Illumination

LUXEON Z ES
Extreme flux density in a micro footprint
package for precise optical control
LUXEON Z ES is a high power 1.6mm x 2.0mm LED that enables never

before seen color consistency, luminance, flux density and design

flexibility for lighting solutions. LUXEON Z ES is undomed, a feature that

provides unmatched optical flexibility for precise beam angle control.

Tested and binned at application conditions, 85°C, LUXEON Z ES emitters

are an ideal choice for indoor and outdoor light sources requiring

superior beam angles, higher efficacy and lower costs.

Features and BENEFITS Primary Applications

Micro footprint enables close packaging Wall Grazer

Undomed design allows precise optical control Linear

3- and 5-step MacAdam ellipse: Freedom from Binning enabling
color consistency Wall Wash

LM-80 test report available Lamps

High Bay

Low Bay

More...

RoHS
COMPLIANT
No. E352519
DS134 LUXEON Z ES Product Datasheet ©2022 Lumileds Holding B.V. All rights reserved.
Table of Contents

General Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Product Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Part Number Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Lumen Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Environmental Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Performance Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Product Selection Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Optical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Electrical and Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Characteristic Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Spectral Power Distribution Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Light Output Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Forward Current Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Radiation Pattern Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Product Bin and Labeling Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Decoding Product Bin Labeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Luminous Flux Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Color Bin Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Forward Voltage Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Mechanical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Soldering Reflow Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
JEDEC Moisture Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Solder Pad Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Packaging Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Pocket Tape Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Reel Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

DS134 LUXEON Z ES Product Datasheet 20220926 ©2022 Lumileds Holding B.V. All rights reserved. i
General Product Information

Product Test Conditions

LUXEON Z ES LEDs are tested and binned with a DC drive current of 700mA at a junction temperature, Tj, of 85°C.

Part Number Nomenclature

Part numbers for LUXEON Z ES follow the convention below:

L X Z A – B C D E – F

Where:

A – designates voltage (2=3V)

B C – designates nominal ANSI CCT or color (22=2200K, 27=2700K, 30=3000K, 35=3500K, 40=4000K,
50=5000K, 57=5700K, 65=6500K)

D E – designates minimum CRI (70=70CRI, 7T=70CRI Typical, 80=80CRI, 90=90CRI)

F – designates color space definition (3=3 SDCM and 5=5 SDCM)

Therefore, the following part number is used for a LUXEON Z ES 3V, 3000K 80CRI, which is binned within a 3-step MacAdam
ellipse:

L X Z 2 – 3 0 8 0 – 3

Lumen Maintenance
Please contact your local Sales Representative or Lumileds Technical Solutions Manager for more information about the long-
term performance of this product.

Environmental Compliance
Lumileds LLC is committed to providing environmentally friendly products to the solid-state lighting market. LUXEON Z ES is
compliant to the European Union directives on the restriction of hazardous substances in electronic equipment, namely the
RoHS Directive 2011/65/EU and REACH Regulation (EC) 1907/2006. Lumileds LLC will not intentionally add the following restricted
materials to its products: lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB) or polybrominated
diphenyl ethers (PBDE).

DS134 LUXEON Z ES Product Datasheet 20220926 ©2022 Lumileds Holding B.V. All rights reserved. 2
Performance Characteristics

Product Selection Guide

Table 1. Product performance of LUXEON Z ES 3V at 700mA and 350mA, Tj=85°C.

