2004-2006-VA-Powertrain

TABLE OF CONTENTS
1.0 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1.1 SYSTEM COVERAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

1.2 SIX-STEP TROUBLESHOOTING PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . .1
2.0 IDENTIFICATION OF SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
3.0 SYSTEM DESCRIPTION AND FUNCTIONAL OPERATION . . . . . . . . . . . . . . . . . . . . . .1
3.1 GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

3.2 FUNCTIONAL OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
3.2.1 ECM ON-BOARD DIAGNOSTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
3.2.2 ECM OPERATING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
3.2.3 MONITORED CIRCUITS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
3.2.4 SKREEM OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
3.2.5 SKREEM ON-BOARD DIAGNOSTICS. . . . . . . . . . . . . . . . . . . . . . . . . . .2
3.2.6 SKREEM OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
3.3 DIAGNOSTIC TROUBLE CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
3.3.1 HARD CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
3.3.2 INTERMITTENT CODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
3.3.3 ECM DIAGNOSTIC TROUBLE CODES. . . . . . . . . . . . . . . . . . . . . . . . . .3
3.3.4 HANDLING NO TROUBLE CODE PROBLEMS . . . . . . . . . . . . . . . . . . .8
3.4 USING THE DRBIIIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
3.4.1 DRBIIIT DOES NOT POWER UP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
3.4.2 DISPLAY IS NOT VISIBLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
4.0 DISCLAIMERS, SAFETY, WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
4.1 DISCLAIMERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
4.2 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
4.2.1 TECHNICIAN SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . .8
4.2.2 VEHICLE PREPARATION FOR TESTING. . . . . . . . . . . . . . . . . . . . . . . .9
4.2.3 SERVICING SUB-ASSEMBLIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
4.2.4 DRBIIIT SAFETY INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
4.3 WARNINGS AND CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
4.3.1 ROAD TEST WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
4.3.2 VEHICLE DAMAGE CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
5.0 REQUIRED TOOLS AND EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
6.0 GLOSSARY OF TERMS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
7.0 DIAGNOSTIC INFORMATION AND PROCEDURES . . . . . . . . . . . . . . . . . . . . . . . . . . .11
COMMUNICATION
*NO RESPONSE FROM ENGINE CONTROL MODULE . . . . . . . . . . . . . . . . . . . . . . . .12
*NO RESPONSE FROM SENTRY KEY REMOTE ENTRY MODULE . . . . . . . . . . . . . .14
DRIVEABILITY - DIESEL
P-1105 ATMOSPHERIC PRESSURE SENSOR PLAUSIBILITY WITH BOOST
PRESSURE SENSOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
P1105-ATMOSPHERIC PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH . . . . . .16
P1105-ATMOSPHERIC PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW . . . . . .16
P1617- ECM READ/WRITE ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
i
TABLE OF CONTENTS - Continued
P1617- ECM WRITE ERROR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
P1617-ECM INCORRECT VALUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
P1617-ECM READ ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
P2122-INTERNAL ERROR COUNTER FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
P2122-INTERNAL ERROR ENGINE SHUT OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
P2122-INTERNAL ERROR ENGINE VOLTAGE MONITORING . . . . . . . . . . . . . . . . . . .16
P2122-INTERNAL ERROR ENGINE VOLTAGE MONITORING . . . . . . . . . . . . . . . . . . .16
P2123-INJECTOR BANK ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
P2124-INJECTOR BANK ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
P2139-ECM INJECTOR OUTPUT STAGE #1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
P2139-ECM INJECTOR OUTPUT STAGE #1 SHORT CIRCUIT . . . . . . . . . . . . . . . . . .16
P2140-ECM INJECTOR OUTPUT STAGE #2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
P2140-ECM INJECTOR OUTPUT STAGE #2 SHORT CIRCUIT . . . . . . . . . . . . . . . . . .16
P2149-ECM A/D CONVERTER HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
P2149-ECM A/D CONVERTER LOW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
P2149-ECM A/D CONVERTER PLAUSIBILITY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
P2153-STARTER RELAY CIRCUIT ECM THERMAL OVERLOAD . . . . . . . . . . . . . . . .16
P2197-FUEL QUANTITY SOLENOID ECM THERMAL OVERLOAD . . . . . . . . . . . . . . .16
P2214-CAN MESSAGE ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
P2319-ECM INTERNAL ERROR 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
P2323-ECM INTERNAL ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
P2324-ECM INJECTOR MONITORING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
P2324-ECM INJECTOR UNDERVOLTAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
P2340-ECM INJECTION QUANTITY ERROR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
P2350-INTERNAL VOLTAGE ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
P2352-INJECTION FAULT - EXCESSIVE TEMPERATURE . . . . . . . . . . . . . . . . . . . . . .17
P2352-INJECTION FAULT - QUANTITY ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
P2352-INJECTION FAULT - TORQUE LIMIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
P2352-INJECTION FAULT EXCESSIVE ENGINE SPEED . . . . . . . . . . . . . . . . . . . . . . .17
P2354-ECM INTERNAL FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
P2500-FUEL PRESSURE SOLENOID CIRCUIT EXCESSIVE CURRENT . . . . . . . . . .17
P2514-CRANKCASE VENT HEATER EXCESSIVE CURRENT . . . . . . . . . . . . . . . . . . .17
P2526-BOOST PRESSURE SERVO MOTOR EXCESSIVE CURRENT . . . . . . . . . . . .17
P2527-EGR VALVE EXCESSIVE CURRENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
P0100-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW . . . . . . . . . . . . . . .19
ii
P2011-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO HIGH . . . . . . . . .19
P2011-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO LOW . . . . . . . . . .19
P2024-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO HIGH . . . . . . . . . . . . . . .19
P2065-MASS AIR FLOW SENSOR SUPPLY VOLTAGE TOO HIGH. . . . . . . . . . . . . . .19
P2065-MASS AIR FLOW SENSOR SUPPLY VOLTAGE TOO LOW . . . . . . . . . . . . . . .19
P2067-MASS AIR FLOW SENSOR SIGNAL CIRCUIT OPEN OR SHORTED . . . . . . .19
P2067-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO HIGH . . . . . . . . . . . . . . .19
P2068-MASS AIR FLOW SENSOR PLAUSIBILITY SIGNAL RATIO ERROR . . . . . . . .19
P2633-MAF SENSOR SIGNAL PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
P0105-INTAKE PRESSURE SENSOR CAN MESSAGE ERROR . . . . . . . . . . . . . . . . .25
P0105-INTAKE PRESSURE SENSOR PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . .25
P0105-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH. . . . . . . . . . . . .28
P0105-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW . . . . . . . . . . . . .31
P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO HIGH . . . . . . . . . . . . . .34
P2063-INTAKE AIR TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH . . . . . .34
P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO LOW. . . . . . . . . . . . . . .37
P2063-INTAKE AIR TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW . . . . . .37
P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT PLAUSIBILITY . . . . . . . . . . . . .40
P2012-ENGINE COOLANT TEMP SENSOR CIRCUIT PLAUSIBILITY . . . . . . . . . . . . .40
P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT PLAUSIBILITY WITH ENGINE
OIL SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO
HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
P0180-FUEL TEMPERATURE SENSOR CIRCUIT - SIGNAL VOLTAGE TOO HIGH. .49
P0180-FUEL TEMPERATURE SENSOR CIRCUIT - SIGNAL VOLTAGE TOO LOW . .51
P2625-FUEL TEMPERATURE SENSOR PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . .51
P0190-FUEL PRESS SENSOR CIRCUIT MALF SIGNAL VOLTAGE TOO HIGH . . . . .53
P2008-FUEL PRESSURE SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH . . . . . .53
P0190-FUEL PRESS SENSOR CIRCUIT MALF SIGNAL VOLTAGE TOO LOW . . . . .57
P2008-FUEL PRESSURE SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW . . . . . . .57
P0201-CYLINDER 1-INJECTOR CIRCUIT EXCESSIVE CURRENT . . . . . . . . . . . . . . .60
P0201-CYLINDER 1-INJECTOR CIRCUIT OPEN OR SHORTED TO GROUND . . . . .60
P0201-CYLINDER 1-INJECTOR CIRCUIT SHORTED TO GROUND . . . . . . . . . . . . . .60
P0201-CYLINDER 1-INJECTOR CIRCUIT SHORTED TO VOLTAGE . . . . . . . . . . . . . .60
iii
P2123-INJECTOR CIRCUIT FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
P2123-INJECTOR CIRCUIT LOW SIDE SHORTED TO GROUND . . . . . . . . . . . . . . . .60
P2123-INJECTOR CIRCUIT SHORTED TO GROUND OR VOLTAGE . . . . . . . . . . . . .60
P2124-INJECTOR CIRCUIT FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
P2124-INJECTOR CIRCUIT LOW SIDE SHORTED TO GROUND . . . . . . . . . . . . . . . .60
P2124-INJECTOR CIRCUIT SHORTED TO GROUND OR VOLTAGE . . . . . . . . . . . . .60
P2141-CYLINDER #1 INJECTOR OPEN CIRCUIT. . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
P0300-MISFIRE DETECTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
P2113-MISFIRE CYLINDER #1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
P2567-LEAKAGE CYLINDER #1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
