Instruction Manual

Microsoft® and Windows® are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
MELDAS is a registered trademark of Mitsubishi Electric Corporation.

Other company and product names that appear in this manual are trademarks or registered
trademarks of the respective companies.
Introduction
This manual is referred to when using the MITSUBISHI CNC 700/70 Series.
This manual explains how to operate, run and set up this NC unit. Read this manual
thoroughly before using the NC unit. To safely use this NC unit, thoroughly study the
"Precautions for Safety" on the next page before use.
Details described in this manual
CAUTION
For items described as "Restrictions" or "Usable State" in this manual, the instruction manual
issued by the machine tool builder takes precedence over this manual.
Items not described in this manual must be interpreted as "not possible".
This manual is written on the assumption that all option functions are added. Confirm with the
specifications issued by the machine tool builder before starting use.
Refer to the Instruction Manual issued by each machine tool builder for details on each
machine tool.
Some screens and functions may differ depending on the NC system (or its version), and
some functions may not be possible. Please confirm the specifications before use.
Refer to the following documents.

MITSUBISHI CNC 700/70 Series Programming Manual (Machining Center System) ....IB-1500072
MITSUBISHI CNC 700/70 Series Programming Manual (Lathe System)........................IB-1500057
Precautions for Safety
Always read the specifications issued by the machine tool builder, this manual, related
manuals and attached documents before installation, operation, programming, maintenance
or inspection to ensure correct use.
Understand this numerical controller, safety items and cautions before using the unit.
This manual ranks the safety precautions into "DANGER", "WARNING" and "CAUTION".
When the user may be subject to imminent fatalities or major

DANGER injuries if handling is mistaken.
When the user may be subject to fatalities or major injuries if

WARNING
handling is mistaken.
When the user may be subject to bodily injury or when physical

CAUTION damage may occur if handling is mistaken.
Note that even items ranked as " CAUTION", may lead to major results depending on the
situation. In any case, important information that must always be observed is described.
DANGER
Not applicable in this manual.
WARNING
Not applicable in this manual.
CAUTION
1. Items related to product and manual
For items described as "Restrictions" or "Usable State" in this manual, the instruction
manual issued by the machine tool builder takes precedence over this manual.
Items not described in this manual must be interpreted as "not possible".
This manual is written on the assumption that all option functions are added. Confirm
with the specifications issued by the machine tool builder before starting use.
Refer to the Instruction Manual issued by each machine tool builder for details on
each machine tool.
Some screens and functions may differ depending on the NC system (or its version),
and some functions may not be possible. Please confirm the specifications before
use.
(Continued on next page)
CAUTION
2. Items related to installation and assembly
Ground the signal cables to ensure stable system operation. Also ground the NC unit
main frame, power distribution panel and machine to one point, so they all have the
same potential.
3. Items related to preparation before use

Always set the stored stroke limit. Failure to set this could result in collision with the
machine end.
Always turn the power OFF before connecting/disconnecting the I/O device cable.
Failure to do so could damage the I/O device and NC unit.
4. Items related to screen operation

If the tool compensation amount or workpiece coordinate system offset amount is
changed during automatic operation (including during single block stop), the changes
will be valid from the command in next block or after several subsequent blocks.
All of the various data in the NC memory is erased when formatting. Be sure to use
the transfer function to transfer all necessary data to another storage device before
formatting.
Even if the tool compensation amount write command, parameter write command or
variable data write command is executed with graphic check, the data will be actually
written in, and the original data will be overwritten.
Pay close attention to the sequence operation when carrying out forced data
setting (forced output) in the I/F diagnosis screen during machine
operation.
To prevent influence from data omission and data transformation in the communication
circuit, always verify the data after inputting and outputting machining programs.
Do not change setup parameters without prior approval from the machine tool builder.
5. Items related to programming

Because of key chattering, etc., during editing, "NO NOS. FOLLOWING G" commands
become a "G00" operation during running.
" ; ", "EOB", "%", and "EOR" are symbols used for explanation. The actual codes for
ISO are "CR, LF" ("LF") and "%".
The programs created on the Edit screen are stored in the NC memory in a "CR, LF"
format, however, the programs created with external devices such as the FD or
RS-232C may be stored in an "LF" format.
The actual codes for EIA are "EOB (End of Block)" and "EOR (End of Record)".
Do not change the fixed cycle program without prior approval from the machine tool
builder.
CAUTION
6. Items related to operation

Stay out of the moveable range of the machine during automatic operation. During
rotation, keep hands, feet and face away from the spindle.
Carry out dry operation before actually machining, and confirm the machining program,
tool offset and workpiece coordinate system offset.
If the operation start position is set from a block in the program and the program is
started, the program before the set block is not executed. If there are coordinate
system shift commands or M, S, T, and B commands before the block set as the
starting position, carry out the required commands using the MDI, etc. There is a
danger of interference with the machine if the operation is started from the set starting
position block without carrying out these operations.
Program so the mirror image function is turned ON/OFF at the mirror image center.
The mirror image center will deviate if the function is turned ON/OFF at a position
other than the mirror image center.
7. Items related to faults and abnormalities

If the battery low warning is issued, save the machining programs, tool data and
parameters in an input/output device, and then replace the battery. When the battery
alarm is issued, the machining programs, tool data and parameters may be destroyed.
Reload the data after replacing the battery.
If the axis overruns or emits an abnormal noise, immediately press the emergency
stop button and stop the axis movement.
CAUTION
8. Items related to maintenance

Incorrect connections may damage the devices, so connect the cables to the
specified connectors.
Do not apply voltages other than those indicated according to specification on the
connector. Doing so may lead to destruction or damage.
Do not connect or disconnect the connection cables between each unit while the
power is ON.
Do not connect or disconnect the PCBs while the power is ON.
Do not connect the cable by pulling on the cable wire.
Do not short circuit, charge, overheat, incinerate or disassemble the battery.
Dispose the spent battery according to local laws.
Dispose the spent cooling fan according to local laws.
Do not replace the control unit while the power is ON.
Do not replace the operation panel I/O unit while the power is ON.
Do not replace the control section power supply PCB while the power is ON.
Do not replace the expansion PCB while the power is ON.
Do not replace the memory cassette while the power is ON.
Do not replace the cooling fan while the power is ON.
Do not replace the battery while the power is ON.
Be careful that metal cutting chips, etc., do not come into contact with the connector
contacts of the memory cassette.
Do not replace the high-speed program server unit while the power is ON.
Contents
I. SCREEN OPERATIONS
1. Operating the Setting and Display Unit ........................................................................................1

1.1 Setting Display Unit Appearance ................................................................................................1
1.2 Screen Configuration ..................................................................................................................4
1.2.1 Operation Mode ...................................................................................................................5
1.2.2 MDI Status ...........................................................................................................................5
1.2.3 Operation Status ..................................................................................................................6
1.2.4 Alarms/Warnings..................................................................................................................6
1.2.5 Operation Messages ............................................................................................................6
1.3 Screen Transition Diagram .........................................................................................................7
1.4 Screen Selection Procedure .......................................................................................................8
1.5 Setting Data ................................................................................................................................9
1.5.1 Setting Numerals and Alphabetic Characters ......................................................................9
1.5.2 Inputting Operations...........................................................................................................11
1.6 Operating the Screen ................................................................................................................13
1.6.1 Changing the Displayed Part System ................................................................................13
1.6.2 Changing the Menu............................................................................................................13
1.6.3 Types of Menus..................................................................................................................13
1.7 Menu List...................................................................................................................................14
1.7.1 Displaying the Menu Function Outline ...............................................................................17
1.7.2 Directly Moving to the Menu Function................................................................................17
1.7.3 Moving the cursor...............................................................................................................18
1.8 Guidance Function ....................................................................................................................20
1.8.1 Parameter Guidance ..........................................................................................................20
1.8.2 Alarm Guidance .................................................................................................................25
1.9 Touch Panel Functions [700 series only] ..................................................................................28
1.9.1 Basic Operation..................................................................................................................28
1.9.2 Menu List............................................................................................................................30
1.9.3 Operation/Parameter Guidance .........................................................................................31
1.10 Touch Panel S/W Key .............................................................................................................32
1.10.1 Operation Method ............................................................................................................34
1.11 Screen Saver (Backlight OFF) Function .................................................................................36
1.11.1 Backlight OFF ..................................................................................................................36
1.11.2 Backlight ON ....................................................................................................................37
2. Monitor Screens ............................................................................................................................38
2.1 Screen Configuration ................................................................................................................38
2.1.1 <Auto/MDI> and <Manual> Counter Display .....................................................................44
2.1.2 Changing Between <Auto/MDI> and <Manual>.................................................................44
2.2 Operation Search ......................................................................................................................45
2.2.1 Executing an Operation Search .........................................................................................47
2.2.2 Changing Whether to Show or Hide the Comment Field ...................................................49
2.2.3 Changing the Sorting Method ............................................................................................50
2.3 Restart Search ..........................................................................................................................51
2.3.1 Main Screen .......................................................................................................................53
2.3.2 Top Search Screen ............................................................................................................55
2.3.3 File Setting Screen.............................................................................................................56
2.3.4 MSTB History Screen.........................................................................................................57
2.3.5 Operation Sequence for Program Restart..........................................................................58
2.3.6 Executing Restart Search (Restart Type 1) .......................................................................61
-i-
2.3.7 Executing Restart Search (Restart Type 2) .......................................................................62
2.3.8 Changing the Device..........................................................................................................66
2.3.9 Changing the Directory with the Main Screen....................................................................66
2.3.10 Returning to the Restart Position .....................................................................................67
2.3.11 Executing the MSTB Commands .....................................................................................69
2.4 Program Edit .............................................................................................................................70
2.5 Trace .........................................................................................................................................71
2.5.1 Displaying the Machine Position Trace ..............................................................................74
2.5.2 Canceling the Machine Position Trace...............................................................................75
2.5.3 Displaying the Machine Position of the Tool Center Point Trace .......................................75
2.5.4 Canceling the Machine Position of the Tool Center Point Trace........................................75
2.5.5 Changing the Display Range .............................................................................................76
2.5.6 Changing the Display Mode ...............................................................................................79
2.5.7 Changing the Display Angle...............................................................................................80
2.5.8 Switching the Full-screen Display Mode ............................................................................81
2.5.9 Precautions for Tracing ......................................................................................................81
2.6 Program Check (2D) .................................................................................................................82
2.7 Program Check (3D) [700 series only] ......................................................................................83
2.8 Counter All-axis Display ............................................................................................................84
2.9 Tool Compensation Amount......................................................................................................86
2.10 Workpiece Coordinate System Compensation .......................................................................89
2.11 Counter Set .............................................................................................................................90
2.12 Origin Set, Origin Cancel ........................................................................................................92
2.13 Manual Numerical Value Command .......................................................................................94
2.14 Modal Display..........................................................................................................................96
2.15 Program Tree Display .............................................................................................................99
2.16 Integrated Time Display ........................................................................................................100
2.16.1 Setting the Integrated Time............................................................................................102
2.16.2 Setting the Time Display Selection ................................................................................103
2.17 Common Variables................................................................................................................104
2.17.1 Setting Common Variables ............................................................................................106
2.17.2 Copying/Pasting Common Variables .............................................................................107
2.17.3 Erasing Common Variables ...........................................................................................108
2.18 Local Variables .....................................................................................................................109
2.18.1 Displaying the Arbitrary Local Variables ........................................................................111
2.19 Buffer Correction ...................................................................................................................112
2.20 PLC Switch Function.............................................................................................................115
2.20.1 Turning PLC Switches ON/OFF .....................................................................................116
2.21 Verify Stop.............................................................................................................................117
2.22 Load Meter Display ...............................................................................................................121
2.23 Spindle, Standby Display ......................................................................................................122
2.24 Tool Center Coordinate Display ............................................................................................123
2.25 All Spindles' Rotation Speed Display ....................................................................................125
3. Setup Screen ...............................................................................................................................126
3.1 Screen Configuration ..............................................................................................................126
3.2 Tool Compensation Amount....................................................................................................128
3.2.1 Tool Compensation Amount (M system) ..........................................................................128
3.2.1.1 Setting the Tool Compensation Data ........................................................................132
3.2.1.2 Erasing the Tool Compensation Data .......................................................................134
3.2.1.3 Copying/Pasting the Tool Compensation Data .........................................................135
3.2.2 Tool Compensation Amount (L system)...........................................................................136
3.2.2.1 Wear Data .................................................................................................................136
3.2.2.2 Tool Length Data.......................................................................................................139
3.2.2.3 Tool Nose Data .........................................................................................................141
- ii -
3.2.2.4 Operation Method .....................................................................................................144
3.3 Tool Measurement ..................................................................................................................148
3.3.1 Tool Measurement (M system) ........................................................................................148
3.3.2 Tool Measurement (L system) .........................................................................................154
3.4 Tool Registration .....................................................................................................................165
3.4.1 Registering a Tool in the Magazine Pot ...........................................................................167
3.4.2 Setting the PLC Command ..............................................................................................168
3.4.3 Setting/Erasing the Tool No. of Spindle/Standby Tools ...................................................168
3.4.4 Erasing the Tool Registration Data ..................................................................................169
3.5 Tool Life Management ............................................................................................................170
3.5.1 Displaying the Group List .................................................................................................172
3.5.2 Displaying the Life Management Data in Group Units (M system)...................................176
3.5.3 Displaying the Life Management Data (L system: Tool life management I) .....................184
3.5.4 Displaying the Tool Life Management Data in Group Units (L system: Tool life
Management II) ................................................................................................................187
3.6 Workpiece Coordinate System Offset .....................................................................................193
3.6.1 Setting the Coordinate System Offset..............................................................................195
3.6.2 Erasing the Coordinate System Offset Amount ...............................................................196
3.6.3 Setting the Workpiece Coordinate Origin.........................................................................196
3.6.4 Changing the Coordinate System Display .......................................................................197
3.7 Workpiece Measurement ........................................................................................................198
3.7.1 Workpiece Measurement (M system) ..............................................................................198
3.7.1.1 Carrying Out Surface Measurement..........................................................................202
3.7.1.2 Carrying Out Hole Measurement...............................................................................203
3.7.1.3 Carrying Out Width Measurement.............................................................................205
3.7.1.4 Carrying Out Rotation Measurement.........................................................................207
3.7.1.5 Performing Automatic Recontact When Contacting the Workpiece ..........................211
3.7.2 Workpiece Measurement (L system) ...............................................................................212
3.8 User Parameters .....................................................................................................................219
3.8.1 Selecting the Parameter Number.....................................................................................221
3.8.2 Setting the Parameters ....................................................................................................221
3.8.3 Copying/Pasting Parameters ...........................................................................................222
3.8.4 Parameter Configuration ..................................................................................................224
3.8.5 Echoback .........................................................................................................................225
3.8.6 Ethernet Parameter Password .........................................................................................225
3.8.7 Machine Parameter Password Setting Method................................................................226
3.8.8 Parameter List..................................................................................................................227
3.8.8.1 Process Parameters..................................................................................................227
3.8.8.2 Fixed Cycle ...............................................................................................................232
3.8.8.3 Control Parameters ...................................................................................................233
3.8.8.4 Operation Parameters ...............................................................................................236
3.8.8.5 I/O Parameters ..........................................................................................................238
3.8.8.6 Ethernet Parameters .................................................................................................241
3.8.8.7 Computer Link Parameters .......................................................................................243
3.8.8.8 Subprogram Storage Destination Parameters ..........................................................245
3.8.8.9 Axis Parameters ........................................................................................................246
3.8.8.10 Barrier Data (For L system only) .............................................................................248
3.8.8.11 High Accuracy Parameters......................................................................................249
3.8.8.12 High-accuracy Axis Parameters ..............................................................................254
3.9 MDI Program Editing...............................................................................................................255
3.10 Counter Setting .....................................................................................................................256
3.11 Manual Numerical Value Commands....................................................................................257
3.12 T Code List............................................................................................................................258
3.13 Pallet Program Registration [700 series only] .......................................................................260
- iii -
3.13.1 Standard Pallet Registration ..........................................................................................261
3.13.2 Pallet List Screen ...........................................................................................................263
3.13.3 Pallet Details Screen......................................................................................................265
4. Edit Screen ..................................................................................................................................269
4.1 Screen Configuration ..............................................................................................................269
4.2 Program Editing ......................................................................................................................271
4.2.1 Creating a New Machining Program ................................................................................274
4.2.2 Editing a Machining Program ...........................................................................................275
4.2.3 Editing MDI Program........................................................................................................276
4.2.4 Registering MDI Program in NC Memory.........................................................................276
4.2.5 Deleting a File ..................................................................................................................277
4.2.6 Editing Operations............................................................................................................277
4.2.7 Changing the Display .......................................................................................................278
4.2.8 Displaying an Arbitrary Line .............................................................................................279
4.2.9 Rewriting Data..................................................................................................................280
4.2.10 Inserting Data.................................................................................................................281
4.2.11 Deleting Data .................................................................................................................282
4.2.12 Searching for Character Strings.....................................................................................284
4.2.13 Replacing Character Strings ..........................................................................................286
4.2.14 Copying/Pasting Data ....................................................................................................287
4.2.15 Undoing Program Changes............................................................................................288
4.2.16 Correcting/Displaying Input Mistakes [700 series only]..................................................289
4.2.17 Adding Sequence No. (N No.) Automatically .................................................................295
4.2.18 G Code Guidance ..........................................................................................................298
4.2.19 Playback Editing.............................................................................................................301
4.3 Program Check (2D) ...............................................................................................................306
4.3.1 Checking Continuously ....................................................................................................309
4.3.2 Checking One Block at a Time.........................................................................................311
4.3.3 Canceling the Program Check .........................................................................................312
4.3.4 Drawing during a Program Check ....................................................................................312
4.3.5 Changing the Display Range ...........................................................................................313
4.3.6 Changing the Display Mode .............................................................................................316
4.3.7 Changing the Display Angle.............................................................................................317
4.3.8 Switching to Full-screen Display Mode ............................................................................318
4.3.9 Availability of Check Mode with Other Functions .............................................................319
4.3.10 Handling of Variable Commands, Parameter Input by Program, and Compensation
Data Input by Program .....................................................................................................320
4.3.11 Notes for Program Check (2D).......................................................................................321
4.4 Program Check (3D) [700 series only] ....................................................................................323
4.4.1 Checking Continuously ....................................................................................................326
4.4.2 Checking One Block at a Time.........................................................................................327
4.4.3 Canceling the Program Check .........................................................................................327
4.4.4 Enlarging and Reducing the Workpiece Shape ...............................................................328
4.4.5 Moving the Workpiece Shape ..........................................................................................328
4.4.6 Rotating the Workpiece Shape ........................................................................................328
4.4.7 Performing an Interference Check ...................................................................................329
4.4.8 Switching to Full-screen Display Mode ............................................................................329
4.4.9 Setting the Workpiece Shape...........................................................................................330
4.4.10 Setting the Tool Shape...................................................................................................335
4.4.11 Availability of Check Mode with Other Functions ...........................................................340
4.4.12 Handling of Variable Commands, Parameter Input by Program, and Compensation
Data Input by Program .....................................................................................................340
4.4.13 Notes for Program Check (3D).......................................................................................340
4.5 Program Input/Output..............................................................................................................343
- iv -
4.5.1 Changing the Valid Area ..................................................................................................346
4.5.2 Selecting a Device, Directory, and File ............................................................................347
4.5.3 Transferring a File ............................................................................................................351
4.5.4 Comparing Files (Compare).............................................................................................353
4.5.5 Erasing a File ...................................................................................................................354
4.5.6 Changing a File Name (Rename) ....................................................................................355
4.5.7 Creating a Directory .........................................................................................................356
4.5.8 Merging a File ..................................................................................................................357
4.5.9 Formatting an External Device.........................................................................................358
4.5.10 List of File Names ..........................................................................................................358
4.5.11 Edit Lock B and C ..........................................................................................................359
4.5.12 Program Display Lock C ................................................................................................360
4.5.13 Data Protect Keys ..........................................................................................................361
4.5.14 Sharing Machining Data.................................................................................................362
5. Diagnosis Screens......................................................................................................................365
5.1 System Configuration Screen .................................................................................................365
5.2 Option Display Screen ............................................................................................................368
5.3 I/F Diagnosis Screen...............................................................................................................369
5.3.1 Displaying the PLC Device Data ......................................................................................372
5.3.2 Carrying Out Modal Output ..............................................................................................373
5.3.3 Carrying Out One-shot Output .........................................................................................374
5.4 Drive Monitor Screen ..............................................................................................................375
5.4.1 Servo Axis Unit Display Items ..........................................................................................377
5.4.2 Spindle Unit Display Items ...............................................................................................380
5.4.3 Display Items for the Power Supply Unit..........................................................................389
5.4.4 Display Items for the Auxiliary Axis Unit [700 series only] ...............................................391
5.4.5 Display Items for the Synchronous Error .........................................................................393
5.4.6 Clearing the Alarm History ...............................................................................................394
5.5 NC Memory Diagnosis Screen (NC Memory Diagn Screen) ..................................................395
5.5.1 Writing/Reading the Data Using the NC Data Designation ..............................................397
5.6 Alarm Screen ..........................................................................................................................398
5.6.1 Alarm History....................................................................................................................400
5.7 Self Diagnosis Screen.............................................................................................................402
5.8 Data Sampling Screen ............................................................................................................406
5.8.1 Executing NC Data Sampling...........................................................................................411
5.8.2 Outputting Sampling Data ................................................................................................412
5.9 Anshin-net Screen...................................................................................................................414
5.9.1 Message Display Screen .................................................................................................414
5.9.2 Anshin-net Parameter 1, 2 Screen...................................................................................416
5.9.3 Operation Method ............................................................................................................417
5.9.4 Sharing Machining Data...................................................................................................418
5.10 Machine Tool Builder Network System (MTB net) Screen....................................................419
5.10.1 Message Display Screen ...............................................................................................419
5.10.2 MTB Net Parameter 1, 2 Screen....................................................................................421
5.10.3 Operation Method ..........................................................................................................422
6. Maintenance Screens .................................................................................................................423
6.1 Parameter Screens .................................................................................................................425
6.1.1 Changing the Parameter Display .....................................................................................430
6.1.2 Setting the Parameters ....................................................................................................431
6.1.3 Copying/Pasting Parameters ...........................................................................................433
6.1.4 User Parameters ..............................................................................................................435
6.1.5 Echo Back ........................................................................................................................436
6.2 Input/Output Screen ................................................................................................................437
-v-
6.2.1 Changing the Valid Area ..................................................................................................440
6.2.2 Selecting a Device, Directory and File .............................................................................441
6.2.3 Transferring a File ............................................................................................................448
6.2.4 Comparing Files (Compare).............................................................................................450
6.2.5 Erasing a File ...................................................................................................................451
6.2.6 Changing a File Name (Rename) ....................................................................................451
6.2.7 Creating a Directory .........................................................................................................452
6.2.8 Merging a File ..................................................................................................................453
6.2.9 Formatting an External Device.........................................................................................454
6.2.10 List of File Names ..........................................................................................................454
6.2.11 Edit Lock B and C ..........................................................................................................463
6.2.12 Data Protect Keys ..........................................................................................................464
6.2.13 Sharing Machining Data.................................................................................................466
6.3 All Backup Screen...................................................................................................................469
6.3.1 Performing a Backup Operation.......................................................................................471
6.3.2 Performing a Restore Operation ......................................................................................471
6.4 System Setup Screen .............................................................................................................472
6.4.1 Preparation for Spindle Parameter Setting ......................................................................474
6.4.2 Writing Initial Parameters .................................................................................................475
6.4.3 Writing Sample PLC Ladders...........................................................................................476
6.5 Adjust S-analog Screen ..........................................................................................................477
6.5.1 Adjustment Preparations..................................................................................................479
6.5.2 Performing Automatic Adjustments..................................................................................479
6.5.3 Performing Manual Adjustments ......................................................................................480
6.6 Absolute Position Setting Screen............................................................................................482
6.6.1 Selecting the Axis.............................................................................................................484
6.6.2 Carrying Out Dogless-type Zero Point Initialization .........................................................485
6.6.3 Carrying Out Dog-type Zero Point Initialization................................................................493
6.6.4 Precautions ......................................................................................................................493
6.7 Auxiliary Axis Test Screen [700 series only] ...........................................................................496
6.7.1 Preparation.......................................................................................................................499
6.7.2 Selecting a Device, Directory and File .............................................................................500
6.7.3 Test Operation .................................................................................................................504
6.7.4 Precaution ........................................................................................................................504
6.8 Diagnosis Data Collection Setting Screen ..............................................................................505
6.8.1 Performing a Data Collection Operation ..........................................................................507
6.8.2 Stopping a Data Collection Operation..............................................................................507
6.8.3 Clearing a Collected Data ................................................................................................507
II. MACHINE OPERATIONS
1. Operation State ...............................................................................................................................2

1.1 Operation State Correlation Diagram..........................................................................................2
1.2 Power OFF..................................................................................................................................2
1.3 Operations Not Ready.................................................................................................................3
1.4 Operations Ready .......................................................................................................................3
1.4.1 Reset....................................................................................................................................3
1.4.2 Automatic Operation in Progress .........................................................................................3
1.4.3 Automatic Operation Pause .................................................................................................3
1.4.4 Automatic Operation Stop ....................................................................................................3
2. Indicator Lamps ..............................................................................................................................4
- vi -
2.1 Control Unit Ready......................................................................................................................4
2.2 In Automatic Operation ...............................................................................................................4
2.3 Automatic Operation Start Busy..................................................................................................4
2.4 Automatic Operation Pause Busy ...............................................................................................4
2.5 Return to Reference Position ......................................................................................................4
2.6 Alarm...........................................................................................................................................4
2.7 M00 .............................................................................................................................................4
2.8 M02/M30 .....................................................................................................................................4
3. Reset Switch and Emergency Stop Button ..................................................................................5
3.1 Reset Switch ...............................................................................................................................5
3.2 Emergency Stop Button ..............................................................................................................5
4. Operation Mode...............................................................................................................................6
4.1 Mode Selection Switch................................................................................................................6
4.2 Jog Feed Mode ...........................................................................................................................6
4.3 Rapid Traverse Feed Mode ........................................................................................................7
4.4 Reference Point Return Mode.....................................................................................................8
4.5 Incremental Feed Mode ............................................................................................................10
4.6 Handle Feed Mode....................................................................................................................10
4.7 Memory Mode ...........................................................................................................................11
4.8 MDI Operation Mode.................................................................................................................12
5. Operation Panel Switches in Operation Mode ...........................................................................13
5.1 Rapid Traverse Override...........................................................................................................13
5.2 Cutting Feed Override...............................................................................................................13
5.3 Manual Feedrate .......................................................................................................................13
5.4 Handle/Incremental Feed Magnification....................................................................................14
5.5 Handle Feed Axis Selection ......................................................................................................14
5.6 Manual Pulse Generator ...........................................................................................................14
5.7 Cycle Start and Feed Hold ........................................................................................................15
5.8 Feed Axis Selection ..................................................................................................................15
6. Operation Panel Switch Functions..............................................................................................16
6.1 Chamfering................................................................................................................................16
6.2 Miscellaneous Function Lock ....................................................................................................16
6.3 Single Block ..............................................................................................................................16
6.4 Dry Run .....................................................................................................................................16
6.5 Manual Override........................................................................................................................16
6.6 Override Cancel ........................................................................................................................17
6.7 Optional Stop ............................................................................................................................17
6.8 Optional Block Skip ...................................................................................................................17
6.9 Manual Absolute .......................................................................................................................18
6.10 Error Detect.............................................................................................................................19
6.11 Follow-up Function..................................................................................................................19
6.12 Axis Removal ..........................................................................................................................19
6.13 Manual/Automatic Synchronous Feed ....................................................................................19
6.14 Handle Interruption..................................................................................................................20
6.14.1 Outline..............................................................................................................................20
6.14.2 Interruptible Conditions ....................................................................................................20
6.14.3 Interruption Effective Axis ................................................................................................20
6.14.4 Axis Movement Speed Resulting From Interruption.........................................................21
6.14.5 Path Resulting After Handle Interruption..........................................................................21
6.14.6 Handle Interruption in Tool Radius Compensation ..........................................................23
6.14.7 Interrupt Amount Reset ....................................................................................................25
6.14.8 Operation Procedure........................................................................................................25
- vii -
6.15 Machine Lock ..........................................................................................................................26
6.16 Deceleration Check.................................................................................................................27
6.16.1 Functions..........................................................................................................................27
6.16.2 Deceleration Check Method.............................................................................................28
6.16.3 Deceleration Check When Opposite Direction Movement Is Reversed ...........................30
6.16.4 Parameters.......................................................................................................................31
6.16.5 Precautions ......................................................................................................................32
7. Stored Stroke Limit .......................................................................................................................34
7.1 Stored Stroke Limit I..................................................................................................................36
7.2 Stored Stroke Limit II.................................................................................................................37
7.3 Stored Stroke Limit IB ...............................................................................................................39
7.4 Stored Stroke Limit IC ...............................................................................................................39
7.5 Movable Range during Inclined Axis Control ............................................................................40
7.6 Stored Stroke Limit for Rotation Axis ........................................................................................41
7.7 Precautions ...............................................................................................................................42
III. MAINTENANCE
1. Daily Maintenance and Periodic Inspection and Maintenance ...................................................1
1.1 Maintenance Items......................................................................................................................1
1.1.1 Escutcheon ..........................................................................................................................1
1.1.2 LCD Panel............................................................................................................................2
1.1.3 Compact Flash/IC card ........................................................................................................2
1.2 Replacement Methods [700 series].............................................................................................3
1.2.1 Durable Parts .......................................................................................................................3
1.2.2 Compact Flash .....................................................................................................................7
1.2.3 IC Card.................................................................................................................................8
1.3 Replacement Methods [70 series]...............................................................................................9
1.3.1 Durable Parts .......................................................................................................................9
1.3.2 Compact Flash ...................................................................................................................11
IV. APPENDIXES
Appendix 1. List of Function Codes..................................................................................................1
Appendix 2. Table of Command Value Ranges................................................................................2
Appendix 3. Circular Cutting Radius Error.......................................................................................8
Appendix 4. Registering/Editing the Fixed Cycle Program.............................................................9
4.1 Fixed Cycle Operation Parameters .............................................................................................9
4.2 Transmitting/Erasing the Fixed Cycle Program...........................................................................9
4.3 Standard Fixed Cycle Subprogram (For L system)...................................................................10
4.4 Standard Fixed Cycle Subprogram (For M system)..................................................................20
Appendix 5. RS-232C I/O Device Parameter Setting Examples ....................................................26
Appendix 6. Alarms ..........................................................................................................................27
6.1 List of Alarms ............................................................................................................................27
6.1.1 Operation Alarms ...............................................................................................................27
6.1.2 Stop Codes ........................................................................................................................35
6.1.3 Servo/Spindle Alarms.........................................................................................................39
6.1.4 MCP Alarm.........................................................................................................................48
6.1.5 System Alarms ...................................................................................................................58
- viii -
6.1.6 Absolute Position Detection System Alarms ......................................................................64
6.1.7 Distance-coded Reference Scale Errors............................................................................67
6.1.8 Messages during Emergency Stop ....................................................................................68
6.1.9 Auxiliary Axis Alarms..........................................................................................................70
6.1.10 Computer Link Errors .......................................................................................................77
6.1.11 User PLC Alarms .............................................................................................................78
6.1.12 Network Service Errors ....................................................................................................80
6.2 Operation Messages .................................................................................................................81
6.2.1 Search-related Operation Messages .................................................................................81
6.2.2 Graphic Display-related Operation Messages ...................................................................82
6.2.3 Variable (Common variables, local variables) - related Operation Messages ...................83
6.2.4 PLC Switch-related Operation Messages ..........................................................................83
6.2.5 Compensation-related (Tool compensation, coordinate system offset)
Operation Messages ..........................................................................................................83
6.2.6 Data Input/Output-related Operation Messages ................................................................84
6.2.7 Parameter-related Operation Messages ............................................................................87
6.2.8 Measurement-related (Workpiece, rotation) Operation Messages ....................................88
6.2.9 Tool (Tool registration, tool life) -related Operation Messages ..........................................89
6.2.10 Editing-related Operation Messages................................................................................91
6.2.11 Diagnosis-related Operation Messages ...........................................................................93
6.2.12 Maintenance-related Operation Messages ......................................................................94
6.2.13 Data Sampling-related Operation Messages ...................................................................96
6.2.14 Absolute Position Detection-related Operation Messages...............................................97
6.2.15 System Setup-related Operation Messages ....................................................................97
6.2.16 Automatic Backup-related Operation Messages..............................................................98
6.2.17 Alarm History-related Operation Messages .....................................................................98
6.2.18 Anshin-net-related Operation Messages..........................................................................99
6.2.19 Messages Related to Machine Tool Builder Network System .......................................104
6.2.20 Other Operation Messages ............................................................................................106
6.3 Program Error .........................................................................................................................107
Appendix 7. G Code Guidance Display List .................................................................................126
- ix -
I. SCREEN OPERATIONS
1. Operating the Setting and Display Unit
1.1 Setting Display Unit Appearance

This explains the functions common to the screens.

An LCD display is used for the screen displays.
Operations such as screen transition and data setting are carried out with the NC keyboard.
The setting display unit is configured of the LCD display, various keys and menu keys as shown below.
The drawing below shows a horizontal layout of the LCD display and NC keyboard, but these can also be
arranged vertically.
<Example for ABC layout keyboard unit> (5) Data setting keys
(alphabet, numerals, symbols)
(3) Previous screen display key
(1) Function keys (11) Frame keys (Part system changeover)
(6) Particular keys

(8) Lower case input key
(16) Operation keys
(7) Data correction keys
(9) SHIFT key
(12) INPUT key
(10) Cursor keys

(14) Menu keys (13) RESET key (2) Page changeover key
(4) Menu changeover keys (15) Menu list key (6) Particular keys
There is the following type of keyboard, too.
(1) Function keys (6) Particular keys
(5) Data setting keys

(alphabet, numerals,
symbols)
(3) Part system changeover key
(6) Particular keys (7) Data correction keys

(15) Menu list key (9) SHIFT key
(13) RESET key (12) INPUT key
(10) Cursor keys

(2) Page changeover key
I-1
The following keys are provided on the keyboard.

Key type Key Operation
(1) Function key MONITOR
(MONITOR) This displays the screen related to "operations".
(Function (Refer to "2. Monitor Screens".)
selection SET UP
(SETUP) This displays the screen related to "setup".
key) (Refer to "3. Setup Screens".)
EDIT
(EDIT) This displays the screen related to "editing".
(Refer to "4. Edit Screens".)
DIAGN
(DIAGN) This displays the screen related to "diagnosis".
(Refer to "5. Diagnosis Screens".)
MAINTE
(MAINTE) This displays the screen related to "maintenance".
(Refer to "6. Maintenance Screens".)
(2) Page PAGE Previous page key When the displayed contents cover several pages, this
changeover displays the contents of the previous page. The " "
key mark at the top of the screen indicates that there is a
previous page.
PAGE Next page key When the displayed contents cover several pages, this
displays the contents of the next page. The " " mark
at the top of the screen indicates that there is a next
page.
(3) Previous BACK (BACK) This redisplays the previously displayed screen.
screen Previous screen display
display key key
(Part system $ $ ($→$) When using a multi-part system NC, this displays the
changeover) Part system changeover data of the next part system. The screen does not
key change if it is a part system common screen or when
only one part system is used.
(4) Menu (left side) This changes the operation menu for the displayed
changeover screen to the current screen group screen selection
key menu. This is also used to cancel the menu operations
of the displayed screen.
(right side) When all of the menus cannot be displayed at once,
this displays the menus not currently displayed. The
" " and " " marks at the bottom of the screen
indicate that there are menus not displayed.
(5) Data setting A B C D E F These keys are pressed to set alphabetic characters,
keys G H I J K L numerals and operation symbols, etc.
M N O P Q R
S T U V W X
Y Z
0 1 2 3 4 5
6 7 8 9 + -
= / . ; etc.
I-2
Key type Key Operation

(6) Particular ? Help key This displays the operation guidance, parameter
keys guidance and alarm guidance corresponding to the
current operation.
?
/ These key definitions differ according to the machine
tool builder.
SFP
F0
(7) Data INSERT (INSERT) This inputs the data insertion mode. When a data
correction Data insert key setting key is pressed, a character is inserted in front
keys of the current cursor position.
The overwrite mode is entered when the DELETE,
C･B CAN, INPUT, cursor or TAB, etc., keys are
pressed, or when the screen is changed.
DELETE (DELETE) This deletes the character just before the cursor
Data delete key position in the data setting area.
C•B This cancels the setting in the data setting area.
CAN / C•B CAN (C･B CAN)
Cancel key
ABC...
(8) Lower case /abc... (LOWER CASE) This changes the input between upper case and lower
input key case alphabetic characters.
(9) SHIFT key SHIFT
(SHIFT) This validates the setting on the lower line of data key.
(10) Cursor keys This moves the cursor up or down one when setting
data in the screen display items.
This moves the cursor one item to the left or right
when selecting data in the screen display items.
at cursor left end: Moves to the right end of
previous line.
at cursor right end: Moves to left end of next line.
This moves the data input cursor one character to the
left or right in the data setting area.
(11) Frame keys This switches the tag.
(12) INPUT key INPUT
(INPUT) This fixes the data in the data setting area, and writes
it to the internal data. The cursor moves to the next
position.
(13) RESET key RESET
(RESET) This resets the NC.
(14) Menu keys This changes the screen and displays the data.
(15) Menu list LIST
(MenuList) This is function that displays each screen's menu
keys configuration as a list. (Refer to "1.7 Menu list")
(16) Operation ALTER (ALTER) This is alternate key (Alt key).
keys This is control key.
CTRL (CTRL)
SP (SP) This is space key.
I-3
1.2 Screen Configuration
(1) (2) (3) (4) (5) (6)
(8)
(9)
(7) (10)
Display items
Display item Details

(1) NC name The currently displayed NC name (name set in parameter "#1135 unt_nm") is
displayed.
(2) Part system name When using the multi-part system, the currently displayed part system name (name
set in parameter "#1169 system name") is displayed.
The part system name is not displayed for the 1-part system.
(3) Power ON request This appears if a parameter requiring the power to be turned ON again has been
changed.
This flickers at an approx. one-second interval.
(4) Operation status The displayed part system's operation mode is displayed.
(5) MDI status The MDI status is displayed when the MDI operation mode is selected.
This does not appear when other operation modes are selected.
(6) Screen name The tab for the currently selected screen is selected and displayed.
(7) Operation status The NC operation status is displayed.
(8) Alarm The currently occurring alarm or warning with the highest priority is displayed.
(9) Operation message The operation message is displayed.
(10) Time The current time is displayed. (Hour: minute)
(11) Anshin-net status This icon appears if Anshin-net diagnosis data has been sent/received.
I-4
1.2.1 Operation Mode
The operation status indicates the operation mode for displayed part system.
The selectable operation mode is following below.
Symbol Details Explanation

MEMORY Memory operation Automatic operation is based on programs stored in the
memory.
TAPE Tape operation Automatic operation is based on tape command (RS232C
input) programs stored in NC tape.
MDI MDI operation Automatic operation is performed with the program set in
the MDI screen.
JOG Jog The jog feed mode enables the axis to be moved by hand
consecutively at the feed rate set by using the MANUAL
FEED RATE switch.
HANDLE Manual handle The handle feed mode enables the axis to be moved by
turning the manual handle. The travel distance per
graduation of the handle depends on how the
HANDLE/INCREMENTAL MAGNIFICATION switch is set.
STEP Step The step feed mode enables the axis to be moved by
hand at feed rate when the FEED AXIS SELECT switch is
ON. The travel distance per graduation of the handle
depends on how the HANDLE/INCREMENTAL
MAGNIFICATION switch is set.
MANUAL Manual arbitrary This mode enables to move manually with arbitrary
feed amount or arbitrary positioning position.
ZERO-RTN Reference point This mode enables a controlled axis to be returned
return manually to the defined position unique to the machine
(reference point).
INIT-SET Automatic This mode enables this mode to manually push against
dog-less the machine end stopper and carry out zero point return.
reference point
return
RAPID Rapid traverse The rapid traverse feed mode enables the machine to be
moved consecutively at rapid traverse feedrate manually.
NO MODE No operation The operation mode is not selected.
mode
(Note 1) Note the following points when using two or more part systems.
The operation mode displays the operation mode selected for the 1st part system. Thus, when
using two-or-more-part-system machine for which the operation modes are separately selected for
each part system, the operation mode displayed for a part system other than the 1st part system,
and the operation mode on the machine may not match.
1.2.2 MDI Status
The MDI status is displayed when the operation mode is the MDI mode.
This does not appear when other operation modes are selected.
The displayed MDI status is following below.
Symbol Details Character color Background color

NON No MDI setting Black Gray
SET MDI setting completed Black Gray
RUN MDI running Black Gray
I-5
1.2.3 Operation Status
1 HLD 2 HLD 3 HLD 4 BST
The operation status displays the currently selected NC operation status for each part system. (The status for
up to four part systems is displayed.)
Symbol Details Character color Background color

EMG In emergency stop Red Dark gray
RST Resetting NC White Dark gray
LSK Paper tape reader is in label skip state White Dark gray
BST In block stop White Dark gray
HLD Operation halted White Dark gray
SYN Synchronizing White Dark gray
AUT In automatic operation White Dark gray
RDY Operation completed state Green Dark gray
1.2.4 Alarms/Warnings
When an alarm or warning occurs, the alarm No. and alarm message character string are displayed.
(Example) Warning display

S51 Parameter error
Character color Background color

Alarm White Red
Warning Black Yellow
1.2.5 Operation Messages
Character color Background color

Operation messages Black Green
The operation message can be reset by pressing any key.

The following operation messages are released even if automatic start or reset is executed.
• "Search completed"
• "Restart search is completed"
• "Top search completed"
• "MDI Set ended"
(Example)
Searching
I-6
1.3 Screen Transition Diagram

The screen is configured of operation groups.
Refer to "1.4 Screen Selection Procedures" for how to display the screens.
Search Research Edit Trace Check Cnt exp Offset Coord Cnt set MST
Monitr
Modal Tree Time Com var Loc var P corr PLC SW G92 set Col stp LD MTR
Sp-stby TipDisp All sp

Refer to "2. Monitor Screens"
T-ofs T-meas T-reg T-life Coord W-meas User MDI Cnt set MST
T-list Pallet
Setup
Process Fixed Control Operate I/O Ethernet Link Subpro Axis Barrier
param cycle param param param param param stor param data
Hi-prec Hi-prec
param axis
Refer to "3. Setup Screens"
Edit Check I/O

Edit
Refer to "4. Edit Screens"
H/W S/W Option I/F dia Drv mon Mem dia Alarm Selfdia NC smp Anshin MTB
Config display message net net
Diagn
Servo Spindle Power AUX Synchro

unit unit unit unit error
Refer to "5. Diagnosis Screens"
Mainte Param Input/

Output
Mainte
Process Control Axis Operate Barrier I/O Ethernet Link Subpro BaseSys
param param param param data param param param stor param
BaseAx BaseCom Axis Zp-rtn Abs pos Servo Spindle Spindle RotAxis
spec param spec param param param spec param param
PLC PLC inc PLC PLC Bit Er Comp Er Comp Macro Posn AUX
timer timer counter constnt select param data list switch param
Open Open CC-Link CC-Link

Refer to "6. Maintenance Screens"
param 1 param 2 param 1 param 2
I-7
1.4 Screen Selection Procedure
The screen is selected by pressing a function key such as MONITOR or SETUP, or by pressing a menu key
displayed in the screen selection menu.
Operation method (To display "T-ofs" screen from the "Setup screen")
(1) Press the function key SETUP. The previously displayed setup screen will appear.
The menu display will differ according to the L

system/M system and parameter setting.
(2) Press the menu T-ofs key. Tool compensation amount screen appears.
I-8
1.5 Setting Data
1.5 Setting Data
1.5.1 Setting Numerals and Alphabetic Characters
Operation method
The data is basically set with the following methods:

(1) Menu selection
(2) No. selection
(3) Cursor movement
(4) Data key input
(5) INPUT key input
(Note 1) The contents in the data setting area are only displayed until the INPUT key is pressed.
These contents are invalidated if the screen is changed. The data is written into the memory when
the INPUT key is pressed.
(Note 2) Special settings may be required depending on the data type. Refer to each item.
(Note 3) The cursor may move to the right of the display item depending on the data type.
(Note 4) If an illegal key is set, an error occurs when INPUT is pressed. Reset the correct data.
Operations in the data setting area
The key is input at the position where the cursor is displayed. If a cursor is not displayed, the key input is
invalid.
When a key is input, the data appears at the cursor position, and the cursor moves one character space to
the right.
/ keys: Moves the cursor one character to the left or right.
(1) The cursor is at the position shown on the 123777456

right.
(2) Press the key. The cursor moves one character space to the right.
123777456
INSERT key: Enters the insert mode.
(1) Move the cursor to the position where the The cursor moves in the data setting area.
data is to be inserted. 123456
(2) Press the INSERT key, and then the data The cursor moves one character space to the right.
keys. 123777456
INSERT 7 7 7
(Note) The overwrite mode is entered when the DELETE, C·B CAN keys are pressed, or when the screen is
changed.
I-9
1.5 Setting Data
DELETE key: Deletes the character in front of the cursor.
(1) Move the cursor to the position where the The cursor moves in the data setting area.
data is to be deleted. 123777456
(2) Press the DELETE key. The character in front of the cursor is deleted, and the
cursor moves.
12377456
C·B key: Deletes all characters in the data setting area.
(1) Press the C·B key. The cursor moves in the data setting area.
Cursor operations on the screen
If a cursor is displayed on the screen, data is set in the data setting area and the INPUT key is pressed, the
data appears at the cursor position on the screen. The cursor moves to the next position.
The following keys can be used to move the cursor with the cursor keys.
: Moves the cursor to the previous line.

: Moves the cursor to the next line.
: Moves the cursor one item to the left.
: Moves the cursor one item to the right.
I - 10
1.5 Setting Data
1.5.2 Inputting Operations
In addition to the method of directly inputting numeric data for specific data settings, a method to input the
operation results using four rules operators and function symbols can be used.
Input method
Numeric values, function symbols, operators and parentheses ( ) are combined and set in the data setting
area.
The operation results appear when the INPUT key is pressed. Data for the currently selected setting item will
be set when INPUT key is pressed again. The contents in the data setting area are erased.
Examples of operator settings, Function symbols, setting examples

and results and results
Setting Operation Function Setting Operation
Operation Function
example results symbol example results
Absolute
Addition =100+50 150 ABS =ABS (50-60) 10
value
Subtraction =100-50 50 Square root SQRT =SQRT (3) 1.7320508
Multiplication =12.3∗4 49.2 Sine SIN =SIN (30) 0.5
Division =100/3 33.3333333 Cosine COS =COS (15) 0.9659258
=1.2∗ Tangent TAN =TAN (45) 1
Function 5.4
(2.5+SQRT(4)) Arc tangent ATAN =ATAN (1.3) 52.431408
Operation examples
(1) Set as shown below, and press the The operation results appear in the data
INPUT key. setting area.
=12∗20 INPUT 240 |
(2) Press the INPUT key again. Data for the selected setting item is set.
The result is displayed on the screen.
The cursor moves to the next position.
Notes for using operators and functions
Division : Zero division causes an error.

Square root : If the value in the parentheses is negative, an error occurs.
Triangle function : The unit of angle θ is degree (°).
Atangent : -90 < operation results < 90.
I - 11
1.5 Setting Data
Restrictions
(1) Always use "=" for the first character.

(2) Do not use the following characters as the second character or last character.
Invalid as second character: ∗, /, )
Invalid as last character: ∗, /, (, +, -
(3) Make sure that the left parentheses and right parentheses are balanced.
(4) The 360° limit does not apply on the angle. SIN (500) is interpreted as SIN (140).
(5) While the Monitor screen or the Setup screen displaying, if the axis name address, M, S, T, 2nd
miscellaneous function code (B, etc.) is pressed when "=" is set in data setting area as the first character,
the operation input is given to priority. So, the window does not open, and the cursor does not move.
(6) The exponential setting, like "1.23E-4", cannot be used. The operation result is not displayed with
exponential.
(7) It is not possible to set characters exceeding the number of characters which can be input to the data
setting area.
(8) It is not possible to omit "0" before the decimal point, like ".5", when operation inputting. An error will
occur.
(9) The accuracy is guaranteed for the calculation with 15 digits or less. The calculation with over 15 digits
does not guarantee its accuracy.
(10) The operator or the function which does not exist in the above-mentioned, such as "ASIN", cannot be
used. The operation message "Setting error" appears, and the display of the data setting area does not
change.
(11) Regardless of the input setting unit and metric system/inch system, the digit numbers below the decimal
point of the operation result is seven digits or less.
I - 12
1.6 Operating the Screen
1.6 Operating the Screen
1.6.1 Changing the Displayed Part System
When the $ $ key is pressed, the displayed part system changes.

The displayed part system No. is counted up by one each time the $ $ key is pressed. If the displayed part
system No. exceeds the value number of part systems, the displayed part system No. returns to 1.
1.6.2 Changing the Menu
The menu can be used to select screens and to select functions or setting items. Up to ten menus can be
displayed at once.
To select the menu, use the menu key below the menu display.
To change the menu, use the menu changeover key.
key : The operation menu is canceled.

The screen selection menu for the currently displayed screen group appears.
The display for the currently displayed menu is highlighted.
key : When there are more than 11 menus, this key displays the remaining menus.
This key can be used when " " or " " is displayed at the upper right of the menu.
1.6.3 Types of Menus

The menus are categorized into the following types according to the operation that takes place after the menu
key is pressed.
A : The menu is highlighted, and the system waits for the user input. After the input, the operation follows
the input details.
B : The menu is highlighted, and operation starts.
C : Operation starts without highlighting the menu.
In section "2. Monitor screen" and following, the types are described in the following method.
(Example) Explanation of menus used for editing the program on the Edit screen (excerpt)
Menu Details Type Reference

String When the character string is designated and the INPUT key is A 4.2.11 Searching for
search pressed, that character string is searched for. character strings
If the character string to be searched for and the character string to A 4.2.12 Replacing
String be replaced are separated with a "/" and designated, when the character strings
replace
INPUT key is pressed, the replace operation takes place.
Operation when menu is pressed Menu type Reference section
I - 13
1.7 Menu List
1.7 Menu List

The menu list is a function that displays each screen's menu configuration as a list. The Menu list window
opens when the MenuList key is pressed on each screen.
If a pop-up window other than the menu list is displayed, the Menu list window appears above the displayed
pop-up window. The menu does not change in this case.
If the MenuList key is pressed again or if the Cancel key is pressed while the Menu list window is open,
the Menu list window closes, and the state before the MenuList key was pressed is recovered.
(1)
(2)
(3)
Display items

(1) Screen name The screen name is displayed.
(Example) Monitr/Setup
(2) Menu name A list of the menu names (functions) included on each screen is displayed.
(Example) Search/Reserch
(3) Function outline display An outline of the currently selected menu name (function) is displayed.
area
I - 14
1.7 Menu List
List of menu names (functions)
Screen Menu name Outline

Monitr Search Call a program for automatic operation.
Reserch Restart machining from a selected block.
Edit Edit the machining program searched for operation.
Trace Trace the T path based on the machining program being executed.
Check Trace the T path based on the machining program w/o running machine.
Cnt exp Display counters of all axes & select the type of the counters.
Offset Set & display tool offset data.
Coord Set & display workpiece coordinate system offset.
Cnt set Set the relative position counter to an arbitrary value.
MST Set & display each command for S, M, T & 2nd M functions.
Modal Display the execution modal value of the machining program.
Tree Display program/MDI interrupt/user macro call in nesting structure.
Time Set & display integrating time (date, time, power ON time, etc.).
Com var Set & display the details of common variables.
Loc var Specify a nesting level of subprogram & display local variables.
P corr Correct & change the next command by block stop during auto-/MDI op.
PLC SW Switch ON/OFF each NC ops. control signal allocated by ladder program.
G92 set Perform origin set & origin cancel.
Col stp Register arbitrary collation & stop position set as single block stop.
LD MTR Spindle load and Z axis load, etc. can be displayed in meter.
Sp-stby The spindle tool No. and the standby tool No. can be displayed.
TipDisp Display tool tip pos, handle interrupt amount and tool tip speed.
All sp Display commanded/actual rot speed values of all the spindles.
Setup T-ofs Set & display tool offset data.
T-meas Measure T length & radius manually & set them as tool offset amounts.
T-reg Register T No. according to the magazine pot, spindle & wait position.
T-life Scale workpiece to figure face/hole ctr/wid ctr & set as coord ofs.
Coord Set & display workpiece coordinate system offset.
W-meas Set & display user parameters.
User Display & edit MDI programs set in NC memory.
MDI Edit (add/delete/change) programs in NC memory & create new ones.
Cnt set Set the relative position counter to an arbitrary value.
MST Set & display each command for S, M, T & 2nd M functions.
T-list Reference & display T-codelist.
Pallet The machining program is registered into the pallet of APC.
Edit Edit Edit (add/delete/change) programs in NC memory & create new ones.
Check Trace the T path based on the machining program w/o running machine.
NAVI Create the part program simply.
I/O Input/Output machining programs betw. NC memory & external I/O device.
I - 15
1.7 Menu List
Screen Menu name Outline

Diagn Config Display the H/W & S/W (S/W No. & version) configurations.
Option Display the details of the options registered in NC memory.
I/F dia Set & display input/output signals of the ladder program.
Drv mon Display drive diagnostic information. (servo/spindle/power supply).
Mem dia Set & display NC internal data.
Alarm Display a list of currently occurring alarms & their messages.
Selfdia Display the H/W & Operation stop state.
NC Smp Set Sampling parameter & Sample NC internal data.
A net Customer service is available by connecting NC with NC service.
MTB net Machine maker service is available by connecting NC & machine maker.
Mainte Mainte Perform NC memory format/abs. para. setting/maint. data backup, etc.
Param Select a type of parameter to set & display the parameter values.
I/O Input/Output machining programs betw. NC memory & external I/O device.
I - 16
1.7 Menu List
1.7.1 Displaying the Menu Function Outline
Operation method
(1) Press the MenuList key. The Menu list window appears showing the selected
screen's menu list at the top.
When the MenuList key is pressed while
editing the file on the Edit screen, a prompt
to confirm whether to save the program
appears before Menu list window opens.
(2) Using the ↑ , ↓ , → , ← and page keys, move The function outline for the selected menu appears.
the cursor to the menu for which the function The function outline does not appear if a menu with no
outline is to be displayed. name is selected.
The cursor does not move to the group
name.
1.7.2 Directly Moving to the Menu Function
Operation method
(2) Using the ↑ , ↓ , → , ← and page keys, move The function outline for the selected menu appears.
the cursor to the menu to move to.
(3) Press the INPUT key. The selected menu function can be moved to directly.
The menu is not moved to if a menu with no name is
selected.
The Menu list window closes after moving.
I - 17
1.7 Menu List
1.7.3 Moving the cursor
Operation method
(2) Press the ↓ key four times. The cursor moves down four times, and the screen
scrolls.
(3) Press the ↑ key three times. The cursor moves up three times, and the screen scrolls.
(4) Press the PageDown key once. The screen scrolls.
I - 18
1.7 Menu List
(5) Press the ← key once. (Note 1) The cursor moves to the upper right, and the screen
scrolls.
(6) Press the PageUp key once. The screen scrolls.
(7) Press the ↓ key twice. The cursor moves down twice.
(Note 1) The cursor moves in the same way even when the |← key is pressed.
(Note 2) The cursor moves in the same way even when the →| key is pressed.
I - 19
1.8 Guidance Function
1.8.1 Parameter Guidance
The parameter/operation guidance function displays the details of the parameters or the operation methods
according to the state of the screen currently being displayed.
Screen configuration
The parameter/operation guidance window is displayed with the following type of configuration.
The parameter
detail or operation
method is
displayed.
Operation method
If the ? key is pressed on any screen, the guidance window will open. If a pop-up window other than the
guidance window is open, the guidance window will open over the currently opened pop-up window. In this
case, the menu state does not change. If ? key or CANCEL key is pressed again when the guidance window
is open, the guidance window will close and the screen will return to the previous state in which the ? key was
pressed.
I - 20
Displaying the operation guidance
(1) Press the Edit menu on operation screen. The edit window is displayed.
(2) Press the ? key. The guidance window is opened, and sub-contents for
edit operation method is displayed.
(Note) If the explanation of operation method is

nothing, the contents list is displayed.
(3) Move the cursor to the operation method Select the "Program editing - Undoing program
to be displayed by , ,PAGE, PAGE
changes" with the cursor.
keys.
(4) Press the INPUT key. The operation method for "Program editing - Undoing
program changes" is displayed.
(Note 1) If the parameter tag such as machine parameter, fixed cycle, etc. is opened with the key, the
details for the top parameter are displayed.
I - 21
Displaying the parameter guidance
(1) Press the Param menu on maintenance The machining parameter screen is displayed.
screen.
(2) Press the key, and move the cursor

to "#8005 ZONE r" parameter.
(3) Press the ? key. The guidance window is opened, and the detail of
"#8005 ZONE r" parameter is displayed.
(4) Press the key. The operation method for parameter screen is
displayed.
(Note 1) While guidance window is displayed, the parameter details displayed on each parameter type tab
are recorded. Therefore, when the parameter type is switched with / key, last displayed
parameter details are displayed.
(Note 2) If the parameter No. cannot be gotten (the cursor is non-display, the cursor is put on blank line, the
cursor is put on comment line), the top of parameter guidance for each parameter appears.
I - 22
Displaying the operation guidance by selecting the contents
(1) Press the Search menu on operation The operation search window is displayed.
screen.
(2) Press the ? key. The parameter/operation guidance window is opened,

and sub-contents for operation search is displayed.
(3) Press the key. The contents for operation guidance are displayed.
(4) Move the cursor to the operation method Select the "Restart search - Restart type 2" with the
to be displayed by , ,PAGE, PAGE
cursor.
keys.
I - 23
(5) Press the INPUT key. The operation method for "Restart search" is
displayed.
(Note 1) The operation details of function that cannot be selected because of no option are also displayed on
the contents list.
(Note 2) When the key is pressed during the contents display, the sub-contents for operation search
(operation method (2)) are displayed.
Precaution
(1) If the ? key is pressed when alarm occurs, the alarm guidance window will open.
(2) To display another operation method, select newly an operation method from the contents list. It is not
possible to jump from the parameter, operation details to other details.
(3) When the ? key is pressed while the menu list window is displayed, the guidance window is opened after
the menu list window is closed.
I - 24
1.8.2 Alarm Guidance
The alarm guidance is the function that displays message, details and remedy for the currently occurring
alarms.
This function is an option.
Screen configuration
The alarm guidance is displayed in "alarm" tag on "operation/parameter/alarm guidance window".

The "alarm" tag is on the rightmost end of the guidance window.
A scroll bar appears when details and remedy, etc. do not fit in one page.
(1)
(2)
(3)
Display items

(1) Message This displays "NC alarm" and "PLC alarm message". The displayed content is same
as the content displayed in the alarm message of the diagnosis screen.
(2) Number of page This displays "order of priority / total number of occurring alarms".
(3) Details/Remedy, etc. This displays detail and remedy, etc. for alarm message.
I - 25
Operation method
If the ? key is pressed on any screen, the alarm guidance window will open. If a pop-up window other than
the alarm guidance window is open, the alarm guidance window will open over the currently opened pop-up
window. In this case, the menu state does not change. If ? key or CANCEL key is pressed again when the
guidance window is open, the guidance window will close and the screen will return to the previous state in
which the ? key was pressed.
Displaying the alarm guidance
(1) Press the ? key during occurring alarm on The guidance window is opened while "alarm" tag is
operation screen. valid. The alarm details and remedy are displayed for
(Ex.) When "H/W stroke end axis exists" "H/W stroke end axis exists".
and another alarm occur.
(Note 1) The alarm guidance is executed for the alarm that is occurred when the ? key has been pressed.
Therefore, the guidance will be displayed continually even if the alarm is reset while the alarm
guidance is displayed. The alarm guidance is not executed for the alarm that has occurred while the
alarm guidance is displayed.
(Note 2) If the ? key is pressed when an alarm is not occurring, the operation/parameter guidance appears.
In this state, if the "alarm" tag is selected with the right frame key, nothing is displayed in the
message, details and remedy columns. (These columns are blank.)
(Note 3) All the explanations of the alarm having the same error class and No. are displayed in the details
column.
I - 26
Changing the alarm guidance
(1) Press the key or key when the The alarm guidance with one priority lower than the
alarm guidance is displayed. current alarm guidance is displayed.
If the key or key is pressed when the lowest
priority alarm is displayed, the alarm with the highest
priority is displayed.
(Ex.) When 3 alarms occur.
(1/3) (2/3) (3/3)
(2) Press the key or key when the The alarm guidance with one priority higher than the
alarm guidance is displayed. current alarm guidance is displayed.
If the key or key is pressed when the
highest priority alarm is displayed, the alarm with the
lowest priority is displayed.
(Ex.) When 3 alarms occur.
(1/3) (2/3) (3/3)
(Note 1) Up to 10 alarm guidance displays are displayed in order of priority.

(Note 2) Even if the , , or key is pressed when only one alarm occurs, the screen display is
not switched.
Precautions
(1) While the user parameter window on "Setup" or the parameter screen on "Mainte" is displayed, the
parameter guidance display will be prioritized even if an alarm occurs.
(2) When the ? key is pressed while the menu list window is displayed, the guidance window is opened after
the menu list window is closed.
(3) The alarm guidance of stop code and operator message is not displayed.
I - 27
1.9 Touch Panel Functions [700 series only]
Touch panel screen operation is available with a touch panel display unit.
1.9.1 Basic Operation
(1) (2)
(3)
(4)
(5)
(6)
Display items

(1) System This switches from the current part system to the next current system.
(2) Main tag A selected screen will open.
As in the case with a screen change by key inputting, if a popup window is displayed,
close it before changing screens. If there is a file under editing, save the file before
changing screens.
(3) Sub tag This displays the contents of the selected tag.
When a tag is changed while operation menu is on a wait to be input, the input wait
status is cancelled and then the tag is changed.
Sub tags are available on Setup screen, Edit screen, parameter/operation guidance
window.
(4) Scroll bar If [ ][ ] of a scroll bar is touched, the view is scrolled one line up/down.
If any part of scroll bar besides tabs is touched, the page jumps to the next/previous
one.
(Note) In some screens, if [ ][ ] is touched, the page jumps to the next/previous
one, and scrolling by line is not possible.
(5) Next menu This switches to the next menu if available.
(6) Menu When a menu is selected by touching, the menu's process is executed.
I - 28
Moving cursor by touch panel
When a place within the data setting area of the screen having a cursor is touched, the cursor moves to the
touched position. Cursor movement by touch panel operation is also possible in the area where the cursor is
moved by , , , , keys. When a window is closed after cursor movement, the cursor
position is returned to the first line. When the cursor is moved or the area is changed by touch panel
operation in the Y/N input wait status (when the [Line clear] menu is selected, etc.) the status will be that
when N is selected (canceled), and then the cursor movement or area change will be carried out.
(Example) Cursor movement while waiting for Y/N input

(1) Select the Coord menu on the monitor Workpiece coordinate system offset window is
screen. displayed.
(2) Select the ALL clear menu. The ALL clear menu is highlighted.
The message "Clear all?(Y/N)" is displayed.
(3) Touch the coordinate value for the The cursor is moved to the touched position.
arbitrary coordinate system offset. The highlight of the ALL clear menu is undone and
"All clear" is canceled.
The message "Clear all?(Y/N)" disappears.
Changing active area
In the screen where active area can be changed, the area touched will become active.
Active area cannot be changed by touch panel operation during mass-editing or file saving for automatic
backup.
I - 29
1.9.2 Menu List
(1) (2)
Display items

(1) Menu selection The menu touched is turned active. Its screen will be displayed by touching that
active menu once again or by pressing the INPUT key.
one.
I - 30
1.9.3 Operation/Parameter Guidance
(1)
(3)
(2)
(4)
(5)
Display items

(1) Guidance tag Type of guidance is changed.
(2) Cursor When either "Content" tag or "Operate" tag is selected, if an item is touched, the
cursor moves to that item. The contents will be displayed by touching the item at the
cursor position once again or by pressing the INPUT key.
one.
(4) Tag change Active tab shifts one toward right/left.
(5) Page change By touching mark, previous page is displayed; by touching mark, next
page is displayed.
I - 31
1.10 Touch Panel S/W Key
When a touch panel display unit is used, touch panel operation is available.
With the touch panel soft key function, a key input is possible by touching a key on the S/W keyboard which is
displayed on the screen. S/W keyboard is displayed if S/W Key button is touched in each screen. In this
case, screen or menu status will not change. S/W keyboard is always displayed on the front screen. When
the CLOSE key on the S/W keyboard is touched, the S/W keyboard will be closed. S/W keyboard will be
enabled when the parameter "#11010 Software keyboard" is set to "1". When S/W keyboard is disabled,
S/W Key button is not displayed.
I - 32
(10)
(11)
(1)
(12)
(2)
(3) (3)
(4) (13)
(5)
(6) (7) (8) (16) (15) (14)

(9)
Display items

(1) Input area This displays a character string according to the keys touched by the operator.
(2) Lower-case letter input This changes upper/lower-case of alphabet. The ABC../abc.. key is highlighted
key when the lower-case-letter-setting is valid.
(3) Data setting key This enters characters in the input area or screen.
(4) Window operation key LIST : This displays the menu list window.
? : This displays the parameter/operation guidance window.
: This displays the window.
: This changes active windows.
(5) Reset key This resets the NC.

(6) SFP key This displays the onboard screen or custom screen.
(7) F0 key This displays the onboard screen.
(8) Page change key This displays the contents in the previous/next page.
(9) Cursor key If data is set in the display items on the screen, the cursor is moved to up, down, left
and right.
(10) Blank key This enters a blank.
(11) Data correction key INSERT :The mode changes to data insertion mode, and characters are
input at the current cursor position when data setting key is
pressed.
When DELETE, C.B CAN, INPUT, cursor key, or tab key, etc. is
pressed, or when the screen is changed to another, the mode
returns to overwriting mode.
DELETE : This deletes a letter before the cursor position.
C.B : This cancels the settings in the input area.
CAN : This cancels.
I - 33

(12) Display position switch This switches the display position of the S/W keyboard.
(13) Block end key This enters ";".
(14) INPUT key This confirms the data entered in the input area or screen.
(15) Shift key This validates the setting on the lower line of data setting key.
Once SHIFT key is selected, it will be valid until another key is pressed or
the S/W keyboard is closed. Menus are displayed in highlight while SHIFT
key is valid.
(16) CLOSE key This closes the S/W keyboard.
1.10.1 Operation Method
Displaying/closing the S/W keyboard
(1) Touch the S/W Key button. S/W keyboard is displayed on the front screen.
S/W Key button is highlighted.
(2) Touch the CLOSE key, or touch the S/W keyboard will close.
S/W Key button again.
Changing the display position
(1) Touch the S/W Key button. S/W keyboard is displayed on the front screen.
S/W Key button is highlighted.
(2) Touch located at the upper right S/W keyboard is displayed on the upper side of the
screen.
corner of the S/W keyboard.
changes to .
(3) Touch located at the upper right S/W keyboard is displayed on the upper side of the
screen.
corner of the S/W keyboard.
changes to .
I - 34
Entering data when the input area is enabled
If displaying the S/W keyboard while input area is being displayed on a screen, such as in the case where the
operation search window or setup screen is being displayed, the S/W keyboard input area will be valid. At this
time, the key selected on the S/W keyboard is temporarily displayed in the S/W keyboard input area, and then
is input and set in the screen by selecting the INPUT key.
(Example) Set the value in T tool compensation amount

(1) Display T compensation tag on the setup S/W keyboard is displayed.
screen and touch the S/W Key button. S/W keyboard input area will be invalid.
(2) Touch the , , keys to The cursor for tool compensation amount is moved.
move the cursor to an arbitrary position.
(3) Touch the data setting key and enter the "15" is displayed in the S/W keyboard input area.
value.
Example: 15
(4) Touch the INPUT key. "15" is input at the tool compensation amount cursor
position.
Entering data when the input area is disabled
If S/W keyboard is displayed while edit window is displayed for program editing or input area is not displayed
on a screen, or when the monitor screen main menu is displayed, S/W keyboard input area will be invalid. At
this time, the key selected on the S/W keyboard is directly input to the screen.
(1) Display the edit window on the monitor S/W keyboard is displayed.
screen and touch the S/W Key button. S/W keyboard input area will be invalid.
(2) Touch the , , keys to The cursor for the edit window is moved.
move the cursor to an arbitrary position.
(3) Touch the data setting key and enter the "G28" is displayed in the edit window.
value.
Example: G28
(4) Touch the INPUT key. "G28" which has been input in the edit window is
confirmed.
I - 35
1.11 Screen Saver (Backlight OFF) Function
The screen saver function protects the display unit by backlight OFF after the time set in the parameters has
elapsed.
The backlight can also be turned OFF with key operations on the Monitor screen.
The backlight is turned ON by pressing any key, or by touching anywhere on the screen when the display unit
carries a touch-sensitive screen.
1.11.1 Backlight OFF
The screen saver function has two types: "Automatic change function" that the backlight is turned OFF after a
certain period of time, and "Manual change function" that the backlight is turned OFF by key operations.
Automatic change function
If there is no key input, no operation from touch-sensitive screen, or no screen display request signal input
from the machine within the time set in the parameter "#8078 Screen Saver Time", the backlight will be turned
OFF.
If "#8078 Screen Saver Time" is set to "0", the backlight will not be turned OFF.
Manual change function
The backlight can be turned OFF by pressing the SHIFT and C.B CAN keys on the Monitor screen (when a
pop-up screen is not displayed). It is possible to be turned OFF by inputting the keys from the S/W keyboard.
Even if "#8078 Screen Saver Time" is set to "0", the backlight can be turned OFF by pressing the SHIFT and
C.B CAN keys.
(Note 1) Even if the SHIFT and C.B CAN keys are pressed when a screen other than the main menu is
displayed on the Monitor screen (when a pop-up window is displayed), the backlight cannot be
turned OFF.
(Note 2) The backlight cannot be turned OFF by the manual change function on screen other than Monitor
screen.
I - 36
1.11.2 Backlight ON
If a key is pressed or the screen display request signal is input while the backlight is OFF, the backlight will be
turned ON.
The backlight is turned ON by touching anywhere on the screen if the display unit carries a touch-sensitive
screen. In that case, even if the screen name tab or the menu is touched, the display is not changed.
Key operation
The correspondence when the key is pressed is as follows during backlight OFF.
(1) Backlight ON + screen transition
(Example) Function key, Part system changeover key, Frame keys, ? key, etc.
(2) Backlight ON only

(Example) Page changeover key, Menu changeover key, Data setting keys, Data correction keys, etc.
(3) The key input is ignored

(Example) RESET key, SHIFT key, ALTER key, CTRL key
Precautions
(1) The backlight will not be turned ON even if the reset key is pressed. However, if the screen display
request signal is input when the reset key is pressed, the backlight will be turned ON. Refer to the
instruction manual issued by each machine tool builder for details. Note that whether the backlight will be
turned ON when any of the machine operation board keys (other than the NC operation board keys) is
pressed will differ according to the machine specifications. Refer to the instruction manual issued by
each machine tool builder for details.
(2) If a key is pressed or the screen display request signal is input while the screen is displayed, counting of
the time to turn the backlight OFF will restart. However, even if SHIFT, ALTER or CTRL key is pressed,
counting of the time to turn the backlight OFF will not restart.
(3) Operation when the or key is pressed will differ according to the machine tool builder. Refer to
the instruction manual issued by each machine tool builder for details.
(4) When the backlight is turned ON, the first character is ignored if the SHIFT + A to W key is input. (Ex.
WHILE -> HILE)
(5) The S/W keyboard is operated regardless of backlight ON/OFF. However, when the backlight is OFF, the
key input is ignored even if the following keys are input from S/W keyboard.
• Data setting keys
• Data correction keys
• SP key
• INPUT key
• Cursor keys
• Page changeover key
I - 37
2. Monitor Screens
2. Monitor Screens
Various information related to operation, such as the axis counter, speed display and MSTB command are
displayed on the Monitor screen. The following operations regarding operation can be executed.
(1) Operation search
(2) Restart search
(3) Editing the searched machining program
(4) Trace (Display of machine movement path)
(5) Check (Display of NC program's tool movement path)
(6) Correction of operating program's buffer
(7) Counter set
(8) Manual numeric command etc.

"Auto/MDI" and "Manual" are displayed at the upper left of the screen. These displays change according to
the mode selection switch. The details displayed for [Auto/MDI] differ according to the number of NC axes.
[For Auto/MDI (Part system with five or less axes)]
(6)
(7)
(8)
(1)
(9)
(10)
(11)
(2)
(12)
(3)
(4)
(5)
I - 38
2. Monitor Screens
[For Auto/MDI (Part system with six or more axes)]
[For Manual]
(6)
(7)
(8)
(1) (9)
(10)
(11)
(12)
(5)
I - 39
2. Monitor Screens
Display items

(1) Counter display This displays the counter of the relative position and workpiece coordinates
positions, etc.
If each axis is in a specific position or status, the following status symbol appears.
#1 to #4 : No. 1 to No. 4 reference position
][ : Servo OFF state
MR : Mirror image
>< : Axis removed state
Whether to allow for the tool length compensation and tool radius compensation can
be set with the parameter "#1287 ext23/bit4".
(2) G modal simple display This displays the modal status.
G command modal status of Group 1
G command modal status of Group 3
Selected workpiece coordinate system
Tool radius compensation modal, compensation No. shape compensation amount,
tool radius wear amount
Tool length compensation modal, compensation axis name, compensation No.,
shape compensation amount, tool length wear amount
(3) Cycle time display This displays the automatic operation time and cycle time.
The displayed items are switched with integrated time window.
(4) Completed workpiece This displays the number of workpieces which have been completed.
display The display follows the machining parameters "#8001 WRK COUNT M" to "#8003
WRK COUNT LIMIT".
(5) Machine status animated This displays the current tool No., tool type, next command movement direction,
display coordinate rotation status, mirror image status, and spindle rotation direction/coolant
status.
Note that the spindle rotation direction/coolant status display differ according to the
machine tool builder.
(6) M, T, B commands This displays the values command for M (miscellaneous function command value), T
(tool command value) and B (2nd miscellaneous function command value).
The displayed number of M (miscellaneous function command value) depends on
parameter "#12005 Mfig".
The displayed number of T (tool command value) and B (2nd miscellaneous function
command value) is "1" regardless of the parameters "#12009 Tfig" and "#12011
Bfig". However, the display/non-display of B (2nd miscellaneous function command
value) depends on parameter "#1170 M2name".
Refer to "Manual numerical value command" for the manual numerical value
commands.
(7) Speed display In interpolation feed:
This displays the vector direction speed currently being moved in.
In each axis independent feed:
This displays the speed of the axis with highest speed.
The actual machine feedrate is displayed with the parameters "#1125 real_f".
(8) S command, This displays the S (spindle command rotation speed) and spindle actual rotation
spindle actual rotation speed value.
speed display If there are two or less spindles, the S command value and the spindle actual
rotation speed are displayed.
If there are three or more spindles, only the S command value is displayed.
(9) Spindle/Wait display The spindle tool No. and the standby tool No. are displayed.
These displayed contents differ according to the machine tool builder.
(10) Load meter display The spindle load and Z axis load, etc., are displayed in a bar graph.
If Spindle/standby display is not being used, a load meter can be displayed in the
Spindle/standby display area. These displayed contents differ according to the
I - 40
2. Monitor Screens

(11) Machining program
currently being executed
(Note)
Main 010… This displays the program No., sequence No. and block No. currently being
executed.
Sub 01234… When a subprogram is being executed, this displays the subprogram's program No.,
sequence No. and block No.
(12) Buffer display This displays the contents of the machining program currently being executed.
The block being executed is highlighted.
(Note) If the program No. (program name) exceeds 12 characters, "*" will appear at the 12th character.
I - 41
2. Monitor Screens
Menus
Menu Details Reference

This executes operation search. 2.2 Operation Search
This executes restart search. 2.3 Restart Search
This edits the machining program in search. 2.4 Program Edit
This executes trace. 2.5 Trace
This checks the program. 2.6 Program Check (2D)

This menu does not appear if the program check function option is not 2.7 Program Check (3D)
provided.
This enlarges the counter, and displays the counters for all axes. 2.8 Counter All-axis
Display
This displays the tool compensation amount. 2.9 Tool Offset Amount
A value can also be set for the tool compensation amount.
This displays the workpiece coordinate system offset. 2.10 Workpiece

A value can also be set for the workpiece coordinate system offset. Coordinate System
Offset
A arbitrary value can be set in the relative position counter. 2.11 Counter Set
This executes a manual numerical value command. 2.13 Manual Numerical

Value Command
I - 42
2. Monitor Screens

This displays the program modal. 2.14 Modal Display
This displays the program tree. 2.15 Program Tree

Display
This displays the date, time and integrated time, etc., The date, time 2.16 Integrated Time
and integrated time, etc., can also be set. Display
This displays the common variables. 2.17 Common Variables

A value can also be set for the common variable.
This displays the local variables. 2.18 Local Variables
This corrects the buffer. 2.19 Buffer Correction
This turns the PLC switches ON or OFF. 2.20 PLC Switch

Function
This sets and cancels the origin. 2.12 Origin Set, Origin
Cancel
This executes verify stop. 2.21 Verify Stop
The spindle load and Z axis load, etc., are displayed in a bar graph. 2.22 Load Meter Display
These displayed contents differ according to the machine tool builder.
The current spindle tool No. and the standby tool No. are displayed. 2.23 Spindle, Standby
These displayed contents differ according to the machine tool builder. Display
This displays the tool center point coordinates, handle interruption 2.24 Tool Center Point
amount (tool axis movement), and tool center point speed. Display
(Note) If the 5-axis related options (tool center point control, tool
length compensation along the tool axis, tool handle feed &
interrupt) are not mounted, these menus are not displayed.
This displays commanded/actual rot speed values of all the spindles. 2.25 All Spindles'
Rotation Speed Display
I - 43
2. Monitor Screens
2.1.1 <Auto/MDI> and <Manual> Counter Display
The following counters are displayed on <Auto/MDI> and <Manual>.

<Auto/MDI>
5-axis related 5-axis related
Layout specifications specifications Remarks
disabled enabled
Upper left of Relative position Tip workpiece This can be changed with "#8901 counter type 1".
screen position
Lower left of Program position Program position This can be changed with "#8902 counter type 2".
screen
Upper right of Remaining Remaining This can be changed with "#8903 counter type 3".
screen command command
Lower right of Next command Next command This can be changed with "#8904 counter type 4".
screen
<Manual>
5-axis related 5-axis related
Layout specifications specifications Remarks
disabled enabled
Left of screen Relative position Tip workpiece This can be changed with "#8905 counter type 5".
position
Right of Machine position Machine position This can be changed with "#8906 counter type 6".
screen
2.1.2 Changing Between <Auto/MDI> and <Manual>
The correspondence between the mode selection switch settings and display contents on the left side of the
screen is as follows.
Mode selection switch setting Screen display

No mode Auto/MDI
Memory
Tape
MDI
Jog Manual
Handle
Step
Manual arbitrary feed
Reference point return
Automatic dog-less reference point return
Rapid traverse
Jog + handle
Rapid traverse + handle mode
I - 44
2. Monitor Screens
2.2 Operation Search
On this screen, the program can be called from the program storage site, such as a memory, by designating
the program (program No.) to be automatically run and the program start position (sequence No., block No.).
In 70 series, only the memory, the serial, and the memory card can be used for the input/output device.
(1)
(2)
(3)
(4)
Display items

(1) Device name, directory This displays the device name and directory designated when the program was
display selected.
(2) Capacity display This displays the capacity of the device displayed in (1).
(3) List of directories and files This displays a list of the contents contained in the device or directory
displayed in (1).
Use ½ and ¾ to scroll the displayed list.
If the device is an HD, FD, memory card or DS, the file update date/time is displayed
in the <Date/Comment> field. For the NC memory, the machining program comment
is displayed.
Whether to show or hide the comment field can be selected by pressing the
Comment nondisp menu. When the comment field is hidden, the file name field will
be enlarged. (Up to 13 characters can be displayed in the file name field when the
comment is shown, and 32 when the comment is hidden.) If the file name exceeds the
maximum number of characters, "*" will appear at the last character.
(4) Input area This displays the input key details.
I - 45
2. Monitor Screens
Menus

This selects the device for searching for the program. C 2.2.1 Executing an
Memory
When a device with directory is selected, the route is selected first. Operation Search
(In 70 series, only "Memory", "Serial", and "Memory card" are
displayed.) C
HD
C
Serial
Memory C
card
C
DS
C
FD
List This updates the list contents. (The latest contents of the currently C
update selected device and directory are listed.)
Sort This changes the method that the list is sorted. C 2.2.3 Changing the
change Sorting Method
This changes whether to show or hide the comment field in the list. B 2.2.2 Changing Whether
Comment
When the comment field is hidden, the file name field will be enlarged. to Show or Hide the
nondisp
Comment Field
This closes the pop-up window and quits this function. C
Close
(Note 1) Some items may not be displayed depending on the device.
{: Displayed ×: Not displayed.

Device
Memory HD Serial Memory card DS FD
Display item
Prog entry { { × { { {
Remain { × × × × ×
Memory side { { × { { {
Remain { { × { { {
List { { × { { {
(Note 2) When using serial, the port number set with parameter "#9005 TAPE MODE PORT" is connected,
and search.
I - 46
2. Monitor Screens
2.2.1 Executing an Operation Search
Operation method
(1) Select the part system to run with the The selected part system appears on the upper left of
$<->$ keys. the screen.
(2) Press the main menu Search . The sub-menu appears.

The list appears as a pop-up window.
(3) Select the device. The selected device name and route directory (HD:/)
(Example) HD appear in the Device name, Directory display field.
(4) Using the ↑, ↓, ½ and ¾ keys, move the The following is displayed.
cursor to the directory containing the file to
be set.
If the list contents differ from the actual device or directory, press the menu List Update .
(5) Press the INPUT key. The active window changes to the directory.
(6) Using the ↑, ↓, ½ and ¾ keys, move the

cursor to the target machining program.
(7) Press the INPUT key. The search starts.

When the search is completed, the message "Search
Complete" appears.
The searched device and program position appear in
the field for displaying the machining program
currently being executed.
The list closes, and the main menu appears again.
I - 47
2. Monitor Screens
When designating the sequence number and block number and searching for the program, input the search
conditions in the input area. he program No. is categorized according to the presence of an extension.
Input details Program No. Sequence No. Block No.

1001/1/2 O1001 N1 B2
1001.PRG/1/2 O1001.PRG N1 B2
/1/2 (Currently searched O No.) N1 B2
1001//2 O1001 N0 B2
1001/1 O1001 N1 B0
1001 O1001 N0 B0
/1 (Currently searched O No.) N1 B0
//2 (Currently searched O No.) N0 B2
(Note 1) Program after operation search
(a) Operation search is cancelled if the following operations are carried out on the Edit screen after
operation search. Execute restart search in this case.
• If the searched program is erased.
• If the searched sequence No. is erased.
• If the block corresponding to the searched block No. is erased.
(b) Operation search cannot be executed in another block during MDI operation even if the block is
stopped.
Wait for MDI operation to end or reset the NC before searching.
(Note2) A program with 33 or more file name characters cannot be searched.
I - 48
2. Monitor Screens
2.2.2 Changing Whether to Show or Hide the Comment Field
The file name field can be extended by changing whether to show or hide the comment field.
Operation method
(1) Press the menu "Comment nondisp". The file name is displayed up to 32 alphanumeric
characters and symbols after the comment field
disappears.
The menu is highlighted.
(2) Press the highlighted "Comment nondisp" The comment field appears, and the file name is
again. displayed up to 15 alphanumeric characters and
symbols.
The menu highlight returns to normal.
(Example) When the file name is "123456789A123456789B123456789C12"

"Comment display" is validated: The file name display is omitted and "*" is attached.
"Comment display" is invalidated: The file name is displayed up to 32 alphanumeric characters and
symbols.
(Note 1) The set status is held even if the NC power is turned OFF.
(Note 2) The set status is common for list view of operation screen, restart search screen, etc.
(Note 3) The cursor moves to the head when display/non-display in the comment field is switched.
I - 49
2. Monitor Screens
2.2.3 Changing the Sorting Method
Sorting method changes to 1→2→3→4→5→1 • • • • every time the Sort change menu is pressed.
The selected sorting method is also displayed in the list on the ther screens. The method is common for all
the devices, as well. The sorting method will be held even after the power is turned OFF and ON.
Up to 64 files (Including current directory "." and one directory above "..") can be sorted within a directory. If
exceeds 65 files, the Sort change menu is displayed in gray and changing the sorting method is impossible.
In this case, the sorting method is "2. File name character code ascending order".
No. Sorting method Priority

1 File name No. ascending order 1. "." for current directory, ".." for one directory above
2. Numerical value (excluding the case where "0" is put at the
beginning) ascending order
3. Character code ascending order
2 File name character code 1. "." for current directory, ".." for one directory above
ascending order 2. Character code ascending order
3 File name character code 1. Character code descending order
descending order 2. "." for current directory, ".." for one directory above
4 Comment ascending order "Date/comment" character code ascending order
5 Comment descending order "Date/comment" character code descending order
(Note 1) The character code ascending (descending) order is the method in which file names are compared
one by one using the ASCII code.
Example: If the ascending order is applied, the appropriate order would be 1→A as "1" equals to
"0x31" and "A" equals to "0x41".
(Note 2) When the device is "Memory", display for "current directory" and "one directory above" is not
available.
(Note 3) When comments are the same, sorting is carried out by the file name character code ascending
(descending) order.
(Note 4) "Date/comment" for the devices other than "Memory" are compared using character string only.
Thus, the order will not be one by the actual date.
(Note 5) Sorting method cannot be changed in memory mode.
I - 50
2. Monitor Screens
2.3 Restart Search
2.3 Restart Search
If machining is temporarily stopped due to tool breakage, etc., the program restart function searches for the
block of the machining program to be restarted, and restarts machining from that block.
There are two types of restart, type 1 and type 2.
Restart method Details
Restart type 1 After machining is reset due to a tool breakage, etc., machining is restarted from the designated
sequence number and/or block number.
Only the program which had been executed just before can be restarted.
Even after the power is turned ON again, the program can be restarted if the program has been
executed before the power supply is turned OFF.
(Note 1) In case that NC has been reset or the power supply has been turned OFF while fixed
cycle, custom fixed cycle, machine tool builder macro, or macro interruption is
executed, the search with no input to the setting will be performed for each source
program.
(Note 2) When the user macro is executed, the user macro execution position is searched.
Restart type 2 After machining program is stopped due to a holiday, etc., and the power is turned OFF and ON,
machining is restarted from the designated sequence number and/or block number.
Automatic top A top search must be executed from the screen. Then, command a sequence
search OFF No. and block No., and restart a program.
Automatic top A top search may not be executed from the screen. A top search is automatically
search ON executed, so it is not necessary to execute a top search from the screen.
Command a sequence No. and block No., and restart a machining.
An arbitrary program can be restarted by designating the program No.
When a program No. is omitted, the program currently searched is restarted.
The validity of the automatic top search can be changed with control parameter "#8914 Auto Top search".
I - 51
2. Monitor Screens
2.3 Restart Search
Screen transition
<Top search screen> (Note)
[Top search]
[Search exec]/[Top search]/[INPUT]
<Main screen> <File setting screen>

[File set]
[Retn]/File input operation
<MSTB History screen>
[MSTB history]
[MSTB history]
(Note) In the following cases, the screen cannot be switched to top search screen.
• Restart type 1
• The parameter "#8914 Auto Top search" is "1" (automatic top operation)
I - 52
2. Monitor Screens
2.3 Restart Search
2.3.1 Main Screen

The type 1 and type 2 restart search can be executed from the Main screen.
(1)
(2)
(3)
(4)
(5)
(6)
Display items

(1) Device and directory This displays the device and directory where the searched machining program is
display located.
(2) Research position This displays the researched main program position (program No., sequence No.,
block No.).
(3) Restart type This displays the restart search type.
(4) Position when restart This displays the position on the local coordinate system when the restart search is
search is completed completed.
(5) Remaining distance when This displays the remaining distance when the restart search is completed.
restart search is
completed
(6) Input area This displays the input key details.
I - 53
2. Monitor Screens
2.3 Restart Search
Menus

This starts the restart search based on the designated device, C
Search
exec directory, program number (O), sequence number (N), block number
(B) and number of block execution times (P).
This changes to the pop-up window for executing top search, and B 2.3.2 Top Search Screen
Top enables top search.
search When the type 1 is selected or the parameter "#8914 Auto Top search"
is set, this menu cannot be selected.
This selects the restart search type. Restart search is executed with B
Type1 the highlighted restart type.
The type 1 or type 2 menu is always highlighted.
Type2 When restart search is executed, the selected restart type is displayed
at the display item "(3) Restart type".
This changes to the pop-up window for setting the file, and enables B 2.3.3 File Setting Screen
File set the file to be selected.
This opens the MSTB history screen as a pop-up window. B 2.3.4 MSTB History
The M, S, T and B command used in the machining program are listed Screen
MSTB on the MSTB history screen. If the cursor is moved to the listed M, S,
history
T or B command and the INPUT key is pressed, that command will
be executed.
Close
I - 54
2. Monitor Screens
2.3 Restart Search
2.3.2 Top Search Screen
Display items
Same as "2.2 Operation Search".
Menus

This starts the restart search based on the designated device, C
Search
exec directory, program number (O), sequence number (N), block number
(B) and number of block execution times (P).
When the menu is highlighted, it indicates that the top search pop-up B
window is open. When this is highlighted, it indicates that the top
Top
search search pop-up window is open. If pressed again when highlighted, the
top search pop-up window closes, and the main pop-up window
opens.
List This updates the list details. (A list of the latest details of the currently C
update selected device and directory is displayed.)
This displays the device menu. Select which device program to search C
Device
select for from this menu. If a device having a directory is selected, the root
is selected first.
Sort This updates the list sorting method. C 2.2.3 Changing the
This changes whether to show or hide the comment field in the list. C 2.2.2 Changing Whether
Comment
nondisp
Comment Field
I - 55
2. Monitor Screens
2.3 Restart Search
2.3.3 File Setting Screen
Display items
Same as "2.2 Operation Search".
Menus

Select the device to search program. C
Memory
When a device other than memory is selected, the root is selected
first.
(In 70 series, only "Memory" and "Memory card" are displayed.) C
HD
C
M-Card
C
DS
C
FD
List This updates the list details. (A list of the latest details of the currently C
update selected device and directory is displayed.)
Sort This updates the list sorting method. C 2.2.3 Changing the
This returns the main menu. C
Retn
Comment This changes whether to show or hide the comment field in the list. B
nondisp When the comment field is hidden, the file name field will be enlarged.
I - 56
2. Monitor Screens
2.3 Restart Search
2.3.4 MSTB History Screen
(1)
Display items
Display items Details

(1) MSTB history The M, S, T and B command used in the machining program are listed.
Up to 35 M commands, 3 commands each for S1 to S4, 3 T commands and 3 B
commands are displayed.
Menus

When this is highlighted, it indicates that the MSTB history pop-up B
MSTB window is open. If the menu is pressed when this menu is highlighted,
history the system will close the MSTB history pop-up window, and the main
pop-up window opens.
I - 57
2. Monitor Screens
2.3 Restart Search
2.3.5 Operation Sequence for Program Restart

There are two types of restart, type 1 and type 2.
Restart type 1
When feed hold has been applied and reset because the tool has broken, etc., restart with Restart type 1.
Start
Machining program
Press the feed hold button and retreat to the Feed hold reset
tool change position by manual means or MDI.
Press the RESET key and suspend the present Machining restart
processing.
If the tool compensation amount (tool length,

tool radius) is changed, change the tool on
Replace with a new tool. tool compensation screen.
Operation on program restart screen

Search the block to be restarted.
(Refer to "2.3.6 Executing Restart Search (Restart type 1)") The following items are displayed when
restart search is completed.
• Remaining distance when the restart
Turn the program restart switch ON. search is completed
• Restart position (on local coordinates)
• Each command value of the SMTB
functions
Execute the manual numerical value command
(S,M,T,B) "RP" is displayed for the axes that have
(Refer to "2.3.11 Executing the MSTB Commands") moved to the restart position. After this, the
In the manual (JOG/rapid traverse) mode, move axis does not move in either the + or -
the axes to the restart return position. direction.
(Refer to "2.3.10 Returning to the Restart Position")
Turn the program restart switch OFF.
Return to the automatic operation mode.

If the cycle starts when the "Automatic
return by program restart" parameter
Press the cycle start button. ("#1302 AutoRP") is ON, the processing is
restarted after all axes return to the restart
position at the same time.
End (Refer to "2.3.10 Returning to the Restart Position")
(Note 1) When single block signal is OFF, the machining is restarted without stopping temporarily after the
axes return to the restart position. (The cycle starts when the automatic return by program restart is
valid.)
I - 58
2. Monitor Screens
2.3 Restart Search
(Note 2) Execute Reset & Rewind for resetting.

(Note 3) Restart & Search must be carried out with Restart Type 2 when the power has been turned ON
again.
If Restart Type 1 is selected, "Search error" occurs.
(Note 4) Restart Search is not possible for a program with 33 or more file name characters.
I - 59
2. Monitor Screens
2.3 Restart Search
Restart type 2
If a machining program differing from the machining program to be restarted was run before starting restart
search, restart with restart type 2.
When the coordinate system of the automatic operation last time and the coordinate system of the machining
restart are changed, it is possible to restart.
(Note) The necessary matters for starting the machining program, such as setting the coordinate system,
must be completed before starting restart search.
Start Machining program Running of other

program
Machining stop
In the MDI mode, set the coordinate system to

be used when starting the program to be
Machining
restarted. restart
If the command at the head of the program is

Move each axis to the program start position. an incremental command or G92 command,
and none of the axes are at the program start
position, the program does not restart
properly.
Search for the block to be restarted. Operation on program restart screen

(Refer to "2.3.7 Executing Restart Search (Restart type 2)")
The following items are displayed when
restart search is completed.
• Remaining distance when the restart
Turn the program restart switch ON. search is completed
• Restart position (on local coordinates)
• Each command value of the SMTB
Execute the manual numerical value command functions
(S,M,T,B)
(Refer to "2.3.11 Executing the MSTB Commands") "RP" is displayed for the axes that have
In the manual (JOG/rapid traverse) mode, move moved to the restart position. After this, the
axis does not move in either the + or -
the axes to the restart return position.
direction.
Turn the program restart switch OFF.
Return to the automatic operation mode.
If the cycle starts when the "Automatic

Press the cycle start button. return by program restart" parameter
("#1302 AutoRP") is ON, the processing is
restarted after all axes return to the restart
End position at the same time.
(Note 1) When single block signal is OFF, the machining is restarted without stopping temporarily after the
axes return to the restart position. (The cycle starts when the automatic return by program restart is
valid.)
(Note 2) Restart Search is not possible for a program with 33 or more file name characters.
(Note 3) When the searched program do not exist, the operation message "Search error" appears.
I - 60
2. Monitor Screens
2.3 Restart Search
2.3.6 Executing Restart Search (Restart Type 1)
When feed hold has been applied and reset because the tool has broken, etc., restart with Restart type 1.
Operation method
(Example) When tool breakage during execution of O1000 N7 occurred, and restarting from the O1000 N6
block
(1) Press the feed hold button and retreat to

the tool change position by manual means
or MDI.
Press the reset key and suspend the
present processing.
(2) Replace with a new tool.
(3) When using tape operation, index the top

of the tape.
(4) Press the main menu Resrart . The submenu appears.

The main screen for restart search appears as a
pop-up window.
(5) Set the position to restart search in the Delimit the ONB number in the setting area using /.
setting area. <When O No. was attached>
The main or sub program is targeted.
(Ex.) 1000/6/0
<When O No. was not attached>
The program currently searched is targeted.
(Ex.) /6/0
(Note) When the INPUT key is pressed without
entering data in the input area, restart search
will be carried out for the last execution block.
(Type 1 only)
(6) Press the INPUT or Search exec Restart search is executed.

menu. The message "In restart search" appears during the
search process, and the message "Restart search
complete" appears when completed.
Each axis' restart position and the restart remaining
distance are displayed.
When the MSTB history menu is pressed, the
MSTB history screen will open as a pop-up window,
and the M, S, T, B command used in the machining
program will be listed.
I - 61
2. Monitor Screens
2.3 Restart Search
2.3.7 Executing Restart Search (Restart Type 2)
If a machining program differing from the machining program to be restarted was run with tape, memory or
HD operation before starting restart search, restart the respective machining program with restart type 2.
The restart type 2 operation sequence is the same as restart type 1, but necessary matters for starting the
machining program, such as setting the coordinate system, must be completed before starting restart search.
When the parameter "#8914 Auto Top search" is "0", execute the top search for the machining program.
Operation method (When the parameter "#8914 Auto Top search" is "0")
(Example) When restarting from subprogram O123 N6 B2 called from main program O1000
(1) Turn the power ON, and return all axes to

the reference position.
(2) In the MDI mode, set the coordinate

system to be used when starting the
program to be restarted.
(3) Move each axis to the program restart

position.

of the tape.
(5) Press the main menu Restart search . The submenu appears.
pop-up window.
(6) Press the Type 2.
(7) Press the sub-menu Top search . The window for top search appears as a pop-up
window.
(8) Using the ↑ , ↓ , ½ and ¾ keys, move the Set the cursor to 1000.
(9) Press the INPUT key. The top search starts.

When the top search is completed, the message
The search can be executed by pressing "Search Complete" appears.
the menu Search exec instead of the The top search pop-up window closes, and the main
INPUT key. screen for restart search appears as a pop-up window.
I - 62
2. Monitor Screens
2.3 Restart Search
(10) Set the position to restart search in the Delimit the ONBP number in the setting area using /.
The restart search is executed at designated position
by NBP No. with the set O No. at the head.
(Ex.) 123.PRG/6/2/1
(Ex.) /6/2/1
P sets the number of times that the block targeted for the restart search appears.
For example, if a block in a subprogram is searched, and the subprogram is called out several times,
the block to be searched is also executed several times. Thus, which execution block to be searched
must be set. (If "0" is set, it is handled in the same manner as "1".)
To search the first execution block, or to search for a block executed only once, this item does not
need to be set.

I - 63
2. Monitor Screens
2.3 Restart Search
Operation method (When the parameter "#8914 Auto Top search" is "1")
(Example) When restarting from subprogram O123 N6 B2 called from main program O1000
(1) Turn the power ON, and return all axes to

the reference position.
(2) In the MDI mode, set the coordinate

system to be used when starting the
program to be restarted.
(3) Move each axis to the program restart

position.

of the tape.
(5) Press the main menu Restart search . The submenu appears.
pop-up window.
(6) Press the Type 2.
(7) Press the sub-menu File set . The window for file set appears as a pop-up window.
(8) Using the ↑ , ↓ , ½ and ¾ keys, move the Set the cursor to 1000.
(9) Press the INPUT key. The screen for restart search appears as a pop-up
window.
I - 64
2. Monitor Screens
2.3 Restart Search
(10) Set the position to restart search in the Delimit the ONBP number in the setting area using /.
The restart search is executed at designated position
by NBP No. with the set O No. at the head.
(Ex.) 123.PRG/6/2/1
(Ex.) /6/2/1

I - 65
2. Monitor Screens
2.3 Restart Search
2.3.8 Changing the Device
Operation method
(1) Press the submenu File set . The window for file setting appears as a pop-up
window.
(2) Select the device, and press the menu The selected device name and root directory (HD:/)
key. appear in the Device name and Directory display field.
(Example) HD
(Note) In 70 series, only the memory and the memory card can be used for the input/output device.
2.3.9 Changing the Directory with the Main Screen
Operation method
(1) Press the submenu File set . The window for file setting appears as a pop-up
window.
(2) Using the ↑ , ↓ , ½ and ¾ keys, move the The following is displayed.
cursor to the directory to be moved.
If the list contents differ from the actual device or directory, press the menu List Update .
(3) Press the INPUT key. The directory changes, and the contents of the
designated directory appear in the list.
The moved directory appears in the directory display
field.
(4) Repeat steps (2) and (3).
(5) After changing the directory, press the The restart search main window opens as a pop-up
Retn or CANCEL key. window.
I - 66
2. Monitor Screens
2.3 Restart Search
2.3.10 Returning to the Restart Position

The axis is returned to the restart position after restart search is completed.
The method for returning to the restart position (manual/automatic) can be selected with the parameters
"#1302 AutoRP".
0 : Manual restart position return
1 : Automatic restart position return
Operation method (manual restart position return)
(1) Turn the restart switch ON.
(2) Enter the manual (JOG/rapid traverse)

mode.
(3) Move the axis in the restart return The restart position and "RP" appear sequentially from the
direction. axes that have been returned. The Restart remaining
distance is "0".
(4) When all axes have been returned, turn

the restart switch OFF.
(Note 1) When the restart switch is ON, move the axis in the same direction as the restart direction. If moved
in the reverse direction, the operation error "M01 R-pnt direction illegal" occurs. If the tool needs to
be retracted once, such as if the tool is interfering with the workpiece, turn the restart switch OFF
and retract the axis manually.
(Note 2) After restart position return is completed, the axis cannot be moved if the restart switch is ON. If the
axis is moved, the operation error "M01 restart switch ON" occurs.
(Note 3) If even one axis has not completed return to the restart position at cycle start, the error "T0112
Restart pos. return incomplete" occurs. Note that if the axis has been returned to the restart position
once and is not at the restart position during cycle start, the alarm does not occur.
(Note 4) If the axis to be returned to the restart position is a machine lock axis, the operation error "M01
program restart machine lock" occurs. Release the machine lock before returning to the restart
position.
(Note 5) If the restart switch is turned to ON after the axis is returned to the restart position with the restart
switch OFF, "PR" may not be displayed. Return to the restart position after the restart switch is
turned ON.
(Note 6) After restart search had been completed, if the movement command is issued by MDI before
automatic restart position return has been started, the program error (P48) occurs. Perform the
operation again after reset.
I - 67
2. Monitor Screens
2.3 Restart Search
(Note 7) After restart search had been completed, if the T command different from the program is issued by
MDI before the searched program has been started, the program error (P48) may occur. Perform
the operation again after reset. T commands which result in errors are shown below. (Only L
system)
(1) When "#1100 Tmove" = "0"
T command that selects a tool with different tool length/wear amount than the tool selected by
the program
(2) When "#1100 Tmove" = "1"
A program error will not occur by T command.
(3) When "#1100 Tmove" = "2"
T command that selects a tool with different wear amount than the tool selected by the program
(Note 8) After restart search had been completed, if the handle interruption is performed before the searched
program has been started, always the same operation as manual absolute ON is executed
regardless of "Manual absolute" signal.
Automatic restart position return
If the parameter "#1302 AutoRP" is set to "1", each axis returns to the restart position with dry run at cycle
start. Machining restarts after returning. The order that the axes return follows parameter "#2082 a_rstax".
(Note 1) Manually move the axis to a position where the tool does not interfere with the workpiece before
starting the cycle.
(Note 2) Even if the parameter "#1302 AutoRP" is set to 1, the axes can be returned manually to the restart
position by turning the restart switch ON. In this case, move the axes in the order of manual restart
position return → automatic restart position return. After completing automatic restart position return,
if the operation is stopped temporarily and the restart switch is turned ON, the operation error "M01
restart switch ON" occurs.
(Note 3) Once the axis has been manually returned to the restart position, if it is moved from the restart
position, it will not return to the restart position even if automatic restart position return is executed.
(Note 4) The axis for which parameter "#2082 a_rstax" is set to 0 does not return to the restart position. Note
that if 0 is set for all axes, all axes simultaneously return to the restart position. Designate the axes
in part system units. If the axis for which parameter "#2082 a_rstax" is set to 0 has not completed
manual restart position return when automatic restart position return is started, the error "T0112
Restart pos. return incomplete" occurs.
(Note 5) After automatic restart position return had been started, if the automatic start is executed during
MDI mode before not all axes have yet to complete automatic restart position return, the error
"T0112 Restart pos. return incomplete" occurs.
(Note 6) After restart search had been completed, if the movement command is issued by MDI before
automatic restart position return has been started, the program error (P48) occurs. Perform the
operation again after reset.
(Note 7) After restart search had been completed, if the T command different from the program is issued by
MDI before the searched program has been started, the program error (P48) may occur. Perform
the operation again after reset. T commands which result in errors are shown below. (Only L
system)
(1) When "#1100 Tmove" = "0"
T command that selects a tool with different tool length/wear amount than the tool selected by
the program
(2) When "#1100 Tmove" = "1"
A program error will not occur by T command.
(3) When "#1100 Tmove" = "2"
T command that selects a tool with different wear amount than the tool selected by the program
(Note 8) After restart search had been completed, if the handle interruption is performed before the searched
program has been started, always the same operation as manual absolute ON is executed
regardless of "Manual absolute" signal. When manual interruption is executed to the automatic
restart position return completed axis, the axis never returns the automatic restart position again.
(Note 9) When an axis moved to return is operated manually, the axis cannot return to correct position.
I - 68
2. Monitor Screens
2.3 Restart Search
2.3.11 Executing the MSTB Commands

If the MSTB history menu is pressed after restart search is completed, the MSTB commands used for
machining program appear.
When the cursor is moved to the listed M, S, T, B commands and the INPUT key is pressed, that
command will be executed.
Up to 35 M commands, 3 commands each for S1 to S4, 3 T commands and 3 B commands are displayed. If
many MSTB commands are used for machining, the MSTB commands used at first will not appear.
Operation method
(1) Press the submenu MSTB history . The pop-up window changes to the MSTB history
window.
The MSTB commands used for machining program
are listed.
(2) Using the ↑ , ↓ , → and ← keys, move the

cursor to the position of the data to set.
(3) Press the INPUT key. The designated command is executed. A value, which
has been commanded once, is displayed in gray. The
cursor will move to the next item.
(4) Repeat steps (2) and (3).
(5) When completed with all settings, press The MSTB history pop-up window closes and the
the Close or MSTB history menu. restart search main window appears as a pop-up
window.
I - 69
2. Monitor Screens
2.4 Program Edit
2.4 Program Edit
The machining programs are edited. When the main menu Edit is pressed, the operation searched
program (MDI program for MDI mode) appears.
If no program has been searched or tape operation has been executed, the edit window will not open.
When the program is edited, the key input data is directly written into the program display area. All data is
overwritten from the cursor position. "Editing" appears on the right side of the file name display when the input
starts. When the INPUT key is pressed, the program is saved in the NC memory and the "Editing"
message disappears.
Refer to "4.2 Program edit" for details.
I - 70
2. Monitor Screens
2.5 Trace
2.5 Trace
This function illustrates the actual machine's movement path or tool center point movement path, and draws
the actual machine movement.
This allows the machine operation to be monitored during machining.
The programs that can be traced are operation searched machining programs (MDI program for MDI mode).
If no program has been operation searched, the trace window will not open.
Using All display menu, normal display and whole display modes can be switched.
(Note 1) The trace function is an additional specification. The graphic trace option is required.
(Note 2) The tool center point trace function is an additional specifications. The 5-axis related options (tool
center point control, tool length compensation along the tool axis, tool handle feed & interrupt) are
required.
■Normal display (full-screen display mode is OFF)

< Drawing area >
(1)
(2)
(3)
(4)
(5)
< Drawing area: 2-plane > < Input area displayed >
(6)
I - 71
2. Monitor Screens
2.5 Trace
■Full-screen display (full-screen display mode is ON)

< Drawing area >
(1)
(5)
(3)
(7)
(2)
(4)
Display items

(1) Counter The counter of the axis targeted for the trace drawing is displayed. The three axes
which are displayed are set with the parameters.
The counter selected by the menu "Counter type" is displayed.
The counter type displayed can be set for [Trace ON] and [Tip traceON] separately.
And the setting is held even after the power is turned OFF and ON.
The default setting is as follows.
[Trace ON] : depends on the setting of "#1231 set03 (bit4)". (0: The machine
position counter (Mach posn), 1: The workpiece coordinate position
counter (Work co posn))
[Tip traceON] : The machine position of the tool center point counter (Tip Mach posn)
(2) Display mode The plane currently being drawn is displayed.
(3) Trace drawing area This area is used to draw the tool path as graphics.
The zero point to be displayed is as follows.
Machine position trace mode : The zero point can be switched between the machine
position zero point and workpiece coordinate position
zero point with parameter "#1231 set03".
Tool center point trace mode : The machine position of tool center point zero point
(4) Scale The display range scale is displayed.
(5) Machining time display The time required for machining is calculated and displayed. Nothing is displayed
during tracing.
(6) Input area The input area appears when the menu Display range and Display mode are
pressed.
The scale value and display mode are set.
The input area is hidden when the INPUT key is pressed.
(7) Program display This displays the contents of the machining program currently being executed.
I - 72
2. Monitor Screens
2.5 Trace
Menus

This activates the trace mode. If any program is currently running, the B 2.5.1 Displaying the
Trace machine position path is traced from the current position. If this menu Machine Position Trace
ON is pressed during the machine position trace mode, the trace mode
will be turned OFF.
This activates the tool center point trace mode. If any program is B 2.5.3 Displaying the Tool
currently running, the path of tool center point machine position path is Center Point Trace
Tip traced from the current position. If this menu is pressed during the tool
traceON center point trace mode, the trace mode will be turned OFF.
Note that this menu does not appear if the 5-axis related option is
OFF.
This erases the data in graphic drawing area displayed on the screen. C
Erase
This changes the graphic drawing display range. C 2.5.5 Changing the
When this menu is pressed, the menu changes to the display range Display Range
Display change menu.
range
When the display range is changed, the graphic data displayed on the
screen is erased.
This changes the drawing plane. C 2.5.6 Changing the
When this menu is pressed, the menu changes to the display mode Display Mode
change menu.
Display
mode There are three types of graphic display modes: 1-plane, 2-plane and
3D.
When the drawing plane is changed, the graphic data displayed on
the screen is erased.
All This switches the normal display mode and the full-screen display B 2.5.8 Switching the
display mode. Full-screen Display
Mode
This displays the machining program being executed on the graphic B
Program drawing area.
display This menu can be selected only when the full-screen display mode is
applied.
This sets the viewpoint angle for the 3D display mode. C 2.5.7 Changing the
When the viewpoint angle is changed, the graphic data displayed on Display Angle
Rotate
the screen is erased.
Note that this menu can be used only in the 3D display mode.
The display range (scale and display position) is automatically set C
from the machine movable area. The machine movable area is set
Std with the parameters "#2013 OT-" and "2014 OT+" (software limit).
range
screen is erased.
This displays the selected counter. For each trace mode, the counter C
type can be set separately. And the setting is held after the power is
turned OFF and ON. However, if the [Trace ON] or [Tip traceON]
menu is not highlighted, this is displayed in gray and cannot be
selected.
The following counters can be selected.
• Relat posn (Related position counter)
• Work co posn (Workpiece coordinate position counter)
Counter • Machine posn (Machine position counter)
type
• Remain command (Remain command counter)
• Next command (Next command counter)
• Program posn (Program position counter)
• Tip wk posn (Tool tip workpiece position counter)
• Tip machine (Machine position of tool center point counter)
• Pulse (Tool axis movement counter)
(Note) During the trace mode, "Tip wk posn", "Tip machine" and
"Pulse" are cannot selected.
Close
I - 73
2. Monitor Screens
2.5 Trace
2.5.1 Displaying the Machine Position Trace
Operation method
(1) Press the main menu Trace ON . • The Trace ON menu is highlighted.
If Tip TraceON is highlighted, unhighlight it.
• The machine position appears in the drawing area
as a tool mark.
• The counter selected by Counter type menu is
displayed at the counter.
• The message "Tracing" appears.
After this, the machine position path is drawn with
graphics in the trace mode.
(Note) If graphic check (2D) is executed, the "Trace
ON" status is cancelled.
The path where the machine position or tool center

position is drawn with graphics.
The path is drawn with a solid green line.
I - 74
2. Monitor Screens
2.5 Trace
2.5.2 Canceling the Machine Position Trace
Operation method
(1) Start tracing with the machine position.
(2) Press the main menu Trace ON . • The Trace ON menu is unhighlighted.
• The tool mark in the drawing area is erased.
• The message "Tracing" is erased.
(Note) Even if the menu is unhighlighted, the
displayed counter type does not change.
2.5.3 Displaying the Machine Position of the Tool Center Point Trace
Operation method
(1) Press the main menu Tip TraceON . • The Tip TraceON menu is highlighted.
If Trace ON is highlighted, unhighlight it.
• The tool center point appears in the drawing area as
a tool mark.
• The counter selected by Counter type menu is
displayed at the counter.
• The message "Tracing Tip Position" appears.
After this, the tool center point path is drawn with

graphics in the tool center point trace mode.
(Note) If graphic check (2D) is executed, the "Tip
Trace ON" status is cancelled.
2.5.4 Canceling the Machine Position of the Tool Center Point Trace
Operation method
(1) Start tracing with the tool center point.
(2) Press the main menu Tip TraceON . • The Tip TraceON menu is unhighlighted.
• The tool mark in the drawing area is erased.
• The message "Tracing Tip Position" is erased.
(Note) Even if the menu is unhighlighted, the
displayed counter type does not change.
I - 75
2. Monitor Screens
2.5 Trace
2.5.5 Changing the Display Range

The graphic drawing's scale can be enlarged or reduced, and the position moved or centered.
Operation method (Enlarging the and reducing the drawing)
(1) Press the Display range key. A white frame indicating the display range appears on
the screen.
The display range input mode is activated, and the
following menu appears.
Zoom Zoom Center-

Up Down Left Right
in out ing
(2) Press the menu Zoom in or Zoom out. The size of the white frame changes according to the
key operations.
To enlarge the figure:
Press the menu Zoom In or the -
key.
To reduce the figure:
Press the menu Zoom out or the +
key.
A solid-line frame appears with respect to

the original scale when enlarging, and a
dotted-line frame appears when reducing.
(3) Press the INPUT key. The display scale is changed.