Luminous Flux [1] (lm) Typical Typical Typical

Nominal Minimum Luminous Luminous Luminous
Minimum Typical Efficacy (lm/W) Flux (lm) Efficacy (lm/W) Part Number [2]
CCT CRI [1]
700mA 350mA
4000K 70 220 260 133 143 150 LXZ2-4070
5000K 70 220 260 133 143 150 LXZ2-5070
5700K 70 220 270 138 149 156 LXZ2-5770
5700K 70 [3] 250 270 138 149 156 LXZ2-577T
6500K 70 220 270 138 149 156 LXZ2-6570
6500K 70 [3] 250 270 138 149 156 LXZ2-657T
2200K 80 140 188 96 103 109 LXZ2-2280-x
2700K 80 170 216 110 119 125 LXZ2-2780-x
3000K 80 180 230 117 127 133 LXZ2-3080-x
3500K 80 190 240 122 132 139 LXZ2-3580-x
4000K 80 190 248 127 136 144 LXZ2-4080-x
5000K 80 190 250 128 138 145 LXZ2-5080-x
2700K 90 140 180 92 99 104 LXZ2-2790-x
3000K 90 150 190 97 105 110 LXZ2-3090-x
3500K 90 150 197 101 108 114 LXZ2-3590-x
4000K 90 150 205 105 113 119 LXZ2-4090-x
5700K 90 170 215 110 118 124 LXZ2-5790-x
Notes for Table 1:
1. Lumileds maintains a tolerance of ±6.5% on both luminous flux and radiometric power and ±2 on CRI measurements.
2. In the part number the -x is the designation for the white color space requirement. On 80CRI and 90CRI versions 3 designates 3 SDCM and 5 designates 5 SDCM. For 70 CRI parts or lower,
they will not have an SDCM designation and all parts are binned within a 5-step SDCM.
3. Typical CRI.

Optical Characteristics
Table 2. Optical characteristics for LUXEON Z ES at 700mA.

Part Number Typical Total Included Angle [1] Typical Viewing Angle [2]

LXZ2-xxxx 140° 116°

LXZ2-xxxx-x 140° 116°
Notes for Table 2:
1. Total angle at which 90% of total luminous flux is captured.
2. Viewing angle is the off axis angle from the LED centerline where the luminous intensity is ½ of the peak value.

DS134 LUXEON Z ES Product Datasheet 20220926 ©2022 Lumileds Holding B.V. All rights reserved. 3
Electrical and Thermal Characteristics
Table 3. Electrical and thermal characteristics for LUXEON Z ES at 700mA.

FORWARD VOLTAGE [1] (Vf) Typical Temperature TYPICAL THERMAL

Part Number Coefficient of Forward RESISTANCE—JUNCTION
Minimum Typical MAXIMUM VOLTAGE [2] (mV/°C) TO SOLDER PAD (°C/W)

LXZ2-xxxx 2.5 2.8 3.25 -1.6 3

LXZ2-xxxx-x 2.5 2.8 3.25 -1.6 3
Notes for Table 3:
1. Lumileds maintains a tolerance of ±0.06V on forward voltage measurements.
2. Measured between 25°C and 110°C.

Absolute Maximum Ratings

Table 4. Absolute maximum ratings for LUXEON Z ES.

Parameter Maximum Performance

DC Forward Current [1, 2] 1050mA 1200mA 1500mA

Peak Pulsed Forward Current [1, 3] 1200mA 1350mA 1650mA
LED Junction Temperature [1]
(DC & Pulse) 150°C 135°C 85°C
ESD Sensitivity Class 3B
Operating Case Temperature -40°C to 135°C
LED Storage Temperature -40°C to 135°C
Soldering Temperature JEDEC 020c 260°C
Allowable Reflow Cycles 3
Reverse Voltage (Vreverse) [4, 5] LUXEON LEDs are not designed to be driven in reverse bias
Notes for Table 4:
1. Proper current derating must be observed to maintain junction temperature below the maximum allowable junction temperature.
2. Residual periodic variations due to power conversion from alternating current (AC) to direct current (DC), also called “ripple,” are acceptable if the following conditions are met:
– The frequency of the ripple current is 100Hz or higher
– The average current for each cycle does not exceed the maximum allowable DC forward current
– The maximum amplitude of the ripple does not exceed the maximum peak pulsed forward current
3. Pulsed operation with the maximum peak pulsed forward current is acceptable if the pulse on-time is ≤5ms per cycle and the duty cycle is ≤50%.
4. Transient reverse voltages and surge currents due to electrical switching or supply interruptions are acceptable if these events do not last for more than 10ms, the amplitude of the reverse
voltage does not exceed 5V and the reverse current is less than 200uA.
5. A maximum 5V reverse voltage for up to 10s is an acceptable beginning of life, one time, test condition.

