Hall Ticket No: Question Paper Code :

ANIL NEERUKONDA INSTITUTE OF TECHNOLOGY & SCIENCES

(AUTONOMOUS)
II/IV B. Tech I- Semester Regular Examinations Oct – 2016
(Regulations: R15)
Digital Logic Design
(EEE)
Time: 3 hours Max Marks: 60
Answer ONE Question from each Unit
All Questions Carry Equal Marks
All parts of the question must be answered in one place only

UNIT-I
1. a) Discuss about 1′s and 2′s Complement of subtraction. 4M
b) Differentiate between binary code and BCD code. 4M

c) Convert (5064)9 into base 5 4M

(OR)

2. a) Explain about Self complementing code and gray code. 4M

b) Convert F(x)= x+y′z into canonical form. 4M

c) State and prove idempotent laws of Boolean algebra. 4M

UNIT-II
3. a) Define K Map . Name its advantages. 4M
b) Slove the function using K Map 4M
x′yz+x′yz′+xy′z′+xy′z

c) Design XNOR and XOR Gates using Universal Gates 4M

(OR)
4. a) Design Full adder and Full subtractor by using Universal Gates 6M

b) Design a logic circuit to convert BCD and gray code. 6M

MODEL PAPER 1
 UNIT-III
5. a) Design and implement 4-bit binary counter using D flipflop 6M

b) Design T Flip Flop using Logic Gates. 6M

(OR)

6.a Compare the merits and demerits between Ripple and Synchronous counter. 6M
b Explain about Shift registers 6M

UNIT-IV
7.a Explain the differences among a truth table, state table, a characteristic table and 4M
a excitation table.
b Write down the steps for the design of sequential Circuits 3M

c A sequential circuit with 2 D Flip Flops A and B , two inputs X and Y and one 5M
output Z is specified by the following next state and output equations
A(t+1)= X′Y+XB
B(t+1)= X′A+XB
Z= A
i) Draw the logic diagram of the circuit
ii) List the state table for the sequential circuit
(OR)
8.a Write a short notes on Serial Adder 3M

b Explain State Reduction Method. 3M

c A sequential circuit with 2 JK Flip Flops A and B , two inputs X and Y and one 6M
output Z . The Flip Flop input equations and circuit output equations are
JA= B′Y′+BX KA= B′XY′
JB= A′X KB= A+XY′
Z= AX′Y′+ BX′Y′
i) Draw the logic diagram of the circuit
ii) Tabulate the State table.
UNIT-V
9.a Differentiate between PLAS and PALS 4M
b Implement the following using PLA 8M
F1 (X,Y,Z) = ∑m(0,2,47)
F2 (X,Y,Z) = ∑m(3,5,6,7)

(OR)
10.a Classify and explain the types of ROM’S 4M
b Implement the following using PLA 8M
F1 (A,B,C) = ∑m(0,1,2,4)
F2 (A,B,C) = ∑m(0,5,6,7)
******
MODEL PAPER 2
Hall Ticket No: Question Paper Code :

ANIL NEERUKONDA INSTITUTE OF TECHNOLOGY & SCIENCES

(AUTONOMOUS)
II/IV B. Tech I- Semester Regular Examinations Oct - 2016
(Regulations: R15)
Electromagnetics
(EEE)
Time: 3 hours Max Marks: 60
Answer ONE Question from each Unit
All Questions Carry Equal Marks
All parts of the question must be answered in one place only

UNIT-I

1 a) Drawing necessary sketches, obtain the rectangular coordinates X,Y,Z of a (4M)

point ‘P’ in terms of its spherical coordinates r, θ, ɸ. Assume same origin for
both coordinate systems.

b) Find the total charge in a volume defined by the six planes for which (8M)
1≤ X ≤ 2 , 2 ≤ Y ≤ 3 , 3 ≤ Z ≤ 4 if D̄ = 4Xāx + 3Y²āy + 2Z³āz C/m² .

