SECTION 1 GENERAL

Group 1 Safety Hints -------------------------------------------------------------------------------------------------------- 1-1

Group 2 Specifications ----------------------------------------------------------------------------------------------------- 1-9
 SECTION 1 GENERAL
GROUP 1 SAFETY

FOLLOW SAFE PROCEDURE

Unsafe wor k practices are dangerous.
Understand service procedure before doing
work; do not attempt shortcuts.

WEAR PROTECTIVE CLOTHING

Wear close fitting clothing and safety equipment
appropriate to the job.

13031GE01

WARN OTHERS OF SERVICE WORK

Unexpected machine movement can cause
serious injury.
Before performing any work on the excavator,
attach a 「Do Not Operate」 tag on the right
side control lever.

13031GE02

USE HANDHOLDS AND STEPS

Falling is one of the major causes of personal
injury.
When you get on and off the machine, always
maintain a three point contact with the steps
and handrails and face the machine. Do not use
any controls as handholds.
Never jump on or off the machine. Never mount
or dismount a moving machine.
Be careful of slippery conditions on platforms, 13031GE03

steps, and handrails when leaving the machine.

1-1
PREPARE FOR EMERGENCIES
Be prepared if a fire starts.
Keep a first aid kit and fire extinguisher handy.
Keep emergency numbers for doctors,
ambulance ser vice, hospital, and fire
department near your telephone.

13031GE04

PROTECT AGAINST FLYING DEBRIS

Guard against injury from flying pieces of metal
or debris; wear goggles or safety glasses.

13031GE05

PROTECT AGAINST NOISE

Prolonged exposure to loud noise can cause
impairment or loss of hearing.
Wear a suitable hearing protective device such
as ear-
muffs or ear plugs to protect against
objectionable or uncomfortable loud noises.

13031GE06

AVOID POWER LINES

Serious injury or death can result from contact
with electric lines.
Never move any part of the machine or load
closer to electric line than 3m(10ft) plus twice the
line insulator length.

14W7A1GE07

1-2
KEEP RIDERS OFF EXCAVATOR
Only allow the operator on the excavator. Keep
riders off.
Riders on excavator are subject to injury such
as being struck by foreign objects and being
thrown off the excavator. Riders also obstruct
the operator's view resulting in the excavator
being operated in an unsafe manner.
14W7A1GE08

MOVE AND OPERATE MACHINE SAFELY

Bystanders can be run over. Know the location
of bystanders before moving, swinging, or
operating the machine.
Always keep the travel alarm in working
condition. It warns people when the excavator
starts to move.
Use a signal person when moving, swinging, or
operating the machine in congested areas. 14W7A1GE09

Coordinate hand signals before starting the

excavator.

OPERATE ONLY FORM OPERATOR'S SEAT

Avoid possible injury machine damage. Do not
star t engine by shor ting across star ter
terminals.
NEVER start engine while standing on ground.
Start engine only from operator's seat.

13031GE26

PARK MACHINE SAFELY

Before working on the machine:
·Park machine on a level surface.
·Lower bucket to the ground.
·Turn auto idle switch off.
·Run engine at 1/2 speed without load for 2
minutes.
·Turn key switch to OFF to stop engine.
Remove key from switch.
·Move pilot control shutoff lever to locked
position.
·Allow engine to cool.

1-3
SUPPORT MACHINE PROPERLY
Always lower the attachment or implement to
the ground before you work on the machine. If
you must wor k on a lifted machine or
attachment, securely support the machine or
attachment.
Do not support the machine on cinder blocks,
hollow tiles, or props that may crumble under
continuous load.
13031GE10
Do not work under a machine that is supported
solely by a jack. Follow recommended
procedures in this manual.

SERVICE COOLING SYSTEM SAFELY

Explosive release of fluids from pressurized
cooling system can cause serious burns.
Shut off engine. Only remove filler cap when
cool enough to touch with bare hands.

13031GE11

HANDLE FLUIDS SAFELY-AVOID FIRES

Handle fuel with care; it is highly flammable. Do
not refuel the machine while smoking or when
near open flame or sparks. Always stop engine
before refueling machine.
Fill fuel tank outdoors.

13031GE12

Store flammable fluids away from fire hazards.

Do not incinerate or puncture pressurized
containers.
Make sure machine is clean of trash, grease,
and debris.
Do not store oily rags ; they can ignite and burn
spontaneously.

13031GE13

1-4
BEWARE OF EXHAUST FUMES
Prevent asphyxiation. Engine exhaust fumes
can cause sickness or death.
If you must operate in a building, be positive
there is adequate ventilation. Either use an
exhaust pipe extension to remove the exhaust
fumes or open doors and windows to bring
enough outside air into the area.

REMOVE PAINT BEFORE WELDING OR

HEATING
Avoid potentially toxic fumes and dust.
Hazardous fumes can be generated when paint
is heated by welding, soldering, or using a torch.
Do all work outside or in a well ventilated area.
Dispose of paint and solvent properly.
Remove paint before welding or heating:
·If you sand or grind paint, avoid breathing the
dust.
Wear an approved respirator.
·If you use solvent or paint stripper, remove
stripper with soap and water before welding.
Remove solvent or paint stripper containers 13031GE14

and other flammable material from area.

Allow fumes to disperse at least 15 minutes
before welding or heating.

ILLUMINATE WORK AREA SAFELY

Illuminate your work area adequately but safely.
Use a portable safety light for working inside or
under the machine. Make sure the bulb is
enclosed by a wire cage. The hot filament of an
accidentally broken bulb can ignite spilled fuel
or oil.

13031GE15

1-5
SERVICE MACHINE SAFELY
Tie long hair behind your head. Do not wear a
necktie, scarf, loose clothing or necklace when
you work near machine tools or moving parts. If
these items were to get caught, severe injury
could result.
Remove rings and other jewelry to prevent
electrical shorts and entanglement in moving
parts.
13031GE16

STAY CLEAR OF MOVING PARTS

Entanglements in moving parts can cause
serious injury.
To prevent accidents, use care when working
around rotating parts.

13031GE17

AVOID HIGH PRESSURE FLUIDS

Escaping fluid under pressure can penetrate the
skin causing serious injury.
Avoid the hazard by relieving pressure before
disconnecting hydraulic or other lines. Tighten
all connections before applying pressure.
Search for leaks with a piece of cardboard.
Protect hands and body from high pressure
fluids. 13031GE18

If an accident occurs, see a doctor immediately.

Any fluid injected into the skin must be
surgically removed within a few hours or
gangrene may result.

13031GE19

1-6
AVOID HEATING NEAR PRESSURIZED
FLUID LINES
Flammable spray can be generated by heating
near pressurized fluid lines, resulting in severe
burns to yourself and bystanders. Do not heat
by welding, soldering, or using a torch near
pressurized fluid lines or other flammable
materials.
Pressurized lines can be accidentally cut when
13031GE20
heat goes beyond the immediate flame area.
Install fire resisting guards to protect hoses or
other materials.

PREVENT BATTERY EXPLOSIONS

Keep sparks, lighted matches, and flame away
from the top of battery. Battery gas can
explode.
Never check battery charge by placing a metal
object across the posts. Use a volt-meter or
hydrometer.
Do not charge a frozen battery; it may explode.
Warm battery to 16˚C (60˚F). 13031GE21

PREVENT ACID BURNS

Sulfuric acid in battery electrolyte is poisonous.
It is strong enough to burn skin, eat holes in
clothing, and cause blindness if splashed into
eyes.
Avoid the hazard by:
1. Filling batteries in a well-ventilated area.
2. Wearing eye protection and rubber gloves.
3. Avoiding breathing fumes when electrolyte is
added.
4. Avoiding spilling of dripping electrolyte.
5. Use proper jump start procedure.
If you spill acid on yourself:
1. Flush your skin with water.
2. Apply baking soda or lime to help neutralize
the acid.
3. Flush your eyes with water for 10-15
minutes. Get medical attention immediately.
If acid is swallowed:
1. Drink large amounts of water or milk.
2. Then drink milk of magnesia, beaten eggs, 13031GE22

or vegetable oil.
3. Get medical attention immediately.

1-7
USE TOOLS PROPERLY
Use tools appropriate to the work. Makeshift
tools, parts, and procedures can create safety
hazards.
Use power tools only to loosen threaded tools
and fasteners.
For loosening and tightening hardware, use the
correct size tools. DO NOT use U.S.
measurement tools on metric fasteners. Avoid
bodily injury caused by slipping wrenches.
13031GE23
Use only recommended replacement parts.
(See Parts manual.)

DISPOSE OF FLUIDS PROPERLY

Improperly disposing of fluids can harm the
environment and ecology. Before draining any
fluids, find out the proper way to dispose of
waste from your local environmental agency.
Use proper containers when draining fluids. Do
not use food or beverage containers that may
mislead someone into drinking from them.
DO NOT pour oil into the ground, down a drain,
or into a stream, pond, or lake. Observe
relevant environmental protection regulations 13031GE24

when disposing of oil, fuel, coolant, brake fluid,

filters, batteries, and other harmful waste.