By changing the display scale, the graphic data
displayed on the screen is erased.
It is also possible to change the display scale by
setting a scale value in the input area.
(Note) The changed scale value is held even after the power is turned OFF and ON.
I - 76
2. Monitor Screens
2.5 Trace
Operation method (Changing the drawing display position)
the screen.
Zoom Zoom Center-

Up Down Left Right
in out ing
(2) Press the Up , Down , Left , Right The cursor () indicating the center of the display and
menu or cursor movement keys ↑ , ↓ , the frame line move up, down, left and right according
←, → . to the key operations.
(3) Press the INPUT key. The display position changes so that the cursor
position () is the center of the area.
By changing the display position, the graphic data
displayed on the screen is erased, however, the scale
value is not changed.
(Note 1) When changing the display range in the 2-plane display mode such as "XY/XZ", the display range
(scale and display position) for the upper and lower areas changes in the same manner.
The operation method is the same as the 1-plane display mode.
The white-framed display range in the upper and lower areas simultaneously move to the left/right
when the Left , Right keys are pressed.
The white-framed display range of either upper or lower areas moves up and down when the
Up , Down keys are pressed.
Which frame to be moved up/down can be changed with the page key.
I - 77
2. Monitor Screens
2.5 Trace
Operation method (Centering)
the screen.
Zoom Zoom Center-

Up Down Left Right
in out ing
(2) Press the Centering key. The display position is changed so that the current
machine position appears in the center of the drawing
area.
When display position is changed, the graphic data
(Note 1) In the 2-plane display mode such as "XY/XZ", centering is applied for the upper and lower areas.
I - 78
2. Monitor Screens
2.5 Trace
2.5.6 Changing the Display Mode

The graphics display mode includes the 1-plane, 2-plane and 3D mode. When the menu
Display mode is pressed and the following display mode menu is selected, the axis configuration of each
plane changes, and the menu display returns to the original state. It is also possible to change the display
mode by setting the axis name to the input area.
(Note 1) When display mode is changed, the graphic data displayed up to that point are erased.
(Note 2) The set display mode is held even after the power is turned OFF and ON.
(Note 3) The display mode can be set independently for the trace function and program check function.
These settings are not sequenced.
(Note 4) The menu axis names XYZ correspond to the base axis IJK. X = base axis I, Y = base axis J, and Z
= base axis K.
Display mode menus
Menu Details Type

This changes to the 1-plane display mode configured of X-Y. C
XY The X axis is displayed as the horizontal axis, and the Y axis is displayed as
the vertical axis.
This changes to the 1-plane display mode configured of Y-Z. C
YZ The Y axis is displayed as the horizontal axis, and the Z axis is displayed as
the vertical axis.
This changes to the 1-plane display mode configured of X-Z. C
XZ The X axis is displayed as the horizontal axis, and the Z axis is displayed as
the vertical axis.
This changes to the 2-plane display mode configured of X-Y and X-Z. C
XY/XZ The X axis is displayed as the horizontal axis, and the Y axis and Z axis are
displayed as the vertical axis.
This changes to the 2-plane display mode configured of Y-X and Y-Z. C
YX/YZ The Y axis is displayed as the horizontal axis, and the X axis and Z axis are
displayed as the vertical axis.
This changes to the 3D display mode. C
XYZ
A cube is displayed on the lower right of the screen.
Operation method (Changing the display mode)
(1) Press the menu Display mode . The menus for the selectable display modes appear.
The input area appears.
(2) Select the mode to display and press the The display mode and drawing area appear as a
menu. 2-plane image.
(Example) XY/XZ
I - 79
2. Monitor Screens
2.5 Trace
Operation method (Changing the display axis name)
(1) Press the menu Display mode . The menus for the selectable display modes appear.
The input area appears.
(2) Set the axis name, and press the INPUT XYC appears as the axis name in the display mode.
key. The X axis, Y axis and C axis are the three axes for
drawing.
XYC INPUT
The display mode includes the 1-plane, 2-plane and 3D display modes. The display mode currently
selected is shown with an image. The selected axis names are displayed in the image.
Display example
<1-plane> (XY) <2-plane> (XY/XZ) <3D> (XYZ)
2.5.7 Changing the Display Angle

Set the graphics display angle for the 3D display mode.
Press the menu key or the cursor movement keys, and rotate the cube displayed at the upper right of the
screen. Set the angle by pressing the INPUT key.
(Note 1) When the display angle is changed, the graphics displayed up to that point are erased.
(Note 2) The set display angle is held even if the power is turned ON and OFF.
(Note 3) The display angle can be set independently for the trace function and program check function.
These settings are not sequenced.
Operation method
(1) Press the menu key Rotate . The rotation mode is activated, and the following menu
appears.
Up Down Left Right
(2) Use the Up , Down , Left , Right The cube displayed at the lower right of the screen
menu to adjust the display angle. rotates according to the key operations.
The cursor movement keys ( ↑ , ↓ , Z Z

← , → ) can also be used to rotate. X Y
Y X
(3) Press the INPUT key. The display angle is changed.

When display angle is changed, the graphic data
(Note 1) The set display angle is held even after the power is turned OFF and ON.
I - 80
2. Monitor Screens
2.5 Trace
2.5.8 Switching the Full-screen Display Mode
Press the All display menu key to display the trace window on the whole screen. (full-screen display
mode).
Press this menu again to return the normal display.
Switching the display mode
All display
menu : ON
All display
menu : OFF
Full-screen display mode

Normal display mode
(Note 1) The selected display mode is maintained even after rebooting the machine.
(Note 2) The full-screen display mode is applied to the trace function and program check (2D/3D solid)
function commonly.
(Note 3) The full-screen display mode is applied commonly to all part systems.
Displaying a program
When pressing the Program display menu key, the contents of the machining program currently being
checked is displayed on the drawing area.
When pressing the Program display again, the displayed program is erased.
Note that this menu can be used only when the full-screen display mode is selected.
(Note 2) The program display mode is applied to the trace function and program check (2D) function
commonly.
(Note 3) The Program display menu key cannot be selected while the normal display mode is selected.
Program display mode is valid only when the full-screen display mode is selected.
(Note 4) The program display mode is applied commonly to all part systems.
2.5.9 Precautions for Tracing

(1) When the command speed increases in the trace mode, the shape being drawn with graphics will become
distorted. Especially, correct graphic drawing is not possible during machine lock.
(2) If program check (2D) is executed during the trace mode, the trace mode will be canceled.
(3) If trace is executed during program check mode, the program check will be canceled.
Refer to section "4.3.11 Precautions for Program Check Function (2D)" for other precautions.
I - 81
2. Monitor Screens
2.6 Program Check (2D)
Program check (2D) is a function that draws the machining program movement path without executing
automatic operation. The machining program can be checked with graphic data drawn at a high speed.
Using All display menu, normal display and full-screen display modes can be switched.
The programs that can be checked are operation searched machining programs (MDI program for MDI
mode).
If no machining program has been operation searched, the program check window will not be opened.
Refer to "4.3 Program Check (2D)" for details.
(Note) The program check (2D) function is an additional specification. The graphic check option is required.
■ Normal display (full-screen display mode is OFF)

<Drawing area>
■ Full-screen display (full-screen display mode is ON)

<Drawing area >
I - 82
2. Monitor Screens
2.7 Program Check (3D) [700 series only]
Program check (3D) is a function that draws the workpiece shape and tool movement in the cutting process
of the machining program as a solid image without executing automatic operation. The machining program
can be checked with graphic data drawn at a high speed.
The operation searched machining program (MDI program for MDI mode) can be checked.
The Program Check window will not open if no machining program has been searched.
The workpiece shape and tool shape used with this function can be set on the Edit screen.
Refer to section "4.4 Program Check (3D)" for details.
(Note) The program check (3D) function is an additional specification. The graphic check and 3D solid
graphic check options are required.
■ Normal display (full-screen display mode is OFF)

<Drawing area>
■ Full-screen display (full-screen display mode is ON)

<Drawing area>
I - 83
2. Monitor Screens
2.8 Counter All-axis Display
A counter for all axes opens as a pop-up display.

The type of displayed counter can be selected with the menu.
I - 84
2. Monitor Screens
Menus
Menu Details Type

Relat This displays the currently executed position B
posn
This displays the G54 to G59 workpiece coordinate system modal No. B
Work
co posn and the workpiece coordinate position in that workpiece coordinate
system.
This displays the coordinate position of each axis in the basic machine B
Machine
posn coordinate system having a characteristic position, specified by the
machine, as a zero point.
This displays the remaining distance of the movement command B
Remain being executed during automatic start or automatic halt. (The
command remaining distance is the incremental distance from the current
position to the end point of that block.)
Next This displays the details of the command in the block executed after B
command the block currently being executed.
Manual This displays the amount moved with the manual mode while the B
int amt manual absolute switch was OFF.
This displays the value obtained by subtracting the tool compensation B
Program
posn amount compensated for that axis from the position actually being
executed for each axis.
Close
This displays the position of the tool end from the workpiece B
Tip wk
posn coordinate reference point in the selected workpiece coordinate
system.
Tip This displays the position of the tool end from the machine coordinate B
machine system reference point in the machine coordinate system.
This displays the amount moved in the selected axis direction using B
the manual pulse generator in the hypothetical machine coordinate
system.
Pulse
Basically this is updated only when manual ABS is OFF. If "#7905
NO_ABS" is set to "1", this will be updated regardless of the manual
ABS ON/OFF.
(Note 1) The type of counter displayed first when the pop-up display appears is the relative position. If the
5-axis related option is ON, the counter will be the "Tip wk posn".
The counter which appears next is the type selected previously.
(Note 2) The menus Tip wk posn, Tip machine and Tip axis movement appear when the 5-axis related
option is ON.
I - 85
2. Monitor Screens
2.9 Tool Compensation Amount
The tool compensation data can be set and displayed.

The tool compensation data screen configuration differs according to the tool compensation type.
The number of tool compensation sets to be set or shown differs according to the option.
Refer to section "3.2 Tool Compensation Amount" for details.
[Tool compensation type I (M system)] Parameter "#1037 cmdtyp" = 1
The combined amount of the shape compensation and wear compensation are set as the compensation
data, with no distinction between shape compensation memory and wear compensation memory. (The
tool compensation data is the shape compensation amount + wear compensation amount.)
The compensation data is used commonly for the tool length compensation, tool position offset, tool
radius compensation, and three-dimensional tool radius compensation.
[Tool compensation type II (M system)] Parameter "#1037 cmdtyp" = 2

The shape compensation amount and wear compensation amount are set separately. The shape
compensation amount is furthermore divided into length and radius dimensions.
Of the compensation data, the length dimension data is used for the tool length compensation and tool
position offset, and the radius dimension data is used for the tool radius compensation and
three-dimensional tool radius compensation.
I - 86
2. Monitor Screens
[Tool compensation type III (L system)] Parameter "#1037 cmdtyp" = 3

The wear data, tool length data and tool nose data are set separately. These are changed with the
sub-menu.
(a) Wear data

Set the tool nose wear amount for each tool used. When the tool compensation No. is designated by the
tool command (T command), compensation is carried out matching the tool length data and tool nose
data.
(b) Tool length data

Set the tool length in respect to the program basic position of each tool used.
When the tool compensation No. is designated by the tool command (T command), compensation is
carried out matching the wear data and the tool nose data.
I - 87
2. Monitor Screens
(c) Tool nose data

Set the tool nose radius value (tool nose R), wear radius value (R wear) and tool nose point (tool nose
point P) of the tool nose mounted on the tool for each tool used. When the tool offset No. is designated
by the tool command (T command), offset is carried out matching the tool length data and tool nose data.
! CAUTION
! If the tool offset amount or workpiece coordinate system offset amount is changed during
automatic operation (including during single block stop), the changes will be valid from the
command in the next block or after several subsequent blocks.
I - 88
2. Monitor Screens
2.10 Workpiece Coordinate System Compensation
2.10 Workpiece Coordinate System Compensation
The coordinate system offset controlled by the NC can be set and displayed.
48 or 96 sets of coordinate system offset sets can be added according to the option.
Refer to "3.6 Workpiece Coordinate System Offset" for details.
(Note) The G92/G52 coordinate system offset cannot be set.
! CAUTION
! If the tool offset amount or workpiece coordinate system offset amount is changed during automatic
operation (including during single block stop), the changes will be valid from the command in the
next block or after several subsequent blocks.
I - 89
2. Monitor Screens
2.11 Counter Set
2.11 Counter Set
An arbitrary value can be set in the relative position counter which opens as a pop-up window.
Menus

Close
I - 90
2. Monitor Screens
2.11 Counter Set
Operation method
(1) Press the main menu Counter set . The relative position counter opens as a pop-up
window.
The cursor appears at the 1st axis of the relative
position counter.
Instead of the operation above, the axis The relative position counter opens as a pop-up
name address key can be pressed to set window.
the counter. The cursor appears at the designated axis (Z axis).
(Example) Z
(2) Using the ↑ , ↓ , or keys, move the The cursor moves.

cursor to the axis to be set.
(Note) If two axes or more of the same name exist such as mixed synchronization control, the cursor
moves to the axis corresponding to the address key to the axis name input first.
(3) Input a numeric value. The set value "100.000" appears at the cursor
(Example) 100.000 INPUT position. The cursor moves to the next axis.
If the INPUT key is pressed without

inputting a value, zero (0) will be set.
(4) Repeat step (3) for each axis. The pop-up window closes when the counter has been
set for the last axis.
For axes that are not to be operated, press
the ↓ key and move the cursor.
I - 91
2. Monitor Screens
2.12 Origin Set, Origin Cancel
Origin set and origin cancel can be executed.
Menus

The origin is set. A
Origin
set When main menu G92 set is pressed, the menu Origin set is
highlighted and the origin set mode is activated.
Origin The origin is canceled. A
cancel The origin cancel mode is activated when this menu is pressed.
Close
Differences between origin set and origin cancel
Origin set Origin cancel

The coordinate system is shifted so the current The coordinate system is shifted so the zero
position becomes the designated position of the point of the workpiece coordinate system
workpiece coordinate system. matches the zero point of the basic machine
Function
This is equivalent to "G92 X0". (When X is the coordinate system.
target axis.) This is equivalent to "G92 G53 X0". (When X is
the target axis.)
Changes in the The relative position counter and workpiece The relative position counter matches the
counter value coordinate counters become "0". machine coordinate counter.
The G92 shift amount is updated. The G92 shift amount and the G52 shift amount
Offset for the G54 to G59 coordinate system becomes
"0".
I - 92
2. Monitor Screens
Operation method (Setting the origin)
(1) Press the main menu G92 set . The relative position counter opens as a pop-up
window.
The menu Origin set is highlighted.
position counter.
(2) Using the ↑ , ↓ , or keys, move the The cursor moves.

cursor to the axis to be set.
(Note) If two axes or more of the same name exist such as mixed synchronization control, the cursor
moves to the axis corresponding to the address key to the axis name input first.
(3) Input 0, and then press the INPUT key. "0.000" appears at the cursor position.
The cursor moves to the next axis.
If the INPUT key is pressed without
inputting a value, zero (0) will be set.
(Origin zero)
(4) Repeat step (3) for each axis. The pop-up window closes when the origin has been
set for the last axis.
(Note) An error will occur if a value other than 0 is set.
Operation method (Canceling the origin)
(1) Press the main menu G92 set , and then The relative position counter opens as a pop-up
press the menu Origin cancel . window.
The menu Origin cancel is highlighted.
position counter.
(2) Press the INPUT key. The same value as the machine position appears at
the cursor position.
The cursor moves to the next axis.
(3) Repeat step (2) for each axis. The pop-up window closes when the origin has been
canceled for the last axis.
I - 93
2. Monitor Screens
2.13 Manual Numerical Value Command
The spindle function (S), miscellaneous function (M), tool function (T) and 2nd miscellaneous function (B)
commands can be executed.
The manual numerical value command can be executed by inputting an address such as S, M, T or B, as
well.
Menus

Close
I - 94
2. Monitor Screens
Operation method (Executing T31 with a manual numerical value command)
(1) Press the main menu MST . The S, M, T, B display opens as a pop-up window.
S 100
M 50
T 4
B 1000
Using the ↑ and ↓ keys, move the The cursor moves.

cursor to the position to be set.
(2) The manual numerical value command The S, M, T, B display opens as a pop-up window.
can also be issued by using the address The cursor appears at T.
keys instead of the operation above.
(Example) T S 100
M 50
T 4
B 1000
(3) Input a value. The input value is set.

31 INPUT
(Note) The cursor moves to the first line when the part system is changed while displaying the manual
numeric command window.
Operation method (Canceling the manual numerical value command)
The manual numerical value command mode is canceled by carrying out one of the following operations
before pressing the INPUT key.
• Press the menu Close
• Press the key
• Change the screen
Setting/output range of manual numerical value command
For each S, M, T and G command, the data type to output to user PLC is designated by parameters
"#12006 Mbin M binary", "#12008 Sbin S binary", "#12010 Tbin T binary" and "#12012 Bbin B binary".
The output data type and the manual numerical value command setting/output range are shown below.
BCD No-signed binary Signed binary

S -
Output M
0 to 99999999 -99999999 to 99999999
range T 0 to 99999999
B
(Note 1) Even if the parameter (#12008 Sbin S binary) is set to "0" (BCD), the signed binary output is
applied to S. BCD output is not applied.
(Note 2) If a negative value is set when the data type is "BCD type" or "No-signed binary type", a value
converted into positive value is output to user PLC.
(Note 3) Add a "-" sign before the value to set a negative value. The display will be a positive value.
(Note 4) A value larger than "#3001 slimt1" to "#3004 slimt4" or "#3005 smax1" to "#3008 smax4"
cannot be output for S.
I - 95
2. Monitor Screens
2.14 Modal Display
2.14 Modal Display
The state of each modal during automatic operation is displayed.

The displayed details differ for the M system and L system.
<M system>
(1)
(3)
(2)
(4)
(6)
(5)
(7)
(8)
(9)
(10) (11)
Display items
This displays each modal state.
(1) G00…G94 Status of currently executed G command modal
:
G69…G42.1
(2) G50:P=0.000000 Scaling magnification
(3) G54.1:P0 Extended workpiece coordinate system
(4) G69:R=0.000 Coordinate rotation angle (Displays within a ±360° range)
(5) G05:P0 High-speed machining mode
Q1 High-speed high-accuracy control 1
Q2 Spline interpolation
P10000 High-speed high-accuracy control 2 (SSS control OFF)
P1 High-speed machining mode I
P2 High-speed machining mode II
P3 High-speed machining mode III
SSS SSS valid
(6) G40: Tool radius compensation modal
D0 Compensation No.
= 100.000000: Shape compensation amount in respect to tool radius
10.000000 Tool radius wear amount
(7) G49: Tool length compensation modal
Z Compensation axis name
H0 Compensation No.
= 0.000000: Compensation amount
0.000000 Tool length wear amount
(8) G07.1:OFF Cylindrical interpolation modal
(9) G08: High-accuracy control mode
P0 High-accuracy control mode OFF
P1 High-accuracy control mode ON
(10) FA F modal value of currently executed program command
FM Manual federate
(11) Program command modal value of each currently executed command
S1 to S4 S command
M1 to M4 M command
T T command
B 2nd miscellaneous function (B) command
I - 96
2. Monitor Screens
2.14 Modal Display
<L system>
(1)
(9)
(2)
(3) (10)
(4)
(5)
(11)
(6)
(12)
(7)
(8)
(13)
Display items
This displays each modal state.
(1) G01…G94 Status of currently executed G command modal
:
G69…G42.1
(2) G54.1:P10 Extended workpiece coordinate system
(3) TX : -12.345 The total value of the first axis' tool length and wear compensation amount for the tool
being used
(4) TZ : 12.345 The total value of the second axis' tool length and wear compensation amount for the
tool being used
(5) TY : 10.000 The total value of the additional axis' tool length and wear compensation amount for
the tool being used
(6) TG : 123 Tool length compensation No.
(7) TW : 123 Wear compensation No.
(8) V 12345678 Modal value for constant surface speed spindle rotation speed (V1 to V4)
(9) FA 24000.00 F modal value of currently executed program command
(10) FM 1200.00 Manual federate
(11) FS 0.0000 Program command synchronous feedrate modal value
(12) FE 0.0000 Thread lead command synchronous feedrate modal value
(13) Program command modal value of each currently executed command
S1 to S4 S command
M1 to M4 M command
T1 to T2 T command
B 2nd miscellaneous function (B) command
(Note) Fixed cycle programs

When a fixed cycle command is executed, the G command in the fixed cycle subprogram is not
affected by the G modal in the called program.
I - 97
2. Monitor Screens
2.14 Modal Display
Menus

Close
(Note) The menu is common for the M system and L system.
I - 98
2. Monitor Screens
2.15 Program Tree Display
2.15 Program Tree Display
This displays the main program, subprogram, MDI interrupt and user macro call nesting structure.
Display items

(1) 0 Program No. (0 to 15 characters)
If the program No. (program name) exceeds 15 characters, "*" will appear at the 15th
character.
(2) N Sequence No. (0 to 99999)
(3) B Block No. (0 to 99999)
(4) L Remaining number of subprogram repetitions (0 to 99)
(5) Mode Operation mode (0 to 7 characters)
(6) Main Main program
(7) 1 to 8 Called subprogram, user macro call and MDI interrupt
Menus

Close
I - 99
2. Monitor Screens
2.16 Intagrated Time Display
2.16 Integrated Time Display
The integrated time (date, time, power ON time, automatic operation time, automatic start time, external
integrated time 1, external integrated time 2, cycle time) controlled by the NC can be set and displayed.
Note that the cycle time cannot be set. (Cycle time is display only.)
The integrated times displayed in cycle time display area on "Auto/MDI" tag can be set.
Display items

(1) #1 Date The current date set in the NC is displayed.
Year: 4 digits, Month: 2 digit, Date: 2 digit (YYYY.MM.DD)
(2) 2 Time The current time set in the NC is displayed with the 24-hour system.
(HH:MM:SS)
(3) 3 Power ON This displays the total integrated time of the time from NC power ON to OFF.
(HHHH:MM:SS)
(4) 4 Auto oper This displays the total integrated time of the work time from automatic start button
pressing in the memory (tape) mode to M02/M30 or reset button pressing
(HHHH:MM:SS)
(5) 5 Auto strt This displays the total integrated time during automatic starting from automatic start
button pressing in the memory (tape) mode or MDI to feed hold stop, block stop, or
reset button pressing. (HHHH:MM:SS)
(6) 6 Ext time1 This content differs depending on machine tool builder specification. (HHHH:MM:SS)
(7) 7 Ext time2 This content differs depending on machine tool builder specification. (HHHH:MM:SS)
(8) 8 Cycle time This displays the time that automatic operation is started from when the automatic
start button is pressed in the memory (tape) mode or MDI to when feed hold stop or
block stop is applied or the reset button is pressed.
(Note) When the #3 Power ON to #8 Cycle time displays reach the maximum value (9999:59:59), the count
stops, and the maximum value remains displayed.
I - 100
2. Monitor Screens
Menus

Time This sets the integrated time. A 2.16.1 Setting the
setting Integrated Time
Time The time that is displayed in upper line on cycle time display C 2.16.2 Setting the Time
select1 area is selected. Display Selection
Time The time that is displayed in bottom line on cycle time display C
select2 area is selected.
This closes the pop-up window and quits this function C
Close
I - 101
2. Monitor Screens
2.16.1 Setting the Integrated Time
Operation method
(1) Press the menu Time setting . The time setting mode is entered.
The cursor appears at the "#1 Date" position in the
integrated time display.
(2) Input today's date. "2003.08.19" appears at "#1 Date", and the cursor
(Example) 2003/8/19 INPUT moves to "#2 Time".
(3) Set the data for each item, and press the When "#7 External integrated time 2" has been set,
INPUT key. the cursor disappears, and the time setting menu
highlight is turned OFF.
If the item does not need to be set, press
Note that #8 Cycle time cannot be set, so
the cursor will not move.
(Note 1) The data delimiters are as shown below.

Item Valid delimiters during setting Delimiters in display
#1 Date " . " or " / " "."
#2 Time to #7 Ext time2 " : " or " / " ":"
#8 Cycle time ":"
(Note 2) If the Time setting menu or key is pressed again during the time setting mode, the time
setting mode will be canceled.
Setting range
Display item Range

#1 Date 1980.1.1 to 2069.12.31
2 Time 00:00:00 to 23:59:59
3 Power ON
4 Auto oper
5 Auto strt 00:00:00 to 59999:59:59
6 Ext time 1
7 Ext time 2
I - 102
2. Monitor Screens
2.16.2 Setting the Time Display Selection
The displayed time is set on cycle time display area.
Operation method
(1) Press the menu "Time select1" The time selection mode is activated, and the following
menu appears.
Power Auto Auto Ext Ext Cycle
Date Time
ON oper strt time1 time2 time
(2) Press the time type for the mode to The automatic operation time is displayed in upper line
display. on cycle time display area. The menu display returns
(Example) "Auto oper" to integrated time sub-menu.
(3) Press the menu "Time select2" The time selection mode is activated, and the following
menu appears.
Power Auto Auto Ext Ext Cycle
Date Time
ON oper strt time1 time2 time
(4) Press the time type for the mode to The automatic operation time is displayed in bottom
display. line on cycle time display area. The menu display
(Example) "Power ON" returns to integrated time sub-menu.
(Note 1) The displayed time is held even after the power is turned OFF and ON.
I - 103
2. Monitor Screens
2.17 Common Variables
The details of the common variables can be set and displayed on this screen.
If there is a common variable command (Note) in the machining program, the variable value (variable name)
set when the block is executed is displayed.
The number of common variable sets differs according to the specifications.
(Note) The variable names can be set for common variables #500 to #519.
(1)
(2)
(3)
Display items

(1) Variable No. This is the common variable No. There are address #100 and address #500
variables.
The #100 variables appear at the head when the power is turned ON.
If "#1052 MemVal" is set to "1" (Designate No. of common variable for common part
system), "*" is attached to the part system common variable. (Note that if there is only
one part system, "*" will not appear.)
(2) Variable value The setting range is -999,999,999 to 999,999,999 or blank.
An exponential is displayed when a 7 digits are set in the integer section and 5 digits
or more as set in the decimal section.
(Example) 1234567 → 1.2346E+006, 0.00001 → 1.0000E-005
The minimum setting unit that can be set is 1.0000E-099 (99 digits below decimal
point).
(Note) When the setting is "blank", the setting will be handled as "0" in the
calculations. However, when the conditional expressions EQ or NE are used,
the blank will not be handled as "0".
(3) Variable name A variable name can be assigned for #500 to #519.
Up to seven alphanumeric characters, starting with an alphabet character, can be set
for the variable name.
I - 104
2. Monitor Screens
Menus

This executes an absolute input. C 2.17.1 Setting Common
=Input Variables
This executes an addition input. C
+Input
Variabl This designates the variable No. to be displayed at the head. A

No.
This returns the last rewritten data to its original value. C
This menu key is valid for "Data Input", "Paste" and "Undo"
Undo
operations. Note that return to the original value is not possible after
variable clear and comment clear operations.
This copies the variable value and variable name at the cursor A 2.17.2 Copying/Pasting
Copy position. Common Variables
This pastes the copied variable value and variable name. C
Paste
This clears the contents of the variable No. at the cursor position or A 2.17.3 Erasing Common
Variabl continuous variable Nos. Variables
clear (Note) The contents are not cleared to "0". The state with no data is
entered.
This clears the variable No. at the cursor position or the continuous A
Name
clear variable number's variable name (Variable name: variable No. 500 to
519).
Close
I - 105
2. Monitor Screens
2.17.1 Setting Common Variables
Operation method (Setting "135.000" in variable No. 102)
(1) Press the menu Variabl No . The menu is highlighted.
(2) Designate the variable No. The common variable for the set No. appears at the
102 INPUT head.
The cursor can be moved to 102 using the

↑ , ↓ , and keys.
(3) Input a value. The set value appears.

135 INPUT
The value can also be set by pressing the

menu =INPUT instead of the INPUT
key.
The value can also be input as an
exponential.
(1.35E2 INPUT or 1.35E2 =INPUT .)
Operation method (Adding "1.234" to variable No. 102)
(1) Select common variable 102 with the

same procedure as steps (1) and (2)
above.
(2) Input a value. The value obtained by adding the input value to the
1.234 +INPUT original value appears.
(Example) If the original value is 135.000, 136.234
appears. (135.000 + 1.234 = 136.234)
Operation method (Setting "COUNTER" as the variable name for variable No. 509)
(1) Select common variable 509 with the The cursor appears at the cursor 509 variable position.
same procedure as steps (1) and (2)
above.
(2) Press the key. The cursor moves to the 509 variable name.
(3) Input the variable name. "COUNTER" appears.

COUNTER INPUT
(Note) The variable name can be set only for variable Nos. 500 to 519.
I - 106
2. Monitor Screens
2.17.2 Copying/Pasting Common Variables
Operation method
(1) Select the variable to be copied. The cursor moves to the selected variable.
One of the following methods can be used

to select the variable.
• Using the cursor movement keys
↓ and ↑ , move the cursor to the
variable to be selected.
• Press Variabl No. and set the
variable No. in the input area, and press
the INPUT key.
(2) Press the menu Copy . One line of the copied variable is highlighted.
(3) Select the variable to be pasted, and press The copied variable is pasted, and the highlight returns
the menu Paste . to normal.
The copied variable is held until a variable is newly
copied.
I - 107
2. Monitor Screens
2.17.3 Erasing Common Variables
Operation method (Erasing the variable value for variable number 102 to 104)
(1) Press the menu Variabl clear . The menu is highlighted.
(2) Input the No. (range) of the variable to be A message confirming the erasing appears.
erased. The background color of the erase range (variable
102/104 INPUT value) changes to light blue.
To erase only one variable, input one

variable No.
(102 INPUT )
(3) Press the Y key. The selected variable is erased.
Operation method (Erasing the variable name for variable No. 509)
(1) Press the menu Comment clear . The menu is highlighted.
(2) Select the variable , and press the INPUT A message confirming the erasing appears.
key The background color of the erase range (variable
name) changes to light blue.
509 INPUT
(3) Press the Y key. The variable name for 509 only is erased.
The variable value is not erased.
Precautions regarding erasing the variable value and variable name
The variable at the cursor position will become the target of the erasing if the INPUT key is pressed without
designating a variable No.
I - 108
2. Monitor Screens
2.18 Local Variables
The details of the local variables are displayed

Local variables 1 to 33 are prepared for each user macro subprogram call level. Up to 33 local variable data
items are displayed on one level. A 5-level configuration from level 0 to level 4 is used in page order. If there
is a local variable command or an argument designation called by the user macro subprogram in the block,
and that block is executed first, the set variable value (variable name) will be displayed.
(1)
(2)
(3)
(4)
Display items

(1) Execution level This displays the nest level of the subprogram control called by the user macro.
0 : Not in user macro call state
1 : User macro call level 1
(2) Display level This displays the nest level of the local variable displayed in the area.
(3) Variable No. This displays the local variable No.
The alphabetic character before the local variable No. is the argument code. G, L, N,
O and P cannot be used as arguments, and thus not displayed.
There are 33 local variables (1 to 33) for each user macro subprogram call level.
(4) Variable value This displays the local variable value.
If the variable data is "blank", the display will be blank.
An exponential is displayed when a 7 digits are set in the integer section and 5 digits
or more as set in the decimal section.
(Example) 1234567 → 1.2346E+006, 0.00001 → 1.0000E-005
(Note) When the setting is "blank", the setting will be handled as "0" in the
calculations. However, when the conditional expressions EQ or NE are used,
the blank will not be handled as "0".
I - 109
2. Monitor Screens
Menus
Display This lowers the local variable display level one by one. If this menu is C 2.18.1 Displaying the
level- pressed when the display level is 0, the level changes to display level Arbitrary Local Variables
4.
This increases the local variable display level one by one. If this menu C
Display
level+ is pressed when the display level is 4, the level changes to display
level 0.
Close
Relation of user macro subprogram call execution level and display level
Main (level 0) O1 (level 1) O10 (level 2) O100 (level 3) O1000 (level 4)
#1=0.1
#2=0.2 : : :
#3=0.3 G65 P10A10.B20. G65 P100A100. G65 P1000A1000.
: C30.; B200.; B2000.; :
G65 P1A1.B2.C3.; : : :
: M02; M99; M99; M99;
M02;
Level 0 Level 1 Level 2 Level 3 Level 4

display display display display display
Local variable Local variable Local variable Local variable Local variable
1 0.1000 1 1.0000 1 10.0000 1 100.0000 1 1000.0000

2 0.2000 2 2.0000 2 20.0000 2 200.0000 2 2000.0000
3 0.3000 3 3.0000 3 30.0000 3 300.0000 3 3000.0000
: : : : :
33 33 33 33 33
Precautions
The local variables are not erased when reset or when the power is turned OFF. They are erased at macro
call.
I - 110
2. Monitor Screens
2.18.1 Displaying the Arbitrary Local Variables
Operation method (Displaying the next level)
When the current display level is 0

(1) Press the menu Display level + . The level 1 local variables appear from the head.
When the menu Display level + is pressed again, the display level changes in the order of 2 → 3 → 4
→ 0 → 1 → 2 → … and so forth.
Operation method (Displaying the previous level)
When the current display level is 2

(1) Press the menu Display level - . The level 1 local variables appear from the head.
When the menu Display level - is pressed again, the display level changes in the order of 0 → 4 → 3
→ 2 → 1 → 0 … and so forth.
Operation method (Changing the displayed variable No.)
The displayed local variable No. changes when the page changeover keys (previous page , next page
) are pressed.
Local variable display
#1
:
#12
#13
:
#24
#25
:
#33
I - 111
2. Monitor Screens
2.19 Buffer Correction
During automatic operation (Memory, HD, FD, DS, memory card) or MDI operation, a block stop can be
applied, and the next command can be corrected or changed.
When a program error occurs, the block in which the error occurred can be corrected without resetting the NC,
and operation can be continued.
In 70 series, only the memory and the memory card can be used for the input/output device.
Memory
HD
Memory
card Preread Execution
DS Machine
block block NC operation control
FD
MDI
Buffer correction
(1) The next command can be corrected in the following two cases.
• When single block stop is applied, and there is a command block to be corrected in the next
command.
• When there is an error (program error) in the next command and automatic operation is stopped.
(2) Not only the displayed buffer data but also the contents in the device are corrected with the buffer
corrections. (The corrected data is reflected.)
(3) Several blocks following the next command can be corrected simultaneously.
Menus

Close
I - 112
2. Monitor Screens
Operation method
During a single block stop or when a program error stop occurs, the buffer can be corrected with the following
operations, and operation can be continued.
The normally executed program appears in the buffer correction area.
N121 G28 X10.Y10.; ← Previous command

N122 T1212; ← Command in execution
N123 S1230 M3; ← Next command and
N124 G00 X68. Z201.; subsequent commands
N125 G01 X80. Z195. F50;
N126 Z150.;
N127 G02 X100. Z185. R20;
(1) Press the main menu Prg correct . The buffer correction mode is entered.
N121 G28 X10.Y10.;

N122 T1212;
N123 S1230 M3; ← Next
command
N124 G00 X68. Z201.; and
N125 G01 X80. Z195. F50; subsequent
N126 Z150.; commands
N127 G02 X100. Z185. R20;
The display changes so that the next command is at

the head of the area. The buffer correction area
becomes the valid area, and the keys can be input or
the cursor moved.
The cursor can be moved freely within the buffer
correction area using the cursor keys.
(2) Correct the program with the same

method as a normal program editing.
(3) Press the INPUT key. The buffer correction mode ends, and the corrected
data is written into program.
If a program error has occurred, the error display is
erased.
(4) Confirm that the corrected data is correct, The program execution resumes from the currently
and then restart. stopped position.
I - 113
2. Monitor Screens
Precautions
(1) Buffer correction mode will not be applied in the following cases.
(a) Machining program for buffer corrections is in edit lock or program display lock state.
(b) Data protection key 3 is enabled.
(c) Machining program for the device in write-protection state
(d) Machining program in read-only state
(2) Starting and ending buffer corrections

(a) If automatic operation is started or there is no next command data, the buffer correction mode is not
entered even if the menu key is pressed.
(b) To stop or to cancel the buffer corrections, press the menu Close again, or press the key.
(c) If another menu key, etc., is pressed before pressing the INPUT key, the corrected buffer
contents return to the original data.
(d) If changing to another screen or resetting the NC during buffer correction, the buffer correction is
canceled. In this case, the corrected contents are not saved, and the buffer correction mode ends.
(3) Display data during buffer correction

(a) The key operations used for corrections in the buffer correction mode are the same as the
operations when editing a program.
Up to 16 blocks can be displayed. Even when a block is displayed over several lines, all 16 blocks
can be displayed by scrolling the buffer correction area.
(b) Number of characters in one block is max. 256.
If exceeds 256 characters, the block will be split into two.
(c) Up to 4096 characters can be edited with buffer corrections.
(4) Operations during buffer correction

(a) If there is no ";" (EOB) at the data in the last block corrected when the INPUT key is pressed, it is
added automatically.
(b) When the buffer correction mode is entered, the last block displayed in the buffer correction area
may not fit in if the block is long, etc.
To correct this type of block, take care to the following points.
• If a ";" (EOB) is added to the end of the displayed data, the section following the incomplete
display becomes another block. If ";" (EOB) is not added, the following section stays the same,
and is handled as the continuation of the displayed section.
• If one block is deleted by pressing the C.B key, the block is deleted up to the section following
the incomplete display (up to the ";").
(c) Operation cannot be started during buffer correction. An alarm occurs.
(d) If NC is reset during buffer correction, buffer correction mode will be canceled, although buffer
correction window is left opened. At this time, editing operation is not possible. Close the correction
window.
(e) Buffer correction writing is not interrupted by NC reset.
(5) For multi-part system

(a) When a machining program under buffer correction is called by another part system, a file
input/output error occurs to the caller-side part system, and restart of the operation will be disabled.
(b) If the same program is executed in another part system after a buffer correction, there may be some
changes in paths, etc. So, please be careful.
(6) Previous command and command in execution

(a) When the buffer is corrected following the operation mode change at single block stop, nothing will
be displayed in previous command and command in execution.
(b) When there is no block after sub program call or user macro call, a program error occurs at the last
block of the destination program. If a buffer correction is made in this state, the destination program
will be displayed in the buffer correction window, but the actual correction result will be reflected on
the source program.
I - 114
2. Monitor Screens
2.20 PLC Switch Function
The various control signals for NC operation can be turned ON and OFF.
Refer to the instruction manual issued by the machine tool builder for details.
(1)
(2)
Display items

(1) Mark indicating switch ON This is displayed for switches that are turned ON
(2) Switch name The display contents differ depending on machine tool builder specification.
Menus

Setting Setting of the PLC switch is started. A 2.20.1 Turning PLC
valid Switches ON/OFF
This turns ON the switch currently indicated by the cursor. C
ON
This turns OFF the switch currently indicated by the cursor. C

OFF

Close
I - 115
2. Monitor Screens
2.20.1 Turning PLC Switches ON/OFF
Operation method (To turn switch "#6 Program restart" ON)
(1) Press the menu Setting valid . The menu Setting valid will be highlighted.
A message confirming the start of PLC switch setting
will appear.
(2) Press "Y" or INPUT The PLC switch setting mode will be entered.
The cursor will appear at the PLC switch No. position.
The menu keys ON and OFF will appear normally.
(3) Press the cursor keys ↑ and ↓ to The #6 number is highlighted.
move the cursor to "#6".
(4) Press the menu key ON . The "#6 Program restart" switch turns ON, and a *
mark appears.
To turn OFF, press the menu key OFF.
a * mark appears.
(Note 1) If the Setting valid menu or key is pressed again during the PLC switch setting mode, the
PLC switch setting mode will be canceled.
(Note 2) The PLC switch setting mode is canceled when the PLC switch's pop-up window is closed.
(Note 3) The cursor will not appear in modes other than the PLC switch setting mode.
I - 116
2. Monitor Screens
2.21 Verify Stop
2.21 Verify Stop
The machining program operation can be block stopped at a registered verify stop position. The registered
verify stop position can be canceled.
In 70 series, only the memory, the serial, and the memory card can be used for the input/output device.
(Note) Verify stop is an additional specification. The verify stop option is required.
[When verify stop is registered]
[When verify stop position is displayed]
(1)
(2)
(3)
I - 117
2. Monitor Screens
2.21 Verify Stop
Display items

(1) Verify stop device name This is the name of the device for which verify stop is to be executed.
(2) Verify stop position This is the position of the program where verify stop is to be executed.
This display is cleared when program stop is completed, or NC is reset or canceled.
If the program No. (program name) exceeds 24 characters, "*" will appear as the 24th
character.
(3) Display during verification This is displayed during verification.
Menus (When verify stop is registered)

This selects the device to be stopped for verification. C "Registering the verify
Memory If a device with a directory is selected, the root is selected first. stop"
(In 70 series, only "Memory", "Serial", and "Memory card" are
C
HD displayed.)
C
Serial
Memory C
card
C
DS
C
FD
Sort This changes the method of sorting the list. C 2.2.3 Changing the
Stop This opens the verify stop position display window as a pop-up C "Canceling the verify
posn window. stop"
This changes whether to show or hide the list comment field. B 2.2.2 Changing Whether
Comment
The file name field is increased when the comment field is hidden. to Show or Hide the
nondisp
Comment Field
Close
Menus (When verify stop position is displayed)

Stop This cancels the verify stop setting. Note that automatic operation is C "Canceling the verify
cancel not reset. stop"
This returns the list to the <When verify stop is registered>. C
Retn
I - 118
2. Monitor Screens
2.21 Verify Stop
Operation method (Registering the verify stop)
(1) Select the part system for executing verify The currently selected part system is displayed at the
stop with the $<->$ key. upper left of the screen.
(2) Press the main menu Verify stop . The verify stop submenu appears.
(3) Select the device. The device name and root directory (HD:/) selected in
(Example) HD the device name and directory display fields are
displayed.
(4) Using the ↑ , ↓ , → and ← The following is displayed.

keys, move the cursor to the directory
containing the file to be set.
If the list contents differ from the actual device or directory, press the menu List update .
(5) Press the INPUT key. The cursor moves within the directory.
(6) Input the program No., sequence No. and The verify stop position is displayed, and the program
block No. using / as a delimiter. No. ("MDI" for MDI mode), sequence No., block No.
(Example) 1001/1/2 INPUT and [Verifying] appear.
When carrying out verify stop of and MDI

program, set "0" as the program No.
If pointing the cursor to a file name, the file
name is echoed back to the input area.
(7) Start the automatic operation. When the verify stop is completed, a message
indicating the end appears.
The stop position displayed on the screen is cleared,
and the [Verifying] display is erased.
I - 119
2. Monitor Screens
2.21 Verify Stop
Operation method (Canceling the verify stop)
(1) Carry out the operations in "Operation The verify stop position appears.
method (Registering verify stop)".
If the verify stop position is not displayed,
press the menu Stop position .
(2) Press the menu Stop cancel . The stop position displayed on the screen is cleared,
and the [Verifying] display is erased.
(Note) Verify stop can also be canceled during operation.
Precautions
(1) When registering the stop position (O, N, B values), confirm that the block exists in the searched
program. Verify stop will not be executed if the corresponding block is not found at the registered stop
position.
(2) Always set one of the O, N or B numbers. If nothing is set, a setting error will occur.
(3) If the O No. is not set, the O No. used during operation search will be used.
(4) If the N and B numbers are not set, the block will be searched using the O No.
(5) If there are several sequences and blocks with the same number in one program, verify stop will be
executed after executing the first block that matches in the execution order.
(6) The settings are canceled when verify stop is executed.
(7) The settings are canceled when reset is executed.
(8) If only the program number is set, verify stop will take place at the head of the program only when there
is a program number at the first line.
(9) Verify stop / Verify stop cancel cannot be performed for blocks being executed or blocks already read
into the preread buffer.
(10) Verify stop is not performed in the tapping mode.
(11) Verify stop is possible in a subprogram, but is not possible in a machine tool builder macro program.
(12) If verify stop is set for a fixed cycle block, verify stop will be executed after the positioning block is
completed.
(13) Verify stop is possible even when editing is locked.
(14) Verify stop is executed after executing the block set for the verify stop position. If the verify stop position
is set in a program call (M98) block, verify stop will be executed before the subprogram is called.
(15) If the set block is set to be skipped, verify stop will not be executed.
(16) The verify stop position can be registered for each part system.
(17) The stop position cannot be registered during verification.
(18) Registration of verify stop position is not possible for a program with 33 or more file name characters.
(19) In the case where the device is HD, memory card, DS, or FD at the time of verify stop position
registration, inputting "0//" will be resulted in a setting error.
I - 120
2. Monitor Screens
2.22 Load Meter Display
The spindle load and Z axis load, etc., are displayed.
(1)
Display items

(1) Load meter 1 The spindle load and Z axis load, etc., are displayed in a bar graph.
Load meter 2 These displayed contents differ according to the machine tool builder.
Menus

Close
I - 121
2. Monitor Screens
2.23 Spindle, Standby Display
The current spindle tool No. and the standby tool No. are displayed.
(1)
(2)
(3)
Display items

(1) Spindle standby The display contents differ depending on machine tool builder specification.
(2) Tool No. This displays No. of tool that is attached to the spindle or standby position in the
magazine 1
(3) -D For D data function and purpose, refer to the instruction manual issued by the
Menus

Close
I - 122
2. Monitor Screens
2.24 Tool Center Coordinate Display
The tool center coordinates, handle interrupt amount (tool axis movement) and tool center point speed are
displayed during the tool center point control function, tool length compensation along tool axis function, and
tool handle feed & interrupt function (handle feed along the tool axis, tool handle interrupt, tool diameter
direction handle feed, nose center rotation handle feed).
This function is an additional specification. The 5-axis related options (tool center point control, tool length
compensation along the tool axis, tool handle feed & interrupt) are required.
(1) (4)
(5)
(2)
(3)
(6)
Display items

(1) Tip Mach posn This displays the position of the tool center from the machine coordinate system
reference point in the machine coordinate system.
(2) Tip G54 This displays the position of the tool center from the workpiece coordinate reference
point in the selected workpiece coordinate system.
(3) Pulse This displays the amount moved in the selected axis direction using the manual pulse
generator in the hypothetical machine coordinate system.
Basically this is updated only when manual ABS is OFF. If "#7905 NO_ABS" is set to
"1", this will be updated regardless of the manual ABS ON/OFF.
(4) Mach posn This displays the coordinate position of each axis in the basic machine coordinate
system having a characteristic position, specified by the machine, as a zero point.
(5) Wk. G54 This displays the selected workpiece coordinate system (G54 to G59)/external
workpiece coordinate system (G54.1 Pn) and the workpiece coordinate position in
that workpiece coordinate system.
(6) Movement speed of tool This displays the movement speed of tool center. By the parameter "#1125 real_f",
center actual feedrate and command speed can be switched.
I - 123
2. Monitor Screens
Menus

This changes the displayed axes each counter. The displayed axes C
are changed to axes 1 to 5, and axis 6 and over.
This menu cannot be selected when applying to the following
Next condition.
axis • When the number of enabled axes is 5 or less.
• Even if the number of enabled axes is 6 or over, the number of
displayed axes is 5 or less according to the parameter "#1069
no_dsp" setting.
Close
I - 124
2. Monitor Screens
2.25 All Spindles' Rotation Speed Display
The current spindle tool No. and the standby tool No. are displayed.
This function only displays the value. It is not possible to operate here.
(2)
(1)
Display items

(1) Spindles' command This displays the spindles' command rotation speed (S command value).
rotation speed
(2) Spindles' actual rotation This displays the spindles' actual rotation speed (r/min).
speed
Menus

Close
I - 125
3. Setup Screen
3. Setup Screen
The setup screen is used to make tool and workpiece related settings, set user parameters, edit the MDI, set
the counter, and perform manual numerical value commands.

The setup screen is configured as shown below.
(1)
(2)
(3)
Display items

(1) Counter display This displays the relative position and machine position counter.
Up to 5 axes can be simultaneously displayed.
The following status symbols display if each of the axes are in a set position or status.
#1 to 4 : Reference position 1 to 4
][ : Servo OFF status
MR : Mirror image
>< : Axis removed
It is possible to set whether to consider the tool length and diameter compensation
using parameter "#1287 ext23/bit4".
(2) M,S,T,B Command This displays all command values for M (support function command value), S (spindle
command rotation speed), T (tool command value) and B (2nd miscellaneous function
command value). The spindle command rotation speed displays only 1st spindle.
The presence (absence) of the 2nd miscellaneous function command value is
designated using parameter "#1170 M2name".
Refer to "3.11 Manual Numerical Value Commands" for details.
(3) Spindle/Wait display The current spindle tool number and standby tool number can be displayed according
to the PLC program specifications. (The numbers do not display in the screen if not
created with the PLC program.)
The contents of this display differ based on the machine tool builder specifications.
I - 126
3. Setup Screen
Menus

This sets the tool compensation amount. 3.2 Tool Compensation
There are three types of tool compensation, and the display differs for each amount
type.
The number of tool compensation combinations set/displayed differs depending
on the options.
This performs the tool measurement. 3.3 Tool Measurement
By manually moving the tool to the measurement point, the movement distance
from the basic point to the measurement point is measured, and this can be set
as the tool compensation amount.
This menu displays if the option is enabled.
This registers tools. 3.4 Tool Registration
A tool number is allocated to the tool to allow the NC to recognize the tool
attached to the machine. The tool number is registered based on the magazine
pot, spindle, and standby location to which the tool is attached.
This performs the tool life management. 3.5 Tool Life
The life management data containing information such as the tool usage status Management
is set and displayed.
Two management methods are used for tool life management.
This menu displays if the option is enabled.
This sets the workpiece coordinate system offset amount. 3.6 Workpiece
This sets and displays the coordinate system offset amount controlled by the Coordinate System
NC. Offset
This performs the workpiece measurement. 3.7 Workpiece
This menu displays if the option is enabled. Measurement
This sets the user parameters. 3.8 User Parameters

This screen is used to switch between, set, and display eleven different
parameter types.
This edits the MDI program. 3.9 MDI Program Editing
Press this menu to show the MDI program contents in a pop-up display.
This sets an arbitrary value for the relative position counter. 3.10 Counter Setting
This performs the manual numerical value commands. 3.11 Manual Numerical
Value Commands
This searches T code among the designated program (including the 3.12 T Code List
subprograms) and lists in order that it was found. This menu is displayed only
when the T code list option is valid.
This registers machining programs to the pallet of automatic pallet changer 3.13 Pallet Program
(hereinafter APC). This menu displays if the option is enabled. Registration
This menu is only for 700 series.
I - 127
3. Setup Screen
The tool compensation data can be set and displayed.

The tool compensation data screen configuration differs according to the tool compensation type.
The number of tool compensation sets to be set or shown differs according to the option.
Inputting an address key, such as MST, displays manual numerical value command window where manual
numerical value command is executed.
3.2.1 Tool Compensation Amount (M system)

[Tool compensation type I] : Parameter "#1037 cmdtyp" = 1
The combined amount of the shape compensation and wear compensation are set as the compensation
data, with no distinction between shape compensation memory and wear compensation memory. (The
tool compensation data is the shape compensation amount + wear compensation amount.)
The compensation data is used commonly for the tool length compensation, tool position offset, tool
radius compensation, and three-dimensional tool radius compensation.
(1)
I - 128
3. Setup Screen
[Tool compensation type II] : Parameter "#1037 cmdtyp" = 2

The shape compensation amount and wear compensation amount are set separately. The shape
compensation amount is furthermore divided into length and radius dimensions.
Of the compensation data, the length dimension data is used for the tool length compensation and tool
position offset, and the radius dimension data is used for the tool radius compensation and
three-dimensional tool radius compensation.
(1)
! CAUTION
If the tool compensation amount or workpiece coordinate system offset amount is changed during
I - 129
3. Setup Screen
Display items

(1) Display area Displays the tool compensation data. The displayed cursor can be moved and data
set.
Data that cannot be displayed in the display area can be displayed using the keys
below.
↑ , ↓ : Scroll one line at a time.
, : Change the display contents one page at a time.
Compensation number : This is the compensation data number.
Compensation data : The display items differ depending on the tool compensation
type.
Type I : Compensation data
Type II : Length dimension, length wear, radius dimension, radius wear
The standard settings and display ranges are as follows.
Setting/display
Type Settings Details
range
Type I Compensation This sets the shape and wear -999.999 to
data combined compensation amounts. 999.999
Type II Length This sets the tool length compensation Length/Radius
dimension amount. dimension:
Length wear This sets the tool length wear -999.999 to
compensation amount. 999.999
Radius This sets the tool radius compensation Length/Radius
dimension amount. wear:
Radius wear This sets the tool radius wear -99.999 to
compensation amount. 99.999
(Note 1) The display range is when the minimum command unit is 1µm ("#1003 iunit"
= B, "#1041 I_inch" = 0).
Furthermore, the display and setting ranges are as follows based on the "#1003 iunit"
and "#1041 I_inch" setting combination.
Setting/display range
#1003 #1041
iunit I_inch Type I
Type II Length wear Type II Length dimension
Radius wear Radius dimension
0 -99.999 to 99.999 -999.999 to 999.999
B
1 - 9.9999 to 9.9999 -99.9999 to 99.9999
0 -99.9999 to 99.9999 -999.9999 to 999.9999
C
1 - 9.99999 to 9.99999 -99.99999 to 99.99999
0 -99.99999 to 99.99999 -999.99999 to 999.99999
D
1 - 9.999999 to 9.999999 -99.999999 to 99.999999
0 -99.999999 to 99.999999 -999.999999 to 999.999999
E
1 - 9.9999999 to 9.9999999 -99.9999999 to 99.9999999
I - 130
3. Setup Screen
Menus

This executes an absolute input. C 3.2.1.1 Setting the Tool
= Input Compensation Data
This executes an addition input. C
+ Input
Set the compensation number and press INPUT to put that A 3.2.1.1 Setting the Tool
Offset Compensation Data
No. number to the top and display the tool compensation data.
The cursor moves to the contents of that first line.
Line This copies the contents of the tool compensation data in the selected C 3.2.1.3 Copying/Pasting
copy line (one line). the Tool Compensation
Data
The contents (one line) of the copied tool compensation data are C
written to the line where the cursor is.
If changes are made to the data in that line after Line copy is
Line
paste selected from the menu, the data prior to the changes is written when
pasting.
The data in the copied line can be pasted as many times as is
required until new data is copied.
This erases the compensation data in the selected line (multiple lines A 3.2.1.2 Erasing the Tool
can be erased). Compensation Data
Selection method: Select the first and the last compensation number
Line to be erased.
clear [Ex.] 1/E: Set all compensation data to "0".
If the INPUT key is pressed without selecting a line, the
compensation data in the line where the cursor is currently positioned
is erased.
This undoes the last changes to the tool compensation data. C
Undo (This menu is valid for the "Data Input", "Paste Line" and "Undo"
operations.)
I - 131
3. Setup Screen
3.2.1.1 Setting the Tool Compensation Data
Operation method (Setting "37.000" in the length wear data of compensation No. (102))
(1) Press the menu key Offset No.
(2) Designate the Compensation No. The set number appears at the top of the area, and the
102 INPUT cursor moves.
It is possible to use the ↑ , ↓ , and

keys as well to move the cursor to the
offset No.102.
(3) Use the key to move the cursor to

the length wear position.
(4) Input the length wear value. The set value displays.
37.000 INPUT
Settings can be made by pressing the
=INPUT key instead of the INPUT
key.
Tool offset data = INPUT setting example
Old New
Tool length Tool length = INPUT

compensation compensation
40.0 37.0
Tool radius Tool radius
5.0 5.0
Workpiece Workpiece
Table Table
I - 132
3. Setup Screen
Operation method ("-3.000" is calculated and set in the length wear data for compensation number
(102).)
(1) Use the same procedure as (1) above to

move the cursor to the compensation No.
102 length wear position.
(2) Enter a value. The input value is added to the original value and
-3.000 +INPUT displays.
[Ex.] 37.000 displays if the original value is 40.000.
(40.000 – 3.000 = 37.000)
Tool offset data + INPUT setting example
Old New
Tool length Tool length + INPUT

40.0 -3.0
Tool radius Tool radius
5.0 5.0
Workpiece Workpiece
Table Table
I - 133
3. Setup Screen
3.2.1.2 Erasing the Tool Compensation Data
Operation method (Erasing one line of tool compensation data at the cursor position)
(1) Move the cursor to the line to The cursor appears at the data item of the selected
be erased with the ↑ , ↓ , and compensation No.
keys.
(2) Press the Line clear and INPUT The menu keys are highlighted and a message
menu. displays confirming whether it is okay to erase.
The background color of the data to be erased
displays in light blue.
(3) Press the Y or INPUT key. The selected line of data (one line amount) is cleared
to zero.
To cancel the erasing, press a key other The data erased to zero displays at the top of the
than Y or INPUT . compensation data.
Operation method (Erasing the compensation data from compensation number 122 to 125.)
(1) Press the Line clear menu. The menu is highlighted.
(2) Input the compensation number of the A message box displays to confirm whether it is okay
data range to be erased. to erase the data.
122/125 INPUT The background color of the data to be erased
(3) Press the Y or INPUT key. The compensation data for the selected compensation
number is erased, and the menu highlight returns to
Press a key other than Y or INPUT normal.
in order not to erase the data. The data cleared to zero displays at the top of the
compensation data.
(Note) If the INPUT key is pressed without selecting an compensation number, the line where the cursor
is located is erased.
I - 134
3. Setup Screen
3.2.1.3 Copying/Pasting the Tool Compensation Data
Operation method (Copying/pasting one line of tool compensation data)
(1) Move the cursor to the line to be

copied with the ↑ , ↓ , and
keys
(2) Press the Line copy menu. The background color of the copied data changes to
light blue.
(3) Move the cursor to the line (compensation

No.: 109) where the data is to be pasted.
(4) Press the Line paste menu. The copied compensation data is written in the line
where the cursor is.
The background color returns to normal.
The copied compensation data is held until another
line is copied.
(Note 1) If the compensation data for the copied line is changed after the menu Line copy is pressed, the
data prior to the change is written when pasted.
I - 135
3. Setup Screen
3.2.2 Tool Compensation Amount (L system)

3.2.2.1 Wear Data
Set the tool nose wear amount for each tool used. When the tool compensation No. is designated by the
tool command (T command), compensation is carried out matching the tool length data and tool nose
data.
(1)
! CAUTION
I - 136
3. Setup Screen
Display items

set.
below.
Compensation data : This displays the tool nose wear compensation amount of
1st axis, 2nd axis and additional axis.
The standard settings and display ranges are -99.999 to 99.999.
= B, "#1041 I_inch" = 0).
(Note 2) Set whether to set the additional axis tool nose wear compensation amount
for 3rd or 4th axis at parameter "#1520 Tchg34".
(Note 3) Displays only for the number of valid axes if only 1st axis or 2nd axis are
valid.
(Note 4) Depending on the setting of parameter #8010(Max. value), the
setting/display range may be different from the above.
(Note 5) Depending on the setting of parameter #8011(Max. additional value), the
Furthermore, the display and setting ranges are as follows based on the "#1003 iunit"
and "#1041 I_inch" setting combination.
(Type I, Type II, Type III wear and tool length data)
#1003 #1041
iunit I_inch
0 -99.999 to 99.999
B
1 - 9.9999 to 9.9999
0 -99.9999 to 99.9999
C
1 - 9.99999 to 9.99999
0 -99.99999 to 99.99999
D
1 - 9.999999 to 9.999999
0 -99.999999 to 99.999999
E
1 - 9.9999999 to 9.9999999
X axis offset
X axis tool length offset +X axis wear offset
Z axis offset
Z axis tool length offset +Z axis wear offset
Tool nose
Y axis offset (additional axis)

X-axis tool nose
Y axis tool length offset +Y axis wear offset
wear offset amount
Z-axis tool nose wear offset amount
I - 137
3. Setup Screen
Menus

This executes an absolute input. C 3.2.2.4 Operation
= Input Method
(1) Setting the Tool
This executes an addition input. C Compensation Data
+ Input
Wear This changes to the wear data display. B

data (Note) This menu displays for Type III.
Length This changes to the tool length data display. B
Nose This changes to the tool nose data display. B
Set the compensation number and press INPUT to put that A 3.2.2.4 Operation
Offset number to the top and display the tool compensation data. Method
No. The cursor moves to the contents of that first line. (1) Setting the Tool
Compensation Data
Line This copies the contents of the tool compensation data in the selected C 3.2.2.4 Operation
copy line (one line). Method
(3) Copying/Pasting the
The contents (one line) of the copied tool compensation data are C Tool Compensation Data
written to the line where the cursor is.
If changes are made to the data in that line after Line copy is
Line
paste selected from the menu, the data prior to the changes is written when
pasting.
This erases the compensation data in the selected line (multiple lines A 3.2.2.4 Operation
can be erased). Method
Selection method: Select the first and the last compensation number (2) Erasing the Tool
Line to be erased. Compensation Data
clear [Ex.] 1/E: Set all compensation data to "0".
If the INPUT key is pressed without selecting a line, the
compensation data in the line where the cursor is currently positioned
is erased.
This undoes the last changes to the tool compensation data. C
Undo (This menu is valid for the "Data Input", "Paste Line" and "Undo"
operations.)
The wear data displays when the power is turned ON.

Following that, the wear data, tool length data, and tool nose data selection is stored.
I - 138
3. Setup Screen
3.2.2.2 Tool Length Data

Set the tool length in respect to the program basic position of each tool used.
When the tool compensation No. is designated by the tool command (T command), compensation is
carried out matching the wear data and the tool nose data.
(1)
! CAUTION
Display items

(continued on next page) set.
below.
Compensation data : This displays the tool length compensation amount of 1st
axis, 2nd axis and additional axis.
The standard settings and display ranges are -99.999 to 99.999.
= B, "#1041 I_inch" = 0).
(Note 2) Set whether to set the additional axis tool nose wear compensation amount
for 3rd or 4th axis at parameter "#1520 Tchg34".
(Note 3) Displays only for the number of valid axes if only 1st axis or 2nd axis are
valid.
I - 139
3. Setup Screen

Display area Furthermore, the display and setting ranges are as follows based on the "#1003 iunit"
(Continued from previous and "#1041 I_inch" setting combination.
page)
#1003 #1041
iunit I_inch
0 -999.999 to 999.999
B
1 -99.9999 to 99.9999
0 -999.9999 to 999.9999
C
1 -99.99999 to 99.99999
0 -999.99999 to 999.99999
D
1 -99.999999 to 99.999999
0 -999.999999 to 999.999999
E
1 -99.9999999 to 99.9999999
Generally, the center of the tool rest or the tip of the base tool is used as the programmed base position.
(1) The programmed base position is the center of the tool rest:
Basic position
(basic point)
X-axis tool length

offset amount
Z-axis tool length

offset amount
(2) The programmed base position is the tip of the base tool:
Basic tool
Tool used for

machining
Basic point
X-axis tool length

offset amount
Z-axis tool length offset amount
Menus
Same as "3.2.2.1 Wear Data".
I - 140
3. Setup Screen
3.2.2.3 Tool Nose Data

Set the tool nose radius value (tool nose R), wear radius value (R wear) and tool nose point (tool nose
point P) of the tool nose mounted on the tool for each tool used. When the tool compensation No. is
designated by the tool command (T command), compensation is carried out matching the tool length
data and tool nose data.
(1)
! CAUTION
I - 141
3. Setup Screen
Display items

(continued on next page) set.
below.
Compensation data : This displays the following items:
Tool nose R, R wear, tool nose point R
The standard settings and display ranges are as follows.
Setting/display
Settings Details
range
Tool nose R This sets the tool radius (nose R). -999.999 to
(Note 2) 999.999
R wear This sets the tool radius (nose R) wear -99.999 to
(Note 2) (Note 3) amount. 99.999
Tool nose point P This sets the tool nose point (number). 0 to 9
(Note 4)
= B, "#1041 I_inch" = 0).
(Note 2) Set at the radius value if parameter "#1019 dia” is "0", or at the diameter
value if this parameter value is "1".
(Note 3) Depending on the setting of parameter #8010(Max. value), the
(Note 4) An absolute setting is applied even if the tool nose point is entered by
pressing the + Input menu and entering a value.
I - 142
3. Setup Screen

Display area Furthermore, the display and setting ranges are as follows based on the "#1003 iunit"
(Continued from previous and "#1041 I_inch" setting combination.
page)
#1003 #1041 Setting/display range

iunit I_inch
Tool nose R R wear
0 -999.999 to 999.999 -99.999 to 99.999
B
1 - 99.9999 to 99.9999 - 9.9999 to 9.9999
0 -999.9999 to 999.9999 -99.9999 to 99.9999
C
1 - 99.99999 to 99.99999 - 9.99999 to 9.99999
0 -999.99999 to 999.99999 -99.99999 to 99.99999
D
1 - 99.999999 to 99.999999 - 9.999999 to 9.999999
0 -999.999999 to 999.999999 -99.999999 to 99.999999
E
1 - 99.9999999 to 99.9999999 - 9.9999999 to 9.9999999
2 6 1
7 0 5
X
R
Z 3 8 4
r
Tool nose point
Menus
Same as "3.2.2.1 Wear Data".
I - 143
3. Setup Screen
3.2.2.4 Operation Method
(1) Setting the Tool Compensation Data
Operation method (Setting "18.000" in the X-axis tool nose wear compensation amount of
compensation No. (1))
(1) Press the menu key Offset No.
(2) Designate the Compensation No. The set number appears at the top of the area, and the
1 INPUT cursor moves.
It is possible to use the ↑ , ↓ , and

keys as well to move the cursor to the
offset No.1.
(3) Use the key to move the cursor to

the length wear position.
(4) Input the X-axis tool nose wear The set value displays.
compensation amount.
18.000 INPUT
Settings can be made by pressing the
=INPUT key instead of the INPUT
key.
(Ex.) Tool compensation data =INPUT
X-axis tool nose

20.000 wear offset amount
= INPUT
18.000
Old New
I - 144
3. Setup Screen
Operation method ("-2.000" is calculated and set in the X-axis tool nose wear compensation amount
for compensation number (102).)
(1) Use the same procedure as (1) above to

move the cursor to the compensation No.
1 X-axis length wear position.
(2) Enter a value. The input value is added to the original value and
-2.000 +INPUT displays.
[Ex.] 18.000 displays if the original value is 20.000.
(20.000 – 2.000 = 18.000)
(Ex.) Tool compensation data +INPUT
X-axis tool nose

20.000 wear offset amount
+ INPUT
-2.000
Old New
I - 145
3. Setup Screen
(2) Erasing the Tool Compensation Data
Operation method (Erasing one line of tool compensation data at the cursor position)
(1) Move the cursor to the line to The cursor appears at the data item of the selected
be erased with the ↑ , ↓ , and compensation No.
keys.
(2) Press the Line clear and INPUT The menu keys are highlighted and a message
menu. displays confirming whether it is okay to erase.
The background color of the data to be erased
(3) Press the Y or INPUT key. The selected line of data (one line amount) is cleared
to zero.
To cancel the erasing, press a key other The data erased to zero displays at the top of the
than Y or INPUT . compensation data.
Operation method (Erasing the compensation data from compensation number 1 to 3.)
(2) Input the compensation number of the A message box displays to confirm whether it is okay
data range to be erased. to erase the data.
1/3 INPUT The background color of the data to be erased
(3) Press the Y or INPUT key. The compensation data for the selected compensation
number is erased, and the menu highlight returns to
in order not to erase the data. The data cleared to zero displays at the top of the
compensation data.
(Note) If the INPUT key is pressed without selecting an compensation number, the line where the cursor
is located is erased.
I - 146
3. Setup Screen
(3) Copying/Pasting the Tool Compensation Data
Operation method (Copying/pasting one line of tool compensation data)
(1) Move the cursor to the line to be

copied with the ↑ , ↓ , and
keys
(2) Press the Line copy menu. The background color of the copied data changes to
light blue.
(3) Move the cursor to the line (compensation

No.: 6) where the data is to be pasted.
(4) Press the Line paste menu. The copied compensation data is written in the line
where the cursor is.
The copied compensation data is held until another
line is copied.
(Note 1) If the compensation data for the copied line is changed after the menu Line copy is pressed, the
data prior to the change is written when pasted.
(Note 2) It is not possible to paste the data to a different display (wear data, tool length data, tool nose data).
I - 147
3. Setup Screen
3.3 Tool Measurement
3.3.1 Tool Measurement (M system)

By manually moving the tool to the measurement point, the movement distance from the basic point to the
measurement point is measured, and this can be set as the tool compensation amount.
There are two types of tool measurement: Tool length measurement I, Tool length measurement II
Tool length measurement I
When the tool is at the machine coordinate zero point, the distance from the tool tip to the measurement
point (workpiece upper end) is measured, and can be set as tool compensation data.
Machine coordinate zero point Start
Using a reference position return, etc., position

the tool at the basic point.
Select the measurement tool.
Turn ON the TLM switch of the machine

Movement amount operation board.
(Tool compensation data)
Using JOG feed, manual handle feed, etc.,
Workpiece move the tool to the measurement point.
Table
When the measurement is completed, designate
the tool compensation No.
Finish
I - 148
3. Setup Screen
Tool length measurement II

When the tool is at the machine coordinate zero point, the distance from the machine coordinate zero
point to the tool tip is measured, and can be set as tool compensation data.
Machine coordinate zero point Start
Confirm the value of the operation parameter

"tlml".
Tool compensation data
(operation parameter)
(internal computing)
When using the gauge block, etc., set the value
of the reference surface height.
Using a reference position return, etc., position

Movement amount the tool at the basic point.
Select the measurement tool.

tlml
Gauge block Reference surface

height Turn ON the TLM switch of the machine
Table operation board.
Using JOG feed, manual handle feed, etc.,

move the tool to the measurement point.
When the measurement is completed,

designate the tool compensation No.
Finish
(Note) Changing of the tool measurement type is determined based on the measurement axis (tool length
measurement axis, tool radius measurement axis) TLM reference length (parameter "#2016 tlml+") at
each measurement mode. When parameter "#2016 tlml+" is "0", the tool measurement type is tool
length measurement I.
I - 149
3. Setup Screen
Screen image
(1)
(2)
(4)
(3)
(5)
Display items

(1) Manual measurement This displays the manual measurement status.
status display Refer to the "Manual measurement status display" section for further details.
(2) Counter display TLM value : This displays the value during measurement.
This will be the same as the machine position until the sensor is contacted.
This will be the skip coordinate position after the sensor is contacted.
Measurement value :
For tool length measurement type I : TLM value − Reference surface height
For tool length measurement type II : TLM value − Reference surface height +
TLM reference length
For tool radius measurement, measurement result is displayed in absolute value.
(Note) The TLM value counter differs according to the parameter "#1328 TLM type"
value.
0 : The position when the measurement switch was turned ON is displayed
as 0.
1 : The display is based on the machine zero point.
L meas : Z (Axis name) The axis selected in the parameters "#8711 TLM L meas axis" and "#8712 TLM D
R meas : X (Axis name) meas axis" is the target axis for the measurement.
(3) Reference surface height This displays a value for the reference surface height.
The setting range is from -99999.999 to 99999.999(mm)
I - 150
3. Setup Screen

(4) Guide drawing This displays the measurement image. The contents of the guide drawing will differ
depending on the tool measurement type.
Tool length measurement I guide drawing Tool length measurement II guide drawing
(5) Tool compensation data This displays the tool compensation data. Depending on the tool compensation type
(I/II), the display details of the displayed tool compensation data will differ.
Menus

This writes the value displayed in "Mea value" as the tool C
Offset The wear amount is cleared to "0" for the tool compensation type II.
write
The tool compensation amount cannot be written in when the menu
Offset No. or Surface hight is highlighted.
When the compensation No. is set and the INPUT key is pressed, A 3.2.1 Setting the Tool
Offset the tool compensation data with that number at its head appears. Compensation Data
No. The cursor moves to the length dimension data of the top line of that
data.
This sets the reference surface height data. (The cursor moves to the A
Surface reference surface height.)
hight When the data is set in the input area and the INPUT key is
pressed, the reference surface height is set.
This changes the mode to the tool length measurement mode. B Carrying Out Tool
T-leng This mode is enabled when turning ON the power. Length Measurement
measure (The cursor moves to the length dimension position for tool
compensation type II.)
This changes the mode to the tool radius measurement mode. B Carrying Out Tool
(The tool measurement type is valid only for tool length measurement Radius Measurement
T-rad. II.)
measure
(The cursor moves to the radius dimension position for tool
compensation type II.)
I - 151
3. Setup Screen
Carrying out tool length measurement
(1) Turn ON the measurement switch. The message "On mea 0" appears.
Refer to the PLC Interface Manual for

details on measurement switch signals.
(2) Press the T-leng measure menu. The menu is highlighted, and the tool length
measurement starts. The measurement values are
displayed in "Meas value" during the measurement.
The menu T-leng measure is highlighted as a
default after the power is turned ON.
(3) Contact the measurement tool against the When the measurement tool contacts the sensor, the
sensor, using manual feed and manual skip position displayed in the measurement values
handle feed. Stop the feed when the tool counter.
contacts the sensor.
(4) The cursor moves to the compensation The cursor appears.

No. that sets the measurement results.
Offset No. 12 INPUT
The cursor display position differs
depending on the measurement mode.
Tool length measurement mode:
Length dimension
Tool radius measurement mode:
Radius dimension
(5) Press the Offset write menu. The measurement values are written as a tool
The wear amount is cleared to "0" for the tool
compensation type II.
(Note 1) The measurement values are not written if the cursor is in a position other than "Length" or
"Radius".
(Note 2) The axis returns and stops after contacting the sensor, but be careful not to move the axis after
that. If the axis moves after contacting the sensor, the distance that was actually moved will be
added to the measurement values counter, and the skip position will not be held.
(6) Turn OFF the measurement switch to The message "On mea 0" disappears.
finish measuring.
I - 152
3. Setup Screen
Manual measurement status display
The display will change as shown below during manual measurement.
Display Meaning
On mea 1 This state is entered if a skip signal is input during manual measurement.
The "On mea 2" state is shifted to after deceleration stop is confirmed.
On mea 2 This is the state during the first retract operation.
The "On mea 3" state is shifted to after retracting the retract amount.
On mea 3 This is the state in which retract by the retract amount has completed.
If the skip after deceleration stop confirmation signal is ON, the status display will remain
the same.
The "On mea 0" state is shifted to when this state is reset.
On mea 4 This is the state during the second measurement.
If the skip signal is not input even after moving to the specified position, a warning will
appear, and the status display will remain the same.
The "On mea 0" state is shifted to when this state is reset
On mea 5 This state is entered when the skip signal is input during the second measurement.
The "On mea 6" state is shifted to after deceleration stop is confirmed.
On mea 6 This is the state during the second return operation.
The "On mea 0" state is shifted to after retracting the retract amount.
On mea 0 This state is entered when not in the "On mea 1" to "On mea 6" states.
Carrying out tool radius measurement
The operating procedure of the tool radius measurement and submenu details are the same as when
measuring tool length.
(Use T-rad. measure instead of T-leng measure )
Refer to "Carrying out tool length measurement" for details.
I - 153
3. Setup Screen
3.3.2 Tool Measurement (L system)

This is used to carry out manual tool length measurement I or II. Either one is selected depending on the
setting of measurement switch and operation mode.
Manual tool length measurement I
This is the function to calculate the tool length compensation amount automatically by moving the tool to
the measurement point with manual feed. There are two types of measurement methods in manual tool
length measurement I: the basic point method and the measurement value input method. The method is
selected by setting parameter "#1102 tlm".
(1) Basic point method (#1102 tlm = 0)

Obtain the tool length with the tool nose placed on the measurement point.
To carry out the basic point method, a point to place the tool nose on (measurement point) is required.
Set the measurement point in parameter "#2015 tlml-" beforehand.
Z-axis + tlml
Measurement point
Tool length = Machine position – Measurement basic point (#2015 tlml-)

The expression above is used for automatic calculation in the basic point method.
Tool length
basic point
X-axis
tool length
Z-axis tool length

Tool nose
(Note) Always set the measurement point in radius value, regardless of the diameter/radius command.
I - 154
3. Setup Screen
(2) Measurement value input method (#1102 tlm = 1)

Actually cut the workpiece. Measure its dimensions, and obtain the tool length from the measured
values.
The measurement basic point is characteristic for each machine (the center of the chuck face, etc.)
To carry out the measurement value input method, a workpiece for measuring is required.
To measure the workpiece, set the basic point (measurement basic point) in parameter "#2015 tlml-"
beforehand.
Measurement
X-axis measurement value
basic point
X-axis + tlml
Measurement
basic point
Z-axis
Z-axis + tlml measurement value
Tool length = Machine position - Measurement basic point (#2015 tlml-) - Measurement value
The expression above is used for automatic calculation in the measurement value input method.
Tool length
basic point
X-axis
tool length
Z-axis tool length

Tool nose
(Note) Always set the measurement basic point in radius value, regardless of the diameter/radius
command.
I - 155
3. Setup Screen
Manual tool length measurement II

By using a device having a touch sensor, the tool compensation amount can be calculated just by
contacting the tool nose against the touch sensor with manual feed.
Set the measurement basic position (sensor position) with the parameter "#2015 tlml-" and "#2016 tlml+"
when using the main spindle side, "#2097 tlml-" and "#2098 tlml+" when using the sub spindle side.
X axis
Xm
Zp
Xp Zm
Z axis
Program basic position
X axis X axis tool compensation amount
X axis –
contact surface
Z axis +
contact surface Z axis tool compensation amount
Z axis - contact surface
X axis + contact surface

Z axis
When measured at the main spindle side:

Xm: - sensor machine coordinate position X axis (position measured by moving in - direction)
→ #2015 tlml- X axis
Zm: - sensor machine coordinate position Z axis (position measured by moving in - direction)
→ #2015 tlml- Z axis
Xp: + sensor machine coordinate position X axis (position measured by moving in + direction)
→ #2016 tlml+ X axis
Zp: + sensor machine coordinate position Z axis (position measured by moving in + direction)
→ #2016 tlml+ Z axis
When measured at the sub spindle side:

Xm: - sensor machine coordinate position X axis (position measured by moving in - direction)
→ #2097 tlml2- X axis
Zm: - sensor machine coordinate position Z axis (position measured by moving in - direction)
→ #2097 tlml2- Z axis
Xp: + sensor machine coordinate position X axis (position measured by moving in + direction)
→ #2098 tlml2+ X axis
Zp: + sensor machine coordinate position Z axis (position measured by moving in + direction)
→ #2098 tlml2+ Z axis
I - 156
3. Setup Screen
Tool compensation amount = Machine coordinate position (machine coordinate position at the time of skip
input) - Measurement basic position (sensor position)
The expression above is used for automatic calculation in Manual tool length measurement II.
Tool length basic point
X-axis tool
length
Z-axis tool length

Tool nose
When the tool touches the touch sensor while measurement switch is ON, the calculation result is set in the
tool data of the compensation No. specified with "Tool No. (Tool length measurement 2)" (PLC device), and
the wear data of the compensation No. set in "Wear compensation No. (Tool presetter)" (PLC device) is
cleared.
I - 157
3. Setup Screen
Screen image
[Manual tool length measurement I: Basic point method]
(4)
(1)
(5)
[Manual tool length measurement I: Measurement value input method]
(4)
(1)
(2) (5)
I - 158
3. Setup Screen
[Manual tool length measurement II]
(4)
(3)
(5)
Display items

(1) Measure value Measurement result and measurement axis are displayed. Displayed timing and
measurement result differ, depending on basic point method or measurement value
input method.
● Basic point method
Measurement result for the axis at the cursor position is displayed at all time.
Displayed data: Machine position - Measurement point (#2015 tlml-)
● Measurement value input method
Measurement result is displayed when the Meas memory menu is pressed.
Displayed data: Machine position - Measurement basic point (#2015 tlml-)
(Note) This is displayed only in "Manual tool length measurement I".
(2) Work meas Workpiece measurement result is set and displayed.
Setting is possible by pressing the Work measure menu or touching the value area of
the workpiece measurement value.
Setting range: -99999.999 to 99999.999(mm)
(Note) This is displayed only in "Manual tool length measurement I: Measurement
value input method".
(3) On mea "On mea" is displayed when the measurement switch is ON.
(Note) This is displayed only in "Manual tool length measurement II".
I - 159
3. Setup Screen

(4) Guide drawing This displays the measurement image. The contents of the guide drawing will differ
depending on the tool measurement type.
<Manual tool length measurement I: <Manual tool length measurement I:
Basic point method> Measurement value input method>
<Manual tool measurement II>
(5) Tool compensation data This displays the tool compensation data.
(Note 1) Cursor movement and part system changing operation are same as "Tool
compensation type III (L system)".
(Note 2) Automatically jumps to the compensation No. registered in "Tool No. (Tool
length measurement 2)" (PLC device) during manual tool length
measurement II. (Jumps even when the wear data is being displayed.) Note
that the ↑ , ↓ , , keys are disabled.
(Note) Measurement result and workpiece measurement value will be cleared when changing of part
systems, screens and measurement modes are carried out.
I - 160
3. Setup Screen
Menus

Depending on the mode, the following value is input as the tool C Carrying out tool
compensation amount at the cursor position, and the wear amount is measurement (Manual
cleared to "0". tool length measurement
● Manual tool length measurement I: Basic point method "Measure I: Basic point method)
value" value
● Manual tool length measurement I: Measurement value input Carrying out tool
method measurement (Manual
"Measure value" value - "Work meas" value tool length measurement
In "Manual tool length measurement I: Measurement value input I: Measurement value
Offset method", "Measure value" and "Work meas" will be cleared after input method)
write
compensation amount is written.
(Note 1) Tool compensation amount cannot be written in the following
cases:
● When the menu Offset No. and Work measure are
highlighted
● When the wear data is being displayed
● When the measurement result exceeds the setting range
(Note 2) If "Manual tool length measurement II", this is displayed in
gray and cannot be selected.
This sets the compensation No. and press the INPUT key. The tool A 3.2.1 Setting the Tool
Offset compensation data is displayed, placing the No. at the top. Compensation Data
No. (Note) If the measurement switch is turned ON, this is displayed in
gray and cannot be selected.
This sets the workpiece measurement value. If this menu is pressed, A Carrying out tool
the cursor moves to the workpiece measurement value. measurement (Manual
Point the cursor to the axis to be set, and set the data in the data tool length measurement
Work setting area. Press the INPUT key to set the workpiece I: Measurement value
measure measurement value. input method)
(Note) If not "Manual tool length measurement I: Measurement value
input method", this is displayed in gray and cannot be
selected.
Measurement result is calculated from the current machine position C Carrying out tool
and displayed. measurement (Manual
(Note) If not "Manual tool length measurement I: Measurement value tool length measurement
input method", this is displayed in gray and cannot be I: Basic point method)
Meas selected.
memory Carrying out tool
measurement (Manual
tool length measurement
I: Measurement value
input method)
Wear Wear data is displayed in tool compensation data. B
data
Length Tool length data is displayed in tool compensation data. This is the B
data default mode when the power is initially turned ON.
(Note) The data displayed on the tool compensation amount screen and the data displayed on "Tool
compensation data" in the tool measurement screen are not linked one another. (The wear data is not
necessarily displayed when the tool measurement screen has opened while the wear data is
displayed on the tool compensation amount screen.)
I - 161
3. Setup Screen
Carrying out tool length measurement (Manual tool length measurement I: Basic point method)
(Example) Carrying out tool measurement for compensation No.2, Z axis

(1) Select the tool to be measured with The tool to be measured is selected.
manual numerical value command. (Refer (Note) Select a tool without specifying compensation
to "3.11 Manual Numerical Value No. If compensation No. is specified,
Command" for details.) measurement result may not be obtained
correctly.
(2) Point the cursor to the position The cursor is displayed at compensation No.2, Z
(compensation No. 2, Z axis) where the axis.Calculation result of Z axis is displayed in
measurement result are to be set. "Measure value".
(Note) In order to measure a different axis, point the

cursor to the axis to be measured and perform
the following operations.
(3) Press the Offset write menu. The value displayed in "Measure value" is set in
compensation No.2, Z axis.
(Note 1) Compensation amount is written in diameter value for diameter command, in radius value for
radius command.
Carrying out tool measurement (Manual tool length measurement I: Measurement value input method)
(Example) Carrying out tool measurement for compensation No.3, X axis

manual numerical value command. (Refer (Note) Select a tool without specifying compensation
to "3.11 Manual Numerical Value No. If compensation No. is specified,
Command" for details.) measurement result may not be obtained
correctly
(2) Point the cursor to the position The cursor is displayed at compensation No.3, X axis.
(compensation No. 3, X axis) where the (Note) In order to measure a different axis, point the
measurement result are to be set. cursor to the axis to be measured and perform
the following operations.
(3) Cutting is executed in the longitudinal

direction.(For the Z axis, face turning is
executed.)
(4) The Meas memory menu is pressed Measurement result is displayed.

without retracting the tool at the end of
cutting operation.
I - 162
3. Setup Screen
(5) Retract the tool and measure the The Work measure menu is highlighted and the cursor
workpiece. And then press the moves to the workpiece measurement value.
Work measure menu.
(6) Set the workpiece measurement result. 10 is set for the workpiece measurement value.
10 INPUT Highlight of the Work measure menu is canceled and
the cursor moves to the tool compensation data.
(Note) Set a diameter value for diameter command

and a radius value for radius command.
(7) Press the Offset write menu. "Measurement result - workpiece measurement value"
is set to compensation No.3, X axis.
(Note 1) Compensation amount is written in diameter value for diameter command, in radius value for
radius command.
Carrying out tool measurement (Manual tool length measurement II)
manual numerical value command. (Refer
to "3.11 Manual Numerical Value
Command" for details.)
(2) Set the compensation No. of the The compensation No. of the compensation data to be
compensation data to be set in "Tool No. set is selected.
(Tool length measurement 2)" (PLC
device).
(3) Set the compensation No. of the wear data The compensation No. of the wear data to be cleared
to be cleared in "wear compensation No. is selected.
(tool presetter)" (PLC device).
(4) Turn the measurement switch ON. "On meas" is displayed. Guide drawing for manual tool
length measurement II is displayed. Tool
compensation data is displayed, placing the
compensation No. set in "Tool No. (Tool length
measurement 2)" (PLC device) at the top.
(Note) The row at the cursor position will not be

changed.
I - 163
3. Setup Screen
(5) Move the additional axis in the minus Measurement value is set for the additional axis of the
direction by manual feed and have the tool compensation No. set in "Tool No. (Tool length
nose contact with the touch sensor. measurement2)" (PLC device)
(6) Turn the measurement switch OFF. "On meas" disappears.
(Note 1) When entering the sensor area, the axis can be moved only in one direction selected from +X,
-X, +Z, -Z, (+Y、-Y). If two axes are moved simultaneously, measurement will not be carried out.
At this time, "E78 AX UNMATCH (TLM)" is displayed and the axis movement stops.
(Note 2) If the tool nose is contacting the sensor, the axis can be moved only in the direction moving
away from the sensor. Whether or not the tool nose is detached from the sensor can be judged
by the following conditions.
● The sensor signal has been turned OFF for 500ms or more.
● The tool nose is moved 100µm or more after the sensor signal has turned OFF.
The above conditions are set with parameter "#1227 aux11/bit2".
I - 164
3. Setup Screen
3.4 Tool Registration
A tool No. is assigned to each tool to make the tools installed on the machine recognizable to the NC. The
tool No. is registered corresponding to the magazine pot and spindle where that tool is installed, and the
standby location.
When the tool No. and magazine pot are changed by a tool selection command or tool replacement
command, the new tool No. is displayed
When not making an arbitrary setting for the number of registered tools, there are maximum 3 magazines,
and up to 120 tools can be registered for each magazines. When making an arbitrary setting, there are a
maximum of 5 magazines, and up to 360 tools can be registered for all magazines.
This function differs depending on the specifications of the machine tool builder. Refer to the instruction
manual issued by the machine tool builder for details.
(2)
(1)
(3)
Display items

(1) Magazine This displays the currently selected magazine No.
(2) Tool No.-D A maximum of 8 digits of data can be input for a tool No.
(Refer to the instruction manual issued by the machine tool builder for D functions
and purposes.)
When the "Tool No." column is blank, confirm the tool first, since the tool could not be
mounted, or the tool could not match the spindle.
Setting "0" erases the registered tool.
(3) Spindle/Wait This displays the magazine 1 spindle or standby tool No.
(used by PLC program) (The name of this area differs depending on the output from the PLC program.)
(Note) Displayed contents depend on the ATC parameter setting.
(4) PLC command This command is used to input data and perform sequence processing using the PLC
program.
I - 165
3. Setup Screen
Menus

Set the magazine pot number and press the INPUT key to position A 3.4.1 Registering a Tool
Pot in the Magazine Pot
No. that pot number at the top and display the tool number.
The cursor moves to the tool number for that pot number.
This sets or erases the tool No. of spindle and standby tools. A 3.4.3 Setting/Erasing the
Spindle
standby The cursor will move to the top tool No. of the spindle and standby Tool No. of
tools and the setting mode will be entered. Spindle/Standby Tools
This erases all the currently selected magazine tool data (tool number A 3.4.3 Setting/Erasing the
Magazn and D). Tool No. of
clear (Note 1) Unselected magazine tool data is not erased. Spindle/Standby Tools
(Note 2) The spindle and standby data cannot be erased.
Magazn This designates the magazine No. to be displayed on the screen. B 3.4.1 Registering a Tool
1 The displayed menu differs according to the machine specifications. in the Magazine Pot
: [Ex.] When there are two magazines, only the menu Magazine 1
: and Magazine 2 keys display.
Magazn
5
PLC The cursor moves to the PLC command setting area and the mode B 3.4.2 Setting the PLC
command changes to the setting mode. Command
I - 166
3. Setup Screen
3.4.1 Registering a Tool in the Magazine Pot
Operation method (Selecting a magazine No.)
(1) Press the menu Magazn 2 . The tool data of the set magazine No. appears.
(Note) The No. of magazines differs according to the machine specification.
Operation method (Registering the tool in the magazine pot)
(1) Designate the pot No. The tool data appears with the designated pot No. at
the head.
Pot No. 21 INPUT
The cursor moves to the tool No. setting column.
(2) Input the tool number. The input tool number displays and the cursor moves
50 INPUT to the next tool number.
When the INPUT key is pressed

without setting a value, the tool number
does not change and the cursor moves to
the "tool number" for the next pot number.
When the duplication check is valid, the operation

message "Exists in magazine 1. Set? (Y/N)" or "Exists
in spindle/standby. Set? (Y/N)", etc. appears if the
input tool No. already exists in valid magazine,
spindle/standby.
(Note 1) To set "D", use the →│ key to move the cursor.

Refer to the manual issued by the machine tool builder for details on the "D" functions and
purposes.
(Note 2) The duplication check is executed for only the tool No. The check does not depend on the
setting of "D".
(Note 3) If parameter "#8922 T-reg-no dup check" is set to "1", the operation message will not appear
even when the tool No. duplicates.
I - 167
3. Setup Screen
3.4.2 Setting the PLC Command
Operation method (Setting the PLC command)
(1) Set the value after the PLC command The set value displays in the PLC command setting
menu. field, and the PLC command setting mode is enabled.
The function of the command depends on the machine
PLC command 12 INPUT
tool builder’s specifications.
(Note) Select the PLC Command menu again before pressing the INPUT key, then the menu
highlight returns to normal, and the PLC command setting mode becomes disable.
(2) Press the menu PLC command , or the The PLC command setting mode is released, and the
menu highlight returns to normal.
key again to finish setting.
3.4.3 Setting/Erasing the Tool No. of Spindle/Standby Tools
Operation method (Setting the tool No. of spindle/standby tools)
(1) Press the Spindle standby menu. The cursor appears at the top tool No. of
spindle/standby.
In addition, the first "D" column is highlighted.
(2) Move the cursor to the data to be set using

the ↑ and ↓ keys.
(3) Input a new tool No. The tool No. changes. The cursor moves to the next
50 INPUT (Note1) tool No.
(4) Press the Spindle standby menu again The spindle/standby setting mode is cancelled.
or key to quit the spindle/standby
setting mode.
(Note 1) When the Spindle standby menu again or key is pressed before pressing the INPUT
key, the spindle/standby setting mode will be cancelled and the set data will be ignored.
(Note 2) Move the cursor with → key to set the "D" data.
Operation method (Erasing the tool No. of spindle/standby tools)
(1) Press the Spindle standby menu. The cursor appears at the top tool No. of
spindle/standby.
In addition, the first "D" column is highlighted.
(2) Move the cursor to the tool No. to be The tool No. of spindle/standby changes to “0”.
erased and input “0”.
0 INPUT
(Note 1) Move the cursor with → key and set “0” to erase the "D" data as the same manner as the tool
No.
I - 168
3. Setup Screen
3.4.4 Erasing the Tool Registration Data
Operation method (Selecting a magazine number and erasing the tool registration data.)
(1) Press the menu Magazn 2 . The tool registration data of the selected magazine No.
appears.
(2) Press the menu Magazn clear . A message displays confirming whether it is okay to
erase.
(3) Press the Y or INPUT key. All selected magazine tool data (tool number and D) is
erased.
Spindle/standby tool data is not erased.
I - 169
3. Setup Screen
3.5 Tool Life Management
The life management data of the tool usage conditions, etc., is set and displayed.
The tool life management specifications differ for the M and L system.
<M system>
Tool life management I
The usage time or No. of uses of the tool commanded in the program is incremented, and the usage
state of that tool is monitored.
Tool life management II

This method is the same as tool life management I, but with a spare tool selection function added.
A spare tool is selected from the group of tool commands commanded in the program. Tool
compensation (tool length compensation and tool radius compensation) is carried out for the selected
tool.
The tool life management related parameters (basic common parameters) include the following.
# Item Setting Details

1103 T_Life 0 This ignores the tool life management data.
T-life manage valid 1 This controls the tool life management.
1104 T_Com2 0 This treats the program tool command as a group No.
Tool com 2 Search for the group No. that matches with the tool No. in
(When tool life the tool registration data, and select the spare tool from
management is valid.) there.
1 This treats the program tool command as a tool No.
1105 T_sel2 0 This selects the tool from the tools in use in the same
Tool com 2 group, following the registration No. order.
(When tool life If there are no "Tools in use", the tools are selected in order
management is valid.) of "Tools not in use", "Normal life tools" and "Abnormal
tools", following the registration No. order.
1 This selects the tool with the maximum remaining life from
the tools in use and not in use in the same group.
When several tools have the same remaining life, the tools
are selected in order of registration No. If there are no
"Tools in use" or "Tools not in use", the tools are selected in
order of "Tools not in use", "Normal life tools" and
"Abnormal tools", following the registration No. order.
I - 170
3. Setup Screen
<L system>
Tool life management I ............ Tool life data display
The tool usage time and usage count indicated in the program is accumulated, and the usage status for
that tool is monitored. Tool life management can be performed for a maximum of 80 tools (tool Nos. 1 to
80).
(a) Time based control
The cutting time (G01, G02, G33 etc.) after performing the tool selection command (T) is calculated
in the tool usage time corresponding to the designated tool.
A warning is issued if the usage time at the time the tool selection command is performed reaches
the life time.
(b) Usage count based control
The tool usage count corresponding to the designated tool No. increases each time the tool
selection command (T) is performed.
A warning is issued if the usage count at the time the tool selection command is performed exceeds
the life time.
Tool life management II ........... Tool life data display / registration group list display
The life (usage time, usage count) of each tool is controlled, and if the life is reached, the same spare
tools are selected and used one by one from the group to which that tool belongs.
{ Group count : Multi-part system spec. : max. 40 groups for each part system
Single part system spec.: max. 80 groups
{ No. of tools in group : Max. 16
The tool life management related parameters (basic shared parameters) are shown below.
# Name Setting Details

1096 T_Ltyp 1 Tool life management I
(For L system only) 2 Tool life management II
Tool life management
type
1103 T_Life 0 The tool life management is not performed.
Enable tool life 1 The tool life management is performed.
management
1107 Tllfsc Set the no. of groups displayed at the tool life management II (L
(For L system only) series) screen.
Tool life management 0 Displayed no. of groups: 1, Max. No. of registered tools: 16
Display screen division
1 Displayed no. of groups: 2, Max. No. of registered tools: 8
2 Displayed no. of groups: 4, Max. No of registered tools: 4
The tool life management screen is made up of the group list display screen and the life management
data screen.
(There is no group list display screen in L system tool life management 1. Only the life management data
screen exists.)
Refer to the following sections for details of the display contents, menus, and an explanation of the
operations for each screen.
"3.5.1 Displaying the Group List"

"3.5.2 Displaying the Life Management Data in Group Units (M system)"
"3.5.3 Displaying the Life Management Data (L system: Tool life management I)"
"3.5.4 Displaying the Tool Life Management Data in Group Units (L system: Tool life management
II)"
I - 171
3. Setup Screen
3.5.1 Displaying the Group List

Tool life management data groups can be registered and erased.
<M system>
When changing from a group unit display to the group list display, the cursor displays at the group No. at
the group unit display.
(1)
Display items (M system)

(1) Regist group list The group Nos. registered as the tool life management data are listed in ascending
order.
Group Nos. can be set from 1 to 99999999, and maximum 1000 groups (Note) can be
set.
Maximum 60 groups can be displayed at a time. Use the / keys to change
the display if the No. of registered groups exceeds 60.
An asterisk will be added to the No. of the group in which all tools have reached their
lives.
(Note) The maximum number of the registered groups depends on the option.
I - 172
3. Setup Screen
<L system>
This screen is enabled only for tool life management type II (parameter "#1096 T_Ltyp" = 2).
The tool life management data currently being used and the group list display.
(1)
(10)
(3) (9)
(4) (8)
(7)
(5)
(6)
(2)
Display items (L system)

(1) Chosen Tool The life management information of the tool currently being used appears here.
(2) Regist group list The group Nos. registered as the tool life management data are displayed in a list.
Group Nos. can be set from 1 to 9999, and maximum 80 groups can be set.
An asterisk will be added to the No. of the group in which all tools have reached their
lives.
(Note) The maximum number of the registered groups depends on the option.
[CHOSEN TOOL]
Display item Details Display range
(3) Group Displays the life management group No. currently being used. 1 to 9999
(4) Tool No. Displays the tool No. currently being used. 1 to 999999
(5) Comp No. Displays the compensation No. currently being used. 1 to 80
(6) Mthd Displays whether the group currently being used is controlled by 0: Time
the usage time or usage count. 1: Count
(7) Used Displays the usage data for the tool currently being used. Usage time:
0 to 99999999 (s)
Usage count:
0 to 999999 (set)
(8) Total Displays the total usage data for the tool currently being used. Usage time:
In the case of tools using multiple compensation Nos., the total 0 to 99999999 (s)
usage data for all compensation Nos. displays. In the case of only Usage count:
one compensation No., the same value as "Used" displays. 0 to 999999 (set)
(9) Life Displays the life value for the tool currently being used. Usage time:
0 to 99999999 (s)
Usage count:
0 to 999999 (set)
(10) ST Displays the status of the tool currently being used. 0: Unused tool
1: Used tool
2: Normal life tool
3: Skipped tool
I - 173
3. Setup Screen
Menus (M system/L system)

Group Creates a new group and adds the group No. to the list. A "Registering a group"
regist
This erases all of the tool life management data included in the A "Erasing a group"
Group designated group No.
delete If the group No. is not designated, the tool life management data for
the group No. indicated by the cursor will be erased.
Grp all This erases all groups and their tool life management data registered A "Erasing all groups"
delete in the part system which is currently selected.
Changes the group No.. A "Changes the group
Group Specify a new group No. and press the INPUT key to change the No."
change group No. and then change the contents of the list.
An error occurs if an existing group No. is specified.
The tool life data for the group No. indicated by the cursor will be C "Changing to the group
T-life displayed. unit display"
group This changes to the mode enabling tool life management data to be
set and displayed with group unit Nos.
Operation method (Registering a group) (M system/L system)
(1) Press the menu Group regist .
(2) Designate the group No. to be registered. The life management data for the selected group No.
25 INPUT displays empty.
The group No., method, and life value is

set at the L system.
(Example) 25/1/3000 INPUT
(Note 1) An error occurs if the group No. duplicates a pre-existing group No.
(Note 2) The group is not registered if the following operations are performed after newly registering a
group No..
• The application is exited without registering even 1 item of tool life data.
• The screen is changed to that of other than the group unit display.
• The part system is changed.
Operation method (Erasing a group) (M system/L system)
(1) Press the menu Group delete .
(2) Designate the group to be erased. The selected group No. is erased.
72 INPUT
If nothing is input in the input area, the group at the cursor location is erased.
I - 174
3. Setup Screen
Operation method (Erasing all groups) (M system/L system)
(1) Press the menu Grp all delete . The confirmation message appears.
(2) Designate the group to be erased. All the registered groups and their tool life
72 INPUT management data is erased.
(Note 1) If no group has been registered, the operation message "Can't delete all groups" will appears.
Operation method (Changing the group No.) (M system/L system)
(Ex.) Changing the group No. from 5 to 20

(1) Use the ↑ , ↓ , and keys to
move the cursor to group No. 5.
(2) Press the menu Group change key. The menu is highlighted.
(3) Set the new group No.. The group No. changes to "20".
20 INPUT
Operation method (Changing to the group unit display) (M system/L system)
(Ex.) Displaying the group No. 5 tool life data.
(1) Use the ↑ , ↓ , and keys to

move the cursor to group No. 5.
(2) Press the menu T-life group or The screen changes to the group unit display and the
INPUT keys. group No. "5" tool life management data displays.
<M sysem>
<L system>
I - 175
3. Setup Screen
3.5.2 Displaying the Life Management Data in Group Units (M system)

The tool life management data of an arbitrary group is set and displayed. If the registered tools cannot be
displayed on one screen, scroll the screen using the or key.
(6)
(1) (7)
(2)
(3)
(4)
(5)
(8)
(9)
(10)
I - 176
3. Setup Screen
Display items (M system)

(1) Group No. This is the group No. of the tool for which tool life management is 1 to 99999999
performed.
Tools with the same group No. are regarded as spare tools.
(2) # This is the data setting No.. This is not the magazine pot No.
(3) Tool No. This is the No. corresponding to the each individual tool. 1 to 99999999
Maximum 1000 tools can be registered.
This is a fixed tool No. actually output for the tool command and
so on.
(4) ST
Tool status
Machine manufacturer release
Tool status
0 : Unused tool
Normally set to "0" when the tool is replaced with a new
tool.
1 : Used tool
This becomes "1" when the cutting actually starts.
2 : Normal life tool
This becomes "2" when the usage data (usage time and
No. of uses) exceeds the life data.
3 : Tool abnormality 1 tool
4 : Tool abnormality 2 tool
(Note) Item 3 and 4 differ depending on the machine tool builder
specifications.
I - 177
3. Setup Screen
(M system)
(5) Mthd
(a) Tool life management method

(b) Tool radius compensation data format
(c) Tool length compensation data format
(a) Tool life management method
0 : Usage time
This manages by the cutting execution time.
1 : No. of mounting times
This manages by the No. of times the tool became the
spindle tool in tool replacement, etc.
However, in the case where the cutting feed command
(G01, G02, G03 etc.) is not executed even once after
becoming the spindle tool, the No. of times is not counted.
2 : Usage count
This is counted when the rapid traverse command (G00
etc.) is changed to the cutting feed command (G01, G02,
G03 etc.). However, this is invalid in the case of a rapid
traverse or cutting feed command with no movement.
G00 G01 G00 G04 G01 G04 G01 G00
+1 During cutting feed +1
(b) Tool radius compensation data format

(c) Tool length compensation data format
0 : Compensation No.
The tool life management data compensation data is
handled as a compensation No., this No. replaces the
compensation No. designated in the process program, and
compensation is performed.
1 : Added compensation amount
handled as the added compensation amount, an addition is
made to the compensation amount shown with the
2 : Direct compensation amount
handled as the direct compensation amount, this No.
replaces the compensation amount shown for the
(6) L compen This depends on the data format designated in "Mthd". Compensation
No. : 1 to 400
Added compen-
sation amount
(7) R compen Direct Compen-
sation amount
(Note 1)
(8) Auxil This depends on the machine tool builder specifications. 0 to 65535
(9) Life Set the usage time (minutes), attachment count (No. of times Usage time:
attached to the spindle), or usage count (No. of holes drilled) for 0 to 4000 (min)
the life for each tool based on the data format set for "Method". No. of mounting
The life is infinite when "0" is set. times:
0 to 65000 (set)
No. of uses:
0 to 65000 (set)
I - 178
3. Setup Screen
(M system)
(10) Used This displays the usage data for individual tools based on the Usage time:
method specified for the tool life management method. 0 to 4000 (min)
(Note) This data is not counted during machine lock, auxiliary No. of mounting
function lock, dry run or for a single block. times:
0 to 65000 (set)
No. of uses:
0 to 65000 (set)
(Note 1) The "Length compensation" and "Radius compensation" calculation/direct compensation amount
setting/display range are as follows based on a combination of settings of "#1003 inunit (input unit)"
and "#1041 I_inch (initial inch)".
#1003 iunit #1041 I_inch Setting/display range

0 -999.999 to 999.999
B
1 -99.9999 to 99.9999
0 -999.9999 to 999.9999
C
1 -99.99999 to 99.99999
0 -999.99999 to 999.99999
D
1 -99.999999 to 99.999999
0 -999.999999 to 999.999999
E
1 -99.9999999 to 99.9999999
I - 179
3. Setup Screen
Menus (M system)

This displays the data of a group when that group No. of tool life A "Designating a group
Group No."
No. management data is set and the INPUT key is pressed. The group
No. can be referred to in the group list.
Line Copies one line of tool life management data where the cursor is C "Copying/pasting the
copy located. tool life data"
The copied tool life management data is written to the data in the line C
where the cursor is located.
Line If the copied data is changed after the menu Line copy
paste is pressed, the data before changing is written when pasted.
This erases a designated line (multiple lines possible) of tool life A "Erasing one line of tool
management data. life management data"
Line The first and the last line No. of the data to be erased is specified with "Designating and
clear a "/" separating the Nos. erasing a line"
If the INPUT key is pressed without specifying a line, the data in
the line where the cursor is located is erased.
This changes a group No. A "Changing a group No."
Group If a new group No. is set and the INPUT key pressed, the group
change No. changes.
An error occurs if a pre-existing group No. is set.
This scrolls the display of the tool life management data to the left and C
right.
Horiz
scroll The items below display alternately each time the menu is pressed.
1. Tool No., ST, Mthd, L compen, R compen
2. Tool No., Auxil, Life, Used
Prev Displays the previous group No. data. C
group
Next Displays the next group No. data. C

group
Group This displays the list of tool life data groups. C
list
Group This creates a new group. A "Registering a group"
regist
Group This erases all tool life management data contained in the currently A "Erasing a group"
delete displayed group No.
I - 180
3. Setup Screen
Operation method (Designating a group No.) (M system)
(1) Press the Group No menu. The menu is highlighted.
(2) Designate the group No. to be displayed. The tool life data of the designated group No. appears,
12 INPUT and the cursor moves to the head of the data.
(Note) If a group No. that does not exist is designated, a message appears to confirm the creation of a
new No. A new group is created if Y or INPUT is pressed.
Operation method (Changing a group No.) (M system)
(1) Press the Grp No. change menu. The menu is highlighted.
(2) Designate the group No. after changing. The group No. changes to "112".
112 INPUT
(Note) An error occurs if the group No. duplicates a pre-existing group No.
Operation method (Setting the tool life data) (M system)
(1) Move the cursor to the data to be set using The menu is highlighted.
the , ↑ , ↓ , and
keys.
It is possible to move to the line after the
registered line.
Set a tool No. for this line to newly register
tool life management data.
(2) Set a value. The set value displays.

20 INPUT The cursor moves one position to the right.
(Note 1) The other settings will be invalid when the tool ST (status) setting data are not set.
(Note 2) The same tool cannot be registered in more than one group.
(Note 3) If the tool No. is not set, the other data cannot be set.
(Note 4) Change the "Method" to initialize the related items.
Change the tool life management method (the 1st digit) to clear the "Life" and "Usage", and also
change the units.
Change the tool radius compensation data (the 2nd digit) to clear the "Radius Compensation".
Change the tool length compensation data (the 3rd digit) to clear the "Length Compensation".
Figures after the decimal point are also changed in line with the specifications.
I - 181
3. Setup Screen
Operation method (Copying/pasting the tool life data) (M system)
(1) Move the cursor to the line to be copied.
(2) Press the menu Line copy . The menu is highlighted.

The background color of the copied data changes to
light blue.
(The color changes even when scrolling horizontally.)
(3) Move the cursor to the line where the data

is to be pasted.
(4) Press the Line paste menu. The copied tool life management data is written to the
data (excluding the tool No.) in the line where the
cursor is located.
The cursor moves to "ST".
(Note 1) Once copied, the data is held until a new data item is copied.
(Note 2) It is not possible to paste into a line for which a tool No. has not been set.
Operation method (Erasing one line of tool life management data) (M system)
(1) Move the cursor to the line to be erased.
(2) Press the menu Line clear and The menu is highlighted.
A message displays confirming whether it is okay to
INPUT keys.
erase the data.
The background color of the area to be erased
changes to light blue.
(3) Press the Y or INPUT key. One line of the selected life management data is
erased and the menu highlight returns to normal.
Press a key other than Y or INPUT The next line moves up after erasing.
in order not to erase the data.
I - 182
3. Setup Screen
Operation method (Designating and erasing the multiple lines) (M system)
(1) Press the menu Line clear . The menu is highlighted.
(2) Set the range to be erased by marking the A message appears to confirm the erasing.
first and last # Nos. with a "/", and press The background color of the area to be erased
INPUT key. changes to light blue.
122/125 INPUT
(3) Press the Y or INPUT key. The tool life data corresponding to the designated #
No. is erased, and the menu highlight returns to
in order not to erase the data. The next line after the erased range moves up.
Operation method (Registering a group) (M system)
(1) Press the Group regist menu.
(2) Set the No. of the group to be registered. A new group is created and the life management data
25 INPUT displays containing no data.
(Note 1) An error occurs if the same group No. already exists.

(Note 2) The group is not registered if one of the operations below is performed after registering a new
group No..
• If the application is exited without registering even 1 item of tool life data.
• If the screen is changed to that of other than the group unit display.
Operation method (Erasing a group) (M system)
(1) Move the cursor to the group No. to be

erased.
(2) Press the Group delete menu. A message appears to confirm the erasing.
(3) Press the Y or INPUT key. All the tool life management data for the displayed
group No. is erased and the previous group No. data
displays.
Returns to the group list displays if all groups are
erased.
I - 183
3. Setup Screen
3.5.3 Displaying the Life Management Data (L system: Tool life management I)
The tool life management data can be set and displayed. Use the / keys to scroll between screens
if all of the registered tools cannot be displayed on one screen.

(1) # Tool No.
The # No. is highlighted if the usage time reaches the
life time or if the usage count exceeds the life count.
(2) Time Used The integrated time the tool is used. 0:0:0 to 99:59:59 (h:min:s)
This timer value is incremented during cutting.
Life Tool life time 0:0 to 99:59(h:min)
Set the service lifetime. (0:0 = no warning given)
(3) Count Used The integrated count the tool is used. 0 to 9999 (times)
The count goes up when a tool is selected.
Life Tool life count 0 to 9999 (times)
Set the service life count. (0:0 = no warning given)
(4) Status A The tool life management status is indicated. 0 to 2
(left side) 0: Not used
1: Current tool (tool being used)
2: Service lifetime (service life count) is exceeded.
B (Used by machine tool builder) 0 to 99
(right side)
I - 184
3. Setup Screen
Menus (L system)

The copied tool life management data is written to the data in the line C
Line If the copied data is changed after the menu key Line copy
The copied data can be pasted as many times as is required until new
data is copied.
Line The first and the last line No. of the data to be erased is specified with "Designating and
clear a "/" separating the Nos.. erasing a line"
Operation method (Setting the tool life data) (L system)

the , ↑ , ↓ , and
keys.
registered line.

Operation method (Copying/pasting the tool life data) (L system)
(2) Press the menu Line copy . The background color of the copied data changes to
light blue.

is to be pasted.
data in the line where the cursor is located.
I - 185
3. Setup Screen
Operation method (Erasing one line of tool life management data) (L system)
INPUT keys.
erase the data.
The background color of the area to be erased
changes to light blue.
Press a key other than Y or INPUT The next line moves up after erasing.
in order not to erase the data.
Operation method (Designating and erasing the multiple lines) (L system)
(2) Set the erasing range by marking the first A message displays confirming whether it is okay to
and last # Nos. with a "/", and press erase the data.
INPUT key. The background color of the area where the data is
erased changes to light blue.
122/125 INPUT
(Note) If the INPUT key is pressed without setting a # No., the line at the cursor is erased.
I - 186
3. Setup Screen
3.5.4 Displaying the Tool Life Management Data in Group Units (L system: Tool life
Management II)
The tool life management data of an arbitrary group is set and displayed. If the registered tools cannot be
displayed on one screen, scroll the screen using the or key.
This screen is enabled only for tool life management II ("#1096 T_Ltyp" = 2).
(1)
(3)
(2)
(4) (8)
(5) (7)
(6)
By setting parameter "#1107 Tllfsc", it is possible to select the life management data display mode for
multiple groups.
"#1107 Tllfsc" setting value 0 1 2
No. of display groups 1 2 4
Max. No. of registered tools 16 8 4
<Group 1 display mode> (#1107 Tllfsc = 0)
I - 187
3. Setup Screen
<Group information>
Display item Details Setting range
(1) Group Life management group No. 1 to 9999
(2) Form This displays whether to control the currently displayed group 0 : Hours
in usage hours or usage count. 1 : Times
(3) Life This sets the tool life data for the currently displayed group. Usage time:
The following tool life data units display based on the control 0 to 99999999 (s)
method. Usage count:
Usage time : (s) 0 to 999999 (set)
Usage count : (set)
<Life management data within group>

Display item Details Setting range
(4) # This displays whether the tool for which the # No. is highlighted
is a life tool (ST=2) or a skip tool (ST=3).
(5) Tool No. This sets the tool No. 1 to 999999
(6) Comp No. This sets the compensation No. 1 to 80
(7) Used This sets the usage data at such times as when the tool is not Usage time:
an unused tool. 0 to 99999999 (s)
This becomes "0" when the usage data is not set. Usage count:
The following usage data units display based on the control 0 to 999999 (set)
method.
Usage time : (s) Setting can be
Usage count : (set) omitted.
(8) ST This sets the tool status. 0 to 3
This becomes "0" when the tool status is not set.
0: Unused tool Setting can be
1: Used tool omitted.
2: Normal life tool
3: Skipped tool
I - 188
3. Setup Screen
Menus (L system)

This displays the data of a group when that group No. of tool life A "Designating a group
Group management data is set and the INPUT key is pressed. The group No."
No.
No. can be referred to in the group list.
The copied tool life management data is written to the data in the line B
Line If the copied data is changed after the menu key Line copy
The copied data can be pasted as many times as is required until new
data is copied.
Line The first line No. and the last line No. of the data to be erased is "Designating and
clear specified with a "/" separating the Nos. erasing a line"
This changes a group No. A "Changing a group No."
Grp No. If a new group No. is specified and the INPUT key pressed, the
change group No. changes.
An error occurs if a pre-existing group No. is set.
The group active area is changed if parameter "#1107 Tllfsc" is set to C "Changing the active
Group
change 1 or 2. area for multiple group
displays"
Multi Changes to the multiple group life management data display mode C
group based on the parameter "#1107 Tllfsc" setting value.
Group This creates a new group and displays the life management data A "Registering a group"
regist containing no data.
Group This displays the list of tool life data groups. C

list
The multiple group life management data display mode is cancelled. C
Close
Operation method (Designating a group No.) (L system)
(1) Press the Group No. menu. The menu is highlighted.
(2) Designate the group No. to be displayed. The tool life data of the designated group No. appears,
12 INPUT and the cursor moves to the head of the data.
(Note) If a group No. that does not exist is set, a message appears to confirm the creation of a new No..
A new group is created if Y or INPUT is pressed.
When creating a new group, set the method and life data at the end of the group No., separating
the data with a "/". If the method and life data are omitted, a new group is created with method =
0 (usage time), and life data = 0.
I - 189
3. Setup Screen
Operation method (Changing a group No.) (L system)
(1) Press the Grp No. change menu. The menu is highlighted.
(2) Designate the group No. after changing. The group No. changes to "112".
112 INPUT
(Note) An error occurs if the group No. duplicates a pre-existing group No.
Operation method (Setting the tool life data) (L system)

the , ↑ , ↓ , and
keys.
registered line.
Set a tool No. for this line to newly register
tool life management data.