P2573-GENERAL LEAKAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
P2574-INJECTOR 1 INJECTION TIME ABOVE LIMIT . . . . . . . . . . . . . . . . . . . . . . . . . .66
P2574-INJECTOR 1 INJECTION TIME BELOW LIMIT. . . . . . . . . . . . . . . . . . . . . . . . . .66
P0500-WHEEL SPEED SENSOR PLAUS - CAN BUS MESSAGE FROM ABS . . . . . .69
P0600-CAN DATA BUS - BUS CIRCUIT FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
P1222-ACC PEDAL POSITION SENSOR 1 CKT PLAUSIBILITY . . . . . . . . . . . . . . . . .73
P1222-ACC PEDAL POSITION SENSOR 1 CKT SIGNAL VOLTAGE TOO HIGH . . . .73
P1222-ACC PEDAL POSITION SENSOR 1 CKT SIGNAL VOLTAGE TOO LOW . . . .73
P1234-ACC PEDAL POSITION SENSOR 2 CIRCUIT PLAUSIBILITY. . . . . . . . . . . . . .73
P1234-ACC PEDAL POSITION SENSOR 2 CKT SIGNAL VOLTAGE TOO HIGH . . . .73
P1234-ACC PEDAL POSITION SENSOR 2 CKT SIGNAL VOLTAGE TOO LOW . . . .73
P2327-APP SENSOR PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
iv
P1480-GLOW PLUG INDICATOR ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
P1482-GLOW PLUG MODULE - COMMUNICATION ERROR. . . . . . . . . . . . . . . . . . . .80
P2537-GLOW PLUG CONTROL CIRCUIT PREGLOW FAULT . . . . . . . . . . . . . . . . . . .80
P2537-GLOW PLUG CONTROL CIRCUIT PREGLOW SHORT TO GROUND. . . . . . .80
P2537-GLOW PLUG CONTROL CIRCUIT PREGLOW SHORT TO VOLTAGE . . . . . .80
P1482-GLOW PLUG MODULE - EXCESS CURRENT. . . . . . . . . . . . . . . . . . . . . . . . . .82
P2133-GLOW PLUG #1 CIRCUIT EXCESSIVE CURRENT. . . . . . . . . . . . . . . . . . . . . .82
P2133-GLOW PLUG #1 CIRCUIT OPEN CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
P2133-GLOW PLUG #1 CIRCUIT SHORT TO GROUND . . . . . . . . . . . . . . . . . . . . . . .82
P2133-GLOW PLUG #1 CIRCUIT SHORT TO VOLTAGE . . . . . . . . . . . . . . . . . . . . . . .82
P1482-GLOW PLUG MODULE - INCORRECT TIMER . . . . . . . . . . . . . . . . . . . . . . . . .85
P1482-GLOW PLUG MODULE - INTERNAL FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . .85
P2538-GLOW PLUG MODULE COMMUNICATION ERROR . . . . . . . . . . . . . . . . . . . . .85
P2538-GLOW PLUG MODULE EXCESSIVE CURRENT ERROR. . . . . . . . . . . . . . . . .85
P2538-GLOW PLUG MODULE TIMER ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
P1610-ENGINE CONTROL RELAY PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
P1610-ENGINE CONTROL RELAY SHUTS OFF TOO EARLY . . . . . . . . . . . . . . . . . . .89
P1610-ENGINE CONTROL RELAY SHUTS OFF TOO LATE . . . . . . . . . . . . . . . . . . . .91
P1611-SENSOR SUPPLY 1 VOLTAGE IS TOO HIGH . . . . . . . . . . . . . . . . . . . . . . . . . .94
P1611-SENSOR SUPPLY 1 VOLTAGE IS TOO LOW . . . . . . . . . . . . . . . . . . . . . . . . . .96
P1612-IGNITION VOLTAGE - VOLTAGE ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
P1615-ECM VOLTAGE SUPPLY IS TOO HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
P1615-ECM VOLTAGE SUPPLY IS TOO LOW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
P1630-IMMOBILIZER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
P1630-IMMOBILIZER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
P1630-IMMOBILIZER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
P1630-IMMOBILIZER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
P2201-IMMOBILIZER CAN MESSAGE ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
P2243-NO MESSAGE RECEIVED FROM SKREEM . . . . . . . . . . . . . . . . . . . . . . . . . .102
P1681-ACM CIRCUIT FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
P1681-ACM CIRCUIT SHORT TO VOLTAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
P2009-WATER IN FUEL SENSOR - WATER IN FUEL. . . . . . . . . . . . . . . . . . . . . . . . .106
P2009-WATER IN FUEL SENSOR SIGNAL ERROR . . . . . . . . . . . . . . . . . . . . . . . . . .106
P2010-MASS AIR FLOW SENSOR NEGATIVE DEVIATION . . . . . . . . . . . . . . . . . . . .110
P2010-MASS AIR FLOW SENSOR POSITIVE DEVIATION . . . . . . . . . . . . . . . . . . . . .110
P2068-MASS AIR FLOW SENSOR PLAUSIBILITY SIGNAL RATIO TOO LARGE . . .110
P2068-MASS AIR FLOW SENSOR PLAUSIBILITY SIGNAL RATIO TOO SMALL . . .110
v
P2013-AMBIENT AIR TEMPERATURE SIGNAL VOLTAGE TOO HIGH . . . . . . . . . . .112
P2013-AMBIENT AIR TEMPERATURE SIGNAL VOLTAGE TOO LOW. . . . . . . . . . . .112
P2014-ENGINE OIL SENSOR OIL TEMPERATURE PLAUSIBILITY . . . . . . . . . . . . . .113
P2014-ENGINE OIL SENSOR SIGNAL PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . .113
P2014-ENGINE OIL SENSOR SIGNAL VOLTAGE IS TOO HIGH . . . . . . . . . . . . . . . .113
P2014-ENGINE OIL SENSOR SIGNAL VOLTAGE IS TOO LOW . . . . . . . . . . . . . . . .113
P2040-ENGINE OIL SENSOR CIRCUIT INVALID LEVEL . . . . . . . . . . . . . . . . . . . . . .113
P2040-ENGINE OIL SENSOR CIRCUIT LEVEL OUT OF RANGE . . . . . . . . . . . . . . .113
P2040-ENGINE OIL SENSOR CIRCUIT LEVEL OUT OF RANGE . . . . . . . . . . . . . . .113
P2041-ENGINE OIL SENSOR POOR OIL QUALITY . . . . . . . . . . . . . . . . . . . . . . . . . .113
P2041-ENGINE OIL SENSOR QUALITY MEASUREMENT ERROR . . . . . . . . . . . . . .113
P2041-ENGINE OIL SENSOR QUALITY PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . .113
P2042-ENGINE OIL SENSOR WATER CONTAMINATION. . . . . . . . . . . . . . . . . . . . . .113
P2061-ENGINE OIL SENSOR OPEN CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
P2062-ENGINE OIL SENSOR SIGNAL ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
P2062-ENGINE OIL SENSOR SYNCHRONIZATION ERROR . . . . . . . . . . . . . . . . . . .113
P2015-FUEL RAIL PRESSURE MALFUNCTION MAXIMUM FUEL FLOW
EXCEEDED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
P2016-FUEL RAIL PRESSURE MALFUNCTION DECELERATION ERROR . . . . . . .117
P2016-FUEL RAIL PRESSURE MALFUNCTION FUEL FLOW BELOW MINIMUM
QUANTITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
P2017-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE IS TOO LOW . .117
P2018-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE IS TOO HIGH . .117
P2019-FUEL RAIL PRESSURE MALFUNCTION MAXIMUM FUEL PRESSURE
EXCEEDED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
P2020-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE TOO HIGH . . . .117
P2021-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE TOO LOW . . . . .117
P2023-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE TOO HIGH . . . .117
EXCEEDED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
P2049-FUEL RAIL PRESSURE MALFUNCTION DECELERATION ERROR . . . . . . .117
EXCEEDED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
P2052-FUEL RAIL PRESSURE MALFUNCTION PLAUSIBILITY WITH FUEL
PRESSURE SOLENOID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
P2025-INTAKE PRESSURE SENSOR PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . .125
P2025-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH. . . . . . . . . . . .128
P2030-INTAKE PRESSURE SENSOR CIRCUIT FAULT . . . . . . . . . . . . . . . . . . . . . . .128
P2030-INTAKE PRESSURE SENSOR OPEN CIRCUIT. . . . . . . . . . . . . . . . . . . . . . . .128
P2030-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH. . . . . . . . . . . .128
P2025-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW . . . . . . . . . . . .131
P2030-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW . . . . . . . . . . . .131
P2026-O2 SENSOR CIRCUIT FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
P2026-O2 SENSOR CIRCUIT OPEN CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
P2026-O2 SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH . . . . . . . . . . . . . . . . . .134
P2026-O2 SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW. . . . . . . . . . . . . . . . . . .134
P2028-O2 SENSOR CIRCUIT FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
P2028-O2 SENSOR CIRCUIT OPEN CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
P2028-O2 SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH . . . . . . . . . . . . . . . . . .134
P2028-O2 SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW. . . . . . . . . . . . . . . . . . .134
P2032-O2 SENSOR PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
vi
P2057-O2 SENSOR SIGNAL CIRCUIT SIGNAL VOLTAGE TOO HIGH . . . . . . . . . . .134
P2090-O2 SENSOR SIGNAL FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
P2091-O2 SENSOR LOW O2 CONCENTRATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
P2091-O2 SENSOR SIGNAL PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
P2195-O2 SENSOR HEATER CIRCUIT FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
P2366-O2 CIRCUIT FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
P2034-O2 SENSOR CIRCUIT CALIBRATION VALUE TOO HIGH . . . . . . . . . . . . . . .138
P2034-O2 SENSOR CIRCUIT CALIBRATION VALUE TOO LOW . . . . . . . . . . . . . . . .138
P2043-CAMSHAFT POSITION SENSOR CIRCUIT OPEN CIRCUIT . . . . . . . . . . . . .140
P2043-CAMSHAFT POSITION SENSOR CIRCUIT OPEN OR SHORT CIRCUIT . . .140
P2045-CRANKSHAFT POSITION SENSOR CIRCUIT LOST SIGNAL . . . . . . . . . . . .146
P2045-CRANKSHAFT POSITION SENSOR CIRCUIT SIGNAL PLAUSIBILITY . . . . .146
P2322-CRANKSHAFT POSITION SENSOR PLAUSIBILITY . . . . . . . . . . . . . . . . . . . .146
P2343-CKP PLAUSIBILITY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146
P2062-ENGINE OIL SENSOR MONITORING ERROR . . . . . . . . . . . . . . . . . . . . . . . .149
P2066-MASS AIR FLOW SENSOR PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . .150
P2355-EGR FLOW RATE IS TOO HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150
P2355-EGR FLOW RATE IS TOO LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150
P2066-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO HIGH . . . . . . . .153
P2066-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO LOW. . . . . . . . .153
