ATTIC SPACE
R60 (RSI 10.56)
R31 (RSI 5.46)
TYPICAL
9.10.3.3.(2). - EXTERIOR WALLS SHALL BE RATED TO EXPOSURE TO 9.10.3.3.(2). - EXTERIOR WALLS SHALL BE RATED TO EXPOSURE TO
STEEL BEAM W/ STL. PLATE
WELDED TO
BOTTOM FLANGE AS PER
GARAGE
75kPa OR COMPACTED ENGINEERED FILL WITH MIN. BEARING
MAXIMUM JOIST SPAN ONLY. JOIST SPAN EXCEEDING 16'-0" (4.9m)
FIRE FROM INSIDE THE BUILDING SB 2.3.5.(2). - WHEN AN
EXTERIOR WALL ASSEMBLY IS RATED FROM THE INTERIOR SIDE THE
SPACES BETWEEN THE STUDS ARE TO BE FILLED WITH INSULATION
EXPOSED FLOOR
WALLS ABOVE GRADE
R31 (RSI 5.46)
R24 (RSI 4.23)
MAXIMUM JOIST SPAN ONLY. JOIST SPAN EXCEEDING 16'-0" (4.9m)
SHALL BE ENGINEERED. IF SOIL BEARING DOES NOT MEET MINIMUM
CAPACITY, ENGINEERED FOOTINGS ARE REQUIRED. ACTUAL SOIL
FIRE FROM INSIDE THE BUILDING SB 2.3.5.(2). - WHEN AN
EXTERIOR WALL ASSEMBLY IS RATED FROM THE INTERIOR SIDE THE
SPACES BETWEEN THE STUDS ARE TO BE FILLED WITH INSULATION
EXPOSED FLOOR
WALLS ABOVE GRADE
R31 (RSI 5.46)
R24 (RSI 4.23) DETAILS
SHALL BE ENGINEERED. IF SOIL BEARING DOES NOT MEET MINIMUM BASEMENT WALLS R20 (RSI 3.52) BASEMENT WALLS R20 (RSI 3.52)
PLAN FOR CONFORMING TO CAN/ULC-S702 AND HAVING A MASS OF BEARING CAPACITY TO BE VERIFIED WITH SOIL ENGINEERING REPORT. CONFORMING TO CAN/ULC-S702 AND HAVING A MASS OF
MASONRY SUPPORT CAPACITY, ENGINEERED FOOTINGS ARE REQUIRED. ACTUAL SOIL
NOT LESS THAN 1.22 kg/m2 OF WALL SURFACE. NOT LESS THAN 1.22 kg/m2 OF WALL SURFACE.
BEARING CAPACITY TO BE VERIFIED WITH SOIL ENGINEERING REPORT. FLOOR & ROOF CONSTRUCTION
BELOW GRADE SLAB ENTIRE SURFACE > 600mm BELOW GRADE R10 (RSI 1.76) REFER TO FLOOR & ROOF TRUSS MANUFACTURERS BELOW GRADE SLAB ENTIRE SURFACE > 600mm BELOW GRADE R10 (RSI 1.76)
FLOOR & ROOF CONSTRUCTION
A-401
REFER TO FLOOR & ROOF TRUSS MANUFACTURERS EDGE OF BELOW GRADE SLAB ≤ 600mm BELOW GRADE R10 (RSI 1.76) DRAWINGS FOR SPECIFICATION, DETAILS, LAYOUT, SPACING,
EDGE OF BELOW GRADE SLAB ≤ 600mm BELOW GRADE R10 (RSI 1.76)
DRAWINGS FOR SPECIFICATION, DETAILS, LAYOUT, SPACING, INSTALLATION, HANDLING AND HANGER SIZES.
INSTALLATION, HANDLING AND HANGER SIZES. HEATED SLAB OR CONC. SLAB ≤ 600mm BELOW GRADE R10 (RSI 1.76) HEATED SLAB OR CONC. SLAB ≤ 600mm BELOW GRADE R10 (RSI 1.76)
STEEL BEAM AT GARAGE STUCCO ABOVE W/ MASONRY BELOW, 2"x6" STUDS, 2

5 STOREY WALL SECTION MASONRY VENEER, 2"x6" STUDS, 2 STOREY WALL SECTION1
1" = 1'-0" 2 1 13948 Mississauga Road, Caledon
1/2" = 1'-0" 1/2" = 1'-0"
ON
REINFORCE SLAB W/ 10M BARS @ 7 7/8" O.C. EACH DIRECTION
W/ 1.25" CLEAR COVER FROM BOTTOM OF SLAB. LAY SECOND PROJECT NAME
GENERAL STRUCTURAL NOTES LAYER OF BARS DIRECTLY ON TOP OF LOWER LAYER IN OPPOSITE
DIRECTION
10" MIN. RUN
75/ MAX. RISE

