PIPING PRESENTATION

Presented by
Salah M. Hashish
Project Quality Manager
 TOPICS COVERED
Introduction To Piping System

Piping Components

Testing Of Piping Systems

 BLOCK DIAGRAM OF PIPING ENGINEERING
PROCESS FLOW
DIAGRAM

PIPING &
INSTRUMENTATION
DIAGRAM

EQUIPMENT
LAYOUT

PIPING GENERAL
ISOMETRIC DRAWINGS ARRANGEMENT MATERIALTAKE OFF

PIPE SUPPORT
FABRICATION GAD PURCHASE SPECIFICATION
DRAWINGS
PIPE SUPPORT

FABRICATION
DRAWINGS INSTALLATION
 PIPING SYSTEM

It convey the fluids, between the various

equipment and end users.
It consists of various components such as pipes,
valves, fittings, online measuring instruments,
etc
DIFFERENCE BETWEEN PIPE AND TUBE

PIPE
• It is a tubular product of circular cross section that
has specific sizes and thickness governed by
particular dimensional standards.

TUBE
• It is a hollow product having circular, elliptical or
square cross section or cross section of of any closed
perimeter. Tubes are also used for heat transfer
purpose.
 PIPE PRODUCTS
SEAMLESS PIPE-
A wrought tubular product made without a welded seam by
drawing or extrusion process

WELDED PIPES
Welded pipes are manufactured by ERW ( Electric Resistance
Welded).
Pipes in small quantities are manufactured by EFW(electric
fusion -welding) process .
The longitudinal seam is welded by manual or automatic
electric arc process.
CLASSIFICATION BASED ON END USE:
LINE PIPE
It is mainly used for conveying fluids over long distances and are
subjected to fluid pressure
It is usually not subjected to high temperature
PRESSURE PIPE
These are subjected to fluid pressure and /or temperature .
Fluid pressure in generally internal pressure or may be external
pressure (e.g.jacketed piping )and are mainly used as plant piping.
STRUCTURAL PIPE
These are not used for conveying fluids and not subjected to fluid
pressures or temperature. They are used as structural components (e.g
handrails, columns, sleeves etc.) and are subjected to static loads
only.
 NOMINAL PIPE SIZE (NPS)
Pipes are designated by nominal size, starting from 1/8” nominal
size, and increasing in steps,
For the nominal size up to including 12” there is one unique
O D (different from nominal size)and I D would vary depending on
schedule number .
For nominal sizes 14” and above O.D is same as nominal size.

WHY PIPE SIZE IS MORE IMPORTANT

According to American Survey 30 % of the total cost of a chemical
process plant goes for piping elements and valves.

Take optimum pipe size while designing the pipe size.

 AVAILABILTY OF PIPE SIZES
1.Sizes in steps of 1/8” from 1/8”to ½”
2.Sizes in steps of ¼”from ½” to 1 ½”
3 Sizes in steps of ½” from 1 ½” to 4”
4.Sizes in steps of 1” from 4” to 6”

5.Sizes in steps of 2” from 6” to 36”

 WALL THICKNESS TOLERANCE
MILL TOLERANCE
During manufacturing of seamless pipe while positioning the
mandrel, this can deviate from its center by maximum of ±12.5%
Hence minimum thickness of seamless pipe is considered ±12.5% less
from average wall thickness.

MILL LENGTH
Also known as random length .The usual run off mill pipe is 16 – 20 ft
in length.
Line pipe and pipe for power plant used are sometimes made in double
length of 30-35 ft.
 SCHEDULE NUMBER
Pipes are designated by schedule number .
Schedule number is represented by the pressure carrying
capacity of the pipe.
1000 x P (Internal pressure)

Sch .No =
S(Allowable tensile strength of material)
Irrespective of pipe dia, equal schedules have equal
pressure carrying capacity.
For stainless steels schedule number are designated by
suffix S ie 5S, 10S, 40S, 80S etc
Piping Schedule
 COMPONENTS IN PIPING SYSTEM.
Pipe
Fittings (Elbows, Tees, Reducers, Couplings, Unions, Olets)
Flanges
Gaskets
Fasteners
Valves
Special fittings
Specialty items (strainers, traps, bellows etc)
 FITTINGS
Pipe fittings are the components which tie together
pipelines, valves, and other parts of a piping system.
Fittings may come in butt Welded, Socket welded,
Screwed and flanged connections.
They are used to change the size of the line or its direction.
 STANDARD PIPE FITTINGS
End BUTT WELD/SOCKET WELD/SCREWED/FLANGED
connections
Types

