Drafts - Drafts - Drafts - Concrete - May 9, 2024

Hilti PROFIS Engineering 3.1.
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 1
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Drafts_Drafts_Concrete - May 9, 2024 Date: 7/22/2024
Fastening point:
Specifier's comments:
1 Anchor Design
1.1 Input data
Anchor type and diameter: HST4-R M12

Return period (service life in years): 50
Item number: 2329107 HST4-R M12x75 5-10
Filling set or any suitable annular gap filling solution
Specification text: Hilti HST4-R stud anchor with 40 mm
embedment, M12, Stainless steel, installation
per ETA-21/0878, with annular gaps filled with
Hilti Filling set or any suitable gap solutions
Effective embedment depth: hef,opti = 40.0 mm (hef,limit = 125.0 mm), hnom = 49.0 mm
Material: A4
Evaluation Service Report: ETA-21/0878
Issued I Valid: 2/28/2024 | -
Proof: SOFA based on EN 1992-4, Mechanical
Stand-off installation: eb = 0.0 mm (no stand-off); t = 8.0 mm
Anchor plate
CBFEM
: lx x ly x t = 240.0 mm x 90.0 mm x 8.0 mm;
Profile: Square bar, ; (L x W x T) = 60.0 mm x 60.0 mm

Base material: 2
cracked concrete, C35/45, fc,cyl = 35.00 N/mm ; h =250.0 mm, User-defined partial material safety
factor gc = 1.500
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: no reinforcement or reinforcement spacing >= 150 mm (any Ø) or >= 100 mm (Ø <= 10 mm)
no longitudinal edge reinforcement
CBFEM
- The anchor calculation is based on a component-based Finite Element Method (CBFEM)
Geometry [mm] & Loading [kN, kNm]
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2024 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
1
Hilti PROFIS Engineering 3.1.1
Company: Page: 2
Address: Specifier:
Fastening point:
1.1.1 Load combination

Case Description Forces [kN] / Moments [kNm] Seismic Fire Max. Util. Anchor [%]
1 Combination 1 N = -18.000; Vx = 6.000; Vy = 6.000; no no 74
Mx = 0.000; My = 0.000; Mz = 0.000;
1.2 Load case/Resulting anchor forces
Anchor reactions [kN]

Tension force: (+Tension, -Compression)
Anchor Tension force Shear force Shear force x Shear force y y
1 0.324 2.102 1.476 1.498 Compression
3 4
2 0.201 2.031 1.493 1.376 x
3 0.000 2.168 1.474 1.590 1 2
4 0.000 2.187 1.557 1.536 Tension
resulting tension force in (x/y)=(-20.3/-10.0): 0.525 [kN]

resulting compression force in (x/y)=(-0.8/2.0): 18.584 [kN]
Anchor forces are calculated based on a component-based Finite Element Method (CBFEM)
2
Company: Page: 3
Address: Specifier:
Fastening point:
1.3 Tension load (EN 1992-4, Section 7.2.1)
Load [kN] Capacity [kN] Utilization bN [%] Status

Steel Strength* 0.324 34.286 1 OK
Pullout Strength* 0.324 24.694 2 OK
Concrete Breakout Failure** 0.324 14.378 3 OK
Splitting failure** N/A N/A N/A N/A
* highest loaded anchor **anchor group (anchors in tension)
1.3.1 Steel Strength
N
NEd £ NRd,s = Rk,s EN 1992-4, Table 7.1
gM,s
NRk,s [kN] gM,s NRd,s [kN] NEd [kN]

48.000 1.400 34.286 0.324
1.3.2 Pullout Strength
y c · NRk,p
NEd £ NRd,p = EN 1992-4, Table 7.1
gM,p
NRk,p [kN] yc g M,p NRd,p [kN] NEd [kN]

