C6D Ai Fcc-Sdoc

Test Report
(Supplier’s Declaration of conformity)
For
Streamax Technology Co., Ltd.
CAMERA
MODEL No.: C6D AI
Prepared for : Streamax Technology Co., Ltd.

Address : 21-23/F, Building B1, Zhiyuan, No. 1001 Xueyuan Avenue,
Nanshan District, Shenzhen City, Guangdong Province,
P.R.China
Prepared by : EMTEK (SHENZHEN) CO., LTD.

Address : Bldg 69, Majialong Industry Zone, Nanshan District,
Shenzhen, Guangdong, China
Tel: (0755) 26954280
Fax: (0755) 26954282
Report Number : ES190925017E

Date of Test : October 08,2019 to October 29, 2019
Date of Report : October 30, 2019
TRF NO. FCC15/A Page 1 of 36 Report No.: ES190925017E Ver.1.0

TABLE OF CONTENT
Test Report Description Page
1. SUMMARY OF TEST RESULTS.......................................................................................................................... 5
2. GENERAL INFORMATION .................................................................................................................................. 6
2.1. Description of Device (EUT) ........................................................................................................................... 6
2.2. Input / Output Ports ......................................................................................................................................... 7
2.3. Independent Operation Modes ....................................................................................................................... 7
2.4. Test Manner .................................................................................................................................................... 7
2.5. Description of Test Facility .............................................................................................................................. 8
2.6. Test Software .................................................................................................................................................. 8
2.7. Measurement Uncertainty............................................................................................................................... 8
3. MEASURING DEVICE AND TEST EQUIPMENT ................................................................................................ 9
3.1. For Power Line Conducted Emission Measurement ...................................................................................... 9
3.2. For Radiated Emission Measurement ............................................................................................................ 9
4. POWER LINE CONDUCTED EMISSION MEASUREMENT ............................................................................. 10
4.1. Block Diagram of Test Setup ........................................................................................................................ 10
4.2. Limits............................................................................................................................................................. 10
4.3. Test Procedure.............................................................................................................................................. 10
4.4. Measuring Results ......................................................................................................................................... 11
5. RADIATED EMISSION MEASUREMENT (UP TO 1GHz) ................................................................................. 12
5.2. Radiated Limit ............................................................................................................................................... 12
5.3. Test Procedure.............................................................................................................................................. 12
5.4. Measuring Results ........................................................................................................................................ 13
6. RADIATED EMISSION MEASUREMENT (ABOVE 1GHz) ............................................................................... 16
6.2. Radiated Limit ............................................................................................................................................... 16
6.3. Test Procedure.............................................................................................................................................. 16
6.4. Measuring Results ........................................................................................................................................ 17
7. PHOTOGRAPHS ................................................................................................................................................ 20
7.1. Photos of Radiation Emission Measurement ............................................................................................... 20
APPENDIX A: Warning Labels
APPENDIX B: Warning Statement
APPENDIX C: Photos of EUT

TEST REPORT DESCRIPTION
Applicant : Streamax Technology Co., Ltd.

21-23/F, Building B1, Zhiyuan, No. 1001 Xueyuan Avenue, Nanshan District,
Address： Shenzhen City, Guangdong Province, P.R.China
Manufacturer : Streamax Technology Co., Ltd.

21-23/F, Building B1, Zhiyuan, No. 1001 Xueyuan Avenue, Nanshan District,
Address： Shenzhen City, Guangdong Province, P.R.China
EUT : CAMERA
Model Name : C6D AI
Trademark : N/A
Measurement Procedure Used:
FCC Rules and Regulations Part 15:2017 Subpart B

ANSI C63.4-2014
The device described above is tested by EMTEK (SHENZHEN) CO., LTD. to determine the maximum
emission levels emanating from the device and the severe levels of the device can endure and its
performance criterion. The measurement results are contained in this test report and EMTEK
(SHENZHEN) CO., LTD. is assumed full of responsibility for the accuracy and completeness of these
measurements. Also, this report shows that the EUT (Equipment under Test) is technically compliant
with the FCC requirements.
This report applies to above tested sample only and shall not be reproduced in part without written
approval of EMTEK (SHENZHEN) CO., LTD.
Prepared by :
Sewen Guo /Editor
Reviewer :
Joe Xia/Supervisor
Approved & Authorized Signer :

Lisa Wang/Manager

Modified Information
Version Report No. Revision Data Summary
Ver.1.0 ES190925017E October 30, 2019 Original Version

1. SUMMARY OF TEST RESULTS
EMISSION
Description of Test Item Standard & Limits Results
Conducted Disturbance at Mains FCC Part 15, Subpart B- Section 15.107, Class B
N/A
Terminals ANSI C63.4-2014
FCC Part 15, Subpart B- Section 15.109, Class B
Radiated Disturbance Pass
ANSI C63.4-2014
Note: N/A is an abbreviation for Not Applicable.