OR

2 a) Derive an expression for the electric field intensity at a point due to an infinite (7M)
sheet of charge.

b) Find Ē at P(1,1,1) caused by Four identical 3nc charges located at P1(1,1,0), (5M)
P2(-1,1,0) P3(-1,-1,0), and P4 (1,-1,0).

UNIT-II

3 a) Show that J = σ E from fundamentals. Derive the continuity equation of (7M)

current.

b) A dipole of moment P̅ = 5az nc-m is located at the origin in free space then Find (5M)
‘V’ and ‘E’ at point P (4, 20°, 0°).

OR
4 a) Derive the expression for capacitance and energy stored in a parallel plate (7M)
capacitor.

b) Charges of 3C, 2C and 1C are placed at the corners of an equilateral triangle of (5M)
side 2 meter. Find the energy needed to assemble those charges in this manner.

MODEL PAPER 1
 UNIT-III

5 a) Find the solutions of Laplace equation in one dimension using Cartesian (6M)
coordinates and Cylindrical coordinates.

b) State Biot-Savarte law with their units. A current element (6M)

Idl = 2π (0.6ax – 0.6ay) μA is situated at point (4,-2, 3)m. Find the incremental
field dH at a point (1, 3, 2)m.

OR

6 a) Find H on the axis of a circular loop of radius ‘R’ at a distance‘d’ from the (7M)
centre carrying a current of ‘I’ amperes in the counter clockwise direction.
Specialize the result to the centre of the loop.

b) In cylindrical coordinates, B = (2/r) aϕ Tesla. Determine the magnetic flux ‘ϕ’ (5M)
crossing the plane surface defined by 0.5 ≤ r ≤ 2.5 m and 0 ≤ Z ≤ 2 m.

UNIT-IV

7 a) Derive the conditions which B & H should satisfy at the interphase between (7M)
two magnetic media.

b) A 200 turn rectangular coil 0.3mX0.15m with a current of 0.5 A is in a uniform (5M)
field B = 0.2 T. Find the magnetic moment and maximum torque.

OR

8 a) Derive the expression for force between two parallel conductors of finite (8M)
length.

b) A straight thin conductor carries a steady current of 10 amperes, with positive (4M)
X-direction. There exists a magnetic field of 2 wb/m2 in a direction parallel to
the X-Y plane and making angle 300 with the X-axis. Find the magnitude and
direction of the force on a 3 meter length of conductor.

UNIT- V

9 a) Write the Maxwell’s equations for time varying fields. (6M)

b) A copper wire carries a conduction current of 1 A. determine the displacement (6M)

current in the wire at 100 MHz . Take ε = ε0 and σ = 5.8X107 mho/m

OR

10 a) Explain clearly, why the expression Curl H = J is to be modified for the magnetic field (8M)
which vary with time. Obtain the modified equation.

b) Distinguish between ‘transformer induced e.m.f’ and ‘rotational induced (4M)

e.m.f’.
MODEL PAPER 2
MODEL PAPER 3
 Hall Ticket No: Question Paper Code :

ANIL NEERUKONDA INSTITUTE OF TECHNOLOGY & SCIENCES

(AUTONOMOUS)
II/IV B. Tech I- Semester Regular Examinations Oct – 2016
(Regulations: R15)
ELECTRONIC DEVICES AND CIRCUITS
(EEE)
Time: 3 hours Max Marks: 60

Answer ONE Question from each Unit

All Questions Carry Equal Marks
All parts of the question must be answered in one place only
UNIT-I
1. a) What are the two types of capacitances across a P-N junction? Which of these is
more important in case of forward bias? (4M)

2. b) Explain the operation of half wave rectifier and derive the expression for its ripple
factor and efficiency. (8M)

(OR)
3. a) Explain the operation of a PN junction diode with the help of its energy band
diagrams. Discuss in detail the various current components in a forward biased PN
diode. (6M)
b) A 15-0-15v (rms) ideal transformer is used with a full wave rectifier circuit with
diodes having forward drop of 1v. The load is a resistance of 100 Ω & a capacitor
of 0.01F is used as a filter across the load resistance. Calculate the dc load current,
voltage & ripple factor. (6M)
UNIT-II