DS134 LUXEON Z ES Product Datasheet 20220926 ©2022 Lumileds Holding B.V. All rights reserved. 4
Characteristic Curves

Spectral Power Distribution Characteristics

Figure 1. Typical normalized power vs. wavelength for LXZx-xxxx at test current, Tj=85ºC.

Light Output Characteristics

Figure 2. Typical normalized light output vs. junction temperature for LXZx-xxxx, at test current.

DS134 LUXEON Z ES Product Datasheet 20220926 ©2022 Lumileds Holding B.V. All rights reserved. 5
 Figure 3. Typical normalized light output vs. forward current for LXZx-xxxx, Tj=85ºC.

Forward Current Characteristics

Figure 4. Typical forward current vs. forward voltage for LXZx-xxxx, Tj=85ºC.

DS134 LUXEON Z ES Product Datasheet 20220926 ©2022 Lumileds Holding B.V. All rights reserved. 6
Radiation Pattern Characteristics

Figure 5. Typical radiation pattern for LXZx-xxxx (white only) at test current, Tj=85°C.

Figure 6. Typical polar radiation pattern for LXZx-xxxx (white only) at test current, Tj=85°C.

DS134 LUXEON Z ES Product Datasheet 20220926 ©2022 Lumileds Holding B.V. All rights reserved. 7
Product Bin and Labeling Definitions

Decoding Product Bin Labeling

In the manufacturing of semiconductor products, there are variations in performance around the average values given in the
technical datasheet. For this reason, Lumileds bins LED components for luminous flux or radiometric power, color point, peak or
dominant wavelength and forward voltage.

LUXEON Z ES LEDs are labeled using a 4-digit alphanumeric CAT code following the format below.

A B C D

A – designates luminous flux/radiometric power bin (example: L=200 to 210 lm, M=210 to 220 lm)

B C – designates white color bins (example: 5A, 5B, 5C, 5D, 3U, 3L for 3000K parts)

D – designates forward voltage bin (example: X =2.65 to 2.85V, Y=2.85 to 3.00V)

Therefore, a LUXEON Z ES LED with a lumen range of 200 lm to 210 lm, color bin of 5D and a forward voltage range of 2.65 to
2.85V has the following CAT code:

L 5 D X

DS134 LUXEON Z ES Product Datasheet 20220926 ©2022 Lumileds Holding B.V. All rights reserved. 8
Luminous Flux Bins
Table 5 lists the standard photometric luminous flux bins for LUXEON Z ES emitters. Although several bins are outlined, product
availability in a particular bin varies by production run and by product performance. Not all bins are available in all CCTs.

Table 5. Luminous flux bin definitions for LUXEON Z ES, Tj=85°C.

LUMINOUS FLUX [1] (lm)
Bin
Minimum Maximum
D 130 140
E 140 150
F 150 160
G 160 170
H 170 180
J 180 190
K 190 200
L 200 210
M 210 220
N 220 230
P 230 240
Q 240 250
R 250 260
S 260 270
T 270 280
U 280 290
V 290 300
W 300 310
X 310 320
Y 320 330
Z 330 340
Notes for Table 5:
1. Lumileds maintains a tolerance of ±6.5% on luminous flux measurements.

DS134 LUXEON Z ES Product Datasheet 20220926 ©2022 Lumileds Holding B.V. All rights reserved. 9
Color Bin Definitions

The four lines segmenting the area between

3-Step and 5-step MAE have slope of ±1 when
drawn in CIE 1976 color space, with these
imaginary lines eminating from the MAE center

Figure 7. Color space definition for LUXEON Z ES. Figure 8. 3- and 5-step MacAdam ellipse illustration for Table 6.