2'-11" MIN.
REINFORCE SLAB W/ 10M BARS @ 7 7/8"
A) FOUNDATIONS: O.C. EACH DIRECTION W/ 1.25" CLEAR
13948 Mississauga
6" MIN.
COVER FROM BOTTOM OF SLAB. LAY
GROUND FLOOR
8
SECOND LAYER OF BARS DIRECTLY ON TOP
1. FOOTINGS SHALL BE PLACED ON UNDISTURBED SOIL CAPABLE
OF SUPPORTING MINIMUM 75 KPa 2-15M BARS
OF LOWER LAYER IN OPPOSITE DIRECTION
Road, Caledon ON
5"
2. DO NOT PLACE FOOTINGS ON FROZEN GROUND OR IN WATER. MAX 8'-2" CLEAR SPAN BETWEEN PROVIDE 6" RAISED CONC.
SUPPORTING WALLS MEASURED CURB AT ALL EXT. WALLS
3. PLACE FOOTINGS ON UNDISTURBED MATERIAL. COMPACT GRADE ALONG THE SHORTEST DIMENSION OF EXCEPT ABUTTING GARAGE PROJECT ADDRESS
MATERIAL AS REQUIRED. THE SLAB WALL.
10M BAR W/ 1 1/2" COVER @ NOSING
4. CONTRACTOR IS RESPONSIBLE FOR PROPERLY BRACING 2'-11" MIN.
FOUNDATION WALLS DURING BACKFILLING OPERATIONS AND 13948 Mississauga Road, Caledon
10M BARS @ 16" O.C. VERTICAL
6" MIN
DURING CONSTRUCTION. THIS INCLUDES EXISTING AND NEW AND 16" O.C. HORIZONTAL W/ SLOPE TOP OF CONC SLAB ON
1.25" MIN. CONCRETE COVER
FOUNDATION WALLS.
FLOOR JOISTS
5. PROTECT FOOTINGS EXPOSED TO FROST ACTION DURING 4" MIN
CONSTRUCTION BY 4'-0" MINIMUM OF SOIL OR ITS EQUIVALENT. 5" 32MPa REINFORCED 2"x4" SILL PLATE TIED TO CONC.
GRADE
6. WHERE A FOUNDATION WALL RETAINS SOIL ON EACH SIDE, PRECAST
CONCRETE SLAB WITH 5% TO 6%
AIR ENTRAINMENT SLOPED TO
FOUNDATION WALL WITH 1/2"∅
ANCHOR BOLTS @ 7'-10" O.C.
CLIENT
PLACE BACKFILL ON BOTH SIDES SIMULTANEOUSLY. INSET STEP CONDITION STEP(S) SHED WATER AWAY FROM EMBEDDED 4" MINIMUM INTO
EXTERIOR WALL CONCRETE FOUNDATION WALL.
7. FOUNDATION WALLS RETAINING EARTH BETWEEN SLABS AT MASONRY TIES NOTE: PROVIDE SILL GASKET BETWEEN SILL
DIFFERENT LEVELS SHALL BE SHORED UNTIL THE SLAB AT HIGHER
LEVEL IS IN PLACE AND HAS REACHED ITS REQUIRED STRENGTH.
WHEN BRICK FACING IS
USED ABOVE GROUND ALUMIN. GUARDRAIL 24"x24" 10M BENT
PLATE AND FOUNDATION WALL.
PROVIDE NON-SHRINK GROUT TO HARVINDER D.
LEVEL, PROVIDE 0.76mm LEVEL SILL PLATE
B) CONCRETE SPECIFICATIONS
THICK & 22mm WIDE
CORRISION RESISTAN METAL
WHERE REQUIRED. DOWELS @16" O.C.
WITH 1.25" MIN.
CONC. COVER
FULL HEIGHT INSULATION BLANKET
OR BATTS W/ REQUIRED BASEMENT
WALL R-VALUE, 6 MIL. VAPOUR
RESIDENCE
TIES @ 600mm HORIZ. & BARRIER.
1. THE ULTIMATE 28 DAYS COMPRESSIVE STRENGTH OF CONCRETE 500mm VERTICAL
SHALL BE 20.0 MPa UNLESS OTHERWISE NOTED COLD CELLAR UNFINISHED
2. THE ULTIMATE 28 DAYS COMPRESSIVE STRENGTH OF CONCRETE ARCHITECT
EXPOSED TO FREEZING AND THAWING (EXTERIOR SLABS, GARAGE
MASONRY EXT. BASEMENT
FLOOR SLAB, SIDE WALKS, CURS, RETAINING WALLS ETC ) SHALL BE
FACING, FILL SPACE
BETWEEN WALL & 6" KHALSA DESIGN INC.
MAX.
FACING w/ MORTAR MIN.
1'-6"
32 MPa WITH MINIMUM AIR ENTRAINMENT CONTENT OF 5%-8% & PROVIDE METAL
AND MAXIMUM WATER/CEMENT RATIO BY MASS OF 0.45. TIES. 24"x24" 10M BENT TYPICAL POURED CONCRETE
DOWELS @16" O.C. WITH TYPICAL POURED CONCRETE FOUNDATION WALL.
3. DO NOT USE CALCIUM CHLORIDE OR OTHER SALTS IN 1.25" MIN. CONC. COVER FOUNDATION WALL.
MIN.
CONCRETE
6"
4. REINFORCING STEEL SHALL BE DEFORMED BARS TO CSA G30.18 4" ∅ WEEPING TILE, 6" CRUSHED STONE
PRECAST COVER OVER AND AROUND WEEPING 1/2" IMPERVIOUS BOARD FOR
WITH A MINIMUM YIELD STRENGTH OF 400MPA. 10" CONC. AT REDUCED
STEP(S) TILES. BOND BREAK OR EQUAL
FOUNDATION WALLS FOR
5. WEEDED WIRE MESS SHALL CONFORM TO CSA.G30.5, WELDED 10" MASONRY EXTERIOR
STEEL WIRE FABRIC FOR CONCRETE REINFORCEMENT.
6. DETAIL REINFORCING IN ACCORDANCE WITH REINFORCING
STEEL MANUAL OF STANDARD PRACTICE PREPARED BY RSIO.
7. ONLY READ MIX CONCRETE IS PERMITTED ON THIS JOB. THE REDUCED FOUNDATION FOR MASONRY
CONCRETE SUPPLIER SHALL BE RESPONSIBLE FOR CONCRETE MIX
DESIGN. TYPICAL CONC. PORCH DETAIL
2
1/2" = 1'-0"
D1
D1
8. SUPPLY AND INSTALL CONCRETE, REINFORCING STEEL AND
4" MAX.
FORMWORK INCLUDING PLACING, FINISHING AND CURRING AS
SHOWN ON THE DRAWINGS IN ACCORDANCE WITH CSA A23 AND MAXIMUM 4" OPENING
GSA G 30. WOOD HEADER BETWEEN PICKETS & NO
9. NON-SHRINK, NON-METALLIC GROUT SHALL BE USED BY SIKA MEMBER OR ATTACHMENT
CANADA INC. OR AN APPROVED EQUAL.

