Alfa Laval Pump Handbook

All you need to know ...
Alfa Laval in brief

Alfa Laval is a leading global
provider of specialized products
and engineering solutions.
Our equipment, systems and
services are dedicated to
assisting customers in optimizing
the performance of their
processes. Time and time again.
We help them heat, cool,
separate and transport products
such as oil, water, chemicals,
beverages, foodstuff, starch and
pharmaceuticals.
Our worldwide organization works
closely with customers in almost
Alfa Laval Pump Handbook

100 countries to help them stay Alfa Laval Pump Handbook
ahead.
How to contact Alfa Laval

Contact details for all countries
are continually updated on
our website. Please visit
www.alfalaval.com to access the
information.
PM66050GB1 2001
First edition 2001
The information provided in this handbook is given

in good faith, but Alfa Laval is not able to accept any
responsibility for the accuracy of its content, or any
consequences that may arise from the use of the
information supplied or materials described.
Inside view
This pump handbook has been produced to support pump users

at all levels, providing an invaluable reference tool. The handbook
includes all the necessary information for the correct selection
and successful application of the Alfa Laval ranges of Centrifugal,
Liquid Ring and Rotary Lobe Pumps. The handbook is divided
into fifteen main sections, which are as follows:
1 Introduction 9 Motors
2 Terminology and Theory 10 Cleaning Guidelines
3 Pump Selection 11 Compliance with International

Standards and Guidelines
4 Pump Description
12 Installation Guide
5 Pump Materials of Construction
13 Troubleshooting
6 Pump Sealing
14 Technical Data
7 Pump Sizing
15 Glossary of Terms
8 Pump Specification Options
Alfa Laval Pump Handbook 1

Contents
Section 1: Introduction Section 5: Pump Materials of Construction
Introduction of the Pump Handbook. 5 Description of the materials, both metallic and
elastomeric, that are used in the construction of
1.1 What is a Pump? 5 Alfa Laval pump ranges. 61
Section 2: Terminology and Theory 5.1 Main Components 61

Explanation of the terminology and theory of 5.2 Steel Surfaces 63
pumping applications, including rheology, 5.3 Elastomers 65
flow characteristics, pressure and NPSH. 7
Section 6: Pump Sealing
2.1 Product/Fluid Data 8 Explanation of pump sealing principles with illustrations
2.1.1 Rheology 8 of the different sealing arrangements used on
2.1.2 Viscosity 8 Alfa Laval pump ranges. A general seal selection guide is
2.1.3 Density 12 included, together with various operating parameters. 67
2.1.4 Specific Weight 12
2.1.5 Specific Gravity 13 6.1 Mechanical Seals - General 70
2.1.6 Temperature 13 6.2 Mechanical Seal Types
2.1.7 Flow Characteristics 13 in Alfa Laval Pump Ranges 80
2.1.8 Vapour Pressure 17 6.3 Other Sealing Options (Rotary Lobe Pumps only) 82
2.1.9 Fluids Containing Solids 17
2.2 Performance Data 18 Section 7: Pump Sizing
2.2.1 Capacity (Flow Rate) 18 How to size an Alfa Laval pump from product/fluid and
2.2.2 Pressure 18 performance data given, supported by relevant calculations
2.2.3 Cavitation 30 and worked examples with a simple step by step approach. 85
2.2.4 Net Positive Suction Head (NPSH) 31
2.2.5 Pressure ‘Shocks’ (Water Hammer) 35 7.1 General Information Required 85
7.2 Power 86
Section 3: Pump Selection 7.2.1 Hydraulic Power 86
Overview of the pump ranges currently available from 7.2.2 Required Power 87
Alfa Laval and which particular pumps to apply within 7.2.3 Torque 88
various application areas. 39 7.2.4 Efficiency 88
7.3 Centrifugal and Liquid Ring Pumps 92
3.1 General Applications Guide 40 7.3.1 Flow Curve 92
3.2 Pumps for Sanitary Applications 41 7.3.2 Flow Control 96
3.3 PumpCAS Selection and Configuration Tool 43 7.3.3 Alternative Pump Installations 100
7.4 Worked Examples
Section 4: Pump Description of Centrifugal Pump Sizing (Metric Units) 102
Description of Alfa Laval pump ranges including design, 7.4.1 Example 1 102
principle of operation and pump model types. 45 7.4.2 Example 2 106
7.5 Worked Examples
4.1 Centrifugal Pumps 45 of Centrifugal Pump Sizing (US Units) 109
4.1.1 General 45 7.5.1 Example 1 109
4.1.2 Principle of Operation 46 7.5.2 Example 2 113
4.1.3 Design 46 7.6 Rotary Lobe Pumps 116
4.1.4 Pump Range 48 7.6.1 Slip 116
4.2 Liquid Ring Pumps 52 7.6.2 Initial Suction Line Sizing 118
4.2.1 General 52 7.6.3 Performance Curve 119
4.2.2 Principle of Operation 52 7.6.4 Pumps fitted with Bi-lobe Rotors
4.2.3 Design 53 (Stainless Steel) 124
4.2.4 Pump Range 55 7.6.5 Pumps fitted with Bi-lobe Rotors
4.3 Rotary Lobe Pumps 56 (Non Galling Alloy) 125
4.3.1 General 56 7.6.6 Pumps fitted with Tri-lobe Rubber Covered Rotors 125
4.3.2 Principle of Operation 56 7.6.7 Pumps with Electropolished Surface Finish 126
4.3.3 Pump Range 57 7.6.8 Guidelines for Solids Handling 127
7.6.9 Guidelines for Pumping Shear Sensitive Media 128
7.7 Worked Examples of
Rotary Lobe Pump Sizing (Metric Units) 129
7.8 Worked Examples of
Rotary Lobe Pump Sizing (US Units) 143

Section 8: Pump Specifications Options 12.2 Flow Direction 201
Description of the various specification options available 12.2.1 Centrifugal Pumps 201
for the Alfa Laval pump ranges, such as port connections, 12.2.2 Rotary Lobe Pumps 202
heating/cooling jackets, pressure relief valves and other 12.3 Baseplates Foundation (Rotary Lobe Pumps only) 203
ancillaries. 157 12.4 Coupling Alignment (Rotary Lobe Pumps only) 204
12.5 Special Considerations for Liquid Ring Pumps 204
8.1 Centrifugal and Liquid Ring Pumps 157 12.5.1 Pipework 204
8.1.1 Port Connections 157
8.1.2 Heating/Cooling Jackets 158 Section 13: Troubleshooting
8.1.3 Pump Casing with Drain 159 Advises possible causes and solutions to most common
8.1.4 Increased Impeller Gap 159 problems found in pump installation and operation. 205
8.1.5 Pump Inlet Inducer 159
8.2 Rotary Lobe Pumps 160 13.1 General 205
8.2.1 Rotor Form 160 13.2 Common Problems 206
8.2.2 Clearances 162 13.2.1 Loss of Flow 206
8.2.3 Port Connections 164 13.2.2 Loss of Suction 206
8.2.4 Rectangular Inlets 165 13.2.3 Low Discharge Pressure 207
8.2.5 Heating/Cooling Jackets and Saddles 166 13.2.4 Excessive Noise or Vibration 207
8.2.6 Pump Overload Protection 167 13.2.5 Excessive Power 208
8.2.7 Ancillaries 169 13.2.6 Rapid Pump Wear 208
13.2.7 Seal Leakage 208
Section 9: Motors 13.3 Problem Solving Table 209
Description of electric motors, including information on motor
protection, methods of starting, motors for hazardous Section 14: Technical Data
environments and speed control. 173 Summary of the nomenclature and formulas used in this
handbook. Various conversion tables and charts are also
9.1 Output Power 175 shown. 213
9.2 Rated Speed 175
9.3 Voltage 176 14.1 Nomenclature 213
9.4 Cooling 176 14.2 Formulas 214
9.5 Insulation and Thermal Rating 176 14.3 Conversion Tables 219
9.6 Protection 177 14.3.1 Length 219
9.7 Methods of Starting 179 14.3.2 Volume 219
9.8 Motors for Hazardous Environments 180 14.3.3 Volumetric Capacity 219
9.9 Energy Efficient Motors 182 14.3.4 Mass Capacity 220
9.10 Speed Control 184 14.3.5 Pressure/Head 220
9.11 Changing Motor Nameplates 14.3.6 Force 220
- Centrifugal and Liquid Ring Pumps only 186 14.3.7 Torque 220
14.3.8 Power 221
Section 10: Cleaning Guidelines 14.3.9 Density 221
Advises cleaning guidelines for use in processes utilising 14.3.10 Viscosity Conversion Table 222
CIP (Clean In Place) systems. Interpretations of 14.3.11 Temperature Conversion Table 224
cleanliness are given and explanations of the cleaning 14.4 Water Vapour Pressure Table 225
cycle. 189 14.5 Pressure Drop Curve for 100 m ISO/DIN Tube 226
14.6 Velocity (m/s) in ISO and DIN Tubes
Section 11: Compliance with International at various Capacities 227
Standards and Guidelines 14.7 Equivalent Tube Length Table 228
Description of the international standards and guidelines 14.7.1 ISO Tube Metric 228
applicable to Alfa Laval pump ranges. 193 14.7.2 ISO Tube Feet 230
14.7.3 DIN Tube Metric 232
Section 12: Installation Guide 14.7.4 DIN Tube Feet 234
Advises guidelines relating to pump installation, 14.8 Moody Diagram 236
system design and pipework layout. 199 14.9 Initial Suction Line Sizing 237
14.10 Elastomer Compatibility Guide 238
12.1 General 199 14.11 Changing Motor Name Plates 243
12.1.1 System Design 199
12.1.2 Pipework 200 Section 15: Glossary of Terms
12.1.3 Weight 200 Explains the various terms found in this handbook. 249
12.1.4 Electrical Supply 200

...if pumps
are the
question
Alfa Laval is an acknowledged market
leader in pumping technology, supplying
Centrifugal and Positive Displacement
Pumps world-wide to various key
application areas such as food, brewery
and pharmaceutical.
Introduction
1. Introduction
This section gives a short introduction of the Pump Handbook.
1.1 What is a Pump?

There are many different definitions of this but at Alfa Laval we believe
this is best described as:
‘A machine used for the purpose of transferring quantities of

fluids and/or gases, from one place to another’.
This is illustrated below transferring fluid from tank A to spray

nozzles B.
Fig. 1.1a Typical pump installation
Pump types generally fall into two main categories - Rotodynamic

and Positive Displacement, of which there are many forms as shown
in Fig. 1.1b.
The Rotodynamic pump transfers rotating mechanical energy into

kinetic energy in the form of fluid velocity and pressure. The
Centrifugal and Liquid Ring pumps are types of rotodynamic pump,
which utilise centrifugal force to transfer the fluid being pumped.
The Rotary Lobe pump is a type of positive displacement pump,

which directly displaces the pumped fluid from pump inlet to outlet in
discrete volumes.

Introduction
Pumps
Positive Displacement Rotodynamic
Rotor Reciprocating Multi-Stage Single Stage
Multi-Rotor Single Rotor Diaphragm Plunger End Suction Double Entry
Screw Piston Simplex Process
Circumferential Piston Archimedian Screw Multiplex Rubber Lined
Gear Flexible Member Submersible
Internal External Peristaltic General
Vane Alfa Laval

Centrifugal
and
Rotary Lobe Progressing Cavity Liquid Ring
Alfa Laval
Rotary Lobe
Fig. 1.1b Pump classifications
6 Alfa Laval Pump Handbook

Terminology and Theory
2. Terminology and Theory

This section explains the terminology and theory of pumping
applications, including explanations of rheology, flow
characteristics, pressure and NPSH.
In order to select a pump two types of data are required:
• Product/Fluid data which includes viscosity, density/specific

gravity, temperature, flow characteristics, vapour pressure
and solids content.
• Performance data which includes capacity or flow rate, and
inlet/discharge pressure/head.
Different fluids have varying characteristics and are usually pumped

under different conditions. It is therefore very important to know all
relevant product and performance data before selecting a pump.

2.1 Product/Fluid Data

2.1.1 Rheology
The science of fluid flow is termed ‘Rheology’ and one of its most
important aspects is viscosity which is defined below.
2.1.2 Viscosity
The viscosity of a fluid can be regarded as a measure of how resistive
the fluid is to flow, it is comparable to the friction of solid bodies and
causes a retarding force. This retarding force transforms the kinetic
energy of the fluid into thermal energy.
The ease with which a fluid pours is an indication of its viscosity. For
example, cold oil has a high viscosity and pours very slowly, whereas
water has a relatively low viscosity and pours quite readily. High
viscosity fluids require greater shearing forces than low viscosity
fluids at a given shear rate. It follows therefore that viscosity affects
the magnitude of energy loss in a flowing fluid.
Two basic viscosity parameters are commonly used, absolute (or

dynamic) viscosity and kinematic viscosity.
Absolute (or Dynamic) Viscosity

This is a measure of how resistive the flow of a fluid is between two
layers of fluid in motion. A value can be obtained directly from a
rotational viscometer which measures the force needed to rotate a
spindle in the fluid. The SI unit of absolute viscosity is (mPa.s) in the
so-called MKS (metre, kilogram, second) system, while in the cgs
(centimetres, grams, seconds) system this is expressed as 1
centipoise (cP) where 1 mPa.s = 1 cP. Water at 1 atmosphere and
20°C (68oF) has the value of 1 mPa.s or 1 cP. Absolute viscosity is
usually designated by the symbol m.
Kinematic Viscosity
This is a measure of how resistive the flow of a fluid is under the
influence of gravity. Kinematic viscometers usually use the force of
gravity to cause the fluid to flow through a calibrated orifice, while
timing its flow. The SI unit of kinematic viscosity is (mm2/s) in the
so-called MKS (metre, kilogram, second) system, while in the cgs
(centimetres, grams, seconds) system this is expressed as 1
centistoke (cSt), where 1 mm2/s = 1 cSt. Water at 1 atmosphere and
20°C (68oF) has the value of 1 mm2/s = 1 cSt. Kinematic viscosity is
usually designated by the symbol n.

Relationship Between Absolute and Kinematic Viscosity

Absolute and Kinematic viscosity are related by:
n=m where r is the fluid density (see 2.1.3).

r
In the cgs system this translates to:
Kinematic Viscosity (cSt) = Absolute Viscosity (cP)

Specific Gravity
or
Absolute Viscosity (cP) = Kinematic Viscosity (cSt) x SG
A viscosity conversion table is included in 14.3.10.
Viscosity Variation with Temperature

Temperature can have a significant effect on viscosity and a viscosity
figure given for pump selection purposes without fluid temperature is
Viscosity
often meaningless - viscosity should always be quoted at the

pumping temperature. Generally viscosity falls with increasing
temperature and more significantly, it increases with falling
temperature. In a pumping system it can be advantageous to
Temperature
increase the temperature of a highly viscous fluid to ease flow.
Fig. 2.1.2a Viscosity variation
with temperature
Newtonian Fluids
In some fluids the viscosity is constant regardless of the shear forces
applied to the layers of fluid. These fluids are named Newtonian fluids.
Viscosity
At a constant temperature the viscosity is constant with change in

shear rate or agitation.
Typical fluids are:

Shear rate
• Water • Beer • Hydrocarbons • Milk • Mineral Oils • Resins • Syrups
Fig. 2.1.2b Newtonian Fluids

It is not always obvious which Non-Newtonian Fluids

type of viscous behaviour a Most empirical and test data for pumps and piping systems has been
fluid will exhibit and developed using Newtonian fluids across a wide range of viscosities.
consideration must be given However, there are many fluids which do not follow this linear law,
to the shear rate that will exist these fluids are named Non-Newtonian fluids.
in the pump under pumping
conditions. It is not unusual to When working with Non-Newtonian fluids we use Effective Viscosity
find the effective viscosity as to represent the viscous characteristics of the fluid as though it was
little as 1% of the value newtonian at that given set of conditions (shear rate, temperature).
measured by standard This effective viscosity is then used in calculations, charts, graphs and
instruments. ‘handbook’ information.
Viscosity
?
Viscosity
? Shear
Rate
Normal Typical Shear
Viscometer Rate in Pumping
Shear rate Reading System
Fig. 2.1.2c Viscosity against shear rate Fig. 2.1.2d Viscosity against shear rate
Types of Non-Newtonian Fluids

There are a number of different type of non-newtonian fluids each with
different characteristics. Effective viscosity at set conditions will be
different depending on the fluid being pumped. This can be better
understood by looking at the behaviour of viscous fluids with changes
in shear rate as follows.
Psuedoplastic Fluids
Viscosity decreases as shear rate increases, but initial viscosity may
be so high as to prevent start of flow in a normal pumping system.
Viscosity
Typical fluids are:

• Blood • Emulsions • Gums • Lotions • Soap • Toothpaste • Yeast
Shear rate
Fig. 2.1.2e Psuedoplastic Fluids

Dilatant Fluids
Viscosity increases as shear rate increases.
Typical fluids are:

Viscosity
• Clay Slurries • Paper Coatings
Shear rate
Fig. 2.1.2f Dilatant Fluids

Thixotropic Fluids
Viscosity decreases with time under shear conditions. After shear
ceases the viscosity will return to its original value - the time for
recovery will vary with different fluids.
Viscosity
Typical fluids are:

• Cosmetic Creams • Dairy Creams • Greases • Stabilised Yoghurt
Time
Fig. 2.1.2g Thixotropic Fluids
Anti-thixotropic Fluids
Viscosity increases with time under shear conditions. After shear
ceases the viscosity will return to its original value - the time for
Viscosity
recovery will vary with different fluids. As the name suggests

anti-thixotropic fluids have opposite rheological characteristics to
thixotropic fluids.
Time
Typical fluids are:
Fig. 2.1.2h Anti-thixotropic Fluids • Vanadium Pentoxide Solution
Rheomalactic Fluids
Viscosity decreases with time under shear conditions but does not
recover. Fluid structure is irreversibly destroyed.
Viscosity
Typical fluids are:

• Natural Rubber Latex • Natural Yoghurt
Time
Fig. 2.1.2i Rheomalactic Fluids
Plastic Fluids
Need a certain applied force (or yield stress) to overcome ‘solid-like
structure’, before flowing like a fluid.
Y
Stress
Where Y = Yield Stress

Typical fluids are:
• Barium X-ray Meal • Chocolate • Tomato Ketchup
Shear rate
Fig. 2.1.2j Plastic Fluids
It should be noted that some

fluids would have both
thixotropic and pseudoplastic
behaviour.

Density in gases varies 2.1.3 Density

considerably with pressure The density of a fluid is its mass per unit of volume, usually expressed
and temperature but can be as kilograms per cubic metre (kg/m3) or pounds per cubic foot (lb/ft3).
regarded as constant in fluids. Density is usually designated by the symbol r.
1 m³ of ethyl alcohol has a mass of 789 kg.

i.e. Density = 0.789 kg/m3.
1 ft³ of ethyl alcohol has a mass of 49.2 lb.

i.e. Density = 49.2 lb/ft3.
1 m 1 ft
m ft
1 1
Mass of Mass of
ethyl alcohol ethyl alcohol
1 m
1 ft
789 kg 49.2lb
Fig. 2.1.3a Density
2.1.4 Specific Weight

The specific weight of a fluid is its weight per unit volume and is
usually designated by the symbol g. It is related to density as follows:
g =rxg where g is gravity.
The units of weight per unit volume are N/m3 or lbf/ft3.
Standard gravity is as follows: g = 9.807 m/s2

g = 32.174 ft/s2
The specific weight of water at 20oC (68oF) and 1 atmosphere is as

follows:
g =9790 N/m3 = 62.4 lbf/ft3
Note! - Mass should not be confused with weight. Weight is the

force produced from gravity acting on the mass.

2.1.5 Specific Gravity

1 m 1 m
1
m
1
m The specific gravity of a fluid is the ratio of its density to the density of
water. As this is a ratio, it does not have any units of measure.
Mass of Mass of
ethyl alcohol water
1 m
1 m
789 kg 1000 kg 1 m³ of ethyl alcohol has a mass of 789 kg - its density is 789 kg/m³.
1 m³ of water has a mass of 1000 kg - its density is 1000 kg/m³.
Fig. 2.1.5a Specific gravity Specific Gravity of ethyl alcohol is: 789 kg/m³ = 0.789
1000 kg/m³
or
1 ft³ of ethyl alcohol has a mass of 49.2 lb - its density is 49.2 lb/ft³.
1 ft³ of water has a mass of 62.4 lb - its density is 62.4 lb/ft³.
Specific Gravity of ethyl alcohol is: 49.2 lb/ft³ = 0.789

62.4 lb/ft³
This resultant figure is dimensionless so the Specific Gravity (or SG) is

0.789.
Temperature is a measure of 2.1.6 Temperature

the internal energy level in a The temperature of the fluid at the pump inlet is usually of most
fluid, usually expressed in concern as vapour pressure can have a significant effect on pump
units of degrees Centigrade performance (see 2.1.8). Other fluid properties such as viscosity and
(°C) or degrees Fahrenheit (°F). density can also be affected by temperature changes. Thus a cooling
of the product in the discharge line could have a significant effect on
the pumping of a fluid.
The temperature of a fluid can also have a significant affect on the

selection of any elastomeric materials used.
A temperature conversion table is given in section 14.3.11.
2.1.7 Flow Characteristics

When considering a fluid flowing in a pipework system it is important
to be able to determine the type of flow. The connection between the
velocity and the capacity of a fluid (similar to water) in different tube
sizes is shown in table 14.6.
Under some conditions the fluid will appear to flow as layers in a

smooth and regular manner. This can be illustrated by opening a
water tap slowly until the flow is smooth and steady. This type of flow
is called laminar flow. If the water tap is opened wider, allowing the
velocity of flow to increase, a point will be reached whereby the

stream of water is no longer smooth and regular, but appears to be

moving in a chaotic manner. This type of flow is called turbulent flow.
The type of flow is indicated by the Reynolds number.
Velocity
Velocity is the distance a fluid moves per unit of time and is given by
equation as follows:
In dimensionally consistent SI units
Velocity V =Q where V = fluid velocity (m/s)

A Q = capacity (m³/s)
A = tube cross sectional area (m²)
Other convenient forms of this equation are:
Velocity V = Q x 353.6 where V = fluid velocity (m/s)

D² Q = capacity (m³/h)
D = tube diameter (mm)
or
Velocity V = Q x 0.409 where V = fluid velocity (ft/s)

D² Q = capacity (US gall/min)
D = tube diameter (in)
or
Velocity V = Q x 0.489 where V = fluid velocity (ft/s)

D² Q = capacity (UK gall/min)
Fluid velocity can be of great importance especially when pumping

slurries and fluids containing solids. In these instances, a certain
velocity may be required to prevent solids from settling in the
pipework, which could result in blockages and changes in system
pressure as the actual internal diameter of the pipe is effectively
decreased, which could impact on pump performance.

Laminar Flow
This is sometimes known as streamline, viscous or steady flow. The
fluid moves through the pipe in concentric layers with the maximum
velocity in the centre of the pipe, decreasing to zero at the pipe wall.
The velocity profile is parabolic, the gradient of which depends upon
the viscosity of the fluid for a set flow-rate.
V = velocity
u
max = maximum velocity
Fig. 2.1.7a Laminar flow
Turbulent Flow
This is sometimes known as unsteady flow with considerable mixing
taking place across the pipe cross section. The velocity profile is
more flattened than in laminar flow but remains fairly constant across
the section as shown in fig. 2.1.7b. Turbulent flow generally appears
at relatively high velocities and/or relatively low viscosities.
V = velocity
u
max = maximum velocity
Fig. 2.1.7b Turbulent flow

Transitional Flow
Between laminar and turbulent flow there is an area referred to as
transitional flow where conditions are unstable and have a blend of
each characteristic.
This is a ratio of inertia forces Reynolds Number (Re)

to viscous forces, and as such, Reynolds number for pipe flow is given by equation as follows:
a useful value for determining
whether flow will be laminar or In dimensionally consistent SI units
turbulent.
Re = DxVxr where D = tube diameter (m)
m V = fluid velocity (m/s)
r = density (kg/m³)
m = absolute viscosity (Pa.s)

Re = DxVxr where D = tube diameter (mm)

m V = fluid velocity (m/s)
m = absolute viscosity (cP)
or
Re = 21230 x Q where D = tube diameter (mm)

Dxm Q = capacity (l/min)
or
Re = 3162 x Q where D = tube diameter (in)

Dxn Q = capacity (US gall/min)
n = kinematic viscosity (cSt)
or
Re = 3800 x Q where D = tube diameter (in)

Dxn Q = capacity (UK gall/min)
Since Reynolds number is a ratio of two forces, it has no units. For a

given set of flow conditions, the Reynolds number will not vary when
using different units. It is important to use the same set of units, such
as above, when calculating Reynolds numbers.
Re less than 2300 - Laminar Flow

(Viscous force dominates - high
system losses)
Re in range 2300 to 4000 - Transitional Flow
(Critically balanced forces)
Re greater than 4000 - Turbulent Flow
(Inertia force dominates - low
system losses)
Where transitional flow occurs, frictional loss calculations should be

carried out for both laminar and turbulent conditions, and the highest
resulting loss used in subsequent system calculations.

2.1.8 Vapour Pressure

Fluids will evaporate unless prevented from doing so by external
pressure. The vapour pressure of a fluid is the pressure (at a given
Fluid (liquid form)
temperature) at which a fluid will change to a vapour and is expressed
as absolute pressure (bar a or psia) - see 2.2.2. Each fluid has its own
vapour pressure/temperature relationship. In pump sizing, vapour
Pvp = Vapour pressure (external
pressure can be a key factor in checking the Net Positive Suction
pressure required to maintain as a fluid)
Head (NPSH) available from the system (see 2.2.4).
Fig. 2.1.8a Vapour pressure
Temperature Vapour pressure (bar)

0 C (32 F)
o o
0.006 bar a (0.087 psia)
20o C (68o F) 0.023 bar a (0.334 psia)
100o C (212o F) 1.013 bar a (14.7 psia)
Water will boil (vaporise) at a temperature of:

- 0° C (32o F) if Pvp = 0.006 bar a (0.087 psia).
- 20° C (68o F) if Pvp = 0.023 bar a (0.334 psia).
- 100° C (212o F) if Pvp = 1.013 bar a (14.7 psia)
(atmospheric conditions at sea level).
In general terms Pvp:

- Is dependent upon the type of fluid.
- Increases at higher temperature.
- Is of great importance to pump inlet conditions.
- Should be determined from relevant tables.
The Pvp for water at various temperatures is shown in section 14.4.
2.1.9 Fluids Containing Solids

It is important to know if a fluid contains any particulate matter and if
so, the size and concentration. Special attention should be given
regarding any abrasive solids with respect to pump type and
construction, operating speed and shaft seals.
Size of solids is also important, as when pumping large particles the

pump inlet should be large enough for solids to enter the pump
without ‘bridging’ the pump inlet. Also the pump should be sized so
the cavity created in the pump chamber by the pump elements is of
sufficient size to allow satisfactory pump operation.
Concentration is normally expressed as a percentage by weight

(W/W) or volume (V/V) or a combination of both weight and volume
(W/V).

2.2 Performance Data

2.2.1 Capacity (Flow Rate)
The capacity (or flow rate) is the volume of fluid or mass that passes a
certain area per time unit. This is usually a known value dependent on
the actual process. For fluids the most common units of capacity are
litres per hour (l/h), cubic metres per hour (m³/h) and UK or US gallons
per minute (gall/min). For mass the most common units of capacity
are kilogram per hour (kg/h), tonne per hour (t/h) and pounds per hour
(lb/h).
2.2.2 Pressure
F = Force Pressure is defined as force per unit area: P= F
A
where F is the force perpendicular to a surface and A is the area of the

surface.
A
1 1
In the SI system the standard unit of force is the Newton (N) and area
Fig. 2.2.2a Pressure is given in square metres (m²). Pressure is expressed in units of
Newtons per square metre (N/m²). This derived unit is called the
Pascal (Pa). In practice Pascals are rarely used and the most
common units of force are bar, pounds per square inch (lb/in²) or psi,
and kilogram per square centimetre (kg/cm²).
Conversion factors between units of pressure are given in section

14.3.5.
Different Types of Pressure

For calculations involving fluid pressures, the measurements must be
relative to some reference pressure. Normally the reference is that of
the atmosphere and the resulting measured pressure is called gauge
pressure. Pressure measured relative to a perfect vacuum is called
‘absolute pressure’.
Atmospheric Pressure
The actual magnitude of the atmospheric pressure varies with
location and with climatic conditions. The range of normal variation of
atmospheric pressure near the earth’s surface is approximately 0.95
to 1.05 bar absolute (bar a) or 13.96 to 15.43 psi gauge (psig). At
sea level the standard atmospheric pressure is 1.013 bar a or 14.7
psi absolute (bar a or psia).

Gauge Pressure
Using atmospheric pressure as a zero reference, gauge pressure is
the pressure within the gauge that exceeds the surrounding
atmospheric pressure. It is a measure of the force per unit area
exerted by a fluid, commonly indicated in units of barg (bar gauge) or
psig (psi gauge).
Absolute Pressure
Is the total pressure exerted by a fluid. It equals atmospheric
pressure plus gauge pressure, indicated in units of bar a (bar
absolute) or psia (psi absolute).
Absolute Pressure = Gauge Pressure + Atmospheric Pressure
Vacuum
This is a commonly used term to describe pressure in a pumping
system below normal atmospheric pressure. This is a measure of the
difference between the measured pressure and atmospheric pressure
expressed in units of mercury (Hg) or units of psia.
0 psia = 760 mm Hg (29.9 in Hg).

14.7 psia = 0 mm Hg (0 in Hg).
Inlet (Suction) Pressure

This is the pressure at which the fluid is entering the pump. The
reading should be taken whilst the pump is running and as close to
the pump inlet as possible. This is expressed in units of absolute bar a
(psia) or gauge bar g (psig) depending upon the inlet conditions.
Outlet (Discharge) Pressure

This is the pressure at which the fluid leaves the pump. Again this
reading should be taken whilst the pump is running and as close to
the pump outlet as possible. The reading is expressed in units of
gauge bar (psig).
Differential Pressure
This is the difference between the inlet and outlet pressures. For inlet
pressures above atmospheric pressure the differential pressure is
obtained by subtracting the inlet pressure from the outlet pressure.
For inlet pressures below atmospheric pressure the differential
pressure is obtained by adding the inlet pressure to the outlet
pressure. It is therefore the total pressure reading and is the pressure
against which the pump will have to operate. Power requirements are
to be calculated on the basis of differential pressure.

Example: Inlet Pressure above Atmospheric Pressure
Outlet Inlet Differential
4 bar g 5.013 bar a

(58 psi g) (72.7 psi a)
1.5 bar g
(21.75 psi g)
0 bar g 1.013 bar a 0 bar g 1.013 bar a - =
(0 psi g) (14.7 psi a) (0 psi g) (14.7 psi a)
Differential = 4 - 1.5 = 2.5 bar
0 bar a or
(0 psi a)
= 58 - 21.75 = 36.25 psi
Example: Inlet Pressure below Atmospheric Pressure
Outlet Inlet Differential
4 bar g 5.013 bar a

(58 psi g) (72.7 psi a)
0 bar g 1.013 bar a 0 bar g 1.013 bar a (14.7

(0 psi g) (14.7 psi a) (0 psi g) psi a) + =
0.5 bar a
(7.25 psi a)
0 bar a 0 bar a
(0 psi a) (0 psi a) Differential = 4 + (1.013 - 0.5) = 4.513 bar
or
= 58 + (14.7 -7.25) = 65.45 psi
Fig. 2.2.2b Differential pressure

The relationship of elevation The Relationship Between Pressure and Elevation

equivalent to pressure is In a static fluid (a body of fluid at rest) the pressure difference between
commonly referred to as any two points is in direct proportion only to the vertical distance
‘head’. between the points. The same vertical height will give the same
pressure regardless of the pipe configuration in between.
Fig. 2.2.2c Relationship of pressure to
elevation
This pressure difference is due to the weight of a ‘column’ of fluid and

can be calculated as follows:
In dimensionally consistent SI units
Static Pressure (P) = r x g x h where P = Pressure/head (Pa)

r = density of fluid (kg/m3)
g = gravity (m/s2)
h = height of fluid (m)
Static Pressure (P) = h (m) x SG (bar)

10
or
Static Pressure (P) = h (ft) x SG (psi)

2.31

A pump capable of delivering 35 m (115 ft) head will produce different

pressures for fluids of differing specific gravities.
Water Slurry Solvent
35 m 35 m 35 m
(115ft). (115ft) (115ft)
3.5 bar 4.9 bar 2.5 bar

SG 1.0 (50 psi) SG 1.4 (70 psi) SG 0.7 (35 psi)
Fig. 2.2.2d Relationship of elevation to pressure
A pump capable of delivering 3.5 bar (50 psi) pressure will develop
different amounts of head for fluids of differing specific gravities.
Water Slurry Solvent
35 m 25 m 50 m
(115 ft). (82 ft). (165 ft).
3.5 bar 3.5 bar 3.5 bar

SG 1.0 (50 psi) SG 1.4 (50 psi) SG 0.7 (50 psi)
Fig. 2.2.2e Relationship of elevation to pressure
Below are terms commonly used to express different conditions in a

pumping system which can be expressed as pressure units (bar or
psi) or head units (m or ft).
Flooded Suction
This term is generally used to describe a positive inlet pressure/head,
whereby fluid will readily flow into the pump inlet at sufficient pressure
to avoid cavitation (see 2.2.3).
Static Head
The static head is a difference in fluid levels.
Static Suction Head

This is the difference in height between the fluid level and the centre
line of the pump inlet on the inlet side of the pump.
Static Discharge Head

This is the difference in height between the fluid level and the centre
line of the pump inlet on the discharge side of the pump.

Total Static Head

The total static head of a system is the difference in height between
the static discharge head and the static suction head.
Friction Head
This is the pressure drop on both inlet and discharge sides of the
pump due to frictional losses in fluid flow.
Dynamic Head
This is the energy required to set the fluid in motion and to overcome
any resistance to that motion.
Total Suction Head

The total suction head is the static suction head less the dynamic
head. Where the static head is negative, or where the dynamic head is
greater than the static head, this implies the fluid level will be below
the centre line of the pump inlet (ie suction lift).
Total Discharge Head

The total discharge head is the sum of the static discharge and
dynamic heads.
Total Head
Total head is the total pressure difference between the total discharge
head and the total suction head of the pump.The head is often a
known value. It can be calculated by means of different formulas if the
installation conditions are specified.
Total head H = Ht - (± Hs)
Total discharge head Ht = ht + hft + pt
Total suction head Hs = hs - hfs + (± ps)
Where: H = Total head.

Hs = Total suction head.
Ht = Total discharge head.
hs = Static suction head.
ht = Static discharge head.
hfs = Pressure drop in suction line.
hft = Pressure drop in discharge line.
Ps = Vacuum or pressure in a tank on suction side.
Pt = Pressure in a tank on discharge side.

In general terms: p > 0 for pressure.

p < 0 for vacuum.
p = 0 for open tank.
hs > 0 for flooded suction.
hs < 0 for suction lift.
Fig. 2.2.2f Flooded suction and open Fig. 2.2.2g Flooded suction and closed
discharge tanks discharge tanks
Fig. 2.2.2h Suction lift and open Fig. 2.2.2i Suction lift and closed
discharge tanks discharge tanks
Pressure drop is the result of Pressure Drop

frictional losses in pipework, Manufacturers of processing equipment, heat exchangers, static
fittings and other process mixers etc, usually have data available for pressure drop. These
equipment etc. losses are affected by fluid velocity, viscosity, tube diameter, internal
surface finish of tube and tube length.
The different losses and consequently the total pressure drop in the
process are, if necessary, determined in practice by converting the
losses into equivalent straight length of tube which can then be used
in subsequent system calculations.
For calculations on water like viscosity fluids, the pressure drop can
be determined referring to the Pressure Drop Curve (see 14.5) as
shown in Example 1. For higher viscosity fluids, a viscosity correction
factor is applied to the tube fittings by multiplying the resultant
equivalent tube length by the figures shown below - see Example 2.
Table 2.2.2a Viscosity - cP 1 - 100 101 - 2000 2001 - 20000 20001 - 100000
Correction Factor 1.0 0.75 0.5 0.25

Example 1: Process:
Pumping milk from tank A to tank G.
Q = 8 m3/h (35 US gall/min).
Tubes, valves and fittings:

A: Tank outlet dia. 63.5 mm (2.5 in).
A-B: 4 m (13 ft) tube dia. 63.5 mm (2.5 in).
C
A-B: 1 off bend 90 deg. dia. 63.5 mm (2.5 in).
B-C: 20 m (66 ft) tube dia. 51 mm (2 in).
Fig. 2.2.2j Example C: Seat valve type SRC-W-51-21-100.
C-E: 15 m (49 ft) tube dia. 51 mm (2 in).
B-E: 3 off bend 90 deg. dia. 51 mm (2 in).
D: Non-return valve type LKC-2, 51 mm (2 in).
E: Seat valve type SRC-W-51-21-100.
E-F: 46 m (151 ft) tube dia. 38 mm (1.5 in).
E-F: 4 off bend 90 deg. dia. 38 mm (1.5 in).
F: Seat valve type SRC-W-38-21-100.
The pressure drop through the tubes, valves and fittings is

determined as equivalent tube length, so that the total pressure drop
can be calculated.
The conversion into equivalent tube length is carried out by reference

to section 14.7. This results in the following equivalent tube length for
the different equipment as shown in the following tables:
Table 2.2.2b
Equipment Equivalent ISO Tube Length (m)
38 mm 51 mm 63.5 mm
A Tank outlet 1 (estimated)

A-B Tube 4
A-B Bend 90 deg. 1x1
B-C Tube 20
C-E Tube 15
C-E SRC seat valve, pos 3 10
B-E Bend 90 deg. 3x1
D LKC-2 non-return valve 12
E SRC, seat valve, pos.5 14
E-F Tube 46
E-F Bend 90 deg. 4x1
F SRC seat valve, pos.3 4
Total 54 74 6

Table 2.2.2c
Equipment Equivalent ISO Tube Length (ft)
1.5 in 2 in 2.5 in
A Tank outlet 3 (estimated)

A-B Tube 13
A-B Bend 90 deg. 1x3
B-C Tube 66
C-E Tube 49
C-E SRC seat valve, pos.3 33
B-E Bend 90 deg. 3x3
D LKC-2 non-return valve 39
E SRC seat valve, pos.5 46
E-F Tube 151
E-F Bend 90 deg. 4x3
F SRC seat valve, pos.3 13
Total 176 242 19
As viewed from the tables above the pressure drop through the
different equipment corresponds to the following equivalent tube
length.
38 mm (1.5 in) tube: Length = 54 m (176 ft).

51 mm (2 in) tube: Length = 74 m (242 ft).
63.5 mm (2.5 in) tube: Length = 6 m (19 ft).
The pressure drop through 100 m of tube for sizes 38 mm, 51 mm

and 63.5 mm is determined by means of the following curve, also
shown in 14.5.
~ 13.2
~ 3.0
~ 1.1
Q = 8 m3/h
Fig. 2.2.2k Pressure drop curve

The total pressure drop DH in the process is consequently calculated

as follows:
38 mm: DH = 54 x 13.2 = 7.13 m

100
51 mm: DH = 74 x 3.0 = 2.22 m

100
63.5 mm: DH = 6 x 1.1 = 0.07 m

100
DH = 7.13 + 2.22 + 0.07 = 9.42 m » 9.4 m (» 1 bar)
or
1.5 in: DH = 176 x 43 = 23.1 ft

328
2 in: DH = 242 x 10 = 7.4 ft

328
2.5 in: DH = 19 x 4 = 0.2 ft

328
DH = 23.1 + 7.4 + 0.2 = 30.7 ft » 31 ft (» 14 psi)
Example 2: Process:
Pumping glucose with a viscosity of 5000 cP from a flooded suction
through discharge pipeline as follows.
Tubes, valves and fittings:

30 m (98 ft) tube dia. 51 mm (2 in).
20 m (66 ft) tube dia. 76 mm (3 in).
2 off Non-return valves 51 mm (2 in).
6 off Bend 90 deg. dia. 51 mm (2 in).
4 off Bend 90 deg. dia. 76 mm (3 in).
3 off Tee (out through side port) 51 mm (2 in).
The pressure drop through the tubes, valves and fittings is

determined as equivalent tube length so that the total pressure drop
can be calculated.