REPLACE SAFETY SIGNS

Replace missing or damaged safety signs. See
the machine operator's manual for correct
safety sign placement.

13031GE25

LIVE WITH SAFETY

Before returning machine to customer, make
sure machine is functioning properly, especially
the safety systems. Install all guards and
shields.

1-8
 GROUP 2 SPECIFICATIONS

1. MAJOR COMPONENT

Bucket Tooth Battery box DEF/AdBlue tank Fuel tank Hydraulic tank
R

Main pump
After
treatment
device

Engine

Radiator
Oil cooler
Charge air cooler

Turning joint Swing motor Main control valve

Arm Arm cylinder Boom Boom cylinder Cab Counterweight

Swing bearing

Dozer blade

Tire
Bucket cylinder Connecting rod Front axle Travel motor Tool box Rear axle

Connecting link Side cutter Front drive shaft Transmission Rear drive shaft

140WA2SP01

1-9
 2. SPECIFICATIONS
1) HW140A. MONO BOOM
I(I') D
C

E
G
F
H
J K
A B(L)

140WF2SP02A

Unit Specification
Description m Boom 4.6 (15' 1")
(ft-in) Arm 2.45 (8' 0") 2.00 (6' 50") 2.60 (8' 5") 3.10 (10' 20")
Operating weight kg (lb) 14900 (32850) 14840 (32720) 14920 (32890) 14970 (33000)
Bucket capacity (SAE heaped), standard m³ (yd³) 0.58 (0.76) 0.58 (0.76) 0.58 (0.76) 0.58 (0.76)
Overall length (traveling) 7560 (24' 10") 7740 (25' 5") 7470 (24' 6") 7360 (24' 2")
A
Overall length (shipping) 7660 (25' 2") 7600 (24' 11") 7670 (25' 2") 7600 (24' 11")
Overall width B 2530 (8' 4") 2530 (8' 4") 2530 (8' 4") 2530 (8' 4")
Overall height of boom C 3805 (12' 6") 3420 (11' 3") 3925 (12' 11") 4000 (13' 1")
Upperstructure width D 2485 (8' 2") 2485 (8' 2") 2485 (8' 2") 2485 (8' 2")
Cab height E 3255 (10' 8") 3255 (10' 8") 3255 (10' 8") 3255 (10' 8")
Ground clearance of counterweight F 1260 (4' 2") 1260 (4' 2") 1260 (4' 2") 1260 (4' 2")
Engine cover height G mm (ft-in) 2760 (9' 1") 2760 (9' 1") 2760 (9' 1") 2760 (9' 1")
Minimum ground clearance H 390 (1' 3") 390 (1' 3") 390 (1' 3") 390 (1' 3")
Rear-end distance I 2150 (7' 1") 2150 (7' 1") 2150 (7' 1") 2150 (7' 1")
Rear-end swing radius I' 2170 (7' 1") 2170 (7' 1") 2170 (7' 1") 2170 (7' 1")
Wheel base J 2600 (8' 6") 2600 (8' 6") 2600 (8' 6") 2600 (8' 6")
Tread K 1944 (6' 5") 1944 (6' 5") 1944 (6' 5") 1944 (6' 5")
Dozer blade width L 2490 (8' 2") 2490 (8' 2") 2490 (8' 2") 2490 (8' 2")
Overall height of guardrail N 3475 (11' 5") 3475 (11' 5") 3475 (11' 5") 3475 (11' 5")
Low 10 (6.2) 10 (6.2) 10 (6.2) 10 (6.2)
Travel speed High km/hr (mph) 40 (24.9) 40 (24.9) 40 (24.9) 40 (24.9)
Creep 3 (1.9) 3 (1.9) 3 (1.9) 3 (1.9)
Swing speed rpm 9.50 9.50 9.50 9.50
Gradeability Degree (%) 35 (70) 35 (70) 35 (70) 35 (70)
Max traction force kg (lb) 8163 (17996) 8163 (17996) 8163 (17996) 8163 (17996)

1-10
 2) HW140A, 2-PIECE BOOM

I(I') D
C

E
G
F
H
J K
A B(L)

140WA2SP03A

Unit Specification
Description m Boom 4.71 (15' 5")
(ft-in) Arm 2.45 (8' 0") 2.00 (6' 50") 2.60 (8' 5")
Operating weight kg (lb) 15860 (34970) 15800 (34830) 15880 (35010)
Bucket capacity (SAE heaped), standard m³ (yd³) 0.58 (0.76) 0.58 (0.76) 0.58 (0.76)
Overall length (traveling) 5810 (19' 1") 5840 (19' 2") 5785 (19' 0")
A
Overall length (shipping) 7770 (25' 6") 7770 (25' 6") 7780 (25' 6")
Overall width B 2530 (8' 4") 2530 (8' 4") 2530 (8' 4")
Overall height of boom C 3990 (13' 1") 4000 (13' 1") 4000 (13' 1")
Upperstructure width D 2485 (8' 2") 2485 (8' 2") 2485 (8' 2")
Cab height E 3255 (10' 8") 3255 (10' 8") 3255 (10' 8")
Ground clearance of counterweight F 1260 (4' 2") 1260 (4' 2") 1260 (4' 2")
Engine cover height G mm (ft-in) 2760 (9' 1") 2760 (9' 1") 2760 (9' 1")
Minimum ground clearance H 390 (1' 3") 390 (1' 3") 390 (1' 3")
Rear-end distance I 2150 (7' 1") 2150 (7' 1") 2150 (7' 1")
Rear-end swing radius I' 2170 (7' 1") 2170 (7' 1") 2170 (7' 1")
Wheel base J 2600 (8' 6") 2600 (8' 6") 2600 (8' 6")
Tread K 1944 (6' 5") 1944 (6' 5") 1944 (6' 5")
Dozer blade width L 2490 (8' 2") 2490 (8' 2") 2490 (8' 2")
Overall height of guardrail N 3475 (11' 5") 3475 (11' 5") 3475 (11' 5")
Low 10 (6.2) 10 (6.2) 10 (6.2)
Travel speed High km/hr (mph) 40 (24.9) 40 (24.9) 40 (24.9)
Creep 3 (1.9) 3 (1.9) 3 (1.9)
Swing speed rpm 9.50 9.50 9.50
Gradeability Degree (%) 35 (70) 35 (70) 35 (70)
Max traction force kg (lb) 8163 (17996) 8163 (17996) 8163 (17996)

1-11
 3. WORKING RANGE AND DIGGING POWER
1) HW140A, MONO BOOM
A
A'
F

D
B' E
C
B

8ft
140WA2SP04

Description 2.45 m (8' 0") Arm 2.00 m (6' 7") Arm 2.60 m (8' 6") Arm 3.10 m (10' 2") Arm
Max digging reach A 8310 ( 27' 3" ) 7880 ( 25' 10" ) 8450 ( 27' 9" ) 8910 ( 29' 3" )
Max digging reach on ground A' 8080 ( 26' 6" ) 7640 ( 25' 1" ) 8230 ( 27' 0" ) 8700 ( 28' 7" )
Max digging depth B 5110 ( 16' 9" ) 4660 ( 15' 3" ) 5260 ( 17' 3" ) 5760 ( 18' 11" )
Max digging depth (8 ft level) B' 4895 ( 16' 1" ) 4400 ( 14' 5" ) 5060 ( 16' 7" ) 5580 ( 18' 4" )
Max vertical wall digging depth C 4655 ( 15' 3" ) 4200 ( 13' 9" ) 4800 ( 15' 9" ) 5310 ( 17' 5" )
Max digging height D 8850 ( 29' 0" ) 8540 ( 28' 0" ) 8940 ( 29' 4" ) 9210 ( 30' 3" )
Max dumping height E 6400 ( 21' 0" ) 6100 ( 20' 0" ) 6490 ( 21' 4" ) 6760 ( 22' 2" )
Min swing radius F 2680 ( 8' 10" ) 2670 ( 8' 9" ) 2690 ( 8' 10" ) 2720 ( 8' 11" )
87.9 [95.9] 87.8 [95.8] 87.9 [95.9] 87.8 [95.8]
SAE 8961 [9780] 8957 [9770] 8961 [9780] 8957 [9770]
19760 [21560] 19750 [21540] 19760 [21560] 19750 [21540]
Bucket digging force
102.9 [112.3] 102.9 [112.2] 102.9 [112.3] 102.9 [112.2]
ISO 10494 [11450] 10489.4 [11440] 10494 [11450] 10488.6 [11440]
23140 [25240] 23130 [25220] 23140 [25240] 23120 [25220]
63.6 [69.3] 74.2 [81.0] 61.1 [66.7] 54.7 [59.7]
SAE 6485 [7070] 7569 [8260] 6230 [6800] 5579 [6090]
14300 [15590] 16690 [18210] 13740 [14990] 12300 [13430]
Arm digging force
66.3 [72.4] 77.9 [84.9] 63.6 [69.4] 56.7 [61.9]
ISO 6764 [7380] 7942 [8660] 6486 [7080] 5782 [6310]
14910 [16270] 17510 [19090] 14300 [15610] 12750 [13910]
[ ] : Power boost