EQUAL DEPTH BEAMS BETWEEN 4" & 2'-11" SHALL
FACILITATE CLIMBING. 4" MAX.
D1 EQUAL TO D2 BRICK
4"x4" P.T. INTERMEDIATE 4"X4" P.T. MAIN CORNER POST
C) BEAM BEARING PLATE POST AT 5'-1" O.C.
MAXIMUM
BRAMPTON, ON
VERTICAL SLOTTED CONNECTION 5'-1" O.C. MAX.
D1
FOR W STEEL BEAMS BEARING ON CONCRETE FOUNDATION WALL
TELEPHONE: 647-468-2940
D1
USE STEEL PLATE GRADE G40.21-300W8" x 1/2" THICK x 1'-01" WITH STEEL LINTEL
2 2"X8" P.T. RIM BOARD
TWO 3/4" DIA. BOLTS EMBEDDED 18" INTO FOUNDATION WALL. 2"X4" P.T. TOP RAIL A-402
NOTE: ALL METAL FASTENERS 2"X4" P.T. RAIL
UNEQUAL DEPTH BEAMS SHALL BE NON-CORROSIVE.

2"X2" P.T. PICKETS CONSULTANTS:
D) WOOD
D1 GREATER THAN D2 NOTES: 2"x10" P.T. STAIR STRINGER
2"X8" P.T. BLOCKING
AT POST
1. ALL WOOD CONSTRUCTION BE IN ACCORDANCE WITH CSA S NOTES: 1. - LINTEL SIZE - SEE LINTEL SCHEDULE CONNECTION STRUCTURAL ENGINEER:
STANDARD CAN3-086-01 1. PROVIDE A 2-L4X4X3/8 BOLTED TO BOTH MEMBERS USING A325 3/4" DIA. - PROVIDE 2-2X10 (SUPPORTING NO OTHER LOADS) SEE SCHEDULE SHOWN BEYOND 2"X4" P.T. WD.
BOLTS c/w NUTS AND WASHERS. BLOCKING TIED TO STAIR 2"X8" P.T. JOISTS @ 16" O.C.
2. WALLS: - FASTEN LINTEL HEADER WITH 1/2" DIAM. LAG BOLTS. PROVIDE A MINIMUM 8" OF
STRINGER WITH 2-#7 2 1/2"
INTERIOR BEARING WALL 2x6 @ 16" O.C SPR. NO.2 2. CONNECTION RATED FOR A FACTORED REACTION OF 75KN (16,000 LBS) BEARING, EACH END. PROVIDE VERTICAL SLOTTED CONNECTIONS AT ENDS AND 30" SCREWS
3. BEAMS TO BE DESIGNED TO SUPPORT LOADS. O.C. SHORE LINTEL DURING BRICK INSTALLATION PLUS 7 DAYS AFTER COMPLETION. STRUCUTRAL SEAL:
EXTERIOR WALL 2x6 @ 16" O.C SPR. NO.2 2
4. CONNECTIONS TO BE USED ONLY FOR RESIDENTIAL APPLICATIONS. 2. - 3-1/2" FACE BRICK OR SIMILAR.
INTERIOR PARTITION WALL 2x4 @ 16" O.C SPR. NO.2 2
5. DETAIL IS ONLY TO BE USED IF SEALED BY A P.ENG. 3. - HORIZONTAL LADDER IN FIRST 5 COURSES ABOVE SOLIDER COURSE OR A-402
2-2"X8" P.T. BEAM TIED TO TOP
INTERIOR POST IN WALL 6x6 SOUTHERN PINE NO. 2 PRECAST HEADER. EXTEND 12" POST DOOR JAMB. USE TYPE S MORTAR. A-402
OF 6"X6" P.T. POSTS TIED WITH
3 1 IN.
4. - WHEN HEIGHT ABOVE GARAGE DOOR IS GREATER THAN 8'-0" INCLUDE USE OF
M
3. ALL LUMBER TO BE GRADE STAMPED AND SHALL BE DRY SPRUCE NON-CORROSIVE METAL
/2
4"x4" P.T.
"
HORIZONTAL LADER STEEL. ANCHOR BRACKET TO TOP OF
2'-11" MIN.
# 1 OR #2 CONFORMING TO CSA-086-01 INTERMEDIATE
WHEN LESS THAN 8'-0" LADDER STEEL NOT REQUIRED. POSTS AT 5'-1" 10"∅ 15 MPa POURED CONC.
4. METAL HANGERS SHALL BE MADE FROM LIGHT GAUGE O.C. PIER W/ 5%-8% AIR
2 - 1/2" DIAMETER THRU ENTRAINMENT
GALVANIZED METAL AND SHALL HAVE ALLOWABLE LOAD STEEL BEAM CONNECTIONS GARAGE BRICK LINTELS MAXIMUM
BOLTS C/W 1 POSTS TIED TO METAL SHOE
7 7/8" MAX.
2"X6" P.T. STAIR
4 7/8" MIN.
CAPACITY (AS PER MANUFACTURE'S DATA) GREATER THAN Scale= 1-1/2" = 1'-0" Scale= 1-1/2" = 1'-0" TREADS NAILED
1/4" O.D. WASHERS
ANCHOR WITH 4-3/8"∅
REACTIONS PRODUCED BY LOADING CONDITIONS. USE SIMPSON TO STAIR
1" 10" MIN.
2"X4" P.T. WD. BLOCKING MACHINE BOLTS
STRINGER 2-3" TIED TO STAIR STRINGER
STRONG-TIE OR EQUAL SPIRAL NAILS, WITH 2-#7
5. ALL ENGINEER LUMBER SHALL BE AS PER STRUCTURAL LAY TREADS @ 11" MIN. 2 1/2" SCREWS
14" MAX. FINISHED GRADE
MIN.
1/4" APART
REQUIREMENTS. ALL LSL MEMBERS SHALL HAVE A MINIMUM
6"
YOUNG'S MODULES (E) OF 1,550,000 PSI; ALL LVL'S SHALL HAVE A
MINIMUM MODULES (E) OF 2,000,000 PSI. ALL PSL'S SHALL A
1/2"∅ NON-CORROSIVE
MINIMUM YOUNG'S MODULES (E) OF 2,000,000 PSI. ENGINEER PRECAST CONCRETE PATIO
SLAB ON COMPACTED ANCHOR 4" MINIMUM
LUMBER MUST HAVE THE IDENTIFICATION MARKINGS LEFT ON FINISHED GRADE INTO CONCRETE
4'-0" MIN.
FOR FIELD VERIFICATION PURPOSES. 2"x10" P.T. STAIR STRINGER
6. USE MANUFACTURER GUIDELINES FOR MEMBER WEB OR FLANGE NUMBER OF RISERS VARY AS PER GRADE
PENETRATIONS, MAXIMUM ALLOWED NOTCHES, BRIDGING STEEL COLUMN 6X6 POST