For the pipe fittings the conversion into equivalent tube length is
carried out by reference to tables 14.7. This results in the following
equivalent tube length for the different fittings as shown below:
Table 2.2.2d
Fittings Equivalent ISO Tube Length (m)
51 mm 76 mm
Non-return valve 2 x 12
Bend 90 deg. 6x1
Bend 90 deg. 4x1
Tee 3x3
Total 39 4
Table 2.2.2e
Fittings Equivalent ISO Tube Length (ft)
2 in 3 in
Non-return valve 2 x 39
Bend 90 deg. 6x3
Bend 90 deg. 4x3
Tee 3 x 10
Total 126 12
As viewed from the tables above the pressure drop through the
different fittings corresponds to the following equivalent tube length.
Tube dia. 51 mm (2 in): Length = 39 m (126 ft).

Tube dia. 76 mm (3 in): Length = 4 m (12 ft).
Applying the viscosity correction factor for 5000 cP the equivalent

tube length is now:
Tube dia. 51 mm (2 in): Length = 39 m (126 ft) x 0.5 = 19.5 m (63 ft)
Tube dia. 76 mm (3 in): Length = 4 m (12 ft) x 0.5 = 2 m (6 ft)
These figures of 19.5 m (63 ft) and 2 m (6 ft) would be added to the
straight tube lengths given as shown below, and subsequently used in
calculating the discharge pressure at the flow rate required.
Tube dia. 51 mm (2 in): 30 m (98 ft) + 19.5 m (63 ft) = 49.5 m (161 ft)
Tube dia. 76 mm (3 in): 20 m (66 ft) + 2 m (6 ft) = 22 m (72 ft)

The friction losses in a Friction Loss Calculations

pipework system are Since laminar flow is uniform and predictable it is the only flow regime
dependent upon the type of in which the friction losses can be calculated using purely
flow characteristic that is mathematical equations. In the case of turbulent flow, mathematical
taking place. The Reynolds equations are used, but these are multiplied by a co-efficient that is
number (Re) is used to normally determined by experimental methods. This co-efficient is
determine the flow known as the Darcy friction factor (fD).
characteristic, see 2.1.7.
The Miller equation given below can be used to determine the friction
losses for both laminar and turbulent flow in a given length of pipe (L).
In dimensionally consistent SI units:

Pf = fD x L x r x V2
Dx2
Where:
Pf = pressure loss due to friction (Pa).
fD = Darcy friction factor.
L = tube length (m).
D = tube diameter (m).
V = fluid velocity (m/s).
r = density of fluid (kg/m3).

Pf = 5 x SG x fD x L x V²
D
Where:
Pf = pressure loss due to friction (bar).
D = tube diameter (mm).
SG = specific gravity.
or
Pf = 0.0823 x SG x fD x L x V²
D
Where:
Pf = pressure loss due to friction (psi).
L = tube length (ft).
D = tube diameter (in).
V = fluid velocity (ft/s).

For laminar flow, the Darcy friction factor (fD) can be calculated directly
from the equation:
fD = 64
Re
The relative roughness of For turbulent flow, the Darcy friction factor (fD) has to be determined
pipes varies with diameter, by reference to the Moody diagram (see section 14.8). It is first
type of material used and age necessary to calculate the relative roughness designated by the
of the pipe. It is usual to symbol Î.
simplify this by using an
relative roughness (k) of 0.045 Where:
mm, which is the absolute
roughness of clean Î =k
commercial steel or wrought D
iron pipes as given by Moody.
k = relative roughness which is the average heights of the pipe
internal surface peaks (mm).
D = internal pipe diameter (mm).
The term cavitation is derived 2.2.3 Cavitation

from the word cavity, meaning Cavitation is an undesirable vacuous space in the inlet port of the
a hollow space. pump normally occupied by fluid. The lowest pressure point in a
pump occurs at the pump inlet - due to local pressure reduction part
of the fluid may evaporate generating small vapour bubbles. These
bubbles are carried along by the fluid and implode instantly when they
get into areas of higher pressure.
If cavitation occurs this will result in loss of pump efficiency and noisy
operation. The life of a pump can be shortened through mechanical
damage, increased corrosion and erosion when cavitation is present.
When sizing pumps on highly viscous fluids care must be taken not to
select too higher pump speed so as to allow sufficient fluid to enter
the pump and ensure satisfactory operation.
For all pump application problems, cavitation is the most commonly

encountered. It occurs with all types of pumps, centrifugal, rotary or
reciprocating. When found, excessive pump speed and/or adverse
suction conditions will probably be the cause and reducing pump
Cavitation should be avoided speed and/or rectifying the suction condition will usually eliminate this
at all costs. problem.

2.2.4 Net Positive Suction Head (NPSH)

In addition to the total head, capacity, power and efficiency
requirements, the condition at the inlet of a pump is critical. The
system on the inlet side of the pump must allow a smooth flow of fluid
to enter the pump at a sufficiently high pressure to avoid cavitation.
This is called the Net Positive Suction Head, generally abbreviated
NPSH.
Pump manufacturers supply data about the net positive suction head
required by their pumps (NPSHr) for satisfactory operation. When
selecting a pump it is critical the net positive suction head available
(NPSHa) in the system is greater than the net positive suction head
required by the pump.
For satisfactory pump NPSHa is also referred to as N.I.P.A. (Net Inlet Pressure Available) and
operation: NPSHr is also referred to as N.I.P.R. (Net Inlet Pressure Required).
NPSHa > NPSHr
N.I.P.A. > N.I.P.R. A simplified way to look at NPSHa or N.I.P.A. is to imagine a balance
of factors working for (static pressure and positive head) and against
(friction loss and vapour pressure) the pump.
Fig. 2.2.4a NPSH balance
Against
-
For
+
Providing the factors acting for the pump outweigh those factors
acting against, there will be a positive suction pressure.

The value of NPSHa or N.I.P.A. in the system is dependent upon the

characteristic of the fluid being pumped, inlet piping, the location of
the suction vessel, and the pressure applied to the fluid in the suction
vessel. This is the actual pressure seen at the pump inlet. It is
important to note, it is the inlet system that sets the inlet condition
and not the pump. It is calculated as follows:
NPSHa = Pressure acting on + Static suction Pressure drop Vapour pressure

or surface of liquid (Pa) head (hs) (hfs) (Pvp)
N.I.P.A.
+ve -ve +ve -ve
hs
Fig. 2.2.4b NPSH calculation
NPSHa or N.I.P.A. = Pa ± hs - hfs - Pvp
Where:
Pa = Pressure absolute above fluid level (bar).
hs = Static suction head (m).
hfs = Pressure drop in suction line (m).
Pvp = Vapour pressure (bar a).
or
Where:
Pa = Pressure absolute above fluid level (psi).
hs = Static suction head (ft).
hfs = Pressure drop in suction line (ft).
Pvp = Vapour pressure (psia).
It is important the units used for calculating NPSHa or N.I.P.A. are

consistent i.e. the total figures should be in m or ft.
For low temperature applications the vapour pressure is generally not

critical and can be assumed to be negligible.

Example 1: Process:
Water at 50 °C (122o F).
3.5 m 1.5 m Pa = Pressure absolute above fluid level (1 bar = 10 m)

(14.7 psi = 33.9 ft).
hs = Static suction head (3.5 m) (11.5 ft).
hfs = Pressure drop in suction line (1.5 m) (5 ft).
Pvp = Vapour pressure (0.12 bar a = 1.2 m) (1.8 psia = 4 ft).
Fig. 2.2.4c Example NPSHr of pump selected = 3.0 m (10 ft).
NPSHa = Pa - hs - hfs - Pvp = Pa - hs - hfs - Pvp

= 10 - 3.5 - 1.5 - 1.2 (m) or = 33.9 - 11.5 - 5 - 4 (ft)
= 3.8 m = 13.4 ft
As NPSHa is greater than NPSHr, no cavitation will occur under

the conditions stated.
Example 2: Process:
0.5 bar
Water at 75 °C (167o F).
Pa = Pressure absolute above fluid level (0.5 bar = 5 m)

(7 psi = 16 ft).
1.5 m hs = Static suction head (1.5 m) (5 ft).
Pvp = Vapour pressure (0.39 bar a = 3.9 m) (5.7 psia = 13 ft).
Fig. 2.2.4d Example NPSHr of pump selected = 3.0 m (10 ft).
NPSHa = Pa + hs - hfs - Pvp = Pa + hs - hfs - Pvp

= 5 + 1.5 - 1.0 - 3.9 (m) or = 16 + 5 - 3 - 13 (ft)
= 1.6 m = 5 ft
As NPSHa is less than NPSHr, cavitation will occur under the

conditions stated.

Example 3: Process:
Glucose at 50 °C (122o F).
Pa = Pressure absolute above fluid level (1 bar = 10 m)

(14.7 psi = 33.9 ft).
hs = Static suction head (1.5 m) (5 ft).
Pvp = Vapour pressure (assumed negligible = 0 m) (0 ft).
Fig. 2.2.4e Example NPSHr of pump selected = 3.0 m (10 ft).
NPSHa = Pa + hs - hfs - Pvp = Pa + hs - hfs - Pvp

= 10 + 1.5 - 9.0 - 0 (m) or = 33.9 + 5 - 30 - 0 (ft)
= 2.5 m = 8.9 ft
As NPSHa is less than NPSHr, cavitation will occur under the

conditions stated.
From the NPSHa formula it is possible to check and optimise the

conditions which affect NPSHa.
The effects are shown as follows:
Fig. 2.2.4f Positive effect Fig. 2.2.4g Positive effect Fig. 2.2.4h Negative effect
Vapour pressure
(Temperature dependent)
Fig. 2.2.4i Negative effect Fig. 2.2.4j Negative effect Fig. 2.2.4k Negative effect

Suggestions for avoiding cavitation:

• Keep pressure drop in the inlet line to a minimum i.e. length of
line as short as possible, diameter as large as possible, and
minimal use of pipe fittings such as tees, valves etc.
• Maintain a static head as high as possible.
• Reduce fluid temperature, although caution is needed as this
may have an effect of increasing fluid viscosity, thereby
increasing pressure drop.
2.2.5 Pressure ‘Shocks’ (Water Hammer)

The term ‘shock’ is not strictly correct as shock waves only exist in
gases. The pressure shock is really a pressure wave with a velocity of
propagation much higher than the velocity of the flow, often up to
1400 m/s for steel tubes. Pressure waves are the result of rapid
changes in the velocity of the fluid in especially in long runs of piping.
The following causes changes in fluid velocity:

• Valves are closed or opened.
• Pumps are started or stopped.
• Resistance in process equipment such as valves, filters,
meters, etc.
• Changes in tube dimensions.
• Changes in flow direction.
The major pressure wave problems in process plants are usually due
to rapidly closed or opened valves. Pumps, which are rapidly/
frequently started or stopped, can also cause some problems.
When designing pipework systems it is important to keep the natural

frequency of the system as high as possible by using rigid pipework
and as many pipework supports as possible, thereby avoiding the
excitation frequency of the pump.
Effects of pressure waves:

• Noise in the tube.
• Damaged tube.
• Damaged pump, valves and other equipment.
• Cavitation.
Velocity of propagation
The velocity of propagation of the pressure wave depends on:
• Elasticity of the tubes.
• Elasticity of the fluid.
• The tubes support.

When for example, a valve is closed, the pressure wave travels from
the valve to the end of the tube. The wave is then reflected back to
the valve. These reflections are in theory continuing but in practice the
wave gradually attenuates cancelled by friction in the tube.
A pressure wave as a result of a pump stopping is more damaging

than for a pump starting due to the large change in pressure which will
continue much longer after a pump is stopped compared to a pump
starting. This is due to the low fluid velocity which results in a relatively
small damping of the pressure waves.
A pressure wave induced as a result of a pump stopping can result in

negative pressure values in long tubes, i.e. values close to the
absolute zero point which can result in cavitation if the absolute
pressure drops to the vapour pressure of the fluid.
Precautions
Pressure waves are caused by changes in the velocity of the liquid in
especially long runs of tube. Rapid changes in the operating
conditions of valves and pump are the major reasons to the pressure
waves and therefore, it is important to reduce the speed of these
changes.
There are different ways to avoid or reduce pressure waves which are
briefly described below.
Correct flow direction

Incorrect flow direction through valves can induce pressure waves
particularly as the valve functions. With air-operated seat valves
incorrect direction of flow can cause the valve plug to close rapidly
against the valve seat inducing pressure waves. Figs 2.2.5a and
2.2.5b specify the correct and incorrect flow direction for this type of
valve.
Correct flow directions in the process plant can reduce or even

prevent pressure wave problems.
Correct Incorrect
Fig. 2.2.5a Correct flow direction through Fig. 2.2.5b Incorrect flow direction
seat valve through seat valve

Damping of valves
The pressure wave induced by a seat valve can be avoided or
minimised by damping the movement of the valve plug. The damping
is carried out by means of a special damper (see fig. 2.2.5c).
Fig. 2.2.5c Oil damper for seat valve

Speed control of pumps
Speed control of a pump is a very efficient way to minimise or prevent
pressure waves. The motor is controlled by means of a soft starter or
a frequency converter so that the pump is:
• Started at a low speed which is slowly increased to duty

speed.
• Stopped by slowly decreasing from duty speed down to a
lower speed or zero.
The risk of power failure should be taken into consideration when

using speed control against pressure waves.
Equipment for industrial processes

There is various equipment available to reduce pressure waves such
as:
• Pressure storage tanks.

• Pressure towers.
• Damped or undamped non-return valves.
These however, may not be suitable for hygienic processes and

further advice may be required before they are recommended or used
in such installations.


Pump Selection
3. Pump Selection
This section gives an overview of the pump ranges currently
available from Alfa Laval and which particular pumps to apply
within various application areas.
As demands on processes increase, major factors evolve such as

the quality of products and process profitability. In view of this, the
correct selection of a pump is of great importance.
The pump must be able to carry out various duties under differing
conditions.
Some of these are as follows:

• Transfer various types of fluids/products.
• Gentle treatment of the fluids/products.
• Overcome different losses and pressure drops in the system.
• Provide hygienic, economical and long lasting operation.
• Ensure easy and safe installation, operation and maintenance.
As pumps are used in different Some pump problems can be:

locations and stages of a • The correct type of pump for the right application.
process the need for the • The correct design of pump.
correct pump in the right place • The correct selection of pump with regard to inlet and outlet
has become increasingly conditions, product data, operating conditions etc.
important. It is therefore • Correct selection of shaft seals.
necessary to be aware of the • Correct selection of drive units.
various problems that might be
encountered when selecting a
pump.

Pump Selection
3.1 General Applications Guide

The table shown below gives a general guide as to the various types
of Alfa Laval pump that may be required to suit the application.
General Requirements Centrifugal Liquid Ring Rotary Lobe
Product/Fluid Requirements
Max. Viscosity 1000 cP 200 cP 1000000 cP
o o
Max. Pumping Temperature 140°C (284 F) 140°C (284 F) 200°C (392oF)
Min. Pumping Temperature - 10°C (14oF) - 10°C (14oF) - 20°C (-4oF)
Ability to pump abrasive products Not recommended Not recommended Fair
Ability to pump fluids containing air or gases Not recommended Recommended Fair
Ability to pump shear sensitive media Fair Not recommended Recommended
Ability to pump solids in suspension Fair Not recommended Recommended
CIP capability (sanitary) Recommended Recommended Recommended
Dry running capability (when fitted with
flushed/quench mechanical seals) Recommended Recommended Recommended
Self Draining capability Recommended Recommended Recommended
Performance Requirements
Max. Capacity - m³/hr 440 80 115
Max. Capacity - US gall/min 1936 352 506
Max. Discharge Pressure - bar 20 5.5 20
Max. Discharge Pressure - psig 290 80 290
Ability to vary flow rate Fair Not recommended Recommended
Suction Lift capability (primed wet) Recommended Recommended Recommended
Suction Lift capability (unprimed - dry) Not recommended Recommended Fair
Drive Availability
Air motor No No Yes
Diesel engine No No Yes
Electric motor Yes Yes Yes
Hydraulic motor Yes Yes Yes
Petrol engine No No Yes
Compliance with International
3-A Yes Yes Yes
FDA Yes Yes Yes
EHEDG Yes No Yes
Table 3.1a

Pump Selection
3.2 Pumps for Sanitary Applications

Alfa Laval Pump Ranges
Pump Ranges from Alfa Laval
Centrifugal Liquid Ring Rotary Lobe
LKH LKH Multistage MR SRU SX
LKHP High Pressure LKHSP
LKHI LKH Ultra Pure
Fig. 3.2a Pump ranges

The following table illustrates which Alfa Laval pump ranges can be
used in various sanitary application areas. A detailed description of
these pump ranges is given in section 4.
Pump Type Pump Range Application Area
Soap and Detergent

Pharmaceutical
Confectionery
Other Food
Soft Drink
Brewery
Sugar
Water
Dairy
Centrifugal LKH ü ü ü ü ü ü ü ü
LKH-Multistage ü ü ü ü ü ü ü ü
LKHP-High Pressure ü ü ü ü
LKHSP ü ü ü ü
LKHI ü ü ü ü ü ü ü ü
LKH-Ultra Pure ü ü ü ü ü ü
Rotary Lobe SRU ü ü ü ü ü ü ü ü

SX ü ü ü ü ü ü ü
Table 3.2a
The Liquid Ring pump is used in most of these sanitary application

areas dedicated for CIP and tank emptying duties.
Brewery
Alfa Laval Centrifugal and Rotary Lobe pumps are used in most
process stages of brewing from wort handling to beer pasteurisation
and filling. Generally, rotary lobe pumps best perform high fluid
viscosity applications, such as liquid sugar tanker offloading and malt
syrups, whereas low fluid viscosity applications, such as beer and
water chilling, are mostly carried out using centrifugal pumps. During
the fermentation process, rotary lobe pumps with their gentle
pumping action are ideally used handling yeast containing delicate
cells.

Pump Selection
Confectionery
Alfa Laval is a major supplier of pumping equipment to this industry,
providing pumps to all the major confectionery companies. Rotary
lobe pumps being used on high viscosity products such as
chocolate, glucose, biscuit cream and fondant. Confectionery
products that contain particulate matter, such as fruit pie fillings, can
be handled with the rotary lobe pump. Centrifugal pumps can be
commonly found on fat and vegetable oil applications.
Dairy
Alfa Laval Centrifugal and Rotary Lobe pumps, with their hygienic
construction and conforming to 3-A standards (see section 11), are
used extensively throughout the dairy industry on milk processing,
cream and cultured products such as yoghurt.
Other Food
‘Other Food’ means other than Confectionery, Dairy and Sugar -
generally Alfa Laval Centrifugal and Rotary Lobe pumps can be found
on general transfer duties handling products such as petfood, sauces
and flavourings.
Pharmaceutical
Alfa Laval Centrifugal and Rotary Lobe pumps can be found on many
applications within this industry where hygiene and corrosion
resistance is paramount, such as cosmetic creams, protein solutions,
toothpaste, perfume, shampoo and blood products.
Soap and Detergent

Alfa Laval Centrifugal and Rotary Lobe pumps can be found on many
applications within this industry, handling products such as neat soap,
sulphonic acid, fabric conditioner, dishwash liquid, fatty acid, lauryl
ether sulphate, liquid detergent and surfactants.
Soft Drink
Alfa Laval Centrifugal pumps are mainly used on applications handling
thin liquid sugar solutions, water and flavourings. Alfa Laval Rotary
Lobe pumps are mainly used on applications handling high viscosity
fruit juice concentrates.
Sugar
Alfa Laval Rotary Lobe pumps, with their ability to handle highly
viscosity abrasive products, can be found within many areas of sugar
refined products requiring hygienic handling, such as high boiled
sugars, glucose solutions and sugar syrups used in confectionery,
bakery, brewing and carbonated soft drinks.

Pump Selection
Water
Alfa Laval Centrifugal pumps provide a low cost effective solution for
high purity water and water like applications.
3.3 PumpCAS Selection and Configuration

Tool
Pump selection for both Centrifugal and Rotary Lobe Pumps can be
made by the use of Alfa Laval’s PumpCAS selection program. This
program prompts the user to enter pump duty information and
selects the pump from the product range most suited to their specific
application. The program selects both centrifugal and rotary lobe
pumps and provides the user with a comparison of features enabling
the most appropriate technology to be chosen. If one or other
technology is not suited to a specific application (this could be due to
physical limitations and or fluid characteristics) the program will advise
the user, and recommend an alternative solution.
As well as performing the pump selection, PumpCAS also extracts

data from a comprehensive liquids database enabling it to suggest
viscosity, SG, maximum speed, elastomer compatibility and primary
seal configuration. After the pump has been selected, the user will be
assisted to complete a detailed pump unit specification. This will
include additional options such as pressure relief valves, heating or
cooling devices, connection specifications etc. for which the price of
the pump and its configuration code (item number) will be
automatically generated aiding the quotation and/or ordering
process.
If you would like a copy of the In addition, PumpCAS will also provide detailed parts list for the
Alfa Laval PumpCAS pump with item numbers with all recommended spare parts identified
Selection and Configuration and priced. Dimensional details in the form of general arrangement
Tool please contact your local drawings can also be generated.
Alfa Laval sales company.
A link to all technical information that may be required to accompany
the quotation such as Operation manuals, generic or specific
performance curves, and technical data sheets will also be provided,
along with direct access to this Alfa Laval Pump Handbook for any
additional supporting information that may be required.

Pump Selection
Flexibility has been built in to the software to enable specific enquiries

to be answered without the need to complete a full pump selection.
For example, recommended spares lists can be extracted based on
an existing configuration code or direct access to technical
information relating to a specific pump technology is possible.
The liquids database contained within PumpCAS is based on

rheological tests performed over many years on end users liquids at
Alfa Laval’s chemical laboratory, and will be continually added to as
additional products are tested. All information is offered for guidance
purposes only.

Pump Description
4. Pump Description
This section gives a description of Alfa Laval pump ranges
including design, principle of operation and pump model types.
4.1 Centrifugal Pumps

4.1.1 General
The Alfa Laval range of Centrifugal Pumps has been designed
specially for use in the food, dairy, beverage, pharmaceutical and light
chemical industries. Centrifugal pumps including multi-stage designs
and those for high inlet pressure, can handle most low viscosity
applications. Centrifugal pumps can provide the most cost effective
solution.
Attributes include:
• High efficiency.
• Low power consumption.
• Low noise level.
• Low NPSH requirement.
• Easy maintenance.

Pump Description
4.1.2 Principle of Operation

Fluid is directed to the impeller eye and is forced into a circular
movement by the rotation of the impeller vanes. As a result of this
rotation, the impeller vanes transfer mechanical work to the fluid in the
impeller channel, which is formed by the impeller vanes. The fluid is
then pressed out of the impeller by means of centrifugal force and
finally leaves the impeller channel with increased pressure and velocity.
The velocity of the fluid is also partly converted into pressure by the
Fig. 4.1.2a Principle of operation pump casing before it leaves the pump through the outlet.
The principle of the multi-stage centrifugal pump is the same as the

conventional centrifugal pump. The pump consists, however, of
several impellers (several stages) which increase the pressure from
one stage to another but flow rate is unchanged. The multi-stage
centrifugal pump operates as if several conventional centrifugal
pumps are connected in series.
Fig. 4.1.2b Multistage centrifugal pump
4.1.3 Design
In general the Alfa Laval centrifugal pump does not contain many
parts, with the pumphead being connected to a standard electric
motor. The impeller is fixed onto the pump shaft which is housed in a
pump casing and back plate – these components are described
below:
Impeller
The impeller is of cast manufacture and open type; i.e. the impeller
vanes are open in front. This type allows visual inspection of the vanes
and the area between them.
A semi-open impeller is also available which is easy to clean and

suitable for polishing.
Fig. 4.1.3a Semi-open impeller
The impeller has two or

multiple vanes depending on
the type of centrifugal pump.
The impeller diameter and
width will vary dependent
upon the duty requirements.

Pump Description
Pump Casing
The pump casing is of pressed steel manufacture, complete with male
screwed connections and can be supplied with fittings or clamp liners.
The pump casing is designed for

multi position outlet, with 360°
flexibility.
Fig. 4.1.3b Pump casing
Fig. 4.1.3c 360o flexibility
Back Plate
The back plate is of pressed steel manufacture, which together with
the pump casing form the actual fluid chamber in which the fluid is
transferred by means of the impeller.
Fig. 4.1.3d Back plate

Mechanical Seal
The connection between the motor shaft/pump shaft and the pump
casing is sealed by means of a mechanical seal, which is described in
section 6.
Shroud and Legs

Most pump types are fitted with shrouds and adjustable legs. The
shroud is insulated to keep noise to a minimum and protect the
motor against damage.
Please note Alfa Laval Centrifugal pumps for the USA market
are supplied without shrouds.
Fig. 4.1.3e Pump with shroud and legs

Pump Description
Pump Shaft/Connections
Most pumps have stub shafts that are fixed to the motor shafts by
means of compression couplings, eliminating the use of keyways. The
stub shaft assembly design provides a simple, yet secure method of
drive that reduces vibration and noise. On the multistage centrifugal
pump the length of the pump shaft will differ depending upon the
number of impellers fitted.
Fig. 4.1.3f Compression coupling
Adaptor
Most pumps are fitted with a standard IEC electric motor. The
connection between the motor and back plate is made by means of
an adaptor, which can be attached to any standard IEC or C-frame
electric motor.
Pumps supplied with direct coupled motors have no adaptors.
Fig. 4.1.3g Adapter
4.1.4 Pump Range

The Alfa Laval Centrifugal Pump portfolio comprises of different
ranges as follows:
LKH Range
The LKH pump is a highly efficient and economical centrifugal pump,
meeting sanitary requirements with gentle product treatment and
chemical resistance.
Fig. 4.1.4a LKH Fig. 4.1.4b LKH (USA version)
The LKH range is available in twelve sizes: LKH-5, -10, -15, -20, -25,
-35, -40, -45, -50, -60, -70 and -80.
Flow rates for 50 Hz up to 440 m³/h (1936 US gall/min) and

differential pressures up to 11.5 bar (165 psig) and for 60 Hz up to
440 m3/h (1936 US gall/min) and differential pressure up to 16 bar
(230 psig).

Pump Description
LKH-Multistage Range
These pumps are primarily used in applications with high outlet
pressure and low capacity requirements such as breweries, reverse
osmosis and ultra-filtration. The pumps are available as two, three or
four stage models (i.e. pumps fitted with two, three or four impellers
respectively).
Fig. 4.1.4c LKH-Multistage Fig. 4.1.4d LKH-Multistage (USA version)
The LKH-Multistage range is Pump Size Number of Stages

available in six sizes.
LKH-112 2
LKH-113 3
LKH-114 4
LKH-122 2
LKH-123 3
LKH-124 4
Flow rates for 50 Hz up to 75 m³/h (330 US gall/min) and discharge

pressures up to 40 bar (580 psig) with boost pressures up to 19 bar
(275 psig) and for 60 Hz up to 80 m3/h (352 US gall/min) and boost
pressures up to 26 bar (375 psig).
For inlet pressures greater than 10 bar (145 psig) a ‘special’ motor is
used incorporating fixed angular contact bearings due to axial thrust.
LKHP-High Pressure Range

These pumps are designed to handle high inlet pressures built with
reinforced pump casing and back plate. Application areas include
reverse osmosis mono-filtration and ultra-filtration.
Fig. 4.1.4e LKHP-High Pressure Fig. 4.1.4f LKHP-High Pressure (USA

version)

Pump Description
The LKHP-High Pressure range is available in nine sizes, LKHP-10,

-15, -20, -25, -35, -40, -45, -50 and -60.
The pump range is designed for inlet pressures up to 40 bar

(580 psig). Flow rates for 50 Hz up to 240 m³/h (1056 US gall/min)
with differential pressures up to 8 bar (115 psig). For 60 Hz, flow
rates up to 275 m3/h (1210 US gall/min) with differential pressures up
to 11 bar (160 psig).
For these high inlet pressures a ‘special’ motor with fixed angular
contact bearings is used due to axial thrust.
LKHSP Range
The LKHSP self-priming pump is specially designed for pumping
fluids containing air or gas without loosing its pumping ability. The
pump is for use in food, chemical, pharmaceutical and other similar
industries.
These pumps can be used for tank emptying or as a CIP return pump
where there is a risk of air or gas mixing with the fluid in the suction
Fig. 4.1.4g LKHSP line. The pump is capable of creating a vacuum of 0.6 bar, depending
upon pump size.
The pump is supplied complete with a tank, a non-return valve

(normally closed) on the inlet side, a tee and a non-return valve
(normally open) on the bypass line.
The LKHSP range is available in five sizes, LKHSP-10, -20, -25, -35
and -40.
Flow rates up to 90 m³/h (396 US gall/min) and differential pressures

for 50 Hz up to 8 bar (115 psig) and for 60 Hz, 11 bar (160 psig).
LKHI Range
This pump range is similar to the LKH range but is suitable for inlet
pressures up to 16 bar (230 psig). The pump can withstand this high
inlet pressure due to being fitted with an internal shaft seal.
The LKHI range is available in nine sizes, LKHI-10, -15, -20 ,-25, -35,
-40, -50 and -60.
Flow rates for 50 Hz up to 240 m³/h (1056 US gall/min) with

differential pressures up to 8 bar (115 psig). For 60 Hz, flow rates up
to 275 m3/h (1210 US gall/min) with differential pressures up to 11
bar (160 psig).

Pump Description
For inlet pressures greater than 10 bar (145 psig) a ‘special’ motor is
used incorporating fixed angular contact bearings due to axial thrust.
LKH-UltraPure Range
These pumps are designed for high purity applications such as
water-for-injection (WFI). The pump is fully drainable supplied with
associated pipework, fittings and valves. Another feature of this
pump is self-venting, due to the pump casing outlet being turned 45°.
Fig. 4.1.4h LKH-UltraPure Fig. 4.1.4i LKH-UltraPure (USA version)
The LKH-UltraPure range is available in five sizes, LKH-UltraPure-10,

-20, -25, -35 and -40.

for 50 Hz up to 8 bar (115 psig) and for 60 Hz, 11 bar (160 psig).
C – Series range
The C-Series is the original, all-purpose Alfa Laval centrifugal pump for
less demanding applications.
The range is designed for meeting sanitary requirements and can be

Cleaned-In-Place.
The C-series is produced mainly for the USA and is available in five
Fig. 4.1.4j C-Series sizes, C114, C216, C218, C328 and C4410.
Flow rates for 60 Hz up to 227 m3/h (1000 US gall/min) and

differential pressures up to 10 bar (145 psig).

Pump Description
4.2 Liquid Ring Pumps

4.2.1 General
The Alfa Laval range of Liquid Ring Pumps are specially designed for
use in food, chemical and pharmaceutical industries where pumping
liquids containing air or gases. As the liquid ring pump is self-priming
when half filled with fluid, it is capable of pumping from a suction line
partly filled with air or gases. As these pumps are self-priming, they
are ideally used as return pumps in CIP systems.
Attributes include:
• Self-priming (when pump casing is half filled with fluid).
• Suitable for aerated fluids.
• High efficiency.
• Minimal maintenance.

The liquid-ring pump is in principle a centrifugal pump. The pump is,
however, self-priming when half filled with fluid. The self-priming
capability is a result of the impeller design, small tolerances between
the impeller and the pump casing, and due to a side channel made in
the pump casing and/or the front cover. The discharge line should be
routed 1 to 2 metres vertically upwards from the pump outlet
connections to maintain the liquid ring in the side channels (see 12.5.1).
Fig. 4.2.2a Principle of operation
The sequence of a section between two impeller vanes during one

revolution is described in the following:
a) There is a certain fluid volume in the gap between the vanes

which is not in contact with the channel.
a) to b) The gap is in contact with the channel, which gradually

becomes deeper. Part of the fluid between the vanes fills the
channel. The centrifugal force pushes the fluid outwards and
consequently forms a vacuum at the centre of the impeller.

Pump Description
b) to c) The depth of the channel is still increased. The fluid volume is

still forced outwards and consequently the fluid-free volume
between the vanes is increased until it reaches a maximum
where the channel has maximum depth.
d) The vacuum created induces air from the suction line through
the inlet at “d”.
d) to e) Air and fluid are circulated with the impeller until the depth of
the channel begins to decrease. The volume between the
vanes is gradually reduced as the depth of the channel is
reduced and consequently pressure is build up at the centre of
the impeller.
e) The fluid is still forced outwards and the air remains at the
centre of the impeller. The same volume of air that was
induced through the inlet is now expelled through the outlet at
“e” due to the pressure increase at the centre of the impeller.
e) to a) The section between the vanes will be refilled with fluid when it
has passed the channel as only air and no fluid has yet been
pumped. The cycle described above is continuously repeated
as the impeller has several sections and rotates at approx.
1500 rev/min. (50 Hz) or 1800 rev/min. (60Hz).
When all the air is removed from the suction line the described cycle is
repeated for the fluid. The pump now operates as a fluid pump.
4.2.3 Design
As for centrifugal pumps, the liquid ring pump does not contain many
parts – the pumphead being connected to a standard electric motor.
The impeller is fixed onto the pump shaft housed in a pump casing
and casing cover.
Impeller
The impeller is of cast manufacture with straight radial impeller vanes.
There is only one impeller size for each type of liquid ring pump.
Fig. 4.2.3a Impeller

Pump Description
Pump Casing and Casing Cover

The pump casing is of cast manufacture complete with male screwed
connections and fittings or clamp liners. The pump casing cover is
also of cast manufacture, with or without a channel depending upon
pump type/size. The pump casing and casing cover form the actual
fluid chamber in which the fluid is transferred by means of the impeller.
Fig. 4.2.3b Pump with one channel Fig. 4.2.3c Pump with two channels
Mechanical Seal
The connection between the motor shaft/pump shaft and the pump
casing is sealed by means of a mechanical seal, which is described in
section 6.
Shroud and Legs

Pumps fitted with standard IEC motors utilise the shrouds and legs
used on the LKH centrifugal pump range.
Please note Alfa Laval Liquid Ring pumps for the USA market
are supplied without shrouds.
Fig. 4.2.3d Pump with IEC standard

motor
Pump Shaft/Connections
Most pumps have stub shafts that are fixed to the motor shafts by
means of compression couplings, as used on Centrifugal pumps.
Adaptor
For pumps fitted with a standard IEC electric motor (not MR-300
model), the connection between the motor and pump casing is made
by means of an adaptor, similar to that used on Centrifugal pumps.

Pump Description
4.2.4 Pump Range

The Alfa Laval Liquid Ring Pump range is designated the MR range.
MR Range
The MR range is available in four sizes, MR-166S, MR-185S,
MR-200S and MR-300.
Fig. 4.2.4a MR-166S, MR-185S and Fig. 4.2.4b MR-300 Fig. 4.2.4c MR pump (USA version)
MR-200S
The pump range is designed for inlet pressures up to 4 bar (60 psig).
of 5 bar (73 psig) for 50 Hz and 6 bar (87 psig) for 60 Hz.

Pump Description
4.3 Rotary Lobe Pumps

4.3.1 General
The Alfa Laval range of Rotary Lobe Pumps with its non-contact
pump element design has the ability to cover a wide range of
applications in industry. The hygienic design, anti-corrosive stainless
steel construction and smooth pumping action have long established
these pumps in the food, beverage, dairy and pharmaceutical
industries.
Attributes include:
• Gentle transfer of delicate suspended solids.
• Bi-directional operation.
• Compact size with high performance and low energy input.
• Ability to pump shear sensitive media.
• Easy maintenance.

Alfa Laval ranges of Rotary Lobe pumps are of conventional design
operating with no internal contacting parts in the pump head. The
pumping principle is explained with reference to the following diagram,
which shows the displacement of fluid from pump inlet to outlet. The
rotors are driven by a gear train in the pump gear gearbox providing
accurate synchronisation or timing of the rotors. The rotors
contra-rotate within the pump head carrying fluid through the pump,
in the cavities formed between the dwell of the rotor and the interior
of the rotorcase.
In hydraulic terms, the motion of the counter rotating rotors creates a

partial vacuum that allows atmospheric pressure or other external
pressures to force fluid into the pump chamber. As the rotors rotate
an expanding cavity is formed which is filled with fluid. As the rotors
separate, each dwell forms a cavity. The meshing of the rotor causes
a diminishing cavity with the fluid being displaced into the outlet port.

Pump Description
Horizontally ported pump (top shaft drive)
1 2 3 4
Vertically ported pump (left hand shaft drive)
1 2 3 4
Fig. 4.3.2a Principle of operation
4.3.3 Pump Range

Alfa Laval Rotary Lobe Pumps can be supplied bare shaft (without
drive) or complete with drive such as electric motor, air motor, and
diesel or petrol engine (see 8.2.7). Ranges primarily as follows:
SRU Range
The SRU pump range has been designed for use on general transfer
duties throughout the brewing, dairy, food and chemical
manufacturing processes.
The SRU range is available in six series each having two pumphead
displacements and two different shaft materials.
Fig. 4.3.3a SRU • Displacement is the theoretical amount of fluid the pump will
transfer per revolution.
• Duplex stainless steel material used for higher pressures.