1-12
 2) HW140A, 2-PIECE BOOM
A
A'
F

D
E
C
B'
B

8ft
140WA2SP05

Description 2.45 m (8' 0") Arm 2.00 m (6' 7") Arm 2.60 m (8' 6") Arm
Max digging reach A 8490 ( 27' 10" ) 8050 ( 26' 5" ) 8630 ( 28' 4" )
Max digging reach on ground A' 8270 ( 27' 2" ) 7820 ( 25' 8" ) 8420 ( 27' 7" )
Max digging depth B 5000 ( 16' 5" ) 4550 ( 14' 11" ) 5150 ( 16' 11" )
Max digging depth (8 ft level) B' 4890 ( 16' 1" ) 4430 ( 14' 6" ) 5040 ( 16' 6" )
Max vertical wall digging depth C 4410 ( 14' 6" ) 3930 ( 12' 11" ) 4555 ( 14' 11" )
Max digging height D 9480 ( 31' 1" ) 9120 ( 29' 11" ) 9600 ( 31' 6" )
Max dumping height E 6990 ( 22' 11" ) 6640 ( 21' 9" ) 7110 ( 23' 4" )
Min swing radius F 2600 ( 8' 6" ) 2620 ( 8' 7" ) 2650 ( 8' 8" )
87.9 [95.9] 87.8 [95.8] 87.9 [95.9]
SAE 8961 [9780] 8957 [9770] 8961 [9780]
19760 [21560] 19750 [21540] 19760 [21560]
Bucket digging force
102.9 [112.3] 102.9 [112.2] 102.9 [112.3]
ISO 10494 [11450] 10489 [11440] 10494 [11450]
23140 [25240] 23130 [25220] 23140 [25240]
63.6 [69.3] 74.2 [81.0] 61.1 [66.7]
SAE 6485 [7070] 7569 [8260] 6230 [6800]
14300 [15590] 16690 [18210] 13740 [14990]
Arm digging force
66.3 [72.4] 77.9 [84.9] 63.6 [69.4]
ISO 6764 [7380] 7942 [8660] 6486 [7080]
14910 [16270] 17510 [19090] 14300 [15610]
[ ] : Power boost

1-13
4. WEIGHT
HW140A
Item
kg lb
Upperstructure assembly 7005 15440
·Main frame weld assembly 1273 2810
·Engine assembly 378 830
·Aftertreatment assembly 64 140
·Main pump assembly 91 200
·Main control valve assembly 144 320
·Swing motor assembly 148 330
·Hydraulic oil tank WA 135 300
·Fuel tank WA 138 300
·Counterweight 1704 3760
·Cab assembly 495 1090
Lower chassis assembly 5145 11340
·Lower frame weld assembly 1255 2770
·Swing bearing 260 570
·Travel motor assembly (2EA) 56 120
·Turning joint 117 260
·Transmission assembly 135 300
·Front axle assembly 637 1400
·Rear axle assembly 534 1180
·Dozer blade assembly (front) 632 1390
·Dozer blade assembly (rear) 632 1390
Front attachment assembly 2750 6060
(4.6 m boom, 2.45 m arm, 0.58 m3 SAE heaped bucket)
·4.6 m boom assembly 829 1830
·4.71 m 2-piece boom assembly 938 2070
·2.00 m arm assembly 380 840
·2.45 m arm assembly 437 960
·2.60 m arm assembly 457 1010
·3.10 m arm assembly 492 1080
·0.58 m3 SAE heaped bucket assembly 484 1070
·0.52 m3 SAE heaped bucket assembly 461 1020
·0.65 m3 SAE heaped bucket assembly 513 1130
·0.71 m3 SAE heaped bucket assembly 536 1180
·0.50 m3 SAE heaped bucket assembly 439 970
·0.61 m3 SAE heaped bucket assembly 490 1080
·0.45 m3 SAE heaped bucket assembly 410 900
·0.55 m3 SAE heaped bucket assembly 585 1290
·Bucket control link assembly 113 250
·Boom cylinder assembly (2EA) 238 520
·Adjustable boom cylinder assembly (2EA) 246 540
·Arm cylinder assembly 145 320
·Bucket cylinder assembly 104 230
·Adjustable cylinder assembly 168 370
·Oscillating cylinder assembly (2EA) 98 220
·Outrigger cylinder assembly (2EA) 136 300
·Blade cylinder assembly (front) (2EA) 102 220
·Blade cylinder assembly (rear) (2EA) 102 220
·Front outrigger assembly 833 1840
·Rear outrigger assembly 833 1840

1-14
5. LIFTING CAPACITIES
1) 4.6 m MONO BOOM+1700 kg COUNTERWEIGHT

Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger

MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HW140A
BOOM 4600 2000 1700 - 500 - Down - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 1.5 m (4.9 ft) 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) Capacity Reach
height (A)
m (ft)
6.0 m kg *4420 3670 *3330 2910 5.15
(19.7 ft) lb *9740 8090 *7340 6420 (16.9)
4.5 m kg *4790 3570 3560 2240 *3110 2190 6.08
(14.8 ft) lb *10560 7870 7850 4940 *6860 4830 (19.9)
3.0 m kg 5500 3350 3490 2180 3050 1900 6.53
(9.8 ft) lb 12130 7390 7690 4810 6720 4190 (21.4)
1.5 m kg 5250 3140 3400 2090 2940 1810 6.62
(4.9 ft) lb 11570 6920 7500 4610 6480 3990 (21.7)
0.0 m kg *6510 5520 5120 3020 3340 2040 3090 1890 6.34
(0.0 ft) lb *14350 12170 11290 6660 7360 4500 6810 4170 (20.8)
-1.5 m kg *6490 *6490 *9460 5580 5120 3020 3650 2230 5.66
(-4.9 ft) lb *14310 *14310 *20860 12300 11290 6660 8050 4920 (18.6)
-3.0 m kg *6990 5760 *4600 3300 4.37
(-9.8 ft) lb *15410 12700 *10140 7280 (14.3)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause surious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

1-15
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HW140A
BOOM 4600 2000 1700 - 500 - Up - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 1.5 m (4.9 ft) 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) Capacity Reach
height (A)
m (ft)
6.0 m kg *4420 3330 *3330 2640 5.15
(19.7 ft) lb *9740 7340 *7340 5820 (16.9)
4.5 m kg *4790 3230 3560 2020 *3110 1970 6.08
(14.8 ft) lb *10560 7120 7850 4450 *6860 4340 (19.9)
3.0 m kg 5500 3010 3490 1960 3050 1710 6.53
(9.8 ft) lb 12130 6640 7690 4320 6720 3770 (21.4)
1.5 m kg 5250 2810 3400 1880 2940 1620 6.62
(4.9 ft) lb 11570 6190 7500 4140 6480 3570 (21.7)
0.0 m kg *6510 4840 5120 2700 3340 1820 3090 1700 6.34
(0.0 ft) lb *14350 10670 11290 5950 7360 4010 6810 3750 (20.8)
-1.5 m kg *6490 *6490 *9460 4900 5120 2690 3650 1990 5.66
(-4.9 ft) lb *14310 *14310 *20860 10800 11290 5930 8050 4390 (18.6)
-3.0 m kg *6990 5080 *4600 2950 4.37
(-9.8 ft) lb *15410 11200 *10140 6500 (14.3)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause surious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

1-16
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HW140A
BOOM 4600 2450 1700 - 500 - Down - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 1.5 m (4.9 ft) 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) Capacity Reach
height (A)
m (ft)
7.5 m kg *2890 *2890 4.16
(24.6 ft) lb *6370 *6370 (13.6)
6.0 m kg *3880 3740 *2390 *2390 5.70
(19.7 ft) lb *8550 8250 *5270 *5270 (18.7)
4.5 m kg *4330 3620 3590 2270 *2250 1940 6.55
(14.8 ft) lb *9550 7980 7910 5000 *4960 4280 (21.5)
3.0 m kg *7850 6310 *5330 3390 3500 2180 *2260 1700 6.97
(9.8 ft) lb *17310 13910 *11750 7470 7720 4810 *4980 3750 (22.9)
1.5 m kg *5690 5650 5270 3150 3390 2080 *2410 1630 7.05
(4.9 ft) lb *12540 12460 11620 6940 7470 4590 *5310 3590 (23.1)
0.0 m kg *6760 5460 5100 3000 3310 2010 *2740 1690 6.79
(0.0 ft) lb *14900 12040 11240 6610 7300 4430 *6040 3730 (22.3)
-1.5 m kg *5600 *5600 *9980 5480 5060 2960 3300 2000 3190 1940 6.16
(-4.9 ft) lb *12350 *12350 *22000 12080 11160 6530 7280 4410 7030 4280 (20.2)
-3.0 m kg *7990 5620 5160 3050 4400 2650 5.01
(-9.8 ft) lb *17610 12390 11380 6720 9700 5840 (16.4)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause surious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