(Note 1) It is not possible to set any other data if the tool No. and compensation No. have not been set.
Operation method (Copying/pasting the tool life data) (L system)
(2) Press the menu Line copy . The background color of the copied data changes to
light blue.

is to be pasted.
data in the line where the cursor is located.
The cursor moves to "Tool No.".
I - 190
3. Setup Screen
Operation method (Erasing one line of tool life management data) (L system)
INPUT keys.
erase the data.
The background color of the area where the data is
Press a key other than Y or INPUT in The next line moves up after erasing.
order not to erase the data.
Operation method (Designating and erasing the multiple lines) (L system)
(2) Set the erasing range by marking the first A message displays confirming whether it is okay to
and last # Nos. with a "/", and press erase the data.
INPUT key. The background color of the area where the data is
1/5 INPUT
(Note) If the INPUT key is pressed without setting a # No., the line at the cursor is erased.
Operation method (Registering a group) (L system)
(1) Press the Group regist menu.
(2) Set the No. of the group to be registered. A new group is created and the life management data
25/1/3000 INPUT displays containing no data.
(Note 1) If the method and life data are omitted, a new group is created with method = 0 (usage time),
and life data = 0.
(Note 2) An error occurs if the same group No. already exists.
(Note 3) The group is not registered if one of the operations below is performed after registering a new
group No.
• If the application is exited without registering even 1 item of tool life data.
• If the screen is changed to that of other than the group unit display.
I - 191
3. Setup Screen
Operation method (Changing the active area for multiple group displays) (L system)
(1) Press the Group change menu. The cursor indicating the active status moves to the
next group.
I - 192
3. Setup Screen
3.6 Workpiece Coordinate System Offset
This function allows the user to set and display the coordinate system offset controlled by the NC.
Using the option, the number of coordinate system offset sets can be increased by 48 or 96 sets.
(Note) The G92/G52 coordinate system offset cannot be set.
(1)
(2)
(3)
Display items

(1) Coordinate system offset This sets and displays the offset amount Basic machine coodinate system M
area for the workpiece coordinate system (G54
- G59), or the extension workpiece External workpiece
coordinate system
coordinate system (G54.1Pn).
Use the menu operation or page change R
key to specify which workpiece coordinate Reference
G55 W2 point
system offset to display or set. workpiece
The workpiece coordinate system offset coordinate
system
amount data can be set in absolute or
additional mode.
G54 workpiece W1
coordinate system
(2) EXT offset area This displays or sets the offset amount for the external workpiece system.
(3) G92/G52 offset area This displays the offset amount for G92 or the local coordinate system.
The offset amount of the corresponding local coordinate system (G52) is displayed
only when the cursor is at G54 to G59.
! CAUTION
command in next block or after several subsequent blocks.
I - 193
3. Setup Screen
Menus

This inputs the offset amount with the absolute mode. C 3.6.1 Setting the
= Input
Coordinate System
Offset
This inputs the offset amount with the additional mode. C
+ Input
This sets the workpiece coordinate system offset so that the current C 3.6.3 Setting the Work
Easy
setting machine coordinate becomes the workpiece coordinate zero point. Piece Coordinate Origin
Only the axis at the cursor position is set.
This displays the G54 - G59 workpiece coordinate system offset C 3.6.1 Setting the
G54-G59 amount. The cursor moves to the G54 offset. This menu can be used Coordinate System
when the G54 – G59 offsets are not displayed. Offset
Enter the P number displayed at the screen to display the extension A
workpiece coordinate (G54.1 Pn) offset in the coordinate system
G54.1 offset area. This menu is not displayed if the extension workpiece
P coordinate system offset option is disabled.
If the local coordinate system offset (G52) displays in the G92/G52
area, the display changes to G92.
This displays the G92 or G52 coordinate system offset amount. The C
Coord
G92/G52 G92 offset data is always displayed when the cursor is not at the G54
to G59 offset data.
All All coordinate system offset amounts for all axes are erased with the A 3.6.2 Erasing the
clear exception of G92 and EXT. Coordinate System
Offset Amount
All axs This erases the local offset data for all axes corresponding to the A
clear offset data of the coordinate system where the cursor is located.
This can be selected when the number of enabled axes is 6 or over. C
Next
axis The displayed axes are changed to axes 1 – 5, and axis 6 and over.
(Note) This displays when there are 6 or more axes.
I - 194
3. Setup Screen
3.6.1 Setting the Coordinate System Offset
Operation method (Setting the workpiece coordinate system G54 - G59 offset amount)
(1) Press the G54-G59 menu. The G54 - G59 workpiece coordinate system offset
displays.
(2) Use the ( , ) keys to move the

cursor to the workpiece coordinate system
offset to be set.
Use the , page keys to change the coordinate system display.

Refer to the "Changing the offset amount using the page change keys (previous page: ,
next page: )" section in "3.6.4 Changing the coordinate system display" for further details.
(3) Use the ↑ , ↓ keys to move the cursor
to the axis for which data is to be set.
(4) Set the offset amount. The set data displays and the cursor moves to the next
122 INPUT data.
This setting can be made by pressing the
menu =INPUT key instead of the
INPUT key.
(5) Set other data using the same method.
(Note) It is possible to perform additional input by pressing the menu +INPUT key instead of the
INPUT or menu =INPUT keys.
[Ex.] If the original data is 122.000:
1.234 [+INPUT] → 122.000 + 1.234 = 123.234
Setting the external coordinate system offset amount
Set the external coordinate system offset amount to keep the current workpiece coordinate system offset
amounts from G54 to G59, and also apply an offset to the entire system.
Furthermore, it is also possible to use the data transfer function to write data directly to the external
coordinate system offset (EXT).
(Refer to "6.2 Input/output screen" for details of the data transfer function.)
I - 195
3. Setup Screen
3.6.2 Erasing the Coordinate System Offset Amount
Operation method (Erasing the coordinate system (excluding G92) offset amount where the cursor is
displayed for all axes.)
(1) Press the menu All axs clear menu. The menu is highlighted.
erase the data.
(2) Press the Y key. All of the coordinate system indicated by the cursor is
cleared to zero.
In addition, all axes data of the local offset (G52) for
the coordinate system will be erased.
Operation method (Erasing all axis offset data of all coordinate systems (excluding G92 and EXT))
(1) Press the menu All clear menu. The menu is highlighted.
erase the data.
(2) Press the Y key. All coordinate system data is erased.

In addition, all axes data of the local offset (G52) for
the G54 to G59 coordinate systems will be erased.
(Note) G92 data cannot be erased.
3.6.3 Setting the Workpiece Coordinate Origin

Press the menu Simple settings key to set the coordinate system offset so that the current machine
position (for all axes) becomes the workpiece coordinate origin. It is only possible to set those axes where the
cursor is located.
If the menu Easy setting is pressed when there is the cursor in coordinate system offset (G54 to G59), the
local offset (G52) data of the axis will be also erased.
I - 196
3. Setup Screen
3.6.4 Changing the Coordinate System Display
Use the tab keys to change the coordinate system offset cursor position.
Press the Tab key to change the cursor position.
G54 G55 G56
EXT G92
Changing the coordinate system offset using the page change keys (previous page: , next page: )
Use the page change keys to change the coordinate system offset display as shown below.
Coordinate system display
G54 G55 G56
G57 G58 G59
G54.P1 G54.P2 G54.P3
G54.P4 G54.P5 G54.P6
G54.P7 G54.P8 G54.P9
An option is required for the G54.P1 - P96 workpiece coordinate system offset display.
I - 197
3. Setup Screen
3.7 Workpiece Measurement
3.7.1 Workpiece Measurement (M system)

Move the sensor attached to the spindle using manual feed or handle feed to contact the workpiece, measure
the coordinate position, and then set that measurement result for the workpiece coordinate system offset
amount.
There are three measurement patterns: surface measurement, hole measurement, width measurement, and
rotation measurement.
For the rotation measurement, the measurement result is set in the workpiece offset (rotation center) and
parameters "#8624 Coord rot centr(V)", "#8626 Coord rot vctr(H)", and "#8627 Coord rot angle".
■For surface measurement (As for the hole or width measurement, the guide drawing differ.)
(2)
(1)
(3)
(4)
(6)
(5)
■For rotation measurement

(2)
(1)
(3)
(7)
(4)
(8) (6)
(5)
(9)
I - 198
3. Setup Screen
Display items

(1) Measurement counter Displays the measurement position.
The measurement axis is compatible with base system parameters "#1026 base_I",
"#1027 base_J", and "#1028 base_K". (Hereafter indicated as I=X, J=Y, and K=Z
axes in this manual.)
The measurement position becomes blank when setting the coordinate system offset
amount, resetting the NC, or changing the measurement mode (when face meas,
hole meas, width meas, or rotate meas menu is selected).
The display contents differ depending on the measurement pattern (surface
measurement, hole measurement, width measurement, or rotation measurement).
Surface measurement Displays the calculated measurement position from the skip position for each axis (X-,
counter Y-, Z-axes).
Hole measurement Displays 3 (A, B, C) measurement positions (X-, Y-axes).
counter
Width measurement Displays 2 (A, B) measurement positions (X-, Y-, Z-axes).
counter
Rotation measurement Displays 3 (A, B, C) measurement positions (X-, Y-axes).
counter
(2) Manual measurement Displays the manual measurement status.
status display Refer to the "Manual measurement status display" section in "3.3.1 Tool
Measurement (M system)" for further details.
(3) Guide drawing Displays the measurement image.
The contents of the guide drawing differ depending on the measurement pattern
(surface measurement, hole measurement, width measurement, or rotation
measurement).
(4) Sensor length and Sensor length : Displays the length to the tip of the touch sensor.
diameter ("#8701 Tool Length" setting value)
Sensor diameter : Displays the diameter of the ball at the tip of the touch sensor.
("#8702 Tool Dia" setting value)
(5) Coordinate system offset Displays the currently selected coordinate system offset.
(6) Measurement position Displays the measurement position for all axes.
counter X axis : X axis machine position + sensor radius +center compensation (Horizontal)
Y axis : Y axis machine position + sensor radius +center compensation (Vertical)
Z axis : Z axis machine position - sensor length
4th axis and over : Respective machine position
Sensor length : "#8701 Tool Length"
Sensor radius : "#8702 Tool Dia"/2
Center compensation (H) : "#8703 OFFSET X"
Center compensation (V) : "#8704 OFFSET Y"
(7) Center shift amount Displays the shift amount of the coordinate rotation center.
(8) Coordinate rotation center Displays the coordinates that are the center during coordinate rotation.This is the
setting value of "#8623 Coord rot centr (H)" and "#8624 Coord rot centr (V)".
(9) Coordinate rotation angle Displays the rotation angle during coordinate rotation.This is the setting value of
"#8627 Coord rot angle".
I - 199
3. Setup Screen
Menus

The results calculated from the measurement counter are set in the C
displayed workpiece coordinate system offset.
Only the axis for which a value is displayed in the measurement
Coord
write counter can be set.
(Note) If the workpiece coordinate system to be set is G54 to G59,
the local coordinate system offset value will be zero. (Only for
the measured axis.)
This selects the displayed workpiece coordinate system from the C
sub-menu (G54 - G59). Select the workpiece coordinate system to
Coord display the selected workpiece coordinate system offset in the
G54-G59
coordinate system offset section.
(Perform the offset amount setting at the menu Coord write key.)
Input the P number to display the selected extension workpiece A
coordinate system (G54.1 Pn) offset in the coordinate system offset
Coord section.
G54.1 P (Perform the offset amount setting at the menu Coord write key.)
This menu does not display if the extension workpiece coordinate
system offset option is disabled.
This displays the external workpiece coordinate system offset in the C
Coord coordinate system offset section.
EXT
(Perform this setting at the menu Coord write key.)
This creates a false signal when performing simple measurement B
(measurement without using the touch sensor) and reads the skip
SkipPos position. Press this menu to display the measurement position
take in
measured from the machine position of the axis moved last (axis 1 or
2) at the measurement counter.
Face This enables surface measurement. B 3.7.1 Carrying Out
meas Surface measurement is possible when the power is turned ON. Surface Measurement
Hole This enables hole measurement. (The cursor moves to the B 3.7.2 Carrying Out Hole
meas measurement counter point A.) Measurement
Width This enables width measurement. (The cursor moves to the B 3.7.3 Carrying Out Width
meas measurement counter point A.) Measurement
Rotate This enables rotation measurement. (The cursor moves to the B 3.7.4 Carrying Out
meas measurement counter point A.) Rotation Measurement
This changes the axes displayed at the coordinate system offset and C
Next measurement position counter from axis 1 - 5, and axis 6 and over.
axis
(Note) This displays when the number of enabled axes is 6 or over.
Center This sets the center shift amount. (The cursor moves to the 1st axis of A 3.7.4 Carrying Out
shift "center shift (S)" when this is selected.) Rotation Measurement
Rotate This sets the coordinate rotation center. (The cursor moves to the 1st A
center axis of "coordinate rotation center" when this is selected.)
Rotate This sets the coordinate rotation angle. (The cursor moves to the A
angle "coordinate rotation angle" when this is selected.)
I - 200
3. Setup Screen
Details of the "Measurement counter" and "Guide drawing" display areas
Menu Measurement counter Guide drawing

Face
meas
Hole
meas
Width
meas
Rotate
meas
I - 201
3. Setup Screen
3.7.1.1 Carrying Out Surface Measurement
Outline
When carrying out surface measurement, the position of each axis is measured and the measurement results
are set in the workpiece coordinates system offset. The measurement position displays at the measurement
counter.
<Measurement using the touch sensor>

Measurement counter X = X axis skip position + sensor radius (Note)
Measurement counter Y = Y axis skip position + sensor radius (Note)
Measurement counter Z = Z axis skip position - sensor length
(Note) The sign (+ and -) changes depending on the direction of the axis moved last.
Item Reference
Sensor radius "#8702 Tool Dia"/2
Sensor length "#8701 Tool Length "
<Simple measurement (measurement without using touch sensor)>

Measurement counter X : X axis measurement position
Measurement counter Y : Y axis measurement position
Measurement counter Z : Z axis measurement position
Operation method
(1) Press the Face meas menu. The menu is highlighted.
(2) Perform the reference position return

command, etc. to position the tool at the
basic point.
(3) Turn ON the measurement switch on the The message "On meas" appears.
machine operation board.
(4) Move the tool near the workpiece using

manual feed and manual handle feed.
<With the touch sensor>

(5) Move the tool in the X-direction until the Upon contact, the axis automatically contacts the
sensor contacts the workpiece. workpiece again. The measurement position
measured from the skip position displays in the
measurement counter X axis section.
I - 202
3. Setup Screen
<Without the touch sensor (simple measurement)>

(5) Move the tool in the X-direction to the The skip position is calculated and the result displays
arbitrary position and press the menu in the measurement counter X axis section.
SkipPos take in .
(6) Select the workpiece coordinate system

offset in which the measurement data will
be set.
(Example) Press the menus
Coord G54-G59 G55 to select
G55.
(7) Press the Coord write menu. The value achieved by adding or subtracting the
external workpiece offset to or from the X axis
measurement position based on the "#8709 Ext work
sign rvs" is set in workpiece coordinate system
selected at (6).
The measurement counter displays blank.
(8) Carry out the operations in steps (4) to (7)

in the same way for the Y and Z axes.
(9) Return the tool to the reference position, The message "On meas" disappears.
and turn the measurement switch OFF.
3.7.1.2 Carrying Out Hole Measurement
Outline
When carrying out hole measurement, three positions (A, B, and C) are measured, and the hole center
position calculated from the three measured positions is set in the workpiece coordinate system offset. The
measurement position displays at the measurement counter.

Measurement counter X = X axis skip position
Measurement counter Y = Y axis skip position

Measurement counter X = X axis machine position + center compensation (H) + skip past amount
(Horizontal axis) (Note)
Measurement counter Y = Y axis machine position + center compensation (V) + skip past amount
(Vertical axis) (Note)
(Note) The skip past amount is added for only the axis that moved last.
The sign ( + or - ) of the past amount depends on the movement direction of the axis.
Item Reference
Center compensation (H) "#8703 OFFSET X"
Center compensation (V) "#8704 OFFSET Y"
Skip past amount (horizontal axis) "#8707 Skip past amout (H)"
Skip past amount (vertical axis) "#8708 Skip past amout (V)"
I - 203
3. Setup Screen
Operation method
(1) Press the Hole meas menu. The menu is highlighted and the cursor displays at
point A.
Use the ↑ , ↓ keys to move to points B and C.

basic point.
(4) Move the tool into the hole using manual

feed and manual handle feed.

(5) Position the tool against the inner wall of
the hole. Contact is performed by moving
a single axis.
Upon contact, the axis automatically contacts the hole

wall again. The skip position displays in the
measurement counter point A, X and Y axis section.
The cursor moves to point B. For point C, the cursor
moves to point A.

(5) Move the tool in the X-direction to the The skip position is calculated and the result displays
arbitrary position and press the menu in the measurement counter X axis section.
SkipPos take in .
moves to point A.
(6) Measure points B and C in the same way.

be set.
G55.
(8) Press the Coord write menu. The hole center position is measured, and based on
the "#8709 Ext work sign rvs", value achieved by
adding or subtracting the external workpiece to or from
the measurement result is set in workpiece coordinate
system selected at (7). The measurement counter
displays blank.
I - 204
3. Setup Screen
3.7.1.3 Carrying Out Width Measurement
Outline
When carrying out width measurement, two positions (A, and B) are measured, and the width center position
calculated from the two measured positions is set in the workpiece coordinate system offset. The
measurement position displays at the measurement counter.

Measurement counter X = X axis skip position
Measurement counter Y = Y axis skip position
Measurement counter Z = Z axis skip position - sensor length

Measurement counter Z = Z axis machine position - sensor length
The sign ( + or - ) of the past amount depends on the movement direction of the axis.
Item Reference
Sensor length "#8701 Tool Length"
Skip past amount (horizontal axis) "#8708 Skip past amout (V)"
Operation method
(1) Press the Width meas menu. The menu is highlighted and the cursor displays at
point A.
Use the ↑ , ↓ keys to move to points A and B.

basic point.
(4) Move the tool to the center of the groove

using manual feed or manual handle feed.
I - 205
3. Setup Screen

(5) Position the tool against the inner wall of
the groove. Contact is performed by
moving a single axis.
Upon contact, the axis automatically contacts the

groove wall again. The skip position displays in the
measurement counter point A.
The cursor moves to point B. For point B, the cursor
moves to point A.

(5) Move the tool to the arbitrary position and The skip position is calculated and the results displays
press the menu SkipPos take in . in the measurement counter X axis and Y axis section.
The cursor moves to point B. For point B, the cursor
moves to point A.
(6) Similarly, position the tool against the Upon contact, the axis automatically contacts the
opposite side. groove wall again. The skip position displays in the
measurement counter point B.

be set.
G55.
(8) Press the Coord write menu. The width center position is measured, and based on
adding or subtracting the external workpiece offset to
or from the measurement result is set in workpiece
coordinate system offset G55 (coordinate system
selected at (7)). The measurement counter displays
blank.
(9) Carry out the operations in steps (4) to (8)

in the same way for the Y and Z axes.
(10) Return the tool to the reference position, The message "On mea" disappears.
I - 206
3. Setup Screen
3.7.1.4 Carrying Out Rotation Measurement
Outline
When carrying out rotation measurement, the offset (rotation center and rotation angle) of the rotary
coordinate system is measured, and the results are set to the workpiece coordinate system offset (rotation
center) and the parameters "#8623 Coord rot centr(H)", "#8624 Coord rot centr(V)", and "#8627 Coord rot
angle".
<Measurement using touch sensor>

Measurement counter X = X axis skip position (Machine position)
Measurement counter Y = Y axis skip position (Machine position)

The sign ( + or - ) of the skip past amount depends on the movement direction of the axis.
Item Reference
Skip past amount (vertical axis) "#8708 Skip past amout (V)"
Operation method (Setting the center shift amount)
(1) Press the Rotate meas menu. The pop-up window for the rotation measurement
appears.
The measurement counter becomes active and the
cursor appears at the 1st axis.
(2) Press the Center shift menu. The menu is highlighted.

"C shift (S)" column becomes active and the cursor
appears at the 1st axis.
The measurement counter active display returns to
normal.
(3) Input the center shift amount (Si). The value is input and the cursor moves to the 2nd
10.000 INPUT axis.
(4) Input the center shift amount (Sj). The value is input, however, the cursor does not move.
-5.000 INPUT
(5) Press the Center shift menu. The menu highlight returns to normal.
"C shift (S)" column active display returns to normal.
I - 207
3. Setup Screen
Operation method (Setting the center and angle of the coordinate rotation)
The setting of the parameters "#8623 Coord rot centr(H)", "#8624 Coord rot centr(V)", and "#8627 Coord rot
angle" can be changed.
(1) Press the Rotate meas menu. The pop-up window for the rotation measurement
appears.
(2) Press the Rotate center menu. The menu is highlighted.

"Coord center" column becomes active and the cursor
appears at the 1st axis.
The measurement counter active display returns to
normal.
(3) Input data in the 1st axis of "Coord center" The value is input and the cursor moves to the 2nd
column. axis.
0 INPUT
(4) Input data in the 2nd axis of "Coord center" The value is input, however, the cursor does not move.
column.
0 INPUT
(5) Press the Rotate center menu. The menu highlight returns to normal.
"Coord center" column active display returns to
normal.
(Note) Set the angle of the coordinate rotation in the same manner.
I - 208
3. Setup Screen
Operation method (Carrying out the rotation measurement using touch sensor to set the
measurement results to the workpiece coordinate offset)
(1) Press the Rotate meas menu. The menu is highlighted and the cursor appears at
point A.
The cursor can be moved to A, B, or C, using ↑ and
↓ keys.
(2) Set the parameter "#8116 Coord rot para

invd" to "1" (invalid).
(3) Set the following parameters to "0". The value is input, however, the cursor does not move.
#8623 Coord rot centr(H)
#8624 Coord rot centr(V)
#8627 Coord rot angle
(Note) These parameter should be set to "0" to set the measured value to them.
If the value other than "0" has been set, an error occurs when writing to the coordinate
system.
(4) Turn the manual absolute switch ON. The value is input and the cursor moves to the 2nd
axis.

basic point.
(7) Referring to "Setting the center shift The menu highlight returns to normal.
amount", set the center shift amount. The measurement counter becomes active and the
cursor appears at the first axis.
This setting is not necessary if the
"Coord center" column active display returns to
coordinate rotation center is served as the
normal.
workpiece coordinate zero point.
<Measurement using touch sensor>

(8) Make the spindle contact the workpiece
using manual feed or manual handle feed.
Upon contact, the skip position displays in the

measurement counter point A.
moves to point A.
I - 209
3. Setup Screen
<Simple measurement (without using touch sensor)>

(8) Move the spindle to the arbitrary position The skip position is calculated and the results appear
and press the SkipPos take in menu. in the measurement counter point A.
moves to point A.
(9) Measure points B and C in the same way.

be set.
(Example) To select G55, press the
Coord G54-G59 G55 menus.
(11) Press the Coord write menu. The hole center position is measured, and based on
adding or subtracting the external workpiece to or from
the measurement result is set in workpiece coordinate
system selected at (7). The measurement counter
displays blank.
I - 210
3. Setup Screen
3.7.1.5 Performing Automatic Recontact When Contacting the Workpiece

When performing workpiece position measurement in either the JOG or handle mode, the following
operations (automatic recontact) are performed after contacting the workpiece.
(1) Moves to the measurement point using
either the JOG or handle mode.
(2) Stops at the measurement point.

Skip
(3) Returns by the measurement parameter

return amount (#8705).
Return
amount
(4) Moves to measurement point again at the

measurement parameter feedrate (#8706).
(5) Stops at the measurement point. (The skip

position is read.) Skip
(6) Returns by the measurement parameter

return amount (#8705).
Return
amount
(7) The next measurement can be performed

after automatically contacting the
workpiece again.
The return speed for (3) and (6) is 40 times the measurement parameter feedrate (#8706). However, if
the return speed is faster than rapid feedrate (override 100%), the rapid feedrate will become the return
speed.
I - 211
3. Setup Screen
3.7.2 Workpiece Measurement (L system)

The external workpiece coordinate offset data for the Z axis can be set by cutting the workpiece face by
means of manual operations and inputting the workpiece measurement signal.
By pressing the menu key, data can be set in the Z axis of an arbitrary coordinate offset.
Coordinate offset setting for the Z axis (2nd axis) of the part system 1 to 4 is possible.
Note that the workpiece coordinate offsets for multiple part systems cannot be measured at the same time.
For signals and R registers, refer to the instruction manual issued by the machine tool builder.
(Note) Measurement is disabled for the part system with one-axis structure.
Example of measurement of external workpiece coordinate offset data for Z axis

X axis
Tool post Machine

zero point
Workpiece
Z axis
Workpiece coordinate
zero point
(5)
(1)
(2)
(6)
(3)
(4)
Manual numerical value command can be executed when manual numerical value command window is
displayed by inputting an address key such as MST, etc.
I - 212
3. Setup Screen
Display items

(1) External workpiece This displays the external workpiece coordinate offset.
coordinate offset When the workpiece measurement signal is input, the measurement result is set to
2nd axis of the external workpiece coordinate.
(Note) The 5th axis and following are not displayed.
(2) Tool offset num This displays the compensation No. of tool length data used by automatic calculation.
(Note 1) If an illegal value is set, the value is blank. ("0" is displayed.)
(Note 2) The No. is displayed by BCD code.
(3) Wear offset num This displays the compensation No. of tool nose wear data used by automatic
calculation.
(Note 1) If an illegal value is set or tool nose wear data is not used for measurement
("#1226 aux10/bit0" is 1), the value is blank. ("0" is displayed.)
(Note 2) The No. is displayed by BCD code.
(4) Coordinate system offset This displays the coordinate system offset in which the measurement result is written
when "MeasVal take in" menu is pressed. G54 is displayed in default.
When "MeasVal take in" menu is pressed, the measurement result is set to 2nd axis
of the external workpiece coordinate.
(Note 1) If an illegal value is set, the value is blank. ("0" is displayed.)
(Note 2) The display of Coordinate system offset area is switched by page
changeover keys. Refer to the section "3.6.4 Changing the Coordinate
System Display".
(5) On mea When the measurement switch is ON and the operation mode is manual mode
([Handle], [Jog], [Rapid Traverse], or [Step]), "On mea" is displayed, and the
workpiece can be measured by the workpiece measurement signal.
(6) Guide drawing This displays the measurement area.
I - 213
3. Setup Screen
Menus

This selects the coordinate system offset which sets the measurement C
value when "MeasVal take in" is executed from sub-menu (G54 -
Coord
G54-G59 G59). The workpiece coordinate system offset data is displayed after
selected. However, the cursor is not displayed and the data cannot be
set.
This selects the coordinate system offset which sets the measurement A
value when "MeasVal take in" is executed. Input the P No. to display
the selected external workpiece coordinate system (G54.1 Pn) offset
Coord
G54.1 P in the coordinate system offset area. However, the cursor is not
displayed and the data cannot be set.
If the option of external workpiece coordinate system offset is invalid,
this menu is displayed in gray and cannot be selected.
This measures G54 - G59 and G54.1Pn. When this menu is pressed, B
the workpiece coordinate offset data is calculated from the machine
MeasVal
take in coordinate, the used tool length, the tool nose wear compensation
amount and the external workpiece coordinate offset, and the data is
stored in Z axis of the selected coordinate system offset.
I - 214
3. Setup Screen
Operation method (When the workpiece measurement signal is used)
(1) Execute the reference position return. The coordinate system is established.
(Note 1) If the workpiece is measured without
establishing the reference position return, the
operation message "Meas axis not returned
to ref. position" appears.
(2) Set the mode selection switch to the

manual mode ([Handle], [Jog], [Rapid
Traverse]) or [Step]).
(3) Set "1" to "Tool length measurement 2"

signal.
(4) Select whether to measure the workpiece

coordinate on the main spindle side or
sub-spindle side by using tool presetter
sub-side valid signal.
(Note 1) Hold the state of this signal until
the measurement with the
selected tool is completed.
(5) Issue the T command with MDI operation, The tool is selected.
etc. (Note 1) Set the selected tool compensation No. in R
register.
The set R register differs according to
parameter setting and the state of the tool
presetter sub-side valid signal.
(Note 2) Set the "tool length/wear data" for the tool
being used beforehand.
(6) Cut the workpiece face slightly to even it.
(Note 1) Do not move the tool in the

detection of Z axis after cutting
the workpiece face.
(Note 2) If the workpiece does not need to
be cut, carry out positioning to
the measurement position.
(7) Input the workpiece measurement signal. The Z axis external workpiece coordinate offset data is
automatically calculated from the tool compensation
data of the used tool and the machine value at the
point this signal is input. The results are set as the
data.
(8) Turn "Tool length measurement 2" signal Measurement of the external workpiece coordinate
OFF. offset is completed.
I - 215
3. Setup Screen
Operation method (When the MeasVal take in menu is used)
(1) Execute the reference position return. The coordinate system is established.
(Note 1) If the workpiece is measured without
establishing the reference position return, the
operation message "Meas axis not returned
to ref. position" appears.
(2) Set the mode selection switch to the

manual mode ([Handle], [Jog], [Rapid
Traverse]) or [Step]).
(3) Select an arbitrary coordinate system The designated coordinate system offset is selected.
offset. (Note 1) When switching to an arbitrary coordinate
system offset display, press one of these;
"Coord G54 - G59" "Coord G54.1P" menu or
page key.
(4) Select whether to measure the workpiece

coordinate on the main spindle side or
sub-spindle side by using tool presetter
sub-side valid signal.
(Note 1) Hold the state of this signal until
the measurement with the
selected tool is completed.
(5) Issue the T command by MDI operation, The tool is selected.

etc. (Note 1) Set the selected tool compensation No. in R
register.
The set R register differs according to
parameter setting and the state of the tool
presetter sub-side valid signal.
(Note 2) Set the "tool length/wear data" for the tool
being used beforehand.
(6) Cut the workpiece face slightly to even it.
(Note 1) Do not move the tool in the

detection of Z axis after cutting
the workpiece face.
(Note 2) If the workpiece does not need to
be cut, carry out positioning to
the measurement position.
(7) Press the menu MeasVal take in. The workpiece measurement is executed.
The operation message "OK? (Y/N)" appears, so
press the Y or INPUT.
The Z axis external workpiece coordinate offset data is
automatically calculated from the tool compensation
data of the used tool and the machine value at the
point this signal is input. The results are set as the
data.
I - 216
3. Setup Screen
Details of automatic calculation expression (When the workpiece measurement signal is used)
The external workpiece coordinate offset data is automatically calculated with the following expression.
External workpiece coordinate offset = Machine coordinate value - Tool compensation data
The tool compensation data used for the measurement is selected with the base specification parameter
"#1226 aux10 bit0".
#1226 aux10 bit0 Tool compensation data
0 Tool length data + nose wear data
1 Tool length data
External workpiece coordinate offset
Machine value
Tool
compensation
amount Tool rest Basic machine
coordinate zero point
Workpiece coordinate zero point
Details of automatic calculation expression (When the MeasVal take in menu is used)
The workpiece coordinate offset data is automatically calculated with the following expression.
The calculation expression changes according to basic specification parameter "#8709".
When "#8709" is "0":
Workpiece coordinate offset
= Machine coordinate value - External workpiece coordinate offset - Tool compensation data
When "#8709" is "1":
Workpiece coordinate offset
= Machine coordinate value + External workpiece coordinate offset - Tool compensation data
The tool compensation data used for the measurement is selected with the base specification parameter
"#1226 aux10 bit0".
#1226 aux10 bit0 Tool compensation data
0 Tool length data + nose wear data
1 Tool length data
Workpiece
coordinate offset External workpiece
coordinate offset
Machine value
Tool
compensation
amount Tool rest Basic machine
coordinate zero point
Workpiece coordinate zero point
I - 217
3. Setup Screen
The selected tool compensation No.
For the compensation No. of the tool length and tool nose wear data used by automatic calculation, the No.
set in R register in the following table is used.
Tool length Tool nose wear
#1218
#1098 Tlno. #1130 set_t compensation No. compensation No.
aux02 bit4
Main side Sub-side Main side Sub-side
R2600, R2604,
0 0/1 0/1
R2601 R2605
R2600, R2604,
0 R536, R537
0 R2601 R2605
1 1 R2602, R2606,
1 0/1 R2603 R2607
(Note 1) When the compensation No. is 0, the compensation amount will be calculated as "0".
(Note 2) If the compensation No. exceeds the number of specified offset sets, the operation message
"Offset No. not found" appears.
(Note 3) If the input data exceeds the setting range, the operation message "Data range error" appears.
(Note 4) If the data protect key 1 is valid, the operation message "Data protect" appears.
(Note 5) Whether to use the main side or sub-side is selected with the tool presetter sub-side valid signal.
(OFF: Main side, ON: Sub-side)
(Note 6) Set the compensation No. in R register by the BCD code.
I - 218
3. Setup Screen
3.8 User Parameters
3.8 User Parameters
The parameters contain the user and machine parameters.

This chapter explains the details and operations for the user parameters.
<High-accuracy parameters>: Part system based
(1)
(2)
<High-accuracy parameters>: Axis based
(1)
(2)
I - 219
3. Setup Screen
3.8 User Parameters
Display items

(1) Parameter display area Press the parameter selection menu Process param or Hi-prec param keys
etc. to change the parameter display contents.
(2) Input section The set key displays. Press the INPUT key to set the display data in the
parameter where the cursor is located.
Menus

Process This changes the display of each parameter type. B 3.8.2 Setting the
param (Note) The barrier data only displays for the L system. Parameters
Fixed
cycle
Control
param
Operate
param
I/O
param
Ethernet
param
Link
param
Subpro
stor
Axis
param
Barrier
data
Hi-prec
param
Hi-prec
axis
This selects an arbitrary parameter number. A 3.8.1 Selecting the
Param Set the parameter number and press the INPUT key to move that Parameter Number
No. number to the top and display the parameter. The cursor also moves
to that number.
Area This copies the parameter setting values in the designated range. A 3.8.3 Copying/Pasting
copy The range is designated with numbers. Parameters
This pastes the range of parameters designated in area copy. They A
are pasted in a parameter corresponding to the axis or part system
Area where the cursor is.
paste
Once copied, a parameter can be pasted any number of times until a
new parameter is copied.
This can be selected if the total number of part system display axes is C
Next 5 or more.
axis This is used at the parameter screen with the array structure for each
axis.
Close
I - 220
3. Setup Screen
3.8 User Parameters
3.8.1 Selecting the Parameter Number

Press the menu Param No. key to select an arbitrary parameter number.
3.8.2 Setting the Parameters

The method of setting the parameters is explained. Refer to "3.8.8 User Parameters" for details of each
parameter setting range.
Operation method (Normal setting: Set "100" for X1 axis of "#8204 OT-" parameter)
(1) Press the Axis param menu. The axis parameter displays.
(2) Use the ↑ , ↓ , |← and →| The cursor moves to the position where the data is to
keys to move the cursor to the setting be set (X1 axis).
position.
(3) Enter a value. The set value displays and the cursor moves one
100 INPUT position downwards.
Operation method (Batch data setting: Set "200" for Y1 axis and "250" for Z1 axis of "#8204 OT-")
(1) Press the Axis param menu. The axis parameter displays.
(2) Use the ↑ , ↓ keys to move the The cursor moves to the position where the data is to
cursor to the setting position. be set.
(3) Enter a value. The set value displays and the cursor moves one
Input format: position downwards.
1st column/2nd column/3rd column
/200 /250 INPUT
(Note 1) When a parameter is changed and PR displays at the top of the screen, reboot the machine
to enable that parameter change.
(Note 2) When the INPUT key is pressed without inputting a value, the parameter setting value is not
changed, and the cursor moves.
(Note 3) Parameters that can be set simultaneously must display within the currently displayed three
columns.
(Note 4) If parameter values are simultaneously input in multiple columns, settings are made from the
currently displayed column on the left side, no matter which column the cursor is positioned.
I - 221
3. Setup Screen
3.8 User Parameters
3.8.3 Copying/Pasting Parameters

Parameters can be copied and pasted in a parameter with the same number for another axis or part system.
Operation method (Specifying and copying the parameter where the cursor is located)
(1) Press the Area copy menu. The menu is highlighted.
(2) Move the cursor to the position of the The copy position displays in the selected area color.
parameter to be copied and press the The menu highlight returns to normal.
INPUT key.
Operation method (Copying parameter numbers in a specific range)
(1) Move the cursor to the display area of the

axis or part system to be copied.
(2) Press the Area copy menu. The menu is highlighted.
(3) Designate the copy range. The range to be copied displays in the selected area
Format: First No./Last No. color.
8701/8705 INPUT The menu highlight returns to normal.
An "E" can be used if the last number to be

copied is the last number in the currently
displayed parameter type.
(Ex.) 8701/E
(Note 1) The selected area color of the copied area returns to normal when the copied data is pasted.
However, the copied range can still be pasted until the parameter type display is changed.
(Note 2) Only the currently displayed parameter type can be copied.
I - 222
3. Setup Screen
3.8 User Parameters
Operation method (Pasting the copied parameters)
(1) Move the cursor to the axis or part system

display area where the data will be pasted.
(2) Press the Area paste menu. The menu is highlighted and a confirmation message
displays.
(3) Press the Y or INPUT key. The copied data is written to the parameter where the
cursor is located.
The copied data is not written in when the The menu highlighted returns to normal.
N key is pressed.
(Note) If the relevant parameter is changed after specifying the range to be copied, the value after the
change is pasted.
I - 223
3. Setup Screen
3.8 User Parameters
3.8.4 Parameter Configuration

The parameter number range and permissible operations for all parameter types are shown below.
: Can be used, : Operable under certain conditions (Refer to the section below for conditions.)
Next axis System change Area copy Area paste
Parameter type Parameter No.
menu Key menu menu
(Note 3) (Note 3) (Note 3)
Process parameter 8001 to 8011 -
8041, 8042
8071 to 8075
8701 to 8706
Fixed cycle 8012 to 8018 -
8051 to 8059
8083 to 8086
Control parameter 8101 to 8124 - - - -
Operation parameter 8501 to 8506 - - - -
I/O parameter 9001 to 9014 - - - -
9101 to 9130
9201 to 9230
9301 to 9330
9401 to 9430
9501 to 9530
Ethernet parameter 9701 to 9706 - - - -
9711 to 9721
9731 to 9741
9751 to 9761
9771 to 9781
Computer link 9601 to 9630 - - - -
parameter
Subprogram storage 8800 to 8889 -
designation
parameter
Axis parameter 8201 to 8212 -
(Note 3)
Barrier data (Note 4) 8300 to 8319 -
High precision 1149, 1150 -
parameter 1205 to 1207
1209
1568 to 1571
8019 to 8023
8025 to 8030
8033 to 8037
8090 to 8094
(Note 2)
High precision axis 2001, 2002 -
(Note 1) (Note 2)
parameter 2010
(Note 1) This is valid only when the total number of valid NC axes and PLC axes in the entire part system
is four or more.
(Note 2) This is valid only when the total number of valid NC axes and PLC axes in the entire part system
is two or more.
(Note 3) This is valid only when the number of valid part systems is two or more.
(Note 4) The barrier data appears only for the L system specifications.
I - 224
3. Setup Screen
3.8 User Parameters
3.8.5 Echoback
When the cursor moves to a parameter with 16 or more characters, all of the set value is echoed back to the
input area. The value of such parameter is displayed with "…" displays in the data field.
Echoback parameters
Parameter type Parameter number, name
Ethernet parameter #9714 Host 1 directory (The same for hosts 2 to 4)
Subprogram storage destination parameter #8881 Subpro stor D0:dir (The same for devices 1 to 4)
3.8.6 Ethernet Parameter Password

If the Ethernet parameter "Host 1 password" to "Host 4 password" is set, "********" displays regardless of the
password characters set in that data field.
I - 225
3. Setup Screen
3.8 User Parameters
3.8.7 Machine Parameter Password Setting Method

The "High-accuracy parameters" and "High-accuracy axis parameters" contain machine parameters other
than the user parameter. It is possible to reference these machine parameters, however, if a machine tool
builder password is not set, it is not possible to set any data.
Move the cursor to the machine parameters to display a "Input a password." message, and the system waits
for the password to be input. Input the machine tool builder password as required. Once input, the password
remains valid until the power is turned OFF.
Operation method (In the case where the password has not been input even once after turning ON the
power.)
(1) Display the High-accuracy Parameters When the cursor is positioned at the machine
screen. parameters, the "Input a password." message
displays. (System awaits password)
When the ↑, ↓ keys are used to move
the cursor to a position other than the
machine parameters, the awaiting
password status is cleared along with the
message.
(2) Input the machine parameter password "*****" displays at the input area while the password is
and press the INPUT key. being input.
Press the INPUT key to clear the awaiting
password status, and enable machine parameter
settings to be made.
(Note) If the password is input incorrectly, the awaiting password status remains cleared and a "The
password is incorrect." message displays.
I - 226
3. Setup Screen
3.8 User Parameters
3.8.8 Parameter List

3.8.8.1 Process Parameters
<WRK COUNT> (No. of workpieces machined)

# Item Contents Setting range (unit)
8001 WRK COUNT M Set the M code that counts the No. of workpiece 0 to 99
repeated machining.
The No. will not be counted when set to 0.
8002 WRK COUNT The current machining No. is displayed. Set the 0 to 999999
initial value.
8003 WRK COUNT LIMIT Set the maximum No. of workpieces machined. 0 to 999999
A signal is output to PLC when the No. of
machining times is counted to this limit.
<AUTO TLM> (Automatic tool length measurement)

8004 SPEED Set the feedrate during automatic tool length 1 to 1000000 (mm/min)
measurement.
8005 ZONE r Set the distance between the measurement point 0 to 99999.999 (mm)
and deceleration start point.
8006 ZONE d Set the tolerable zone of the measurement point. 0 to 99999.999 (mm)
If the sensor signal turns ON in front of d before the
measurement point‚ or if the signal does not turn
ON after d is passed‚ an alarm will occur.
<AUTO CORNER OVR.> (Automatic corner override)

8007 OVERRIDE Set the override value for automatic corner 0 to 100 (%)
override.
8008 MAX ANGLE Set the max. corner opening angle where 0 to 180 (°)
deceleration should start automatically.
If the angle is larger than this value‚ deceleration
will not start.
8009 DSC. ZONE Set the position where deceleration starts at the 0 to 99999.999 (mm)
corner.
Designate at which length point before the corner
deceleration should start.
<T-TIP OFFSET> (Wear data input)

8010 ABS. MAX. Set the max. value when inputting the tool wear 0 to 99.999 (mm)
(For L system only) compensation amount.
A value exceeding this setting value cannot be set.
Absolute value of the input value is set.
(If a negative value is input, it is treated and set as a
positive value.)
If "0" is input, this parameter will be invalid.
8011 INC. MAX. Set the max. value for when inputting the tool wear 0 to 99.999 (mm)
(For L system only) compensation amount in the incremental mode.
Absolute value of the input value is set.
(If a negative value is input, it is treated and set as a
positive value.)
If "0" is input, this parameter will be invalid.
I - 227
3. Setup Screen
3.8 User Parameters
<C-MODAL> (C axis normal line)

8041 C-rot.R This is valid with normal line control type II. 0.000 to 99999.999
Set the length from the center of the normal line (mm)
control axis to the end of the tool. This is used to
calculate the turning speed at the block joint.
8042 C-ins.R This is valid with normal line control type I. 0.000 to 99999.999
Set the radius of the arc to be automatically (mm)
inserted into the corner during normal line control.

8043 Tool HDL FD OFS Set the length from the tool holder to the tool tip. 0.000 to 99999.999
(mm)
8044 UNIT*10 Set the command increment scale. 0 to 10000 (fold)
• The scale is 1 when 0 is set.
<3-dimensional tool radius compensation>

8071 3-D CMP Set the value of the denominator constants for 0 to 99999.999
(for M system only) 3-dimensional tool radius compensation.
Set the value of p in the following formula.
Vx = i x r/p, Vy = j x r/p, Vz = k x r/p
Vx, Vy, Vz : X, Y, and Z axes or vectors of
horizontal axes
i, j, k : Program command value
r : Offset
p= i2 + j2 + k 2 when the set value is 0.
<Scaling>
8072 SCALING P Set the scale factor for reduction or magnification 0 to 99.999999
(for M system only) for the machining program for which the G50 or
G51 command is issued.
This parameter is effective when the program
specifies no scale factor.
<Spiral interpolation>
8075 SpiralEndErr Designate the tolerable error range (absolute value) 0 to 99999.999 (mm)
(for M system only) when the end point position commanded with the
command format type 2 spiral interpolation or
conical interpolation command differs from the end
point position obtained from the speed and
increment/decrement amount.

8078 Screen Saver Timer When not using, set to "0". 0
I - 228
3. Setup Screen
3.8 User Parameters
<Coord rotation>
8621 Coord rot plane (H) This sets the plane, center coordinates, vector Axis name
components and angle.
Plane (horizontal axis):
8622 Coord rot plane (V) This sets the name of the 1st axis when measuring
the rotation.
When not set, the name will be the X axis.
Plane (vertical axis):
8623 Coord rot centr (H) -999999.999 to
This sets the name of the 2nd axis when
999999.999 (mm)
measuring the rotation.
When not set, the name will be the Y axis.
8624 Coord rot centr (V)
Plane (vertical) Center
coordi-
nates Vector (vertical)
8625 Coord rot vctr (H) Angle
Center coordi-
nates (vertical) Vector (horizontal)
8626 Coord rot vctr (V)
M Plane (horizontal)
Center coordinates
8627 Coord rot angle (horizontal) -360.000 to 360.000
(°)
(Note) The angle is automatically calculated and
enumerated at vector component setting,
but direct setting of the angle is possible.
When directly setting the angle, "0" appears
in both the horizontal axis and vertical axis
of the vector components.
I - 229
3. Setup Screen
3.8 User Parameters
<TLM>
8701 Tool length This sets the length to the touch tool tip. ±99999.999 (mm)
8702 Tool Dia This sets the diameter of the sphere at the touch ±99999.999 (mm)
tool tip.
8703 OFFSET X This sets the deviation amount (X direction) from ±99999.999 (mm)
the touch tool center to the spindle center.
8704 OFFSET Y This sets the deviation amount (Y direction) from ±99999.999 (mm)
the touch tool center to the spindle center.
8705 RETURN This sets the one-time return distance for 0 to 99999.999 (mm)
contacting again.
8706 FEED This sets the feedrate when contacting again. 1 to 60000 (mm/min)
8707 Skip past amout (H) This sets the difference (horizontal axis direction) of ±99999.999 (mm)
the skip read value and actual skip position.
8708 Skip past amout (V) This sets the difference (vertical axis direction) of ±99999.999 (mm)
the skip read value and actual skip position.
8709 EXT work sign rvs This is set when using the external workpiece 0/1
coordinate system with Z shift.
0: External workpiece offset (Z shift) no sign
reversal (Conventional)
1: External workpiece offset (Z shift) sign reversal
8710 EXT work ofs invld This sets whether external workpiece offset 0/1
subtraction is valid when setting the workpiece
coordinate offset.
0: Do not subtract external workpiece offset.
(Conventional)
1: Subtract the external workpiece offset.
8711 TLM L meas axis This designates the tool length measurement axis. Axis name (Note 1)
This sets the #1022 axname2 axis name.
8712 TLM D meas axis This designates the tool diameter measurement Axis name (Note 2)
axis.
This sets the #1022 axname2 axis name.
(Note 1) If the axis name is illegal or not set, the 3rd axis name will be set as a default.
(Note 2) If the axis name is illegal or not set, the 1st axis name will be set as a default.
I - 230
3. Setup Screen
3.8 User Parameters
<Surface speed control>

19425 ManualB Std R1 This sets a radius used as reference for the rotation 0 to 99999.999 (mm)
axis speed.
19426 ManualB Std F1 This sets the rotation axis speed for surface speed 1 to 1000000 (°/min)
control reference radius 1.
19427 ManualB Std R2 This sets a radius used as standard for the rotary 0 to 99999.999 (mm)
axis speed.
When the same value is set as "#19425 ManualB
Std R1", the surface speed control standard speed
1 (ManualB Std F1) will be selected as the rotary
axis speed if the radius is less than that value. The
surface speed control standard speed 2 (ManualB
Std F2) is selected if larger than the set value.
19428 ManualB Std F2 This sets the rotary axis speed for surface speed 1 to 1000000 (°/min)
control standard radius 2 (ManualB Std R2).
(Note) The relation of the parameter settings is as follows.

When #19425 setting > #19427 setting : #19425 setting is used as surface speed control standard
radius 2 (ManualB Std R2). Similarly, #19427 setting is used as surface speed control standard radius
1 (ManualB Std R1).
When #19426 setting > #19428 setting : #19426 setting is used as surface speed control standard
speed 2 (ManualB Std F2). Similarly, #19428 setting is used as surface speed control standard speed
1 (ManualB Std F1).
I - 231
3. Setup Screen
3.8 User Parameters
3.8.8.2 Fixed Cycle

8012 G73 n Set the return amount for G73 (step cycle). 0 to 99999.999 (mm)
(For M system only)
8013 G83 n Set the return amount for G83 (deep hole drilling 0 to 99999.999 (mm)
cycle).
8014 CDZ-VALE Set the screw cut up amount for G76‚ G78 (thread 0 to 127 (0.1 lead)
(For L system only) cutting cycle).
8015 CDZ-ANGLE Set the screw cut up angle for G76‚ G78 (thread 0 to 89 (°)
(For L system only) cutting cycle).
8016 G71 MINIMUM The end of cutting in the rough cutting cycle (G71, 0 to 999.999 (mm)
(For L system only) G72) is the remainder cutting amount. If the amount
is smaller than the value set with this parameter,
the last cycle will not be executed.
8017 G71 DELTA-D The rough cutting cycle (G71, G72) cutting amount 0 to 999.999 (mm)
(For L system only) repeats d+ d, d, d- d using the value (d)
commanded with D as a reference. Set the change
amount d.
8018 G84/G74 n This is not used. Set it to "0". 0
(For M system only)

8051 G71 THICK Set the amount of cut-in by the rough cutting cycle 0 to 99999.999 (mm)
(G71, G72)
8052 G71 PULL UP Set the amount of pull-up when returning to the 0 to 99999.999 (mm)
cutting start point for the rough cutting cycle (G71.
G72).
8053 G73 U Set the X-axis cutting margin of the forming rough -99999.999 to
cutting cycle (G73). 99999.999 (mm)
8054 G73 W Set the Z-axis cutting margin of the forming rough -99999.999 to
cutting cycle (G73). 99999.999 (mm)
8055 G73 R Set the number of times cutting is performed by the 0 to 99999 (times)
forming rough cutting cycle (G73).
8056 G74 RETRACT Set the amount of retract (amount of cut-up) of the 0 to 999.999 (mm)
push-cut cycle (G74, G75).
8057 G76 LAST-D Set the amount of final cut-in by the compound type 0 to 999.999 (mm)
thread cutting cycle (G76).
8058 G76 TIMES Set the number of times the amount of final cut-in 0 to 99 (times)
cycle (G76 finish margin) is divided in the
compound type thread cutting cycle (G76).
8059 G76 ANGLE Set the angle (thread angle) of the tool nose in the 0 to 99 (°)
compound type thread cutting cycle (G76).
<Deep hole drilling cycle>

8083 G83S modeM Set the M command code for changing to the small 1 to 99999999
(for M system only) diameter deep hole drilling cycle mode.
8084 G83S Clearanse Set the clearance amount for the small diameter 0 to 999.999 (mm)
(for M system only) deep hole drilling cycle (G83).
8085 G83S Forward F Set the feedrate from the R point to the cutting start 0 to 99999 (mm/min)
(for M system only) position in the small diameter deep hole drilling
cycle (G83).
8086 G83S Back F Set the speed for returning from the hole base 0 to 99999 (mm/min)
(for M system only) during the small diameter deep hole drilling cycle
(G83).
I - 232
3. Setup Screen
3.8 User Parameters
3.8.8.3 Control Parameters
# Items Details Setting range (unit)

1103 T_life Validate life Select the usage of the tool life management 0/1
management function.
0: Do not manage tool life.
1: Execute tool life management function
control.
1104 T_Com2 Tool Select the command method for when #1103 T_Life 0/1
command is set to 1.
method 2 0: Handle the program tool command as the
group No.
1: Handle the program tool command as the tool
No.
1105 T_Sel2 Tool selection Select the tool selection method for when #1103 0/1
method 2 T_Life is set to 1.
0: Select in order of registered No. from the
tools used in the same group.
1: Select the tool with the longest remaining life
from tools used in the same group and the
unused tools.
1106 Tcount Life Specify the function when address N is omitted 0: Time specified
(For L management when inputting data (G10 L3 command) for tool life input
system count management function ll. 1: No. of times
only)
specified input
I - 233
3. Setup Screen
3.8 User Parameters

8101 MACRO SINGLE Select the control of the blocks where the user 0/1
macro command continues.
0: Do not stop while macro block continues.
1: Stop every block during signal block
operation.
8102 COLL. ALM OFF Select the interference (bite) control to the 0/1
workpiece from the tool diameter during tool radius
compensation and nose R compensation.
0: An alarm is output and operation stops when
an interference is judged.
1: Changes the path to avoid interference.
8103 COLL. CHK OFF Select the interference (bite) control to the 0/1
workpiece from the tool diameter during tool radius
compensation and nose R compensation.
0: Performs interference check.
1: Does not perform interference check.
8105 EDIT LOCK B Select the edit lock for program Nos. 8000 to 9999 0/1
in the memory.
0: Program can be edited.
1: Editing of above program is prohibited. The
file cannot be opened.
8106 G46 NO REV-ERR Select the control for the compensation direction 0/1
(For L system only) reversal in G46 (nose R compensation).
0: An alarm is output and operation stops when
the compensation direction is reversed (G41
→ G42’ G42 → G41).
1: An alarm does not occur when the
compensation direction is reversed’ and the
current compensation direction is maintained.
8107 R COMPENSATION 0: In arc cutting mode, the machine moves to 0/1
the inside because of a delay in servo
response to a command, making the arc
smaller than the command value.
1: In arc cutting mode, the machine
compensates the movement to the inside
because of a delay in servo response to a
command
8108 R COMP Select Select whether to perform arc radius error 0/1
compensation over all axes or axis by axis.
0: Perform compensation over all axes.
1: Perform compensation over axis by axis.
(Note) This parameter is effective only when “#8107
R COMPENSATION” is 1.
8109 HOST LINK Select whether to enable computer link B instead of 0/1
the RS-232C port.
0: Disable computer link B to enable normal
RS-232C communication.
1: Enable computer link B to disable normal
RS-232C communication.
8110 G71/G72 POCKET Set the pocket machining if there is a dimple 0/1
(pocket) in the rough cutting cycle (G71, G72)
finishing program.
0: Pocket machining OFF
1: Pocket machining ON
I - 234
3. Setup Screen
3.8 User Parameters

8111 Milling Radius Select the diameter and radius of the linear axis for 0/1
milling (cylindrical/pole coordinate) interpolation.
0: All axes radius command
1: Each axis setting (follows “#1019 dia”)
(Note) This parameter is valid only in the milling
(cylindrical/pole coordinate) interpolation
mode.
8112 DECIMAL PNT-P 0: The decimal point command for G04 address 0/1
P is invalidated.
1: The decimal point command for G04 address
P is validated.
8113 Milling Init G16 Designate which plane to use for milling machining 0: Plane other than
after the power is turned ON or reset. G16
#8113 #8114 Plane 1: Select G16 plane
0 0 G17 plane
0 1 G19 plane
1 0
G16 plane
8114 Milling Init G19 1 1 0: Plane other than
(Note) This parameter is valid for the G code system G19
2, 3 (“#1037 cmdtyp”=3, 4). 1: Select G19 plane
8116 Coord rot para invd Select the validity of coordinate rotation by the 0/1
parameters.
0: Valid
1: Invalid
8117 OFS Diam DESIGN Select whether tool radius compensation amount is 0/1
designated with tool radius or tool diameter.
0: Tool radius compensation amount
1: Tool diameter compensation amount
8145 Validate F1 digit Specify whether to execute the F command with a 0/1
1-digit code command or with a direct numerical
command.
0: Direct numerical command (command
feedrate during feed per minute or rotation)
1: 1-digit code command (feedrate specified
with #1185 spd_F1 - #1189 F5)
I - 235
3. Setup Screen
3.8 User Parameters
3.8.8.4 Operation Parameters

8901 Counter type 1 This sets the type of counter displayed at the upper 0 to 255
left of the AUTO/MDI display on the Monitor screen. 1: Current position
2: Work coordinate
position
3: Machine position
8902 Counter type 2 This sets the type of counter displayed at the lower
left of the AUTO/MDI display on the Monitor screen. 4: Program position
8: Remain
command
9: Manual interrupt
8903 Counter type 3 This sets the type of counter displayed at the upper amount
right of the AUTO/MDI display on the Monitor
10: Next command
screen.
11: Restart position
12: Remain distance
8904 Counter type 4 This sets the type of counter displayed at the lower 16: Tip work
right of the AUTO/MDI display on the Monitor coordinate
screen. position
18: Tool axis
movement
8905 Counter type 5 This sets the type of counter displayed at the left of
19: Tip machine
the Manual display on the Monitor screen.
position
20: Relative position
8906 Counter type 6 This sets the type of counter displayed at the right
of the Manual display on the Monitor screen.
8910 Edit undo This sets whether to validate the Undo function 0/1
during program edit on the Monitor screen or Edit
screen.
0: Invalid
1: Valid
8914 Auto Top search This sets the operation method for restart search 0/1
type 2.
0: It is necessary to set the top search position
arbitrarily.
1: The restart search is executed from O No.
that is designated as head.
8915 Auto backup day 1 When the NC power is ON after the designated -1 to 31
date was passed over, the automatic backup is (-1 can be set for
8916 Auto backup day 2 executed. "Auto backup day 1"
When -1 is set to "Auto backup day 1", the only.)
8917 Auto backup day 3 automatic backup is executed every turning NC
power ON.
8918 Auto backup day 4 When 0 is set to all on "Auto backup day 1" to "4",
the automatic backup is not executed. It is possible
to specify the designated date up to 4 days for a
month.
I - 236
3. Setup Screen
3.8 User Parameters

8919 Auto backup device This sets the automatic backup target device. 0: DS
1: HD
2: Memory card
8920 3D tool ofs select This designates the method to calculate the drawing 0/1
position when drawing a solid.
With 3D drawing, the drawing position (tool tip
position) is calculated with the method designated
with this parameter, and the image is drawn.
0: Drawing position = Tool center path information
(machine position) - Tool length offset + wear
1: Drawing position = Tool center path information
(machine position) - tool length set on 3D Tool
Setting screen.
8921 Mass Edit select This sets the editing mode for the machining 0/1
programs saved in HD, FD, and memory card.
0: Regular editing mode
If the program size is 1.0MB (When #8910 Edit
Undo is invalid, 2.0MB) or more, mass-editing
will be applied.
1: Mass-editing mode
8922 T-reg-no dup check Set whether to validate the duplication check in 0/1
registering tools to magazine pots, and in setting
tool Nos. for spindle/standby.
0: Duplication check valid
1: Duplication check invalid
I - 237
3. Setup Screen
3.8 User Parameters
3.8.8.5 I/O Parameters

There are basically two types of input/output parameters which must be set when inputting‚ outputting or
referring to data‚ or when performing tape operation.
9001 to 9018 parameters:

Set which channel to connect which device to for each I/O application.

Set the transmission speed, etc., for each input/output device.
Up to five types of input/output device parameters can be set in device 0 to 4.
<I/O> # <PORT No.> # <DEV. No.> <DEV. NAME>

Specify the board No. to which the serial Set the input/output device No. for
input/output device is connected. each application.
• Set "1" to use ch1. The device Nos. are 0 to 4 and
• Set "2" to use ch2. correspond to the input/output
device parameters.
The device name set in the
input/output device parameter is
also displayed for identification.
DATA IN 9001 Specify the port for inputting the data 9002 Specify the device No. that inputs
such as machine program and the data.
parameters.
DATA OUT 9003 Specify the port for outputting the data 9004 Specify the device No. that outputs
such as machine program and the data.
parameters.
TAPE MODE 9005 Specify the input port for running with 9006 Specify the device No. to be run
the tape mode. with the tape mode.
MACRO PRINT 9007 Specify the output port for the user 9008 Specify the device No. for the
macro DPRINT command. DPRINT command.
PLC IN/OUT 9009 Specify the port for inputting/outputting 9010 Specify the device No. for the PLC
various data with PLC. input/output.
REMOTE PRG 9011 Specify the port for inputting remote 9012 Specify the device No. used to
IN programs. input remote programs.
EXT UNIT 9013 Specify the port for communication with 9014 Specify the unit No. used for
an external unit. communication with an external
unit
HANDY 9017 Specify the port for communication with 9018 9018 Specify the device No. used
TERMINAL a handy terminal. for communication with a handy
terminal.
I - 238
3. Setup Screen
3.8 User Parameters

9101 DEV0 Set the device name corresponding to the device Use alphabet
DEVICE NAME No. characters‚ numerals
Set a simple name for quick identification. and symbols to set a
name within 3
characters.
9102 DEV0 Set the serial communication speed. 0: 19200 (bps)
BAUD RATE 1: 9600
2: 4800
3: 2400
4: 1200
5: 600
6: 300
7: 150
9103 DEV0 Set the stop bit length used in the start-stop 1: 1 (bit)
STOP BIT system. 2: 1.5
3: 2
9104 DEV0 Specify whether to add the parity check bit to the 0: Parity bit not added
PARITY CHECK data during communication. 1: Parity bit added
9105 DEV0 Specify the odd or even parity when it is added to 0: Odd parity
EVEN PARITY the data. 1: Even parity
9106 DEV0 Set the length of the data bit. 0: 5 (bit)
CHR. LENGTH 1: 6
2: 7
3: 8
9107 DEV0 The code to terminate data reading can be 0 and 3: EOR
TERMINATR TYP selected. 1 and 2: EOB or EOR
9108 DEV0 Specify the transmission control method. 1: RTS/CTS method
HAND SHAKE The method will be no procedure if a value except 1 2: No procedure (No
to 3 is set. handshaking)
3: DC code method
9109 DEV0 Specify the DC code when the DC code method is 0: No parity to DC
DC CODE PRTY selected. code (DC3 = 13H)
1: DC code with parity
(DC3 = 93H)
9111 DEV0 Specify the DC code handling when outputting data DC2 / DC4
DC2/4 OUTPUT to the output device. 0: None / None
1: Yes / None
2: None / Yes
3: Yes / Yes
9112 DEV0 Specify whether to insert the (CR) code just before 0: Do not add
CR OUTPUT the EOB (L/F) code during output. 1: Add
9113 DEV0 In data output mode, select the ISO or EIA code for 0: ISO code output
EIA OUTPUT data output. 1: EIA code output
In data input mode, the ISO and EIA codes are
identified automatically.
9114 DEV0 Specify the length of the tape feed to be output at 0 to 999 (characters)
FEED CHR. the start and end of the data during tape output.
I - 239
3. Setup Screen
3.8 User Parameters

9115 DEV0 Specify whether to check the parity of the No. of 0: Do not perform
PARITY V characters in block during data input. parity V check
The No. of characters is factory-set so that the 1: Perform parity V
check is valid at all times. check
9116 DEV0 Set the time out time to detect an interruption in 0 to 30 (s)
TIME-OUT (sec) communication.
Time out check will not be executed when set to 0
to 30 seconds.
9117 DEV0 Specify whether to check the DR data at the data 0: DR valid
DR OFF input/output. 1: DR invalid
9118 DEV0 0: Output in ISO/EIA code (Depends on whether 0/1
DATA ASCII #9113, #9213, #9313, #9413, or #9513 EIA
output parameter is set up)
1: Output in ASC II code
9119 DEV0 Specify the mode for input (collation). 0/1
INPUT TYPE 0: Standard input (Data from the very first EOB is
handled as significant information.)
1: EOBs following the first EOB of the input data
are skipped until data other than EOB is input.
DEV0 When output with EIA code‚ data can be output 0 to FF (hexadecimal)
9121 EIA CODE [ using the alternate code in which the special ISO
9122 ] code not included in EIA is specified.
9123 # Specify the codes which do not duplicate the
9124 existing EIA codes by hexadecimal for respective
∗
9125 special codes.
=
9126
:
9127
$
9128
!
9201 to Set the same settings for device 1.

I - 240
3. Setup Screen
3.8 User Parameters
3.8.8.6 Ethernet Parameters

Set the parameters related to Ethernet input/output.
After setting up the parameter (PR) listed in the table, turn OFF the NC power. To validate the parameter, turn
ON the power again.

When several TCP/IP drivers are installed and the IP address is set manually ("#9701 IP address
automatic setting" is set to 0), the same setting will be made for all parameters.

Set the server information required for using the Ethernet function.
Server information for up to four units can be set.

9701 IP addr auto set The IP address is automatically assigned from the 0: Manual setting
(PR) DHCP server. 1: Automatic setting
(Note) When this setting is validated, the following
parameters "#9702 IP address", "#9703
Sub-net address" and "#9704 Gateway
setting" will be invalid.
9702 IP address Set the IP address. 15 characters or less
(PR) This sets the IP address of the TCP/IP assigned to Dot notation numeric
the NC (Windows) computer. Contact the network value train
controller for the address to be set.
(Note) This setting is valid only for 700 Series.
9703 Subnet mask This sets the subnet mask of the TCP/IP assigned 15 characters or less
(PR) to the NC (Windows) computer. Contact the Dot notation numeric
network controller for the subnet mask to be set. value train
(Note) This setting is valid only for 700 Series.
9704 Gateway This sets the gateway of the TCP/IP assigned to the 15 characters or less
(PR) NC (Windows) computer. Dot notation numeric
(Note) This setting is valid only for 700 Series. value train
9705 Timeout This sets the timeout time (s) for when the 10 to 99 (s)
communication is not completed correctly, or when (Standard: 30)
there is no communication response.
9706 Host No. This selects the number of the host to be used from 1 to 4 : Host No.
host 1 to host 4.
9711 Host1 host name This sets the host computer name. 15 characters
This parameter allows the NC to easily recognize (alphanumeric) or less
the host computer on the network. Set the host
computer's name (name registered in
C:¥windows¥hosts) or the IP address.
<Setting example>
For host name : Mspc160
For IP address : 150.40.0.111
(Note) Set the host computer's TCP/IP address if
communication is not carried out correctly.
9712 Host1 user name This sets the user name when logging into the host 15 characters
computer. (alphanumeric) or less
9713 Host1 password This sets the password when logging into the host 15 characters
computer. (alphanumeric) or less
9714 Host1 directory This sets the directory name of the host computer. 31 characters
Refer to (Note 4) for details. (alphanumeric) or less
I - 241
3. Setup Screen
3.8 User Parameters

9715 Host1 host type This sets the type of host computer. 0: UNIX/PC automatic
(Note) When "0" is set, the settings for the judgment
following parameters will be invalid. 1: UNIX
• Wrd pos: name 2: PC (DOS)
• Wrd pos: size
• Wrd pos: Dir
• Wrd pos: cmnt
• Wrd num: cmnt
9716 Host 1 This sets the file name display position (nth word 0 to 100
Wrd pos: name from left) of the list displayed when the ftp 0: Default value
command "dir" is executed.
(Note) One word designates a character string
divided by one or more spaces.
9717 Host 1 This sets the size display position (nth word from 0 to 100
Wrd pos: size left) of the list displayed when the ftp command "dir" 0: Default value
is executed.
9718 Host 1 This sets the <DIR> display position (nth word from 0 to 100
Wrd pos: Dir left) of the list displayed when the ftp command "dir" 0: Default value
is executed.
9719 Host 1 This sets the comment (date, time, etc.) display 0 to 100
Wrd pos: cmnt position (nth word from left) of the list displayed 0: Default value
when the ftp command "dir" is executed.
9720 Host 1 This sets the number of words to be displayed as a 0 to 100
Wrd num: cmnt comment. 0: Default value
9721 Host 1 This sets whether to display the total number of 0: Display
no total siz characters registered in the machining programs of 1: Do not display
host1 when displaying the file list.
If there are many files in the directory to be referred
to, the list can be updated quickly by setting "1".
9731 Host 2 parameters Set the same settings for host 1.

to
9741
to
9761
to
9781
(Note 1) The user name and password are required when logging in.
(Note 2) It is necessary to enable reading/writing when exchanging files.
(Note 3) With the Personal WEB Server and Windows NT 4.0 fpt Server, the file list format can be selected
from DOS or UNIX.
(Note 4) The directory released to the client (NC unit) with the host computer's server is handled as the root
directory by the NC unit.
I - 242
3. Setup Screen
3.8 User Parameters
3.8.8.7 Computer Link Parameters

9601 BAUD RATE Specify the rate at which data is transferred. 0: 19200 (bps)
1: 9600
2: 4800
3: 2400
4: 1200
5: 600
6: 300
7: 110
8: 38400
9602 STOP BIT Specify stop bit length used in start-stop mode. 1: 1
See "PARITY EFFECTIVE" in #9603. The 2: 1.5
number of characters is adjusted in output mode so 3: 2
that no problems occur if the parity check is
enabled.
9603 PARITY EFFECTIVE This parameter is set when using a parity bit 0: No parity bit used in
separately from the data bit. I/O mode
1 character 1: Parity bit used in I/O
ON mode
OFF b1 b2 b3 b4 b5 b6 bn
Start bit Data bit Parity bit Stop bit

Set this to match the input/output device
specifications.
9604 EVEN PARITY Specify whether even or odd parity is used when 0: Odd parity
parity is used. This parameter is ignored when no 1: Even parity
parity is used.
9605 CHR. LENGTH Specify data bit length. 0: 5
See "PARITY EFFECTIVE" in #9603. 1: 6
2: 7 (NC connection
not supported)
3: 8
9606 HAND SHAKE Select RS-232C transmission control mode."3" (DC 0: No control
control mode) should be set for computer link B. 1: RTS/CTS method
2: No handshaking
3: DC control mode
9607 TIME-OUT SET Specify time-out time at which an interruption of 0 to 999 (1/10s)
data transfer during data input/output should be
detected.
If 0 is set, time infinity is specified.
9608 DATA CODE Specify the code to be used. 0: ASCII code
See "PARITY EFFECTIVE" in #9603. 1: ISO code
9609 LINK PARAM. 1 Bit 1: DC1 output after NAK or SYN 0: Don't output the
Specify whether to output the DC1 code after DC1 code.
the NAK or SYN code is output. 1: Output the DC1
code.
Bit 7: Enable/disable resetting 0: Enable resetting.
Specify whether to enable resetting in the 1: Disable resetting.
computer link.
I - 243
3. Setup Screen
3.8 User Parameters

9610 LINK PARAM. 2 Bit 2: Specify the control code parity (even parity 0: No control code
for the control code). parity added
Set the parity in accordance with the I/O device 1: Control code parity
specifications. added
Bit 3: Parity V 0: Disable
Specify whether to enable checking of parity 1: Enable
V in one block in data input mode.
9611 LINK PARAM. 3 Not used
9614 START CODE Specify the code by which file data transfer begins 0: DC1 (11H)
at first. 1: BEL (07H)
This parameter is used for a specific user, and set 0
in this parameter for normal operation.
9615 CTRL. CODE OUT Bit 0: NAK output 0: Do not output the
Specify whether to send the NAK code to the NAK code.
host if a communication error occurs in 1: Output the NAK
computer link B. code.
Bit 1: SYN output 0: Do not output the
Specify whether to send the SYN code to the SYN code.
host if NC resetting or an emergency stop 1: Output the SYN
occurs in computer link B. code.
Bit 3: DC3 output 0: Do not output the
Specify whether to send the DC3 code to the DC3 code.
host when communication ends in computer link 1: Output the DC3
B. code.
9616 CTRL. INTERVAL Not used
9617 WAIT TIME Not used
9618 PACKET LENGTH Not used
9619 BUFFER SIZE Not used
9620 START SIZE Not used
9621 DC1 OUT SIZE Not used
9622 POLLING TIMER Not used
9623 TRANS. WAIT TMR Not used
9624 RETRY COUNTER Not used
I - 244
3. Setup Screen
3.8 User Parameters
3.8.8.8 Subprogram Storage Destination Parameters

8880 Subpro stor D0: dev If D1 to D4 is designated when calling the Device name (Note 3)
subprogram, the subprogram to be called will be
searched from the storage destination (device and
8881 Subpro stor D0: dir directory) designated with this parameter. Directory 48
(Example) characters
The following will be searched:
8882 Subpro stor D1: dev M98 P (program No.), D0 Device name (Note 3)
Device : "330043 Subpro stor D0:dev"
device
8883 Subpro stor D1: dir Directory : "330044 Subpro stor D0:dir" Directory 48
directory characters
(Note 1) If the called subprogram is not found in
8884 Subpro stor D2: dev the designated storage destination, a Device name (Note 3)
program error will occur.
(Note 2) If D0 to D4 is not designated when the
subprogram is called, the subprogram
8885 Subpro stor D2: dir Directory 48
will be searched from the memory.
characters
(Note 3) The following values are set in the device
name.
8886 Subpro stor D3: dev Device name (Note 3)
Setting value Display name
M Memory
8887 Subpro stor D3: dir G HD Directory 48
characters
F FD
R Memory card
8888 Subpro stor D4: dev Device name (Note 3)
D Data server
E Ethernet
8889 Subpro stor D4: dir Directory 48
characters
I - 245
3. Setup Screen
3.8 User Parameters
3.8.8.9 Axis Parameters

Set up the parameter required for each axis.

8201 AX. RELEASE Select the function to remove the control axis from 0/1
the control target.
0: Control as normal.
1: Remove from control target.
8202 OT-CHECK OFF Select the stored stroke limit II function set in #8204 0/1
and #8205.
0: Stored stroke limit II valid
1: Stored stroke limit II invalid
8203 OT-CHECK-CANCEL When the simple absolute position method (#2049 0/1
type is 9) is selected, the stored stroke limits I, II (or
IIB) and IB will be invalid until the first reference
position return is executed after the power is turned
ON.
0: Valid (according to #8202)
1: Temporary cancel
(Note) “#8203 OT-CHECK-CANCEL” affects all the
stored stroke limits.
8204 OT-CHECK-N This sets the coordinates of the (-) direction in the ±99999.999 (mm)
moveable range of the stored stroke limit II or the
lower limit coordinates of the prohibited range of
stored stroke limit IIB.
If the sign and value are the same as #8205, the
stored stroke limit II (or IIB) will be invalid.
If the stored stroke limit IIB function is selected, the
prohibited range will be between two points even
when #8204 and #8205 are set in reverse.
When II is selected, the entire range will be
prohibited if #8204 and #8205 are set in reverse.
8205 OT-CHECK-P This sets the coordinates of the (+) direction in the ±99999.999 (mm)
moveable range of the stored stroke limit II or the
upper limit coordinates of the prohibited range of
stored stroke limit IIB.
8206 TOOL CHG. P Set the coordinates of the tool change position for ±99999.999 (mm)
G30. n (tool change position return).
Set with coordinates in the basic machine
coordinate system.
8207 G76/87 IGNR Select the shift operation at G76 (fine boring) and 0/1
(For M system only) G87 (back boring).
0: Shift effective
1: No shift
8208 G76/87 (-) Specifies the shift direction at G76 and G87. 0/1
(For M system only) 0: Shift to (+) direction
1: Shift to (-) direction
8209 G60 SHIFT Set the last positioning direction and distance for a ±99999.999 (mm)
(For M system only) G60 (unidirectional positioning) command.
8210 OT INSIDE The stored stoke limit function to be set in #8204 0/1
and #8205 prevents the machine from moving to
the inside or outside of the specified range.
0: Inhibits outside area
(Select stored stroke limit II.)
1: Inhibits inside area
(Select stored stroke limit II B.)
I - 246
3. Setup Screen
3.8 User Parameters

8211 MIRR. IMAGE Enable or disable the parameter mirror image 0/1
function.
0: Disable
1: Enable
8213 Rotation axis type This designates the rotation type (short-cut 0: Short-cut invalid
(PR) valid/invalid) or linear type (workpiece coordinate 1: Short-cut valid
linear type/all coordinate linear type). 2: Workpiece
This parameter is valid only when „#1017 rot“ is set coordinate linear
to 1. (Note) type
3: All coordinate
linear type
8215 TLM standard length This sets the TLM standard length. -99999.999 to
TLM standard length is the distance from a tool 99999.999 (mm)
replacement point (reference position) to the
measurement basic point (surface) which is used to
measure the tool length.
8216 Type in G28 return Define the performance after establishing the 0/1
reference position in automatic reference position
return command when the reference position has
not been established with the distance-coded
reference position detection.
0: Move to reference position
1: Won't move to reference position
8217 Check start point Set up a drawing start position in graphic check of -99999.999 to
each axis. 99999.999 (mm)
(Note) The movement method is as follows by the specified rotation axis type.
Setting value 0 1 2 3
Workpiece Display range: 0° to 359.999° Display range: 0° to ±99999.999°
coordinate value
Machine Display range: 0° to 359.999° Display range: 0°
coordinate to ±99999.999°
value/relative
position
ABS command The incremental Moves with a In the same manner as the normal
amount from the short-cut to the linear axis, moves according to the
end point to the end point. sign by the amount obtained by
current position is subtracting the current position from
divided by 360, the end point.
and the axis
moves by the
remainder
amount
according to the
sign.
INC command Moves in the direction of the commanded sign by the commanded incremental
amount starting at the current position.
Reference The movement to the middle point applies to the ABS command or the INC
position return command.
Returns with movement within 360 degrees from the Moves and returns
middle point to reference position. in the reference
position direction
for the difference
from the current
position to the
reference position.
I - 247
3. Setup Screen
3.8 User Parameters
3.8.8.10 Barrier Data (For L system only)

8300 P0 Set the reference X-coordinates of the chuck and ±99999.999 (mm)
the tail stock barrier.
Set the center coordinate (radius value) of
workpiece by the basic machine coordinate
system.
8301 P1 Set the area of the chuck and tail stock barrier. ±99999.999 (mm)
8302 P2 Set the coordinate from the center of workpiece for
8303 P3 X-axis. (radius value)
8304 P4 Set the coordinate value by basic machine
coordinate system for Z-axis.
8305 P5
8306 P6
8311 P7 Set the area of the left spindle section. ±99999.999 (mm)
• X axis: Set the coordinate from the workpiece
8312 P8 center (P0). (radius value)
• Z axis: Set the coordinates in the basic
machine coordinate system.
8313 P9 Set the area of the right spindle section. ±99999.999 (mm)
• X axis: Set the coordinate from the workpiece
8314 P10 center (P0). (radius value)
• Z axis: Set the coordinates in the basic
machine coordinate system.
8310 Barrier ON Select the validity of the chuck and tailstock barrier. 0/1
0: Invalid (Setting from special display unit valid)
1: Valid
8315 Barrier Type (L) Set the shape of the left chuck and tailstock barrier. 0/1/2
0: No area
1: Chuck
2: Tailstock
8316 Barrier Type (R) Set the shape of the right chuck and tailstock 0/1/2
barrier.
0: No area
1: Chuck
2: Tailstock
8317 ELIV. AX. Name When the right chuck and tailstock barrier is A/B/.. : (axis
movable, set the name of the delivery axis. address)
When using the multi-part system method and the 1A/1B/..
delivery axis is an axis in the other part system, 2A/2B/.. : (part system
designate the axis including the part system as 1A, designation)
1B or 2A, 2B. If the part system is not designated 0 : cancel
as A and B, the set part system will be used.
8318 Stock Angle (L) Set the angle for the left tailstock end section. 0 to 180 (°)
The angle will be interpreted as 90° if there is no 0: 90° default
setting (when 0 is set).
8319 Stock Angle (R) Set the angle for the right tailstock end section. 0 to 180 (°)
The angle will be interpreted as 90° if there is no 0: 90° default
setting (when 0 is set).
I - 248
3. Setup Screen
3.8 User Parameters
3.8.8.11 High Accuracy Parameters
After setting up the parameter (PR) listed in the table, turn OFF the NC power. To validate the parameter, turn
ON the power again.

1149 cireft Arc Specify whether to enable deceleration at the arc 0/1
deceleration entrance or exit.
speed 0: Disable
change 1: Enable
1205 G0bdcc Acceleration 0: G00 acceleration and deceleration are selected 0/1
and as those after interpolation.
deceleration 1: The G00 acceleration/deceleration is the
before G0
acceleration/decelerate before interpolation
interpolation
regardless of whether the mode is the high
accuracy control mode.
(Note) "1" cannot be set for the 2nd system
onwards.
1206 G1bF Maximum Set up a cutting feedrate when selecting 1 to 999999 (mm/min)
speed acceleration and deceleration before interpolation.
1207 G1btL Time Set up a cutting feed time constant when selecting 1 to 5000 (ms)
constant acceleration and deceleration before interpolation.
Speed
G1bF
G1btL Time
1209 cirdcc Arc Specify the deceleration speed at the arc entrance 1 to 999999 (mm/min)
deceleration or exit.
speed
1568 SfiltG1 G01 software This is a filter time constant used to smoothen 0 to 200 (ms)
acceleration/ changes in the acceleration speed for the cutting
deceleration feed acceleration/deceleration speed when
speed filter accelerating/decelerating before interpolation.
1569 SfiltG0 G00 software This is a filter time constant used to smoothen 0 to 200 (ms)
acceleration/ changes in the acceleration speed for the rapid
deceleration traverse acceleration/deceleration speed when
speed filter accelerating/decelerating before interpolation.
1570 Sfilt2 Software This is a filter time constant used to further 0 to 50 (ms)
acceleration/ smoothen changes in the acceleration speed when
deceleration accelerating/decelerating before interpolation.
speed filter 2 When setting "0" or "1", this parameter is invalid.
1571 SSSdis SSS control The shape recognition range for SSS control is 0/1
adjustment fixed.
coefficient
fixed value
selection
I - 249
3. Setup Screen
3.8 User Parameters

8019 R COMP Set up a compensation coefficient for reducing a 0 to 99 (%)
control error in the reduction of a corner roundness
and arch radius.
The larger the setup value, the smaller the
theoretical error will be. However, since the speed
at the corner goes down, the cycle time is
extended.
Coefficient = 100 - setting value
(Note) This is valid when "#8021 COMP CHANGE"
is set to "0".
Theor R decrease The value calculated with the following data is
displayed for the theoretical radius reduction error
amount ∆R (mm).
∆R is the value when the high accuracy control
mode is valid.
This data is calculated using the following
parameters.
• #2203 SV003(PGN1)
(Position loop gain 1st axis (1/s))
• #2010 fwd_g
(Feed forward gain 1st axis (%))
• #1570 Sfilt2
(Soft acceleration/deceleration filter 2)
• #8019 R COMP
(When "#8021 COMP_CHANGE" is "0".)
• #8023 CURVE COMP
(When "#8021 COMP_CHANGE" is "1".)
Path after soft Command path
acceleration/ Δra ΔR
deceleration 2
F
Path after Δrs

servo control
Theoretical radius reduction amount at arc center

8020 DCC. ANGLE Set up the minimum value of an angle (external 0 to 89 (degrees)
angle) that should be assumed to be a corner. 0: The angle will be
When an inter-block angle (external angle) in high- 5°.
accuracy mode is larger than the set value, it is
determined as a corner and the speed goes down
to sharpen the edge.
θ If the set value is smaller than

θ, the speed goes down to
optimize the corner.
(Note) If "0" is set, it will be handled as 5 degrees.
I - 250
3. Setup Screen
3.8 User Parameters

8021 COMP_CHANGE Select whether to share or separate the 0/1
compensation coefficient at the corner/curve during
the high-accuracy control mode.
0: Share ("#8019 R COMP" is applied.)
1: Separate
• Corner : #8022 CORNER COMP
• Curve : #8023 CURVE COMP
(Note) Set "1" when using SSS control.
8022 CORNER COMP Set the compensation coefficient to further reduce -1000 to 99 (%)
or increase the roundness at the corner during the
high-accuracy control mode.
is set to "1".
8023 CURVE COMP Set the compensation coefficient to further reduce -1000 to 99 (%)
or increase the radius reduction amount at the
curve (arc, involute, spline) during the
is set to "1".
Theor R decrease Refer to "Theor R decrease" for "#8019 R COMP".
I - 251
3. Setup Screen
3.8 User Parameters
<High-accuracy spline>
8025 SPLINE ON Specify whether to enable the spline function. 0/1
(for M system only) 0: Disable the spline function.
1: Enable the spline function.
Spline interpolation will be valid during G61.2
modal regardless of this setting.
8026 CANCEL ANG. When the angle made by blocks exceeds the set 0 to 180 (°)
(for M system only) value, spline interpolation is canceled temporarily. 0: 180 (°)
In consideration of the pick feed, set a value a little
smaller than the pick feed angle.
8027 Toler-1 Specify the maximum chord error (tolerance) in a 0.000 to 100.000 (mm)
(for M system only) block that includes an inflection point. Set the
tolerance applicable when the applicable block is
developed to fine segments by CAM. (normally
about 10 μm)
When 0.000 is set, the applicable block is linear.
8028 Toler-2 Specify the maximum chord error (tolerance) in a 0.000 to 100.000 (mm)
(for M system only) block that includes no inflection point. Set the
tolerance applicable when the applicable block is
developed to fine segments by CAM. (normally
about 10 μm)
When 0.000 is set, the applicable block is linear.
8029 FairingL Set the length of the block subject to fairing. 0 to 100.000 (mm)
(for M system only) (Valid when "#8033 Fairing ON" is set to 1.)
8030 MINUTE LENGS When the length of one block exceeds the set -1 to 127 (mm)
(for M system only) value, spline interpolation is canceled temporarily 0: 1 (mm)
and linear interpolation is performed. Set a value
a little smaller than one block length of the program.
If - 1 is set, spline interpolation is performed
regardless of block length.
<Fairing>
8033 Fairing ON Set whether to use the fairing function. 0/1
(for M system only) 0: Fairing invalid
1: Fairing valid
Fairing function will be valid during G61.2 modal
regardless of this setting.
8034 AccClamp ON Set the method for clamping the cutting speed. 0/1
(for M system only) 0: Clamp with parameter "#2002 clamp" or the
corner deceleration function.
1: Clamp the cutting speed with acceleration
judgment.
(Valid when "#8033 Fairing ON" is set to 1.)
8036 CordecJudge Change the conditions for judging a corner. 0/1
(for M system only) 0: Judge the corner from the angle of the
neighboring block.
1: Judge the corner from the angle of the
neighboring block, excluding minute blocks.
(Valid when "#8033 Fairing ON" is set to 1.)
8037 CorJudgeL Set the length of the block to be excluded. 0 to 99999.999 (mm)
(for M system only) (Valid when "#8036 CordecJudge" is set to 1.)
I - 252
3. Setup Screen
3.8 User Parameters
<SSS control>
8090 SSS ON Set whether to validate SSS control with G05 0/1
(for M system only) P10000.
0: Invalid
1: Valid
8091 StdLength Adjust the maximum value of the range for 0 to 100.000 (mm)
(for M system only) recognizing the shape.
To eliminate the effect of steps or errors, etc., set a
large value. To enable sufficient deceleration, set a
small value.
If "0.000" is set, the standard value (1.000mm) will
be applied.
8092 ClampCoeff Adjust the clamp speed at the curved section 1 to 100
(for M system only) configured of fine segments.
Coefficient = setting value
8093 StepLeng Set the width of the step at which the speed is not -0.001 to 0.100 (mm)
(for M system only) to be decelerated. (Approximately the same as the
CAM path difference [Tolerance].)
If 0 is set, the standard value (5µm) will be applied.
If a minus value is set, the speed will decelerate at
all minute steps.
8094 DccWaitAdd Set the time to wait for deceleration when the 0 to 100 (ms)
(for M system only) speed FB does not drop to the clamp speed.
I - 253
3. Setup Screen
3.8 User Parameters
3.8.8.12 High-accuracy Axis Parameters

2001 rapid Rapid Set up the rapid traverse feedrate for each axis. 1 to 1000000
traverse rate The maximum value to be set differs with (mm/min)
mechanical systems.
2002 clamp Cutting Set the maximum cutting feedrate for each axis. 1 to 1000000
feedrate for Even if the feedrate in G01 exceeds this value‚ the (mm/min)
clamp clamp will be applied at this feedrate.
function
2010 fwd_g Feed forward Set up a feed forward gain for pre-interpolation 0 to 200 (%)
gain acceleration and deceleration.
The larger the set value, the smaller the
theoretical control error will be. However, if a
mechanical vibration occurs, the set value must
be reduced.
2068 G0fwdg G00 feed Specify the feed forward gain applicable to 0 to 200 (%)
forward gain acceleration/deceleration before G00
interpolation.
The greater the set value, the shorter the
positioning time during in-position checking.
If machine vibration occurs, decrease the set
value.
2096 crncsp Minimum Set the minimum clamp speed for corner 0 to 1000000
corner deceleration during the high-accuracy control (mm/min)
deceleration mode. Normally set "0".
speed (Note) This parameter is invalid during SSS
control.
2109 Rapid Rapid Set the rapid traverse rate for each axis during 0 to 1000000
(H-pre- traverse rate high-accuracy control mode. (mm/min)
cision) during high- When "0" is set, "#2001 rapid" is valid.
accuracy
control mode
2110 Clamp Cutting feed Define the maximum cutting feed rate for each 0 to 1000000
(H-pre- rate during axis during high-accuracy control mode. (mm/min)
cision) high- When "0" is set, "#2002 clamp" is valid.
accuracy
control mode
for clamp
function
I - 254
3. Setup Screen
3.9 MDI Program Editing
3.9 MDI Program Editing
Press the main menu [MDI] key to display the contents of the MDI program in a pop-up window.
When the parameter “#1144 mdlkof” is “0” (MDI setting impossible), switch to the MDI mode once to press the
menu “MDI”.
Refer to "4.2 Program Editing" for further details.
I - 255
3. Setup Screen
3.10 Counter Setting
3.10 Counter Setting
This function is used to display the relative position counter in a pop-up window and set the counter.
Function : Used to set an arbitrary value in the relative position counter.
Counter display change : The set data displays only at the relative position counter.
Offset : There is no change.
Refer to "2.11 Counter Setting" for further details.
I - 256
3. Setup Screen
3.11 Manual Numerical Value Commands
3.11 Manual Numerical Value Commands
This function is used to set and display all the Spindle function (S), Miscellaneous function (M), Tool function
(T), and No. 2 miscellaneous function (B) commands.
Input the address for S, M, T, and B to set and display the manual numerical value commands.
Refer to "2.13 Manual Numerical Value Commands" for further details.
I - 257
3. Setup Screen
3.12 T Code List
3.12 T Code List
This function searches the T code in designated machining program (including the subprograms) and lists it
in the order the T codes are commanded. (Max. 100 codes)
As for the T code of the tool that has not been registered, it is indicated with text color and background color
changed.
This window is displayed only when the graphic check option is provided.
(1)
(2)
Display items

(1) T code T codes are listed in the order that the T code is commanded in the designated
machining program (including subprogram). As for the T code of the tool that has not
been registered, it is indicated with text color and background color changed.
(2) Program No. This shows designated program No.
When the number of characters exceeds 15, the excess is indicated as “*”.
Menus (T code list display window)

T-list This displays T code list search window. C
search This menu is invalid while getting the T codes.
This interrupts getting the T codes. C
Halt This menu is valid only while getting the T codes.
Close
I - 258
3. Setup Screen
3.12 T Code List
Menus (T code list search window)

This selects the device for searching for the program to get T codes. C
Memory When a device with directory is selected, the root directory is selected
first.
(In 70 series, only "Memory" and "Memory card" are displayed.) C
HD
Memory C
card
C
DS
C
FD
Sort This changes the method that the list is sorted. C 2.2.3 Changing the
This changes whether to show or hide the comment field in the list. B 2.2.2 Changing Whether
Comment
nondisp
Comment Field
This closes the pop-up window and starts getting T codes. C
Retn
Operation method (Display the T code list)
(1) Press the menu T-list . The menu appears.

The T code list created last appears as a pop-up
window. The Halt menu becomes invalid.
(2) Press the menu T-list search . The submenu appears. The list to select a file appears
as a pop-up window.
(3) Select the device. The selected device name and its root directory (HD:/)
[EX.] HD appears in the directory display area.
Use the ↑ , ↓ , ½ , ¾ keys T code list appears as a pop-up window.

(4) to align the cursor with the directory of Getting T code and listing starts.
target machining program, and press The Halt menu becomes valid.
INPUT . The T-list search is invalid.
T code list cannot be displayed when INPUT key is pressed with the following programs selected;
• The program that does not exist.
• The program that is waiting to be restarted.
• The program during automatic operation.
• The program being checked.
The list window will not change.
(Note 1) When switching to the other screen, getting T code is interrupted automatically.
(Note 2) When the Close menu is pressed, getting T code is interrupted automatically.
(Note 3) T code list for MDI program cannot be displayed.
(Note 4) T code list acquisition is not possible for a program with 33 or more program name characters.
I - 259
3. Setup Screen
3.13 Pallet Program Registration [700 series only]
Machining programs can be registered per each pallet of the automatic pallet changer (hereinafter APC) and
the indexing plane.
The Pallet Program Registration screens include "Standard Pallet Registration screen" and "Pallet 4 Page
Registration screen", and those two screens can be switched by the parameters.
Screen Function
Standard Pallet Registration screen Registration of machining programs for pallet 1 & 2 is carried out.
Pallet 1 & 2 can be registered at once.
Pallet 4 Page Pallet list Machining program device, file name, machining status, and index
Registration screen planes under machining for 4 planes of the pallet 1 to 12 are
screen displayed.
Information of 2 pallets can be displayed at once.
Pallet details Machining program device, file name, machining status, and
screen external workpiece coordinates for each plane of the pallet 1 to 12
are set.
Information of one pallet's 2 indexing planes can be set at once.
(Note) The number of pallets is determined by the parameter "#11002 Valid pallet num".
#11001 APC type Screen
0 Standard Pallet Registration

1 Pallet 4 Page Registration
I - 260
3. Setup Screen
3.13.1 Standard Pallet Registration
(1)
(6)
(2)
(3)
(4)
(5)
Display items

(1) Program Dev./Name The machining program device and file name registered for each pallet are displayed.
(2) Machining The ON/OFF state of machining for each pallet is displayed.
ON/OFF
(3) Aux. If there are any auxiliary functions, the auxiliary function data for each pallet is
displayed.
Refer to the Instruction Manual issued by the machine tool builder for details on the
corresponding functions.
(4) Program Search The ON/OFF state of search for the registered machining program is displayed.
ON/OFF
(5) Program Start The ON/OFF state of continuous start for the registered machining program is
ON/OFF displayed.
When set to ON, the searched program will be started for the pallet in the machine.
This setting is valid only when Pallet Program Search is set to ON.
(6) Machined "Machined" is displayed for the pallet in the machine.
I - 261
3. Setup Screen
Menus

Device menu is displayed. C Registering a machining
Device
select If selected, the device name of the pallet currently indicated by the program for the pallet
cursor is changed.
File The file name to be registered can be selected from the list. C Selecting a file name
set A list of files of the currently selected device is displayed. from the list
This menu can be used only when the cursor is at file name.
The state (Machining, Program Search, Program Start) indicated by C Registering a machining
ON the cursor is validated. program for the pallet
This menu can be used only when the cursor is at Machining,
Program Search, or Program Start.
The state (Machining, Program Search, Program Start) indicated by C
OFF the cursor is invalidated.
Operation method (Registering a machining program for the pallet)
(1) Using the , , , keys,

move the cursor to the area of the pallet
for which a program is to be registered.
(2) Press the Device select menu and The cursor is moved to "Device". The device menu
select a device. (Memory, HD, DS, FD, Memory card) is displayed. If
selected, the device selected in "Device" is displayed.
(3) Move the cursor to "File name" and input The contents set in "File name" is displayed.
the program No.
Move the cursor to "Machining" and press The contents set in "Machining" is displayed.
(4) the ON or OFF menu.
(5) Move the cursor to "Program Search" and The contents set in "Program Search" is displayed.
press the ON or OFF menu.
(6) Move the cursor to "Program Start" and The contents set in "Program Start" is displayed.
Operation method (Selecting a file from the list)
(1) Move the cursor to "File name" and press A list of files for the specified device is displayed.
the File set menu.
(2) Move the cursor to an arbitrary file and The selected file name is displayed in "File name". The
press the INPUT key. cursor is moved to "Machining". An arbitrary file name
can be directly entered, as well.
(Note 1) When a file name is directly entered, whether or not the file exists is not checked.
(Note 2) When a file name is directly entered, if other than character strings or values within the setting
range (1 to 99,999,999) is set, an error occurs.
(Note 3) If a directory is specified, a setting error occurs.
I - 262
3. Setup Screen
3.13.2 Pallet List Screen
Machining program device, file name, machining status, and index planes under machining for 4 planes of
the pallet 1 to 12 are displayed.
(1)
(2)
(6)
(3)
(4)
(5)
Display items

(1) Dev./File name Machining program device name and file name to be registered in each pallet's index
plane are displayed.
(2) Machining ON/OFF Whether machining for each pallet's index plane is valid or invalid is displayed.
(3) Machining index plane 0°, 90°, 180°, 270° are displayed.
An asterisk (*) is displayed with the angle of the index plane.
(4) Program Search ON/OFF Whether search for the registered machining program is valid or invalid is displayed.
When valid, the next program registered will be searched automatically as soon as
the currently machining program finishes.
The next program is one of the valid index plane programs after the pallet in the
machine.
External workpiece coordinate set in the pallet detailed screen during search is set in
the external workpiece coordinate shift (EXT). Auto restart is disabled. If auto restart
is turned ON by PLC switch, it will be automatically turned OFF.
(5) Program Start ON/OFF Whether continuous start of the registered program is valid or invalid is displayed.
When valid, run the searched program for a pallet in the machine.
This setting is valid only when pallet program search is valid.
(6) Pallet information in the Whether pallet is in the machine is displayed.
machine • Mach. area: When pallet is in the machine
• Setup area: When pallet is not in the machine
I - 263
3. Setup Screen
Menus

The state (Machining, Program Search, Program Start) indicated by C Setting pallet program
ON the cursor is validated. search
The state (Machining, Program Search, Program Start) indicated by C Setting continuous start
OFF the cursor is invalidated.
Prev Information on the previous two pallets is displayed. C Changing display pallet
pallet
Next Information on the next two pallets is displayed. C
pallet
Pallet A list of pallets is displayed. B
list
Pallet The screen is shifted to the Pallet details screen. B 3.13.3 Pallet Details
details The 0° or 90° data of the pallet displayed on the top line of the Pallet Screen
list screen is displayed.
Operation method (Changing display pallet)
(1) When the pallet 1 and 2 are displayed, Pallet 3 and 4 are displayed.
press the Next pallet menu or next
page key.
(2) Press the Prev pallet menu or previous Pallet 1 and 2 are displayed.
page key.
Operation method (Setting pallet program search)
(1) Using the , , , keys, The contents set in "Program Search" is displayed.
move the cursor to "Program Search" and The cursor moves to "Program Start".
Operation method (Setting continuous start)
(1) Using the , , , keys, The contents set in "Program Start" is displayed. The
move the cursor to "Program Start" and cursor moves to "Program Search".
Every time the , , , or key is pressed, the cursor switches between "Program Search"
and "Program Start".
I - 264
3. Setup Screen
3.13.3 Pallet Details Screen
Machining program device, file name, machining status, Aux. and external workpiece coordinates for each
plane of the pallet 1 to 12 are set.
(5)
(1)
(6)
(2)
(3)
(4)
Display items

(1) Program Dev./Name Machining program device name and file name to be registered in each pallet's index
plane are displayed.
(2) Machining Whether machining for each pallet's index plane is valid or invalid is displayed.
ON/OFF
(3) Aux. If auxiliary function is available, data concerning auxiliary function for each pallet is
displayed. Refer to the instruction manual issued by the machine tool builder for
details on this function.
(4) Ext coord External workpiece coordinate for each pallet's index plane is set.
The value set in the external workpiece coordinate is written into the external
workpiece coordinate shift (EXT) according to the command from PLC.
When the external workpiece coordinate for the machining surface of a pallet in
machine is changed, only the changed axis data is written into the external workpiece
coordinate shift (EXT).
The set data (X to Z axis) is set in the pallet No. and extended workpiece coordinate
offset corresponding to the index plane.
X to Z axis: External workpiece coordinate data
(Example)
Pallet 1 0° : Extended workpiece coordinate offset 49 sets
:
I - 265
3. Setup Screen

(5) Pallet information in the Whether pallet is in the machine is displayed.
machine • Mach. area: When pallet is in the machine
• Setup area: When pallet is not in the machine
(6) Machined "Machined" is displayed on the index plane of a pallet in the machine.
(Note 1) The operation message "Pallet running" appears when the setting of "Program Dev.", "Program
Name", "Machining", or "Aux." is executed to the index plane under machining of a pallet in
machine. The "Program Dev.", "Program Name", "Machining", or "Aux." can be set when the
index plane of a pallet in machine is not under machining.
Even if the index plane of a pallet in machine is under machining, the external workpiece
coordinate can be set.
Menus

The device menu is displayed. C Setting values in each
When selected, device name of the pallet at the cursor position is index plane
Device
select changed.
When a device other than memory is selected, the route is displayed
first.
File File name to be registered can be selected from a list. C 3.13.1 Standard Pallet
set A list of files of the currently selected device is displayed. Registration (Selecting a
When the cursor is pointing at file name, this menu is operatable. file from the list)
ON The state (Machining) indicated by the cursor is validated. C Setting values in each
This menu can be used only when the cursor is at Machining. index plane
OFF The state (Machining) indicated by the cursor is invalidated. C
This menu can be used only when the cursor is at Machining.
Previous index plane is displayed. C Changing index planes
When 0° or 90° index plane is being displayed, this menu displays the
Prev previous pallet, 180° or 270° index plane. When 180° or 270° index
plane plane is being displayed, this menu displays 0° or 90° index plane.
When 0° or 90° index plane of the pallet 1 is displayed, this menu
cannot be selected.
Next index plane is displayed. C
When 0° or 90° index plane is being displayed, this menu displays
Next 180° or 270° index plane. When 180° or 270° index plane is being
plane displayed, this menu displays the next pallet, 0° or 90° index plane.
When 180° or 270° index plane of the last pallet is displayed, this
menu cannot be selected.
An arbitrary pallet can be selected. A Changing display pallets
Pallet When the pallet No. is set and the INPUT key is pressed, the 0° or 90°
select pallet details data for that pallet will be displayed. The cursor will move
to the 0° machining program file name.
The Pallet list screen will open. B 3.13.1 Standard Pallet
Pallet
list A list of pallets, including the pallet displayed on the Pallet details Registration
screen will appear.
Pallet This displays the pallet details. B
details
I - 266
3. Setup Screen
Operation method (Changing display pallets)
(1) Press the Pallet select menu. Input The pallet 5's 0° and 90° index plane will appear.
pallet No. and press the INPUT key.
5 INPUT
Operation method (Changing index planes)
(Example) When the screen display status acquired after the above (Changing display pallets) operation
(1) Press the Next plane menu or next The pallet 5's 180° and 270° index plane will appear.
page key.
(2) Press the Prev plane or previous page The pallet 5's 0° and 90° index plane will appear.
key.
The display of pallet and index plane changes as follows.

……
180°, 270° of the previous pallet
0°, 90°of the current pallet
180°, 270°of the current pallet
0°, 90°of the next pallet

……
I - 267
3. Setup Screen
Operation method (Setting values in each index plane)
(1) An arbitrary index plane is displayed using

the operation method above.
(2) Press the Device select menu and The cursor moves to "Device". The device menu
select a device. (Memory, HD, DS, FD, Memory card) is displayed. If
selected, the device selected in "Device" is displayed.
After setting, the cursor moves to "File name".
(3) Enter program No. in "File name". Contents set in "File name" is displayed. The cursor
moves to "Machining".
A file can be selected from the list, as well.
(4) Press the ON or OFF menu for The contents set in "Machining" is displayed.
"Machining". The cursor moves down.
(5) Move the cursor to "Ext coord" and input Values for 3 axes are set. The cursor moves to the
values for 3 axes. "Program File name" above.
I - 268
4. Edit Screens
4. Edit Screen
The Edit screen is used to edit the machining program (adding, erasing and changing), perform checks, and
input/output data.

The Edit screen is configured as shown below.
Left Right
area area
Left area :The contents differ depending on the display type.

Use the Display change menu or , key to switch the display type.
The tab at the upper section of the area depends on the option validity.
Right area: Displays the program searched to be edited.
When the multi-program display type is applied, use <--> change menu key to switch the
active area.
I - 269
4. Edit Screens
Menus

This edits the machining program. 4.2 Program Editing
This checks the program. 4.3 Program Check (2D)

This is used to check the machining program without performing 4.4 Program Check (3D)
automatic operation.
(1) Program check (2D)
This displays a graphic drawing of the machining program
movement path.
(2) 3D solid graphic check
This displays a solid graphic drawing of the workpiece shape and
tool movement during the cutting process in the machining
program.
This menu does not display if there is no program check function
option.
This creates the part program simply.
Refer to the following manuals for detail.
700/70 Series Simple Programming Function NAVI MILL Instruction
Manual (IB-1500144(ENG))
700/70 Series Simple Programming Function NAVI LATHE
Instruction Manual (IB-1500146(ENG))
This performs the machining program input and output between the 4.5 Program
NC internal memory and the external input/output device. Input/Output
I - 270
4. Edit Screens
4.2 Program Editing
4.2 Program Editing
This is used to edit (add, erase, change) the machining programs in the NC memory, HD, memory card
(front IC card), DS (compact flash) or FD, and to create new programs.
(In 70 series, only the memory and the memory card can be used.)
This function is used for three types of program: machining program, MDI program and fixed cycle program.
Press the main menu Edit key to display the program found when performing an operation search (MDI
program in MDI mode).
The contents of the left area depends on the display type:
Check display type :Enables to edit a program confirming the program check screen.
Multi-program display type :Enables to edit two programs using left and right editing areas.
G-code guidance display type :Enables to edit a program referring to the G code guidance.
Playback display type :Enables to edit program trying sample machining.
There are two types of editing available: regular editing and mass-editing. The specification and the
limitation are different between regular editing and mass-editing.
The conditions and the maximum edit size of mass-editing are as follows.
NC model Conditions of mass-editing Maximum edit size

700 series • Storage location of the opened machining program is FCU7-DA2-xx : 20MB
either HD, FD, memory card or DS. FCU7-DA3-xx/DA4-xx : 1GB
• The size of the file is 1.0MB or more. (Except when
parameter "#8910 Edit Undo" is "0", which needs
2.0MB or more.)
70 series • Storage location of the opened machining program is 10MB
memory card.
• The size of the file is 0.5MB or more.
(1)
(3)
(2)
(4)
(5)
I - 271
4. Edit Screens
4.2 Program Editing
Display items

(1) Path display This displays the path for the open program file.
(Ex.) Memory: /program
When the path is too long, the characters exceeding the 37 characters (1-byte code)
can not be displayed.
(2) Program name [Program name (file)]
This displays the file name of the program currently being edited.
This displays "MDI" when the MDI program name is being edited.
Top display line [Top display line, Last display line]
Last display line This displays the line number for the first and last line of the currently displayed
program. Proving an entire program is regarded as 100%, the position of the page
currently displayed is shown in percentage during mass-editing.
(3) N No. additional value [N No. additional value display]
display This displays an automatic additional value of sequence No.
Edit type display [Edit type display]
This displays "EX" in mass-editing.
Current edit display [Current edit display "Editing"]
"Editing" This displays when performing edit operations after displaying the program.
Insert mode display "INS" [Insert mode display "INS"]
This displays when pressing the INSERT key and changing to the insert mode.
(4) Line number [Line number]
This displays the last 3 digits of the program line number.
The line No. attaches only to the first line when over two or more lines are
displayed on the screen because one line is long.
The line No. does not attach during mass-editing.
Program display [Program display]
This displays the contents of the program (machining program, MDI program)
currently being edited.
The line with the cursor is emphasized. The line is not emphasized during mass-
editing.
(5) Input area This inputs the program line number and search character string.
Menus

This edits and references the existing programs. A 4.2.2 Editing a
Open When the program number is designated and the INPUT key is Machining Program
pressed, the program contents appear and can be edited.
This creates a new program. A 4.2.1 Creating a New
Open When the program number is set and the INPUT key is pressed, a Machining Program
(New)
new program is created.
This edits the MDI program. A 4.2.3 Editing MDI
MDI When this menu key is pressed, the MDI program appears and can Program
be edited.
This switches the active area between left and right editing areas. C 4.2.7 Changing the
←→ Editing can be done in the active area. Display
change
This menu can be used with the multi-program display type.
Line With regular editing, when the line number is set and the INPUT key A 4.2.8 Designating an
jump is pressed, the cursor moves to that line number. Arbitrary Line
With mass-editing, proving an entire program is regarded as 100%,

designate the position of the page to be displayed in percentage and
% jump press the INPUT key. The program data of the designated display
position is displayed on the screen. The cursor jumps to the top line of
the displayed program.
I - 272
4. Edit Screens
4.2 Program Editing

Line This copies the designated line (multiple lines can be copied.) A 4.2.14 Copying/Pasting
copy This menu cannot be selected during mass-editing. Data
Line This inserts the copied line at the line before the cursor. C
paste This menu cannot be selected during mass-editing.
Line This erases the designated line (multiple lines can be erased.) A 4.2.11 Deleting Data
clear This menu cannot be selected during mass-editing.
This returns the contents of the program to that prior to saving and C 4.2.15 Undoing Program
display. Changes
Undo This menu cannot be selected when parameter "#8910 Edit Undo" is
set to "0".
This menu cannot be selected during mass-editing.
In 70 series, this menu cannot be selected.
Display This switches the display type. C
change
Comment This changes whether to show or hide the comment field in the list. B
nondisp When the comment field is hidden, the file name field will be enlarged.
When the character string is designated and the INPUT key is A 4.2.12 Searching for
String Character Strings
search pressed, that character string is searched for.
If the character string to be searched for and the character string to A 4.2.13 Replacing
String be replaced are separated with a "/" and designated, when the Character Strings
replace INPUT key is pressed, the character string is replaced.
This enables the input mistake check for the program being edited. B 4.2.16 Correcting/
Miss This menu cannot be selected during mass-editing. Displaying Input
warning
This menu is only for 700 series. Mistakes
This moves the cursor to the next input mistake warning location. C
Next This menu cannot be selected during mass-editing.
miss
The sequence No. can be added automatically by pressing the A 4.2.17 Adding Sequence
N auto INPUT key after designating an additional value. No. (N No.)
add
This menu cannot be selected during mass-editing. Automatically
MDI This registers the MDI program in the memory. A 4.2.3 Editing MDI
regist This can be performed only when the MDI program is displayed. Program
This deletes the programs. When the name of the program to be A 4.2.5 Deleting a File
Erase erased is designated and the INPUT key is pressed, the
file
designated file is deleted.
I - 273
4. Edit Screens
4.2 Program Editing
4.2.1 Creating a New Machining Program
Operation method
(1) Press the menu Open (New) . The following menu appears.
Memory List Sort

Memory HD DS FD Close
card update change
(When specifications of all devices is valid.)
(2) Select a device. The selected device name and directory (Memory:
(Ex.) Menu Memory /Program) appear in the Device name, Directory
display column.
For the devices other than memory, root directory is
selected.
(3) Input the file name for the program to be If a program can be newly created, a program
newly created and press the INPUT containing only EOR is created.
key. The list display is closed.
(Ex.) 100 INPUT
(4) Edit a machining program. Refer to "4.2.6 Edit Operations" and later.
(5) Press the INPUT key. The created machining program is saved to the
device.
(Note 1) An error occurs if an existing program No. is set.

(Note 2) The texts in parentheses ( ) at the top block of the program is the comment.
(Note 3) The existing file cannot be set.
(Note 4) The characters that can be used for the file name and directory path are 1-byte number, 1-byte
capital alphabetical letters, and 1-byte symbols recognized by the system.
Note that the following characters cannot be used.
|, /, :, "," (comma), *, ?, ", <, >, a to z (small letters)
In addition, the following cases cannot be treated as the file name.
• When the extension is such as "$$$", "$$0", "$$1", "$$2", "$$3", "$$4", "$$5", "$$6", "$$7",
"$$8", "$$9".
• When the file name is 1-byte character "0" (zero).
(Note 5) Creation of a program is not possible for a program with 33 or more file name characters.
I - 274
4. Edit Screens
4.2 Program Editing
4.2.2 Editing a Machining Program
Operation method
(1) Press the Open menu. The following menu appears.