P2087-INTAKE PRESSURE SENSOR INTAKE RESTRICTION . . . . . . . . . . . . . . . . .156
P2100-FUEL PUMP RELAY CIRCUIT OPEN CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . .157
P2100-FUEL PUMP RELAY CIRCUIT SHORTED TO GROUND . . . . . . . . . . . . . . . . .157
P2100-FUEL PUMP RELAY CIRCUIT SHORTED TO VOLTAGE . . . . . . . . . . . . . . . .159
P2100-FUEL PUMP RELAY EXCESSIVE CURRENT. . . . . . . . . . . . . . . . . . . . . . . . . .159
P2104-STARTER RELAY CIRCUIT SHORT CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . .161
P2152-STARTER RELAY CIRCUIT SHORT TO GROUND . . . . . . . . . . . . . . . . . . . . .161
P2153-STARTER RELAY CIRCUIT OPEN OR SHORTED TO VOLTAGE . . . . . . . . .161
P2110-BOOST PRESSURE SERVO MOTOR CIRCUIT SHORT CIRCUIT. . . . . . . . .164
P2112-BOOST PRESSURE SERVO MOTOR CIRCUIT EXCESSIVE CURRENT . . .164
P2526-BOOST PRESSURE SERVO MOTOR SHORT TO VOLTAGE. . . . . . . . . . . . .164
P2111-BOOST PRESSURE SERVO MOTOR CIRCUIT SHORT TO GROUND . . . . .167
P2112-BOOST PRESSURE SERVO MOTOR CIRCUIT OPEN CIRCUIT . . . . . . . . . .167
P2510-BOOST PRESSURE SERVO MOTOR SHORT TO GROUND . . . . . . . . . . . . .167
P2526-BOOST PRESSURE SERVO MOTOR OPEN CIRCUIT . . . . . . . . . . . . . . . . . .167
P2526-BOOST PRESSURE SERVO MOTOR SHORT TO GROUND . . . . . . . . . . . . .167
P2132-GLOW PLUG CONTROL MODULE CIRCUIT OPEN CIRCUIT . . . . . . . . . . . .171
P2132-GLOW PLUG CONTROL MODULE CIRCUIT SHORTED TO GROUND . . . .171
P2132-GLOW PLUG CONTROL MODULE CIRCUIT SHORTED TO VOLTAGE OR
OPEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171
P2132-GLOW PLUG CONTROL MODULE FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . .171
P2151-FUEL PRESS SOLENOID SIGNAL PLAUSIBILITY HIGH . . . . . . . . . . . . . . . .173
P2151-FUEL PRESS SOLENOID SIGNAL PLAUSIBILITY LOW . . . . . . . . . . . . . . . . .173
vii
P2500-FUEL PRESSURE SOLENOID CIRCUIT OPEN CIRCUIT . . . . . . . . . . . . . . . .173
P2501-FUEL PRESSURE SOLENOID CIRCUIT SHORTED TO GROUND OR B+ . .173
P2197-FUEL QUANTITY SOLENOID OPEN CIRCUIT. . . . . . . . . . . . . . . . . . . . . . . . .177
P2198-FUEL QUANTITY SOLENOID SHORT TO VOLTAGE . . . . . . . . . . . . . . . . . . .177
P2199-FUEL QUANTITY SOLENOID SHORT TO GROUND. . . . . . . . . . . . . . . . . . . .177
P2502-FUEL QUANTITY SOLENOID SHORT TO GROUND. . . . . . . . . . . . . . . . . . . .177
P2203-TORQUE REDUCTION MESSAGE FROM ABS - CAN PLAUSIBILITY . . . . .180
P2203-TORQUE REDUCTION MESSAGE FROM ABS - MESSAGE ERROR . . . . . .180
P2203-TORQUE REDUCTION MESSAGE FROM ABS - MESSAGES MISSING . . .180
P2203-TORQUE REDUCTION MESSAGE FROM ABS - NO COMMUNIOCATION .180
P2203-TORQUE REDUCTION MESSAGE FROM ABS - PLAUSIBILITY #1 . . . . . . .180
P2203-TORQUE REDUCTION MESSAGE FROM ABS PLAUSIBILITY #2. . . . . . . . .180
P2208-ABS BRAKE SIGNAL CAN MESSAGE IMPLAUSIBLE . . . . . . . . . . . . . . . . . .180
P2208-ABS CAN BRAKE SIGNAL PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . .180
P2209-ABS CAN MESSAGE MISSING OR INCORRECT . . . . . . . . . . . . . . . . . . . . . .180
P2253-STEERING ANGLE SENSOR PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . .180
P2204-TORQUE REDUCTION MESSAGE FROM TCM - CAN PLAUSIBILITY . . . . .182
P2204-TORQUE REDUCTION MESSAGE FROM TCM - ENGINE STOP . . . . . . . . .182
P2204-TORQUE REDUCTION MESSAGE FROM TCM - MESSAGE ERROR . . . . .182
P2204-TORQUE REDUCTION MESSAGE FROM TCM - MESSAGES MISSING . . .182
P2204-TORQUE REDUCTION MESSAGE FROM TCM - PLAUSIBILITY. . . . . . . . . .182
P2204-TORQUE REDUCTION MESSAGE FROM TCM - TCM DTC #1. . . . . . . . . . .182
P2204-TORQUE REDUCTION MESSAGE FROM TCM - TCM DTC #2. . . . . . . . . . .182
P2210-ESM CAN MESSAGE MISSING OR INCORRECT. . . . . . . . . . . . . . . . . . . . . .184
P2234-ABS DTC EXTERNAL QUANTITY CONTROL FAULT PRESENT . . . . . . . . . .184
P2252-LATERAL ACCELERATOR SENSOR PLAUSIBILTY. . . . . . . . . . . . . . . . . . . . .184
P2211-ETC CAN MESSAGE MISSING OR INCORRECT . . . . . . . . . . . . . . . . . . . . . .186
P2258-TCM MESSAGE ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .186
P2258-TCM NO CAN MESSAGE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .186
P2217-TCM DTC INTERNAL FAULT PRESENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .188
P2218-TCM DTC 1-2 AND 4-5 SHIFT SOLENOID FAULT PRESENT . . . . . . . . . . . .188
P2219-TCM DTC 2-3 SHIFT SOLENOID FAULT PRESENT . . . . . . . . . . . . . . . . . . . .188
P2220-TCM DTC 3-4 SHIFT SOLENOID FAULT PRESENT . . . . . . . . . . . . . . . . . . . .188
P2221-TCM DTC TORQUE CONVERTER CLUTCH SOLENOID FAULT PRESENT.188
P2222-TCM DTC MODULATING PRESSURE SOLENOID FAULT PRESENT . . . . . .188
P2223-TCM DTC SHIFT PRESSURE SOLENOID FAULT PRESENT. . . . . . . . . . . . .188
P2224-TCM DTC VALVE VOLTAGE SUPPLY FAULT PRESENT . . . . . . . . . . . . . . . .188
P2225-TCM DTC SPEED SENSOR VOLTAGE FAULT PRESENT . . . . . . . . . . . . . . .188
P2226-TCM DTC EWM CAN MESSAGE FAULT PRESENT . . . . . . . . . . . . . . . . . . . .188
P2227-TCM DTC RIGHT REAR WHEEL SPEED IMPLAUSIBLE FAULT PRESENT .188
P2228-TCM DTC TRANSMISSION RATIO ERROR FAULT PRESENT . . . . . . . . . . .188
P2229-TCM DTC CAN MSG IMPLAUSIBLE FAULT PRESENT . . . . . . . . . . . . . . . . .188
P2230-TCM DTC TCC EXCESSIVE POWER CONSUMPTION FAULT PRESENT . .188
P2231-TCM DTC NOT UNEQUIVOCAL FAULT PRESENT . . . . . . . . . . . . . . . . . . . . .188
P2232-TCM DTC NEGATIVE GEAR COMPARISON FAULT PRESENT . . . . . . . . . . .188
P2240-ABS STEERING ANGLE SENSOR CAN MESSAGE IMPLAUSIBLE 1 . . . . . .190
P2240-ABS STEERING ANGLE SENSOR CAN MESSAGE IMPLAUSIBLE 2 . . . . . .190
P2242-ABS BRAKE MESSAGE PLAUSIBILITY 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . .192
P2242-ABS BRAKE MESSAGE PLAUSIBILITY 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . .192
P2244-INSTRUMENT CLUSTER MESSAGE PLAUSIBILITY . . . . . . . . . . . . . . . . . . .194
P2259-TORQUE REDUCTION MESSAGE FROM HVAC- PARITY ERROR. . . . . . . .196
P2259-TORQUE REDUCTION MESSAGE FROM HVAC- SWITCH SIGNAL
ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .196
viii
P2259-TORQUE REDUCTION MESSAGE FROM HVAC- SWITCH SIGNAL
PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .196
P229-INSTRUMENT CLUSTER MESSAGE - AMBIENT TEMPERATURE SIGNAL
PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .197
P2306-SENSOR SUPPLY 2 VOLTAGE IS TOO HIGH . . . . . . . . . . . . . . . . . . . . . . . . .198
P2306-SENSOR SUPPLY 2 VOLTAGE IS TOO LOW . . . . . . . . . . . . . . . . . . . . . . . . .200
P2332-SENSOR SUPPLY 3 VOLTAGE IS TOO LOW . . . . . . . . . . . . . . . . . . . . . . . . .203
P2332-SENSOR SUPPLY 3 VOLTAGE IS TOO HIGH . . . . . . . . . . . . . . . . . . . . . . . . .206
P2333-S/C VEHICLE SPEED PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .209
P2338-S/C EXCESSIVE ACCELERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .209
P2338-S/C EXCESSIVE DECELERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .209
P2339-ECM CHECKSUM ERROR #1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .211
P2339-ECM CHECKSUM ERROR #2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .211
P2339-ECM INVALID CODING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .211
P2339-ECM INVALID DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .211
P2344-KICKDOWN SWITCH PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .212
P2347-AUTOMATIC TRANSMISSION CODED AS MANUAL TRANSMISSION . . . . .213
P2347-CAN BUS CIRCUIT INTERUPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .213
P2347-MANUAL TRANSMISSIO CODED AS AUTO TRANSMISSION . . . . . . . . . . . .213
P2347-WRITE ERROR TO EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .213
P2351-ECM SUPPLY VOLTAGE TOO LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .214
P2359-BOOST PRESSURE TOO HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .216
P2359-BOOST PRESSURE TOO LOW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .216
P2511-EGR VALVE SIGNAL CIRCUIT SHORTED TO GROUND . . . . . . . . . . . . . . . .218
P2527-EGR VALVE SIGNAL CIRCUIT OPEN CIRCUIT. . . . . . . . . . . . . . . . . . . . . . . .218
P2527-EGR VALVE SIGNAL CIRCUIT SHORTED TO GROUND . . . . . . . . . . . . . . . .218
P2514-CRANKCASE VENT HEATER OPEN CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . .221
P2514-CRANKCASE VENT HEATER SHORTED TO GROUND . . . . . . . . . . . . . . . . .221
P2514-CRANKCASE VENT HEATER SHORTED TO VOLTAGE. . . . . . . . . . . . . . . . .221
P2521-IMPROPER START ATTEMPT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .224
P2527-EGR VALVE SIGNAL CIRCUIT SHORTED TO VOLTAGE . . . . . . . . . . . . . . . .225
P2531-FUEL INJECTOR 1 READ TOO LARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227
P2531-FUEL INJECTOR 1 READ TOO SMALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227
P2606-CMP/CKP SYNCHRONIZATION ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . .229
*CHECKING THE FUEL PRESSURE SENSOR CIRCUITS . . . . . . . . . . . . . . . . . . . . .232
ix
*CHECKING THE FUEL PRESSURE SOLENOID CIRCUITS . . . . . . . . . . . . . . . . . . .233
*CHECKING THE FUEL QUANTITY SOLENOID CIRCUITS . . . . . . . . . . . . . . . . . . . .234
*CHECKING THE POWER AND GROUNDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .235
*ENGINE CRANKS BUT WILL NOT START . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .239
*ENGINE WILL NOT CRANK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .242
VERIFICATION TESTS
VERIFICATION TESTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .246
8.0 COMPONENT LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .249
8.1 CONTROL MODULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .249