1-17
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HW140A
BOOM 4600 2450 1700 - 500 - Up - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 1.5 m (4.9 ft) 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) Capacity Reach
height (A)
m (ft)
7.5 m kg *2890 *2890 4.16
(24.6 ft) lb *6370 *6370 (13.6)
6.0 m kg *3880 3390 *2390 2250 5.70
(19.7 ft) lb *8550 7470 *5270 4960 (18.7)
4.5 m kg *4330 3280 3590 2050 *2250 1750 6.55
(14.8 ft) lb *9550 7230 7910 4520 *4960 3860 (21.5)
3.0 m kg *7850 5600 *5330 3050 3500 1970 *2260 1530 6.97
(9.8 ft) lb *17310 12350 *11750 6720 7720 4340 *4980 3370 (22.9)
1.5 m kg *5690 4970 5270 2810 3390 1860 *2410 1460 7.05
(4.9 ft) lb *12540 10960 11620 6190 7470 4100 *5310 3220 (23.1)
0.0 m kg *6760 4790 5100 2670 3310 1790 *2740 1510 6.79
(0.0 ft) lb *14900 10560 11240 5890 7300 3950 *6040 3330 (22.3)
-1.5 m kg *5600 *5600 *9980 4800 5060 2640 3300 1790 3190 1730 6.16
(-4.9 ft) lb *12350 *12350 *22000 10580 11160 5820 7280 3950 7030 3810 (20.2)
-3.0 m kg *7990 4940 5160 2720 4400 2370 5.01
(-9.8 ft) lb *17610 10890 11380 6000 9700 5220 (16.4)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause surious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

1-18
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HW140A
BOOM 4600 2600 1700 - 500 - Down - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 1.5 m (4.9 ft) 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) Capacity Reach
height (A)
m (ft)
7.5 m kg *2660 *2660 4.40
(24.6 ft) lb *5860 *5860 (14.4)
6.0 m kg *2230 *2230 5.87
(19.7 ft) lb *4920 *4920 (19.3)
4.5 m kg *4180 3650 3610 2280 *2100 1870 6.70
(14.8 ft) lb *9220 8050 7960 5030 *4630 4120 (22.0)
3.0 m kg *7510 6380 *5190 3410 3510 2190 *2110 1650 7.12
(9.8 ft) lb *16560 14070 *11440 7520 7740 4830 *4650 3640 (23.3)
1.5 m kg *6430 5680 5280 3150 3390 2080 *2250 1580 7.19
(4.9 ft) lb *14180 12520 11640 6940 7470 4590 *4960 3480 (23.6)
0.0 m kg *6820 5440 5090 2990 3300 2000 *2540 1630 6.94
(0.0 ft) lb *15040 11990 11220 6590 7280 4410 *5600 3590 (22.8)
-1.5 m kg *5360 *5360 *10110 5440 5040 2950 3290 1990 3060 1860 6.33
(-4.9 ft) lb *11820 *11820 *22290 11990 11110 6500 7250 4390 6750 4100 (20.8)
-3.0 m kg *9520 *9520 *8270 5580 5120 3020 4130 2490 5.21
(-9.8 ft) lb *20990 *20990 *18230 12300 11290 6660 9110 5490 (17.1)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause surious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

1-19
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HW140A
BOOM 4600 2600 1700 - 500 - Up - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 1.5 m (4.9 ft) 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) Capacity Reach
height (A)
m (ft)
7.5 m kg *2660 *2660 4.40
(24.6 ft) lb *5860 *5860 (14.4)
6.0 m kg *2230 2140 5.87
(19.7 ft) lb *4920 4720 (19.3)
4.5 m kg *4180 3300 3610 2060 *2100 1690 6.70
(14.8 ft) lb *9220 7280 7960 4540 *4630 3730 (22.0)
3.0 m kg *7510 5670 *5190 3070 3510 1970 *2110 1480 7.12
(9.8 ft) lb *16560 12500 *11440 6770 7740 4340 *4650 3260 (23.3)
1.5 m kg *6430 5000 5280 2820 3390 1870 *2250 1410 7.19
(4.9 ft) lb *14180 11020 11640 6220 7470 4120 *4960 3110 (23.6)
0.0 m kg *6820 4770 5090 2660 3300 1790 *2540 1460 6.94
(0.0 ft) lb *15040 10520 11220 5860 7280 3950 *5600 3220 (22.8)
-1.5 m kg *5360 *5360 *10110 4760 5040 2620 3290 1770 3060 1660 6.33
(-4.9 ft) lb *11820 *11820 *22290 10490 11110 5780 7250 3900 6750 3660 (20.8)
-3.0 m kg *9520 *9520 *8270 4900 5120 2690 4130 2220 5.21
(-9.8 ft) lb *20990 *20990 *18230 10800 11290 5930 9110 4890 (17.1)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause surious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

1-20
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HW140A
BOOM 4600 3100 1700 - 500 - Down - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 1.5 m (4.9 ft) 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) 7.5 m (24.6 ft) Capacity Reach
height (A)
m (ft)

7.5 m kg *2150 *2150 5.13

(24.6 ft) lb *4740 *4740 (16.8)
6.0 m kg *2670 2340 *1860 *1860 6.43
(19.7 ft) lb *5890 5160 *4100 *4100 (21.1)
4.5 m kg *3310 2310 *1770 1660 7.20
(14.8 ft) lb *7300 5090 *3900 3660 (23.6)
3.0 m kg *6350 *6350 *4690 3470 3530 2210 *2090 1510 *1790 1480 7.58
(9.8 ft) lb *14000 *14000 *10340 7650 7780 4870 *4610 3330 *3950 3260 (24.9)
1.5 m kg *9370 5840 5330 3190 3400 2080 2400 1460 *1900 1410 7.65
(4.9 ft) lb *20660 12870 11750 7030 7500 4590 5290 3220 *4190 3110 (25.1)
0.0 m kg *7170 5460 5100 2990 3290 1980 *2120 1450 7.42
(0.0 ft) lb *15810 12040 11240 6590 7250 4370 *4670 3200 (24.3)
-1.5 m kg *4710 *4710 *9570 5380 5010 2910 3240 1940 *2570 1620 6.85
(-4.9 ft) lb *10380 *10380 *21100 11860 11050 6420 7140 4280 *5670 3570 (22.5)
-3.0 m kg *7920 *7920 *9090 5470 5040 2940 3430 2070 5.84
(-9.8 ft) lb *17460 *17460 *20040 12060 11110 6480 7560 4560 (19.1)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause surious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

1-21
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HW140A
BOOM 4600 3100 1700 - 500 - Up - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 1.5 m (4.9 ft) 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) 7.5 m (24.6 ft) Capacity Reach
height (A)
m (ft)

7.5 m kg *2150 *2150 5.13

(24.6 ft) lb *4740 *4740 (16.8)
6.0 m kg *2670 2120 *1860 1850 6.43
(19.7 ft) lb *5890 4670 *4100 4080 (21.1)
4.5 m kg *3310 2090 *1770 1490 7.20
(14.8 ft) lb *7300 4610 *3900 3280 (23.6)
3.0 m kg *6350 5900 *4690 3130 3530 1990 *2090 1350 *1790 1320 7.58
(9.8 ft) lb *14000 13010 *10340 6900 7780 4390 *4610 2980 *3950 2910 (24.9)
1.5 m kg *9370 5150 5330 2860 3400 1870 2400 1310 *1900 1260 7.65
(4.9 ft) lb *20660 11350 11750 6310 7500 4120 5290 2890 *4190 2780 (25.1)
0.0 m kg *7170 4780 5100 2660 3290 1770 *2120 1290 7.42
(0.0 ft) lb *15810 10540 11240 5860 7250 3900 *4670 2840 (24.3)
-1.5 m kg *4710 *4710 *9570 4710 5010 2580 3240 1730 *2570 1440 6.85
(-4.9 ft) lb *10380 *10380 *21100 10380 11050 5690 7140 3810 *5670 3170 (22.5)
-3.0 m kg *7920 *7920 *9090 4790 5040 2610 3430 1840 5.84
(-9.8 ft) lb *17460 *17460 *20040 10560 11110 5750 7560 4060 (19.1)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause surious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