Memory List Sort

card update change
(2) Select a device. The selected device name and directory (memory:
(Ex.) Menu Memory /program) appear in the Device name, Directory
display column.
selected.
(3) Use the ↑ , ↓ , ↑ , ↓ keys to align

the cursor with target machining program.
The name of the machining program to be
edited can be input in the input area.
(4) Press the INPUT key. The program appears at the top if the file can be
opened.
The cursor moves to the head character of the
program. The mode enters the overwrite mode.
The list display is closed.
(5) Edit a machining program. Refer to "4.2.6 Edit Operations" and later.
(6) Press the INPUT key. The edited machining program is saved to the device.
(Note 1) An error occurs if a nonexistent program No. is set.

(Note 2) If the selected program is running or program restarting, it can be displayed but not edited.
An error occurs when the data is set or the INPUT key is pressed.
(Note 3) The fixed cycle program list displays when basic common parameter "#1166 fixpro" is set to "1".
(Note 4) Editable size differs depending on each device. When the editable size is exceeded, the
message "Can't edit because of size over" appears.
(Note 5) "Loading" is displayed in flickering until the file is opened.
(Note 6) Editing is not possible for a program with 33 or more file name characters.
(Note 7) When the program in search was edited, the program is searched again as follows depending
on the last operation.
Search -> Edit : The position in which ONB is displayed is searched again.
Search -> Reset 1-> Edit : The program top is searched again.
Search -> Reset 2-> Edit : The search is not executed. If a program was added or
deleted, the search position may shift.
Search -> Restart & Search -> Edit : The program top is searched again.
I - 275
4. Edit Screens
4.2 Program Editing
4.2.3 Editing MDI Program
Operation method
(1) Press the menu MDI . The menu is highlighted.

The MDI program is displayed from the head of the
active editing area. The cursor moves to the head
character of the program.
The mode enters the overwrite mode.
(2) Edit the MDI program. Refer to "4.2.6 Edit Operations" and later.
(Note 1) Before starting MDI operation, confirm that the MDI settings are completed. If "Editing" or "MDI
no setting" is displayed, the MDI operation cannot be started.
When the INPUT key is pressed, the head block will be searched, and the message "MDI
search complete" will appear. The setting will then be completed.
If the cursor is moved without editing, the block indicated by the cursor will be searched for
when the INPUT key is pressed.
(Note 2) If the INPUT key is pressed when the number of MDI program characters including EOB (;)
and EOR (%) exceeds 2000, "Memory capacity over" message will appear and the MDI
program will not be searched for execution.
Note that the contents edited after the MDI program is saved last will not be saved in the NC
memory.
4.2.4 Registering MDI Program in NC Memory
Operation method
(1) Press the menu MDI regist . The menu is highlighted and turned to the program
No. input wait status.
The cursor appears in the input area.
(2) Set the program No. to be registered and MDI program is registered in the memory. The
press the INPUT key. operation message "MDI entry complete" is displayed.
The menu highlight returns to normal. The cursor
returns to the program display area.
(Note 1) When the INPUT key is pressed without entering the program name, a setting error occurs.
(Note 2) When the entered program name already exists in the NC memory, the operation message
"Overwrite this file?(Y/N)" is displayed.
(Note 3) MDI programs cannot be registered in the NC memory in the following cases.
• When the setting is made for other than programs with the parameter "#1166 fixpro".
• During "Editing" is displayed.
• When the remaining size of program is smaller than the MDI program to be registered.
• When the remaining number of programs that can be registered is "0".
• Entered program name already exists in the NC memory, and the status is in automatic
operation or program restarting.
I - 276
4. Edit Screens
4.2 Program Editing
4.2.5 Deleting a File
Operation method
(1) Press the menu Erase file . The following menu appears.
Memory List Sort

card update change
(Ex.) Menu Memory /program) appear in the Device name, Directory
display column.
selected.
(3) Use the , , , keys to align

the cursor with target machining program.
deleted can be input in the input area.
(4) Press the INPUT key. The operation message "Erase? (Y/N)" appears.
(5) Press the Y or INPUT key. The file is deleted.
Press the N key not to delete. The list display is closed.
(Note) The file is not deleted in the following cases.

• The file that is to be deleted is currently being used in automatic operation.
• The file that is to be deleted is subject to edit lock B or C.
• Data protection key 3 is enabled.
• The file to be deleted is in the "program restarting" state.
4.2.6 Editing Operations

When the program is edited, the key input data is directly written into the program display area. All data is
overwritten from the cursor position. "Editing" appears on the right side of the file name display once input is
started.
Press the INPUT key to save the program to the device and clear the "editing" message.
The editing operations from when the file is actually opened are explained in the following sections.
These editing operations are common for the machining program and MDI program.
! CAUTION
If "there is no value after the G" command, the operation will be the "G00" operation when the
program is run due to key chattering, etc., during editing.
I - 277
4. Edit Screens
4.2 Program Editing
4.2.7 Changing the Display
Switching the active area
Switching the active area is possible only when the multi-program display type is selected.
Press the <--> change key to switch the active area between the left and right window.
Right side is active (can be edited) Left side is active (can be edited)
<--> change
Changing the display using the page changeover keys ( : Previous Page, : Next Page)
key: This displays one page of preceding lines of the current top line.
When there is less than one page of data, a page of data will be displayed including the data
currently displayed.
(The cursor moves to the last line of the screen. Cursor does not move in mass-editing.)
key: This displays one page of following lines of the current bottom line. (The cursor moves to the top
line of the screen. Cursor does not move in mass-editing.)
Changing the display with the cursor key
The cursor will move up one line in the program each time the cursor key ( , ) is pressed.
If the key is pressed at the top line of the program display area, the program will scroll up one line.
If the key is pressed at the end, the program will scroll down one line.
When a block is displayed over 2 or more lines, , keys move the cursor by block unit during regular
editing and by line unit during mass-editing.
↑ 1:N1 G28 X0. Y0. Z0.; ↓

2:N2 G92 X0. Y0. Z0.;
↑ 3:N3 G00 X-300. Cursor moves in same
Y-300. Z-300.; display.
4:N4 G01 X-200. Y-200.
F2000;
↓
11:N11;
↑ 12:N12 Z300.; ↓
13:Y200.;
14:;
Display scrolls without
moving cursor position.
I - 278
4. Edit Screens
4.2 Program Editing
Move the cursor using the tab keys ( |← : back tab/ →| : tab).
|← key : Moves to the start of the word where the cursor is currently positioned.
If the cursor is at the start of a word, it moves to the start of the previous word.
→| key : Moves to the word after the word where the cursor is currently positioned.
Cursor destination when |← key Current cursor position

pressed
Cursor destination when →| key
pressed
Cursor destination when |←
key pressed again
3 N3 G00 X-300. Y-300. Z-300.;
4 N4 G01 X-200. Y-200. F2000;
: :
(Note) Pressing |← →| keys or ← → keys does not make any difference in mass-editing.
Split display by word unit
In regular editing, program is split by word unit and displayed.

In mass-editing, program is not split by word unit and displayed as text data.
4.2.8 Displaying an Arbitrary Line
Operation method
(1) Press the menu Line jump . The menu is highlighted.

The cursor appears at the lower input area.
(2) Input the line No. The program appears with the set line No. at the
(Ex.) 6 INPUT head.
The cursor moves to the head.
The menu highlight returns to normal.
(Note 1) When "0" is input, the cursor moves to the first line.
(Note 2) When "E" is input, the cursor moves to the end.
I - 279
4. Edit Screens
4.2 Program Editing
4.2.9 Rewriting Data
Operation method
(1) Move the cursor to the position of the data

to be rewritten.
The cursor can be moved to one place to
the right of EOB (;).
(2) Set the data. The message "Editing" appears when setting is
started.
The data is set from the position of the cursor. Data at
the area is overwritten.
The cursor moves one space (character) at a time to
the right as the data is set.
(3) When one line of setting is completed, EOB ( ; ) is added to the set data and the data is fixed.
press the INPUT key. When newly creating data, the cursor moves to the
head of the next line.
When changing existing data, etc., the cursor does
not move.
(Note 1) Up to 255 characters can be input in one block in regular editing and 127 characters in mass-
editing.
(Note 2) When the cursor is on or one place to the right of EOB ( ; ), input data is inserted even if not in
input mode (refer to "4.2.10 Inserting Data".)
(Note 3) When changing to another function such as the program check, or to another screen such as
the operation screen when "Editing" displays, the operation message "Save current file? (Y/N)"
displays. If N key is pressed changing to the other screen once, and the Edit screen is
selected again, the program before editing operation will be displayed. (Edited contents will be
invalid.)
(Note 4) "Saving" is displayed in flickering during saving.
I - 280
4. Edit Screens
4.2 Program Editing
4.2.10 Inserting Data
Operation method
(1) Move the cursor to the position where

data is to be inserted.
(2) Press the INSERT key. The insertion mode is entered.

"INS" and "Editing" appear to the right of the file
name.
(3) Set the data. The data is inserted before the cursor position. Data
after the cursor moves to the night.
(4) When the setting is completed, press the The set data is fixed.
INPUT key. The cursor does not move, but if there is no EOB ( ; )
at the end of the line, it will be added. Then, the cursor
moves to the next line.
The mode returns to the overwrite mode, and the
message "Editing" disappears.
(Note 1) Up to 256 characters can be set in one line.

(Note 2) The insertion mode will be finished if a key such as DELETE , C.B , CAN , INPUT , ↑,
↓ , ← , →, |←, →| , or pressed.
(Note 3) During regular editing, EOB ( ; ) is added to the line without EOB ( ; ) before moving to the next
line; EOB ( ; ) is not added to the the line with EOB ( ; ). (No cursor movement.)
(Note 4) During mass-editing, linefeed is inserted every time EOB ( ; ) is input. (Cursor moves to the
head of next line.)
I - 281
4. Edit Screens
4.2 Program Editing
4.2.11 Deleting Data
Operation method (Deleting one character)
(1) Move the cursor to the character to be

deleted.
(2) Press the DELETE key. 1 character is deleted at the cursor position, and
"Editing" appears. The data from the cursor position
moves to the left.
When this key is held down, the characters can be
deleted one at a time.
(3) Press the INPUT key. The edited machining program is saved to the device
and "Editing" disappears.
Operation method (Deleting one line)
(1) Move the cursor to the line to be deleted.
(2) Press the C.B key. 1 line is deleted at the cursor position, and "Editing"
appears. The lines following the cursor position are
shifted upward. The cursor position does not change.
When this key is held down, the line can be deleted
one at a time.
(Note 1) In the case where the block for the deleted line covers multiple lines, these lines are also
deleted.
(Note 2) Last line only with "%" cannot be deleted.
I - 282
4. Edit Screens
4.2 Program Editing
Operation method (Deleting designated lines)

(2) Designate the deletion range. The background color for the range to be deleted
(Ex.) From line 8 to line 10 turns light blue.
8/10 INPUT The message "Erase? (Y/N) " appears.
When deleting 1 line, it is also possible to

make a selection using the ↑ , ↓ keys
and designate by pressing the INPUT
key.
(3) Press the Y or INPUT key. The data in the range with the blue background is
deleted and the menu highlight returns to normal.
Press the N key not to delete. The lines following the deleted data are shifted
upward.
The cursor position and top line No. do not change.
(Note 1) If the INPUT key is pressed without setting a line No., the line where the cursor is will be
deleted.
(Note 2) If the last line of the file is the range to be deleted, the last line can be designated as "E".
(Example) From 8th line to last line : 8/E
From 1st line to last line: /E
(Note 3) Mass-editing has restrictions below.
• The range has to be within 100 lines.
• Last line designation switch "/E" is invalid.
(Note 4) "Executing" is displayed in flickering during line clear.
Operation method (Deleting several lines (one screen of data) displayed on a screen)
(1) Press the CAN key. Data (machining program) for 1 screen is deleted, and
"Editing" appears.
I - 283
4. Edit Screens
4.2 Program Editing
4.2.12 Searching for Character Strings
Operation method
(1) Press the String search menu. The menu is highlighted.

(2) Set the character string to be searched A search for a character string is made from the
for, and press the INPUT key. character after the cursor position downwards.
If the character string is discovered, the cursor moves
(Ex.) G20 INPUT
to the start of that character string.
A message appears if there is no character string
applicable to the program.
Marking can be performed by adding an option to the
character string being searched for.
((Ex.) G20/MR :G20 are marked in red.
(Refer to the "Marking function" for further details.)
(3) To continue searching, press the INPUT The next corresponding character string is searched
key again. for.
The search finishes when the end of the program is
reached.
(Note) It is not possible to return to the head of the
program and resume the search. To search
from the head of the program, move the
cursor to the top line and carry out the search
operation again.
(4) To end the search, press the menu key. The menu highlight returns to normal, and the
character string in the input area disappears.
The search mode is held until the menu key is
pressed.
(The character string remains in the input area.)
(Note 1) "Executing" is displayed in flickering during string search.
I - 284
4. Edit Screens
4.2 Program Editing
Marking function
Marking can be performed by adding an option to the character string being searched for.
Argument character string

Details Marking color
format
"Search character string" The cursor moves to the character string searched for. None
"Search character string/MR" The cursor moves to the character string searched for. Red
All displayed searched character strings are marked in red.
"Search character string/MB" The cursor moves to the character string searched for. Blue
All displayed searched character strings are marked in blue.
"Search character string/MG" The cursor moves to the character string searched for. Green
All displayed searched character string are marked in
green.
"/MC" The marking for all marked character strings is cleared. -
"/MCR" The marking for character strings marked in red is cleared. -
"/MCB" The marking for character strings marked in blue is cleared. -
"/MCG" The marking for character strings marked in green is -
cleared.
(Note 1) The marking status is maintained when another program is opened while character strings are
still marked.
(Note 2) If the input mistake check warning function is enabled while character strings are still marked,
the marking is given priority in the case where the input mistake location and the marked
display overlap.
(Note 3) In the case where the search marking and input mistake check warning function are displayed
simultaneously, the marking is cleared and the input mistake warning display remains.
(Note 4) With the multi-program display type, the search and marking is valid only in the area where the
search and marking is carried out.
(Note 5) The marked status is maintained until the NC power is turned OFF.
(Note 6) Marking function is invalid in mass-editing.
Important points when performing search
(1) If the designated character string cannot be found, a "Designated character string not found" message
displays.
(2) A search is performed for a character string containing the designated character string, irrespective of
the characters before and after. As a result, if "G2" is designated, G20 - G29 and G200 etc. will also
be the subject of a search.
Character string data setting example

Designated character
Search character string example
string
N10 Character strings that include "N10" such as "N10" and "N100".
N10 X100. Character string "N10 X100".
x-012.34 Character string "X-012.34" (A search is not performed for "X-12.34".)
I - 285
4. Edit Screens
4.2 Program Editing
4.2.13 Replacing Character Strings

A character string in a program can be searched for and replaced.
The following two methods can be used.
• The applicable character string is searched for and replaced one by one. (To search for the next
character string, press the INPUT key.)
• All applicable character strings in the program are replaced in a batch. (Designate "/G" when setting.)
Operation method
(1) Press the menu String replace . The menu is highlighted.

(2) Designate the search character string and The character string is searched downward from the
the replace character string. character after the current cursor position.
((Ex.) Search character string: G02 If a character string is discovered, the cursor moves to
Replace character string: In the the start of that character string, and a "Replace?
case of G03 (Y/N) " message appears.
G02/G03 INPUT (Note 1) If any character string is not found in the program, the
cursor does not move.
(3) Press the Y or INPUT key. The character string is replaced, and a search is
performed for the next applicable character string. (If a
Press the N key not to replace. batch replacement is performed, a search is not made
as the replace has been completed.)
A "Designated character string not found" message
appears when the end of the program is reached.
"Editing" appears if replace is performed.
(4) Press the Y or INPUT key again if The same operation as above is performed.
continuing the search/replace.
(5) To end search/replace, press the The menu highlight returns to normal, and the
String replace . character string in the input area disappears.
The replacement mode is held until the menu key is
pressed.
(The character string remains in the setting area.)
(Note 1) When batch replacing for all the character strings in the program, add "/G" to the above setting.
Search character string/replace character string/G (Ex.) G02/G03/G
During batch replacement, after replacing all character strings to the end of the program, the
process ends while showing the last character string replaced. Note that the replacement mode
is held, and the character string remains in the input area.
(Note 2) If the program character strings from the current cursor position to the last line are to be
replaced in a batch, add "/E" to the above setting.
Search character string/replace character string/E (Ex.) G02/G03/E
(Note 3) "Executing" is displayed in flickering during string replace.
I - 286
4. Edit Screens
4.2 Program Editing
4.2.14 Copying/Pasting Data
Operation method (Copying)
(1) Press the Line copy menu. The menu is highlighted.

(2) Designate the range to be copied. The background color for the range to be copied turns
(Ex.) From line 8 to line 10 light blue.
8/10 INPUT The menu highlight returns to normal.
When copying 1 line, it is also possible to

make a selection using the ↑ , ↓ keys
and designate by pressing the INPUT
key.
Notes when copying
(1) If INPUT key is input without setting a line No., the line where the cursor is at is copied.
(2) The highlight of the copy target lines disappears when editing operations are resumed.
(3) If the file is edited after the Line copy menu is pressed, the data copied in the line is canceled.
(4) If the last line of the file is the range to be copied, the last line can be designated as "E".
(Example) From 8th line to last line : 8/E
(5) The copied data is maintained while the copy source file is opened even if the display type or editing
area is switched to another one.
(6) Up to100 lines can be copied in mass-editing.
Operation method (Pasting the copied data)

is to be pasted.
(2) Press the Line paste menu. The copied data is inserted in the line before the
cursor position, and "Editing" appears.
(3) Press the INPUT key. The edited machining program is saved to device, and
"Editing" disappears.
(Note 1) With multi-program display type, data can be copied and pasted between both left and right
areas.
(Note 2) Copy/past is not possible in between regular editing and mass-editing.
(Note 3) "Executing" is displayed in flickering during line paste.
I - 287
4. Edit Screens
4.2 Program Editing
4.2.15 Undoing Program Changes

This is used to return the program to the form when INPUT was last pressed to save. This operation is
valid for the operation of "Rewriting program", "Insert", "Delete", "Line Paste", "Line Clear", "Character String
Replace" and "Undo" functions.
Operation method (Pasting the copied data)
(1) Change to memory mode and press the The searched program appears from the top.
main menu Edit key.
(2) Move the cursor to the position to be The data is replaced with input data and " Editing"
corrected, and input a character. appears.
(Ex.) 135
(4) Press the menu Undo . The contents of the file return to the same condition
as when the editing was started in the procedure (1).
These contents of the file are saved to the device.
(5) Press the menu Undo again. The contents of the file return to the same condition
as when the file was saved in the procedure (3).
These contents of the file are saved to the device.
(Note1) This function is only valid when parameter "#8910 Edit Undo" is set to "1".
(Note2) When returned to the previous status, the cursor will move to the head line.
(Note3) With the multi-program display type, returning to the previous contents is valid only in the active
area.
(Note 4) Undoing is not possible in mass-editing mode.
(Note 5) "Executing" is displayed in flickering during undoing.
I - 288
4. Edit Screens
4.2 Program Editing
4.2.16 Correcting/Displaying Input Mistakes [700 series only]

The input mistake check warning function regards the following cases as input mistakes and displays a
warning.
Check Item Warning display range Details
No decimal point input Applicable address and data The decimal point was omitted from the data.
(Ex.) N01 G0 X100 Y50.;
"X100" displayed as warning
The addresses to check no decimal point input are shown below.

({: Check performed, -: No check performed)
Decimal point Decimal point
Address Application M/L
command check
A Enabled Coordinate position data {
Disabled Miscellaneous function code Only for axis name
Enabled Geometric linear angle data
Disabled Rotation table M
Disabled MRC program number L
Disabled Data settings, axis number L
Enabled Deep hole drilling cycle (2) Safety distance L
B Enabled Coordinate position data {
C Enabled Coordinate position data {
Enabled Corner chamfering amount (.C)
Enabled Program tool compensation input Nose R compensation L
amount (increment)
D Disabled Compensation number (tool position, tool radius M -
Enabled compensation) L
Enabled Auto tool length measurement, deceleration range d L
Disabled Data settings M
Sub-program storage device number (.D)
E Enabled N number of threads per inch, precision thread lead -
F Enabled Feedrate -
Enabled Thread lead
G Enabled Preparation function code -
H Disabled Sequence number in sub-program -
Disabled Compensation number (tool position, tool length M
compensation)
I Enabled Circular center coordinates {
Enabled Vector component for tool radius compensation/nose R
compensation
Enabled Custom fixed cycle hole pitch M
Enabled 1st cut amount for deep hole drilling cycle (2) L
J Enabled Circular center coordinates {
compensation
Enabled Custom fixed cycle hole pitch, angle M
Disabled Dwell at deep hole drilling cycle (2) return point L
I - 289
4. Edit Screens
4.2 Program Editing

command check
K Enabled Circular center coordinates {
compensation
Disabled Custom fixed cycle hole count M
Disabled Hole drilling cycle repeat count L
Enabled 2nd cut amount for deep hole drilling cycle (2) L
Disabled Fixed cycle repeat count M
L Disabled Sub-program repeat count -
Disabled Fixed cycle repeat count M
Disabled Program tool compensation input type selection (L2, L10, L
Disabled L11) L
Data setting selection (L70)
M Disabled Miscellaneous function code -
N Disabled Sequence number -
Disabled Data setting, data number L
O Disabled Program number -
P Enabled/Disabled Dwell time (parameter) -
Disabled Sub-program call program number
Disabled Program tool compensation input compensation number
Disabled Custom fixed cycle hole count M
Disabled Helical pitch count M
Disabled Surface speed radius M
Enabled Scaling factor M
Disabled High-speed mode type M
Disabled 2nd reference position number L
Disabled Constant surface speed control axis number L
Disabled MRC finished shape start sequence number L
Enabled Cut-off cycle, shift amount/cut amount L
Disabled Compound thread cutting cycle cut count, chamfering, nose L
angle
Enabled Compound thread cutting cycle thread height L
Disabled Data settings large division number L
Disabled Restore sequence number fro sub-program L
Enabled Coordinate position data L
Q Enabled Deep hole drilling cycle cut amount M -
Enabled Back boring shift amount M
Enabled Fine boring shift amount M
Disabled Spindle minimum clamp rotation speed L
Disabled MRC finished shape end sequence number L
Enabled Cut-off cycle cut amount/shift amount L
Enabled Compound thread cutting cycle minimum cut amount L
Enabled Compound thread cutting cycle 1st cut amount L
Enabled Cut amount each time for deep drilling cycle 1 L
Disabled Program tool compensation input hypothetical nose point L
number
Disabled Dwell at cut point for deep drilling cycle 2 L
I - 290
4. Edit Screens
4.2 Program Editing

command check
R Enabled R-designated circular radius {
Enabled Corner rounding circular radius (.R)
Enabled Program tool compensation input compensation amount
Enabled Fixed cycle R point M
Disabled Synchronous tap/asynchronous tap change M
Enabled Auto tool length measurement deceleration area r L
Enabled MRC longitudinal, edge, and escape amount L
Disabled MRC molding division amount L
Enabled Cut-off cycle return amount L
Enabled Cut-off cycle escape amount L
Enabled Compound thread cutting cycle finishing allowance L
Enabled Compound thread cutting cycle, cutting cycle taper difference L
Enabled Distance to R point for hole drilling cycle, deep hole drilling L
cycle 2
Enabled Coordinate position data L
S Disabled Spindle function code -
Disabled Spindle maximum clamp rotation speed L
Disabled Constant surface speed control surface speed L
T Disabled Tool function code -
U Enabled Coordinate position data {
Disabled 2nd Miscellaneous function code L Only for axis name
Enabled Program tool compensation input L
V Enabled Coordinate position data {
Disabled 2nd miscellaneous function code L Only for axis name
W Enabled Coordinate position data {
X Enabled Coordinate position data {
Enabled Dwell time Only for axis name
Disabled 2nd miscellaneous function code L
Y Enabled Coordinate position data {
Z Enabled Coordinate position data {
I - 291
4. Edit Screens
4.2 Program Editing
Performing a consecutive input mistake check when creating a program
(1) Press the menu Open (New) , input a Only an EOR program is created.
new file name, and press the INPUT
key.
(2) Press the Miss warning menu. The menu is highlighted.
(3) Edit the program. A warning is displayed at the moment the INPUT
key is pressed.
(4) Correct the input mistake and continue

with program creation.
I - 292
4. Edit Screens
4.2 Program Editing
Performing a batch input mistake check for an existing program
(1) Change the operation to memory mode or

MDI mode and perform a machining
program operation search.
(2) Press the Edit menu. Machining programs appear from the top.
(3) Press the Miss warning menu. A warning displays the position where an input
mistake occurred. The cursor moves from its current
position to the first input mistake that was found.
(4) Press the Next miss menu. The cursor moves to the next input mistake position.
(5) Correct the input mistake and continue

with program creation.
I - 293
4. Edit Screens
4.2 Program Editing
Precautions
(1) The input mistake check timing is outlined in the following table.
Timing Check range Check item Example

When an edit key (alphabet, 1 block where the Decimal point A warning is displayed upon
numbers, symbols, [Delete] cursor is located pressing INPUT when "X10;" is
etc.) is pressed (Does not input.
include the cursor key and A warning is displayed upon
[Page Up/Down] keys.
pressing INPUT when the
"X10.Y" "." is inserted in the case
where "X10Y" is input.
If the Miss warning menu is pressed again when the input mistake check warning function is enabled,
this function is then disabled.
The character color of the location of an input mistake then returns to normal.
(2) The Next miss menu is grayed out and cannot be selected when the Miss warning menu is not
highlighted.
(3) An input mistake check warning function can be performed even when editing a MDI program.
(4) An input mistake check warning function can also be performed for a comment block.
(5) If the data in an address that is subject to a decimal point input mistake is "0", no warning is issued
regardless of the presence of a decimal point.
((Ex.) No warning is issued for "X0")
If the data in an address that is subject to a decimal point input mistake has been omitted, no warning is
issued.
((Ex.) No warning is issued for "G28XYZ")
(6) Blocks with " [","]" are not subject to an input mistake check warning function.
(7) The input mistake status is held in the operation screen edit window, setup screen MDI edit window, and
edit screen edit area.
(8) If an input mistake is found after the current cursor position, the "Input miss was detected" message
appears. If no input mistake is found, the "Input miss was not detected" message appears.
(9) With the multi-program display type, the input mistake check is performed also in the non-active area.
Note that the messages “Input miss was detected" and "Input miss was not detected" will be displayed
by judging the input mistake referring to the cursor position in the active area.
(10) Input mistake check warning function is disabled in mass-editing.
(11) "Executing" is displayed in flickering during checking input mistakes.
I - 294
4. Edit Screens
4.2 Program Editing
4.2.17 Adding Sequence No. (N No.) Automatically
When the sequence No. (N No.) is input once, the sequence No. to which a constant value is added can be
automatically added to each block of the machining program.
The added sequence No. data is to N2 to N999999.
This function is disabled during mass-editing.
Operation method
(1) Press the menu N auto add. The menu key is highlighted and turned to the
additional value input wait status. The cursor appears
in the input area.
(2) Input the additional value. "N+10" is displayed in N No. additional value display
(Ex.) 10 INPUT column. The cursor moves from the input area to the
edit area.
<When creating a new program>

(3) Press the menu Open (New), then press The list appears as a pop-up window. The machining
the menu Memory. programs in memory are displayed.
(4) Input a file name not used, then press the "O100" is created in edit area.
INPUT key.
(Ex.) 100
(5) Input a program with N No.

(Ex.) N100G28XYZ
<When editing an existing program>

(3) Press the menu Open, then press the The list appears as a pop-up window. The machining
menu Memory. programs in memory are displayed.
(4) Select a file, then press the INPUT key. The selected file is opened in edit area.
(5) Move the cursor to the position where

data is to be inserted. Press the INSERT
key.
(6) Input " ; " (EOB). "N110" (previous block N No. "N100" + an additional
value "10") is added after a " ; " (EOB).
I - 295
4. Edit Screens
4.2 Program Editing
(7) Input the second block data and " ; " "N120" is added behind " ; ".
(EOB).
(Ex.) G92X0.Y0.Z0.;
(8) Press the INPUT key. The message "Editing" disappears. The program
is saved.
The N No. data is automatically generated until the

edit is interrupted with the INPUT key.
(Note 1) When the menu N auto add is pressed again while the menu is highlighting, N No. additional
value display column is cleared, and N No. automatic addition is canceled.
(Note 2) The setting range is 1 to 1000. When "01" is input, "1" is set. When "0" is input, this function is
canceled. When an illegal value or 9 characters or more is input, an error will occur.
(Note 3) The additional value can be set even when the machining program has been not opened. Even
if the machining program is opened again, the additional value is not invalid.
(Note 4) This function is enabled only during regular editing of edit screen.
(Note 5) This function is disabled during mass-editing. However, the set N No. additional value in regular
editing is not cleared, and the additional value is valid during regular editing again.
(Note 6) Even if the same N No. exists by automatic addition, an error will not occur.
(Note 7) The system separately has N No. in a right area and left area of the edit screen.
(Note 8) When the previous block is leading zero like "N010", N No. automatic addition can be executed.
However, "0" is not added, and "N10" is displayed.
I - 296
4. Edit Screens
4.2 Program Editing
Example when N No. is added
(1) When the previous block has N No. (When the cursor is located at the last character in the overwrite
mode.)
N100 G28 X0 Y0 Z0 ; -> Input ";" -> N100 G28 X0 Y0 Z0;N110;
N100 G28 X0 Y0 Z0 ; -> Input ";" -> N100 G28 X0 Y0 Z0 ;N110;
N100 G28 X0 Y0 Z0 ; -> Input ";" -> N100 G28 X0 Y0 Z0 ;N110;
(2) When the previous block has N No. (When the insertion mode)
N100 G2 8 X0 Y0 Z0 ; -> Input ";"-> N100 G2;N110 8 X0 Y0 Z0 ;
N100G28X0Y0Z0; N200G90X20.Y20.Z20.;
-> Input ";"-> N100G28X0Y0Z0;N110 N200G90X20.Y20.Z20.;
Example when N No. is not added
(1) When the previous block has no N No.

G00X10.% -> Input ";" -> G00X10.;%
(2) When the head of previous block has no N No.
Usually
G00N100X10.% -> Input ";" -> G00N100X10.;%
When comment
(N100)G00N100X10.%-> Input ";" -> (N100)G00N100X10.;%
When the previous block has a space
N100G00N100X10.% -> Input ";" -> N100G00N100X10.;%
(3) When the N No. of previous block is over 9 characters.
N000001000% -> Input ";" -> N000001000;%
(4) When limits of total characters display per block is exceeded.
(5) When the N No. is over 1000000.
(6) When the N No. automatic additional value is not set.
(7) When the display character string in overwrite mode is interrupted.
N100 G28 X0 Y0 Z0 ; -> Input ";" -> N100 G28 X0;Y0 Z0 ;
I - 297
4. Edit Screens
4.2 Program Editing
4.2.18 G Code Guidance

G code guidance is a function that shows the command format details or the outline of its operation for the G
code being edited while creating or editing the machining program. With this function, the G code format can
be confirmed immediately. G code guidance is also displayed in the same manner even when MDI program
is displayed.
G code guidance function is valid for the M system.
<G code guidance>
The contents displayed on the G code guidance area depends on the cursor position on the Edit screen, and
is refreshed when moving the cursor.
The G code that meets following conditions are displayed in this area.
• G code that exists between the head of block and cursor position including the cursor position.
• G code that exists immediately before the cursor if multiple G codes meet the above condition.
Specific example
G91 G17 ; The guidance will not be refreshed because the cursor
is out of the block.
G91 G17 ; The guidance for G17 will be displayed.
G91 G17 ; The guidance for G91 will be displayed.
G91 G00 X100. Y100. ; The guidance for G00 will be displayed because G00
is the nearest G code to the cursor.
I - 298
4. Edit Screens
4.2 Program Editing
G codes displayed in the G code guidance area
With G code guidance function, the commands having "G" followed by 1 or more numbers are regarded as
the G code. Thus, when "G" that is located immediately before the cursor is within the comment, the
guidance will not be refreshed. In the same manner, when a G code is commanded using variables such as
"G#100" or "G#500", etc. but numbers, the guidance will not be refreshed.
The G code that can be displayed in the guidance area is as follows.
Gnnnnnnnn.m L ll("n", "m", and "l" are arbitrary number.)

Number of
Commanded value Remarks
valid digits
n 1 to 8 When including "0" before integer command value,

(integer) unnecessary "0" is ignored.
m 0, 1
(decimal places)
l 0 to 2 This is valid when "L" exists immediately after the integer
(value commanded using command value or decimal command value and is
"L") followed by a command value.
If the command with "L" address precedes G code, the "L"
command will not be described in the guidance.
(Note 1) As for the G codes not included in the specifications, the guidance will not be displayed even if
the above condition is met.
G00 X100. (GCODE) ; "G" included in the comment "GCODE" is ignored,

thus, G code guidance will not be refreshed.
N11 GOTO12 ; "G" included in the command "GOTO" is ignored,

G91 G120 X100. Y100. ; G code "G120" is not included in the specifications,
G00000031.1 ; The guidance for G31.1 will be displayed.
G00000031.10 ; Commanded value exceeds the number of valid digits,

L50 G10 ; The guidance not for "G10 L50" but "G10" will be
displayed.
I - 299
4. Edit Screens
4.2 Program Editing
Precautions for G code guidance
(1) G code guidance may be refreshed when the cursor is located near the comment.
[Ex.] ( PROG01 ) ; The guidance for G01 will be displayed.
(2) When the cursor is located at the axis address, etc., the guidance for the nearest G code will be
displayed even if the address has no relationship with the G code.
[Ex.] G01 G90 X100. ; G code that has a relationship with "X100. " is "G01",
however, G code guidance for "G90" will be displayed.
(3) When moving the cursor to the block with no G code as follows, the contents of guidance will differ
depending on the cursor’s route even if the cursor is in the same block.
[Ex.] N01 G91 G01 X100. F1000 ; When the cursor is moved by the route "a", the
guidance for G01 which is displayed last in N01 block
↓ will also be displayed in N02 block.
N02 Y100. Z100. ; ← ... a When the cursor is moved by the route "b", the
guidance for G02 which is displayed last in N03 block
↑b
will also be displayed in N02 block.
N03 G02 X50. Y50. R50. ;
(4) G code guidance will be refreshed even if an option of the G code is not valid. Thus, G code could not
function though the guidance is displayed.
(5) Basically, G code format in the guidance is displayed using the format of 3-axis specifications of X, Y,
and Z.
(6) Whichever plane is selected among the plane selection functions G17 to G19, the display data in the
guidance is displayed using X-Y plane (G17) format.
(7) When the G code command includes an address which have two or more meanings, both contents will
be displayed.
(8) G code guidance will not be refreshed while the character string is searched or replaced.
(9) G code guidance cannot be displayed in mass-editing.
I - 300
4. Edit Screens
4.2 Program Editing
4.2.19 Playback Editing

The playback function enables creation of a program while trying sample machining by manual (handle or
jog) feed or mechanical handle feed.
A machining program can be created with movement distance data obtained by manual operation used as
programmed command values.
For L system, the playback counter and valid address key (X, Y, U, V, etc.) are different depending on the
parameter "#1076 AbsInc" (ABS/INC address) setting.
#1076 AbsInc
#1126 PB_G90 Reference
(For L system only)
M system (This setting is meaningless.) 0 (Incremental value) Absolute/incremental
1 (Absolute value) command depending
L system 0 (Absolute/incremental command (This setting is meaningless.) on G command
depends on G command)
1 (Absolute/incremental command Absolute/incremental
depends on address code) command depending
on address code
<Absolute/incremental command depending on G command>
(1)
(2)
(3)
<Absolute/incremental command depending on address code>
(1)
(2)
(3)
I - 301
4. Edit Screens
4.2 Program Editing
Display items

(1) Machine position counter This displays the machine position counter.
Up to max. number of axes in a part system can be displayed.
M system Max. eight axes
L system Max. five axes, the sixth axis or more is switched by the menu [Next
axis].
When the rotary axis (except for all coordinate linear type), the display range is
0.000° to 359.999°.
(2) Playback counter This displays the playback movement amount (axis movement value).
When "absolute/incremental command depending on G command", the title and
playback movement amount differs according to the parameter "#1126 PB_G90".
When "Absolute/incremental command depending on address code", both titles are
displayed.
#1126 PB_G90 Title Playback movement amount
0 (Incremental value) Playback: INC Playback movement amount
before axis moves + axis
movement amount
1 (Absolute value) Playback: ABS The program position + manual
interrupt amount
Up to max. number of axes in a part system can be displayed.
M system Max. eight axes
L system Max. five axes, the sixth axis or more is switched by the menu [Next
axis].
When the rotary axis (except for all coordinate linear type), the display range is
following below.
Rotary INC -359.999° to 359.999°
axis (Rotary type short-cut invalid, workpiece coordinate linear type)
-180.000° to 179.999° (Rotary type short-cut valid)
ABS 0.000° to 359.999°
(3) Playback editing area The contents of playback editing is input. When the axis address keys such as X and
Y are input, the playback counter value currently displayed is input after the axis
address.
I - 302
4. Edit Screens
4.2 Program Editing
Operation method (Absolute/incremental command depending on G command)
(1) Set "#1126 PB_G90" to "0" on the Incremental value mode is set.
parameter screen.
(2) The menu Display change or key is The "playback display type" is displayed.
press several times on the edit screen. The menu <--> change cannot be used.
When the incremental value is set, the initial value is

"0".
(3) Open the program pressing Edit and The selected program is displayed in right area.
Open on the edit screen.
(4) Move the axis during manual mode. The axis movement amount is displayed in playback
movement amount.
In the incremental value mode, the axis movement

amount by manual mode is added to currently
playback movement amount.
I - 303
4. Edit Screens
4.2 Program Editing
(5) Input the data such as the G codes in the The alphanumeric characters, ←, → and DELETE
area for playback editing.
keys can be input in the area for playback editing.
(6) Press the axis address key such as X or The playback movement amount is input after the axis
Y. address in the playback editing area. If the axis
address key is pressed while the playback movement
amount is being changed, the playback movement
amount at the time the key was pressed will be input.
(Note) When inputting a comment, etc., the

characters that are the same as the axis
address will all be handled as the axis
address.
(7) Press the INPUT key. The program in the playback editing area will be
inserted at the block before the cursor position in the
right area, and the program is saved.
When there is no "EOB" (;) at the end of the character
string, it is added automatically.
The cursor moves to the line head being cleared the
content of the playback edit.
For an absolute value, the playback movement
amount will not change.
For an incremental value, the difference of the axis
command value for the axis used in step (6) and the
playback movement amount will remain as the
playback movement amount.
(Note) If the program is not displayed on right area,
the operation message "Can't execute
playback edit" appears.
(Note 1) When the program is not displayed on the right area, a playback editing cannot be executed.
(Note 2) When the C.B key is pressed, all data in the playback editing area will be erased.
(Note 3) When the and keys are pressed, the program cursor on the right area will move.
(Note 4) When the page-switching key is pressed, the program on the right area will scroll.
(Note 5) When the menu key is pressed, the process corresponding to the right area will run.
I - 304
4. Edit Screens
4.2 Program Editing
Operation method (Absolute/incremental command depending on address code)
(1) Confirm that the parameter "#1076

AbsInc" is "1".
(2) Edit a program the same as the procedure

(2) to (6) of "Absolute/incremental
command depending on G command".
Notes for playback editing
(1) Playback editing of a program in automatic operation or program restart is not possible.
(2) Up to 95 characters can be edited in the playback editing area.
(3) If the screen/part system is changed or the program file is opened when the input program is in the
playback edit area, the program being edited will be aborted.
(4) Other files can be opened during playback editing. Playback editing can be continued even when other
file is opened. However, if an incremental value is designated, the playback movement amount will be
cleared to 0 for all axes. A new file can be created and edited, and MDI editing carried out in the same
manner.
(5) If the program being playback edited automatically starts, playback editing cannot be continued.
(6) The playback movement amount after playback editing will differ according to the parameter "#1126
PB_G90" state and the commanded G code. The playback movement amount after INPUT is pressed is
calculated for each block that has been playback edited.
X axis playback X axis playback movement amount after INPUT
Details to be
movement
playback
amount before For an absolute value For an incremental value
edited
editing
X 100.000 G01 X10.; X 100.000 X 90.000
The program position + The difference of the axis
manual interrupt amount is command value (X10.) and
inserted as the playback playback movement amount
movement amount. before INPUT (X100.) is
inserted as the playback
movement amount.
G92 X10.; X 10.000 X 0.000
The command value (X10.) Regardless of the command
following G92 is inserted as value following G92, 0 is
the playback movement inserted as the playback
amount. movement amount.
(7) The playback editing is disabled during mass-editing.
(8) Do not set the same address to the parameter "#1013 axname" and "#1014 incax". If the same address
is set, the absolute counter has priority. (However, the same address as the address used in other part
system can be specified.)
I - 305
4. Edit Screen
The program check function (2D) is used to graphically draw the machining program movement path without
performing auto operation.
The machining program can be checked with graphic data drawn at a high speed.
(Note1) The program check (2D) function is an additional specification. The graphic check option is required.
(Note2) When changing the screen to the edit screen, display depends on the previous checking type
(2D/3D). Note that when selecting this screen during graphic trace, 3D solid program check will apply.
If the 3D solid check option is not valid in this time, the area of “Check” tag will not be blank.
■Normal display (full-screen display mode is OFF)
< Drawing area >
(8)
(1)
(9)
(2)
(3)
(4)
(5)
(6)
< Drawing area: 2-plane > < Input area displayed >
(7)
I - 306
4. Edit Screen
■Full-screen display (full-screen display mode is ON)

< Drawing area >
(1)
(3) (5)
(8)
(9)
(2)
(6) (4)
Display items

(1) Check counter This displays the axis counter for the check drawing. The displayed counter type and
axis name (3 axes) are set in the parameters.
[Counter]
#1231 set03 (bit5) 0: Machine position counter,
1: Workpiece coordinate position counter
[Axis name]
#1026 to #1028 base_I, base_J, base_K
(Note) When the setting values of #1026 to #1028 have been changed, the changed
values will be reflected in the check counter display when the power is turned
ON again.
(2) Display mode This shows the plane for drawing.
(3) 2D drawing area This is the area where the tool path is drawn when performing a program check.
The drawing viewpoint can be moved, and the drawing size can be enlarged and
reduced.
Select the zero point to be displayed with following parameter:
#1231 set03/bit4 0:Basic machine coordinate system zero point
1:Workpiece coordinate system zero point
(4) Scale This shows the display range scale. Use Zoom in or Zoom out menu to
change the scale value.
(5) Machining time display This calculates and displays the machining time.
(6) G modal display for check This displays the following modals.
• Absolute/incremental (G90, G91: Group 3)
• Operation mode (G00, G01, G02, G03 etc.: Group 1)
• Tool radius compensation (G40, G41, G42: Group 7)
• Fixed cycle (G80, G81 etc.: Group 9)
(7) Input area This displays details of the key input when setting the scale value and display axis
name.
Press the menu Display range , Display mode keys to display the input area.
I - 307
4. Edit Screen

(8) Currently executed
machining program
Main O10… This displays the device name, program number, sequence number, and block
number currently being executed.
Sub O1234… This displays the sub-program device name, program number, sequence number,
and block number for the sub-program currently being accessed.
(9) Buffer display This displays the contents of the machining program currently being checked.
Menus

This performs an operation search and a check search. C 4.3.1 Checking
Operate
search Select a program to perform a check for from the program file list Continuously
displayed in the pop-up window.
Check This checks the program continuously. B
continu
Check This checks the program per block. B 4.3.2 Checking One
step Block at a Time
Check This resets the program check. C 4.3.3 Cancelling the

reset Program Check
This erases the graphics displayed on the screen. C
Erase Each time this menu is pressed, the graphic data is erased in the
order of rapid traverse and cutting feed.
This changes the graphic drawing display range. C 4.3.5 Changing the
Display Press this menu to display the menu for changing the display mode. Display Range
range This changes the display range and erases the graphic data displayed
on the screen.
This changes the drawing plane. C 4.3.6 Changing the
Press this menu to display the menu for changing the display mode. Display Mode
Display There are 3 types of graphic drawing display mode: 1-plane, 2-plane,
mode and 3-dimension.
This changes the drawing plane and erases the graphic data
displayed on the screen.
All This switches the normal display mode and the full-screen display B 4.3.8 Switching to
display mode. Full-screen Display
Mode
This displays the machining program being checked on the graphic B
Program drawing area.
display This menu can be selected only when the full-screen display mode is
applied.
This changes the program check (3D) display. C 4.4 Program Check (3D)
(This menu does not display if the 3D solid graphic check option is
3D
check disabled.)
This menu cannot be selected while the check is performed or
interrupted.
This sets the viewpoint angle for the 3-dimension display mode. C 4.3.7 Changing the
This changes the viewpoint angle and erases the graphic data Display Angle
Rotate displayed on the screen.
However, this menu cannot be used for other than the 3-dimension
display mode.
The display range (scale and display position) is automatically set C
from the machine movable area. The machine movable area is set
Std with the parameters "#2013 OT-" and "2014 OT+" (software limit).
range
screen is erased.
(Note) The menu 3D check and Operate search keys cannot be selected while the check is performed or
interrupted. Menu can be selected after Check reset is pressed.
I - 308
4. Edit Screen
4.3.1 Checking Continuously
Operation method
(1) Press the main menu Check . The program check screen becomes active.
Press the menu 2D Check when the

program check (3D) appears.
(2) Press the Operate search key. The following menu appears.
The list appears in a pop-up window.
Memory List Sort

card update change
(Ex.) Menu Memory /program) appear in the device name and directory
display columns.
(4) Use the ↑ , ↓ , ½ , ¾ keys to

align the cursor with the target machining
program.
(Note) When the number of characters of directory path (full path) exceeds 48, changing directories
cannot be performed.
(5) Press the INPUT key. The check search is started.

A "Search complete" message appears when the
When setting data exists in the input area, search is completed.
a search is performed in this data. This After performing the search, the device and program
procedure is also used when performing position appear in the current machining program
an NB search. display column.
(Ex.) The list is then closed.
1001/1/2 O1001 N1 B2 The system distinguishes between the presence or
1001.PRG/1/2 O1001.PRG N1 B2 lack of an extension, and therefore due care should be
/1/2 (current O number) N1 B2 taken.
1001//2 O1001 N0 B2
1001/1 O1001 N1 B0
1001 O1001 N0 B0
/1 (current O number) N1 B0
//2 (current O number) N0 B2
I - 309
4. Edit Screen
(6) Press the Check continu key. A program check is executed and that path is drawn.
A "Checking" message appears and the menu is
A block stoppage occurs when performing highlighted.
a program check if the Check continu The check counter display is updated.
or Check step keys are pressed while The check G modal does not display.
performing a continuous check. The machining time is updated.
Furthermore, the program check is
restarted if the Check continu key is
pressed during the block stoppage.
The program check is reset if the

Check reset key is pressed while
performing a continuous check.
A "Program check completed" message appears when

the continuous check is completed.
The Check continu menu highlight returns to
normal.
I - 310
4. Edit Screen
4.3.2 Checking One Block at a Time
Operation method
Press the menu 2D check key when

the program check (3D) appears.
(2) A check search is performed using the

same method as for "4.3.1 Checking
Continuously".
(3) Press the menu Check step . The program check is executed for one block, and a
graphic drawing of the machining program movement
path is made.
The check counter display is updated.
The check G modal display is updated.
<State during one block check>
<State when one block check is completed>
I - 311
4. Edit Screen
(4) Press the menu Check step . The program check is executed for the next block.
The menu returns to normal state.
The program check is continued from the
next block if the Check continu key is
pressed during block stoppage.
4.3.3 Canceling the Program Check
Operation method
(1) Press the menu Check reset . The program check is reset and a "Reset complete"
message appears.
4.3.4 Drawing during a Program Check

During the program check, the machine position (tool center) path is drawn. However, if a radius
compensation is applied on the program being checked, the program path and tool center are drawn.
The colors of the lines displayed during the program check are expressed as follows.
With radius Without radius

Manual feed - -
Rapid traverse Programmed path White -
Tool center move path Blue Blue
Cutting feed Programmed path White -
Tool center move path Green Green
I - 312
4. Edit Screen
4.3.5 Changing the Display Range

The graphic drawing's scale can be enlarged or reduced, and the position moved or centered.
Operation method (Enlarging the and reducing the drawing)
(1) Press the menu Display range . A white frame indicating the display range appears on
the screen.
Zoom Zoom Up Down Left Right Center-

in out ing
(2) Press the menu Zoom In or Zoom out. The size of the white frame can be changed by using
key operations.
To enlarge the drawing size:
Press the menu Zoom In or - key.
To reduce the drawing size:
Press the menu Zoom out or +
key.
A solid-line frame appears with respect to

the original scale when enlarging, and a
dotted-line frame appears when reducing.
(3) Press the INPUT key. The display scale changes.

By changing the display scale, the graphic data
It is also possible to change the display scale by
setting a scale value in the input area.
I - 313
4. Edit Screen
Operation method (Changing the drawing display position)
the screen.

in out ing
(2) Press the Up , Down , Left , Right The cursor () indicating the center of the display and
the frame line move up, down, left and right according
menu or cursor movement keys ↑ , ↓, to the key operations.
←, → .
(3) Press the INPUT key. The display position changes so that the cursor
position () is the center of the area.
By changing the display position, the graphic data
displayed on the screen is erased, however, the scale
value is not changed.
(Note 1) When changing the display range while the 2-plane display mode such as "XY/XZ", the display
range (scale and display position) for the upper and lower areas changes in the same manner.
The white-framed display range in the upper and lower areas simultaneously move to the left/right
when the Left , Right keys are pressed.
The white-framed display range of either upper or lower areas moves up and down when the
Up , Down keys are pressed.
Which frame to be moved up/down can be changed with the page key.
(Note 2) The set displayed position will be held even after the power is turned OFF and ON again.
I - 314
4. Edit Screen
Operation method (Centering)
the screen.

in out ing
(2) Press the Centering . The display position is changed so that the current
machine position appears in the center of the drawing
area.
(Note 1) In the 2-plane display mode such as "XY/XZ", centering is applied for the upper and lower areas.
(Note 2) When the Centering menu key is pressed after the display scale has changed, only the
centering is applied without changing the scale value.
I - 315
4. Edit Screen
4.3.6 Changing the Display Mode

There are three types of graphic drawing mode: 1-plane, 2-plane, and 3-dimension. Press the menu
Display mode key, and by selecting one of the following display mode menus, the axis configuration for
each plane changes, and the menu display returns to normal. It is also possible to change the display mode
by setting the axis name in the input area.
(Note 1) When the display mode is changed, the graphics displayed up to that point are erased.
(Note 2) These set display mode is maintained even after rebooting the machine.
(Note 3) The display mode can be set independently at the trace function and program check function. These
settings are not linked with one another.
(Note 4) The menu axis names XYZ are compatible with the basic axes IJK. X = base axis I, Y = base axis J,
and Z = base axis K.
Display mode menu
Menu Details Type

XY This changes to the 1- plane display mode configured of X-Y. C
The X-axis display in the horizontal axis, and the Y-axis displays in the vertical axis.
YZ This changes to the 1- plane display mode configured of Y-Z. C
The Y-axis display in the horizontal axis, and the Z-axis displays in the vertical axis.
XZ This changes to the 1- plane display mode configured of X-Z. C
The X-axis display in the horizontal axis, and the Z-axis displays in the vertical axis.
XY/XZ Changes to 2-plane display mode composing X-Y, and X-Z. C
The X-axis display in the horizontal axis, and the Y-axis and Z-axis display in the vertical axis.
YX/YZ Changes to 2-plane display mode composing Y-X, and Y-Z. C
The Y-axis display in the horizontal axis, and the X-axis and Z-axis display in the vertical axis.
XYZ This changes to the three-dimensional display mode. C
A cube is displayed on the lower right of the screen.
Changing the display axis name
(1) Set the axis name and press the INPUT XYZ appears the graphic display mode name.
key. There are 3 drawing axes: X, Y, and C.
XYC INPUT
There are three types of display mode: 1- plane, 2- plane, and 3D. An image displays which display mode
is currently selected. The selected axis name displays for the image axis name.
Display example
<1-plane> (XY) <2-plane> (XY/XZ) <3-dimension> (XYZ)
I - 316
4. Edit Screen
4.3.7 Changing the Display Angle

This is used to set the graphic drawing display angle when in 3-dimension display mode.
Press the menu key or cursor keys to rotate the cubic displayed at the screen upper right and press the
INPUT to set.
(Note 1) When the display angle is changed, the graphics displayed up to that point are erased.
(Note 2) The set display angle is maintained even after rebooting the machine.
(Note 3) The display angle can be set independently at the trace function and program check function. These
settings are not linked with one another.
Operation method
(1) Press the menu Rotate . The mode changes to the rotation mode and the
Up Down Left Right
(2) Use the Up , Down , Left , Right Rotate the cubic display in the lower right of the screen
menu to adjust the display angle. using the operation keys.
Z Z
The cursor movement keys ( ↑ , ↓ , X Y
← , → ) can also be used to rotate. Y X
(3) Press the INPUT key. The display angle changes.

By changing the display angle, the graphic data
I - 317
4. Edit Screen
4.3.8 Switching to Full-screen Display Mode
Press the All display menu key to display the program check window on the whole screen. (full-screen
display mode).
All display
menu : ON
All display
menu : OFF
Normal display mode Full-screen display mode
function commonly.
Displaying a program
When pressing the Program display menu key, the contents of the machining program on checking is
displayed on the drawing area.
When pressing the Program display again, the displayed program is erased.
Note that this menu can be used only when the full-screen display mode is selected.
(Note 2) The program display mode is applied to the trace function and program check (2D) function
commonly.
(Note 3) The Program display menu key cannot be selected while the normal display mode is selected.
Program display mode is valid only when the full-screen display mode is selected.
(Note 4) The program display mode is applied commonly to all part systems.
I - 318
4. Edit Screen
4.3.9 Availability of Check Mode with Other Functions

It is important to be aware that certain NC parameters, program commands, and machine operation panel
switches cannot be used while performing a program check.
Function name Remarks

Decimal point programming Both decimal point input type I and II are valid.
Mirror image A mirror image is applied and a check drawing is made at the setting
(Parameters, external input) status prior to starting the check.
Z-axis command cancel Signals are ignored and a check drawing is made.
Interlock Signals are ignored and a check drawing is made.
External deceleration Signals are ignored and a check drawing is made.
Override Signals are ignored and a check drawing is made.
Auto operation pause (feed hold) Signals are ignored and a check drawing is made.
Auto operation start-up (cycle start) “M01 Operation alarm (0112)" occurs if automatic operation is
started up while the check drawing is being made.
Auto-restart The check is completed at M02/M30 and is not restarted.
Manual mode/handle The mode can be changed to manual or handle mode and the
machine can be moved even during the check. However, this is not
reflected to the check drawing position.
F1-digit feed The speed command does not influence the check drawing.
User macro I·II Basic variable calculations, decisions and branch functions are all
enabled.
However, the following functions are ignored, or indefinite values are
input.
Macro interface input/output,
Single block stoppage,
Miscellaneous function complete signal waiting control,
Feed hold, Feedrate override,
G09 enabled/disabled control,
Reading of position information for other than the previous block
end point coordinates
M·S·T·2nd miscellaneous function M·S·T·2nd miscellaneous function command signals commanded by
commands the program during the check are not output. Neither do they display
on the Operation screen etc.
G command modal G modal displays on the modal display screen while the check
drawing is being made.
Tool compensation amount The check drawing is made with the tool compensation amount set
when starting the check drawing.
Workpiece coordinate system offset The check drawing is made with the workpiece coordinate system
amount offset amount set when starting the check drawing. The display data
is not changed when changes are made with G10 or system
variables.
Parameter The setting values when starting the check drawing are used.
Parameters are changed to command values when changing the
parameters using G10.
Optional block skip The setting status when starting the check drawing are used.
I - 319
4. Edit Screen
(Note) Reference position return and start position return

The reference position return command and start position return command are valid, but actual
machine motion (trace display) is partially different from the drawing by program check. As shown in
the figure below, when returning to the reference position via the intermediate point with the G28 or
G30 command, positioning to the intermediate point is done by a straight line and positioning from
there to the reference position is done by each axis independently.
With the G29 command, positioning to the intermediate point is done by each axis independently.
Under program checking, however, positioning is always done by a straight line even when returning
via the intermediate point; this may cause a little difference from the trace display.
X Basic machine coordinate system (G53)
#1
Reference point return (G28)

First reference position
Movement path in
trace mode (G29)
Movement to Movement path in trace mode (G28)

intermediate point
Movement to intermediate point (G29)
Position move with

Intermediate point G29 command
4.3.10 Handling of Variable Commands, Parameter Input by Program, and Compensation Data
Input by Program
If a program check is performed for a machining program for which the variable command data etc. is
rewritten, all data types are treated as shown in the following table after completion.
Saving data before

Data type Explanation
program check
Parameter × The program parameter input commands are
set as actual data.
(The data before the check is not saved.)
Local variable {/× It is possible to return to the status prior to
starting the program check based on the "#1231
Common variable {/×
set03(bit0) " graphic check interchangeable
Workpiece coordinate {/× parameter value.
system offset 0: Returns to original status after check
Tool compensation amount {/× completion
1: Does not return to original status after
check completion
I - 320
4. Edit Screen
4.3.11 Notes for Program Check (2D)
Check function
(1) The check function draws while referring only to the NC internal operation results. Thus, the path is not
drawn for commands requiring machine movement.
(2) Check search and check start are not possible during automatic start or automatic pause. The operation
message "Executing automatic operation" appears.
(3) Operation search is possible for a program with 32 or less file name characters.
(4) Graphic check is not available for MDI program.
Notes for checking (Common for continuous check and check step)
(1) When the menu Zoom in , Zoom out , Display mode , Rotate or Display range key is pressed
while checking, the graphic data is erased, however, the program check is not interrupted.
(2) Drawing is continued even after changing to another screen while checking.
(3) Automatic operation cannot be performed even if the automatic operation button is pressed while
checking. “M01 Operation Alarm (0112)" occurs.
(4) Execute automatic start after the check is completed or after the check is interrupted by pressing the
Check reset .
(5) Refer to "4.3.10 Handling of Variable Commands, Parameter Input by Program, and Compensation Data
Input by Program " for further details on all types of data set in the program while checking.
(6) Checking the program stops if there is a M00/M01 command. However, when executing the M01
command, drawing is stopped regardless of the ON/OFF status of the optional stop switch signal.
(7) When switching part systems during checking, drawing will be erased. When the displayed part system is
undone, check operation will be continued from the previous state (program position before part systems
were switched).
(8) Status during checking (in "Check continu"/in "Check step") is held per part system.
(9) 2D graphic check drawing begins from the actual coordinate value used for the program operation
(coordinate value of the machine position).
(10) The contents of ONB display and buffer display in the check screen during automatic operation are the
contents of the program during automatic operation. The contents of ONB display and buffer display in
the operation screen during check execution are the contents of the program during check execution.
(11) When operation search or check operation ("Check continu" or "Check step") is performed during
program restarting, the operation message "in program restarting" is displayed, and the program will not
be searched or graphically checked.
Notes for ending check
(1) If an M02/M30 command is found, "Program check completed" occurs.

(2) By performing commands such as a check reset or turning the trace display ON, the check mode is exited.
Clear the errors with these operations in the case of a program error. When the NC has been reset while
the check screen is displayed, graphic check will be completed, but the menu for changing from 3D to 2D
graphic check will remain disabled. Press the check reset menu to enable the switching operation.
(3) Check reset is available only for the displayed part systems.
(4) When a NC reset is performed during check operation, all the part systems will be reset. When a part
system not being displayed is in checking and if switching to that part system, check will be executed
from the head of the program.
I - 321
4. Edit Screen
Notes for switching between trace mode and check mode
(1) The checking mode is released when the trace mode becomes ON.
(2) Graphic check (2D) cannot be performed during the trace mode.
(3) When displaying Edit screen during the graphic trace mode, graphic check 3D will be applied regardless
of the previous check type. If the 3D solid check option is not valid, the area of Check tag will be blank.
(4) When trace window is displayed during check, check will be terminated. (This applies for all the part
systems under checking.)
I - 322
4. Edit Screen
Program check (3D) is a function that draws the workpiece shape and tool movement in the cutting process
of the machining program as a solid image without executing automatic operation. The machining program
can be checked with graphic data drawn at a high speed.
This function requires workpiece and tool shape settings.
Program check (3D) can draw a solid image in the basic machine coordinate system or the workpiece
coordinate system.
The coordinate system used to draw can be switched on "Work set" screen.
In the workpiece coordinate system, a solid image is drawn by using the workpiece coordinate system
designated by the program.
(Note 1) The program check (3D) function is an additional specification. The graphic check and 3D solid
graphic check option is required.
(Note 2) When changing the screen to the edit screen, display depends on the previous checking type
(2D/3D). Note that when selecting this screen during graphic trace, 3D solid program check will
apply.
If the 3D solid check option is not valid in this time, the area of Check tag will not be blank.
▅ Normal display (full-screen display mode is OFF)

<Drawing area>
(1) (5)
(2) (6)
(3)
I - 323
4. Edit Screen
▅ Full-screen display (full-screen display mode is ON)

<Drawing area>
(1)
(2) (3)
(5)
(4)
Display items

(1) Check counter This displays the axis counter for check drawing.
As for the counter, the machine position or workpiece coordinate position is displayed
according to setting the drawing coordinate system on "Work set" screen.
As for the axes name, system common axis name ("#1022 axname2") based on the
basic axis name set to "#1026 base_I", "#1027 base_J", and "#1028 base_K" are
displayed.
(Note) When the setting values of #1026 to #1028 have been changed, the changed
values will be reflected in the check counter display when the power is turned
ON again.
(2) 3D drawing area This area is used to display a solid graphic drawing of the workpiece shape and tool
movement during the cutting process in the machining program.
The drawing viewpoint can be moved, and the drawing size can be enlarged and
reduced.
The coordinate system used to draw switches the basic machine coordinate system
or a workpiece coordinate system according to setting the drawing coordinate system
on "Work set" screen.
(3) Machining time display This calculates and displays the time taken for machining.
(4) Check G modal display This displays the following modals:
• Absolute/incremental (G90, G91: Group 3)
• Operation mode (G00, G01, G02, G03 etc.: Group 1)
• Tool radius compensation (G40, G41, G42: Group 7)
• Fixed cycle (G80, G81 etc.: Group 9)
(5) Currently executed
machining program
Main O10… This displays the device name, program No., sequence No., and block No. currently
being executed.
Sub O1234… When sub-program is being executed, the sub-program device name, program No.,
sequence No., and block No. are displayed.
(6) Buffer display This displays the contents of the machining program currently being executed.
I - 324
4. Edit Screen
Menus

This performs an operation search and a check search. C 4.4.1 Checking
Operate
search Select a program to be checked from the program file list displayed in Continuously
the pop-up window.
Check This checks a program continuously. B
continu
Check This checks a program per block. B 4.4.2 Checking One
step Block at a Time
Check This resets a program check. C 4.4.3 Canceling the
reset Program Check
This initializes the workpiece shape. Displays the pre-machining C
Work workpiece shape set at the "Work set" window (workpiece shape
init setting).
At this time, the cross-section status is cancelled.
This enlarges/reduces the displayed workpiece shape. C 4.4.4 Enlarging and
Zoom
Reducing the Workpiece
Shape
Move This moves the displayed workpiece shape. C 4.4.5 Moving the
Workpiece Shape
All This switches the normal display mode and the full-screen display C
display mode.
Rotate This rotates the displayed workpiece shape. C 4.4.6 Rotating the
Workpiece Shape
The scale is automatically set so that the pre-machining workpiece C
Auto
shape set at the "Work set" window (workpiece shape setting) takes
scale
up approximately 90% of the drawing area.
This changes the program check (2D) display. C 4.3 Program Check (2D)
2D
This menu cannot be selected while the check is performed or
check
interrupted.
This enables or disables the interference check. B 4.4.7 Performing an
Colli When the interference check is enabled, if the tool and workpiece Interference Check
check contact each other when performing rapid traverse (G0) movement,
the contact location is drawn in a color highlighting the interference.
Work This sets the workpiece shape used at the solid display. C 4.4.9 Setting the
setting Workpiece Shape
Tool This sets the tool shape used at the solid display. C 4.4.10 Setting the Tool
setting Shape
(Note 1) When the graphic trace mode is entered and automatic operation is running, the menu
Operate search , Check continu , Check step , Check reset cannot be selected and
the 3D solid program check cannot be performed.
Only the 3D solid program check can be performed unless the automatic operation is running.
(Note 2) The menu 2D check , Operate search , Work setting , Tool setting cannot be selected
while the check is performed or interrupted.
I - 325
4. Edit Screen
4.4.1 Checking Continuously
Operation method
Press the menu 3D Check key when

(2) Press the Operate search key. The following menu appears.
The list appears in a pop-up window.
Memory HD Memory DS FD List Sort Close

card update change
(Ex.) Menu Memory /program) appear in the device name and directory
display columns.
(4) Use the ↑ , ↓ , ½ , ¾ keys to

align the cursor with the target machining
program.
(5) Press the INPUT key. The check search is started.

A "Search completed" message appears when the
When setting data exists in the input area, search is completed.
a search is performed in this data. This After performing the search, the function and program
procedure is also used when performing position appear in the current machining program
an NB search. display column.
(Ex.) The list is then closed.
1001/1/2 O1001 N1 B2 The system distinguishes between the presence or
1001.PRG/1/2 O1001 N1 B2 lack of an extension, and therefore due care should be
/1/2 (current O number) N1 B2 taken.
1001//2 O1001 N0 B2
1001/1 O1001 N1 B0
1001 O1001 N0 B0
/1 (current O number) N1 B0
//2 (current O number) N0 B2
I - 326
4. Edit Screen
(6) Press the Check continu key. A program check is performed, and a solid drawing is
made for the cutting process workpiece shape and tool
A block stoppage occurs when performing movement.
a program check if the Check continu A "Checking" message appears and the
or Check step keys are pressed while Check continu menu is highlighted.
performing a continuous check. The check counter display is updated.
Furthermore, the program check is The check G modal does not appear.
restarted if the Check continu key is The machining time is updated.
pressed during the block stoppage.
A "Program check completed" message appears when
The program check is reset if the the continuous check is completed.
Check reset key is pressed while The Check continu menu highlight returns to
performing a continuous check. normal.
4.4.2 Checking One Block at a Time
Operation method
Press the menu 3D check key when

(2) A check search is performed using the

same method as for "4.4.1 Checking
Continuously".
(3) Press the menu Check step . The program check is executed for one block, and a
solid drawing of the workpiece shape and tool
movement during the cutting process is made.
The check counter display is updated.
The check G modal display is updated.
The machining time is updated.
(4) Press the menu Check step . The program check is executed for the next block.
The program check is continued from the

next block if the Check continu key is
pressed during block stoppage.
4.4.3 Canceling the Program Check
Operation method
(1) Press the menu Check reset . The program check is reset and a "Reset complete"
message appears.
I - 327
4. Edit Screen
4.4.4 Enlarging and Reducing the Workpiece Shape
Operation method
(1) Press the menu Zoom . The mode changes to the enlargement/reduction
mode, and the following menu appears.
Zoom Zoom
in out
(2) Press the menu Zoom in . The drawing area center position is set in the center,
and the enlarged workpiece is redisplayed.
To enlarge the drawing:
Press the menu Zoom in or - key.
To reduce the drawing size:
Press the menu Zoom out or + key.
4.4.5 Moving the Workpiece Shape
Operation method
(1) Press the menu Move . The mode changes to the movement mode and the
Up Down Left Right
(2) Use the Up , Down , Left , Right The workpiece shape moved in the designated
keys to adjust the display position. direction is redisplayed.
The cursor movement keys ( ↑ , ↓ ,

← , → ) can also be used for moving.
4.4.6 Rotating the Workpiece Shape
Operation method
(1) Press the menu Rotate . The mode changes to rotation mode and the following
menu appears.
Up Down Left Right
(2) Use the Up , Down , Left , Right The workpiece shape rotated in the designated
keys to adjust the display angle. direction is redisplayed.
The cursor movement keys ( ↑ , ↓ ,

← , → ) can also be used to rotate.
I - 328
4. Edit Screen
4.4.7 Performing an Interference Check

If the tool and workpiece contact when performing rapid traverse (G0) movement, the contact location is
drawn in a color highlighting the interference.
Operation method
(1) Press the menu Colli check . The menu is highlighted.
(2) Press the menu Check step or A program check is performed, and a solid drawing of
the workpiece shape and tool movement during the
Check continu .
cutting process is performed.
A "Checking" message is displayed and the menu
Check step or Check continu key is highlighted.
The workpiece and tool contact, this is drawn in a color
highlighting the interference.
Press the All display menu key to enlarge the program check window (full-screen display mode).
All display
menu : ON
All display
menu : OFF
Normal display mode Full-screen display mode
function commonly.
I - 329
4. Edit Screen
4.4.9 Setting the Workpiece Shape

Press the menu Work setting key to display a pop-up window similar to the following, and set the
workpiece shape used in the solid display.
(2)
(1)
Display items

(1) Workpiece shape setting This sets all workpiece shape items.
area
(2) Guide drawing This displays a material shape guide drawing.
The displayed guide drawing is changed according to the coordinates set on "Work
set" screen.
Menus (the cursor is at CoordinateSystem (drawing coordinate system))

Machine This specifies the coordinate system used to 3D drawing. The name C Setting the drawing
coord and value of the check counter displayed on 3D check screen are coordinate system
switched to the machine position and the workpiece coordinates (CoordinateSystem)
counter position. The default setting is the "Machine coord" (machine
Work position).
coord When "Machine coord" is selected, "All Wk. Coord" (all workpiece
coordinates) is set at "Coord Select" (workpiece coordinate system
selection).
Close
Menus (the cursor is at WorlForm (material shape))

Default This sets the material shape. C "Setting the material
shape The drawings are made as a block when the default shape is selected. shape"
Block

Close
I - 330
4. Edit Screen
Menus (the cursor is at Coord Select (workpiece coordinate system selection))

This draws all workpiece coordinate systems. When the menu is C Selecting the drawn
All wk. selected, "All Wk. Coord" (all workpiece coordinates) is displayed at workpiece coordinate
coord the cursor position. When the drawing coordinate system is "Machine system
coord" (machine coordinate), "All Wk. Coord" is selected. The default
setting is "All Wk. Coord".
This specifies the workpiece coordinate (G54-G59) to the drawn C
Coord coordinate system. The drawn coordinate system is selected from
G54-G59 sub-menu (G54 to G59). If the drawing coordinate system is "Machine
coord", this is displayed in gray and cannot be selected.
This specifies the external workpiece coordinate (G54.1 Pn) to the A
Coord drawn coordinate system type. By inputting P No., the external
G54.1P workpiece coordinate (G54.1 Pn) can be selected to the drawn
coordinate system. If the drawing coordinate system is "Machine
coord", this is displayed in gray and cannot be selected.
Close
Menus (the cursor is at WorkRefPoint(I,J,K) (material basic point), or WorkWidth (material width))

Close
Menus (the cursor is at the WorkColor, MachinedColor, TappedColor, InterferenceColor,

SectionColor in the window)

Default This sets the material color (WorkColor), machining surface color C "Setting the material
color (MachinedColor), tap surface color (TappedColor), interference color"
surface color (InterferenceColor), and cross section color
Gray (SectionColor).
The drawings are made using the following colors when the default
colors are selected.
Red Material color : Gray
Machining surface color : Yellow
Yellow Tap machining surface color : Light blue
Interference surface color : Red
Cross section color : Green
Blue (Note) The tap surface color (TappedColor) of the work shape setting
(Work set) screen is applied when the selected tool is tap.
Therefore, switching of the tap surface color and normal
Green
surface color depends on not G command but the selected
tool. However, even if the selected tool is tap, the tap surface
Light color (TappedColor) of the work shape setting (Work set)
blue
screen is not applied when circular interpolation or helical
interpolation is commanded.
Purple
Pink

Close
I - 331
4. Edit Screen
Setting the drawing coordinate system (CoordinateSystem)

to the drawing coordinate settings column.
(2) Press the menu Work coord. "Work coord" appears at the cursor position.
The cursor moves one place down.
It is also possible to set input values. A guide drawing with workpiece coordinate origin
0 INPUT : Machine coord appears in the guide drawing area.
1 INPUT : Work coord
Selecting the drawn workpiece coordinate system
When the drawing coordinate system is the workpiece coordinate, the drawn coordinate system can be
selected. Only the coordinate system selected here is drawn.
When the drawing coordinate system is the machine coordinate, "All Wk. Coord" (all workpiece
coordinates) is set at "Coord Select" (workpiece coordinate system selection). Therefore,
Coord G54-G59 or Coord G54.1P menu cannot be selected.
(Example) When "Coord G54-G59" is selected

to "Coord Select" column.
(2) Press the menu Coord G54-G59. The sub-menus, which select G54 to G59, are
displayed.
(3) Press the menu G56. "G56" appears at the cursor position.
The sub-menus of the material shape (WorkForm) are
When Return menu is selected, return to
displayed.
Coord Select menu.
Setting the material shape (WorkForm)

to the material shape settings column.
(2) Press the menu Block . "Block" appears at the cursor position.
It is also possible to set input values. A block guide drawing appears in the guide drawing
0 INPUT : Default shape area.
1 INPUT : Block
I - 332
4. Edit Screen
Setting the material basic point (WokRefPoint (I)) and size (WrkWidth (I,J,K))
Enter the material basic point and size. Specify the material basic point with the specified coordinate on
"Work set" screen.
to the material basic point or width (I)
setting column.
(2) Input data. "100.000" appears at the cursor position.

(Ex.) 100 INPUT The cursor moves one place down.
(3) Other basic points and width data are set

in the same way.
(Note 1) The workpiece will not be displayed if two or more size data are "0".
(Note 2) The setting range of the material basic point and width is as follows.
However, the value of less than 0 cannot be set to width.
#1003 #1041 I_inch

iunit 0 (mm) 1 (inch)
B -99999.999 to 99999.999 -9999.9999 to 9999.9999
C -99999.9999 to 99999.9999 -9999.99999 to 9999.99999
D -99999.99999 to 99999.99999 -9999.999999 to 9999.999999
E -99999.999999 to 99999.999999 -9999.9999999 to 9999.9999999
Setting the material color (WorkColor)

to the material color setting column.
(2) Press the material color menu. The cell where the cursor is located appears in gray.
(Ex.) Menu Gray The cursor moves one place down. (The cursor does
not move when at the cross section color.)
It is also possible to set input values.
0 INPUT : Default color
1 INPUT : Gray
2 INPUT : Red
3 INPUT : Yellow
4 INPUT : Blue
5 INPUT : Green
6 INPUT : Light blue
7 INPUT : Purple
8 INPUT : Pink
(3) Other color data is set in the same way.

(Note) The following colors are used if the default colors are designated.
Material color : Gray
Machining surface color : Yellow
Tap machining surface color : Light blue
Interference surface color : Red
Cross section color : Green
I - 333
4. Edit Screen
Difference of drawing by combination of "CoordinateSystem" and "Coord Select"
By combination of the drawing coordinate system (CoordinateSystem) and the workpiece coordinate
system selection (Coord Select), the drawing at 3D check changes as follows.
(Example)
[Parameter] [Machining program]
#8920 = 1 N1 G28 XYZ
[Tool compensation] N2 T1 M6
No.1 : Length 150.000 L wear 0.000 N3 G43 H1
Radius 20.000 R wear 0.000
[Workpiece coordinate] N10 G0 G90 G59 X100. Y100. Z0.
G59 : X 50.000 Y 50.000 Z 0.000 N11 G91 G01 Z-200. F100
G54.1P1 : X 200.000 Y 200.000 Z 0.000 N12 G02 I-15
[Workpiece shape setting] N13 G01 Z200.
Workrefpoint (I,J,K) = (0.000, 0.000, -200.000)
WorkWidth (I,J,K) = (500.000, 500.000, 100.000) N20 G0 G90 G54.1 P1 X200. Y200. Z0.
N21 G91 G01 Z-200. F100
N22 G02 I-15
N23 G01 Z200.
M30
%
Coord
CoordinateSystem Drawing result when 3D check in example
Select
Machine Coord All wk. Arranges the workpiece based
coord on the machine coordinate zero
point.
N12 Draws the tool movement of all
workpiece coordinate systems
N22 on the basic machine coordinate
system.
Basic machine coordinate

system zero point
Work Coord All wk. Arranges the workpiece based
coord zero point G59 on the workpiece coordinate
zero point.
Draws the tool movement of all
N22 workpiece coordinate systems,
considering workpiece
coordinate zero points, G59 and
N12
G54.1P1, to be at the same
position.
zero point G54.1P1
Work Coord G59 Arranges the workpiece based

on the selected workpiece
coordinate zero point.
Only draws the tool movement
of the workpiece coordinate
G59.G54.1P1 is not drawn.
N12
zero point G59
I - 334
4. Edit Screen
4.4.10 Setting the Tool Shape

Press the menu Tool setting key to display a pop-up window similar to the following, and set the tool
shape used in the solid display.
(2)
(1)
(3)
Display items

(1) Tool shape setting area This sets all tool shape items.
(2) Guide drawing This displays a tool shape guide drawing.
(3) Tool clear guidance area This displays a guidance concerning the area of tool clear.
Menus (when the cursor is at the tool number)

This clears the tool shape data where the cursor is located. A "Clearing the tool
Specification method: Tool No. to start/end tool clear number"
(Example) 10/30: Data in the lines of tool No.10 to 30 will be cleared.
Tool 10/E: Data in the lines of tool No.10 and after will be
clear
cleared.
When the INPUT key is pressed without specifying tool No., the
data in the line at the current cursor position will be cleared.
Close
I - 335
4. Edit Screen
Menus (when the cursor is at Kind (tool type))

Default This sets the tool type. C "Setting the tool type"
tool A drill displays if the default tool is selected.
Ball
endmill
Flat
endmill
Drill
Bulnose
endmill
Chamfer
Tap

Close
Menus (when the cursor is at Radius (tool radius), Length (tool length), or ToolData1,2 (shape data)

Close
Menus (when the cursor is at CL (tool color))

Default This sets the tool color. C "Setting the tool color"
color This displays in red if the default color is selected.
Gray
Red
Yellow
Blue
Green
Light
blue
Purple
Pink

Close
I - 336
4. Edit Screen
Registering the tool data
A maximum of 80 tools can be registered.

(1) Use the cursor keys to move the cursor to
the tool number setting. column.
The cursor can be moved freely from the
1st to the 80th line regardless of the
number of tools being registered.
(2) Input the Tool No. "10" appears at the cursor position.
(Ex.) 10 INPUT The cursor moves one place to the right.
(Note 1) Register a new tool data to set the default value for the tool type, tool radius, tool length, and
shape data 1,2, and tool color.
(Note 2) If two or more of the same tool number is registered, the tool shape data that is registered first is
selected.
(Note 3) When an unregistered tool is selected, the previously used tool is used as is.
Clearing the tool data (Clearing tool data for one line at the cursor position)
<When inputting directly>

the tool number setting column.
(2) Input as shown below. The contents of the line where the cursor is located are
0 INPUT all cleared.
The cursor does not move.
<When using menu operations>

the tool number setting column.
(2) Press the menu Tool clear . The menu is highlighted.
(3) Press the INPUT key. Background color of the line at the cursor position is
turned to light blue.
The operation message
"Erase?(Y/N)" is displayed.
(4) Press the Y or INPUT key. The contents of the line where the cursor is located are
all cleared.
Press any key other than Y and Background color of the line at the cursor position is
INPUT to cancel. returned.
The cursor does not move.
The menu highlight is returned to normal.
I - 337
4. Edit Screen
Clearing the tool data (Clearing tool data for multiple lines)
(1) Press the menu Tool clear. The menu is highlighted.
(2) Set the first and last tool No. of the area to The background color of the lines for tool No. 20 to 50
be cleared by dividing by "/" and press the is highlighted in light blue.
INPUT key. The operation message "Erase? (Y/N)" appears.
When the tool data to be cleared does not exist within
20/50 INPUT
the page currently being displayed, the cursor is
moved to the first line of the area to be cleared,
making it the top of the display area.
Specify the last line "E" to make it the end of the
clearance range.
(Example) 10/E
(3) Press the Y or INPUT key. The contents of the line highlighted in light blue are all
cleared.
Press any key other than Y and Background color is returned.
INPUT to cancel. The menu highlight is returned to normal.
(Note 1) A setting error occurs when the specified tool No. does not exist.
(Note 2) A setting error occurs when the specified ending tool No. does not exist in the lower line than the
starting tool No.
(Note 3) When the area to be cleared ranges over 2 pages, tools in the specified area in the second page
and after will be cleared, as well.
(Note 4) When two or more of the same tool Nos. are specified, tool data of the tool number registered
first is cleared.
Setting the tool type (Kind)

the tool type setting column.
(2) Press the tool type menu. "Ball endmill" appears at the cursor position.
(Ex.) Menu Ball endmill The cursor moves one place to the right.
The ball end mill guide drawing (note) appears in the
It is also possible to set input values. guide drawing area.
0 INPUT : Default tool
1 INPUT : Ball end mill
2 INPUT : Flat end mill
3 INPUT : Drill
4 INPUT : Bull nose end mill
5 INPUT : Chamfer
6 INPUT : Tap
(Note) The drill appears in the guide drawing area when the default tool is designated.
I - 338
4. Edit Screen
Tool type guide drawing
1: Ball end mill 2: Flat end mill 3: Drill
4: Bull nose end mill 5: Chamfer 6: Tap
Setting the tool color (CL)
Set the tool color for each tool.

the tool color setting column.
(2) Press the tool color menu. The cell where the cursor is located appears in green.
(Ex.) Menu Green The cursor moves to the tool number column one line
below.
It is also possible to set input values.
0 INPUT : Default color
1 INPUT : Gray
2 INPUT : Red
3 INPUT : Yellow
4 INPUT : Blue
5 INPUT : Green
6 INPUT : Light blue
7 INPUT : Purple
8 INPUT : Pink
(Note) The tool appears in red when the default color is designated.
I - 339
4. Edit Screen
4.4.11 Availability of Check Mode with Other Functions

Refer to "4.3.9 Availability of Check Mode with Other Functions".
4.4.12 Handling of Variable Commands, Parameter Input by Program, and Compensation Data
Input by Program
Refer to "4.3.10 Handling of Variable Commands, Parameter Input by Program, and Compensation Data Input
by Program".
4.4.13 Notes for Program Check (3D)
Check function
(1) The check function draws while referring only to the NC internal operation results. Thus, the path is not
drawn for commands requiring machine movement.
(2) Check search and check start are not possible during automatic start or automatic pause. The operation
message "Executing automatic operation" appears.
(3) Operation search is possible for a program with 32 or less file name characters.
(4) Graphic check is not available for MDI program.
Notes for checking (Common for continuous check and check step)
(1) The drawing is not initialized and the program check is not interrupted even if the menu Zoom ,
Move , or Rotate key is pressed while checking.
(2) Check reset is applied when changing to another screen while checking.
(3) Automatic operation cannot be performed even if the automatic operation button is pressed while
checking. An operation alarm ("Program check mode") occurs.
Execute automatic start after completing the check or after stopping the check by pressing the
Check reset
(4) Refer to "4.3.10 Handling of Variable Commands, Parameter Input by Program, and Compensation Data
Input by Program" for further details on all types of data set in the program while checking.
(5) The program stops if there is a M00/M01 command. However, when executing the M01 command,
drawing is stopped regardless of the ON/OFF status of the optional stop switch signal.
(6) The tool shape is drawn using the value set in "Tool set" window (Radius, Length, ToolData1,2).
As for the tool moving path, select with the parameter "#8920 3D tool Ofs Select", whether the tool
compensation amount (radius dimension/length dimension) in Tool compensation screen is added to the
path or not.
When the compensation amount is added, pay an attention so that the compensation No. during tool
length/radius compensation and T command value is the same number. Failure to observe this could
result in over cutting or insufficient cutting because the tool shape does not match the machine position.
(7) If the following data for new tool is "0" or no setting when changing the tool, the new tool is drawn with the
default setting.
•Type : "Drill" is selected when "Kind" is not set.
•Length : 150mm (5.90 inch) when "Length" is "0".
•Radius : 20mm (0.79 inch) when "Radius" is "0".
•Color : "Red" is selected when "CL” is not set.
(8) When the parameter "8920 3D tool Ofs Select" is set to "0" or "1", tool is drawn with its radius the default
value (20mm) if the tool radius to be displayed is "0" or less.
I - 340
4. Edit Screen
(9) The menu related to graphic function cannot be selected during the automatic operation with the trace
mode ON.
(10) The zero point mark is not drawn.
(11) The contents of ONB display and buffer display in the check screen during automatic operation are the
contents of the program during automatic operation. The contents of ONB display and buffer display in
the operation screen during check execution are the contents of the program during check execution.
(12) When operation search or check operation ("Check continu" or "Check step") is performed during
program restarting, the operation message "in program restarting" is displayed, and the program will not
be searched or graphically checked.
Notes for ending check
(1) If an M02/M30 command is found, "Program check completed" occurs.

(2) The check mode ends when check reset, the trace display is turned ON, etc.
Use these operations to clear the error when a program error occurs.
When the NC has been reset while the check screen is displayed, graphic check will be completed, but
the menu for changing from 2D to 3D graphic check will be remained invalid. Press the Check reset
menu to validate the switching operation.
Tool replacement method
(1) Set the standby tool count in the parameters "#1327 3D ATC type". The tool replacement method with
each parameter is as follows. (Tool replacement commands other than M6 (M22, etc.) are not
supported.)
#1327 3D ATC type 0 1 2

Header section T1; T1;
Machining program
T2;
Machining M6T2; M6T3; M6T1;
process section Drawing by tool T1 Drawing by tool T1 Drawing by tool T1
M6T3; M6TXX; M6T2;

Drawing by tool T2 Drawing by tool T2 Drawing by tool T2
M6TXX; (Note 1) M6; M6T3;

Drawing by tool T3 Drawing by tool T3 Drawing by tool T3
End section M6; M6; M6TXX;
(Note 1) TXX is the T number for the empty pot.
I - 341
4. Edit Screen
Drawing position
(1) Set the drawing position with the parameter "#8920 3D tool Ofs Select".
With the parameter "#8920 3D tool Ofs Select", select which data is used for calculation of the drawing
position (tool center point), the tool compensation amount stored in the NC memory or the data set in the
“Work set” window. In the table below;
"NC memory data" indicates "the compensation amount stored in the NC memory".
"3Ddata" indicates "the data set in the "Tool set" window".
Setting of
Tool shape data used for display Tool center position (Z axis)
#8920
Radius In G43 modal:
0 NC memory data
compensation Machine position - 3Ddata
(Tool measurement
Length In G44 modal:
type I) 3D data
1 Radius In G43 modal:
(Tool measurement compensation Machine position - NC memory data
type II) Length NC memory data In G44 modal:
compensation Machine position + NC memory data
(Note) This setting cannot be used with tool
measurement type I.
(Tool measurement compensation Machine position - 3Ddata
type I) 3D data
Length In G44 modal:
(Tool measurement compensation Machine position - 3Ddata
type II) Length In G44 modal:
3D data
(Note) This setting cannot be used with tool
measurement type I.
(Note 1) As for the 1st and 2nd axis (basic axis I,J) and the 3rd axis (basic axis K) during G49 (tool
compensation cancel mode), the machine position is applied to the drawing position.
(Note 2) In the workpiece coordinate system drawing, "Machine position" in above table means
"Workpiece coordinate position".
I - 342
4. Edit Screen
4.5 Program Input/Output
The machining program can input/output between the NC internal memory and the external input/output
device. The hard disk inside the NC unit is also treated as an external device.
This function applies to the following devices.
(1) Memory (NC internal memory)
(2) HD
(3) Serial
(4) Memory card (front IC card)
(5) DS (compact flash at NC)
(6) Ethernet
(7) FD
(8) Anshin-net server
(Note) In 70 series, only the memory, the serial, the memory card, Ethernet and Anshin-net server can be
used.
<During file transmission>

(1)
(4)
(3)
(2)
<During file setting>
(5)
(6)
(7)
I - 343
4. Edit Screen
Display items

(1) Device, directory, file This sets the device, directory, and file name for which the transmission, compare,
name setting area and erase functions are used.
When the number of characters exceeds the display possible number (directory:63,
file name:42), the excess is not displayed.
(2) Input/compare data This displays data that is being transferred or compared.
display If an error occurs while comparing data, the block for which the error occurred
displays.
(3) Guidance display area This displays the device name shortcut key.
(4) Process progress display This displays the details and data input/output direction for the process currently
section being performed.
(5) Capacity display section This displays the file (machining program) registration count information and memory
(Note 1) capacity information for the selected device.
Number of programs registered
: This displays the file (machining program) registration
count.
Remainder : This displays the remaining file registration count.
This displays only when the memory is selected.
Number of memory characters
: This displays the memory character count.
Remainder : This displays the remaining character count.
(6) List display section This displays the device A or B directory contents list (directory and file name).
File name : This displays the file (machining program) name.
Size : This displays the file size. <DIR> displays in the case of the
directory.
Date/comment : The file comment (max. 17 characters) displays in the case of the
memory device.
The file update data displays in the case of the HD, memory card,
DS, FD, or Ethernet devices.
(7) Input area This displays the input key.
(Note 1) Some items may not be displayed depending on the device.
Device Memory Anshin-net

Memory HD Serial DS Ethernet FD
Display item card server
Number of programs
{ { × { { { { ×
registered
Remainder { × × × × × × ×
Number of memory
{ { × { { {* { ×
characters
Remainder { { × { { × { ×
List { { × { { { { ×
{ : Displayed × : Not displayed
• When the Ethernet parameter "#97*1 Host n no total siz" is set to 1, the number of host memory
characters will not appear.
I - 344
4. Edit Screen
Menus

This sets the device, directory and file name for which input/output A 4.5.2 Selecting a
File
set operations are performed. Device, Directory, and
File
Transfr This copies the file in file setting column A file to file setting column B. A 4.5.3 Transferring a File
A→B (The originally transferred file is not affected.)
Transfr This copies the file in file setting column B file to file setting column A. A
B→A (The originally transferred file is not affected.)
Compare This compares the files in file setting column A and file setting column B 4.5.4 Comparing Files
A:B B. (Compare)
This erases the selected file in file setting column. A 4.5.5 Erasing a File
Erase
This changes the name of the file in file setting column A to that of in A 4.5.6 Changing a File
Rename
A→B file setting column B. Name (Rename)
(Note) The same device must be selected for A and B.
This creates a new directory in the selected file setting column. A 4.5.7 Creating a
Dir
create The directory can be created when HD, memory card, DS or FD is Directory
selected for the device.
Merge This adds the file contents of file setting column B to file setting A 4.5.8 Merging a File
B→A column A. (The file setting column B file is not affected.)
Close
MemCrd The formats the memory card (front IC card). A 4.5.9 Formatting an
format External Device
DS This formats the DS. A
format This menu is only for 700 series.
FD This formats the FD. A
This cancels a warning from network service. C 4.5.14 Sharing
Warning Machining Data
cancel "Canceling a warning
from network service"
This interrupts the process (transfer, compare, etc.) during its C
Stop
execution.
I - 345
4. Edit Screen
4.5.1 Changing the Valid Area

It is necessary to enable the areas including device, directory, and file name in the file setting column A or B
in order to set those items.
Change the display area using the ← , → direction cursor keys or the |← , →| tab keys.
File setting field A is valid. File setting field B is valid.
Changing file setting column B to a valid area (refer to upper right diagram)
(1) Press the → or →| key. File setting column B changes to a valid area.
Changing file setting column A to a valid area (refer to upper left diagram)
(1) Press the ← or |← key. File setting column A changes to a valid area.
I - 346
4. Edit Screen
4.5.2 Selecting a Device, Directory, and File

This section explains the file device, directory, and file name specification methods for the file transfer and
erase commands etc. performed on this screen.
File operation procedure
Select a device where the file Select using the shortcut keys or sub-menu.
subject to the operation exists.
Select a path from the list, or input using the

Specify the directory
keys.
Select a file from the list, or input using the

Specify the file.
keys.
Outline of device, directory, and file name designating methods
Designation Designation method

Device
target file Device Directory File name
NC memory • Machining Select from the Key input in the input
program submenu area, and then INPUT
• User macro -
Designate using the Select from the list
program (Default)
shortcut key.
• Fixed cycle
program
Device other All files Select from the Key input in the input Key input in the input
than the NC submenu area, then INPUT area, and then INPUT
memory Designate using the Select from the list Select from the list
shortcut key.
(1) The device can be selected using the sub-menu or shortcut keys.
(The devices that can be used will differ depending on the specifications.)
(2) One of the following methods can be used to designate the directory (for devices other than the NC
memory) and file name.
• Designate the directory path or file name in the input area and press the INPUT key.
• Move the cursor in the list display section to the target directory or file name and press the
INPUT key.
A wildcard (*) can be used for the file name.
Notes when selecting a file
(1) During directory and file name setting, the designated directory, path or file name will be set, even if it
does not actually exist. This will not cause an error. Note that the previously set directory is overwritten.
(2) When selecting a fixed cycle program, it is necessary to set the basic common parameter "#1166 fixpro".
Furthermore, select "Memory" for the device, and "Program" for the directory.
I - 347
4. Edit Screen
Operation method (Selecting an NC memory program)
(1) Press the M short cut key. The device name changes to "Memory".
"Program" appears in the directory.
(2) Press the menu File set . The NC memory program list and input area appear.
The menu appears as follows.

<First page>
Memory HD Serial Memory DS Ethernet FD List Sort Retn
card update change
<Second page>
Comment Anet Retn
nondisp server
By pressing the operation menu at this point, it is possible to change the device.
When selecting the file name from the list

(3) Move the cursor to the file name to be The selected file name appears.
selected, and fix. The list and input area are cleared, and the screen
↑, ↓, INPUT returns to the original display.
The menu returns to its original display.
When inputting the file name from the input area:

(3) Input the file name. The input file name appears.
10013 INPUT The list and input area are cleared, and the screen
returns to the original display.
The menu returns to its original display.
I - 348
4. Edit Screen
Designating multiple files
A wildcard (*) can be used for the file name.

By using a wildcard, multiple files can be transferred, compared, and erased at one time.
[Ex. 1] When programs 1 to 1000 exist in the NC memory.

Designate "*" in the file name : The target program is "1 to 1000".
Designate "*.*" in the file name : There is no target program.
Designate "1*" in the file name : The target program is "1, 10 to 19, 100 to 199, 1000".
Designate "1*.*" in the file name: There is no target program.
Designate "*1" in the file name : The target program is that where the position of the 1 is "1".
(1, 11, 21, 31, ……101, 111, …….981, 991)
Designate "*1*" in the file name : The target program is all of the programs containing "1".
(1, 10 to 19, 21, 31, ……100 to 199, 201, 210, …….981, 991,1000)
Designate "1*1" in the file name : The target program is "11, 111, 121, 131, 141, 151, 161, 171, 181,
191".
[Ex. 2] When programs 1.PRG to 1000.PRG, and 1 to 1000 exist in the HD.
Designate "*" in the file name : The target program is "1 to 1000".
Designate "*.*" in the file name : The target program is "1.PRG to 1000.PRG".
Designate "1*" in the file name : The target program is "1, 10 to 19, 100 to 199, 1000".
Designate "1*.*" in the file name : The target program is "1.PRG, 10.PRG to 19.PRG, 100.PRG to
199.PRG, 1000.PRG".
Operation method (Selecting a file from a device other than the NC memory)
(1) Press a device selection shortcut key. The device name changes to "HD".
(Example) G The root directory (/) appears in the directory.
(2) Press the menu File set . The HD program list and input area appear.
A menu similar to the following appears.

<First page>
Memory HD Serial Memory DS Ethernet FD List Sort Retn
card update change
<Second page>
Comment Anet Retn
nondisp server
By pressing the operation menu at this time, the device can be changed.
I - 349
4. Edit Screen
When selecting a directory from the list.

(3) Move the cursor to the directory to be The directory selected in the directory column
selected and fix. appears.
↑, ↓, INPUT The contents of the selected directory appear in the
list.
Repeat this operation until the cursor Select ".." to move to one directory above.
arrives at the target directory. There is no change when "." is selected.
Next, refer to operation (4).
When inputting a directory from the input area:

(3) Input the directory path. The input directory path appears in the directory
(Example) /PRG/PRECUT INPUT column.
When selecting the file name from the list.

(4) Move the cursor to the file name to be The file name selected in the file name column
selected and fix. appears.
↑, ↓, INPUT The list and input area are cleared, and the screen
The menu display returns to normal.
When inputting a file name from the input area:

(4) Input the file name. The file name input in the file name column appears.
10013.PRG INPUT The list and input area are cleared, and the screen
The menu display returns to normal.
I - 350
4. Edit Screen
4.5.3 Transferring a File

This section explains the method used to transfer files between different devices, or between the same
device.
Refer to "4.5.2 Selecting a Device, Directory, and File" for details of the device, directory, and file
specification method.
Operation method
(1) Use the ← or |← key to select file setting

column A.
(2) Designate the transfer source device, The designated file displays in file setting column A.
directory and file name. A wildcard "*" can be used for the file name to
designate multiple files.
(3) Use the → or →| key to select file setting

column B.
(4) Designate the transfer destination device, The designated file appears in file setting column B.
directory and file name.
(5) Press the menu Transfr A→B . A message appears to confirm the transfer.
Press the menu Transfr B→A when

transferring from device B to device A.
(6) Press the Y or INPUT key. File transfer is commenced. The process progress
display area displays message indicating that transfer
is in progress, and also indicates the transfer direction.
Furthermore, the data being transferred appears in the
input/comparison data display area of the input data
display column.
A message appears indicating a transfer completion

after transfer has been completed.
! CAUTION
! " ; ", "EOB", "%", and "EOR" are symbols used for explanation. The actual codes for ISO are "CR,
LF" ("LF") and "%".
The programs created on the Edit screen are stored in the NC memory in a "CR, LF" format,
however, the programs created with external devices such as the FD or RS-232C may be stored
in an "LF" format.
! To prevent the influence of data loss and data transformation over the line, always carry out data
comparison after transferring a machining program.
I - 351
4. Edit Screen
Notes (Notes related to transferring in general)
(1) Depending on the type of file, some data cannot be transferred during automatic operation. Do not
transfer during automatic operation.
(2) When the capacity of the transfer destination is reached during file transfer, only the data transferred up
to that point is registered as a file, and an error will occur.
(3) During input to the NC memory or comparison, if the file format size on the NC memory side differs from
the other side file format size (when the maximum number of registrations differs between the NC
memory and the other side), processing is carried out matching the smaller size.
(Ex. 1) If a format size of 200 files is input for a format size of 1000 NC files, 200 files are registered.
(Ex. 2) If a format size of1000 files is input for a format size of 200 NC files, the files up to the 200th file
are registered and an error message appears. (The remaining files are not registered.)
(4) Up to 223 files, including the directory, can be registered in the FD's root directory.
Notes (Notes when transferring machining program files)
(1) For the serial, always set both ends of the "EOR" code at the head and end to feed (NULL). If "EOB" etc.,
is directly after "EOR", the operation may not be executed normally due to the input buffer influence
during the next input operation.
(2) The transfer speed is slower if there are many registrations.
(3) The size of one block of the machining program to be transferred should be 250 characters or less.
(4) When using tape, carry out parity V adjustment to improve the reliability of the tape format. Then use it
with the input/output parameter "Parity V" validated.
(5) When the machine tool builder macro and fixed cycle program are input, change the program type with
the parameter (#1166 fixpro). Also, set the device and directory as follows.
Device: Memory, Directory: Program
(6) Transferring or verifying the multiple files between the external device connected serially and that other
than the serial connection.
(7) With machining program created by the MELDAS500 Series or earlier model, "EOB" is registered as "LF".
However, when these programs are stored in the 700/70 Series NC memory, "EOB" will be converted to
"CR LF", and the number of characters will increase. Thus, when all of the machining programs output
from an MELDAS500 Series or earlier model, having the same specifications as the maximum memory
capacity, are stored in the 700/70 Series NC memory, the memory capacity may be exceeded.
(8) When the file to be transferred (input) is running or in "program restarting" mode, the operation message
"Executing automatic operation" or "Program restarting" is displayed and file will not be transferred
(input).
I - 352
4. Edit Screen
4.5.4 Comparing Files (Compare)

This chapter explains method used compare files after transferring.
Operation method

column A.
(2) Designate the device, directory and file The designated file name appears in file setting
name to be compared. column A.

column B.
(4) Designate the other device, directory and The designated file name appears in file setting
file name to be compared. column B.
(5) Press the menu Compare A:B . The file comparison starts.
The input data and comparison data appear in the
input/comparison data display area.
A message appears when the comparison is
completed.
If a comparison error occurs, the block with the error is
displayed in the comparison data display column on
the screen.
(Note) Files that can be compared are text files only.

Correct outcome will not be obtained through binary file comparison.
I - 353
4. Edit Screen
4.5.5 Erasing a File

This chapter explains the method used to delete files.
Operation method (Deleting a file in file setting column A)

column A.
(2) Designate the device, directory and file The designated file appears in file setting column A.
name to be erased.
(3) Press the menu Erase . A message to confirm the erasing appears.
(4) Press the Y or INPUT key. The file is erased.

A message appears when the erasing is completed.
The number of programs registered, number of
memory characters and remainder reappear.
Press the List update menu to update the list.
(Note) If the file to be erased is running, an error will occur, and the file will not be erased.
Operation method (Deleting a file in file setting column B)
Use the → or →| key to select file setting column B, and designate the device, directory, and file name for file
setting column B. Following this, the operation method is same as for "Deleting a file in file setting column A".
I - 354
4. Edit Screen
4.5.6 Changing a File Name (Rename)

This section explains the method used to change the file name.
(1) Changing a file name

column A.
(2) Designate the device, directory and file The designated file appears in file setting column A.
name before the change.

column B.
(4) Designate the device, directory, and file The designated file appears in file setting column B.
name after the change.
(5) Press the Rename A→B menu.
(6) Press the Y or INPUT key. Renaming of the file starts.

A message appears when the renaming is completed.
(Note 1) Make sure the original and new devices are the same.
(Note 2) If the file to be renamed is running or program restarting, an error will occur, and the name will
not be changed.
(Note 3) If a file that does not exist is designated for the original file, or if an existing file name is
designated for the new file selection, an error occurs, and the name is not changed.
(Note 4) The directory where the file in operation search/check search is stored cannot be renamed. The
operation message "Can't rename designated file" appears.
I - 355
4. Edit Screen
4.5.7 Creating a Directory

This section explains the method used to newly create a directory.
Operation method

column A.
(2) Designate the device The designated device name appears.

The devices that can create a directory are HD, FD,
Memory card and DS.
(3) Select a directory to be newly created from The designated details appear.
the list, or designate by inputting from the
input area.
(4) Set the new directory in the input area and The set directory name appears.
press INPUT key.
(5) Press the Dir create menu. The directory is created.
The directory can also be created in file

setting area B.
(Note1) Up to 223 files, including the directory, can be registered in the FD's root directory.
(Note2) Make sure that the directory path is less than 100 characters. When the path exceeds 100
characters, it cannot be recognized as a path.
I - 356
4. Edit Screen
4.5.8 Merging a File

This section explains the method used to add a file in file setting column B to a file in file setting column A.
Operation method

column A.
(2) Designate the merge destination device, The designated file name appears in file setting
directory, and file name. column A.

column B.
(4) Designate the merge source device, The designated file name appears in file setting
directory, and file name. column B.
(5) Press the menu Merg B→A . A message confirming the merge appears.
(6) Press the Y or INPUT key. The file merge starts.

The data being merged appears in the
input/comparison data display area input data display
column.
Furthermore, a message indicating that merging is
being performed, and an arrow from the merge source
(file setting column B) to the merge destination (file
setting column A) display in the process progress
display area.
A message appears when the merge is completed.

The details of the file in file setting column A will be as
follows when the merge is completed.
(FILE A)
G28 XYZ Details of file in file setting
G90 F800 column A before merge.
G00 X100. Y100.;
(FILE B)
G91 G28 XYZ
F1000; Details of file in file setting
G01 X200. Y200.;
M02; column B before merge.
%
The details of the file in file setting column B do not

change.
(Note 1) If the merge destination file (file in file setting column A) is running, an error will occur, and the
files will not be merged.
(Note 2) The devices that can be merged are the memory, HD, FD, memory card and DS.
I - 357
4. Edit Screen
4.5.9 Formatting an External Device

This section explains the method to format the external devices.
Operation method (Formatting an FD) [700 series only]
(1) Insert a floppy disk in the FD drive, and A message confirming the formatting appears.
press the menu FD format
(2) Press the Y or INPUT key. The FD is formatted.

A message appears when the formatting is completed.
(Note 1) The FD is formatted with FAT (1.44MB).

(Note 2) The volume label is set when formatting the FD.
Operation method (Formatting a memory card)
(1) Press the menu MemCrd format . A message confirming the formatting appears.
(2) Press the Y or INPUT key. The memory card is formatted.

(Note 1) The memory card is formatted with FAT16.

(Note 2) The volume label is set when the memory card is formatted.
Operation method (Formatting a DS) [700 series only]
First, press the menu DS format . The following operations are the same as "Formatting a memory card".
(Note 1) The DS is formatted with FAT16.

(Note 2) Only the DS formatted with FAT16 can be used. The DS with NTFS cannot be used.
(Note 3) As for the DS formatted with NTFS, reformat it with FAT formatted by Windows to use.
(NC cannot convert NTFS partition to FAT formatted.)
(Note 4) The volume label is not set even when the DS is formatted.
4.5.10 List of File Names

There is a directory for each type of data in the NC memory.
The NC memory directory and file name handled on this screen is as follows.
Furthermore, when storing the NC memory file in a device other than the NC memory, be careful not to
change the file extension (.XXX).
Data type NC memory directory path File name

Machining program /PRG/USER (Program No.)
Fixed cycle program /PRG/FIX (Program No.)
I - 358
4. Edit Screen
4.5.11 Edit Lock B and C

This function prohibits editing, erasing, etc. of the machining programs B and C, and protects the machining
programs stored in the NC memory.
Machining program A
1 to 7999
Machining program B
(user standard program)
8000 to 8999
Machining program C Editing Editing prohibited
(machine tool builder custom prohibited by by Edit lock B
program) Edit lock C
9000 to 9999
Machining program A
10000 to 99999999
The operations below in the Edit MDI and the Input/Output screens are influenced by the edit lock setting.
An error will occur if operations that are not possible are attempted.
When the edit lock is valid, processing is executed (except the edit lock target program) by the input/output
function.
{ : Operation possible × : Operation not possible

Edit lock B Edit lock C
Screen Operation Machining program Machining program
A B C A B C
Edit Search { { × { { ×
Edit { × × { { ×
MDI registration { × × { { ×
Edit Transfer { × × { { ×
(Input/Output) Compare { × × { { ×
Copy { × × { { ×
Merge { × × { { ×
Rename { × × { { ×
Erase { × × { { ×
Operation Buffer correction { × × { { ×
(Note) When the multiple part system specification is valid, the machining programs of all the part systems
are protected by edit lock B and C.
I - 359
4. Edit Screen
4.5.12 Program Display Lock C

This function prohibits display and search for machining program C (machine tool builder custom program).
The following influences are received on each screen according to parameter "#1122 pglk_c".
Influences of program display lock parameter on operation screen
#1122 pglk_c
Screen operation 1 (Display:{ Search:×) 2 (Display:× Search:×)
Buffer display of operating The program contents are not displayed. Only "%" is displayed.
program
Display when Program display
highlights on 2D check
full-screen
When the menu Edit was The operation message "Program display lock C" appears.
pressed The window is opened.
When the main menu P corr (When the edit lock B or C is valid, edit lock B or C is given to
was pressed priority.)
Search from the operation The search can be executed. The search cannot be
search window executed.
Search from the restart search The operation message
window "Program display lock C"
Search from the top search appears. The window is not
window (of restart search) closed. The contents of input
area are not cleared.
Influences of program display lock parameter on operation screen
#1122 pglk_c
1 (Display: Search: ) 2(Display: Search: )
Screen operation
The file is automatically opened The program contents are not -
when changing the edit screen displayed. Only "%" is (It is not possible to search, so
(Note 1) displayed. the file is never automatically
opened when changing the
edit screen.)
When the file is opened by the The operation message "Program display lock C" appears.
menu Open. The window is not closed.
(When the edit lock B or C is valid, edit lock B or C is given to
priority.)
When the main menu P corr The program contents are not displayed. Only "%" is displayed.
was pressed
Right side program display
when check main menu is
selected
Search from the operation The search can be executed. The search cannot be
search window of 2D/3D check executed.
The operation message
"Program display lock C"
appears. The window is not
closed.
(Note 1) When changing the edit screen, the file opened immediately before or operation searched/check
searched is automatically opened.
I - 360
4. Edit Screen
4.5.13 Data Protect Keys

The data protect keys can be used to prohibit data setting and erasure. The following three keys are available.
(Their names differ according to the machine tool builder. For further details, refer to the instruction manual
issued by the machine tool builder.)
(1) KEY1: Provides general protection for tool data and protection of the coordinate system preset using
the origin set.
(2) KEY2: Protects user parameters and common variables.
(3) KEY3: Protects the machining program.
Data settings and deletion is stopped if any of the data protection keys is OFF.
Data protection keys CNC data
CNC screen KEY1

Tool data
All data settings KEY2
User parameters
KEY3
Machining program
Machining program protection (KEY3)
When the KEY3 is OFF, the following operations are stopped.
No. Operation details Screen

1 MDI data memory registration Edit
2 Machining program editing Edit
3 New machining program creation Edit
4 Comment setting for programs being registered Edit
5 Machining program registration to memory, verification, input/output Edit
6 Machining program deletion (1 program, all) Edit
7 Comment setting for programs being registered Edit
8 Machining program copy, file name change, merge Edit
9 Machining program buffer correction Operation
(Note 1) If editing or settings, etc. are performed on the screens shown above when KEY3 is OFF, a "Data
protect" message appears.
(Note 2) When the multiple part system specification is valid, editing and input/output of the machining
programs of all the part systems are prohibited by KEY3.
I - 361
4. Edit Screen
4.5.14 Sharing Machining Data

Machining data can be send to/received from Anshin-net server in the call center.
Operation method

column A.
(2) Designate the transfer source device, The designated file appears.

column B.
(4) Press the menu File set . The designated file appears in file setting column B.
(5) Press the menu Anshin net to “Anshin-net server” is displayed as device name.
designate the transfer destination device The file name, unless specified, is as same as the
and file name. name of the originally transferred file.
Only numbers within 10 characters can be used for
a file name.
(6) Press the menu Transfr A→B . A message appears to confirm the transmission of
machining data.
(7) Press the Y or INPUT key. Transmission of machining data starts.

A message appears upon the completion of
transmission.
(Note 1) Neither HD operation nor memory card operation can be performed during file transmission from
HD.
(Note 2) Only one file can be saved on Anshin-net server. The file previously exists on the Anshin-net server
is overwritten.
(Note 3) Anshin-net icon appears in the upper middle of the screen during Anshin-net communications.
(Note 4) When Anshin-net server is specified as device name, the directory button is displayed in gray and
cannot be selected.
I - 362
4. Edit Screen
Receiving machining data from Anshin-net server

column A.
(2) Press the menu File set .
(3) Press the menu Anshin net to “Anshin-net server” as device name and the
designate the transfer source device and designated file name are displayed.
file name.

column B.
(5) Designate the transfer destination device, The designated file appears.
(6) Press the menu Transfr A→B . A message appears to confirm the reception of
machining data.
When the file name is not designated in the file setting
column A, the message “File name not designated for
dev A” appears to indicate the error.
(7) Press the Y or INPUT key. The reception of machining data starts.
A message appears upon the completion of reception.
(Note 1) When the same file name exists in the transfer destination device, an error occurs and the transfer
cannot be executed.
cannot be selected.
I - 363
4. Edit Screen
Erasing machining data on Anshin-net server

column A.
(2) Press the menu File set .
(3) Press the menu Anshin-net to “Anshin-net server”, as device name, and the
designate the file name to erase. designated file name are displayed.
(4) Press the menu Erase A . A message appears to confirm the erasing.
(5) Press the Y or INPUT key. The file will be erased.

A message appears upon the completion of erasing.
Canceling a warning from network service
(1) Press the menu key Warning cancel . The warning message from network service is cleared.
(Note 1) A warning message from network service appears when any error occurs during communications.
(Note 2) NC reset can also clear the warning message from network service.
Notes
(1) Transfer to/from Anshin-net server cannot be interrupted.

