INTRODUCTION TO ELECTRONICS AND COMMUNICATION

SUBJECT CODE:BESCK204C

MODULE-5

Analog Communication Schemes – Modern communication system scheme Information source and input transducer,
Transmitter, Channel or Medium – Hardwired and Soft wired, Noise, Receiver, Multiplexing, Types of communication
systems. Types of modulation– AM , FM, Concept of Radio wave propagation(Ground, space, sky)
Digital Modulation Schemes: Advantages of digital communication over analog communication, ASK, FSK, PSK
Radio signal transmission Multiple access techniques.

1 Introduction to Electronics and Communication (BESCK204C) KNSIT-ECE

 Communication?

 Transfer of information from one point to

other (or) Exchange of Information between
two points.
 Electronic Communication: Sending data or
Information using electronic devices. This
allows rapid transfer of goods, money and
ideas

2 Introduction to Electronics and Communication (BESCK204C) KNSIT-ECE

Need for Communication

 Speedy transmission: Requires only few seconds to communicate through electronic media due the
technology available for quick transmission
 Wide Coverage: The whole world has become a global village and communication around the globe
requires just a second
 Low Cost: Cost of an SMS is cheaper than sending a letter by post
 Exchange of feedback: Instant exchange of feedback
 24/7 accessibility: Can be accessed anytime

Message signal: The signal that consists information is called modulating signal. The modulating signal is
usually of low-frequency signal. (20 Hz – 20 KHz)

Carrier signal:
The signal which carries the information is called carrier signal. Carrier signal is a high frequency signal
which does not contains any information. The purpose of this signal is just to carry the message signal. The
range is in terms of Mega Hertz.

4.1.1 Modern Communication System scheme

General form of a basic communication system is shown in the fig.1.

Fig.1 Illustration of Basic Communication System

3 Introduction to Electronics and Communication (BESCK204C) KNSIT-ECE

 Elements of Communication System
 Information source and transducer
 Transmitter
 Channel or medium
 Noise
 Receiver
 Output transducer and final destination
A communication system transmits information from an information source (message) to a destination.
 Examples: Voice, Live scenes (video), music, written text, and e-mail.
A transducer is a device that converts a physical signal into its corresponding electrical signal and vice
versa.
Examples of input transducers: Sound - Microphone
Picture - Camera
Text - Keyboard
Temperature/Pressure - Sensor with transducer

(i) Information Source and Transducer

Message or information originates in the information source may be in the form of sound (human speech),
picture (image source), words (text). However, out of these messages, only the desired message is selected
and communicated.
Type of Signals

Signals are functions that carry information. We use signals to convey information from place to place. In
electronics, signals are mainly in the form of varying voltages. There are two types of signals.

Analog Signals Digital Signals

Analog signal is continuous and time varying Digital signal have two or more states (binary
form)
Troubleshooting is difficult. Troubleshooting is easy.
Easily affected by the noise. These are stable and less prone to noise.
Analog signals use continuous values to represent the Digital signals use discrete values to represent the
data, usually in the form of sine wave. data, usually in the form of square wave.
Accuracy may be affected by noise. Accuracy is immune from the noise.
Analog signals may be corrupted during data Digital signals are not corrupted during data
transmission. transmission.
Analog signals use more power. Digital signals use less power.
Examples: Temperature, Pressure, Flow measurements, Examples: Motor Start, Trip, etc.
etc.
Components like resistors, Capacitors, Inductors, Diodes Components like transistors, logic gates, and
are used in analog circuits. micro-controllers are used in digital circuits.

4 Introduction to Electronics and Communication (BESCK204C) KNSIT-ECE

A transducer is a device which converts one form of energy into another form. Generally, the input transducer
converts the non-electrical signal (Ex: sound signal or light signal) into an electrical signal.

For example, in case of radio-broadcasting, a microphone converts the information or massage which is in the
form of sound waves into corresponding electrical signal.