1-22
 2) 4.6 m MONO BOOM+2200 kg COUNTERWEIGHT

Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger

MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HW140A
BOOM 4600 2000 2200 - 500 - Down - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 1.5 m (4.9 ft) 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) Capacity Reach
height (A)
m (ft)
6.0 m kg *4420 4000 *3330 3180 5.15
(19.7 ft) lb *9740 8820 *7340 7010 (16.9)
4.5 m kg *4790 3890 *3600 2460 *3110 2410 6.08
(14.8 ft) lb *10560 8580 *7940 5420 *6860 5310 (19.9)
3.0 m kg *5740 3670 3780 2400 *3140 2100 6.53
(9.8 ft) lb *12650 8090 8330 5290 *6920 4630 (21.4)
1.5 m kg 5680 3460 3680 2320 3190 2010 6.62
(4.9 ft) lb 12520 7630 8110 5110 7030 4430 (21.7)
0.0 m kg *6510 6090 5550 3350 3620 2260 3350 2100 6.34
(0.0 ft) lb *14350 13430 12240 7390 7980 4980 7390 4630 (20.8)
-1.5 m kg *6490 *6490 *9460 6150 5540 3340 3960 2470 5.66
(-4.9 ft) lb *14310 *14310 *20860 13560 12210 7360 8730 5450 (18.6)
-3.0 m kg *6990 6340 *4600 3630 4.37
(-9.8 ft) lb *15410 13980 *10140 8000 (14.3)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause surious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

1-23
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HW140A
BOOM 4600 2000 2200 - 500 - Up - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 1.5 m (4.9 ft) 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) Capacity Reach
height (A)
m (ft)
6.0 m kg *4420 3630 *3330 2900 5.15
(19.7 ft) lb *9740 8000 *7340 6390 (16.9)
4.5 m kg *4790 3540 *3600 2240 *3110 2190 6.08
(14.8 ft) lb *10560 7800 *7940 4940 *6860 4830 (19.9)
3.0 m kg *5740 3320 3780 2180 *3140 1900 6.53
(9.8 ft) lb *12650 7320 8330 4810 *6920 4190 (21.4)
1.5 m kg 5680 3110 3680 2090 3190 1820 6.62
(4.9 ft) lb 12520 6860 8110 4610 7030 4010 (21.7)
0.0 m kg *6510 5380 5550 3000 3620 2040 3350 1900 6.34
(0.0 ft) lb *14350 11860 12240 6610 7980 4500 7390 4190 (20.8)
-1.5 m kg *6490 *6490 *9460 5430 5540 3000 3960 2220 5.66
(-4.9 ft) lb *14310 *14310 *20860 11970 12210 6610 8730 4890 (18.6)
-3.0 m kg *6990 5610 *4600 3270 4.37
(-9.8 ft) lb *15410 12370 *10140 7210 (14.3)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause surious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

1-24
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HW140A
BOOM 4600 2450 2200 - 500 - Down - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 1.5 m (4.9 ft) 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) Capacity Reach
height (A)
m (ft)
7.5 m kg *2890 *2890 4.16
(24.6 ft) lb *6370 *6370 (13.6)
6.0 m kg *3880 *3880 *2390 *2390 5.70
(19.7 ft) lb *8550 *8550 *5270 *5270 (18.7)
4.5 m kg *4330 3940 *3790 2490 *2250 2140 6.55
(14.8 ft) lb *9550 8690 *8360 5490 *4960 4720 (21.5)
3.0 m kg *7850 6880 *5330 3710 3790 2410 *2260 1890 6.97
(9.8 ft) lb *17310 15170 *11750 8180 8360 5310 *4980 4170 (22.9)
1.5 m kg *5690 *5690 5700 3470 3670 2300 *2410 1810 7.05
(4.9 ft) lb *12540 *12540 12570 7650 8090 5070 *5310 3990 (23.1)
0.0 m kg *6760 6030 5530 3320 3590 2230 *2740 1880 6.79
(0.0 ft) lb *14900 13290 12190 7320 7910 4920 *6040 4140 (22.3)
-1.5 m kg *5600 *5600 *9980 6050 5490 3290 3590 2230 *3430 2150 6.16
(-4.9 ft) lb *12350 *12350 *22000 13340 12100 7250 7910 4920 *7560 4740 (20.2)
-3.0 m kg *7990 6200 *5350 3370 *4450 2930 5.01
(-9.8 ft) lb *17610 13670 *11790 7430 *9810 6460 (16.4)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause surious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

1-25
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HW140A
BOOM 4600 2450 2200 - 500 - Up - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 1.5 m (4.9 ft) 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) Capacity Reach
height (A)
m (ft)
7.5 m kg *2890 *2890 4.16
(24.6 ft) lb *6370 *6370 (13.6)
6.0 m kg *3880 3700 *2390 *2390 5.70
(19.7 ft) lb *8550 8160 *5270 *5270 (18.7)
4.5 m kg *4330 3580 *3790 2260 *2250 1940 6.55
(14.8 ft) lb *9550 7890 *8360 4980 *4960 4280 (21.5)
3.0 m kg *7850 6130 *5330 3360 3790 2180 *2260 1710 6.97
(9.8 ft) lb *17310 13510 *11750 7410 8360 4810 *4980 3770 (22.9)
1.5 m kg *5690 5510 5700 3120 3670 2080 *2410 1630 7.05
(4.9 ft) lb *12540 12150 12570 6880 8090 4590 *5310 3590 (23.1)
0.0 m kg *6760 5320 5530 2980 3590 2010 *2740 1690 6.79
(0.0 ft) lb *14900 11730 12190 6570 7910 4430 *6040 3730 (22.3)
-1.5 m kg *5600 *5600 *9980 5330 5490 2940 3590 2000 *3430 1940 6.16
(-4.9 ft) lb *12350 *12350 *22000 11750 12100 6480 7910 4410 *7560 4280 (20.2)
-3.0 m kg *7990 5480 *5350 3020 *4450 2640 5.01
(-9.8 ft) lb *17610 12080 *11790 6660 *9810 5820 (16.4)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause surious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

1-26
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HW140A
BOOM 4600 2600 2200 - 500 - Down - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 1.5 m (4.9 ft) 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) Capacity Reach
height (A)
m (ft)
7.5 m kg *2660 *2660 4.40
(24.6 ft) lb *5860 *5860 (14.4)
6.0 m kg *2230 *2230 5.87
(19.7 ft) lb *4920 *4920 (19.3)
4.5 m kg *4180 3970 *3720 2510 *2100 2070 6.70
(14.8 ft) lb *9220 8750 *8200 5530 *4630 4560 (22.0)
3.0 m kg *7510 6950 *5190 3730 3800 2420 *2110 1830 7.12
(9.8 ft) lb *16560 15320 *11440 8220 8380 5340 *4650 4030 (23.3)
1.5 m kg *6430 6250 5710 3480 3680 2310 *2250 1760 7.19
(4.9 ft) lb *14180 13780 12590 7670 8110 5090 *4960 3880 (23.6)
0.0 m kg *6820 6020 5520 3320 3590 2230 *2540 1820 6.94
(0.0 ft) lb *15040 13270 12170 7320 7910 4920 *5600 4010 (22.8)
-1.5 m kg *5360 *5360 *10110 6010 5470 3270 3570 2210 *3140 2070 6.33
(-4.9 ft) lb *11820 *11820 *22290 13250 12060 7210 7870 4870 *6920 4560 (20.8)
-3.0 m kg *9520 *9520 *8270 6150 5550 3340 *4400 2760 5.21
(-9.8 ft) lb *20990 *20990 *18230 13560 12240 7360 *9700 6080 (17.1)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause surious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

1-27
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HW140A
BOOM 4600 2600 2200 - 500 - Up - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 1.5 m (4.9 ft) 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) Capacity Reach
height (A)
m (ft)
7.5 m kg *2660 *2660 4.40
(24.6 ft) lb *5860 *5860 (14.4)
6.0 m kg *2230 *2230 5.87
(19.7 ft) lb *4920 *4920 (19.3)
4.5 m kg *4180 3610 *3720 2280 *2100 1870 6.70
(14.8 ft) lb *9220 7960 *8200 5030 *4630 4120 (22.0)
3.0 m kg *7510 6200 *5190 3380 3800 2190 *2110 1660 7.12
(9.8 ft) lb *16560 13670 *11440 7450 8380 4830 *4650 3660 (23.3)
1.5 m kg *6430 5530 5710 3130 3680 2080 *2250 1580 7.19
(4.9 ft) lb *14180 12190 12590 6900 8110 4590 *4960 3480 (23.6)
0.0 m kg *6820 5300 5520 2970 3590 2000 *2540 1640 6.94
(0.0 ft) lb *15040 11680 12170 6550 7910 4410 *5600 3620 (22.8)
-1.5 m kg *5360 *5360 *10110 5300 5470 2930 3570 1990 *3140 1860 6.33
(-4.9 ft) lb *11820 *11820 *22290 11680 12060 6460 7870 4390 *6920 4100 (20.8)
-3.0 m kg *9520 *9520 *8270 5430 5550 3000 *4400 2480 5.21
(-9.8 ft) lb *20990 *20990 *18230 11970 12240 6610 *9700 5470 (17.1)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause surious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