(2) Only machining program, except fixed cycle and machine tool builder macro, can be transferred to
Anshin-net server.
(3) Data transfer between Anshin-net server and serial (RS232C) or Ethernet is not available.
(4) The edit screen and the maintenance screen can share machining data. However, the machining data
being transferred to/from either of the screens cannot be shared with the other screen.
(5) Wildcard (*) cannot be used for the file name.
(6) The capacity of machining program for transmission is restricted according to the settings of Anshin-net
server.
I - 364
5. Diagnosis Screens
5.1 System Configuration Screen
The hardware configuration (card name and sub-number), software configuration (software number and
sub-number), and PLC program configuration (file name, file label, and execution type) are displayed in this
screen.
Software configuration
(1)
Hardware configuration
(2)
(3)
I - 365
PLC program configuration
(4)
(4)-a
(4)-b
(4)-c
(4)-d
Display items

(1) Software list This displays a list of the software being used.
(2) NC serial No. This displays the NC model name, serial No, model type, and unit type.
NC TYPE: NC type
MITSUBISHI CNC 7***
MODEL NAME: Model name
FCA730
SERIAL NO.: Serial No.
M7123456789
UNIT NAME: Unit type
FCU7-MU011
(3) Hardware list This displays each hardware name.
70 Series CNC : HN761 CPU card
: HN451 Memory card
EXT : HR751 PLC card (for type A)

(Blank for type B)
RI01[n] : Remote IO unit 1 (n= 0 to 7)
There are up to three channels. The 7th and 8th station of the
RIO3 channel is fixed for use with the handle I/F and is not
displayed.
I - 366

(3) Hardware list
700 Series CNC (Note) : HN115A Main card with LANCPU
: HN081A Power card
: HN116/122 CPU card (Differs between M720, M730, M750)
: HN482/484 Memory card (Differs between M720, M730, M750)
The CNC unit is composed of four PCBs. Bus connections are
used with all cards.
ATT CARD : Currently unused.
EXT : EX891 Back panel
: HR553 Extension unit
: HR577 Extension unit
The extension unit is a hardware option. The PLC high-speed
engine or PROFIBUS card, etc. is connected.
The back panel + up to three cards are displayed.
There are up to three channels. The 7th and 8th station of the
RIO3 channel is fixed for use with the handle I/F and is not
displayed.
(4) PLC ladder file list This displays the file name, file label, execution type for each PLC ladder program.
Use ↑ , ↓ keys to change the pages and refer it.
(a) This displays the registration No. of each PLC program file.
Registration Registration size is max. 32 files.
No. The target file to be executed is max. 20 files.
(b) This displays the file name of PLC program file. (data of GX Developer)
File name Max. 8 characters.
(c) This displays this file label of PLC program file. (data of GX Developer)
File label Max. 32 characters.
(d) This displays the execution type of PLC program.
Execution
type Display Meaning
HIGH High-speed PLC program
MIDDLE Middle-speed PLC program
INTIAL Initial state of PLC program
WAIT Standby PLC program
LOW Low-speed PLC program
(blank) Not the target of the execution.
Menus

S/W This displays the software list. C
config
H/W This displays the hardware list. C

config
Ladder This displays the PLC program list (file name, file label, and execution C
config type
I - 367
5.2 Option Display Screen
5.2 Option Display Screen

The contents of the options registered in the NC are displayed in this screen.
The option items are displayed by name. If all of the options cannot be seen in one screen, the rest of options
can be displayed by pressing the page changeover key.
(1)
Display items

(1) Option items The list of currently usable options are displayed.
As for the currently usable options, the background color is displayed in blue.
The option set when the power supply was turned ON can be currently used.
I - 368
5.3 I/F Diagnosis Screen

The various input/output signals for the PLC (Programmable Logic Controller) control can be displayed and
set in this screen.
These signals can be used in confirmation of the machine sequence operation during PLC development, and
in confirmation and forced output, etc., of the input/output data between the NC and PLC.
(Note) Pay close attention to the sequence operation when using these functions during machine operation.
(3)
(2)
(1)
Display items
(1) Device No. and This displays the data from the device Nos. designated in the setting area in numerical
input/ output order.
signal value The data is displayed as binary (bit units) and hexadecimal values.
(binary/ Individual device Nos. can be displayed separately in the left area and right area.
hexadecimal Select the valid area with theand |← key when →| operations such as display
display) changeover and data setting are carried out.
Each X, Y, M, F, L, SM, TI, TO, TS, TA, STI, STO, STS, STA, CI, CO, CS, CA, D, R,
SB, B, V, SW, SD, W, P, K, and H data is the target data.
(2) Modal output This displays the data and device to carry out modal output.
The details to be defined are set here when carrying out the modal type forced output
of PLC interface signals.
Refer to "5.3.2 Carrying Out Modal Output" for details.
(3) 1-shot output This displays the data and device to carry out one-shot output.
The details to be defined are set here when carrying out the one-shot type forced
output of PLC interface signals.
Refer to "5.3.3 Carrying Out One-shot Output" for details.
I - 369
Menus

Modal This changes the setting area to an input standby status. The signal is A 5.3.2 Carrying out modal
output forcibly output (modal). output
1-shot This changes the setting area to an input standby status. The signal is A 5.3.3 Carrying out
output forcibly output (one-shot). one-shot output
How to read the device No. and display data
A device is an address for classifying a signal handled in the PLC. A device No. is a series of numbers
attached to that device.
Device No. (bit-type)
7 6 5 4 3 2 1 0
X0008 1 0 1 0 0 0 0 1
XF XE XD XC XB XA X9 X8
X0010 0 1 1 0 1 0 1 0 Signal status display

corresponding to each
X17 X16 X15 X14 X13 X12 X11 X10 device No. (I/O)
X0018 0 0 0 0 1 0 0 0
X1F X1E X1D X1C X1B X1A X19 X18
Device No. (word-type)
7 6 5 4 3 2 1 0
High-order
R0010 1 0 1 0 0 0 0 1
8 bits
Low-order
0 1 1 0 1 0 1 0
8 bits
I - 370
List of devices for PLC uses
No. of
Device Device No. Units Details
points
X (*) X0 to X1FFF 8192 1-bit Input signals to the PLC. Machine input, etc.
Y Y0 to Y1FFF 8192 1-bit Output signals to the PLC. Machine output, etc.
M M0 to M10239 10240 1-bit For temporary memory
F F0 to F1023 1024 1-bit For temporary memory. Alarm message interface.
L L0 to L511 512 1-bit Latch relay (Backup memory)
SM (*) SM0 to SM127 128 1-bit Special relay
TI TI0 to TI703 704 1-bit Timer contact
TO TO0 to TO703 704 1-bit Timer output
TS TS0 to TS703 704 16-bit Timer setting value
TA TA0 to TA703 704 16-bit Timer current value
STI STI0 to STI63 64 1-bit Integrated timer contact
STO STO0 to STO63 64 1-bit Integrated timer output
STS STS0 to STS63 64 16-bit Integrated timer setting value
STA STA0 to STA63 64 16-bit Integrated timer current value
CI CI0 to CI255 256 1-bit Counter contact
CO CO0 to CO255 256 1-bit Counter output
CS CS0 to CS255 256 16-bit Counter setting value
CA CA0 to CA255 256 16-bit Counter current value
D D0 to D2047 2048 16-bit Data register
R (*) R0 to R13311 13312 16-bit File register
SB SB0 to SB1FF 512 1-bit MELSEC NET/10 link special relay
B B0 to B1FFF 8192 1-bit MELSEC NET/10 link relay
V V0 to V255 256 1-bit MELSEC NET/10 edge relay
SW SW0 to SW1FF 512 16-bit MELSEC NET/10 link special register
SD SD0 to SD127 128 16-bit MELSEC NET/10 special register
W W0 to W1FFF 8192 16-bit MELSEC NET/10 link register
(Note) The use of devices marked with a * mark in the device column has been determined.
Do not use devices other than those corresponding to the input/output signals with the machine side
(input/output signals of the remote I/O unit), even if it is an undefined vacant device.
I - 371
5.3.1 Displaying the PLC Device Data

The various status signals and register data used in the PLC can be monitored and displayed.
When this screen is first selected, the respective 16-byte amounts of input/output data are displayed from
device "X0000" on the left display area, and from device "Y0000" on the right side.
This screen constantly monitors and displays the PLC signal statuses. Consequently, when signals are
changed in the PLC, the display is changed according to the changes.
Note that because time differences occur between the PLC signal change and the signal display, there may
be a delay in the display. The machine may also not be able to correspond to extremely brief signal changes.
Displaying the data of a arbitrary device No. "X0020"
(1) Press the menu tab key , and

,
select the area to display the data.
(2) Set the device No. (X0020), and press the The device "X0020" appears at the head of the valid
INPUT key. display area.
(Note) When setting the device No., an error will occur if a number exceeding the specifications or an illegal
address is set.
Changing the display with the page keys
The valid area device Nos. change in page units when / is pressed. Changing of the pages stops
within the range of device numbers of which the device has.
(1) Press the key. The data is displayed from the next number
currently displayed.
I - 372
5.3.2 Carrying Out Modal Output

Modal type forced output of PLC interface signals is carried out. Once set, this data is held until cancelled, the
power is turned ON/OFF, or other data is overwritten. There are four sets of devices that modally output. If
this number is exceeded, the previously existing data is overwritten.
Menus used in modal output

This releases the modal output for the device at the cursor position in C "Releasing the modal
Modal the modal output area. output"
clear
The released data is erased from this area.
Modally outputting data "1" to device "X0048"
(1) Press the menu key Modal output . The modal output mode is entered, and the cursor
appears at the modal output area.
(2) Using the ↑ and ↓ keys, move the

cursor to the setting position.
(3) Set the device and data, and press the Modal output is executed, and the cursor disappears.
The data that was in the cursor position is overwritten
INPUT key.
by the input data, and is invalidated.
The modal output mode is cancelled by pressing the
X0048/1 INPUT
key.
(Note 1) The data of the modally output device is displayed in order in the selected area.
This modal output is held until the output is cancelled or the power is turned OFF.
(Note 2) When no data is set (Ex."X0048/","X0048"), the operation message "Setting Data not found" is
displayed.
Releasing the modal output
(1) Press the menu key Modal output . The modal output mode is entered, and the cursor
appears at the modal output area.
(2) Using the ↑ and ↓ keys, move the

cursor to the data to be released.
(3) Press the menu key Modal clear . The data that was in the cursor position is released
from modal output. The "DEV" and "Data" columns
become blank.
The modal output mode is cancelled by pressing the
key.
! Caution
! Pay close attention to the sequence operation when carrying out forced data setting (forced output)
in the I/F diagnosis screen during machine operation.
I - 373
5.3.3 Carrying Out One-shot Output

The one-shot type PLC interface signal forced output is forcibly output only once during the screen operations.
Thus, it may not be possible to confirm the PLC interface signals updated with the PLC on the screen.
One-shot outputting data "1" to device "X0042"
(1) Press the menu key 1-shot output . The one-shot output mode is entered, and the cursor
appears at the one-shot output area.
(2) Set the device and data, press the The input data is overwritten in the one-shot output
INPUT key. area, and is one-shot output. The cursor in the
one-shot output area disappears.
The data of the one-shot output device is displayed in
X0042/1 INPUT
order in the selected area.
The one-shot output mode is cancelled by pressing the
key.
(Note 1) Because the input signal (X, etc.) to the PLC is updated at the head of each PLC cycle, the
machine immediately returns to the normal state, even if one-shot type forced output is carried
out.
(Note 2) When no data is set (Ex.: "X0048/","X0048"), the operation message "Setting Data not found" is
displayed.
! Caution
! Pay close attention to the sequence operation when carrying out forced data setting (forced output)
in the I/F diagnosis screen during mach
I - 374
5.4 Drive Monitor Screen

The diagnosis information from the drive section can be monitored with this screen.
Servo axis unit, spindle unit, power supply unit and synchronous error information is displayed.
(1)
(2)
Display items

(1) Monitoring items This displays each item being monitored. The display is changed using the page
changeover keys.
(2) Data of each axis and unit This displays the data of each axis or each unit being monitored.
I - 375
Menus

Servo This displays the diagnosis information of the servo unit in the data B 5.4.1 Servo axis unit
unit display area. display items
Spindle This displays the diagnosis information of the spindle unit in the data B 5.4.2 Spindle unit
unit display area. display items
Power This displays the diagnosis information of the power supply unit in the B 5.4.3 Display items for
unit data display area. the power supply unit
This monitors the various data related to the auxiliary axis (MR-J2-CT) B 5.4.4 Display items for
servo control. the auxiliary axis unit
AUX
unit The menu appears and operation is possible only when there is one or
more valid auxiliary axes in the auxiliary axis control.
This displays the diagnosis information of the synchronous error in the B 5.4.5 Display items for
Synchro data display area. the synchronous error
error The menu appears and operation is possible only when the
synchronous control axis option is valid.
Alarm This clears the diagnosis information alarm history. A 5.4.6 Clearing the alarm
his clr history
This displays the data for the next four axes. C
Next
axis The menu appears and operation is possible only when diagnosis
information for five or more axes is displayed.
I - 376
5.4.1 Servo Axis Unit Display Items

The various data related to the servo axis (NC axis, PLC axis) is monitored.
To reference, change the display items using the key and key.
The axis name set in the base axis specification parameter "#1022 axname2" appears at the axis name.
Display items

Gain (1/s) This displays the position loop gain.
Feedrate (mm/s)
Position loop gain : Tracking delay error (mm)
Droop (i) The error of the actual machine position to the command position is called droop. This
error is proportional to command speed value.
Speed (r/min) This displays the actual rotation speed of motor.
Feedrate (mm/s) This displays the feedrate detected by the detector mounted on the machine end.
Load current (%) This displays the FB value of the motor current in terms of continuous current during
stalling.
Max current 1 (%) This displays the motor current command in terms of continuous current during
stalling.
An absolute value of the current command peak value sampled after the power ON is
displayed.
stalling.
An absolute value of the current command peak value sampled in most recent 2
seconds is displayed.
Max current 3 (%) This displays the FB value of the motor current in terms of continuous current during
stalling.
An absolute value of the current FB peak value sampled in most recent 2 seconds is
displayed.
Overload (%) This is the data used to monitor the motor overload.
Regen Load (%) This is the data used to monitor the resistance overload state when the resistance
regenerative power supply is connected.
Est disturb torq (%) This displays the estimated disturbance torque in terms of stall rated torque when the
disturbance observer is valid.
I - 377

Max disturb torq (%) This displays the estimated disturbance torque in terms of stall rated torque when the
collision detection function is adjusted.
An absolute value of the estimated disturbance torque peak value sampled in most
recent 2 seconds is displayed.
Load inertia R. (%) This displays the estimated load inertia ratio when the collision detection function is
adjusted.
AFLT frequency (Hz) This displays the present operation frequency of the adaptive filter.
AFLT gain (dB) This displays the present filter depth of the adaptive filter.
LED display This displays the 7-segment LED of the driver.
Alarm This displays the alarms and warnings other than the LED display (displayed on drive
unit side).
Cycle counter (p) This displays the position within one rotation of the encoder detector. The position is
displayed as a grid point value as "0", within one rotation in the range of "0" to "RNG
(movement units) × 1000".
Grid space This displays the grid space for the reference position return. (Command unit)
Grid amnt This displays the distance from the dog-off point to the grid point when the dog-type
reference position return is displayed. The grid mask amount is not included.
(Command unit)
Machine posn This displays the NC basic machine coordinate system position. (Command unit)
Motor end FB This displays the feedback value of the speed detector. (Command unit)
Machine end FB This displays the feedback position of the machine end position detector. (Command
unit)
FB error (i) This displays the error of the motor end FB and machine end FB.
DFB compen amnt (i) This displays the compensation pulse amount during dual feedback control.
Remain command The remaining movement distance of one block is displayed. (Command unit)
Currnt posn (2) The value of the tool compensation amount subtracted from the current position is
displayed. (Command unit)
Man int amt The amount of interrupt movement in the manual absolute OFF state is displayed.
(Command unit)
Abs pos command This displays the coordinates of absolute position excluding the machine error
compensation amount. (Command unit)
Mach err comp val This displays the machine error compensation amount. (Command unit)
Control input 1L This indicates the control signal input from NC.
1H This is used by the system.
:
6L
6H
Control output 1L This indicates the control signal output to NC.
1H This is used by the system.
:
6L
6H
Detection system This displays the detector type symbol of the absolute position detection system.
ES : Semi-closed encoder
EC : Ball screw end encoder
LS : Linear scale
MP : MP scale
ESS : Semi-closed high-speed serial encoder
ECS : Ball screw end high-speed serial encoder
INC : Incremental
I - 378

Power OFF posn This displays the coordinate at NC power OFF in the basic machine coordinate
system. (Command unit)
Power ON posn This displays the coordinate at NC power ON in the basic machine coordinate
system. (Command unit)
Current posn This displays the current coordinate in the basic machine coordinate system.
(Command unit)
R0 This displays the multi-rotation counter value of the detector stored in the memory
during basic point setting.
P0 This displays the position within one rotation of the detector stored in the memory
during basic point setting.
E0 This displays the absolute position error stored in the memory during basic point
setting.
Rn This displays the multi-rotation counter value of the current detector.
Pn This displays the position within one rotation of the detector.
En This displays the absolute position error during NC power OFF.
ABS0 This displays the absolute position reference counter.
ABSn This displays the current absolute position.
MPOS This displays the offset amount of the MP scale when the power is turned ON.
Unit type This displays the servo driver type.
Unit serial No. This displays the servo driver serial No.
Software version This displays the servo side software version.
Control method SEMI : Semi-closed loop
CLOSED : Closed loop
DUAL : Dual feedback
Motor end detector This displays the motor end detector type.
Motor end detect No This displays the motor end detector serial No.
Machine end detector This displays the machine end detector type.
The type is displayed when the control method is CLOSED or DUAL.
* is displayed when the method is SEMI.
Mach. end detect No This displays the machine end detector serial No.
Motor This displays the motor type.
Work time This displays the READY ON work time. (Units: 1hr)
Alarm hist This displays servo alarms that occurred in latest order with the following formats.
1 : Time Time : Work time when the alarm occurred.
1 : Alarm Alarm No. : Number of the servo alarms that occurred.
:
8 : Time
8 : Alarm
Maint hist 1 to 4 This displays the maintenance dates.
Year : One digit
Month : 1 to 9, X (Oct.), Y (Nov.), Z (Dec.)
Maint status This displays the maintenance status.
I - 379
5.4.2 Spindle Unit Display Items

The various data related to the spindle is monitored.
Change the display items using the key and key to refer to the data.
Display items

Gain (1/s) This displays the position loop gain.
Feedrate (mm/s)
Position loop gain : Tracking delay error (mm)
Droop (i) The error of the actual machine position to the command position is called droop. This
error is proportional to command speed value.
Speed (r/min) This displays the actual rotation speed of motor.
Load (%) This displays the motor load.
stalling.
An absolute value of the current command peak value sampled after the power ON is
displayed.
stalling.
An absolute value of the current command peak value sampled in most recent 2
seconds is displayed.
Max current 3 (%) This displays the FB value of the motor current in terms of continuous current during
stalling.
An absolute value of the current FB peak value sampled in most recent 2 seconds is
displayed.
Overload (%) This is the data used to monitor the motor overload.
Regen load (%) This is the data used to monitor the resistance overload state when the resistance
regenerative power supply is connected.
Est disturb torq (%) This displays the estimated disturbance torque in terms of stall rated torque when the
disturbance observer is valid.
Max disturb torq (%) This displays the estimated disturbance torque in terms of stall rated torque when the
collision detection function is adjusted.
An absolute value of the estimated disturbance torque peak value sampled in most
recent 2 seconds is displayed.
Load inertia R. (%) This displays the estimated load inertia ratio when the collision detection function is
adjusted.
I - 380

AFLT frequency (Hz) This displays the current operation frequency of the adaptive filter.
AFLT gain (dB) This displays the current filter depth of the adaptive filter.
LED display This displays the 7-segment LED of the driver.
Alarm This displays the alarms and warnings other than the LED display.
Cycle counter (p) This displays the position within one rotation of the encoder detector. The position is
displayed within one rotation in the range of "0" to "RNG (movement units) × 1000"
using the grid point value as "0".
Grid space This displays the grid space for the reference position return. (Command unit)
Grid amnt This displays the distance from the dog-off point to the grid point when the dog-type
reference position return is displayed. The grid mask amount is not included.
(Command unit)
Machine posn This displays the NC basic machine coordinate system position. (Command unit)
Motor end FB This displays the feedback value of the speed detector. (Command unit)
FB error (i) This displays the error of the motor end FB and machine end FB.
DFB compen amnt (i) This displays the compensation pulse amount during dual feedback control.
Sync tap err (mm) This displays the synchronous error width between the spindle and the drilling axis
during the synchronous tapping. (mm) (Note 1)
(When the parameter "#1041 I_Inch" is set to "1", "Sync tap err (inch)" is displayed.)
Sync tap err (deg) This displays the synchronous error angle between the spindle and the drilling axis
during the synchronous tapping. (degree) (Note 1)
(Note) Synchronous tapping error

This displays the maximum values of the synchronous tapping error that occur during the
synchronous tapping.
The synchronous tapping error means the motor tracking delay for the commanded positions of the
spindle and the tapping axis.
The positive synchronous tapping error means that the tapping axis is delayed responding to the
spindle, and the negative synchronous tapping error means that the spindle is delayed responding to
the tapping axis.
Data name Details

Synchronous tapping • This outputs the data of which absolute value is the largest among
error width (Max value) the synchronous tapping error width (-99999.999 to 99999.999 mm)
during the synchronous tapping modal.
• This data will be initialized to "0" when entering the synchronous
tapping modal or restoring the power. Other than that, the data
continues to display the maximum value.
Synchronous tapping • This outputs the data of which absolute value is the largest among
error angle (Max value) the synchronous tapping error angle (-99999.999 to 99999.999 °)
during the synchronous tapping modal.
• This data will be initialized to "0" when entering the synchronous
tapping modal or restoring the power. Other than that, the data
continues to display the maximum value.
I - 381

Control input 1L This displays the control input signals from the NC.
Control input 1H
Bit Details
0 READY ON command
1 Servo ON command
2
1L
3
4
5
6
7 Alarm reset command
8 Torque limit selection command 1
9 Torque limit selection command 2
A Torque limit selection command 3
1H
B
C
D
E
F
Control input 2H Bit Details

0
1
2
2L 3
4
5
6
7
8
9 Speed observation command valid
A Door closed (controller)
2H B Door closed (all drive units)
C
D
E
F
I - 382


0
1
2
3L 3
4
5
6
7
8
9
A
B
3H C
D
E
F
0
1 Spindle control mode selection command 1, 2, 3
2
4L 3
4
5 Gear selection command 1
6 Gear selection command 2
7
8
9
A
4H B
C M-coil switch command
D L-coil switch command
E Sub-motor selection command
F
I - 383


0
1
2
5L
3
4
5
6
7
8
9
A
5H
B
C
D
E Spindle holding force up
F

0
1
2
6L 3
4
5
6
7
8
9
A
6H B
C
D
E
F
I - 384

Control output 1L This displays the control output signals to the NC.
Control output 1H Bit Details

0 In READY ON
1 In Servo ON
2
1L
3
4
5
6
7 In alarm occurrence
8 In torque limit selection 1
9 In torque limit selection 2
A In torque limit selection 3
1H
B
C In-position
D In torque limitation
E
F In warning occurrence

0 Z-phase passed
1
2
2L 3 In zero speed
4
5
6
7 In external emergency stop
8
9 In speed observation
A Door closed (controller)
2H B Door closed (local drive units)
C
D
E
F
I - 385


0
1
2
3L 3
4
5
6
7
8
9
A
3H B
C
D
E
F

0
1 Spindle control mode selected 1, 2, 3
2
4L 3
4
5 Gear selected 1
6 Gear selected 2
7
8
9
A
4H B
C M-coil switched
D L- coil switched
E Sub-motor selected
F
I - 386


0 Current detection
1 Speed detection
2
5L 3
4
5
6 In coil changeover
7
8 1-amplifire 2-motor switching
9 2nd speed detection
A
5H B
C
D
E In spindle holding force up
F 2nd in-position

0
1
2
6L 3
4
5
6
7
8
9
A
6H B
C
D
E
F
I - 387

Unit type This displays the spindle type.
Unit serial No. This displays the spindle serial No.
Software version This displays the software No. and version on the spindle side.
Motor end detect No This displays the motor end detector serial No.
Mach. end detect No This displays the machine end detector serial No.
Work time This displays the READY ON cumulative time. (Units: 1hr)
1 : Time Time : Work time when the alarm occurred.
1 : Alarm Alarm No. : Number of the servo alarms that occurred.
:
8 : Time
8 : Alarm
Year : One digit
I - 388
5.4.3 Display Items for the Power Supply Unit

The various data related to the power supply is monitored.
Change the display items using the key and key to refer to the data.
Display items

Unit type This displays the power supply unit type.
Unit serial No. This displays the serial No. of the power supply unit.
Software version This displays the software version.
Connected drive This displays the I/F channel No. (mcp_no, smcp_no) of the drive unit connected to
each power supply unit.
Recovery energy(KW) This displays the regenerative power every two seconds. (0 to 999kW)
Pw. sply volt (Vrms) This displays the effective value of the power supply voltage. (0 to 999Vrms)
PN bus voltage (V) This displays PN bus voltage. (0 to 999V)
Min PN bus volt (V) This displays the minimum PN bus voltage after the NC power ON.
(0 to 999V)
Min PN current (%) This displays the bus current when PN bus voltage is at minimum.
(driving: +、regenerative: -) (0 to 999%)
Bus current (%) This displays the bus current. (driving: +、regenerative: -) (0 to 999%)
Max current1 (%) This displays the maximum driving current after the NC power ON.
(0 to 999%)
Max current2 (%) This displays the maximum driving current in most recent 2 seconds.
(0 to 999%)
Max rgn current1(%) This displays the maximum regenerative current after the NC power ON.
(0 to 999%)
Max rgn current2(%) This displays the maximum regenerative current in most recent 2 seconds.
(0 to 999%)
No. of instant stop This displays the number of instantaneous stop exceeding 1 cycle of the power.
(0 to 9999 times)
Work time This displays the READY ON cumulative time. (Units: 1hr)
I - 389

1 : Time Time : Work time when the alarm occurred
1 : Alarm Alarm No. : Number of the servo alarms that occurred
:
8 : Time
8 : Alarm
Year : One digit
I - 390
5.4.4 Display Items for the Auxiliary Axis Unit [700 series only]
"Auxiliary axis unit" appears only when there is one or more valid auxiliary axis. (Base common parameter
"#1044 auxno" is "1" or more).
The various data related to the auxiliary axis (MR-J2-CT) servo control is monitored.
For reference, change the display items using the key and key.
Data for the number of axes (up to six) set with the base common parameter "#1044 auxno (No. of connected
MR-J2-CT units)" is displayed.
Display items

Droop (i) The error of the actual machine position to the commanded position is called droop.
This difference is displayed.
Speed (r/min) This displays the actual rotation speed of the motor.
Load current (%) This displays the continuous executable load torque. This is 100% when the constant
torque is generated.
Max current 1 (%) This displays the commanded torque.
Max current 2 (%) This displays the maximum generation torque of the commanded torque.
Motor load (%) This displays the rate of the load torque to the tolerable load torque as a percentage.
Regen load (%) This displays the rate of the regenerative power to the tolerable regenerative power
as a percentage.
Alarm 1 to 4 This displays the system alarm, servo alarm, system warning, servo warming,
operation alarm No. and alarm information.
Current station No. This displays the number of the currently stopped station.
Current posn This displays the coordinate of current position. (Unit: °)
Inst station No. This displays the commanded station number for automatic operation, or the nearest
station number to be stopped at for manual operation.
Inst posn This displays the coordinate position corresponding to the target station number.
(Unit: °)
I - 391

Posn con gain 1 This displays the position control gain 1.
Speed con gain 1 This displays the speed control gain 1.
Posn con gain 2 This displays the position control gain 2.
Speed con gain 2 This displays the speed control gain 2.
Speed int comp This displays the speed integral compensation value.
Load inertia This displays the estimated motor shaft conversion load inertia ratio value in respect
to the motor's rotor inertia.
Unit type This is the unit type.
Software version This is the servo drive unit software version.
Motor type This is the motor type.
Unit serial No. This displays the unit serial No.
Alarm hist Alarm history : Alarm number
1 : No. Alarm history : Alarm details information
1 : State
:
6 : No.
6 : State
I - 392
5.4.5 Display Items for the Synchronous Error

The "Synchronous error" appears only when the synchronous control axis option is valid.
The various data related to the synchronous error is monitored.
Display items

Slave axis This displays the slave axis name which is controlled following the master axis.
The axis name corresponding to the axis No. set in the axis specification parameter
"#1068 slavno (slave axis No.)" is displayed.
The name set in the base axis specification parameter "#1022 axname2 (2nd axis
name)" is displayed for the slave axis.
Command error This is the deviation of the slave axis machine position in respect to the master axis.
The error of the commanded position to the servo control section before pitch error
compensation, relative position compensation and backlash compensation is
displayed.
If this error occurs, the parameters that should be the same for the synchronous axes
are different.
Command error = Command s - command m -∆
Command s : Slave axis commanded position
Command m : Master axis commanded position
∆ : Command s - command m at start of synchronous control
FB error This is the deviation of the slave axis feedback position in respect to the feedback
position from the master axis servomotor. The actual error of the machine position is
displayed. The synchronous error check is carried out on this error.
FB error = FBs - FBm - ∆
FBs : Slave axis feedback position
FBm : Master axis feedback position
∆ : FBs - FBm at start of synchronous control
FB error MAX1 This displays the maximum FB error after the start of the synchronous control.
FB error MAX2 This displays the maximum FB error approx. every 30 seconds after the start of the
synchronous control.
Machine posn This displays the commanded machine position for the master axis.
I - 393
5.4.6 Clearing the Alarm History
Operation method
(1) Press the menu Servo unit or

Spindle unit .
(2) Using the menu Next axis , tab keys

and , select the axis (device) from
which to clear the alarm history.
(3) Press the menu Alarm his clr . The menu is highlighted, and a message appears to
confirm the erasing.
The alarm history1: Time appears at the head.
(4) Press the Y key. The alarm history data for the selected axis (device) is
cleared to zero.
I - 394
5.5 NC Memory Diagnosis Screen (NC Memory Diagn Screen)

The NC internal data can be displayed and rewritten on the screen. The custom API library's NC data
read/write interface is used to display and rewrite the NC's internal data. The contents of the NC data can be
displayed by designating the part system No., section No., sub-section No. and axis No. on this screen.
(1)
(2)
(3)
Display items

(1) Index No. This displays the registration No. of the NC memory data. When one of the "2. Data
contents" is set, the number is highlighted indicating that the normal display of the
data contents has stopped.
(2) Data contents Part system No.:
Designate the part system No. Designate "0" to designate the data common for the
part systems.
Section/sub-section/axis:
Designate the section No., sub-section No. and axis No. of the data to be set and
displayed. The setting format is, section No./sub-section No./axis No.
(Note) The axis No. "1" is handled as the first axis. Designate "0" for the data
which does not require an axis designation.
(3) Memory data This displays the contents of the data.
I - 395
Menus

Line This erases the information in the line where the cursor is. (One entire C
clear line becomes blank.) The cursor does not move at this time.
The contents of the set address data (Part system No, C 5.5.1 Writing/Reading
Data Section/sub-section/axis) for all the lines are constantly displayed. the Data Using the NC
read The Index No. highlight (indicating data is being set) is released. Data Designation
The cursor appears in "Part system No" of that line.
This writes the data (Note) in the setting area to the NC memory A
indicated by address data at the cursor position.
Data
write The Data No. highlight (indicating data is being set) is released, and
constant display is started.
After writing, the cursor moves to "Part system No" of the next line.
Based on the data of the address data where the cursor is, this C
Subsect displays the continuous data to which the sub-section No. has been
continu added to the address data from the line where the cursor is.
The cursor moves to "Part system No " of that line.
Based on the data of the address data where the cursor is, this C
Axis displays the continuous data to which the axis No. has been added to
continu the address data from the line where the cursor is.
The cursor moves to "Part system No " of that line.
(Note) Decimal, hexadecimal, floating point data and character string data writing is possible.
Note that hexadecimal, floating point data and character strings may not be settable depending on the
data.
Decimal : Integers without decimal points ....... (Example) -1234
Hexadecimal : An "H" is necessary at the end........ (Example) 1234H
Floating point data : Data with a decimal point ................ (Example) -12.3
Character string data : Character string ............................... (Example) X
I - 396
5.5.1 Writing/Reading the Data Using the NC Data Designation

When reading the Process parameter "#8007 Auto corner override", the following data is set.
(Example) Part system No. : 1
Section No. : 126
Sub-section No. : 8007
Axis name : 0
Setting the data
(1) Using the menu cursor keys, move the The cursor moves to the "Part system No." position.
cursor to the "Part system No." position.
(2) Set the part system No. The index No. is highlighted, and the set value is
displayed.
1 INPUT The cursor moves to the right item position.
(3) Separate the section No., sub-section No., The set value appears.
axis No. with a "/", and set. The cursor moves to the right item position.
126/8007/0 INPUT
(4) Press the menu key Data write .
(5) Set the data, and press the INPUT key. Write processing is executed.
The Index No. highlight returns to normal.
Reading the data
(1) Set the part system No., section No.,

sub-section No., axis No. in the same way
as step “Setting the data”.
(2) Press the menu key Data read . The index No. highlight is released, and the normal
display of the memory data starts.
The data format (data size, display format) of the data
displayed in the memory data differs according to the
data type to be displayed.
(Note) The cursor is constantly displayed. Using the cursor keys, the cursor can be moved to the part system
No. area, section/sub-section/axis area.
I - 397
5.6 Alarm Screen
5.6 Alarm Screen

A list of currently occurring alarms or messages can be displayed on this screen.
The displayed messages include the NC alarms, stop codes, alarm messages, operator messages, etc.
A history of alarm information can be displayed also.
NC message
(1)
(2)
PLC message
(3)
(4)
I - 398
5.6 Alarm Screen
Display items

(1) NC alarm This displays the operation alarms, program errors, MCP alarms, servo alarms,
system alarms, etc.
Up to 10 messages are displayed in order of priority.
(2) Stop code This displays the automatic operation status or stop status during automatic
operation.
Up to 4 messages are displayed in order of priority.
(3) Alarm message Using the PLC programs, this displays messages such as details of machine
abnormalities.
Up to 4 messages are displayed.
(4) Operator message Using the PLC programs, this displays operator information messages.
Macro alarm messages are also displayed in this field.
Up to 4 messages are displayed.
Message display colors
The messages are color-coded in the following manner.

Message type Character color Background color
NC message Alarm White Red
Warning Black Yellow
Stop code Black Yellow
Alarm message White Red
Operator message Black Yellow
Axis name display
The axis name is displayed in messages for each axis. The axis name is displayed as shown below
according to the axis type.
Axis type Axis name display Display example Remarks
NC axis Control axis name XYZ If the same message occurs for each part system,
(Name of axis in part several NC axes are displayed together.
system)
Spindle 'S' + spindle No. S1S2 If the same message occurs, several spindles are
displayed together.
PLC axis 'P' + PLC axis No. P1P2 If the same message occurs, several PLC axes are
displayed together.
Auxiliary axis 'A' + auxiliary axis No. A1A2 If the same message occurs, several auxiliary axes
are displayed together.
If the same message occurs for different axis types, they will appear as separate messages.
Part system display
The part system name is also displayed if the message is output for each part system. The part system name
set in "#1169 system name" is displayed. The part system name does not appear for the 1-part system.
I - 399
5.6 Alarm Screen
5.6.1 Alarm History

When an alarm occurs, the alarm information is recorded. When the NC power is ON, an alarm is
automatically recorded in alarm history. Alarm information is recorded from the latest alarm to 512. Alarm
information recorded in the history is NC message and a stop code displayed on "NC message" screen. The
range etc. of record are shown as follows.
Record condition ：When an alarm occurs (Up to five at the same time)
With multi-part system, 1st part system is given priority and recorded.
(Following 2nd part system, 3rd part system...)
Number of history ：512 alarms (Whole)
Range of record ：NC alarm (alarm, warning), stop code
I - 400
5.6 Alarm Screen
Menus

This displays the first page of the alarm history. B
The history sequentially displays 16 alarms per page from the latest
alarm. If there are two or more NC alarms of same day and time, the
Alarm alarms are sequentially displayed from the alarm and warning of 1st
history
part system. Page is changed by , and older histories are
displayed. Page is changed by , and newer histories are
displayed.
The data collection of the alarm history is started. The operation C
message "The collection begin? (Y/N)" appears. When the Y or
History INPUT key is pressed, the data collection is started after the operation
start
message "The collection begin" appears. Press the N or other than
INPUT key when the data collection will be not started/restarted.
The data collection of the alarm history is stopped. The operation C
message "The collection stop? (Y/N)" appears. When the Y or INPUT
History
stop key is pressed, the data collection is started after the operation
message " The collection stop" appears. Press the N or other than
INPUT key when the data collection will be not stopped.
The alarm information of history is updated. C
History When the history is updated, the page with latest alarm information
update (first page) is displayed. The history is updated even if changing to
another screen, and returning to the alarm history screen.
The alarm information of history is cleared. The operation message C
"Execute the collection data clear?(Y/N)" appears. When the Y or
History
clear INPUT key is pressed, the alarm information of history is cleared after
the operation message "Data clear complete" appears. The first page
is displayed when the history is cleared.
(Note 1) History start, History stop, History update and History clear menus are valid when the alarm history
function is valid and Alarm history menu is selected.
(Note 2) When the alarm history function is used for the first time, clear the alarm history contents by
pressing History clear menu. Unnecessary data may be recorded in the alarm history.
I - 401
5.7 Self Diagnosis Screen

The H/W state and NC operation state can be confirmed on this screen.
(1) (3)
(2)
Display items

(1) H/W state This displays H/W state of NC unit and display unit.
(common for part As for the NC unit, the contents are as follows.
systems) Display item Details
NC
Battery vol state This displays the current state of the battery voltage as
0 to 3 below.
Condition Classification
0 (normal state) --
1 (battery drop) Cautions (gray)
2 (detector error) Warning (yellow)
3 (no battery)
used years This displays approximate time of the battery used from
the last replacement.
Recommended battery use (5 Warning (yellow)
years)
≤ Time for the battery used
NC :Temp This displays the current temperature of the control
unit.
-8°C<Control unit temp.≤-3°C Cautions (gray)
63°C≤ Control unit temp.<68°C
Control unit temp.≤-8°C Warning (yellow)
68°C≤ Control unit temp.
:Fan rev This displays the current fan rotation speed of the
control unit.
Fan rot. speed ≤ 4000 r/min Warning (yellow)
(Continues to the next page)
I - 402

(Continued from the Communication between NC unit and display unit
previous page) Servo comm err Num1 This displays the count of occurrence for "Y02
SV commu er: Recv frame No. 0051 xx04" after
the power ON.
Acc1 This displays the cumulated count of
occurrence for " Y02 SV commu er: Recv frame
0051 xx04".
Press the Servo clear menu to clear the
cumulated count to "0".
Servo comm err Num2 This displays the count of occurrence for "Y02
SV commu er: Data ID error 0051 xx03" after
the power ON.
Acc2 This displays the cumulated count of
occurrence for "Y02 SV commu er: Data ID
error 0051 xx03".
Press the Servo clear menu to clear the
RIO channel/station1 This displays the Channel No./Station No. of
occurrence for continuous error after the power
ON.
retry count max1 This displays the maximum value of the
continuous error after the power ON.
RIO channel/station2 This displays the Channel No./Station No. held
even if the power OFF.
Press the RIO clear menu to clear the
Channel No./Station No. to "0/0".
retry count max2 This displays the count held even if the power
OFF.
Press the RIO clear menu to clear the count
to "0".
Ether comm err Num This displays the count of occurrence for "Ether
communication error" after the power ON.
Acc This displays the cumulated count of
occurrence for " Ether communication error ".
Press the Ether clear menu to clear the
I - 403

(2) Operation state This displays the state when the operation seems to be stopped in spite that the
(Depends on part system) alarm does not occur. The following state can be confirmed.
State Details
In-position This displays "1" (in-position state) when the following
conditions are satisfied for even one axis.
• No acceleration/deceleration delay for all axes
• Within the in-position width set in the parameter for all axes
Interlock(+) When the auto interlock +n-th axis signal or the manual
interlock +n-th axis signal is OFF, "1" appears for the n-th axis.
（Explanation of the display） oooooo1o
8th axis … 1st axis

In the above case, the 2nd axis is interlocked.
Even when the number of usable axes is less than 8 in 1 part
system, this displays 8 axes fixed.
Interlock(-) When the auto interlock -n-th axis signal or the manual
interlock -n-th axis signal is OFF, "1" appears for the n-th axis.
The explanation of the display is same as for the "Interlock
(+)".
ExtDcc (+) When the control axis is moving in (+) direction, "1" appears
for the axis if the external deceleration speed is valid, and the
feedrate is clamped, exceeding the set value of the external
deceleration speed.
（Explanation of the display） ooooo1o1
8th axis … 1st axis

In the above case, the 1st axis and the 3rd axis are in external
deceleration speed.
Even when the number of usable axes is less than 8 in 1 part
system, this displays 8 axes fixed.
ExtDcc (-) When the control axis is moving in (-) direction, "1" appears
for the axis if the external deceleration speed is valid, and the
feedrate is clamped, exceeding the set value of the external
deceleration speed.
The explanation of the display is same as for the "ExtDcc" (+).
(3) Credit system This displays the valid term by the credit system when the credit system is valid.
This does not display when the credit system specification is invalid.
I - 404
Menus

Servo This clears the cumulated count of the servo communication error 1 A Clearing the cumulated
clear and 2 to "0". counter to zero
RIO This clears the cumulated count of the RIO communication error to A
clear "0".
Ether This clears the cumulated count of the Ether communication error to A
clear "0".
Battery This clears the time the battery has been used to "0". A
clear
Clearing the cumulated counter to zero
(Example) Clearing the cumulated count of the servo communication error

(1) Press the menu Servo clear . A confirmation message will be displayed.
(2) Press Y or INPUT . The cumulated count of the servo communication error
1 and 2 will be cleared to "0".
When other keys are pressed, it will not clear to "0".
This also applies to RIO clear , Ether clear and Battery clear menu.
When using the multi-part system specification, switch the displayed part system by Next system menu or
the part system switching key $⇔$ .
I - 405
5.8 Data Sampling Screen

Sampling start/stop, sampling state display, setting the sampling parameters necessary for sampling are
performed in the data sampling screen. The NC internal data (speed output from NC to the drive unit, or
feedback data from the drive unit, etc.) can be sampled.
Also, the sampling data can be output externally on the I/O screen under the [Mainte] tag.
Sampling specifications
• Sampling cycle : 1.7ms * magnification
• Number of sampled axes : 1 to 20 axes
(Servo axis 1 to 16 + Spindle 1 to 4)
• Number of sampling channels : 1 to 8 points
• Number of sampled data items : Max. 1,310,720 points
(Note 1) The maximum number of sampled data items is the total number of data. When the number of
sampled channels is increased, the number of data per channel will decrease.
(1) (2)
(3)
(4)
Display items

(1) State This displays the current sampling status.
(The displays, "Sampling" and "Trigger wait" are highlighted.)
Display State
Sampling Sampling is being executed.
Sampling stop Sampling is not being executed, or the sampling process has
completed.
Trigger wait When the "Start condition" is not set to "0" (manual start), this
indicates a state waiting for the sampling to start, detecting
the trigger, after the menu Samp start is pressed.
I - 406

(2) Maximum data This displays the maximum number of data possible for sampling.
Normally, the number of data calculated from the setting value of "Upper limit" is displayed.
The maximum number is 50% of the DRAM available memory.
(3) Sampling counter This displays the position of the sampling buffer during the sampling process.
When the sampling buffer is valid, the head of the buffer can be seen with the value of the
counter at the end of sampling.
Sampling buffer
0
1
:
n-1 End of buffer (newest data)
Sampling counter (n)→ n Head of buffer (oldest data)
:
(4) Sampling parameter This displays and sets the parameters necessary for sampling.
Menus

This starts sampling. This menu cannot be selected under the C
"Sampling" state. When the trigger is set (the "Start condition" is not
set to "0"), the state will be "Trigger wait" until the trigger is detected.
Samp The sampling will not stop even if transferred to another screen during
start sampling.
If this menu is pressed when the parameter "#1224 aux08/bit0" is set
to "0", the operation message "Can't start sampling" is displayed, and
the operation will not start.
Samp This stops sampling, and the state will be "sampling stop". C
end The menu Samp start can be selected.
Sampling parameter
Parameter Details Setting range (unit)

Sampling cycle Set the sampling cycle. 1 to 255
Cycle = 1.7ms ∗ setting value
(Example) When the setting value is 1: 1.7ms cycle
When the setting value is 2: 3.5ms cycle
Sampling channel Set the number of sampling channel. 1 to 8
(Note) The sampling buffer will be divided by the set
number of channels. When the number of sampling
channels is increased, the number of data per
channel will decrease.
Upper limit Set the capacity of the buffer to be used for sampling. 0 to 1279
Buffer capacity = (setting value + 1) ∗ 1024 items
(Note) When the setting value is 0: 1024 items
When the setting value is 1: 2048 items
I - 407

Start condition Select the condition for starting sampling. 0 to 4
0 Manual start
Sampling starts when Smp start menu is
pressed.
1 Variable No.
Sampling starts when the variable set in "Variable
No." is 0 or a value other than null. (Note 2)
2 PLC device
Sampling starts at the rising edge of the signal set
in "PLC device". (Note3)
3 Address condition, true
Sampling starts when "Address", "Data" and "Data
mask" conditions are true. (Note1)
4 Address condition, false
Sampling starts when "Address", "Data" and "Data
mask" conditions are false. (Note1)
Output form Select the data format when outputting the sampling data in text 0，1
style.
0 Outputs in decimal figure
1 Outputs in hexadecimal figure with 8 digits
(Note 1) When "Output form" is set to "1", and "#1004 ctlrunit" is
"E (1nano)", the data larger than 1m will not be output
correctly. When the output data exceeds 1m, the
low-order 32bits of the sampling data will be output.
(Note 2) Refer to the section "5.8.2 Outputting sampling data" for
details on sampling data output.
Address1 Set the sampling address. -
: (a) Index No. method
Address8 The index No. is fixed regardless of the axis configuration.
The low-order six digits of the address are explained below.
(If the high-order two digits are not set, the setting will be
interpreted as 00.)
Setting range (Index No.)

Servo axis 1stAX 2ndAX ··· 16thAX
Feedback position 000100 000200 ··· 000F00
Commanded position 000101 000201 ··· 000F01
Spindle 1stSP 2ndSP ··· 4thSP

Feedback position 010000 020000 ··· 040000
Commanded position 010001 020001 ··· 040001
Examples of setting for each purpose are shown below.

• Synchronized tapping setting:
3rd servo axis FB (000300) - 1st spindle FB (010000)
• High-accuracy setting (roundness):
1st servo axis FB (000100) - 2nd servo axis FB (000200)
• Spindle synchronization setting:
1st spindle FB (010000) - 2nd spindle FB (020000)
I - 408

Adr1 output unit Set output unit for the sampling data of the each address. 0,B,C,D,E,S
:
Adr8 output unit 0 No unit conversion
B Outputs in micrometre
C Outputs in sub-micrometre
D Outputs in 10 nanometre
E Outputs in 1 nanometre
S Outputs in conventional interchangeable pulse of
the spindle
(Note) For other than "0", set only data that internally complies
with "#1004 ctrlunit (control unit)".
However, this does not apply if the "address1 to 8" is set in
the index No.method.
Process Form Set the sampling process type. 0 to 2
0 One-shot
The sampling stops when buffer is full.
1 Repeat valid
After the process ends (the buffer is full), the
"Trigger wait" state will be entered again.
2 Sampling buffer valid
Sampling is executed as a ring buffer.
(Note) If a value other than "0" is set, the "End condition" must
also be set. If not, the sampling process will not end until it
is forcibly ended.
End condition Select the condition for ending the sampling process. (Note 4) 0 to 4
0 Sampling completed
When the buffer is full, the sampling ends.
1 Variable No.
Sampling ends when the variable set in "variable
No." is 0 or a value other than null (Note 2)
2 PLC device
Sampling ends at the rising edge of the signal set in
"PLC device". (Note 3)
3 Address condition, true
Sampling ends when "address", "data" and "data
mask" conditions are true. (Note 1)
4 Address condition, false
Sampling ends when "address", "data" and "data
mask" conditions are false. (Note 1)
I - 409

Variable No. This sets the variable No. that functions as the start/end trigger. 0 to 999
If a number that does not exist is input, an error will occur.
0 System variable (#1299)

Other Designated common variable
than 0 (#100 or more, #500 or more)
(Note) If both "Start condition" and "End condition" are set to other
than "1" (variable No.), the value will be ignored even if set.
PLC device This sets the PLC device that functions as the start/end trigger. (*)X0000 to (*)X1FFF
When "∗" is added at the head, the device will be a b contact. (*)Y0000 to (*)Y1FFF
If a device that does not exist is input or the device No. is not
within the setting range, an error will occur.
0 Data sampling trigger signal (Y72C)

Other Designated device
than 0
than "2" (PLC device), the value will be ignored even if set.
Address This sets the address targeted for applying "Data mask". (Note 1) -
However, if an illegal address (highest-order bit 0) is input, an error
will occur.
than "3" or "4" (address conditions, true/false), the value
will be ignored even if set. This item can be set with the
same methods as "address 1 to 8".
Data This sets the data for judging the results of applying "Data mask" -
on "Address".
than "3" or "4" (address conditions, true/false), the value
will be ignored even if set.
Data mask This sets the data mask to be applied on "Address". -
(Note) If both " Start condition " and " End condition" are set to
other than "3" or "4" (address conditions, true/false), the
value will be ignored even if set.
(Note1) When "3" or "4" is set in "Start condition", be sure to set the address, the data, and the data mask.
This applies to "End condition" as well. If these are not set, sampling may not start.
When the same values are set in both "Start condition" and "End condition", sampling will not take a
place.
Example of "End condition" by setting address
Setting End condition :3
Address : 12345678
Data : 00000100
Data mask : 0000FFFF
Meaning of setting The trigger for sampling end turns ON when the results obtained by applying data
mask "0000FFFF" on the data of which address is "12345678" matches "00000100".
I - 410
(Note 2) When "1" is set in "Start condition"/"End condition", the common variable uses the floating decimal
point type. Thus, if the calculation results are used, an error will occur, and the value may not be
recognized as "0" because of its calculation error.
When using a multi-part system, the trigger will turn ON when the conditions are satisfied even if
only one part system is used.
(Note 3) The variable data settings are validated immediately only from the program. These will not be
validated immediately with settings from the screen or an external input.
(Note 4) Even if "End condition" is satisfied, the subsequent flow will differ according to the value set in
"Process type". (This also applies when ending manually.)
Sampling completed
Start trigger ON Start trigger ON End trigger ON
(buffer full)
#21 Process type Flow of sampling process
One-shot
Sampling Sampling stopped
Process continued until sampling is completed

Repeat Waiting for trigger
Sampling Sampling Sampling stopped
Ring buffer Sampling stopped

Sampling
5.8.1 Executing NC Data Sampling
Sampling is started when the menu Samp start is pressed.
Operation method (Executing NC data sampling)
(1) Set sampling condition and data.
(2) Press the menu Samp start . The sampling starts and the menu cannot be selected.
When the sampling end condition is satisfied, the state
will be "Sampling stop". The menu Samp start can
be selected.
(Note 1) The sampling will not end even if transferred to another screen in sampling.
(Note 2) The data set in this function will not be output to the parameter.
(Note 3) The contents of "State" is returned to "Sampling stop". (The parameters related to NC data
sampling is maintained.)
(Note 4) The data is displayed in 16 digits. However, the data can be set up to 8 digits.
I - 411
5.8.2 Outputting Sampling Data
Sampling can be output on the data I/O screen under [Mainte] tag.
Operation method (Outputting the sampling data)
(1) Select the data I/O screen under [Mainte]

tag.
(2) Set the following items in the file setting

column A.
A:Dev: Memory
Dir: /LOG
File: NCSAMP.CSV
(3) Set the destination device, directory, file

name in the setting column B.
(4) Press the menu Trnsfr A->B . Sampling file will be output.
(Note 1) The data can not be output when the sampling is not executed.
(Note 2) The data can be output only when the sampling output valid parameter (#1224 aux08/bit0) is
valid.
(Note 3) The output format differs depending on the sampling parameter "Output form".
(Note 4) The header information is not added to output sampling data.
I - 412
Output file format (when output in decimal figure)
Sampling data is output in decimal figure when the sampling parameter "Output form" is set to "0".
(Example) When the number of channel is 3, the address is 1 to 3, and the output unit is E,
it stops when 1ch is 100mm, 2ch is -100mm and 3ch is 50mm.
Output format
1ch 2ch 3ch
1st data 200000000 -200000000 100000000
2nd data 200000000 -200000000 100000000
3rd data 200000000 -200000000 100000000
: : : :
Output file format (when output in hexadecimal figure)
Sampling data is output in hexadecimal figure with 8 digits when the sampling parameter "Output form" is set
to "1".
The output data is the sampling buffer dumped in the length of the long type data (32bits).
(Example) When the number of channel is 3, the address is 1 to 3, and the output unit is C,
it stops when 1ch is 100mm, 2ch is -100mm and 3ch is 50mm.
Channel Output format

1st data 1ch 0001E840
2ch FFE17B80
3ch 000F4240
2nd data 1ch 0001E840
2ch FFE17B80
3ch 000F4240
3rd data 1ch 0001E840
2ch FFE17B80
3ch 000F4240
: :
I - 413
5.9 Anshin-net Screen

5.9.1 Message Display Screen
Anshin-net connection status and message from NC service are displayed on this screen. Operator can make
one-touch calls; validate operator notification; and change the notifying party's telephone No.
(1)
(2)
(3)
(4) (5)
(6)
Display items

(1) Anshin-net Flickers during Anshin-net communications.
connection status No displays during off-line state.
(2) Message Message (Anshin-net connection status, etc.) is displayed.
(3) NC service message Message from NC service is displayed.
Up to 5 lines with 71 characters in each line can be displayed.
(Note 1) If a message does not fit in the display area, the overflowed message is truncated.
(Note 2) The message will be held until the server is connected again; the power is turned
OFF; or operator notification operation is validated.
(Note 3) When a message is received while Anshin-net screen is not displayed, the
message will be displayed as soon as the screen is opened.
(4) Notice tel-num Telephone No. of the notifying party is displayed.
(5) Comment Comment concerning the notifying party is displayed.
(6) Communication Message on communication status is displayed.
status message "Transmission completed" and "Reception completed" displays will go out at screen
transitions.
I - 414
Menus

Anshin Jumps to the Anshin-net parameter1 screen. C "Setting the parameter"
param.1
Jumps to the Anshin-net parameter 2 screen. C "Setting the parameter"
Anshin
param.2 (Note) This menu can be used only when a password has been set
by the machine tool builder.
No.1 This changes the notifying party's telephone No. to the number at B
Notice tel-num1 in the Anshin-net parameter 1 screen.
No. 2 This changes the notifying party's telephone No. to the number at B
No. 3 This changes the notifying party's telephone No. to the number at B
1-shot This changes the notifying party's telephone No. to the number set A "Setting the arbitrary
No. arbitrarily. telephone No."
Notice This validates/invaliates the operator notification. B "Making the operator
Ope. notification valid"
Call This makes a one-touch call. B "Making a one-touch
call"
I - 415
5.9.2 Anshin-net Parameter 1, 2 Screen
The notifying party's telephone No. and comments are set in this screen.
Anshin-net parameter 1
# Item Details Setting range (unit)

10801 Notice tel num 1 Set the call-back telephone No. (1) used for one-touch Within 28 characters
call and operator notification.
Enter from the area code for domestic calls, and from
the communication company No. for international calls.
Hyphens "-" can be used as a delimiting character.
10802 Comment 1 Set a comment, such as the party's name, for the Within 20 alphanumerical
notification party telephone number 1. characters (excluding
spaces)
spaces)
spaces)
10807 Password Set the password for sharing of machining data 4 characters
(one-byte alphanumeric
characters, without space)
10808 Customer number Set the user number for sharing of machining data. Within 8 characters
(one-byte alphanumeric
characters, without space)
10812 Anshin-net valid Set valid/invalid of the Anshin-net function. 0: Invalid
1: Valid
I - 416
Operation method (Executing NC data sampling)
(1) Set sampling condition and data. Notice Ope. menu key is highlighted and the other
menus will be disabled.
"Operator notice effective" is displayed.
When the Notice Ope. menu key is pressed again while operator notification is valid, menu's highlight
and disabled state will be canceled, and the operator notification will be disabled.
If machining ends normally/abnormally while operator notification is valid, system is connected to the NC
service.
("Dialing" → "Waiting for dialing" → "Verifying the user registration" → "Connecting" → "Sending" →
"Connecting" → "Transmission completed")
The message from NC service is displayed.
After data has been sent, menu's highlight and disabled state is canceled, and operator notification will
be disabled.
A call is made to the currently displayed notifying party's telephone No. from the call center.
Making a one-touch call
(1) Press the Call menu key. Call menu is highlighted and the other menus will be
disabled.
"Carry out one-touch call? (Y/N)" is displayed.
(2) Press "Y" or the INPUT key. Connects to NC service. Connection status is displayed
in order.
("Dialing" → "Waiting for dialing" → "Verifying the user
registration" → "Connecting" → "Sending" →
"Connecting" → "Transmission completed")
Diagnosis data is sent to NC service after connection
has been established.
After diagnosis data has been sent, menu's highlight
and disabled state is canceled, and the message from
NC service is displayed.
Setting the arbitrary telephone No.
(1) Press the 1-shot No. menu key. 1-shot No. menu is highlighted and the other menu will
be disabled.
The mode for setting the arbitrary No. is entered.
The cursor is displayed at the notifying party's
telephone No. column.
(2) Enter numerical value. Menu's highlight and disabled state are canceled, and
012-345-6789 INPUT "012-345-6789" is displayed at the cursor position.
The notifying party's telephone No. is changed to the
number entered.
If the 1-shot No. menu key is pressed again after an arbitrary telephone No. has been set, the
notifying party's telephone No. will be the number already selected (No. 1, 2, or 3).
(Note 1) If the No.1, No.2, or No.3 menu key is pressed after an arbitrary telephone No. has been input,
the displayed arbitrary telephone No. will be cleared and the notifying party's telephone No. will
be changed to the number 1, 2, or 3 on the Anshin-net parameter 1 screen.
I - 417
Setting the parameter
(1) Press the Anshin param.1 menu key in Anshin-net parameter 1 screen is displayed.
the message display screen. (Press the Anshin param.2 menu key to set the
parameter for Anshin-net parameter 2 screen.）
(2) Move the cursor to the item to be set with The cursor is moved to the item to be set, and the value
the and keys. currently set in the data setting area is displayed.
(3) Enter a value and press the INPUT The input value is reflected at the cursor position.
key.
Press the cancel key to return to the message display screen.

The transmission and reception of data can be operated on the Edit screen and the Maintenance screen.
Refer to "4.5.14 Sharing Machining Data" and "6.2.13 Sharing Machining Data" for the operation method.
I - 418
5.10 Machine Tool Builder Network System (MTB Net) Screen
5.10 Machine Tool Builder Network System (MTB net) Screen

5.10.1 Message Display Screen
Diagnosis data can be transmitted to the machine tool builder from this screen. The net connection state and
messages from the machine tool builder are also displayed on this screen.
(1)
(2)
(3)
(4)
Display items

(1) Machine tool builder Flickers during machine tool builder network communications.
network connection No displays during off-line state.
status
(2) Message Message (machine tool builder network connection status, etc.) is displayed.
(3) MTB message Message from machine tool builder is displayed.
Up to 5 lines with 71 characters in each line can be displayed.
(Note 1) If a message does not fit in the display area, the overflowed message is truncated.
(Note 2) The message will be held until the power is turned OFF; or next message from
machine tool builder is received.
(Note 3) When a message is received while machine tool builder network screen is not
displayed, the message will be displayed as soon as the screen is opened.
(4) Communication Message on communication status is displayed.
status message "Transmission completed" and "Reception completed" displays will go out at screen
transitions.
I - 419
Menus
MTB Jumps to the MTB net parameter1 screen. B "Setting the parameter"
param.1 (Note 1) This menu cannot be selected while connecting the
machine tool builder network.
Jumps to the MTB net parameter2 screen. B "Setting the parameter"
(Note 1) This menu can be used only when a password has been set
MTB
param.2 by the machine tool builder.
(Note 2) This menu cannot be selected while connecting the
machine tool builder network.
Warning This cancels the warning of network service. C "Canceling a warning of
cancel network service"
This transmits diagnosis information to the machine tool builder. A "Transmitting diagnosis
Send
information to the
machine tool builder"
I - 420
5.10.2 MTB Net Parameter 1, 2 Screen
The valid/invalid of the machine tool builder network (MTB net) function is set in this screen.
Menus

param.1
param.2 (Note 1) This menu can be used only when a password has been set
by the machine tool builder.
Return Jumps to the MTB net screen. C "Canceling a warning of
network service"
MTB net parameter 1
# Item Details Setting range (unit)

10813 MTBnet enable Set valid/invalid for the machine tool builder network 0: Valid
functions. 1: Invalid
Standard setting: 0
(Note) Other than 0/1 is
invalid.
I - 421
Transmitting diagnosis information to the machine tool builder
(1) Press the menu key Send. The Send menu will be highlighted, and the message
"Transmit diagnosis data? (Y/N)" will appear.
(2) Press "Y" or the INPUT key. Connects to the machine tool builder. Connection
status is displayed in order.
Diagnosis data is sent to the machine tool builder after
connection has been established.
After diagnosis data has been sent, menu's highlight is
canceled, and the message from the machine tool
builder is displayed.
Canceling a warning of network service
(Note 1) A warning message will appear if an error occurs when reception of the diagnosis results is
completed or during communication.
Setting the parameter
(1) Press the MTB param.1 menu key in MTB net parameter 1 screen is displayed.
the message display screen. (Press the MTB param.2 menu key to set the
parameter for MTB net parameter 2 screen.）
(2) Move the cursor to the item to be set with The cursor is moved to the item to be set, and the value
the and keys. currently set in the data setting area is displayed.
(3) Enter a value and press the INPUT The input value is reflected at the cursor position.
key.
(Note 1) To return to the message display screen, Return key or CANCEL key is pressed.
(Note 2) When the communication between the call center and the machine tool builder is started while
displaying MTB net parameter screen 1 or 2, the parameters cannot be changed until the
communication is completed. The operation message "Network service is connected" appears.
I - 422
6. Maintenance Screens
The NC memory can be formatted, the absolute position parameters setting, the SRAM backup, etc. are
possible on this screen. Important operations are protected with a password.
(1)
(3)
(2)
Display items

(1) PLC stop state The PLC state (stopped/stop canceled) is displayed.
Stopped : "STOP" is highlighted.
Stop canceled : "STOP" is not highlighted.
(2) Explanation of menu A brief explanation of the menu operations is displayed.
operations
(3) Serial No. Currently set NC information (serial No., model name and unit name) is displayed.
I - 423
Menus

Psswd This changes the screen related to the maintenance by setting the A
input password.
PLC This forcible stops the PLC ladder process. If this menu key is pressed C
stop in the stopped state, the stop is canceled.
All This backs up (saves) or restores (reloads) the file such as SRAM etc. C
backup to designated device.
System This automatically executes necessary parameter setting for driving C

setup servomotor only by setting necessary minimum item.
Adjust This changes the screen to that for adjusting the spindle analog C
S-ana output.
To This sets the absolute position for servo axis (arbitrary NC axis, PLC C
Abs pos axis).
This carries out absolute position setting or test operation by the C
AUX
test auxiliary axis forward run/reverse run.
This executes the followings. C
Setting to collect the diagnosis data
Collect
set Confirming the diagnosis data collection status
Starting/Stopping to collect the diagnosis data
Clearing the diagnosis data
This formats the NC memory. B
Format
T-life This formats the tool life management data. B

format
Serial This changes the NC serial No. A
No.Set
Console The console is executed. The MS-DOS window will appear. C
exec
To This changes the screen to the Data Input/Output screen. C
In/out
To This changes the screen to the Parameter screen. C
param
<700 series> B
SRAM This backs up the NC SRAM information on the HD.
backup <70 series>
This backs up the NC SRAM information on the memory card.
HMI This quits the screen operation. B
Quit
Backing up the NC SRAM information
(1) Press the menu SRAM backup . A message appears to confirm the backup execution.
(2) Press Y or INPUT . The backup is executed.

<700 series>
Press a key other than Y or The data is backed up into "D:\ NCFILE \ SRAM.BIN"
INPUT to cancel the backup. on the HD.
(If SRAM.BIN already exists, the original file will be
saved as SRAM.BAK.)
<70 series>
The data is backed up into the memory card.
I - 424
6.1 Parameter Screens

The various parameters can be displayed and set on this screen.
The configuration of the all parameter screens is applied to one of the following five patterns.
<Pattern 1> This is the screen for setting the common parameters for the axis, device, etc.
(Process param, etc.)
<Pattern 2> This is the screen for setting the parameters having an array structure for each axis
(Axis param, etc.)
I - 425
<Pattern 3> This is the screen for setting parameters common for the axis and device, etc.
The parameter names are not displayed
(Machine error data, PLC constant, etc.)
<Pattern 4> This is the screen for setting parameters having an array structure for each part system
(Base system parameters, etc.)
I - 426
<Pattern 5> This is the screen for setting the subprogram storage destination parameters
I - 427
Menus

A arbitrary parameter No. can be selected. A 6.1.2 Selecting the
Param When the parameter No. is set and the INPUT key is pressed, the Parameter No.
No. parameters will appear with that No. at the head. The cursor will also
move to that No.
Area This copies the parameter setting values in the designated range. A 6.1.4 Copying/Pasting
copy The range is designated with numbers. Parameters
This pastes the range of parameters designated in area copy. They B
are pasted in a parameter corresponding to the axis or part system
Area where the cursor is.
paste
Once copied, a parameter can be pasted any number of times until a
new parameter is copied.
This can be selected when there are five or more display axes in the C -
Next selected part system.
axis This is used in the screen for the parameters having an array structure
for each axis.
This can be selected when there are two or more screen display part C -
Next
system systems.
Use this with the parameter screen for each parameter.
This can always be selected when the base part system parameter -
screen is open.
The display changes to the PLC axis display when this menu is
pressed.
Process This changes the screen to the user parameter screen. C 6.1.5 User Parameters
param (Note) The barrier data is displayed only for the L specifications.
Control
param
Axis
param
Operate
param
Barrier
data
I/O
param
Ethernet
param
Link
param
Subpro
stor
I - 428

BaseSys This changes the screen to the Machine parameter screen. C -
param (Note 1) Normally, the machine parameters can be referred to, but
cannot be set.
BaseAx (Note 2) The "RotAxis param", "AUX param", "Open param 1" and
spec "Open param 2" menus are displayed only when these
BaseCom options are valid.
param (Note 3) The "AUX param" is displayed for 700 series only.
Axis
spec
Zp-rtn
param
Abs pos
param
Servo
param
Spindle
spec
Spindle
param
RotAxis
param
PLC
timer
PLC inc
timer
PLC
counter
PLC
constnt
Bit
select
Er Comp
param
Er Comp
data
Macro
list
Posn
switch
AUX
param
Open
param1
Open
param2
CC-Link
param1
CC-Link
param2
I - 429
6.1.1 Changing the Parameter Display
Changing to the computer link parameters
(1) Press the menu change key until the menu The menu Link param appears.
Link param appears.
(2) Press the menu Link param . The computer link parameters appears.
The menu Link param is highlighted.
I - 430
6.1.2 Setting the Parameters

The method of setting the parameters is explained in this section. For the setting range of each parameter,
refer to "3.8.8 Parameter list".
Press the menu key to select the parameter screen, and select the data to be set with the cursor key.
"8201 Axis removal" Setting Y1 axis to "1"
(1) Press the menu Axis param .
(2) Use the , , and keys to The cursor moves to the position of the setting target
data.
move the cursor to the position to be set.
The cursor can also be moved with the
menu Param No. .
Refer to "6.2.2 Selecting the parameter
No.".
The current setting value is displayed in the input area.
(3) Input the value. The setting value appears, and the cursor moves.
1 INPUT
I - 431
"8205 OT+" Setting X1 axis to "100.0" and Z1 axis to "200.0"
(1) Press the menu Axis param .
(2) Use the and keys to move the The cursor moves to the position of the setting target
data.
cursor to the position to be set.
(The row does not need to be designated
with the and keys.)
The current setting value is displayed in the input area.
(3) Input the value. The setting value appears, and the cursor moves.
(Format: 1st row/2nd row/3rd row/4th row)
100//200 INPUT
(Note 1) If PR appears at the lower right of the screen when the parameter value is changed, the
parameter value will be validated when the power is turned ON again.
(Note 2) If the INPUT key is pressed without inputting a value, the cursor will move without changing the
parameter setting value.
(Note 3) If a character string, such as an axis name or input/output device name, is set in the parameter, the
setting will be cleared when 0 is input and the INPUT key is pressed.
(Note 4) Parameters for up to four rows, which are as currently displayed, can be set at once.
(Note 5) If the parameter value for several rows is input simultaneously, the values will be set from the
currently displayed left end no matter which row the cursor is currently at.
I - 432
6.1.3 Copying/Pasting Parameters
Designating the cursor position and copying
(1) Move the cursor to the parameter to be

copied.
(2) Press the menu Area copy and The menu is highlighted.
INPUT . The setting value of the parameter at the cursor
position highlighted.
(Note) When the screen has an array structure for each axis or each part system, an error will occur if
different rows (axis or part system) are designated for the copy start position and end position.
I - 433
Copying by designating the parameter No. with key inputs

axes or part system to be copied.
(2) Press the menu Area copy . The menu is highlighted.
(3) Designate the copy range. The copy target range is highlighted.
Format: First No./Last No. The menu highlight returns to normal.
8203/8205 INPUT
If the last No. to be copied is the last No. of

the currently displayed parameter type, "E"
can be designated. (Example) 8201/E
If only one parameter is being copied,
input only the No. of the parameter to
copy, and then press the INPUT key.
(Note 1) The copy target range highlight returns to the normal display by pasting. The copy target range is
valid until the parameter type display is changed.
(Note 2) Only the currently displayed parameter types can be copied.
(Example) If the parameter numbers #1001 to #1028 of the base system parameter are designated
as the copy target range, the base axis specification parameters #1013 to #1024 cannot
be copied.
Pasting the copied data

axes or part system where the data will be
pasted.
(2) Press the menu key Area paste . The menu is highlighted, and a message confirming
the operation appears.
(3) Press Y or INPUT . The copied data is written to the parameter with the
same number as when copied, in the area where the
The copied data will not be written in when cursor is.
the N key is pressed. The menu highlight returns to normal.
(Note) If the corresponding parameter is changed after the copy target range is designated, the changed
value will be pasted.
I - 434
6.1.4 User Parameters

The user parameter configuration is as shown below.
Area copy
Next axis Next system
Parameter type Parameter No. Area paste
menu menu
menu
8001 to 8094
8621 to 8627
Process Parameter - Δ (Note 3) Δ (Note 3)
8701 to 8712
19425 to 19428
Control Parameter 8101 to 8124 - - -
(Note 1) (Note 2)
Axis Parameter 8201 to 8215 Δ - Δ
Operation Parameter 8901 to 8921 - - -
(Note 5) (Note 3)
Barrier data 8300 to 8319 - Δ {
Input/Output Parameter 9001 to 9530 - - -
Ethernet Parameter 9701 to 9781 - - -
Computer Link Parameter 9601 to 9630 - - -
Sub-program storage 8880 to 8889
- Δ (Note 3) Δ (Note 3)
destination parameter
(Note 1) This is valid only when the total number of valid NC axes and PLC axes in the entire part system is
five or more.
(Note 2) This is valid only when the total number of valid NC axes and PLC axes in the entire part system is
two or more.
(Note 3) This is valid only when the number of valid part systems is two or more.
(Note 4) The barrier data appears only for the L specifications.
Operation methods (Subprogram storage destination parameters) Example 1
Setting the device (Example: Assign FD to D1)

(1) Set the cursor to the "#8882 Subpro stor
DI: dev" (D1 device).
(2) Input F , and press the INPUT key. "FD" appears at "#8882 D1: dev".
The cursor moves down one line.
(Note) Input the following values for the device name.

M: Memory, G: HD, R: Memory card, D: DS (Data server), T: Ethernet, F: FD
(In 70 series, only "Memory", "Memory card" and "Ethernet" can be used.)
Operation methods (Sub program storage destination parameter) Example 2
Setting the directory (Example: Setting "/TEMP1/TEMP12/TEMP123" to D1)

(1) Set the cursor to "#8883 dir" (D1 directory) The current "#8883 D1: dir" contents are echoed back
to the input area.
(2) Set "/TEMP1/TEMP12/TEMP123", and The value is set, and the cursor moves down one line.
press the INPUT key.
I - 435
6.1.5 Echo Back

If more than 14 characters can be set for the parameter, or for bit-related parameters, the parameter setting
value at the cursor position appears at the input area. If more than 14 characters are set in the parameter, "..."
will appear in the data field.
< Target parameters>

Parameter screen name Parameter No., parameter name
Base Common Param #1217 aux01 to #1228 aux12
#1229 set01 to #1240 set12
#1265 ext01 to #1300 ext36
#1926 IP address
#1927 Sub-net mask
#1928 Gateway
#1930 Host Address
#1934 Local IP address
#1935 Local Subnet mask
#11005 PC IP address
Base System Param #1204 TmirS2
#1210 RstGmd
#1573 Ret1
#1574 Ret2
Bit Selection Param #6401 to #6596
Ethernet Param #9702 IP address
#9703 Sub-net mask
#9704 Gateway
#9711 Host 1 host name
#9712 Host 1 user name
#9714 Host 1 directory
* These also apply for hosts 2 to 4.
Sub-pro Storage Destination Param #8881 Subpro stor D0:dir
* This also applies for devices 1 to 4.
Parameters for which 14 or more characters can be set Bit-related parameters
I - 436
6.2 Input/Output Screen

The Input/Output screen is used to carry out NC data input/output between the NC internal memory and the
external input/output devices.
Here, the hard disk built into the NC device is also treated as external devices.
In 70 series, only "Memory", "Memory card", "Serial", "Ethernet" and "Anshin-net server" can be used.
(1)
(2)
(4)
(3) (5)
(6)
(7)
Display items

(1) Number of programs This displays the registration information of machining program of the selected
registered and remainder device.
(Note 1) Number of programs registered :
This displays the number of programs previously registered as user machining
programs.
Remainder :
This displays the remaining number of programs that can be registered.
When "Memory" is selected as the device, the total of the number of programs
registered and the remainder is the maximum number of registrations set in the
specifications.
(2) Number of memory This displays the number of characters of the machining program of the selected
characters and remainder device.
(Note 1) Number of memory characters :
This displays the number of characters previously registered as user machining
programs.
Remainder :
This displays the remaining number of characters that can be registered. The total
of the number of memory characters and the remainder is the maximum number of
memory characters set in the specifications.
I - 437

(3) List (Note 2) This displays a contents list (directory and file name) of the directory in the setting
column (file setting column A or B) where the cursor is currently located.
Program :
When "Memory" is selected for the device, this displays the file name (program No.)
of the machining programs already registered. The file names are displayed in
order from the smallest number, from 1 to 99999999. When a device other than
memory is selected, this displays the file name and directory to be included in the
directory that is set in the current setting column.
When the number of characters exceeds 12, the excess is indicated as "*".
Character :
The size of each file (when memory is selected for the device, the number of
characters in the machining program). When directory is selected, this displays
"DIR".
Comment :
This displays the comment (up to 17 alphanumeric characters and symbols) of
each file.
The date which the file is updated is displayed for the HD, FD, memory card, DS or
Ethernet.
When the number of characters exceeds 17, the excess is not displayed.
(4) File setting column A This sets the device, directory, and file name of the target file for transfer, compare,
erasing, etc., operations.
(5) File setting column B When transferring, the file name of the transfer origin file is set. When renaming, the
file name before renaming is set. When erasing, the erasing range is set. When the
number of characters exceeds 28, the excess is not displayed.
(6) Input data This displays the data being transferred.
(7) Comparison data This displays the data being compared. If an error occurs during comparison, the
block with the error is displayed.
(Note 1) Depending on the device, some items are not displayed.

Device Memory Anshin-net
Memory HD Serial DS Ethernet FD
Display item card server
Number of programs
{ { × { { { { ×
registered
Remainder { × × × × × × ×
Number of memory
{ { × { { {* { ×
characters
Remainder { { × { { × { ×
List { { × { { { { ×
{ : Displayed × : Not displayed
* : When the Ethernet parameter "#97*1 Host n no total siz" is set to 1, the number of host memory
characters will not appear.
(Note 2) The list does not appear when using serial.
I - 438
Menus

This changes the setting area to file setting column A (transfer origin) C 6.2.1 Changing the Valid
Area
change or file setting column B (transfer destination). The display of the valid Area
area (A or B) is highlighted.
This displays the submenu of the machining program storage area. A 6.2.2 Selecting a
Device When the submenu is selected, the device is confirmed, and if a Device, Directory, and
select directory exists it is set in the root. File
The memory is selected as the default.
This menu sets the directory that carries out input/ output operations, A
Dir and is on standby for input. Note that when memory is selected for the
device, the directory can be selected from the submenu.
This menu sets the file name that carries out input/ output operations, A
File and is on standby for input. When memory is selected for the device,
name
setting is not necessary if the directory is not the program.
List This updates the list. The list of the directly selected in the currently C -
update valid file setting column (A/B) is updated.
This copies the file in file setting column A (transfer origin) to the file B 6.2.3 Transferring a File
Transfr setting column B (transfer destination). (The transfer origin file is not
A→B changed.) A message appears during transfer and when the transfer
is completed.
Compare This compares the files in file setting column A (transfer origin) and file C 6.2.4 Comparing Files
A:B setting column B (transfer destination). (Compare)
This erases the file in file setting column A. B 6.2.5 Erasing a File
Erase A (Note) The NC memory (excluding programs), serial and Ethernet
(host file) cannot be erased.
This erases the file in file setting column B. B
Erase B (Note) The NC memory (excluding programs), serial and Ethernet
(host file) cannot be erased.
This changes the name of the file in file setting column A (transfer B 6.2.6 Changing a File
origin) to the name of the file in file setting column B (transfer Name
Rename destination).
A→B
(Note) The same device must be selected for A and B.
The NC memory (excluding programs) and serial cannot be renamed.
Comment This changes whether to show or hide the comment field. B
nondisp
This creates a new directory in the directory of the currently valid file A 6.2.7 Creating a
Dir setting column (A/B). Directory
create The directory can be created when HD, FD, memory card or DS is
selected for the device.
The file contents in the file setting column B are added to the file in the B 6.2.8 Merging a File
file setting column A. (The file in the file setting column B is not
Merge changed.)
B→A
(Note) The NC memory (excluding programs), serial and Ethernet
(host file) cannot be merged.
FD This formats the FD. A 6.2.9 Formatting an
format This menu is only for 700 series. External Device
MemCrd The formats the front IC card. A

format
DS This formats the NC compact flash memory. A
This cancels a warning from network service. C 6.2.13 Sharing
Warning Machining Data
cancel "Canceling a warning
from network service"
This interrupts the process (transfer, compare, etc.) during execution. C -
Stop
I - 439
6.2.1 Changing the Valid Area

When setting the file setting field A or B device, directory and file name on this screen, the area containing
these must be valid.
The display area can be changed by pressing the menu key ( Area change ) or the cursor key and .
After changing, the data setting operation is valid in that area.
File setting field A is valid. File setting field B is valid.
Changing the valid file setting field
When file setting field A (top) is valid

(1) Press the menu Area change . The file setting field B (bottom) is validated.
This can also be changed with the cursor

key .
I - 440
6.2.2 Selecting a Device, Directory and File
File selection sequence
Designate the device where the target file is located. → Select from the sub menu.
↓
Designate the directory with a full path. → Input the full path or select from the list.
↓
Designate the file name. → Input the file name or select from the list.
Menu used
Device select menu's submenus

This selects the NC memory (program, parameter, user PLC, NC C -
Memory
data).
This selects the hard disk. C -
HD
This selects the RS-232C device (PC, tape, etc.). C -
Serial
Memory This selects the front IC card. C -

card
This selects the NC compact flash memory. C -
DS This menu is only for 700 series.
This selects the Ethernet-connected host computer. C -
Ethernet
This selects the floppy disk. C -

FD
Anet This selects the Anshin-net server. C 6.2.13 Sharing

server Machining Data
Dir (other than memory) and File name menu submenus

The cursor appears in the list display. The list contents can be A -
selected with the INPUT key.
From When a directory is selected, the contents of the selected directory
list are displayed in the list. Continued selection is possible.
When a file name is selected, the file name is temporarily displayed in
the input area. When the INPUT key is pressed again, it is fixed.
I - 441
Selecting methods for device, directory, and file name
Designation method
Device Designation target file
Device Directory File name
NC memory • Machining program Select from the - Key input in the input
• User macro submenu (Default) area, and press INPUT
• Fixed cycle
Select from the list
Other than the Select from the Key input in the input area, -
machining program submenu and press INPUT (Fixed)
Select from the submenu
Other than the All Select from the Key input in the input area, Key input in the input
NC memory submenu and press INPUT area, and press INPUT
Select from the list Select from the list
The device can be selected from the submenu. (The devices that can be used will differ depending on the
specifications.)
One of the following methods can be used to designate the directory (for devices other than the NC memory)
and file name.
• Set the directory path (full path) or file name in the input area, and press the INPUT key.
• Press submenu From list of the menu Dir or File name . Move the cursor to the target directory or
file name, and press the INPUT key.
A wild card (*) can be used when selecting a file name.
Notes when selecting a file
(1) During directory and file name setting, the designated directory, path or file name will be set, even if it
does not actually exist. This will not cause an error. Note that the previously set directory is overwritten.
(2) When a file in the NC memory other than a machining program is designated, it is not necessary to set
the file name. (The file name is fixed.)
(3) When a file name is selected from the menu, it first is displayed in the input area. However, at this time
the file name has not yet been fixed. Press the INPUT key again to fix the file name.
(4) When the key is pressed when setting a file name, the file name in the input area is erased.
(5) When a fixed cycle program is designated, the basic common parameters "#1166 fixpro" must be set.
Select "Memory" for the device, and "Program" for the directory.
I - 442
Selecting an NC memory program
(1) Press the menu Device select . The following menu appears.
(2) Press the menu Memory . "Memory" appears in the device name, and the default
"Program" appears in the directory.
(3) Press the menu File name . The following menu appears.
<When inputting the file name from the input area>

(4) Input the file name
10013 INPUT
<When selecting the file name from the list>

(4)-1 Press the menu From list . The cursor appears in the list.
(4)-2 Move the cursor to file name to be The selected file name appears in the input area.
selected, and fix.
, , INPUT
(4)-3 Press the INPUT key. The selected file name appears.
I - 443
Designating multiple files
(1) Designating multiple serial files

Multiple serial files can be transferred, compared and erased in the file setting column A. Set as follows
in this case.
File : First file name

- : Last file name
(2) Using a wild card

A wild card (*) can be used in the file name.
(Note) When serial or Anshin-net server is used, multiple files cannot be compared.
File : * All files will be selected.

-
Selecting an NC memory file other than a program
(2) Press the menu Memory . "Memory" appears in the device name, and "Program"
appears as the default in the directory.
(3) Select the menu Dir . The following menu appears.
(4) Press the menu Tool offset . The directory and file name appear.
(Note) The file name for each directory is fixed. Refer to "6.2.10 List of file names" for the file names.
I - 444
Selecting a device file other than the NC memory
(2) Select a device. The device name appears. The root directory is
selected as the default.
(3) Designate the directory. The mode changes to the mode for inputting the
Select the menu Dir directory name.
The following menu appears.
<When inputting the directory from the input area>

(4) Input the directory path as a full path.
/PRG/PRECUT INPUT
<When selecting the directory from the list >

(4)-1 Press the menu From list The cursor appears in the list.
(4)-2 Move the cursor to directory to be The selected directory appears in the data setting
selected, and fix. column.
The contents of the selected directory appear in the
, , INPUT list.
Repeat this operation until the target

directory is reached.
When the target directory is reached,
press the key and quit the mode for
inputting the directory.
I - 445
(5) Designate the file name. The mode changes to the mode for inputting the file
Press the menu File name name.
The following menu appears.
<When inputting the file name from the input area>

(6) Input the file name
10013.PRG INPUT
<When selecting the file name from the list>

(6)-1 Press the menu From list . The cursor appears in the list.
(6)-2 Move the cursor to file name to be The selected file name appears in the input area.
selected, and fix.
, , INPUT
(6)-3 Press the INPUT key. The selected file name appears.
I - 446
Canceling the input mode
(1) Press the Device Select , Dir or The submenu appears.

File name .
To cancel the data input at this time, press
the key.
(2) Press the key. The details in the input area are erased, and the main
menu appears.
Main menu
The details in the data input area are erased.
Submenu
I - 447
6.2.3 Transferring a File
Operating method
(1) Press the menu Area change , and

select file setting column A.
(2) Designate the transfer origin device, The designated file appears.
directory and file name. Multiple files can be designated in the file setting
column A. Designate the first and last file name of the
target range. A wildcard "*" can be designated for the
file name.

select file setting column B.
(5) Press the menu Trnsfr A ->B . A message appears to confirm the transfer.
(6) Press Y or INPUT . The file transfer starts. The data being transferred
appears in the input data display column.
A message appears when the transfer is completed.
INP data : G91 G28 XYZ;

F1000;
CMP data :
! Caution
! " ; ", "EOB", "%", and “EOR” are symbols used for explanation. The actual codes for ISO are "CR,
LF" ("LF") and "%".
The programs created on the Edit screen are stored in the NC memory in a "CR, LF" format,
however, the programs created with external devices such as the FD or RS-232C may be stored in
an "LF" format.
! To prevent the influence of data loss and data transformation over the line, always carry out data
comparison after transferring a machining program.
I - 448
Notes
(1) Notes related to transferring in general

(a) Depending on the type of file, some data cannot be transferred during automatic operation. Do not
transfer during automatic operation.
(b) When the capacity of the transfer destination is reached during file transfer, only the data transferred
up to that point is registered as a file, and an error will result.
(c) During input to the NC memory or comparison, if the file format size on the NC memory side differs
from the other side file format size (when the maximum number of registrations differs between the
NC memory and the other side), processing is carried out matched to the smaller size.
(Ex. 1) If a format size of 200 files is input for a format size of 1000 NC files, 200 files are registered.
(Ex. 2) If a format size of1000 files is input for a format size of 200 NC files, the files up to the 200th
file are registered and an error message appears. (The remaining files are not registered.)
(d) Up to 223 files, including the directory, can be registered in the FD's root directory.
(2) Notes when transferring machining program files

(a) For the serial, always set feed (Null) at both ends of the "EOR" code at the head and end. If "EOB"
etc., is directly after "EOR", the operation may not execute normally due to the input buffer influence
during the next input operation.
(b) The transfer speed is slower if there are many registrations.
(c) The size of one block of the machining program should be 250 characters or less.
(d) When using tape, carry out parity V adjustment to improve the reliability of the tape format. Then use
with the input/output parameter "Parity V" validated.
(e) When the machine tool builder macro and fixed cycle program are input to NC memory, change the
program type with the parameter "#1166 fixpro". Also, set in the Input/Output screen as follows.
Device: Memory, Directory: Program
(f) Transferring or verifying the multiple files between the external device connected serially and that
other than the serial connection.
(g) With machining program created before the MELDAS500 Series, "EOB" is registered as "LF".
However, when these programs are stored in the 700/70 Series NC memory, "EOB" will be converted
to "CR LF", and the number of characters will increase. Thus, when all of the machining programs
output from an MELDAS500 Series or earlier NC, having the same specifications as the maximum
memory capacity, are stored in the 700/70 Series NC memory, the memory capacity may be
exceeded.
(h) When the file to be transferred (input) is running or in "program restarting" mode, the operation
message "Executing automatic operation" or "Program restarting" is displayed and file will not be
transferred (input).
(3) Notes when transferring tool offset data files

(a) If an error occurs during offset data transfer, an error message appears on the screen, and the
transfer operation is interrupted.
(4) Notes when transferring parameter files

(a) In the same manner as when setting in the Parameter screen, there are parameters validated
immediately after input, and parameters validated after a restart. Restart when a parameter file has
been transferred to the NC memory.
(b) When a parameter file is transferred to the NC memory, the setting value of the input/output
parameters is also changed. Before transferring next time, set the input/output parameters again.
(c) System parameters can be transferred from the NC memory to an external device, but cannot be
transferred from an external device to the NC memory.
I - 449
(5) Notes when transferring common variable data files

(a) If the variable value is 100000 or more or less than 0.0001 when transferring common variable data,
it is expressed with an exponential expression.
(6) Notes when transferring tool life data files

(a) When tool life data is output from the NC memory, the file information is inserted at the first and last
of the file.
First file information : Number of registered tools (P No.) and the maximum number of possible
registrations (T No.)
Last file information : Finish code
(7) Notes when transferring auxiliary axis parameter files (700 series only)
(a) When the auxiliary axis parameters are input to the NC memory, the same parameter data is
simultaneously transferred to the drive unit. If transferred errors by some causes occur, the
parameter data may be not matched between NC memory data and drive unit.
(8) Notes when transferring sampling data file

(a) When the output form is set as 8-digit hexadecimal number and the parameter
"#1004 ctrlunit" is set to "E (1nm)", accurate data can be output just within 1m.
When the output data length exceeds 1m, lower 32 bits of the sampling data will be output.
6.2.4 Comparing Files (Compare)
Operation method

(2) Designate the device, directory and file The designated file name appears.
name to be compared.

(4) Designate the other side device, directory The designated file name appears.
and file name to be compared.
(5) Press the menu Compare A:B . The file comparison starts. The data being compared
appears in the comparison data display column.
A message appears when the comparison is
completed.
If a comparison error occurs, the block with the error is
displayed in the comparison data display column on
the screen.
(Note) Files that can be compared are text files only.

Correct outcome will not be obtained through binary file comparison.
I - 450
6.2.5 Erasing a File
Erasing a file Erase A

(2) Designate the device, directory and file The designated file appears.
name to be erased.
(3) Press the menu Erase A . A message to confirm the erasing appears.
(4) Press Y or INPUT . The file is erased.

A message appears when the erasing is completed.
The number of programs registered, number of
memory characters and remainder reappear. Press
the List update menu to update the list.
(Note) If the file to be erased is running or in "program restarting" mode, the operation message "Executing
automatic operation" or "Program restarting" is displayed, and the file will not be erased.
Erasing a file Erase B
The operations are the same as method "Erasing a file Erase A " above. Designate the target device,
directory and file name in the file setting column B, and press the menu Erase B .
6.2.6 Changing a File Name (Rename)
Operation method

(2) Designate the original device, directory The designated file name appears.
and file name.

(4) Designate the new device, directory and The designated new file name appears.
file name.
(5) Press the menu Rename A -> B .
(6) Press Y or INPUT. Renaming of the file starts.

A message appears when the renaming is completed.
(Note 1) Select the same device for original and new devices.
(Note 2) If the file to be renamed is running or in "program restarting" mode, the operation message
"Executing automatic operation" or "Program restarting" is displayed, and the name will not be
changed.
(Note 3) If a file that does not exist is designated for the original file, or if an existing file name is designated
for the new file selection, an error occurs, and the name is not changed.
I - 451
6.2.7 Creating a Directory
Operation method

(2) Designate the device. The designated details appear.

The devices that can create a directory are HD, FD,
Memory card and DS.
(3) Designate the directory where the new The designated details appear.
directory is to be created.
(4) Set the new directory in file setting column The designated details appear.
A.
(5) Press the menu Dir create . The designated directory is created.
The directory can also be created in file setting area B.

(Note 1) Up to 223 files, including the directory, can be registered in the FD's root directory.
I - 452
6.2.8 Merging a File
Operation method

select the file setting column A.
(2) Designate the merge destination device, The designated file name appears.

select the file setting column B.
(4) Designate the merge origin device, The designated file name appears.
(5) Press the menu Merge B ->A . A message confirming the merge appears.
(6) Press Y or INPUT . The file merge starts. The data being merged will appear in
the Input Data display column.
A message appears when the merge is completed.
INP data : G91 G28 XYZ;

F1000;
CMP data :
The details of the file in file setting column A will be as follows

when the merge is completed.
(FILE A)
G28 XYZ;
G90 F800; Details of file in file setting
G00 X100. Y100.; column A before merge.
(FILE B)
G91 G28 XYZ;
F1000; Details of file in file setting
G01 X200. Y200.;
M02; column B before merge.
%
The details of the file in file setting column B do not change.
(Note 1) If the merge destination file (file in file setting column A) is running or in "program restarting" mode,
the operation message "Executing automatic operation" or "Program restarting" is displayed, and
the files will not be merged.
(Note 2) The devices that can be merged are the memory, HD, FD, memory card and DS.
I - 453
6.2.9 Formatting an External Device
Operation method (Formatting an FD) [700 series only]
(1) Insert a floppy disk in the FD drive, and A message confirming the formatting appears.
press FD format .
(2) Press Y or INPUT . The FD is formatted.

(Note 1) The FD is formatted with FAT (1.44MB).

(Note 2) The volume label is set when formatting the FD.
Operation method (Formatting a memory card)
(1) Press the menu MemCrd format . A message confirming the formatting appears.
(2) Press Y or INPUT . The memory card is formatted.

(Note 1) The memory card is formatted with FAT16.

(Note 2) The volume label is set when the memory card is formatted.
Operation method (Formatting a DS) [700 series only]
First, press the menu DS format . Refer to "Formatting a memory card" for following operations.
(Note 1) The DS is formatted with FAT16.
(Note 2) Only the DS formatted with FAT16 can be used. The DS with NTFS cannot be used.
(Note 3) As for the DS formatted with NTFS, reformat it with FAT formatted by Windows to use.
(NC cannot convert NTFS partition to FAT formatted.)
(Note 4) The volume label is not set even when the DS is formatted.
6.2.10 List of File Names

There is a directory for each type of data in the NC memory.
Each directory and file name (fixed) in the NC memory is shown below.
Do not change the extensions (.XXX) when storing in a device other than the NC memory.
Data type NC memory directory path Fixed file name
Machining program /PRG/USER (Program No.)
Fixed cycle program /PRG/FIX (Program No.)
Parameters /PRM
Parameters [User, machine] (Text format) ALL.PRM
Auxiliary axis parameter (700 series only) AUXAXIS.PRM
User PLC /LAD USERPLC.LAD
NC data /DAT
Tool compensation amount data TOOL.OFS
Tool life management data TLIFE.TLF
Common variable data COMMON.VAR
SRAM data SRAM.BIN
System configuration data /DGN ASSEMBLY.INF
Decryption code /RLS PASSCODE.DAT
Sampling data /LOG NCSAMP.CSV
Machine data /DGN COMPO.STA
I - 454
Data format (Parameter)
Parameter data format is as follows.

Address Definition Details
N Parameter No. The parameter No. is shown with the value following N.
A Axis No. For axis data, the axis No. is shown with the value following A.
The first axis will be AI.
T Part system No. For data per part system, the part system No. is shown with
the value following T.
($1: T1, $2: T2, PLC axis: T3)
C Spindle No. For spindle data, spindle No. is displayed with a numerical
value following C. Thus, 1st spindle is displayed as C1.
K Split data No. For the parameter with which data is split and set, each split
data is displayed. (Ex. IP address)
P Parameter data The parameter data is shown with the value following P.
The following types of data format are used according to parameter type and display method.
(The address order in one block must use the following format.)
(1) Common parameter (One data item per one # No.)
N1084P0.001
Parameter setting value

Parameter # No.
(a) The output parameter setting value is the same format as the screen display.
(2) Axis parameter
N2001A1P10000
Axis No. 1 to 4
Parameter # No.
(a) When multiple axes are displayed on one screen

The parameter data for the screen in which multiple axes are displayed on one screen is output per
axis.
[Output example]
:
N2001A1P120000
N2002A1P4000 1st axis data
N2003A1P21
:
N2001A2P12000
N2002A2P4000
N2003A2P21 2nd axis data
:
I - 455
(3) Part system parameter
N1001T1P1
Part system No. (1: $1, 2: $2, 3: PLC axis)
Parameter # No.
(a) The parameter data for the screen in which parameters per part system are displayed on one screen
is out put as follows.
[Output example]
:
N1001T1P1
N1001T2P1
N1001T3P0
N1002T1P2
N1002T2P1
N1002T3P0
：
(b) If parameters are displayed per part system upon switch of the part system (when $ key is
pressed), the parameter data is output per part system.
[Output example]
:
N8001T1P99
N8002T1P0
N8003T1P10000
:
N8001T2P30
N8002T2P1
N8003T2P20000
:
I - 456
(4) Spindle parameter
N13001C1P100
Spindle No. 1 to 4
Parameter # No.
(a) When multiple spindles are displayed in one screen

The parameter setting value for the screen in which multiple spindles parameters are displayed in
one screen is output per spindle.
[Output example]
:
N13001C1P100
N13002C1P100 1st spindle data
N13003C1P15
:
N13001C2P100
N13002C2P100 2nd spindle data
N13003C2P15
:
(5) IP address
N1926K1P192
Setting value for parameter data 1

Split data No.
Parameter # No.
[Output example]
(Example) When "#1926 Global IP address" setting value is "192.168.200.1"
:
N1926K1P192
N1926K2P168
N1926K3P200
N1926K4P1
:
I - 457
Data format (Tool compensation amount data)
(1) M type
Tool compensation amount data format is as follows.
G - Fixed to G10.
L Type L10 for tool compensation memory I.
See below for tool compensation memory II.
L10：Tool length shape compensation
L11：Toll length wear compensation
L12：Tool radius shape compensation
L13：Tool radius wear compensation
P Compensation No. The compensation No. is shown with the value following P.
R Compensation amount The compensation No. is shown with the value following R.
[Output example]
%
$1
G10L10P1R0.000
G10L10P2R0.000
：
$2
G10L10P1R0.000
G10L10P2R0.000
：
%
(2) L type
Tool compensation amount data format is as follows.
G - Fixed to G10.
L Type L10 for tool length compensation input.
L11 for tool nose wear compensation input.
P Compensation No. The compensation No. is shown with the value following P.
X X axis compensation The X axis compensation amount data is shown with the value
amount (Absolute) following X. (Absolute)
U X axis compensation The X axis compensation amount data is shown with the value
amount (Incremental) following U. (Incremental)
Z Y axis compensation The Y axis compensation amount data is shown with the value
amount (Absolute) following Z. (Absolute)
W Y axis compensation The Y axis compensation amount data is shown with the value
amount (Incremental) following W. (Incremental)
R Nose R compensation The nose R compensation amount data is shown with the
amount (Absolute) value following R. (Absolute)
C Nose R compensation The nose R compensation amount data is shown with the
amount (Incremental) value following C. (Incremental)
Q Hypothetical tool nose The hypothetical tool nose point is shown with the value
point following Q.
[Output example]
%
G10L10P1X0.000Z0.000R1.000Q3
G10L11P1X0.000Z0.000R0.000Q3
G10L10P2X0.000Z0.000R1.000Q2
：
G10L11P80X0.000Z0.000R0.000Q0
%
I - 458
Data format (Tool life management data)
(1) M type
Tool life management data format is as follows.
G Group No. The group No. for tool life management is shown with the
value following G.
D Tool no. The tool No. is shown with the value following D.
S Status The tool status is shown with the value following S.
M Method The tool life management method is shown with the value
following M.
L Length compensation The length compensation data is shown with the value
following L.
R Radius compensation The radius compensation data is shown with the value
following R.
B AUX. The auxiliary data is shown with the value following B.
E Service lifetime The service lifetime is shown with the value following E.
P Used time The used time is shown with the value following P.
[Output example]
%
LIFEDM()
$1
G100 D1000 S1 M101010 L100 R100 B11 E0 P0
G200 D2000 S2 M000000 L200 R200 B22 E0 P0
G300 D3000 S3 M201020 L300 R300 B33 E0 P0
：
G999999 D9999 S1 M202020 L999 R999 B99 E0 P0
%
(2) L type
(a) Tool life management I
Tool life management I format is as follows.
N Tool No. The tool No. is shown with the value following N.
P Time-used The time-used is shown with the value following P.
E Time-max The time-max is shown with the value following E.
Q Count-used The count-used is shown with the value following Q.
F Count-max The count-max is shown with the value following F.
S Status The status of tool life management is shown with the value
following S.
B AUX. The auxiliary data is shown with the value following B.
[Output example]
%
LIFEL1( TOOL LIFE DATA)
$1
N1 P12.34.56 E45.56 Q6 F7 S1 B0
N2 P2.3.4 E5.6 Q7 F8 S1 B1
N3 P99.59.59 E99.59 Q9999 F9999 S2 B99
N4 P0.0.0 E0.0 Q0 F0 S0 B0
：
N80 P0.0.0 E0.0 Q0 F0 S0 B0
%
I - 459
(b) Tool life management II

Tool life management II format is as follows.
G Group No. The group No. for tool life management is shown with the
value following G.
M Method The tool life management method is shown with the value
following M.
0: Life management is carried out using the time of cutting
feed execution.
1: Life management is carried out using the number of usages.
Counting the number of usages is executed when changing
from rapid traverse command (G00, etc.) to cutting feed
command (G01,G02,G03, etc.). Note that if rapid traverse
command or cutting feed command that does not involve
any movement is executed, usage will not be counted.
E/F Service life The life data (service lifetime) is shown with the value following
E.
The life data (service life count) is shown with the value
following F.
(Note 1) When the combination of the setting of tool life
management method and address is illegal, error
occurs at data input.
(Note 2) The USED data will be incremented when the LIFE
data is "0", but no judgment if the service life is
reached will be made.
A/B Remaining life [Tool life prediction function valid (#1277 ext13 bit1 is "1")]
The tool life prediction data (remaining lifetime) is shown with
the value following A.
The tool life prediction data (remaining life count) is shown
with the value following B.
(Note 1) When the value greater than the tool life data is set,
tool life prediction signal is not output.
[Tool life prediction function invalid (#1277 ext13 bit1 is "0")]
A and B are not used.
D Tool No. The tool No. is shown with the value following D.
H Compensation No. The compensation No. is shown with the value following H.
P/Q Used The used data (used time) is shown with the value following P
or Q.
The used data (used count) is shown with the value following
P or Q.
S Status The tool status is shown with the value following S.
0: Not used tool
1: Current tool (tool being used)
2: Normal life-reached tool
3: Tool skip tool
I - 460
[Output example]
%
LIFEL2( TOOL LIFE DATA)
$1
G100 M0 E1000 A50 D123456 H1 P321 S1
G100 M0 E1000 A50 D888888 H2 P0 S0
G111 M1 F2000 B80 D777777 H20 Q2000 S2
G1234 M0 E1000 A50 D123 H30 P100 S1
G9999 M1 F999999 B9 D999999 H80 Q999999 S2
%
Data format (Common variable data)
Common variable data format is as follows.

N Variable No. The common variable # No. is shown with the value following
N.
T Part system No. For data per part system, the part system No. is shown with
the value following T.
($1: T1, $2: T2, PLC axis: T3)
P Common variable data The common variable data is shown with the value following P.
An exponential is displayed when 7 digits are set in the integer
section and 5 digits or more are set in the decimal section.
(Example)
1234567 → 1.2346E+006, 0.00001 → 1.0000E-005
[Output example]
%
COMN()
N100T1P123.0000
N101T1P1.0000E7
：
N100T2P1.0000E7
：
%
I - 461
Data format (System configuration data)
System configuration data format is as follows.

Contents of the data are same as that of displayed in the system configuration screen and drive
monitor screen of the diagnosis screen.
[COMMON]
FILE=ASSEMBLY
DATE=04.11.01
Data & time of system configuration data output
TIME=15:30:00
NC_TYPE=MITSUBISHI CNC 750M NC type
(1) NC unit configuration Same as "H/W config" screen
(2) H/W configuration Same as "H/W config" screen
(3) Servo drive unit information Same as "Servo unit" screen
(4) Spindle drive unit information Same as "Spindle unit" screen
(5) Power supply unit information Same as "Power unit" screen
(6) Auxiliary axis information (700 series only) Same as "AUX unit" screen
(7) S/W configuration Same as "S/W config" screen
(8) Ladder configuration Same as "Ladder config" screen
[F_END]
[Output example]
[COMMON] Tag described at the top of the file

FILE=ASSEMBLY Header information of the file (file type)
DATE=04.11.01 File output date
TIME=15:30:00 File output time
NC_TYPE=MITSUBISHI CNC NC type and Lathe(L)/Machining center(M)
750M Tag described at the top of the data
[FILE] Data type (NC unit configuration)
TYPE=NC_UNIT Describe items and data
NC_NAME=FCA750MN
UNIT_NAME=FCA7-MA001
NC_SN=M1234567890 Tag described at the end of the data
[END]
[FILE] Data type (H/W configuration)
TYPE=HARDWARE Repetitive data No. tag (1st)
[DATA1] Describe items and data
HW_NAME=HN145
REVISION=A Repetitive data No. tag (2nd)
[DATA2]
: Repetitive data No. tag (n-th)
[DATAn] Describe items and data
HW_NAME=HN081
REVISION=A
[END]
:
[FILE]
:
[END] Tag indicating file end
[F_END]
I - 462
6.2.11 Edit Lock B and C

This function prohibits editing, erasing, etc., of the machining programs B and C, and protects the machining
programs in NC memory.
Machining program A
1 to 7999
Machining program B
(user standard subprogram)
8000 to 8999
Machining program C Editing Editing
(machine tool builder custom prohibited by prohibited by
program) Edit lock C Edit lock B
9000 to 9999
Machining program A
10000 to 99999999
The operations below in the Edit MDI and the Input/Output screens are influenced by the edit lock setting.
An error will result if operations that are not possible are attempted.
When the edit lock is valid, processing is executed (except the edit lock target program) by the input/output
function.
{ : Operation possible × : Operation not possible

Edit lock B Edit lock C
Screen Operation Machining program Machining program
A B C A B C
Edit Search { { × { { ×
Edit { × × { { ×
MDI registration { × × { { ×
Input/Output Transfer { × × { { ×
Compare { × × { { ×
Copy { × × { { ×
Merge { × × { { ×
Rename { × × { { ×
Erase { × × { { ×
Monitor Buffer correction { × × { { ×
I - 463
6.2.12 Data Protect Keys

The data protect keys can be used to prohibit data setting and erasure. The following three keys are available.
(Their names differ according to the machine tool builder. For further details, refer to the instruction manual
issued by the machine tool builder.)
(1) KEY1: Provides general protection for tool data and protection of the coordinate system preset using
the origin set.
(2) KEY2: Protects user parameters and common variables.
(3) KEY3: Protects the machining program.
Data settings and deletion is stopped if any of the data protection keys is OFF.
Data protection keys CNC data
CNC screen KEY1

Tool data
All data settings KEY2
User parameters
KEY3
Machining program
(Note 1) When using the multi-part system, the settings for various types of data in all part systems are
prohibited with the data protection keys.
Tool data protection (KEY 1)
The operations listed in the table below are prohibited when KEY 1 is OFF.
<Data protected by KEY1 >
No. Operation Screen
1 Origin set Monitor
2 Tool compensation amount setting/erasing Tool compensation amnt, Tool measure
3 Tool registration data setting/erasing Tool registration
4 Tool life data setting/erasing Tool life
5 Workpiece coordinate offset amount setting/erasing Coord offset, Workpiece measure, Rotate meas
6 Tool offset data input/output Input/Output
7 Tool compensation amount input/output Input/Output
8 Tool registration data input/output Input/Output
9 Tool life data input/output Input/Output
10 Workpiece coordinate offset amount input/output Input/Output
(Note) If setting of data in the screens shown in No. 2 to 5 is attempted when the KEY1 is OFF, the message
"Data protect" appears.
If origin set is attempted on the Position display1 screen and the INPUT key is pressed, the origin
set is not executed, and the message "Origin set not possible" appears.
If the operations shown in No. 6 to 10 are attempted and the INPUT key is pressed, the message
"Data protect" appears, and the input and output are disabled.
I - 464
User parameter, common variable protection (KEY 2)
<Data protected by KEY 2>
1 Control parameter ON/OFF Setup/User/Control param
2 Axis parameter setting Setup/User/Axis param
3 Operation parameter setting Setup/User/Operation param
4 Machining parameter setting Setup/User/Process param, Rotate meas
5 Common variable setting Monitr/Position display/Common variable
6 I/O basic parameter setting Mainte/Parameter
7 Parameter input/output Mainte/I/O
8 Common variable input/output Mainte/I/O
(Note) If setting of data in the screens shown above is attempted when the KEY2 is OFF, the message "Data
protect" appears.
If the operations shown in No. 7 and 8 are attempted and the INPUT key is pressed, the message
"Data protect" appears, and the input and output are disabled.
Machining program protection (KEY 3)
<Data protected by KEY3>
1 MDI data memory entry MDI
2 Machining program editing Edit
3 New program editing Edit
4 Registered program comment setting Edit
5 Machining program memory registration, compare, input/output Input/Output
6 Machining program erasing (single, all) Input/Output
7 Registered program comment setting Input/Output
8 Machining program copy, marge, name change Input/Output
9 Machining program buffer correction Monitr
(Note) If editing or setting, etc., is attempted on the screens shown above when the KEY3 is OFF, the
message "Data protect" appears.
I - 465

Operation method
(1) Use the menu Area change to select

file setting column A.
(2) Designate the transfer source device, The designated file appears.

file setting column B.
(4) Press the menu Anshin net to "Anshin-net server" is displayed as device name.
designate the transfer destination device The file name, unless specified, is as same as the
and file name. name of the originally transferred file.
Only numbers within 10 characters can be used for
a file name.
(5) Press the menu Transfr A→B . A message appears to confirm the transmission of
machining data.
(6) Press the Y or INPUT key. Transmission of machining data starts.

A message appears upon the completion of
transmission.
(Note 1) Neither HD operation nor memory card operation can be performed during file transmission from
HD.
(Note 2) Only one file can be saved on Anshin-net server. The file previously exists on the Anshin-net server
is overwritten.
cannot be selected.
I - 466
Receiving machining data from Anshin-net server

(2) Press the menu Anshin net to “Anshin-net server” as device name and the
designate the transfer source device and designated file name are displayed.
file name.

file setting column B.
(6) Press the menu Transfr A→B . A message appears to confirm the reception of
machining data.
When the file name is not designated in the file setting
column A, the message “File name not designated for
dev A” appears to indicate the error.
(7) Press the Y or INPUT key. The reception of machining data starts.
A message appears upon the completion of reception.
(Note 1) When the same file name exists in the transfer destination device, an error occurs and the transfer
cannot be executed.
cannot be selected.
I - 467
Erasing machining data on Anshin-net server

(2) Press the menu Anshin-net to “Anshin-net server”, as device name, and the
designate the file name to erase. designated file name are displayed.
(3) Press the menu Erase A . A message appears to confirm the erasing.
(4) Press the Y or INPUT key. The file will be erased.

A message appears upon the completion of erasing.
Canceling a warning from network service
(Note 1) A warning message from network service appears when any error occurs during communications.
Notes
(1) Transfer to/from Anshin-net server cannot be interrupted.

(2) Only machining program, except fixed cycle and machine tool builder macro, can be transferred to
Anshin-net server.
(3) Data transfer between Anshin-net server and serial (RS232C) or Ethernet is not available.
(4) The edit screen and the maintenance screen can share machining data. However, the machining data
being transferred to/from either of the screens cannot be shared with the other screen.
(5) Wildcard (*) cannot be used for the file name.
(6) The capacity of machining program for transmission is restricted according to the settings of Anshin-net
server.
I - 468
6. Maintenance Screen
6.3 All Backup Screen

This screen is used to perform batch backups of NC memory data to an external device, and batch
restoration of that data to the NC memory.
Data backed up by the automatic backup function can also be restored.
Data which has been automatically backed up can be selected only when the device set by the "#8919 Auto
backup device" parameter setting is selected.
(1)
(2)
(3)
(4)
(5)
Display items

(1) Device name This displays the selected device name.
(2) Data name This displays the data name being backed up/restored.
System data, ladder, and APLC data are displayed.
(3) Execution status This displays the processing execution status.
Processing is executed in the system data, ladder, and APLC data order.
(Note 1)
(4) Warning message This displays messages at the start and end of backup/restore processing.
(5) Backup list This displays the backup date list.
This date is the system data time stamp.
Backup
Backup area Explanation
format
Auto 1 Data that was automatically backed Auto
2 up. Display in the backup date
3 descending order. The latest three
generations of data are displayed.
Manual Data that was backed up on this Manual

screen.
Master data Data that was backed up on this Manual
screen. Generally, this is the factory
settings data.
The above data can be selected at restore processing. (Note 2)
(Note 1) "APLC data" cannot be backed up/restored if the optional "APLC" is disabled.
(Note 2) The "Auto 1 to 3" data display when the device set by the "#8919 Auto backup device" parameter is
selected.
I - 469
Menus
Menu Detail Type Reference

Device This displays the sub-menu for "Device" selection. C
select
Backup This executes backup processing. A 6.3.1 Performing a
Backup Operation
Restore This executes restore processing. A 6.3.2 Performing a
Restore Operation
Stop This stops processing. C
I - 470
6.3.1 Performing a Backup Operation
Operation methods
(1) Press the menu Backup . The menu is highlighted.

An operation message "Select directory to
backup" appears.
(2) Move the cursor to select the area. An operation message "OK? (Y/N)" appears.
Press the INPUT key. (Note) Auto 1 to 3 cannot be selected.
(3) Press Y or INPUT key. Backup operation begins.

An operation message "Backupping" appears.
When the backup is completed without error, an

operation message "Backup complete" appears.
6.3.2 Performing a Restore Operation
Operation methods
(1) Press the menu Restore . The menu is highlighted.

An operation message "Select directory to
restore" appears.
(2) Move the cursor to select the file. An operation message "OK? (Y/N)" appears.
Press the INPUT key.
(3) Press Y or INPUT key. Restore operation begins.