REQUIREMENTS, INTERIOR AND EXTERIOR BEARING INFILL VOID W/
CONC. AFTER HGU5.50/10 SIMPSON TYPICAL WOOD DECK STAIR
REQUIREMENTS, ETC. 5-3/8"X5-3/8" STEEL BASE HANGER OR EQUAL 3 COPYRIGHT KDI © 2023
7. CONTRACT ENGINEER REGARDING ALL DIMENSIONAL LUMBER
COLUMN IS PLUMB
PLATE WITH (4) 1/4" DIA. 1/2" = 1'-0" THESE DRAWINGS ARE NOW AND DO
AND LEVEL
PENETRATIONS, NOTCHES, ETC. TAPCONS W/ 1" 2"X4" P.T. TOP RAIL TIED TO REMAIN THE SOLE PROPERTY OF KHALSA
EMBEDMENT RAIL WITH 1-3 1/4" SPIRAL DESIGN USE OF THESE PLANS OR ANY
8. SILL ANCHOR PLACEMENT TO BE AS FOLLOWS:
NAIL @ 12" O.C
1. NO LESS THAN (2) ANCHORS PER PLATE SECTION FORM OF REPRODUCTION OF THIS DESIGN
PREMANU. P.T. WOOD CAP
2. PLACE ANCHORS NO LESS THAN 3-1/2" AND NO FASTENED TO MAIN POST
GREATER THAN 12" FROM END PLATE. WRITTEN CONSENT IS PROHIBITED AND
NAIL DECK TO RIM BOARD
3. USE 1/2" ASTM A307 BOLTS. USE 7" MIN. 2"X4" P.T. TOP RAIL TIED
EMBEDMENT. TO POST WITH 3-2 1/2" SECTION PROSECUTION UNDER LAW
SPIRAL NAILS 2"X2" P.T. PICKETS TIED TO
4. SPACE ANCHORS AT 6'-0" O.C. MAX. RAIL WITH 2-#7 2 1/2"
LVL AS PER PLANS 2"X4" RAIL TOE NAILED SCREWS
9. PROTECT LUMBER IN DIRECT CONTACT WITH CONCRETE OR TO POST WITH 1-2 1/2" ARCHITECT SEAL:
MORTAR WITH 10 mil. POLYETHYLENE SHEET. JOISTS AS PER PLANS SPIRAL NAIL
10. PLYWOOD AS PER CSA 0 86.1 NOTE: ALL METAL FASTENERS
2"X4" P.T. TOP RAIL TIED TO
6x6 SB. POST SHALL BE NON-CORROSIVE.
POST WITH 2-2 1/2" SPIRAL
NAILS
E) STRUCTURAL STEEL 2"X2" P.T. PICKETS TIED TO
RAIL WITH 1-#7 2 1/2"
SCREWS 2"X4" P.T. BOTTOM RAIL TIED
1. STRUCTURAL STEEL SHALL BE AS FOLLOWS
2"X2" P.T. PICKETS TIED TO
TO POST WITH 3-2 1/2"
SPIRAL NAILS
05 - 02 - 2024
W, S, HP, WWF SHAPES CAN/CSA G40.21-350W RAIL WITH 2-#7 2 1/2" 2"X8" P.T. BLOCKING
HSS CAN/CSA G40.21-350W. CLASS C SCREWS
L, PL CAN/CSA G40.21-300W. CONCRETE FOOTING SECTION (TYP.) FLOOR/POST CONNECTIONS 2"X8" P.T. RIM JOIST TIED TO 4"X4" P.T.
POST WITH 4-#9X3" SCREWS PER SIDE
Scale= 1-1/2" = 1'-0" Scale= 1-1/2" = 1'-0" NOTE: ALL METAL FASTENERS (DO TYPICAL)
2. OBTAIN FIELD MEASUREMENTS AS REQUIRED. SHALL BE NON-CORROSIVE.
2-2"X8" P.T. BEAM TIED
3. PROVIDE HOLES WHERE REQUIRED FOR ATTACHMENT OF OTHER TO TOP OF 6"X6" P.T.
WORK TO STEEL. PLACE HOLES SO AS NOT TO CAUSE ANY POST Project number 24003
APPRECIABLE REDUCTION IN STRENGTH OF THE MEMBER. 2"X4" P.T. BOTTOM RAIL TIED
4. FABRICATE, SUPPLY AND ERECT STRUCTURAL STEEL WORK IN
TO POST WITH 3-2 1/2" SIMPSON'S STRONG TIE "LPCZ" Date 05/02/2024
SPIRAL NAILS POST CAP TO BE PAIRED UP AND
ACCORDANCE WITH THE FOLLOWING STANDARDS: FASTENED WITH 3" LONG NAILS Drawn by ASB
2"X8" P.T. BLOCKING
DESIGN, FABRICATION AND ERECTION CSA-S16.1 Checked by KDI
WELDING CSA-W47 2"X8" P.T. RIM JOIST TIED TO 4"X4" P.T.
POST WITH 4-#9X3" SCREWS PER SIDE
Scale As indicated
CLEANING SSPC-SP3-63
BOLTS 3/4" DIA. U.N.O. ASTM-325-80A CONNECT MEMBERS
(DO TYPICAL)
SIDE ELEVATION REVISIONS
CONNECT MEMBERS 2"X6" P.T. LEDGER TIED TO STAIR
TOGETHER WITH (2) ROWS OF
PAINT (1 SHOP COAT + FIELD TOUCH UP) CGSB-1.40- TOGETHER WITH (3) STRINGER WTH 2-#9X3" SCREWS PER
10d NAILS ON EA. SIDE @ 12" ROWS OF 10d NAILS 4" SIDE, LEDGER TIED TO BEAM No. Description Date
M89 O.C. WITH 2-#9X3" SCREWS @ 12" O.C.
ON EA. SIDE @ 16" WELDED STIFFENERS
5. DESIGN CONNECTIONS FOR THE REACTIONS PRODUCED BY THE (3) 1-3/4"x7-1/4" LVL BEAM
O.C. BOTH SIDES
LOADING CONDITIONS. (2) 1-3/4"x9-1/4" LVL 2-2"X8" P.T. BEAM TIED TO
6. NO SPLICES IN NEW BEAMS AND COLUMNS SHALL BE ALLOWED BEAM TOP OF 6"X6" P.T. POST
UNLESS APPROVED BY THE ENGINEER. FRONT VIEW 2"X2" P.T. PICKETS TIED TO RAIL WITH
7. ALL STEEL LINTELS BEARING ON MASONRY TO HAVE MINIMUM 6" 1-#7 2 1/2" SCREW
BEARING. STEEL BEAM
2"X4" P.T. TOP RAIL TIED TO
RAIL WITH 1-3 1/4" SPIRAL
CONNECT MEMBERS TOGETHER CONNECT MEMBERS 8" PACK BEAM w/ NAIL @ 12" O.C
GENERAL PLAN NOTES WITH (3) ROWS OF 10d NAILS