(ii) Transmitter
The base band signal (electrical form), output from the input transducer is applied to the input of the
transmitter. The transmitter section processes the signal prior to transmission. The nature of processing
depends on the type of communication system.
There are two options for processing signals prior transmission
(i) The baseband signal, which lies in the low frequency spectrum, is translated to a higher frequency
spectrum --- carrier communication system
In this process, modulation is the main function of the transmitter. In modulation, the message signal is
superimposed upon the high-frequency carrier signal. As the original message signal cannot be transmitted
over a longer distance because of their low frequency and amplitude, they are superimposed with high
frequency carrier signal.
(ii) The baseband signal is transmitted without translating it to a higher frequency spectrum --- baseband
communication system.

If the signal is to be transmitted through the space, then the transmitter will convert the electrical signals into
radio waves. If the signal is to be transmitted through the fiber optic cable then the transmitter will convert the
electrical signal into light or optical signal.

Typical Analog transmitter

Let s(t) be the baseband signal applied to the modulated stage as shown in the fig1a, to translate (modulate) it
from low to high frequency spectrum. That means, s(t) is superimposed upon the high-frequency carrier signal
c(t), which is generated by a high frequency carrier oscillator. The output of the modulated stage is called the
modulated signal, and is designated as x(t). This signal is then applied to amplifier stage. The voltage of the
modulated signal is amplified to drive the power amplifier stage. The power amplifier that amplifies the

5 Introduction to Electronics and Communication (BESCK204C) KNSIT-ECE

power of the modulated signal x(t) and thus it carries enough power to reach the receiver stage of the
communication system. Finally, the signal is passed to the transmission medium or channel.

Fig.1a Block diagram of analog transmitter section

For example, in radio broadcasting the sound signal (message signal) is converted into the electrical signal
(baseband signal), by the input transducer. Then, it is modulated with the radio frequency range carrier signals
to produce radio signals. These radio signals are transmitted through electromagnetic waves (open space),
referred to as radio waves.
Radio Frequency (RF) bands spread in the range between 30 kHz and 300 GHz. Transmission systems are
operated in the RF spectrum range and its application in communication systems is tabulated in the table-1.

Table 1: Frequency ranges and its application in communication systems

Frequency Name Frequency Range Application

Super high frequencies 3GHz-30GHz RADAR

Ultra high frequencies 300MHz-3GHz Satellite communication, cellular phones

Very high frequencies 30MHz-300MHz TV and FM

High frequencies 3MHz-30MHz Commercial short wave broadcast
Medium frequencies 300kHz-3MHz AM broadcast

Low frequencies 30kHz-300kHz Navigation, submarine communication

Very low frequencies 3kHz-30kHz Navigation, submarine communication
Voice frequencies 300Hz-3kHz Navigation ,submarine, audio
Extremely low frequencies 30Hz-300Hz Power transmission

(iii) Channel or medium

The term channel means the medium through which the message travels from the transmitter to the
receiver. The transmitted signal should have adequate power to withstand the channel noise. The channel
characteristics also impose constraints on the bandwidth.
Depending on the physical implementations, one can classify the channels in the following two groups:

a) Hardwired channels (Manmade structure)

6 Introduction to Electronics and Communication (BESCK204C) KNSIT-ECE

 Transmission lines: It is a conductive medium consisting of two or more conductors through which
electrical signal are transmitted from transmitting point to receiver point.
Example: i) Twisted pair cables used in telephony, in which two conductors are twisted together for the
purposes of improving electromagnetic compatibility.
ii) Coaxial cable used in TV transmission, to carry high-frequency electrical signals with low losses.
Waveguide: consisting of a hollow, metal tube of uniform cross-section used for transmitting electro-
magnetic waves. When signals entered the waveguides are reflected at the metallic walls and propagate at
the other end. The energy is in the form of electric field and magnetic field which are perpendicular to
each other.
Optical Fibre: consist of very thin hollow glass fibre through which signal is transmitted in the form of
light energy.
b) Soft-wired channels (no physical link between transmitter and receiver)
Natural resources which can be used as the transmission medium for signals.
Example: Air or Open space and Sea water.
The signals are transmitted in the form of electromagnetic (EM) waves also called radio waves. Radio
waves travel through open space at a speed equal to that of light (c = 3 x 108 m/s)
(iv) Noise
Noise is defined as unwanted electrical signal which do not have any useful information. Noise is a highly
undesirable part of a communication system, and has to be minimized. When noise is mixed with the
transmitted signal, it rides over it and deteriorates its waveform.