Pump Description
The SRU pump range incorporates a universally mounted gearbox on

series 1 - 4. This gives the flexibility of mounting pumps with the inlet
and outlet ports in either a vertical or horizontal plane by changing the
foot and foot position. For the larger series 5 and 6, either horizontal
or vertical plane inlet and outlet porting is achieved by using
dedicated gearbox castings. This pump range also incorporates full
bore through porting complying with international standards
BS4825/ISO2037, maximising inlet and outlet port efficiency and
NPSH characteristics.
Flow rates up to 106 m³/h (466 US gall/min) and pressures up to 20

bar (290 psig).
The SRU range conforms to USA 3A requirements.
Pump Nomenclature
SRU Build Selection SRU Model Displacement Differential Max.
Series Pressure Speed
Pump head
Gearbox
Shaft
UK gall/ US gall/
code
Litres/
rev 100 rev 100 rev bar psig rev/min
1 005
008
L or H
L or H
D
D
SRU1/005/LD or HD
SRU1/008/LD or HD
0.053
0.085
1.17
1.87
1.4
2.25
8
5
115
75
1000
1000
013 L or H S SRU2/013/LS or HS 0.128 2.82 3.38 10 145 1000
2 013
018
L
L
or
or
H
H
D
S
SRU2/013/LD
SRU2/018/LS
or
or
HD
HS
0.128
0.181
2.82
3.98
3.38
4.78
15
7
215
100
1000
1000
018 L or H D SRU2/018/LD or HD 0.181 3.98 4.78 10 145 1000
027 L or H S SRU3/027/LS or HS 0.266 5.85 7.03 10 145 1000
3 027
038
L
L
or
or
H
H
D
S
SRU3/027/LD
SRU3/038/LS
or
or
HD
HS
0.266
0.384
5.85
8.45
7.03
10.15
15
7
215
100
1000
1000
038 L or H D SRU3/038/LD or HD 0.384 8.45 10.15 10 145 1000
055 L or H S SRU4/055/LS or HS 0.554 12.19 14.64 10 145 1000
4 12.19 14.64 290

055 L or H D SRU4/055/LD or HD 0.554 20 1000
079 L or H S SRU4/079/LS or HS 0.79 17.38 20.87 7 100 1000
079 L or H D SRU4/079/LD or HD 0.79 17.38 20.87 15 215 1000
116 L or H S SRU5/116/LS or HS 1.16 25.52 30.65 10 145 600
5 116 L or H D SRU5/116/LD or HD 1.16 25.52 30.65 20 290 600

168 L or H S SRU5/168/LS or HS 1.68 36.95 44.39 7 100 600
168 L or H D SRU5/168/LD or HD 1.68 36.95 44.39 15 215 600
260 L or H S SRU6/260/LS or HS 2.60 57.20 68.70 10 145 500
6 260 L or H D SRU6/260/LD or HD 2.60 57.20 68.70 20 290 500

353 L or H S SRU6/353/LS or HS 3.53 77.65 93.26 7 100 500
353 L or H D SRU6/353/LD or HD 3.53 77.65 93.26 15 215 500
L - Horizontal Porting
H - Vertical Porting
S - Stainless Steel
D - Duplex Stainless Steel
Table 4.3.3a

Pump Description
SX Range
The SX pump range is designed to be used where ultra-clean
operation is critical, suited to applications in the pharmaceutical,
biotechnology, fine chemical and speciality food industries. This pump
range like the SRU range incorporates a universally mounted gearbox
on series 1 - 4. This gives the flexibility of mounting pumps with the
inlet and outlet ports in either a vertical or horizontal plane by
changing the foot and foot position. For the larger series 5, 6 and 7,
Fig. 4.3.3b SX only vertical plane inlet and outlet porting is available by using a
dedicated gearbox casting. This pump range also incorporates full
bore through porting complying with international standards
BS4825/ISO2037, maximising the inlet and outlet efficiency of the
pump and the NPSH characteristics.
The SX range has been certified by EHEDG (European Hygienic

Equipment Design Group) as fully CIP cleanable to their protocol. In
addition to being EHEDG compliant, the SX pump also conforms to
the USA 3A standard and all media contacting components are FDA
compliant. All media contacting elastomers are controlled
compression joints to prevent pumped media leaking to atmosphere
(see section 6.2).
The SX range is available in seven series each having two pumphead

displacements. Flow rates up to 115 m³/h (506 US gall/min) and
pressures up to 15 bar (215 psig).
Pump Nomenclature
SX Build Selection SX Model Displacement Differential Max.
Series Pressure Speed
Gearbox
Pump
Litres/ UK gall/ US gall/

head
code
rev 100 rev 100 rev bar psig rev/min
1 005
007
H or U
H or U
SX1/005/H or U
SX1/007/H or U
0.05
0.07
1.11
1.54
1.32
1.85
12
7
175
100
1400
1400
2 013
018
H or U
H or U
SX2/013/H or U
SX2/018/H or U
0.128
0.181
2.82
3.98
3.38
4.78
15
7
215
100
1000
1000
3 027
035
H or U
H or U
SX3/027/H or U
SX3/035/H or U
0.266
0.35
5.85
7.70
7.03
9.25
15
7
215
100
1000
1000
4 046
063
H or U
H or U
SX4/046/H or U
SX4/063/H or U
0.46
0.63
10.12
13.86
12.15
16.65
15
10
215
145
1000
1000
5 082
115
H
H
SX5/082/H
SX5/115/H
0.82
1.15
18.04
25.30
21.67
30.38
15
10
215
145
600
600
6 140
190
H
H
SX6/140/H
SX6/190/H
1.40
1.90
30.80
41.80
36.99
50.20
15
10
215
145
500
500
7 250
380
H
H
SX7/250/H
SX7/380/H
2.50
3.80
55.00
83.60
66.05
100.40
15
10
215
145
500
500
H - Vertical Port (EHEDG approved)
U - Universal mounting (not EHEDG approved) Table 4.3.3b

Pump Description

Pump Materials of Construction
5. Pump Materials of Construction

This section describes the materials, both metallic and
elastomeric, that are used in the construction of Alfa Laval
pump ranges.
5.1 Main Components

Pumps today can be manufactured from a number of different
materials dependent upon the product being pumped and its
environment.
For Alfa Laval pump ranges this is generally stainless steel and can be
split into two main categories:
• Product Wetted Parts
(i.e. Metallic and elastomeric parts in contact with the fluid
being pumped).
• Non-product Wetted Parts
(i.e. Metallic and elastomeric parts not in contact with the fluid
being pumped).
Centrifugal and Liquid Ring Pumps
Main Pump Component Product Wetted Parts Non-product Wetted Parts
Adaptor AISI 304 or Werkstoff 1.4301

Backplate AISI 316L or Werkstoff 1.4404
Impeller AISI 316L or Werkstoff 1.4404
Pump Casing AISI 316L or Werkstoff 1.4404
Pump Shaft AISI 316L or Werkstoff 1.4404
Shroud and Legs AISI 304 or Werkstoff 1.4301
Table 5.1a
Casing
Shroud
Adaptor
Fig. 5.1a Centrifugal pump

Rotary lobe pumps

Main Pump SRU Models SX Models
Component Metallic Product Metallic Non-product Metallic Product Metallic Non-product
Wetted Parts Wetted Parts Wetted Parts Wetted Parts
Gearcase BS EN 1561:1977 BS EN 1561:1977

grade 250 cast iron grade 250 cast iron
Rotor Werkstoff 1.4404 or BS EN 10088-3:1995
316L, Non-galling grade 1.4404 or 316L
alloy or rubber covered
Rotorcase BS 3100:1991 316 C12 BS3100:1991 316 C12
or 316L or 316L
or BS EN10088-3:1995
grade 1.4404
Rotorcase Cover BS3100:1991 316 C12 BS3100:1991 316 C12
or 316L or 316L
or BS EN10088-3:1995 or BS EN10088-3:1995
grade 1.4404 grade 1.4404
Shaft BS EN10088-3:1995 Duplex stainless steel
grade 1.4404 or 316L (AISI 329 or
or duplex stainless steel BS EN10088-3:1995
(AISI 329 or grade 1.4462)
BS EN10088-3:1995
grade 1.4462)
Table 5.1b
Product seal area Drive shaft

Rotorcase
Gearbox
Ports
Rotorcase cover
Fig. 5.1b Rotary lobe pump
For description of elastomers used see 5.3.
For mechanical seal components see 6.1.

Surface finish of product 5.2 Steel Surfaces

wetted steel components has
become a major factor in the
The ‘standard’ machined surface finish on pumps can be enhanced by
food, pharmaceutical and
the following methods:
biotechnology industries
where hygiene and
• Rumbling.
cleanability are of paramount
importance.
• Shot blasting.
• Electropolishing.
• Mechanical (Hand) polishing.
Rumbling
This is achieved by vibrating the pump components with abrasive
particulate such as stones and steel balls.
Shotblasting
This method involves blasting finished components with small metallic
particles at great force to achieve the surface finish required. For
Alfa Laval centrifugal stainless steel pump components, fine particles
of stainless steel are used in this process to avoid contamination.
Electropolishing
This is an electro-chemical process in which the stainless steel
component is immersed into a chemical bath and subjected to an
electrical current. A controlled amount of metal is removed from all
surfaces evenly. The appearance is ‘Semi bright’.
Mechanical (Hand)
This is required when it is necessary to improve the surface finish
beyond that achieved by electropolishing only i.e. a ‘Mirror finish’.
It typically involves:
• Fine grinding using felt and compound.
• Brushing using bristle brushes and compound to remove any

cutting marks left from fine grinding, and to reach any
awkward areas.
• Polishing using mops and compound to obtain a mirror

polished effect.

Surface Roughness
The most commonly used surface roughness measurement is Ra and
is defined as ‘the arithmetic mean of the absolute value of the
departure of the profile from the mean line’. Ra is measured in micron
(µm). The surface roughness can alternatively be specified by a Grit
value. The Grit value specifies the grain size of the coating of the
grinding tool used.
The approximate connection between the Ra value and the Grit value
is as follows:
Ra = 0.8 µm (32 Ra) » 150 Grit (3A standard).
Ra = 1.6 µm (64 Ra) » 100 Grit.
Fig. 5.2a Surface roughness
For Alfa Laval Centrifugal and Liquid Ring Pumps see table below:
Pump surfaces Standard surface Optional surface Optional surface

roughness Ra (mm) roughness (3A finish) roughness (3A finish)
by Rumbling method Ra (mm) by Mechanical Ra (mm) by shot
(Hand) method blasting (Hand or
Electropolished)
Product wetted surfaces < 1.6 (64 Ra) < 0.8 (32 Ra) < 0.5 (20 Ra)
External exposed surfaces < 1.6 (64 Ra) < 1.6 (64 Ra) < 1.6 (64 Ra)
Cast surfaces < 3.2 (125 Ra) £ 3.2 (125 Ra) £ 3.2 (125 Ra)
Other surfaces £ 6.3 (250 Ra) £ 6.3 (250 Ra) £ 6.3 (250 Ra)
Table 5.2a
Alfa Laval Centrifugal and Liquid Ring pumps supplied in the USA have
all product wetted surfaces and external exposed surfaces to 0.8 Ra.
For Alfa Laval Stainless Steel Rotary Lobe Pumps the surface
roughness on product wetted parts such as rotors, rotorcase, rotor
nuts and rotorcase covers is as follows:
‘Standard’ - 0.8 Ra
Electropolishing - 0.8 Ra
Mechanical (Hand) - 0.5 Ra

5.3 Elastomers
Alfa Laval pump ranges incorporate elastomers of different material
and characteristics dependent upon application within the pump and
the fluid being pumped.
Various elastomer types are specified below. It is difficult to predict

the lifetime of elastomers as they will be affected by many factors,
e.g. chemical attack, temperature, mechanical wear etc.
A selection guide is shown in NBR (Nitrile)

section 14.10. • Available as O-rings or Quad-rings (depending on pump type).
• Used as static or dynamic seals.
• Resistant to most hydrocarbons, e.g. oil and grease.
• Sufficiently resistant to diluted lye and diluted nitric acid.
• Temperature range - minus 40°C min to 100°C max.
(minus 40oF to 212oF max.).
• Is attacked by ozone.
EPDM (Ethylene Propylene)

• Available as O-rings or Quad-rings (depending on pump type).
• Resistant to most products used within the food industry.
• Resistant to ozone and radiation.
• Not resistant to organic and non-organic oils and fats.
FPM (Fluorinated rubber)

- alternatively known as Vitonâ
• Available as O-rings or Quad-rings (depending on pump type).
• Often used when other rubber qualities are unsuitable.
• Resistant to most chemicals and ozone.
• Not suitable for fluids such as water, steam, lye, acid and
alcohol’s being pumped hot.

PTFE (Polytetrafluoro Ethylene)

• Can be used as “cover” for O-ring seals of EPDM
(i.e. encapsulated).
• Resistant to ozone.
• Resistant to almost all products.
• Not elastic, tendency to compression set.
MVQ (Silicone)
• Resistant to ozone, alcohol’s, glycol’s and most products
used within food industry.
• Not resistant to steam, inorganic acids, mineral oils, or most
organic solvents.
FEP (Fluorinated Ethylene Propylene)

• FEP covered (vulcanised) FPM or MVQ O-rings.
• Suitable for temperatures up to approx. 200°C (392oF).
• More elastic than PTFE covered EPDM.
Kalrez® (Perfluoroelastomer)
• Temperature range – minus 20°C min to 250°C max.
(minus 4°F to 482°F max.).
• Elastic.
Chemraz® (Perfluroelastomer)
• Temperature range – minus 30°C min to 250°C max.
(minus 22°F to 482°F max.).
• Elastic.

Pump sealing
6. Pump Sealing
This section describes the principle of pump sealing and illustrates the different
sealing arrangements used on Alfa Laval pump ranges. A general seal selection
guide is included, together with various operating parameters.
This section covers the shaft sealing devices used on Alfa Laval
Centrifugal, Liquid Ring and Rotary Lobe Pumps. In addition to shaft
seals, other proprietary seals not detailed in this section, such as ‘o’
rings and lip seals can be found on the pumphead and gearcase.
“A Pump is only as good as it’s shaft seal”
A successful pump application largely depends upon the selection

and application of suitable fluid sealing devices. Just as we know that
there is no single pump that can embrace the diverse range of fluids
and applications whilst meeting individual market requirements and
legislations, the same can be said of fluid sealing devices. This is
clearly illustrated by the large range of shaft seal arrangements, both
mechanical and packed gland, that are available to the pump
manufacturer.
Shaft sealing devices used in Alfa Laval Centrifugal, Liquid Ring and
Rotary Lobe pumps include:
• Mechanical Seals (see 6.2).

- Single externally mounted.
- Single internally mounted.
- Single externally mounted for external flush.
- Single internally mounted for product recirculation or
external flush.
- Double ‘back to back’ with the inboard seal externally
mounted for flush.
• Packed Glands (see 6.3).

- Both with and without lantern rings for flush.

Pump sealing
Centrifugal and Liquid Ring pumps only have one shaft seal whereas
Rotary Lobe pumps employ a minimum of two shaft seals (one per
shaft). Generally all shaft seals are under pressure with the pressure
gradient across the seal being from pumped fluid to atmosphere. The
exceptions will be single internally mounted or double seals where the
product recirculation (single internally mounted only) or flush pressure
is greater than the pump pressure, resulting in the pressure gradient
being reversed.
Mechanical seals meet the majority of application demands and of

these, single and single flushed seals are most frequently specified.
The application of double mechanical seals is increasing to meet both
process demands for higher sanitary standards and legislation
requirements, particularly those related to emissions.
The majority of proprietary mechanical seals available from seal

manufacturers have been designed for single shaft pump concepts,
such as Centrifugal and Liquid Ring pumps. These pump types do not
impose any radial or axial constraints on seal design. However on
Rotary Lobe type pumps the need to minimise the shaft extension
beyond the front bearing places significant axial constraints. If this
were extended, the shaft diameter would increase introducing a radial
constraint - because shafts on a rotary lobe pump are in the same
plane, the maximum diameter of the seal must be less than the shaft
centres. Most designs therefore can only accommodate ‘bespoke’ or
‘customised’ seal design. This is not done to take any commercial
advantage but it is as a consequence of the rotary lobe pump design
concept.

Pump sealing
There is often more than one Selection of shaft seals is influenced by many variables:
solution and sometimes no
ideal solution, therefore a • Shaft diameter and speed
compromise may have to be
considered. • Fluid to be pumped
Temperature - effect on materials?
- can interface film be maintained?
Viscosity - drag on seal faces?
- clogging of seal restricting movement?
- can interface film be established and
maintained?
- stiction at seal faces?
Fluid behaviour - does product shear, thin, thicken or
‘work’ - balling/carbonise?
maintained?
Solids - size?
- abrasiveness?
- density?
- clogging of seal restricting movement?
maintained?
Thermal stability - what, if any change?
Air reacting - what, if any change?
• Pressure - within seal limits?

- fluctuations?
- peaks/spikes?
- cavitation?
• Services - flush?
- pressure?
- temperature?
- continuity?
• Health and Safety - toxic?

- flammable?
- explosive?
- corrosive?
- irritant?
- carcinogenic?

Pump sealing
6.1 Mechanical Seals - General

Mechanical seals are designed for minimal leakage and represent the
majority of Centrifugal, Liquid Ring and Rotary Lobe pump sealing
arrangements.
Mechanical seal selection must consider:
• The materials of seal construction, particularly the sealing

faces and elastomers.
• The mounting attitude to provide the most favourable
environment for the seal.
• The geometry within which it is to be mounted.
A mechanical seal typically comprises of:
• A primary seal, comprising of stationary and rotary seal rings.

• Two secondary seals, one for each of the stationary and
rotary seal rings.
• A method of preventing the stationary seal ring from rotating.
• A method of keeping the stationary and rotary seal rings
together when they are not hydraulically loaded i.e. when
pump is stopped.
• A method of fixing and maintaining the working length.
The Primary Seal

Comprises of two flat faces, one rotating and one stationary, which
support a fluid film, thus minimising heat generation and subsequent
mechanical damage.
Commonly used material combinations are:
Carbon - Stainless Steel

Carbon - Silicon Carbide
Carbon - Tungsten Carbide
Silicon Carbide - Silicon Carbide
Tungsten Carbide - Tungsten Carbide

Pump sealing
The Secondary Seal

This is required to provide a seal between the primary seal rings and
the components with which they interface. Also it can provide a
cushion mounting for the seat ring to reduce any effects of mechanical
stress i.e. shock loads.
Types of secondary seal are:

• ‘O’ rings • Cups • Gaskets • Wedges
For Alfa Laval pump ranges the ‘O’ ring is the most commonly type of
secondary seal used. It’s simple and versatile concept is enhanced
with the following comprehensive material options:
• NBR • EPDM • FPM • PTFE • MVQ • FEP • Kalrez® • Chemraz®
These are fully described in section 5.3.
Mechanical Seal Face/’O’ Ring Material Availability
Rotary Stationary
Seal Face Seal Face Seal ‘O’Ring
Tungsten Carbide
Tungsten Carbide
Stainless Steel
Stainless Steel
Silicon Carbide
Silicon Carbide
Pump Type Pump Range

Carbon
Carbon
EPDM
PTFE
MVQ
FPM
NBR
FEP
Centrifugal/ LKH ü ü ü ü ü ü ü
Liquid ring LKH-Multistage ü ü ü ü ü ü ü
LKHP-High Pressure ü ü ü ü ü ü
LKHSP ü ü ü ü ü ü
LKHI ü ü ü ü ü ü
LKH-Ultra Pure ü ü ü ü
MR ü ü ü ü ü ü ü ü ü
Rotary Lobe SRU ü ü ü ü ü ü ü ü ü ü

SX (see note) ü ü ü ü ü ü ü
Note: SX1 pump has tungsten carbide seal faces, not silicon carbide seal faces.
Table 6.1a
Stationary Seal Ring Anti-Rotation

Ideally the selected device listed below will also allow for axial
resilience.
• Flats • Pins • Elastomer resilience • Press fit • Clamps
Rotary Seal Ring Drive

Ideally the selected device listed below will allow for a degree of axial
movement.
• Spring • Bellows • Physical positioning • Elastomer resilience

Pump sealing
One of the main causes of Working Length

seal failure is for the seal The ideal design should eliminate/minimise possibilities for error by
working length not being incorporating:
correctly maintained.
• Physical position i.e. step on shaft • Grub screws
Fig. 6.1a Typical single mechanical seal
used in rotary lobe pumps 7
Item Description
1 Stationary seal ring O-ring
2 Stationary seal ring
3 Rotary seal ring
4 Rotary seal ring O-ring
5 Wave spring
6 Drive ring
7 Grub screw
Working length
Fig. 6.1b Typical single mechanical seal

used in centrifugal pumps Impeller
2 Item Description
Drive ring 1 Stationary seal ring
3
4 2 Rotary seal ring
3 Spring
O-ring
5 1
Pump shaft 5 Rotary seal ring O-ring
Principle of Mechanical Seal Operation

Interface film The function of the assembly is a combination of the extreme primary
seal face flatness and applied spring force. Once the pump is
operational, hydraulic fluid forces combine with seal design features
i.e. balance, which push the seal faces together. This reduces the fluid
interface thickness to a minimum whilst increasing pressure drop,
Aprox. 1 mm
therefore minimising pumped fluid leakage.
Fig. 6.1c Principle of mechanical seal

operation

Pump sealing
Fig. 6.1d Principle of mechanical seal

operation
Spring force
Fluid
pressure
Stationary
seal ring
Rotating seal ring
The gap between the seal ring surfaces is enlarged to clarify the
principle of mechanical sealing.
Mechanical Seal Mounting

Most mechanical seals can be mounted externally or internally.
External Mechanical Seals

The majority of mechanical seals used on Alfa Laval pump ranges are
mounted externally, meaning that all the rotating parts of the
mechanical seal (i.e. part of the rotary seal ring, spring, drive ring etc)
are not in contact with the fluid to be pumped. The externally
mounted mechanical seal is considered easy to clean, as only the
inside of the stationary and rotary seal rings and there associated ‘o’
rings are in contact with the fluid being pumped. The R00 type
mechanical seals used on the SX rotary lobe pump range, described
in 6.2, are an exception to this, as it is the outside and not the inside
of the seal components that is in contact with the fluid being pumped.
Externally mounted seals have a lower pressure rating than the
equivalent seal mounted internally.
Fig. 6.1e Typical external shaft seal

Rotating parts
Fluid

Pump sealing
Internal Mechanical Seals

Some mechanical seals are mounted internally, meaning that most of
the rotating parts are in contact with the fluid being pumped. The
internal mechanical seal is designed with sufficient clearance around
the rotating parts so that it can be cleaned as efficiently as possible
and can withstand relatively high fluid pressures.
Fig. 6.1f Typical internal shaft seal
Rotating parts
Fluid
For the Alfa Laval pump ranges, both the externally and internally
mounted types of mechanical seal are available as single and single
flushed versions. The externally mounted mechanical seal on
Alfa Laval pump ranges is also available as a double flushed
mechanical seal for some pump models. The typical single, single
flushed and double flushed mechanical seal arrangements are
described as follows:
Single Mechanical Seal

This is the simplest shaft seal version, which has already been
described previously in this section. This seal arrangement is generally
used for fluids that do not solidify or crystallise in contact with the
atmosphere and other non-hazardous duties. For satisfactory
operation it is imperative the seal is not subjected to pressures
exceeding the maximum rated pressure of the pump. Also the pump
must not be allowed to run ‘dry’, thus avoiding damage to the seal
faces, which may cause excessive seal leakage.
Typical applications are listed below, but full product/fluid and

performance data must be referred to the seal supplier for verification.
• Alcohol • Animal Fat • Aviation Fuel • Beer • Dairy Creams

• Fish Oil • Fruit Juice • Liquid Egg • Milk • Shampoo
• Solvents • Vegetable Oil • Water • Yoghurt

Pump sealing
Single Flushed Mechanical Seal

The definition of ‘flush’ is to provide a liquid barrier or support to the
selected seal arrangement. This seal arrangement is generally used
for any of the following conditions:
• where the fluid being pumped can coagulate, solidify or

crystallise when in contact with the atmosphere.
• when cooling of the seals is necessary dependent upon the

fluid pumping temperature.
This seal arrangement used on externally mounted seals requires the

supply of liquid to the atmospheric side of the mechanical seal to flush
the seal area. The characteristics of the fluid being pumped and the
duty conditions will normally determine if a flush is necessary. When
selecting a flushing liquid you must ensure that it is chemically
compatible with the relevant materials of pump/seal construction and
fully compatible with the fluid being pumped. Consideration should be
given to any temperature limitations that may apply to the flushing
liquid to ensure that hazards are not created (i.e. explosion, fire, etc).
The flushing liquid is allowed to enter the seal housing at low pressure
i.e. 0.5 bar max (7 psi max) to act as a barrier.
This most basic flush system, sometimes referred to as quench,

provides liquid to the atmosphere side of the mechanical seal thereby
flushing away any product leakage. For the majority of pump models
the flushed seal comprises of the same stationary and rotating parts
as the single seal, with the addition of a seal housing having a flushing
connection and/or flushing tubes and a lip seal.
Fig. 6.1g Typical externally mounted
single flushed mechanical seal used in Item Description
rotary lobe pumps 12 1 Stationary seal ring O-ring
3 Rotary seal ring
5 Wave spring
6 Drive ring
7 Spacer O-ring
8 Spacer
9 Gasket
10 Seal housing
11 Lip seal
12 Grub screw

Pump sealing
Fig. 6.1h Typical externally mounted

single flushed mechanical seal used in
centrifugal pumps
Item Description
1 Seal housing
2 Lip seal
3 Flushing tubes

• Adhesive • Caramel • Detergent • Fruit Juice Concentrate • Gelatine

• Jam • Latex • Paint • Sugar Syrup • Toothpaste • Yeast
Double Flushed Mechanical Seal

This seal arrangement is generally used with hostile media conditions
i.e. high viscosity, fluid is hazardous or toxic. The double flushed seal
used on Alfa Laval pump ranges is basically two single mechanical
seals mounted ‘back to back’. This seal generally comprises of the
same stationary and rotating parts as the single seal for the majority
of pump models, with the addition of a seal housing having a flushing
connection and/or flushing tubes (dependent upon pump type). A
compatible flushing liquid is pressurised into the seal housing at a
pressure of 1 bar (14 psi) minimum above the discharge pressure of
the pump. This results in the interface film being the flushing liquid and
not the pumped liquid. Special attention is required in selecting seal
faces and elastomers.
The arrangement in contact with the pumped fluid is referred to as the

‘inboard seal’, and the seal employed for the flushing liquid is referred
to as the ‘outboard seal’. For Alfa Laval Centrifugal pumps the design
of the outboard seal differs to the inboard seal.
Fig. 6.1i Typical double flushed
mechanical seal used in rotary lobe 14 Item Description
pumps 1 Stationary seal ring O-ring
3 Rotary seal ring
5 Wave spring
6 Drive ring
7 Wave spring
Rotorcase Gearcase 9 Rotary seal ring
11 Gasket
12 Stationary seal ring O-ring
13 Seal housing
14 Grub screw

Pump sealing
Fig. 6.1j Typical double flushed

mechanical seal used in centrifugal
pumps
Item Description
1 Seal housing
2 Flushing tubes
4 Rotary seal ring

• Abrasive Slurries • Chocolate • Glucose • Hazardous Chemicals

• PVC Paste • Photographic Emulsion • Resin
General Seal Face Operating Parameters

Tables below show general parameters regarding viscosity and
temperature, which should be noted when selecting a mechanical
seal.
Table 6.1b
Viscosity Seal Face Combination
up to 4999 cP Solid Carbon v Stainless Steel

Solid Carbon v Silicon Carbide
Solid Carbon v Tungsten Carbide
up to 24999 cP Inserted Carbon v Stainless Steel
Inserted Carbon v Silicon Carbide
Inserted Carbon v Tungsten Carbide
up to 149999 cP Silicon Carbide v Silicon Carbide
Tungsten Carbide v Tungsten Carbide
above 150000 cP Consider Double Seals
Table 6.1c
Temperature Seal Face Combination
o
up to 150°C (302 F) Inserted Carbon v Stainless Steel
Silicon Carbide v Silicon Carbide
Tungsten Carbide v Tungsten Carbide
up to 200°C (392oF) Solid Carbon v Stainless Steel

Pump sealing
Flushing Pipework Layout

The suggested arrangement below is for single mechanical seals only.
If the pump is fitted with double mechanical seals or packed glands
the pressure gauges and control valves should be fitted on the outlet
side of the system. The choice of flushing liquid is dependent upon
compatibility with the pumping media and overall duty conditions i.e.
pressure and temperature. Usually water is used for cooling and any
water soluble products.
Fig. 6.1k Typical flushing pipework
layout for a rotary lobe pump *Pressure gauge * Double mechanical seal only
*Control valve
Pressure gauge
Control valve
Suggested visible
indication of flow
Flush inlet
Flush outlet to waste Check valve Isolation valve
Fig. 6.1l Typical flushing pipework layout

for a centrifugal pump Free outlet
Inlet

Pump sealing
Mechanical Seal Selection Process

The illustration below describes the mechanical seal selection process
with relevant questions to be answered.
Fig. 6.1m Seal selection process
Obtain all Product/Fluid
and Performance data
This should be used for

guidance purposes only, as Select Seal Type
actual seal selections should

be verified by the seal
suppliers. - Does fluid crystallise?
- Is cooling required?
- Will pump run dry?
- Is aseptic barrier Yes
required? Use Single Flushed Seal
No
- Is fluid hazardous?
- Is fluid abrasive?
- Is fluid viscosity high?
- Is temperature high? Yes
- Is aseptic barrier Use Double Flushed Seal
required?
No
Use Single Seal
Select Seal Materials
Select Seal Faces Select Elastomers
- Check viscosity - Check elastomer

limitations (see table compatibility (see
6.1b). guide in section
- Check temperature 14.10).
limitations (see table - Check temperature
6.1c). limitations.
- Is fluid abrasive?
- Check chemical
compatibility.

Pump sealing
6.2 Mechanical Seal Types in Alfa Laval

Pump Ranges
Seal Option Availability for Centrifugal and Liquid Ring Pumps
Pump Range External Mounting Internal Mounting

Single Single Flushed Double Flushed Single Single Flushed
LKH ü ü ü
LKH-Multistage ü ü
LKHP ü ü
LKHSP ü ü ü
LKHI ü ü
LKH-UltraPure ü ü
MR-166S, -200S ü
MR-300 ü
Table 6.2a
Seal Option Availability for Rotary Lobe Pumps

Table 6.2b
Mechanical Seal Type Seal Name Pump Range
SRU SX
Single externally mounted R90 ü

R00 ü
Hyclean ü
Single flushed externally mounted R90 ü
R00 ü
Hyclean ü
Single flushed internally mounted R90 ü
Double flushed R90 ü
R00 ü
R90 Type Mechanical Seals

The basic working principles of the R90 type mechanical seals have
previously been referred to in 6.1.
Hyclean Type Mechanical Seals

This seal arrangement is generally used for food and other hygienic
applications. The design of this seal incorporates a self-cleaning
feature.

Pump sealing
Fig. 6.2a Hyclean single mechanical seal

7
Item Description
1 Rotorcase O-ring
2 Wave Spring
3 Shaft O-ring
4 Stationary Seal Ring
5 Rotary Seal Ring
6 Washer
7 Clip
Front cover R00 Type Mechanical Seals

compression joint Cup seal The R00 type mechanical seals specifically designed for the SX rotary
lobe pump range are fully front loading seals and fully interchangeable
without the need for additional housings or pump component
changes. Specialised seal setting of the mechanical seal is not
required as the seal is dimensionally set on assembly. Seal faces
Spline sealing positioned in the fluid area minimise shear forces. All seals have
cup seal Squad ring
controlled compression joint elastomers at fluid/atmosphere
Fig. 6.2b SX pumphead sealing interfaces.
Fig. 6.2c R00 single mechanical seal
Item Description
1 Wave Spring
2 Squad Ring
1 2 3 4 5 3 Rotary Seal Ring
4 Cup Seal
5 Stationary Seal Ring

Pump sealing
6.3 Other Sealing Options (Rotary Lobe

Pumps only)
This is a simple, low cost, and Packed Gland
easy to maintain controlled The grade of packing used depends on the product being handled
leakage sealing arrangement. and operating conditions. When packed glands are specified, using
These are specified for many polyamide or PTFE packings will satisfy the majority of duties.
‘dirty’ applications, but when Provided the liquid being sealed contains no abrasive particles or
possible, should always be does not crystallise, gland packings will function satisfactorily on plain
avoided for sanitary duties, as stainless steel shafts or renewable stainless steel shaft sleeves. In
they are less hygienic than instances of moderately abrasive fluids, such as brine solutions being
mechanical seals. handled, the pumps should be fitted with hard coated shaft sleeves,
which may be easily replaced when worn. Pumps provided with a
packed gland seal are normally fitted with rubber slingers mounted
between the gland followers and the gearcase front lip seals. The
slingers will reduce the possibility of the product contacting the
gearcase lip seals, thereby overcoming any undesirable operating
conditions that could arise in this area. When correctly assembled and
adjusted, a slight loss of product should occur so as to lubricate the
packing and shaft or sleeve, if fitted.
Fig. 6.3a Packed gland
9 Item Description
1 Shaft sleeve O-ring
2 Shaft sleeve
3 Spacer
4 Packing rings
5 Gasket
6 Gland housing
7 Gland follower
8 Ring slinger
9 Grub screw
This seal arrangement is available on all SRU pump models.
Packed Gland with Lantern Ring

With fluids containing very abrasive particles or fluids that will
coagulate, solidify or crystallise in contact with the atmosphere, a
packed gland with lantern ring may be used. In such circumstances a
compatible liquid is supplied to the chamber formed by the lantern
ring at a pressure of at least 1 bar (14 psi) above the pump pressure.
The function of this liquid is to prevent, or at least inhibit, the entry of
abrasives into the very small clearances between the shaft and
packing. In the case of liquids which coagulate, solidify or crystallise in
contact with the atmosphere the flushing liquid acts as a dilutant and
barrier in the gland area preventing the pumped fluid from coming in
contact with the atmosphere.

Pump sealing
A disadvantage with this seal arrangement is that the flushing liquid

will pass into the product causing a relatively small degree of dilution/
contamination, which cannot always be accepted.
In common with all packed gland assemblies slight leakage must

occur but in this instance it will basically be a loss of flushing liquid as
opposed to product being pumped.
Fig. 6.3b Packed gland with lantern ring
10 Item Description
1 Shaft sleeve O-ring
2 Shaft sleeve
3 Spacer
4 Packing rings
5 Lantern ring
6 Gasket
7 Gland housing
8 Gland follower
9 Ring slinger
10 Grub screw
This seal arrangement is available on all SRU pump models.

Pump sealing

Pump Sizing
7. Pump Sizing
This section shows how to size an Alfa Laval pump from product/
fluid and performance data given, supported by relevant calculations
and worked examples with a simple step by step approach.
7.1 General Information Required

In order to correctly size any type of pump some essential
information is required as follows:
See section 2 for detailed Product/Fluid Data

descriptions of Product/Fluid • Fluid to be pumped.
data and Performance data. • Viscosity.
• SG/Density.
• Pumping temperature.
• Vapour pressure.
• Solids content (max. size and concentration).
• Fluid behaviour (i.e. Newtonian or Pseudoplastic etc.).
• Is product hazardous or toxic?
• Does fluid crystallise in contact with atmosphere?
• Is CIP required?
Performance Data
• Capacity (Flow rate).
• Discharge head/pressure.
• Suction condition (flooded or suction lift).
Site Services Data
• Power source (electric, air, diesel, petrol or hydraulic).
If electric - motor enclosure and electrical supply.
• Seal flushing fluid.
In an ideal situation all the above criteria should be known before

sizing a pump - however, in many instances not all of this information
is known and made available. In such cases to complete the sizing
process, some assumptions may need to be made based upon
application knowledge, experience etc. These should be subsequently
confirmed, as they could be critical to satisfactory installation and
operation.

Pump Sizing
7.2 Power
All of the system energy requirements and the energy losses in the
pump must be supplied by a prime mover in the form of mechanical
energy. The rate of energy input needed is defined as power and is
expressed in watts (W) - for practical purposes, power within this
handbook is expressed in kilowatts (kW), i.e. watts x 10³.
7.2.1 Hydraulic Power

The theoretical energy required to pump a given quantity of fluid
against a given total head is known as hydraulic power, hydraulic
horse power or water horse power.
This can be calculated as follows:
Hydraulic Power (W) = Q x H x r x g
where: Q = capacity (m3/s)

H = total head/pressure (m)
r = fluid density (kg/m³)
g = acceleration due to gravity (m/s2)
Other forms of this equation can be as follows:
Hydraulic Power (kW) = Q x H

k
where: Q = capacity
H = total head/pressure
k = constant (dependent upon units used)
Therefore
Hydraulic Power (kW) = Q x H

k
where: Q = capacity (l/min)

H = total head/pressure (bar)
k = 600

Pump Sizing
or
Hydraulic Power (hp) = Q x H

k
where: Q = capacity (US gall/min)

H = total head/pressure (psi)
k = 1715
or
Hydraulic Power (hp) = Q x H

k
where: Q = capacity (UK gall/min)

H = total head/pressure (psi)
k = 1428
7.2.2 Required Power

The required power or brake horsepower is the power needed at the
pump shaft. This is always higher than the hydraulic power due to
r = radius
energy losses in the pump mechanism (friction loss, pressure loss,
seals etc) and is derived from:
V=
velocity Required Power = wxT
where: w = shaft angular velocity
Fig. 7.2.2a Shaft angular viscosity T = Shaft Torque
Shaft angular velocity w = V x r
And is related to Hydraulic power by:
Required Power = Hydraulic Power

Efficiency (100% = 1.0)
The appropriate prime mover power must be selected. Generally this

will be the nearest prime mover rated output power above the
required power.

Pump Sizing
The power requirements for 7.2.3 Torque

mechanical devices such as Torque is defined as the moment of force required to produce
pumps and pump drives are rotation and is usually expressed in units of Nm (Newton metres),
best expressed in terms of Kgfm (Kilogram metres) or ftlb (foot pounds).
torque and speed.
Torque can be calculated as follows:
Torque (Nm) = Required power (kW) x 9550

Pump speed (rev/min)
or
Torque (Kgfm) = Required power (kW) x 974

or
Torque (ftlb) = Required power (hp) x 5250

It should be noted that rotary lobe pumps are basically constant

torque machines and therefore it is important that the transmission
chosen is capable of transmitting the torque required by the pump.
This is particularly important for variable speed drives which should
be selected initially on torque rather than power.
7.2.4 Efficiency
Total Efficiency
Total efficiency is typically used on centrifugal and liquid ring pumps to
describe the relationship between input power at the pump shaft and
output power in the form of water horsepower. The term ‘mechanical
efficiency’ can also be used to describe this ratio. Total efficiency,
designated by symbol h, comprises of three elements, Hydraulic
Efficiency (hh), Mechanical Efficiency (hm ) and Volumetric Efficiency (hv )
which are described below:
Hydraulic Efficiency
The term hydraulic efficiency is used on centrifugal and liquid ring type
pumps to describe one of the three elements of centrifugal and liquid
ring pump total efficiency as described above.
where Hydraulic Efficiency (hh)= Pump head loss (m) x 100%

Total head (m)
The pump head losses comprise of the shock loss at the eye of the
impeller, friction loss in the impeller blade and circulation loss at the
outlet side of the impeller blades.

Pump Sizing
Mechanical Efficiency
This term is used on all centrifugal, liquid ring and rotary lobe pump
types, and is typically used to describe the losses associated with the
transfer of energy from the prime mover through a mechanical
system to the pumped liquid.
where
Mechanical Efficiency (hm ) = 1 – Pump mechanical losses x 100%
Required power
Pump mechanical losses refers to the friction losses associated with

bearings, seals and other contacting areas within the pump.
Volumetric Efficiency
This term is used on all centrifugal, liquid ring and rotary lobe pump
types. It is most commonly used to compare the performance of a
number of pump types, where accurate geometric data is available.
For centrifugal and liquid ring pumps,
Volumetric Efficiency (hv) = Q x 100%

Q + QL
where: Q = Pump capacity.

Q L = Fluid losses due to leakage through the
impeller casing clearances.
For rotary lobe pumps the term volumetric efficiency (hv) is used to
compare the displacement of the pump against the capacity of the
pump. The displacement calculation (q) per revolution for rotary lobe
pumps involves calculating the volume of the void formed between
the rotating element and the fixed element of the pump. This is then
multiplied by the number of voids formed by a rotating element per
revolution of the pump’s drive shaft and by the number of rotors in
the pump.
For rotary lobe pumps,
Volumetric Efficiency (hv) = Q x 100%

q
where: Q = Pump capacity.

q = Pump displacement.

Pump Sizing
Rotary lobe pumps are generally highly efficient and even at viscosity
of 100 cP the volumetric efficiency of most pumps is approximately
90% for low pressure duties. At lower viscosities and/or higher
pressures the volumetric efficiency will decrease due to slip as
described in 8.6.1. Above 1000 cP, volumetric efficiency can be as
high as 95 - 99%. For these high viscosity duties, to select a pump
speed the following formulas can be used as a general guide.
n = Q x 100 where n = pump speed (rev/min)

q x hv x 60 Q = capacity (m³/h)
q = pump displacement (m³/100 rev)
hv = vol. efficiency (100% = 1.0)
or

q x hv Q = capacity (US gall/min)
q = pump displacement (US gall/100 rev)
or

q x hv Q = capacity (UK gall/min)
q = pump displacement (UK gall/100 rev)
Pump Efficiency
The term pump efficiency is used on all types of pumps to describe
the ratio of power supply to the drive shaft against water
horsepower.
Pump Efficiency hp = Water horse power x 100%

Required power
or
Pump Efficiency hp = QxHxrxg

wxT
where: Q = capacity (m³/s)

r = fluid density (kg/m³)
g = acceleration due to gravity (m/s²)
w = shaft angular velocity (rad/s)
T = shaft torque (Nm)

Pump Sizing
Overall Efficiency
Overall efficiency is a term used to describe and compare the
performance of all types of pump. Overall efficiency considers the
efficiency of both the prime mover and the pump, and is sometimes
known as the wire to water/liquid efficiency where the prime mover is
an electric motor.
Overall Efficiency hoa = Water horse power x 100%

Drive power

Pump Sizing
7.3 Centrifugal and Liquid Ring Pumps

In general the theory 7.3.1 Flow Curve
regarding sizing of centrifugal A centrifugal or liquid ring pump should always be sized from a pump
and liquid ring pumps is flow curve or a pump selection program. Most pump flow curves are
similar. based on tests with water. It is difficult to determine general curves
for fluids with viscosities different from water and therefore in these
instances it is recommended to use a pump selection program.
A pump flow curve specifies the connection between capacity Q,

head H, required power P, required NPSH and efficiency h.
Hydraulic Losses
The connection between the capacity and the theoretical head of the
pump is shown by means of a straight line, which decreases at a
higher capacity (see fig. 7.3.1a).
The actual head of a pump is, however, lower than the theoretical
head due to hydraulic losses in the pump, which are friction loss,
pressure loss and slip.
Fig. 7.3.1a Hydraulic losses
The connection between the capacity and actual head is consequently
specified by means of a curve which varies depending on the design
of the impeller.
Different Pump Characteristics

The capacity Q and head H curve of a centrifugal pump will vary
depending upon the impeller vane design (see fig. 7.3.1.b).
These fulfil different requirements and are well suited for flow control
where only one parameter is to be changed (see 7.3.2).
Curve 1 covers a wide range of heads without large changes to

Fig. 7.3.1b Curves for Q and H capacity.
Curve 3 covers a wide range of capacities without large changes to

head.

Pump Sizing
Curves for Capacity Q, Head H, Power P and Efficiency h

In principle the duty point of a pump can be situated at any point on
the Q-H curve.
The efficiency of the pump will vary depending on where the duty
point is situated on the Q-H curve. The efficiency is usually highest
near the centre of the curve.
Fig. 7.3.1c Curves for Q, H, P and h The power curve of the centrifugal pump increases at a higher
capacity.
The power curve of the liquid ring pump decreases at a higher

capacity.
NPSHr Curve
The NPSHr curve increases at higher capacity (see fig. 7.3.1d). This
should be used to assertain the NPSHr of the pump. It is important
that NPSHr of the pump exceeds the NPSHa of the system.
Fig. 7.3.1d NPSHr curve
Viscosity Effect
Fluid viscosity will affect capacity, head, efficiency and power (see fig.
7.3.1e).
• Capacity, head and efficiency will decrease at higher viscosities.