2. GENERAL INFORMATION
2.1. Description of Device (EUT)

EUT : CAMERA
Model Number : C6D AI
Power supply : DC 12/24V for DC power
Applicant : Streamax Technology Co., Ltd.
Address : 21-23/F, Building B1, Zhiyuan, No. 1001 Xueyuan Avenue, Nanshan
District, Shenzhen City, Guangdong Province, P.R.China
Manufacturer : Streamax Technology Co., Ltd.
Address : 21-23/F, Building B1, Zhiyuan, No. 1001 Xueyuan Avenue, Nanshan
District, Shenzhen City, Guangdong Province, P.R.China
Date of Received : September 29,2019

2.2. Input / Output Ports
EUT Cable List and Details
Cable Description Length (m) Shielded/Unshielded With / Without Ferrite
DC cable 1.0 Shielded With Ferrite
Auxiliary Cable List and Details

Cable Description Length (m) Shielded/Unshielded With / Without Ferrite
/ / / /
Auxiliary Equipment List and Details

Description Manufacturer Model Serial Number
/ / / /
Notes:
1. All the equipment/cables were placed in the worst-case configuration to maximize the emission
during the test.
2. Grounding was established in accordance with the manufacturer’s requirements and conditions for the
intended use.
2.3. Independent Operation Modes

A. On
1. Normal (video & monitoring)
2.4. Test Manner

Test Items Test Voltage Operation Modes Worst case
Conducted Emission / N/A
Radiated Emission DC24V Mode A

2.5. Description of Test Facility
Site Description
EMC Lab. : Accredited by CNAS, 2018.11.30
The certificate is valid until 2022.10.28
The Laboratory has been assessed and proved to be in
compliance with CNAS-CL01:2006 (identical to ISO/IEC
17025:2017)
The Certificate Registration Number is L2291
Accredited by TUV Rheinland Shenzhen 2018.03.30

The Laboratory has been assessed according to the requirements
ISO/IEC 17025
Accredited by FCC, August 09, 2018

Designation Number: CN1204
Test Firm Registration Number: 882943
Accredited by A2LA, August 08, 2018
The Certificate Registration Number is 4321.01
Accredited by Industry Canada, November 09, 2018

The Conformity Assessment Body Identifier is CN0008
Name of Firm : EMTEK(SHENZHEN) CO., LTD.

Site Location : Bldg 69, Majialong Industry Zone,
Nanshan District, Shenzhen, Guangdong, China
2.6. Test Software

Item Software
Conducted
: EMTEK(Ver.CON-03A1)-Shenzhen
Emission
Radiated Emission : EMTEK(Ver.RA-03A1)-Shenzhen
2.7. Measurement Uncertainty
Test Item Uncertainty

Conducted Emission Uncertainty : 3.16dB(9k~150kHz Conduction 2#)
2.90dB(150k-30MHz Conduction 2#)
Radiated Emission Uncertainty : 3.78dB (30M~1GHz Polarize: H)

(3m Chamber) 4.27dB (30M~1GHz Polarize: V)
4.46dB (1~6GHz)

3. MEASURING DEVICE AND TEST EQUIPMENT
3.1. For Power Line Conducted Emission Measurement

Used Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval
Rohde &
 Test Receiver ESCS30 828985/018 May 21, 2019 1 Year
Schwarz
ROHDE &
 L.I.S.N. ESH3-Z5 100191 May 20, 2019 1 Year
SCHWARZ
50Ω Coaxial
 Anritsu MP59B M20531 May 21, 2019 1 Year
Switch
Rohde &
 Pulse Limiter ESH3-Z2 100006 May 20, 2019 1 Year
Schwarz
3.2. For Radiated Emission Measurement