An operation message "Restoring" appears.
When the restoration is completed without error,

an operation message "Restore complete"
appears.
I - 471
6.4 System Setup Screen

The essential data required for the NC's initial startup is automatically set by inputting the minimum
requirement item only on this screen.
This function allows setting data required to drive the motors (servomotors, spindle motor, auxiliary axis
motor) to be specified quickly and easily, resulting in a faster initial startup of the tool machine.
(Note) The auxiliary axis motor is used for 700 series only.
(1)
(2)
(5)
(3)
(4)
Display items

(1) Common setting area
Set the display language for system setup and after setup (after the power is
Language displayed
turned ON again). This setting is registered at the "#1043 lang".
Set the number of spindles connected to the NC.
Number of spindles
This setting is registered at the "#1039 spinno".
Number of MR-J2-CT Set the number of auxiliary axes (MR-J2-CT) connected to the NC.
(700 series only) This setting is registered at the "#1044 auxno".
(2) Setting by system area
Set the number of axes for each part system and PLC.
This setting is registered at the "#1002 axisno".
Number of axes
A setting error occurs if a setting of "1 or higher" is specified for the Nos.2 to 4
part systems when the setting for the previous part system is "0".
Set the command type for each part system. This setting is registered at the
"#1037 cmdtyp".
Command type (Note) Although this setting can be set individually for each part system, it will
be shared by the entire part system if specified for the machining
center.
I - 472

(3) Setting by spindle area
Set the servo I/F connection channel and the rotary switch No. (2-digit value)
for each spindle drive unit. This setting is registered at the "#3031 smcp_no".
Ch / Rotary SW No.
1st digit : Servo I/F connection channel.
2nd digit : Rotary switch No.
Set the power supply types that are connected to each spindle drive unit.
Input the values as indicated at the guidance display area. The input values are
Power Supply type
then converted to, and display as, power supply types.
If "0" is displayed, it means "No connection".
(4) Setting by servo area
Set the servo I/F connection channel and the rotary switch No. (2-digit value)
for each servo drive unit. This setting is registered at the "#1021 mcp_no".
Ch / Rotary SW No.
1st digit : Servo I/F connection channel.
2nd digit : Rotary switch No.
Set the motor types that are connected to each servo axis.
Motor type Input the values as indicated at the guidance display area. The input values are
then converted to, and displayed as, motor types.
Set the encoder types that are connected to each servomotor.
Detector type Input the values as indicated at the guidance display area. The input values are
then converted to, and displayed as, encoder types.
Set the power supply types that are connected to each servo drive unit.
Input the values as indicated at the guidance display area. The input values are
Power Supply type
then converted to, and displayed as, power supply types.
If "0" is displayed, it means "No connection".
(5) Guidance display Indicate the setting content and setting range for the setting item where the
area cursor is positioned.
I - 473
Menus

Param This writes the parameters based on settings on system setup 6.4.2 Writing Initial
setting screen to NC system. A
Parameters
This writes the minimum required setup PLC ladder for manual 6.4.3 Writing
Ladder
setting operation (JOG mode) to NC system. A Sample PLC
This menu is only for 700 series. Ladders
Next This displays the next page when guidance display content
extends through multiple pages. C
guide
Next This displays the PLC axis setting area at the setting by system
area. C
system
Next This displays the 5th axis and following in setting by servo area
when the total number of axis in the part system exceeds 5. C
axis
6.4.1 Preparation for Spindle Parameter Setting

A spindle parameter setting file (INITSP.PRM) must be prepared in advance in order to set all the spindle
parameter settings at once.
Operation methods
(1) Save the spindle parameter setting file at the Assuming that personal computer recognizes the
memory card's root directory. memory card as the E drive, the spindle parameter
setting file is saved as "E: \INITSP.PRM".
(2) Insert the memory card into the front IC card At the input/output screen, verify that the
holder. "INITSP.PRM" file has been saved on the memory
card.
I - 474
6.4.2 Writing Initial Parameters
Operation methods
(1) Enter all the required settings on the system

setup screen.
(2) Press the menu Param setting . The menu is highlighted.

An operation message "Set up parameter? (Y/N)"
appears.
(3) Press the Y or INPUT key. Parameter setting begins, and an operation
message appears as follows.
"Initial parameter creating" → "Initial parameter
transferring" → "Spindle initial parameter
transferring" (This operation message is
displayed only if a spindle parameter setting file
exists.)
When parameter settings are completed, an
operation message "Param set ended. Format
NC memory? (Y/N)" appears.
(4) Press the Y or INPUT key. File formatting begins, and an operation message
"Executing format" appears.
When file formatting is completed, an operation
message "Format complete" appears.
(Note 1) When the "data protect key 2" is enabled, an operation message "Data protect" appears, and
processing is interrupted.
(Note 2) In the automatic operation mode, an operation message "Executing automatic operation" appears,
and processing is interrupted.
(Note 3) If all the required settings have not been input on the system setup screen, an operation message
"Setting error" appears, and processing is interrupted.
(Note 4) Processing is interrupted if a key other than the Y or INPUT key is pressed, or if switching to
another screen occurs. (Processing is interrupted even if switching to another screen occurs during
data transfers.)
(Note 5) The menu is displayed in gray during data transfers.
I - 475
6.4.3 Writing Sample PLC Ladders
Operation methods
(1) Press the menu Ladder setting . An operation message "Write sample ladder?
(Y/N)" appears.
(2) Press the Y or INPUT key. Sample PLC ladder writing begins, and an
operation message "Transferring" appears.
When sample PLC ladder writing is completed, an
operation message "Transfer complete" appears.
(Note 1) In the automatic operation mode, an operation message "Executing automatic operation" appears,
and processing is interrupted.
(Note 2) In the "PLC RUN" mode, an operation message "PLC running" appears, and processing is
interrupted.
(Note 3) If there is no sample PLC ladder, an operation message "Sample ladder not found" appears, and
processing is interrupted.
(Note 4) Processing is interrupted if a key other than the Y or INPUT key is pressed, or if switching to
another screen occurs. (Processing is interrupted even if switching to another screen occurs during
data transfers.)
(Note 5) The menu is displayed in gray during data transfers.
I - 476
6.5 Adjust S-analog Screen

The spindle analog output adjustment is carried out on this screen.
(1)
(2)
(5)
(3)
(4)
Display items

(1) Parameter No. For manual adjustments, this uses the ↑ ↓ keys to move the cursor to
the setting item to be adjusted.
The cursor does not display during automatic adjustments.
(2) Adjustment item This displays the names of the spindle analog adjustment items.
name
(3) Adjustment data This displays the setting data for each adjustment item.
(4) Current adjust data This displays data which is being adjusted manually. (Display only during a
manual adjustment.)
(5) Operation procedure This displays the operation procedures for automatic and manual adjustments.
I - 477
Menus

This carries out automatic adjustment of the spindle analog A 6.5.2 Performing
Auto
adjust output. Automatic
Adjustments
Manual This carries out manual adjustment of the spindle analog output. B 6.5.3 Performing
adjust Manual
Adjustments
Voltage This is used during manual adjustments to adjust downward in C
-10 decrements of 10.
Voltage This is used during manual adjustments to adjust downward in C
-1 decrements of 1.
Voltage This is used during manual adjustments to adjust upward in C
+1 increments of 1.
Voltage This is used during manual adjustments to adjust upward in C
+10 increments of 10.
I - 478
6.5.1 Adjustment Preparations
Operation methods
The PLC must be stopped when performing spindle analog output adjustments.
(1) Press the function key MAINTE . The maintenance screen appears.
(2) Press the menu Psswd input . The menu is highlighted.
(3) Enter the machine tool builder password. The menu highlighting is cleared.
(4) Press the menu PLC STOP . The PLC is stopped.
6.5.2 Performing Automatic Adjustments
Automatic adjustment will execute "0V offset adjustment" and "+ gain adjustment" for the remote I/O analog
outputs (max. 4ch) connected to the main unit. The - gain will be handled as the + gain.
Operation methods
(1) Press the menu Auto adjust . The menu is highlighted.

An operation message "Execute? (Y/N)" appears.
The cursor display clears from the screen.
(2) Press the Y or INPUT key. Automatic adjustment begins, and an operation
message "Auto adjust execution" appears.
The manual adjustment related menu is displayed
in gray during the automatic adjustment, and
manual adjustments are disabled.
Switching to other screens is also disabled at this
time.
When the automatic adjustment is completed, an
operation message "Auto adjust complete"
appears.
I - 479
6.5.3 Performing Manual Adjustments
Adjusting the ch0 0V offset
(1) Use the ↑ ↓ keys to move the cursor to The menu and the selected line are highlighted.
item #10101, then press the Manual adjust The current setting value is displayed at "Current
menu button. adjust data". A 0V analog voltage is output to ch0
at this time.
(2) Monitor the analog voltage. Adjust the 0V offset until the analog voltage is 0V
±3.5mV. The setting range -999 to 999.
(3) <For plus-voltage>

Press the menu Voltage -1 or "Current adjust data" is adjusted downward in
Voltage -10 . decrements of 1 each time the menu Voltage -1
is pressed.
"Current adjust data" is adjusted downward in
decrements of 10 each time the menu
Voltage -10 is pressed.
<For minus-voltage>
Press the menu Voltage +1 or the "Current adjust data" is adjusted upward in
Voltage +10 . increments of 1 each time the menu Voltage +1
is pressed.
"Current adjust data" is adjusted upward in
increments of 10 each time the menu
Voltage +10 is pressed.
"Current adjust data" range is -999 to 999.
(4) Press the INPUT key. "Current adjust data" is set as "ch0 0V offset", and
the 0V offset result is enabled.
The menu Manual adjust highlighting is
cleared.
I - 480
Adjusting the ch0 + gain
item #10102, then press the menu The current setting value is displayed at "Current
Manual adjust . adjust data". A ch0 +10V analog voltage is output
at this time.
(2) Monitor the analog voltage. Adjust the + gain until the monitor voltage is 10V
(3) <For 10V or higher>

Press the menu Voltage -1 or the
Voltage -10 .
<For less than 10V>

Press the menu Voltage +1 or the
Voltage +10 .
(4) Press the INPUT key. "Current adjust data" is set as "ch0 + gain", and
the adjustment result is enabled.
cleared.
Adjusting the ch0 - gain
item #10103, then press the menu The current setting value is displayed at "Current
Manual adjust . adjust data". A ch0 -10V analog voltage is output
at this time.
(2) Monitor the analog voltage. Adjust the - gain until the monitor voltage is -10V
(3) <For -10V or higher>

Press the menu Voltage -1 or
Voltage -10 .
<For less than -10V>
Press the menu Voltage +1 or

Voltage +10 .
(4) Press the INPUT key. "Current adjust data" is set as "ch0 - gain", and
the adjustment result is enabled.
cleared.
I - 481
6. Maintenanace Screens
6.6 Absolute Position Detection Screen
6.6 Absolute Position Setting Screen

The Absolute position setting screen is used to set the data for the absolute position of servo axes including
arbitrary NC axes and PLC axes.
(1)
(8) (2)
(3)
(4)
(5)
(6)
(7)
Display items

(1) Axis name This displays the axis name set with the parameter "#1022 axname2".
The axis name can be switched by Axis select, Next axis, or Prev axis.
(2) Type of zero point This displays the type of zero point initialisation for the selected axis.
initialization The shortened expression of the zero point initialization method selected with the
parameter “#2049 type (type of absolute position detection system)”.
Displayed Type of zero point initialization Setting

expression for absolute position value
1 Inc. Incremental position detection system Other
than
1,2,3,4,
2 With Stopper Dogless-type Machine end stopper 1
absolute position method
3 No Stopper detection system Marked point alignment 2
method
4 Marked point alignment 4
method II
5 Dog-type Dog-type absolute position detection system 3
(3) Progress state
State This displays the progress state of zero point initialisation. (Note)
Machine end This displays the distance from the mechanical basic position to the first grid point.
Machine posn This displays the current machine position. "Not passed" will appear until the axis
passes a grid point for the first time.
(4) Data No. This displays the No., name, and data used to establish the absolute position.
(5) Name • 0 to 2 : Internal data
• 2050 to 2059 : Absolute position parameters
(6) Data
These can be set also in Absolute position parameter screen.
Refer to "Setup Manual" for explanation and setting range of the parameters #2050 to
#2059.
I - 482

(7) Procedures This shows the procedures to establish the coordinate system by zero point
initialization. The contents differ depending on the type of zero point initialisation.
(8) Initialization message This displays a message with the background yellow if an illegal value has been set
for the zero point initialization. Refer to the section "Appendix 6. Alarms" for details.
(Note) [Type of zero point initialization] indicates the progress state of zero point initialization as shown below.
1.Dogless-type absolute position detection system
Machine end stopper method (manual initialization)
Order Display Details of progress
1 Illegality While the absolute position is lost.
2 Stopper From when the menu "Abs pos set" is pressed
to when the axis pushes against the machine end stopper.
3 Release From when the axis pushes against the machine end stopper
to when axis starts to move in the counter direction.
4 Ret. Ref. P. From when the axis moves in the counter direction
to when it reaches the grid point immediately before the stopper.
5 Complete The axis has reached the grid point immediately before the stopper.
The absolute position has been established.
2. Dogless-type absolute position detection system
Machine end stopper method (automatic initialization)
2 Jog Start From when the menu "Abs pos set" is pressed
to when a value is set in "Zero-P".
3 Stopper1 From when JOG operation starts
to when the axis pushes against the machine end stopper.
4 Zero-P. Rel. From when the axis pushes against the machine end stopper
to when axis reaches the approach point.
5 Stopper2 From when the axis reaches the grid point immediately before the stopper
to when it pushes against the machine end stopper.
6 Ret. Ref. P. From when the axis pushes against the machine end stopper second time
to when axis reaches the grid point immediately before the stopper.
7 Complete The axis has reached the grid point immediately before the stopper.
Marked point alignment method
2 Origin Set From when the menu "Abs pos set" is pressed
to when "1" is set in "Origin-P".
3 Ret. Ref. P. While moving in the direction designated with the absolute position parameter #2050.
4 Complete The axis has reached the grid point immediately before the marked point.
Marked point alignment method II
2 Origin Set From when the menu "Abs pos set" is pressed
to when "1" is set in "Origin-P".
3 Complete With the sequence above, the absolute position is established.
5. Dog-type absolute position detection system
2 Zero-P. Rel. After dog-type manual or automatic reference position return is started.
3 Complete Axis has returned to the reference position.
I - 483
Menus

Axis After selecting this menu, set the axis name, and press the INPUT key A 6.6.1 Selecting an Axis
select to display the axis name and related data.
Prev This switches the data display to the previous axis' data A
axis When the first data is displayed, the last axis data will be displayed.
l t
Next This switches the data display to the next axis' data C
axis When the last data is displayed, the first axis data will be displayed.
6.6.1 Selecting the Axis
Procedures
(1) Press the menu Axis select . The menu is highlighted.

The cursor appears in the input area.
(2) Set the axis name (which was set with The axis name and data change.
"#1022 axname2") and press INPUT key. Procedures displays according to the selected initialization
type.
I - 484
6.6.2 Carrying Out Dogless-type Zero Point Initialization
Procedures (Machine end stopper method : manual method)
Set the following parameter beforehand in the "Abs.Posit.Param." screen.

Parameter Setting value
#2049 type (absolute position detection type) 1 (machine end stopper method is selected)
#2054 clpush (current limit) 0 to 100
#2059 zerbas (zero point return parameter) 1 (on the grid point immediately before the stopper)
The parameters other than "#2049 type" can be set in the "Zero point set" screen.
(1) Select the axis that "#2049 type" is "1". Refer to "6.6.1 Selecting the Axis" for procedures to select
the axis.
(2) Select the HANDLE mode or JOG mode.
(3) Input "1" to "Absolute posn set". The input value appears at "Absolute posn set".
(4) Input an arbitrary value to "#2 Zero-P". The input value appears at "#2 Zero-P".
(5) Move the axis toward the machine end State : [Stopper]
stopper. Machine end : Distance between stopper and grid point
-> a
Machine posn : [Not passed] -> current machine position
(6) Hit against the machine end stopper. State : [Stopper]

-> b
The current has reached its limit for given State : [Release]
time.
-> c
(7) Move the axis in the counter direction. State : [Ret. Ref. P.]
-> d
The axis has reached the grid point State : [Complete]

immediately before the stopper.
-> e
This completes zero point initialization. Turn the power OFF
and ON after the initialization for all axes.
I - 485
If "#2059 zerbas" is "0" (absolute position origin point = mechanical basic position), axis will stop
automatically at this point without moving in the opposite direction and "Complete" appears at [State] and
"0.000" at [Machine end].
Initialization start point (5) (6)
(8) (7)
Basic machine coordinate system Reference (9)
zero point position
Grid point Machine end stopper

Zero return parameter (electric basic (Mechanical basic
"#2037 G53ofs" position) position)
"Machine end"
"#2 Zero-P" (#2059 zerbas=1)
"#2 Zero-P" (#2059 zerbas=0)
"#2 Zero-P" depends on the setting of "#2059 zerbas".
(Note1) To change just the basic machine coordinate zero point, set "#0 Absolute posn set" and "#2 Zero-P",
and then turn the power OFF and ON.
(Note2) If pressing against the machine end is attempted without passing the grip point once after turning
the power ON, the operation message "Not passed on grid" will appear. Return to a point before the
last grid, and then repeat from step of pressing against the machine end stopper.
(Note3) If the first grid point is covered by the grid mask (#2028 grmask) as a result of return to the electric
basic position, the axis stops at the next grid point.
Note that zero-point shift amount (#2027 G28sft) is invalid.
I - 486
Procedures (Machine end stopper method : automatic method)

#2049 type (absolute position detection type) 1 (machine end stopper method is selected)
#2054 clpush (current limit) 0 to 100
#2055 pushf (push speed) 1 to 999
#2056 aproch (approach point) 0 to 999.999
#2059 zerbas (zero point return parameter) 1 (on the grid point immediately before the stopper)
the axis.
(2) Select the "Auto init set" mode.
(3) Input "1" to "Absolute posn set". The input value appears at "Absolute posn set".
(5) Start JOG operation. State : [Stopper1]

Machine posn : [Not passed] -> current machine position
The axis moves toward the machine end State : [Stopper1]

stopper at the push speed (#2055).
-> a
The axis pushes against the machine end State : [Zero-P. Rel.]
stopper. After the current reached its limit
for given time, the axis returns toward the
approach point at the "push speed".
-> b
After arrived at the approach point, the State : [Stopper2]

axis moves toward the machine end
stopper at the "push speed".
-> c
The axis pushes against the machine end State : [Ret. Ref. P.]
stopper. After the current reached its limit
for given time, the axis returns toward the
grid point immediately before the stopper
at the "push speed".
-> d
The axis has reached the grid point State : [Complete]

immediately before the stopper.
-> e Machine end : Distance between stopper and grid point

I - 487
If "#2059 zerbas" is "0" (absolute position origin point = mechanical basic position), axis will stop
automatically at this point without moving in the opposite direction and "Complete" appears at [State] and
"0.000" at [Machine end].
Initialization start point Push speed a
Basic machine coordinate system Reference e d

zero point position
Grid point
(electric basic "Machine end"
position) Machine end stopper
Reference position (mechanical basic
parameter position)
"#2037 G53ofs" "#2056 aproch"
"#2 Zero-P" (#2059 zerbas=1)
"#2 Zero-P" (#2059 zerbas=0)
"#2 Zero-P" depends on the setting of "#2059 zerbas".
(Note2) If pressing against the machine end is attempted without passing the grip point once after turning
the power ON, the operation message "Not passed on grid" will appear. Return to a point before the
last grid, and then repeat from step of pressing against the machine end stopper.
(Note4) Acceleration/deceleration during movement at the specified push speed is performed in
smoothing-off (step feed) mode.
(Note5) If "0" is specified for "#2056 aproch" of the absolute position parameters, the machine zero point is
regarded as the approach point.
(Note6) Automatic initialization is interrupted if one of the following events occurs. If it is interrupted, [State]
indicates "Jog Start" (after selecting the "Auto init set" mode if it is caused by mode change), so
restart operation from the step of JOG-start.
• An absolute position detection alarm occurs.
• Operation preparation signal turns OFF.
• The mode is changed.
• The system is reset.
If [State] is "Complete" before automatic initialization is started, "State" returns to "Complete" when
power is turned OFF and ON again without restarting the operation.
I - 488
(Note7) Automatic initialization cannot be started in the following cases. The operation message "Can't
start" will appear if starting is attempted.
• When "#0 Absolute posn set" is not set.
• When the "#2 Zero-P" setting is inappropriate.
• When "#2055 pushf" is not set.
• When "Z71 Abs encoder failure 0005" has occurred.
In the above cases, if the "#2 Zero-P" setting is inappropriate, this means that the relation of "#2
Zero-P" and "#2037 G53ofs" is inappropriate. That is, if "#2 Zero-P" is smaller than the "#2037
G53ofs", the machine end stopper will be located between the basic machine coordinate system zero
point and reference position; this disables automatic initialization. (Refer to the following left figure.)
If "#2 Zero-P " is set to "0", the machine end stopper direction is unpredictable; this also disables
automatic initialization. (Refer to the following right figure.)
Basic machine coordinate Machine end stopper

system zero point Reference (Mechanical basic
position position)
Machine end stopper
(Mechanical basic
"#2 Zero-P" position)
Basic machine coordinate

system zero point
#2037 "G53ofs"
If the "#2 Zero-P" setting is "0", the basic

Looking from the basic machine coordinate system zero point, machine coordinate system zero point is
the reference position is located far beyond the machine end located on the machine end stopper.
stopper, thus the reference position return cannot be carried out. The direction of axis movement is thus
unpredictable.
I - 489
Procedures (Marked point alignment method)

#2049 type (absolute position detection type) 2 (marked point alignment method is selected)
#2050 absdir (basic Z - direction) 0/1
The parameters can be set in the "Zero point set" screen.
the axis.
(2) Select the HANDLE mode, HANDLE-AX

mode, or JOG mode.
(3) Input "1" to "#0 Absolute posn set". The input value appears at "#0 Absolute posn set".
(5) Move the axis toward the mechanical State : [Origin Set]
basic position and align it to the marked Machine posn : [Not passed] -> current machine position
point.
-> a
(6) Input "1" to "#1 Origin-P". The input value appears at "#1 Origin-P".
(7) Move the axis in the direction designated State : [Ret. Ref. P.]
with the parameter "#2050 absdir".
-> b Machine end : Distance between machine basic point
(marked point) and the first grid point
The axis reaches the first grid point. State : [Complete]

-> c
I - 490
Initialization start point a
b Machine end
Basic machine c stopper
coordinate system Reference (Mechanical basic
zero point position position)
Grid point
Zero point parameter (electric basic
"#2037 G53ofs" position)
#2 Zero-P (#2059 zerbas=1) "Machine end"
#2 Zero-P (#2059 zerbas=0)
(Note 1) To change just the basic machine coordinate zero point, set "#0 Absolute posn set" and "#2 Zero-P",
(Note 2) If aligning axis on the marked point is attempted without passing the grip point once after turning the
power ON, the operation message "Not passed on grid" will appear. Return to a point before the last
grid, and then repeat from step of aligning the axis on the marked point.
(Note 3) If the first grid point is covered by the grid mask (#2028 grmask) as a result of return to the electric
(Note 4) Reconfirm the "absdir" setting if the machine does not move in the direction of "#2050 absdir". The
machine will move only in the positive direction when set to “0”, and the negative direction when set
to "1".
I - 491
Procedures (Marked point alignment method II)

#2049 type (absolute position detection type) 4 (marked point alignment method II is selected)
the axis.
(2) Select the HANDLE mode, HANDLE

FEED AXIS SELECT mode, or JOG mode.
(3) Input "1" to "#0 Absolute posn set". The input value appears at "#0 Absolute posn set".
Move the axis toward the mechanical State : [Origin Set]

basic position and align it to the marked
point.
-> a
Input "1" to "#1 Origin-P". The input value appears at "#1 Origin-P".
State : [Complete]
Machine end : 0.000
Machine posn : The value set in "#2 ZERO"
Initialization start point a
Machine end
Basic machine stopper
coordinate system Reference (mechanical
zero point position basic position)
Reference position
parameter
"#2037 G53ofs"
(Note2) If aligning axis on the marked point is attempted without passing the grip point once after turning the
power ON, the operation message "Not passed on grid" will appear. Return to a point before the last
grid, and then repeat from step of aligning the axis on the marked point.
I - 492
6.6.3 Carrying Out Dog-type Zero Point Initialization
Procedures (Marked point alignment method II)

#2049 type (absolute position detection type) 3 (dog-type method is selected)
the axis.
(2) Carry out the manual or automatic State : [Zero-P. Rel.]

dog-type reference position return. Machine posn : Current machine position
Reference position return completes. State : [Complete]

Machine end : 0.000
(Note1) If the dog-type reference position return is interrupted by resetting, the previous state ("Complete"
or "Illegality") will display in the [State] column.
(Note2) With dog-type zero point return, reference position return can be executed again even if the [State]
is "Complete".
6.6.4 Precautions
Precautions common for the initialization operation
(1) The "#0 Absolute posn set" parameter (axis for which zero point is to be initialized) can be set
simultaneously for all axes or individually for each axis.
(2) The "#0 Absolute posn set" parameter cannot be turned OFF with the keys. It is turned OFF when
the power is turned ON again.
(3) "#2 ZERO-P" can be set at any time as long as "#0 Absolute posn set" is set to "1".
(4) The grid point must be passed at least once after turning the power ON before initializing the zero
point. If the grid point has not been passed, the operation message "Not passed on grid" will appear
at the "Machine posn".
(5) When the absolute position is established, the required data will be stored in the memory.
I - 493
Precautions common for the dogless-type absolute position detector
(1) Example of setting "#2 Zero-P" parameter

For the "#2 Zero-P" parameter, set the coordinate value of the absolute position origin point
(mechanical basic position or electrical basic position" looking from the basic machine coordinate
system zero point.
(Example 1) To set the zero point at 50.0mm before absolute position origin point on + end
"#2 Zero-P" = 50.0
Basic machine coordinate Absolute position

system zero point origin point
(Mechanical basic
position or electrical
basic position)
(Example 2) To set the zero point at 400.0mm before the machine basic position or absolute
position origin point on - end.
"#2 Zero-P" = 400.0 Basic machine

coordinate system zero
point
Absolute position (Mechanical basic

origin point position or electrical
basic position)
(Example 3) To set the basic machine coordinate system zero point on the grid point, calculate the
"#2 Zero-P" parameter setting value as shown below using the value displayed at
"Machine end". "Machine end" shows the distance from the mechanical basic position
to the previous grid point.
(Note that when setting the electrical basic position coordinate value in "#2 Zero-P",
the "Machine end" value does not need to be considered.)
To set the third gird point as the zero point when the "Machine end" display is -5.3 at the
+ end basic position. (Example of 10.0mm grid interval.)
"#2 Zero-P" = 25.3
Basic machine coordinate Mechanical basic

position
system zero point
10.0 10.0
"Machine end" = -5.3
I - 494
(2) Setting the reference point

The reference point can be set as shown below by setting the "#2037 G53ofs".
(Example 1) To set the reference point to the same position as the basic machine coordinate
system zero point.
"G53ofs" = 0 Absolute position

Reference point origin point
(Mechanical basic
position or electrical
basic position)
Basic machine "#2 Zero-P"
coordinate system
zero point
(Example 2) To set the reference point at a position 200.0mm to the + side from the basic machine
coordinate zero point.
(To set the basic machine coordinate system zero point 300.0mm front of the
absolute position origin point.)
"G53ofs" = 200.0
Absolute position
Reference point origin point
Basic machine
(Mechanical basic
coordinate system
position or electric
zero point
"#2 Zero-P" = 300.0 basic position)
I - 495
6.7 Auxiliary Axis Test Screen [700 series only]

The absolute position setting and test operations can be carried out by separating the auxiliary axis control
from the PLC.
(1)
(2)
Display items
Display item Details Display items/setting range

(1) Operation explanation The operation method is displayed. Refer to "MR-J2-CT Series SPECIFICATIONS
area AND INSTRUCTION MANUAL" (BNP-B3944) for details.
(2) Setting and display area
Ope. test mode This is highlighted when the absolute position can be initialized or test operation is
possible. This cuts off the signals from the PLC.
Absolute posn set This is highlighted when the absolute position can be initialized.
Form abs posn set This displays the initialization method of Dog/Stopper/Origin
the absolute position set with the auxiliary
axis parameter "#50120 ABS Type".
Status abs posn set This displays the initialization state of the Complete/Illegality/Stopper/Release/Ret.
absolute position. Ref. P./Origin Set/Zero-P. Rel.
Refer to "Display of "Status abs posn set"
" in 6.7.2 for details.
Current station No. This displays the number of the currently This follows the "#50100 station" setting.
stopped station.
Current posn This displays the current coordinate 0 to 360°
position.
Inst station No. This displays the commanded station No. This follows the "#50100 station" setting.
for automatic operation, or the nearest
station No. to be stopped at for manual
operation.
Inst posn This displays the coordinate position 0 to 360°
corresponding to the target station No.
I - 496
Display items Details Display items/setting range

(Continued from the previous page)
Operation mode This displays the currently selected 1: JOG
operation mode. 2: STEP
3: MANUAL
4: HANDLE
5: ZRN (Dog only)
Parameter set This displays the No. of the currently 1: Parameter set 1
selected operation parameter group. 2: Parameter set 2
3: Parameter set 3
4: Parameter set 4
Scale This displays the feed amount scale. 0: 1-fold
Feed amount = 0.001 degree * Scale 1: 10-fold
2: 100-fold
3: 1000-fold
Rotation status This displays the state of the auxiliary Normal Rot/Reverse Rot/Stop
axis.
I - 497
Menus

This designates the auxiliary axis No. for which initialization or test A
Axis
select operation is to be carried out.
After pressing this menu, set the auxiliary axis No. (1 to 6).
This switches ON/OFF for the operation adjustment mode. C
When absolute position initialization set and test operation are carried
out, select the operation adjustment mode.
OpeTest
mode (Note) The operation adjustment mode cannot be selected in the
following cases.
J2CT operation adjustment mode valid signal (R9998/bit0) is OFF.
The auxiliary axis is being executed.
This turns ON absolute position initialization set mode. C
Abs This turns OFF absolute position initialization set mode after the
pos set absolute position initialization set is completed.
This menu can be selected only in the operation adjustment mode.
When the display item "Form abs posn set" is set to "Origin", press C
Origin
pos set this menu at the position to be used as the origin point.
The absolute position will then be set at this position.
The axis is started with forward run. B
(1) For HANDLE
A forward run cannot be started by pressing this menu.
(2) For MANUAL/JOG operation
When this menu is pressed in forward run, the axis stops.
Normal
Rot When this menu is pressed in reverse run, the axis is started with
forward run after it stops at once.
(3) For STEP
Whenever this menu is pressed, forward run is executed by each
feed amount.
This menu can be selected in operation adjustment mode only.
The axis is started with reverse run. B
(1) For HANDLE
A reverse run cannot be started by pressing this menu.
(2) For MANUAL/JOG operation
When this menu is pressed in reverse run, the axis stops.
Reverse
Rot When this menu is pressed in forward run, the axis is started with
reverse run after it stops at once.
(3) For STEP
Whenever this menu is pressed, reverse run is executed by each
feed amount.
This menu can be selected in operation adjustment mode only.
I - 498
6.7.1 Preparation
Before the screen is switched to auxiliary axis test screen, prepare the following things.
(1) Parameter settings

Set the following parameters.
No. Name Details

50102 Cont2 Control bit7 = 1 (Absolute position detection)
parameter 2
Turn the NC power ON again after this parameter is set.
(Note) The alarm "Z70 Abs data error" occurs after the power ON
again.
50120 ABS Type Absolute bit1/bit2 : Select the absolute position detection method.
position
detection Method bit2 bit1 Detail
parameter Dog-type method (Note) 1 This decides the reference
position by the near point
dog.
Mechanical end 0 0 This decides the basic point
stopper method by pushing an axis to
machine end etc. when the
torque (current) limit is set.
Marked point 1 0 This decides the basic point
alignment method by aligning an axis to
machine origin point.
(Note) When bit1 is "1", dog-type method is selected regardless of
bit2 setting.
bit3 : Select the electrical basic position direction at marked point

alignment method.
Direction bit3
Electrical basic position direction + 0
Electrical basic position direction - 1
(2) Release servo OFF/interlock for auxiliary axis.
(3) Turn J2CT operation adjustment mode valid signal (R9998/bit0) ON.
I - 499
6.7.2 Selecting a Device, Directory and File
Operation method (dog type)
(1) Press the menu Axis select , input the If the axis No. that does not exist is designated, an
axis No. error will occur.
(2) Press the menu OpeTestmode . When the J2CT operation adjustment mode valid
signal from PLC is only turning ON while an auxiliary
axis is stopping, the menu OpeTestmode can be
turned ON.
(3) Operation mode is changed to "Zero-P.

Rel.".
(4) Set the "Parameter set" No. If the value other than 1 to 4 is set to "Parameter set",
a setting error will occur.
(5) Press the menu Normal Rot or The absolute position is set automatically.
Reverse Rot, start the axis.
(6) Power ON again.
I - 500
Operation methods (Stopper method)
turned ON.
(3) Press the menu Abs pos set . Status abs posn set : "Stopper"
(4) Operation mode is changed to "HANDLE"

or "JOG".
(6) When the operation mode is HANDLE, If the value other than 0 to 3 is set to "Scale", a setting
set the feed amount per pulse to "Scale". error will occur.
(7) The axis is traveled to machine end Status abs posn set : " Stopper" -> "Release"
stopper.
JOG : Press the menu Normal Rot
or Reverse Rot
HANDLE: Turn the handle.
-> a
(8) The axis travels in the opposite direction

for stopper direction.
-> b
Reach the first grid.

-> c
(9) Power ON again.
When "#50101 Cont1/bitA" is "0" (absolute position basic point = mechanical basic position), the axis will
automatically stop without traveling. When absolute position coordinate zero point is set to mechanical basic
position or other than electrical basic position, the reference position is moved with "#50116 ABS Base
(absolute position zero point)".
Axis movement
a
#50116 ABS Base
Setting distance of absolute position zero point c b
Machine end stopper
When #50101 Cont1/bitA = 1 (Mechanical basic position)
When #50101 Cont1/bitA = 0
Grid
Reference position (Electrical basic position)
I - 501
Operation methods (Marked point alignment method)
turned ON.
(3) Press the menu Abs pos set . Status abs posn set : "Origin Set"
(4) Operation mode is changed to "HANDLE",

"STEP" or "JOG".
(6) When the operation mode is STEP or If the value other than 0 to 3 is set to "Scale", a setting
HANDLE, set the feed amount per pulse to error will occur.
"Scale".
(7) Press the menu Origin pos set , Status abs posn set : "Ret. Ref. P."
designate the basic point.
(8) The axis is traveled to mechanical basic

position, aligned origin point.
JOG/STEP: Press the menu Normal Rot
or Reverse Rot
HANDLE: Turn the handle.
-> a
Reach the first grid. Status abs posn set : "Complete"

-> c
(9) Power ON again.
When "#50101 Cont1/bitA" is "0" (absolute position basic point = mechanical basic position), the axis will
automatically stop without traveling. When absolute position coordinate zero point is set to mechanical basic
position or other than electrical basic position, the reference position is moved with "#50116 ABS Base
(absolute position zero point)".
Axis movement a
#50116 ABS Base

Setting distance of absolute position zero point b Mechanical basic position
#50101 Cont1/bitA = 1
#50101 Cont1/bitA = 0
Reference position Grid

(Electrical basic position)
I - 502
Display of "Status abs posn set"
Depending on the state during operation, the display will change as shown below. Refer to the following table
for details on each display item.
Display of "Status abs posn set"

State/operation
Dog Stopper Origin
Absolute position lost Illegality Illegality Illegality
Absolute posn set ON
Start Stopper Origin Set
Normal Rot or Reverse
Rot
Zero-P. Rel. Zero-P. Rel.
Stopper Release
Stop
Rot
Origin pos set ON Ret. Ref. P.
Start
Rot
Absolute position Complete Complete Complete
established
With operation
Without operation
Display item of
Details
"Status abs posn set"
Illegality This appears when the absolute position has been lost.
Stopper This appears after the absolute position initialization set is started and the
machine end is pushed against.
Release This appears after the machine end is pushed against, and the current limit is
reached continuously for a set time.
Origin Set This appears after the absolute position initialization set is started, and the
origin point is designated moving to the mechanical basic position.
Ret. Ref. P. This appears after the basic point is designated, and the nearest grid is
reached with the "#50120 ABS TYPE" basic point direction movement.
Zero-P. Rel. This appears when the reference position has been returned to with the
dog-type initialization.
Complete This appears when the absolute position initialization set has been
completed.
This displays the state that the absolute position has been established.
(Note) When using position setting methods other than the dog-type method, mechanical end stopper method,
marked point alignment method, the initialization state will be blank.
I - 503
6.7.3 Test Operation
Operation methods
The test operation can be carried out with menu Normal Rot/Reverse Rot by separating the auxiliary axis
control from the PLC.
turned ON.
(3) Select the "Operation mode". If the value other than 1 to 5 is set to "Operation
mode", a setting error will occur.
(4) When the operation mode is STEP or If the value other than 0 to 3 is set to "Scale", a setting
HANDLE, set the feed amount per pulse to error will occur.
"Scale".
(6) Rotate the auxiliary axis. (Start by pressing <JOG>

the menu Normal Rot or Reverse Rot.) Rotation will start in the commanded direction.
When the same menu is pressed again, the axis will
immediately decelerate and stop.
If the Normal Rot menu is pressed during reverse run,
the rotation will stop, and then forward run will start.
<MANUAL>
Rotation will start in the commanded direction.
When the same menu is pressed again, the axis will
be positioned to the nearest station, and will stop.
If the Reverse Rot menu is pressed during forward
run, the rotation will stop, and then reverse run will
start. Note that the rotation cannot be started unless
the absolute position is established.
<INCREMANTAL>
Each time the movement is started, the axis will rotate
by the amount set in the Scale.
Other operations are disabled during movement.
<HANDLE>
The axis is fed with handle rotation.
6.7.4 Precaution
(1) Do not turn "Auto operation "start" command signal (ST) " ON during Ope. test mode.
(2) If the screen shifts other screen, the auxiliary axis mode (Ope. test mode, Absolute posn set) is held.
However, the axis stops if the axis is rotating.
I - 504
6.8 Diagnosis Data Collection Setting Screen

The NC automatically collects diagnosis data based on the "Sampling spec" and "Collecting data select"
settings specified at this screen.
(1)
(2)
(3)
Display items

(1) State Display the history data and sampling data collection status.
History data Display the history data collection status.
History collecting : History data collection is in progress.
History stop : History data collection is stopped.
Sampling data Display the sampling data collection status.
Sampling : Sampling data collection is in progress.
Sampling stop : Sampling data collection is stopped.
Sampling invalid : Sampling data collection is disabled.
(2) Sampling spec Specify the part system, spindle, and servo axes where sampling data is to be
collected.
System Specify the part systems where sampling data is not to be collected.
When "0" is set, sampling is carried out for all part systems.
This setting is ignored if a non-existent part system is specified.
Spindle Specify the spindle where sampling data is not to be collected.
When "0" is set, sampling is carried out for all spindles.
This setting is ignored if a non-existent spindle is specified.
Servo Specify the servo axes where sampling data is not to be collected.
This setting is not system-specific.
When "0" is set, sampling is carried out for all axes.
This setting is ignored if a non-existent servo axis is specified.
I - 505

(3) Collecting data select This selects the diagnosis data to be collected.
(0 : Collected. 1 : Not collected.)
H/W config This selects whether or not H/W configuration data is collected.
S/W config This selects whether or not S/W configuration data is collected.
Key history This selects whether or not key history data is collected.
Alarm history This selects whether or not alarm history data is collected.
PLC I/O history This selects whether or not PLC input/output signal history data is collected.
AC alarm history This selects whether or not AC input power error history data is collected.
Spindle data 1 This selects whether or not spindle current waveform (speed FB, current FB,
current command, position FB, position command, droop) data is collected.
Spindle data 2 This selects whether or not spindle current waveform (driver statuses 1,3,4)
data is collected.
Servo data 1 This selects whether or not servo current waveform (speed FB, current FB,
current command, position FB, position command, droop) data is collected.
Servo data 2 This selects whether or not servo current waveform (detector position Rn, Pn)
data is collected.
Modal This selects whether or not modal information (information for each running
block (block data, G-command modal, workpiece coordinate offset)) data is
collected.
Program data This selects whether or not program data (information for each running block
(program coordinate position, manual interruption amount, command
termination)) data is collected.
Coordinate data This selects whether or not coordinate data (information for each running block
(relative position, machine FB position, machine command position)) data is
collected.
Menus
Start This begins collecting sampling data and history data. A 6.8.1 Performing a
Data Collection
Operation
Stop This stops the sampling data and history data collection A 6.8.2 Stopping a
operation. Data Collection
Operation
Data This stops the sampling data and history data collection A 6.8.3 Clearing a
clear operation, and clears the collected data. Collected Data
I - 506
6.8.1 Performing a Data Collection Operation
Operation methods
(1) Press the menu Start . An operation message "The collection begin?"
appears.
(2) Press Y or INPUT key. Data collection begins, and "History collecting"
and "Sampling" appears in the status column.
6.8.2 Stopping a Data Collection Operation
Operation methods
(1) Press the menu Stop . An operation message "The collection stop?"
appears.
(2) Press Y or INPUT key. Data collection stops, and "History stop" and
"Sampling stop" appears in the status column.
To resume data collection, press the menu
Start .
6.8.3 Clearing a Collected Data
Operation methods
(1) Press the menu Data clear . An operation message "Execute the collection
data clear?" appears.
(2) Press Y or INPUT key. The collected data is cleared.

"Stop" appears in the status column.
To resume data collection, press the menu
Start .
I - 507
II. MACHINE OPERATIONS
This chapter explains the functions and operation method of the machine operation switches for operation
(automatic operation and manual operation) by using the illustration of the machine operation panel.
The actual machine operation and motion vary by machine specification. Refer to the operation manual issued
by the machine tool builder. Use this chapter for reference.
MISCELLA-
SINGLE NEOUS
DRY RUN BLOCK FUNCTION CANCEL
CONTROL IN AUTO ALARM M00 M02 M30 LOCK Z LOCK
UNIT OPERATION ON ON ON ON ON ON
READY
OFF OFF OFF OFF OFF OFF
TOOL LENGTH DETECT OVERRIDE MANUAL MANUAL HANDLE OPTIONAL ORIGINAL

PLAYBACK MEASUREMENT ERROR CANCEL OVERRIDE ABSOLUTE INTERRUPT BLOCK SKIP STOP
ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON
OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
REFERENCE POINT
HANDLE/INCREMENTAL HANDLE FEED RAPID TRAVERSE FEED RATE
MAGNIFICATION AXIS SELECTION OVERRIDE OVERRIDE MANUAL FEED RATE RESET
150 100 X Y Z 4
1000 1 140 160 72.0 140. 0
Y Z 100 130 170 52.0
100 1000 5000 10 50 120 180 31.0
200. 0
270. 0
100 10000 X 4 110 190 21.0 370. 0
100
100 25 90
200 20.0 520. 0
FEED AXIS SELECT
10 80
210
220
14.0
10.0
720.0
1000.0
10 50000 70 230 7.2 1400.0
1 1 60 240 6.2 2000.0 +X +Y +Z +4
1000 50 250 3.7 2700.0
1 100000 40
30
260 2.7 3700.0
270 2.0 5200.0
20 280 1.4 7200.0
10 290 1.0 10000.0
0 300 0 14000.0
% % mm/min
-X -Y -Z -4
HANDLE
SPINDLE OVERRIDE
- 00 + MODE SELECT
10 72 MEMORY
10 10 80 90
MDI RAPID TRAVERSE
70 100
TAPE JOG
60 110 EMERGENCY STOP
HANDLE REFERENCE POINT
50 120 RETURN CYCLE START FEED HOLD
INCREMENTAL
II - 1
1. Operation State
1.1 Operation State Correlation Diagram
1. Operation State
1.1 Operation State Correlation Diagram
The controller operation state changes momentarily according to the program contents or signals from the
operation panel or machine. The operation states are roughly classified into power OFF, not ready, and
ready.
Manual mode operation is enabled in the operation complete state.
(a)
Power OFF state
Power OFF
(b) Power ON
Failure in readiness of operations

Operations not ready state Waiting for readiness of operations (Emergency stop)
Operations ready (d) (d) Problem is resolved (c) Emergency stop
Resolve problem that

Operations ready state caused emergency
(e) (e) stop
Reset process
Reset operations Reset operations
Finished
Reset process-
In automatic operations ing
(e)
Automatic operation is
paused
Automatic
Feed hold (g) (f) operation
is started
CRT operations
Start Input (Machinery preparation)
(f) Automatic
Automatic operation in operation Searching unmodal
progress not ready
state Completed
M02/30
Automatic
Block stop (h) (f) operation
is started
Automatic operation is
stopped
[During operation of the above,

automatic start is not possible.]
Operation state correlation diagram
1.2 Power OFF

The power OFF state means that no power is supplied to the control circuit.
(1) From any other state to power OFF (Transition of operation state correlation diagram (a))
• When POWER OFF signal is input from the machine;
• When power supplied from the machine to controller is turned OFF; or
• When power unit fuse in the controller blows.
II - 2
1. Operation State
1.3 Operations Not Ready
1.3 Operations Not Ready

The operation not ready state means that the system is not ready to run because of the controller itself or the
machine, even though power is supplied to the NC unit control circuit. The RUN READY lamp on the setting
and display unit is OFF.
(1) From power OFF to not ready (Transition of operation state correlation diagram (b))
• When POWER ON signal is input from the machine.
(2) From ready to not ready (Transition of operation state correlation diagram (c))
• When EMG (emergency stop) is displayed on the setting and display unit; or
• When any of the following alarms is displayed on the setting and display unit;
Servo alarm, feedback alarm, excessive error alarm, watch dog, MCP alarm.
1.4 Operations Ready

The operations ready state means that power is supplied to the NC unit control circuit and the system is ready
to run. The READY lamp on the setting and display unit is ON.
The state is furthermore classified into the following four:
1.4.1 Reset
The reset state means that the controller is reset.
(1) From not ready to reset (Transition of operation state correlation diagram (d))
This state is also called initial state.
• When about four seconds has passed after the power is turned ON.
(2) From another ready state to reset (Transition of operation state correlation diagram (e))
• When the RESET key on the setting and display unit is turned ON;
• When external reset signal is input from the machine; or
• When M02 or M30 is executed (depending on the machine specifications).
1.4.2 Automatic Operation in Progress

The automatic operation in progress state means running operations in automatic mode. The IN-AUTO
OPERATION lamp on the machine operation panel is ON.
(1) From another ready state to automatic operation in progress (Transition of operation state correlation
diagram (f))
• When the CYCLE START switch on the machine operation panel is pressed in automatic mode.
1.4.3 Automatic Operation Pause

The automatic operation pause state means that operation or motion temporarily pauses during execution of
one block during the automatic operation start. The AUTO PAUSE lamp on the machine operation panel is
ON and the AUTO START lamp is OFF.
(1) From automatic operation start to automatic pause (Transition of operation state correlation diagram (g))
• When the FEED HOLD switch on the machine operation panel is turned ON; or
• When automatic mode input is out.
1.4.4 Automatic Operation Stop

The automatic operation stop state means that execution of one block is completed and stopped during
automatic operation start. Both the AUTO START and AUTO PAUSE lamps on the machine operation panel
are OFF.
(1) From automatic operation in progress to automatic operation stop (Transition of operation state
correlation diagram (h))
• When the SINGLE BLOCK switch on the machine operation panel is turned ON and execution of the
block is completed; or
• When automatic mode input is changed to another automatic mode input.
! CAUTION
Stay out of the moveable range of the machine during automatic operation. Keep hands, feet and
face away from the rotating spindle.
II - 3
2. Indicator Lamps
2.1 Control Unit Ready
2. Indicator Lamps
2.1 Control Unit Ready
The CONTROL UNIT READY lamp indicates that the control unit is ready to run. The lamp goes OFF at
emergency stop or when an alarm occurs in the drive or operation block.
2.2 In Automatic Operation

The IN AUTO OPERATION lamp is ON from CYCLE START switch turning ON in the automatic operation
mode (memory, tape, or MDI) to the program end after M02 or M30 execution, reset, or emergency stop.
2.3 Automatic Operation Start Busy

The AUTO START BUSY lamp indicates that the controller is executing control in the automatic operation
mode. It is ON from the automatic operation start state entered when the CYCLE START switch is pressed in
the automatic operation mode (tape, memory, or MDI) to the automatic operation start end such as the
automatic operation pause busy state entered when the FEED HOLD switch is pressed or block completion
stop (block stop).
2.4 Automatic Operation Pause Busy

The AUTO PAUSE lamp is ON from AUTO PAUSE switch turning on to AUTO START switch turning ON or
when the mode selection switch is changed from the automatic to manual mode during the automatic
operation.
2.5 Return to Reference Position

Output is executed when the controlled axis arrives at the reference position when manual reference point
return, automatic reference point return, or reference point collation (check).
2.6 Alarm
The ALARM lamp goes ON when an alarm occurs during NC running.
2.7 M00
If M00 given in a program is executed during automatic operation, automatic operation stop is performed after
execution of the M00 block is completed. The M00 lamp is turned ON. (This depends on PLC processing.)
2.8 M02/M30
When M02 or M30 is executed during automatic operation, the NC unit reaches the program end and the
M02 or M30 lamp is turned ON. (This depends on PLC processing.)
II - 4
3. Reset Switch and Emergency Stop Button
3.1 Reset Switch
3. Reset Switch and Emergency Stop Button

3.1 Reset Switch
The controller is reset by turning ON the RESET switch on the machine operation panel or the RESET key on
the setting and display unit. When the RESET switch or key is turned ON while the controller is running, the
following states are to be observed.
(1) If a movement command is being executed, movement stops with deceleration and the remaining
distance in the executing block is cleared.
(2) If miscellaneous function such as M, S, or T is being executed, execution of the miscellaneous function is
interrupted.
(3) The active and buffer memory contents and display are cleared.
(4) If a program error is being occured, the program error state is cleared and the ALARM lamp goes OFF.
(5) If the reset switch is turned ON while the input/output device is running, the power will be cut off.
(6) When the reset switch is turned ON, the modal state will return to its original state.
3.2 Emergency Stop Button

The EMERGENCY STOP button is a red mushroom-shaped pushbutton. The unready state is set by
pressing the EMERGENCY STOP button. During emergency stop, the READY lamp goes OFF and
automatic operation and manual operation do not work. The controller is reset at that time.
If the EMERGENCY STOP button is pressed when a movement command is executed, the moving axis
stops and all other machine motions also stop.
When the EMERGENCY STOP button is released, the READY lamp goes ON in about one second and
operation enable state (READY state) is entered.
When parameter is emergency stop hold type, even if the EMERGENCY STOP button is released, the
emergency stop state is held. To release the emergency stop state, turn ON the RESET switch.
When the EMERGENCY STOP LIMIT switch of each axis works, the same state as when the EMERGENCY
STOP button were pressed may be entered depending on the machine specifications.
! CAUTION
! If the axis overruns or emits an abnormal noise, immediately press the emergency stop button and
stop the axis.
II - 5
4. Operation Mode
4.1 Mode Selection Switch
4. Operation Mode
4.1 Mode Selection Switch
The MODE SELECT switch is used to determine the controller operation mode.
Jog feed mode:

Select the mode to move the controlled axis MODE SELECT
consecutively at manual feedrate. MEMORY
Rapid traverse feed mode: MDI RAPID
TRAVERSE
Select the mode to move the controlled axis TAPE JOG
consecutively at rapid traverse feedrate. REFERENCE
HANDLE
Return to reference point mode: POINT
INCRE-
Select the mode to position the controlled axis MENTAL RETURN
at the machine reference point manually.
Incremental mode:
Select the mode to move the controlled axis for
a given distance.
Handle feed mode:
Select the mode to move the controlled axis by using the manual handle.
Memory Mode:
Select the mode for memory operation.
Tape mode:
Select the mode for tape operation.
MDI mode:
Select the mode for MDI operation.
(Note 1) Refer to the section 1.4 for the running state when a mode is changed to another one during
automatic operation.
4.2 Jog Feed Mode

The jog feed mode enables the machine to be moved by hand consecutively at the feedrate set by using the
MANUAL FEED RATE switch. The jog feed mode is started by using the FEED AXIS SELECT switch.
Refer to the section 5 for the MANUAL FEED RATE switch.
Operation procedure
Using the MODE SELECT switch, select the jog mode.
Using the MANUAL FEED RATE switch, set the feedrate.

The feedrate unit is the travel distance (mm) per minute.
To move the controlled axis, turn on the FEED AXIS SELECT switch. The
controlled axis is moved while the switch is turned on.
When the switch is turned off, the controlled axis stops with deceleration.
(Note 1) When the MANUAL OVERRIDE switch on the operation panel is turned ON, the override value set
by using the FEED RATE OVERRIDE switch takes precedence over the feedrate set by using the
MANUAL FEED RATE switch.
II - 6
4. Operation Mode
4.3 Rapid Traverse Feed Mode
4.3 Rapid Traverse Feed Mode

The rapid traverse feed mode enables the machine to be moved consecutively at rapid traverse feedrate
manually.
The rapid traverse feedrate can be changed its speed in four steps by using the RAPID TRAVERSE
OVERRIDE switch. The rapid traverse feed mode is started by using the FEED AXIS SELECT switch.
(Note 1) Refer to the manual issued by the machine tool builder for the rapid traverse feedrate.
(Note 2) Refer to the section 5 for the RAPID TRAVERSE OVERRIDE switch.
Operation procedure
Using the MODE SELECT switch, select the rapid traverse feed mode.
Using the RAPID TRAVERSE OVERRIDE switch, set arbitrary override value.
To move the controlled axis, turn ON the FEED AXIS SELECT switch. The
controlled axis is moved while the switch is turned ON.
When the switch is turned OFF, the controlled axis stops with deceleration.
(Note 1) The override value set by using the CUTTING FEED OVERRIDE switch is not effective for the rapid
traverse feedrate; when the override value is 0%, the controlled axis does not move.
II - 7
4. Operation Mode
4.4 Reference Point Return Mode

This mode enables a controlled axis to be returned manually to the defined position unique to the machine
(reference point).
The first reference point return after the NC power is turned ON becomes the dog mode. For the second or
later reference point return, the dog mode or high-speed return can be selected by setting a given parameter.
Patterns of reference point return are as shown below.
When reference point return direction is positive (+)
To move in + direction To move in – direction
(–) (+)
Dog
Reference point
When reference point return direction is negative (–)
To move in + direction To move in – direction
(–) (+)
Dog
Reference point
Dog mode reference point return
The steps below describe what happens to the controlled axis when it returns to the reference point for
the first time with the power ON and with the machine in an "operations not ready state" (emergency stop
is engaged or the servo alarm is ON) or when the parameters are selected in the dog mode.
(1) The controlled axis is moved in the direction where the near point detection limit switch and dog
approach each other in the reference point return mode.
(2) When the limit switch kicks the dog, the controlled axis once stops with deceleration.
(3) Next, the controlled axis moves to the reference point at the approach rate set in the parameter.
(4) When it arrives at the reference point, the reference point arrival signal is output.
(5) The reference position establishment signal is output.
High-speed reference point return
If high-speed return is set in a given parameter after dog mode reference point return is executed, then
high-speed reference point return will be made.
II - 8
4. Operation Mode
If the return direction is erroneous in high-speed reference point return, an alarm occurs.
A return is made to the reference point at the rapid traverse feedrate.
Minus Plus
Dog
Reference point
Operation procedure
Using the MODE SELECT switch, select the reference point return mode.
Using the RAPID TRAVERSE OVERRIDE switch, set arbitrary override value.
Check the current Z plus

machine position.
Spindle head
X plus
Coordinate system
Minus position Plus position
Machine table
Plus movement Minus movement
Dog
Reference point
Limit switch
The machine position depends on whether the near point detection limit switch is on the plus or minus
side with the near point dog on the machine table as illustrated above as the reference.
When the limit switch exists on the dog, move to either plus or minus.
Using the FEED AXIS SELECT switch, move the machine.

If the limit switch exists in the minus direction as illustrated above, turn ON a plus
FEED AXIS SELECT switch.
For dog mode reference point return, turn ON the FEED AXIS SELECT switch (+ or -) in the direction
where the dog and limit switch approach each other.
For high-speed reference point return, turn ON the FEED AXIS SELECT switch (+ or -) in the direction
that the spindle head approaches the reference point.
Hold the FEED AXIS SELECT switch ON during reference point return until the machine passes by the
dog (dog mode) or the REFERENCE POSITION ARRIVAL lamp goes ON (high speed return).
II - 9
4. Operation Mode
4.5 Incremental Feed Mode
4.5 Incremental Feed Mode

The incremental feed mode enables the controlled axis to be moved at a given distance selected by using the
HANDLE/INCREMENTAL MAGNIFICATION switch at the manual feedrate when the FEED AXIS SELECT
switch is ON.
Operation procedure
Using the MODE SELECT switch, select the incremental feed mode.
Using the HANDLE/INCREMENTAL MAGNIFICATION switch set a travel

distance.
The controlled axis selected by turning ON the FEED AXIS SELECT switch once is
moved at a given distance.
4.6 Handle Feed Mode

The controlled axis can be moved by turning the manual handle.
The travel distance per graduation of the handle depends on how the HANDLE/INCREMENTAL
MAGNIFICATION switch is set.
The axis that can be moved by using the manual handle is determined by setting the HANDLE FEED AXIS
SELECT switch.
Operation procedure
Using the MODE SELECT switch, select the handle feed mode.
Using the HANDLE FEED AXIS SELECT switch, select the controlled axis to be
moved.
Using the HANDLE/INCREMENTAL MAGNIFICATION switch, set the travel

distance per graduation of the handle.
Move the axis by turning the HANDLE HANDLE
in arbitrary direction. -
00 +
10 72
10 10
II - 10
4. Operation Mode
4.7 Memory Mode
4.7 Memory Mode

In the memory mode, a work program registered in memory is called and automatic operation is executed.
Operation procedure
Call the work program for memory operation by using the setting and display unit.
Check whether or not the work program is called normally.
Using the MODE SELECT switch, select the memory mode.
Set an arbitrary override value by using the switch RAPID TRAVERSE

OVERRIDE, FEED RATE OVERRIDE, SPINDLE OVERRIDE. Normally, set the
value to 100%.
Automatic operation is started by turning ON the CYCLE START switch.
The CYCLE START switch becomes effective when it is once turned ON, then OFF.
To temporarily stop machine motion, turn ON the FEED HOLD switch. The
controlled axes being moved stop with deceleration.
When machine motion is stopped by using the FEED HOLD switch, automatic operation will be restarted
by turning ON the CYCLE START switch.
Memory operation terminates when M02 or M30 in the program is executed. The M02 or M30 lamp on
the machine operation panel is turned ON.
To repeat executing the same program, input the rewind signal by reset & rewind with user PLC.
To forcibly terminate automatic operation, turn ON the RESET switch.
! CAUTION
! Carry out dry run operation before actually machining, and confirm the machining program, tool
offset amount and workpiece coordinate system offset amount.
II - 11
4. Operation Mode
4.8 MDI Operation Mode
4.8 MDI Operation Mode

In the MDI operation mode, automatic operation is executed by using a program set on the setting and
display unit MDI program editing screen.
Operation procedure
The MDI operation follows the memory operation.
Set data on the setting and display unit MDI program editing screen.
Using the MODE SELECT switch, select the MDI mode.
The following steps are the same as the memory operation steps. Refer to 4.7.
(Note 1) When using a 2-part system, the MDI data operation can be switched with the parameters.
#1050 MemPrg Details
The common MDI program for the part system is run in each part
0, 2, 4, 6
system.
1, 3, 5, 7 MDI programs for each part system are run in each part system.
II - 12
5. Operation Panel Switches in Operation Mode
5.1 Rapid Traverse Override

5.1 Rapid Traverse Override
Use the RAPID TRAVERSE OVERRIDE switch to

override the rapid traverse feedrate in automatic or RAPID TRAVERSE OVERRIDE
manual operation.
100
RAPID TRAVERSE OVERRIDE is applicable to the 50
following: 25
Automatic operation: G00, G27, G28, G29, G30 1

Manual operation: Rapid traverse,
reference point return,
%
incremental feed
5.2 Cutting Feed Override
Use the FEED RATE OVERRIDE switch to override

the feedrate in automatic operation (G01, G02, or FEED RATE OVERRIDE
G03 F command) or the manual feedrate of jog feed 140

130
150
160
170
in manual operation in 10% units in the range of 0% 120
110
100
180
190
200
to 300%. FEED RATE OVERRIDE is also 90
80
210
220
70
applicable to the dry run rate in automatic operation.
230
60 240
50 250
40 260
30 270
20 280
10 290
0 300
%
(Note 1) The dry run rate is the movement rate set by using the MANUAL FEED RATE switch by overriding
the programmed feedrate in automatic operation.
(Note 2) Refer to the section 6.5 for feedrate override applied to manual feedrate.
5.3 Manual Feedrate

Use the MANUAL FEED RATE switch to set the feedrate in jog feed mode during manual operation. The
feedrate can be selected among 31 steps from 0 to 14000.0 mm/min.
When the MANUAL OVERRIDE switch (interrupt switch) is turned ON, the override value set by using the
FEED RATE OVERRIDE switch takes precedence over the value set by using the MANUAL FEED RATE
switch.
Manual feedrate (mm/min) MANUAL FEED RATE
100
0. 7.2 72 720 7200 72.0

52.0
31.0
140. 0
200. 0
270. 0
21.0 370. 0
1.0 10.0 100 1000 10000 20.0
14.0
10.0
520. 0
720.0
1000.0
7.2 1400.0
1.4 14.0 140 1400 14000 6.2
3.7
2.7
2000.0
2700.0
3700.0
2.0 5200.0
2.0 20.0 200 2000 1.4
1.0
0
7200.0
10000.0
14000.0
mm/min
2.7 27.0 270 2700
3.7 37.0 370 3700
5.2 52.0 520 5200
II - 13
5.4 Handle/Incremental Feed Magnification
5.4 Handle/Incremental Feed Magnification

Use the HANDLE/INCREMENTAL MAGNIFICATION switch to set the travel distance commanded when
manual handle feed or incremental feed is made.
The travel distances for each axis are listed below.
When B or C is set to the parameter "#1003 iunit", up to 1000 only can be validated.
Movement amount Movement amount

HANDLE/
("#1003 iunit"=B or C) (Other than "#1003 iunit"=B or C) INCREMENTL MAGNIFICATION
1 1 1000 1
100 1000 5000 10
100 10000
10 10 10 100
10 50000
100 100 1
1
1000
100000
1000 1000
5000 5000
10000 10000
50000 50000
100000 100000
5.5 Handle Feed Axis Selection
Use the HANDLE FEED AXIS SELECT switch

HANDLE FEED AXIS SELECT
to select the axis moved by handle operation
when the handle mode is selected. Y Z
X 4
5.6 Manual Pulse Generator
In the manual handle mode, fine feed of the HANDLE

machine can be made by turning the manual
pulse generator. - 10
00
72
10
+
10
The manual pulse generator has 100
graduations per revolution and outputs one
pulse per graduation. The travel distance per
pulse is set by using the HANDLE/
INCREMENTAL MAGNIFICATION switch.
II - 14
5.7 Cycle Start and Feed Hold
5.7 Cycle Start and Feed Hold
Use the CYCLE START switch to start

automatic operation (memory, tape, or MDI).
Automatic operation is executed by turning CYCLE START FEED HOLD
ON the switch. Use also the switch for restart
from stop by the FEED HOLD switch or the
automatic operation stop state.
The CYCLE START switch becomes effective when the switch is turned ON, then OFF.
Use the FEED HOLD switch to temporarily stop automatic operation (for example, deceleration stop of
the control axis during automatic operation). To restart operation, use the CYCLE START switch.
5.8 Feed Axis Selection
Use the FEED AXIS SELECT switch to start FEED AXIS SELECT
the controlled axis during manual operation. +X +Y +Z +4
While the FEED AXIS SELECT switch is held
ON, the selected controlled axis is moved.
When the switch is turned OFF, the controlled -X -Y -Z -4
axis movement stops.
II - 15
6. Operation Panel Switch Functions
6.1 Chamfering

6.1 Chamfering
Chamfering in the thread cutting cycle can be validated/invalidated using an external switch.
6.2 Miscellaneous Function Lock

(1) M, S, T or B function execution can be ignored by turning ON the MISCELLANEOUS FUNCTION LOCK
switch.
(2) M, S, T or B function BCD output is made, but the start signal is not output.
(3) If the MISCELLANEOUS FUNCTION LOCK switch is changed during command execution, automatic
operation stops after the block being executed is terminated. Then, it becomes effective.
6.3 Single Block

(1) When the SINGLE BLOCK switch is turned ON, automatic operation stops after the block being
executed is terminated. That is, automatic operation stops after one program block is executed.
(2) The single block stop point in the fixed cycle mode is fixed according to the fixed cycle.
6.4 Dry Run

(1) When the DRY RUN switch is turned ON, the feedrate set by using the MANUAL FEED RATE switch
takes precedence over the programmed feedrate (F).
6.5 Manual Override

(1) When the MANUAL OVERRIDE switch is turned ON, the override value set by using the FEED
OVERRIDE switch takes precedence over the value set by using the MANUAL FEED RATE switch.
(2) The override value set by using the FEED OVERRIDE switch also takes precedence over the dry run
during automatic operation.
(3) Manual override becomes effective immediately when the switch is turned ON.
II - 16
6.6 Override Cancel
6.6 Override Cancel

(1) When the OVERRIDE CANCEL switch is turned ON, the programmed F command value takes
precedence over the override value set by using the FEED RATE OVERRIDE switch.
(2) It is not effective for manual override.
6.7 Optional Stop

(1) If M01 is programmed, the machine automatically stops by turning ON the OPTIONAL STOP switch.
When the switch is OFF, M01 is ignored and the machine does not stop.
(2) The machine stops after the M01 block is executed.
6.8 Optional Block Skip

When the OPTIONAL BLOCK SKIP switch is turned ON, a block which begins with a slash ( / ) is skipped;
when the switch is OFF, the block is executed. This enables the operator to specify whether or not a block
beginning with a slash ( / ) code is executed.
(Example) When machining two parts as illustrated below, if the following program is prepared and the
machining is done by turning ON the OPTIONAL BLOCK SKIP switch, part (a) is provided; if the
machining is done by turning OFF the switch, part (b) is provided:
Program N1G54 ;
N2G90G81X50. Z-20. R3. F100 ;
/N3X30. ;
N4X10. ;
N5G80 ;
M02 ;
Part (a) Part (b)

Switch ON Switch OFF
N4 N2 N4 N3 N2
II - 17
6.9 Manual Absolute
6.9 Manual Absolute

When the MANUAL ABSOLUTE switch is turned ON, while the program coordinate system is not updated,
the coordinate position is updated by the distance in which the tool has been moved manually. If the switch is
OFF, the program coordinate system is updated when the tool is manually moved.
X
W
Feed hold stop Path on program
(absolute command)
Manual interrupt
(Program coordinate system is not updated by
tool move distance.)
Path after manual interrupt
Passes through the same path as program.
-Y
When MANUAL ABSOLUTE Switch Is ON
X
W
Path on program
Feed hold stop (absolute command)
Manual interrupt
(Program coordinate system is updated by tool
move distance.)
Path after manual interrrupt
Path is shifted by manual interrupt value.

(Origin (zero) is moved.)
-Y
When MANUAL ABSOLUTE Switch Is OFF
II - 18
6.10 Error Detect
6.10 Error Detect

For positioning (G00), machine deceleration check is made before next block movement is started. For
cutting (G01, G02, or G03), the next block is started before the machine reaches the movement command
end point. Thus, the corner part is slightly rounded.
To prevent rounded corners, turn ON the error detect signal. This will cause the machine to decelerate until the
remaining distance falls below the value of the parameter. The next block command is stopped during this time.
This function is equivalent to G09 in the program.
The parameter that is used by the error detect switch and the G09 command for determining the remaining
distance after deceleration for moving to the next command can be set with the setting and display unit.
X axis command
Y axis command
Error detect off
Y axis command
Error detect on
6.11 Follow-up Function

The follow-up function monitors machine motion in the emergency stop state and reflects it in the current
position and workpiece coordinates. Thus, the work program can be continued without re-executing a
reference point return after emergency stop.
6.12 Axis Removal

When the machine receives the axis removal signal, that axis no longer becomes the controlled axis.
Accordingly, the alarm related with axis, such as the stroke end axis, and the servo alarms (excessive errors,
lack of signal, drive alarm, etc.) will be ignored. At the same time, the axis will become interlocked.
(Note) This cannot be used for the absolute position detector specification axis.
6.13 Manual/Automatic Synchronous Feed

While you are using the automatic operation in the automatic operation mode (tape, memory, MDI), you can
simultaneously operate the machine manually (jog, reference point return, incremental feed, handle).
To select the manual mode and automatic mode, refer to the instruction manual issued by the machine tool
builders.
II - 19
6.14 Handle Interruption

6.14.1 Outline
Section 6.14 explains automatic handle interruption, which enables the operator to interrupt movement using
the manual handle in automatic modes (tape, memory, MDI).
Y Tool
X Z Interrupt
10
1 100
Workpiece
Handle feed
Automatic feed
G01 Z __ F
X __ Y __ ;
X __ Y __ ;
X __ Y __ ;
Overlaid feed locus of automatic feed and

handle feed
6.14.2 Interruptible Conditions

(1) The automatic handle interrupt function allows you to interrupt the program manually by selecting the
manual handle mode in automatic mode selection (tape, memory, MDI, etc.). However the interrupt
cannot be executed by the manual handle when an automatic reference point return command (G28,
G29, G30), the thread cutting (G33), or the skip command (G31) has been executed or when tapping in
the tapping cycle.
(2) If automatic operation mode such as tape, memory, or MDI is being selected even when an automatic
operation pause (including a block stop) is established, automatic handle interruption is enabled.
(3) If the axis is moved during dwell (G04) command processing by using automatic handle interruption, the
dwell count operation will stop. A check is made for the completion of the axis movement, then the dwell
count operation continues.
(4) Automatic handle interruption is enabled even if automatic machine lock has been set. If manual
machine lock has been set, the machine does not move; it only updates the POSITION display. If manual
machine lock has not been set, the machine moves by the interruption distance by the manual handle
and the POSITION display is updated.
(5) This function is disabled for an axis to which the interlock signal has been input or an axis of which
interruption direction is the soft limit.
6.14.3 Interruption Effective Axis

(1) Automatic handle interruption is enabled only for axes to which manual handle axis selection has been
input.
(2) Automatic handle interruption is enabled for a maximum of three axes. (The number of axes is restricted
by the number of handles.)
II - 20
6.14.4 Axis Movement Speed Resulting From Interruption

(1) The movement speed (Automatic-start movement speed + Speed resulting from manual handle
interruption.) of the axis for which handle interruption is executed, may exceed the rapid traverse feed
rate during rapid traverse feed command (G00) processing in automatic start. To prevent this, clamp the
axis.
(2) The movement speed (Automatic start movement speed + Speed resulting from manual handle
interruption.) of the axis for which handle interruption is executed, may exceed the cutting feed speed
during cutting feed command (G01, G02, G03) processing in automatic start. To prevent this, clamp the
axis.
(3) If, during automatic start, manual handle interruption is executed in the same direction for the axis that is
moving at an external decelerating speed, the axis movement speed (Automatic start movement speed +
Speed resulting from manual handle interruption.) may exceed the external decelerating speed. To
prevent this, clamp the axis.
(4) If an attempt is made to execute interruption at a speed exceeding the clamp speed, the reading on the
handle scale does not match the distance of interruption.
(5) The handle scale factor depends on the selected input of the manual handle/step scale factor.
6.14.5 Path Resulting After Handle Interruption

(1) For incremental (G91) mode
The locus deviates from the program path by the distance of interruption. (See the figure below.)
Program path
(G91 X_ Y_;)
Path after interruption
Distance of interruption by manual handle

(Incremental mode)
(2) For absolute (G90) mode

If program absolute position update by the distance of handle interruption is disabled, the locus deviates
from the program path by the distance of interruption.
If this update is enabled, the locus returns to the program path during processing of the following
command:
For single block running - Return command is issued in the block next to the one for which the
interruption has been completed.
For continuous running - Return command is issued in the third block, if the block for which the
interruption has been completed is the first block.
(Note) Both POSITION and MACHINE display include the distance of handle interruption.
For automatic handle interruption, select whether absolute mode is updated or not, as follows:
(a) Using machine parameters, set whether the manual absolute changeover switch or parameters
are used.
(b) If the parameters are used, set whether or not absolute position data is updated for each axis, by
using machine parameters other than those in item.
(c) If the manual absolute changeover switch is used, use the machine operation panel switch for
selection.
II - 21
Absolute position update conditions for automatic handle interruption

Drive monitor screen
Absolute data update manual interruption
distance display
Parameter ON Absolute position is
Not updated.
#1145 I_abs ON Parameter "#1061 "1" updated.
"1" intabs" (Every axis) OFF Absolute position is
Updated.
"0" not updated.
Absolute position is
PLC interface ON Not updated.
OFF manual absolute updated.
"0" switching Absolute position is
OFF Updated.
not updated.
Program path
(G90 X_ Y_;)

(Absolute mode, program absolute position update invalid)
Program path
(G90 X_ Y_;)

(Absolute mode, program absolute position update valid, single block operation)
II - 22
Program path
(G90 X_ Y_;)
Distance of interruption by
manual handle
Program path
(G90 X_ Y_;)
B
A

A Distance of
interruption in
block execution
B Distance of interruption in block execution

(Absolute mode, program absolute position update valid, continuous operation)
6.14.6 Handle Interruption in Tool Radius Compensation

Special movement described below relates only to the tool radius compensation plane axis. It has no
influence on the other axes.
At time of tool radius compensation (G41, G42):
In incremental mode (G91) - The quantity of deviation equals the distance of interruption.
In absolute mode (G90) - If handle interruption is executed in the block for which tool radius compensation
(G41, G42) is being executed, the proper tool path will return in the succeeding block. This rule applies only
when the program absolute position update is valid during single block running. If program absolute position
update is valid during continuous running, the proper tool path will return at the fourth block after the one
where the interruption has been completed.
If there is no G block existed between the block where the interruption has been completed and the block that
contains the tool radius competition cancel command (G40), the proper tool path will return at the block next
to the tool radius compensation cancel command (G40).
II - 23
Program path
G42
Tool path
manual handle
(Incremental mode, continuous operation)
Program path
G42 G40
R
R
Tool Tool path
R
radius
manual handle

(Absolute mode, program absolute position update valid, single block operation)
Program path
G42 G40
R R
Tool
radius Tool R
path
Distance of interruption
by manual handle

II - 24
Program path
G42 G40
Tool path
Distance of interruption
by manual handle
6.14.7 Interrupt Amount Reset

Interrupt amount is reset when
(1) Dog reference point return is executed;
(2) Emergency stop is released;
(3) Reset rewind or reset 2 is executed; or
(4) Reset 1 is executed when the setup parameter "#1151 rstint" is ON.
6.14.8 Operation Procedure

An operation example is given on the assumption that auto operation of XYZ axes is executed in the memory
operation mode and the Z axis is used as a handle interrupt axis.
Perform automatic operation.
Turn ON the HANDLE INTERRUPT switch on the machine operation panel.
Select interrupt axis by setting the HANDLE AXIS SELECTION switch on the
machine operation panel.
Select the travel distance per handle graduation by setting the HANDLE/
INCREMENTAL MAGNIFICATION switch.
Turn the manual handle in the + or −

direction and change the Z axis cut depth Z
amount.
X
Program path
Tool path (current position
(handle interrupt display) display)
Handle interrupt
When M02 or M30 is executed, automatic operation will stop.
II - 25
6.15 Machine Lock
6.15 Machine Lock

(1) When the "ALL AXES MACHINE LOCK" switch is turned ON, the NC commands for the manual
operation or automatic operation movement can be executed without moving the machine.
The current position display on the setting and display unit will be counted.
(2) The automatic operation speed during machine lock can be selected as the commanded speed or
machine lock speed using the parameters.
• Commanded speed - The movement is executed at the feedrate commanded in the program.
Thus, the time is the same as actual machining.
• Machine lock speed - The movement commands are processed at the rapid traverse rate, and
the dwell time, etc., is ignored. Thus, the program check, etc., can be
carried out faster.
(3) If the "ALL AXES MACHINE LOCK" switch is changed during automatic operation, the automatic
operation will stop after the block currently being executed is completed, and then the setting will be
validated.
(4) During reference point return (G28, G30), the movement will be controlled with the machine lock status
up to the middle point. The machine lock status will be ignored from the middle point to the reference
point.
(5) If the "MACHINE LOCK" switch is changed during manual operation, the setting will be validated after
the feed is stopped once.
(6) The M, S, T and B commands are executed according to the program.
(7) When the "MACHINE LOCK" is turned OFF after the axis is moved in the "MACHINE LOCK" ON state,
the current position display and the machine position will not match.
If AUTO START is pressed in this state, the difference between the current position and the machine
position will be added to the movement amount.
If RESET is pressed, the current position display will be changed to match the machine position. Thus,
after turning "MACHINE LOCK" OFF, press RESET before starting operation.
II - 26
6.16 Deceleration Check

6.16.1 Functions
The purpose of the deceleration check is to reduce the machine shock that occurs when the control axis
feedrate is suddenly changed, and prevent corner roundness. The check is carried out at block joints.
(1) Deceleration check during rapid traverse
The deceleration check is always carried out at the block joints (before executing the next block) during
rapid traverse.
(2) Deceleration check during cutting feed
The deceleration check is carried out at the block joints (before executing the next block) during cutting
feed when any one of the following conditions is valid.
(a) When the error detect switch is ON.
(b) When G09 (exact stop check) is commanded in the same block.
(c) When G61 (exact stop check mode) has been selected.
(3) Designating deceleration check
The deceleration check by designating a parameter includes ″deceleration check specification type 1″
and ″deceleration check specification type 2″. The setting is selected with the parameter ″#1306
InpsTyp″.
(a) Deceleration check specification type 1 (″#1306 InpsTyp″ = 0)
The G0 and G1 deceleration check method can be selected with the base specification parameter
deceleration check method 1 ″#1193 inpos″ and deceleration check method 2 ″#1223 aux07/bit1″.
Rapid traverse Other than rapid traverse command
Parameter Parameter
command (G1 : other than G0 command)
G0→XX #1223 AUX07
#1193 Inpos G1+G9→XX G1→XX
(G0+G9→XX) (BIT-1)
Command Command
0 0 No deceleration
deceleration check deceleration check
check
1 In-position check 1 In-position check
(Note 1) XX expresses all commands.

(Note 2) ″#1223 aux07″ is the part system common parameter.
(b) Deceleration check specification type 2 (″#1306 InpsTyp″ = 1)

Rapid traverse and cutting feed in-position are designated with the parameter ″#1193 inpos″.
Parameter Command block
#1193 Inpos G0 G1+G9 G1
Command deceleration Command deceleration
0 No deceleration check
check check
1 In-position check In-position check No deceleration check
(Note 1) ″#1193 inpos″ is the parameter per part system.

(Note 2) ″G0″ means the rapid traverse, and ″G1″ means the cutting feed.
II - 27
6.16.2 Deceleration Check Method

(1) Command deceleration check
After interpolation for one block has been completed, the completion of the command system
deceleration is confirmed before execution of the next block.
The time required for the deceleration check is determined according to the acceleration/deceleration
mode and acceleration/deceleration time constant.
(a) For linear acceleration/deceleration
Preceding block Succeeding block
Ts Ts : Acceleration/deceleration time constant

Td : Deceleration check time
Td
Td = Ts + (0 to 14ms)
(b) For exponential acceleration/deceleration
Ts
Ts : Acceleration/deceleration time constant
Td Td : Deceleration check time
Td = 2 × Ts + (0 to 14ms)
(c) For exponential acceleration and linear deceleration
2 × Ts
Td Ts
Ts : Acceleration/deceleration time constant
Td : Deceleration check time
Td = 2 × Ts + (0 to 14ms)
The deceleration check time required during rapid traverse is the longest rapid traverse deceleration
check time of all axes. This check time is determined by the rapid traverse acceleration/deceleration
mode and rapid traverse acceleration/deceleration time constant of simultaneously commanded
axes.
The deceleration check time required during cutting feed is determined in the same manner. It is the
longest cutting feed deceleration check time of all axes. This check time is determined by the cutting
feed acceleration/deceleration mode and cutting feed acceleration/deceleration time constant of
simultaneously commanded axes.
II - 28
(2) In-position check

When the in-position check is valid, the command deceleration check is carried out. After that, it is
confirmed that the servo system positional error is less than the parameter setting value, and the next
block is executed.
The in-position check width can be designated with the servo parameter in-position width (SV024).
Note that G0 and G1 can be designated independently with the axis specification parameter G0
in-position check width (G0inps) and G1 in-position check width (G1inps). If both the servo parameter
and axis specification parameter are set, the larger value will have the priority.
Speed
G0inps (G1inps)
SV024
Command to motor
Motor speed
Next block command

Time
Judge completion of
deceleration with G0inps
(G1inps) setting value
ON
Deceleration check signal
OFF
If the SV024 setting value is larger, in-position check will end when the SV024 setting value is
established.
II - 29
6.16.3 Deceleration Check When Opposite Direction Movement Is Reversed

Deceleration check cannot be designated for G1 → G0 or G1 →G1, but it can be designated in the following
manner only when the movement reverses to the opposite direction in successive blocks. Deceleration check
can also be executed if even one axis is moving in the opposite direction while several axes are interpolating.
(1) Designating deceleration check for G1 → G0 opposite direction movement reversal

If the axis movement reverses to the opposite direction in a G1 to G0 successive block, the deceleration
check for the movement in the opposite direction can be changed with the base specification parameter
G1 → G0 deceleration check (#1502 G0Ipfg).
Same direction Opposite direction

The acceleration is
excessive due to the G1
and G0 composite speed.
G0Ipfg:0
G1 G0
G1 G0
G0Ipfg:1 G1 G0
G1 G0 Commanded
deceleration
(2) Designating deceleration check for G1 → G1 opposite direction movement reversal

If the axis movement reverses to the opposite direction in a G1 to G1 successive block, the deceleration
check for the movement in the opposite direction can be changed with the base specification parameter
G1 → G1 deceleration check (#1503 G1Ipfg).
Same direction Opposite direction

The acceleration is
excessive due to the G1
and G1 composite speed.
G0Ipfg:0
G1 G1
G1 G1
G0Ipfg:1 G1 G1
G1 G1 Commanded
deceleration
II - 30
6.16.4 Parameters
(1) Designation of deceleration check
Base specification parameters
# Items Details Setting range
1193 inpos Change with the "#1306 InpsType" (deceleration check designation type).
0: Deceleration check method1
1: Validate in-position check
Deceleration Select the G0 deceleration check method. 0/1

check method 1 0: Command deceleration check
1: In-position check
Validate Designate the deceleration confirmation method for the 0/1
in-position check positioning and cutting command.
0: G0, G1+G9 Command deceleration check
1: G0, G1+G9 In-position check
1223 aux07 Deceleration Select the deceleration check method for G1 + G9. 0/1
(bit1) check method 2 0: Command deceleration check when G1+G9
1: In-position check when G1+G9
Deceleration check is executed only for G1+G9.
If the "#1306 InpsType" (deceleration check designation
type) is "1" (deceleration check designation type 2), this
parameter will be invalid.
1306 InpsTyp Deceleration Select the parameter designation type for the G0 or G1 0/1
check deceleration check.
designation type 0: Deceleration check designation type 1
G0 is specified with "#1193 inpos", and G1+G9 with
"#1223 aux07/BIT1".
1: Deceleration check designation type 2
G0 or G1+G9 is specified with "#1193 inpos".
(2) Deceleration check during opposite direction travel

Base specification parameters
1502 G0Ipfg G1 → G0 0: Do not perform a deceleration check when the 0/1
deceleration movement direction is changed from G1 to G0.
check 1: Perform a deceleration check when the movement
direction is changed from G1 to G0.
1503 G1Ipfg G1 → G1 0: Do not perform a deceleration check when the 0/1
deceleration movement direction is changed from G1 to G1.
check 1: Perform a deceleration check when the movement
direction is changed from G1 to G1.
II - 31
(3) Designation of in-position check width

(a) Servo parameter
2224 SV024 In-position Set the in-position detection width value. 0 to 32767
INP detection width Set the accuracy required of the machine. (µm)
The positioning accuracy increases when the setting
value is lowered, but the cycle time will increase. Set
"50" for the standard value.
(b) Axis specification parameter

2077 G0inps G0 in-position When an in-position check is performed for G0, this 0.000 to
width parameter is valid. 99.999 (mm)
(Comparison of SV024 and this parameter, the
parameter that the in-position width is wider is applied.)
When 0 is set, this parameter is invalid.
(Applicable only to SV024)
2078 G1inps G1 in-position When an in-position check is performed for G1, this 0.000 to
width parameter is valid. 99.999 (mm)
(Comparison of SV024 and this parameter, the
parameter that the in-position width is wider is applied.)
When 0 is set, this parameter is invalid.
(Applicable only to SV024)
6.16.5 Precautions
(1) Designating deceleration check
• When in-position check is valid, set the in-position width in the servo parameters.
(2) Deceleration check for opposite direction movement reversal

• When deceleration check is valid (G0Ipfg=1), deceleration check will be executed when the axis
reverses its movement to the opposite direction at the G1 → G0 successive block regardless of
whether G0 non-interpolation is ON or OFF.
• When deceleration check is valid (G0Ipfg=1), deceleration check will be executed when the axis
reverses its movement to the opposite direction at the G1 → G0 successive block even in the fixed
cycle.
• In the G1 → G28, G1 → G29 or G1 → G30 successive blocks, deceleration check will always be
executed when the G1 movement is completed, when movement to the intermediate point is
completed and when movement to the return point is completed. Note that if the base specification
parameter's simple zero point return "#1222 aux06/bit7" is valid, the base specification parameter G1
→ G0 deceleration check (G0Ipfg) will be followed when the G1 movement is completed and when
movement to the intermediate point is completed. (Deceleration check will always be executed when
movement to the return point is completed even in this case.)
(3) Designating in-position width

• The in-position width (programmable in-position check width) designated in the machining program has
a priority over the in-position width set in the parameters (SV024, G0inps, G1inps).
• When error detect is ON, in-position check will be forcibly carried out.
II - 32
(4) Deceleration check in G1 → G0, G1 → G1 opposite direction movement reversal during

high-speed machining mode
• When the axis movement reverses to the opposite direction in a G1 → G1 successive block during the
high-speed machining mode, the commanded deceleration will not take place even if G1Ipfg is set to 1.
Note that the G0Ipfg setting will be followed if the axis direction reverses to the opposite direction in a
G1 → G0 successive block.
(5) Deceleration check in movement including spindle/C-axis

• The deceleration check for spindle/C-axis movement command is as described in the table below.
That is because a vibration and so on occurs in the machine when the position loop gain (#13002
PGN) is changed during the axis movement.
Rapid traverse Other than rapid traverse command

Parameter Parameter
command (G1 : other than G0 command)
G0→XX #1223 AUX07 G1→G0
#1193 Inpos G1→G1
(G0+G9→XX) (BIT-1) (G1+G9→XX)
Command deceleration
0 0 In-position check No deceleration
check
(Applicable only to SV024) check
1 In-position check 1
(Note 1) When G1 command is issued, the in-position check is performed regardless of the deceleration
check parameter.
(Note 2) XX expresses all commands.
(6) Deceleration check in polar coordinate interpolation / milling interpolation / cylindrical start /
cancel command
• The deceleration check in polar coordinate interpolation / milling interpolation / cylindrical start / cancel
command are as follows.
Parameter: #1223 aux07 BIT1 Deceleration check method

0 Command deceleration check
1 In-position check
II - 33
7. Stored Stroke Limit
Outline
Three tool entry prohibited ranges can be set with stored stroke limit I, stored stroke limit II, IIB and stored
stroke limit IB. Part of the prohibited range on the outside of soft limit I can be validated with stored stroke limit
IC.
The stored stroke limit II and IIB select the outer side (II) and inner side (IIB) of the entry prohibited range with
parameters.
Stored stroke limit IB
Stored stroke limit IIB
Stored stroke
limit IC
Stored stroke limit I
If the tool tries to move over the set range, an alarm will appear, and the axis will decelerate to a stop.
If the prohibited range is entered and an alarm occurs, movement will be possible only in the direction
opposite the entry direction.
[Valid Conditions of Stored Stroke Limit]

When using the relative position detection system, the stored stroke limit is invalid until the reference point
return is completed after the power is turned ON.
The stored stroke limit can be validated even if the reference point return is not yet completed, by setting
parameter #2049 type = 9.
If the absolute position detection is valid when using the absolute position detection system, the stored stroke
limit will be validated immediately after the power is turned ON.
[Stored stroke limit coordinates]

The stored stroke limit check is carried out in the basic machine coordinate system established by the
reference point return. To validate the stored stroke limit even when the reference point return is not yet
completed, check the stored stroke limit using the temporary basic machine coordinate system (basic
coordinate system defined when the power was previously turned OFF).
When the 1st dog-type reference point return is completed after the power is turned OFF, the correct
coordinate system is established.
! CAUTION
Always set the stored stroke limit. Failure to set this could result in collision with the machine end.
(Note) The axis movement possible when the reference point return has not yet completed is limited to
manual and handle feed only. Automatic operation is validated after the reference point return is
completed.
II - 34
Detailed explanation
The stored stroke limit sets a prohibited range with the parameters or program command. The maximum and
minimum values of the prohibited range are set as coordinate values (radius values) on the basic machine
coordinate system for each axis. If the parameters (#8204 OT-CHECK-N and #8205 OT-CHECK-P), for
setting the prohibited range, are set to the same value, the stroke will not be checked. This function is valid
only for the axis for which the reference point is established.
If the machine enters the prohibited range, an operation error will occur, and the machine movement will stop.
The alarm can be reset by moving the erroneous axis in the opposite direction.
During automatic operation, if an alarm occurs with even one axis, all axes will decelerate to a stop. During
manual operation, only the axis that caused the alarm will decelerate to a stop. The axis will always stop at a
position before the prohibited range. The distance between the prohibited range and stop position will depend
on the feedrate.
The stored stroke limits I, II, IIB, IB and IC are handled as follows.
Prohibited Range setting

Type Explanation Validating conditions
range parameter
I Outside • Set by the machine maker. #2013 OT- • Zero point return is
• When used with II, the narrow range #2014 OT+ completed.
designated by the two types becomes the • #2013 and #2014 are not
movement valid range. set to the same value.
II Outside • Set by the user. • #8210 #8204 • Zero point return is
• Select II or IIB with the OT-INSIDE:0 OT-CHECK-N completed.
parameters. • Used with I. #8205 • #8204 and #8205 are
OT-CHECK-P
IIB Inside • #8210 not set to the same
OT-INSIDE: 1 value.
• #8202 OT-CHECK OFF: 0
IB Inside • Set by the machine maker. #2061 OT_1B- • Zero point return is
#2062 completed.
OT_1B+ • #2061 and #2062 are not
set to the same value.
IC Outside • Set by the machine tool builder. #2061 OT_1B- • #2061 and #2062 are not
#2062 set to the same value.
OT_1B+ • #2063 OT_1C type: 2
II - 35
7.1 Stored Stroke Limit I
7.1 Stored Stroke Limit I
This is a stroke limit function used by the machine maker. The boundary is set with the parameters (axis
specification parameters "#2013 OT-" and "#2014 OT+"). The outside of the set boundary is the prohibited
range.
When used with the stored stroke limit II function, the narrow range designated by the two types becomes the
movement valid range.
Point 1
Basic machine coordinate system The following values are set

with the coordinate values in
Prohibited range
Prohibited range
the basic machine coordinate
Machine movement valid range system.
Point 1: #2014 OT+
Point 2: #2013 OT-
Point 2
- setting value + setting

value
II - 36
7.2 Stored Stroke Limit II
The boundary is set with the parameters (axis parameters #8204 OT-CHECK-N, #8205 OT-CHECK-P) or
with the program commands. Either the inside or the outside of the set boundary is the prohibited range.
Whether the inside or outside of the range is prohibited is determined by parameter (#8210 OT-INSIDE).
When the inside is selected, this function is called stored stroke limit IIB.
When using program commands, entry of the tool into the prohibited range is prohibited with G22, and entry
into the prohibited range is enabled with G23.
The stored stroke limit II function can be invalidated for each axis with the parameter setting (#8202
OT-CHECK OFF: 1).
"#8210 OT-INSIDE" can be set for each axis, but when used in combination, the following type of operation is
possible.
X Z Movement prohibited range

Outside
Outside
Moveable range
Moveable range
Outside
Inside
Moveable range
Inside
Inside
Moveable range
II - 37
Stored stroke limit II (When prohibited range is on outside)
When used with the stored stroke limit I function, the narrow range designated by the two types becomes the
movement valid range.
Point 1
Point 3 The following values are set

Basic machine the basic machine coordinate
Range coordinate system system.
Prohibited range
Prohibited range
prohibited with Point 3 and 4:
stored stroke #8205 OT-CHECK-P
limit II Machine movement
valid range #8204 OT-CHECK-N
Point 2 Point 4 Points 1 and 2 are the

prohibited range set with
- setting value + setting stored stroke limit I.
value
Stored stroke limit IIB (When prohibited range is on inside)
A range except for that of the stored stroke limit I becomes the movement prohibited range.
Point 1
Point 3
Basic machine
Range prohibited coordinate system
Prohibited range
Prohibited range
with stored stroke

limit IIB Machine movement
valid range
Point 4
Point 2 - setting value
+ setting value
II - 38
7.3 Stored Stroke Limit IB
7.3 Stored Stroke Limit IB
The boundary is set for each axis with the parameters (axis parameters "#2061 OT_1B-" and "#2062
OT_1B+"). The inside of the set boundary is the prohibited range.
Point 1 The following values are set

Point 3 Point 5 with the coordinate values in
system.
Point 6 Basic
Range prohibited machine
Point 3 : #2062 OT_1B+
Prohibited range
Prohibited range
with stored stroke coordinate Point 4 : #2061 OT_1B-
limit IIB Machine system
movement Points 1 and 2 are the
valid range prohibited range set with
Point 4 stored stroke limit I, and points
3 and 4 are the prohibited
Point 2 - setting value range set with stored stroke
limit II.
+ setting value
7.4 Stored Stroke Limit IC
The boundary is set for each axis with the parameters (axis parameters "#2061 OT_1B-" and "#2062
OT_1B+"). The inside of the set boundary is the machine movement valid range.
This is valid when the axis parameter #2063 is set to 2, and cannot be used with soft limit IB.
Point 1
The following values are set

Prohibited range
Basic machine coordinate system

the basic machine
Prohibited range
coordinate system.
Point 3 : #2062 OT_1B+
Machine movement valid range Point 4 : #2061 OT_1B-
Point 3
Points 1 and 2 are the
prohibited range set with
Point 2 Additional stored stroke limit I.
movement
range
Point 4
II - 39
7.5 Movable Range during Inclined Axis Control
7.5 Movable Range during Inclined Axis Control
By setting #2063 OT_1Btype to "3", the inclined axis control axis can be checked with the program
coordinates using the stored stroke limit IB/IC range setting (#2061, #2062). The stored stroke limit IB and IC
cannot be used together at this time.
By using this function with stored stroke limit I, the check can be carried out simultaneously with the actual
axis and program coordinate value. In this case, the range that does not fit into either of the following two
prohibited ranges will be the movable range.
X axis
i i
Point 3
The following values are set
Point 1 system.
y axis Point 3: #2062 OT_1B+
θ Point 4: #2061 OT_1B-
Point 2
Points 1 and 2 are the
Movable range prohibited range set with
Y axis stored stroke limit I.
Point 4
Movement prohibited range
II - 40
7.6 Stored Stroke Limit for Rotation Axis
7.6 Stored Stroke Limit for Rotation Axis
Stored stroke limits I and II are used as the stored stroke limit for the rotation axis. The area between the
maximum and minimum values of the prohibited range's parameters, which does not contain the 0 point of
the basic machine coordinate system, is the entry prohibited range.
The prohibited range parameters for the rotation axis can be set to establish "maximum value < minimum
value". This will be handled in the same manner as if "maximum value > minimum value".
(Example)
Stored stroke limit I (maximum value and minimum value of prohibited range parameter)
#2013 OT- : -70.000°
#2014 OT+ : 60.000°
Stored stroke limit II (maximum value and minimum value of prohibited range parameter)
#8204 Soft limit - : 30.000°
#8205 Soft limit + : 80.000°
80° Stored stroke limit

II entry prohibited
Stored stroke range
limit I entry
prohibited 30°
60°
range
0°
Movable range
-70° (290°)
(Note) Do not use stored stroke limits IB, IIB or IC. Invalidate stored stroke limits IB, IIB and IC by setting the
parameters as shown below.
#8210 OT INSIDE: 0 (stored stroke limit II valid, IIB invalid)
#2061, #2062 set to same value (stored stroke limits IB and IC invalid)
II - 41
7.7 Precautions
7.7 Precautions
(1) If the maximum value and minimum value of the stored stroke limit's prohibited range are set to the same
value, the following will occur.
• When the maximum value and minimum value are set to 0, if the outside is the prohibited range, the
entire range will be prohibited. If the inside is the prohibited range, the entire range will be the
moveable range.
• If data other than 0 is set for the maximum value and minimum value, the entire range will be the
moveable range.
(2) The stored stroke limit IC is valid when the axis parameter #2063 is changed.
If changed during automatic operation, the function will be validated after the smoothing for all axes
reaches 0.
(3) Make sure that the lower limit value of the stored stroke limit IC setting value is "smaller than the upper
limit value".
II - 42
III. MAINTENANCE
1. Daily Maintenance and Periodic Inspection and Maintenance
1.1 Maintenance Items

Maintenance is categorized into daily maintenance items (items to be carried at set intervals) and periodic
maintenance items (replacement of parts when life is reached).
Some parts will not function in a hardware manner when the life is reached, so these should be replaced
before the life is reached.
Class Name Life Inspection/replacement Remarks

Daily Escutcheon Once/two months
maintenance (Accordingly when dirty)
Periodic Battery Cumulative data When battery voltage drop Refer to
maintenance (lithium battery) holding time: caution alarm occurs "Control unit
45,000 hr (Guideline: approx. 5 years) battery" in
"1.2.1 Durable
Parts"
Cooling fan Control unit: Refer to left.
(700 Series only) 60,000 hr
Display unit:
50,000 hr
Back light 8.4-type: Refer to left.
700 Series: 30,000 hr
70 Series: 50,000 hr
10.4-type:
50,000 hr
Hard disk unit 20,000 hr or 5 years Refer to left.
(700 Series only) (Shorter one is applied.)
Other Operation board 106 punches Refer to left.
consumable
parts
1.1.1 Escutcheon
(1) Cleaning the escutcheon
(a) Prepare the rear side of the escutcheon to clean.
(b) Wipe the escutcheon with a soft, clean, dry cloth. If cleaning is still required, put some neutral
detergent on a cloth and wipe. Do not use alcohol, thinner, etc.
III - 1
1.1.2 LCD Panel

(1) Handling the LCD panel
(a) Precautions for use
• The polarizing plate (display surface) of the LCD panel surface can be easily scratched, so be
careful during handling.
• Glass is used in the LCD panel. Be careful not to drop the LCD panel or allow it to hit hard objects,
as the glass may chip or break.
• The polarizing plate may be stained or discolored if drops of water, etc., adhere to it for long
periods, so be sure to wipe off any moisture immediately.
• Wipe off any dirt, dust, etc., on the polarizing plate using absorbent cotton or other soft cloth.
• A CMOS LSI is used in the LCD panel, so be careful of static electricity when handling.
• Never disassemble the LCD panel. Doing so will damage the panel.
(b) Precautions for storage
• Do not store the LCD panel in locations having a high temperature or humidity. (Store within the
storage temperature range.)
• When storing the LCD panel as an individual unit, be sure that other objects do not touch or hit the
polarizing plate (display surface).
• When storing the LCD panel for long periods, be sure to store in a dark place away from exposure
to direct sunlight or fluorescent light.
(2) Other precautions for use

(a) Backlight life
The life of the backlight is as follows. (ambient temperature 25C°)
8.4-type : 30,000 hours (for 700 Series) or 50,000 hours (for 70 Series)
10.4-type : 50,000 hours
These are the time for luminance to drop to 50% of the initial value.
The backlight life is dependent on the temperature. The life tends to be shorter when used
continuously at lower temperatures.
(b) Luminance start
Due to the characteristics of the backlight, the luminance could drop slightly at lower temperatures. It
will take approx.10 to 15 minutes for the luminance to reach the rated value after the power is turned
ON.
(c) Unevenness, luminescent spots and irregularities
Uneven brightness, small luminescent spots or small dark spots may appear on LCD panel, but this
is not a fault.
(3) Replacing the backlight

Replacement should be commissioned to the Mitsubishi Service Center.
1.1.3 Compact Flash/IC card

(1) Handling the compact flash/IC card
The general handling methods for the compact flash/IC card are described below.
Refer to the instruction manual of the compact flash/IC card used for details.
(a) Precautions for use
• Insert the card in the correct direction.
• Do not touch the connector area with hands or metal.
• Do not apply excessive force to the connector area.
• Do not subject the card to bending or strong impacts.
• Do not open the cover or disassemble the card.
• Do not use the card in dusty locations.
(b) Precautions for storage
• Do not store the card in locations having a high temperature or humidity.
• Do not store the card in dusty locations.
III - 2
1.2 Replacement Methods [700 series]

1.2.1 Durable Parts
Control unit battery
All data, such as the parameters and machining programs that need to be backed up when the power is
turned OFF, are saved by a lithium battery installed in the control unit's battery holder.
Q6BAT BKO-C10811H03 (SANYO CR17335SE-R with

Battery
Mitsubishi specifications)
Battery cumulative data 45,000 hours (At room temperature. The life will be shorter if
holding time the temperature is high.)
Battery life Approx. 5 years (from date of battery manufacture)
(Note) Replace the battery when the alarm "Z52 Battery drop 0001" appears on the NC screen. The internal
data could be damaged if the alarm "Z52 Battery drop 0003" appears.
[Replacement procedures]
Always replace the battery with the control unit (machine) power turned OFF.
Complete the replacement within 30 minutes after turning the power OFF. (If the battery is not connected
within 30 minutes, the data being backed up may be destroyed.)
(1) Check that the machine power is turned OFF. (If the power is not OFF, turn it OFF.)
(2) Open the electric cabinet door, and confirm that the control unit LED, 7-segment display, etc., are all
OFF.
(3) Open the front cover of the control unit by pulling on the right side of the door.
(4) Pull the connector connected to the battery out from the BAT connector.
(5) Remove the battery from the battery holder.
(6) Fit the new battery into the battery holder.
(7) Insert the connector connected to the new battery into the BAT connector. Pay attention to the
connector orientation, being careful not to insert backwards.
(8) Close the front cover of the control unit. At this time, confirm that the cover is closed by listening for
the "click" sound when the latch catches.
(9) Close the door of the electric cabinet.
Front cover
BAT connector
Battery holder
Connector connected
to the battery
Battery
III - 3
[Precautions for handling battery]
(1) Always replace the battery with the same type.

(2) Do not disassemble the battery.
(3) Do not place the battery in flames or water.
(4) Do not pressurize and deform the battery.
(5) This is a primary battery so do not charge it.
(6) Dispose of the spent battery as industrial waste.
! CAUTION
If the battery low warning is issued, save the machining programs, tool data and parameters in an
input/output device, and then replace the battery. When the battery alarm is issued, the machining
programs, tool data and parameters may be destroyed. Reload the data after replacing the battery.
! Do not short circuit, charge, overheat, incinerate or disassemble the battery.
! Dispose the spent battery according to the local laws.
III - 4
Cooling fan for control unit
Type ........109P0412H731
Life ..........60,000 hours (When the rotary speed decreased 30% less than the initial values)
Life is a presumption value in 60°C environment, not guaranteed value.
Always replace the cooling fan with the control unit (machine) power turned OFF.
(2) Open the electric cabinet door.
(3) Remove the fan cover on the top center of the control unit. (Remove the fan cover by pushing up the
front tab.)
(4) Pull out the cooling fan from the control unit cooling fan housing.
(5) Pull the connector connected to the cooling fan out from the control unit PCB.
(6) Replace the cooling fan with the new one. Insert the connector connected to the new cooling fan into
the control unit PCB.
(7) Put the cooling fan into the control section cooling fan housing. (Be sure the label side is on the top.)
(8) Arrange the cooling fan wiring neatly in the control unit cooling fan housing.
(9) Install the fan cover. (First install the back tabs in the control unit. Then install the front tabs in the
control unit.)
(10) Check the cables and wires for leaks of connection, faulty connections, etc., then close the electric
cabinet door.
Front tab
Fan cover Cooling fan
Back
tab Control unit
! Caution
! Do not replace the control unit while the power is ON.
! Collect and dispose of the spent cooling fan according to the local laws.
III - 5
Cooling fan for display unit (XP terminal)
Type ........MMF-06D24DS-RP3
Life ..........50,000 hours (When the rotary speed decreased 20% less than the initial values)
Life is a presumption value in 60°C environment, not guarantee value.
Always replace the cooling fan for display unit with the control unit (machine) power turned OFF.
(2) Open the electric cabinet door.
(3) Remove the fan cover of cooling fan housing (2 parts) that is installed to PCB on back of display unit.
(Remove the fan cover by pushing up the front tab.)
(4) Pull out the cooling fan from the control unit cooling fan housing.
(5) Pull the connector connected to the cooling fan out from the control unit PCB.
(6) Replace the cooling fan with the new one. Insert the connector connected to the new cooling fan into
the control unit PCB.
(7) Put the cooling fan into the control section cooling fan housing. (Be sure the label side is on the top.)
(8) Arrange the cooling fan wiring neatly in the control unit cooling fan housing.
(9) Install the fan cover.
(10) Check the cables and wires for leaks of connection, faulty connections, etc., then close the electric
cabinet door.
Tab
Fan cover
Cooling fan
Cooling fan
housing
! Caution
! Do not replace the control unit while the power is ON.
! Collect and dispose of the spent cooling fan according to the local laws.
III - 6
1.2.2 Compact Flash
Control unit compact flash
Always replace the compact flash with the control unit (machine) power turned OFF.
(2) Open the electric cabinet door, and confirm that the control unit LED, 7-segment display, etc., are all
OFF.
(3) Open the front cover of the control unit.
(4) Press the eject lever twice to eject the compact flash.
(5) Insert the new compact flash. (The surface is faced on the observers' right.)
(7) Close the door of the electric cabinet.
Front
cover
Eject lever
Compact flash slot
Compact flash
(Note 1) There may be a compatibility problem between devices a commercially available compact flash
memory, so illegal operations may occur.
III - 7
1.2.3 IC Card
Front IC card
[Card insertion procedures]
(1) Open the card slot door on display unit right end.
(2) Insert the IC card. (The surface is faced on the observers' right.)
[Card replacement procedures]
(1) Open the card slot door on display unit right end.
(2) Press the eject lever twice to eject the IC card.
Eject lever
IC card
(Note 1) Do not eject an IC card during the data reading/writing.

(Note 2) There may be a compatibility problem between devices a commercially available IC card, so illegal
operations may occur.
III - 8

1.3.1 Durable Parts
Control unit battery
All data, such as the parameters and machining programs that need to be backed up when the power is
turned OFF, are saved by a lithium battery installed in the control unit's battery holder.
Battery Q6BAT BKO-C10811H03 (SANYO CR17335SE-R with

Mitsubishi specifications)
Battery cumulative data holding time 45,000 hours (At room temperature. The life will be shorter if
the temperature is high.))
Battery life Approx. 5 years (from date of battery manufacture)
(Note) Replace the battery when the alarm "Z52 Battery drop 0001" appears on the NC screen.
The internal data could be damaged if the alarm "Z52 Battery drop 0003" appears.
Always replace the battery with the control unit (machine) power turned OFF.
Complete the replacement within 30 minutes after turning the power OFF. (If the battery is not connected
within 30 minutes, the data being backed up might be destroyed.)
(2) Confirm that the control unit LED, 7-segment display, etc., are all OFF.
(3) Open the battery cover of the control unit. Pull the right side of the battery cover toward front.
(4) Pull the connector connected to the battery out from the BAT connector.
(5) Remove the battery from the battery holder.
(6) Fit the new battery into the battery holder.
(7) Insert the connector connected to the new battery into the BAT connector. Pay attention to the
connector orientation, being careful not to insert backwards.
Battery cover
Battery
Battery holder
BAT connector
III - 9
[Precautions for handling battery]

(1) Always replace the battery with the same type.
(2) Do not disassemble the battery.
(3) Do not place the battery in flames or water.
(4) Do not pressurize and deform the battery.
(5) This is a primary battery so do not charge it.
(6) Dispose of the spent battery as industrial waste.
! CAUTION
Do not short circuit, charge, overheat, incinerate or disassemble the battery.
Dispose the spent battery according to the local laws.
III - 10
1.3.2 Compact Flash
Front Compact Flash
[Card insertion procedures]

(1) Open the card slot door located on the display unit right end.
(2) Insert the compact flash. (The surface is faced on the observers' right.)
[Card ejecting procedures]

(1) Open the card slot door located on the display unit right end.
(2) Press the eject lever twice to eject the compact flash.
Compact flash
Eject lever
(Note 1) Do not eject a compact flash during the data reading/writing.