1-28
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HW140A
BOOM 4600 3100 2200 - 500 - Down - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 1.5 m (4.9 ft) 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) 7.5 m (24.6 ft) Capacity Reach
height (A)
m (ft)

7.5 m kg *2150 *2150 5.13

(24.6 ft) lb *4740 *4740 (16.8)
6.0 m kg *2670 2570 *1860 *1860 6.43
(19.7 ft) lb *5890 5670 *4100 *4100 (21.1)
4.5 m kg *3310 2530 *1770 *1770 7.20
(14.8 ft) lb *7300 5580 *3900 *3900 (23.6)
3.0 m kg *6350 *6350 *4690 3800 3820 2430 *2090 1680 *1790 1650 7.58
(9.8 ft) lb *14000 *14000 *10340 8380 8420 5360 *4610 3700 *3950 3640 (24.9)
1.5 m kg *9370 6410 5760 3520 3680 2310 *2510 1640 *1900 1580 7.65
(4.9 ft) lb *20660 14130 12700 7760 8110 5090 *5530 3620 *4190 3480 (25.1)
0.0 m kg *7170 6030 5530 3320 3570 2210 *2120 1630 7.42
(0.0 ft) lb *15810 13290 12190 7320 7870 4870 *4670 3590 (24.3)
-1.5 m kg *4710 *4710 *9570 5960 5430 3230 3530 2170 *2570 1810 6.85
(-4.9 ft) lb *10380 *10380 *21100 13140 11970 7120 7780 4780 *5670 3990 (22.5)
-3.0 m kg *7920 *7920 *9090 6040 5460 3260 *3610 2300 5.84
(-9.8 ft) lb *17460 *17460 *20040 13320 12040 7190 *7960 5070 (19.1)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause surious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

1-29
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HW140A
BOOM 4600 3100 2200 - 500 - Up - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 1.5 m (4.9 ft) 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) 7.5 m (24.6 ft) Capacity Reach
height (A)
m (ft)

7.5 m kg *2150 *2150 5.13

(24.6 ft) lb *4740 *4740 (16.8)
6.0 m kg *2670 2340 *1860 *1860 6.43
(19.7 ft) lb *5890 5160 *4100 *4100 (21.1)
4.5 m kg *3310 2300 *1770 1670 7.20
(14.8 ft) lb *7300 5070 *3900 3680 (23.6)
3.0 m kg *6350 *6350 *4690 3440 3820 2200 *2090 1520 *1790 1490 7.58
(9.8 ft) lb *14000 *14000 *10340 7580 8420 4850 *4610 3350 *3950 3280 (24.9)
1.5 m kg *9370 5680 5760 3170 3680 2080 *2510 1470 *1900 1420 7.65
(4.9 ft) lb *20660 12520 12700 6990 8110 4590 *5530 3240 *4190 3130 (25.1)
0.0 m kg *7170 5320 5530 2970 3570 1980 *2120 1460 7.42
(0.0 ft) lb *15810 11730 12190 6550 7870 4370 *4670 3220 (24.3)
-1.5 m kg *4710 *4710 *9570 5240 5430 2890 3530 1940 *2570 1630 6.85
(-4.9 ft) lb *10380 *10380 *21100 11550 11970 6370 7780 4280 *5670 3590 (22.5)
-3.0 m kg *7920 *7920 *9090 5320 5460 2920 *3610 2060 5.84
(-9.8 ft) lb *17460 *17460 *20040 11730 12040 6440 *7960 4540 (19.1)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause surious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

1-30
 3) 4.71 m 2-PIECE BOOM+2200 kg COUNTERWEIGHT

Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger

2-PIECE Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HW140A
BOOM 4710 2000 2200 - 500 - Down - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) Capacity Reach
height (A)
m (ft)
7.5 m kg *4410 *4410 3.69
(24.6 ft) lb *9720 *9720 (12.1)
6.0 m kg *4210 4020 *3470 2970 5.37
(19.7 ft) lb *9280 8860 *7650 6550 (17.6)
4.5 m kg *5800 *5800 *4630 3890 3870 2460 *3200 2280 6.26
(14.8 ft) lb *12790 *12790 *10210 8580 8530 5420 *7050 5030 (20.6)
3.0 m kg *5580 3650 3780 2390 3170 2000 6.71
(9.8 ft) lb *12300 8050 8330 5270 6990 4410 (22.0)
1.5 m kg 5670 3420 3680 2300 3070 1920 6.79
(4.9 ft) lb 12500 7540 8110 5070 6770 4230 (22.3)
0.0 m kg *4830 *4830 5540 3310 3620 2240 3220 2010 6.52
(0.0 ft) lb *10650 *10650 12210 7300 7980 4940 7100 4430 (21.4)
-1.5 m kg *9500 6110 5540 3310 3780 2340 5.86
(-4.9 ft) lb *20940 13470 12210 7300 8330 5160 (19.2)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause surious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

1-31
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
2-PIECE Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HW140A
BOOM 4710 2000 2200 - 500 - Up - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) Capacity Reach
height (A)
m (ft)
7.5 m kg *4410 *4410 3.69
(24.6 ft) lb *9720 *9720 (12.1)
6.0 m kg *4210 3650 *3470 2690 5.37
(19.7 ft) lb *9280 8050 *7650 5930 (17.6)
4.5 m kg *5800 *5800 *4630 3530 3870 2230 *3200 2060 6.26
(14.8 ft) lb *12790 *12790 *10210 7780 8530 4920 *7050 4540 (20.6)
3.0 m kg *5580 3290 3780 2160 3170 1810 6.71
(9.8 ft) lb *12300 7250 8330 4760 6990 3990 (22.0)
1.5 m kg 5670 3070 3680 2070 3070 1730 6.79
(4.9 ft) lb 12500 6770 8110 4560 6770 3810 (22.3)
0.0 m kg *4830 *4830 5540 2960 3620 2010 3220 1810 6.52
(0.0 ft) lb *10650 *10650 12210 6530 7980 4430 7100 3990 (21.4)
-1.5 m kg *9500 5380 5540 2960 3780 2110 5.86
(-4.9 ft) lb *20940 11860 12210 6530 8330 4650 (19.2)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause surious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

1-32
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
2-PIECE Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HW140A
BOOM 4710 2450 2200 - 500 - Down - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) Capacity Reach
height (A)
m (ft)
7.5 m kg *3030 *3030 4.46
(24.6 ft) lb *6680 *6680 (14.6)
6.0 m kg *3710 *3710 *2500 *2500 5.92
(19.7 ft) lb *8180 *8180 *5510 *5510 (19.4)
4.5 m kg *4190 3950 *3880 2490 *2320 2030 6.74
(14.8 ft) lb *9240 8710 *8550 5490 *5110 4480 (22.1)
3.0 m kg *5190 3690 3800 2400 *2300 1800 7.15
(9.8 ft) lb *11440 8140 8380 5290 *5070 3970 (23.5)
1.5 m kg 5690 3440 3670 2280 *2410 1730 7.23
(4.9 ft) lb 12540 7580 8090 5030 *5310 3810 (23.7)
0.0 m kg *5270 *5270 5520 3290 3590 2210 *2670 1800 6.98
(0.0 ft) lb *11620 *11620 12170 7250 7910 4870 *5890 3970 (22.9)
-1.5 m kg *9410 6000 5480 3250 3580 2200 *3220 2050 6.37
(-4.9 ft) lb *20750 13230 12080 7170 7890 4850 *7100 4520 (20.9)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause surious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

1-33
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
2-PIECE Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HW140A
BOOM 4710 2450 2200 - 500 - Up - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) Capacity Reach
height (A)
m (ft)
7.5 m kg *3030 *3030 4.46
(24.6 ft) lb *6680 *6680 (14.6)
6.0 m kg *3710 *3710 *2500 2310 5.92
(19.7 ft) lb *8180 *8180 *5510 5090 (19.4)
4.5 m kg *4190 3580 *3880 2260 *2320 1830 6.74
(14.8 ft) lb *9240 7890 *8550 4980 *5110 4030 (22.1)
3.0 m kg *5190 3330 3800 2160 *2300 1620 7.15
(9.8 ft) lb *11440 7340 8380 4760 *5070 3570 (23.5)
1.5 m kg 5690 3080 3670 2060 *2410 1550 7.23
(4.9 ft) lb 12540 6790 8090 4540 *5310 3420 (23.7)
0.0 m kg *5270 5250 5520 2940 3590 1980 *2670 1610 6.98
(0.0 ft) lb *11620 11570 12170 6480 7910 4370 *5890 3550 (22.9)
-1.5 m kg *9410 5280 5480 2900 3580 1970 *3220 1840 6.37
(-4.9 ft) lb *20750 11640 12080 6390 7890 4340 *7100 4060 (20.9)
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause surious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