4. a) Distinguish between avalanche breakdown & Zener breakdown (4M)

b) With neat diagram explain the construction working characteristics of UJT. Give its
equivalent circuit. (8M)
(OR)
5. a) What is tunneling phenomenon? Draw and explain the Volt-Ampere characteristics
of Tunnel diode. (6M)

b) Write short notes on (i) varactor diode (ii) photo diode. (6M)

(OR)
6. a) With the help of current components explain the operation of NPN Transistor (6M)
b) Obtain the relation between α and β of transistors (4M)
c) A transistor has IB = 105µA and IC = 2.05µA. Find: (i) β (ii) α (iii) IE (2M)

MODEL PAPER 1
 UNIT-IV

7. a) Explain how JFET can be used as a voltage variable resistor. (4M)

b) Explain the construction, operation and characteristics of an enhancement type
MOSFET. (8M)
(OR)
8. a) Define the following terms.(i) transconductance (ii) drain resistance (iii)
amplification factor. (4M)
b) An N-channel JFET has Vp= -4.5V, IDSS = 9mA & IDS = 3mA. Determine its ‘VGS’
& ‘gm’. (4M)
c) Compare BJT and JFET. (4M)

UNIT-V

9. a) What is thermal runaway in amplifier circuits using BJTs. Show that to prevent
thermal runaway in a CE amplifier the biasing shall be such that VCE≤VCC/2. (6M)
b) Draw a voltage divider bias circuit and derive an expression for it stability factor.
(6M)
(OR)
10. a) A transistor is connected in a self bias current with IE = 5mA, VCE = 6V, VC =
8V,S=10,β= 200 & VCC = 20V. Determine the values of resistors used in it (6M)

b) Explain any two biasing techniques of JFET? (6M)

******

MODEL PAPER 2
Hall Ticket No: Question Paper Code :

ANIL NEERUKONDA INSTITUTE OF TECHNOLOGY & SCIENCES

(AUTONOMOUS)
II/IV B. Tech I- Semester Regular Examinations Oct - 2016
(Regulations: R15)
MATHEMATICS- III
(MECH, ECE, EEE, CIVIL, CHEMICAL)

Time :3hours Max Marks:60

Answer ONE Question from each Unit
All Questions Carry Equal Marks
All parts of the question must be answered in one place only
UNIT – I

1. a) Find the constants a and b so that the surface ax 2  byz  (a  2) x will be orthogonal to
the surface 4 x 2 y  z 3  4 at the point (1,  1, 2) (6)

b) Prove that Curl Curl F  grad divF   2 F (6)

(OR)

2.a) If f  x 2  y 2  z 
2 n
, find div grad f and determine n if div grad f  0 (6)

2 1
b) Prove that ,  f (r )  f (r ) 
2 11
f (r ) .
r (6)
UNIT-II

3. a) If  is a scalar point function , use stoke’s theorem to prove that Curl ( grad )  0 ,
(6)

  
b) Evaluate ( x 2  2 xy )dx  ( x 2 y  3)dy , where, C is the square formed by the lines
c (6)
x  1 and y  1

(OR)

4. a) Verify Divergence theorem for F  x 2i  yzj  yzk taken over the cube (6)
x  0, x  a; y  0, y  a; z  0, z  a
Find the area of a circle by Green’s theorem.
b) (6)
UNIT-III
5. a) Form the Partial differential equation (by eliminating the arbitrary constant a, b ) of
x  a 2   y  b2  z 2  c2
(6)

2 z 2 z 2 z
b) Solve 3  2 2  cos  x  2 y  (6)
x 2 xy y

MODEL PAPER-I 1
 (OR)

6. a)
Solve x 2  y  z  p  y 2 z  xq  z 2 x  y  . (6)

b)
Solve  D  D 1  D  2D  3 z  4  3x  6 y . (6)

UNIT-IV
7. a) u u (6)
Solve , using variable separable method , 3 2  0, u ( x, 0)  4e  x .
x y

b) A tightly stretched string with fixed end points x=0 and x= l is initially in a position (6)
x
given by y  y0 sin 3   If it is released from rest from this position, find the
 l 
displacement y( x, t ) .
(OR)
 2u 1  u