(Note 2) There may be a compatibility problem with non-recommended compact flashes, which may lead
illegal operations.
III - 11
IV. APPENDIXES
Appendix 1. List of Function Codes
Appendix 1. List of Function Codes
Function Subject Setting and Punch-out

code Control unit to parity Screen display unit Stored in output Internal NC system function
recognition V count display key-in memory
ISO ISO
0 to 9 Yes Counted Displayed Key-in Stored 0 to 9 Numerical data
A to Z Yes Counted Displayed Key-in Stored A to Z Addresses
+ Yes Counted Displayed Key-in Stored + Sign, variable operator (+)
- Yes Counted Displayed Key-in Stored - Sign, variable operator (-)
. Yes Counted Displayed Key-in Stored . Decimal point
, Yes Counted Displayed Key-in Stored ,
Block delete (optional block skip)
/ Yes Counted Displayed Key-in Stored /
Variable operator (÷)
No key-in
Displayed End of record (tape storage end)
% Yes Counted (automatically Stored %
(%) Rewind start & stop during tape search
inserted)
Displayed Key-in
LF/NL Yes Counted Stored LF End of block
(;) ;/EOB
( Yes Counted Displayed Key-in Stored ( Control out (comment start)
) Yes Counted Displayed Key-in Stored ) Control in (comment end)
: Yes Counted Displayed No key-in Stored : Program number address (instead of O.)
# Yes Counted Displayed Key-in Stored # Variable number
∗ Yes Counted Displayed Key-in Stored ∗ Variable operator (X)
= Yes Counted Displayed Key-in Stored = Variable definition
[ Yes Counted Displayed Key-in Stored [ Variable operator
] Yes Counted Displayed Key-in Stored ] Variable operator
Not
BS No No key-in Stored
displayed
Not
HT No No key-in Stored
displayed
SP
Not (T-V
SP No Key-in Stored
displayed automatic
adjustment)
Not
CR No No key-in Stored
displayed
Not Not Not
DEL No No key-in
counted displayed stored
Not Not Not
NULL No No key-in
counted displayed stored
Any other No Counted (Note 2) No key-in Stored
(Note 1) Codes not listed in the above table are stored on tape, but an error will result during operation if they
are not comments.
(Note 2) This denotes characters (including blanks) which are stored inside and which correspond to the
command codes. "@" is not displayed.
IV - 1
Appendix 2. Table of Command Value Ranges
<Table of command values and setting value ranges>
(1) Linear axis: Input increment [mm] (M system)

Least command
0.001 0.0001 0.00001 0.000001
increment
Maximum stroke ±99999.999 mm ±99999.9999 mm ±99999.99999 mm ±99999.999999 mm
(value for machine
coordinate system)
Maximum ±99999.999 mm ±99999.9999 mm ±99999.99999 mm ±99999.999999 mm
programmable
dimension
Rapid traverse rate 1 to 1000000 mm/min 1 to 1000000 mm/min 1 to 1000000 mm/min 1 to 1000000 mm/min
(including dry run)
Cutting feed rate 0.001 to 1000000.000 0.0001 to 0.00001 to 0.000001 to
(including dry run) mm/min 1000000.0000 1000000.00000 1000000.000000
Asynchronous feed mm/min mm/min mm/min
(feed per minute)
Synchronous feed 0.001 to 999.999 0.0001 to 999.9999 0.00001 to 999.99999 0.000001 to
(feed per revolution) mm/rev mm/rev mm/rev 999.999999 mm/rev
2nd to 4th reference ±99999.999 mm ±99999.9999 mm ±99999.99999 mm ±99999.999999 mm
position compensation
(value for machine
coordinate system)
Tool compensation ±99999.999 mm ±99999.9999 mm ±99999.99999 mm ±99999.999999 mm
amount
(shape)
amount
(wear)
Incremental feed 0.001 mm/pulse 0.0001 mm/pulse 0.00001 mm/pulse 0.000001 mm/pulse
amount
Handle feed amount 0.001 mm/pulse 0.0001 mm/pulse 0.00001 mm/pulse 0.000001 mm/pulse
Soft limit range ±99999.999 mm ±99999.9999 mm ±99999.99999 mm ±99999.999999 mm
(value with machine
coordinate system)
Dwell time 0 to 99999.999 s 0 to 99999.9999 s 0 to 99999.99999 s 0 to 99999.999999 s
Backlash compensation ±9999999 pulse ±9999999 pulse ±9999999 pulse ±9999999 pulse
amount
Pitch error -32768 to 32767 pulse -32768 to 32767 pulse -32768 to 32767 pulse -32768 to 32767 pulse
compensation amount
Thread lead (F) 0.001 to 999.999 0.0001 to 999.9999 0.00001 to 999.99999 0.000001 to
mm/rev mm/rev mm/rev 999.999999 mm/rev
Thread lead 0.00001 to 999.99999 0.000001 to 0.0000001 to 0.00000001 to
(precision E) mm/rev 999.999999 mm/rev 999.9999999 mm/rev 999.99999999 mm/rev
Thread lead 0.03 to 999.99 0.026 to 999.999 0.0255 to 999.9999 0.02541 to 999.99999
(ridges/inch)
IV - 2
(2) Linear axis: Input increment [inch] (M system)

Least command
0.0001 0.00001 0.000001 0.0000001
increment
Maximum stroke ±9999.9999 inch ±9999.99999 inch ±9999.999999 inch ±9999.9999999 inch
(value for machine
coordinate system)
Maximum ±9999.9999 inch ±9999.99999 inch ±9999.999999 inch ±9999.9999999 inch
programmable
dimension
Rapid traverse rate 1 to 100000 inch/min 1 to 100000 inch/min 1 to 100000 inch/min 1 to 100000 inch/min
(including dry run)
Cutting feed rate 0.0001 to 0.00001 to 0.000001 to 0.0000001 to
(including dry run) 100000.0000 inch/min 100000.00000 100000.000000 100000.0000000
Asynchronous feed inch/min inch/min inch/min
(feed per minute)
Synchronous feed 0.0001 to 999.9999 0.00001 to 999.99999 0.000001 to 0.0000001 to
(feed per revolution) inch/rev inch/rev 999.999999 inch/rev 999.9999999 inch/rev
2nd to 4th reference ±9999.9999 inch ±9999.99999 inch ±9999.999999 inch ±9999.9999999 inch
(value for machine
coordinate system)
Tool compensation ±9999.9999 inch ±9999.99999 inch ±9999.999999 inch ±9999.9999999 inch
amount
(shape)
amount
(wear)
Incremental feed 0.0001 inch/pulse 0.00001 inch/pulse 0.000001 inch/pulse 0.0000001 inch/pulse
amount
Handle feed amount 0.0001 inch/pulse 0.00001 inch/pulse 0.000001 inch/pulse 0.0000001 inch/pulse
Soft limit range ±9999.9999 inch ±9999.99999 inch ±9999.999999 inch ±9999.9999999 inch
(value with machine
coordinate system)
amount
compensation amount
Thread lead (F) 0.0001 to 99.9999 0.00001 to 99.99999 0.000001 to 0.0000001 to
inch/rev inch/rev 99.999999 inch/rev 99.9999999 inch/rev
Thread lead 0.000001 to 0.0000001 to 0.00000001 to 0.000000001 to
(precision E) 39.370078 inch/rev 39.3700787 inch/rev 39.37007874 inch/rev 39.370078740
inch/rev
(ridges/inch) 9999.99999 9999.999999 9999.9999999
IV - 3
(3) Rotation axis: degree [°] (M system)

Least command
0.001 0.0001 0.00001 0.000001
increment
Maximum stroke ±99999.999 ° ±99999.9999 ° ±99999.99999 ° ±99999.999999 °
(value for machine
coordinate system)
Maximum ±99999.999 ° ±99999.9999 ° ±99999.99999 ° ±99999.999999 °
programmable
dimension
Rapid traverse rate 1 to 1000000 °/min 1 to 1000000 °/min 1 to 1000000 °/min 1 to 1000000 °/min
(including dry run)
(including dry run) 1000000.000 °/min 1000000.0000 °/min 1000000.00000 °/min 1000000.000000
Asynchronous feed °/min
(feed per minute)
Synchronous feed 0.001 to 999.999 °/rev 0.0001 to 0.00001 to 0.000001 to
(feed per revolution) 999.9999 °/rev 999.99999 °/rev 999.999999 °/rev
2nd to 4th reference ±99999.999 ° ±99999.9999 ° ±99999.99999 ° ±99999.999999 °
(value with machine
coordinate system)
Incremental feed 0.001 °/pulse 0.0001 °/pulse 0.00001 °/pulse 0.000001 °/pulse
amount
Handle feed amount 0.001 °/pulse 0.0001 °/pulse 0.00001 °/pulse 0.000001 °/pulse
Soft limit range ±99999.999 ° ±99999.9999 ° ±99999.99999 ° ±99999.999999 °
(value with machine
coordinate system)
amount
compensation amount
IV - 4
<Table of command values and setting value ranges>
(1) Linear axis: Input increment [mm] (L system)

Least command
0.001 0.0001 0.00001 0.000001
increment
Maximum stroke ±99999.999 mm ±99999.9999 mm ±99999.99999 mm ±99999.999999 mm
(value for machine
coordinate system)
Maximum ±99999.999 mm ±99999.9999 mm ±99999.99999 mm ±99999.999999 mm
programmable
dimension
Rapid traverse rate 1 to 1000000 mm/min 1 to 1000000 mm/min 1 to 1000000 mm/min 1 to 1000000 mm/min
(including dry run)
Cutting feed rate 0.001 to 1000000.000 0.0001 to 0.00001 to 0.000001 to
(including dry run) mm/min 1000000.0000 1000000.00000 1000000.000000
Asynchronous feed mm/min mm/min mm/min
(feed per minute)
Synchronous feed 0.0001 to 999.9999 0.00001 to 999.99999 0.000001 to 0.0000001 to
(feed per revolution) mm/rev mm/rev 999.999999 mm/rev 999.9999999 mm/rev
2nd to 4th reference ±99999.999 mm ±99999.9999 mm ±99999.99999 mm ±99999.999999 mm
(value for machine
coordinate system)
amount
(shape)
amount
(wear)
Incremental feed 0.001 mm/pulse 0.0001 mm/pulse 0.00001 mm/pulse 0.000001 mm/pulse
amount
Handle feed amount 0.001 mm/pulse 0.0001 mm/pulse 0.00001 mm/pulse 0.000001 mm/pulse
Soft limit range ±99999.999 mm ±99999.9999 mm ±99999.99999 mm ±99999.999999 mm
(value with machine
coordinate system)
amount
compensation amount
Thread lead (F) 0.001 to 999.999 0.0001 to 999.9999 0.00001 to 999.99999 0.000001 to
mm/rev mm/rev mm/rev 999.999999 mm/rev
(precision E) mm/rev 999.999999 mm/rev 999.9999999 mm/rev 999.99999999
mm/rev
Thread lead 0.03 to 9999.99 0.026 to 9999.999 0.0255 to 9999.9999 0.02541 to
(ridges/inch) 9999.99999
IV - 5
(2) Linear axis: Input increment [inch] (L system)

Least command
0.0001 0.00001 0.000001 0.0000001
increment
Maximum stroke ±9999.9999 inch ±9999.99999 inch ±9999.999999 inch ±9999.9999999 inch
(value for machine
coordinate system)
Maximum ±9999.9999 inch ±9999.99999 inch ±9999.999999 inch ±9999.9999999 inch
programmable
dimension
Rapid traverse rate 1 to 100000 inch/min 1 to 100000 inch/min 1 to 100000 inch/min 1 to 100000 inch/min
(including dry run)
(including dry run) 100000.0000 inch/min 100000.00000 100000.000000 100000.0000000
Asynchronous feed inch/min inch/min inch/min
(feed per minute)
Synchronous feed 0.000001 to 0.0000001 to 0.00000001 to 0.000000001 to
(feed per revolution) 99.999999 inch/rev 99.9999999 inch/rev 99.99999999 inch/rev 99.999999999
inch/rev
2nd to 4th reference ±9999.9999 inch ±9999.99999 inch ±9999.999999 inch ±9999.9999999 inch
(value for machine
coordinate system)
amount
(shape)
amount
(wear)
Incremental feed 0.0001 inch/pulse 0.00001 inch/pulse 0.000001 inch/pulse 0.0000001 inch/pulse
amount
Handle feed amount 0.0001 inch/pulse 0.00001 inch/pulse 0.000001 inch/pulse 0.0000001 inch/pulse
Soft limit range ±9999.9999 inch ±9999.99999 inch ±9999.999999 inch ±9999.9999999 inch
(value with machine
coordinate system)
amount
compensation amount
Thread lead (F) 0.0001 to 99.9999 0.00001 to 99.99999 0.000001 to 0.0000001 to
inch/rev inch/rev 99.999999 inch/rev 99.9999999 inch/rev
Thread lead 0.000001 to 0.0000001 to 0.00000001 to 0.000000001 to
(precision E) 39.370078 inch/rev 39.3700787 inch/rev 39.37007874 inch/rev 39.370078740
inch/rev
(ridges/inch) 9999.99999 9999.999999 9999.9999999
IV - 6
(3) Rotation axis: degree [°] (L system)

Least command
0.001 0.0001 0.00001 0.000001
increment
Maximum stroke ±99999.999 ° ±99999.9999 ° ±99999.99999 ° ±99999.999999 °
(value for machine
coordinate system)
Maximum ±99999.999 ° ±99999.9999 ° ±99999.99999 ° ±99999.999999 °
programmable
dimension
Rapid traverse rate 1 to 1000000 °/min 1 to 1000000 °/min 1 to 1000000 °/min 1 to 1000000 °/min
(including dry run)
(including dry run) 1000000.000 °/min 1000000.0000 °/min 1000000.00000 °/min 1000000.000000
Asynchronous feed °/min
(feed per minute)
Synchronous feed 0.0001 to 0.00001 to 0.000001 to 0.0000001 to
(feed per revolution) 999.9999 °/rev 999.99999 °/rev 999.999999 °/rev 999.9999999 °/rev
2nd to 4th reference ±99999.999 ° ±99999.9999 ° ±99999.99999 ° ±99999.999999 °
(value with machine
coordinate system)
Incremental feed 0.001 °/pulse 0.0001 °/pulse 0.00001 °/pulse 0.000001 °/pulse
amount
Handle feed amount 0.001 °/pulse 0.0001 °/pulse 0.00001 °/pulse 0.000001 °/pulse
Soft limit range ±99999.999 ° ±99999.9999 ° ±99999.99999 ° ±99999.999999 °
(value with machine
coordinate system)
amount
compensation amount
IV - 7
Appendix 3. Circular Cutting Radius Error
Appendix 3. Circular Cutting Radius Error

When circular cutting is performed, an error is caused between the command coordinate and the tracking
coordinate due to the tracking delay in the smoothing circuit and servo system, and the workpiece ends up
with a radius smaller than the commanded value. The method for obtaining this error (radius error) is shown
below.
F
A
F A : Command coordinate
B : Tracking coordinate
B
R : Command radius (mm)
ΔR : Radius error (mm)
Δθ : Angle error (rad)
Δθ
F : Cutting feed rate (m/min)
ΔR
The radius error ΔR and angle error Δθ are calculated from the following formula.
Exponential 1 1 2
1 2
F × 103 2
acceleration/ deceleration ΔR = R • ( 2 Ts + 2 Tp ) • ( 60 ) (mm)
Linear 1 1 1 F × 103 2
acceleration/ deceleration ΔR = R • ( 24 Ts2 + 2 Tp2) • ( 60 ) (mm)
F F
Δθ= tan-1 (Ts • -1
R ) + tan (Tp • R ) (rad)
Ts: Time constant (s) of specified smoothing circuit
Tp: Position loop time constant
(Note 1) When the ΔR radius error applying with circular cutting does not come within the allowable value,
proceed to reduce the cutting feed rate F, set Ts to a lower value or review the program.
(Note 2) In the steady state, ΔR is constant. However, it is not constant with command start and stop
transitions. Under command start and stop conditions, therefore, the tracking coordinate should be
as shown in the figure below.
Start/stop
ΔR
ΔR
Command Tracking
IV - 8
Appendix 4. Registering/Editing the Fixed Cycle Program
4.1 Fixed Cycle Operation Parameters

The subprogram for the fixed cycle can be input, output and edited.
! CAUTION
Do not change the fixed cycle program without prior approval from the machine maker.
4.1 Fixed Cycle Operation Parameters

To input/output or edit the data of each fixed cycle subprogram, use the Data I/O and Edit screens in the
same way as when creating usual user-created work programs. In this case, the parameters must have been
set. Set "1" in parameter "#1166 fixpro". If this parameter is valid, the IN/OUT and Edit screens are usable
only for operating a fixed cycle control subprogram. During this period, program file displays only fixed cycle
programs. Thus, after fixed cycle program operation, return parameter to "0".
(Note) Parameter "#1166 fixpro" will be set to 0 when the power is turned OFF.
4.2 Transmitting/Erasing the Fixed Cycle Program

Transmit/erase the fixed cycle program from the Data I/O screen. Check that fixed cycle operation parameter
"#1166 fixpro" is valid.
The operating procedure is the same as a user machining program.
IV - 9
4.3 Standard Fixed Cycle Subprogram (For L system)
Automatic tool length

G37 (O370)
measurement
G31 Z #5 F #3 ;
1F [ROUND [ ABS [#2 - [ ##10 ∗ #11 − #12 ] ] ] GT #8 ] GOTO 1 ;
1F [ROUND [ ##10 ∗ #11 - #12 ] EQ #4 ] GOTO 1 ;
##9 = #10 - #12/#11 - #2/#11 + ##9 ;
#3003 = #1 ;
N2 ;
M99 ;
N1 # 3901 = 126 ;
G74 (O740) End face cutoff cycle
G. 1 ;
1F [ ABS [ #2 ] GT 0 ] GOTO 10 ;
#14 = 1 ;
N10 #13 = #3 ;
IF [ #15 NE 0 ] GOTO 11 ;
#13 = #3 - #5 ;
N11 #16 = 0 ;
D0 1 ;
#10 = 0 ;
#11 = #4 ;
D0 2 ;
#10 = #10 + #4 ;
IF [ ABS [ #10 ] GE [ABS [ #1 ] ] ] GOTO 1 ;
G01 X #11 ;
G00 X #6 ;
#11 = #4 - #6 ;
END 2 ;
N1 G01 X#1 − #10 + #11 ;
IF [ #15 EQ 0 ] GOTO 20 ;
IF [ #16 EQ 0 ] GOTO 21 ;
N20 G00 Y#5 ;
N21 #16 = 1 ;
G00X - #1 ;
IF [ #14 ] GOTO 3 ;
#12 = #12 + #3 ;
IF [ ABS [ #12 ] LT [ABS [ #2 ] ] ] GOTO 2 ;
#14 = 1 ;
#13 = #2 - #12 + #13 ;
N2 G00 Y #13 ;
#13 = #3 - #5 ;
END 1 ;
N3 G00 Y - #2 - #5 ;
M99 ;
IV - 10
G75 (O750) Longitudinal cutting cycle
G. 1 ;
1F [ ABS [ #1 ] GT 0 ] GOTO 10 ;
#14 = 1 ;
N10 #13 = #4 ;
IF [ #15 NE 0 ] GOTO 11 ;
#13 = #4 - #5 ;
N11 #16 = 0 ;
D0 1 ;
#10 = 0 ;
#11 = #3 ;
D0 2 ;
#10 = #10 + #3 ;
IF [ ABS [ #10 ] GE [ABS [ #2 ] ] ] GOTO 1 ;
G01 Y #11 ;
G00 Y #6 ;
#11 = #3 - #6 ;
END 2 ;
N1 G01 Y#2 - #10 + #11 ;
IF [ #15 EQ 0 ] GOTO 20 ;
IF [ #16 EQ 0 ] GOTO 21 ;
N20 G00 X#5 ;
N21 #16 = 1 ;
G00Y - #2 ;
IF [ #14 ] GOTO 3 ;
#12 = #12 + #4 ;
IF [ ABS [ #12 ] LT [ABS [ #1 ] ] ] GOTO 2 ;
#14 = 1 ;
#13 = #1 - #12 + #13 ;
N2 G00 X #13 ;
#13 = #4 - #5 ;
END 1 ;
N3 G00 X - #1 - #5 ;
M99 ;
IV - 11
G75.1 (O751) Groove cutting cycle
G. 1 ;
#3003 = #8 OR 1 ;
G0 X #1 ;
G1 Y #2 ;
G0 Y − #2 ;
X #5 ;
1F [ #3 EQ 0 ] GOTO 1 ;
G1 X - #3 Y #4 ;
N1 G1 Y#6 ;
X - #7 ;
G0Y - #2 ;
X - #5 ;
1F [ #3 EQ 0 ] GOTO 2 ;
G1 X #3 Y #4 ;
N2 G1 Y#6 ;
X #7 ;
#3003 = #8 ;
G0Y - #2 ;
M99 ;
Compound thread cutting

G76 (O760)
cycle
G. 1 ;
#12 = 1 ;
#13 = #9 ;
1F [ ABS [ #13 ] GE [ ABS [ #8 ] ] ] GOTO 1 ;
#16 = 1 ;
#13 = #8 ;
N1 #11 = #13 ;
1F [ ABS [ #11 ] LT [ ABS [ #4 − #5 ] ] ] GOTO 2 ;
#11 = #4 - #5 ;
#14 = 1 ;
N2 #17 = #11 ;
#18 = ROUND [ [ #4 - #11 - #5 ] ∗ #7 ] ;
IF [ [ #18 XOR #1 ] GE 0 ] GOTO 10 ;
#18 = - #18 ;
N10 #19 = #18 ;
#10 = ROUND [ [ #11 + #5 ] ∗ #7 ] ;
IF [ [ #10 XOR #1 ] GE 0 ] GOTO 20 ;
#10 = - #10 ;
N20 G00 X#10 ;
#20 = #10
D0 1 ;
#15 = ROUND [ #10 ∗ #3/#1 ] ;
G00 Y #2 + #3 - #4 - #15 + #11 ;
G33 X#1 - #10 - #18 Y -#3 + #15 ;
G00 Y - #2 + #4 − #11 ;
IF [ #14 GT 0 ] GOTO 3 ;
IF [ #16 GT 0 ] GOTO 7 ;
#12 = #12 + 1 ;
#13 = ROUND [ #9 ∗ SQRT [ #12 ] ] ;
IV - 12
IF [ ABS [ #13 − #11 ] GE [ ABS [ #8 ] ] ] GOTO 8 ;

#16 = 1 ;
N7 #13 = #11 + #8 ;
N8 #11 = #13 ;
IF [ ABS [ #11 ] LT [ ABS [ #4 − #5 ] ] ] GOTO 9 ;
#11 = #4 - #5 ;
#14 = 1 ;
N9 #10 = ROUND [ [ #17 - #11 ] ∗ #7 ] ;
IF [ [ #10XOR#1] GE 0 ] GOTO 6 ;
#10 = -#10 ;
N6 #10 = #10 + #20 ;
G00 X - #1 + #10 + #18 ;
IF [ #14 LT 0 ] GOTO 11 ;
#18 = 0 ;
GOTO 12 ;
N11 #18 = #19 - #10 + #20 ;
N12 END 1 ;
N3 IF [ ABS [ #6 ] LT 1 ] GOTO 5 ;
#14 = 0 ;
#13 = 0 ;
D0 2 ;
IF [ #14 GT 0 ] GOTO 5 ;
#13 = #13 + #6 ;
IF [ ABS [ #13 ] LT [ ABS [ #5 ] ] ] GOTO 4 ;
#13 = #5 ;
#14 = 1 ;
N4 G00 X #10 − #1 ;
G00 Y #2 + #3 - #4 + #13 − #15 + #11 ;
G33 X #1 - #10 Y - #3 + #15 ;
G00 Y - #2 + #4 - #13 - #11 ;
END 2 ;
N5 G00 X - #1 ;
M99 ;
2-part system simultaneous

G76.1 (O761)
compound thread cutting cycle
G. 1 ;
N761 !L10
#12 = 1 ;
#13 = #9 ;
1F [ ABS [ #13 ] GE [ ABS [ #8 ] ] ] GOTO 1 ;
#16 = 1 ;
#13 = #8 ;
N1 #11 = #13 ;
1F [ ABS [ #11 ] LT [ ABS [ #4 − #5 ] ] ] GOTO 2 ;
#11 = #4 - #5 ;
#14 = 1 ;
N2 #17 = #11 ;
#18 = ROUND [ [ #4 - #11 - #5 ] ∗ #7 ] ;
IF [ [ #18 XOR #1 ] GE 0 ] GOTO 10 ;
#18 = - #18 ;
N10 #19 = #18 ;
#10 = ROUND [ [ #11 + #5 ] ∗ #7 ] ;
IV - 13
IF [ [ #10 XOR #1 ] GE 0 ] GOTO 20 ;

#10 = - #10 ;
N20 G00 X#10 ;
#20 = #10
D0 1 ;
#15 = ROUND [ #10 ∗ #3/#1 ] ;
G00 Y #2 + #3 - #4 - #15 + #11 ;
!L11 ;
G33 X#1 - #10 - #18 Y -#3 + #15 ;
G00 Y - #2 + #4 - #11 ;
!L12 ;
IF [ #14 GT 0 ] GOTO 3 ;
IF [ #16 GT 0 ] GOTO 7 ;
#12 = #12 + 1 ;
#13 = ROUND [ #9 ∗ SQRT [ #12 ] ] ;
IF [ ABS [ #13 - #11 ] GE [ ABS [ #8 ] ] ] GOTO 8 ;
#16 = 1 ;
N7 #13 = #11 + #8 ;
N8 #11 = #13 ;
IF [ ABS [ #11 ] LT [ ABS [ #4 − #5 ] ] ] GOTO 9 ;
#11 = #4 - #5 ;
#14 = 1 ;
N9 #10 = ROUND [ [ #17 - #11 ] ∗ #7 ] ;
IF [ [ #10XOR#1] GE 0 ] GOTO 6 ;
#10 = -#10 ;
N6 #10 = #10 + #20 ;
G00 X - #1 + #10 + #18 ;
IF [ #14 LT 0 ] GOTO 11 ;
#18 = 0 ;
GOTO 12 ;
N11 #18 = #19 - #10 + #20 ;
N12 END 1 ;
N3 IF [ ABS [ #6 ] LT 1 ] GOTO 5 ;
#14 = 0 ;
#13 = 0 ;
D0 2 ;
IF [ #14 GOTO ] GOTO 5 ;
#13 = #13 + #6 ;
IF [ ABS [ #13 ] LT [ ABS [ #5 ] ] ] GOTO 4 ;
#13 = #5 ;
#14 = 1 ;
N4 G00 X #10 - #1 ;
G00 Y #2 + #3 − #4 + #13 - #15 + #11 ;
!L11 ;
G33 X #1 - #10 Y - #3 + #15 ;
G00 Y - #2 + #4 - #13 - #11 ;
!L12 ;
END 2 ;
N5 G00 X - #1 ;
M99 ;
IV - 14
2-system simultaneous
G76.2 (O762)
compound thread cutting cycle
G. 1 ;
N762 !L10 ;
#12 = 1 ;
#13 = #9 ;
1F [ ABS [ #13 ] GE [ ABS [ #8 ] ] ] GOTO 1 ;
#16 = 1 ;
#13 = #8 ;
N1 #11 = #13 ;
1F [ ABS [ #11 ] LT [ ABS [ #4 - #5 ] ] ] GOTO 2 ;
#11 = #4 - #5 ;
#14 = 1 ;
N2 #17 = #11 ;
#18 = ROUND [ [ #4 - #11 - #5 ] ∗ #7 ] ;
IF [ [ #18 XOR #1 ] GE 0 ] GOTO 10 ;
#18 = - #18 ;
N10 #19 = #18 ;
#10 = ROUND [ [ #11 + #5 ] ∗ #7 ] ;
IF [ [ #10 XOR #1 ] GE 0 ] GOTO 20 ;
#10 = - #10 ;
N20 IF [# 27 NE 1 ] GOTO 21 ;
G00 X#10 ;
N21 #20 = #10 ;
#28 = 1 ;
D01 ;
#15 = ROUND [ #10 ∗ #3/#1 ] ;
#29 = #28 MOD 2 ;
IF [ [ #27 EQ 1 ] AND [#29 EQ 0 ] GOTO 22 ;
IF [ [ #27 EQ 2 ] AND [#29 EQ 1 ] GOTO 22 ;
G00 Y #2 + #3 - #4 - #15 + #11 ;
!L11 ;
G33 X#1 - #10 - #18 Y -#3 + #15 ;
G00 Y - #2 + #4 - #11 ;
#21 = #18 ;
!L12 ;
N22 IF [ #14 GT 0 ] GOTO 3 ;
IF [ #16 GT 0 ] GOTO 7 ;
#12 = #12 + 1 ;
#13 = ROUND [ #9 ∗ SQRT [ #12 ] ] ;
IF [ ABS [ #13 - #11 ] GE [ ABS [ #8 ] ] ] GOTO 8 ;
#16 = 1 ;
N7 #13 = #11 + #8 ;
N8 #11 = #13 ;
IF [ ABS [ #11 ] LT [ ABS [ #4 - #5 ] ] ] GOTO 9 ;
#11 = #4 - #5 ;
#14 = 1 ;
N9 #10 = ROUND [ [ #17 - #11 ] ∗ #7 ] ;
IF [ [ #10XOR#1] GE 0 ] GOTO 6 ;
#10 = -#10 ;
N6 #10 = #10 + #20 ;
IF [ [ #27 EQ 1 ] AND [#29 EQ 1 ] GOTO 24 ;
IF [ [ #27 EQ 2 ] AND [#29 EQ 0 ] GOTO 24 ;
IF [ [ #27 EQ 2 ] AND [#28 EQ 1 ] GOTO 23 ;
G00 X − #1 + #10 + #21 ;
IV - 15
GOTO 24 ;
N23 G00 X#10 ;
N24 IF [ #14 LT 0 ] GOTO 11 ;
#18 = 0 ;
GOTO 12 ;
N11 #18 = #19 - #10 + #20 ;
N12 #28 = #28 + 1 ;
END 1 ;
N3 IF [ ABS [ #6 ] LT 1 ] GOTO 5 ;
#14 = 0 ;
#13 = 0 ;
D0 2 ;
IF [ #14 GT 0 ] GOTO 5 ;
#13 = #13 + #6 ;
IF [ ABS [ #13 ] LT [ ABS [ #5 ] ] ] GOTO 4 ;
#13 = #5 ;
#14 = 1 ;
N4 #29 = #28 MOD 2 ;
IF [ [ #27 EQ 1 ] AND [#29 EQ 1 ] GOTO 25 ;
IF [ [ #27 EQ 2 ] AND [#29 EQ 0 ] GOTO 25 ;
G00 X #10 - #1 + #21 ;
#21 = 0 ;
G00 Y #2 + #3 − #4 + #13 - #15 + #11 ;
!L11 ;
G33 X #1 - #10 Y − #3 + #15 ;
G00 Y - #2 + #4 - #13 - #11 ;
!L12 ;
N25 #28 = #28 + 1 ;
END 2 ;
N5 G00 X - #1 ;
M99 ;
%
G77 (O770) Longitudinal cutting cycle
G. 1 ;
1F [ [ #1 EQ 0 ] OR [ #2 EQ 0 ] ] GOTO 1 ;
Y #2 + #7 ;
G1 X #1 Y - #7 ;
Y - #2 ;
G0 X - #1 ;
N1 M99 ;
G78 (O780) Thread cutting cycle
G. 1 ;
1F [ [ #1 EQ 0 ] OR [ #2 EQ 0 ] ] GOTO 1 ;
Y #2 + #7 ;
G33 X #1 Y - #7 F #9 E #10 ;
G0 Y - #2 ;
X - #1 ;
N1 M99 ;
IV - 16
G79 (O790) End face cutoff cycle
G. 1 ;
1F [ [ #1 EQ 0 ] OR [ #2 EQ 0 ] ] GOTO 1 ;
X #1 + #7 ;
G1 X - #7 Y #2 ;
X - #1 ;
G0 Y - #2 ;
N1 M99 ;
G83
(O830) Deep hole drilling cycle B
G87
G. 1 ;
1F [ #30 ] GOTO 2 ;
M #24 ;
#29 = #11 #28 = 0 ;
Z #2 ;
#2 = ##5 #3003 = #8 OR 1 ;
D0 1 ;
#28 = #28 − #11 #26 = - #28 - #29 ;
Z #26 ;
IF [ ABS [ #28 ] GE [ ABS [ #3 ] ] ] GOTO 1 ;
G1 Z #29 ;
G0 Z #28 ;
G29 = #11 + #14 ;
END 1 ;
N1 G1 Z #3 - #26 ;
G4 P #4 ;
#3003 = #8 ;
G0Z - #3 - #2 ;
IF [#24 EQ #0 ] GOTO 2 ;
M #24 + 1 ;
G4 P #21 ;
N2 M99 ;
IV - 17
G83
(O831) Deep hole drilling cycle A
G87
G. 1 ;
1F [ #30 ] GOTO 2 ;
M #24 ;
#29 = #0 #28 = #11 ;
Z #2 ;
#2 = ##5 #3003 = #8 OR 1 ;
D0 1 ;
#29 = #29 + #11 ;
IF [ ABS [ #29 ] GE [ ABS [ #3 ] ] ] GOTO 1 ;
G1 Z #28 ;
G0 Z - #14 ;
#28 = #11 + #14 ;
END 1 ;
N1 G1 Z #3 - #29 + #28 ;
G4 P #4 ;
#3003 = #8 ;
G0Z - #3 - #2 ;
IF [#24 EQ #0 ] GOTO 2 ;
M #24 + 1 ;
G4 P #21 ;
N2 M99 ;
G83.2 (O832) Deep hole drilling cycle 2
G. 1 ;
1F [ #30 ] GOTO 3 ;
#3003 = #8 OR 1 ;
#29 = #12 #28 = 0 ;
G0 Z #2 ;
IF [ #12 NE #0 ] GOTO 1 ;
IF [ #11 EQ #0 ] GOTO 2 ;
N1 #28 = #28 - #12 #26 = - #28 - #29 ;
IF [ ABS [ #28 ] GE [ ABS [ #3 ] ] ] GOTO 2 ;
G1 Z #12 ;
G4 P #4 ;
G0 Z #28 - #2 ;
G4P # 13 ;
G29 = #11 + #15 ;
D0 1 ;
#28 = #28 - #11 #26 = - #28 - #29 ;
G0 Z #26 + #2 ;
IF [ ABS [ #28 ] GE [ ABS [ #3 ] ] ] GOTO 2 ;
G1 Z #29 ;
G4 P #4 ;
G0 Z #28 - #2 ;
G4 P # 13 ;
END 1 ;
N2 G1 Z #3 - #26 ;
G4 P #4 ;
#3003 = #8 ;
G0Z - #3 - #2 ;
N3 M99 ;
IV - 18
G84
(O840) Tap cycle
G88
G. 1 ;
1F [ #30 ] GOTO 2 ;
M #24 ;
Z #2 ;
#2 = ##5 #3003 = #8 OR 1 #3004 = #9 OR 3 ;
G1 Z #3 ;
G4 P #4 ;
M4 ;
#3900 = 1 ;
G1 Z - #3 ;
#3004 = #9 ;
M3 ;
#3003 = #8 ;
IF [#24 EQ #0 ] GOTO 1 ;
M #24 + 1 ;
G4 P #21 ;
N1 G0 Z − #2 ;
N2 M99 ;
G85
(O850) Boring cycle
G89
G. 1 ;
1F [ #30 ] GOTO 2 ;
M #24 ;
Z #2 ;
#2 = ##5 #3003 = #8 OR 1 ;
G1 Z #3 ;
G4 P #4 ;
#3003 = #8 ;
Z - #3 F #23 ;
F #22 ;
IF [#24 EQ #0 ] GOTO 1 ;
M #24 + 1 ;
G4 P #21 ;
N1 G0 Z − #2 ;
N2 M99 ;
IV - 19
4.4 Standard Fixed Cycle Subprogram (For M system)
G81 (O810) Drill, spot drill
Fixed cycle block 1 movement command

G. 1 ;
Check for fixed cycle invalidity.
1F [#30] GOTO1 ;
Z#2 G#6 H#7 ;
#2 = ##5
Inhibit single block stop.
#3003 = #8 OR 1 ;
G1 Z#3 ;
#3003 = #8 ;
Return.
G0 Z - #3 - #2 ;
N1 M99%
G82 (O820) Drill, counter boring

G. 1 ;
1F [#30] GOTO1 ;
Z#2 G#6 H#7 ;
#2 = ##5
#3003 = #8 OR 1 ;
G1 Z#3 ;
Dwell.
G4 P#4 ;
#3003 = #8 ;
G0 Z - #3 - #2 ;
Return.
N1 M99%
G83 (O830) Deep hole drill cycle
G. 1 ; Fixed cycle block 1 movement command

1F [#30] GOTO2 ; Check for fixed cycle invalidity.
#29 = #11 Define the cutting amount.
#28 = 0 Initialize the return amount (total cutting amount).
Z#2 G#6 H#7 ;
#2 = ##5
#3003 = #8 OR 1 ; Inhibit single block stop.
DO 1 ;
#28 = #28 - #11 Define the return amount of the next block.
#26 = - #28 - #29 Calculate the feed amount.
Z#26 ; Feed.
IF [ABS [#28] GE [ABS [#3] ] ] GOTO 1 ; Does the total cutting amount (return amount)
exceed the cut amount?
G1 Z#29 ; Cutting feed
IV - 20
G0 Z#28 ; Return.
#29 = #11 + #14 ; Define the cutting amount for block 2 and after.
END1 ;
N1 G1 Z#3 - #26 ; Cutting feed
#3003 = #8 ;
G0 Z - #3 - #2 ; Return.
N2 M99%
G84 (O840) Tap cycle

Z#2 G#6 H#7 ;
#2 = ##5
#3004 = #9 OR 3 ; Invalidate feed hold/override.
G1 Z#3 ;
G4 P#4 ; Dwell.
M4 ; Rotate the spindle reversely.
#3900 = 1 ;
G1 Z - #3 ;
#3004 = #9 ;
G4 P#4 ; Dwell.
M3 ; Rotate the spindle forward.
#3003 = #8 ;
G0 Z = #2 ; Return.
N1 M99%
G85 (O850) Boring 1

Z#2 G#6 H#7 ;
#2 = ##5
G1 Z#3 ;
#3003 = #8 ;
Z - #3 ;
G0 Z - #2 ; Return.
N1 M99%
IV - 21
G86 (O860) Boring 2

G. 1 ;
1F [#30] GOTO1 ;
Z#2 G#6 H#7 ;
#2 = ##5
#3003 = #8 OR 1 ;
G1 Z#3 ;
Dwell.
G4 P#4 ;
Stop the spindle.
M5 ;
Return.
G0 Z - #3 - #2 ;
#3003 = #8 ;
Rotate the spindle forward.
M3 ;
N1 M99%
G87 (O870) Back boring

M19 ; Orient the spindle.
X#12 Y#13 ;
#3003 = #8 ; Cancel single block stop inhibition.
Z#2 G#6 H#7 ;
G1 X - #12 Y - #13 ;
Z#3 ;
G0 X#12 Y#13 ; Shift.
Z - #2 - #3 ; G87 is not affected by the G98 or G99 modal.
X - #12 Y - #13 ; Shift.
N1 M99%
IV - 22
G88 (O880) Boring 3

G. 1 ; Check for fixed cycle invalidity.
1F [#30] GOTO1 ;
Z#2 G#6 H#7 ; Inhibit single block stop.
#2 = ##5
#3003 = #8 OR 1 ; Dwell.
G1 Z#3 ; Cancel single block stop inhibition.
G4 P#4 ; Rotate the spindle forward
#3003 = #8 ; Inhibit single block stop.
M5 ; Return.
#3003 = #8 OR 1 ; Cancel single block stop inhibition.
G0 Z - #3 - #2 ; Rotate the spindle forward.
#3003 = #8 ;
M3 ;
N1 M99 ;
G89 (O890) Boring 4

G. 1 ;
1F [#30] GOTO1 ;
Z#2 G#6 H#7 ;
#2 = ##5
#3003 = #8 OR 1 ;
G1 Z#3 ;
Dwell.
G4 P#4 ;
#3003 = #8
Z - #3 ;
Return.
G0 Z - #2 ;
N1 M99%
G73 (O831) Step cycle

G. 1 ; Check for fixed cycle invalidity.
1F [#30] GOTO2 ; Initialize the total cutting amount.
#29 = 0 Define the cutting amount.
#28 = #11 ;
Z#2 G#6 H#7 ;
#2 = ##5 Single block stop command
#3003 = #8 OR 1 ;
DO 1 ; Increment the total cutting amount counter.
#29 = #29 + #11 ; Does the total cutting amount exceed the cut
IF [ABS [#29] GE [ABS [#3] ] ] GOTO 1 ; amount Z?
IV - 23
G1 Z#28 ; Cutting feed

G4 P#4 ; Dwell.
G0 Z − #14 ; Return.
#28 = #11 + #14 ; Define the cutting amount for block 2 and after.
END1 ;
N1 G1 Z#3 − #29 + #28 ; Cutting feed
G4 P#4 ; Dwell.
#3003 = #8 ;
G0Z - #3 - #2 ; Return.
N2 M99%
G74 (O841) Reverse tap cycle

Z#2 G#6 H#7 ;
#2 = ##5
#3004 = #9 OR 3 ; Invalidate feed hold/override.
G1 Z#3 ;
G4 P#4 ; Dwell.
#3900 = 1 ;
Z - #3 ;
#3004 = #9 ;
G4 P#4 ; Dwell.
M4 ; Rotate the spindle reversely.
#3003 = #8 ;
G0 Z - #2 ;
N1 M99% Return.
IV - 24
G75 (O750) Circle cutting cycle
G. 1 ; Fixed cycle block 1 movement command.

IF [#30] GOTO 1 ; Check for fixed cycle invalidity.
#28=#18;
#2 = ##5
IF[#28GE0]GOTO2; Decide the circular direction.
#27=3#28=-#28; G03 circular
GOTO3;
N2 #27=2; G02 circular
N3 #26=[#[16000+#4]+#[17000+#4]]*#99;
IF[#26GE#28]GOTO1; Check compensation amount
Z#2G#6H#7;
#2=##5#3003=#8OR1;
G1Z#3;
#28=#28-#26#29=#28/2;
G#27X-#28I-#29; Inner circumference half lap
I#28P1; Outer circumference one lap
X#28I#29; Inner circumference half lap
#3003=#8;
G0Z-#3-#2; Return.
N1 M99%
G76 (O861) Fine boring

Z#2 G#6 H#7 ;
#2 = ##5
#3003 = #8 OR 1 ; Single block stop command
G1 Z#3 ;
X#12 Y#13 ; Shift.
G0 Z − #3 − #2 ; Return.
#3003 = #8 ;
Shift.
X − #12 Y − #13 ;
Rotate the spindle forward.
M3 ;
N1 M99%
IV - 25
Appendix 5. RS-232C I/O Device Parameter Setting Examples
Appendix 5. RS-232C I/O Device Parameter Setting Examples
Cable connection NC I/O NC I/O NC I/O NC I/O NC I/O Follows

1 1 1 1 1 1 1 1 1 1 communication
2 2 2 2 2 2 2 2 2 2 protocol.
3 3 3 3 3 3 3 3 3 3 (NC side)
4 4 14 14 4 4 4 4 4 4 2 : SD
5 5 5 5 5 8 5 5 5 5
3 : RD
6 6 6 6 6 6 6 6 6
20 20 20 20 20 20 20 20 20
4 : RS
7 7 7 7 8 8 8 8 8 5 : CS
7 7 7 7 7 7 6 : DR
Parameter 20 : ER
setting examples 7 : GND
DEVICE NAME Follows
BAUD RATE 2 2 2 2 2 communication
software.
STOP BIT 3 3 3 3 3
PARITY EFFECTIVE 0 0 0 0 0
EVEN PARITY 0 0 0 0 0
CHR. LENGTH 3 3 3 3 3
HAND SHAKE 3 2 3 3 3
DC CODE PARITY 1 0 1 1 1
DC2/DC4 OUTPUT 0 0 1 0 1
CR OUTPUT 0 0/1 0 0 0
FEED CHR. 0 0 0 0 0
PARITY V 0 0 0 0/1 0/1
TIME-OUT SET 100 100 100 100 100
IV - 26
Appendix 6. Alarms
6.1 List of Alarms
Appendix 6. Alarms
6.1 List of Alarms
6.1.1 Operation Alarms
(The bold characters are the messages displayed on the screen.)

MUU Message {{{{
Error No.
Message
Class
(1) Class: M01 Operation error

Alarms occurring due to incorrect operation by the operator during NC operation and those by machine
trouble are displayed.
Error No. Details Remedy

0001 Dog overrun • Increase the length of the near-point dog.
When returning to the reference position‚ the • Reduce the reference position return speed.
near-point detection limit switch did not stop
over the dog‚ but overran the dog.
0002 Some ax does not pass Z phase • Move the detector one rotation or more in the
One of the axes did not pass the Z-phase opposite direction of the reference position‚ and
during the initial reference position return after repeat reference position return.
the power was turned ON.
0003 R-pnt direction illegal • The selection of the AXIS SELECTION key's
When manually returning to the reference +/- direction is incorrect. The error is canceled
position‚ the return direction differs from the by feeding the axis in the correct direction.
axis movement direction selected with the AXIS
SELECTION key.
0004 External interlock axis exists • As the interlock function has activated‚ release
The external interlock function has activated it before resuming operation.
(the input signal is "OFF") and one of the axes • Check the sequence on the machine side.
has entered the interlock state. • Check for broken wires in the interlock signal
line.
0005 Internal interlock axis exists • The servo OFF function is valid‚ so release it
The internal interlock state has been entered. first.
The absolute position detector axis has been • An axis that can be removed has been issued‚
removed. so perform the correct operations.
A command for the manual/automatic • The command is issued in the same direction
simultaneous valid axis was issued from the as the direction where manual skip turned ON‚
automatic mode. so perform the correct operations.
• During the manual/automatic simultaneous
mode‚ the axis commanded in the automatic
mode became the manual operation axis. Turn
OFF the manual/automatic valid signal for the
commanded axis.
• Turn ON the power again‚ and perform
absolute position initialization.
0006 H/W stroke end axis exists • Move the machine manually.
The stroke end function has activated (the input • Check for broken wires in the stroke end signal
signal is "OFF") and one of the axes is in the wire.
stroke end status. • Check for trouble in the limit switch.
IV - 27
Appendix 6. Alarms
6.1 List of Alarms

0007 S/W stroke end axis exists • Move it manually.
The stored stroke limit I‚ II‚ IIB or IB function • If the stored stroke limit in the parameter is
has activated. incorrectly set‚ correct it.
0008 Chuck/tailstock stroke end ax • Reset the alarm with reset‚ and move the
The chuck/tail-stock barrier function turned ON‚ machine in the reverse direction.
and an axis entered the stroke end state.
0009 Ref point return No. invalid • Execute No. 1 reference position return.
Return to the No. 2 reference position was
performed before return to the No. 1 reference
position was completed.
0019 Sensor signal illegal ON • Turn the tool measurement mode signal input
The sensor signal was already ON when the OFF, and move the axis in a safe direction.
tool measurement mode (TLM) signal was • The operation alarm will turn OFF even when
validated. the sensor signal is turned OFF.
The sensor signal turned ON when there was (Note) When the tool measurement mode signal
no axis movement after the tool measurement input is turned OFF, the axis can be
mode (TLM) signal was validated.
moved in either direction. Pay attention to
The sensor signal turned ON at a position the movement direction.
within 100μm from the final entry start position.
0020 Ref point retract invalid • Execute reference position return
Return to the reference position was performed
before the coordinates had not been
established.
0021 Tool ofs invld after R-pnt • The error is cleared if the operation mode is
Reference position return was performed changed to other than reference position return
during tool retract return, and therefore the tool before the axis performs reference position
compensation amount became invalid after return.
reference position return was completed. • The error is cleared when reference position
return is completed.
• The error is cleared if reset 1 is input or the
emergency stop button is pushed.
0024 R-pnt ret invld at abs pos alm • Reset the absolute position detection alarm‚
A zero point return signal was input during an and then perform zero point return.
absolute position detection alarm.
0025 R-pnt ret invld at zero pt ini • Complete zero point initialization‚ and then
A zero point return signal was input during zero perform zero point return.
point initialization of the absolute position
detection system.
0030 Now skip on • Increase the skip return amount.
The skip signal remains input when the skip
return operation changed to the measurement
operation.
0031 No skip • Check whether the measurement target has
Even though 1st skip was to the correct moved.
position, the 2nd skip could not be found.
0050 Chopping axis R-pnt incomplete • Reset or turn the chopping signal OFF, and
The chopping axis has not completed zero then carry out zero point return.
point return before entering the chopping
mode.
All axes interlock will be applied.
IV - 28
Appendix 6. Alarms
6.1 List of Alarms

0051 Synchronous error excessive • Select the correction mode and move one of
The synchronization error of the master and the axes in the direction in which the errors are
slave axes exceeded the allowable value under reduced.
synchronous control. • Increase the allowable value or reset it to 0
A deviation exceeding the synchronization error (check disabled).
limit value was found with the synchronization • When using simple C-axis synchronous
deviation detection. control, set the contents of the R435 register to
0.
• Check the parameter (#2024 synerr).
0053 No spindle select signal • Turn ON the spindle select signal (SWS)
Synchronous tapping command was issued responding to the tapping spindle before
when the spindle select signals (SWS) for all performing the synchronous tapping command.
spindles were OFF in the multiple-spindle
control II.
0054 No spindle serial connection • Make sure the spindle select signal (SWS) for
Synchronous tapping command was issued the responding spindle is ON.
when the spindle that the spindle select signal • When issuing a command, consider the
(SWS) was ON was not serially connected in machine construction.
the multiple-spindle control II.
0055 Spindle fwd/rvs run para err • Change the value of the parameter #3028
Asynchronous tapping command was issued sprcmm.
when M code of the spindle frd/rvs run
command set by the parameter "#3028
sprcmm" was one of the followings in the
multiple-spindle control II.
• One of M0, M1, M2, M30, M98, M99, M198
• M code No. that commands macro interrupt
signal valid/invalid
0056 Tap pitch/thread number error • Check the pitch/thread number and rotation
The command of the pitch/thread number is not speed of the tapping spindle.
correct in the synchronous tapping command of
the multiple-spindle control II.
The pitch is too small for the spindle rotation
speed.
Thread number is too large for the spindle
rotation speed.
0060 Handle ratio too large • Set a smaller ratio.
Handle ratio is too large for the rapid traverse
rate (or external deceleration speed when
external deceleration is valid).
0065 R-pos offset value illegal • Set the reference position offset value (#2034
At the start of reference position initial setting, rfpofs) to 0, then turn the power ON again to
setting of reference position offset value (#2034 perform reference position initial setting.
rfpofs) is other than 0.
0066 R-pos scan distance exceeded • Check the scale to see if it has dirt or damage.
Reference position could not be established • Check if the servo drive unit supports this
within the maximum scan distance. function.
IV - 29
Appendix 6. Alarms
6.1 List of Alarms

0101 No operation mode • Check for a broken wire in the input mode
signal wire.
• Check for trouble in the mode selector switch.
• Check the sequence program.
0102 Cutting override zero • Set the "cutting feed override" switch to a value
The "cutting feed override" switch on the other than zero to clear the error.
machine operation panel is set to zero. • When the "cutting feed override" switch is set to
The override was set to "0" during a single a value other than zero‚ check for a short circuit
block stop. in the signal wire.
0103 External feed rate zero • Set "the manual feed speed" switch to a value
"The manual feed speed" switch on the other than zero to release the error.
machine operation panel is set to zero when • If "the manual feed speed" switch is set to a
the machine is in the jog mode or automatic dry value other than zero‚ check for a short circuit
run mode. in the signal wire.
The "Manual feedrate B speed" is set to zero • Check the sequence program.
during the jog mode when manual feedrate B is
valid.
The "each axis manual feedrate B speed" is set
to zero during the jog mode when each axis
manual feedrate B is valid.
0104 F 1-digit feed rate zero • Set the F1-digit feedrate on the setup
The F1-digit feedrate is set to zero when the parameter screen.
F1-digit feed command is being executed.
0105 Spindle stop • Rotate the spindle.
The spindle stopped during the synchronous • If the workpiece is not being cut‚ start dry run.
feed command. • Check for a broken wire in the spindle encoder
cable.
• Check the connections for the spindle encoder
connectors.
• Check the spindle encoder pulse.
• Reconsider the program. (Command, address)
0106 Handle feed ax No. illegal • Check for broken wires in the handle feed axis
An axis not found in the specifications was selection signal wire.
designated for handle feed or the handle feed • Check the sequence program.
axis was not selected. • Check the No. of axes listed in the
specifications.
0107 Spindle rotation speed over • Lower the commanded spindle rotation speed.
The spindle rotation speed exceeded the axis
clamp speed during the thread cutting
command.
0108 Fixed pnt mode feed ax illegal • Check for broken wires in the fixed mode feed
An axis not found in the specifications was axis selection signal wire and fixed point mode
designated for the fixed point mode feed or the feedrate wire.
fixed point mode feedrate is illegal. • Check the fixed point mode feed specifications.
0109 Block start interlock • Check the sequence program.
An interlock signal that locks the start of the
block has been input.
0110 Cutting block start interlock • Check the sequence program.
An interlock signal that locks the start of the
cutting block has been input.
IV - 30
Appendix 6. Alarms
6.1 List of Alarms

0111 Restart switch ON • Search the block to be restarted.
The restart switch was turned ON before the • Turn OFF the restart switch.
restart search was completed, and the manual
mode was selected.
0112 Program check mode • Press the reset button to cancel the program
The automatic start button was pressed during check mode.
program check or in program check mode.
0113 Auto start in buffer correct • Press the automatic start button after buffer
The automatic start button was pressed during correction is completed.
buffer correction.
0115 In reset process • When rewinding the tape‚ wait for the winding
The automatic start button was pressed during to end‚ or press the reset button to stop the
resetting or tape rewinding. winding‚ and then press the automatic start
button.
• During resetting‚ wait for resetting to end‚ and
then press the automatic start button.
0117 Playback not possible • During editing‚ cancel the function by pressing
The playback switch was turned ON during the input or previous screen key‚ and then turn
editing. ON the playback switch.
0118 Turn stop in normal line cntrl • Check the program.
The turning angle at the block joint exceeded • Set the normal line control axis turning speed.
the limit during normal line control. (Parameter "#1523 C_feed")
• Set the C axis turning diameter smaller than the
Normal line control type I arc radius, or check the setting value of the C
The normal line control axis turning speed axis turning diameter.
(#1523 C_feed) has not been set. (Parameter "#8041 C rot. R")
Normal line control type II
When turning in the inside of the arc, the
parameter "#8041 C-rot. R" setting value is
larger than the arc radius.
0120 In synchronous correction mode • Select the handle or manual feed mode.
The synchronous correction mode switch was • Turn OFF the correction mode switch.
pressed in a non-handle mode.
0121 No synchronous control option • Set 0 in register R2589.
The synchronous control system (register
R2589) was set with no synchronous control
option.
0123 Computer link B not possible • Perform the cycle start after resetting is
The cycle start was attempted before resetting completed.
was completed. • Set 0 in "#8109 HOST LINK", and then set 1
An attempt was made to perform computer link again before performing the cycle start.
B operation at the second part system and • The computer link B operation cannot be
following in a multi-part system. performed at the second part system and
following in a multi-part system.
0124 X/Z axes simultaneous prohibit • Turn the inclined axis and basic axis start OFF
The basic axis corresponding to the inclined for both axes. (This also applied for
axis was started simultaneously in the manual manual/automatic simultaneous start.)
mode while the inclined axis control was valid. • Invalidate the basic axis compensation, or
command one axis at a time.
IV - 31
Appendix 6. Alarms
6.1 List of Alarms

0125 Rapid override zero • Set the "rapid traverse override" switch to a
The "rapid traverse override" switch on the value other than zero to clear the error.
machine operation panel is set to zero. • When the "rapid traverse override" switch is set
to a value other than zero, check for a short
circuit in the signal wire.
0126 Program restart machine lock • Release the machine lock before resuming
Machine lock was applied on the return axis operations.
while manually returning to the restart position.
0127 Rot axis parameter error • Review the rotational axis configuration
The orthogonal coordinate axis name does not parameters.
exist.
The rotary axis name does not exist.
The orthogonal coordinate axis name is
duplicated.
The number of axes that were selected to
change tool length compensation along the tool
axis amount exceeds the maximum number of
axes.
The orthogonal coordinate axis name is that of
the rotary axis name.
0150 Chopping override zero • Check the chopping override (R2530).
The override became "0" while performing the • Check the rapid traverse override (R2502).
chopping operation.
0151 Command axis chopping axis • Reset, or turn OFF the chopping signal. When
A chopping axis movement command was the chopping signal is turned OFF, the axis will
issued from the program during the chopping return to the reference position, and then the
mode. (This alarm will not occur when the program movement command will be executed.
movement amount is commanded as 0.)
(All axes interlock state will be applied.)
0153 Bottom dead center pos. zero • Correctly set the bottom dead center position.
The bottom dead center position is set to the
same position as the upper dead center
position.
0154 Chopping disable for handle ax • Select an axis other than the chopping axis as
Chopping was started when the chopping axis the handle axis, or start chopping after
was selected as the handle axis. changing the mode to another mode.
0160 No speed set out of soft limit • Set the maximum speed for the outside of the
Returned from the outside of the soft limit range soft limit range. (Parameter "#2021 out_f")
for the axis with no maximum speed set for the • Change the soft limit range.
outside of the soft limit range. (Parameter "#2013 OT-" "#2014 OT+")
0170 Ill. op during T tip control • Change to the previous operation mode and
An attempt was made to perform an incorrect reboot.
operation during tool tip center control.
1005 G114.n command illegal • Cancel with G113.
An attempt was made to execute G114.n • Issue the spindle synchronous cancel signal
during execution of G114.n. (Y18B8: SPSYC).
G51.2 was commanded when the G51.2 • Cancel with G50.2.
spindle-spindle polygon machining mode was • Cancel with the spindle-spindle polygon cancel
already entered with a separate part system. signal (YCD1).
1007 Spindle in-use by synchro tap • Cancel synchronized tapping.
The spindle is being used in synchronized
tapping.
IV - 32
Appendix 6. Alarms
6.1 List of Alarms

1026 SP-C ax ctrl runs independntly • Cancel the C axis command.
C axis mode command was issued for polygon • Cancel the polygon machining command.
machining spindle. • Cancel the C axis with servo OFF.
C axis mode command was issued for
synchronized tapping spindle.
Polygon command was issued for
synchronized tapping spindle.
Spindle is being used as spindle/C axis.
1030 Synchronization mismatch • Correct the program so that the M codes
Different M codes were commanded in the two match.
part systems as the synchronization M codes. • Correct the program so that the same
Synchronization with the "!" code was synchronization codes are commanded.
commanded in another part system during M
code synchronization.
Synchronization with the M code was
commanded in another part system during
synchronization with the "!" code.
1031 Multiple C axes select invalid • Check and correct the parameters and
The C axis selection signal was changed when program.
multiple C axes could not be selected.
An axis that cannot be controlled as the
multiple C axes selection was selected.
1032 Tap retract Sp select illegal • Select the spindle for which tap cycle was
Tap return was executed when a different halted before the tap return signal was turned
spindle was selected. Cutting feed will wait until ON.
synchronization is completed.
1033 Sp-Sp polygon cut interlock • Wait for synchronization to end.
Cutting feed will wait until synchronization is
completed.
1034 Mixed sync ctrl prmtr illegal • Check the parameter settings for mixed
Mixed synchronization control exceeding the synchronization control.
number of control axes was attempted.
Mixed synchronization control with duplicated
axis addresses was attempted.
1035 Mixed sync ctrl disable modal • Check the program.
Mixed synchronization was commanded for a
part system in which mixed synchronization
control is disabled as shown below.
• During nose R compensation mode
• During pole coordinate interpolation mode
• During cylindrical interpolation mode
• During balance cut mode
• During fixed cycle machining mode
• During facing turret mirror image
IV - 33
Appendix 6. Alarms
6.1 List of Alarms

1036 Synchro ctrl setting disable • Set the R2589 register to 0.
The synchronous control operation method
selection (R2589 register) was set when the
mode was not the C axis mode.
The synchronous control operation method
selection (R2589 register) was set in the zero
point not set state.
Mirror image disable state • Check the program and parameters.
The external mirror image or parameter mirror
image was commanded during facing turret
mirror image.
1037 Synchro start/cancel disable • Check the program and parameters.
Synchronous control was started or canceled
when synchronous control could not be started
or canceled.
1038 Move cmnd invld to synchro ax • Check the program.
A movement command was issued to a
synchronous axis in synchronous control.
1106 Sp synchro phase calc illegal • Check the program.
The spindle synchronization phase alignment • Check the sequence program.
command was issued while the spindle
synchronization phase calculation request
signal was ON.
(2) Class: M90 Message: Parameter set mode

M90 Messages output when the setup parameter lock function is enabled are displayed.

- Setup parameter lock released Refer to the manual issued by the machine tool
The setup parameter lock is released. builder.
Automatic start is disabled when setup
parameters can be set.
IV - 34
Appendix 6. Alarms
6.1 List of Alarms
6.1.2 Stop Codes

These codes indicate a status that caused the controller to stop for some reason.

TUU Message {{{{
Error No.
Message
Class
(1) Class: T01 Cycle start prohibit

This indicates the state where automatic operation cannot be started when attempting to start it from the
stop state.

0101 Axis in motion • Try automatic start again after all axes have
Automatic start is not possible as one of the stopped.
axes is moving.
0102 NC not ready • Another alarm has occurred. Check the details
Automatic start is not possible as the NC is not and remedy.
ready.
0103 Reset signal ON • Turn OFF the reset input signal.
Automatic start is not possible as the reset • Check that the reset switch is not ON
signal has been input. constantly due to trouble.
0104 Auto operation pause signal ON • Check the FEED HOLD switch.
The FEED HOLD switch on the machine • The feed hold switch is the B contact.
operation panel is ON (valid). • Check for broken wires in the feed hold signal
wire.
0105 H/W stroke end axis exists • If one of the axis' ends is at the stroke end‚
Automatic start is not possible as one of the move the axis manually.
axes is at the stroke end. • Check for broken wire in the stroke end signal
wire.
• Check for trouble in the stroke end limit switch.
0106 S/W stroke end axis exists • Move the axis manually.
Automatic start is not possible as one of the • If an axis is not at the end‚ check the parameter
axes is at the stored stroke limit. details.
0107 No operation mode • Select the automatic operation mode.
The operation mode has not been selected. • Check for broken wires in the automatic
operation mode (memory‚ tape‚ MDl) signal
wire.
0108 Operation mode duplicated • Check for a short circuit in the mode selection
Two or more automatic operation modes are signal wire (memory‚ tape‚ MDl).
selected. • Check for trouble in the switch.
0109 Operation mode changed • Return to the original automatic operation
The automatic operation mode changed to mode‚ and start automatic start.
another automatic operation mode.
IV - 35
Appendix 6. Alarms
6.1 List of Alarms

0110 Tape search execution • Begin automatic start after the tape search is
Automatic start is not possible as tape search is completed.
being executed.
0112 Restart pos. return incomplete • Manually return to the restart position.
Automatic start is not possible as the axis has • Turn the automatic restart valid parameter ON,
not been returned to the restart position. and then execute automatic start.
0113 CNC overheat • The NC controller temperature has exceeded
Automatic start is not possible because a the specified temperature.
thermal alarm (Z53 CNC overheat) has • Take appropriate measures to cool the unit.
occurred.
0115 Cycle st. prohibit(Host comm.) • Execute automatic start after the
Automatic start cannot be executed as the NC communication with the host computer is
is communicating with the host computer. completed.
0116 Cycle st prohibit(Battery alm) • Replace the battery of the NC control unit.
Automatic start cannot be executed because • Contact the service center.
the voltage of the battery inserted in the NC
control unit has dropped.
0117 R-pnt offset value not set • Perform the initial reference position setting,
As the reference position offset value has not then set the reference position offset value
been set, automatic operation cannot be used. (#2034 rfpofs).
0138 In absolute position alarm • Reset the absolute position detection alarm‚
A start signal was input during an absolute and then input the start signal.
position detection alarm.
0139 In abs posn initial setting • Complete zero point initialization before
A start signal was input while initializing the inputting the start signal.
absolute position detector's zero point.
0180 Cycle start prohibit • Set "0" to "#1164 ATS" when the servo auto
Automatic start is disabled in servo auto turning turning is not executed.
valid.
0190 Cycle start prohibit • Refer to the manual issued by the machine tool
Automatic start is disabled because setup builder.
parameters can be set.
0191 Cycle start prohibit • Cause automatic start after file deletion or
Automatic start was caused during file deletion writing is completed.
or writing.
0193 Cycle st. prohibit (Term exp'd) • Enter the decryption code and turn the power
Automatic start is disabled because the valid ON again.
term has been expired.
IV - 36
Appendix 6. Alarms
6.1 List of Alarms
(2) Class: T02 Feed hold

The feed hold state been entered due to a condition in the automatic operation.

0201 H/W stroke end axis exists • Manually move the axis away from the stroke
An axis is at the stroke end. end limit switch.
• The machining program must be corrected.
0202 S/W stroke end axis exists • Manually move the axis.
An axis is at the stored stroke limit. • The machining program must be corrected.
0203 Reset signal ON • The program execution position has returned to
The reset signal has been input. the start of the program. Execute automatic
operation from the start of the machining
program.
0204 Auto operation pause signal ON • Resume automatic operation by pressing the
The FEED HOLD switch is ON. "CYCLE START" switch.
The operation mode changed to another mode mode‚ and resume automatic operation by
during automatic operation. pressing the "CYCLE START" switch.
0206 Acc/dec time cnst too large • Increase the set value of the parameter "#1206
The acceleration and deceleration time G1bF".
constants are too large. (This problem occurs • Decrease the set value of the parameter
at the same time as system alarm Z59.) "#1207 G1btL".
• Lower the cutting speed.
0215 Abs posn detect alarm occurred • Reset the absolute position detection alarm.
An absolute position detection alarm occurred.
(3) Class: T03 Block stop

This indicates that automatic operation stopped after executing one block of the program.

0301 Single block stop signal ON • Automatic operation can be resumed by turning
The SINGLE BLOCK switch on the machine the CYCLE START switch ON.
operation panel is ON.
The single block or machine lock switch
changed.
0302 Block stop cmnd in user macro • Automatic operation can be resumed by turning
The block stop command was issued in the the CYCLE START switch ON.
user macro program.
The automatic mode changed to another mode‚ and resume automatic operation by
automatic mode. turning the CYCLE START switch ON.
0304 MDI completed • Set MDI again‚ and turn the CYCLE START
The last block of MDI was completed. switch ON to resume MDl operation.
0305 Block start interlock • Check the sequence program.
The interlock signal that locks the block start is
entered.
0306 Cutting blck start interlock • Check the sequence program.
The interlock signal that locks the block cutting
start is entered.
0310 Inclined Z offset change • Automatic operation can be restarted by turning
Whether to validate the offset of the inclined ON the CYCLE START switch.
Z-axis switched during program operation.
IV - 37
Appendix 6. Alarms
6.1 List of Alarms
(4) Class: T04 Collation stop

This indicates that collation stop was applied during automatic operation.

0401 Collation stop • Automatic operation can be restarted with
Collation stop occurred. automatic start.
(5) Class: T10 Fin wait

This indicates the operation state when an alarm did not occur during automatic operation‚ and nothing
seems to have happened.
Error No. Details

0 The error number is displayed while each of the completion wait modes listed in the table below is
ON. It disappears when the mode is canceled.
Alarm Unclamp In dwell Alarm Door Waiting Alarm Waiting Waiting Waiting Waiting
No. signal execu- No. open for No. for for for rapid for MSTB
wait tion spindle spindle cutting traverse comp-
position orienta- speed decelera- letion
to be tion to deceleration
(Note 2) (Note 1) looped complete tion
0 0 0
1 × 1 × 1 ×
8 × 8 × 2 ×
9 × × 9 × × 3 × ×
4 ×
5 × ×
6 × ×
7 × × ×
8 ×
9 × ×
A × ×
B × × ×
C × ×
D × × ×
E × × ×
F × × × ×
(Note 1) This mode is enabled by the door interlock function.

(Note 2) The system is waiting for the index table indexing unclamp signal to turn ON or OFF
IV - 38
Appendix 6. Alarms
6.1 List of Alarms
6.1.3 Servo/Spindle Alarms

This section describes alarms occurred by the errors in the servo system such as the drive unit‚ motor and
encoder, etc. The alarm message‚ alarm No. and axis name will display on the alarm message screen. The
axis where the alarm occurred and the alarm No. will also display on the servo monitor screen and the spindle
monitor screen respectively. If several alarms have occurred‚ up to two errors per axis will display on the
servo monitor screen and the spindle monitor screen respectively.
(Note 1) The alarm class and alarm reset class combinations are preset.
Alarm class Alarm reset class Resetting methods
S01 PR After removing the cause of the alarm, reset the
alarm by turning the NC power ON again.
S02 PR After correcting the parameter, reset the alarm by
turning ON the NC power again.
S03 NR After removing the cause of the alarm, reset the
alarm by inputting the NC RESET key.
S04 AR After removing the cause of the alarm, reset the
alarm by turning the drive unit power ON again.
S51 - This is cleared if a correct value is set.
S52 - -
(Note 2) The resetting method may change according to the alarm class.
For example, even if "S03 SERVO ALARM: NR" is displayed, it may be necessary to turn the NC
power ON again.

S{{ Message : xx ΔΔΔΔ
Servo : Axis name
Axis name
Spindle : "S", "T", "M", "N"
Alarm No. (Parameter No.)
Alarm reset class
Message
Alarm class
(1) Class: S01/S03/S04 Servo alarm

Alarm No. Message Meaning
0010 Insufficient voltage Insufficient PN bus voltage was detected in main circuit.
0011 Axis selection error Setting of the axis No. selection switch is incorrect.
0012 Memory error 1 A CPU error or an internal memory error was detected during the
power ON self-check.
0013 Software processing Software processing has not finished within the specified time.
error 1
0014 Software processing Software processing has not finished within the specified time.
error 2
0015 Memory error 2 A CPU error or an internal memory error was detected during the
power ON self-check.
0016 Magnet pole pos An error was detected in the magnetic pole detection for controlling
detect error the motor.
0017 A/D converter error An error was detected in the A/D converter for detecting current FB.
0018 Motor side dtc: Init Initial communication with the motor end detector failed.
commu err
IV - 39
Appendix 6. Alarms
6.1 List of Alarms

0019 Detector commu err Initial communication with the motor end detector on master axis
in syn cont failed when setting closed-loop current synchronous control. Or the
communication was interrupted.
001A Machine side dtc: Initial communication with the linear scale or the ball screw end
Init comu er detector failed.
001B Machine side dtc: The machine side detector detected an error.
Error 1 As details defer from detector to detector, refer to the separate table
001C Machine side dtc: (1).
Error 2
001D Machine side dtc:
Error 3
001E Machine side dtc:
Error 4
001F Machine side dtc: An error was detected in communication data with the linear scale or
Commu error the ball screw end detector. Or the communication was interrupted.
0020 Motor side dtc: No When an excessive error alarm occurred, no signal from the motor
signal side detector was detected.
0021 Machine side dtc: When an excessive error alarm occurred, no signal from the
No signal machine side detector was detected.
0023 Excessive speed A difference between the speed command and speed feedback was
error continuously exceeding 50 r/min for longer than the setting time.
0024 Grounding The motor power cable is in contact with FG (Frame Ground).
0025 Absolute position The absolute position was lost, as the backup battery voltage
data lost dropped in the absolute position detector.
0026 Unused axis error A power module error occurred in the axis whose axis No. selection
switch was set to "F"(free axis).
0027 Machine side dtc: The machine side detector detected an error.
Error 5 As details defer from detector to detector, refer to the separate table
(1).
0028 Machine side dtc:
Error 6
0029 Machine side dtc:
Error 7
002A Machine side dtc:
Error 8
002B Motor side dtc: The motor side detector (linear scale in the case of linear motor)
Error 1 detected an error.
002C Motor side dtc: As details defer from detector to detector, refer to the separate table
Error 2 (1).
002D Motor side dtc:
Error 3
002E Motor side dtc:
Error 4
002F Motor side dtc: An error was detected in communication data with the motor end
Commu error detector or with the linear scale of a linear servo system. Or the
communication was interrupted.
0030 Over regeneration Over-regeneration detection level became over 100%. The
regenerative resistor is overloaded.
0031 Overspeed The motor was detected to rotate at a speed exceeding the
allowable speed. (In the case of linear motor, it was detected to
move at a speed exceeding the allowable speed.)
IV - 40
Appendix 6. Alarms
6.1 List of Alarms

0032 Power module Overcurrent protection function in the power module has started its
overcurrent operation.
0033 Overvoltage PN bus voltage in main circuit exceeded the allowable value.
0034 NC-DRV commu: An error was detected in the data received from the CNC.
CRC error
0035 NC command error The travel command data that was received from the CNC was
excessive.
0036 NC-DRV commu: The communication with the CNC was interrupted.
Commu error
0037 Initial parameter An incorrect parameter was detected among the parameters
error received from the CNC at the power ON.
0038 NC-DRV commu: An error was detected in the communication frames received from
Protocol error 1 the CNC.
0039 NC-DRV commu: An error was detected in the axis information data received from the
Protocol error 2 CNC.
003A Overcurrent Excessive current was detected in the motor drive current.
003B Power module Thermal protection function in the power module has started its
overheat operation.
003C Regeneration circuit An error was detected in the regenerative transistor or in the
error regenerative resistor.
003D Spindle speed The spindle motor failed to rotate faster than 45 r/min, even when
blocked the max. torque command was given.
003E Spindle speed 1. The spindle motor speed feedback was detected to be
overrun accelerated exceeding the commanded speed.
2. The spindle motor was detected to be rotated at a speed
exceeding the parameter value, while the speed command was
"0" (including the case of operation stoppage during the position
control).
0040 Detector select unit An error was detected in the motor switching signals that were
swtch err received from the detector selection unit, while controlling one drive
unit and two motors.
0041 Detector select unit An error was detected in the communication with the detector
commu err selection unit, while controlling one drive unit and two motors.
0042 Feedback error 1 An error was detected in the feedback signals of the position
detector in a servo system, or in PLG's feedback signals in a spindle
system.
0043 Feedback error 2 Excessive difference was detected in position data between the
motor end detector and the machine end detector in a servo system.
In a spindle system, an error was detected in the encoder feedback
signals.
0044 Inappropriate coil When using a coil changeover motor, C-axis was controlled while
for C axis the high-speed coil was selected.
0045 Fan stop A cooling fan built in the drive unit stopped, and the loads on the unit
exceeded the specified value.
0046 Motor overheat Thermal protection function of the motor or in the detector, has
started its operation.
0047 Regenerative Thermal protection function of the regenerative resistor, has started
resistor overheat its operation.
IV - 41
Appendix 6. Alarms
6.1 List of Alarms

0048 Motor side dtc: The motor side detector (linear scale in the case of linear motor)
Error 5 detected an error.
0049 Motor side dtc: As details defer from detector to detector, refer to the separate
Error 6 table (1).
004A Motor side dtc:
Error 7
004B Motor side dtc:
Error 8
004C Current err at mag A current error was detected in the IPM spindle motor when the
pole detect initial magnetic pole was being formed.
004E NC command mode The mode outside the specification was input in spindle control
error mode selection.
004F Instantaneous The power was momentarily interrupted.
power interrupt
0050 Overload 1 Overload detection level became over 100%. The motor or the
drive unit is overloaded.
0051 Overload 2 Current command of more than 95% of the unit's max. current was
being continuously given for longer than 1 second in a servo system.
In a spindle system, current command of more than 95% of the
motor's max. current was being continuously given for longer than 1
second.
0052 Excessive error 1 A difference between the actual and theoretical motor positions
during servo ON exceeded the setting value.
0053 Excessive error 2 A difference between the actual and theoretical motor positions
during servo OFF exceeded the setting value.
0054 Excessive error 3 When an excessive error 1 occurred, detection of the motor current
failed.
0055 External emergency There is no contactor shutoff command, even after 30 seconds has
stop error passed since the external emergency stop was input.
0058 Collision detection When collision detection function was valid, the disturbance torque
1: G0 in rapid traverse (G0) exceeded the collision detection level.
0059 Collision detection When collision detection function was valid, the disturbance torque
1: G1 in cutting feed (G1) exceeded the collision detection level.
005A Collision detection 2 When collision detection function was valid, the command torque
reached the max. Motor torque.
005B Sfty obsrvation: In safety monitoring mode, the command speed was detected to
Cmd spd err exceed the safe speed.
005C Orientation After orientation was achieved, a difference between the command
feedback error and feedback exceeded the parameter setting.
005D Sfty obsrvation: In safety monitoring mode, the door state signal from the NC and the
Door stat err same signal from the drive unit don't match. Otherwise, door open
state was detected in normal mode.
005E Sfty obsrvation: FB In safety monitoring mode, the motor speed was detected to exceed
speed err the safe speed.
005F External contactor A contact of the external contactor is welding. Or the contactor fails
error to be ON during ready ON.
0060 Pw sply:Inst pw It was detected that the 24VDC power supply lowered.
interpt(DC24V)
0061 Pw sply: Pwr Overcurrent protection function in the power module has started its
module overcurnt operation.
IV - 42
Appendix 6. Alarms
6.1 List of Alarms

0062 Pw sply: Frequency The input power supply frequency increased above the specification
error range.
0063 Pw sply: The supplementary regenerative transistor is being ON.
Supplement regen
err
0065 Pw sply: Rush relay A resistor relay for rush short circuit fails to be ON.
error
0067 Pw sply: Phase An open-phase condition was detected in input power supply circuit.
interruption
0068 Pw sply: Watchdog The system does not operate correctly.
0069 Pw sply: Grounding The motor power cable is in contact with FG (Frame Ground).
006A Pw sply: Ext A contact of the external contactor is welding.
contactor weld
006B Pw sply: Rush relay A resistor relay for rush short circuit fails to be OFF.
welding
006C Pw sply: Main An error was detected in charging operation of the main circuit
circuit error capacitor.
006D Pw sply: Parameter The capacity of the power supply unit and the regenerative resistor
error type that was set in the parameter are mismatched.
006E Pw sply: Memory An error was detected in the internal memory or A/D converter.
error/AD error
006F Power supply error No power supply is connected to the drive unit, or a communication
error was detected.
0070 Pw sply: Ext A mismatch of the external emergency stop input and CNC
emergency stp err emergency stop input continued for 30 seconds.
0071 Pw sply: Instant pwr The power was momentarily interrupted.
interrupt
0072 Pw sply: Fan stop A cooling fan built in the power supply unit stopped, and overheat
occurred in the power module.
0073 Pw sply: Over Over-regeneration detection level became over 100%. The
regeneration regenerative resistor is overloaded. This alarm cannot be reset for
15 min from the occurrence. Leave the drive system emergized for
more than 15 min, then turn the power ON to reset the alarm.
0074 Pw sply: Regen Thermal protection function of the regenerative resistor, has started
resist ovheat its operation.
0075 Pw sply: L+ and L- bus voltage in main circuit exceeded the allowable value.
Overvoltage As the voltage between L+ and L- is high immedialtey after this
alarm, another alarm may occur if this alarm is reset in a short time.
Wait more than 5 min before resetting so that the voltage drops.
0076 Pw sply: Ext EMG As for the external emergency stop settings, the setting on the rotary
stop set err switch and the parameter setting are mismatched.
0077 Pw sply: Power Thermal protection function in the power module has started its
module overheat operation.
007F Drv unit pw supply A mismatch of program mode selection was detected. Turn the
restart req drive unit power ON again.
0087 Drive unit Answers from a drive unit connected to the power supply stopped.
communication
error
0088 Watchdog The system does not operate correctly.
IV - 43
Appendix 6. Alarms
6.1 List of Alarms
Separate table (1)

Alarm number when motor
002B 002C 002D 002E
end is connected
Alarm number when machine
001B 001C 001D 001E
end is connected
OSA105 -
LED error
Detector type OSA166 CPU error Data error -
MDS-B-HR - -
A CPU initial error Deterioration of the An error was
Meaning of alarm -
was detected. LED was detected. detected in the data.

0048 0049 004A 004B
end is connected
0027 0028 0029 002A
end is connected
OSA105 - - - -
OSA166 - - - -
Detector type
MDS-B-HR Communication
Connection error Judgment error Magnetic error
error
An error was An error was The linear scale An error was
detected in the detected in the analog frequency detected in the
Meaning of alarm connection with the communication with cycle could not be magnetic data for
analog output linear the serial output judged. the linear servo
scale. linear scale. system.

002B 002C 002D 002E
end is connected
001B 001C 001D 001E
end is connected
TS5690 - -
Detector type Initialization error Waveform error
TS5691 - -
An initialization error An error was
was detected when detected in the A, B,
Meaning of alarm - -
the power was Z analog signal
turned ON. waveform.

0048 0049 004A 004B
end is connected
0027 0028 0029 002A
end is connected
TS5690 - - Relative position
Detector type Overspeed
TS5691 - - data error
The tolerable An error was
rotation speed was detected in the
Meaning of alarm - -
exceeded. relative position
data.
IV - 44
Appendix 6. Alarms
6.1 List of Alarms

002B 002C 002D 002E
end is connected
001B 001C 001D 001E
end is connected
Manufacturer
Detector type
name
AT342 Photo-electric type,
AT343 Mitsutoyo static capacity data
mismatch
AT543
LC191M ROM/RAM error
Initialization error EEPROM error Relative/absolute
LC491M
position data
RCN723 Heidenhain mismatch
RCN223
ERM280 - -
MJ831 Sony - - - -
Faulty mounting Detection position
ADB-20J60 MHI - Scale disconnected
accuracy deviated
Futaba
FMD Denshi - - - -
Kogyo

0048 0049 004A 004B
end is connected
0027 0028 0029 002A
end is connected
Manufacturer
Detector type
name
AT342
Photo-electric type Static capacity type Photo-electric type
AT343 Mitsutoyo
overspeed error error
AT543
LC191M
CPU error
LC491M Absolute position
data error Absolute position
RCN723 Heidenhain Overspeed
data error
RCN223
ERM280 -
MJ831 Sony - - - Encoder error
ADB-20J60 MHI - - Gain fault Phase fault
Futaba
FMD Denshi - - Waveform error Excessive speed
Kogyo
IV - 45
Appendix 6. Alarms
6.1 List of Alarms
(2) Class: S02 Message: Initial parameter error

An error was found in the parameters transmitted from the controller to the drive unit when the power
was turned ON.
Remove the cause of the alarm, and then reset the alarm by turning the controller power OFF once.
Alarm
Details Remedy
No.
2201 The servo parameter setting data is illegal. Check the descriptions for the appropriate servo
to The alarm No. is the No. of the servo parameter parameters and correct them.
2264 where the error occurred.
2301 The number of constants to be used in the Check that all the related parameters are
following functions is too large: specified correctly.
• Electronic gears sv001:PC1, sv002:PC2, sv003:PGN1
• Position loop gain sv018:PIT, sv019:RNG1, sv020:RNG2
• Speed feedback conversion
2302 When high-speed serial incremental detector Check that all the related parameters are
(OSE104, OSE105) is connected, parameters for specified correctly.
absolute position are set to ON. sv017:SPEC, sv025:MTYP
Set the parameters for absolute position
detection to OFF.
To detect an absolute position, replace the
incremental specification detector with an
absolute position detector.
2303 No servo option is found. Check that all the related parameters are
The closed loop (including the ball screw- specified correctly.
end detector) or dual feedback control is an sv025:MTYP/pen
optional function. sv017:SPEC/dfbx
The SHG control is an optional function. specified correctly.
sv057:SHGC
sv058:SHGCsp
The adaptive filtering is an optional function. specified correctly.
sv027:SSF1/aflt
13001 Parameter error Check the descriptions for the appropriate
to The spindle parameter setting data is illegal. spindle parameters and correct them.
13256 The alarm No. is the No. of the spindle Refer to Alarm No.37 in Spindle Drive
parameter where the error occurred. Maintenance Manual.
(3) Class: S51 Message: Parameter error

This warning is displayed if a parameter outside the tolerance range is set.
Illegal settings will be ignored.
This alarm will be reset when a correct value is set.
Alarm
Details Remedy
No.
2201 Servo parameter setting data is illegal. Check the descriptions for the appropriate servo
to The alarm No. is the No. of the servo parameter parameters and correct them.
2264 where the warning occurred.
13001 Spindle parameter setting data is illegal. Check the descriptions for the appropriate
to The alarm No. is the No. of the spindle spindle parameters and correct them.
13256 parameter where the warning occurred. Refer to Spindle Drive Maintenance Manual.
IV - 46
Appendix 6. Alarms
6.1 List of Alarms
(4) Class: S52 Servo warning

Displays servo and spindle tool warnings.
0093 Init abs pos fluctuation The position data have fluctuated during the absolute position
initializing.
0096 Scale feedback error An excessive deviation was detected between the motor end
detector and MP scale feedback data in a MP scale absolute
position detection system.
0097 Scale offset error An error was detected in the offset data received from the MP scale
in a MP scale absolute position detection system.
009B Detector converting An error was detected in the shift distance of the magnetic pole in a
unit: Magnetic pole shift linear servo system.
warning
009E Absolute position An error was detected in the revolution counter of the absolute
detector: Revolution position detector. The absolute position data cannot be
counter error compensated.
009F Battery voltage drop The battery voltage that is supplied to the absolute position detector
dropped. The absolute position data is retained.
00A6 Fan stop warning A cooling fan built in the drive unit stopped.
00A8 Turret indexing warning The designated position shift amount of turret indexing is outside
the setting range.
00A9 Orientation feedback As an orientation feedback error occurred, the retrial has been
warning conducted.
00E0 Overregeneration Over-regeneration detection level exceeded 80%.
warning
00E1 Overload warning Overload detection level exceeded 80%.
00E2 Continuous high-speed The motor was continuously rotated at a speed exceeding the rated
revolution warning speed.
00E3 Absolute position Deviation between the absolute and relative position data was
counter warning detected.
00E4 Set parameter warning An incorrect parameter was detected among the parameters
received from the CNC.
00E6 Control axis Control axis detachment was commanded.
detachment warning
00E7 In NC emergency stop Emergency stop was input from the CNC.
state
00E8 Power supply: Over Regeneration that are beyond the power supply limitation has
supplementary frequently occurred.
regeneration frequency
00E9 Instantaneous power The power was momentarily interrupted.
interruption warning
00EA In external emergency External emergency stop signal was input.
stop state
00EB Power supply: Over Over-regeneration detection level exceeded 80%.
regeneration warning
00EE Pw sply: Fan stop A cooling fan built in the power supply unit stopped.
warning
IV - 47
Appendix 6. Alarms
6.1 List of Alarms
6.1.4 MCP Alarm

An error has occurred in the drive unit and other interfaces. (The bold characters are the messages displayed
on the screen.)
YUU Message {{{{ {{{{
Alarm No.
Error No.
Message
Class
IV - 48
Appendix 6. Alarms
6.1 List of Alarms
(1) Class: Y02 System alarm

An error occurred in the data transmitted between the MCP and drive unit after the power was turned
ON.

0050 System alm: Process time over The software or hardware may be damaged.
Contact the service center.
0051 Alarm No. A communication error has occurred between the
SV commu er: CRC error 1 controller and drive unit.
0000 • Take measures against noise.
(10 times/910.2 ms)
• Check that the communication cable connector
SV commu er: CRC error 2 between the controller and drive unit and one
0001
(2 continuous times) between the drive units are tight.
SV commu er: Recv timing err • Check whether the communication cable
0002 between the controller and drive unit and one
(2 continuous times)
between the drive units are disconnected.
xy03 SV commu er: Data ID error • A drive unit may be faulty. Take a note of the
(2 continuous times) 7-segment LED contents of each drive unit and
x: Channel No. (0 to) report to the Service Center.
y: Drive unit rotary switch No. • Update the drive unit software version.
(0 to)
xy04 SV commu er: Recv frame No.
(2 continuous times)
x: Channel No. (0 to)
y: Number of reception frame -1
(0 to)
x005 SV commu er: Commu error
(No error classification)
x006 SV commu er: Connect error
xy20 SV commu er: Init commu error
The drive unit could not shift to the
initial communication run time and
stopped.
y: Drive unit rotary switch No.
(0 to)
xy30 SV commu er: Node detect error
No response from drive unit to the
request from NC when setting
network configuration.
y: Station No. (0 to)
xy31 SV commu er: Commu not
support
SV commu er: Communication
mode not supported
Drive unit's software version
doesn't support the
communication mode that the
controller requires.
y: Station No. (0 to)
(Note) When two or more "Y02 System alarms" occur at the same time, only the alarm which occurs first is
displayed.
IV - 49
Appendix 6. Alarms
6.1 List of Alarms
(2) Class: Y03 Message: Drive unit unequipped

The drive unit is not correctly connected.

Alphabet Servo axis drive unit not mounted Check the drive unit mounting state.
(axis • Check the end of the cable wiring.
name) • Check the cable for broken wires.
1 to 4 PLC axis drive unit not mounted • Check the connector insertion.
• The drive unit input power is not being input.
S No.1 spindle axis drive unit not mounted • The drive unit axis No. switch is illegal.
T No.2 spindle axis drive unit not mounted
M No.3 spindle axis drive unit not mounted
N No.4 spindle axis drive unit not mounted
(3) Class : Y05 Message: Initial parameter error

Details Remedy
There is a problem in the value set for the number of axes or Check the value set for the corresponding
the number of part systems. parameters.
#1001 SYS_ON
#1002 axisno
#1039 spinno, etc.
(4) Class: Y06 Message: mcp_no setting error

There are differences in the MCP and axis parameters when the NC power is turned ON.

0001 There is a skipped number in the channels. Check the values set for the following
parameters.
0002 The random layout setting is duplicated.
#1021 mcp_no
0003 The drive unit fixed setting "0000" and random #3031 smcp_no
layout setting "∗∗∗∗" are both set.
0004 The spindle/C axis "#1021 mcp_no" and "#3031
smcp_no" are not set to the same values.
0005 A random layout is set for the "#1154 pdoor" =1
two-part system.
0006 The channel No. parameter is not within the
setting range.
IV - 50
Appendix 6. Alarms
6.1 List of Alarms
(5) Class: Y07 Message: Too many axes connected

The number of connected axes exceeds the number allowed in the system.
(Alarm No.)
0 0
Exceeded number of axes

at drive unit interface channel 1
Exceeded number of axes
Alarm No. Details Remedy

0000 The number of axes connected to each Remove connected axes from the channel
to channel exceeds the maximum number of whose alarm No. is other than 0 for the
00FF connectable axes. number displayed as the alarm No. Keep the
The exceeded number of axes per channel number of connected axes to or less than the
is displayed as alarm No. maximum that can be connected.
This alarm occurs when the drive unit is
connected only with the 2nd channel without
connecting with the 1st channel.
(Note 1) The number of axes is limited per each drive unit interface channel.
(Note 2) Maximum number of axes that can be connected differs depending on whether or not an
expansion unit is available or the setting of "#11012 16 axes for 1ch". The maximum number of
connectable axes is as shown below.
Maximum number of axes to be connected
Extension unit #11012 16 axes for 1ch
(Per 1 channel)
Yes 0/1
8 axes
0
No
1 16 axes
(Note 3) If this alarm occurs, the alarm "Y03 Message: Drive unit unequipped" will not occur.
(Note 4) This alarm is displayed taking precedence over the alarm "Y08 Too many drive units connected"
and "Y09 Too many axisno connected".
IV - 51
Appendix 6. Alarms
6.1 List of Alarms
(6) Class: Y08 Message: Too many drive units connected

The number of connected drive units exceeds the number allowed in the system.
(Alarm No.)
0 0
Exceeded number of drive units

Exceeded number of drive units


0000 The number of drive units connected to each Remove drive units from the channel whose
to channel exceeds 8. alarm No. is other than 0 for the number
00FF The exceeded number of drive units per displayed as the alarm No. Keep the number
channel is displayed as alarm No. of connected drive units to 8 or less.
(Note 1) The drive unit is not counted when all the axes connected to it are invalid.
(Note 3) The alarm "Y07 Too many axes connected" and "Y09 Too many axisno connected" are
displayed taking precedence over this alarm.
IV - 52
Appendix 6. Alarms
6.1 List of Alarms
(7) Class: Y09 Message: Too many axisno connected

The connected axes No. (drive unit's rotary switch No.) is bigger than the No. allowed in the system.
(Alarm No.)
0 0
"1" when the axis No. at drive unit interface channel 1

is too big
"1" when the axis No. at drive unit interface channel 2

is too big

0000 The No. of the axis (drive unit's rotary switch For the channel whose alarm No. is 1, keep
to No.) connected to each channel is bigger the axis No. (drive unit's rotary switch No.)
0011 than the No. allowed. not bigger than the No. allowed.
(Note 1) The axis No. is limited per each drive unit interface channel.
(Note 2) The biggest allowed connected axis No. differs depending on whether or not an expansion unit
is available or the setting of "#11012 16 axes for 1ch". The biggest connectable axis No. is as
shown below.
Highest allowed connected axis No.

Extension unit #11012 16 axes for 1ch
(Per 1 channel)
Yes 0/1
0 to 7
No 0
1 0 to F
(Note 4) This alarm is displayed taking precedence over the alarm "Y08 Too many drive units
connected".
(Note 5) The alarm "Y07 Too many axes connected" is displayed taking precedence over this alarm.
IV - 53
Appendix 6. Alarms
6.1 List of Alarms
(8) Class: Y20 Safety observation alarm

When this alarm is output, emergency stop mode is applied.
Refer to "remedy" of each alarm as to how to cancel the alarm.
Error No. Alarm No. Details Remedy
0001 Axis name Parameter compare error The NC or the servo drive unit may be
The speed monitoring parameter damaged.
in the NC and the parameter Contact the service center.
transmitted to the drive unit are not
matched.
The name of the axis with an error
is displayed.
0002 Axis name Sfty obsrvation: Cmd spd err Check the speed monitoring parameter
The speed exceeding the speed and the user PLC.
set with the parameter was Restart the NC.
commanded during the speed
monitoring mode.
is displayed.
0003 Axis name Sfty obsrvation: FB pos err The NC or the servo drive unit may be
The commanded position damaged.
transmitted to the servo drive unit Contact the service center.
from NC and the feedback position
to be received from the servo drive
unit are totally different during the
speed monitoring mode.
is displayed.
0004 Axis name Sfty obsrvation: FB speed err Check the speed observation parameter
Actual rotation speed of the motor and the user PLC.
is exceeding the speed set with Restart the NC.
speed monitoring parameter
during the speed monitoring mode.
is displayed.
0005 Door No. Door signal: Input mismatch Check the cable.
Door state signals on the NC side Check the door switch.
and the drive side do not match. It Restart the NC.
may be caused by the followings:
• Cable disconnection
• Damaged door switch
• Damaged NC or servo drive unit
0006 Door No. No spd obsv mode in door open Check the user PLC.
The door open state was detected Restart the NC.
when the speed monitoring mode
was invalid.
The causes may be same as the
ones for 0005 (Door signal: Input
mismatch). Also the user PLC may
not be correct.
IV - 54
Appendix 6. Alarms
6.1 List of Alarms

0007 Axis name Speed obsv: Para incompatible Change the relevant parameters so that
Two speed monitoring parameters the two speed monitoring parameters
are not matched at the rising edge match.
of the speed monitoring mode Restart the NC.
signal.
is displayed.
0008 Contactor Contactor welding detected Make sure that contactor's auxiliary b
No. Contactor welding was detected. contact signal is output correctly to the
device set on "#1380 MC_dp1" and
"#1381 MC_dp2".
If welding, replace the contactor.
Restart the NC.
0009 - No spec: Safety observation Turn OFF the servo parameter SV113/bitF,
The servo parameter and the the spindle parameter SP229/bitF and the
spindle parameter of the speed spindle type servo parameter SV113/bitF.
monitor are set for a system with Then, restart the NC.
no safety observation option.
0010 - SDIO connector input volt err Check the wiring. Supply 24VDC power to
24VDC power is not supplied to the SDIO connector.
SDIO connector correctly. (SDIO Restart the NC.
4A pin supply voltage was dropped
to 16V or less, or 1ms or more
instant power interrupt was
detected.)
In this case, "Pw sply:Inst pw
interpt(DC24V)" alarm occurs
because the contactor control
output signal cannot be controlled.
This state remains until restarting
the NC even if the cause of the
alarm has been removed.
(9) Class: y21 Safety observation warning

The warning will be cancelled when the cause of the warning is removed.
0001 Axis name Speed obsv signal: Speed over When decelerated, the warning will be
The speed exceeds the safety removed, and the speed monitor will be
speed limit when the speed started.
monitoring mode signal is ON.
is displayed.
IV - 55
Appendix 6. Alarms
6.1 List of Alarms
(10) Class: Y51 Parameter error

An error occurred in a parameter that causes an alarm while the control axis was operating.

0001 Parameter G0tL illegal • Check "#2004 G0tL".
The time constant has not been set or the
setting exceeded the setting range.
0002 Parameter G1tL illegal • Check "#2007 G1tL".
0003 Parameter G0t1 illegal • Check "#2005 G0t1".
0004 Parameter G1t1 illegal • Check "#2008 G1t1".
0009 Parameter grid space illegal • Check "#2029 grspc".
0012 Parameter stapt1-4 illegal • Check spindle parameters" #3017 stapt1" to
The time constant has not been set or the "#3020 stapt4".
0015 Parameter skip_tL illegal • Check "#2102 skip_tL".
0016 Parameter skip_t1 illegal • Check "#2103 skip_t1".
0017 Parameter G0bdcc illegal • Check "#1205 G0bdcc".
"#1205 G0bdcc" for the 2nd part system is set
to acceleration/deceleration before G0
interpolation.
0018 OMR-II parameter error • Check the related parameter settings.
The OMR-II related parameter settings are
incorrect. In this case, the OMR-II is disabled.
0101 Values of PC1/PC2 too large • Check "#2201 PC1" and "#2202 PC2".
The PC1 and PC2 settings used for the rotary
axis are too large.
IV - 56
Appendix 6. Alarms
6.1 List of Alarms
(11) Class: Y90 Message: No spindle signal
(Alarm No.) Z open B open A open

Alarm No. phase phase phase
0 0 1 ×
No.1 spindle
2 ×
No.2 spindle
3 × ×
4 ×
No.3 spindle
5 × ×
No.4 spindle
6 × ×
7 × × ×
Alarm
Details Remedy
No.
0001 There is an error in the spindle encoder signal. • Check the spindle encoder's feedback cable
to The data transmission to the drive unit is stopped and the encoder.
0007 when this error occurs.
IV - 57
Appendix 6. Alarms
6.1 List of Alarms
6.1.5 System Alarms

Z31 DataServer error {{{{
Warning No.
Message
Warning No. Explanation

0001 Socket open error(socket)
0002 Socket bind error(bind)
0003 Connection wait queue error(listen)
0004 Connection request error(accept)
0005 Data recv error(socket error)
0006 Data recv error(data error)
0007 Data send error(socket error)
0008 Data send error(data error)
000A Socket close error(close)
(Note) If warning No. 0001, 0002, 0003, or 000A is displayed, set the parameters, then turn power OFF and
turn it ON again.
IV - 58
Appendix 6. Alarms
6.1 List of Alarms

Message Details Remedy
Z40 This appears when the parameter MemVal • Either return the MemVal setting, or format
Format is formatted at 0, and MemVal is set to 1. and restart.
mismatch
Z51 <Type> • If the same alarm is output by the same
E2PROM error Z51 E2PROM error 0011: Read error operation, the cause is an H/W fault.
00xx Z51 E2PROM error 0012: Write error Contact the Service Center.
Z52 The voltage of the battery inserted in the NC • Replace the battery of the NC control unit.
Battery fault control unit has dropped. (The battery used • Check for disconnection of the battery
000x to save the internal data.) cable.
0001: Battery warning • After treating the battery‚ check the
0002: Battery detecting circuit error machining program.
0003: Battery alarm
(Note 1)
Z53 The controller or operation board • Cooling measures are required.
CNC overheat temperature has risen above the designated • Turn OFF the controller power‚ or lower
value. (Note 2) the temperature with a cooler‚ etc.
Z55 This occurs when an error occurs in the • Check and replace the cables.
RIO communication between the controller and • Replace the remote I/O unit.
communication remote l/O unit. • Check the power supply. (existence of
stop • Cable breakage supply‚ voltage)
• Remote l/O unit fault
• Power supply to remote l/O unit fault
(Note 3)
Z57 The program memory capacity setting value Check the state of the following items.
System warning cannot be formatted. • Program memory capacity
The expansion cassette (HR437) is not • Status of expansion cassette (HR437)
mounted after formatting. mounting
An expansion cassette different from the • APLC open option
expansion cassette (HR437) mounted
during formatting is mounted.
Z58 The machine tool builder macro program • Write the machine tool builder macro
ROM write not was not written to the FROM after being program to the FROM.
completed registered, edited, copied, condensed,
• If the operations, such as editing, done
merged, the number changed, or deleted.
while the NC power was OFF can be
invalidated, the program does not need to
be written to the FROM.
Z59 Acceleration and deceleration time • Increase the value specified as the "#1206
Acc/dec time constants are too large. G1bF" parameter.
cnst too large (This alarm is output at the same time as • Decrease the value specified as the
"T02 Acc/dec time cnst too large 0206.") "#1207 G1btL" parameter.
• Lower the feedrate.
Z60 Communication error has occurred on the • Refer to (Note 4) for details.
Fieldbus Fieldbus communication using
communi- HN571/HN573/HN575.
cation error
Z64 The valid term will be expired in less than a • Obtain a decryption code by making a
Valid term soon week. Remaining valid term is xx more days. payment. Enter the decryption code.
to be expired
xx
Z65 No decryption code was input before the • Obtain a decryption code by making a
Valid term has valid term was expired. payment. Enter the decryption code.
been expired
IV - 59
Appendix 6. Alarms
6.1 List of Alarms

Z67 A communication error occurred during • Refer to "List of Messages" in CC-Link
CC-Link CC-Link communication using (Master/Slave) Specification manual
communication HN566/HN576. (BNP-C3039-214).
error
Z68 The cable connected between • Connect the cable.
CC-Link HN566/HN576 and each device is • Check whether or not the cable is broken.
unconnected disconnected or broken.
! CAUTION
Do not replace the battery while the power is ON.
Do not short circuit, charge, heat, incinerate or disassemble the battery.
Dispose of the spent battery following local laws.
(Note 1) The display of Z52 battery fault 0001 can be removed by resetting. However, the warning state will
not be cancelled until the battery is replaced.
(Note 2) Temperature warning
If the alarm is displayed when an overheat alarm is detected‚ the overheat signal will be output
simultaneously. If the machine is in automatic operation‚ the operation will be continued‚ but
restarting will not be possible after resetting or stopping with M02/M30. (Starting will be possible
after block stop or feed hold.) The alarm will be reset and the overheat signal will turn OFF when the
temperature drops below the specified temperature.
Z53 CNC overheat 000x

↑
0001 : The temperature in the controller is high.
0002 : The temperature around the communication terminal
(setting and display unit) is high.
0003 : The temperature in the controller and around the communication
terminal (setting and display unit) is high.
The ambient temperature must be lowered immediately when a "Z53 CNC overheat" alarm occurs‚
but if machining must be continued‚ the alarm can be invalidated by turning the following parameter OFF.
76543210
PLC parameter bit selection #6449
Communication terminal
(setting and display unit) 0: Detection invalid
Controller 1: Detection valid
IV - 60
Appendix 6. Alarms
6.1 List of Alarms
(Note 3) RIO communication interrupt

If communication between the control unit and remote I/O unit fails, the alarm and remote I/O unit
number are displayed.
(a)(b) Board connection remote I/O
communication interrupted station
↓↓
Z55 RIO communication stop
Remote I/O 3rd part system

Remote I/O 1st part system
Remote I/O 2nd part system
(a) and (b) above indicate the following matters.
Alarm RIO RIO RIO RIO Alarm RIO RIO RIO RIO
number (seventh (sixth (fifth (fourth number (third (second (first (0th
station) station) station) station) station) station) station) station)
0 0
1 × 1 ×
2 × 2 ×
3 × × 3 × ×
4 × 4 ×
5 × × 5 × ×
6 × × 6 × ×
7 × × × 7 × × ×
8 × 8 ×
9 × × 9 × ×
A × × A × ×
B × × × B × × ×
C × × C × ×
D × × × D × × ×
E × × × E × × ×
F × × × × F × × × ×
This also applies for the remote I/O 1st part system communication interrupted station, remote I/O 3rd part
system communication interrupted station and board connection remote I/O communication interrupted
station.
IV - 61
Appendix 6. Alarms
6.1 List of Alarms
(Note 4)
Z60 Fieldbus communication error n1 n2 n3 n4
Classification No.
Message
Class.
Details
No.
n1 Shows state of the master channel (shown in hexadecimal number)
00: Offline In initializing
40: Stop Cutting I/O communication
80: Clear Resetting output data of each slave by sending 0 data.
C0: In operation In I/O communication
n2 Shows error state (shown in hexadecimal number)
Bit 7 6 5 4 3 2 1 0
BIT Details
0 Control error: Parameter error
1 Auto clear error: Communication with all the slave channels was cut because
a communication with one slave channel had an error.
2 Non exchange error: Slave channel with communication error is found
3 Fatal error: The communication cannot be continued because sever network
failure exists.
4 Event error: Short-circuit was found on the network.
5 Not ready: CNC communication is not ready.
6 Time out error: Time out was detected in communication with each channel.
7 Not used
n3 Shows error No. (shown in hexadecimal number)

Refer to "(a) Error in master channel" and "(b) Error in slave channel" for details.
n4 Shows slave No. where communication error has occurred. (shown in hexadecimal
number)
"FF" means an error in master channel.
IV - 62
Appendix 6. Alarms
6.1 List of Alarms
(a) Error in master channel (when remote address with an error is FF (hexadecimal number))
Value in
Details Remedy
n3
0 No error Operating normally
32 No USR_INTF-task Damage in HN571. Replace HN571.
33 No global data field
34 No FDL-task
35 No PLC-task
37 Master parameter incorrect
39 Slave parameter incorrect
3C Data offset exceeding allowable set Check the configuration setting.
value received
3D Slave data send range overlap
3E Slave data receive range overlap
3F Not set data hand shake Damage in HN571. Replace HN571.
40 RAM range exceeded
41 Slave parameter data set illegal
CA No segment
D4 Data base read illegal Download the configuration data again.
D5 Operating system illegal Damage in HN571. Replace HN571.
DC Watch dog error
DD Hand shake mode
No data communication by 0
DE Master auto clear mode When setting auto clear mode, the auto clear
mode was performed because one slave was
not able to connect in run time.
(b) Error in slave channel (when remote address with an error is other than FF (hexadecimal
number))
Value in
Details Remedy
n4
2 Station overflow reported Check the configuration of slave channel in
3 Station stopped responding to which error has occurred. Check if there is
master command any short-circuit in wire to bus.
9 No slave required responding data
11 No station respond
12 No master to logical token ring
15 Illegal parameter requested
IV - 63
Appendix 6. Alarms
6.1 List of Alarms
6.1.6 Absolute Position Detection System Alarms

ZUU Message {{{{
Axis name
Error No.
Message
Class
(1) Class: Z70 Abs data error

This error is displayed if the absolute position data is lost in the absolute position detection system.
Alarm reset Servo
Error Zero point
Details Remedy when power alarm
No. initialization
is turned OFF No.
0001 Abs posn base set Complete zero point Required - -
incomplete initialization.
Zero point initialization is
incomplete.
Otherwise, the spindle was
removed.
0002 Absolute position lost Input the parameters. If the (Required) - -
The absolute position reference point data cannot be
reference point data saved in restored‚ perform zero point
the NC has been destroyed. initialization.
0003 Abs posn param changed Correctly set the parameters. Required - -
The parameters used to Turn the power on again‚ and
detect the absolute position perform zero point initialization.
have been changed.
#1003 iunit #2201 PC1

#1016 iout #2202 PC2
#1017 rot #2218 PIT
#1018 ccw #2219 RNG1
#1040 M_inch #2220 RNG2
#2049 type #2225 MTYP
0004 Abs posn initial set illegal Reperform zero point Required - -
The zero point initialization initialization.
point is not at the grid
position.
0005 Abs posn param restored Turn the power on again‚ and Not required - -
Restoration was possible operation will be possible.
with parameter input in the
above No.0002 state.
0080 Abs posn data lost Replace the detector and Required - (9E)
The absolute value data was complete zero point etc.
lost, because the initialization.
multi-rotation counter data in
the detector was incorrect,
etc.
IV - 64
Appendix 6. Alarms
6.1 List of Alarms
Alarm reset Servo

Error Zero point
No. initialization
is turned OFF No.
0101 Abs posn error(servo alm 25) Reperform zero point Required - (25)
The power was turned ON initialization.
again after the servo alarm
No. 25 displayed.
0106 Abs posn error(servo alm Reperform zero point Required - (E3)
E3) initialization.
The power was turned ON
again after the servo alarm
No. E3 displayed.
(Note) To release alarm "Z70 Abs data error", enter the parameter data output when establishing the
absolute position and turn ON the power again. For the rotary axis, however, the alarm cannot be
released by entering the parameter data.
(2) Class: Z71 Abs encoder failure

This alarm is displayed if an error is found in the detector for the absolute position detection system.
Alarm reset Servo
Error Zero point
No. initialization
is turned OFF No.
0001 AbsEncoder:Backup voltage Replace the battery‚ check the Required - 25
drop cable connections‚ and check (Z70-0101
The backup voltage in the the detector. Turn the power displays after
absolute position detector ON again‚ and perform zero power is
dropped. point initialization. turned ON
again.)
0003 AbsEncoder: Commu error Check and replace the cables‚ (Required) Reset 91
Communication with the card or detector. Turn the Only when
absolute position detector power ON again‚ and perform detector is
was not possible. zero point initialization. replaced.
0004 AbsEncoder: Abs data Check and replace the cables‚ (Required) Reset 93
changed card or detector. Turn the Only when
The absolute position data power ON again‚ and perform detector is
fluctuated when establishing zero point initialization. replaced.
the absolute position.
0005 AbsEncoder: Serial data Check and replace the cables‚ (Required) Reset 92
error card or detector. Turn the Only when
An error was found in the power ON again‚ and perform detector is
serial data from the absolute zero point initialization. replaced.
position detector.
0006 AbsEncoder: Abs/inc posn Operation is possible until the (Required) Reset E3
diffr power is turned off. When power (Z70-0106
Servo alarm E3 is turned ON displays after
Absolute position counter again. power is
warning turned ON
again.)
0007 AbsEncoder: Initial commu Check and replace the cables‚ (Required) Reset 18
err card or detector. Turn the Only when
Initial communication with the power ON again‚ and perform detector is
absolute position detector zero point initialization. replaced.
was not possible.
IV - 65
Appendix 6. Alarms
6.1 List of Alarms
(3) Class: Z72 Message: Position check error

This alarm is displayed if an error is detected when comparing the detector's absolute position and
controller coordinate values in the absolute position system.
(4) Class: Z73 Message: Absolute position data warning

This warning is displayed for the absolute position detection system.
Alarm
Details Remedy
No.
0001 Battery for abs data fault If the battery voltage is low or the cable is
Servo alarm 9F damaged, there is no need to initialize the
Low battery voltage absolute position.
(Note) When this alarm occurs, do not turn OFF the drive unit power to protect the absolute position data.
Replace the battery while the drive unit power is ON.
IV - 66
Appendix 6. Alarms
6.1 List of Alarms
6.1.7 Distance-coded Reference Scale Errors

ZUU Message {{{{
Axis name
Error No.
Message
Alarm class
(1) Class: Z80 Distance-coded ref scale err

Error
Details Remedy
No.
0001 Basic position lost • Input the parameter. If the basic point data
The basic point data memorized by the NC is cannot be recovered, perform the initial
broken. reference position setting.
0002 Basic position restore • Operation can be started after turning the power
The basic point data is recovered by ON.
parameter input.
0003 No spec: Distance-coded scale • Check the specification.
Even if the distance-coded reference scale is • If you do not use this function, set the detector
not included in the specification, it is set to be type in servo parameters correctly.
available.
IV - 67
Appendix 6. Alarms
6.1 List of Alarms
6.1.8 Messages during Emergency Stop
EMG Emergency stop

Error items
Error Item Details Remedy

PLC The user PLC has entered the emergency stop • Investigate and remove the cause of the user
state during the sequence process. PLC emergency stop.
EXIN The emergency stop input signal for machine • Cancel the emergency stop input signal.
operation board or handy terminal is significant • Check the wiring to see if any wiring is broken.
(open).
SRV An alarm occurred in the servo system causing • Investigate and remove the cause of the servo
an emergency stop. alarm.
STOP The user PLC (ladder sequence) is not running. • Check if the rotary switch CS2 on the top of the
controller front panel is set to 1.
• Check if the PLC edit file save screen (onboard
function) [4RUN/SP] (run/stop) switch is turned
ON.
SPIN Spindle drive unit not mounted • Cancel the causes of the other emergency
The spindle drive unit is not mounted. stop.
• Check emergency stop signal input in the
spindle drive unit.
PC_H High-speed PC processing abnormal • Check the sequence program.
(To stop monitoring the high-speed PC
processing temporarily, set 1 in "#1219
aux03/bit1". Disable the monitoring function
only as a temporary measure.)
PARA Setting of the door open II fixed device is illegal. • Specify the "#1155 DOOR_m" and "#1156
The dog signal random assignment parameter DOOR_s" parameters correctly.
setting is illegal. (When the door open II fixed device is not
used, set "#1155 DOOR_m" and "#1156
DOOR_s" to "100".)
• Correctly set the "#2073 zrn_dog", "#2074
H/W_OT+", "#2075 H/W_OT-" and "#1226
aux10/bit5" parameters.
IV - 68
Appendix 6. Alarms
6.1 List of Alarms

LINK If the FROM/TO instruction is not executed within • Try to execute the FROM or TO instruction one
500 ms, an emergency stop occurs. or more times every 500 ms.
* Measure the time in which no interrupt request
is issued from MELSEC and store the result in
the R register.
R10190: Current time-out counter
R10191: Counter for maximum time-out after
power-on
R10192: Counter for maximum time-out after
system start-up (backed up)
MELSEC is held in error and reset states. • Check the MELSEC states.
The contents of MELSEC-specific code area in • Check the MELSEC states.
buffer memory have been destroyed.
PLC serial link communication has stopped. • Check that HR571 card wiring and external
sequencer transmission are normal.
(Note) When "WAIT" is entered for the PLC
• Check the diagnostic screen for link
serial link, only the preparation sequence
communication errors.
has been established before the
• Check whether the basic specification
communication stops. Therefore, it is
parameters related to serial link parameters are
supposed that the basic specification
specified correctly.
parameters related to serial link
parameters #1902 and #1903 are
incorrect or the #1909 set-time is too
short.
WAIT The preparation sequence is not sent from the • Check that the HR571 card rotary switch and
master station. Otherwise, the contents of the wiring and the external sequencer transmission
received preparation sequence are inconsistent are normal.
with those of the parameters, so that the usual • Check the diagnostic screen for link
sequence cannot be started. communication errors.
(Note) When "LINK" is also entered for the PLC
serial link, refer to "Note" in the section,
"LINK".
XTEN The HR571 card operates abnormally or the • Check the HR571 card rotary switch and
rotary switch is set incorrectly. replace the HR571 card if required.
LAD The user PLC (ladder sequence) has an illegal • Check the user PLC (ladder sequence) to see if
code. it uses illegal device numbers or constants.
CVIN The external emergency stop function for power • Cancel the emergency stop input signal.
supply is valid. So, the emergency stop input • Check the wiring to see if any wiring is broken.
signal for power supply is significant (open).
MCT An emergency stop occurs because the • Automatically cancel the emergency stop after
contactor shutoff test is executing. the contactor shutoff is confirmed.
• When the contactor shutoff cannot be
confirmed within 5 seconds after contactor
shutoff test signal (Y742) is input, "Y20
Contactor welding detected" alarm will occur,
and the emergency stop status remains.
• Turn the power ON again after confirming
"contactor's auxiliary b contact" signal is
correctly output to the device that is set with
"#1330 MC_dp1" and "#1331 MC_dp2".
IV - 69
Appendix 6. Alarms
6.1 List of Alarms
6.1.9 Auxiliary Axis Alarms

Refer to "1.3 Servo/spindle alarms" for details of the alarm class and alarm clear class combination.

S{{ Message UUUU
Axis No. 1 to 4
Alarm information
(Follows MR-J2-CT alarm information)
Message
Alarm class
(1) Class: S01 Aux ax servo alarm

Alarm
Details Remedy
information
0011 Aux ax PCB err (Drive circuit) • Replace servo drive unit.
An error occurred in the drive unit's internal PCB.
0013 Aux ax S/W processing error • Replace servo drive unit.
An error occurred in the drive unit's internal reference
clock.
0016 Aux ax motor/detector type err
Motor type error. • Use a correct drive unit and motor
combination.
Detector initial communication error. • Connect correctly.
• Replace the motor.
• Replace or repair cable.
Detector CPU error. • Replace the motor (detector).
0017 Aux ax PCB error(A/D err) • Replace servo drive unit.
An error occurred in the drive unit's internal A/D converter.
0025 Aux ax absolute posn lost • Turn the power ON for 2 to 3
An error occurred in the detector's internal absolute minutes while the alarm is
position data. occurring, and then turn the power
ON again.
• Replace the battery, and initialize
the absolute position again.
0034 Aux ax CRC error • Take countermeasures against
An error occurred in the communication with the NC. noise.
0036 Aux ax communication timeout • Connect correctly.
Communication with the NC was cut off. • Turn the NC power ON.
• Replace the drive unit or NC.
0037 Aux ax parameter error • Set the parameter correctly.

The parameter setting value is incorrect.
0038 Aux ax frame error • Take countermeasures against
An error occurred in the communication with the NC. noise.
0039 Aux ax commu INFO error • Change the NC software version to
Undefined data was transferred from the NC. a compatible version.
IV - 70
Appendix 6. Alarms
6.1 List of Alarms

Alarm
Details Remedy
information
0011 Aux ax PCB err (Drive circuit) • Replace servo drive unit.
An error occurred in the drive unit's internal PCB.
0013 Aux ax S/W processing error • Replace servo drive unit.
An error occurred in the drive unit's internal reference
clock.
0015 Aux ax EEROM error • Replace servo drive unit.
A write error occurred to the EEROM in the drive unit.
0017 Aux ax PCB error(A/D err) • Replace servo drive unit.
An error occurred in the drive unit's internal A/D converter.
0018 Aux ax PCB error(LSI err) • Replace servo drive unit.
An error occurred in the drive unit's internal LSI.
0020 Aux ax detector error • Connect correctly.
An error occurred in the communication between the servo • Replace or repair cable.
drive unit and detector.
0024 Aux ax ground fault detection • Repair the ground fault section.
A ground fault of the output was detected when the power • Replace the cable or motor.
was turned ON.

Alarm
Details Remedy
information
0010 Aux ax under voltage • Review the power supply.
The power voltage is 160V or less. • Replace the servo drive unit.
0030 Aux ax regeneration error
The tolerable regeneration power of the internal • Set the parameter #50002 correctly.
regenerative resistor or external regenerative option was • Connect correctly.
exceeded. • Lower the positioning frequency.
• Change the regenerative option to
a larger capacity.
• Lower the load.
• Review the power supply.
Regenerative transistor error • Replace the servo drive unit.
0031 Aux ax overspeed • Increase the acceleration/

The motor's rotation speed exceeded the tolerable deceleration time constant.
momentary speed. • Review the gear ratio.
• Replace the detector.
0032 Aux ax overcurrent • Repair the wiring.

A current exceeding the servo drive unit's tolerable current • Replace the servo drive unit.
flowed. • Take countermeasures against
noise.
IV - 71
Appendix 6. Alarms
6.1 List of Alarms
Alarm
Details Remedy
information
0033 Aux ax overvoltage • Wire correctly.
The voltage of the converter in the servo drive unit was • Replace the servo drive unit.
400V or more. • For the internal regenerative
resistor, replace the drive unit.
• For the external regenerative option,
replace the regenerative option.
0046 Aux ax motor overheating • Reduce the motor load.
An operation state causing the motor to overheat • Review the operation pattern.
continued.
0050 Aux ax overload 1 • Reduce the motor load.
The servo drive unit or servomotor overload protection • Review the operation pattern.
function activated. • Change to a motor or drive unit
with large output.
• Change the setting of the
automatic tuning response
characteristics.
• Correct the connection.
• Replace the servomotor.
0051 Aux ax overload 2 • Review the operation pattern.