Used Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval
EMI Test Rohde & ESU 1302.6005.26 May 21, 2019 1 Year

Receiver Schwarz
 Pre-Amplifier HP 8447F 2944A07999 May 20, 2019 1 Year
 Bilog Antenna Schwarzbeck VULB9163 142 May 20, 2019 1 Year
 Cable Schwarzbeck AK9513 ACRX1 May 21, 2019 1 Year
 Cable Rosenberger N/A FP2RX2 May 21, 2019 1 Year
 Cable Schwarzbeck AK9513 CRPX1 May 21, 2019 1 Year
 Cable Schwarzbeck AK9513 CRRX2 May 21, 2019 1 Year
EMI Test Rohde & ESU 1302.6005.26 May 21, 2019 1 Year

Receiver Schwarz
 Pre-Amplifier A.H. PAM-0126 1415261 May 20, 2019 1 Year
 Horn Antenna Schwarzbeck BBHA 9120 707 May 20, 2019 1 Year
Cable H+B 0.5M 289147/4 May 21, 2019 1 Year

SF104-26.5
 Cable H+B 3M SF104-26.5 295838/4 May 21, 2019 1 Year
 Cable H+B 6M SF104-26.5 295840/4 May 21, 2019 1 Year

4. POWER LINE CONDUCTED EMISSION MEASUREMENT
4.1. Block Diagram of Test Setup
Metal ground plane

Metal ground plane
Test receiver
EUT AE
80cm 50Ω
80cm
LISN LISN
LISN: Line Impedance Stabilization Network

AE: Associated equipment
EUT: Equipment under test
4.2. Limits
FCC Part 15, Subpart B, Class B
Frequency Limit (dBµV)

(MHz) Quasi-peak Level Average Level
0.15 ~ 0.50 66.0 ~ 56.0 * 56.0 ~ 46.0 *
0.50 ~ 5.00 56.0 46.0
5.00 ~ 30.00 60.0 50.0
NOTE1-The lower limit shall apply at the transition frequencies.
NOTE2-The limit decreases linearly with the logarithm of the frequency in
the range 0.15MHz to 0.50MHz.
4.3. Test Procedure

The EUT was placed on a desk 0.8 m height from the metal ground plane and 0.4 m from the
conducting wall of the shielding room and it was kept at least 0.8 m from any other grounded
conducting surface. The size of the table will nominally be 1.5 m x1.0 m.
The rear of the arrangement shall be flush with the back of the supporting tabletop unless that would
not be possible or typical of normal use.
All units of equipment forming the system under test (includes the EUT as well as connected
peripherals and associated equipment or devices) shall be arranged such that a nominal 0.1 m
separation is achieved between the neighboring units.
Connect EUT to the power mains through a line impedance stabilization network (LISN). Where the
mains cable supplied by the manufacturer is longer than 1 m, the excess should be folded at the
centre into a bundle no longer than 0.4 m, so that its length is shortened to 1 m.
All the support units are connecting to the other LISN.
The LISN provides 50 ohm coupling impedance for the measuring instrument.
Both sides of AC line were checked for maximum conducted interference.
The frequency range from 150 kHz to 30 MHz was sweep.
Set the test-receiver system to quasi peak detect function and average detect function, and to
measure the conducted emissions values.
Test results were obtained from the following equation:

Emission Level (dBμV) = LISN Factor (dB) + Cable Loss (dB) + Reading (dBμV)
Margin (dB) = Emission Level (dBμV) - Limit (dBμV)
4.4. Measuring Results
Not Applicable
EUT is DC Power.

5. RADIATED EMISSION MEASUREMENT (UP TO 1GHz)

3m
RF Cable
4m
EUT
1m Test table & Turntable 80 cm
Pre-Amplifier
EMI Test Receiver Ground Plane
5.2. Radiated Limit

Frequency Distance Field Strengths Limit

MHz Meters µV/m dB(µV)/m
30 ~ 88 3 100 40.0
88 ~ 216 3 150 43.5
216 ~ 960 3 200 46.0
960 ~ 1000 3 500 54.0
5.3. Test Procedure