Noise calculation:
Signal to Noise Ratio (SNR) and Noise figure (F)
SNR is defined as the ratio of signal power (S) to the noise power (N), often expressed in decibels (dB).

7 Introduction to Electronics and Communication (BESCK204C) KNSIT-ECE

(v) Typical Analog Receiver
The main function of the receiver is to reproduce the original message signal. This reproduction of the
original signal is accomplished by a process known as the demodulation or detection. Demodulation is the
reverse process of modulation carried out in transmitter. Typical analog receiver section is shown in the fig.2.
The signal received by the receiver is r(t). Due to attenuation this received signal r(t) is a weak signal. A
voltage amplifier amplifies to make strong enough for further processing.

Fig.2 Block diagram of analog receiver section

Next, this signal is applied to the demodulator. In demodulation, the baseband signal is separated from the
high-frequency carrier signal. After recovering the original baseband signal s’(t), its voltage and power is
amplified before send to the final destination block.

(vi) Destination

Destination is the final stage which is used to convert an electrical message signal into its original form. For
example in radio broadcasting, the destination is a loudspeaker which works as a transducer that converts the
electrical signal to original sound signal.

4.1.2 Types of Communication Systems

 Communication Systems based on Physical Infrastructure

Based on physical infrastructure there are two types of communication systems:
Line communication systems: Uses power lines to transfer data from one point to another point. There is a
physical link, called a hardwire channel between the transmitter and the receiver inline communication
systems. Ex: Land line telephony, Cable TV
 Communication systems based on Signal specifications

A. Based on Nature of baseband or information signal

i) Analog communication systems: Exchange of information between two points through analog
signals.
Ex: Audio, video and pictures between two points using the analog signals.

8 Introduction to Electronics and Communication (BESCK204C) KNSIT-ECE

 ii) Digital communication systems: Exchange of information between two points through digital
signals.
Ex: Audio, HDTV

B. Based on Nature of the transmitted signal

i) Baseband communication system: Baseband signals are transmitted without translating (or
amplified) to higher frequencies. Ex: Land line, fax, etc
ii) Carrier communication system: The baseband signal (low frequency) is mixed with high frequency
carrier signal. Ex: Radio, voice messages and calls.

4.1.3 Multiplexing

Multiplexing is a process which allows more than one signal to be transmitted through a single channel.

In multiplexing, each baseband signals are modulated with different carrier frequencies. At the transmitter
they can be mixes and transmitted. At the receiver end, all different transmitted signals can be easily separated
by the known carrier frequencies.

Due to multiplexing it is possible to increase the number of communication channels so that more information
can be transmitted where it makes the communication system economical. The typical applications of
multiplexing are telephone, satellite communication etc.

9 Introduction to Electronics and Communication (BESCK204C) KNSIT-ECE

4.1.4 Types of Modulation

Modulation is the process in which any one of the parameters (amplitude, frequency or phase) of the high
frequency carrier signal is varied according to the instantaneous values of the low frequency message signal,
keeping other parameters constant.

Analog modulation is typically used for AM, FM radio, and short-wave broadcasting. Digital modulation
involves transmission of binary signals (0 and 1).

Amplitude Modulation (AM) is the process in which the amplitude of the carrier signal is varied according to
the instantaneous values of the message signal, where as the frequency and phase are kept constant. It is as
shown in the fig.2.

The first figure is the carrier wave, which is a high frequency signal and contains no information. Denoted as
c(t) = Ac cos(2πfct)
The next one is the modulating wave, which is the message signal; (low frequency signal) contains
information. Denoted as m(t) = Am cos(2πfmt)
10 Introduction to Electronics and Communication (BESCK204C) KNSIT-ECE
The last one is the resultant amplitude modulated wave. Mathematically, AM is denoted as

VAM = Vc sin ωc t + cos (ωc - ωm) t - cos (ωc + ωm) t

In AM, most of the transmitted power is wasted in carrier, but used for longer distance communication.
Frequency Modulation is defined as a process in which the frequency of the carrier is varied in accordance
with the instantaneous values of the message signal, where as the amplitude and phase are kept constant.