The max. output current flowed for several seconds due to • Change the setting of the
a machine collision or overload. automatic tuning response
characteristics.
• Correct the connection.
0052 Aux ax excessive error • Increase the acceleration/

A position deflection exceeding the excessive error deceleration time constant.
detection setting value occurred. • Increase the torque limit value.
• Review the power facility capacity.
• Review the operation pattern.
• Connect correctly.
• Repair or replace the cable.
IV - 72
Appendix 6. Alarms
6.1 List of Alarms
(4) Class: S52 Message: Aux ax servo warning

Alarm
Details Remedy
information
0092 Aux ax battery voltage drop • Mount a battery.
The absolute position detection battery voltage dropped. • Replace the battery and initialize
the absolute position.
00E0 Aux ax overregeneration warning • Lower the positioning frequency.
The regeneration power may have exceeded the tolerable • Change the regenerative option to
range of the built-in regenerative resistor or external a larger one.
regenerative option. • Lower the load.
00E1 Aux ax overload warning • Refer to the items for S03 0050.
The overload alarm 1 could occur.
00E3 Aux ax abs position counter warning • Take countermeasures against
There is an error in the absolute position detector internal noise.
data. • Replace the servomotor.
00E9 Aux ax main circuit OFF warning • Turn ON the main circuit power.
The servo ON signal was input while the main circuit
power was OFF.
The contactor operation is faulty.
(5) Class: Z70 Message: Aux ax abs position error

Alarm
Details Remedy
information
0001 Aux ax abs posn base set incomplete • Initialize the zero point (reference
The zero point (reference point) has not been initialized in point).
the absolute position system.
0002 Aux ax absolute position lost • Initialize the zero point (reference
The absolute position coordinate data in the drive unit has point).
been lost.
0003 Aux ax abs posn param changed • Correctly set the parameters and
The absolute position system related parameters have then initialize the zero point
been changed or lost. (reference point).
(6) Class: Z71 Message: Aux ax drop voltage

Alarm
Details Remedy
information
0001 Aux ax abs encoder: back up voltage drop • Check the battery and detector
The data in the detector has been lost. cable and then initialize the zero
Battery voltage drop. point (reference point).
Detector cable wire breakage or looseness.
IV - 73
Appendix 6. Alarms
6.1 List of Alarms
(7) Class: Z73 Message: Aux ax system warning

Alarm
Details Remedy
information
0001 Aux ax battery for abs data fault • Check the battery and detector
Battery voltage drop. cable. The zero point does not
Detector cable wire breakage or looseness. need to be initialized.
0003 Aux ax absolute position counter warning • Replace the detector.
An error occurred in the detector's absolute position
counter.
(8) Class: M00 Aux ax operation error

Alarm
Details Remedy
information
0001 Aux ax dog overrun • Lower the zero point return speed
When executing dog-type reference position, the zero or increase the dog length.
point return speed is too fast or the dog length is too short.
0003 Aux ax R-pnt direction illegal • Move the axis in the correct
When executing reference position return, the axis was direction.
moved in the opposite of the designated direction.
0004 Aux ax external interlock • Cancel the interlock signal
The axis interlock function is valid.
0005 Aux ax internal interlock • Cancel the servo OFF.
An interlock was established by the servo OFF function.
0007 Aux ax soft limit • Check the soft limit setting and
The soft limit was reached. machine position
0024 Aux ax R ret invld at abs alm • Initialize the absolute position
Reference position return was executed during an reference point and then fix the
absolute position alarm. absolute position coordinates.
0025 Aux ax R ret invld at ini • Initialize the absolute position
Reference position return was executed while initializing reference point and then fix the
the absolute position. absolute position coordinates.
IV - 74
Appendix 6. Alarms
6.1 List of Alarms
(9) Class: M01 Aux ax operation error

Alarm
Details Remedy
information
0101 Aux ax no operation mode • Correctly designate the operation
The operation mode is not designated, or the operation mode.
mode was changed during axis movement.
0103 Aux ax feedrate 0 • Set a value other than zero in the
The operation parameter's feedrate setting is zero. feedrate setting or override value.
The operation parameter feedrate setting is zero.
Or, the override is valid, and the override value is zero.
0160 Aux ax sta No. illegal • Correctly designate the station No.
A station No. exceeding the No. of indexed divisions was
designated.
0161 Aux ax R-pnt ret incomplete • Execute the reference position
Automatic/manual operation was started before reference return.
position return was executed with the incremental system.
0162 Aux abs position initializing • Complete the absolute position
The start signal was input while initializing the absolute reference point initialization.
position reference point.
0163 Aux ax abs position error • Initialize the absolute position
The start signal was input during an absolute position reference point and then fix the
alarm. absolute position coordinates.
0164 Aux ax arbitrary positioning • Turn the random positioning mode
The manual operation mode was started during the OFF before switching to the
random positioning mode. manual operation mode.
0165 Aux uneven index sta No. ilgl • Check the commanded station No.
The commanded station No. was higher than 9 or the and the parameter "#50100 station"
number of indexing stations during uneven indexing. setting.
IV - 75
Appendix 6. Alarms
6.1 List of Alarms
(10) Class: Y02 Auxiliary axis MCP alarms

An error occurred during data transfer between the MCP and auxiliary axis drive unit after turning on the
power.
0050 Aux ax sys alm: Proc time over The software or hardware may be damaged.
0051 0000 Aux ax commu er:CRC error 1 A communication error has occurred between the
(10 times/910.2ms) controller and drive unit.
0001 Aux ax commu er:CRC error 2 • Take measures against noise.
(2 continuous times) • Check that the communication cable connector
between the controller and drive unit and one
0002 Aux ax commu er:Recv timing between the drive unit are tight.
(2 continuous times) • Check whether the communication cable
xx03 Aux ax commu er:Data ID between the controller and drive unit and one
(2 continuous times) between the drive units are disconnected.
xx: Axis No. • A driving drive unit may be faulty. Take a note of
xx04 Aux ax commu er:Recv frame no. the 7-segment LED contents of each driving
(2 continuous times) drive unit and report to the Service Center.
xx: Axis No.
(11) Class: Y03 Message: Aux ax drive unit unequipped

The drive unit is not properly connected.
Axis No. bit correspondence (bit 0: 1st axis, bit 1: 2nd axis, Check the auxiliary axis drive unit mounting
1 to 4 bit 2: 3rd axis, bit 3: 4th axis) state.
• Check the end of the cable wiring.
• Check the cable for broken wires.
• Check the connector insertion.
The auxiliary axis drive unit input power is not
being input.
The auxiliary axis drive unit axis No. switch is
illegal.
IV - 76
Appendix 6. Alarms
6.1 List of Alarms
6.1.10 Computer Link Errors

LUU Message {
Error No.
Message
Alarm class
(1) Class: L01 Computer link error

Error
Details Remedy
No.
-2 Serial port being used • Check whether the same port being used by
Serial port has already being opened or Anshin-net, etc.
cannot be used. • Recheck the parameters for tape operation port.
-4 Timeout error • Set a greater timeout value in the input/output
Communication ends with timeout device parameter.
CNC has a 248-byte receive buffer. • Recheck the HOST software as to whether or not
The time during which CNC receives 248 the HOST transmits data in response to DC1
bytes exceeds the "TIME-OUT" value set in from CNC (data request).
the I/O device parameter. • Check whether or not start code of computer link
parameter is set to 0.
-10 Host ER signal OFF • Check whether or not the cable is disconnected
HOST ER (CNC DR) signal is not turned ON. from the connector.
• Check whether or not the cable is broken.
• Check whether or not the HOST power is turned
ON.
-15 Parity H error • Recheck the HOST software as to whether or not
Communication ends with parity H. the data to be transmitted to CNC is ISO code.
-16 Parity V error • Recheck the data to be transmitted to CNC.
Communication ends with parity V.
-17 Overrun error • Recheck the software as to whether or not the
Although CNC transmits DC3 (request to stop HOST stops transmitting data within 10 bytes
data transfer) to the HOST, it receives data of after receiving DC3.
10 bytes or more from the HOST, thus • Recheck the HOST software as to whether or not
terminates communication. the HOST transmits data such as a command or
When CNC is transmitting data to the HOST, it header to CNC during receiving a work program.
receives data of 10 bytes or more from the
HOST.
IV - 77
Appendix 6. Alarms
6.1 List of Alarms
6.1.11 User PLC Alarms

UUU Message {{{{ {{{{
Sub-status 2
Sub-status 1
Message
Alarm class
Sub-status
1 2
U01 - - PLC program is not input. Download the PLC program of the
No user (Note) Emergency stop (EMG) will format selected with the PLC
PLC be applied. environment selection parameters
(bit selection #51/bit 4).
U10 0x0010 - PLC scan time error Edit the PLC program size to a
Illegal PLC The scan time is 1 second or smaller size.
longer.
0x0040 - PLC program operation mode Download the PLC program
illegal having the same format as when
PLC program different from the the power was reset or turned
designated mode was ON.
downloaded.
(Note) Emergency stop (EMG) will
be applied.
0x0080 - GPPW ladder code error Download the correct GPPW
(Note) Emergency stop (EMG) will format PLC program.
be applied.
0x008x - PLC4B ladder code error Download the correct PLC4B
An illegal circuit was found in the format PLC program.
PLC4B ladder.
bit1: PC medium-speed circuit
illegal
bit2: PC high-speed circuit illegal
be applied.
0x0400 Number of Software illegal interrupt Turn the power ON again.
ladder The PLC program process stopped If the error is not reset, download
steps abnormally due to an illegal the correct PLC program.
software command code.
be applied.
IV - 78
Appendix 6. Alarms
6.1 List of Alarms
Sub-status
1 2
U10 0x800x Number of Software exception
Illegal PLC PLC The PLC program process stopped
program abnormally due to a bus error, etc.
steps bit 0: BIN command operation error Refer to the methods for using the
bit 1: BCD command operation BCD and BIN function
error commands.
bit6: CALL/CALLS/RET Turn the power ON again.
command error If the error is not reset, download
bit7: IRET command execution the correct PLC program.
error
(Note) Emergency stop (EMG) is
applied for bit 6/7.
U50 The PLC program is stopped. Start the PLC program.
PLC
stopped
U55 The PLC program is stopped and not Write the PLC program into ROM.
PLC written into ROM.
stopped /
is not
saved
U60 The PLC program is not written into Write the PLC program into ROM.
Ladder is ROM.
not saved
(Note) The number of PLC program steps displayed on the screen may not match the actual number of error
occurrence steps because of the PLC program timing. Use this as a guideline of the occurrence
place.
IV - 79
Appendix 6. Alarms
6.1 List of Alarms
6.1.12 Network Service Errors

N001 • There is an error in the modem • Check the connection between the NC and
Modem initial connection when the power is turned modem, connection port and modem power.
error ON.
N002 • The dial transmission failed more than • Wait a while, and then transmit again.
Redial over the designated No. of redial times.
N003 • The phone line is not connected. • Check the modem’s phone line connection.
TEL unconnect
N004 • An error other than the above errors • Note down the circumstances under which
Net occurred during communication. this error occurred, and contact the Service
communication Center.
error
N005 • The modem connection port is being • Quit using the modem connection port with
Invalid net used for another function such as the other function, and then turn the power
communication input/output. ON again.
• The modem connection port settings • Check the modem connection port settings.
are incorrect.
N006 • The diagnosis data file has been • Erase the message.
Received result received
of diagnosis
N007 • A file larger than Anshin-net server • Reduce the size of machining program file
Send data size capacity (64Kbyte) has been so that it won't exceed the capacity of
over transmitted during machining data Anshin-net server.
sharing.
N008 • When machining data sharing function • Before receiving file, confirm that a
No file on server is being executed, file reception machining program file exists on Anshin-net
fails, as the file does not exist on server.
Anshin-net server.
N009 • File reception fails due to wrong • Input the password again.
Password error password when machining data
sharing is being executed.
N010 • Data reception fails due to wrong • Input the customer number again.
Customer customer number when machining
number error data sharing is being executed.
N011 • As the size of file to be received is • Ensure sufficient free space on the NC side.
Storage capacity bigger than free space on the NC side,
over file reception fails during machining
data sharing.
N012 • A file on Anshin-net server cannot be • Check if the file exists on Anshin-net server.
File deletion error deleted when machining data sharing • Note down the circumstances under which
is being executed. this error occurred, and contact the Service
Center.
IV - 80
Appendix 6. Alarms
6.2 Operation Messages

The following messages display on each screen.
6.2.1 Search-related Operation Messages

Message Details
Searching • The operation search is being executed.
Search completed • The operation search was completed correctly.
Verifying • The program is being verified.

Verifying stopped • The program verification stopped.
Search error • Could not find the designated ONB number.
Review the ONB number or machining program settings.
• The operation search could not be completed correctly.
• When the parameter (#9005) of the tape mode port was set out of the
range or when the port was not connected, an operation search of
NC serial was performed.
• The T code list search failed. Review the program name.
• Could not find the machining program in HD or IC card.
• Check the parameters for HD operation or IC card operation.
• Tape search was executed during the HOST LINK communication.
Setting error • The directory name exceeded the display range.
A directory path for which the entire directory cannot be displayed
cannot be designated in the directory name area.
• The search is not possible because ONB number is not designated.
Restart search is completed • The restart search was completed.

Executing restart search • The restart search is being executed.
Execute operation search • The program is not searched.
Execute the operation search.
Can't cancel verify stop • The compare stop cannot be canceled because the operation is not
in a compare stop.
Executing top search • The top search is being executed correctly.
Top search completed • The top search was completed correctly.
Top search not completed • The restart search (type 2) was executed without the top search.
Can't input data • Data input was attempted during M, S, T, B history display.
Input some of ONB • Awaiting ONB number input
Verifying stop posn already • The verify stop position has already been registered.
registered
No searched program • The program has not been searched.
Program restarting • The program is being restarted.
Program error • The restart search was executed in the program with an error.
N/B block not found • The restart search was executed, designating N or B No. not exist.
Restart search interrupted by • Reset was executed during the restart search.
reset
No. of repetitions exceeded • The restart search was executed, designating the number of
repetitions exceeding the number set in the program.
Program not found • The restart search was executed, designating a program No. not
exist.
IV - 81
Appendix 6. Alarms
6.2.2 Graphic Display-related Operation Messages

Message Details
Searching • The check search is being executed.
Search error • Could not find the designated ONB number.

Review the ONB number or machining program settings.
• The check search could not be completed correctly.
• When the parameter (#9005) of the tape mode port was set out of the
range or when the port was not connected, an operation search of
NC serial was performed.
Executing automatic operation • An attempt was made to perform operations such as parameter, tool
compensation amount data and coordinate system offset settings
during auto operation. (Input/output also possible during auto
operation)
• The machining program and MDI data that the operator is attempting
to edit cannot be edited during auto operation.
• It is not possible to be executed a check search or check start-up
during auto operation.
• An attempt was made to set the verify stop position during auto
operation.
Setting error • The directory name exceeded the display range.
A directory path for which the entire directory cannot be displayed
cannot be designated in the directory name area.
• The check search is not possible because ONB number is not
designated.
• A non-existent axis name or setting that does not exist in the format
was made when making the display mode settings.
Set using an existing axis name.
• Incorrect tool No. was specified at the execution of tool clear.
Execute operation search • The program is not searched.

Execute the operation search.
Checking • The program check is being executed.
Check stopped • The program check is being stopped.
Work form is illegal • A workpiece is not drawn correctly because the two or more
workpiece widths are set to "0".
Push [Check reset] menu • An error occurred in the graphic check.
Press the [Check reset] menu key to reset the error.
Executing trace • The trace mode is valid.
Program check completed • The trace in the program check completed with an M02/M30 code.
Reset complete • The program check was reset.
Tool interfere with work • The tool contacted the workpiece when performing rapid traverse
(G0) movement with the interference check enabled.
Program checking • The program check is being executed.
Executing reset operation • The program check is being reset.
Executing trace(tip posn) • The tip position trace mode is valid.
Executing BG simulation • The back ground simulation is being executed.
Draw library inside error (n) • Contact the service center.
IV - 82
Appendix 6. Alarms
Message Details
Program check not possible • Graphic check was attempted during the Computer link B operation.
Execute check search • The program check is disabled. Execute the check search.
Solid check disabled (memory • The 3D program check is disabled due to the memory shortage.
shortage) Separate the programs and execute the check drawing again.
Press the menu [Work init] once before performing the check
drawing again.
6.2.3 Variable (Common variables, local variables) - related Operation Messages

Message Details
Erase? (Y/N) • Message to confirm the line erase.
[Y] or [INPUT] : Variables are deleted.
[N] : Variables are not deleted.
6.2.4 PLC Switch-related Operation Messages

Message Details
Set up parameter ?(Y/N) • Message to confirm the parameter setup.
[Y] or [INPUT] : It will be possible to make settings.
[N] : It will not be possible to make settings.
6.2.5 Compensation-related (Tool compensation, coordinate system offset) Operation

Messages
Message Details
Erase? (Y/N) • Message to confirm the erasing.
[Y] or [INPUT] : Erase the data.
[N] : Do not erase the data.
Clear all axes? (Y/N) • Message to confirm the all axes clear.
[Y] or [INPUT] : Clear the data for all axes.
[N] : Do not clear the data.
Cannot return to origin • Operations other than line paste, paste and data input cannot be
undone.
• It is the initial state. Cannot undo.
• The last operation was performed in another part system. Cannot
undo the operation.
Clear all? (Y/N) • Message to confirm the clearing the all data.
[Y] or [INPUT] : Clear all data.
[N] : Do not clear the data.
Input P number • The coordinate system [Coord G54.1 P] menu was pressed.
• The expansion workpiece coordinate system P No. was input.
Data clear complete • Clearing of the collection data is complete.

Execute the collection data • Determines whether to clear the collection data. Press [Y] or [INPUT]
clear? to clear the data.
IV - 83
Appendix 6. Alarms
6.2.6 Data Input/Output-related Operation Messages

Message Details
Overwrite this file?(Y/N) • Message to confirm the overwriting.
[Y] or [INPUT] : Overwrite the file.
[N] : Do not overwrite the file.
Over run error • The buffer overran or overflowed.
Memory over • The program cannot be written, because the memory capacity will be
exceeded.
Edit lock B • It is not possible to change machining program B (8000 to 8999: user
standard subprogram) or machining program C (9000 to 9999:
machine tool builder custom program) as edit lock B is enabled.
Edit lock C • It is not possible to change machining program C (9000 to 9999:
machine tool builder custom program) as edit lock C is enabled.
Can't make directory on this • Creation of a directory was attempted for a device that cannot have a
device directory.
Designated file does not exist • The file specified in device A, and B does not exist.
• The applicable file does not exist in the specified directory.
The file name is a directory • A directory was designated for the file transfer. A directory cannot be
transferred.
Change complete • The data conversion completed correctly.
Changing • The data is being converted.
Erase complete • The file has been erased.
Erase ended. Some file not • The file erasing completed, but there are some files that could not be
erased erased.
Verify error • An error occurred when performing a file verification.
Compare error. Compare next • Message to confirm the comparison
file?(Y/N) [Y] or [INPUT] : Compare the next file.
[N] : Do not compare the next file.
Compare complete • The data comparison completed.
Verifying • The data is being compared.
The file already exists • The input file name already exists.
• The file name after renaming already exists.
Can't erase designated file • Erasing was attempted of a file that cannot be erased.
Can't rename designated file • An attempt was made to change the name of a file that cannot be
renamed.
Can't condense designated file • Condensing of a file that cannot be condensed was attempted.
Designated file is locked • Changing was attempted of a locked file.
Can't open file for dev A • Could not find the file for device A.
Or, the file is in a state in which it cannot be accessed.
Can't open file for dev B • Could not find the file for device B.
Or, the file is in a state in which it cannot be accessed.
Can't read file for dev A • Could not read in the file for device A.
Recheck the connection status for device A or the input/output
parameter setting.
Can't read file for dev B • Could not read in the file for device B.
Recheck the connection status for device B or the input/output
parameter setting.
IV - 84
Appendix 6. Alarms
Message Details
Can't close file for dev A • Contact the service center
Can't close file for dev B • Contact the service center.

Can't write file for dev A • Could not write in the file for device B.
Recheck the connection status for device A or the input/output
parameter setting.
Can't write file for dev B • Could not write in the file for device B.
Recheck the connection status for device B or the input/output
parameter setting.
Can't seek file for dev A • Contact the service center.
Can't seek file for dev B • Contact the service center.
File name not designated for dev • A file name was not designated for device A.
A
File name not designated for dev • A file name was not designated for device B.
B
Can't open directory for dev A • Could not find a directory corresponding to device A.
Can't open directory for dev B • Could not find a directory corresponding to device B.
Different devices designated in A • The same device must be designated for devices A and B, but
and B differing devices were designated.
Timeout error • A timeout error occurred when communicating with the external
device.
Checking • Cannot be executed during a check
Make directory complete • Creation of the directory has been completed.
Dir create Complete • Creation of the directory has been completed.

Can't make directory • An error occurred while creating the directory.
The directory is not empty • A filewas found in the directory.
Erase the file in the directory.
Directory pass is illegal • The designated directory path name is illegal.
Input a correct directory path name.
Data protect • Setting, erasing, parameter setting, etc., of the various data is
prohibited, because the data protect key is validated.
Transfer complete • The data transfer completed correctly.
Transferring • The data is being transferred.
Parity H error • A parity H error was detected.
Parity V error • A parity V error was detected.
File entry over • The No. of registration files designated in the specifications was
exceeded, so the file could not be registered.
Program No. not found in the file • There is no program number in the selected file.
Executing format • The formatting is being executed.
Format complete • The formatting completed.
Format error • The formatting failed.
Framing error • An error occurred between the NC and the external device.
Variable conversion error • An error occurred during the M2 macro conversion, and the
conversion failed.
IV - 85
Appendix 6. Alarms
Message Details
Merge complete • The data merge completed.
Merge execution • The data merge is being executed.
Memory alloc error • Securing of the communication data range failed.
Rename complete • The rename has been completed.
• Message to confirm the operation.
OK? (Y/N)
[Y] or [INPUT] : Execute the operation
[N] : Cancel the operation.
I/O not ready • An error occurred between the NC and the external device.
I/O parameter error • The external device settings and input/output parameters do not
match.
I/O port busy • Input/output was not possible as the I/O port is busy.
FD write protect • The FD is write-protected.
Release the write protection.
PLC running • An attempt was made to input a user PLC during PLC RUN.
• Stop the PLC on the maintenance screen.
FD not ready • An attempt was made to perform an FD operation search with no FD.
• An attempt was made to display the FD list with no FD.
MemoryCard not ready • An attempt was made to perform operations with no memory card.
DS not ready • An attempt was made to perform operations with no data server.
Can't write in READ-ONLY file • Contact the service center.
Condense complete • Condensing has been completed.
A directory does not exist • The specified directory does not exist.
Setting complete normally • Decryption code setting file of the credit system was set normally.
IV - 86
Appendix 6. Alarms
6.2.7 Parameter-related Operation Messages

Message Details
Designate copy end posn • The copy start position was specified using the cursor. Continue and
specify the copy end position using the cursor.
Copy start posn and end posn • When the copy range was designated, a position before the start
reversed position was designated as the end position.
Columns of copy start and end • A different column (axis or part system) was specified for the copy
different start/end position at the screen with the arrangement configuration
for each axis and part system.
Copy range is inadequate • Could not find the parameter No. for the copy start position.
• A value larger than the last parameter No. was designated as the
copy end position parameter No.
Check the designated copy range.
Setting error • The port is already being used.
• The parameter HOST LINK was turned ON during the Anshin-net
communication.
Setting error: column n • The nth column setting data is inappropriate when multiple axes were
set at the same time (/ division). (Settings have been made up to the
(n-1)th column.)
Password is illegal • The password designated for displaying the Machine
Parameter screen is illegal.
Input the password • The menu key for first displaying the Machine Parameter
screen was pressed after the power was turned ON.
Paste error • An attempt was made to paste in a different parameter from the copy
parameter.
Paste? (Y/N) • Message to confirm the operation when pasting.
[Y] or [INPUT] : Paste the data at the current cursor position.
[N] : Do not paste the data.
Data protect • Setting, erasing, parameter settings, etc., of the various data is
prohibit, because the data protect key is validated.
Executing automatic operation • An attempt was made to make parameter settings during auto
operation.
Can't select • The password designated for displaying the machine parameters has
not been input.
• Display of the machine parameters was attempted on the [Param
No.] menu, but the password has not been input.
Press the [Machine param] menu, and input the password for
displaying the machine parameters.
No odd number for R register • An odd number cannot be used for R register start No.
start No. Use an even number.
IV - 87
Appendix 6. Alarms
6.2.8 Measurement-related (Workpiece, rotation) Operation Messages

Message Details
TLM switch OFF • Measurement, retrieving of the skip position, writing the coordinates
data etc. was attempted when the TLM switch was OFF.
Can't take-in skip posn •Could not retrieve the skip position.
Check the following:
< When measuring the workpiece >
1. Is the name of the axis to be measured designated in the basic axis
(I, J, K)?
2. Is the axis that executed the axis movement a measurement axis?
< When measuring the rotation >
1. Is the name of the axis to be measured designated in the coordinate
rotation plane (horizontal axis, vertical axis)?
2. Is the axis that executed the axis movement a measurement axis?
Can't write coordinates data • Could not obtain the measured axis No.
• The measured angle was illegal.
• Could not write into the coordinate system offset.
Measure again.
• The work coordinate offset data was attempted to set when the
measurement counter does not have the necessary values.
• The work coordinate offset date was attempted to set in the slave
axis.
Sensor take in not possible • Could not retrieve the position measured with the touch sensor.
Measure again.
Can't measure • Measurement failed.
Sensor signal was illegally • The sensor signal was already ON when the tool measurement mode
turned on (TLM) signal was validated.
• The sensor signal turned ON when there was no axis movement after
the tool measurement mode (TLM) signal was validated.
• The sensor signal turned ON at a position within 100µm from the final
entry start position.
• Move the axis in a safe direction after turning the sensor signal OFF
or turning the tool measurement mode signal OFF.
Can't write compensation data • The cursor position and the cell for writing the compensation amount
(length dimension, radius dimension) do not match.
Match the cursor position with the cell for writing the compensation
amount.
Offset No. not found • During manual tool length measurement, the sensor was turned ON
designating tool compensation No. not exist.
• During manual tool length measurement, the measurement method
was switched to manual tool length measurement 2 designating tool
compensation No. not exist.
• Correctly set the R register of compensation No.
TLM axis is illegal • During 2 or more axes movement, the tool length measurement was
executed by turning the sensor ON. Keep the tool away from the
sensor and execute the measurement by one axis.
TLM axis not returned to ref. • The tool length measurement was executed by tuning the sensor ON
position for the axis in which dog-type reference point return has not been
executed. Carry out reference point return for the measurement axis.
Can't write rotation parameter • The measured result cannot be set in the process parameter.
IV - 88
Appendix 6. Alarms
Message Details
Can't calculate center & angle for • Three points necessary for calculation are not retrieved.
rot • Center shift amount or censor radius was failed to retrieve.
• Calculation of the center and the angle was failed.
Input 0 to coord center & angle • The center and the angle are not "0".
for rot Set "0" in the parameter "#8623 Coord rot centr (H)", "#8624 Coord
rot centr (V)" and "#8627 Coord rot angle".
Can't calculate • Hole center cannot be determined.
Meas axis not returned to ref. • The workpiece measurement was executed when dog-type reference
position point return has not been executed. Carry out reference point return
for the measurement axis.
6.2.9 Tool (Tool registration, tool life) -related Operation Messages

Message Details
Designated group already exists • An already existing group No. was designated when changing the
group No. (Tool life screen (grp))
• An already existing group No. was designated when newly creating
the group. (Tool life screen (grp list))
Designate a group No. that does not already exist.
Designated group does not exist • Erasing was attempted on the Tool life screen (grp list) of a group that
does not exist.
Can't register group • The group registration process on the Tool life screen (grp list) failed.
Can't delete group • The group deletion process on the Tool life screen (grp list) failed.
Erase? (Y/N) • Message to confirm the erasing.
[Y] or [INPUT] : Erase the data
Delete all groups? (Y/N) • Message to confirm the erasing of all groups.
[Y] or [INPUT] : Erase all groups
[N] : Do not erase all groups.
Can't delete all groups • All groups' deletion cannot be executed because data protection key
(KEY 1) is validated or automatic operation mode is validated, etc.
during all groups' deletion. All groups' deletion cannot be executed
because nothing has been registered to group, also.
Pot number not exist • The set pot number does not exist.
Check the pot number.
Create new file? (Y/N) • Message to confirm the operation when newly creating data, files,
etc.
[Y] or [INPUT] : Newly create.
[N] : Cancel the operation.
Input the tool number • Waiting tool number input.
Clear not possible • The clear range is incorrect.
Spindle/stndby tool display not • The spindle standby cannot be displayed due to the user PLC setting.
possible Contact the machine tool builder.
Format tool life data? (Y/N) • Determines whether to format the tool life management data. When
[Y] is input, the formatting is executed.
Tool life format complete • The tool life management data formatting completed.
IV - 89
Appendix 6. Alarms
Message Details
Exists in spindle/standby. Set? • An attempt was made to set the same No. as the tool No. for
(Y/N) spindle/standby.
Exists in magazine 1. Set? (Y/N) • An attempt was made to set the same No. as the tool No. that has
been registered to the valid magazine.
IV - 90
Appendix 6. Alarms
6.2.10 Editing-related Operation Messages

Message Details
Buffer correct not possible • Buffer correction cannot be performed for this program.
• Buffer correction was attempted during the BTR operation.
Can't write into file • Could not write the data to the memory with the buffer correction.
Overwrite this file?(Y/N) • Message to confirm when registering MDI
[Y] or [INPUT] : Overwrite the file.
[N] : Do not overwrite the file.
Memory over • The program cannot be written, because the memory capacity will be
exceeded.
Designated character string not • Could not find the search results and character string in the program.
found
Save current file ?(Y/N) • Message to confirm the saving.
[Y] : Save the changes to the current file.
[N] : Do not save the changes to the current file.
A file does not exist • An attempt was made to select and edit a non-existent file.
Executing • Following menu's process is executing now:
"Line paste", "Line clear", "Undo", "String search", "String replace",
"Miss warning", or "Next miss".
Designated file does not exist • An attempt was made to select and erase a non-existent file.
Erase complete • The data erasing completed.
Can't erase designated file • The selected file cannot currently be erased.
Designated file does not exist • A file that does not exist was designated when file editing.
Designated file already exists • When creating a new file, a file name was designated that already
exists.
Replace? (Y/N) • Message to confirm the character string replacement.
[Y] or [INPUT] : Replace the character string.
[N] : Do not replace the character string.
File access error • Contact the Service Center.
File open error • The designated file is already open.
Editing • A program is being edited on the screen.
Save the program to write it into the memory.
Program entry over • The program could not be registered in the memory when attempted,
because the No. of registrations designated in the specifications
would be exceeded.
Block char nos over • The character number limitation in one block was exceeded.
Paste error • Pasting was attempted within the copy range of the same file.
Copy range is inadequate • The copy range designation is inadequate.
Check whether the designated range exists.
• The range was designated exceeding 100 lines during mass editing.
Area designation is inadequate • The area designation is inadequate.
Check whether the designated area exists.
Designated line is out of • Designation was attempted of a line No. larger than the No. of lines in
program range the entire program.
IV - 91
Appendix 6. Alarms
Message Details
MDI no setting • Editing of the MDI was started, but the MDI setting was incomplete.
Abs/Inc mode is illegal • During playback editing:
G90 was set when control parameter "Playback G90" was OFF.
G91 was set when control parameter "Playback G90" was ON.
MDI search complete • The MDI search completed.
Can't search in MDI mode • The restart search was attempted during MDI mode.
• Execute the restart search after switching other than MDI mode.
MDI Set ended • MDI setting cannot be executed.
MDI Setting error • MDI setting was completed.
MDI search error • Could not execute the MDI search.
MDI entry complete • MDI entry has been completed.
Can't edit except in MDI mode • "#1144 mdlkof" (MDI setting lock) is "0" and therefore it is not possible
to edit the MDI program in a mode other than MDI mode.
Input miss was detected • An input miss was detected.
Input miss was not detected • A search was performed for an input miss, however, none was found.
Can't edit a file except in NC • Editing cannot be performed at the edit window for programs other
memory than those in the NC memory.
Save it • The cursor was tried to move beyond the editable range during
mass-editing. Save, then operate again.
Save not possible • A special file (history file etc.) that cannot be saved was edited and an
attempt was made to save it. Perform an operation to quit editing.
• Failed saving due to file size over, etc. during mass-editing.
• Setting of "#1166 fixpro" was illegal. Use the settings for a regular
program.
• MDI cannot be entered due to MDI editing mode. Press INPUT key
and finish editing.
Save left side file? (Y/N) • Message to confirm whether saving the left side file of the
multi-program display type
[Y]: Save the change
[N]: Do not save the change
Save right side file? • Message to confirm whether saving the right side file of the
(Y/N) multi-program display type
[Y]: Save the change
[N]: Do not save the change
Can't edit because of size over • The program cannot be written, because the memory capacity will be
exceeded.
• If the memory capacity of the transfer designation device is exceeded
during the automatic backup, increase the available memory of the
device.
Can't edit the searched file • The serial file cannot be edited.
DS not ready • Operation was attempted when a DS was not inserted.
• Creating or opening a program was attempted when a DS was not
inserted.
FD not ready • The FD operation search was attempted when an FD was not
inserted.
• The FD list display was attempted when an FD was not inserted.
• Creating or opening a program was attempted when an FD was not
inserted.
IV - 92
Appendix 6. Alarms
Message Details
MemoryCard not ready • Operation was attempted when a memory card was not inserted.
This cannot be specified • Invalid special characters (/E, etc.) were set.
Loading • Loading file.
Saving • Saving file.
Can't execute playback edit • The playback editing cannot be executed because the right side
area is mass-editing mode.
• Playback editing was attempted while program file to be edited is not
designated. Display a program file in the right side area.
Program display lock C • The program display or search cannot be executed. Review the
parameter "#1121 pglk_c" (program display lock).
6.2.11 Diagnosis-related Operation Messages

Message Details
Erase? (Y/N) • Message to confirm alarm history clear operation
[Y] or [INPUT] : Erase the data
Can't write data • The data cannot be written.
Device is illegal • The designated device is inadequate.
Modal output not possible • The modal output process failed.
Modal clear not possible • The modal cancel process failed.
Continue display not possible • Continuous display is not possible because data is not set at the
cursor position.
One-shot output not possible • The one-shot output process failed.
Setting data not found • The data has not been set.
Select a menu • A device No. was set without selecting a menu operation.
Press any operation menu and input the device No. with a menu
highlighted.
IV - 93
Appendix 6. Alarms
6.2.12 Maintenance-related Operation Messages

Message Details
Password is illegal • The input password is incorrect.
Input password • The [Password] menu key was pressed, and the password input
mode was entered.
Input a password.
Now making back-up • Currently backing up system data and the user PLC program to a
specified device.
Backupping • The SRAM data is being backed up on the HD.
Backup complete • Backup of the SRAM data on the HD has been completed.
• Back up of system data and user PLC program to a specified device
has been completed.
Backup error • An error occurred while backing up the SRAM data on the HD.
Select directory to backup • Select area by moving cursor, using ↑ and ↓ keys.
Press the "INPUT" key to confirm.
Select directory to restore • Select file by moving cursor, using ↑ and ↓ keys.
Press the "INPUT" key to confirm.
Executing format • The formatting is being executed correctly.
Format complete • The formatting completed correctly.
Format error • The NC memory formatting failed.
Contact the nearest service center.
Quit HMI ?(Y/N) • Message to confirm the HMI quitting
[Y] or [INPUT] : Quit the HMI.
[N] : Do not quit the HMI.
Format NC memory?(Y/N) • Message to confirm the NC memory formatting
[Y] or [INPUT] : Start formatting the NC memory.
[N] : Do not format the NC memory.
Execute SRAM backup ?(Y/N) • Message to confirm the SRAM back up
[Y] or [INPUT] : The SRAM data is backed up to the HD.
[N] : The SRAM data is not backed up to the HD.
PLC running. Does it stop? (Y/N) • Message to confirm the PLC STOP
[Y] or [INPUT] : Backup the SRAM data on the HD.
[N] : Do not backup the SRAM data on the HD.
Restoring • The system data and user PLC program are now being restored to
the NC from a specified device.
Restore complete • Restoration of system data and user PLC program to the NC from a
specified device has been completed.
Auto adjust error • The H/W status cannot be read properly, and therefore it is not
possible to perform auto adjustments.
Check the remote I/O unit.
Perform manual adjustments.
• The unit is defective. Replace the unit.
Change Ope. test mode • Operation of the Operation test screen was attempted when the
operation adjustment mode was not selected.
Test mode sig valid signal is now • The operation adjustment mode cannot be selected because the
OFF operation adjustment mode valid signal (R9998/bit0) is 0.
IV - 94
Appendix 6. Alarms
Message Details
Auto adjust complete • Analog output adjustment completed normally.
Auto adjust execution • Performing analog output adjustment normally.
Execute? (Y/N) • Message to confirm the operation
[Y] or [INPUT] : The currently selected operation is performed.
[N] : The currently selected operation is not performed.
Unit not equipped • The machine is not equipped with an analog output unit.
A serial number is inaccurate • The system data to be restored and the serial number in the NC do
not match, and therefore it is not possible to restore.
• Check to ensure that the serial number in the NC has been set and
that the system data to be restored matches.
Operating aux axis • It is not possible to set parameter and input/output data during
auxiliary axis operation.
• It is not possible to change the display axis during auxiliary axis
operation.
IV - 95
Appendix 6. Alarms
6.2.13 Data Sampling-related Operation Messages

Message Details
Executing sampling • The waveform data is being sampled.
Input the axis name • This appears when the data type is selected in the Ch1 or Ch2 data
setting area.
Input the name of the axis to be sampled.
Input axis name/signal No./bit • This appears when the data type is selected in the Ch1 or Ch2 data
setting area.
Set the sampling conditions common for Ch1 and Ch2.
Input device name/device No. • Input device name/device No.
Input file/sub-ID/item/data • This appears when an NC file is selected in the Ch1 or Ch2 data
setting area.
Change the area • Change the area.
Sampling conditions are illegal • The data cannot be sampled as the setting conditions are illegal.
Review the data, vertical scale, sampling rate and horizontal scale on
the Condition setting screen.
Can't start sampling • "#1224 aux08/bit0" is "0" and sampling start-up cannot be performed.
The collection invalid • The parameters are set to prevent data being collected. Check the
parameters.
The collection begin? • Determines whether to start data collection. Press [Y] or [INPUT] to
start data collection.
The collection stop? • Determines whether to stop data collection. Press [Y] or [INPUT] to
stop data collection.
The collection is being executed • An attempt was made to start data collection while data collection
was being performed.
The collection is stopping • An attempt was made to stop data collection while data collection was
stopped.
The collection invalid • The data collection is set invalid in the parameter. Check the
parameter.
Scroll execution • The waveform display is being scrolled.
Refresh execution • The waveform is being refreshed.
IV - 96
Appendix 6. Alarms
6.2.14 Absolute Position Detection-related Operation Messages

Message Details
Setting absolute position set • Setting from the screen was attempted of absolute position detection
data when the "Absolute Position Set" was not ON.
Press the menu key [Absolute Position Set] to turn it ON.
Not the abs position detection • An absolute position detection system has not been selected for the
system currently selected axis.
The machine parameter (Axis specification parameter "#2049 type")
must be set.
Axis name inappropriate • The set axis name is inappropriate. Check the axis name.
Not passed on grid • The absolute position basic point was set without passing the grid
after the power ON in the dogless-type absolute position detection.
Return one grid back and repeat the procedure.
Can't start • Settings of "#0 absolute posn set", "#2 Z-point" and "#2055 pushf" are
not adequate.
• "AbsEncoder: Serial data error" alarm (Z71 0005) has occurred.
Check the parameter and the alarm.
Illegal direction • JOG starting direction is illegal in the machine end stopper method of
the dogless-type absolute position detection.
6.2.15 System Setup-related Operation Messages

Message Details
Initial parameter creating • The initial parameter is being created.
Initial parameter transferring • The initial parameter is being transferred.
Spindle initial parameter • The spindle initial parameter is being transferred.
transferring
Can't write data • The data cannot be written.
• Setting of the initial parameter failed.
• Contact the service center.
Param set ended. • After completing the parameter setting, it determines whether
Format NC memory? (Y/N) executing the file format or not.
Enter [Y] or [INPUT] to execute the file format.
Write sample ladder? (Y/N) • It determines whether executing writing the sample PLC program or
not. Enter [Y] or [INPUT] to start writing the sample PLC program.
Sample ladder not found • The file to set the sample PLC program is lost.
IV - 97
Appendix 6. Alarms
6.2.16 Automatic Backup-related Operation Messages

Message Details
Auto backup disabled • Set a correct value in the device No. of the automatic backup device.
(Device illegal)
Auto backup disabled (No DS) • When turning ON the power next time, insert DS.
Auto backup disabled • When turning ON the power next time, insert the memory card.
(No memory card)
Auto backup proceeding • Wait for the automatic backup to complete.
Auto backup completed • The automatic back up is completed.
Memory over • The memory capacity of the transfer designation device was
exceeded during the automatic backup. Increase the available
memory of the transfer designation device.
File access error • A file access error occurred during the automatic backup. Contact
the service center.
Can't make directory • The storage destination directory of the automatic backup data
described in the custom definition file does not exist. Create the
directory of the storage destination.
Write protect • The memory card is write-protected. Release the write protection.
6.2.17 Alarm History-related Operation Messages

Message Details
The collection begin? (Y/N) • Determines whether to start alarm history. Press [Y] or [INPUT] to
start alarm history.
The collection stop? (Y/N) • Determines whether to stop alarm history. Press [Y] or [INPUT] to
stop alarm history.
The collection is being executed • An attempt was made to start alarm history while alarm history was
being performed.
The collection is stopping • An attempt was made to stop alarm history while alarm history was
being stopped.
Execute the collection data • Determines whether to clear alarm history. Press [Y] or [INPUT] to
clear?(Y/N) clear alarm history.
Data clear complete • The alarm history cleared was completed.
The collection begin • The alarm history was started.
The collection stop • The alarm history was stopped.
IV - 98
Appendix 6. Alarms
6.2.18 Anshin-net-related Operation Messages

(1) Messages related to all Anshin-net screens
Message Details
(None) Press one-touch call to • Communication has not been started.
call the NC service. • A call is being placed with automatic alarm
notification or one-touch call, and a call is being
Do not turn the power OFF
received from the NC service.
during the one-touch call.
(2) Messages related to automatic alarm notification

Message Details
dialing Do not turn the power OFF • A call is being placed with automatic alarm
until the automatic alarm notification.
• Communication starts when an alarm occurs,
notification ends.
but the line is not connected yet in this state.
• This state is also entered when standing by for
transmission.
• Communication has been started with
emergency stop by the servo, spindle or PLC
alarm, or by the establishment of the conditions
set in the parameters.
Waiting for dialing Do not turn the power OFF ● Redialing since the NC service is using the line
until the automatic alarm for other communication.
notification ends.
Verifying the user Do not turn the power OFF • User authentication is being executed by the
registration until the automatic alarm NC service side.
notification ends.
Connecting Do not turn the power OFF • The line is connected with automatic alarm
until the automatic alarm notification.
notification ends.
Receiving Do not turn the power OFF • The diagnosis data is being received with
until the automatic alarm automatic alarm notification.
notification ends.
Sending Do not turn the power OFF • The diagnosis data is being sent with automatic
until the automatic alarm alarm notification.
notification ends.
Transmission Press one-touch call to • Automatic alarm notification has ended, and the
completed call the NC service. line has been disconnected.
Reception completed Press one-touch call to • Automatic alarm notification has ended, and the
call the NC service. line has been disconnected.
• This is displayed when at least one file has
been received.
(Status of Connecting with NC • In connection standby state since line is being
communication with service. used by Anshin-net.
NC service) Wait for communication to
end.
IV - 99
Appendix 6. Alarms

Message Details
Operator notice If automatic operation • Operator notification is valid.
effective stops while operator • If machining ends normally or abnormally in this
state, communication with operator notification
notification is valid, the
will start.
designated telephone
number will be contacted.
Dialing Do not turn the power OFF • Data is being transmitted with operator
until the operator notification.
• Communication will start when machining ends
notification ends.
normally or abnormally, but the line is not
connected yet in this state.
transmission.
Waiting for dialing Do not turn the power OFF • Redialing since the NC service is using the line
until the operator for other communication.
notification ends.
registration until the operator NC service side.
notification ends.
Connecting Do not turn the power OFF • The line is connected with operator notification.
until the operator
notification ends.
until the operator operator notification.
notification ends.
Sending Do not turn the power OFF • The diagnosis data is being sent with operator
until the operator notification.
notification ends.
Transmission Press one-touch call to • Operator notification has ended, and the line
completed call the NC service. has been disconnected.
Reception completed Press one-touch call to • Operator notification has ended, and the line
call the NC service. has been disconnected.
been received.
end.
IV - 100
Appendix 6. Alarms

Message Details
Carry out one-touch Press "Y" to make a • A connection with NC service has not been
call? (Y/N) one-touch call and "N" to established.
• The system is confirming whether to actually
cancel.
make a one-touch call.
If the line is being in use, a • This is displayed when the Call menu is
connection with NC pressed. Press Y or INPUT to execute
service will be established one-touch call.
as soon as the line
becomes idle.
Message Details
Dialing Do not turn the power OFF • Data is being transmitted with one-touch call.
until the one-touch call • Communication will start when one-touch call is
executed, but the line is not connected yet in
ends.
this state.
transmission.
Waiting for dialing Do not turn the power OFF • Redialing since the NC service is using the line
until the one-touch call for other communication.
ends.
registration until the one-touch call NC service side.
ends.
Connecting Do not turn the power OFF • The line is connected with one-touch call.
until the one-touch call
ends.
until the one-touch call one-touch call.
ends.
Sending Do not turn the power OFF • The diagnosis data is being sent with one-touch
until the one-touch call call.
ends.
Transmission Press one-touch call to • Communication with one-touch call has ended,
completed call the NC service. and the line has been disconnected.
Reception completed Press one-touch call to • Communication with one-touch call has ended,
call the NC service. and the line has been disconnected.
been received.
end.
IV - 101
Appendix 6. Alarms
(5) Messages related to transmission request from NC service

Message Details
Verifying the Connecting with NC • User authentication is being executed by the
distination service. NC system side.
Wait for communication to
end.
Connecting Connecting with NC • The line is connected upon transmission
service. request from NC service.
end.
Receiving Connecting with NC • Data is being received upon transmission
service. request from NC service.
end.
Sending Connecting with NC • Data is being sent upon transmission request
service. from NC service.
end.
Transmission Press one-touch call to • Transmission request from NC service has
completed call the NC service. been completed, and the line has been
disconnected.
Reception completed Press one-touch call to • Transmission request from NC service has
call the NC service. been completed, and the line has been
disconnected.
• This is displayed when at least one file or
during the one-touch call. message has been received.
(6) Messages related to number 1 to 3 menu operations

Message Details
(None) Press one-touch call to • The selected telephone No. will be set as the
call the NC service. telephone No. to be notified to the NC service.
• Hereafter, the telephone No. set with one-touch
call or operator notification will be notified to the
during the one-touch call. NC service.
(7) Messages related to arbitrary number setting

Message Details
(None) Input the telephone No. to • The input telephone No. will be set as the
be notified. telephone No. to be notified to the NC service.
• Hereafter, the telephone No. set with one-touch
call or operator notification will be notified to the
NC service.
IV - 102
Appendix 6. Alarms
(8) Messages related to sharing of machining data

Message Details
Transmit by the set • The line is not connected with NC service.
password?(Y/N) • The system is confirming whether to transfer machining data. Press
"Y" or "INPUT" to transfer machining data, "N" to cancel.
OK? (Y/N) • The line is not connected with NC service.
• The system is confirming whether to erase machining data. Press
"Y" or "INPUT" to erase machining data, "N" to cancel.
dialing • A call is being placed.
• "Transmit by the set password?(Y/N)" or "OK? (Y/N)" is shown.
Pressing "Y" or "INPUT" starts the communication. The line is not
connected yet in this state.
Connecting • The line is connected for sharing of machining data.
Transmitting • The machining data is being transmitted.
Transmission completed • Machining data transmission has ended, and the line has been
disconnected.
Receiving • The machining data is being received.
Reception completed • Machining data reception has ended, and the line has been
disconnected.
Erase complete • Machining data erasing has ended, and the line has been
disconnected.
Waiting for dialing • In dialing standby state since the line is being used.
Input the password • The password, which is required for the transmission/reception of
machining data, has not been set. Input the password set on the
Anshin-net parameter 1 screen.
Input the user number • The user number, which is required for the transmission/reception
of machining data, has not been set. Input the user number set on
the Anshin-net parameter 1 screen.
IV - 103
Appendix 6. Alarms
6.2.19 Messages Related to Machine Tool Builder Network System

(1) Messages related to all Machine Tool Builder Network System (MTB net) Screens.
Message Details
(None) Press the [Send] menu • Communication has not been started.
when you transmit the
diagnosis data to MTB.
Don't turn OFF the power
supply while transmitting.
Message Details
Network service is connected • The settings of the MTB net parameter 1,2 cannot be changed
since the system is communicating with Call Center or machine
tool builder. Set again after the communication has ended.
(2) Messages related to transmission of diagnosis data

Message Details
Transmit diagnosis Press Y (transmit the • The system is confirming the transmission of
data? (Y/N) diagnosis data) or N (cancel). diagnosis data.
You'll connect with MTB
when it gets available if line
used.
dialing Don't turn OFF a power • The diagnosis data is being transmitted.
supply until diagnosis data • The line is not connected yet in this state.
transmission ends.
Verifying the user Don't turn OFF a power • The system is waiting for an authentication
registration supply until diagnosis data response from remote diagnosis tool kit.
transmission ends.
Waiting for the reply Don't turn OFF a power • The line has been disconnected once, and
supply until diagnosis data the system is waiting for a connection with
the machine tool builder.
transmission ends.
Verifying the Don't turn OFF a power • The line has been connected corresponding
destination supply until diagnosis data to the received call from the machine tool
builder. The system is confirming the
transmission ends. destination of connection.
Connecting Don't turn OFF a power • The system is connected or connecting with
supply until diagnosis data machine tool builder.
transmission ends.
Transmitting Don't turn OFF a power • The diagnosis data is actually being
supply until diagnosis data transmitted.
transmission ends.
Transmission Press Y (transmit the • The transmission of diagnosis data has
completed diagnosis data) or N (cancel). ended, and the line has been disconnected.
You'll connect with MTB
when it gets available if line
used.
IV - 104
Appendix 6. Alarms
Message Details
Waiting for dialing Don't turn OFF a power • The machine tool builder is using the line for
supply until diagnosis data other communication.
transmission ends.
(Status of Connecting with NC service. • In connection standby state since line is being
communication with Please wait until the used by Anshin-net.
NC service) communication ends.
(Status of Connecting with MTB. • In connection standby state since line is being
communication with Please wait until the used by the machine tool builder.
machine communication ends.
manufacturer)
(3) Messages related to reception of the diagnosis results

Message Details
Verifying the Connecting with MTB. • The line has been connected corresponding
destination Please wait until the to the received call from the machine tool
builder. The system is confirming the
communication ends. destination of connection.
Connecting Connecting with MTB. • The system is connected or connecting with
Please wait until the machine tool builder.
communication ends.
Receiving Connecting with MTB. • The diagnosis results are actually being
Please wait until the received.
communication ends.
Reception completed Press the [Send] menu • Reception of the diagnosis results has ended,
when you transmit the and the line has been disconnected.
(4) Messages related to reception of messages

Message Details
Verifying the Connecting with MTB. • The line has been connected corresponding to
destination Please wait until the the received call from the machine tool builder.
The system is confirming the destination of
communication ends. connection.
Connecting Connecting with MTB. • The system is connected or connecting with
Please wait until the machine tool builder.
communication ends.
Reception completed Press the [Send] menu • Reception of the message has ended, and the
when you transmit the line has been disconnected.
IV - 105
Appendix 6. Alarms
6.2.20 Other Operation Messages

Message Details
Executing automatic operation • Cannot be performed during automatic operation.
Perform the operation again after automatic operation has been
completed.
Setting error • The setting data is inadequate. (Alphabetic characters were set
where only numeric characters can be set, etc.)
• The data has not been set.
• There is no specification.
Data range error • The input data exceeded the range.

Set the value again within the range.
Data protect • Setting, erasing, parameter setting, etc., of the various data is
prohibited, because the data protect key is validated.
Reconsider the data protect key setting.
Write protect • Attempted to create a new program file in the write-protected device
• Opened the program file of the write-protected device
• Attempted to save the program file of the write-protected device
• Attempted to correct the buffer for the write-protected file.
• Attempted to edit or correct the buffer for the read-only program file.
Edit lock B • It is not possible to change machining program B (8000 to 8999: user
standard subprogram) or machining program C (9000 to 9999:
machine tool builder custom program) as edit lock B is enabled.
Edit lock C • It is not possible to change machining program C (9000 to 9999:
machine tool builder custom program) as edit lock C is enabled.
Origin set not possible • The operation is in a state in which origin set is not possible.
Check the parameter "#1123 origin (Origin set prohibited)" setting.
• Check that the axis has stopped.
• Check that idling (post-reset status) is currently being performed.
Can't command manual value • The manual numerical value protect is valid and therefore it is not
possible to perform a manual numerical value command.
Getting T code list • T code list is being retrieved.
T code list complete • Retrieving T code list is completed.
Load meter display not possible • The load meter cannot be displayed.
Contact the machine tool builder.
Pallet running • Each setting was executed during pallet running.
APC executing • Each setting was executed during automatic pallet changer
executing.
IV - 106
Appendix 6. Alarms
6.3 Program Error
6.3 Program Error

(The bold characters are the message displayed in the screen.)
These alarms occur during automatic operation‚ and the causes of these alarms are mainly program errors
which occur‚ for instance‚ when mistakes have been made in the preparation of the machining programs or
when programs which conform to the specification have not been prepared.

P 10 No. of simultaneous axes over • Divide the alarm block command into two.
The number of axis addresses commanded in • Check the specifications.
the same block exceeds the specifications.
P 11 Illegal axis address • Revise the axis names in the program.
The axis address commanded by the
program and the axis address set by the
parameter do not match.
P 20 Division error • Check the program.
An axis command which cannot be divided by
the command unit has been issued.
P 29 Not accept command • Check the program.
The normal line control command (G40.1,
G41.1, G42.1) has been issued during the
modal in which the normal line control is not
acceptable.
P 30 Parity H error • Check the paper tape.
The number of holes per character on the • Check the tape puncher and tape reader.
paper tape is even for EIA code and odd for
ISO code.
P 31 Parity V error • Make the number of characters per block on
The number of characters per block on the the paper tape even.
paper tape is odd. • Set the parameter parity V selection OFF.
P 32 Illegal address • Check and revise the program address.
An address not listed in the specifications has • Check and correct the parameters values.
been used. • Check the specifications.
P 33 Format error • Check the program.
The command format in the program is not
correct.
P 34 Illegal G code • Check and correct the G code address in the
A G code not listed in the specifications has program.
been used.
An illegal G code was commanded during the
coordinate rotation command (G68).
G51.2 or G50.2 was commanded when the • Check the parameter setting values.
rotary tool axis No. (#1501 polyax) was set to
"0".
G51.2 or G50.2 was commanded when the
tool axis was set to the linear axis (#1017 rot
"0").
P 35 Setting value range over • Check the program.
The setting range for the addresses has been
exceeded.
P 36 Program end error • Enter the M02 and M30 command at the end
"EOR" has been read during tape and of the program.
memory mode. • Enter the M99 command at the end of the
subprogram.
IV - 107
Appendix 6. Alarms
6.3 Program Error

P 37 O, N number zero • The program Nos. are designated across a
A zero has been specified for program and range from 1 to 99999999.
sequence Nos. • The sequence Nos. are designated across a
range from 1 to 99999.
P 39 No specifications • Check the specifications.
• A non-specified G code was specified.
• The selected operation mode is not used.
P 40 Pre-read block error • Reconsider the program.
When tool radius compensation is executed‚
there is an error in the pre-read block and so
the interference check is disabled.
P 48 Restart pos return incomplete • Carry out program restart again. Movement
Movement command was executed before command cannot be executed before
executing the block that is restart-searched. executing the block that is restart-searched.
P 49 Invalid restart search • Reconsider the program.
• Restart search was attempted for the • Reconsider the restart search position.
3-dimensional circular interpolation.
• Restart search was attempted during the
cylindrical interpolation, polar coordinate
interpolation, and tool tip center control.
P 50 No spec: Inch/Metric change • Check the specifications.
Inch/Metric changeover (G20/G21) command
was issued even though there is no
inch/metric conversion specification.
P 60 Compensation length over • Reconsider the axis address command.
The commanded movement distance is
excessive. (Over 231)
P 61 No spec: Unidirectional posit. • Check the specifications.
Unidirectional positioning (G60) was
commanded even though there is no
unidirectional positioning specification.
P 62 No F command • The default movement modal command at
• No feed rate command has been issued. power ON is G01. This causes the machine
• There is no F command in the cylindrical to move without a G01 command if a
interpolation or polar coordinate movement command is issued in the
interpolation immediately after the G95 program, and an alarm results. Use an F
mode is commanded. command to specify the feed rate.
• Specify F with a thread lead command.
P 63 No spec: High-speed machining • Check the specifications.
High-speed machining cancel (G5P0) was
high-speed machining mode specification.
P 65 No spec: High speed mode 3 • Check the high-speed mode III specifications.
P 70 Arc end point deviation large • Check the numerical values of the addresses
• There is an error in the arc start and end that specify the start and end points, arc
points as well as in the arc center. center as well as the radius in the program.
• The difference of the involute curve through • Check the "+" and "-" directions of the
the start point and the end point is large. address numerical values.
• When arc was commanded, one of the two • Check the scaling valid axis.
axes configuring the arc plane was a
scaling valid axis.
IV - 108
Appendix 6. Alarms
6.3 Program Error

P 71 Arc center error • Check the numerical values of the addresses
• The arc center is not sought during in the program.
R-specified circular interpolation. • Check whether the start point or end point is
• The curvature center of the involute curve on the inner side of the base circle for involute
cannot be obtained. interpolation. When carrying out tool radius
compensation, check that the start point and
end point after compensation are not on the
inner side of the base circle for involute
interpolation.
• Check whether the start point and end point
are at an even distance from the center of the
base circle for involute interpolation.
P 72 No spec: Herical cutting • Check the helical specifications.
A helical command has been issued though it • An Axis 3 command was issued by the
is not included in the specifications. circular interpolation command. If there is
no helical specification, the linear axis is
moved to the next block.
P 73 No spec: Spiral cutting • The G02.1 and G03.1 commands are issued
A spiral command was issued despite the fact for circular interpolation.
that such a command does not exist in the • Check the spiral specifications.
specifications.
P 74 Can't calculate 3DIM arc • Reconsider the program.
The end block was not specified during
3-dimension circular interpolation
supplementary modal, and therefore it is not
possible to calculate the 3-dimension circular
interpolation.
Furthermore, it not possible to calculate the
3-dimension circular interpolation due to an
interruption during 3-dimension circular
interpolation supplementary modal.
P 75 3DIM arc illegal • Reconsider the program.
An unusable G code was issued during
3-dimension circular interpolation modal.
Or, a 3-dimension circular interpolation
command was issued during a modal for
which a 3-dimension circular interpolation
command cannot be issued.
P 76 No spec: 3DIM arc interpolat • Check the specifications.
G02.4/G03.4 was commanded even though
there is no 3-dimension circular interpolation
specification.
P80 No spec: Hypoth ax interpolat • Check the specifications.
Hypothetical axis interpolation (G07) was
hypothetical axis interpolation specification.
P 90 No spec: Thread cutting • Check the specifications.
A thread cutting command was issued even
though there is no thread cutting command
specification.
P 91 No spec: Var lead threading • Check the specifications.
Variable lead thread cutting (G34) was
commanded even though there is no variable
lead thread cutting specification.
IV - 109
Appendix 6. Alarms
6.3 Program Error

P 93 Illegal pitch vaule • Set the correct thread lead command for the
The thread lead (thread pitch) when thread cutting command.
performing the thread cutting command is
incorrect.
P100 No spec: Cylindric interpolat • Check the specifications.
A cylindrical interpolation command was
issued even though there is no cylindrical
interpolation specification.
P110 Plane select during figure rot • Check the machining program.
Plane selection (G17/G18/G19) was
commanded during figure rotation.
P111 Plane selected while coord rot • After command G68, always issue a plane
Plane selection commands (G17, G18, G19) selection command following a G69
were issued during a coordinate rotation (coordinate rotation cancel) command.
command (G68).
P112 Plane selected while R compen • Issue plane selection commands after
• Plane selection commands (G17, G18, completing (axis movement commands
G19) were issued while tool radius issued after G40 cancel command) tool
compensation (G41, G42) and nose R radius compensation and nose R
compensation (G41, G42, G46) commands compensation commands.
were being issued.
• Plane selection commands were issued
after completing nose R compensation
commands when there are no further axis
movement commands after G40, and
compensation has not been cancelled.
P113 Illegal plane select • Issue a circular command after correct plane
The circular command axis differs from the selection.
selected plane.
P120 No spec: Feed per rotation • Check the specifications.
Feed per rotation (G95) was commanded
even though there is no feed per rotation
specification.
P121 F0 command during arc modal • Check the machining program.
F0 (F 1-digit feed) was commanded during
the arc modal (G02/G03).
P122 No spec: Auto corner override • Check the specifications.
An auto corner override command (G62) was • Delete the G62 command from the program.
issued even though there is no auto corner
override specification.
P123 No spec: High-accuracy control • Check the specifications.
High-accuracy control command was issued
even though there is no high-accuracy control
specification
P124 No spec: Inverse time feed • Check the specifications.
There is no inverse time option.
P125 G93 mode error • Reconsider the program.

• A G code command that cannot be issued
was issued during G93 mode.
• G93 command was issued during a modal
for which inverse time feed cannot be
performed.
IV - 110
Appendix 6. Alarms
6.3 Program Error

P126 Invalid cmnd in high-accuracy • Reconsider the program.
An illegal command was issued during the
• A G code group 13 command was issued
during the high-accuracy control mode.
• Milling, cylindrical interpolation or pole
coordinate interpolation was commanded
during the high-accuracy control mode.
P127 No spec: SSS Control • Check the specifications.
The SSS control valid parameter was set to If there is no SSS control specification, set the
ON although there is no SSS control parameter #8090 SSS ON to 0.
specification.
P130 2nd M function code illegal • Check and correct the 2nd miscellaneous
The 2nd miscellaneous function address function address in the program.
commanded in the program differs from the
address set in the parameters.
miscellaneous function.
P131 No spec: Cnst surface ctrl G96 • Check the specifications.
A constant surface speed control command • Change the constant surface speed control
(G96) was issued even though there is no command (G96) to a rotation speed
specification. command (G97).
P132 Spindle rotation speed S=0 • Reconsider the program.
No spindle rotation speed command has
been issued.
P133 Illegal P-No. G96 • Reconsider the parameter specified for the
An invalid constant surface speed control axis constant surface speed control axis.
has been specified.
P140 No spec: Pos compen cmd • Check the specifications.
The position compensation command (G45
to G48) specifications are not available.
P141 Pos compen during rotation • Reconsider the program.
Position compensation was commanded
during the figure rotation or coordinate
rotation command.
P142 Pos compen invalid arc • Reconsider the program.
A position compensation invalid arc
command was commanded.
P150 No spec: Nose R compensation • Check the specifications.
• Even though there were no tool radius
compensation specifications, tool radius
compensation commands (G41 and G42)
were issued.
• Even though there were no nose R
compensation specifications, nose R
compensation commands (G41, G42, and
G46) were issued.
P151 Radius compen during arc mode • Issue the linear command (G01) or rapid
A compensation command (G40‚ G41‚ G42‚ traverse command (G00) in the
G43‚ G44‚ G46) has been issued in the arc compensation command block or cancel
modal (G02‚ G03). block.
(Set the modal to linear interpolation.)
IV - 111
Appendix 6. Alarms
6.3 Program Error

P152 No intersection • Reconsider the program.
In interference block processing during
execution of a tool radius compensation (G41
or G42) or nose R compensation (G41‚ G42‚
or G46) command‚ the intersection point after
one block is skipped cannot be determined.
P153 Compensation interference • Reconsider the program.
An interference error has arisen while the tool
radius compensation command (G41‚ G42) or
nose R compensation command (G41‚ G42‚
G46) was being executed.
P154 No spec: 3D compensation • Check the specifications.
A three-dimensional compensation command
was issued even though there are no
three-dimensional compensation
specifications.
P155 Fixed cyc exec during compen • The radius compensation mode is established
A fixed cycle command has been issued in when a fixed cycle command is executed and
the radius compensation mode. so the radius compensation cancel command
(G40) should be issued.
P156 R compen direction not defined • Change the vector to that with which the
At the start of G46 nose R compensation‚ the compensation direction is defined.
compensation direction is undefined if this • Exchange with a tool having a different tip
shift vector is used. point No.
P157 R compen direction changed • Change the G command to that which allows
During G46 nose R compensation‚ the inversion of the compensation direction (G00‚
compensation direction is inverted. G28‚ G30‚ G33‚ or G53).
• Exchange with a tool having a different tip
point No.
• Turn ON the "#8106 G46 NO REV-ERR"
parameter.
P158 Illegal tip point • Change the tip point No. to a legal one.
During G46 nose R compensation‚ the tip
point is illegal (other than 1 to 8).
P170 No offset number • Add the compensation No. command to the
The compensation No. (DOO‚ TOO‚ HOO) compensation command block.
command was not given when the radius • Check the number of compensation No. sets
compensation (G41‚ G42‚ G43‚ G46) a correct it to a compensation No. command
command was issued. Alternatively‚ the within the permitted number of tool
compensation No. is larger than the number compensation sets.
of sets in the specifications.
P171 No spec:Comp input by prog G10 • Check the specifications.
Compensation data input by program (G10)
was commanded even though there is no
specification of compensation data input by
program.
P172 G10 L number error • Check the address L-No. of the G10
(G10 L-No. error) command and correct the No.
The L address command is not correct when
the G10 command is issued.
IV - 112
Appendix 6. Alarms
6.3 Program Error

P173 G10 P number error • First check the number of compensation sets
(G10 compensation error) and then set the address P designation to
When the G10 command is issued‚ a within the permitted number of sets.
compensation No. outside the permitted
number of sets in the specifications has been
commanded for the compensation No.
command.
P174 No spec:Comp input by prog G11 • Check the specifications.
Compensation data input by program cancel
(G11) was commanded even though there is
no specification of compensation data input
by program.
P177 Tool life count active • The tool life management data cannot be
Registration of tool life management data with registered when counting the used data. Turn
G10 was attempted when the used data count the used data count valid signal OFF.
valid signal was ON.
P178 Tool life data entry over • Review the number of registrations.
The number of registration groups‚ total
number of registered tools or the number of
registrations per group exceeded the
specifications range.
P179 Illegal group No. • The group No. cannot be commanded in
• When registering the tool life management duplicate. When registering the group data‚
data with G10‚ the group No. was register it in group units.
commanded in duplicate. • Correct to the correct group No.
• A group No. that was not registered was
designated during the T 99
command.
• An M code command must be issued as a
single command but coexists in the same
block as that of another M code command.
• The M code commands set in the same
group exist in the same block.
P180 No spec: Drilling cycle • Check the specifications.
A fixed cycle command was issued though • Correct the program.
there are not fixed cycle (G72 - G89)
specifications.
P181 No spindle command (Tap cycle) • Issue the spindle rotation speed command
The spindle rotation speed command has not (S) when the fixed cycle for drilling command
been issued when the fixed cycle for drilling G84‚ G74 (G84‚ G88) is given.
command is given. • Enter "S*****" type S command.
"S*****" type S command does not exist in the
same block with the synchronous tapping
cycle.
P182 Synchronous tap error • Check connection to the main spindle.
• Connection to the main spindle unit was not • Check that the main spindle encoder exists.
established. • Set 1 to the parameter #3024 (sout).
• The synchronous tapping was attempted
with the spindle not serially connected
under the multiple-spindle control I.
P183 No pitch/thread number • Specify the pitch data and the number of
The pitch or thread number command has not threads by F or E command.
been issued in the tap cycle of a fixed cycle
for drilling command.
IV - 113
Appendix 6. Alarms
6.3 Program Error

P184 Pitch/thread number error • Check the pitch or the number of threads per
• The pitch or the number of threads per inch inch.
is illegal in the tap cycle of the fixed cycle
for drilling command.
• The pitch is too small for the spindle rotation
speed.
• The thread number is too large for the
spindle rotation speed.
P185 No spec: Sync tapping cycle • Check the specifications.
Synchronous tapping cycle (G84/G74) was
synchronous tapping cycle specification.
P186 Illegal S cmnd in synchro tap • Cancel the synchronous tapping before
S command was issued during synchronous
tapping modal. issuing the S command.
P190 No spec: Turning cycle • Check the specification.

A lathe cutting cycle command was input • Delete the lathe cutting cycle command.
although the lathe cutting cycle was
undefined in the specification.
P191 Taper length error • The radius set value in the lathe cycle
In the lathe cutting cycle‚ the specified length command must be smaller than the axis shift
of taper section is illegal. amount.
P192 Chamfering error • Set a chamfering amount not exceeding the
Chamfering in the thread cutting cycle is cycle.
illegal.
P200 No spec: MRC cycle • Check the specification.
The compound type fixed cycle for turning
machining I (G70 to G73) was commanded
when the compound type fixed cycle for
turning machining I specifications were not
provided.
P201 Program error (MRC) • Delete the following G codes from this
• When called with a compound type fixed subprogram that is called with the compound
cycle for turning machining I command, the type fixed cycle for turning machining I
subprogram contained at least one of the commands (G70 to G73): G27‚ G28‚ G29,
following commands: G30‚ G31‚ G33‚ G34, and fixed cycle G
• Reference position return command codes.
(G27, G28, G29, G30) • Remove G2 and G3 from the first move block
• Thread cutting (G33, G34) of the finish shape program in compound type
• Fixed cycle skip-function (G31, G31.n) fixed cycle for turning machining I.
• The first move block of the finish shape
program in compound type fixed cycle for
turning machining I contains an arc
command.
P202 Block over (MRC) • Specify 50 or a less value. The number of
The number of blocks in the shape program blocks in the shape program called by the
of the compound type fixed cycle for turning compound type fixed cycle for turning
machining I is over 50 or 200 (this differs machining I commands (G70 to G73) must be
according to the model). decreased below 50 or 200 (this differs
according to the model).
IV - 114
Appendix 6. Alarms
6.3 Program Error

P203 D cmnd figure error (MRC) • Check the compound type fixed cycle for
The compound type fixed cycle for turning turning machining I (G70 to G73) shape
machining I (G70 to G73) shape program program.
could not cut the work normally because it
defined an abnormal shape.
P204 E cmnd fixed cycle error • Check the compound type fixed cycle for
A command value of the compound type fixed turning machining (G70 to G76) command
cycle for turning machining (G70 to G76) is value.
illegal.
P210 No spec: Pattern cycle • Check the specification.
A compound type fixed cycle for turning
machining II (G74 to G76) command was
input although it was undefined in the
specification.
P220 No spec: Special fixed cycle • Check the specifications.
No special fixed cycle specifications are
available.
P221 No. of special fixed holes = 0 • Reconsider the program.
A 0 has been specified for the number of
holes in special fixed cycle mode.
P222 G36 angle error • Reconsider the program.
A G36 command specifies 0 for angle
intervals.
P223 G12/G13 radius error • Reconsider the program.
The radius value specified with a G12 or G13
command is below the compensation
amount.
P224 No spec: Circular (G12/G13) • Check the specifications.
There are no circular cutting specifications.
P230 Subprogram nesting over • Check the number of subprogram calls and
• A subprogram has been called 8 or more correct the program so that it does not exceed
times in succession from the subprogram. 8 times.
• The program in the data server contains the
M198 command.
• The program in the IC card has been called
more than once (the program in the IC card
can be called only once at a time).
P231 No sequence No. • Specify the sequence Nos. in the call block of
At subprogram call time‚ the sequence No. the subprogram.
set at return from the subprogram or specified
by GOTO‚ was not set.
P232 No program No. • Enter the machining program.
• The machining program has not been found • Check the subprogram storage destination
when the machining program is called. parameters.
• The file name of the program registered in • Ensure that the external device (including IC
IC card is not corresponding to O No. card) that contains the file is mounted.
P235 Program editing • Execute the program again after completion
Operation was attempted for the file under of program editing.
program editing.
P240 Program editing • Check the specifications.
Operation was attempted for the file under
program editing.
IV - 115
Appendix 6. Alarms
6.3 Program Error

P241 No variable No. • Check the specifications.
The variable No. commanded is out of the • Check the program variable No.
range specified in the specifications.
P242 = not defined at vrble set • Designate the "=" sign in the variable
The "=" sign has not been commanded when definition of the program.
a variable is defined.
P243 Can't use variables • Correct the program.
An invalid variable has been specified in the
left or right side of an operation expression.
P244 Invalid set date or time • Date or time cannot be changed.
Date or time was set earlier than current date • Reconsider the program.
or time in the system variables (#3011,
#3012) when the credit system was valid.
P250 No spec: Figure rotation • Check the specifications.
Figure rotation (M98 I_J_P_H_L_) was
commanded even though there is no figure
rotation specification.
P251 Figure rotation overlapped • Check the machining program.
Figure rotation command was issued during
figure rotation.
P252 Coord rotate in fig. rotation • Reconsider the program.
A coordinate rotation related command (G68,
G69) was issued during figure rotation.
P260 No spec: Coordinates rotation • Check the specifications.
Even though there were no coordinate
rotation specifications, a coordinate rotation
command was issued.
P270 No spec: User macro • Check the specifications.
A macro specification was commanded
though there are no such command
specifications.
P271 No spec: Macro interrupt • Check the specifications.
A macro interruption command has been
issued though it is not included in the
specifications.
P272 NC and macro texts in a block • Reconsider the program and place the
A statement and a macro statement exist executable statement and macro statement in
together in the same block. separate blocks.
P273 Macro call nesting over • Reconsider the program and correct it so that
The number of macro call nests exceeded the the macro calls do not exceed the limit
specifications. imposed by the specification.
P275 Macro argument over • Reconsider the program.
The number of macro call argument type II
sets has exceeded the limit.
P276 Illegal G67 command • Reconsider the program.
A G67 command was issued though it was • The G67 command is the call cancel
not during the G66 command modal. command and so the G66 command must be
designated first before it is issued.
P277 Macro alarm message • Refer to the operator messages on the DIAG
An alarm command has been issued in screen.
#3000. • Refer to the instruction manual issued by the
IV - 116
Appendix 6. Alarms
6.3 Program Error

P280 Brackets [ ] nesting over • Reconsider the program and correct it so the
The number of parentheses "[" or "]" which number of "[" or "]" is five or less.
can be commanded in a single block has
exceeded five.
P281 Brackets [ ] not paired • Reconsider the program and correct it so that
The number of "[" and "]" parentheses "[" and "]" parentheses are paired up properly.
commanded in a single block does not match.
P282 Calculation impossible • Reconsider the program and correct the
The arithmetic formula is incorrect. formula.
P283 Divided by zero • Reconsider the program and correct it so that
The denominator of the division is zero. the denominator for division in the formula is
not zero.
P290 IF sentence error • Reconsider the program.
There is an error in the IF conditional
GOTO statement.
P291 WHILE sentence error • Reconsider the program.
There is an error in the WHILE conditional
DO -END statement.
P292 SETVN sentence error • Reconsider the program.
There is an error in the SETVN statement • The number of characters in the variable
when the variable name setting was made. name of the SETVN statement must be 7 or
less.
P293 DO-END nesting over • Reconsider the program and correct it so that
The number of DO-END nesting levels in the nesting levels of the DO - END statement
WHILE conditional DO -END statement does not exceed 27.
has exceeded 27.
P294 DO and END not paired • Reconsider the program and correct it so that
The DO's and END's are not paired off the DO's and END's are paired off properly.
properly.
P295 WHILE/GOTO in tape • During tape operation‚ a program which
There is a WHILE or GOTO statement on the includes a WHILE or GOTO statement cannot
tape during tape operation. be executed and so the memory operation
mode is established instead.
P296 No address (macro) • Review the program.
A required address has not been specified in
the user macro.
P297 Address-A error • Review the program.
The user macro does not use address A as a
variable.
P298 G200-G202 cmnd in tape • Review the program.
User macro G200‚ G201‚ or G202 was
specified during tape or MDI mode.
P300 Variable name illegal • Reconsider the variable names in the
The variable names have not been program and correct them.
commanded properly.
P301 Variable name duplicated • Correct the program so that the name is not
The name of the variable has been duplicated.
duplicated.
P310 Not use GMSTB macro code • Review the program.
G, M, S, T, or B macro code was called • Review the parameter.
during fixed cycle.
IV - 117
Appendix 6. Alarms
6.3 Program Error

P350 No spec: Scaling command • Check the specifications.
The scaling command (G50, G51) was
issued when the scaling specifications were
not available.
P360 No spec: Program mirror • Check the specifications.
A mirror image (G50.1 or G51.1) command
has been issued though the programmable
mirror image specifications are not provided.
P370 No spec: Facing t-post MR • Check the specifications.
The facing turret mirror image specifications
are not provided.
P371 Facing t-post MR illegal • Check the program.
Mirror image for facing tool posts was • Check the parameters.
commanded to an axis for which external
mirror image or parameter mirror image is
valid.
Mirror image for facing tool posts validating
mirror image for a rotary axis was
commanded.
P380 No spec: Corner R/C • Check the specifications.
The corner R/C was issued when the corner • Remove the corner chamfering/corner
R/C specifications were not available. rounding command from the program.
P381 No spec: Arc R/C • Check the specifications.

Corner chamfering II /corner rounding II was
specified in the arc interpolation block
although corner chamfering/corner rounding II
is unsupported.
P382 No corner movement • Replace the block succeeding the corner
The block next to corner chamfering/ chamfering/corner rounding command by
corner rounding is not a movement G01 command.
command.
P383 Corner movement short • Make the corner chamfering/corner rounding
In the corner chamfering/corner rounding less than the movement distance since this
command‚ the movement distance was distance is shorter than the corner chamfering/
shorter than the value in the corner corner rounding.
chamfering/corner rounding command.
P384 Corner next movement short • Make the corner chamfering/corner rounding
When the corner chamfering/corner rounding less than the movement distance since this
command was input‚ the movement distance distance in the following block is shorter than
in the following block was shorter than the the corner chamfering/corner rounding.
length of the corner chamfering/corner
rounding.
P385 Corner during G00/G33 • Recheck the program.
A block with corner chamfering/corner
rounding was given during G00 or G33
modal.
P390 No spec: Geometric • Check the specifications.
A geometric command was issued though
there are no geometric specifications.
P391 No spec: Geometric arc • Check the specifications.
There are no geometric IB specifications.
IV - 118
Appendix 6. Alarms
6.3 Program Error

P392 Angle < 1 degree (GEOMT) • Correct the geometric angle.
The angular difference between the
geometric line and line is 1° or less.
P393 Inc value in 2nd block (GEOMT) • Specify this block by an absolute value.
The second geometric block was specified by
an incremental value.
P394 No linear move command (GEOMT) • Specify the G01 command.
The second geometric block contains no
linear command.
P395 Illegal address (GEOMT) • Recheck the program.
The geometric format is invalid.
P396 Plane selected in GEOMT ctrl • Execute the plane switching command before
A plane switching command was executed geometric command processing.
during geometric command processing.
P397 Arc error (GEOMT) • Recheck the geometric circular arc command
In geometric IB‚ the circular arc end point and the preceding and following commands.
does not contact or cross the next block start
point.
P398 No spec: Geometric1B • Check the specifications.
Although the geometric IB specifications are
not included‚ a geometric command is given.
P420 No spec: Para input by program • Check the specifications.
Parameter input by program (G10) was
specification of parameter input by program.
P421 Parameter input error • Check the program.
• The specified parameter No. or set data is
illegal.
• An illegal G command address was input in
parameter input mode.
• A parameter input command was input
during fixed cycle modal or nose R
compensation.
• G10L50, G10L70, G11 were not
commanded in independent blocks.
P430 R-pnt return incomplete • Execute reference position return manually.
• A command was issued to move an axis‚ • The command was issued to an axis for
which has not returned to the reference which axis removal is validated so invalidate
position‚ away from that reference position. axis removal.
• A command was issued to an axis removal
axis.
P431 No spec: 2,3,4th R-point ret • Check the specifications.
A command for second‚ third or fourth
reference position return was issued though
there are no such command specifications.
P432 No spec: Start position return • Check the specifications.
Start position return (G29) was commanded
even though there is no start position return
specification.
P433 No spec: R-position check • Check the specifications.
Reference position check (G27) was
reference position check specification.
IV - 119
Appendix 6. Alarms
6.3 Program Error

P434 Compare error • Check the program.
One of the axes did not return to the
reference position when the reference
position check command (G27) was
executed.
P435 G27 and M commands in a block • An M code command cannot be issued in a
An M command was issued simultaneously in G27 command block and so the G27
the G27 command block. command and M code command must be
placed in separate blocks.
P436 G29 and M commands in a block • An M code command cannot be issued in a
An M command was issued simultaneously in G29 command block and so the G29
the G29 command block. command and M code command must be
placed in separate blocks.
P438 G52 invalid during G54.1 • Review the program.
A local coordinate system command was
issued during execution of the G54.1
command.
P450 No spec: Chuck barrier • Check the specification.
The chuck barrier on command (G22) was
specified although the chuck barrier was
undefined in the specification.
P451 No spec: Stroke chk bef travel • Check the specification.
Stroke check before travel (G22/G23) was
commanded even though there is no stroke
check before travel specification.
P452 Limit before travel exists • Review the coordinate values of the axis
An illegal command such as the start or end address commanded in the program.
point of the traveling axis is inside the
prohibited area or the axis passes through the
prohibited area, was detected when Stroke
check before travel (G22) was ON.
P460 Tape I/O error • Check the power and cable of the connected
An error has arisen in the tape reader or‚ devices.
alternatively‚ in the printer during macro • Check the I/O device parameters.
printing.
P461 File I/O error • In memory mode, the programs stored in
A file of the machining program cannot be memory may have been destroyed. Output
read. all of the programs and tool data once and
IC card has not been inserted. format them.
• Ensure that the external device (including an
IC card, etc) that contains the file is mounted.
• Check the parameters for HD operation or IC
card operation.
P462 Computer link commu error • "L01 Computer link error" is displayed
A communication error occurred during the simultaneously, so remedy the problem
BTR operation. according to the error No.
P480 No spec: Milling • Check the specification.
• Milling was commanded when the milling
specifications were not provided.
• Polar coordinate interpolation was
commanded when the polar coordinate
interpolation specifications were not
provided.
IV - 120
Appendix 6. Alarms
6.3 Program Error

P481 Illegal G code (mill) • Check the program.
• An illegal G code was used during the
milling mode.
• An illegal G code was used during
cylindrical interpolation or polar coordinate
interpolation.
• The G07.1 command was issued during the
tool radius compensation.
P482 Illegal axis (mill) • Check the machining program, parameters
• A rotary axis was commanded during the and PLC I/F signal.
milling mode.
• Milling was executed even though an illegal
value was set for the milling axis No.
• Cylindrical interpolation or polar coordinate
interpolation was commanded during mirror
image.
interpolation was commanded before the
tool compensation was completed after the
T command.
• G07.1 was commanded when cylindrical
interpolation was not possible (there is no
rotary axis, or external mirror image is ON).
• An axis other than a cylindrical coordinate
system axis was commanded during
cylindrical interpolation.
P484 R-pnt ret incomplete (mill) • Carry out manual reference position return.
• Movement was commanded to an axis that
had not completed reference position return
during the milling mode.
• Movement was commanded to an axis that
had not completed reference position return
during cylindrical interpolation or polar
coordinate interpolation.
IV - 121
Appendix 6. Alarms
6.3 Program Error

P485 Illegal modal (mill) • Check the program.
• The milling mode was turned ON during • Before issuing G12.1, issue G40 or G97.
nose R compensation or constant surface • Before issuing G12.1, issue a T command.
speed control. • Before issuing G13.1, issue G40.
• A T command was issued during the milling • Specify the radius value of a cylinder other
mode. than 0, or specify the X axis's current value
• The mode was switched from milling to other than 0 before issuing G12.1/G16.
cutting during tool compensation.
interpolation was commanded during the
constant surface speed control mode
(G96).
• The command unacceptable in the
cylindrical interpolation was issued.
• A T command was issued during the
cylindrical interpolation or polar coordinate
interpolation mode.
• A movement command was issued when
the plane was not selected just before or
after the G07.1 command.
• A plane selection command was issued
during the polar coordinate interpolation
mode.
interpolation was commanded during tool
radius compensation.
• The G16 plane in which the radius value of
a cylinder is 0 was specified.
• A cylindrical interpolation or polar
coordinate interpolation command was
issued during coordinate rotation by
program (G68).
P486 Milling error • Check the program.
• The milling command was issued during the
mirror image (when parameter or external
input is turned ON).
• Polar coordinate interpolation, cylindrical
interpolation or milling interpolation was
commanded during mirror image for facing
tool posts.
• The start command of the cylindrical
interpolation or polar coordinate
interpolation was issued during the normal
line control.
P511 Synchronization M code error • Check the program.
• Two or more synchronization M codes were
commanded in the same block.
• The synchronization M code and "!" code
were commanded in the same block.
• Synchronization with the M code was
commanded in 3rd part system or more.
(Synchronization with the M code is valid
only in 1st part system or 2nd part system.)
P550 No spec: G06.2(NURBS) • Check the specifications.
There is no NURBS interpolation option.
IV - 122
Appendix 6. Alarms
6.3 Program Error

P551 G06.2 knot error • Reconsider the program.
The knot (k) command value is smaller than • Specify the knot by monotone increment.
the value for the previous block.
P552 Start point of 1st G06.2 err • Match the G06.2 first block coordinate
The block end point immediately before the command value with the previous block end
G06.2 command and the G06.2 first block point.
command value do not match.
P554 Invld manual interrupt in G6.2 • Perform for blocks other than G06.2 mode
Manual interruption using a block was when manually interrupting.
performed while in G06.2 mode.
P555 Invalid restart during G06.2 • Restart from the block other than in G06.2
Restart was attempted from the block in mode.
G06.2 mode.
P600 No spec: Auto TLM • Check the specifications.
An automatic tool length measurement
command (G37) was execute though there
are no such command specifications.
P601 No spec: Skip • Check the specifications.
A skip command (G31) was issued though
there are no such command specifications.
P602 No spec: Multi skip • Check the specifications.
A multiple skip command (G31.1‚ G31.2 or
G31.3) was issued though there are no such
command specifications.
P603 Skip speed 0 • Specify the skip speed.
The skip speed is 0.
P604 TLM illegal axis • Specify only one axis.
No axis or more than one axis was specified
in the automatic tool length measurement
block.
P605 T & TLM command in a block • Specify this T code before the block.
The T code is in the same block as the
automatic tool length measurement block.
P606 T cmnd not found before TLM • Specify this T code before the block.
The T code was not yet specified in automatic
tool length measurement.
P607 TLM illegal signal • Check the program.
Before the area specified by the D command
or decelerating area parameter d‚ the
measurement position arrival signal went ON.
The signal remains OFF to the end.
P608 Skip during radius compen • Specify a radius compensation cancel (G40)
A skip command was specified during radius command or remove the skip command.
compensation processing.
P610 Illegal parameter • Check whether "#1549 Iv0vR1" to "#1553
• The parameter setting is not correct. Iv0vR5" are set in descending order (in order
• G114.1 was commanded when the spindle of large values).
synchronization with PLC I/F command was • Check whether "#1554 Iv0rd2" to "#1557
selected. Iv0rd5" are set in descending order.
• G113 was commanded when the • Check and correct "#1514 expLinax" and
spindle-spindle polygon machining option "#1515 expRotax".
was OFF and the spindle synchronization • Check the program.
with PLC I/F command was selected. • Check the parameter.
IV - 123
Appendix 6. Alarms
6.3 Program Error

P611 No spec: Exponential function • Check the specification.
Specification for exponential interpolation is
not available.
P612 Exponential function error • Check the program.
A movement command for exponential
interpolation was issued during mirror image
for facing tool posts.
P700 Illegal command value • Check the program.
Spindle synchronization was commanded to a • Check the parameter.
spindle that is not connected serially.
P900 No spec: Normal line control • Check the specifications.
A normal line control command (G40.1,
G41.1, G42.1) was issued when the normal
line control specifications were not provided.
P901 Normal line control axis G92 • Check the program.
A coordinate system preset command (G92)
was issued to a normal line control axis
during normal line control.
P902 Normal line control axis error • Correct the normal line control axis.
• The normal line control axis was set to a
linear axis.
• The normal line control axis was set to the
linear type rotary axis II axis.
• The normal line control axis has not been
set.
• The normal line control axis was the same
as the plane selection axis.
P903 Plane chg in Normal line ctrl • Delete the plane selection command (G17,
The plane selection command (G17, G18, G18, G19) from the program for normal line
G19) was issued during normal line control. control.
P920 No spec: 3D coord conv • Check the specifications.
There is no specification for 3-dimensional
coordinate conversion.
P921 Illegal G code at 3D coord • Refer to "Mitsubishi CNC 700/70 Series
A G code command that cannot be performed Programming Instruction Manual (Machining
was made during 3-dimensional coordinate Center Series)" for further details of usable G
conversion modal. commands.
• When the basic specification parameter
"#1229 set01/bit3" is ON, turn the parameter
OFF or specify the constant surface speed
control cancel (G97).
P922 Illegal mode at 3D coord • Refer to "Mitsubishi CNC 700/70 Series
A 3-dimensional coordinate conversion Programming Instruction Manual (Machining
command was issued during a modal for Center Series)" for further details of usable G
which 3-dimensional coordinate conversion commands.
P923 Illegal addr in 3D coord blk • Refer to "Mitsubishi CNC 700/70 Series
A G code for which G68 to combination could Programming Instruction Manual (Machining
not be performed was specified for the same Center Series)" for further details of usable G
block. commands.
IV - 124
Appendix 6. Alarms
6.3 Program Error

P930 No spec: Tool axis compen • Check the specifications.
A tool length compensation along the tool axis
command was issued even though there is no
tool length compensation along the tool axis
specification.
P931 Executing tool axis compen • Reconsider the program.
A G code that cannot be commanded exists
during tool length compensation along the
tool axis.
P932 Rot axis parameter error • Set the correct value and reboot.
There is a mistake in the linear axis name and
rotary axis name in the rotary axis
configuration parameters.
P940 No spec: Tool tip control • Check the specifications.
There is no tool tip center control
specification.
P941 Invalid T tip control command • Reconsider the program.
A tool tip center control command was issued
during a modal for which a tool tip center
control command cannot be issued.
P942 Invalid cmnd during T tip ctrl • Reconsider the program.
A G code that cannot be commanded was
issued during tool tip center control.
P943 Tool posture command illegal • Reconsider the program.
In the case of tool tip center control type 1, if
the signs at the tool-side rotary axis or table
base-side rotary axis start and finish points
differ, a tool base-side rotary axis or table
workpiece-side rotary axis rotation exists for
the same block, and does not pass a singular
point.
In the case of tool tip center control type 2,
the posture vector command is incorrect.
P990 PREPRO error • Reduce the number of commands that
Combining commands that required require pre-reading or delete such
pre-reading (nose R offset‚ corner commands.
chamfering/corner rounding‚ geometric I‚
geometric IB‚ and compound type fixed cycle
for turning machining) resulted in eight or
more pre-read blocks.
IV - 125
Appendix 7. G Code Guidance Display List

O: Modal, ×: Unmodal
G code Group Function Modal
00 01 Positioning O
01 01 Linear interpolation O
02 01 Circular interpolation CW (clockwise) O
03 01 Circular interpolation CCW (counterclockwise) O
02.1 01 Spiral interpolation CW (clockwise) O
03.1 01 Spiral interpolation CCW (counterclockwise) O
02.3 01 Exponential function interpolation positive rotation O
Exponential function interpolation negative
03.3 01 O
rotation
02.4 01 3-dimensional circular interpolation O
03.4 01 3-dimensional circular interpolation O
04 00 Dwell ×
05 00 High-speed machining mode I (P1) O
05 00 High-speed machining mode II (P2) O
05 00 High-speed high-accuracy control II (P10000) O
High-speed machining mode I
05 00 /High-speed machining mode II -
/High-speed high-accuracy control II OFF (P0)
05.1 00 High-speed high-accuracy control I (Q1) O
05.1 00 Fine spline mode (Q2) O
High-speed high-accuracy control I
05.1 00 -
/ Fine spline mode OFF (Q0)
06 - - -
06.2 01 NURBS interpolation O
07 - - -
07.1/107 21 Cylindrical interpolation O
08 00 High-accuracy control O
09 00 Exact stop check ×
10 00 Coordinate rotation by parameter input -
10 00 Program parameter input (L50) -
10 00 Program parameter input (L70) -
10 00 Tool compensation input (L10 to L13) -
10 00 Workpiece offset input (L2,L20) -
10 00 Tool life management data input (L3) -
Program parameter input / Tool compensation
11 00 input / Workpiece offset input / Inputting the tool -
life management data cancel
12 00 Circular cut CW (clockwise) ×
13 00 Circular cut CCW (counterclockwise) ×
12.1/112 21 Polar coordinate interpolation ON O
13.1/113 21 Polar coordinate interpolation cancel -
14 - - -
15 18 Polar coordinate command OFF -
16 18 Polar coordinate command ON O
17 02 Plane selection X-Y O
18 02 Plane selection Z-X O
19 02 Plane selection Y-Z O
20 06 Inch command O
21 06 Metric command O
22 00 Stroke check before travel ON -
23 00 Stroke check before travel OFF -
24 - - -
25 - - -
26 - - -
IV - 126
27 00 Reference point check ×
28 00 Reference point return ×
29 00 Start point return ×
30 00 2nd to 4th reference point return ×
30.1 00 Tool change position return 1 ×
31 00 Skip/Multi-step skip function 2 ×
31.1 00 Multi-step skip function 1-1 ×
32 - - -
33 01 Thread cutting O
34 00 Special fixed cycle (bolt hole circle) ×
35 00 Special fixed cycle (line at angle) ×
36 00 Special fixed cycle (arc) ×
37 00 Automatic tool length measurement ×
37.1 00 Special fixed cycle (grid) ×
38 00 Tool radius compensation vector designation ×
39 00 Tool radius compensation corner arc ×
40 07 Tool radius compensation cancel -
41 07 Tool radius compensation left O
42 07 Tool radius compensation right O
40.1 15 Normal line control cancel -
41.1 15 Normal line control left ON O
42.1 15 Normal line control right ON O
43 08 Tool length compensation (+) O
44 08 Tool length compensation (-) O
43.1 08 Tool length compensation along the tool axis O
43.4 08 Tool center point control type 1 O
43.5 08 Tool center point control type 2 O
45 00 Tool position compensation (expansion) ×
46 00 Tool position compensation (reduction) ×
47 00 Tool position compensation (doubled) ×
48 00 Tool position compensation (halved) ×
Tool length compensation cancel/Tool center point
49 08 -
control cancel
50 11 Scaling cancel -
51 11 Scaling ON O
50.1 19 G command mirror image cancel -
51.1 19 G command mirror image ON O
52 00 Local coordinate system setting O
53 00 Machine coordinate system selection ×
54 12 Work coordinate system 1 selection O
Work coordinate system selection 48 sets
54.1 12 O
expanded
IV - 127
60 00 Uni-directional positioning ×
61 13 Exact stop check mode O
61.1 13 High-accuracy control O
61.2 13 High-accuracy spline O
62 13 Automatic corner override O
63 13 Tapping mode O
63.1 13 Synchronous tapping mode (normal tapping) O
63.2 13 Synchronous tapping mode (reverse tapping) O
64 13 Cutting mode O
65 00 User macro call ×
66 14 User macro modal call A O
66.1 14 User macro modal call B O
67 14 User macro modal call cancel -
Programmable coordinate rotation mode ON
68 16 O
/3-dimensional coordinate conversion mode ON
Programmable coordinate rotation mode OFF
69 16 -
/3-dimensional coordinate conversion mode OFF
70 09 User fixed cycle -
73 09 Fixed cycle (step) O
74 09 Fixed cycle (reverse tap) O
75 09 Fixed cycle (circle cutting cycle) O
76 09 Fixed cycle (fine boring) O
80 09 Fixed cycle cancel -
81 09 Fixed cycle (drill/spot drill) O
82 09 Fixed cycle (drill/counter boring) O
83 09 Fixed cycle (deep drilling) O
84 09 Fixed cycle (tapping) O
85 09 Fixed cycle (boring) O
87 09 Fixed cycle (back boring) O
90 03 Absolute value command O
91 03 Incremental command value O
92 00 Machine coordinate system setting O
93 05 Inverse time feed O
94 05 Asynchronous feed (per-minute feed) O
95 05 Synchronous feed (per-revolution feed) O
96 17 Constant surface speed control ON O
97 17 Constant surface speed control OFF -
98 10 Fixed cycle Initial level return O
99 10 Fixed cycle R point level return O
100 to 225 00 User macro (G code call) Max. 10 -
IV - 128
Revision History
Date of revision Manual No. Revision details
Aug. 2004 IB(NA)1500042-A First edition created.
Mar. 2005 IB(NA)1500042-B • Contents were revised to correspond to Mitsubishi CNC 700 Series software version
B0.
• The following sections were added to "I. SCREEN OPERATIONS":
1.5 Setting Data
2.2.2 Changing Whether to Show or Hide the Comment Field
2.3.5 Operation Sequence for Program Restart
2.5.8 Switching Full-screen Display Mode
2.16.2 Setting the Time Display Selection
3.4.4 Erasing the Tool Registration Data
3.12 T Code List
4.2.17 G Code Guidance
6.6 Absolute Position Setting Screen
6.7 Auxiliary Axis Test Screen
• The following section names were changed:
"2.3.3 Directory change screen" -> "2.3.3 File Setting Screen"
"5.1 Hardware and software configuration screen (H/W S/W config screen)"
-> "5.1 System Configuration Screen "
• The following sections were unified.
"4.5.9 Formatting an FLD" and "4.5.10 Formatting a Memory card and DS"
-> "4.5.9 Formatting an External Device "
"6.2.9 Formatting an FLD" and "6.2.10 Formatting a Memory card and DS"
-> "6.2.9 Formatting an External Device "
• The configuration of "1. Operating the Setting and Display Unit" in "I. SCREEN
OPERATIONS" was changed.
• The following sections were added to " II. MACHINE OPERATIONS":
• "III. MAINTENANCE" was added.
• The following sections were added to " IV. APPENDIXES":
6.2.15 System setup-related operation messages
6.2.16 Automatic backup-related operation messages
• Mistakes were corrected.
Date of revision Manual No. Revision details
Sept. 2005 IB(NA)1500042-C • Contents were revised to correspond to Mitsubishi CNC 700 Series software version
B3.
1.8.2 Alarm Guidance
1.9 Touch Panel Functions
2.2.3 Changing the Sorting Method
3.3.1 Tool Measurement (M system)
3.3.2 Tool Measurement (L system)
3.7.4 Carrying Out Rotation Measurement
3.13 Pallet Program Registration
• The following section was added to " IV. APPENDIXES":
6.2.17 Messages Related to Anshin-net
• The following sections were changed to paragraph header:
3.3.1 Carrying Out Tool Length Measurement
3.3.2 Carrying Out Tool Radius Measurement
• The following sections were deleted:
6.1.2 Selecting the Parameter No.
6.1.6 Machine Parameters
Mar. 2006 IB(NA)1500042-D • Contents were revised to correspond to Mitsubishi CNC 700 Series software version
C0.
4.2.17 Adding Sequence No. (N No.) Automatically
4.2.19 Playback Editing
4.5.12 Program Display Lock C
5.6.1 Alarm History
Sept. 2006 IB(NA)1500042-E • Contents were revised to correspond to Mitsubishi CNC 700 Series software version
D0.
1.5.2 Inputting Operations
3.7.2 Workpiece Measurement (L System)
5.10 Machine Tool Builder Network System (MTB net) Screen
• The configuration of "3.2 Tool Measurement" was changed.
• The configuration of "3.7 Workpiece Measurement" was changed because
workpiece measurement (L system) is added.
Global service network
NORTH AMERICA FA Center CHINA FA Center
EUROPEAN FA Center KOREAN FA Center
ASEAN FA Center
HONG KONG FA Center
TAIWAN FA Center
North America FA Center (MITSUBISHI ELECTRIC AUTOMATION INC.) ASEAN FA Center (MITSUBISHI ELECTRIC ASIA PTE. LTD.)
Illinois CNC Service Center Singapore CNC Service Center
500 CORPORATE WOODS PARKWAY, VERNON HILLS, IL. 60061, U.S.A. 307 ALEXANDRA ROAD #05-01/02 MITSUBISHI ELECTRIC BUILDING SINGAPORE 159943
TEL: +1-847-478-2500 (Se FAX: +1-847-478-2650 (Se TEL: +65-6473-2308 FAX: +65-6476-7439
California CNC Service Center Thailand MITSUBISHI CNC Agent Service Center (F. A. TECH CO., LTD)
5665 PLAZA DRIVE, CYPRESS, CA. 90630, U.S.A. 898/19,20,21,22 S.V. CITY BUILDING OFFICE TOWER 1 FLOOR 12,14 RAMA III RD
TEL: +1-714-220-4796 FAX: +1-714-229-3818 BANGPONGPANG, YANNAWA, BANGKOK 10120. THAILAND
Georgia CNC Service Center TEL: +66-2-682-6522 FAX: +66-2-682-6020
2810 PREMIERE PARKWAY SUITE 400, DULUTH, GA., 30097, U.S.A. Malaysia MITSUBISHI CNC Agent Service Center
TEL: +1-678-258-4500 FAX:+1-678-258-4519 (FLEXIBLE AUTOMATION SYSTEM SDN. BHD.)
New Jersey CNC Service Center 60, JALAN USJ 10/1B 47620 UEP SUBANG JAYA SELANGOR DARUL EHSAN MALAYSIA
200 COTTONTAIL LANE SOMERSET, NJ. 08873, U.S.A. TEL: +60-3-5631-7605 FAX:+60-3-5631-7636
TEL: +1-732-560-4500 FAX: +1-732-560-4531 JOHOR MITSUBISHI CNC Agent Service Satellite
Michigan CNC Service Satellite (FLEXIBLE AUTOMATION SYSTEM SDN. BHD.)
2545 38TH STREET, ALLEGAN, MI., 49010, U.S.A. NO. 16, JALAN SHAHBANDAR 1, TAMAN UNGKU TUN AMINAH, 81300 SKUDAI, JOHOR MALAYSIA
TEL: +1-847-478-2500 FAX:+1-269-673-4092 TEL: +60-7-557-8218 FAX: +60-7-557-3404
Ohio CNC Service Satellite Indonesia MITSUBISHI CNC Agent Service Center
62 W. 500 S., ANDERSON, IN., 46013, U.S.A. (PT. AUTOTEKNINDO SUMBER MAKMUR)
TEL: +1-847-478-2608 FAX: +1-847-478-2690 WISMA NUSANTARA 14TH FLOOR JL. M.H. THAMRIN 59, JAKARTA 10350 INDONESIA
Texas CNC Service Satellite TEL: +62-21-3917-144 FAX: +62-21-3917-164
1000, NOLEN DRIVE SUITE 200, GRAPEVINE, TX. 76051, U.S.A. India MITSUBISHI CNC Agent Service Center (MESSUNG SALES & SERVICES PVT. LTD.)
TEL: +1-817-251-7468 FAX: +1-817-416-1439 B-36FF, PAVANA INDUSTRIAL PREMISES M.I.D.C., BHOASRI PUNE 411026, INDIA
Canada CNC Service Center TEL: +91-20-2711-9484 FAX: +91-20-2712-8115
4299 14TH AVENUE MARKHAM, ON. L3R OJ2, CANADA BANGALORE MITSUBISHI CNC Agent Service Satellite
TEL: +1-905-475-7728 FAX: +1-905-475-7935 (MESSUNG SALES & SERVICES PVT. LTD.)
Mexico CNC Service Center S 615, 6TH FLOOR, MANIPAL CENTER, BANGALORE 560001, INDIA
MARIANO ESCOBEDO 69 TLALNEPANTLA, 54030 EDO. DE MEXICO TEL: +91-80-509-2119 FAX: +91-80-532-0480
TEL: +52-55-9171-7662 FAX: +52-55-9171-7698 Delhi MITSUBISHI CNC Agent Parts Center (MESSUNG SALES & SERVICES PVT. LTD.)
Monterrey CNC Service Satellite 1197, SECTOR 15 PART-2, OFF DELHI-JAIPUR HIGHWAY BEHIND 32ND MILESTONE
ARGENTINA 3900, FRACC. LAS TORRES, MONTERREY, N.L., 64720, MEXICO GURGAON 122001, INDIA
TEL: +52-81-8365-4171 FAX: +52-81-8365-4171 TEL: +91-98-1024-8895 FAX:
Brazil MITSUBISHI CNC Agent Service Center Philippines MITSUBISHI CNC Agent Service Center
(AUTOMOTION IND. COM. IMP. E EXP. LTDA.) (FLEXIBLE AUTOMATION SYSTEM CORPORATION)
ACESSO JOSE SARTORELLI, KM 2.1 18550-000 BOITUVA – SP, BRAZIL UNIT No.411, ALABAMG CORPORATE CENTER KM 25. WEST SERVICE ROAD SOUTH
TEL: +55-15-3363-9900 FAX: +55-15-3363-9911 SUPERHIGHWAY, ALABAMG MUNTINLUPA METRO MANILA, PHILIPPINES 1771
TEL: +63-2-807-2416 FAX: +63-2-807-2417
European FA Center (MITSUBISHI ELECTRIC EUROPE B.V.) Vietnam MITSUBISHI CNC Agent Service Center (SA GIANG TECHNO CO., LTD)
47-49 HOANG SA ST. DAKAO WARD, DIST.1 HO CHI MINH CITY, VIETNAM
Germany CNC Service Center TEL: +84-8-910-4763 FAX:+84-8-910-2593
GOTHAER STRASSE 8, 40880 RATINGEN, GERMANY
TEL: +49-2102-486-0 FAX:+49-2102486-591
South Germany CNC Service Center China FA Center (MITSUBISHI ELECTRIC AUTOMATION (SHANGHAI) LTD.)
KURZE STRASSE. 40, 70794 FILDERSTADT-BONLANDEN, GERMANY China CNC Service Center
TEL: +49-711-3270-010 FAX: +49-711-3270-0141 2/F., BLOCK 5 BLDG.AUTOMATION INSTRUMENTATION PLAZA, 103 CAOBAO RD. SHANGHAI
France CNC Service Center 200233, CHINA
25, BOULEVARD DES BOUVETS, 92741 NANTERRE CEDEX FRANCE TEL: +86-21-6120-0808 FAX: +86-21-6494-0178
TEL: +33-1-41-02-83-13 FAX: +33-1-49-01-07-25 Shenyang CNC Service Center
Lyon CNC Service Satellite TEL: +86-24-2397-0184 FAX: +86-24-2397-0185
Beijing CNC Service Satellite
U.K CNC Service Center 9/F, OFFICE TOWER1, HENDERSON CENTER, 18 JIANGUOMENNEI DAJIE, DONGCHENG
TRAVELLERS LANE, HATFIELD, HERTFORDSHIRE, AL10 8XB, U.K. DISTRICT, BEIJING 100005, CHINA
TEL: +44-1707-282-846 FAX:-44-1707-278-992 TEL: +86-10-6518-8830 FAX:+86-10-6518-8030
Italy CNC Service Center China MITSUBISHI CNC Agent Service Center
ZONA INDUSTRIALE VIA ARCHIMEDE 35 20041 AGRATE BRIANZA, MILANO ITALY (BEIJING JIAYOU HIGHTECH TECHNOLOGY DEVELOPMENT CO.)
TEL: +39-039-60531-342 FAX: +39-039-6053-206 RM 709, HIGH TECHNOLOGY BUILDING NO.229 NORTH SI HUAN ZHONG ROAD, HAIDIAN
Spain CNC Service Satellite DISTRICT , BEIJING 100083, CHINA
CTRA. DE RUBI, 76-80 -APDO.420 08190 SAINT CUGAT DEL VALLES, BARCELONA SPAIN TEL: +86-10-8288-3030 FAX:+86-10-6518-8030
TEL: +34-935-65-2236 FAX: Tianjin CNC Service Satellite
Turkey MITSUBISHI CNC Agent Service Center RM909, TAIHONG TOWER, NO220 SHIZILIN STREET, HEBEI DISTRICT, TIANJIN, CHINA 300143
(GENEL TEKNIK SISTEMLER LTD. STI.) TEL: -86-22-2653-9090 FAX: +86-22-2635-9050
DARULACEZE CAD. FAMAS IS MERKEZI A BLOCK NO.43 KAT2 80270 OKMEYDANI Shenzhen CNC Service Satellite
ISTANBUL, TURKEY RM02, UNIT A, 13/F, TIANAN NATIONAL TOWER, RENMING SOUTH ROAD, SHENZHEN, CHINA
TEL: +90-212-320-1640 FAX: +90-212-320-1649 518005
Poland MITSUBISHI CNC Agent Service Center (MPL Technology Sp. z. o. o) TEL: +86-755-2515-6691 FAX:+86-755-8218-4776
UL SLICZNA 34, 31-444 KRAKOW, POLAND Changchun Service Satellite
TEL: +48-12-632-28-85 FAX: TEL: +86-431-50214546 FAX: +86-431-5021690
Wroclaw MITSUBISHI CNC Agent Service Satellite (MPL Technology Sp. z. o. o) Hong Kong CNC Service Center
UL KOBIERZYCKA 23, 52-315 WROCLAW, POLAND UNIT A, 25/F RYODEN INDUSTRIAL CENTRE, 26-38 TA CHUEN PING STREET, KWAI CHUNG, NEW
TEL: +48-71-333-77-53 FAX:+48-71-333-77-53 TERRITORIES, HONG KONG
Czech MITSUBISHI CNC Agent Service Center TEL: +852-2619-8588 FAX:+852-2784-1323
(AUTOCONT CONTROL SYSTEM S.R.O. )
NEMOCNICNI 12, 702 00 OSTRAVA 2 CZECH REPUBLIC Taiwan FA Center (MITSUBISHI ELECTRIC TAIWAN CO., LTD.)
TEL: +420-596-152-426 FAX: +420-596-152-112 Taichung CNC Service Center
NO.8-1, GONG YEH 16TH RD., TAICHUNG INDUSTIAL PARK TAICHUNG CITY, TAIWAN R.O.C.
TEL: +886-4-2359-0688 FAX:+886-4-2359-0689
Taipei CNC Service Satellite
TEL: +886-4-2359-0688 FAX:+886-4-2359-0689
Tainan CNC Service Satellite
TEL: +886-4-2359-0688 FAX: +886-4-2359-0689
Korean FA Center (MITSUBISHI ELECTRIC AUTOMATION KOREA CO., LTD.)

Korea CNC Service Center
1480-6, GAYANG-DONG, GANGSEO-GU SEOUL 157-200, KOREA
TEL: +82-2-3660-9631 FAX: +82-2-3664-8668
Notice
Every effort has been made to keep up with software and hardware revisions in the
contents described in this manual. However, please understand that in some
unavoidable cases simultaneous revision is not possible.
Please contact your Mitsubishi Electric dealer with any questions or comments
regarding the use of this product.
Duplication Prohibited
This manual may not be reproduced in any form, in part or in whole, without written
permission from Mitsubishi Electric Corporation.
© 2004-2006 MITSUBISHI ELECTRIC CORPORATION
ALL RIGHTS RESERVED.

Instruction Manual

Uploaded by

Copyright:

Available Formats

Instruction Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Instruction Manual

Uploaded by

Copyright:

Available Formats

Microsoft® and Windows® are either registered trademarks or trademarks of Microsoft

Corporation in the United States and/or other countries.

MELDAS is a registered trademark of Mitsubishi Electric Corporation.

Details described in this manual

Refer to the following documents.

When the user may be subject to imminent fatalities or major

When the user may be subject to fatalities or major injuries if

When the user may be subject to bodily injury or when physical

3. Items related to preparation before use

4. Items related to screen operation

5. Items related to programming

6. Items related to operation

7. Items related to faults and abnormalities

8. Items related to maintenance

1. Operating the Setting and Display Unit ........................................................................................1

II. MACHINE OPERATIONS

1. Operation State ...............................................................................................................................2

1. Operating the Setting and Display Unit

1.1 Setting Display Unit Appearance

(6) Particular keys

(7) Data correction keys

(9) SHIFT key

(12) INPUT key

(10) Cursor keys

There is the following type of keyboard, too.

(1) Function keys (6) Particular keys

(5) Data setting keys

(6) Particular keys (7) Data correction keys

(13) RESET key (12) INPUT key

(10) Cursor keys

The following keys are provided on the keyboard.

Key type Key Operation

1.2 Screen Configuration

(1) (2) (3) (4) (5) (6)

Display item Details

1.2.1 Operation Mode

Symbol Details Explanation

1.2.2 MDI Status

Symbol Details Character color Background color

1.2.3 Operation Status

1 HLD 2 HLD 3 HLD 4 BST

Symbol Details Character color Background color

(Example) Warning display

Character color Background color

1.2.5 Operation Messages

Character color Background color

The operation message can be reset by pressing any key.

1.3 Screen Transition Diagram

Sp-stby TipDisp All sp

Edit Check I/O

Refer to "4. Edit Screens"

Servo Spindle Power AUX Synchro

Refer to "5. Diagnosis Screens"

Mainte Param Input/

Open Open CC-Link CC-Link

1.4 Screen Selection Procedure

The menu display will differ according to the L

1.5 Setting Data

1.5.1 Setting Numerals and Alphabetic Characters

/ keys: Moves the cursor one character to the left or right.

INSERT key: Enters the insert mode.

DELETE key: Deletes the character in front of the cursor.

C·B key: Deletes all characters in the data setting area.