28.000 1.323 1.500 24.694 0.324
3
Company: Page: 4
Address: Specifier:
Fastening point:
1.3.3 Concrete Breakout Failure
N
NEd £ NRd,c = Rk,c EN 1992-4, Table 7.1
gM,c
0 Ac,N
NRk,c = NRk,c · 0
· y s,N · y re,N · y ec1,N · y ec2,N · y M,N EN 1992-4, Eq. (7.1)
Ac,N
0 1,5
NRk,c = k1 · √fck · hef EN 1992-4, Eq. (7.2)
0
Ac,N = scr,N · scr,N EN 1992-4, Eq. (7.3)
c
y s,N = 0.7 + 0.3 · 1.00 EN 1992-4, Eq. (7.4)
ccr,N £
1
y ec1,N = 1.00 EN 1992-4, Eq. (7.6)
2 · eN,1 £
1+ (
scr,N )
1
y ec2,N = 1.00 EN 1992-4, Eq. (7.6)
2 · eN,2 £
1+ (
scr,N )
z
y M,N = 2.0 - 1.00 EN 1992-4, Eq. (7.7)
1.5 · hef ³
2 0 2 2
Ac,N [mm ] Ac,N [mm ] ccr,N [mm] scr,N [mm] fc,cyl [N/mm ]
14,400 14,400 60.0 120.0 35.00
ec1,N [mm] y ec1,N ec2,N [mm] y ec2,N y s,N y re,N

0.0 1.000 0.0 1.000 1.000 1.000
0
z [mm] y M,N k1 NRk,c [kN] gM,c NRd,c [kN] NEd [kN]
22.9 1.619 8.900 13.320 1.500 14.378 0.324
Group anchor ID
1
4
Company: Page: 5
Address: Specifier:
Fastening point:
1.4 Shear load (EN 1992-4, Section 7.2.2)
Load [kN] Capacity [kN] Utilization bV [%] Status

Steel Strength (without lever arm)* 2.187 27.488 8 OK
Steel failure (with lever arm)* N/A N/A N/A N/A
Pryout Strength** 8.485 60.064 15 OK
Concrete edge failure in direction x+** 6.156 8.344 74 OK
* highest loaded anchor **anchor group (relevant anchors)
1.4.1 Steel Strength (without lever arm)
V
VEd £ VRd,s = Rk,s EN 1992-4, Table 7.2
gM,s
0
VRk,s = k7 · VRk,s EN 1992-4, Eq. (7.35)
0
VRk,s [kN] k7 VRk,s [kN] gM,s VRd,s [kN] VEd [kN]
34.360 1.000 34.360 1.250 27.488 2.187
1.4.2 Pryout Strength
V
VEd £ VRd,cp = Rk,cp EN 1992-4, Table 7.2
gM,c,p
VRk,cp = k8 · NRk,c EN 1992-4, Eq. (7.39a)
0 A
NRk,c = NRk,c · c,N
0
· y s,N · y re,N · y ec1,N · y ec2,N · y M,N EN 1992-4, Eq. (7.1)
Ac,N
0 1,5
NRk,c = k1 · √fck · hef EN 1992-4, Eq. (7.2)
0
Ac,N = scr,N · scr,N EN 1992-4, Eq. (7.3)
c
y s,N = 0.7 + 0.3 · 1.00 EN 1992-4, Eq. (7.4)
ccr,N £
1
y ec1,N = £ 1.00 EN 1992-4, Eq. (7.6)
1+ ( 2 · eV,1
scr,N )
1
y ec2,N = £ 1.00 EN 1992-4, Eq. (7.6)
1+ ( 2 · eV,2
scr,N )
y M,N =1 EN 1992-4, Eq. (7.7)
2 0 2 2
Ac,N [mm ] Ac,N [mm ] ccr,N [mm] scr,N [mm] k8 fc,cyl [N/mm ]
40,600 14,400 60.0 120.0 2.500 35.00
ec1,V [mm] y ec1,N ec2,V [mm] y ec2,N y s,N y re,N y M,N