8.2 CONTROLS AND SOLENOIDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .249
8.3 DATA LINK CONNECTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .250
8.4 SENSORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .251
8.5 SWITCHES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .253
9.0 CONNECTOR PINOUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .255
ACCELERATOR PEDAL POSITION SENSOR (OBD) . . . . . . . . . . . . . . . . . . . . . . . . .255

AIRBAG CONTROL MODULE - YELLOW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .255
BOOST PRESSURE SENSOR (OBD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .255
BOOST PRESSURE SERVOMOTOR (OBD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .256
CAMSHAFT POSITION SENSOR - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .256
CONTROLLER ANTILOCK BRAKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .257
CRANKCASE HEATER - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .257
CRANKSHAFT POSITION SENSOR - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .258
DATA LINK CONNECTOR - BLACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .258
EGR VALVE - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .258
ENGINE CONTROL MODULE C1 (OBD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .259
ENGINE CONTROL MODULE C2 (OBD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .260
ENGINE COOLANT TEMPERATURE SENSOR - BLACK . . . . . . . . . . . . . . . . . . . . . .260
ENGINE OIL SENSOR - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .261
FUEL INJECTOR NO. 1 - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .261
FUEL PRESSURE SENSOR - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .262
FUEL PRESSURE SOLENOID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .262
FUEL PUMP (OBD). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .262
FUEL PUMP RELAY (OBD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .263
FUEL QUANTITY CONTROL VALVE (OBD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .263
FUEL TEMPERATURE SENSOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .263
ENGINE CONTROL RELAY (FUSE BLOCK NO. 1) . . . . . . . . . . . . . . . . . . . . . . . . . . .265
FUSES (FUSE BLOCK NO. 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .265
FUSES (FUSE BLOCK NO. 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .267
FUSES (FUSE/RELAY BLOCK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .269
STARTER MOTOR RELAY (FUSE/RELAY BLOCK) . . . . . . . . . . . . . . . . . . . . . . . . . . .269
GLOW PLUG CONTROL MODULE C1 - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . .270
GLOW PLUG CONTROL MODULE C2 - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . .270
INTAKE AIR PRESSURE SENSOR (OBD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .270
INTAKE AIR TEMPERATURE SENSOR - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . .270
x
KICK DOWN SWITCH - BLACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .271
MASS AIR FLOW SENSOR - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .271
OXYGEN SENSOR (OBD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .271
FUSED IGNITION SWITCH RUN-START RELAY (RELAY BLOCK) . . . . . . . . . . . . . .273
SPEED CONTROL SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .273
WATER IN FUEL SENSOR - BLACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .273
10.0 SCHEMATIC DIAGRAMS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .275
10.1 ENGINE CONTROL MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .275

10.2 ENGINE CONTROL MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .276
11.0 CHARTS AND GRAPHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .277
xi
NOTES
xii
GENERAL INFORMATION
1.0 INTRODUCTION 2.0 IDENTIFICATION OF
SYSTEM
The procedures contained in this manual include
all specifications, instructions and graphics needed The ECM is located to the left of the steering
to diagnose engine control module (ECM) and sen- column behind the steering column opening cover.
try key remote entry module (SKREEM) problems; The sentry remote entry module (SKREEM) is
they are no start, diagnostic trouble code (DTC) and attached to the rear of the instrument cluster.
no trouble code problems for the ECM. The diagnos-
tics in this manual are based on the trouble condi-
tion or symptom being present at the time of diag- 3.0 SYSTEM DESCRIPTION AND
nosis. FUNCTIONAL OPERATION
When repairs are required, refer to the appropri-
ate service information for the proper removal and
repair procedure. 3.1 GENERAL DESCRIPTION
Diagnostic procedures change every year. New
diagnostic systems may be added; carryover sys- The 2.7L direct injection diesel engine system is
tems may be enhanced. IT IS RECOMMENDED equipped with the latest technical advances. The
THAT YOU REVIEW THE ENTIRE MANUAL TO on-board diagnostics incorporated in the engine
BECOME FAMILIAR WITH ALL NEW AND control module and SKREEM are intended to assist
CHANGED DIAGNOSTIC PROCEDURES. the field technician in repairing vehicle problems by
This manual will cover all the necessary require- the quickest means.
ments to begin a logical diagnostic path for each The engine system incorporates a common rail
problem. If there is a diagnostic trouble code (DTC) fuel delivery design with exhaust emission feed-
detected, go to the trouble code test. If there are no back. This design utilizes electronically controlled
DTCs present, go to a no trouble code (*), symptom solenoid valve type fuel injectors. Each injector is
based test. controlled individually by the ECM. Injector timing
This book reflects many suggested changes from and fuel quantity are controlled by the ECM based
readers of past issues. After using this book, if you on inputs from various sensors. The precision con-
have any comments or recommendations, please fill trol of the injectors by the ECM helps to reduce the
out the form at the back of the book and mail it back engine noise, odor and smoke.
to us.
3.2 FUNCTIONAL OPERATION
1.1 SYSTEM COVERAGE
This diagnostic procedures manual covers 2005 3.2.1 ECM ON-BOARD DIAGNOSTICS
Sprinter vehicles equipped with the 2.7L common The ECM is programmed to monitor different
rail diesel engine. circuits of the diesel fuel injection system. This
monitoring is called on-board diagnostics.
1.2 SIX-STEP TROUBLESHOOTING Certain criteria must be met for a diagnostic
PROCEDURE trouble code to be entered into the ECM memory.
The criteria may be a range of: engine rpm, engine
Diagnosis of the engine control module (ECM) temperature, time or other input signals to the
and sentry key immobilizer system (SKREEM) is ECM. If all of the criteria for monitoring a system or
done in six basic steps: circuit are met, and a problem is sensed, then a
• verification of complaint DTC will be stored in the ECM memory.
• verification of any related symptom It is possible that a DTC for a monitored circuit
may not be entered into the ECM memory, even
• symptom analysis
though a malfunction has occurred. This may hap-
• problem isolation pen when the monitoring criteria have not been
• repair of isolated problem met.
• verification of proper operation The ECM compares input signal voltages from
each input device with specifications (the estab-
NOTE: All tests in this manual should be per- lished high and low limits of the input range) that
formed with the engine at operating temperature, are programmed into it for that device. If the input
unless otherwise specified within a particular test. voltage is not within the specifications and other
trouble code criteria are met, a DTC will be stored
in the ECM memory.
1
GENERAL INFORMATION
3.2.2 ECM OPERATING MODES position. Other less critical faults will result in
power reduction throughout the full range of driv-
As input signals to the ECM change, the ECM
ing conditions.
adjusts its response to the output devices. For
example, the ECM must calculate a different fuel
Overspeed Detection Mode
quantity and fuel timing for engine idle condition
If the ECM detects engine RPM that exceeds
than it would for a wide open throttle condition.
5200 RPM, the ECM will set a DTC in memory,
There are several different modes of operation that
limit engine RPM to no more than 2500 RPM, and
determine how the ECM responds to the various
illuminate the MIL until the DTC is cleared.
input signals.
Ignition Switch On (Engine Off) After-Run Mode