1-34
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
2-PIECE Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HW140A
BOOM 4710 2600 2200 - 500 - Down - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) Capacity Reach
height (A)
m (ft)
7.5 m kg *3340 *3340 *2790 *2790 4.70
(24.6 ft) lb *7360 *7360 *6150 *6150 (15.4)
6.0 m kg *3560 *3560 *2730 2520 *2330 *2330 6.10
(19.7 ft) lb *7850 *7850 *6020 5560 *5140 *5140 (20.0)
4.5 m kg *4050 3980 *3770 2510 *2170 1960 6.90
(14.8 ft) lb *8930 8770 *8310 5530 *4780 4320 (22.6)
3.0 m kg *7450 6900 *5050 3710 3810 2400 *2150 1750 7.30
(9.8 ft) lb *16420 15210 *11130 8180 8400 5290 *4740 3860 (23.9)
1.5 m kg 5700 3440 3680 2290 *2250 1680 7.37
(4.9 ft) lb 12570 7580 8110 5050 *4960 3700 (24.2)
0.0 m kg *5350 *5350 5510 3280 3580 2200 *2480 1740 7.13
(0.0 ft) lb *11790 *11790 12150 7230 7890 4850 *5470 3840 (23.4)
-1.5 m kg *9050 5960 5460 3240 3570 2190 *2970 1970 6.53
(-4.9 ft) lb *19950 13140 12040 7140 7870 4830 *6550 4340 (21.4)
-3.0 m kg 5550 3310
(-9.8 ft) lb 12240 7300
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause surious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

1-35
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
2-PIECE Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HW140A
BOOM 4710 2600 2200 - 500 - Up - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) Capacity Reach
height (A)
m (ft)
7.5 m kg *3340 *3340 *2790 *2790 4.70
(24.6 ft) lb *7360 *7360 *6150 *6150 (15.4)
6.0 m kg *3560 *3560 *2730 2280 *2330 2210 6.10
(19.7 ft) lb *7850 *7850 *6020 5030 *5140 4870 (20.0)
4.5 m kg *4050 3610 *3770 2270 *2170 1770 6.90
(14.8 ft) lb *8930 7960 *8310 5000 *4780 3900 (22.6)
3.0 m kg *7450 6140 *5050 3350 3810 2170 *2150 1570 7.30
(9.8 ft) lb *16420 13540 *11130 7390 8400 4780 *4740 3460 (23.9)
1.5 m kg 5700 3090 3680 2060 *2250 1510 7.37
(4.9 ft) lb 12570 6810 8110 4540 *4960 3330 (24.2)
0.0 m kg *5350 5230 5510 2930 3580 1980 *2480 1560 7.13
(0.0 ft) lb *11790 11530 12150 6460 7890 4370 *5470 3440 (23.4)
-1.5 m kg *9050 5240 5460 2890 3570 1960 *2970 1760 6.53
(-4.9 ft) lb *19950 11550 12040 6370 7870 4320 *6550 3880 (21.4)
-3.0 m kg 5550 2960
(-9.8 ft) lb 12240 6530
Note 1. Lifting capacity are based on ISO 10567.
2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause surious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

1-36
6. BUCKET SELECTION GUIDE
1) MONO BOOM, 1700 kg COUNTERWEIGHT

General bucket Heavy duty Ditch cleaning Slope finishing Hammerless tooth

MONO
Capacity Width
Recommendation mm (ft-in)
Without With Weight Tooth
SAE CECE 4.6 m (15' 1")
Type side side
Heaped heaped Boom
cutter cutter
2.0 m 2.45 m 2.6 m 3.1 m
m3 m3 mm mm kg
EA (6' 7') (8' 0") (8' 6") (10' 2')
(yd3) (yd3) (in) (in) (lb)
Arm Arm Arm Arm
0.58 0.50 950 1110 480
(0.76) (0.65) (37.4'') (43.7'') (1060)
5 ◐ ■ ▲ ▲
General 0.52 0.45 870 1020 460
bucket (0.68) (0.59) (34.3'') (40.2'') (1010)
5 ◐ ■ ■ ▲
0.65 0.55 1060 1210 513
(0.85) (0.72) (41.7'') (47.6'') (1130)
5 ■ ▲ ■ X
Heavy 0.71 0.60 1140 1300 536
duty (0.93) (0.78) (44.9'') (51.2'') (1180)
5 ▲ ▲ X X
Ditch 0.45 0.40 1520 410
- 0 ● ● ◐ ■
cleaning (0.59) (0.52) (59.8'') (900)
Slope 0.55 0.45 1800 585
finishing (0.72) (0.59) (70.9'')
-
(1290)
0 ◐ ■ ▲ ▲
0.50 0.45 762 821 439
Hammer 4 ● ◐ ■ ■
(0.65) (0.59) (30.0'') (32.3'') (970)
-less
0.61 0.54 914 974 490
tooth
(0.80) (0.71) (36.0'') (38.3'') (1080)
5 ■ ▲ ▲ ▲

● Applicable for materials with density of 2100 kg/m3 (3500 lb/yd3) or less
◐ Applicable for materials with density of 1800 kg/m3 (3000 lb/yd3) or less
■ Applicable for materials with density of 1500 kg/m3 (2500 lb/yd3) or less
▲ Applicable for materials with density of 1200 kg/m3 (2000 lb/yd3) or less
X Not recommended
※ These recommendations are for general conditions and average use.
Work tools and ground conditions have effects on machine performance.
Select an optimum combination according to the working conditions and the type of work that is
being done.
Consult your HD Hyundai Construction Equipment dealer for information on selecting the
correct boom-arm
boom arm-bucket
bucket combination.

1-37
 2) MONO BOOM, 2200 kg COUNTERWEIGHT

General bucket Heavy duty Ditch cleaning Slope finishing Hammerless tooth

MONO
Capacity Width
Recommendation mm (ft-in)
Without With Weight Tooth
SAE CECE 4.6 m (15' 1")
Type side side
Heaped heaped Boom
cutter cutter
2.0 m 2.45 m 2.6 m 3.1 m
m3 m3 mm mm kg
EA (6' 7') (8' 0") (8' 6") (10' 2')
(yd3) (yd3) (in) (in) (lb)
Arm Arm Arm Arm
0.58 0.50 950 1110 480
(0.76) (0.65) (37.4'') (43.7'') (1060)
5 ◐ ◐ ■ ▲
General 0.52 0.45 870 1020 460
5 ● ◐ ◐ ■
bucket (0.68) (0.59) (34.3'') (40.2'') (1010)
0.65 0.55 1060 1210 513
(0.85) (0.72) (41.7'') (47.6'') (1130)
5 ◐ ■ ■ ▲
Heavy 0.71 0.60 1140 1300 536
duty (0.93) (0.78) (44.9'') (51.2'') (1180)
5 ■ ▲ ▲ X
Ditch 0.45 0.40 1520 410
- 0 ● ● ● ◐
cleaning (0.59) (0.52) (59.8'') (900)
Slope 0.55 0.45 1800 585
finishing (0.72) (0.59) (70.9'')
-
(1290)
0 ◐ ■ ■ ▲
0.50 0.45 762 821 439
Hammer 4 ● ● ◐ ■
(0.65) (0.59) (30.0'') (32.3'') (970)
-less
0.61 0.54 914 974 490
tooth
(0.80) (0.71) (36.0'') (38.3'') (1080)
5 ◐ ■ ■ ▲

● Applicable for materials with density of 2100 kg/m3 (3500 lb/yd3) or less
◐ Applicable for materials with density of 1800 kg/m3 (3000 lb/yd3) or less
■ Applicable for materials with density of 1500 kg/m3 (2500 lb/yd3) or less
▲ Applicable for materials with density of 1200 kg/m3 (2000 lb/yd3) or less
X Not recommended
※ These recommendations are for general conditions and average use.
Work tools and ground conditions have effects on machine performance.
Select an optimum combination according to the working conditions and the type of work that is
being done.
Consult your HD Hyundai Construction Equipment dealer for information on selecting the
correct boom-arm
boom arm-bucket
bucket combination.