1.2 0.980 1.2 0.980 1.000 1.000 1.000
0
k1 NRk,c [kN] gM,c,p VRd,cp [kN] VEd [kN]
8.900 13.320 1.500 60.064 8.485
Group anchor ID
1-4
5
Company: Page: 6
Address: Specifier:
Fastening point:
1.4.3 Concrete edge failure in direction x+
V
VEd £ VRd,c = Rk,c EN 1992-4, Table 7.2
gM,c
0 Ac,V
VRk,c = kT · VRk,c · 0
· y s,V · y h,V · y a,V · y ec,V · y re,V EN 1992-4, Eq. (7.40)
Ac,V
0 a b 1,5
VRk,c = k9 · dnom · lf · √fck · c1 EN 1992-4, Eq. (7.41)
0,5
a = 0.1 · () lf
c1
EN 1992-4, Eq. (7.42)
0,2
= 0.1 · (
c )
d nom
b EN 1992-4, Eq. (7.43)
1
0 2
Ac,V = 4.5 · c1 EN 1992-4, Eq. (7.44)
c2
y s,V = 0.7 + 0.3 · 1.00 EN 1992-4, Eq. (7.45)
1.5 · c1 £
0,5
y h,V = (1.5h· c ) 1
³ 1.00 EN 1992-4, Eq. (7.46)
1
y ec,V = £ 1.00 EN 1992-4, Eq. (7.47)
1+ ( 2 · eV
3 · c1 )
y a,V = √(cos a ) + (10.5 · sin a )
V
2
V
2 ³ 1.00 EN 1992-4, Eq. (7.48)
lf [mm] dnom [mm] k9 a b 2

fc,cyl [N/mm ]
40.0 12.00 1.700 0.062 0.065 35.00
2 0 2
c1 [mm] Ac,V [mm ] Ac,V [mm ]
105.0 40,950 49,612
y s,V y h,V aV [°] y a,V ec,V [mm] y ec,V y re,V

0.929 1.000 12.92 1.019 0.0 1.000 1.000
0
VRk,c [kN] kT gM,c VRd,c [kN] VEd [kN]
16.021 1.0 1.500 8.344 6.156
6
Company: Page: 7
Address: Specifier:
Fastening point:
1.5 Combined tension and shear loads (EN 1992-4, Section 7.2.3)
Steel failure
bN bV a Utilization bN,V [%] Status

0.009 0.076 2.000 1 OK
a a
bN + bV £ 1.0
Concrete failure
bN bV a Utilization bN,V [%] Status

0.023 0.738 1.000 64 OK
(bN + bV) / 1.2 £ 1.0
1.6 Warnings
• The anchor design methods in PROFIS Engineering require rigid anchor plates as per current regulations (ETAG 001/Annex C, EOTA
TR029, etc.). This means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the anchor
plate is assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Engineering calculates
the minimum required anchor plate thickness with CBFEM to limit the stress of the anchor plate based on the assumptions explained above.
The proof if the rigid base plate assumption is valid is not carried out by PROFIS Engineering. Input data and results must be checked for
agreement with the existing conditions and for plausibility!
• Design is only valid if hole is filled to remove clearance, clearance as per EN 1992-4 Table 6.1
• Checking the transfer of loads into the base material is required in accordance with EN 1992-4, Annex A!
• The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 6.1 of EN 1992-4! For larger diameters
of the clearance hole see section 6.2.2 of EN 1992-4!
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to
be followed to ensure a proper installation.
• For the determination of the y re,v (concrete edge failure) the minimum concrete cover defined in the design settings is used as the concrete
cover of the edge reinforcement.
• The anchor design methods in PROFIS Engineering require rigid anchor plates, as per current regulations (AS 5216:2021, ETAG 001/Annex
C, EOTA TR029 etc.). This means that the anchor plate should be sufficiently rigid to prevent load re-distribution to the anchors due to
elastic/plastic displacements. The user accepts that the anchor plate is considered close to rigid by engineering judgment."
• The characteristic bond resistances depend on the return period (service life in years): 50
7
Company: Page: 8
Address: Specifier:
Fastening point:
1.7 Installation data