Δ f (frequency deviation)

Mathematically, FM wave is denoted as S (t) = A sin [2πfct + mf )]

Modulation index (depth of modulation) mf =
Carrier Swing = f(max) - f(min) = 2f
In FM, all the transmitted power is useful, but used for short distance communication.
Phase Modulation is defined as a process in which the phase of the carrier is varied in accordance with the
instantaneous values of the message signal, where as the amplitude and frequency are kept constant.

11 Introduction to Electronics and Communication (BESCK204C) KNSIT-ECE

Mathematical equation of PM wave will be
s(t)=Ac cos(2πfct+βcos(2πfmt))
Where, β = modulation index = Δϕ = kpAm and Δϕ is phase deviation.
Phase modulation is used in mobile communication systems.

4.2 Radio Wave Propagation

Radio waves exhibit the properties of light with the velocity 3x108 m/s. These are electromagnetic (EM)
waves that consist of electric and magnetic field components. It is traversed in nature. Radio signals can travel
from one end to another over vast distances. Since these are EM waves, they exhibit properties (like light
waves) such as reflection, refraction, diffraction, absorption, polarization and scattering.

Radio propagation is the way of transmitting radio signals in different ways:

i) Ground or surface wave
Ground waves can be used for radio communication. Ground wave transmission is very reliable
irrespective of the atmospheric conditions.

Frequency range: 30 kHz to 3 MHz

Transmission distance: 100 to 1000 km
Example: AM radio broadcast in the medium frequency band cover local areas.

ii) Space or tropo-spheric wave

In space wave (or line of sight propagation), radio waves move in the earth’s troposphere within about
12 KM over the surface of the earth. Frequency range: 3MHz to 30 MHz. Example, TV Transmission.
The space wave is made up of two components:
(a) a direct or line-of- sight wave from the transmitting to the receiving antenna and
(b) an indirect or ground-reflected wave traversing form the transmitting antenna to ground and
reflected to the receiving antenna.

iii) Sky wave

Radio waves transmitted from the transmitting antenna reach the receiving antenna after reflection
from the ionosphere (the earth’s upper atmosphere).
Sky wave is responsible for short wave transmission around the globe via successive reflections at the
ionosphere and the earth’s surface.
Ionosphere - The ionized region extending about 80 KM above the earth’s surface. In ionosphere
radiation from the sun ionizes atoms and molecules that liberate electrons and ions from molecules.
The propagation of radio wave through the ionosphere is affected by the electrons and ions. The effect
of the electrons on the propagation is much greater than that of the ions since the electronic mass is
much less than the ionic mass.
 Fig.4 Radio wave propagation

Advantages of sky wave propagation

1. It supports large distance propagation.
2. The frequency range of operation is considerably high.
3. Attenuation due to atmospheric conditions is less.
Disadvantages of sky wave propagation
1. Long-distance propagation requires large-sized antennas.
2. Due to the presence of the ionosphere near and far during night and day respectively there exist
variation in signal transmission in day and night.
Applications
Sky wave propagation is widely used in mobile and satellite communications.

4.3 Digital Modulation Schemes

In digital communications, the modulating signal consists of binary data. When it is required to transmit
digital signals, the amplitude, frequency or phase of the sinusoidal carrier is varied in accordance with the
incoming digital data.
Digital modulation schemes are classified as
i) Amplitude Shift Keying (ASK)
ii) Frequency Shift Keying (FSK)
iii) Phase Shift Keying (PSK)

ASK (Amplitude Shift Keying)

ASK represents digital data as variations in the amplitude of a carrier wave. ASK signal can generated when
the incoming binary data and the sinusoidal carrier are applied a product modulator as inputs.
FSK (Frequency Shift Keying)
In this technique digital signal is transmitted by switching between low frequency and high frequency in order
to represent 0’s and 1’s. The simplest FSK is Binary FSK (BFSK). It uses a pair of discrete frequencies to
transmit binary (0s and 1s) information.

Phase Shift Keying (PSK)

The simplest form of PSK is binary phase shift keying (BPSK). In this case, the carrier phase is shifted
between two different phases (typically 0° and 180°) depending on whether 0-bit or 1-bit is being transmitted.