1-38
 3) 2-PIECE BOOM, 2200 kg COUNTERWEIGHT

General bucket Heavy duty Ditch cleaning Slope finishing Hammerless tooth

2-PIECE
Capacity Width
Recommendation mm (ft-in)
Without With Weight Tooth
SAE CECE
Type side side 4.71 m (15' 5") Boom
Heaped heaped
cutter cutter
2.0 m 2.45 m 2.6 m
m3 m3 mm mm kg
EA (6' 7') (8' 0") (8' 6')
(yd3) (yd3) (in) (in) (lb)
Arm Arm Arm
0.58 0.50 950 1110 480
5 ◐ ■ ■
(0.76) (0.65) (37.4'') (43.7'') (1060)
General 0.52 0.45 870 1020 460
5 ● ◐ ◐
bucket (0.68) (0.59) (34.3'') (40.2'') (1010)
0.65 0.55 1060 1210 513
(0.85) (0.72) (41.7'') (47.6'') (1130)
5 ■ ▲ ▲
Heavy 0.71 0.60 1140 1300 536
duty (0.93) (0.78) (44.9'') (51.2'') (1180)
5 ■ ▲ ▲
Ditch 0.45 0.40 1520 410
- 0 ● ● ●
cleaning (0.59) (0.52) (59.8'') (900)
Slope 0.55 0.45 1800 585
- 0 ◐ ■ ■
finishing (0.72) (0.59) (70.9'') (1290)
0.50 0.45 762 821 439
Hammer 4 ● ◐ ◐
(0.65) (0.59) (30.0'') (32.3'') (970)
-less
tooth 0.61 0.54 914 974 490
5 ◐ ■ ■
(0.80) (0.71) (36.0'') (38.3'') (1080)

● Applicable for materials with density of 2100 kg/m3 (3500 lb/yd3) or less
◐ Applicable for materials with density of 1800 kg/m3 (3000 lb/yd3) or less
■ Applicable for materials with density of 1500 kg/m3 (2500 lb/yd3) or less
▲ Applicable for materials with density of 1200 kg/m3 (2000 lb/yd3) or less
X Not recommended
※ These recommendations are for general conditions and average use.
Work tools and ground conditions have effects on machine performance.
Select an optimum combination according to the working conditions and the type of work that is
being done.
Consult your HD Hyundai Construction Equipment dealer for information on selecting the
correct boom-arm
boom arm-bucket
bucket combination.

1-39
7. SPECIFICATIONS FOR MAJOR COMPONENTS
1) ENGINE

Item Specification
Maker / Model CUMMINS / B4.5
4-cycle, turbocharged, charge air cooled,
Type
electronic controlled diesel engine
Cooling method Water cooled
Number of cylinders and arrangement 4 cylinders, in-line
Firing order 1-3-4-2
Combustion chamber type Direct injection type
Cylinder bore×stroke 107×124 mm (4.21"×4.88")
Displacement 4.5ℓ(275 cu in)
Compression ratio 17.2 : 1
Gross power 173 Hp (129 kW ) at 2200 rpm
Net power 170 Hp (127 kW) at 2200 rpm
Max. power 173 Hp (129 kW) at 2200 rpm
Peak Torque 780 N·m (575 lb·ft) at 1,500 rpm
Engine oil quantity 11ℓ(2.9 U.S. gal)
Wet weight or Dry weight 378 kg (830 lb)
Starter motor 24 V-4.8 kW
Alternator 24 V-95 A

2) MAIN PUMP
Item Specification
Type Variable displacement piston pump
Capacity 145 cc/rev
Maximum pressure 350 kgf/cm2 (4980 psi) [380 kgf/cm2 (5400 psi)]
Rated oil flow 230ℓ/min (60.8 U.S. gpm / 50.6 U.K. gpm)
Rated rpm 1600 rpm
[ ]: Power boost

1-40
 3) STEERING PUMP

Item Specification
Type Fixed displacement gear pump single stage
Capacity 35 cc/rev
Maximum pressure 210 kgf/cm2 (2990 psi)
Rated oil flow 56ℓ/min (14.8 U.S. gpm/12.3 U.K. gpm)

4) MAIN CONTROL VALVE

Item Specification
Type Section block
Operating method Hydraulic pilot system
Main relief valve pressure 350 kgf/cm2 (4980 psi) [380 kgf/cm2 (5400 psi)]
Boom 420 kgf/cm2 (5970 psi)
Port relief valve pressure Arm 420 kgf/cm2 (5970 psi)
Bucket 420 kgf/cm2 (5970 psi)
[ ] : Power boost

5) SWING UNIT

Item Specification
Type Radial piston motor
Capacity 1534 cc/rev
Relief pressure 270 kgf/cm2 (3840 psi)
Braking system Automatic, spring applied hydraulic released
Brake release pressure 15~40 kgf/cm2 (213~569 psi) below
Reduction gear type -

6) TRAVEL MOTOR

Item Specification
Type Variable displacement bent-axis axial piston motor
Capacity 107/41 cc/rev
Relief pressure 380 kgf/cm2 (5400 psi)

1-41
 7) POWER TRAIN
Item Description Specification
Type 2 speed power shift transmission
1st 4.87
Transmission Gear ratio
2nd 1.20
Clutch pressure 30~32 kgf /cm2 (427~455 psi)
Type Multi disc brake integrated in transmission
Parking brake
Maximum braking torque 2464 kgf·m (17820 lbf·ft)
Type 4 wheel drive with differential
Gear ratio 16.0
Axle Brake Multi disc brake
Brake pressure 81.6 kgf /cm2 (1160 psi)
Steering pressure 180 kgf /cm2 (2560 psi)

8) POWER TRAIN GEAR PUMP

Item Description

Capacity Steering + brake : 11.9 + 19.3 cc / rev (pump PTO)

Steering + brake : 18 + 29 lpm (pump PTO)

Rated flow
(4.8 + 7.7 U.S. gpm / 4.0 + 6.4 U.K. gpm)

1-42
 9) CYLINDER

Item Specification
Bore dia×Stroke Ø105 × 1105 mm
Boom cylinder
Cushion Extend only
Bore dia×Stroke Ø115 × 1138 mm
Arm cylinder
Cushion Extend and retract
Bore dia×Stroke Ø105 × 992 mm
Arm cylinder (2-piece boom)
Cushion Extend only
Bore dia×Stroke Ø145 × 634 mm
Adjust cylinder (2-piece boom)
Cushion -
Bore dia×Stroke Ø100 × 850 mm
Bucket cylinder
Cushion Extend only
Bore dia×Stroke Ø100 × 241 mm
Dozer cylinder (front, rear)
Cushion -
Bore dia×Stroke Ø110 × 446 mm
Outrigger cylinder
Cushion -
※ Discoloration of cylinder rod can occur when the friction reduction additive of lubrication oil spreads on
the rod surface.
※ Discoloration does not cause any harmful effect on the cylinder performance.

1-43
8. RECOMMENDED OILS

HD Hyundai Construction Equipment genuine lubricating oils have been developed to offer the best perfor-
mance and service life for your equipment. These oils have been tested according to the specifications of HD
Hyundai Construction Equipment and, therefore, will meet the highest safety and quality requirements.
We recommend that you use only HD Hyundai Construction Equipment genuine lubricating oils and grease
officially approved by HD Hyundai Construction Equipment.
Ambient temperature˚C(˚F)
Capacity
Service point Kind of fluid -50 -30 -20 -10 0 10 20 30 40
ℓ (U.S. gal)
(-58) (-22) (-4) (14) (32) (50) (68) (86) (104)
★SAE 5W-40
Engine
11 (2.9) SAE 30
oil pan
Engine oil SAE 10W
Transmission SAE 10W-30
2.5 (0.66)
case SAE 15W-40
Mixture of
DEF/
urea and
AdBlue® 48 (12.7) ISO 22241, High-purity urea + deionized water (32.5:67.5)
deionized
tank
water

Front axle Center : 9.0 (2.38)

Hub : 2.4×2 (0.63×2)
Gear oil SAE 85W-90 LSD or UTTO
Center : 11.2 (2.96)
Rear axle Hub : 2.4×2 (0.63×2)
★ISO VG 15
Tank:
Hydraulic 122 (32.2) ISO VG 32
Hydraulic oil
tank System: ISO VG 46, HBHO★3
204 (53.9) ISO VG 68

★ASTM D975 NO.1

Fuel tank Diesel fuel★1 250 (66.0)
ASTM D975 NO.2

Fitting ★NLGI NO.1

(Grease Grease As required
nipple) NLGI NO.2
Mixture of
Radiator Ethylene glycol base permanent type (50 : 50)
antifreeze
(Reservoir 23 (3.1)
and soft ★Ethylene glycol base permanent type (60 : 40)
tank)
water★2
SAE : Society of Automotive Engineers ★ : Cold region (Russia, CIS, Mongolia)
API : American Petroleum Institute ★1 : Ultra low sulfur diesel
ISO : International Organization for Standardization - sulfur content  10 ppm
NLGI : National Lubricating Grease Institute ★2 : Soft water
ASTM : American Society of Testing and Materia
City water or distilled water
DEF : Diesel Exhaust Fluid, DEF compatible with AdBlue®
★3 : HD Hyundai Construction
Equipment Bio Hydraulic Oil
※ Using any lubricating oils other than HD Hyundai Construction Equipment genuine products may lead to a
deterioration of performance and cause damage to major components.
※ Do not mix HD Hyundai Construction Equipment genuine oil with any other lubricating oil as it may result in
damage to the systems of major components.
※ Do not use any engine oil other than that specified above, as it may clog the diesel particulate filter(DPF).
※ For HD Hyundai Construction Equipment genuine lubricating oils and grease for use in regions with extremely
low temperatures, please contact your local HD Hyundai Construction Equipment dealers.
1-44