The ECM transfers RAM information to ROM
When the ignition is turned on the ECM activates
and performs an Input/Output state check.
the glow plug relay for a time period that is deter-
mined by engine coolant temperature, intake air
temperature and battery voltage.
3.2.3 MONITORED CIRCUITS
The ECM is able to monitor and identify most
Engine Start-Up Mode driveability related trouble conditions. Some cir-
The ECM uses the intake air temperature sensor, cuits are directly monitored through ECM feedback
engine temperature sensor and the crankshaft po- circuitry. In addition, the ECM monitors the voltage
sition sensor (engine speed) inputs to determine state of some circuits and compares those states
fuel injection quantity. with expected values. Other systems are monitored
indirectly when the ECM conducts a rationality test
Normal Driving Modes to identify problems.
Engine idle, warm-up, acceleration, deceleration Although most subsystems of the engine control
and wide open throttle modes are controlled based module are either directly or indirectly monitored,
on all of the sensor inputs to the ECM. The ECM there may be occasions when diagnostic trouble
uses these sensor inputs to adjust fuel quantity and codes are not immediately identified. For a trouble
fuel injector timing. EGR valve control is performed code to set, a specific set of conditions must occur
using feedback from the oxygen sensor. An oxygen and unless these conditions occur, a DTC will not
sensor is located in the exhaust manifold to sample set.
oxygen content exiting the engine cylinders. The
ECM uses the O2 sensor, along with other sensor 3.2.4 SKREEM OVERVIEW
inputs, to govern the amount of exhaust gas recir- The sentry key remote entry module system
culation to reduce HC (HydroCarbons) and CO (SKREEM) is designed to prevent unauthorized
(Carbon Monoxide). Engine coolant is routed vehicle operation. The system consists of a sentry
through the base of the EGR valve to provide key remote entry module (SKREEM), ignition
additional cooling of the exhaust gas, which further key(s) equipped with a transponder chip and the
helps the reductions of emissions. The EGR valve ECM. When the ignition switch is turned on, the
has a self-cleaning function. When the engine is SKREEM interrogates the ignition key. If the igni-
shut off, the EGR valve rotates twice to reduce tion key is Valid or Invalid, the SKREEM sends a
carbon deposits at the valve seat. message to the ECM indicating ignition key status.
Upon receiving this message the ECM will termi-
Overheat Production Mode nate engine operation or allow the engine to con-
If the engine temperature is above 105°C (221°F) tinue to operate.
and vehicle speed is above 40 km/h (25 MPH) the
ECM will limit fuel quantity for engine protection. 3.2.5 SKREEM ON-BOARD DIAGNOSTICS
The SKREEM has been programmed to transmit
Limp-In Mode
and monitor many different coded messages as well
The ECM utilizes different degrees of engine
as CAN Bus messages. This monitoring is called
limp-in. The ECM is able to limit engine rpm,
On-Board Diagnostics. Certain criteria must be met
engine power output (turbo boost reduction), acti-
for a DTC to be entered into SKREEM memory. The
vate engine cooling fan or all of these functions
criteria may be a range of; input voltage, CAN Bus
based on the type of fault that is detected. Critical
message or coded messages to the SKREEM. If all
engine performance faults such as accelerator pedal
the criteria for monitoring a circuit or function are
position sensor fault will result in a fixed idle speed
met and a fault is detected, a DTC will be stored in
of approximately 680 rpm regardless of actual pedal
the SKREEM memory and the START ERROR indi-
cator will be turned on in the instrument cluster.
2
GENERAL INFORMATION
3.2.6 SKREEM OPERATION beginning of each test. When the fault is not a hard
code, an intermittent test must be performed.
When ignition power is supplied to the SKREEM,
the SKREEM performs an internal self-test. After NOTE: If the DRBIIIT displays faults for
the self-test is complete, the SKREEM energizes multiple components (i.e. ECT, MAF, IAT
the antenna (this activates the transponder chip)
sensors) identify and check the shared
and sends a challenge to the transponder chip. The
transponder chip responds to the challenge by gen-
circuits for possible problems before
erating an encrypted response message. continuing (i.e. sensor grounds or 5-volt
After responding to the coded message, the tran- supply circuits). Refer to the appropriate
sponder sends a transponder ID message to the schematic to identify shared circuits.
SKREEM. The SKREEM compares the transpon-
der ID message to the available valid key codes in
SKREEM memory (8 key maximum at any one 3.3.2 INTERMITTENT CODE
time). After validating the ignition key the A DTC that is not current every time the ECM/
SKREEM sends a CAN Bus message request to the SKREEM checks the circuit or function is an inter-
ECM, then waits for the ECM response. If the ECM mittent code. Most intermittent DTCs are caused
does not respond, the SKREEM will send the re- by wiring or connector problems. Problems that
quest again. If the ECM does not respond again, the come and go like this are the most difficult to
SKREEM will stop sending the request and store a diagnose; they must be looked for under specific
trouble code in memory. If the ECM sends a correct conditions that cause them. The following checks
response to the SKREEM, the SKREEM sends a may assist you in identifying a possible intermit-
valid/invalid key message to the ECM. The ECM tent problem.
will allow or disallow engine operation based on this – Visually inspect the related wire harness con-
message. nectors. Look for broken, bent, pushed out or
Secret Key - an electronically stored value (iden- corroded terminals.
tification number) that is unique to each SKREEM.
The secret key is stored in the SKREEM, ECM and – Visually inspect the related wire harness.
all ignition key transponders. Look for chafed, pierced or partially broken
Challenge - a random number that is generated by wire.
the SKREEM at each ignition key cycle. – Refer to hotlines or technical service bulletins
The secret key and challenge are the two vari- that may apply.
ables used in the algorithm that produces the
encrypted response message. The transponder uses NOTE: Electromagnetic (radio) interference
the crypto algorithm to receive, decode and respond can cause an intermittent system
to the message sent by the SKREEM. After re- malfunction. This interference can interrupt
sponding to the coded message, the transponder communication between the ignition key
sends a transponder ID message to the SKREEM. transponder and the SKREEM.
3.3 DIAGNOSTIC TROUBLE CODES 3.3.3 ECM DIAGNOSTIC TROUBLE CODES