For example:
0- bit: the symbol transmitted is Vc cos (2πf c t)
1- bit: the symbol transmitted is Vc cos (2πfc t +180°) = − Vc cos(2πf c t)

4.4 Radio signal Transmission

From the fig.5 the wireless transmitter accepts four different binary streams of bits (00, 10, 11 and 01) from
the application software. Further, these bits encoded on to a radio wave, known as a carrier by adjusting its
amplitude or phase. Transmitter operates in two stages. In the first stage, quadrature phase shift keying
(QPSK) modulator accepts the incoming binary bits and convert it to symbols that represents the amplitude
and the phase. Then, the symbols are passed over the analog transmitter, which generates the radio wave.
 Fig.5 Wireless communication transmitter

QPSK modulator takes two bits at a time and transmits them using a radio wave. Four different binary states
have phases of 45o, 135o, 225o, and 315o as shown in the fig.6.

Fig.6 (a) QPSK representation (b) QPSK constellation diagram

The distance of each state from the origin represents the amplitude of the transmitted wave, while angle
measured anti-clockwise from x-axis represents the phase.
Each symbol is conveniently represented by two components: in-phase (I) and quadrature (Q).
I = a cos Φ (real part)
and Q = a sin Φ (imaginary part)

Note: Radio works by transmitting and receiving electromagnetic waves. Radio signal uses specific radio frequency
AM is expressed in kilo Hertz, while FM radio is expressed in mega Hertz.

LTE Modulation scheme

LTE (Long Term Evolution) is a standard for wireless broadband communication for mobile devices
(marketed as 4G). LTE uses four modulation schemes together as given below.
i) Binary Phase Shift Keying – BPSK
ii) Quadrature Phase Shift Keying - QPSK
iii) 16 Quadrature Amplitude Modulation -16 QAM
iv) 64 Quadrature Amplitude Modulation – 64 QAM
i) BPSK sends one bit at a time using two states (0 and 1) representing phases of 0o and 180o or signal
amplitudes of +1 and -1

ii) QPSK sends two bits at a time iii) 16 - QAM sends four bits at a iv) 64 - QAM sends six bits at a
using 4 states (00, 01, 10 and 11) time using 16 states to represent time using 64 states to represent
to represent amplitude and phase amplitude and phase. amplitude and phase.
by 45o, 135o, 225o, and 315o

4.5 Multiple Access Techniques

Multiple access is a technique to provide communication service to multiple users over a single channel. It
allows multiple mobile users share the allotted spectrum in the most effective manner.
Frequency Division Multiple Access (FDMA)
Available frequency band is split into smaller frequency channels, and different channels are assigned to
different users. The carriers are separated by guard bands, which avoid the interference between the users.
Time Division Multiple Access (TDMA)
Various users can transmit at the same frequency band at different times. Every user is permitted to transmit
only in specific time slots using a common frequency band.
GSM uses a combination of both TDMA and FDMA techniques.LTE uses orthogonal FDMA techniques.

Code Division Multiple Access (CDMA)

Mobiles receive signals on the same carrier frequency and at the same time. But the signals are labeled by the
use of codes, which allows a mobile to separate its own signal from the others.
CDMA is the common platform on which 3G technologies are built.
FDD and TDD Modes
Duplexing: Allows users to send information simultaneously to the base station, while receiving information
from the base station. The wireless telephony applies duplexing technique where talking and listening is
enabled at a time.
Frequency Division Duplexing (FDD): Base station and mobile will transmit and receive at the same time, but
using different carrier frequencies. FDD uses two separate frequency bands for every user. A sufficient guard
band needs to separate the transmitting and receiving channels, so they do not interfere with one another. FDD
is suitable for radio communication systems. It uses frequency for uplink and down link.

[Down link: Base Station to mobile; Uplink: Mobile to Base Station]

Time Division Duplexing (TDD)- Base station and mobile will transmit and receive on the same carrier
frequency but at different times. Time slots could be dynamically allocated separated by a guard band. A
guard period ensures that UL and DL transmissions do not collide. TDD is more suitable for fixed wireless
systems. It uses time for uplink and down link.