Professional Documents
Culture Documents
Rts5306e Realtek
Rts5306e Realtek
DATASHEET
i Rev 1.00
TRADEMARKS
Realtek is a trademark of Realtek Semiconductor Corporation. All other names mentioned in this document are
trademarks/registered trademarks of their respective owners.
Realtek provides this document “as is”, without warranty of any kind, neither expressed nor implied, including, but not limited to
the particular purpose. Realtek may make improvements and/or changes in this manual or in the product(s) and/or the program(s)
described in this manual at any time. This document could include technical inaccuracies or typographical errors.
Revision History
Revision Description Page Date
ii Rev 1.00
Table of Contents
1. GENERAL DESCRIPTION ......................................................................................................................................................... 1
2. FEATURES............................................................................................................................................................................... 1
3. BLOCK DIAGRAM ................................................................................................................................................................... 3
4. PIN DESCRIPTION ................................................................................................................................................................... 4
5. PIN ASSIGNMENT ................................................................................................................................................................... 5
6. ELECTRICAL CHARACTERISTICS ............................................................................................................................................. 6
7. PACKAGE DIMENSIONS ........................................................................................................................................................... 7
8. ORDERING INFORMATION ....................................................................................................................................................... 9
1. General Description
The Realtek RTS5306E USB3.0 Card Reader controller is based upon Universal Serial Bus 3.0 Specification,
which integrates USB 3.0 and USB2.0 Transceivers, MCU, SIE, regulators and memory card access units
into a single chip. It can be linked in Super Speed, High Speed or Full Speed operation and supports
TM
USB2.0/USB3.0 power saving mode. It provides 1LUN (Logic Unit Number) for Secure Digital and
TM
MultiMediaCard .
The Realtek USB3.0 Card Reader supports both the internal MCU program ROM and external Serial Flash
interface. With the external Serial flash interface, the control firmware could be easily re-configured through
USB link. This could ease the software developing works and squeeze the prototyping schedule.
The Realtek RTS5306E USB3.0 Card Reader integrates all regulators, clock generation circuitry and
MOSFET components for switching card power, and could dramatically reduce the system BOM cost.
2. Features
Compliant with Universal Serial Bus 3.0 Specification Revision 1.0
Compliant with USB Mass Storage Class Bulk only Transport Specification Rev. 1.0
Compliant with MultiMediaCard System Specification version 4.4 with 4-bit data bus
Support SD card clock 100MHz (max.) for SDR50 mode and 50MHz (max.) for DDR50 mode.
On chip MOSFET components for direct power control of all types memory cards
3. Block Diagram
HS/FS
Controller
PHY
USB
PLL SDXC/MMC
4-bit I/F
Control
Power-on Register
Reset 8051 MCU
RAM
5V to 3.3V
Regulator
ROM
Serial Flash / EEPROM
3.3V to 1.2V Interface
Regulator
4. Pin Description
I/O
Pin# Name Description
Type
1 SS_RX+ USB3.0 SuperSpeed RX D+
I
2 SS_RX- USB3.0 SuperSpeed RX D-
I
3 SS_TX+ USB3.0 SuperSpeed TX D+
O
4 SS_TX- USB3.0 SuperSpeed TX D+
O
5 USB3_AV12 Analog 1.2V for USB3.0
Power
6 RREF Connect an external resistor (6.2K ± 1%) to the Reference GND
I
7 AV33 Analog 3.3V power
Power
8 VBUS VBUS 5V power input
I
9 XTLI 12Mhz Crystal oscillator input
I
10 XTLO 12Mhz Crystal oscillator output
O
11 USB2_AV12 Analog 1.2V power
Power
12 DM USB2.0 D- signal
I/O
13 DP USB2.0 D+ signal
I/O
14 VBUS VBUS 5V power input
I
15 D3V3 Digital 3.3V power
Power
16 CARD_3V3 Power output to SD/MMC Card
O
Internal regulator for the SD card control signals. An external
17 SDREG O
capacitor should be connected.
18 SD_D1 I/O SD/MMC Card Data 1
19 SD_D0 I/O SD/MMC Card Data 0
20 SD_CLK O SD/MMC Card Clock Signal
21 SD_CMD I/O SD/MMC Card Command Signal
22 SD_D3 I/O SD/MMC Card Data 3
23 SD_D2 I/O SD/MMC Card Data 2
24 SD_WP I SD Card Write Protection pin
25 DV12S Power Digital 1.2V power
26 EEDO/MOSI I/O Serial Data Output to EEPROM or Serial Flash
27 EESK/SCK I/O Clock Signal to EEPROM or Serial Flash
28 EECS/CS# I/O Chip Select to EEPROM or Serial Flash
29 EEDI/MISO I/O Serial Data Input from EEPROM or Serial Flash
30 GPIO0 I/O General purpose input/output
31 SD_CD# I SD/MMC Card Detection pin
32 VDD_RX Power 1.2V Power for USB3.0 RX
5. Pin Assignment
SD_CMD
SD_CLK
SDREG
SD_WP
SD_D2
SD_D0
SD_D3
SD_D1
24 23 22 21 20 19 18 17
DV12S 25 16 CARD_3V3
EEDO/MOSI 26 15 D3V3
EESK/SCK 27 14 VBUS
EECS/CS#
REALTEK DP
28 13
RTS5306E
EEDI/MISO 29
LLLLLLL 12 DM
VDD_RX 32 9 XTLI
1 2 3 4 5 6 7 8
SS_TX+
SS_TX-
SS_RX+
AV33
RREF
VBUS
SS_RX-
USB3_AV12
The version number is shown in the location marked ‘VV’ and G means Green Package
6. Electrical Characteristics
6.1 Absolute Maximum Ratings
Supply Voltage ……………………………………………………………………… –0.5V to +5.5V
Operating Temperature Range ….………………………………………………….. 0°C to +70°C
Latch up Current ……………………………………………………………………………… mA
Electrostatic Discharge Voltage (HBM)………………………………………………………. KV
6.2 DC Characteristics
7. Package Dimensions
Notes :
1. CONTROLLING DIMENSION :MILLIMETER(mm).
2. REFERENCE DOCUMENTL:JEDEC MO-220.
8. Ordering Information