2 2
Anchor plate, steel: S 235; E = 210,000.00 N/mm ; fyk = 235.00 N/mm Anchor type and diameter: HST4-R M12
Profile: Square bar, ; (L x W x T) = 60.0 mm x 60.0 mm Item number: 2329107 HST4-R M12x75 5-10
Hole diameter in the fixture: df = 14.0 mm Maximum installation torque: 60 Nm
Plate thickness (input): 8.0 mm Hole diameter in the base material: 12.0 mm
Hole depth in the base material: 69.0 mm
Drilling method: Hammer drilled Minimum thickness of the base material: 101.0 mm
Cleaning: No cleaning of the drilled hole is required
Hilti HST4-R stud anchor with 40 mm embedment, M12, Stainless steel, installation per ETA-21/0878, with annular gaps filled with Hilti Filling
set or any suitable gap solutions
1.7.1 Recommended accessories
Drilling Cleaning Setting

• Suitable Rotary Hammer • No accessory required • Torque controlled cordless impact tool
• Properly sized drill bit • Torque wrench
• Hammer
y
120.0 120.0
35.0
45.0
3 4
20.0
x
1 2
45.0
35.0
25.0 50.0 95.0 50.0 20.0
Coordinates Anchor [mm]

Anchor x y c-x c+x c-y c+y
1 -95.0 -10.0 110.0 300.0 120.0 140.0
2 100.0 -10.0 305.0 105.0 120.0 140.0
3 -45.0 10.0 160.0 250.0 140.0 120.0
4 50.0 10.0 255.0 155.0 140.0 120.0
8
Company: Page: 9
Address: Specifier:
Fastening point:
2 Anchor plate rigidity check
2.1 Input data

Anchor plate: Shape: Rectangular
lx x ly x t = 240.0 mm x 90.0 mm x 8.0 mm
Calculation: Anchor Plate Rigidity Check
Material: S 235; Fy = 235.00 N/mm²; εlim = 5.00%
Anchor type and size: HST4-R M12, hef = 40.0 mm
Anchor stiffness: The anchor is modeled considering stiffness values determined from load displacement curves tested in an
independent laboratory. Please note that no simple replacement of the anchor is possible as the anchor
stiffness has a major impact on the load distribution results.
Design method: EN-based design using component-based FEM
Stand-off installation: eb = 0.0 mm (No stand-off); t = 8.0 mm
Profile: Custom; (L x W x T x FT) = 60.0 mm x 60.0 mm x - x -
Material: S 235; Fy = 215.00 N/mm²; εlim = 5.00%
Eccentricity x: 0.0 mm
Eccentricity y: 0.0 mm
Base material: Cracked concrete; C35/45; fc,cyl = 35.00 N/mm²; h = 250.0 mm; E = 34,000.00 N/mm²; G = 14,166.67
N/mm²; v = 0.20
Welds (profile to anchor plate): Type of redistribution: Plastic
Material: S 235
Mesh size: Number of elements on edge: 8
Min. size of element: 10.0 mm
Max. size of element: 50.0 mm
2.2 Anchor plate classification

Results below are displayed for the decisive load combinations: Combination 1
Anchor tension forces Equivalent rigid anchor plate (CBFEM) Component-based Finite Element Method
(CBFEM) anchor plate design
Anchor 1 0.000 kN 0.324 kN
Anchor 2 0.000 kN 0.201 kN
Anchor 3 0.000 kN 0.000 kN
Anchor 4 0.000 kN 0.000 kN
User accepted to consider the selected anchor plate as rigid by his/her engineering judgement. This means the anchor design guidelines can
be applied.
9
Company: Page: 10
Address: Specifier:
Fastening point:
2.3 Warnings
● By using the CBFEM calculation functionality of PROFIS Engineering you may act outside the applicable design codes and your specified
anchor plate may not behave rigid. Please, validate the results with a professional designer and/or structural engineer to ensure suitability
and adequacy for your specific jurisdiction and project requirements.
● The anchor is modeled considering stiffness values determined from load displacement curves tested in an independent laboratory.
Please note that no simple replacement of the anchor is possible as the anchor stiffness has a major impact on the load distribution
results.
10
Company: Page: 11
Address: Specifier:
Fastening point:
3 Summary of results
Load combination Max. utilization Status
Anchors Combination 1 74% OK
Fastening meets the design criteria!
11
Company: Page: 12
Address: Specifier:
Fastening point:
4 Remarks; Your Cooperation Duties