Each diagnostic trouble code (DTC) is diagnosed IMPORTANT NOTE: Before replacing the
by following a specific procedure. The diagnostic ECM for a failed driver, control circuit or
test procedure contains step-by-step instruction for
ground circuit, be sure to check the related
determining the cause of the DTC as well as no
trouble code problems. It is not necessary to per-
component/circuit integrity for failures not
form all of the tests in this book to diagnose an detected due to a double fault in the circuit.
individual code. Most ECM driver/control circuit failures are
Always begin diagnosis by reading the DTCs caused by internal failures to components
using the DRBIIIt. This will direct you to the (i.e. relays and solenoids) and shorted
specific test(s) that must be performed. circuits (i.e. sensor pull-ups, drivers and
ground circuits). These faults are difficult to
3.3.1 HARD CODE detect when a double fault has occurred and
A DTC that comes back within one cycle of the only one DTC has set.
ignition key is a hard code. This means that the If the DRBIIIt displays faults for multiple com-
problem is current every time the ECM/SKREEM ponents (i.e. MAF, ECT, ENG OIL, etc.), identify
checks that circuit or function. Procedures in this and check the shared circuits for possible problems
manual verify if the DTC is a hard code at the before continuing (i.e. sensor grounds or 5-volt
3
GENERAL INFORMATION
supply circuits). Refer to the appropriate wiring crankshaft position sensor circuit lost signal
diagrams to identify shared circuits. crankshaft position sensor circuit signal plausibil-
abs brake message plausibility 1 ity
abs brake message plausibility 2 crankshaft position sensor plausibility
abs brake signal can message implausible cylinder #1 injector open circuit
abs can brake signal plausibility cylinder #2 injector open circuit
abs can message missing or incorrect cylinder #3 injector open circuit
abs dtc external quantity control fault present cylinder #4 injector open circuit
abs steering angle sensor can message implausible cylinder #5 injector open circuit
1 cylinder 1-injector circuit excessive current
abs steering angle sensor can message implausible cylinder 1-injector circuit open or shorted to ground
2 cylinder 1-injector circuit shorted to voltage
acc pedal position sensor 1 ckt plausibility cylinder 1-injector circuit shorted to ground
acc pedal position sensor 1 ckt signal voltage too cylinder 2-injector circuit excessive current
high cylinder 2-injector circuit open or shorted to ground
acc pedal position sensor 1 ckt signal voltage too low cylinder 2-injector circuit shorted to ground
acc pedal position sensor 2 circuit plausibility cylinder 2-injector circuit shorted to voltage
acc pedal position sensor 2 ckt signal voltage too cylinder 3-injector circuit excessive current
high cylinder 3-injector circuit open or shorted to ground
acc pedal position sensor 2 ckt signal voltage too low cylinder 3-injector circuit shorted to ground
acm circuit fault cylinder 3-injector circuit shorted to voltage
acm circuit short to voltage cylinder 4-injector circuit excessive current
ambient air temperature signal voltage too high cylinder 4-injector circuit open or shorted to ground
ambient air temperature signal voltage too low cylinder 4-injector circuit shorted to ground
app sensor plausibility cylinder 4-injector circuit shorted to voltage
atmospheric pressure sensor plausibility with boost cylinder 5-injector circuit excessive current
pressure sensor cylinder 5-injector circuit open or shorted to ground
atmospheric pressure sensor signal voltage too high cylinder 5-injector circuit shorted to ground
atmospheric pressure sensor signal voltage too low cylinder 5-injector circuit shorted to voltage
automatic transmission coded as manual transmis- ecm a/d converter high
sion ecm a/d converter low
boost pressure servo motor circuit excessive current ecm a/d converter plausibility
boost pressure servo motor circuit open circuit ecm checksum error #1
boost pressure servo motor circuit short circuit ecm checksum error #2
boost pressure servo motor circuit short to ground ecm incorrect value
boost pressure servo motor excessive current ecm injection quantity error
boost pressure servo motor open circuit ecm injector monitoring 1
boost pressure servo motor short to ground ecm injector monitoring 2
boost pressure servo motor short to ground ecm injector monitoring 3
boost pressure servo motor short to voltage ecm injector monitoring 4
boost pressure too high ecm injector output stage #1
boost pressure too low ecm injector output stage #1 short circuit
camshaft position sensor circuit open circuit ecm injector output stage #2
camshaft position sensor circuit open or short cir- ecm injector output stage #2 short circuit
cuit ecm injector undervoltage
can bus circuit interuption ecm internal error
can data bus -bus circuit fault ecm internal error
can message error ecm internal error
*checking the fuel pressure sensor circuits ecm internal error
*checking the fuel pressure solenoid circuits ecm internal error 1
*checking the fuel quantity solenoid circuits ecm internal error 1
*checking the power and grounds ecm internal error 1
ckp plausibility ecm internal error 1
cmp/ckp synchronization error ecm internal error 1
crankcase vent heater excessive current ecm internal error 2
crankcase vent heater open circuit ecm internal error 2
crankcase vent heater shorted to ground ecm internal error 2
crankcase vent heater shorted to voltage ecm internal error 3
4
GENERAL INFORMATION
ecm internal error 3 fuel injector 2 read too large
ecm internal error 4 fuel injector 2 read too large
ecm internal error 4 fuel injector 2 read too small
ecm internal error 5 fuel injector 2 read too small
ecm internal fault fuel injector 3 read too large
ecm invalid coding fuel injector 3 read too large
ecm invalid data fuel injector 3 read too small
ecm read error fuel injector 3 read too small
ecm read/write error fuel injector 4 read too large
ecm supply voltage too low fuel injector 4 read too large
ecm voltage supply is too high fuel injector 4 read too small
ecm voltage supply is too low fuel injector 4 read too small
ecm write error fuel injector 5 read too large
egr flow rate is too high fuel injector 5 read too large
egr flow rate is too low fuel injector 5 read too small
egr valve excessive current fuel injector 5 read too small
egr valve signal circuit open circuit fuel press sensor circuit malf signal voltage too high
egr valve signal circuit shorted to ground fuel press sensor circuit malf signal voltage too low
egr valve signal circuit shorted to ground fuel press solenoid signal plausibility high
egr valve signal circuit shorted to voltage fuel press solenoid signal plausibility low
engine control relay plausibility fuel pressure sensor circuit signal voltage too high
engine control relay shuts off too early fuel pressure sensor circuit signal voltage too low
engine control relay shuts off too late fuel pressure solenoid circuit excessive current
engine coolant temp sensor circuit plausibility fuel pressure solenoid circuit open circuit
engine coolant temp sensor circuit plausibility fuel pressure solenoid circuit shorted to ground or
engine coolant temp sensor circuit plausibility with b+
engine oil sensor fuel pump relay circuit open circuit
engine coolant temp sensor circuit signal voltage too fuel pump relay circuit shorted to ground
high fuel pump relay circuit shorted to voltage
engine coolant temp sensor circuit signal voltage too fuel pump relay excessive current
high fuel quantity solenoid ecm thermal overload
engine coolant temp sensor circuit signal voltage too fuel quantity solenoid open circuit
low fuel quantity solenoid short to ground
engine coolant temp sensor circuit signal voltage too fuel quantity solenoid short to ground
low fuel quantity solenoid short to voltage
*engine cranks but will not start fuel rail pressure malfunction deceleration error
engine oil sensor circuit invalid level fuel rail pressure malfunction deceleration error
engine oil sensor circuit level out of range fuel rail pressure malfunction fuel flow below min-
engine oil sensor circuit level out of range imum quantity
engine oil sensor monitoring error fuel rail pressure malfunction maximum fuel flow
engine oil sensor oil temperature plausibility exceeded
engine oil sensor open circuit fuel rail pressure malfunction maximum fuel pres-
engine oil sensor poor oil quality sure exceeded
engine oil sensor quality measurement error fuel rail pressure malfunction maximum fuel pres-
engine oil sensor quality plausibility sure exceeded
engine oil sensor signal error fuel rail pressure malfunction maximum fuel pres-
engine oil sensor signal plausibility sure exceeded
engine oil sensor signal voltage is too high fuel rail pressure malfunction plausibility with fuel
engine oil sensor signal voltage is too low pressure solenoid
engine oil sensor synchronization error fuel rail pressure malfunction rail pressure is too
engine oil sensor water contamination high
*engine will not crank fuel rail pressure malfunction rail pressure is too
esm can message missing or incorrect low
etc can message missing or incorrect fuel rail pressure malfunction rail pressure is too
fuel injector 1 read too large low
fuel injector 1 read too large fuel rail pressure malfunction rail pressure is too
fuel injector 1 read too small low
fuel injector 1 read too small fuel rail pressure malfunction rail pressure too high
5
GENERAL INFORMATION
fuel rail pressure malfunction rail pressure too high injector 2 injection time below limit
fuel rail pressure malfunction rail pressure too low injector 3 injection time above limit
fuel temperature sensor circuit signal voltage too injector 3 injection time below limit
high injector 4 injection time above limit
fuel temperature sensor circuit signal voltage too injector 4 injection time below limit
low injector 5 injection time above limit
fuel temperature sensor plausibility injector 5 injection time below limit
general leakage injector bank error
glow plug #1 circuit excessive current injector bank error
glow plug #1 circuit open circuit injector circuit fault
glow plug #1 circuit short to ground injector circuit fault
glow plug #1 circuit short to voltage injector circuit low side shorted to ground
glow plug #2 circuit excessive current injector circuit low side shorted to ground
glow plug #2 circuit open circuit injector circuit shorted to ground or voltage
glow plug #2 circuit short to ground injector circuit shorted to ground or voltage
glow plug #2 circuit short to voltage instrument cluster message -ambient temperature
glow plug #3 circuit excessive current signal plausibility
glow plug #3 circuit open circuit instrument cluster message plausibility
glow plug #3 circuit short to ground intake air temp sensor circuit signal voltage too high
glow plug #3 circuit short to voltage intake air temp sensor circuit signal voltage too low
glow plug #4 circuit excessive current intake air temp sensor signal voltage too high
glow plug #4 circuit open circuit intake air temp sensor signal voltage too low
glow plug #4 circuit short to ground intake pressure sensor can message error
glow plug #4 circuit short to voltage intake pressure sensor circuit fault
glow plug #5 circuit excessive current intake pressure sensor intake restriction
glow plug #5 circuit open circuit intake pressure sensor open circuit
glow plug #5 circuit short to ground intake pressure sensor plausibility
glow plug #5 circuit short to voltage intake pressure sensor plausibility
glow plug control circuit preglow fault intake pressure sensor signal voltage too high
glow plug control circuit preglow short to ground intake pressure sensor signal voltage too high
glow plug control circuit preglow short to voltage intake pressure sensor signal voltage too high
glow plug control module circuit open circuit intake pressure sensor signal voltage too low
glow plug control module circuit shorted to ground intake pressure sensor signal voltage too low
glow plug control module circuit shorted to voltage intake pressure sensor signal voltage too low
or open internal error counter fault
glow plug control module fault internal error engine shut off
glow plug indicator error internal error engine voltage monitoring
glow plug module communication error internal error engine voltage monitoring
glow plug module -communication error internal voltage error
glow plug module -excess current kickdown switch plausibility
glow plug module excessive current error lateral accelerator sensor plausibilty
glow plug module -incorrect timer leakage cylinder #1
glow plug module -internal fault leakage cylinder #2
glow plug module timer error leakage cylinder #3
ignition voltage -voltage error leakage cylinder #4
immobilizer leakage cylinder #5
immobilizer maf sensor signal plausibility
immobilizer manual transmissio coded as auto transmission
immobilizer mass air flow sensor negative deviation
immobilizer can message error mass air flow sensor plausibility
improper start attempt mass air flow sensor plausibility air mass too high
injection fault excessive engine speed mass air flow sensor plausibility air mass too high
injection fault -excessive temperature mass air flow sensor plausibility air mass too low
injection fault -quantity error mass air flow sensor plausibility air mass too low
injection fault -torque limit mass air flow sensor plausibility signal ratio error
injector 1 injection time above limit mass air flow sensor plausibility signal ratio too
injector 1 injection time below limit large
injector 2 injection time above limit mass air flow sensor plausibility signal ratio too
6
GENERAL INFORMATION
small sensor supply 3 voltage is too low
mass air flow sensor positive deviation starter relay circuit ecm thermal overload
mass air flow sensor signal circuit open or shorted starter relay circuit open or shorted to voltage
mass air flow sensor signal voltage too high starter relay circuit short circuit
mass air flow sensor signal voltage too high starter relay circuit short to ground
mass air flow sensor signal voltage too low steering angle sensor plausibility
mass air flow sensor signal voltage too low tcm dtc 1-2 and 4-5 shift solenoid fault present
mass air flow sensor signal voltage too low tcm dtc 2-3 shift solenoid fault present
mass air flow sensor signal voltage too low tcm dtc 3-4 shift solenoid fault present
mass air flow sensor supply voltage too high tcm dtc can msg implausible fault present
mass air flow sensor supply voltage too low tcm dtc ewm can message fault present
misfire cylinder #1 tcm dtc internal fault present
misfire cylinder #1 tcm dtc modulating pressure solenoid fault present
misfire cylinder #2 tcm dtc negative gear comparison fault present
misfire cylinder #2 tcm dtc not unequivocal fault present
misfire cylinder #3 tcm dtc right rear wheel speed implausible fault
misfire cylinder #3 present
misfire cylinder #4 tcm dtc shift pressure solenoid fault present
misfire cylinder #4 tcm dtc speed sensor voltage fault present
misfire cylinder #5 tcm dtc tcc excessive power consumption fault
misfire cylinder #5 present
misfire detected tcm dtc torque converter clutch solenoid fault
no message received from skreem present
o2 circuit fault tcm dtc transmission ratio error fault present
o2 sensor circuit calibration value too high tcm dtc valve voltage supply fault present
o2 sensor circuit calibration value too high tcm message error
o2 sensor circuit calibration value too high tcm no can message
o2 sensor circuit calibration value too low torque reduction message from abs -can plausibility
o2 sensor circuit calibration value too low torque reduction message from abs -message error
o2 sensor circuit calibration value too low torque reduction message from abs -messages miss-
o2 sensor circuit fault ing
o2 sensor circuit fault torque reduction message from abs -no communica-
o2 sensor circuit open circuit tion
o2 sensor circuit open circuit torque reduction message from abs -plausibility #1
o2 sensor circuit signal voltage too high torque reduction message from abs plausibility #2
o2 sensor circuit signal voltage too high torque reduction message from hvac switch signal
o2 sensor circuit signal voltage too low plausibility
o2 sensor circuit signal voltage too low torque reduction message from hvac-parity error
o2 sensor heater circuit fault torque reduction message from hvac-switch signal
o2 sensor low o2 concentration error
o2 sensor plausibility torque reduction message from tcm -can plausibil-
o2 sensor plausibility ity
o2 sensor plausibility torque reduction message from tcm -engine stop
o2 sensor plausibility torque reduction message from tcm -message error
o2 sensor plausibility torque reduction message from tcm -messages miss-
o2 sensor signal circuit signal voltage too high ing
o2 sensor signal circuit signal voltage too high torque reduction message from tcm -plausibility
o2 sensor signal circuit signal voltage too high torque reduction message from tcm -tcm dtc #1
o2 sensor signal fault torque reduction message from tcm -tcm dtc #2
o2 sensor signal plausibility water in fuel sensor signal error
s/c excessive acceleration water in fuel sensor -water in fuel
s/c excessive deceleration wheel speed sensor plaus -can bus message from
s/c vehicle speed plausibility abs
sensor supply 1 voltage is too high write error to eeprom
sensor supply 1 voltage is too low
sensor supply 2 voltage is too high
sensor supply 2 voltage is too low
sensor supply 3 voltage is too high
7
GENERAL INFORMATION
3.3.4 HANDLING NO TROUBLE CODE 4.0 DISCLAIMERS, SAFETY,
PROBLEMS WARNINGS
After reading Section 3.0 (System Description
and Functional Operation), you should have a bet- 4.1 DISCLAIMERS
ter understanding of the theory and operation of the
on-board diagnostics and how this relates to the All information, illustrations and specifications
diagnosis of a vehicle that may have a driveability- contained in this manual are based on the latest
related symptom or complaint. When there are no information available at the time of publication.
trouble codes present, refer to the no trouble code The right is reserved to make changes at any time
(*) tests. without notice.
3.4 USING THE DRBIIIT 4.2 SAFETY