ON EA. SIDE @ 12" O.C.
TOGETHER WITH (3)
ROWS OF 10d NAILS
BLOCKING
2"X4" RAIL TIED TO 4"x4" P.T.
INTERMEDIATE POST W/ 2-#8 3"
2"X8" P.T. RIM JOIST TIED
TO 4"X4" P.T. POST
ON EA. SIDE @ 12" SCREWS BEYOND
(3) 1-3/4"x9-1/4" LVL BEAM
O.C. 1/2" DIA. BOLTS AT
(2) 1-3/4"x11-7/8" LVL 16" O.C.
1. USE SIMPSON LU210 HANGERS AT JOISTS WHERE REQUIRED. BEAM 2"X6" P.T. STAIR TREADS NAILED
2-2"X8" P.T. BEAM TIED
STAGGERED TO TOP OF 6"X6" P.T.
2. USE (2) JACK STUDS AND (1) KING STUD FOR (3) 2x6, (3) 2x8, AND TO STAIR STRINGER 2-3" SPIRAL
POST
NAILS, LAY TREADS @
(3) 2x10 HEADER SUPPORTS, UNLESS NOTED OTHERWISE. 1/4" APART
3. USE (1) JACK STUD AND (1) KING STUD FOR (2) 2x6 HEADER
4"x4" P.T. INTERMEDIATE SIMPSON'S STRONG TIE "LPCZ"
SUPPORT, UNLESS NOTED OTHERWISE. POST AT 5'-1" O.C. POST CAP TO BE PAIRED UP AND
1/2" THICK U-SHAPE
TYPICAL
4. USE 5/8" T&G PLYWOOD SHEATHING SUBFLOOR. ATTACH TO MAXIMUM FASTENED WITH 3" LONG NAILS
HANGER WELEDED 2 - 1/2" DIAMETER THRU
FRAMING W/ 8d NAILS @ 6 O.C. AT PANEL EDGES AND 12"
1" BOLTS C/W 1-1/4" O.D.
O.C. AT INTERMEDIATE SUPPORTS. WASHERS
5.
6d
USE 1/2" APA RATED WALL SHEATHING. ATTACH TO FRAMING W/
NAILS @ 6" O.C. AT PANEL EDGES AND 12" O.C. AT INTERMEDIATE
SIDE CONNECTION VIEW
2"X4" P.T. W'D. BLOCKING
TIED TO STAIR STRINGER WITH
DETAILS
2-#7 2 1/2" SCREWS
SUPPORTS.
2"X2" P.T. PICKETS TIED TO FRONT ELEVATION
6. USE 5/8" MIN. ROOF SHEATHING. ATTACH TO FRAMING W/ 8d STAIR STRINGER WITH 2-#7 2
NAILS @ 6" O.C. AT PANEL EDGES AND 12" O.C. AT INTERMEDIATE
A-402
1/2" SCREWS
TYP. BEAM ASSEMBLIES CUSTOM HANGER w/ STIFFENER DETAIL
SUPPORTS.
Scale= 1-1/2" = 1'-0" Scale= 1-1/2" = 1'-0"
ELEVATION PLAN
TYP. POST ANCHORAGE & CONNECTION DETAILS
3/4" = 1'-0" ON
PROJECT NAME
13948 Mississauga
Road, Caledon ON
STEEL LINTEL AS PER PLAN
MIN. 12" LONG STEEL

PROJECT ADDRESS
LINTEL AS
PER PLAN DOWNTURNED.

10M REBAR BOTH ON
SIDES EVERY 2 LAYERS
HORIZONTALLY
ISOMETRIC
12" LONG STEEL LINTEL SUPPORTING
NOTE: PERPENDICULAR STEEL LINTEL ABOVE CLIENT
ALL INSULATION VALUES AS PER
SB-10 5.5.6-2017 CLIMATE ZONE
6 (A,B) (I-P) RESIDENTIAL 15M REBAR AT 16"
O.C. VERTICALLY FULL
SECTION. REFER TO SHEET A-002
CONTINUOUS PRE MANUFACTURED ALUMINUM BASE WALL
HEIGHT OF WALL HARVINDER D.
MAX. 2.6m TALL