2
8. a ) Find the solution of 1-dimensional hear equation , where c is diffusivity
x 2 c 2 t

of material of the bar. (6)

b) A homogeneous rod of conducting material of length 100cm has its ends kept at zero
temperature and the temperature initially is,

 x, 0  x  50 (6)
U(x,0) = 100  x , 50  x 100 ..
UNIT-IV
9. a) a 2  x 2 if x a
Find the Fourier transform of f x    , Hence Show that
 0 if x a (6)
 sin x  x cos x 
0 x3
dx 
4

b) Verify the convolution theorem for f x   g x   e  x .

2
(6)

(OR)
10. a) Find the Fourier Sine and Cosine transform of f x   e  ax and hence deduce the
(6)
inversion formulae
b) Using finite Fourier transform, solve u  2  u given that 2

t x 2
u(0, t )  0, u( x, 0)  e x ( x  0) and u ( x, t ) is bounded where x>0, t>0. (6)

******

MODEL PAPER-I 2
Hall Ticket No: Question Paper Code :

ANIL NEERUKONDA INSTITUTE OF TECHNOLOGY & SCIENCES

(AUTONOMOUS)
II/IV B. Tech I- Semester Regular Examinations Oct - 2016
(Regulations: R15)
MATHEMATICS- III
(MECH, ECE, EEE, CIVIL, CHEMICAL)
Time :3hours Max Marks:60
Answer ONE Question from each Unit
All Questions Carry Equal Marks
All parts of the question must be answered in one place only
UNIT - I

1 . a) If the directional derivative of   ax y  by z  cz x at the point (1,1,1) has

2 2 2

x 1 y  3
maximum magnitude 15 in the direction parallel to the line   z find
2 2
the values of a,b and c. (6)

b) Prove that   ( F  G)  F (.G)  G (.F )  (G.) F  ( F .) G . (6)

(OR)

2. a) Find the angle between the surfaces x  y  z  9 and z  x  y  3 at the

2 2 2 2 2

point ( 2,-1, 2 ). (6)

b) If u  x  y  z and V  xi  y j  z k , show that div (uV )  5u .

2 2 2
(6)

UNIT-II

3. a) Find the total work done in moving a particle in a force field given by
F  3xyi  5z j  10 xk along the curve x  t 2  1 , y  2t 2 , z  t 3 from t  1 to t  2.
(6)

x 2  y 2  4, z  1.5
b) Evaluate  F.d R where F  y i  x z j  z y k is the circle
3 3
. (6)
c

(OR)

 xy  y dx  x dy where C is bounded by

2 2
3. a) Verify Green’s theorem for
C

y  x and y  x . 2
(6)

 F .ds, where F  x i  y 3 j  z 3 k , and S is the

3
b) Use divergence theorem to evaluate
S

surface of the sphere x  y  z  a .

2 2 2 2
(6)

MODEL PAPER-II 1
 UNIT-III
5. a) Form the partial differential equation from F x  y  z , x  y  z  0 .
2 2 2
  (6)
b) Solve D  DD  6D  cos (2 x  y) .
2 ' '2
(6)

(OR)

6. a) Solve x( y  z ) p  y( z  x )q  z ( x  y )  0 .
2 2 2 2 2 2
(6)

2 x y
b) Solve ( D  D  1) ( D  D  2) z  e
' '
. (6)

UNIT-IV
u u x
7. a) Solve the equation 3 2  0, u( x,0)  4e . (6)
x y
u  2 u
b) Solve the equation  with boundary conditions
t x 2
u( x,0)  3 sin nx, u(0, t )  0 and u(1, t )  0, where 0  x  1, t  0 . . (6)

(OR)

2 y 2  y
2
8. a) Solve the completely equation  c , representing the vibrations of a
t 2 x 2

string of length l , fixed at both ends, given that

y( x,0)
y(0, t )  0 ; y(l , t )  0 ; y( x,0)  f ( x) and  0, 0  x  l. (6)
t
b) Find the solutions of Laplace’s equation in polar coordinates. (6)