• Required power will increase at higher viscosities.
Fig. 7.3.1e Effects on Q, H and h
Density Effect
Fluid density will affect the head and required power which both
increase proportionally at higher density (see fig. 7.3.1f).
Fig. 7.3.1f Effects on Q, H and h

Pump Sizing
How to use the Flow Curve

The flow curve consists of three different curves:
• Head as a function of capacity (Q - H curve).

• Required power as a function of capacity (Q - P curve).
• Required NPSH as a function of capacity (Q - NPSHr curve).
Although illustrated here the efficiency is not shown on the published

flow curves but can be determined from the required power on the
flow curve and formula in 7.2 when the duty point is known.
The Q - H and Q - P curves are specified for different standard

impeller diameters so that a correct duty point can be determined.
This is not applicable to the LKH-Multistage pump and Liquid Ring
pumps as the impeller diameters cannot be reduced.
The curves on the flow curve are based on tests with water at 20°C
(68oF) with tolerances of + 5%. It is recommended to select the pump
by means of a pump selection program if the fluid to be pumped has
other physical properties.
Example: Product/Fluid Data:

Fluid to be pumped - Water.
Viscosity - 1 cP.
SG - 1.0
Pumping temperature - 20°C.
Performance Data:
Capacity - 15 m³/h.
Total head - 25 m.
Electrical supply - 220/380v, 50Hz.
The optimum is to select the smallest pump possible which is suitable

for the required duty point (15 m³/h, 25 m).

Pump Sizing
Step 1 - Find Appropriate Curve

Locate a flow curve for the required pump type that covers the duty
point. For this particular example a flow curve of a centrifugal pump
type LKH-10 with 3000 rev/min synchronous speed at 50Hz is
selected.
Fig. 7.3.1g Example
28
Step 2 - Look at Q - H curve

• Locate the capacity (15 m³/h) on the Q-scale.
• Start from this point and follow the vertical line upwards until it
intersects with the horizontal line indicating the required head
(25 m) on the H-scale.
• This duty point does not contact any curve corresponding to a
certain impeller diameter. Therefore, the nearest larger size impeller
diameter should be selected, in this case 150 mm.
• The head will then be 28 m.
• The selected head (28 m) should be checked regarding the lower
tolerance of the curve to ensure that it is at least the required
25 m.
• In this case the head should be reduced by 5% being the curve
tolerance.
• The head will then be a minimum of 26.6 m greater than 25 m,
thus satisfactory.

Pump Sizing
Step 3 - Look at Q - P curve

• The next step in selecting the pump is to follow the vertical
capacity line (15 m³/h) downwards until it intersects with the power
curve for the 150 mm impeller.
• A horizontal line to the left of the intersection indicates a required
power of 2.0 kW.
• For a LKH centrifugal pump a safety factor of 5% for motor losses
must be added, resulting in a total required power of 2.1 kW.
• Consequently a 2.2 kW motor can be used.
Step 4 - Look at Q - NPSHr curve

• Finally the vertical capacity line (15 m³/h) is followed up to the
NPSHr curve.
• The intersection corresponding to the 150 mm impeller is located.
• A horizontal line to the right of the intersection indicates that
NPSHr is approx. 0.8 m.
7.3.2 Flow Control

Duty Point
The duty point of a pump is the intersection point between the pump
curve and the process curve.
Pump curve - this specifies the connection between head H and

capacity Q (see 7.3.1).
Process curve - this specifies the connection between the total

pressure drop (DH) in the process plant and the capacity (Q) (see fig.
7.3.2a).
The process curve is determined by varying the capacity so that

different pressure drop (DH) values are obtained. The shape of the
process curve will depend on the process design (i.e. layout, valves,
filters etc.).
Capacity: Q1 Q2 Q3 Q4 Q5 Q6
Pressure drop: DH1 DH2 DH3 DH4 DH5 DH6
The duty point of a pump can change due to changes in the

conditions of the process plant (changes in head, pressure drops
etc.). The pump will automatically regulate the capacity to meet the
new conditions (see fig. 7.3.2b and 7.3.2c).
Fig. 7.3.2a Process curve

Pump Sizing
Fig. 7.3.2b Changes in pressure drop Fig. 7.3.2c Changes in required head
It is possible to compensate for the change of duty point by means of

flow control that can be achieved as follows:
• Reducing the impeller diameter (not for liquid ring pumps).

• Throttling the discharge line.
• Controlling the pump speed.
Due to flow control it is possible to achieve optimum pump efficiency

at the required capacity resulting in the most economical pump
installation.
Reducing Impeller Diameter

Reducing the impeller diameter can only be carried out for centrifugal
pumps and multi-stage centrifugal pumps. This will reduce the
capacity and the head.
Centrifugal Pump
The connection between impeller diameter (D), capacity (Q) and head
(H) is shown in fig. 7.3.2d:
Fig. 7.3.2d Reducing impeller diameter
1. Before reducing.
2. After reducing - the duty point moves towards point 2 when
reducing the impeller diameter.

Pump Sizing
If the impeller speed remains unchanged, the connection between

impeller diameter (D), capacity (Q), head (H) and required power (P) is
shown by the following formulas:
Ö Q [mm]
Q1 D13 3 Q2
Diameter/capacity: = Þ D2 = D1 x
3
Q2 D2 1
ÖH
H1 D12 H2
Diameter/head: = Þ D2 = D1 x [mm]
2
H2 D2 1
Ö H [mm]
P1 D15 5 H2
Diameter/power: = Þ D2 = D1 x
P2 D25 1
Most pump flow curves show characteristics for different impeller

diameters to enable the correct impeller diameter to be selected.
Reducing the impeller diameter by up to 20% will not affect the

efficiency of the pump. If the reduction in impeller diameter exceeds
20%, the pump efficiency will decrease.
Multi-stage Centrifugal Pump

This pump has several impellers depending upon pump type. The
total head can be adjusted by reducing the diameter of the back
c impeller, which is situated at the pump outlet (nearest to the back
b
plate). Consequently the exact duty point will be between the curves
of two pump sizes.
The connection between impeller diameter (D), capacity (Q), head (H)
Fig. 7.3.2e Reducing impeller diameter and type of pump is shown in fig. 7.3.2e.

Pump Sizing
The formula is for guidance The impeller diameter is reduced to D2 by means of the following
purposes only. It is, therefore, formula:
recommended to add a safety
Ö a-b [mm]
factor of 10-15% to the new c-b
diameter. D2 = D1 x
Where:
D1 = Standard diameter before reducing.
a = Max. duty point.
b = Min. duty point.
c = Required duty point.
Throttling Discharge Line

Throttling the discharge line will increase the resistance in the process
plant, which will increase the head and reduce the capacity. The
connection between capacity (Q) and head (H) when throttling is
shown in fig. 7.3.2f.
1. Before throttling.
2. After throttling, the duty point moves towards point 2.
Fig. 7.3.2f Throttling discharge line
Throttling should not be carried out in the suction line as cavitation
can occur.
Also throttling will reduce the efficiency of the process plant DH

shows the ‘waste’ of pressure at point 2.
Controlling Pump Speed

Changing the impeller speed will change the centrifugal force created
by the impeller. Therefore, the capacity and the head will also change.
The connection between capacity (Q) and head (H) when changing
the impeller speed is shown in fig. 7.3.2g.
1. Before reducing impeller speed.

Fig. 7.3.2g Controlling pump speed 2. After reducing impeller speed. The working point moves towards
point 2 when reducing the impeller speed.

Pump Sizing
The most common form of If the impeller dimensions remain unchanged, the connection between
speed control is by means of a impeller speed (n), capacity (Q), head (H) and required power (P) is
frequency converter (see 9.10). shown by the following formulas:
Q1 n1 Q2
Speed/capacity: = Þ n2 = n1 x [rev/min]
Q2 n2 Q1
ÖH
H1 n12 H2
Speed/head: = Þ n2 = n1 x [rev/min]
2
H2 n2 1
ÖP
P1 n13 3 P2
Speed/power: = Þ n2 = n1 x [rev/min]
3
P2 n2 1
As shown from the above formulas the impeller speed affects

capacity, head and required power as follows:
• Half speed results in capacity x 0.5.
• Half speed results in head x 0.25.
• Half speed results in required power x 0.125.
Speed control will not affect the efficiency providing changes do not
exceed 20%.
7.3.3 Alternative Pump Installations

Pumps Coupled in Series
It is possible to increase the head in a pump installation by two or
more pumps being coupled in series.
The capacity (Q) will always be constant throughout the pump series.
The head can vary depending on the pump sizes.
Fig. 7.3.3a Principle of connection The outlet of pump 1 is connected to the inlet of pump 2.
Pump 2 must be able to withstand the outlet head from pump 1.

Pump Sizing
If two different pumps are connected in series, the pump with the
lowest NPSH value should be installed as the first pump (for critical
suction conditions).
The capacity in the pump installation should not exceed the max.
capacity of the smallest pump. Otherwise there will be a pressure
drop in the smallest pump.
Fig. 7.3.3b Head of pumps in series A multi-stage centrifugal pump is in principle several pumps that are
coupled in series but built together as one pump unit.
Pumps Coupled in Parallel

It is possible to increase the capacity in a pump installation by two or
more pumps coupled in parallel.
Fig. 7.3.3c Principle of connection Fig. 7.3.3d Connection of two similar Fig. 7.3.3e Connection of two different
pumps pumps
The head (H) will always be constant in the pump installation. The
capacity can vary depending on the pump sizes.
The pumps receive the fluid from the same source and have a
common discharge line.
When the capacity is increased by means of pumps coupled in

parallel, the equipment and pressure drop in the installation must be
determined according to the total capacity of the pumps.
For two different pumps, If the capacity Q1 is smaller than the

Fig. 7.3.3f Connection of two different capacity Q2, it is possible to install a non-return valve in the discharge
pump sizes line of pump 1 to avoid pump 2 pumping fluid back through pump 1.

Pump Sizing
7.4 Worked Examples of Centrifugal Pump

Sizing (Metric units)
7.4.1 Example 1
The following example shows a pump to be sized for a typical
brewery process.
The pump is required to handle Wort from the Whirlpool to the

Fermentation vessel.
Yeast
CIP
CO2
CO2
Fermentation
CIP
CO2
CO2
0.6 bar
(pressure vessel)
Cooling
O2
21 m
Wort pump
Yeast pitching
Whirlpool
80 m
Fig. 7.4.1a Example 1
As described in 7.1 in order to correctly size any type of pump, some

essential information is required such as Product/Fluid data,
Performance data and Site Services data.

Pump Sizing
All the data has been given by Product/Fluid data:

the customer. Fluid to be pumped - Wort.
Viscosity - 1 cP.
Performance data:
Discharge - via 80 m of 101.6 mm dia. tube, plus a
given number of bends, valves and a plate
heat exchanger with DpPHE 1.6 bar.
Static head in Fermenting vessel = 21 m.
Pressure in Fermenting vessel = 0.6 bar.
Suction - 0.4 m head, plus a given number of bends
and valves.
Site Services data:

Electrical supply - 220/380v, 50 Hz.
Before sizing a pump, it will be necessary to determine the total head

and NPSHa. The theory, including the different formulae regarding
these parameters is more specifically described in 2.2.2 and 2.2.4.
Total head
Total discharge head Ht = ht +hft +pt
Where ht = Static head in Fermentation vessel.
hft = Total pressure drop in discharge line.
pt = Pressure in Fermentation vessel.
Therefore ht = 21 m.
hft = Pressure drop in tube Dptube + Pressure drop
Fig. 7.4.1b in bends and valves Dp + Pressure drop in
plate heat exchanger DpPHE
Dptube from curve shown in 14.5 = 2 m.
Dp is calculated to be 5 m.
DpPHE is given as 1.6 bar = 16 m.
hft = 2 + 5 + 16 m.
= 23 m.
pt = 0.6 bar = 6 m.
Ht = ht +hft +pt = 21 + 23 + 6 m = 50 m (5 bar).

Pump Sizing
Total suction head Hs = hs – hfs +ps

Where hs = Static suction head in Whirlpool.
hfs = Total pressure drop in suction line.
ps = Pressure in Whirlpool (open tank).
Therefore hs = 0.4 m.
hfs = calculated to be 1 m.
ps = 0 (open tank).
Hs = hs – hfs +ps = 0.4 – 1 + 0 m = – 0.6 m (– 0.06 bar).
Total head H = Ht – Hs = 50 – (– 0.6) = 50.6 m » 51 m (5.1 bar).
NPSHa
NPSHa = Pa + hs – hfs – Pvp
Where Pa = Pressure absolute above level of fluid in
Whirlpool tank.
hs = Static suction head in Whirlpool tank.
Pvp= Vapour pressure of fluid.
Therefore Pa = 1 bar (open tank) = 10 m.

hs = 0.4 m.
hfs = Calculated to be 1 m.
Pvp= 0.70 bar a (from table 14.4a) = 7 m.
NPSHa = 10 + 0.4 – 1 – 7 (m) = 2.4 m.
Actual pump sizing can be made using pump performance curves or

a pump selection program. The performance curves are, however,
not suitable if the fluid to be pumped has physical properties (i.e.
viscosity) different from water. In this particular example both the
pump performance curves and pump selection program can be used.
The performance curve selection procedure is more specifically
described in 7.3.1.
For this particular example, pump sized would be as follows:
Pump model - LKH-25.

Impeller size - 202 mm.
Speed - 2930 rev/min.
Head - 51.5 m (5.15 bar).
Efficiency - 63.1%.
NPSHr - 1.4 m.
Motor size - 11 kW.

Pump Sizing
Cavitation check:
NPSHa should be greater than NPSHr i.e. 2.4 m > 1.4 m,
i.e. no cavitation will occur.
The recommended shaft seal type based upon Alfa Laval application
experience and guidelines would be a double mechanical seal with
carbon/silicon carbide faces and EPDM elastomers.
1: Full vessel Special Note

2: Empty vessel The discharge head (ht2) is lower when the pump starts filling the
ht1 fermenting vessel compared to the discharge head (ht1) when the
1
vessel is full. The reduction of the discharge head can result in
ht2 2 cavitation and overloading of the motor due to a capacity increase.
Cavitation can be avoided by reducing the pump speed (reducing
NPSHr), i.e. by means of a frequency converter, or by throttling the
Q2
discharge line (increasing head). The flow control method is more
Fig. 7.4.1c specifically described in 7.3.2.
Adjustment
In this example the pump is sized by the pump selection program
which results in exact impeller diameter of 202 mm, so that the
selected duty point is as close to the required duty point as possible.
The pump is sized with a standard impeller diameter if using the

performance curve. In this case it may be necessary to adjust the
selected duty point by means of flow control.
It is important to note that the selected head has a tolerance of ± 5%

due to the tolerance of the pump curve. Consequently, there is a risk
that the pump will generate head which will differ from the selected
head. If the required head is the exact value of the process, it is
recommended to select the pump with a larger impeller diameter to
ensure the required head is obtained.
It may also be necessary to adjust to the required duty point by

means of flow control due to the tolerance. Flow control method is
more specifically described in 7.3.2.

Pump Sizing
7.4.2 Example 2
The following example shows a centrifugal pump to be sized for a
typical dairy process.
Pump ‘A’ is a Raw Milk pump in connection with a pasteuriser. The

raw milk is pumped from a Balance tank to a Separator via the
preheating stage in the plate heat exchanger.
CIP
Milk out
PHE
Pump ‘A’
Standardised Milk
Balance
Tank
Separator
P = 1.5 bar


the customer. Fluid to be pumped - Raw Milk.
Viscosity - 5 cP.
Performance data:
Discharge - via 5 m of horizontal 76 mm dia. tube, plus
a given number of bends, valves and a plate
heat exchanger with DpPHE 1 bar.
Inlet pressure for the separator = 1.5 bar.
Suction - 0.1 m head, plus a given number of bends
and valves.

Pump Sizing
Site Services data:


Total head
Where ht = Static head to Separator.
pt = Pressure in Separator.
Therefore ht = 0 m (no static head - only horizontal tube).

Dptube from curve shown in 14.5 = 2 m.
Dp is calculated to be 0 m.
DpPHE is given as 1.0 bar = 10 m.
hft = 2 + 0 + 10 m.
= 12 m.
pt = 1.5 bar = 15 m.
Ht = ht +hft +pt = 0 + 12 + 15 m = 27 m (2.7 bar).

Where hs = Static suction head in Balance tank.
ps = Pressure in Balance tank (open tank).
Therefore hs = 0.1 m.
hfs = calculated to be 0.4 m.
ps = 0 (open tank).
Hs = hs – hfs +ps = 0.1 – 0.4 + 0 m = – 0.3 m (– 0.03 bar).
Total head H = Ht – Hs = 27 – (– 0.3) = 27.3 m » 27 m (2.7 bar).

Pump Sizing
NPSHa
NPSHa = Pa + hs – hfs – Pvp.
Balance tank.
hs = Static suction head in Balance tank.

hs = 0.1 m.
hfs = Calculated to be 0.4 m.
Pvp= at temperature of 5oC this is taken as being
negligible i.e. 0 bar a = 0 m.
NPSHa = 10 + 0.1 – 0.4 – 0 (m) = 9.7 m.
As the fluid to be pumped has physical properties (i.e. viscosity)

different from water, the pump performance curves should not be
used, and actual pump sizing should be made using the pump
selection program.

Impeller size - 149 mm.
Head - 27.1 m (2.71 bar).
Efficiency - 65.9%.
NPSHr - 1.4 m.
Motor size - 4 kW.
Cavitation check:
NPSHa should be greater than NPSHr i.e. 9.7 m > 1.4 m,
experience and guidelines would be a single mechanical seal with

Pump Sizing
7.5 Worked Examples of Centrifugal Pump

Sizing (US units)
7.5.1 Example 1
The following example shows a pump to be sized for a typical
brewery process.
The pump is required to handle Wort from the Whirlpool to the

Fermentation vessel.
Yeast
CIP
CO2
CO2
Fermentation
CIP
CO2
CO2
9 psi
(pressure vessel)
Cooling
O2
69 ft
Wort pump
Yeast pitching
Whirlpool
262 ft


Pump Sizing
All the above data has been Product/Fluid data:

given by the customer. Fluid to be pumped - Wort.
Viscosity - 1 cP.
Pumping temperature - 194°F.
Performance data:
Capacity - 176 US gall/min.
Discharge - via 262 ft of 4 in dia. tube, plus a given
number of bends, valves and a plate heat
exchanger with DpPHE 23 psi.
Static head in Fermenting vessel = 69 ft.
Pressure in Fermenting vessel = 9 psi.
Suction - 1.5 ft head, plus a given number of bends

and valves.
Site Services data:


Total head
Where ht = Static head in Fermentation vessel.
pt = Pressure in Fermentation vessel.
Therefore ht = 69 ft.
Dptube from curve shown in 14.5 = 6 ft.
Dp is calculated to be 16 ft.
DpPHE is given as 23 psi = 53 ft.
hft = 6 + 16 + 53 ft.
= 75 ft.
pt = 9 psi = 20 ft.
Ht = ht +hft +pt = 69 + 75 + 20 ft = 164 ft (71 psi).

Pump Sizing

Where hs = Static suction head in Whirlpool.
ps = Pressure in Whirlpool (open tank).
Therefore hs = 1.5 ft.

hfs = calculated to be 3 ft.
ps = 0 (open tank).
Hs = hs – hfs +ps = 1.5 – 3 + 0 m = – 1.5 ft (– 0.6 psi).
Total head H = Ht – Hs = 164 – (– 1.5) = 165.5 ft » 166 ft (72 psi).
NPSHa
Whirlpool tank.
hs = Static suction head in Whirlpool tank.
Therefore Pa = 14.7 psi (open tank) = 33.9 ft.

hs = 1.5 ft.
hfs = Calculated to be 3 ft.
Pvp= 10 psia (from table 14.4a) = 23 ft.
NPSHa = 33.9 + 1.5 – 3 – 23 (ft) = 9.4 ft.

a pump selection program. The performance curves are, however,
not suitable if the fluid to be pumped has physical properties (i.e.
viscosity) different from water. In this particular example both the
pump performance curves and pump selection program can be used.
The performance curve selection procedure is more specifically
described in 7.3.1.

Impeller size - 6.50 in.
Head - 166.2 ft (72 psi).
Efficiency - 67.2%.
NPSHr - 7.5 ft.
Motor size - 15 hp.

Pump Sizing
Cavitation check:
NPSHa should be greater than NPSHr i.e. 9.4 ft > 7.5 ft,
experience and guidelines would be a double mechanical seal with
1: Full vessel Special Note

2: Empty vessel The discharge head (ht2) is lower when the pump starts filling the
ht1
1 fermenting vessel compared to the discharge head (ht1) when the
vessel is full. The reduction of the discharge head can result in
ht2 2 cavitation and overloading of the motor due to a capacity increase.
Cavitation can be avoided by reducing the pump speed (reducing
NPSHr), i.e. by means of a frequency converter, or by throttling the
Q2
discharge line (increasing head). The flow control method is more
Fig. 7.5.1c specifically described in 7.3.2.
Adjustment
In this example the pump is sized by the pump selection program
which results in exact impeller diameter of 6.50 in, so that the
selected duty point is as close to the required duty point as possible.
The pump is sized with a standard impeller diameter if using the

performance curve. In this case it may be necessary to adjust the
selected duty point by means of flow control.
It is important to note that the selected head has a tolerance of ± 5%

due to the tolerance of the pump curve. Consequently, there is a risk
that the pump will generate head which will differ from the selected
head. If the required head is the exact value of the process, it is
recommended to select the pump with a larger impeller diameter to
ensure the required head is obtained.
It may also be necessary to adjust to the required duty point by

means of flow control due to the tolerance. Flow control method is
more specifically described in 7.3.2.

Pump Sizing
7.5.2 Example 2
The following example shows a centrifugal pump to be sized for a
typical dairy process.
Pump A is a Raw Milk pump in connection with a pasteuriser. The

raw milk is pumped from a Balance tank to a Separator via the
preheating stage in the plate heat exchanger.
CIP
Milk out
PHE
Pump ‘A’
Standardised Milk
Balance
Tank
Separator
P = 22 psi


the customer. Fluid to be pumped - Raw Milk.
Viscosity - 5 cP.
Performance data:
Discharge - via 16 ft of horizontal 3 in dia. tube, plus a
given number of bends, valves and a plate
heat exchanger with DpPHE 15 psi.
Inlet pressure for the separator = 22 psi.
Suction - 0.3 ft head, plus a given number of bends
and valves.

Pump Sizing
Site Services data:


Total head
Where ht = Static head to Separator.
pt = Pressure in Separator.
Therefore ht = 0 ft (no static head - only horizontal tube).

Dptube from curve shown in 14.5 = 6 ft.
Dp is calculated to be 0 ft.
DpPHE is given as 15 psi = 34 ft.
hft = 6 + 0 + 34 ft.
= 40 ft.
pt = 22 psi = 50 ft.

Where hs = Static suction head in Balance tank.
ps = Pressure in Balance tank (open tank).
Therefore hs = 0.3 ft.

hfs = calculated to be 1.3 ft.
ps = 0 (open tank).
Hs = hs – hfs +ps = 0.3 – 1.3 + 0 m = – 1 ft (– 0.4 psi).
Total head H = Ht – Hs = 90 – (– 1) = 91 ft (39 psi).

Pump Sizing
NPSHa
NPSHa = Pa + hs – hfs – Pvp
Balance tank.
hs = Static suction head in Balance tank.

hs = 0.3 ft.
hfs = Calculated to be 1.3 ft.
Pvp= at temperature of 41o F this is taken as being
negligible i.e. 0 psia = 0 ft.
NPSHa = 33.9 + 0.3 – 1.3 – 0 (ft) = 32.9 ft.
As the fluid to be pumped has physical properties (i.e. viscosity)

different from water, the pump performance curves should not be
used, and actual pump sizing should be made using the pump
selection program.

Impeller size - 5.59 in.
Head - 92 ft (40 psi).
Efficiency - 64.7%.
NPSHr - 4.7 ft.
Motor size - 5.0 hp.
Cavitation check:
NPSHa should be greater than NPSHr i.e. 32.9 ft > 4.7 ft,
experience and guidelines would be a single mechanical seal with

Pump Sizing

7.6.1 Slip
Slip is the fluid lost by leakage through the pump clearances. The
direction of slip will be from the high pressure to the low pressure side
of the pump i.e. from pump outlet to pump inlet. The amount of slip is
dependent upon several factors.
Fig. 7.6.1a Slip
Slip
Inlet Outlet
Slip
Slip
Low pressure High Pressure
Clearance effect
Increased clearances will result in greater slip. The size and shape of
the rotor will be a factor in determining the amount of slip.
Pressure effect
The amount of slip will increase as pressure increases which is shown
below. In Fig 7.6.1b for a given pump speed the amount of slip can be
seen as the capacity at ‘zero’ bar less the capacity at ‘X’ bar. To
overcome this amount of slip it will be necessary to increase the
pump speed to maintain the capacity required as shown in Fig 7.6.1c.
‘0’ bar ‘X’ bar
Capacity ‘0’ bar
Required capacity
Capacity
Capacity at
Slip
‘X’ bar
‘0’ bar
Speed
increase to
Actual capacity maintain capacity
at ‘X’ bar
Speed rev/min
Speed rev/min
Fig. 7.6.1b Pressure effect Fig. 7.6.1c Pressure effect

Pump Sizing
Viscosity effect
The amount of slip will decrease as fluid viscosity increases. The effect
of viscosity on slip is shown in Figs 7.6.1d, 7.6.1e and 7.6.1f below.
The pressure lines will continue to move towards the ‘zero’ pressure
line as the viscosity increases.
‘0’ bar ‘X’ bar ‘0’ bar ‘X’ bar ‘0’ bar ‘X’ bar
Viscosity = 1 cP Viscosity = 10 cP Viscosity = 50 cP
Required Required Required

capacity capacity capacity
Capacity
Capacity
Capacity
Speed - rev/min Speed - rev/min Speed - rev/min
Fig. 7.6.1d Viscosity effect Fig. 7.6.1e Viscosity effect Fig. 7.6.1f Viscosity effect
Pump Speed effect

Slip is independent of pump speed. This factor must be taken into
consideration when operating pumps at low speeds with low
viscosity fluids. For example, the amount of slip at 400 rev/min pump
speed will be the same as the amount of slip at 200 rev/min pump
speed providing pressure is constant.
0 bar 7 bar
Capacity
Dead head Speed rev/min

speed
Fig. 7.6.1g Dead head speed
The pump speed required to overcome slip is known as the

‘dead head speed’.
It is important to note that flow will be positive after overcoming the

dead head speed.

Pump Sizing
A summary of effects of different parameters on slip is shown below:
Slip
Slip increases with pressure
Pressure
Fig. 7.6.1h
Slip
Slip increases with clearances
Clearances
Fig. 7.6.1i
SRU pump
Slip
Slip decreases with viscosity

SX pump
Viscosity
Fig. 7.6.1j
In general terms it is common 7.6.2 Initial Suction Line Sizing

to find the recommendation For guidance purposes only on high viscosity duties, the suction line
for the inlet pipe size to be the can be initially sized using the initial suction line sizing curve (see 14.9)
same diameter as the pump where the relationship between viscosity and flow rate provides an
inlet connection. indication of pipe sizing.
For example, for a flow rate of 10 m³/h on a fluid with viscosity

900 cSt, a pump with 40 mm (1½ in) diameter suction line would be
initially selected.
It is important to note this is only an approximate guide and care

should be taken not to exceed the pump’s viscosity/speed limit.

Pump Sizing
7.6.3 Performance Curve

Alfa Laval rotary lobe pumps can be sized from published
performance curves or a pump selection program. Due to pumphead
clearances described in 8.2.2, different performance curves are used
for the various temperature ratings for rotors i.e. 70°C (158oF),
130°C (266oF) and 200°C (392oF). The SX pump range has only
150°C (302oF) rotor temperature rating. For convenience viscosity
units are stated as cSt.
How to use the Performance Curve

The performance curve consists of four different curves:
• Capacity as a function of speed, related to pressure and viscosity.

• Power as a function of speed, related to pressure and viscosity
of 1 cSt.
• Power as a function of viscosity greater than 1 cSt.
• Speed as a function of viscosity.
The curves are based on water at 20°C (68oF) but are shown with
calculated viscosity correction data. Example shown refers to the
SRU pump range but the same sizing procedure is also used for the
SX pump range.

Pump Sizing
Example: Product/Fluid Data:

Fluid to be pumped - Vegetable Oil.
Viscosity - 100 cSt.
SG - 0.95
Performance Data:
Capacity - 3.6 m³/h (15.8 US gall/min).
Total Pressure - 8 bar (116 psig).
The optimum is to size the smallest pump possible as hydraulic

conditions dictate. However other factors such as fluid behaviour,
solids etc. should be considered.
Step 1 – Find Appropriate Curve

Locate a curve for the required pump model that covers the
performance data. Due to the large number of curves available it is
not practical to include all performance curves in this handbook.
Curves can be obtained from the pump supplier. However, the sizing
process would be as follows:
From the initial suction line sizing curve (see 14.9), a pump with a size
25 mm (1 in) inlet connection would be required. Although the
smallest pump models SRU1/005 and SRU1/008 have 25 mm (1 in)
pump inlet connections, the flow rate required would exceed the
pumps speed limit on the performance curve. For this particular
example, we therefore need to select a performance curve for the
pump model SRU2/013/LS with 70°C (158oF) rotor clearances, as
shown in Fig. 7.6.3a, being the next appropriate pump size.

Fig. 7.6.3a SRU2/013/LS curves
Typical Performance Curve

SRU2/013/LS or HS
US GPM m 3/h
Pump Sizing
350 172 110 78 58 43 32 23 16 9 X 100
25 mm (1 in)
Port
Pump Sizing
Step 2 - Find Viscosity and Pressure

Begin with viscosity and find the intersection point with duty pressure.
From example - 100 cSt and 8 bar (115 psig).
Step 3 - Find Flow Rate

Move diagonally downward and find intersection with required flow
rate.
From example – 3.6 m³/h (15.8 US gall/min).
Step 4 - Find Speed

Move vertically downward to determine necessary pump speed.
From example - 600 rev/min.
Step 5 - Viscosity/Port Size Check

Move vertically downward and check that maximum viscosity rating
has not been exceeded against relevant inlet size.
From example - maximum viscosity rating 4300 cSt.
Step 6 - Find Power

The power required by a pump is the summation of the hydraulic
power and various losses that occur in the pump and pumping
system. Viscosity has a marked effect on pump energy losses. The
losses being due to the energy required in effecting viscous shear in
the pump clearances. Viscous power is the power loss due to
viscous fluid friction within the pump (Pv factor).
Typically curves are used in conjuction with equation as follows:
Total Required Power (kW) =

Pv x Pump speed (rev/min) + Hydraulic power at 1 cSt (kW)
10000
where Pv = Power/viscosity factor
From example:
• At speed 600 rev/min the hydraulic power at 1 cSt is 1.3 kW,
• At viscosity 100 cSt the Pv factor is 1.0

Pv x Pump speed (rev/min) + Hydraulic power at 1 cSt (kW)
10000
= 1.0 x 600 + 1.3

10000
= 1.36 kW

Pump Sizing
It should be noted, this is the power needed at the pump shaft and
the appropriate motor power must be selected, which in this instance
would be 1.5 kW being the nearest motor output power above the
required power.
Step 7 - Find NPSHr

NPSHr can be found by looking at the appropriate NPSH pump
curve, which is a function of speed and expressed in metres water
column (mwc) or feet (ft).
50
100000 cSt
60000 cSt
45 30000 cSt
20000 cSt
40
10000 cSt
35
5000 cSt
30
2500 cSt
25
20
1000 cSt
15 4.4
14.4
10 1 cSt
0
Metres
Water
Water
Feet
Speed rev/min
Fig. 7.6.3b SRU2 typical NPSHr curve

based on water
From example - at speed 600 rev/min the NPSHr is 4.4 mwc

(14.4 ft).

Pump Sizing
7.6.4 Pumps fitted with Bi-lobe Rotors (Stainless Steel)

These rotors, described in 8.2.1, are mainly used on high viscosity
products containing solids where the pumps volumetric efficiency is
high. When pumping such products optimum performance is
obtained by using large slow running pumps.
Applications on water like viscosity fluids would result in decreased

efficiency over stainless steel tri-lobe rotors. For sizing purposes a
percentage increase on the ‘dead head speed’ (see table below)
should be applied to the performance curve for stainless steel tri-lobe
rotors and interpolated accordingly.
Table 7.6.4a
SRU Pump Model %age Increase Required on Tri-lobe
Rotor Dead Head Speed
SRU1/005 40
SRU1/008 40
SRU2/013 40
SRU2/018 40
SRU3/027 30
SRU3/038 30
SRU4/055 30
SRU4/079 25
SRU5/116 25
SRU5/168 10
SRU6/260 10
SRU6/353 10

Pump Sizing
Example of How to Interpolate Performance Curve

‘X’ rev/min represents the ‘dead head speed’ for tri-lobe rotors to
which a percentage increase is applied from the table shown. Pump
speed for bi-lobe rotors is found accordingly.
Fig. 7.6.4a Performance curve
interpolation Capacity 0 bar 7 bar
7 bar
Required capacity
Speed rev/min
‘X’ rev/min
Dead head speed

‘X’ rev/min + % inc.
Speed required for tri-lobe rotors
Speed required for bi-lobe rotors
7.6.5 Pumps fitted with Bi-lobe Rotors (Non Galling Alloy)

These rotors, described in 8.2.1, have very small clearances resulting
in increased volumetric efficiency over stainless steel rotors when
used on fluids with viscosities up to 50 cP. Pump sizing is achieved
by referring to published performance curves or a pump selection
program. Due to pumphead clearances described in 8.2.2, different
performance curves are used for the various temperature ratings of
rotors i.e. 70°C (158°F), 130°C (266°F) and 200°C (392°F). The use
of performance curves is as described in 7.6.3.
7.6.6 Pumps fitted with Tri-lobe Rubber Covered Rotors

These rotors, described in 8.2.1, have minimal clearance and will
therefore significantly improve the pumps volumetric efficiency to
approx. 95%. Pump sizing is achieved by referring to published
performance curves or a pump selection program. Due to the minimal
pumphead clearances described in 8.2.2, there is only one
temperature rating of rotors i.e. 70°C (158°F). The use of
performance curves is as described in 7.6.3.

Pump Sizing
7.6.7 Pumps with Electropolished Surface Finish

Pump performance will be affected by electropolish surface finish to
the pump head internals. For sizing purposes a percentage increase
on the ‘dead head speed’ (see tables below) should be applied to the
performance curve for stainless steel tri-lobe rotors and interpolated
accordingly.
Table 7.6.7a
Pump Model %age Increase Required on Stainless Steel
Tri-lobe Rotor Dead Head Speed
SRU range Electropolishing Mechanical and
only Electropolishing
1/005 17.0 60.0

1/008 15.1 55.0
2/013 10.8 45.8
2/018 8.5 38.0
3/027 6.7 32.7
3/038 5.5 28.5
4/055 4.6 24.8
4/079 3.8 21.0
5/116 2.9 18.0
5/168 2.4 15.5
6/260 2.0 12.8
6/353 1.7 11.4
Table 7.6.7b
Pump Model %age Increase Required on Multi-lobe
Rotor Dead Head Speed
SX range Electropolishing Mechanical and
only Electropolishing
1/005 12.0 60.0

1/007 9.3 47.6
2/013 8.3 40.9
2/018 7.7 38.4
3/027 6.9 34.0
3/035 6.2 31.3
4/046 5.6 28.6
4/063 5.0 25.5
5/082 4.5 22.8
5/116 4.0 19.3
6/140 3.5 17.0
6/190 2.9 14.0
7/250 2.2 11.3
7/380 1.3 6.8

Pump Sizing
7.6.8 Guidelines for Solids Handling
The following criteria should be considered when deciding the pumps

ability to handle large solids in suspension.
Optimum Conditions
Solids form - Spherical
Solids physical properties i.e. - Soft, yet possess resilience

hardness, Resilience, shear and shear strength
strength
Solids surface finish - Smooth
Fluid/solids proportion - Proportion of solids to fluid is

small
Relationship of fluid/solid SG - Equal
Flow velocity (pump speed) - Maintained such that solids in

suspension are not damaged
Rotor form - Bi-lobe
Port size - Large as possible
Tables below show the maximum spherical solids size that can be
satisfactory handled without product degradation, providing the
optimum conditions are met. For non-optimum conditions these
should be referred to Alfa Laval.
Table 7.6.8a
SRU Model Maximum Spherical Solids Size
Bi-lobe Rotors Tri-lobe Rotors
mm in mm in
SRU1/005 8 0.31 6 0.24

SRU1/008 8 0.31 6 0.24
SRU2/013 8 0.31 6 0.24
SRU2/018 13 0.51 9 0.34
SRU3/027 13 0.51 9 0.34
SRU3/038 16 0.63 11 0.44
SRU4/055 16 0.63 11 0.44
SRU4/079 22 0.88 15 0.59
SRU5/116 22 0.88 15 0.59
SRU5/168 27 1.06 18 0.72
SRU6/260 27 1.06 18 0.72
SRU6/353 37 1.47 24 0.94

Pump Sizing
Table 7.6.8b
SX Model Maximum Spherical Solids Size
Multi-lobe Rotors
mm in
SX1/005 7 0.28
SX1/007 7 0.28
SX2/013 10 0.39
SX2/018 10 0. 39
SX3/027 13 0.51
SX3/035 13 0.51
SX4/046 16 0.63
SX4/063 16 0.63
SX5/082 19 0.75
SX5/116 19 0.75
SX6/140 25 0.98
SX6/190 25 0.98
SX7/250 28 1.10
SX7/380 28 1.10
7.6.9 Guidelines for Pumping Shear Sensitive Media

Special attention needs to be made to pumping shear sensitive media
such as yeast and yoghurt where the cell structure needs to remain
intact. Excess pump speed can irreversibly damage the cell structure.
Therefore pump speeds need to be kept relatively low, in the range of
100 to 400 rev/min dependent upon the fluid being pumped, pump
size/model and rotor form. For these types of applications refer to
Alfa Laval.

Pump Sizing
7.7 Worked Examples of Rotary Lobe

Pump Sizing (Metric units)
The following examples show two different rotary lobe pumps to be
sized for a typical sugar process.
Pump 1 is a low viscosity example handling sugar syrup.

Pump 2 is a high viscosity example handling massecuite.
As described in 7.1 in order to correctly size any type of pump,

information is required such as Product/Fluid data, Performance data
and Site Services data.
Pump 1 – Thin Sugar Syrup pump
Fig. 7.7a Pump 1 - example

1 bar
1m
Feed tank
8m
1m 6m
1m 2m
3m
1m

the customer. Fluid to be pumped - Sugar syrup.
Viscosity - 80 cP.
SG - 1.29.
CIP temperature - 95°C.
Performance data:
Capacity - 9 m³/h.
Discharge - via 10 m of 51 mm dia. tube, plus 1 bend
90 deg. and 1 butterfly valve
Static head in vessel = 8 m.
Pressure in vessel = 1 bar.
Suction - via 3 m of 51 mm dia. tube, plus 2 bends
90 deg. and 1 non-return valve.
Static head in tank = 2 m.
Site Services data:

Pump Sizing

Total head
Where ht = Static head in pressurised vessel.
pt = Pressure in vessel.
Therefore ht = 8 m x (SG = 1.29) = 10.3 m.

Fig. 7.7b in bends and valves Dp (calculated below).
pt = 1 bar = 10 m.
To ascertain hft the flow characteristic and equivalent line length must
be determined as follows:
Flow Characteristic
Reynolds number Re = D x V x r
m
where D = tube diameter (mm).

r = density (kg/m³).
m = absolute viscosity (cP).
velocity V = Q x 353.6 where Q = capacity (m³/h).

D² D = tube diameter (mm).
= 9 x 353.6
51²
= 1.22 m/s
density r = 1290 derived from SG value 1.29 (see 2.1.5).
Therefore Re = D x V x r
m
= 51 x 1.22 x 1290
80
= 1003
As Re is less than 2300, flow will be laminar.