ELBOW TEES CAPS REDUCER STUB END COUPLINGS SWAGE UNIONS

NIPPLE

REDUCIN LONG SHORT CONCENTRIC ECCENTRIC

EQUAL
G STUB END STUB ENDS SWAGE NIPPLE SWAGE NIPPLE
TEES
TEES

45 90 CONCENTRI ECCENTRIC FULL HALF REDUCING SPECIAL

DEG. DEG. C REDUCERS COUP- COUP- COUPLINGS FITTINGS
ELBO ELBO REDUCERS LINGS LINGS
W W

LATROLET WELDOLET ELBOWLET SOCKOLET THREADOLET SWEEPOLET NIPPOLET

 Common Pipe Fittings

Equal Tee
90° Elbow

Concentric Reducer Eccentric Reducer

 TEES
STRAIGHT TEE / EQUAL TEE
It is used when the branch and header are the same.
REDUCING TEE
It is used when the branch size is smaller than the header
size.
POINT TO REMEMBER
It is expensive and requires three butt welds.
Alternatively for low pressure services , branching off is
done by direct welding of pipe to pipe instead of
standard Tee.
 ELBOWS
They are used to change direction of pipe.
LONG RADIUS (LR) AND SHORT RADIUS
(SR)ELBOWS.
90 degree elbow comes in LR and SR.
45 degree elbow comes in LR only.

The LR elbows radius is 1.5 times the nominal size.The SR

elbows radius is 1 times the nominal size.
Normally elbows are butt-welded, socket welded or sometimes
bolted connections are also available. Reducing elbows are
available on 90 degree only and the radius is 1.5 times of the
larger end
 MITRE BENDS
These are fabricated bends for larger diameter piping, low
pressure ( 50 psig are less ) pressure applications
It is made out of two, three, four segments of pipe pieces.
These are normally used for non critical services. ( water,
drainage, and wend piping )
 COUPLINGS
FULL COUPLING

It is used to connect small bore pipes as projection of

welding inside the pipe bore reduce the flow area
HALF COUPLING :

It is used for branch connection

UNIONS
It is used where dismantling of the pipe is required
more often.
It can be with threaded end or socket weld ends.
 REDUCERS
It makes reduction in line size
ECCENTRIC REDUCER

It is used to pump suction to avoid cavitations with

top surface being flat
To maintain elevation bottom of pipe (BOP) in
rack .
Offset dimension is ½ the difference of the two
inside diameters.
Eccentric reducer are costlier than concentric
reducer . Designer to optimize the requirement
 REDUCERS
CONCENTRIC REDUCER
It is used on pump discharge ,vertical pipe line etc.

SWAGE NIPPLE
It is also like a reducer, it connect butt welded pipe to
smaller screwed or welded pipe .
concentric and eccentric swage nipples are also available.
 SLIP ON SOCKET WELDING FLANGE
BLIND FLANGES FLANGES

THREADED WELDING NECK

LAP-JOINT FLANGE FLANGES FLANGES
 FLANGES
Flanges can be classified based on the attachment to the
piping
SLIP ON
These flanges are attached by fillet welding
inside as well as outside.

Used where quick assembly, saving in cost

and where extreme load condition are not present .
SOCKET WELD
These flanges are welded only one side .
Is is used for small bore only.
 FLANGES
SCREWED
These flanges are used on pipe lines
where low pressure and temperature are envisaged. Generally
used in galvanized lines.

BLIND FLANGE
These flanges are used to close the ends which need to be reopened
later, also used for blanking the dead end during hydro test.
 FLANGES
LAP JOINT
These flanges are used with stub ends
when piping is of a exotic material.

Stub ends will be butt welded to the piping and the flanges are keep
loose over the same.
WELDING NECK
These flanges are generally
butt welded to the pipes.

Where excessive direct bending stress

on the flanged joint or supporting heavy equipment are envisaged.
BUTT WELDED FITTINGS (ASME B16.9)
ADVANTAGES
Higher pressure and temperature conditions.
Leak proof joints and almost maintenance free.

DISADVANTAGE
Weld projection will affect flow.
Edge preparation is necessary.
 RATING OF FLANGE
Flange are also classified by pressure – temperature ratings
as per ANSI B 16.5.
It is available in seven ratings 150#, 300#, 400#, 600#,
900#, 1500# and 2500#
These flange rating are called nominal rating.
pressure –temperature combines determines the flange
rating.
 CLASSIFICATION OF FLANGES BASED ON FACING

FLAT FACE
Normally C I flanges having 125 # has a flat face. Since no
raised face it requires full faced gasket.