UNIT-V

cos x
x
 ax
9. a) Find the Fourier cosine transform of e . Hence evaluate dx. (6)
0
2
 a2
b) Using the Fourier integral representation, show that

sin  cos x 
0

d 
2
when 0  x  1. (6)

(OR)

dt 
10. a) Using Parseval’s identities, prove that  (a
0
2 2
2 2

 t ) (b  t ) 2ab(a  b)
(6)

u  2 u
b) Using finite Fourier transform, solve  given u(0, t )  0 , u(4, t )  0 and
t x 2
u( x,0)  2 x where 0  x  4, t  0. (6)

******

MODEL PAPER-II 2
 Hall Ticket No: Question Paper Code :

ANIL NEERUKONDA INSTITUTE OF TECHNOLOGY & SCIENCES

(AUTONOMOUS)
II/IV B. Tech I- Semester Regular Examinations Oct – 2016
(Regulations: R15)
ENGINEERING MECHANICS & STRENGTH OF MATERIALS
(EEE)
Time: 3 hours Max Marks: 60
Answer ONE Question from each Unit
All Questions Carry Equal Marks
All parts of the question must be answered in one place only
Unit - I

1. (a) State and prove the Varignons theorem (5M)

(b) Referring to Fig. 1 below, determine the least value of the force P to cause the motion to
impend rightward. The coefficient of friction under each block is 0.2 and assume the pulley
to be frictionless. (7M)

Fig.1

(OR)

2. (a) Determine the magnitude of F1 and F2 for forces shown in fig. 2, which are in
equilibrium. . (5M)

(b) Two identical rollers each of weight 100N are supported by an inclined plane and a
vertical wall as shown in fig.3. Assuming smooth surfaces find the reactions induced at
A,B & C. (7M)

MODEL PAPER 1
 Fig. 2
Fig. 3

UNIT - II

3. (a) Determine the moment of Inertial of the C-Section shown in Fig.4 about its centroidal axis.
All dimensions are in mm (8M)

(b) Determine the coordinates of centroid of the shaded area as shown in Fig. 5, if the area
removed is semicircular. All dimensions are in mm (4M)

Fig.5
Fig. 4

(OR)

4. (a) State and prove Parallel axis theorm. (4M)

(b) Find the centroid for the following composite area shown in Fig. 6, with respect to X and
Y axes .All dimensions are in mm. (8M)

MODEL PAPER 2
 Fig. 6

UNIT – III

5. (a) Show that the trajectory of a projectile is parabola and derive an expression for maximum
height ; time of flight and range (6M)

(b) A car of mass 150 kg is travelling on a horizontal track at 36 kmph . Determine the time
required to stop the car . The coefficient of friction between road and tyres is 0.45 , Use
impulse momentum method. (6M)

(OR)

6. (a) Explain D’Alemberts Principle and work energy theorem. (6M)

(b) The motion of a particle is defined by the relation x= t3-12t2+36t+30 where ‘x’ is
expressed in meters, t in seconds determine the time, position and acceleration when
velocity v=0 (6M)

UNIT - IV

7. (a) Draw stress-strain curve for ductile material. (3M)

(b) A Beam of 20m span is simply supported over a length of 12m. It has an over-hang of
3m to the right support and an over-hang of 5m to its left support. The beam carries a
UDL of 6kN/m over its entire span and point loads of 30kN and 50kN at the extremes of
left and right portions of overhang respectively. Draw SF and BM diagrams by indicating
the values at the salient points on it. (9M)

(OR)

8. (a) Explain the various types of beams and loads with sketches. (5M)

(b) A member ABCD is subjected to point loads P1, P2, P3 & P4 as shown in fig. 7. Calculate
the Force P3 necessary for equilibrium if P1=120KN, P2=220KN & P4=160KN.