Refer to the DRBIIIt user’s guide for instructions
and assistance with reading the DTCs, erasing the 4.2.1 TECHNICIAN SAFETY INFORMATION
DTCs, lab scope usage and other DRBIIIt func-
tions. WARNING: HIGH-PRESSURE FUEL LINES
DELIVER DIESEL FUEL UNDER EXTREME
3.4.1 DRBIIIT DOES NOT POWER UP
PRESSURE FROM THE INJECTION PUMP TO
If the LEDs do not light or no sound is emitted at THE FUEL INJECTORS. THIS MAY BE AS
start up, check for loose cable connections or a bad HIGH AS 23,200 PSI (1600 BAR). USE
cable. Check the vehicle battery voltage at data link
EXTREME CAUTION WHEN INSPECTING
connector cavity 16. A minimum of 11.0 volts is
required to adequately power the DRBIIIt. Check
FOR HIGH-PRESSURE FUEL LEAKS. FUEL
for proper ground connection at data link connector UNDER THIS AMOUNT OF PRESSURE CAN
cavities 4 and 5. PENETRATE SKIN CAUSING PERSONAL
If all connections are proper between the INJURY OR DEATH. INSPECT FOR
DRBIIIt and the vehicle or other devices, and the HIGH-PRESSURE FUEL LEAKS WITH A
vehicle battery is fully charged, an inoperative SHEET OF CARDBOARD. WEAR SAFETY
DRBIIIt may be the result of a faulty cable or GOGGLES AND ADEQUATE PROTECTIVE
vehicle wiring. For a blank screen, refer to the CLOTHING WHEN SERVICING FUEL
appropriate diagnostic manual. SYSTEM.
3.4.2 DISPLAY IS NOT VISIBLE WARNING: ENGINES PRODUCE CARBON
Low temperatures will affect the visibility of the MONOXIDE THAT IS ODORLESS, CAUSES
display. Adjust the contrast to compensate for this SLOWER REACTION TIME AND CAN LEAD
condition. TO SERIOUS INJURY. WHEN THE ENGINE IS
OPERATING, KEEP SERVICE AREA WELL
VENTILATED OR ATTACH THE VEHICLE
EXHAUST SYSTEM TO THE SHOP EXHAUST
REMOVAL SYSTEM.
Set the parking brake and block the wheels before
testing or repairing the vehicle. It is especially
important to block the wheels on front wheel drive
vehicles; the parking brake does not hold the drive
wheels.
When servicing a vehicle, always wear eye pro-
tection and remove any metal jewelry such as
watchbands or bracelets that might make electrical
contact.
When diagnosing powertrain system problems, it
is important to follow approved procedures where
applicable. These procedures can be found in the
8
GENERAL INFORMATION
service manual. Following these procedures is very – Voltage between any terminal and ground
important to the safety of the individuals perform- must not exceed 500v DC or 500v peak AC.
ing the diagnostic tests. – Use caution when measuring voltage above
25v DC or 25v AC.
4.2.2 VEHICLE PREPARATION FOR – The circuit being tested must be protected by a
TESTING 10 amp fuse or circuit breaker.
Make sure the vehicle being tested has a fully – Use the low current shunt to measure circuits
charged battery. If it does not, false diagnostic codes up to 10 amps. Use the high current shunt to
or error messages may occur. measure circuits exceeding 10 amps.
– When testing for the presence of voltage or
4.2.3 SERVICING SUB-ASSEMBLIES current, make sure the meter is functioning
Some components of the powertrain system are correctly. Take a reading of a known voltage or
intended to be serviced as an assembly only. At- current before accepting a zero reading.
tempting to remove or repair certain system sub- – When measuring current, connect the meter in
components may result in personal injury and/or series with the load.
improper system operation. Only those components – Disconnect the live test lead before disconnect-
with approved repair and installation procedures in ing the common test lead.
the service manual should be serviced.
4.3 WARNINGS AND CAUTIONS
4.2.4 DRBIIIT SAFETY INFORMATION
WARNING: EXCEEDING THE LIMITS OF THE 4.3.1 ROAD TEST WARNINGS
DRBIIIT MULTIMETER IS DANGEROUS. IT Some complaints will require a test drive as part
CAN EXPOSE YOU TO SERIOUS OR of the repair verification procedure. The purpose of
POSSIBLE FATAL INJURY. CAREFULLY the test drive is to try to duplicate the diagnostic
READ AND UNDERSTAND THE CAUTIONS code or symptom condition.
AND SPECIFICATION LIMITS.
Follow the vehicle manufacturer’s service specifi-
CAUTION: Before road testing a vehicle, be
cations at all times. sure that all components are reassembled.
During the test drive, do not hang the DRBIIIT
– Do not use the DRBIIIt if it has been dam-
aged.
from the rear view mirror. Do not attempt to
read the DRBIIIT while driving. Have an
– Do not use the test leads if the insulation is
assistant available to operate the DRBIIIT.
damaged or if metal is exposed.
– To avoid electrical shock, do not touch the test 4.3.2 VEHICLE DAMAGE CAUTIONS
leads, tip or the circuit being tested.
Before disconnecting any control module, make
– Choose the proper range and function for the sure the ignition is off. Failure to do so could
measurement. Do not try voltage or current damage the module. When testing voltage or circuit
measurements that may exceed the rated ca- integrity at any control module, use the terminal
pacity. side (not the wire end) of the harness connector. Do
– Do not exceed the limits shown in the table not probe through the insulation; this will damage
below: it and eventually cause it to fail because of corro-
FUNCTION INPUT LIMIT sion.
Be careful when performing electrical test so as to
Volts 0–500 peak volts AC prevent accidental shorting of terminals. Such a
0–500 volts DC mistake can damage fuses or components. Also, a
Ohms (Resistance)* 0–1.12 megaohms second code could be set, making diagnosis of the
original problem more difficult.
Frequency Measure 0–10 kHz
Frequency Generated
Temperature –58 – +1100°F 5.0 REQUIRED TOOLS AND
–50 – +600°C EQUIPMENT
* Ohms cannot be measured if voltage is present. DRBIIIt (diagnostic read-out box) scan tool
Ohms can be measured only on a non-powered vacuum gauge
circuit. ammeter
9
GENERAL INFORMATION
ohmmeter MAF mass air flow (sensor)
voltmeter
MIL malfunction indicator lamp
jumper wires and probes
oscilloscope ms millisecond(s)
O2 oxygen sensor
6.0 GLOSSARY OF TERMS PDC power distribution center
S/C speed control
A/C air conditioning
SKREEM sentry key remote entry module
APP accelerator pedal position (sensor)
SRC signal range check
BCM body control module WIF water in fuel (sensor)
BP boost pressure (sensor)
CKP crankshaft position (sensor)
CMP camshaft position (sensor)
CTM central timer module
DLC data link connector
ECM engine control module
ECT engine coolant temperature (sensor)
EGR exhaust gas recirculation (solenoid/
valve)
EOS engine oil sensor
IAT intake air temperature (sensor)
IP intake pressure sensor
10
7.0
DIAGNOSTIC INFORMATION AND
PROCEDURES
11
COMMUNICATION
Symptom:
*NO RESPONSE FROM ENGINE CONTROL MODULE
POSSIBLE CAUSES
CHECK POWERS AND GROUNDS TO THE ENGINE CONTROL MODULE
K-ECM CIRCUIT SHORTED TO GROUND
K-ECM CIRCUIT SHORTED TO VOLTAGE
K-ECM CIRCUIT OPEN
ENGINE CONTROL MODULE
TEST ACTION APPLICABILITY

1 Turn the ignition off. All
Disconnect the Engine Control Module harness connectors.
Check each power and ground circuit to the module.
Were any problems found?
Yes → Refer to the wiring diagrams located in the service information to

help isolate an open or shorted condition. Repair as necessary.
Perform ROAD TEST VERIFICATION - VER-2.
No → Go To 2

Disconnect the ECM harness connectors.
Disconnect the DRBIIIt from the DLC.
Measure the resistance between ground and the K-ECM circuit.
Is the resistance below 5.0 ohms?
Yes → Repair the K-ECM circuit for a short to ground.