Table 6. 3- and 5-step MacAdam ellipse color bin definitions for LUXEON Z ES.
Center Point [2] Major Axis, Minor Axis,
Nominal CCT Color Space [1] Ellipse Rotation
(cx, cy) a b
2200K Single 3-step MacAdam ellipse (0.5020, 0.4156) 0.00863 0.00398 49.27°
2700K Single 3-step MacAdam ellipse (0.4578, 0.4101) 0.00810 0.00420 53.70°
3000K Single 3-step MacAdam ellipse (0.4338, 0.4030) 0.00834 0.00408 53.20°
3500K Single 3-step MacAdam ellipse (0.4073, 0.3917) 0.00927 0.00414 54.0°
4000K Single 3-step MacAdam ellipse (0.3818, 0.3797) 0.00939 0.00402 53.70°
5000K Single 3-step MacAdam ellipse (0.3447, 0.3553) 0.00822 0.00354 59.60°
5700K Single 3-step MacAdam ellipse (0.3287, 0.3417) 0.00746 0.00320 59.09°
2200K Single 5-step MacAdam ellipse (0.5020, 0.4156) 0.01438 0.00663 49.27°
2700K Single 5-step MacAdam ellipse (0.4578, 0.4101) 0.01350 0.00700 53.70°
3000K Single 5-step MacAdam ellipse (0.4338, 0.4030) 0.01390 0.00680 53.20°
3500K Single 5-step MacAdam ellipse (0.4073, 0.3917) 0.01545 0.00690 54.00°
4000K Single 5-step MacAdam ellipse (0.3818, 0.3797) 0.01565 0.00670 53.70°
5000K Single 5-step MacAdam ellipse (0.3447, 0.3553) 0.01370 0.00590 59.60°
5700K Single 5-step MacAdam ellipse (0.3287, 0.3417) 0.01243 0.00533 59.09°
6500K Single 5-step MacAdam ellipse (0.3123, 0.3282) 0.01115 0.00475 58.57°
Notes for Table 6:
1. 3-step is available in 80CRI and 90CRI, and 5-step is available in 70CRI, 80CRI and 90CRI.
2. Lumileds maintains a tolerance of ±0.005 on x and y color coordinates in the CIE color space.

Table 7. MacAdam ellipse color bin definitions for LXZ2-xxxx, Tj=85°C.

Bin SDCM
30 3-step MacAdam ellipse (70CRI, 80CRI, 90CRI)
3U 3-step MacAdam ellipse (80, 90CRI)
3L 3-step MacAdam ellipse (80, 90CRI)
5A 5-step MacAdam ellipse (70, 80, 90CRI)
5B 5-step MacAdam ellipse (70, 80, 90CRI)
5C 5-step MacAdam ellipse (70, 80, 90CRI)
5D 5-step MacAdam ellipse (70, 80, 90CRI)

DS134 LUXEON Z ES Product Datasheet 20220926 ©2022 Lumileds Holding B.V. All rights reserved. 10
Forward Voltage Bins
Table 8. Forward voltage bin definitions for LXZ2-xxxx.
FORWARD VOLTAGE [1] (Vf)
Bin
Minimum Maximum
P 2.50 2.75
R 2.75 3.00
S 3.00 3.25
X 2.65 2.85
Y 2.85 3.00
Notes for Table 8:
1. Lumileds maintains a tolerance of ±0.06V on forward voltage measurements.

Mechanical Dimensions

Figure 9. Mechanical dimensions for LUXEON Z ES.

Notes for Figure 9:

1. Drawings are not to scale.
2. All dimensions are in millimeters.

DS134 LUXEON Z ES Product Datasheet 20220926 ©2022 Lumileds Holding B.V. All rights reserved. 11
Soldering Reflow Guidelines

tp
Tp

Critical Zone
Ramp-up TL to Tp

TL
tL
Temperature

Tsmax

Tsmin
Ramp-down
ts
Preheat Area

25
Time 25ºC to Peak
Time JEDEC J-STD-020D

Figure 10. Visualization of the acceptable reflow temperature profile as specified in Table 9.