Pump Sizing
Equivalent Line Length – Discharge Side

The equivalent lengths of straight tube for bends and valves are taken
from table 14.7.1. Since flow is laminar, the viscosity correction factor
is 1.0 (see 2.2.2).
Straight tube length =3+6+1 = 10 m

1 bend 90 deg. = 1 x 1 x 1.0 (corr. factor) =1m
1 butterfly valve = 1 x 1 x 1.0 (corr. factor) =1m
Total equivalent length = 12 m
Also as flow is laminar the friction factor fD = 64

Re
= 64
1003
= 0.064
The Miller equation is now used to determine friction loss as follows:
Pf = 5 x SG x fD x L x V² (bar)
D
Where: Pf = pressure loss due to friction (hft)

fD = friction factor.
= 5 x 1.29 x 0.064 x 12 x 1.22² (bar)

51
= 0.14 bar = 1.4 m
Ht = ht +hft +pt = 10.3 + 1.4 + 10 m = 21.7 m (2.17 bar).
Total suction head Hs = hs – hfs + ps
Where hs = Static suction head in Tank.

ps = Pressure in Tank (open tank).
Therefore hs = 2 m x (SG = 1.29) = 2.6 m.

hfs = Calculated below.
ps = 0 (open tank).

Pump Sizing
Equivalent Line Length – Suction Side

is 1.0 (see 2.2.2).
Straight tube length =1+1+1 =3m

2 bend 90 deg. = 2 x 1 x 1 (corr. factor) =2m
1 non-return valve = 1 x 12 x 1 (corr. factor) = 12 m

Re
= 64
1003
= 0.064
D
Where: Pf = pressure loss due to friction (hfs)

= 5 x 1.29 x 0.064 x 1.7 x 1.22² (bar)

51
= 0.2 bar = 2 m
Hs = hs – hfs + ps = 2.6 – 2 + 0 m = 0.6 m (0.06 bar).
Total head H = Ht – Hs = 21.1 – 0.6 = 21.1 m » 21 m (2.1 bar)

Pump Sizing
NPSHa
Where Pa = Pressure absolute above fluid level in Tank.
hs = Static suction head in Tank.

hs = 2.6 m.
hfs = calculated to be 2 m.
Pvp= at temperature of 15o C this is taken as being
NPSHa = Pa + hs – hfs – Pvp = 10 + 2.6 – 2 – 0 m = 10.6 m.

a pump selection program. The performance curve selection
procedure is more specifically described in 7.6.3.
40 mm inlet connection would be required. Although the smallest
pump models SR1/008 (with enlarged port), SRU2/013 (with
enlarged port) and SRU2/018 (with sanitary port) have 40 mm pump
inlet connections, the flow rate required would exceed the pumps
speed limit on the performance curve. We have therefore selected a
performance curve for the pump model SRU3/027/LS with 130°C
rotor clearances due to the CIP requirement, being the next
appropriate pump size. Pump sized as follows:
Pump model - SRU3/027/LS.

Connection size - 40 mm.
NPSHr - 3.6 m.
Cavitation check:
NPSHa should be greater than NPSHr i.e. 10.6 m > 3.6 m.
Viscosity/Port Size check:

The viscosity of 80 cP at speed 606 rev/min is well within the pump’s
maximum rated figures.

Pump Sizing
Power calculation:
Pv x Pump speed (rev/min) + Power at 1 cSt (kW)
10000
where Pv = Power/viscosity factor.
From example
• At speed 606 rev/min and total head 2.1 bar, the power at
1 cSt is 0.9 kW,
• At viscosity 80 cP (62 cSt) the Pv factor is 3.

10000
= 3 x 606 + 0.9
10000
= 1.1 kW
It should be noted that this is the power needed at the pump shaft,
and the appropriate motor power must be selected, which in this
instance would be 1.5 kW being the nearest motor output power
above the required power.
The recommended type of shaft seal based upon Alfa Laval

application experience and guidelines would be a single flushed
mechanical seal with tungsten carbide/tungsten carbide faces and
EPDM elastomers.
• Hard tungsten carbide seal faces due to the abrasive nature of

sugar syrup.
• Flushed version to prevent the sugar syrup from crystallising
within the seal area.
• EPDM elastomers for compatibility of both sugar syrup and CIP
media.

Pump Sizing
Pump 2 – Massecuite pump
Fig. 7.7c Pump 2 - example
20 m
2m
1m 40 m

the customer. Fluid to be pumped - Massecuite.
Viscosity - 25000 cP.
SG - 1.35
Performance data:
Discharge - via 40 m of 76 mm dia. tube, plus 2 bends
Suction - via 1 m of 101.6 mm dia. tube, plus 1 bend
90 deg. and 1 butterfly valve.
Site Services data:



Pump Sizing
Total head
Therefore ht = 20 m x (SG = 1.35) = 27 m.

Fig. 7.7d in bends and valves Dp (calculated below).
pt = 0 bar (open tank) = 0 m.
Flow Characteristic
m


= 10 x 353.6
76²
= 0.61 m/s
Therefore Re = D x V x r
m
= 76 x 0.61 x 1350
25000
= 2.5

Pump Sizing

is 0.25 (see 2.2.2).
Straight tube length = 40 m

2 bend 45 deg. = 2 x 1 x 0.25 (corr. factor) = 0.5 m
1 butterfly valve = 1 x 2 x 0.25 (corr. factor) = 0.5 m

Re
= 64
2.5
= 25.6
D

= 5 x 1.35 x 25.6 x 41 x 0.61² (bar)

76
= 34.7 bar = 347 m
Ht = ht +hft +pt = 27 + 347 + 0 m = 374 m (37.4 bar).

Therefore hs = 2 m x (SG = 1.35) = 2.7 m.

ps = 0 (open tank).

Pump Sizing
To ascertain hfs the flow characteristic and equivalent line length must
Flow Characteristic
m


= 9 x 353.6
101.6²
= 0.34 m/s
Therefore Re = DxVxr
m
= 101.6 x 0.34 x 1350

25000
= 1.9

is 0.25 (see 2.2.2).

Pump Sizing
Straight tube length =1m

1 bend 90 deg. = 1 x 2 x 0.25 (corr. factor) = 0.5 m
1 butterfly valve = 1 x 2 x 0.25 (corr. factor) = 0.5 m
Total equivalent length =2m

Re
= 64
1.9
= 33.68
D

= 5 x 1.35 x 33.68 x 2 x 0.34² (bar)

101.6
= 0.52 bar = 5.2 m
Hs = hs – hfs +ps = 2.7 – 5.2 + 0 m = – 2.5 m.
Total head H = Ht – Hs = 374 – (–2.5) = 376.5 m » 377 m (37.7 bar)
In this example the total head required is in excess of the 20 bar

maximum working pressure of the pump. To reduce this head so as a
pump can be suitably sized, consideration could be given to any or a
combination of the following parameters:
1. Reduce capacity.
2. Increase tube diameter.
3. Increase pumping temperature to reduce viscosity.
4. Consider two or more pumps in series.

Pump Sizing
Assuming the capacity is a definite requirement and the pumping

temperature cannot be increased the customer should be advised to
increase the discharge tube diameter i.e. from 76 mm to 101.6 mm.
The total head calculations are reworked, and for this particular
example the fluid velocity (V) and friction factor (fD) have already been
established for 101.6 mm diameter tube. Also note, by referring to
the equivalent tube length table 14.7.1 the values for bends 45 deg.
and butterfly valves remain unchanged.
Using the Miller equation to determine friction loss as follows:
D

= 5 x 1.35 x 33.68 x 41 x 0.34² (bar)

101.6
= 10.6 bar = 106 m
Now Ht = ht + hft +pt = 27 + 106 + 0 m = 133 m (13.3 bar).
Now Total head H = Ht – Hs = 133 – (–2.5)

= 135.5 m » 136 m (13.6 bar)
NPSHa


hs = 2.7 m.
hfs = calculated to be 5.2 m.
Pvp= at temperature of 65 oC this is taken as being

Pump Sizing
NPSHa = Pa + hs – hfs – Pvp = 10 + 2.7 – 5.2 – 0 m = 7.5 m.
Due to the high viscosity it is not practical to use pump performance

curves for sizing purposes. The actual pump sizing can be made
using a pump selection program. An approximate guide to pump
sizing can be made by calculation using volumetric efficiency.
For this particular example a pump sized from the pump selection
program using stainless steel tri-lobe rotors with 130°C rotor
clearances would be as follows:
Pump model - SRU5/168/LD.

Connection size - 100 mm (enlarged port).
NPSHr - 2.1 m.
Cavitation check:
NPSHa should be greater than NPSHr i.e. 7.5 m > 2.1 m.

The viscosity of 25000 cP at speed 100 rev/min is well within the
pump’s maximum rated figures.
Power calculation:
10000
From example
• At speed 100 rev/min and total head 13.6 bar, the power at
1 cSt is 4.1 kW,
• at viscosity 25000 cP (18519 cSt) the Pv factor is 110.

10000
= 110 x 100 + 4.1

10000
= 5.2 kW

Pump Sizing
and for a fixed speed drive the appropriate motor power must be
selected, which in this instance would be 5.5 kW being the nearest
motor output power above the required power.
experience and guidelines would be a packed gland arrangement with
polyamide gland packing on hard coated shaft sleeves with EPDM
elastomers. Alternative shaft sealing could be a flushed packed gland
or double flushed mechnical seal.
Alternative Pump Sizing Guide Using Volumetric Efficiency

Calculation.
Referring to the initial suction line sizing curve shown in 14.9, for the
flow rate required of 10 m3/h with viscosity 25000 cP (18519 cSt), a
pump having a 100 mm dia. inlet port would be selected.
For this example a Model SRU5/168 pump will be selected having

100 mm dia. enlarged ports. If a sanitary port is a definite requirement
the Model SRU6/260 pump would be selected.
To calculate pump speed for the SRU5/168 pump selected the

following formula is used as a general guide with volumetric efficiency
of 99% (see 7.2.4).
Pump speed (rev/min) n = Q x 100

q x hv x 60
where: Q = capacity (m3/h)

q = pump displacement (m3/100 rev)
= 10 x 100
0.168 x 0.99 x 60
= 100 rev/min

Pump Sizing
7.8 Worked Examples of Rotary Lobe

Pump Sizing (US units)
The following examples show two different rotary lobe pumps to be
sized for a typical sugar process.
Pump 1 is a low viscosity example handling sugar syrup.

Pump 2 is a high viscosity example handling massecuite.
As described in 7.1 in order to correctly size any type of pump,

information is required such as Product/Fluid data, Performance data
and Site Services data.
Pump 1 – Thin Sugar Syrup pump
Fig. 7.8a Pump 1 - example

15 psi
3 ft
Feed tank
26 ft
3 ft 20 ft
3 ft 6 ft
3 ft 10 ft

the customer. Fluid to be pumped - Sugar syrup.
Viscosity - 62 cSt.
SG - 1.29.
CIP temperature - 203°F.
Performance data:
Discharge - via 33 ft of 2 in dia. tube, plus 1 bend 90
deg. and 1 butterfly valve.
Static head in vessel = 26 ft.
Pressure in vessel = 15 psi.
Suction - via 9 ft of 2 in dia. tube, plus 2 bends 90
deg. and 1 non-return valve.
Static head in tank = 6 ft.
Site Services data:


Pump Sizing

Total head
Therefore ht = 26 ft x (SG = 1.29) = 33.5 ft.

Fig. 7.8b in bends and valves Dp (calculated below).
pt = 15 psi = 35 ft.
Flow Characteristic
Reynolds number Re = 3162 x Q
Dxn
where D = tube diameter (in).

Q = capacity (US gall/min).
n = kinematic viscosity (cSt).
= 3162 x 40
2 x 62
= 1020

Pump Sizing

is 1.0 (see 2.2.2).
Straight tube length = 10 + 20 + 3 = 33 ft

1 bend 90 deg. = 1 x 3 x 1.0 (corr. factor) = 3 ft
1 butterfly valve = 1 x 3 x 1.0 (corr. factor) = 3 ft
Total equivalent length = 39 ft

Re
= 64
1020
= 0.063
Pf = 0.0823 x SG x fD x L x V² (psi)
D

Velocity V = Q x 0.409 where Q = capacity (US gall/min)

D2 D = tube diameter (in)
= 40 x 0.409
22
= 4.1 ft/s
Pf = 0.0823 x 1.29 x 0.063 x 39 x 4.1² (psi)

2
= 2.2 psi = 5 ft
Ht = ht +hft +pt = 33.5 + 5 + 35 ft = 73.5 ft » 74 ft (32 psi).

Pump Sizing

Therefore hs = 6 ft x (SG = 1.29) = 7.7 ft.

ps = 0 (open tank).

is 1.0 (see 2.2.2).
Straight tube length =3+3+3 = 9 ft

2 bend 90 deg. = 2 x 3 x 1 (corr. factor) = 6 ft
1 non-return valve = 1 x 39 x 1 (corr. factor) = 39 ft

Re
= 64
1020
= 0.063
D


= 40 x 0.409
22
= 4.1 ft/s

Pump Sizing
Pf = 0.0823 x 1.29 x 0.063 x 54 x 4.1² (psi)

2
= 3 psi = 7 ft
Hs = hs – hfs +ps = 7.7 – 7 + 0 ft = 0.7 ft (0.3 psi).
Total head H = Ht – Hs =74 – 0.7 = 73.3 ft » 73 ft (32 psi).
NPSHa

hs = 7.7 ft.
NPSHa = Pa + hs – hfs – Pvp = 33.9 + 7.7 – 7 – 0 ft = 34.6 ft.

a pump selection program. The performance curve selection
procedure is more specifically described in 7.6.3.
1.5 in inlet connection would be required. Although the smallest pump
models SR1/008 (with enlarged port), SRU2/013 (with enlarged port)
and SRU2/018 (with sanitary port) have 1.5 in pump inlet
connections, the flow rate required would exceed the pumps speed
limit on the performance curve. We have therefore selected a
performance curve for the pump model SRU3/027/LS with 266°F
rotor clearances due to the CIP requirement, being the next
appropriate pump size. Pump sized as follows:
Pump model - SRU3/027/LS.

Connection size - 1.5 in.
NPSHr - 11.9 ft.
Cavitation check:
NPSHa should be greater than NPSHr i.e. 34.6 ft > 11.9 ft.

Pump Sizing

The viscosity of 62 cSt at speed 613 rev/min is well within the
pumps maximum rated figures.
Power calculation:
10000
From example
At speed 613 rev/min and total head 32 psi, the power at
1 cSt is 1.2 hp,
At viscosity 62 cSt the Pv factor is 3.

10000
= 3 x 613 + 1.2
10000
= 1.4 hp
and the appropriate motor power must be selected, which in this
instance would be 2 hp being the nearest motor output power above
the required power.
The recommended type of shaft seal based upon Alfa Laval

application experience and guidelines would be a single flushed
mechanical seal with tungsten carbide/tungsten carbide faces and
EPDM elastomers.
Hard tungsten carbide seal faces due to the abrasive nature of

sugar syrup.
Flushed version to prevent the sugar syrup from crystallising
within the seal area.
EPDM elastomers for compatibility of both sugar syrup and CIP
media.

Pump Sizing
Pump 2 – Massecuite pump
Fig. 7.8c Pump 2 - example
65 ft
6 ft 130 ft
3 ft

the customer. Fluid to be pumped - Massecuite.
Viscosity - 18519 cSt.
SG - 1.35
Performance data:
Discharge - via 130 ft of 3 in dia. tube, plus 2 bends
Suction - via 3 ft of 4 in dia. tube, plus 1 bend
90 deg. and 1 butterfly valve.
Site Services data:



Pump Sizing
Total head
Therefore ht = 65 ft x (SG = 1.35) = 88 ft.

Fig. 7.8d in bends and valves Dp (calculated below).
pt = 0 psi (open tank) = 0 ft.
Flow Characteristic
Dxn

n = kinematic visosity (cSt).
= 3162 x 44
3 x 18519
= 2.5

Pump Sizing

is 0.25 (see 2.2.2).
Straight tube length = 130 ft

2 bend 45 deg. = 2 x 3 x 0.25 (corr. factor) = 1.5 ft
1 butterfly valve = 1 x 7 x 0.25 (corr. factor) = 1.75 ft

Re
= 64
2.5
= 25.6
Pf = 5 x SG x fD x L x V² (psi)
D


= 40 x 0.409
32
= 2 ft/s
Pf = 0.0823 x 1.35 x 25.6 x 133 x 2² (psi)

3
= 504 psi = 1163 ft

Pump Sizing

Therefore hs = 6 ft x (SG = 1.35) = 8 ft.

ps = 0 (open tank).
To ascertain hfs the flow characteristic and equivalent line length must
Flow Characteristic
Dxn

n = kinematic visosity (cSt).
= 3162 x 44
4 x 18519
= 1.9

is 0.25 (see 2.2.2).
Straight tube length = 3 ft

1 bend 90 deg. = 1 x 7 x 0.25 (corr. factor) = 1.75 ft
1 butterfly valve = 1 x 7 x 0.25 (corr. factor) = 1.75 ft
Total equivalent length = 6.5 ft

Re
= 64
1.9
= 33.68

Pump Sizing
D


= 44 x 0.409
42
= 1.1 ft/s
Pf = 0.0823 x 1.35 x 33.68 x 6.5 x 1.1² (psi)

4
= 7.4 psi = 17 ft
Hs = hs – hfs +ps = 8 – 17 + 0 ft = –9 ft.
Total head H = Ht – Hs = 1251 – (–9) = 1260 ft (546 psi)
In this example the total head required is in excess of the 290 psi
maximum working pressure of the pump. To reduce this head so as a
pump can be suitably sized, consideration could be given to any or a
combination of the following parameters:
1. Reduce capacity.
2. Increase tube diameter.
3. Increase pumping temperature to reduce viscosity.
4. Consider two or more pumps in series.
Assuming the capacity is a definite requirement and the pumping

temperature cannot be increased the customer should be advised to
increase the discharge tube diameter i.e. from 3 in to 4 in.

Pump Sizing
The total head calculations are reworked, and for this particular
example the fluid velocity (V) and friction factor (fD) have already been
established for 4 in diameter tube. Also note, by referring to the
equivalent tube length table 14.7.2 the values for bends 45 deg. and
butterfly valves remain unchanged.
Using the Miller equation to determine friction loss as follows:
D

= 0.0823 x 1.35 x 33.68 x 133 x 1.1² (psi)

4
= 150 psi = 346 ft
Now Ht = ht + hft +pt = 88 + 346 + 0 ft = 434 ft (188 psi).
Now Total head H = Ht – Hs = 434 – (–9) = 443 ft (192 psi).
NPSHa
NPSHa = Pa + hs – hfs – Pvp .

hs = 8 ft.
NPSHa = Pa + hs – hfs – Pvp = 33.9 + 8 – 17 – 0 m = 24.9 ft.

Pump Sizing
Due to the high viscosity it is not practical to use pump performance

curves for sizing purposes. The actual pump sizing can be made using
a pump selection program. An approximate guide to pump sizing can
be made by calculation using volumetric efficiency.
For this particular example a pump sized from the pump selection
program using stainless steel tri-lobe rotors with 266° F rotor
clearances would be as follows:
Pump model - SRU5/168/LD.

Connection size - 4 in (enlarged port).
NPSHr - 6.9 ft.
Cavitation check:
NPSHa should be greater than NPSHr i.e. 24.9 ft > 6.9 ft.

The viscosity of 18519 cSt at speed 100 rev/min is well within the
pumps maximum rated figures.
Power calculation:
Total Required Power (hp) =
Pv x Pump speed (rev/min) + Power at 1 cSt (hp)
10000
From example
• At speed 100 rev/min and total head 192 psi, the power at
1 cSt is 5.5 hp,
• At viscosity 18519 cSt the Pv factor is 110.
Total Required Power (hp) =

Pv x Pump speed (rev/min) + Power at 1 cSt (hp)
10000
= 110 x 100 + 5.5

10000
= 6.6 hp
and for a fixed speed drive the appropriate motor power must be
selected, which in this instance would be 7.5 hp being the nearest
motor output power above the required power.

Pump Sizing
experience and guidelines would be a packed gland arrangement with
polyamide gland packing on hard coated shaft sleeves with EPDM
elastomers. Alternative shaft sealing could be a flushed packed gland
or double flushed mechnical seal.
Alternative Pump Sizing Guide Using Volumetric Efficiency

Calculation.
Referring to the initial suction line sizing curve shown in 14.9, for the
flow rate required of 44 US gall/min with viscosity 18519 cSt, a
pump having a 4 in dia. inlet port would be selected.
For this example a Model SRU5/168 pump will be selected having 4

in dia. enlarged ports. If a sanitary port is a definite requierement the
Model SRU6/260 would be selected.
To calculate pump speed for the SRU5/168 pump selected the

following formula is used as a general guide with volumetric efficiency
of 99% (see 7.2.4).
Pump speed (rev/min) n = Q x 100

q x hv
where: Q = capacity (US gall/min)

= 44 x 100
44.39 x 0.99
= 100 rev/min

Pump Specification Options
8. Pump Specification Options

This section gives detailed descriptions of the various specification options
available for the Alfa Laval pump ranges, such as port connections,
heating/cooling jackets, pressure relief valves and other ancillaries.
8.1 Centrifugal and Liquid Ring Pumps

8.1.1 Port Connections
Pumps are supplied with screwed male connections of all major
standards, i.e.: SMS, DIN, ISO, BS, DS, GC-clamp, bevel seat, DC
and H-line.
Pump Range Pump Model Nominal Connection Size

Inlet Outlet Inlet Outlet
mm mm in in
LKH LKH-5 50 40 2 1.5

LKH-10 65 50 2.5 2
LKH-15 100 80 4 3
LKH-20 65 50 2.5 2
LKH-25 80 65 3 2.5
LKH-35 65 50 2.5 2
LKH-40 80 65 3 2.5
LKH-45 100 80 4 3
LKH-50 100 80 4 3
LKH-60 100 100 4 4
LKH-70 100 80 4 3
LKH-80 150 100 6 4
LKH-Multistage LKH-112 50 40 2 1.5
LKH-113 50 40 2 1.5
LKH-114 50 40 2 1.5
LKH-122 80 65 3 2.5
LKH-123 80 65 3 2.5
LKH-124 80 65 3 2.5
LKHP LKHP-10 65 50 2.5 2
LKHP-15 100 80 4 3
LKHP-20 65 50 2.5 2
LKHP-25 80 65 3 2.5
LKHP-35 65 50 2.5 2
LKHP-40 80 65 3 2.5
LKHP-45 100 80 4 3
LKHP-50 100 80 4 3
LKHP-60 100 100 4 4


Inlet Outlet Inlet Outlet
mm mm in in
LKHSP LKHSP-10 65 50 2.5 2

LKHSP-20 65 50 2.5 2
LKHSP-25 80 65 3 2.5
LKHSP-35 65 50 2.5 2
LKHSP-40 80 65 3 2.5
LKHI LKHI-10 65 50 2.5 2
LKHI-15 100 80 4 3
LKHI-20 65 50 2.5 2
LKHI-25 80 65 3 2.5
LKHI-35 65 50 2.5 2
LKHI-40 80 65 3 2.5
LKHI-45 100 80 4 3
LKHI-50 100 80 4 3
LKHI-60 100 100 4 4
LKH-UltraPure LKH-10 65 50 2.5 2
LKH-20 65 50 2.5 2
LKH-25 80 65 3 2.5
LKH-35 65 50 2.5 2
LKH-40 80 50 3 2
MR MR-166S 50 50 2 2
MR-185S 80 80 3 3
MR-200S 80 80 3 3
MR-300 80 80 3 3
Table 8.1.1a
8.1.2 Heating/Cooling Jackets

In some applications heating of the fluid being pumped may be
required to reduce the fluid viscosity so that satisfactory operation is
Jacket achieved. Alternatively it may be necessary to cool the fluid being
Pump casing
pumped where heat is generated by means of the fluid repeatedly
being passed through the pump. On such occasions some pump
models can be fitted with heating/cooling jackets.
Fig. 8.1.2a Heating/Cooling jacket

8.1.3 Pump Casing with Drain

In some applications it is a requirement that no fluid should be left in
the pump casing. This can be achieved by either:
- Fitting a drain connection to
- Turning the pump outlet downwards the bottom of the pump casing
or
Pump casing
Drain
Fig. 8.1.3a Turned pump casing Fig. 8.1.3b Pump casing with drain
Gap: 2 mm 8.1.4 Increased Impeller Gap

Back plate In some applications, e.g. when using a LKH centrifugal pump as a
booster pump in a cream pasteurisation unit, there is a risk that a
Impeller
hard layer of proteins will slowly build up between the backside of the
impeller and the back plate. This will activate the thermal relay of the
motor after a few hours of operation so that the pump stops.
The operating time of the pump can be increased by increasing the

Fig. 8.1.4a Increased gap standard gap width between the back of the impeller and the back
plate, from 0.5 mm to 2.5 mm. The gap is achieved by machining the
back of the impeller. This increased gap reduces the head by approx.
5%.
For this type of application it is recommended to select a motor size

with an output power one step higher than the standard selection so
as to avoid the motor thermal relay being constantly activated.
8.1.5 Pump Inlet Inducer

Inducer In some applications it may be necessary to improve the suction
conditions by means of fitting the pump inlet with an inducer. This has
the effect of improving NPSH requirements for difficult applications
and/or assisting the flow of a viscous fluid into the pump casing.
Impeller Inlet
Fig. 8.1.5a Inducer in pump inlet


8.2.1 Rotor Form
Table 8.2.1a
Rotor Form Material Pump Range
SRU SX
Tri-lobe Stainless steel ü

Tri-lobe Rubber covered ü
Bi-lobe Stainless steel ü
Bi-lobe Non galling alloy ü
Multi-lobe Stainless steel ü
Fig. 8.2.1a Bi-lobe Fig. 8.2.1b Tri-lobe Fig. 8.2.1c Multi-lobe
Tri-lobe Rotors (Stainless steel)

Most duties can be accomplished by pumps fitted with stainless steel
tri-lobe rotors. The tri-lobe rotor with its mathematically correct
profile and precision manufacture ensure interchangeability as well as
smooth, high performance pumping action.
These are available on the SRU pump range with 3 temperature

ratings:
• up to 70°C (158oF).
• up to 130°C (266oF).
• up to 200°C (392oF).
and pressures up to 20 bar (290 psig).

Bi-lobe Rotors (Stainless steel)

Large fluid
chamber
These are generally used for handling delicate suspended solids
Bilobe rotors
where minimum product damage is required. Typical applications are
jam containing fruit pieces, sausage meat filling, petfood, soups and
sauces containing solid matter.
Gentle
pumping
action
ratings:
Fig. 8.2.1d Bi-lobe rotors for solids • up to 70°C (158oF).
handling • up to 130°C (266oF).
• up to 200°C (392oF).
Bi-lobe Rotors (Non galling alloy)

Manufactured from non-galling alloy these rotors have an advantage
over stainless steel, as smaller clearances (see 8.2.2) can be used,
leading to increased efficiencies.

ratings:
• up to 70°C (158oF).
• up to 130°C (266oF).
• up to 200°C (392oF).
Tri-lobe Rubber Covered Rotors

This rotor has a stainless steel insert covered in NBR rubber, and due
to the resilience of the rubber coating these rotors have a slight
interference fit with the pump rotorcase when initially fitted. This
results in improved pump performance and suction lift capability over
stainless steel tri-lobe rotors.
Rotors are suitable for continuous operation up to 70°C (158oF) and

intermittent operation up to 100°C (212oF), and pressures up to 7
bar (100 psig).
Multi-lobe Rotors
This rotor is manufactured from stainless steel and as the name
suggests has many lobes. For the SX pump range these rotors have
4 lobes and are designed to maximise efficiency, reduce shear and
provide a smooth pumping action. Rotors are suitable for
temperatures up to 150°C (302oF) and pressures up to 15 bar (215
psig).

Clearances are necessary to 8.2.2 Clearances

avoid rotor to rotor, rotor to Within the pump head are clearances, which are the spaces between
rotorcase and rotor to rotating components and between rotating and stationary
rotorcase cover contact. The components. The key clearances are as follows:
size of these clearances is
related to the pressure and • Radial clearance (between rotor tip and rotorcase).
temperature of pump • Mesh clearance (between rotors).
operation and rotor material. • Front clearance (between front of rotor and rotorcase cover).
• Back clearance (between back of rotor and back face of rotorcase).
Fig. 8.2.2a Clearances
Radial
Back
Mesh
Front
Pressure effect
The design concept of the rotary lobe pump is to have no contacting
parts in the pumphead. This requires having the shaft support
bearings to be mounted outside of the pumphead, which results in an
overhung load, caused by the rotors fitted to the shafts (see Fig.
8.2.2b). The effect of pressure on the rotors will cause shaft
deflection, which could result in contact between rotors, rotorcase
and rotorcase cover. As product wetted parts of the SRU and SX
pump ranges are predominantly manufactured from stainless steel,
any contact between rotating and stationary parts would cause
‘galling’ and possible pump seizure. To allow for this pressure effect,
clearances are built into the pumphead between surfaces that may
contact. For the SRU and SX pump ranges there is only one pressure
rating, which is the maximum differential pressure of the particular
pump model. The pressure effect is less significant on pumps fitted
with rubber covered or non-galling alloy rotors.

Fig. 8.2.2b Pressure effect

Force due to pressure
Support bearings
Shaft
Rotor
Overhang length
Outlet
Inlet
Temperature effect
Temperature change can be caused by the fluid being pumped, pump
Rotorcase mechanism, drive unit and/or the environment. Any CIP operation
Rotor required should also be taken into consideration (see section 10 for
detailed explanation of CIP). Changes in temperature will cause
Shaft expansion upon heating or contraction upon cooling, to the rotorcase
and gearcase components. The most significant result is movement
Standard between shaft and gearcase/rotorcase causing the rotors to move
clearance forward/backward in the rotorcase, thereby reducing the front
Standard
rotor width clearance. To compensate for this, the SRU pump range has
increased clearances as shown below. SRU pumps are designed for
various temperature ratings for rotors i.e. 70°C (158°F), 130°C
(266°F) or 200°C (392°F). On the SX pump range the design of the
mechanical seal eliminates contact between the fluid being pumped
and the shaft. This results in the shaft not being subjected to the full
temperature variation and therefore only one temperature rating of
150°C (302°F) is necessary.
Thermal
expansion
Increased
clearance Decreased
rotor width
The clearance is exaggerated to show

the temperature effect
Fig. 8.2.2c Increased clearance

8.2.3 Port Connections

Pumps are supplied with screwed male connections to all major
standards as follows:
Table 8.2.3a
Standard Screwed Pump Range
Connection Type SRU SX
3A/Acme ü
BSP ü
BSPT ü
DIN11851/405 ü ü
ISS/IDF ü ü
NPT ü
RDG ü
RJT ü ü
SMS ü ü
Tri-Clamp (BS4825) ü ü
All models in the SRU and SX pump ranges are supplied with full bore
through porting, conforming to International Sanitary Standards
BS4825 / ISO2037. This provides effective CIP cleaning and
maximises inlet and outlet port efficiency and NPSHr characteristics.
The option of the enlarged port on the SRU pump range can be
chosen for high viscosity applications.
Fig. 8.2.3a Sanitary port design Fig. 8.2.3b Enlarged port design
The SRU pump range when having enlarged ports can also be
supplied with flanged connections of all major standards i.e.
ASA/ANSI125, ASA/ANSI150, ASA/ANSI300, BS10 table E,
BS10 table F, BS4504/DIN2533 and JIS10K.
Flanges for vertically ported pumps are not fitted directly to the
discharge port. In this instance an elbow bend is included to which the
flange is fitted.


Sanitary Enlarged
mm in mm in
SRU SRU1/005 25 1 - -
SRU1/008 25 1 40 1.5
SRU2/013 25 1 40 1.5
SRU2/018 40 1.5 50 2
SRU3/027 40 1.5 50 2
SRU3/038 50 2 65 2.5
SRU4/055 50 2 65 2.5
SRU4/079 65 2.5 80 3
SRU5/116 65 2.5 80 3
SRU5/168 80 3 100 4
SRU6/260 100 4 100 4
SRU6/353 100 4 150 6
SX SX1/005 25 1
SX1/007 40 1.5
SX2/013 40 1.5
SX2/018 50 2
SX3/027 50 2
SX3/035 65 2.5
SX4/046 50 2
SX4/063 65 2.5
SX5/082 65 2.5 For size 150 mm (6 in)
SX5/115 80 3 screwed male connections,
SX6/140 80 3
these are only available as
SX6/190 100 4
SX7/250 100 4 DIN11851/405, SRJT or
SX7/380 150 6 Tri-Clamp (BS4825).
Table 8.2.3b
8.2.4 Rectangular Inlets

For handling extremely viscous products and/or large solids that
Hopper Rectangular would naturally bridge a smaller port, SRU rotary lobe pumps can be
inlet
supplied with a rectangular inlet. Usually the pump will be in vertical
port orientation to allow the product to flow into the pumping
chamber under gravity from a hopper mounted directly above or
Outlet mounted with an adaptor to facilitate connection to large diameter
pipework.
Fig. 8.2.4a Rectangular inlets
As can be seen from the table below there is a significant percentage
area increase when using a rectangular inlet compared to a sanitary
port connection. This increases the pumps ability to handle highly
viscous products.

Table 8.2.4a
Pump Model Sanitary port Rectangular inlet % area increase
area (mm2) area (mm2) above sanitary
port diameter
SRU1/005 387 660 171

SRU1/008 387 1260 326
SRU2/013 387 1216 314
SRU2/018 957 1976 206
SRU3/027 957 2112 221
SRU3/038 1780 3360 189
SRU4/055 1780 2688 151
SRU4/079 2856 4320 151
SRU5/116 2856 5032 176
SRU5/168 4185 8160 195
SRU6/260 7482 13888 186
SRU6/353 7482 18240 244
Connections Saddle 8.2.5 Heating/Cooling Jackets and Saddles

for steam, Rotary Lobe pumps can be fitted with jackets to the rotorcase cover
hot/cold fluid and saddles to the rotorcase. These are primarily used for warming
the pumphead so as to prevent the fluid pumped being cooled and
become viscous or allowed to solidify/crystallise. These can also be
used for cooling purposes.
Jacket
The maximum pressure and temperature of heating/cooling fluid is
Fig. 8.2.5a Heating/Cooling jackets and 3.5 bar (50 psig) and 150°C (302oF) respectively. Heating/cooling
saddles jackets and saddles should be in operation approximately 15 minutes
prior to pump start up and remain in operation 15 minutes after pump
shut down.
Typical applications include:

• Adhesive • Chocolate • Gelatine • Jam • Resin
Jackets are available on both the SRU and SX pump ranges, but
saddles are only available on the SRU pump range.

8.2.6 Pump Overload Protection

Due to the positive action of the rotary lobe pump any restriction on
the outlet side of the pump, either partial or total, will result in
excessive pressure developing in the pumphead. It is therefore
essential that some form of overload protection be installed to
protect pump, drive unit and also limit pressure build up within
associated process equipment. This protection will normally take the
form of an external spring-loaded pressure relief valve fitted to the
outlet side of the pump which will open under high pressure and allow
fluid to return to the inlet side of the pump via a by-pass loop. Other
alternatives are to fit the pump with an integral relief valve as
described below, or use of proprietary electronic devices.
Pressure Relief Valves

Pressure These can be supplied as an integral part of the pump and do not
relief valve require external pipework. The assembly replaces the standard
rotorcase cover and is intended to protect the pump from over
pressurisation. It is suitable for bi-direction pump operation and can
be retrofitted. The valve will provide full pump protection for fluids
having viscosities below 500 cP, above this figure Alfa Laval should
be consulted with regard to specific flow rates in relation to viscosity
Fig. 8.2.6a Pressure relief valve and differential pressures. The design is such that the valve
mechanism is isolated from the pumped fluid.
Valve open Valve closed
Rotors Large slip path across

Rotor nuts rotorcase cover
Small slip path across

rotorcase cover
Relief valve piston moves

Relief valve piston
back against the springs
Fig. 8.2.6b Relief valve operation

As it is a mechanical device the relief valve does not operate

instantaneously due to mechanical response time. The valve will begin
to relieve at a pressure less than the fully open pressure. This
‘accumulation’ will vary depending upon the duty pressure, viscosity
and pump speed. The accumulation tends to increase as pressure or
pump speed decrease, and as viscosity increases. The valve is set to
relieve at the required pressure by the correct choice of springs and
can be adjusted on site to suit actual duty requirements.
The relief valve can be provided with the following options:
Automatic with Pneumatic Override

These valves may be pneumatically overridden for CIP conditions and
they may be remotely controlled if required. Air supply should be
clean and dry at pressures of 4 bar (60 psig) minimum and 8 bar (115
psig) maximum.
Automatic with Manual Override

This valve has a lever to enable manual override for CIP or certain
tank filling applications.
Valve Type Pump Range - Availability Normal Operating Pressure Range

bar psig
Standard SRU1-6 7-19 100-275

Pneumatic override SRU1-6 7-19 100-275
Manual override SRU1-3 19 275
SRU4-5 7-10 100-145
SRU6 7 100
Table 8.2.6a
Pressure relief valves are only available for the SRU range pumps
fitted with metal rotors.
Pump Protection Unit (PPU)

The Pump Protection Unit is a non-intrusive alternative to mechanical
relief valves, conventional electronic shear pin or mechanical over-load
protection devices. It is designed to protect Alfa Laval rotary lobe
pumps and incorporates micro-controller technology. The PPU is not
a power meter or data-logging device but has the ability to monitor
true consumption through continuous power monitoring. The PPU is
not a pre-set device and requires a simple set-up procedure to be
Fig. 8.2.6c Pump protection unit carried out to suit specific duty conditions of the pump to be
monitored. After initial setting is completed the monitoring process is
automatic and the pump is under the protection of the PPU.

The PPU will detect over-load and rapidly increasing load. One
example of an over-load condition could result from a gradual
increase in viscosity of the pumped media. This condition would in
turn result in a higher discharge pressure, therefore increased power
consumption. Another example could result from a partially closed
valve in the discharge pipe also giving rise to excess pressure and
therefore power consumption. As well as responding to system
related transients, the PPU will also respond to mechanical changes
such as bearing or lubrication failure, both of which could result in
pump seizure if not detected and corrected.
The PPU will detect a rapidly increasing load such as that caused by a
solid object entering the pump and becoming trapped between the
rotors. The resulting rapid power increase from this type of event,
even within the lines of the over-load trip threshold, will cause an
automatic shutdown if desired thereby limiting the degree of damage.
The PPU will detect under-load since this highlights a condition

preventing optimum pump operating efficiency. One example of
under-load could result from a blocked or closed valve in the inlet
pipe, a burst inlet or outlet pipe, or even an empty supply vessel.
8.2.7 Ancillaries
Rotary Lobe pumps can be supplied bare shaft (without drive) or
mounted on a baseplate with drive such as electric motor, air motor,
and diesel or petrol engine dependent upon customer requirements
and services available. Electric motors being the most commonly
used method of drive, are described in more detail in section 9.
Fig. 8.2.7a Typical motorised rotary lobe

pump unit
Fixed Speed
Rotary Lobe pumps generally operate at low to medium speeds i.e.
25 to 650 rev/min, and therefore some form of speed reduction is
required from normal AC motor synchronous speeds of 1500, 1000
and 750 rev/min for 50 Hz (1800, 1200 and 900 rev/min for 60 Hz).
This is generally achieved by using a geared electric motor direct
coupled to the pump drive shaft via flexible coupling. An alternative
arrangement would be an electric motor with a wedge belt pulley
drive reducing the motor speed to the pump output speed required.

When exact flow is not critical a fixed speed drive is generally used.
The integral geared electric motor is the most commonly used type
of fixed speed drive. This is a compact low cost unit, which is easy to
install, as it only requires one coupling and a safety guard.
Complete ranges of drive speeds are available from the different

manufacturers and usually one can be found within a few rev/min of
the required speed.
Some pumps operate continuously for 24 hours per day and others
operate intermittently. How a pump operates will determine the
choice of geared electric motor. Motor manufacturers give
recommendations for their motors relating to the number of hours
per day of operation and the frequency of starting and stopping.
Variable Speed
To handle changing duty conditions or a number of different duties, it
may be necessary to use a variable speed drive or frequency
converter to obtain correct pump duty speeds. There are many types
of mechanical and hydraulic variable speed drives available in a wide
range of speeds, which are well suited to rotary lobe pump
characteristics by offering the ability to adjust the pump speed to
control flow and adjust for system conditions. The frequency
converter allows the operator to change the frequency of the electric
motor, thereby changing pump speed and controlling flow (see 9.10).
Other Drive Types

Air motors, although not commonly used as pump drives, can
provide good low cost drive in certain applications. In addition diesel
or petrol engines can be used as pump drivers.
Baseplates
The Alfa Laval ‘standard’ is a pressed mild steel or stainless steel
design which is required to be bolted to the floor (see 12.3). The Alfa
Laval mild steel baseplate is supplied painted to suit customer
requirements and the stainless steel has a dull polish finish. An
alternative is to mount the pump and drive unit on a portable trolley
design baseplate complete with control gear and trailing lead as
required.
In some application areas such as dairy or brewing it is normal

practice to hose down pump units and floorings – in these
circumstances ball feet can be fitted to baseplates, which can be a
fixed or variable height, to raise baseplate above floor level.
Baseplates can also be designed to meet specific customer
standards when required.