The EUT was placed on a non-conductive table whose total height equaled 80cm. All units of
equipment forming the system under test (includes the EUT as well as connected peripherals and
associated equipment or devices) shall be arranged such that a nominal 0.1 m separation is achieved
between the neighboring units. Where the mains cable supplied by the manufacturer is longer than 1
m, the excess should be folded at the centre into a bundle no longer than 0.4 m, so that its length is
shortened to 1 m.
The EUT was set 3 meters away from the receiving antenna that was mounted on a non-conductive
mast. The antenna can move up and down between 1 to 4 meters to find out the maximum emission
level.
The turntable can rotate 360 degree to determine the position of the maximum emission level.
The initial testing identified the frequency that has the highest disturbance relative to the limit while
operating the EUT in typical modes of operation and cable positions in a test setup representative of
typical system configuration.
The identification of the frequency of highest emission with respect to the limit was found by
investigating emissions at a number of significant frequencies. The probable frequency of maximum
emission had been found and that the associated cable and EUT configuration and mode of
operation had been identified.
The bandwidth of the Receiver is set at 120 kHz.

Emission level (dBμV/m) = Antenna Factor -Amp Factor +Cable Loss + Reading
Margin (dB) = Emission Level (dBμV/m) - Limit (dBμV/m)
PASS.

6. RADIATED EMISSION MEASUREMENT (ABOVE 1GHz)
3m
RF Cable
4m
EUT
1m
Test table & Turntable 80 cm
Pre-Amplifier
Spectrum Analyzer Ground Plane
6.2. Radiated Limit

Frequency range Average limit Peak limit

GHz dB(µV/m) dB(µV/m)
Above 1000 54 74
Note: The highest internal source of an EUT is defined as the highest frequency generated or used in the
device or on which the EUT operates or tunes. If the highest frequency of the internal sources of the EUT is
less than 1.705 MHz, the measurement shall only be made up to 30 MHz. If the highest frequency of the
internal sources of the EUT is between 1.705 MHz and 108 MHz, the measurement shall only be made up
to 1 GHz. If the highest frequency of the internal sources of the EUT is between 108 MHz and 500 MHz the
measurement shall only be made up to 2 GHz. If the highest frequency of the internal sources of the EUT
is between 500 MHz and 1 GHz, the measurement shall only be made up to 5 GHz. If the highest
frequency of the internal sources of the EUT is above 1 GHz, the measurement shall be made up to 5
times the highest frequency or 40 GHz, whichever is less.
6.3. Test Procedure

The EUT was placed on a non-conductive table whose total height equaled 80cm. All units of
equipment forming the system under test (includes the EUT as well as connected peripherals and
associated equipment or devices) shall be arranged such that a nominal 0.1 m separation is achieved
between the neighboring units. Where the mains cable supplied by the manufacturer is longer than 1
m, the excess should be folded at the centre into a bundle no longer than 0.4 m, so that its length is
shortened to 1 m.
The EUT was set 3 meters away from the receiving antenna that was mounted on a non-conductive
mast. The antenna can move up and down between 1 to 4 meters to find out the maximum emission
level.
The turntable can rotate 360 degree to determine the position of the maximum emission level.
The initial testing identified the frequency that has the highest disturbance relative to the limit while
operating the EUT in typical modes of operation and cable positions in a test setup representative of
typical system configuration.
The identification of the frequency of highest emission with respect to the limit was found by
investigating emissions at a number of significant frequencies. The probable frequency of maximum
emission had been found and that the associated cable and EUT configuration and mode of
operation had been identified.
The frequency range above 1GHz the measuring instrument use RBW=1 MHz and VBW=3 MHz with
peak detector for peak values, and use RBW=1 MHz and VBW=10 Hz with peak detector for Average
Values.

Emission level (dBμV/m) = Antenna Factor - Amp Factor +Cable Loss + Reading
Margin (dB) = Emission Level (dBμV/m) - Limit (dBμV/m)
PASS.