Table 9. Reflow profile characteristics for LUXEON Z ES.

PROFILE FEATURE Lead Free Assembly

Preheat Minimum Temperature (Tsmin) 150°C

Preheat Maximum Temperature (Tsmax) 200°C
Preheat Time (tsmin to tsmax) 60 to 120 seconds
Ramp-Up Rate (TL to Tp) 3°C / second maximum
Liquidous Temperature (TL) 217°C
Time Maintained Above Temperature TL (tL) 60 to 150 seconds
Peak / Classification Temperature (Tp) 260°C
Time Within 5°C of Actual Peak Temperature (tp) 20 to 40 seconds
Ramp-Down Rate (Tp to TL) 6°C / second maximum
Time 25°C to Peak Temperature 8 minutes maximum

JEDEC Moisture Sensitivity

Table 10. Moisture sensitivity levels for LUXEON Z ES.
Floor Life Soak Requirements Standard
level
TIme Conditions Time Conditions
1 Unlimited ≤30°C / 85% RH 168 Hours +5 / -0 85°C / 85% RH

DS134 LUXEON Z ES Product Datasheet 20220926 ©2022 Lumileds Holding B.V. All rights reserved. 12
Solder Pad Design

Figure 11. Solder pad layout for LUXEON Z ES.

Notes for Figure 11:

1. All dimensions are in millimeters.
2. The figure shows one of the LUXEON Z ES layouts for close-packing design on Printed Circuit Board (PCB). For more information on assembly and additional layouts, please refer to
LUXEON Z ES Application Brief (AB120).
3. The *.dwg files are available at lumileds.com.

DS134 LUXEON Z ES Product Datasheet 20220926 ©2022 Lumileds Holding B.V. All rights reserved. 13
Packaging Information

Pocket Tape Dimensions

Figure 12. Tape dimensions for LUXEON Z ES.

Notes for Figure 12:

1. Drawings are not to scale.
2. All dimensions are in millimeters.

Reel Dimensions

Figure 13. Reel dimensions for LUXEON Z ES.

Notes for Figure 13:
1. Drawings are not to scale.
2. All dimensions are in millimeters.

DS134 LUXEON Z ES Product Datasheet 20220926 ©2022 Lumileds Holding B.V. All rights reserved. 14
About Lumileds
Companies developing automotive, mobile, IoT and illumination lighting applications need a partner who can collaborate with
them to push the boundaries of light. With over 100 years of inventions and industry firsts, Lumileds is a global lighting solutions
company that helps customers around the world deliver differentiated solutions to gain and maintain a competitive edge. As the
inventor of Xenon technology, a pioneer in halogen lighting and the leader in high performance LEDs, Lumileds builds innovation,
quality and reliability into its technology, products and every customer engagement. Together with its customers, Lumileds is
making the world better, safer, more beautiful—with light.

To learn more about our lighting solutions, visit lumileds.com.

©2022 Lumileds Holding B.V. All rights reserved. Neither Lumileds Holding B.V. nor its affiliates shall be liable for any kind of loss of data or any other damages,
LUXEON is a registered trademark of the Lumileds direct, indirect or consequential, resulting from the use of the provided information and data. Although Lumileds
Holding B.V. in the United States and other countries. Holding B.V. and/or its affiliates have attempted to provide the most accurate information and data, the materials
and services information and data are provided “as is,” and neither Lumileds Holding B.V. nor its affiliates warrants
lumileds.com or guarantees the contents and correctness of the provided information and data. Lumileds Holding B.V. and its
affiliates reserve the right to make changes without notice. You as user agree to this disclaimer and user agree-
ment with the download or use of the provided materials, information and data. A listing of Lumileds product/
patent coverage may be accessed at lumileds.com/patents.
DS134 LUXEON Z ES
Product Datasheet 20220926