Guards
All rotating machinery should be adequately guarded and when
pumps are supplied complete with a drive, a guard is fitted over the
transmission (flexible coupling or wedge belt) which links the pump
drive shaft to the output shaft of the selected driver.
The selection of guard material is important relative to its working

environment. Non-sparking materials such as aluminium or brass are
used with flameproof/explosion proof motors in hazardous areas. For
non-hazardous applications mild steel or stainless steel is generally
used.


Motors
9. Motors
This section describes electric motors, including information on
motor protection, methods of starting, motors for hazardous
environments and speed control.
The electric motor is the most commonly used method of pump

drive, due to the following:
• Electrical power supply is usually readily available and easy to

install.
• High efficiency due to low losses when transforming from
electrical to mechanical power.
• The electric motor can absorb variations in the torque
requirement of a pump, i.e. as a result of changes in product/
duty conditions, inertia in the bearings, frequent starts etc.
• Easy speed control.
All Alfa Laval pump ranges can be fitted with AC type Totally Enclosed
Fan Ventilated (TEFV) squirrel cage three phase electric motors
complying with various international standards and regulations such
as IEC, CENELEC, VDE, DIN and BS. Electric motors supplied in the
USA are generally to NEMA standard. Single phase electric motors
can also be fitted to Alfa Laval rotary lobe pumps.
Fig. 9a Electrical hazard

Motors
The standard design of an AC motor includes the following main

parts:
Item Description
1. Stator housing.
2. Ball bearings.
3. Bearing housing.
4. Fan.
5. Fan cap.
6. Housing for electrical connection.
7. Iron core.
8. Three phase windings.
9. Rotor.
10. Motor shaft.
Fig. 9b Exploded view of a typical AC

motor
The motor is constructed as follows:
• The stator is fixed in the stator housing (1).

• The ball bearings (2) are fixed in the bearing housing (3), which
close the stator housing.
• The ball bearings carry the rotor (9) and the motor shaft (10).
• The fan (4), which cools the motor, is fixed to the motor shaft.
• The fan is protected by means of the fan cap (5).
• The housing for electrical connection (6) is situated on the
stator housing.
• There is an iron core (7) in the stator housing. The iron core
consists of thin iron sheets with a thickness of 0.3 - 0.5 mm.
• The three phase windings (8) are situated in the grooves of the
iron core.
The three phase windings and the stator core are designed to
produce a magnetic field in pairs of poles. When the stator is
connected to a three-phase supply voltage the magnetic fields of the
individual phase windings form a symmetrically rotating magnetic field
which is called the rotational field. The speed of the rotational field is
called the synchronous speed.

Motors
9.1 Output Power

The output power is always lower than the rated electrical power due
to various losses in the motor. The ratio of output power to rated
electrical power is known as the motor efficiency. The table below
shows output power that is specified in standard ratings.
Frequency Output Power in kW
50 Hz 0.37 0.55 0.75 1.1 1.5 2.2 3 4 5.5 7.5

60 Hz 0.43 0.63 0.86 1.27 1.75 2.5 3.5 4.6 6.3 8.6
50 Hz 11 15 18.5 22 30 37 45 55 75 90
60 Hz 12.7 17.5 21 25 35 42 52 64 87 105
Table 9.1a
Frequency Output Power in hp
60 Hz 0.5 0.75 1 1.5 2 3 5 7.5 10

15 20 25 30 40 50 60 75 100
Table 9.1b (Nema motors)
9.2 Rated Speed

The rated speed of the motor is always lower than the synchronous
speed due to motor slip.
The connection between synchronous speed, rated speed, frequency

and poles is shown in the table below:
No. Poles 2 4 6 8 12
No. Pairs of poles 1 2 3 4 6
Synchronous speed at 50 Hz - rev/min 3000 1500 1000 750 500
Rated speed at 50 Hz - rev/min 2880 1440 960 720 480
Synchronous speed at 60 Hz - rev/min 3600 1800 1200 900 720
Rated speed at 60 Hz - rev/min 3460 1720 1150 860 690
Table 9.2a

Motors
9.3 Voltage
Standard motors for use on 3 phase 50 or 60 Hz can be wound for
any single voltage as follows:
Up to 3 kW (4 hp) - 230 to 400 volts.

4 kW (5.5 hp) and over - 400 to 690 volts.
Euronorm motors supplied at 400 volts will generally operate

satisfactorily with voltage variations of ± 10% from the rated voltage.
9.4 Cooling
Motor cooling is specified by means of the letters IC (International
Cooling) in accordance with standards. The most common is IC411
(Totally Enclosed Fan Ventilated - TEFV) where an externally mounted
fan cools the motor.
Methods of cooling are shown below:

Code Arrangement
IC411 Totally Enclosed Fan Ventilated (TEFV) – motor cooled by an externally mounted fan
IC410 Totally Enclosed Non Ventilated (TENV) – self cooling, no externally mounted fan
IC418 Totally Enclosed Air Over Motor (TEAOM) – motor cooled by airstream
IC416 Totally Enclosed Forced Cooled (TEFC) – motor cooled by an independent fan
Table 9.4a
9.5 Insulation and Thermal Rating

Standard motors will operate satisfactorily in an ambient temperature
range of - 20°C (-68o F) to + 40°C (104o F) (class B temperature rise)
and at altitudes up to 1000 metres above sea level.
Motors supplied with class F insulation system with only class B

temperature rise (80°C) (176o F) ensure an exceptional margin of
safety and longer life even in abnormal operating conditions such as
withstanding ambient temperatures up to 55°C (131o F) or 10%
overload or adverse supply systems. Motors operating in ambient
temperatures higher than 55°C (131o F) will have class H insulation.
Some derating of the motor may be necessary for high ambient
temperatures and high altitude.

Motors
9.6 Protection
The degree of motor protection is specified by means of the letters IP
(International Protection) in accordance with standards. These state
the method of determining degrees of ingress protection for both
dust and water. The letters IP are followed by two digits, the first of
which specifies the protection against contact and ingress of foreign
bodies and the second digit specifies the protection against water.
Table showing degrees of protection is shown below:
Designation 1st Digit 2nd Digit
Protection against contact and ingress Protection against water

of foreign bodies
IP44 Protection against contact with live or Water splashed against the motor from
moving parts by tools, wires or other any direction shall have no harmful effect.
objects of thickness greater than 1 mm.
Protection against the ingress of solid
foreign bodies with a diameter greater
than 1 mm.
IP54 Complete protection against contact with Water splashed against the motor from
live or moving parts inside the enclosure. any direction shall have no harmful effect.
IP55 Protection against harmful deposits of Water projected by a nozzle against the
dust. The ingress of dust is not totally motor from any direction shall have no
prevented, but dust cannot enter in an harmful effect.
IP56 amount sufficient to interfere with Motor protected against conditions on a
satisfactory operation of the machine. ship’s deck or powerful water jets.
IP65 No ingress of dust. Water projected by a nozzle against the
motor from any direction shall have no
harmful effect.
Table 9.6a
Tropic Proof Treatment

Motors operating in tropical climates are invariably subjected to hot,
humid and wet conditions, which will produce considerable amounts
of condensation on internal surfaces. Condensation occurs when the
surface temperature of the motor is lower than the dew-point
temperature of the ambient air. To overcome this motors can be
supplied with special tropic proof treatment. Failure to include this
treatment and the resulting corrosion can cause irreparable damage
to stator windings and moving parts.
Anti-Condensation Heaters
Where the motor is to be left standing for long periods of time in
damp conditions it is recommended that anti-condensation heaters
are fitted and energised to prevent condensation forming in the motor
enclosure. These heaters are normally 110 volts or 220 volts.

Motors
Thermistors
To protect the motor windings from overload due to high
temperature, motors can be fitted with thermistors, which are
temperature-dependent semi-conductor devices embedded in the
motor windings. Where motors can be allowed to operate at slow
speed, i.e. being used with a frequency converter (see 9.9), it is
normal to fit thermistors to prevent the motor from overloading or to
insufficient cooling from the motor fan.

Motors
9.7 Methods of Starting

There are three starting methods:
1. Direct On Line (D.O.L.).
2. Star/Delta (Y/D).
3. Soft.
Direct On Line Starting

The connection between supply voltage and rated current is very
important with regards to motor starting. The simplest way to start
the motor is to connect directly the mains supply to the motor. In this
case the starting current is high, often 5 to 8 times higher than the
rated current.
Motors fitted to centrifugal and liquid ring pumps are normally directly
started, as the moment of inertia of the motor is low due to pump
design and the fluids being pumped having low viscosities. In this
case the starting time with high starting current is very low and it can
consequently be ignored.
Star/Delta (Y/D) Starting

If pumping viscous fluids the starting time with the high starting
current is longer. It can, therefore, be necessary to restrict the starting
current by means of Y/D - starting of the motor. The current can be
restricted by starting the motor in Y-connection and then changing to
D-connection.
Fig. 9.7a Connection of three-phase

single speed motor
Soft Starting
The soft start provides a smooth start at the same time, as the
starting current is limited. The magnitude of the starting current is
directly dependent on the static torque requirement during a start and
on the mass of the load that is to be accelerated. In many cases the
soft starter saves energy by automatically adapting the motor
voltage continually to the actual requirement. This is particularly
important when the motor runs with a light load.
Soft starting can also be achieved using a frequency converter.

Motors
9.8 Motors for Hazardous Environments

Zones
The degree of hazard varies from extreme too rare. Hazardous areas
are classified into three Zones as follows:
By implication, an area that is Zone 0,

not classified Zone 0, 1 or 2 is in which an explosive gas-air mixture is continuously present or
deemed to be a present for long periods – No motors may be used in this zone.
non-hazardous or safe area.
Zone 1,
in which an explosive gas-air mixture is likely to occur in normal
operation.
Zone 2,
in which an explosive gas-air mixture is not likely to occur in normal
operation and if it occurs it will only be present for a short time.
To ensure equipment can be safely used in hazardous areas, its gas

group must be known and its temperature class must be compared
with the spontaneous ignition temperature of the gas mixtures
concerned.
Table 9.8a
Temperature Ignition temperature Max. permitted temperature
class for gas/vapour of electrical equipment
T1 up to 450oC (842oF) 450oC (842oF)

T2 300 to 450oC (572 to 842oF) 300oC (572oF)
T3 200 to 300oC (410 to 572oF) 200oC (410oF)
T4 135 to 200oC (275 to 410oF) 135oC (275oF)
T5 100 to 135oC (212 to 275oF) 100oC (212oF)
T6 85 to 100oC (185 to 212oF) 85oC (185oF)
Group I Equipment for coal mines susceptible to methane gas.

Group II Equipment for explosive atmospheres other than mines i.e. surface industries.
IIA Group II is subdivided according to the severity of the environment. IIC is the highest rating. A motor from
IIB one of the higher categories can also be used in a lower category.
IIC
Table 9.8b

Motors
Flameproof Enclosure - EEx d and EEx de

These motors are designated for operation in Zone 1 hazardous
areas. The motor enclosure is designed in such a way that no internal
explosion can be transmitted to the explosive atmosphere
surrounding the machine. The enclosure will withstand, without
damage, any pressure levels caused by an internal explosion.
The temperature of the motor’s external enclosure should not exceed

the self-ignition temperature of the explosive atmosphere of the
installation area during operation. No motor device outside the
flameproof area shall be a potential source of sparks, arcs or
dangerous overheating.
Variants combining two types of protection usually combine ‘d’ and

‘e’ types of protection. The most commonly used and recognised by
the CENELEC European Standards is the EEx de variant. The motor
is designed with an EEx d flameproof enclosure, while the terminal
box features an EEx e increased safety protection. Such design
combines the superior safety degree of the ‘d’ type of protection with
the less stringent electrical connection requirements of increased
safety motors.
Increased Safety Design - EEx e

The design of this motor type prevents the occurrence of sparks,
arcs or hot spots in service, that could reach the self-ignition
temperature of the surrounding, potentially explosive atmosphere, in
all inner and outer parts of the machine.
Non-Sparking Design – EEx nA, Ex nA, Ex N

These motors are designated for operation in Zone 2 hazardous
areas. The motor construction is similar to standard TEFV motors,
but with special attention to eliminate production of sparks, arcs or
dangerous surface temperatures.
The British Standard is the type Ex N version. The marking according

to standard EN 50021 is EEx nA, where EEx n = European standard
for Ex product with protection ‘n’, A = for non-sparking equipment.

Motors
The classification parameters of motors for hazardous areas can be

summarised as below:
Fig. 9.8a Overview of classification
EEx d/EEx de
parameters EEx e
EEx p
Severe Zone 2
environments Accidental Standards
presence IEC
Reinforced BS
protection EN
Zone 1
Corrosive Incidental
atmospheres presence
Zone 0
Permanent
presence
Ex nA
Ex N
EEx e
T6 85° C
T5 100° C
T4 135° C
T3 200° C
T2 300° C
T1 450° C
Environment Group Gas
Mines I Methane
Explosive atmospheres IIA Propane
Other than mines IIB Ethane
IIC Hydrogen
9.9 Energy Efficient Motors

In October 1998, the European Union and CEMEP (The European
Committee of Manufacturers of Electrical Machines and Power
Electronics) agreed to introduce three efficiency classes for electric
motors. This agreement forms part of the European Commission’s
aims to improve energy efficiency and reduce CO2 emissions. The
burning of fossil fuels to generate electricity, primarily consumed by
households and industry, is a major source of greenhouse gas
emissions. Industry will, therefore, have a major part to play in
reducing harmful emissions. For instance by increasing the efficiency
of their production processes, and installing energy efficient devices,
industrial processes will consume less electricity. This, in turn, will
reduce the amount of electricity that must be generated to meet
demand.

Motors
Motors account for around 65% of the electric energy consumed in

industrial applications. Energy saving is dependent upon the kW
rating of the motor, the loading and the hours run. As such, higher
efficiency motors can play a significant part in reducing CO2
emissions. An energy efficient motor produces the same output
power (torque) but uses less electrical input power (kW) than a
standard electric motor. This higher efficiency is achieved by using
higher quality and thinner laminations in the stator to reduce core loss
and more copper in the slots to reduce current and resistance losses.
The three efficiency classes designated EFF1, EFF2 and EFF3, apply
to TEFV, 2 and 4 pole, squirrel cage induction motors in the power
range 1.1 to 90 kW (1.5 to 125 hp) rated for 400 volts, 50 Hz.
For intermittent usage, EFF3 class motors can be used and for
continuous usage EFF1 or EFF2 motors should be used.
Table 9.9a
2 pole Motor
Output Power Efficiency %
kW hp EFF1 EFF2 EFF3
equal to equal to below
or above or above
1.1 1.5 82.8 76.2 76.2

1.5 2 84.1 78.5 78.5
2.2 3 85.6 81.0 81.0
3 4 86.7 82.6 82.6
4 5.5 87.6 84.2 84.2
5.5 7.5 88.6 85.7 85.7
7.5 10 89.5 87.0 87.0
11 15 90.5 88.4 88.4
15 20 91.3 89.4 89.4
18.5 25 91.8 90.0 90.0
22 30 92.2 90.5 90.5
30 40 92.9 91.4 91.4
37 50 93.3 92.0 92.0
45 60 93.7 92.5 92.5
55 75 94.0 93.0 93.0
75 100 94.6 93.6 93.6
90 125 95.0 93.9 93.9

Motors
Table 9.9b
4 pole Motor
Output Power Efficiency %
kW hp EFF1 EFF2 EFF3
equal to equal to below
or above or above
1.1 1.5 83.8 76.2 76.2

1.5 2 85.0 78.5 78.5
2.2 3 86.4 81.0 81.0
3 4 87.4 82.6 82.6
4 5.5 88.3 84.2 84.2
5.5 7.5 89.2 85.7 85.7
7.5 10 90.1 87.0 87.0
11 15 91.0 88.4 88.4
15 20 91.8 89.4 89.4
18.5 25 92.2 90.0 90.0
22 30 92.6 90.5 90.5
30 40 93.2 91.4 91.4
37 50 93.6 92.0 92.0
45 60 93.9 92.5 92.5
55 75 94.2 93.0 93.0
75 100 94.7 93.6 93.6
90 125 95.0 93.9 93.9
9.10 Speed Control

The effective speed control of AC electric motors has long been
regarded as an adaptable and economical means of reducing costs
and saving energy.
Speed control can be Multi-Speed

multi-speed, variable voltage Pole Change (Tapped or Dahlander)
or frequency converter. These have a single winding and two speeds in a ratio of 2:1 and can
be supplied for constant torque or variable torque applications.
PAM (Pole Amplitude Modulation)

Similar to above except that pole variations can be 4/6 or 6/8.
Dual Wound
Motors have two separate windings and can be supplied for any two
speed combinations.
A combination of dual and pole change windings can give 3 or 4

speeds from one design.

Motors
Variable Voltage
Variable voltage control provides a low capital cost means of varying
the motor speed on centrifugal pumps. This form of speed control
requires greater derating than for converter drives and is best suited
to 4 pole machines of 2:1 speed reduction with close matching of
motor output to absorbed pump load. These motors are of special
design – standard motors being unsuitable.
Frequency Converter
The use of a frequency converter will allow speed control of a
standard AC motor by adjusting the frequency, although some
derating may be necessary. Basic frequency converters will permit
operation over a typical speed range of 20:1. With increasing
sophistication such as ‘vector’ control, e.g. field oriented control
utilising closed loop feedback; the effective speed range can be
increased to 1000:1.
For applications using variable torque loads such as centrifugal

pumps, very little derating will be required. For applications using
constant torque loads such as rotary lobe pumps, the level of
derating will depend on the speed range required.
The motor ratings must take into account the following:
• Increased heating due to the harmonic content of the inverter

waveforms.
• Reduced cooling arising from motor speed reduction.
• The power or torque requirements throughout the entire

speed range.
• Other limiting factors such as maximum motor speeds,

ambient temperature, altitude etc.
As well as motors being remotely controlled by frequency converters,

electric motors can be made available with the frequency converter
already fitted to the motor. These arrangements are generally
available for motors up to 7.5 kW (10 hp) and have the advantage of
not using any shielded motor cables, as there are no extra
connections between the frequency converter and motor. Also
providing room in a switch cabinet will not be necessary.

Motors
9.11 Changing Motor Nameplates

- Centrifugal and Liquid Ring Pumps only
In some instances there are non-standard electrical requirements
regarding combinations of supply voltage, frequency and output
power. When selecting a motor for a centrifugal or liquid ring pump,
special attention should be given to the rated speed and output
power.
As viewed from table below which shows an example for a motor

frame size 90LB, the rated speed and output power will vary
dependent upon the combination of supply voltage and frequency.
For complete list see section 14.8. It is therefore very important to
specify supply voltage, frequency and required power, to correctly
size the motor.
Motor Frequency Supply Voltage Output Motor Rated Power Rated

Frame Hz v Power Nameplate Speed Factor Current
Size kW rev/min A
90LB 50 220-240D/380-420Y 2.2 Standard 2900 0.85 8.1/4.7

200D 2.2 New 2860 0.90 8.7
90LB 60 440-480Y 2.5 Standard 3500 0.86 4.4
200D 2.1 New 3430 0.91 8.3
220D 2.3 New 3470 0.90 7.5
380Y 2.3 New 3450 0.91 4.8
Table 9.11a
Standard supply voltage, frequency and output power

The motors can be used in the standard version without any
modifications for the standard supply voltage, frequency and output
power combinations. This is shown in section 9.1. For example, if
using a motor frame size 90LB, from the table above, the motor can
be used as standard as follows:
50 Hz, 220-240vD/380-420vY, 2.2 kW
60 Hz, 440-480vY, 2.5 kW
Non-standard supply voltage, frequency and output power

If a non-standard combination of supply voltage, frequency and
output power is required, the standard motor with a new nameplate
or a special motor with an appropriately stamped nameplate can be
used. Examples of this are as follows using a motor frame size 90LB
from the table above.

Motors
Example 1 1. Use a standard motor frame size 90LB.

- For 60 Hz, 380vY, 2.2 kW 2. The appropriate electrical data must be changed on the motor
nameplate.
3. The motor will give an output power of 2.3 kW, which is
sufficient, as 2.2 kW is required.
Example 2 1. The standard motor frame size 90LB will only give 2.3 kW,
– For 60 Hz, 380vY, 2.5 kW which is not sufficient.
2. Select the nearest larger standard motor i.e. frame size
100LB. This will give 3.2 kW, which is sufficient, as 2.5 kW is
required. The appropriate electrical data must be changed on
the motor nameplate.
3. Alternatively select a specially wound motor to give the
required 2.5 kW at the non-standard supply voltage and
frequency combination.

Motors

Cleaning Guidelines for use in Processes utilising CIP Systems
10. Cleaning Guidelines for use in Processes

utilising CIP (Clean In Place) Systems
This section provides cleaning guidelines for use in processes

utilising CIP (Clean In Place) systems. Interpretations of
cleanliness are given and explanations of the cleaning cycle.
The following recommendations offer advice on how to maximise the

CIP (Clean In Place) efficiency of the Alfa Laval ranges of centrifugal
and rotary lobe pumps. The guidelines incorporate references to
internationally recognised cleaning detergents, velocities,
temperatures and pressures used to clean other types of flow
equipment, such as valves and fittings, but have been specifically
prepared to maximise the CIP effectiveness of our pumps.
The perception of the word clean will vary from customer to

customer and process to process. The four most common
interpretations of ‘Clean’ are given below:
1. Physical Cleanliness
This is the removal of all visible dirt or contamination from a surface.
This level of cleanliness is usually verified by a visual test only.
2. Chemical Cleanliness
This is defined as the removal of all visible dirt or contamination as
well as microscopic residues, which are detectable by either taste or
smell but not by the naked eye.
3. Bacteriological Cleanliness
This can only be achieved with the use of a disinfectant that will kill all
pathogenic bacteria and the majority of other bacteria.
4. Sterility
Quite simply this is the destruction of all known micro-organisms.
The following recommendations for CIP will address the first three
definitions.

In most installations it is important to ensure the maximum recovery

of pumped product residues from the production line at the end of
each production run. Where this is a requirement, consideration
should be given to mounting rotary lobe pumps with ports in the
vertical plane to maximise drainability. This will minimise any product
loss, ease the cleaning of the system and reduce the requirement to
dispose of or recycle the wash from the initial cleaning cycles. By
maximising the recovery of product from the system both the
efficiency of the production and cleaning processes will be increased.
Rotary lobe pumps are rarely used as the supply pump for CIP fluids.
Centrifugal pumps are generally used during CIP for each phase of the
cleaning cycle. For the majority of CIP cycles it is recommended that
a differential pressure of 2 to 3 bar is created across the pump to
promote efficient cleaning, whilst it is rotating at it’s normal operating
speed. In many cases a valve is employed in the discharge line of the
system to create the differential pressure across the pump and a
by-pass loop installed around the pump to divert any excess of CIP
liquid that the pump is unable to transfer. The valve(s) setting may be
fluctuated during the CIP cycle to promote pressure/flow variations
that may enhance the cleaning process.
During the CIP cycle there must always be sufficient flow of cleaning
fluid being delivered by the CIP pump to make sure that the
centrifugal or rotary lobe pump is neither starved of liquid at it’s inlet
due to its own flow capability, or overpressurised at it’s inlet due to its
tendency to act as a restriction if it is unable to transfer the full flow of
the fluid being delivered to it.
Internationally accepted protocol for CIP suggest that during all

phases of the CIP cycle a pipeline velocity of between 1.5 m/sec and
3.0 m/sec is required. Velocities within this range have proven to
provide effective cleaning of Alfa Laval pumps, although as a general
rule the higher the velocity the greater the cleaning effect.
Generally the most effective cleaning processes incorporate five

stages:
1. An initial rinse of clean, cold water.

2. Rinsing with an alkaline detergent.
3. Intermediate rinse with cold water.
4. Rinsing with an acidic disinfectant.
5. Final rinse with clean cold water.

The cycle times, temperatures, cleaning mediums and concentrations

of the detergents used will all influence the effectiveness of the
cleaning cycle and care must be taken when defining these to ensure
that they are suitable for use with the particular product being
pumped. Of equal importance is the chemical compatibility between
the cleaning detergents and the product wetted materials in the pump
head and ensuring for rotary lobe pumps the correct temperature
clearance rotors are fitted for the CIP cycle. Consideration should
also be given to the disposal or recycling of used cleaning liquids and
the potential requirement for handling concentrated detergents.
Specialists suppliers should make the final selection of cleaning
detergents/disinfectants.
Within these guidelines a typical cleaning cycle would be as follows:
1. Rinse with clean water at ambient temperature to remove any

remaining residue. 10 to 15 minutes are usually sufficient for
this part of the cycle but this will depend on the condition and
volume of the residue to be removed.
2. Rinse with an alkaline detergent, typically a 2.5% solution of

Caustic Soda (NaOH) at between 70 to 95°C (158 to 203oF)
for a period of 20 to 30 minutes would be used. It is also
common to add a wetting agent (surfactant) to lower the
surface tension of the detergent and hence aid its cleansing
ability. This phase of the cleaning cycle should dissolve and
remove organic matter such as fats and proteins.
3. Intermediate rinse with clean water at ambient temperature for

a period of 5 to 10 minutes. This phase should remove any
residual detergents.
4. Rinse with an acidic disinfectant, typically a 2.5% solution of

Nitric Acid (HNO3) at ambient temperature for a period of 10
to 15 minutes would be used. This phase of the cleaning
cycle should remove proteins, mineral salts, lime and other
deposits.
5. Final rinse with clean water at ambient temperature for a

period of 10 to 15 minutes or until all traces of the cleaning
fluid have been removed.

During the CIP cycles it is important that the required concentration of

cleaning detergents is maintained consistently. A significant increase
in concentration could cause damage to pumps and other
components in the system. A significant decrease in concentration
could effect the detergents cleaning efficiency. A facility for monitoring
and adjusting the detergent concentration should be considered.
Cautionary Notes:
1. Pumps and other equipment installed in CIP systems have

components within them that will expand and contract at
different rates. Care should be taken not to subject them to
rapid temperature cycling.
2. Products containing particulate such as fibre, seeds or soft

fleshy matter have to be evaluated carefully and on an
individual basis, as the nature of these will provide an
increased cleaning challenge. These types of product may
typically require increased cleaning cycle times and/or
increased velocities and pressures during the cleaning cycle.
3. CIP detergent liquids and the elevated temperatures typically

used for CIP processes can cause a potential health risk.
Always adhere to site Health and Safety regulations.
4. Always store and dispose of cleaning agents in accordance

with site Health and Safety regulations.
After CIP cleaning and additional sterilisation in place process (SIP)

may be required when highly sensitive products are handled,
inactivating any micro-organisms which might be still present in the
pump. The sterilisation can be carried out be means of chemicals, hot
water or steam. In the dairy industry the sterilisation temperature is
approximately 145oC (293oF).

Compliance with International Standards and Guidelines
11. Compliance with International

This section describes some of the international standards and
guidelines applicable to Alfa Laval pump ranges.
In recent years there has been A number of countries have national standards and/or directives
increasing concern over applicable to food machinery but there are relatively few international
safety and hygiene in the standards. Those that exist are predominantly dairy based and are
bio-pharmaceutical and food too general and developed on ‘experience’ rather than scientific data.
industries. This has led to In the USA, a number of guidelines in the form of third party approval
numerous standards and schemes have been developed for the dairy industry (3-A standards)
legislation being written. and food service equipment (NSF – National Sanitation Foundation).
The structure of these schemes involves representatives of
equipment manufacturers, end users and regulatory bodies in the
implementation of recommendations. Unfortunately, however the 3-A
standards have no benchmark of cleanability or test regimes to
establish cleanability, and the NSF standards are not applicable to the
hygienic design of general food processing equipment.
Alfa Laval pump ranges are available to meet standards and

legislation as follows:
• CE Compliance (Safety/Risk Assessment).
• 3-A Design and Material Specifications (Centrifugal and

Positive Rotary Lobe Pumps for Milk and Milk Products).
• FDA Material Requirements.
• USDA Regulating Biotechnology.
• EN 10204 3.1.B Certified Material Traceability.
• EN 10204 2.2 Certificate of Conformity.
• EHEDG Cleanability and Installation Guidelines.

CE
The introduction of CE marking is to demonstrate to interested
parties that goods or equipment with this mark comply with the
appropriate directives of the European Community. The appropriate
directives are those that are concerned with the design and
manufacture of goods or equipment. Directives are intended to
facilitate a Single Market in the European Union. With emerging
European standardisation, conflicting national standards will
Fig. 11a CE eventually tend to disappear, as all EU member states will work to the
same standard, with a few exceptions. Some national differences
cannot be harmonised. In Europe many different languages are
spoken, and some parts are prone to earthquakes, high winds, heavy
snow and extremes of cold and heat. It is often uneconomic to design
equipment that will withstand all these conditions.
All Alfa Laval pump ranges are CE marked and conform to the
machinery directive 89/392/EEC as amended by 91/368/EEC, 93/
44/EEC and 93/68/EEC and other relevant directives i.e. ‘Electrical
Equipment Low Voltage Directive 73/23/EEC’ and ‘Electromagnetic
Compatibility Directive 89/336/EEC’.
Other applicable standards/specifications which Alfa Laval pump

ranges comply to are as follows:
• EN292 Parts 1 and 2: 1991 Safety of Machinery - Basic

concepts, general principles for design.
• EN294: 1992 Safety distances to prevent danger zones

being reached by the upper limbs.
• EN60204 Part 1: 1993 Safety of Machinery - Electrical

equipment of machines - specification for general
requirements.
• BS5304: 1988 Code of Practice for Safety of Machinery.
• ISO9001: 1994 Quality Management System.

3-A (Centrifugal and Positive Rotary Pumps for Milk

and Milk Products)
This standard has the purpose of establishing and documenting the
material, fabrication, and installation (where appropriate) requirements
for the engineering design and technical construction files for all
products, assemblies, and sub-assemblies supplied by the
manufacturer. The manufacturer has to be in compliance with the
sanitary criteria found in 3-A Sanitary Standards or 3-A Accepted
Fig. 11b 3-A Practices. The 3-A Sanitary Standards and 3-A Accepted Practices
are voluntarily applied as suitable sanitary criteria for dairy and food
processing equipment.
All Alfa Laval pump ranges conform to this 3-A standard.
FDA
The Food and Drug Administration (FDA) in the USA is the
enforcement agency of the United States Government for food, drug
and cosmetics manufacturing. It is responsible for new material
approvals, plant inspections and material recalls. In the USA, the
‘Food, Drug and Cosmetic Act’ requires food, drug and cosmetic
manufacturers to prove that their products are safe. The FDA’s
primary purpose is to protect the public by enforcing this Act.
The FDA can:

• approve plants for manufacturing.
• inspect plants at random.
• write general guidelines for good manufacturing processes.
• write specific criteria for materials in product contact.
• have certain expectations regarding design practices.
The FDA cannot:

• approve equipment outside of a particular use within a specific
system.
• approve materials for use in pharmaceutical systems.
• write specific engineering or design requirements for systems.
For all Alfa Laval pump ranges

the product wetted parts can
be made available with FDA
compliance.

All Alfa Laval pump ranges USDA

can be supplied into process The United States Department of Agriculture (USDA) is one of three
areas/plants that are Federal Agencies, along with the Environmental Protection Agency
controlled by USDA. (EPA) and the U.S. Food and Drug Administration (FDA), primarily
responsible for regulating biotechnology in the United States.
Products are regulated according to their intended use, with some
products being regulated under more than one agency.
Agricultural biotechnology is a collection of scientific techniques,

including genetic engineering, that are used to create, improve, or
modify plants, animals, and micro-organisms. Using conventional
techniques, such as selective breeding, scientists have been working
to improve plants and animals for human benefit for hundreds of
years. Modern techniques now enable scientists to move genes (and
therefore desirable traits) in ways they could not before - and with
greater ease and precision.
The Federal government has a well co-ordinated system to ensure

that new agricultural biotechnology products are safe for the
environment and to animal and human health. While these agencies
act independently, they have a close working relationship.
• USDA’s Animal and Plant Health Inspection Service (APHIS) is

responsible for protecting American agriculture against pests
and diseases. The agency regulates the field testing of
genetically engineered plants and certain micro-organisms.
APHIS also approves and licenses veterinary biological
substances, including animal vaccines that may be the
product of biotechnology.
• USDA’s Food Safety and Inspection Service (FSIS) ensures

the safety of meat and poultry consumed as food.
• The Department of Health and Human Service’s Food and

Drug Administration (FDA) governs the safety and labelling of
drugs and the nation’s food and feed supply, excluding meat
and poultry.
• The Environmental Protection Agency (EPA) ensures the

safety and safe use of pesticidal and herbicidal substances in
the environment and for certain industrial uses of microbes in
the environment.

• The Department of Health and Human Service’s National

Institutes of Health have developed guidelines for the
laboratory use of genetically engineered organisms. While
these guidelines are generally voluntary, they are mandatory
for any research conducted under Federal grants and they are
widely followed by academic and industrial scientists around
the world.
The Alfa Laval Rotary Lobe EN 10204 3.1.B

pump ranges and the With the stringent demands of hygiene within new food and
LKH-UltraPure range of pharmaceutical plants being built, material traceability of equipment
Centrifugal pumps can be supplied is increasingly important. The EN 10204 standard defines
supplied with material the different types of inspection documents required for metallic
traceability if required. products. In particular, 3.1.B of this standard refers to inspection
documents being prepared at each stage of manufacture and
supervised tests performed by authorised personnel independent of
the manufacturer.
EN 10204 2.2
This standard defines documents supplied to the purchaser, in
accordance with the order requirements, for the supply of metallic
products such as pumps. This takes the form of a certificate of
conformity and can be applied to all Alfa Laval pump ranges.
EHEDG
We are now seeing increased public awareness surrounding food
hygiene and food manufacturers desire to improve product safety.
With no European Community legislation available the European
Hygienic Equipment Design Group (EHEDG) was formed. EHEDG
aims to promote hygiene during the processing and packaging of
food products.
Fig. 11c EHEDG EHEDG objectives are to produce hygienic design guidelines that can
be verified by standard test procedures. This requires a range of test
procedures for a variety of equipment parameters including
cleanability, pasteurisability, sterilisability and aseptic capability.
The Alfa Laval LKH range of

centrifugal pumps and the SX
range of rotary lobe pumps
with its dedicated vertical port
orientation meet EHEDG
cleanability and comply with
EHEDG installation
guidelines.


Installation Guide
12. Installation Guide

This section covers guidelines relating to pump installation,
system design and pipework layout.
12.1 General
12.1.1 System Design
To ensure optimum pump operation it is important that any pump unit
is installed correctly. When designing a pumping system the following
should be taken into consideration:
• Confirm the Net Positive Suction Head (NPSH) available from

the system exceeds the NPSH required by the pump, as this
is crucial for ensuring the smooth operation of the pump and
preventing cavitation.
• Avoid suction lifts and manifold/common suction lines for two

Discharge
line rotary lobe pumps running in parallel, as this may cause
vibration or cavitation (see fig. 12.1.1a).
Plan view
Suction line
Fig. 12.1.1a Avoid common suction lines

• Protect the pump against blockage from hard solid objects
e.g. nuts, bolts etc. Also protect the pump from accidental
operation against a closed valve by using relief valves,
pressure switches and current limiting devices.
• Fit suction and discharge pressure monitor points for

diagnostic purposes.
• Fit valves, if two pumps are to be used on manifold/common

discharge lines.

Installation Guide
• Make the necessary piping arrangements if flushing is required

for the seal or if a media is required for heating/cooling jackets.
• Adhere to installation foundation instructions.
• Do not subject rotary lobe pumps to rapid temperature

changes, as pump seizure can result from thermal shock.
12.1.2 Pipework
All pipework must be supported. The pump must not be allowed to
support any of the pipework weight and the following should be taken
into consideration.
• Have short straight inlet pipework to reduce friction losses in

the pipework thereby improving the NPSH available.
• Avoid bends, tees and any restrictions close to either suction

or discharge side of pump. Use long radius bends wherever
possible.
• Provide isolating valves on each side of the pump when

necessary.
• Keep pipework horizontal where applicable to reduce air

locks. Include eccentric reducers on suction lines.
12.1.3 Weight
The weight of the pump and drive unit should be considered for lifting
gear requirements.
12.1.4 Electrical Supply

Ensure that there is an adequate electrical supply close to the pump
drive unit. This should be compatible with the electric motor selected.

Installation Guide
12.2 Flow Direction

Outlet 12.2.1 Centrifugal Pumps
A centrifugal pump should never be operated in the wrong direction
of rotation with fluid in the pump. It is possible to check this in two
ways as follows:
Inlet
Fig. 12.2.1a Correct direction of flow
1. Pump with impeller screw fitted

• Start and stop the motor momentarily (without fluid in the
pump).
• Ensure that the direction of rotation of the motor fan is
clock-wise as viewed from the rear end of the motor.
Fig. 12.2.1b Pump with impeller screw

fitted
2. Pump without impeller screw fitted

With this method the impeller should always be removed before
checking the direction of rotation.
The pump should never be started if the impeller is fitted and the
pump casing has been removed.
Fig. 12.2.1c Pump without impeller

screw fitted
• Start and stop the motor momentarily.

• Ensure that the direction of rotation of the stub shaft is
anti-clockwise as viewed from the pump inlet.
Stub shaft
Fig. 12.2.1d Pump without impeller

Installation Guide
12.2.2 Rotary Lobe Pumps

The direction of flow is dictated by the direction of drive shaft
rotation. Reversing the direction of rotation will reverse the flow
direction.
Outlet Inlet Outlet
Inlet Outlet
Outlet Inlet
Fig. 12.2.2a Flow direction

Installation Guide
12.3 Baseplate Foundations

(Rotary Lobe Pumps only)
Rotary Lobe pumps when supplied with a drive unit are normally
mounted on a baseplate. Alfa Laval standard baseplates have
pre-drilled fixing holes to accept base retaining bolts.
To provide a permanent rigid support for securing the pump unit, a

Baseplate fixing holes foundation is required which will also absorb vibration, strain or shock
on the pumping unit.
Fig. 12.3a Baseplate fixing Methods of anchoring the baseplate to the foundation are varied, they
can be studs embedded in the concrete either at the pouring stage as
shown below, or by use of epoxy type grouts. Alternatively
mechanical fixings can be used.
The Foundation should be approximately 150mm longer and wider

than the baseplate. The depth of the foundation should be
proportional to the size of the complete pump unit. For example, a
large pump unit foundation depth should be at least 20 times the
diameter of the foundation bolts.
The drawing below shows two typical methods for foundation bolt
retaining. The sleeve allows for ‘slight’ lateral movement of the bolts
after the foundation is poured. Rag or waste paper can be used to
prevent the concrete from entering the sleeve while the foundation is
poured. A minimum of 14 days is normally required to allow the
curing of the concrete prior to pump unit installation.
D = Diameter of foundation bolts

Fig. 12.3b Foundations

Installation Guide
12.4 Coupling Alignment

(Rotary Lobe Pumps only)
Before rotary lobe pump units are installed it is important to ensure
that the mounting surface is flat to avoid distortion of the baseplate.
This will cause pump/motor shaft misalignment and pump/motor unit
Parallel misalignment damage. Once the baseplate has been secured, the pump shaft to
motor shaft coupling alignment should be checked and adjusted as
necessary. This is achieved by checking the maximum angular and
parallel allowable misalignments for the couplings as stated by the
Angular misalignment
coupling manufacturers.
Fig. 12.4a Parallel and angular
misalignment
12.5 Special Considerations for Liquid

Ring Pumps
12.5.1 Pipework
The pipelines on the discharge side of a liquid ring pump should be
routed as shown below to ensure correct pump operation.
Min. 1 m
Min. 2 m
(3.3 ft)
(6.6 ft)
Fig. 12.5.1a Installation of MR-166S/ Fig. 12.5.1b Installation of MR-300

-185S/-200S

Troubleshooting
13. Troubleshooting
This section offers possible causes and solutions to most
common problems found in pump installation and operation.
13.1 General
In most pumping systems, pumps are likely to be the most vulnerable
components. The symptoms frequently show the pump to be at fault
regardless of what may be wrong. The problem is usually caused by
inadequate control of the pumped fluid or a change in operating
requirements of which the system or pump is not capable of handling
or a component malfunction.
Diagnosis of problems will be Before starting to correctly identify the problem it is important to
greatly assisted by having gather as much information relating to the process as follows:
pressure gauges fitted to both
pump inlet and outlet. • Reconfirm original duty conditions.
• What has changed in the process since operation was last
satisfactory? i.e. pressure, temperature, fluid viscosity etc.
• Was the system undergoing routine maintenance?
• Were any new or repaired components omitted to be fitted?
• When was the pump last serviced?
• What was the appearance and condition of the pump internal
components?
• How long did the pump operate before the problem?
• Any changes in pump noise or vibration?
The most common problems found are generally as follows and

explained in 13.2:
• Loss of flow.
• Loss of suction.
• Low discharge pressure.
• Excessive noise or vibration.
• Excessive power usage.
• Rapid pump wear.
• Seal leakage.