RAISE FACE
Raised face 1/16” for 150 # and 300 #
Raised face ¼” for other series

RING TYPE JOINT

Metallic rings are used in this
ring type joint (RTJ) flanges
SURFACE FINISH ON THE FLANGE
Normally smooth finish is recommended for metallic
gaskets.
Serrated finish are used when non metallic gaskets are
used.
SOCKET WELDED FITTINGS (ASME B16.11)
ADVANTAGES
Fast production, No need to bevel the edges.
Can be used in lieu of thread fittings.

Weldment can not extend in to the pipe line.

DISADVANTAGE
The 1/16” recess pocket liquid
Use not permitted by code if severe erosion or crevice
corrosion anticipated.
 FLANGED FITTINGS
(ASME B16.1 AND B16.5)

ADVANTAGE
Easy to dismantle and assemblelded fitting.
Occupy more space, and more weight load.
REINFORCED FITTINGS
 REINFORCED FITTINGS
WELDOLET
An economical butt -weld branch connection,
is designed to minimize stress concentration

and provide integral reinforcement.

SOCKOLET
Utilizes the basic weldolet design configuration
and incorporates a sockolet -weld outlet.
 REINFORCED FITTINGS
ELBOWOLET
utilizes the basic weldolet configuration,
provides at branch connection on elbow.

LATROLET
Used for 45 degree lateral connections.
Similarly, elbolet, sweepolet etc are available
 THERMAL EXPANSION OF PIPE
Each material has its own coefficient of thermal
expansion.
If the pipe is of carbon steel or low alloy steel, it will
expand at the rate of 6 to 7 mm every meter length as
the temperature raises to 500 degree C.
To accommodate the thermal expansion, these joints are
provided.
 EXPANSION JOINTS
Expansion joints are used to accommodate certain degree of linear
expansion and torsional misalignments in the piping system
BELLOW TYPE
Metallic bellows of compatible materials (usually stainless steels)
are used to compensate the thermal expansion.Thickness of bellows
normally 1 to 2mm.
 EXPANSION LOOPS
Expansion loops are widely used for high temperatures &
high pressures applications.Ideally suitable for longitudinal
movements and certain degree of torsional movement.
TELESCOPIC TYPE
These joints ideally suitable for low temperature & low
pressure application. Suitable only for axial expansion
 VALVES
valves are installed in between the pipes / equipment to
perform following functions :
Isolation (gate valve, ball valve, butterfly valves etc)
Regulation (globe valve etc)
Non return (check valve, SDNR etc)
Special purpose (foot valve etc)
 BALL VALVE

Ball valve is normally used for positive shut off.

Operation by a quarter turn of operating handle.
The ball valve offers minimum resistance to flow.

Widely used on onshore/offshore and petrochemicals.

GLOBE VALVE

Due to its globular body, it is called

Globe Valve.
There is higher resistance and pressure
drop in this valve.
Most suitable for throttling the flow.
 GATE VALVE
Flow is axial piping
Lower pressure drop

It is not recommended for throttling the

flow.
 BUTTERFLY VALVE
It is widely used on low pressure application . It
may be used to control and regulate the flow.
CHECK VALVE / NON RETURN VALVE

Swing Check Valve

This valve allows flow in one
direction only.
Return flow will automatically
close the valve, thus preventing
flow in reverse direction.
 TESTING OF PIPING SYSTEM
(AS PER ANSI B 31.3)

Piping system can be tested for leak tightness and

pressure integrity by hydro test / pneumatic test
methods.
 HYDROSTATIC TEST
1.5 Design Pressure x stress value at test temp
TEST PRESSURE
stress value at design temperature

TEST DURATION
A leak test shall be maintained for at least 10 minutes, and all joints
may be examined for leaks.

TEST MEDIUM
Water at ambient temperature is the test medium. Incase of
possibility of freezing exists, other fluids may be used.
 PNEUMATIC TEST

TEST PRESSURE
(1.1 x Design Pressure x stress value at test Temperature)
/ stress value at design temperature

TEST DURATION
A leak test shall be maintained for at least 10 minutes,
and all joints may be examined for leaks.