7. PHOTOGRAPHS
7.1. Photos of Radiation Emission Measurement

Spurious Emission Test Setup (Below 1GHz)
Spurious Emission Test Setup (Above 1GHz)

APPENDIX A: Label Requirements
(1) Receivers associated with the operation of a licensed radio service, e.g., FM broadcast under part 73
of this chapter, land mobile operation under part 90 of this chapter, etc., shall bear the following statement
in a conspicuous location on the device:
This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device
does not cause harmful interference.
(2) A stand-alone cable input selector switch, shall bear the following statement in a conspicuous location
on the device:
This device complies with part 15 of the FCC Rules for use with cable television service.
(3) All other devices shall bear the following statement in a conspicuous location on the device:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

APPENDIX B: Warning Statement
(a) For a Class A digital device or peripheral, the instructions furnished the user shall include the following
or similar statement, placed in a prominent location in the text of the manual:
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
(b) For a Class B digital device or peripheral, the instructions furnished the user shall include the following
or similar statement, placed in a prominent location in the text of the manual:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

APPENDIX C: Photos of EUT
EUT View 1
EUT View 2

EUT View 3
EUT View 4

EUT View 5
EUT View 6

EUT View 7
EUT Housing and Board View 1




Solder Board-Component View 1





WIFI Antenna

GPS Antenna
LTE Antenna
----------------The end----------------

C6D Ai Fcc-Sdoc

Uploaded by

Copyright:

Available Formats

C6D Ai Fcc-Sdoc

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

C6D Ai Fcc-Sdoc

Uploaded by

Copyright:

Available Formats

Test Report

(Supplier’s Declaration of conformity)

Streamax Technology Co., Ltd.

MODEL No.: C6D AI

Prepared for : Streamax Technology Co., Ltd.

Prepared by : EMTEK (SHENZHEN) CO., LTD.

Report Number : ES190925017E

TRF NO. FCC15/A Page 1 of 36 Report No.: ES190925017E Ver.1.0

TRF NO. FCC15/A Page 2 of 36 Report No.: ES190925017E Ver.1.0

Applicant : Streamax Technology Co., Ltd.

Manufacturer : Streamax Technology Co., Ltd.

Model Name : C6D AI

Measurement Procedure Used:

FCC Rules and Regulations Part 15:2017 Subpart B

Date of Test : October 08,2019 to October 29, 2019

Approved & Authorized Signer :

TRF NO. FCC15/A Page 3 of 36 Report No.: ES190925017E Ver.1.0

Version Report No. Revision Data Summary

Ver.1.0 ES190925017E October 30, 2019 Original Version

TRF NO. FCC15/A Page 4 of 36 Report No.: ES190925017E Ver.1.0

Note: N/A is an abbreviation for Not Applicable.

TRF NO. FCC15/A Page 5 of 36 Report No.: ES190925017E Ver.1.0

2.1. Description of Device (EUT)

Model Number : C6D AI

Power supply : DC 12/24V for DC power

Applicant : Streamax Technology Co., Ltd.

Manufacturer : Streamax Technology Co., Ltd.

Date of Received : September 29,2019

Date of Test : October 08,2019 to October 29, 2019

TRF NO. FCC15/A Page 6 of 36 Report No.: ES190925017E Ver.1.0

DC cable 1.0 Shielded With Ferrite

Auxiliary Cable List and Details

Auxiliary Equipment List and Details

2.3. Independent Operation Modes

2.4. Test Manner

TRF NO. FCC15/A Page 7 of 36 Report No.: ES190925017E Ver.1.0

Accredited by TUV Rheinland Shenzhen 2018.03.30

Accredited by FCC, August 09, 2018

Accredited by Industry Canada, November 09, 2018

Name of Firm : EMTEK(SHENZHEN) CO., LTD.

2.6. Test Software

Radiated Emission : EMTEK(Ver.RA-03A1)-Shenzhen

2.7. Measurement Uncertainty

Test Item Uncertainty

Radiated Emission Uncertainty : 3.78dB (30M~1GHz Polarize: H)

TRF NO. FCC15/A Page 8 of 36 Report No.: ES190925017E Ver.1.0

3.1. For Power Line Conducted Emission Measurement

3.2. For Radiated Emission Measurement

TRF NO. FCC15/A Page 9 of 36 Report No.: ES190925017E Ver.1.0

4.1. Block Diagram of Test Setup

Metal ground plane

LISN: Line Impedance Stabilization Network

Frequency Limit (dBµV)

4.3. Test Procedure

All the support units are connecting to the other LISN.

The frequency range from 150 kHz to 30 MHz was sweep.

Test results were obtained from the following equation:

4.4. Measuring Results

TRF NO. FCC15/A Page 11 of 36 Report No.: ES190925017E Ver.1.0