FLASHING WITH 1" DRIP MIN. EXTENDED UNDER EXT.
TYPE SHT'G 6" MIN. TIE TOP OF FLASHING TO ICE AND WATER
GYPSOM WALLBOARD ON
APPROVED VAPOR BARRIER ON
ICE & WATER SHIELD ADHERED TO
PLYWOOD SHEATHING. WRAP OVER STEP
SHIELD WITH SELF SEALING GALVANIZED NAILS
@ 16" O.C.. PROVIDED NON-SHRINK CAULKING AT ALL VERT.
AND HORZ. JOINTS
RESIDENCE
1 1/2" EXPANDED FLASHING AND EXTENDED TO SOFFIT AND
WOOD STUD WALL W/ REQ'D
POLYSTYRENE 4'-0" BEYOND FLASHING PROVIDE WEEP HOLES AT BASE OF FLASHING
BATT INSUL. ON EXT. DENSE LOCATED NOT MORE THAN 2'-7" APART - SEE OBC
GLASS GOLD SHEATHING STUCCO FINISH 9.20.13.8. 12" MIN. OPEN
WATER RESISTANT MOISTURE
CONTINUOUS PRE MANUFACTURED ALUMINUM THRU
WALL WEEP HOLE FLASHING WITH 1" DRIP MIN. EXTENDED
UNDER BRICK VENEER AT WEEP HOLE LEVEL. AND 6" MIN.
GRAVEL BACKFILL ARCHITECT
BARRIER TO WRAP OVER GYPSUM WALLBOARD ON APPROVED
FLASHING MEMBRANE TO BE VAPOR BARRIER ON WOOD STUD OVER ICE AND WATER SHIELD. TIE TOP OF FLASHING TO
INSTALLED BEHIND FASCIA THAT

ABUTS WALL. WATER PROOF
STEP FLASHING
STUCCO PRIMER ON
WALL W/ REQ'D BATT INSUL. ON EXT.
PLY WOOD SHEATHING
ICE AND WATER SHIELD WITH SELF SEALING NON.
CORROSIVE NAILS @ 16" O.C.. PROVIDED NON-SHRINK
CAULKING AT ALL VERT. AND HORZ. JOINTS 12" WIDE CONC. KHALSA DESIGN INC.
STUCCO PREP COAT W/
MOISTURE BARRIER INSTALLED IN PROVIDE NON-SHRINK CAULKING AT BLOCK WALL WITH
EMBEDDED AND WRAPPED FLASHING MEMBRANE TO BE INSTALLED ALL FLASHING JOINTS
"SHINGLE-FASHION" W/ FLASHING
MEMBRANE
REINFORCING MESH BEHIND FASCIA THAT ABUTS WALL.
WATER PROOF MOISTURE BARRIER
SOLID GROUT
TERMINATE 2" ABOVE INSTALLED IN "SHINGLE-FASHION" W/
FLASHING MEMBRANE EXTEND FLASHING NOT LESS THAN
FINISHED ROOF 6" VERTICAL MIN. ABOVE FINISHED
STEP FLASHING W/ 2" LAP STEP FLASHING AT EACH SHINGLE PLY ASPHALT ROOF SURFACE. BASE OF
DRAINAGE TRACK NOT LESS THAN 6" VERTICAL MIN. FLASHING TO EXTEND OVER
ABOVE FINISHED ASPHALT ROOF SHINGLES 3" MIN. TOP OF
SURFACE. BASE OF FLASHING TO
BOTTOM KICKER FLASH W/ EXTEND UNDER SHINGLES 3" MIN. TOP
FLASHING TO EXTEND UNDER
BASE WALL FLASHING 1" MIN.
WATER TIGHT DIVERTER SEAMS OF FLASHING TO EXTEND UNDER
1'-0"
(TYPICAL) BASE WALL FLASHING 1" MIN.
3" PVC DRAIN w/

FILTER FABRIC 2"x6" STUDS WALL, INSULATION,
FASCIA
SEALANT APPROVED 6 MIL VAPOUR BARRIER,
TYPICAL ASPHALT SHINGLES 1/2" GYPSUM WALLBOARD INTERIOR
TRIM AS PER ELEVATIONS
FASCIA ROOFING PAPER
15M REBAR BOTH FINISH.
1'-0"
WAYS
ROOF SHEATHING TYPICAL FLOOR CONSTRUCTION
15M REBAR BOTH
SIDES FINISH FLOOR
4" R20 RIGID

SPRAY FOAM INSULATION W/
INSULATION FOR CAULKING REQUIRED
FROST PROTECTION SOFFIT TIED TO MASONRY
EXPOSED FLOOR R-VALUE
VARIES
2'-0" 1'-0" 1'-0" AROUND FOOTING 2-2"x6" TOP PLATE
PREFINISHED FRIEZE
PROVIDE CONTINUOUS APPROVED BRAMPTON, ON
4' - 0" [1.218m] BOARD,
AIR/WATER BARRIER AROUND HEADERS,
VARIES PER ELEVATION
UNDER BASE PLATES AND UP STUD WALL
BEHIND GYPSUM WALLBOARD, PROVIDE
CAULKING AT JOINTS. TELEPHONE: 647-468-2940
CONSULTANTS:
METAL FLASHING AT STUCCO FINISH WALL (ISOMETRIC) METAL FLASHING AT MASONRY WALL (ISOMETRIC) BLOCK WALL CONC. WALL RETAINING WALL TYP. CANT. FLOOR TO EXT. w/ MASONRY VENEER STRUCTURAL ENGINEER:
7 6 5 3
1/2" = 1'-0" 1/2" = 1'-0" 3/4" = 1'-0" 1/2" = 1'-0" MEM ENGINEERING INC.
STRUCUTRAL SEAL:
GRAB BAR TO CONFORM TO 3.8.3.8.(3)(a). CONTINUOUS L-
SHAPED WITH 30" LONG HORIZONTAL AND VERTICAL
COMPONENTS, WALL MOUNTED WITH THE HORIZONTAL
COMPONENT 30" ABOVE THE FLOOR AND THE VERTICAL
COMPONENT 6" IN FRONT OF THE WATER CLOSET
ICE & WATER SHIELD (TYP.)
STUDS @ 16" O.C 2x ROLL TYPE