MODEL PAPER 3
 Determine also the net change in length of the member. Take E=2X105N/mm2. (7M)

Fig. 7

UNIT -- V

9. a) A hollow shaft of diameter ratio 3/8 is to transmit 375 KW power at 100 rpm. The
maximum torque being 20% greater than the mean torque. The shear stress not to
exceed 60 N/mm2 and angle of twist in a length of 4m not to exceed 20. Calculate its
external and internal diameters which would satisfy both the above conditions. Assume
modulus of rigidity, 85 GPa. (8M)

b) A rectangular beam of 200mm deep and 300mm wide is simple supported over a span
of 8m .What is the intensity of UDL the beam has to carry over its whole span if the
bending stress in the material is not to exceed 120 MPa (4M)

(OR)

10. a) Derive the flexure formulae with assumptions. (8M)

b). A solid shaft 10cm diameter and 4meters in length is subjected to twisting moment
which produces maximum shear stress of 60MPa, Determine the angle of twist in
degrees. (4M)

******

MODEL PAPER 4
 Hall Ticket No: Question Paper Code :

ANIL NEERUKONDA INSTITUTE OF TECHNOLOGY & SCIENCES

(AUTONOMOUS)
II/IV B. Tech I- Semester Regular Examinations Oct – 2016
(Regulations: R15)
Network Theory
(EEE)
Time: 3 hours Max Marks: 60
Answer ONE Question from each Unit
All Questions Carry Equal Marks
All parts of the question must be answered in one place only
UNIT-I

1. a)Find Mesh Currents in the given circuit (6M)

b)Find Node Voltages in the given circuit (6M)

(OR)

2. a) Find Thevenin’s equivalent for the circuit across A and B terminals

(6M)

MODEL PAPER 1
 b) Find Io using Superposition Theorem (6M)

UNIT-II
3. a) Find Y-parameters for the given network (6M)

b. Find h- parameters for the network shown (6M)

(OR)

4. a) A coil having an inductance of 100mH is magnetically coupled to another coil having

inductance of 900mH. The coefficient of coupling between coils is 0.45. Calculate equivalent
inductance if two coils are connected in (6 M)
(i) Series Aiding (ii) Series Opposing (iii) Parallel Aiding (iv) Parallel Opposing

b) Verify RECIPROCITY THEOREM for the given network (6 M)

MODEL PAPER 2
 UNIT-III

5. a) The switch is initially opened for a long time. At t=0, the switch is closed. Find the expression
for i(t) for t>0 in time domain. (6 M)

b) The switch is kept at position 1 and steady state condition is reached. At t=0, switch is moved
to position 2. Find the expression for i(t) in Laplace domain. (6M)

(OR)
6. a) Derive the expression for Transient Response of Source Drive Series R-L circuit with DC
excitation (6 M)
b) The switch is closed at t=0. Find value of I, di/dt and d2i/dt2 at t=0+ (6 M)

MODEL PAPER 3
 UNIT-IV
7. a)Define the following
(i) Resonant Frequency (ii) Quality Factor (iii) Bandwidth (iv) Selectivity (4 M)
b)Prove that resonant frequency is geometric mean of two half power frequencies (4 M)
c) The parameters of a parallel RLC excited by current source are R=40Ω, L=2mH and C=3μF.
Determine resonant frequency, quality factor, and bandwidth and cut-off frequencies.
(4 M)

(OR)

8. a) Derive the relationship between Line and Phase Voltage and Current in 3-phase Star
Connected system. (6 M)
b) A 3-phase balanced system supplies 110V to a Delta connected load whose phase impedances
are equal to (3.54+j3.54) Ω. Determine line currents (6 M)

UNIT-V
9. a) Find duality for the given circuit (6 M)

MODEL PAPER 4
 b) Find First and Second CAUR forms of the given function
(𝑠+1)(𝑠+3)
(6 M)
𝑠(𝑠+2)

(OR)
10. a) Define the following
(i) Graph (ii) Degree of Node (iii) Tree (iv) Twig (v) Link (vi) Co-tree (6 M)
b) For the oriented graph shown, obtain Basic Cut set Matrix (6 M)

*******

MODEL PAPER 5