Troubleshooting
13.2 Common Problems

13.2.1 Loss of Flow
A simple cause of this could be incorrect direction of shaft rotation,
which although obvious is often overlooked. Loss of flow can be
caused by excessive discharge pressure and/or by a change in fluid
viscosity.
In general terms:
• For a rotary lobe pump if the viscosity is significantly reduced,
the pump’s rated flow will be reduced, more so for higher
pressure operation.
• For a centrifugal pump if the viscosity is increased, the pump’s
rated flow will be decreased.
13.2.2 Loss of Suction

Loss of suction can be minor, causing little short term damage or
sufficiently major to cause catastrophic damage. Loss of suction
means fluid is not reaching the pumping elements or not reaching
them at a sufficiently high pressure to keep the fluid being pumped in
a fluid state. Loss of suction can be interpreted as the inability to
prime, cavitation or a gas content problem.
The rotary lobe pump can be classed as ‘self-priming’. This means

that within limits, it is capable of evacuating (pumping) a modest
amount of air from the suction side of the pump to the discharge side
of the pump. Filling the inlet system with fluid or at least filling the
pump (wetted pumping elements) will make a major improvement in
the pump’s priming capability.
The liquid ring pump can also be classed as self-priming when the
pump casing is half filled with fluid and the LKHSP centrifugal pump
range is specially designed to be self-priming.
Cavitation is caused by insufficient system inlet pressure to the pump.

This can be caused by an inlet system restriction, excessive fluid
viscosity or excessive pump speed. Inlet restrictions can include dirty
or clogged inlet strainers, debris floating in the fluid supply that covers
the inlet piping intake, or rags. If the fluid is cooler than design
temperature, its viscosity may be too high causing excessive friction
(pressure loss) in the inlet piping system. Cavitation is frequently
accompanied by noise, vibration and significant increase in discharge
pressure pulsation. If a pump is allowed to cavitate over long periods
this will cause damage to the pumphead components. The surface of
these components are typically perforated and pitted.

Troubleshooting
Gas in the inlet pipework has the same impact on pump operation
and creates the same symptoms as cavitation. This can occur under
other circumstances such as a pump operating at an inlet pressure
below local atmospheric pressure. In this instance it is quite likely that
air is being drawn into the pipework through a loose pipe connection
or pump casing joint, leaking inlet valve stem, defective or otherwise
damaged joint gasket in the pipework system. In recirculating
systems, such as a lubrication system where the fluid pumped is
continuously returned to a supply source or tank, if the tank and
return lines are not adequately designed, located and sized, air is
easily entrained in the oil and immediately picked up by the pump inlet
system. Be sure fluid level at its source is at or above minimum
operating levels. Lines returning flow to a supply tank should
terminate below minimum fluid level.
13.2.3 Low Discharge Pressure

Low discharge pressure can only be caused by loss of flow. Pump
discharge pressure is caused only by the system’s resistance to the
flow provided by the pump. Either the pump is not providing the flow
expected or the system is not offering the expected resistance to
that flow. It is possible that flow is being restricted into the pump
(cavitation), usually accompanied by noise and vibration, the pump is
not producing its rated flow (pump worn or damaged), or the pump
flow is bypassing rather than being delivered into the system as
intended.
13.2.4 Excessive Noise or Vibration

Excessive noise and/or vibration can be a symptom of cavitation,
mechanical damage to pump assembly, misalignment of drive or
harmonics with other elements of the system. Cavitation is especially
true if the discharge pressure is fluctuating or pulsating. Mechanical
causes of noise and vibration include shaft misalignment, loose
couplings, loose pump and/or driver mountings, loose pump and/or
driver guards, worn or damaged driver or pump bearings or valve
noise that seems to be coming from the pump. Valves, especially on
the discharge side of the pump can sometimes go into a hydraulic
vibration mode caused by operating pressure, flow rate and the valve
design. Resetting or a change in an internal valve component is
usually sufficient to solve the problem.

Troubleshooting
13.2.5 Excessive Power

Excessive power consumption can be caused by either mechanical or
hydraulic problems. Mechanical causes include imminent bearing
failure, pumping elements rubbing which can lead to a pump seizure
and poor shaft alignments. Too high viscosity can result in the motor
overloading.
• For a rotary lobe pump too high discharge pressure can

cause the motor to overload.
• For a centrifugal pump too high capacity (too low discharge

pressure) can cause the motor to overload.
13.2.6 Rapid Pump Wear

Rapid wear of pumphead components is either caused by abrasives
being present in the fluid, chemical corrosion, loss of shaft support
(bearing failure), or operation at a condition for which the pump is not
suitable i.e. cavitation, excessively high pressure or high temperature.
To avoid any abrasive foreign material entering the pump, strainers or
filters should be employed wherever possible and practical. Rapid
wear is sometimes not wear in the sense of a non-durable pump, but
really a catastrophic pump failure that occurred very quickly. Looking
at the pump internal parts alone may not provide much help in
identifying the cause, thus the importance of knowing what was
occurring in the time period immediately preceding detection of the
problem.
13.2.7 Seal Leakage

Mechanical seals fitted to centrifugal, rotary lobe and liquid ring
pumps can be seen as the weakest point for any pump leakage and
special care should be taken to ensure the correct seal for the
application is installed i.e. mounting attitude, seal face combination
and elastomer selection.
Apart from mis-selection and poor servicing, seal leakage can be due
to pump cavitation, too high discharge pressure, being allowed to run
dry and unexpected solids in the fluid.

Troubleshooting
13.3 Problem Solving Table

The table shown offers probable causes and solutions to the most
common problems encountered.
In ( ) next to the particular solution given you will find annotation

relating to what pump type the solution is for.
i.e. ce = Centrifugal Pump
liq = Liquid Ring Pump
rlp = Rotary Lobe Pump
See table 13.3a on the following pages:

Troubleshooting
Problem ce = Centrifugal, liq = Liquid Ring, rlp = Rotary Lobe
Excessive power absorbed

Pump stalls when starting
Mechanical seal leakage

Low discharge pressure
Prime lost after starting
Packed gland leakage

Pump element wear
Pump will not prime
Irregular discharge
Noise and vibration

Pump overheats
Motor overheats
Under capacity
Syphoning
No flow
Seizure Probable Causes Solutions
ü ü Incorrect direction of rotation. Reverse motor (ce, liq, rlp).

ü Pump not primed. Expel gas from suction line and pumping chamber
and introduce fluid (ce, liq, rlp).
ü ü üü ü ü Insufficient NPSH available. Increase suction line diameter (ce, liq, rlp).
Increase suction head (ce, liq, rlp).
Simplify suction line configuration and reduce length
(ce, liq, rlp).
Reduce pump speed (rlp).
Decrease fluid temperature (ce,liq) - check effect of
increased viscosity?
ü üü ü ü Fluid vaporising in suction line. Increase suction line diameter (ce, liq, rlp).
Increase suction head (ce, liq, rlp).
Simplify suction line configuration and reduce length
(ce, liq, rlp).
Reduce pump speed (rlp).
Decrease fluid temperature (ce, liq) - check effect of
increased viscosity?
ü ü ü ü ü ü Air entering suction line. Remake pipework joints (ce, rlp).
ü ü ü ü ü Strainer or filter blocked. Service fittings (ce, liq, rlp).
ü ü ü ü ü ü ü ü Fluid viscosity above rated figure. Increase fluid temperature (ce, liq, rlp).
Decrease pump speed (rlp).
Increase motor speed (ce, liq).
Check seal face viscosity limitations (ce, liq, rlp).
ü ü ü Fluid viscosity below rated figure. Decrease fluid temperature (ce, liq, rlp).
Increase pump speed (rlp).
ü üü ü ü Fluid temp. above rated figure. Cool the pump casing (ce, rlp).
Reduce fluid temperature (ce, liq, rlp).
Check seal face and elastomer temperature
limitations (ce, liq, rlp).
ü ü ü Fluid temp. below rated figure. Heat the pump casing (ce,rlp).
Increase fluid temperature (ce,liq, rlp).
üü ü ü Unexpected solids in fluid. Clean the system (ce, liq, rlp).
Fit strainer to suction line (ce, liq, rlp).
If solids cannot be eliminated, consider fitting double
mechanical seals (ce, rlp).
ü ü ü ü ü ü ü ü üü ü ü ü Discharge pressure above rated Check for obstructions i.e. closed valve (ce, liq, rlp).
figure. Service system and change to prevent problem
recurring (ce, liq, rlp).
Simplify discharge line to decrease pressure
(ce, liq, rlp).
ü ü ü ü Gland over-tightened. Slacken and re-adjust gland packing (rlp).

Troubleshooting
Problem ce = Centrifugal, liq = Liquid Ring, rlp = Rotary Lobe
Excessive power absorbed

Pump stalls when starting
Mechanical seal leakage

Low discharge pressure
Prime lost after starting
Packed gland leakage

Pump element wear
Pump will not prime
Irregular discharge
Noise and vibration

Pump overheats
Motor overheats
Under capacity
Syphoning
No flow
Seizure
Probable Causes Solutions
ü ü ü ü ü Gland under-tightened. Adjust gland packing (rlp).

ü ü Seal flushing inadequate. Increase flush flow rate (ce,rlp).
Check that flush fluid flows freely into seal area
(ce, rlp).
ü ü ü ü Pump speed above rated figure. Decrease pump speed (rlp).
ü ü Pump speed below rated figure. Increase pump speed (rlp).
ü ü ü ü ü ü ü Pump casing strained by Check alignment of pipes (ce, liq, rlp).
pipework. Fit flexible pipes or expansion fittings (ce, liq, rlp).
Support pipework (ce, liq, rlp).
ü ü ü ü Flexible coupling misaligned. Check alignment and adjust mountings accordingly
(rlp).
ü ü ü ü ü ü Insecure pump driver mountings. Fit lock washers to slack fasteners and re-tighten
(rlp).
ü ü ü ü ü ü ü ü Shaft bearing wear or failure. Refer to pump maker for advice and replacement
parts (rlp).
ü ü ü ü ü ü Insufficient gearcase lubrication. Refer to pump maker’s instructions (rlp).
ü ü ü ü ü ü ü ü Metal to metal contact of Check rated and duty pressures (ce, liq, rlp).
pumping element. Refer to pump maker (ce, liq, rlp).
ü ü ü Worn pumping element. Fit new components (ce, liq, rlp).
ü ü ü Rotorcase cover relief valve Check pressure setting and re-adjust if necessary
leakage. (rlp).
Examine and clean seating surfaces (rlp).
Replace worn parts (rlp).
ü ü Rotorcase cover relief valve Check for wear on sealing surfaces, guides etc -
chatter. replace as necessary (rlp).
ü ü Rotorcase cover relief valve Re-adjust spring compression (rlp) - valve should lift
incorrectly set. approx. 10% above duty pressure.
ü ü Suction lift too high. Lower pump or raise fluid level (ce, rlp).
ü ü Fluid pumped not compatible Use optional materials (ce, liq, rlp).
with materials used.
ü No barrier in system to prevent Ensure discharge pipework higher than suction tank
flow passing back through pump. (rlp).
ü ü Pump allowed to run dry. Ensure system operation prevents this (ce, rlp).
Fit single or double flushed mechanical seals (ce, rlp).
Fit flushed packed gland (rlp).
ü ü Faulty motor. Check and replace motor bearings (ce, liq, rlp).
ü ü Too large clearance between Reduce clearance between impeller and back plate/
impeller and back plate/casing. casing (ce, liq).
ü ü Too small impeller diameter. Fit larger size impeller - check motor size (ce).
ü Pumping element missing i.e. Fit pumping element (ce, liq, rlp).
after service.
Table 13.3a

Troubleshooting

Technical Data
14. Technical Data

This section includes a summary of nomenclature and formulas
used in this handbook. Various conversion tables and curves are
also shown.
14.1 Nomenclature
Symbol Description Symbol Description
A Area QL Fluid losses through impeller

casing clearances
D Tube diameter q Pump displacement
F Force r Radius
fD Darcy friction factor Ra Surface roughness
g Gravity Re Reynolds number
H Total head SG Specific gravity
Hs Total suction head T Shaft torque
Ht Total discharge head V Fluid velocity
hfs Pressure drop in suction line g (Greek letter ‘gamma’) Specific weight
hft Pressure drop in discharge line D (Greek letter ‘delta’) Total
hs Static suction head Î (Greek letter ‘epsilon’) Relative roughness
ht Static discharge head h (Greek letter ‘eta’) Total efficiency
L Tube length hh Hydraulic efficiency
n Pump speed hm Mechanical efficiency
Pa Pressure absolute above fluid level hoa Overall efficiency
Pf Pressure loss due to friction hv Volumetric efficiency
Ps Vacuum or pressure in a tank on m (Greek letter ‘mu’) Absolute viscosity
suction side
Pt Pressure in a tank on discharge side n (Greek letter ‘nu’) Kinematic viscosity
Pv Power/viscosity factor r (Greek letter ‘rho’) Fluid density
Pvp Vapour pressure w (Greek letter ‘omega’) Shaft angular velocity
Q Capacity
Table 14.1a

Technical Data
14.2 Formulas
Designation Formula Comments Where
to find
Product
Viscosity n=m where: 2.1.2

r n = Kinematic viscosity (mm2/s)
m = Absolute viscosity (mPa.s)
r = fluid density (kg/m3)
or
n=m where:
SG n = Kinematic viscosity (cSt)
m = Absolute viscosity (cP)
SG = specific gravity
or
m = n x SG 1 Poise = 100 cP
1 Stoke = 100 cSt
Flow
Velocity V=Q where: 2.1.7

A V = fluid velocity (m/s)
Q = capacity (m3/s)
A = tube area (m2)
or
V = Q x 353.6 where:
D2 V = fluid velocity (m/s)
Q = capacity (m3/h)
or
D2 V = fluid velocity (ft/s)
Q = capacity (US gall/min)
or
D2 V = fluid velocity (ft/s)
Q = capacity (UK gall/min)
Reynolds number Re = D x V x r where: 2.1.7

(ratio of inertia m D = tube diameter (m)
forces to viscous V = fluid velocity (m/s)
forces) r = density (kg/m³)
m = absolute viscosity (Pa.s)
or
Re = D x V x r where:
m D = tube diameter (mm)
V = fluid velocity (m/s)
or
Re = 21230 x Q where:
Dxm D = tube diameter (mm)
Q = capacity (l/min)

Technical Data

to find
Reynolds number or
(ratio of inertia Re = 3162 x Q where:
forces to viscous Dxn D = tube diameter (in)
forces) Q = capacity (US gall/min)
or
Re = 3800 x Q where:
Dxn D = tube diameter (in)
Pressure/Head
Pressure (total force P=F where: 2.2.2

per unit area exerted A F = Force
by a fluid) A = Area
Static Pressure/Head P=rxgxh where: 2.2.2

(relationship between P = pressure/head (Pa)
pressure and r = fluid density (kg/m3)
elevation) g = acceleration due to gravity (m/s2)
or
P = h x SG where:
10 P = pressure/head (bar)
or
P = h x SG where:
2.31 P = pressure/head (psi)
h = height of fluid (ft)
Total head H = Ht – (± Hs) where: 2.2.2

Ht = total discharge head
Hs = total suction head
Total discharge head Ht = ht + hft + pt where: 2.2.2

ht = static discharge head
hft = pressure drop in discharge line
pt > 0 for pressure
pt < 0 for vacuum
pt = 0 for open tank
Total suction head Hs = hs - hfs + (± ps) where: 2.2.2

hs = static suction head
> 0 for flooded suction
< 0 for suction lift
hfs = pressure drop in suction line
ps > 0 for pressure
ps < 0 for vacuum
ps = 0 for open tank
Friction loss Pf = fD x L x r x V² where: 2.2.2

(Miller equation) Dx2 Pf = friction loss (Pa)
fD = friction factor (Darcy)
L = tube length (m)
D = tube diameter (m)

Technical Data

to find
Friction loss or
(Miller equation) Pf = 5 x SG x fD x L x V² where:
D Pf = friction loss (bar)
L = tube length (m)
or
Pf = 0.0823 x SG x fD x L x V² where:
D Pf = friction loss (psi)
L = tube length (ft)
V = fluid velocity (ft/s)
Darcy friction factor fD = 64 where: 2.2.2

Re fD = friction factor
Re = Reynolds number
NPSHa (Net Positive NPSHa = Pa ± hs – hfs – Pvp where: 2.2.4

Suction Head (+hs for flooded suction) Pa = pressure absolute above fluid level
available) (– hs for suction lift) (bar)
hs = static suction head (m)
hfs = pressure drop in suction line (m)
Pvp = vapour pressure (bar a)
or
where:
Pa = pressure absolute above fluid level
(psi)
hs = static suction head (ft)
hfs = pressure drop in suction line (ft)
Pvp = vapour pressure (psia)
Power
Hydraulic power Power (W) = Q x H x r x g where: 7.2.1

(theoretical energy Q = capacity (m3/s)
required) H = total head (m)
or
Power (kW) = Q x H where:
k Q = capacity (l/min)
H = total head (bar)
k = 600
or
Power (hp) = Q x H where:
k Q = capacity (US gall/min)
H = total head (psi)
k = 1715
or
Power (hp) = Q x H where:
k Q = capacity (UK gall/min)
H = total head (psi)
k = 1428

Technical Data

to find
Required power Hydraulic power 7.2.2

(power needed at Efficiency (100% = 1.0)
the pump shaft)
Torque
Torque Torque (Nm) = 7.2.3

Required power (kW) x 9550
or
Torque (Kgfm) =
Required power (kW) x 974
or
Torque (ftlb) =
Required power (hp) x 5250
Efficiency
Hydraulic efficiency Pump head loss (m) x 100% 7.2.4

(hh) Total head (m)3
Mechanical 1 - Pump mech. losses x 100% 7.2.4

efficiency (hm) Required power
Volumetric efficiency hv = Q x 100% where: 7.2.4

(Centrifugal and Q + QL hv = volumetric efficiency
Liquid Ring pumps) Q = pump capacity
QL = fluid losses due to leakage through
the impeller casing clearances
Volumetric efficiency hv = Q x 100% where: 7.2.4

(Rotary Lobe pumps) q hv = volumetric efficiency
Q = pump capacity
q = pump displacement
Pump efficiency Water horse power x 100% 7.2.4

(hp) Required power
or
hp = Q x H x r x g
wxT where:
hp = pump efficiency
Q = capacity (m3/s)
w = shaft angular velocity (rad/s)
T = shaft torque (Nm)
Overall efficiency Water horse power x 100% 7.2.4

(hoa) Drive power

Technical Data

to find
Pump speed - Rotary Lobe Pump
Pump speed n = Q x 100 where: 7.2.4

q x hv x 60 n = pump speed (rev/min)
Q = capacity (m³/h)
q = pump displacement (m³/100 rev)
or
n = Q x 100 where:
q x hv n = pump speed (rev/min)
Q = capacity (US gall/min)
or
n = Q x 100 where:
q x hv n = pump speed (rev/min)
q = pump displacement (UK gall/100 rev)
Flow Control - Centrifugal Pump
Ö
Connection between Q2 where: 7.3.2
3
impeller diameter D2 = D1 x D = impeller diameter (mm)
and capacity Q1 Q = capacity (m³/h)
Ö
Connection between H2 where: 7.3.2
and head H1 H = head (m)
Ö
Connection between 5 P2 where: 7.3.2
and power P1 P = power (kW)
Reduction of where: 7.3.2
Ö
multi-stage impeller c-b D1 = standard diameter (mm)
diameter D2 = D1 x a = max. working point (m)
a-b b = min. working point (m)
c = required working point (m)
Connection between Q2 where: 7.3.2

impeller speed and n2 = n1 x n = impeller speed (rev/min)
capacity Q1 Q = capacity (m³/h)
Ö
Connection between H2 where: 7.3.2
head H1 H = head (m)
Ö
Connection between 3 P2 where: 7.3.2
power P1 P = power (kW)
Table 14.2a

Technical Data
14.3 Conversion tables

14.3.1 Length
mm m cm in ft yd
1.0 0.001 0.10 0.0394 0.0033 0.0011

1000 1.0 100 39.370 3.2808 1.0936
10 0.01 1.0 0.3937 0.0328 0.1094
25.4 0.0254 2.540 1.0 0.0833 0.0278
304.8 0.3048 30.48 12 1.0 0.3333
914.4 0.9144 91.441 36 3.0 1.0
Table 14.3.1a
14.3.2 Volume
m³ cm³ l in³ ft³ UK gall. US gall.
4
1.0 100 x 10 1000 61024 35.315 220.0 264,0
10 x 107 1.0 10 x 10-4 0.0610 3.53 x 10-5 22 x 10-5 26.4 x 10-5
0.0010 1000 1.0 61.026 0.0353 0.22 0.2642
1.64 x 10-5 16.387 0.0164 1.0 58 x 10-5 0.0036 0.0043
00283 28317 28.317 1728 1.0 6.2288 7.4805
0.0045 4546.1 4.546 277.42 0.1605 1.0 1.201
37.88 x 10-4 3785.4 3.7853 231.0 0.1337 0.8327 1.0
Table 14.3.2a
14.3.3 Volumetric Capacity

m³/h l/min hl/h UK gall/min US gall/min ft³/h ft³/s m³/s
-3
1.0 16.667 10.0 3.6667 4.3999 35.315 9.81 x 10 2.78 x 10-4
-4
0.060 1.0 0.60 0.22 0.2642 2.1189 5.88 x 10 1.67 x 10-5
-4
0.10 1.6667 1.0 0.3667 0.4399 3.5315 9.81 x 10 2.78 x 10-5
-3
0.2727 4.546 2.7270 1.0 1.201 9.6326 2.67 x 10 7.57 x 10-5
0.2273 3.785 2.2732 0.8326 1.0 8.0208 2.23 x 10-3 6.31 x 10-5
0.0283 0.4719 0.2832 0.1038 0.1247 1.0 2.78 x 10-4 7.86 x 10-6
101.94 1699 1019.4 373.73 448.83 3600 1.0 0.0283
3600 6 x 104 36000 13200 15838 127208 35.315 1.0
Table 14.3.3a

Technical Data
14.3.4 Mass Capacity

kg/s kg/h lb/h UK ton/h t/d t/h lb/s
(tonne/day) (tonne/hour)
1.0 3600 7936.6 3.5431 86.40 3.6 2.2046

2.78 x 10-4 1.0 2.2046 98.4 x 10-5 0.024 0.001 6.12 x 10-4
1.26 x 10-4 0.4536 1.0 44.6 x 10-5 0.0109 4.54 x 10-4 2.78 x 10-4
0.2822 1016.1 2240 1.0 24.385 1.0160 0.6222
11.57 x 10-3 41.667 91.859 0.0410 1.0 0.0417 0.0255
0.2778 1000 2201.8 0.9842 24 1.0 0.6116
0.4536 1632.9 3600 1.6071 39.190 1.6350 1.0
Table 14.3.4a
14.3.5 Pressure/Head
bar kg/cm² lb/in² atm ft m mm Hg in Hg kPa
(psi) (water) (water)
1.0 1.0197 14.504 0.9869 33.455 10.197 750.06 29.530 100

0.9807 1.0 14.223 0.9878 32.808 10 735.56 28.959 98.07
0.0689 0.0703 1.0 0.0609 2.3067 0.7031 51.715 2.036 6.89
1.0133 1.0332 14.696 1.0 33.889 10.332 760.0 29.921 101.3
0.0299 0.0305 0.4335 0.0295 1.0 0.3048 22.420 0.8827 2.99
0.0981 0.10 1.422 0.0968 3.2808 1.0 73.356 2.896 9.81
13.3 x 10-4 0.0014 0.0193 13.2 x 10-4 0.0446 0.0136 1.0 0.0394 0.133
0.0339 0.0345 0.4912 0.0334 1.1329 0.3453 25.40 1,0 3.39
1.0 x 10-5 10.2 x 10-6 14.5 x 10-5 9.87 x 10-6 3.34 x 10-4 10.2 x 10-5 75.0 x 10-4 29.5 x 10-5 1.0
Table 14.3.5a
14.3.6 Force
Table 14.3.6a
kN kgf lbf
1.0 101.97 224.81

9.81 x 10-3 1.0 2.2046
44.5 x 10-4 0.4536 1.0
14.3.7 Torque
Table 14.3.7a
Nm kgfm lbft lbin
1.0 0.102 0.7376 8.8508

9.8067 1.0 7.2330 86.796
1.3558 0.1383 1.0 12.0
0.113 0.0115 0.0833 1.0

Technical Data
14.3.8 Power
W kgfm/s ft lbf/s hp kW
-3
1.0 0.102 0.7376 1.34 x 10 1000
9.8067 1.0 7.2330 0.0132 9806.7
1.3558 0.1383 1.0 1.82 x 10-3 1355.8
745.70 76.040 550.0 1.0 74.6 x 10-4
0.001 10.2 x 10-5 73.8 x 10-5 13.4 x 10-7 1.0
Table 14.3.8a
14.3.9 Density
Table 14.3.9a
kg/m3 g/cm3 lb/in3 lb/ft3
1 10-3 36.127 x 10-6 62.428 x 10-3

103 1 36.127 x 10-3 62.428
3
27.680 x 10 27.680 1 1.728 x 103
-3 -3
16.019 16.019 x 10 0.578 70 x 10 1

Technical Data
14.3.10 Viscosity Conversion Table

When SG = 1.0 When SG is
other than 1.0
Read Directly
Across Find Stoke, then
Find cSt, then
mutiply Stoke
x SG = Poise
mutiply cSt
x SG = cP
Saybolt Redwood
Universal Seconds Standard Ford Ford Zahn Zahn Zahn Zahn Zahn
cP Poise cSt Stoke SSU Engler #1 #3 #4 #1 #2 #3 #4 #5
1 0.01 1 0.01 31 54 29
2 0.02 2 0.02 34 57 32
4 0.04 4 0.04 38 61 36
7 0.07 7 0.07 47 75 44 8
10 0.10 10 0.10 60 94 52 9 5 30 16
15 0.15 15 0.15 80 125 63 10 8 34 17
20 0.20 20 0.20 100 170 86 12 10 37 18
25 0.25 25 0.25 130 190 112 15 12 41 19
30 0.30 30 0.30 160 210 138 19 14 44 20
40 0.40 40 0.40 210 300 181 25 18 52 22
50 0.50 50 0.50 260 350 225 29 22 60 24
60 0.60 60 0.60 320 450 270 33 25 68 27
70 0.70 70 0.70 370 525 314 36 28 72 30
80 0.80 80 0.80 430 600 364 41 31 81 34
90 0.90 90 0.90 480 875 405 45 32 88 37 10
100 1.0 100 1.0 530 750 445 50 34 41 12 10
120 1.2 120 1.2 580 900 492 58 41 49 14 11
140 1.4 140 1.4 690 1050 585 66 45 58 16 13
160 1.6 160 1.6 790 1200 670 72 50 66 18 14
180 1.8 180 1.8 900 1350 762 81 54 74 20 16
200 2.0 200 2.0 1000 1500 817 90 58 82 23 17 10
220 2.2 220 2.2 1100 1650 933 98 62 88 25 18 11
240 2.4 240 2.4 1200 1800 1020 106 65 27 20 12
260 2.6 260 2.6 1280 1950 1085 115 68 30 21 13
280 2.8 280 2.8 1380 2100 1170 122 70 32 22 14
300 3.0 300 3.0 1475 2250 1250 130 74 34 24 15
320 3.2 320 3.2 1530 2400 1295 136 89 36 25 16
340 3.4 340 3.4 1630 2550 1380 142 95 39 26 17
360 3.6 360 3.6 1730 2700 1465 150 100 41 27 18
380 3.8 380 3.8 1850 2850 1570 160 106 43 29 19
400 4.0 400 4.0 1950 3000 1650 170 112 46 30 20
420 4.2 420 4.2 2050 3150 1740 180 118 48 32 21
440 4.4 440 4.4 2160 3300 1830 188 124 50 33 22
460 4.6 460 4.6 2270 3450 1925 200 130 52 34 23
480 4.8 480 4.8 2380 3600 2020 210 137 54 36 24
500 5.0 500 5.0 2480 3750 2100 218 143 58 38 25
550 5.5 550 5.5 2660 4125 2255 230 153 64 40 27
600 6.0 600 6.0 2900 4500 2460 250 170 68 45 30
700 7.0 700 7.0 3380 5250 2860 295 194 76 51 35
800 8.0 800 8.0 3880 6000 3290 340 223 57 40
900 9.0 900 9.0 4300 8750 3640 365 247 63 45
1000 10 1000 10 4600 7500 3900 390 264 69 49

Technical Data
When SG = 1.0 When SG is

other than 1.0
Read Directly
Find Stoke, then

Across
Find cSt, then
mutiply Stoke
x SG = Poise
mutiply cSt
x SG = cP
Saybolt Redwood
Universal Seconds Standard Ford Ford Zahn Zahn Zahn Zahn Zahn
cP Poise cSt Stoke SSU Engler #1 #3 #4 #1 #2 #3 #4 #5
1100 11 1100 11 5200 8250 4410 445 299 77 55
1200 12 1200 12 5620 9000 4680 480 323 59
1300 13 1300 13 6100 9750 5160 520 350 64
1400 14 1400 14 6480 10350 5490 550 372 70
1500 15 1500 15 7000 11100 5940 595 400 75
1600 16 1600 16 7500 11850 6350 635 430 80
1700 17 1700 17 8000 12600 6780 680 460 85
1800 18 1800 18 8500 13300 7200 720 490 91
1900 19 1900 19 9000 13900 7620 760 520 96
2000 20 2000 20 9400 14600 7950 800 540
2100 21 2100 21 9850 15300 8350 835 565
2200 22 2200 22 10300 16100 8730 875 592
2300 23 2300 23 10750 16800 9110 910 617
2400 24 2400 24 11200 17500 9500 950 645
2500 25 2500 25 11600 18250 9830 985 676
3000 30 3000 30 14500 21800 12300 1230 833
3500 35 3500 35 16500 25200 14000 1400 950
4000 40 4000 40 18500 28800 15650 1570 1060
4500 45 4500 45 21000 32400 17800 1175
5000 50 5000 50 23500 36000 19900 1350
5500 55 5500 55 26000 39600 1495
6000 60 6000 60 28000 43100 1605
6500 65 6500 65 30000 46000 1720
7000 70 7000 70 32500 49600 1870
7500 75 7500 75 35000 53200 2010
8000 80 8000 80 37000 56800 2120
8500 85 8500 85 39500 60300 2270
9000 90 9000 90 41080 63900 2350
9500 95 9500 95 43000 67400 2470
10000 100 10000 100 46500 71000 2670
15000 150 15000 150 69400 106000
20000 200 20000 200 92500 140000
30000 300 30000 300 138500 210000
40000 400 40000 400 185000 276000
50000 500 50000 500 231000 345000
60000 600 60000 600 277500 414000
70000 700 70000 700 323500 484000
80000 800 80000 800 370000 550000
90000 900 90000 900 415500 620000
100000 1000 100000 1000 462000 689000
125000 1250 125000 1250 578000 850000
150000 1500 150000 1500 694000
175000 1750 175000 1750 810000
200000 2000 200000 2000 925000
Table 14.3.10a

Technical Data
14.3.11 Temperature Conversion Table

minus 459.4 - 0 0 - 49 50 - 100 100 - 490 500 - 1000
°C to °F °C to °F °C to °F °C to °F °C to °F
-273 -459 -17.8 0 32 10.0 50 122.0 38 100 212 260 500 932
-268 -450 -17.2 1 33.8 10.6 51 123.8 43 110 230 266 510 950
-262 -440 -16.7 2 35.6 11.1 52 125.6 49 120 248 271 520 968
-257 -430 -16.1 3 37.4 11.7 53 127.4 54 130 266 277 530 986
-251 -420 -15.6 4 39.2 12.2 54 129.2 60 140 284 282 540 1004
-246 -410 -15.0 5 41.0 12.8 55 131.0 66 150 302 288 550 1022
-240 -400 -14.4 6 42.8 13.3 56 132.8 71 160 320 293 560 1040
-234 -390 -13.9 7 44.6 13.9 57 134.6 77 170 338 299 570 1058
-229 -380 -13.3 8 46.4 14.4 58 136.4 82 180 356 304 580 1076
-223 -370 -12.8 9 48.2 15.0 59 138.2 88 190 374 310 590 1094
-218 -360 -12.2 10 50.0 15.6 60 140.0 93 200 392 316 600 1112
-212 -350 -11.7 11 51.8 16.1 61 141.8 99 210 410 321 610 1130
-207 -340 -11.1 12 53.6 16.7 62 143.6 100 212 414 327 620 1148
-201 -330 -10.6 13 55.4 17.2 63 145.4 104 220 428 332 630 1166
-196 -320 -10.0 14 57.2 17.8 64 147.2 110 230 446 338 640 1184
-190 -310 -9.4 15 59.0 18.3 65 149.0 116 240 464 343 650 1202
-184 -300 -8.9 16 60.8 18.9 66 150.8 121 250 482 349 660 1220
-179 -290 -8.3 17 62.6 19.4 67 152.6 127 260 500 354 670 1238
-173 -280 -7.8 18 64.4 20.0 68 154.4 132 270 518 360 680 1256
-169 -273 -459.4 -7.2 19 66.2 20.6 69 156.2 138 280 536 366 690 1274
-168 -270 -454 -6.7 20 68.0 21.1 70 158.0 143 290 554 371 700 1292
-162 -260 -436 -6.1 21 69.8 21.7 71 159.8 149 300 572 377 710 1310
-157 -250 -418 -5.6 22 71.6 22.2 72 161.6 154 310 590 382 720 1328
-151 -240 -400 -5.0 23 73.4 22.8 73 163.4 160 320 608 388 730 1346
-146 -230 -382 -4.4 24 75.2 23.3 74 165.2 166 330 626 393 740 1364
-140 -220 -364 -3.9 25 77.0 23.9 75 167.0 171 340 644 399 750 1382
-134 -210 -346 -3.3 26 78.8 24.4 76 168.8 177 350 662 404 760 1400
-129 -200 -328 -2.8 27 80.6 25.0 77 170.6 182 360 680 410 770 1418
-123 -190 -310 -2.2 28 82.4 25.6 78 172.4 188 370 698 416 780 1436
-118 -180 -292 -1.7 29 84.2 26.1 79 174.2 193 380 716 421 790 1454
-112 -170 -274 -1.1 30 86.0 26,7 80 176.0 199 390 734 427 800 1472
-107 -160 -256 -0.6 31 87.8 27.2 81 177.8 204 400 752 432 810 1490
-101 -150 -238 0.0 32 89.6 27.8 82 179.6 210 410 770 438 820 1508
-96 -140 -220 0.6 33 91.4 28.3 83 181.4 216 420 788 443 830 1526
-90 -130 -202 1.1 34 93.2 28.9 84 183.2 221 430 806 449 840 1544
-84 -120 -184 1.7 35 95.0 29.4 85 185.0 227 440 824 454 850 1562
-79 -110 -166 2.2 36 96.8 30.0 86 186.8 232 450 842 460 860 1580
-73 -100 -148 2.8 37 98.6 30.6 87 188.6 238 460 860 466 870 1598
-68 -90 -130 3.3 38 100.4 31.1 88 190.4 243 470 878 471 880 1616
-62 -80 -112 3.9 39 102.2 31.7 89 192.2 249 480 896 477 890 1634
-57 -70 -94 4.4 40 104.0 32.2 90 194.0 254 490 914 482 900 1652
-51 -60 -76 5.0 41 105.8 32.8 91 195.8 488 910 1670
-46 -50 -58 5.6 42 107.6 33.3 92 197.6 493 920 1688
-40 -40 -40 6.1 43 109.4 33.9 93 199.4 499 930 1706
-34 -30 -22 6.7 44 111.2 34.4 94 201.2 504 940 1724
-29 -20 -4 7.2 45 113.0 35.0 95 203.0 510 950 1742
-23 -10 14 7.8 46 114.8 35.6 96 204.8 516 960 1760
-17.8 0 32 8.3 47 116.6 36.1 97 206.6 521 970 1778
8.9 48 118.4 36.7 98 208.4 527 980 1796
9.4 49 120.2 37.2 99 210.2 532 990 1814
37.8 100 212.0 538 1000 1832
Locate temperature in middle column. If in °C read the °F equivalent in the right hand column. If in °F read °C
equivalent in the left hand column. °C = ( °F - 32 ) x 0.5556 °F = ( °C x 1.8 ) + 32
Table 14.3.11a

Technical Data
14.4 Water Vapour Pressure Table

Table 14.4a
Temp. Density (r) Vapour pressure (Pvp)
(°C) (kg/m3) (kPa)
0 999.8 0.61
5 1000.0 0.87
10 999.7 1.23
15 999.1 1.71
20 998.2 2.33
25 997.1 3.40
30 995.7 4.25
35 994.1 5.62
40 992.2 7.38
45 990.2 9.60
50 988.0 12.3
55 985.7 15.7
60 983.2 19.9
65 980.6 25.1
70 977.8 31.2
75 974.9 38.6
80 971.8 47.5
85 968.6 57.9
90 965.3 70.1
95 961.9 84.7
100 958.4 101.3
Vapour pressure: 1 bar = 100 kPa = 105 N/m2

Technical Data
14.5 Pressure Drop Curve for 100 m ISO/DIN Tube
1 bar » 10 m (metre liquid column)
Fig. 14.5a Pressure Drop Curve

Technical Data
14.6 Velocity (m/s) in ISO and DIN Tubes at various Capacities
l/h
0 20000 40000 60000 80000 100000 120000 140000 160000 180000 200000
1 m3/h = 1000 l/h

Fig. 14.6a Connection between velocity
and capacity at different tube dimensions

Technical Data
14.7 Equivalent Tube Length Table

14.7.1 ISO Tube Metric
Equipment for ISO tube Equivalent tube length in metres per unit
(for water at 2 m/s) 25 mm 38 mm 51 mm 63.5 mm 76 mm 101.6 mm
Seat valves
1. SRC, SMO 7 6 12 21 30
2. 5 4 6 14 19
3. 4 10 12 15 29
4. 3 4 7 12 26
5. 5 14 27 32 50
6. 5 10 21 22 39
1. SRC-LS 7 12 11 8
2. 3 8 7 6
3. 7 8 9 14
4. 5 4 6 11
5. 8 13 13 19
6. 7 10 11 17
Aseptic seat valves
1. ARC, AMO 7 13 28 43 55
2. 5 9 21 27 36
3. 4 10 20 32 55
4. 4 8 15 29 39
5. 6 18 37 61 88
6. 5 15 28 50 75
1. ARC-SB 8 15 20
2. 8 15 20
3. 6 10 18
4. 8 17 44
Other valves
Non-return valve LKC-2 7 10 12 21 20 26
Butterfly valve LKB 1 1 1 1 2 2
1. Koltek MH 1 2 3 5 6 7
2. 1 2 4 6 9 10

Technical Data
Equipment for ISO tube Equivalent tube length in metres per unit
(for water at 2 m/s) 25 mm 38 mm 51 mm 63.5 mm 76 mm 101.6 mm
Mixproof valves
1. Unique * 14 14 27 25 26
2. 14 14 27 25 26
3. 5 4 6 5 4
4. 6 5 7 7 5
1. SMP-SC 14 17 32 55
2. 14 16 25 41
3. 4 4 5 5
4. 4 5 5 14
1. SMP-SC, 3-body 8 14 27 45
2. 8 16 29 52
1. SMP-BC 3 3 4 3 6
2. 3 6 11 8 18
3. 3 5 7 7 11
4. 7 11 13 15 32
5. 6 10 13 14 31
6. 9 12 34 25 101
7. 6 12 34 23 101
1. SMP-BCA 2 3 4 3 6
2. 5 10 18 29 84
3. 3 9 16 29 81
4. 6 18 30 41 104
5. 5 12 20 27 75
6. 5 14 41 41 152
7. 6 14 34 38 146
1. SMP-TO 5 6
2. 8 23
3. 5 24
Tubes and fittings
Bend 90 deg. 0.3 1 1 1 1 2
Bend 45 deg. 0.2 0.4 1 1 1 1
Tee (out through side port) 1 2 3 4 5 7
Tee (in through side port) 1 2 2 3 4 5
* Pressure drop/equivalent tube length is for unbalanced upper plug and balanced lower plug.
Table 14.7.1a
For other combinations use the CAS Unique configuration tool.