(DOUBLE STUDS @ 16" O.C VALLEY ASPHALT SHINGLES
STUDS DIRECTLY BEHIND (DOUBLE STUDS DIRECTLY BEHIND TOILET) FLASHING (12"
TOILET) - SEE PLANS FOR STUDS @ 16" O.C - SEE MIN.) ICE & WATER SHIELD
STUDS @ 12" O.C STUDS @ 16" O.C
STUD SIZE PLANS FOR STUD SIZE
METAL ROOF
FUTURE STRAIGHT
2'-6"
NOTE: PROVIDE MIN. 1 FUTURE L-SHAPED GRAB BAR BEHIND

1/2" TO 2" MAX. GRAB ICE & WATER SHIELD
TOILET
CLEARANCE FROM BAR BAR BESIDE TOILET
TO WALL (6) 3 1/2" TOE-NAILS 6" MIN. OVERLAP ROLL TYPE VALLEY
(4) 3 1/2" END-NAILS TO
TO BLOCKING EACH OF ICE & FLASHING
BLOCKING EACH SIDE
(TYP) SIDE (TYP) WATER SHIELD
ROOF PLAN (N.T.S.) CAULKING
(4) 3 1/2" END-NAILS
(6) 3 1/2" TOE-NAILS TO TO BLOCKING EACH TYPICAL BARREL ROOF CONSTRUCTION
6"
6" SIDE (TYP)

BLOCKING EACH SIDE EXTEND ICE & WATER
6"
(TYP) CANT. 2"x4" SPACERS 2 1/2" SHIELD UP ROOF 3'-0" MIN.

2-2"x6" BLOCKING 1
2-2"x6" BLOCKING
BEYOND FRIEZE MOLDING TO 2_"
C/W (4) 3" NAILS @ 2
2'-9" TO 3'-0"
2'-9" TO 3'-0"
ALLOW FOR ATTIC VENTILATION

C/W (4) 3" NAILS @ 4"
2'-6"
4" O/C (TYP) ATTIC SPACE

O/C (TYP)
PREFINISHED FRIEZE BOARD, VARIES
CLEARANCE MIN. 2 - 3/4" PLYWOOD SHEETS
1-1/2" TO 2" MAX.
PER ELEVATION COPYRIGHT KDI © 2023
FOR BARREL
2 - 3/4" PLYWOOD SHEETS FOR ROOF JOISTS NAILING THESE DRAWINGS ARE NOW AND DO
R25 BATT INSULATION BARREL ROOF JOISTS NAILING LVL (AS PER PLAN) REMAIN THE SOLE PROPERTY OF KHALSA
GRAB BAR TO CONFORM TO 3.8.3.8.(3)(c). WINDOW LINTEL AS PER PLAN FORM OF REPRODUCTION OF THIS DESIGN
MIN. 24" LONG GRAB BAR MOUNTED
HORIZONATALLY ON THE WALL FROM 2'-9" TO PANEL SHEATHING VARIES PER ELEV.
3'-0" ABOVE THE FLOOR AND, 6" ABOVE THE WRITTEN CONSENT IS PROHIBITED AND
WATER TANK (IF APPLICABLE)
EXTENT OF ROOF BEYOND 1/2" GYPSUM CEILING BOARD INTERIOR FINISH ON 6 MIL POLY
LINE OF CEILING BEYOND
VAPOUR BARRIER ON BOTTOM CHORD OF ROOF TRUSSES, PROSECUTION UNDER LAW
INSULATION W/ REQUIRED CEILING W/ ATTIC SPACE R-VALUE
WINDOW JAMB
STUDS @ 16" O.C ARCHITECT SEAL:

(DOUBLE STUDS DIRECTLY BEHIND TOILET)
STUDS @ 16" O.C - SEE
PLANS FOR STUD SIZE
FUTURE STRAIGHT
GRAB BAR BEHIND
TOILET
05 - 02 - 2024
(6) 3 1/2" TOE-NAILS
TO BLOCKING
NOTE: PROVIDE MIN. 1 EACH NOTE: PROVIDE MIN. 1
1/2" TO 2" MAX. 1/2" TO 2" MAX.
SIDE (TYP) TYP. BARREL ROOF CROSS SECTION
CLEARANCE FROM
BAR TO WALL (4) 3 1/2" END-NAILS
CLEARANCE FROM BAR TO
WALL
2
TO BLOCKING 1/2" = 1'-0"
6"
EACH
6"
SIDE (TYP)
FUTURE U-SHAPED
2'-6" TO 2'-11"
2'-6" TO 2'-11"
GRAB
BAR BESIDE TOILET
2-2"x6" BLOCKING
C/W (4) 3" NAILS
@ Date 05/02/2024
4" O/C (TYP)
Drawn by ASB
SHIELD UP ROOF 3'-0" MIN.
ICE & WATER SHIELD (TYP.)

Checked by KDI
EXTEND ICE & WATER
GRAB BAR TO CONFORM TO 3.8.3.8.(3)(c).

MIN. 24" LONG GRAB BAR MOUNTED Scale As indicated
HORIZONATALLY ON THE WALL FROM
2x ROLL TYPE VALLEY
2'-9" TO 3'-0" ABOVE THE FLOOR AND, 6"
ICE & WATER SHIELD (TYP.) REVISIONS
STUD WALL REINFORCEMENT FOR WATER CLOSET ABOVE THE WATER TANK (IF APPLICABLE) FLASHING (12" MIN.)