TEST MEDIUM
Air at ambient temperature is the test medium
 CHECK LIST FOR HYDRO TEST
1. COMPLETION OF WELDING ON PRESSURE
PARTS
2. ALL LONG SEAMS & CIRC. SEAMS ARE MADE
VISIBLE FOR INSPECTION.
3. COMPLETION OF ALL NDT
4. GASKETS & GASKET SEATINGS ARE CHECKED
FOR ANY DAMAGE
5. EQUIPMENT WHICH IS NOT TO BE TESTED
SHALL BE EITHER DISCONNECTED OR
ISOLATED.
 CHECK LIST FOR HYDRO TEST
5. RAISE THE PRESSURE TILL 50% OF TEST
PRESSURE.
6. INCREASE THE PRESSURE IN INCREMENTS OF
10% OF TEST PRESSURE
7. STOP PUMPING FOR 5 MINUTES AFTER EACH
INCREMENT OF 10% OF RISE IN PRESSURE.
8. IF ANY LEAKAGE IS OBSERVED THROUGH
GASKET CONNECTION, REPEAT THE TEST
AFTER DEPRESSURISING THE SYSTEM
 FITTING ARRANGMENT

Arrangement for Inlet Pressure Gauge Arrangement for Outlet Pressure Gauge

Towards Venting pipe

Pressure Gauge

Valves Valves

Coupling Pressure Gauge

From Hydrotest
Pump
Square Bar
Square Bar
Coupling

Towards Drain
 IMPORTANT SAFETY POINTS
• DRAIN THE PIPE ONLY WHEN TOP OUT LET IS
KEPT OPEN
• USE MINIMUM 2 GAUGES FOR ANY
HYDROTEST
• NEVER USE HIGH DISCHARGE PUMPS FOR
TESTING LOW VOLUME PIPE. ( VOLUM LESS
THAN 10 M3).
• NEVER PRESSURISE ANY VESSELABOVE
TEST PRESSURE
 COMMAN ABBREVIATION IN PIPING
EJMA Expansion Joint Manufacture Association .
IGSCC Inter Granular Stress Corrosion Cracking.
NFPA National Fire Protection Association
SCC Stress Corrosion Cracking.
HVAC Heating, Ventilating and Air Conditioning .
AISC American Institute of Steel Construction.
ANSI American National Standard Institute.
AISI American Institute Of Steel & Iron
MSSSP Manufacture Standard Society & Standard
Practice
TEMA Tubular Exchanger Manufacturers Association
REASON FOR CHECKING 1.5 TIMES OF
DESIGN PRESSURE
Normally 66% of yield strength (ie 2/3 yield strength) or 1/3
of the tensile strength which ever is less is taken as a basic
Allowable stress for metals considered for design calculation
.when you test the materials for 1.5 times of the design
pressure it is not exceeding 100% of yield strength of the
material. Hence all pipelines are tested for 1.5 times of the
design pressure .
2/3 of yield strength is 66 %
1.5 times of 66 % is 99 %
 REASON FOR 22% ELONGATION ON
STEEL .
Normally 12 % of the ductility required in final
product.during manufacturing. 6 to 8 % ductility lost in
manufacturing and 2 % is considered for non -
homogenous material.
Hence material selected should have minimum 22 %
elongation.
 PIPING FABRICATION

- cutting
- bending
- forming
- welding
Cutting and bevelling of the edges by Mechanical Methods
(lathes,grinding Wheels / Thermal methods (oxy – fuel gas
cutting, Arc cutting.)
 PIPING

THINNING

Bending results in the thinning of the outer surface

(extrados ) and thickening of the inner surface (intrados )
of the pipe.
It can be approximated by multiplying the thickness of the
pipe before bending by
R (
R+ r)
Where R - Radius of Bend &
r - Pipe radius. ( Half of the O.D )
 Ovality
The pipe while being bent assumes a oval shape with the
major axis perpendicular to the plane of the bend
Acceptable normally 8% for internal pressure
& 3% for external pressure.
 BUCKLING
Bending of pipe with large diameter to thickness ratios
often results in buckling rather than thickening of the
intrados even where internal mandrels are used.

Ratio of the distance between the crest to depth must be equal

to or greater than 12 (A/depth > 12)
(OD 1) + (OD 3)
Depth = – (OD 2)
2
 BENDING
COLD BENDING
Where sufficient quantities of repetitive bends are required,
ferrous pipes and tubes up to NPS 10 or 12 with wall thickness
of ½ in or less are most often bent at ambient temperature
using some type of bending machine.
HOT BENDING
Carried out in the temperature range of 1036*c to 1121*c by
induction bending. Where suitable cold bending equipment
is unavailable
Pipes of size NPS 3 ½ to NPS 64, radius of 8 to 400 inch
and wall thickness 4” can be bend by Induction Bender .
THANK YOU