Technical Data
14.7.2 ISO Tube Feet

Equipment for ISO tube Equivalent tube length in feet per unit
(for water at 6 ft/s) 1 in 1.5 in 2 in 2.5 in 3 in 4 in
Seat valves
1. SRC, SMO 23 20 39 69 98
2. 16 13 20 46 62
3. 13 33 39 49 95
4. 10 13 23 39 85
5. 16 46 89 105 164
6. 16 33 69 72 128
1. SRC-LS 23 39 36 26
2. 10 26 23 20
3. 23 26 30 46
4. 16 13 20 36
5. 26 43 43 62
6. 23 33 36 56
Seat valves
1. ARC, AMO 23 43 92 141 180
2. 16 30 69 89 118
3. 13 33 66 105 180
4. 13 26 49 95 128
5. 20 59 121 200 289
6. 16 49 92 164 246
1. ARC-SB 26 49 66
2. 26 49 66
3. 20 33 59
4. 26 56 144
Other valves
Butterfly valve LKB 3 3 3 3 7 7
1. Koltek MH 3 7 10 16 20 23
2. 3 7 13 20 30 33

Technical Data
Equipment for ISO tube Equivalent tube length in feet per unit
(for water at 6 ft/s) 1 in 1.5 in 2 in 2.5 in 3 in 4 in
Mixproof valves
1. Unique * 46 46 89 82 85
2. 46 46 89 82 85
3. 16 13 20 16 13
4. 20 16 23 23 16
1. SMP-SC 46 56 105 180
2. 46 52 82 135
3. 13 13 16 16
4. 13 16 16 46
1. SMP-SC, 3-body 26 46 89 148
2. 26 52 95 171
1. SMP-BC 10 10 13 10 20
2. 10 20 36 26 59
3. 10 16 23 23 36
4. 23 36 43 49 105
5. 20 33 43 46 102
6. 30 39 112 82 331
7. 20 39 112 75 331
1. SMP-BCA 7 10 13 10 20
2. 16 33 59 95 276
3. 10 30 52 95 266
4. 20 59 98 135 341
5. 16 39 66 89 246
6. 16 46 135 135 499
7. 20 46 112 125 479
1. SMP-TO 16 20
2. 26 75
3. 16 79
Tubes and fittings
Bend 90 deg. 1 3 3 3 3 7
Bend 45 deg. 1 1 3 3 3 3
* Pressure drop/equivalent tube length is for unbalanced upper plug and balanced lower plug. Table 14.7.2a

Technical Data
14.7.3 DIN Tube Metric

Equipment for DIN tube Equivalent tube length in metres per unit
(for water at 2 m/s) DN25 DN40 DN50 DN65 DN80 DN100 DN125 DN150
Seat valves
1. SRC, SMO 8 7 15 28 33 18 44
2. 6 6 9 21 23 22 72
3. 4 11 18 27 33 29 72
4. 4 6 12 23 28 27 69
5. 6 18 44 54 57 49 150
6. 6 15 34 36 43 38 89
1. SRC-LS 9 19 21 9
2. 4 10 14 7
3. 9 13 18 17
4. 8 7 12 13
5. 11 19 24 22
6. 10 16 22 18
Aseptic seat valves
1. ARC, AMO 8 15 42 64 64
2. 6 11 28 44 40
3. 5 13 26 46 57
4. 5 9 22 44 43
5. 7 20 54 98 94
6. 6 17 40 77 84
1. ARC-SB 10 21 34
2. 10 21 34
3. 6 11 24
4. 9 21 64
Other valves
Butterfly valve LKB 2 1 1 2 2 2 2 1
1. Koltek MH 2 2 5 9 10 8
2. 2 2 5 9 14 13

Technical Data
Equipment for DIN tube Equivalent tube length in metres per unit
(for water at 2 m/s) DN25 DN40 DN50 DN65 DN80 DN100 DN125 DN150
Mixproof valves
1. Unique * 14 14 27 25 26
2. 14 14 27 25 26
3. 5 4 6 5 4
4. 6 5 7 7 5
1. SMP-SC 15 24 54 64 49 89
2. 14 22 41 50 53 133
3. 4 6 6 6 7 22
4. 4 6 6 15 7 22
1. SMP-SC, 3-body 9 22 44 54
2. 9 25 54 64
1. SMP-BC 3 4 5 5 7 4 8
2. 4 7 13 15 21 38 78
3. 4 6 11 12 20 31 61
4. 9 17 22 24 40
5. 7 13 22 23 37
6. 10 15 52 44 114
7. 9 15 52 44 114
1. SMP-BCA 3 4 5 5 6
2. 6 13 32 51 97
3. 3 12 25 49 94
4. 9 24 46 72 124
5. 6 15 30 46 84
6. 8 20 62 67 174
7. 9 21 54 64 167
1. SMP-TO 7 8
2. 11 28
3. 8 30
Tubes and fittings
Bend 90 deg. 0.3 1 1 1 1 2
Bend 45 deg. 0.2 0.4 1 1 1 1

Technical Data
14.7.4 DIN Tube Feet

Equipment for DIN tube Equivalent tube length in feet per unit
(for water at 6 ft/s) 1 in 1.5 in 2 in 2.5 in 3 in 4 in 5 in 6 in
Seat valves
1. SRC, SMO 26 23 49 92 108 59 144
2. 20 20 30 69 75 72 236
3. 13 36 59 89 108 95 236
4. 13 20 39 75 92 89 226
5. 20 59 144 177 187 161 492
6. 20 49 112 118 141 125 292
1. SRC-LS 30 62 69 30
2. 13 33 46 23
3. 30 43 59 56
4. 26 23 39 43
5. 36 62 79 72
6. 33 52 72 59
Aseptic seat valves
1. ARC, AMO 26 49 138 210 210
2. 20 36 92 144 131
3. 16 43 85 151 187
4. 16 30 72 144 141
5. 30 66 177 322 308
6. 20 56 131 253 276
1. ARC-SB 33 69 112
2. 33 69 112
3. 20 36 79
4. 30 69 210
Other valves
Butterfly valve LKB 7 3 3 7 7 7 7 3
1. Koltek MH 7 7 16 30 33 26
2. 7 7 16 30 46 43

Technical Data
Equipment for DIN tube Equivalent tube length in feet per unit
(for water at 6 ft/s) 1 in 1.5 in 2 in 2.5 in 3 in 4 in 5 in 6 in
Mixproof valves
1. Unique * 46 46 89 82 85
2. 46 46 89 82 85
3. 16 13 20 16 13
4. 20 16 23 23 16
1. SMP-SC 49 79 177 210 161 292
2. 46 72 135 164 174 436
3. 13 20 20 20 23 72
4. 13 20 20 49 23 72
1. SMP-SC, 3-body 30 72 144 177
2. 30 82 177 210
1. SMP-BC 10 13 16 16 23 13 26
2. 13 23 43 49 69 125 256
3. 13 20 36 39 66 102 200
4. 30 56 72 79 131
5. 23 43 72 75 121
6. 33 49 171 144 374
7. 30 49 171 144 374
1. SMP-BCA 10 13 16 16 20
2. 20 43 105 167 318
3. 10 39 82 161 308
4. 30 79 151 236 407
5. 20 49 98 151 276
6. 26 66 203 220 571
7. 30 69 177 210 548
1. SMP-TO 23 26
2. 36 92
3. 26 98
Tubes and fittings
Bend 90 deg. 1 3 3 3 3 7
Bend 45 deg. 1 1 3 3 3 3

Technical Data
14.8 Moody Diagram
Fig. 14.8a Moody diagram for fD (after Miller)

Technical Data
14.9 Initial Suction Line Sizing

Flow rate - m3/h
100
Fig. 14.9a Initial suction line sizing Viscosity - cSt

Technical Data
14.10 Elastomer Compatibility Guide

Listed below are fluids commonly pumped.
The elastomer compatibilty is for guidance purposes only as this

maybe affected by temperature.
The fluid viscous behaviour type shown relates to general terms

- in some instances Pseudoplastic fluids can have Thixotropic
tendencies.
(†) - Fluid can become Dilatant at high concentration and high

shear rate.
(‡) - If low concentration, this can be Newtonian.
Name of Fluid Pumped Elastomer Material Viscous Behaviour Type

NBR EPDM FPM PTFE
ACETIC ACID ü ü Newtonian

ACETONE ü ü Newtonian
ADHESIVE - SOLVENT BASED ü Pseudoplastic
ADHESIVE - WATER BASED ü ü Pseudoplastic
ALUM SLUDGE ü ü ü ü Pseudoplastic
AMMONIUM HYDROXIDE ü ü Newtonian
ANIMAL FAT ü ü Newtonian
BABY BATH ü ü Pseudoplastic
BABY LOTION ü ü Pseudoplastic
BABY OIL ü ü Newtonian
BATH FOAM ü ü Pseudoplastic
BATTER ü ü ü Pseudoplastic
BEER ü ü ü Newtonian
BENTONITE SUSPENSION ü ü ü ü Pseudoplastic (†)
BISCUIT CREAM ü ü Pseudoplastic
BISULPHITE ü ü ü ü Newtonian
BITUMEN ü ü ü Pseudoplastic
BLACK LIQUOR ü ü Newtonian
BLEACH ü ü ü Newtonian
BLOOD ü ü ü Newtonian
BODY LOTION ü ü Pseudoplastic
BODY SCRUB ü ü Pseudoplastic
BRINE ü ü ü ü Newtonian
BUTTER ü ü ü Pseudoplastic
CALCIUM CARBONATE SLURRY ü ü ü ü Pseudoplastic
CARAMEL - COLOURING ü ü ü Newtonian
CARAMEL - TOFFEE ü ü ü Pseudoplastic
CASTOR OIL ü ü ü Newtonian
CELLULOSE ACETATE DOPE ü Pseudoplastic
CELLULOSE SUSPENSION ü ü ü ü Pseudoplastic
CERAMIC SLIP ü ü ü ü Pseudoplastic (†)

Technical Data

NBR EPDM FPM PTFE
CHEESE ü ü ü Pseudoplastic
CHEWING GUM ü Pseudoplastic
CHINA CLAY SLURRY ü ü ü ü Pseudoplastic (†)
CHOCOLATE ü ü Pseudoplastic
CHROMIC ACID ü ü Newtonian
CHUTNEY ü ü ü Pseudoplastic
CITRIC ACID ü ü ü ü Newtonian
COAL TAR ü ü Newtonian
COCOA BUTTER ü ü Newtonian
COCOA LIQUOR ü ü Pseudoplastic
COCONUT CREAM ü ü Pseudoplastic
COLLAGEN GEL ü ü ü Pseudoplastic
CONDENSED MILK ü ü ü Pseudoplastic
COPPER SULPHATE ü ü ü Newtonian
CORN STEEP LIQUOR ü ü ü Newtonian
CORN SYRUP ü ü ü ü Newtonian
COSMETIC CREAM ü ü Pseudoplastic
COUGH SYRUP ü ü ü Pseudoplastic
CRUDE OIL ü ü Pseudoplastic
CUSTARD ü ü ü Pseudoplastic
DAIRY CREAM ü ü ü Pseudoplastic
DETERGENT - AMPHOTERIC ü ü Newtonian
DETERGENT - ANIONIC ü ü ü ü Pseudoplastic (‡)
DETERGENT - CATIONIC ü ü Newtonian
DETERGENT - NONIONIC ü ü ü Newtonian
DIESEL OIL ü ü ü Newtonian
DODECYL BENZENE SULPHONIC ACID ü ü Newtonian
DRILLING MUD ü ü ü ü Pseudoplastic
DYE ü ü ü Newtonian
EGG ü ü ü Pseudoplastic
ENZYME SOLUTION ü ü Newtonian
ETHANOL ü ü ü Newtonian
ETHYLENE GLYCOL ü ü ü ü Newtonian
FABRIC CONDITIONER ü ü Pseudoplastic
FATS ü ü Newtonian
FATTY ACID ü ü Newtonian
FERRIC CHLORIDE ü ü ü ü Newtonian
FERTILISER ü ü ü ü Pseudoplastic
FILTER AID ü ü ü ü Pseudoplastic
FININGS ü ü ü Pseudoplastic
FIRE FIGHTING FOAM ü ü Pseudoplastic
FISH OIL ü ü Newtonian
FONDANT ü ü ü Pseudoplastic
FORMIC ACID ü ü Newtonian
FROMAGE FRAIS ü ü ü Pseudoplastic
FRUCTOSE ü ü ü Newtonian
FRUIT JUICE CONCENTRATE ü ü ü Pseudoplastic
FRUIT PUREE ü ü ü Pseudoplastic

Technical Data

NBR EPDM FPM PTFE
FUDGE ü ü ü Pseudoplastic
GELATINE ü ü ü Pseudoplastic
GLUCOSE ü ü ü Newtonian
GLYCERINE ü ü ü ü Newtonian
GREASE ü ü ü Pseudoplastic
GYPSUM SLURRY ü ü ü ü Pseudoplastic
HAIR CONDITIONER ü ü Pseudoplastic
HAIR GEL ü ü Pseudoplastic
HAND CLEANSER ü ü Pseudoplastic
HONEY ü ü ü Pseudoplastic
HYDROCHLORIC ACID ü ü Newtonian
HYDROGEN PEROXIDE ü ü Newtonian
ICE CREAM MIX ü ü ü Pseudoplastic
INK - PRINTING ü ü Pseudoplastic
INK - WATER BASED ü ü ü Newtonian
ISOBUTYL ALCOHOL ü ü ü Newtonian
ISOCYANATE ü Newtonian
ISOPROPANOL ü ü ü Newtonian
JAM ü ü ü Pseudoplastic
KEROSENE ü ü ü Newtonian
LACTIC ACID ü ü Newtonian
LACTOSE ü ü ü Newtonian
LANOLIN ü ü Newtonian
LATEX ü ü Pseudoplastic
LECITHIN ü ü Newtonian
LIPSTICK ü ü Pseudoplastic
LIQUORICE ü ü Pseudoplastic
MAGMA ü ü ü Pseudoplastic
MAIZE STARCH SLURRY ü ü ü ü Pseudoplastic
MALT EXTRACT ü ü ü Pseudoplastic
MANGANESE NITRATE ü ü Newtonian
MASCARA ü ü Pseudoplastic
MASHED POTATO ü ü ü Pseudoplastic
MASSECUITE ü ü ü Pseudoplastic
MAYONNAISE ü Pseudoplastic
MEAT PASTE ü ü ü Pseudoplastic
METHANOL ü ü ü Newtonian
METHYL ETHYL KETONE SOLVENT ü ü Newtonian
METHYLATED SPIRIT ü ü ü Newtonian
METHYLENE CHLORIDE ü ü Newtonian
MILK ü ü ü Newtonian
MINCEMEAT ü ü ü Pseudoplastic
MINERAL OIL ü ü ü Newtonian
MOLASSES ü ü ü Newtonian
MUSTARD ü ü ü Pseudoplastic
NEAT SOAP ü ü Pseudoplastic
NITRIC ACID ü ü Newtonian
PAINTS - SOLVENT BASED ü Pseudoplastic

Technical Data

NBR EPDM FPM PTFE
PAINTS - WATER BASED ü ü ü ü Pseudoplastic

PAPER COATING - CLAY ü ü Pseudoplastic (†)
PAPER COATING - PIGMENT ü ü ü ü Pseudoplastic (†)
PAPER COATING - STARCH ü ü ü ü Pseudoplastic
PAPER PULP ü ü ü ü Pseudoplastic
PEANUT BUTTER ü ü Pseudoplastic
PERACETIC ACID ü Newtonian
PETFOOD ü ü ü Pseudoplastic
PETROLEUM ü ü ü Newtonian
PHOSPHORIC ACID ü ü Newtonian
PHOTOGRAPHIC EMULSION ü ü ü Pseudoplastic
PLASTISOL ü ü Newtonian
POLYETHYLENE GLYCOL ü ü ü Newtonian
POLYVINYL ALCOHOL ü ü ü Pseudoplastic
POTASSIUM HYDROXIDE ü ü Newtonian
PROPIONIC ACID ü Newtonian
PROPYLENE GLYCOL ü ü ü ü Newtonian
QUARG ü ü ü Pseudoplastic
RESIN ü ü Newtonian
RUBBER SOLUTION ü Pseudoplastic
SAUCE - CONFECTIONERY ü ü Pseudoplastic
SAUCE - VEGETABLE ü ü ü Pseudoplastic
SAUSAGE MEAT ü ü ü Pseudoplastic
SEWAGE SLUDGE ü ü ü ü Pseudoplastic
SHAMPOO ü ü Pseudoplastic
SHAVING CREAM ü ü Pseudoplastic
SILICONE OIL ü ü ü ü Newtonian
SODIUM HYDROXIDE ü ü Newtonian
SODIUM SILICATE ü ü ü Newtonian
SORBIC ACID ü Newtonian
SORBITOL ü ü ü ü Newtonian
STARCH ü ü ü Pseudoplastic
SUGAR PULP - BEET ü ü ü Pseudoplastic
SUGAR PULP - CANE ü ü ü Pseudoplastic
SUGAR SYRUP ü ü ü Newtonian
SULPHURIC ACID ü ü Newtonian
TALL OIL ü ü Newtonian
TALLOW ü ü Newtonian
TITANIUM DIOXIDE ü ü ü ü Pseudoplastic (†)
TOBACCO FLAVOURING ü Newtonian
TOLUENE ü ü Newtonian
TOMATO KETCHUP ü ü ü Pseudoplastic
TOMATO PUREE ü ü ü Pseudoplastic
TOOTHPASTE ü ü Pseudoplastic
TRUB ü ü ü ü Pseudoplastic
UREA ü ü ü Newtonian
VARNISH ü Newtonian
VASELINE ü ü ü Pseudoplastic

Technical Data

NBR EPDM FPM PTFE
VEGETABLE GUM ü ü ü Pseudoplastic

VEGETABLE OIL ü ü Newtonian
VITAMIN SOLUTION ü ü ü Newtonian
WATER ü ü ü ü Newtonian
WAX ü ü Newtonian
WHEY ü ü ü Newtonian
WHITE SPIRIT ü ü Newtonian
WINE ü ü ü Newtonian
WORT ü ü ü Newtonian
XYLENE ü ü Newtonian
YEAST ü ü ü Pseudoplastic
YOGHURT ü ü ü Pseudoplastic
ZEOLITE SLURRY ü ü ü ü Pseudoplastic (†)
ZIRCONIA SLURRY ü ü ü ü Pseudoplastic (†)
Table 14.10a Elastomer compatibility guide

Technical Data
14.11 Changing Motor Name Plates

Manufacturer Frame Output Frequency Supply Voltage Motor Rated Speed Power Rated
Size Power kW Hz V Nameplate rev/min Factor Current A
2-pole motors
ABB 71 C 0.55 50 220-240D/380-420Y Standard 2870 0.81 2.3/1.3

0.55 50 200D New 2810 0.89 2.4
0.55 60 380-480Y Standard 3460 0.82 1.2
0.55 60 200D New 3370 0.91 2.3
0.55 60 220D New 3420 0.88 2.1
ABB 80 A 0.75 50 220-240D/380-420Y Standard 2860 0.82 3.1/1.8
0.75 50 200D New 2810 0.89 3.3
0.75 60 440-480Y Standard 3490 0.78 1.5
0.75 60 200D New 3380 0.90 3.1
0.75 60 220D New 3430 0.88 2.8
0.75 60 400Y New 3450 0.86 1.6
0.75 60 380Y New 3420 0.88 1.6
ABB 80 C 1.1 50 220-240D/380-420Y Standard 2870 0.85 4.3/2.5
1.1 50 200D New 2840 0.90 4.5
1.1 60 440-480Y Standard 3500 0.83 2.0
1.1 60 200D New 3400 0.91 4.3
1.1 60 220D New 3450 0.90 3.9
1.1 60 400Y New 3460 0.89 2.2
1.1 60 380Y New 3450 0.90 2.3
ABB 90 L 1.5 50 220-240D/380-420Y Standard 2920 0.85 5.4/3.2
1.5 50 200D New 2880 0.89 6.0
1.75 60 440-480Y Standard 3510 0.85 3.1
1.5 60 200D New 3460 0.91 5.9
1.6 60 220D New 3490 0.89 5.4
1.6 60 400Y New 3500 0.88 3.0
1.6 60 380Y New 3490 0.89 3.1
ABB 90 LB 2.2 50 220-240D/380-420Y Standard 2900 0.85 8.1/4.7
2.2 50 200D New 2860 0.90 8.7
2.5 60 440-480Y Standard 3500 0.86 4.4
2.1 60 200D New 3430 0.91 8.3
2.3 60 220D New 3470 0.90 7.5
2.3 60 400Y New 3470 0.90 4.5
2.3 60 380Y New 3450 0.91 4.8
ABB 100 LB 3.0 50 220-240D/380-420Y Standard 2920 0.88 9.9/5.7
3.0 50 200D New 2890 0.91 11.0
3.5 60 440-480Y Standard 3520 0.88 5.7
3.0 60 200D New 3470 0.92 10.9
3.2 60 220D New 3490 0.91 10.5
3.2 60 400Y New 3500 0.91 5.8
3.2 60 380Y New 3490 0.91 6.1
3.0 50 380-420D/660-690Y Standard 2920 0.87 5.7/3.3
3.5 60 440-480D Standard 3520 0.88 5.7
3.2 60 400D New 3500 0.91 5.8
3.2 60 380D New 3490 0.91 6.1

Technical Data
2-pole motors
ABB 112 M 4.0 50 220-240D/380-420Y Standard 2850 0.91 13.5/7.8

3.7 50 200D New 2790 0.92 14.5
4.6 60 440-480Y Standard 3450 0.91 7.7
3.4 60 200D New 3360 0.92 13.1
3.8 60 220D New 3390 0.91 13.3
4.0 60 400Y New 3400 0.91 7.4
3.8 60 380Y New 3390 0.91 7.7
4.0 50 380-420D/660-690Y Standard 2850 0.91 7.8/4.5
4.6 60 440-480D Standard 3450 0.91 7.7
4.0 60 400D New 3400 0.91 7.4
3.8 60 380D New 3390 0.91 7.7
ABB 132 SA 5.5 50 220-240D/380-420Y Standard 2855 0.88 18.9/10.9
5.4 50 200D New 2790 0.90 21.0
6.4 60 440-480Y Standard 3455 0.88 10.9
5.4 60 200D New 3345 0.91 21.0
5.4 60 220D New 3395 0.89 18.8
5.7 60 400Y New 3380 0.89 10.9
5.4 60 380Y New 3370 0.89 10.9
5.5 50 380-420D/660-690Y Standard 2855 0.88 10.9/6.3
6.4 60 440-480D Standard 3455 0.88 10.9
5.7 60 400D New 3380 0.89 10.9
5.4 60 380D New 3370 0.89 10.9
ABB 132 SB 7.5 50 220-240D/380-420Y Standard 2855 0.90 25.5/14.7
6.6 50 200D New 2825 0.91 25.0
8.6 60 440-480Y Standard 3455 0.90 14.4
7.0 60 200D New 3365 0.92 26.0
7.4 60 220D New 3405 0.91 25.0
7.8 60 400Y New 3415 0.91 14.4
7.4 60 380Y New 3405 0.91 14.4
7.5 50 380-420D/660-690Y Standard 2855 0.90 14.7/8.5
8.6 60 440-480D Standard 3455 0.90 14.4
7.8 60 400D New 3415 0.91 14.4
7.4 60 380D New 3405 0.91 14.4
ABB 160 MA 11.0 50 230D/400Y Standard 2930 0.88 34.5/20.0
11.0 50 200D New 2900 0.89 40.0
12.5 60 440Y Standard 3515 0.89 20.0
11.0 60 200D New 3475 0.89 40.0
12.2 60 220D New 3485 0.89 40.0
12.5 60 400Y New 3500 0.89 22.0
12.2 60 380Y New 3485 0.89 23.0
11.0 50 400D/690Y Standard 2930 0.88 20.0/11.5
12.5 60 440D Standard 3515 0.89 20.0
12.5 60 400D New 3500 0.89 22.0
12.2 60 380D New 3485 0.89 23.0

Technical Data
2-pole motors
ABB 160M 15.0 50 230D/400Y Standard 2920 0.9 46.0/26.5

14.5 50 200D New 2890 0.9 53.0
17.0 60 440Y Standard 3505 0.9 27.5
14.0 60 200D New 3470 0.9 51.0
15.7 60 220D New 3485 0.89 52.0
16.5 60 400Y New 3500 0.89 30.0
15.7 60 380Y New 3485 0.89 30.0
15.0 50 400D/690Y Standard 2920 0.9 26.5/15.3
17.0 60 440D Standard 3505 0.9 27.5
16.5 60 400D New 3500 0.89 30.0
15.7 60 380D New 3485 0.89 30.0
ABB 160 L 18.5 50 230D/400Y Standard 2920 0.91 55.0/32.0
17.2 50 200D New 2895 0.91 60.0
21.0 60 440Y Standard 3510 0.91 33.5
16.7 60 200D New 3500 0.91 59.0
18.5 60 220D New 3490 0.91 59.0
19.4 60 400Y New 3500 0.91 34.0
18.5 60 380Y New 3490 0.91 34.0
18.5 50 400D/690Y Standard 2920 0.91 32.0/18.5
21.0 60 440D Standard 3510 0.91 33.5
19.4 60 400D New 3500 0.91 34.0
18.5 60 380D New 3490 0.91 34.0
ABB 180 M 22.0 50 230D/400Y Standard 2930 0.89 67.0/38.5
22.0 50 200D New 2920 0.90 77.0
25.0 60 440Y Standard 3530 0.90 40.5
22.0 60 200D New 3505 0.91 76.0
25.0 60 220D New 3510 0.89 80.0
25.0 60 400Y New 3520 0.88 44.0
25.0 60 380Y New 3510 0.89 46.0
22.0 50 400D/690Y Standard 2930 0.89 38.5/22.0
25.0 60 440D Standard 3530 0.90 40.5
25.0 60 400D New 3520 0.88 44.0
25.0 60 380D New 3510 0.89 46.0
4-pole motors
ABB 90 L-4 1.5 50 220-240D/380-420Y Standard 1440 0.74 6.2/3.6

1.5 50 200D New 1380 0.86 6.3
1.75 60 440-480Y Standard 1730 0.76 3.5
1.5 60 200D New 1660 0.87 6.2
1.6 60 220D New 1680 0.86 6.1
1.75 60 400Y New 1680 0.86 3.6
1.75 60 380Y New 1660 0.87 3.8

Technical Data
4-pole motors
ABB 132 S-4 5.5 50 220-240D/380-420Y Standard 1440 0.83 19.9/11.5

5.3 50 200D New 1430 0.86 21.1
6.4 60 440-480Y Standard 1750 0.83 11.5
5.5 60 200D New 1700 0.86 22.0
6.0 60 220D New 1730 0.86 21.5
6.3 60 400Y New 1735 0.86 12.4
6.0 60 380Y New 1730 0.86 12.4
5.5 50 380-420D/660-690Y Standard 1450 0.83 11.5/6.6
6.4 60 440-480D Standard 1750 0.83 11.5
6.3 60 400D New 1735 0.86 12.4
6.0 60 380D New 1730 0.86 12.4
ABB 132 M-4 7.5 50 220-240D/380-420Y Standard 1450 0.83 27.0/15.3
6.8 50 200D New 1440 0.86 26.3
8.6 60 440-480Y Standard 1750 0.83 15.1
7.4 60 200D New 1720 0.87 29.0
8.0 60 220D New 1730 0.87 28.0
8.4 60 400Y New 1735 0.87 16.2
8.0 60 380Y New 1730 0.87 16.2
7.5 50 380-420D/660-690Y Standard 1450 0.83 15.3/8.8
8.6 60 440-480D Standard 1750 0.83 15.1
8.4 60 400D New 1735 0.87 16.2
8.0 60 380D New 1730 0.87 16.2
ABB 160 L-4 15.0 50 230D/400Y Standard 1455 0.84 49.0/28.5
14.0 50 200D New 1440 0.86 53.0
17.0 60 440Y Standard 1745 0.84 30.0
14.0 60 200D New 1720 0.85 54.0
16.0 60 220D New 1730 0.85 55.0
16.8 60 400Y New 1735 0.85 32.0
16.0 60 380Y New 1730 0.85 32.0
15.0 50 400D/690Y Standard 1455 0.84 28.5/16.5
17.0 60 440D Standard 1765 0.84 30.0
16.8 60 400D New 1735 0.85 32.0
16.0 60 380D New 1730 0.85 32.0
ABB 180M-4 18.5 50 230D/400Y Standard 1470 0.84 61.0/35.0
18.5 50 200D New 1460 0.85 70.0
21.0 60 440Y Standard 1765 0.85 36.0
18.5 60 200D New 1750 0.84 71.0
20.5 60 220D New 1755 0.85 70.0
21.0 60 400Y New 1755 0.85 41.0
20.5 60 380Y New 1755 0.85 40.0
18.5 50 400D/690Y Standard 1470 0.84 35.0/20.0
21.0 60 440D Standard 1765 0.85 36.0
21.0 60 400D New 1755 0.85 41.0
20.5 60 380D New 1755 0.85 40.0

Technical Data
2-pole motors
Brook Hansen 200 30.0 50 220-240D/380-420Y Standard 2950 97/53

50 200D New 2950 106
30.0 50 380-420D/660-690Y Standard 2950 53/31
60 250-280D/440-480Y Standard 3540 83/46
60 200D New 3540 107
60 220D New 3540 0.89 97
60 440-480D Standard 3540 46
60 400D New 3540 53
60 380D New 3540 55
Brook Hansen 37.0 50 220-240D/380-420Y Standard 2940 118/68
50 200D New 2940 130
37.0 50 380-420D/660-690Y Standard 2940 68/38
60 250-280D/440-480Y Standard 3540 115/54
60 200D New 3540 0.89 131
60 220D New 3540 119
60 440-480D Standard 3540 54
60 400D New 3540 65
60 380D New 3540 69
50 200D New 2955 157
45.0 50 380-420D/660-690Y Standard 2955 83/46
60 250-280D/440-480Y Standard 3555 144/69
60 200D New 3555 158
60 220D New 3555 0.90 144
60 440-480D Standard 3555 69
60 400D New 3555 72
60 380D New 3555 75
50 200D New 2960 189
55.0 50 380-420D/660-690Y Standard 2960 100/55
60 250-280D/440-480Y Standard 3560 173/83
60 200D New 3560 0.90 190
60 220D New 3560 173
60 440-480D Standard 3560 83
60 400D New 3560 100
60 380D New 3560 105
50 200D New 2965 256
75.0 50 380-420D/660-690Y Standard 2965 135/74
60 250-280D/440-480Y Standard 3565 234/115
60 200D New 3565 0.90 257
60 220D New 3565 234
60 440-480D Standard 3565 115
60 400D New 3565 128
60 380D New 3565 135
Table 14.11a Changing motor name plates

Technical Data

Glossary of Terms
15. Glossary of Terms

This section explains the various terms found in this handbook.
Absolute Pressure Total pressure exerted by a fluid i.e. atmospheric pressure plus
gauge pressure.
Absolute Viscosity Measure of how resistive the flow of a fluid is between two layers of
fluid in motion.
Adaptor Connection piece between the motor and back plate on a centrifugal
and liquid ring pump.
Anti-thixotropic Fluid viscosity increases with time under shear conditions.
Back Plate Part of a centrifugal and liquid ring pump, which together with the
pump casing forms the fluid chamber.
Cavitation Vacuous space in the inlet port of a pump normally occupied by fluid.
Centrifugal Tending to move out from the centre.
CIP Cleaning In Place - ability to clean pump system without dismantling

pump and system.
Dead Head Speed Pump speed required to overcome slip for a rotary lobe pump.
Density Fluids mass per unit of volume.
Differential Pressure Total absolute pressure differences across the pump during
operation i.e. discharge pressure minus suction pressure.
Dilatant Fluid viscosity increases as shear rate increases.
Discharge Pressure Pressure at which fluid is leaving the pump.

Glossary of Terms
Duty Point Intersection point between the pump curve and the process curve.
Dynamic Head Energy required to set fluid in motion and to overcome any
resistance to that motion.
Elastomer Non-metallic sealing device that exhibits elastic strain characteristics.
Electropolishing Method of surface finishing achieved by an electro-chemical process.
Flooded Suction Positive inlet pressure/head.
Friction Head Pressure drop on both inlet and discharge sides of the pump due to
frictional losses in fluid flow.
Gauge Pressure Pressure within a gauge that exceeds the surrounding atmospheric
pressure, using atmospheric pressure as a zero reference.
Hydraulic Power Theoretical energy required to pump a given quantity of fluid against
a given total head.
Impeller Pumping element of a centrifugal and liquid ring pump.
Inlet Pressure Pressure at which fluid is entering the pump.
Kinematic Viscosity Measure of how resistive the flow of a fluid is under the influence of
gravity.
Laminar Flow Flow characteristic whereby the fluid moves through the pipe in
concentric layers with its maximum velocity in the centre of the pipe,
decreasing to zero at the pipe wall.
Multi-stage A pump with more than one impeller mounted on the same shaft and
connected so as to act in series.
Newtonian Fluid viscosity is constant with change in shear rate or agitation.
NPSH Net Positive Suction Head describing the inlet condition of a pump
and system.
NPSHa Net Positive Suction Head available in a system.
NPSHr Net Positive Suction Head required from a pump.
NIPA Net Inlet Pressure Available in a system.
NIPR Net Inlet Pressure Required from a pump.

Glossary of Terms
Non-Product Wetted Metallic and elastomeric components not in contact with the fluid
being pumped.
Outlet Pressure Pressure at which fluid is leaving the pump.
Positive Displacement Pump type whereby the fluid pumped is directly displaced.
Pressure Drop Result of frictional losses in pipework, fittings and other process
equipment.
Pressure Shock Result of change in fluid velocity.
Product Wetted Metallic and elastomeric components in contact with the fluid being
pumped.
Psuedoplastic Fluid viscosity decreases as shear rate increases.
Pump Casing Part of a centrifugal and liquid ring pump, which together with the
back plate forms the fluid chamber.
Required Power Power needed at the pump shaft.
Reynolds Number (Re) Ratio of inertia forces to viscous forces giving a value to determine
type of flow characteristic.
Rheology Science of fluid flow.
Rheomalactic Fluid viscosity decreases with time under shear conditions but does
not recover.
Rotodynamic A machine to transfer rotating mechanical energy into kinetic energy

in the form of fluid velocity and pressure.
Rotor Pumping element of a rotary lobe pump.
Rotorcase Part of a rotary lobe pump, which together with the rotorcase cover
forms the pump chamber.
Rotorcase Cover Part of a rotary lobe pump, which together with the rotorcase forms
the pump chamber.
Rumbling Method of surface finishing achieved by vibrating components with

abrasive particulate.
Shotblasting Method of surface finishing achieved by blasting finished

components with small metallic particles at great force.

Glossary of Terms
SIP Steam or Sterilisation In Place - ability to steam clean or sterilise

pump system without dismantling pump and system.
Slip Fluid lost by leakage through the pump clearances of a rotary lobe
pump.
Specific Gravity Ratio of a fluids density to the density of water.
Specific Weight Fluids weight per unit volume.
Static Head Difference in fluid levels.
Static Discharge Head Difference in height between the fluid level and the centre line of the
pump inlet on the discharge side of the pump.
Static Suction Head Difference in height between the fluid level and the centre line of the
pump inlet on the inlet side of the pump.
Suction Lift Fluid level is below the centre line of the pump inlet.
Suction Pressure Pressure at which fluid is entering the pump.
Thermal Shock Rapid temperature change of pumphead components.
Thixotropic Fluid viscosity decreases with time under shear conditions.
Torque Moment of force required to produce rotation.
Total Discharge Head Sum of the static discharge and dynamic heads.
Total Efficiency Relationship between the input power at the pump shaft and output
power in the form of water horsepower.
Total Head Total pressure difference between the total discharge head and the
total suction head of the pump.
Total Static Head Difference in height between the static discharge head and the static
suction head.
Total Suction Head Static suction head less the dynamic head.
Transitional Flow Flow characteristic combining both laminar and turbulent flow
tendencies.
Turbulent Flow Flow characteristic whereby considerable mixing of the fluid takes
place across a pipe section with velocity remaining fairly constant.

Glossary of Terms
Vacuum Pressure in a pumping system below normal atmospheric pressure.
Vapour Pressure Pressure at which a fluid will change to a vapour, at a given

temperature.
Velocity Distance a fluid moves per unit of time.
Viscosity Measure of how resistive a fluid is to flow.
Viscous Power Power loss due to viscous fluid friction within the pump.
Volumetric Efficiency Ratio of actual capacity against theoretical capacity.

Alfa Laval in brief
Alfa Laval is a leading global
provider of specialized products
and engineering solutions.
Our equipment, systems and
services are dedicated to
assisting customers in optimizing
the performance of their
processes. Time and time again.
We help them heat, cool,
separate and transport products
such as oil, water, chemicals,
beverages, foodstuff, starch and
pharmaceuticals.
Our worldwide organization works
closely with customers in almost
Alfa Laval Pump Handbook

100 countries to help them stay Alfa Laval Pump Handbook
ahead.
How to contact Alfa Laval

Contact details for all countries
are continually updated on
our website. Please visit
www.alfalaval.com to access the
information.
PM66050GB1 2001

Alfa Laval Pump Handbook

Uploaded by

Document Informationclick to expand document informationsd

Document Informationclick to expand document information

Copyright:

Available Formats

Alfa Laval Pump Handbook

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Alfa Laval Pump Handbook

Uploaded by

Copyright:

Available Formats

All you need to know ...

Alfa Laval in brief

Alfa Laval Pump Handbook

How to contact Alfa Laval

The information provided in this handbook is given

This pump handbook has been produced to support pump users

2 Terminology and Theory 10 Cleaning Guidelines

3 Pump Selection 11 Compliance with International

Alfa Laval Pump Handbook 1

Section 2: Terminology and Theory 5.1 Main Components 61

Alfa Laval Pump Handbook 2

Alfa Laval Pump Handbook 3

1.1 What is a Pump?

‘A machine used for the purpose of transferring quantities of

This is illustrated below transferring fluid from tank A to spray

Fig. 1.1a Typical pump installation

Pump types generally fall into two main categories - Rotodynamic

The Rotodynamic pump transfers rotating mechanical energy into

The Rotary Lobe pump is a type of positive displacement pump,

Alfa Laval Pump Handbook 5

Positive Displacement Rotodynamic

Rotor Reciprocating Multi-Stage Single Stage

Multi-Rotor Single Rotor Diaphragm Plunger End Suction Double Entry

Screw Piston Simplex Process

Circumferential Piston Archimedian Screw Multiplex Rubber Lined

Gear Flexible Member Submersible

Internal External Peristaltic General

Vane Alfa Laval

Fig. 1.1b Pump classifications

6 Alfa Laval Pump Handbook

2. Terminology and Theory

In order to select a pump two types of data are required:

• Product/Fluid data which includes viscosity, density/specific

Different fluids have varying characteristics and are usually pumped

Alfa Laval Pump Handbook 7

2.1 Product/Fluid Data

Two basic viscosity parameters are commonly used, absolute (or

Absolute (or Dynamic) Viscosity

8 Alfa Laval Pump Handbook

Relationship Between Absolute and Kinematic Viscosity

n=m where r is the fluid density (see 2.1.3).

In the cgs system this translates to:

Kinematic Viscosity (cSt) = Absolute Viscosity (cP)

Absolute Viscosity (cP) = Kinematic Viscosity (cSt) x SG

A viscosity conversion table is included in 14.3.10.

Viscosity Variation with Temperature

often meaningless - viscosity should always be quoted at the

At a constant temperature the viscosity is constant with change in

Typical fluids are:

Alfa Laval Pump Handbook 9

It is not always obvious which Non-Newtonian Fluids

Types of Non-Newtonian Fluids

Typical fluids are:

Fig. 2.1.2e Psuedoplastic Fluids

Typical fluids are:

• Clay Slurries • Paper Coatings

Fig. 2.1.2f Dilatant Fluids

10 Alfa Laval Pump Handbook