CANT. 2"x4" SPACERS 2 1/2"
BEYOND FRIEZE MOLDING TO
ALLOW FOR ATTIC VENTILATION ROOF PLAN (N.T.S.)
GRAB BAR TO CONFORM TO 3.8.3.13.(2)
(f). WALL MOUNTED CONTINUOUS L- 1'-0" TO 1'-6"
2"x10" SPR. #2
SHAPED WITH 36" LONG HORIZONTAL
AND VERTICAL COMPONENTS ON THE 3/8" PLYWOOD SHEATHING
GRAB BAR TO CONFORM TO R25 BATT INSULATION
SAME WALL AS THE CONTROLS, WITH THE
3.8.3.13.(4)(c). WALL MOUNTED METAL ROOF
HORIZONTAL COMPONENT 34" ABOVE
CONTINUOUS L-SHAPED WITH 36"
THE
LONG HORIZONTAL AND VERTICAL ICE & WATER SHIELD
FLOOR AND THE END OF THE
3'-0"
COMPONENTS, WITH THE DOTTED LINE INDICATES EXTENT

HORIZONTAL EXTENT OF TOP PLATE BEYOND
HORIZONTAL COMPONENT FROM 6" OF WINDOW LINTEL BEYOND
COMPONENT WITHIN 4" FROM ENDGE EXTEND ICE & WATER
NOTE: PROVIDE MIN. TO 8" ABOVE AND PARALLEL TO THE
OF THE SHOWER SEAT (IF APPLICABLE) SHIELD UP SIDE OF DORMER
RIM OF THE BATHTUB AND THE
3'-0"
CONTROL VALVE 1 1/2" TO WALL (ADHERE ICE & WATER

2" MAX. CLEARANCE VERTICAL COMPONENT FROM 12" TO
SHIELD TO PANEL
FROM 18" FROM THE CONTROL END OF THE
NOTE: PROVIDE MIN. SHEATHING VARIES PER
BAR TO WALL BATHTUB
1 1/2" TO WINDOW BEYOND ELEV.)
(4) 3 1/2" END-NAILS TO 2" MAX. CLEARANCE
TO
BLOCKING
6"
8"
(4) 3 1/2" END-NAILS TO FROM

BLOCKING EACH SIDE (TYP) BAR TO WALL
EACH SIDE (TYP)
(6) 3 1/2" TOE-NAILS TO (6) 3 1/2" TOE-NAILS TO
2'-10"
TYPICAL
BLOCKING BLOCKING
EACH SIDE (TYP) EACH SIDE (TYP)
SECOND FLOOR (AS
PER PLAN)
TYPICAL STUCCO WALL CONSTRUCTION

DETAILS
TYPICAL WALL
CONSTRUCTION
BEYOND
STUD WALL REINFORCEMENT FOR SHOWER AND BATHTUB
4
STUD WALL REINFORCEMENT DETAILS
1
TYP. BARREL ROOF
A-403
1/2" = 1'-0" 1/2" = 1'-0"
ON

Roof Plan 5

Uploaded by

Document Informationclick to expand document informationRoof Plan 5

Document Informationclick to expand document information

Copyright:

Available Formats

Roof Plan 5

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Roof Plan 5

Uploaded by

Copyright:

Available Formats

PROJECT NAME

0-COVER 13948 Mississauga Road, Caledon

Road, Caledon ON TRUSS MANUFACTURER:

COPYRIGHT KDI © 2023

AREA CALCULATIONS DESIGN

TOTAL NET AREA 6737 sq ft REVISIONS

LANDSCAPE AREA 40.00 % 64%

PROPOSED MAX 0.70m

PROPOSED SILT FENCE

AS PER OPSD 219.110

SUBJECT TO EASEMENT AS IN INST. No. RO1022294

PART 3, PLAN 43R-19369

CHAIN LINK FENCE

PIN 14258-0082 (LT)

STANDARDS AND SPECIFICATIONS

HAVE PUMPER NOZZLE

BFE = 282.06 OTHER UTILITIES WHEN CROSSING

AT THE PROPERTY LINE

COPYRIGHT KDI © 2023

REMAIN THE SOLE PROPERTY OF KHALSA

283 FORM OF REPRODUCTION OF THIS DESIGN

LOCATION OF ALL EXISTING UTILITIES IN THE FIELD TO BE ESTABLISHED BY THE CONTRACTOR.

IN WHOLE OR IN PART WITHOUT EXPRESS

[1.50m] [22.86m] [6.33m] SHALL RESULT IN THE FULLEST EXTENT OF

EXISTING PROSECUTION UNDER LAW

FROM SUCH INSPECTION.

GRADING & DRAINAGE NOTES

NEW PROPOSED 05 - 02 - 2024

OF LOT 27, CON. 5, W.H.S.

18'-1 LINE. THE MAXIMUM SWALE GRADIENT SHALL BE 5.0%.

MOST NORTHERLY CORNER

CANNOT BE MAINTAINED PRIOR TO EXCAVATION FOR THE FOOTINGS.

4. BRICK LINE SHALL BE 0.15m ABOVE SOD ELEVATION.

EXISTING CLEAR OF ANY 0.3m RESERVES.

ENTRANCE TO Checked by KDI

REMAIN Scale As indicated

123.33 N44°58'30"W 30.83 (D1&MEAS) RAIL FENC N44°58'30"W

IN INST. No. VS152913 AS No. 5-70 BY-LAW

AND WILL NOT ADVERSELY AFFECT ADJACENT LANDS.

PIN 14258-0104 (LT)

13948 Mississauga Road, Caledon

SIDING WALL CONSTRUCTION

UNDISTURBED SOIL OF 75kPa OR COMPACTED ENGINEERED FILL WITH MIN. K51

JOISTS AT 12" O.C.

10. REFER TO FLOOR/TRUSS MANUFACTURER DRAWINGS

11-7/8" ENG. JOISTS @ 12" O.C.

22. POUR IN PLACE CONCRETE STEPS WITH MASONRY

K32 IN ONLY 10"

11-7/8" ENG. JOISTS @ 16" O.C.

CHECK FOUNDATION FOR

K42 ROUGH- 11-7/8" ENG. JOISTS

2. STEEL STEEL DETAILING AND CONNECTION TO FORM OF REPRODUCTION OF THIS DESIGN

K10 11-7/8" ENG. JOISTS CUSTOMIZED STEEL U

1/2" STIFFENERS @ 18"

O.C. BOTH SIDES (TYP.)

11-7/8" ENG. JOISTS @ 12" O.C.

TW TALL WALL DETAIL

BLOCKING C/W 3/4" EXT. GRADE PLYWOOD