● Any and all information and data contained in the Software concern solely the use of Hilti products and are based on the principles,
formulas and security regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc.,
that must be strictly complied with by the user. All figures contained therein are average figures, and therefore use-specific tests are to be
conducted prior to using the relevant Hilti product. The results of the calculations carried out by means of the Software are based
essentially on the data you put in. Therefore, you bear the sole responsibility for the absence of errors, the completeness and the
relevance of the data to be put in by you. Moreover, you bear sole responsibility for having the results of the calculation checked and
cleared by an expert, particularly with regard to compliance with applicable norms and permits, prior to using them for your specific facility.
The Software serves only as an aid to interpret norms and permits without any guarantee as to the absence of errors, the correctness and
the relevance of the results or suitability for a specific application.
● You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for
the regular backup of programs and data and, if applicable, carry out the updates of the Software offered by Hilti on a regular basis. If you
do not use the AutoUpdate function of the Software, you must ensure that you are using the current and thus up-to-date version of the
Software in each case by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery
of lost or damaged data or programs, arising from a culpable breach of duty by you.
12

Drafts - Drafts - Drafts - Concrete - May 9, 2024

Uploaded by

Copyright:

Available Formats

Drafts - Drafts - Drafts - Concrete - May 9, 2024

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Drafts - Drafts - Drafts - Concrete - May 9, 2024

Uploaded by

Copyright:

Available Formats

Hilti PROFIS Engineering 3.1.

Anchor type and diameter: HST4-R M12

Profile: Square bar, ; (L x W x T) = 60.0 mm x 60.0 mm

Geometry [mm] & Loading [kN, kNm]

1.1.1 Load combination

1.2 Load case/Resulting anchor forces

Anchor reactions [kN]

resulting tension force in (x/y)=(-20.3/-10.0): 0.525 [kN]

1.3 Tension load (EN 1992-4, Section 7.2.1)

Load [kN] Capacity [kN] Utilization bN [%] Status

* highest loaded anchor **anchor group (anchors in tension)

1.3.1 Steel Strength

NRk,s [kN] gM,s NRd,s [kN] NEd [kN]

1.3.2 Pullout Strength

NRk,p [kN] yc g M,p NRd,p [kN] NEd [kN]

1.3.3 Concrete Breakout Failure

ec1,N [mm] y ec1,N ec2,N [mm] y ec2,N y s,N y re,N

1.4 Shear load (EN 1992-4, Section 7.2.2)

Load [kN] Capacity [kN] Utilization bV [%] Status

* highest loaded anchor **anchor group (relevant anchors)

1.4.1 Steel Strength (without lever arm)

1.4.2 Pryout Strength

ec1,V [mm] y ec1,N ec2,V [mm] y ec2,N y s,N y re,N y M,N

1.4.3 Concrete edge failure in direction x+

lf [mm] dnom [mm] k9 a b 2

y s,V y h,V aV [°] y a,V ec,V [mm] y ec,V y re,V

bN bV a Utilization bN,V [%] Status

bN bV a Utilization bN,V [%] Status

(bN + bV) / 1.2 £ 1.0

1.7 Installation data

1.7.1 Recommended accessories

Drilling Cleaning Setting

25.0 50.0 95.0 50.0 20.0

Coordinates Anchor [mm]

2 Anchor plate rigidity check

2.1 Input data

2.2 Anchor plate classification

Fastening meets the design criteria!

4 Remarks; Your Cooperation Duties

You might also like