No → Go To 3

Turn the ignition on.
Using a 12-volt test light connected to ground, probe the K-ECM circuit.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?
Yes → Repair the K-ECM circuit for a short to voltage.

No → Go To 4
12
COMMUNICATION
*NO RESPONSE FROM ENGINE CONTROL MODULE — Continued

Measure the resistance of the K-ECM circuit between the ECM connector and the
DLC.
Yes → Replace and program the Engine Control Module in accordance
with the Service Information.
No → Repair the K-ECM circuit for an open.
13
COMMUNICATION
Symptom:
*NO RESPONSE FROM SENTRY KEY REMOTE ENTRY MODULE
POSSIBLE CAUSES
CHECK POWERS AND GROUNDS TO THE SENTRY KEY REMOTE ENTRY MODULE
K-SKREEM CIRCUIT SHORTED TO GROUND
K-SKREEM CIRCUIT SHORTED TO VOLTAGE
K-SKREEM CIRCUIT OPEN
SENTRY KEY REMOTE ENTRY MODULE

Disconnect the SKREEM harness connector.
Check each power and ground circuit to the module.
Yes → Refer to the wiring diagrams located in the service information to

help isolate an open or shorted condition. Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No → Go To 2

Measure the resistance between ground and the K-SKREEM circuit.
Yes → Repair the K-SKREEM circuit for a short to ground.

No → Go To 3

Using a 12-volt test light connected to ground, probe the K-SKREEM circuit.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Yes → Repair the K-SKREEM circuit for a short to voltage.

No → Go To 4
14
COMMUNICATION
*NO RESPONSE FROM SENTRY KEY REMOTE ENTRY MODULE —

Continued
Measure the resistance of the K-SKREEM circuit between the SKREEM connector
and the DLC.
Yes → Replace and program the Sentry Key Remote Entry Module in
accordance with the Service Information.
No → Repair the K-SKREEM circuit for an open.
15
Symptom List:
P-1105 ATMOSPHERIC PRESSURE SENSOR PLAUSIBILITY WITH
BOOST PRESSURE SENSOR
P1105-ATMOSPHERIC PRESSURE SENSOR SIGNAL VOLTAGE
TOO HIGH
P1105-ATMOSPHERIC PRESSURE SENSOR SIGNAL VOLTAGE
TOO LOW
P1617- ECM READ/WRITE ERROR
P1617- ECM WRITE ERROR
P1617-ECM INCORRECT VALUE
P1617-ECM READ ERROR
P2122-INTERNAL ERROR COUNTER FAULT
P2122-INTERNAL ERROR ENGINE SHUT OFF
P2122-INTERNAL ERROR ENGINE VOLTAGE MONITORING
P2122-INTERNAL ERROR ENGINE VOLTAGE MONITORING
P2123-INJECTOR BANK ERROR
P2124-INJECTOR BANK ERROR
P2139-ECM INJECTOR OUTPUT STAGE #1
P2139-ECM INJECTOR OUTPUT STAGE #1 SHORT CIRCUIT
P2140-ECM INJECTOR OUTPUT STAGE #2
P2140-ECM INJECTOR OUTPUT STAGE #2 SHORT CIRCUIT
P2149-ECM A/D CONVERTER HIGH
P2149-ECM A/D CONVERTER LOW
P2149-ECM A/D CONVERTER PLAUSIBILITY
P2153-STARTER RELAY CIRCUIT ECM THERMAL OVERLOAD
P2197-FUEL QUANTITY SOLENOID ECM THERMAL OVERLOAD
P2214-CAN MESSAGE ERROR
P2319-ECM INTERNAL ERROR 1
P2323-ECM INTERNAL ERROR
P2324-ECM INJECTOR MONITORING 1
P2324-ECM INJECTOR UNDERVOLTAGE
P2340-ECM INJECTION QUANTITY ERROR
16

BOOST PRESSURE SENSOR — Continued
P2350-INTERNAL VOLTAGE ERROR
P2352-INJECTION FAULT - EXCESSIVE TEMPERATURE
P2352-INJECTION FAULT - QUANTITY ERROR
P2352-INJECTION FAULT - TORQUE LIMIT
P2352-INJECTION FAULT EXCESSIVE ENGINE SPEED
P2354-ECM INTERNAL FAULT
P2500-FUEL PRESSURE SOLENOID CIRCUIT EXCESSIVE CUR-
RENT
P2514-CRANKCASE VENT HEATER EXCESSIVE CURRENT
P2526-BOOST PRESSURE SERVO MOTOR EXCESSIVE CURRENT
P2527-EGR VALVE EXCESSIVE CURRENT
Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P-1105 ATMOSPHERIC PRES-
SURE SENSOR PLAUSIBILITY WITH BOOST PRESSURE
SENSOR.
When Monitored and Set Condition:
P1105-ATMOSPHERIC PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH

When Monitored: With the ignition on.
Set Condition: The ECM internal Atmospheric Pressure Sensor is faulty.
P1105-ATMOSPHERIC PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW

Set Condition: The ECM internal Atmospheric Pressure Sensor is faulty.
P2500-FUEL PRESSURE SOLENOID CIRCUIT EXCESSIVE CURRENT

Set Condition: The ECM detects an open or short to ground on the Fuel Pressure Solenoid
Control circuit.
POSSIBLE CAUSES
INTERMITTENT CONDITION
17

BOOST PRESSURE SENSOR — Continued
1 NOTE: If the ECM detects and stores a DTC, the ECM also stores the All
engine/vehicle operating conditions under which the DTC was set. Some of
these conditions are displayed on the DRB at the same time the DTC is
displayed.
NOTE: Before erasing stored DTCs, record these conditions. Attempting to
duplicate these conditions may assist when checking for an active DTC.
NOTE: If there are other DTC’s set with this DTC repair other DTC’s before
continuing with this diagnostic procedure.
NOTE: This DTC indicates an internal ECM problem except in the case of
DTC P2352 where it may indicate a fuel injector problem. Using the Service
Information, check the fuel injectors for leakage before replacing the ECM.
NOTE: This code can be caused by an intermittent problem in the wiring
and connectors to the Engine Control Module. Inspect the Engine Control
Module harness connector and associated wiring for signs of poor terminal
contact.
With the DRBIIIt, erase ECM DTCs.
Perform several engine run cycles, turning the ignition off for at least 20 seconds
between each engine run cycle.
With the DRBIIIt, read the ECM DTCs.
Did this DTC set again?

No → Go To 2
2 WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A All

DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?
Yes → Repair as necessary.

No → Test Complete.
18
Symptom List:
P0100-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW
P2011-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO
HIGH
LOW
P2024-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO HIGH
P2065-MASS AIR FLOW SENSOR SUPPLY VOLTAGE TOO HIGH
P2065-MASS AIR FLOW SENSOR SUPPLY VOLTAGE TOO LOW
P2067-MASS AIR FLOW SENSOR SIGNAL CIRCUIT OPEN OR
SHORTED
P2068-MASS AIR FLOW SENSOR PLAUSIBILITY SIGNAL RATIO
ERROR
P2633-MAF SENSOR SIGNAL PLAUSIBILITY
The title for the tests will be P0100-MASS AIR FLOW SENSOR
SIGNAL VOLTAGE TOO LOW.

Set Condition:

Set Condition:
P2011-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO HIGH

Set Condition: The ECM detects a rationality problem with the MAF Sensor signal.
P2011-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO LOW

Set Condition: The ECM detects a rationality problem with the MAF Sensor signal.
19
P0100-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW —

Continued

Set Condition:

Set Condition:

Set Condition: The Mass Air Flow Sensor Signal voltage is above 4.8 volts.

Set Condition: The Mass Air Flow Sensor Signal voltage is below 0.2 volt.
P2068-MASS AIR FLOW SENSOR PLAUSIBILITY SIGNAL RATIO ERROR

Set Condition: The ECM detects a rationality problem with the MAF Sensor.
POSSIBLE CAUSES
12 VOLT SUPPLY CIRCUIT OPEN
CHECKING THE ENGINE CONTROL RELAY SYSTEM
ECM - 5-VOLT SUPPLY CIRCUIT
MASS AIRFLOW SENSOR
SENSOR GROUND OPEN
MAF SENSOR 5 VOLT SUPPLY CIRCUIT OPEN
MAF SENSOR SIGNAL CIRCUIT OPEN
MAF 5 VOLT SUPPLY CIRCUIT SHORTED TO THE SENSOR GROUND CIRCUIT
MAF SENSOR SIGNAL CIRCUIT SHORTED TO GROUND
ECM SENSOR GROUND CIRCUIT OPEN
MAF SENSOR 5 VOLT SUPPLY CIRCUIT SHORTED TO GROUND
MAF SENSOR SIGNAL CIRCUIT SHORTED TO THE SENSOR GROUND CIRCUIT
MAF SENSOR 5 VOLT SUPPLY CIRCUIT SHORTED TO VOLTAGE
MAF SENSOR CIRCUIT SHORTED TO VOLTAGE
20

Continued
1 NOTE: If DTC P1611, P2306 or P2332 is present with this DTC, diagnose All
DTCs P1611, P2306 or P2332 before diagnosing this DTC.
NOTE: Inspect all air intake and turbocharger related tubes for damage,
restriction or poor connection. Any of these conditions can cause a this DTC
to set.
NOTE: If the ECM detects and stores a DTC, the ECM also stores the
displayed.
With the DRBIIIt, erase the ECM DTCs.
Test drive the vehicle.
Does the DRB III display a Mass Air Flow Sensor DTC?
Yes → Go To 2
No → Go To 16
2 NOTE: Check the ECM for other ECM DTC’s related to circuits that are All
open, shorted to ground or low voltage problems.
Does the DRB also display these type of DTC’s?
Yes → Go To 3
No → Go To 4

Connect a jumper wire between ground and the Engine Control Relay Signal circuit
in ECM C2 harness connector cavity 44.
Using a 12-volt test light connected to ground, check the Fused Engine Control Relay
Output circuits at the ECM C1 harness connector cavities 1, 3 and 5.
Does the test light illuminate brightly for each circuit?
Yes → Go To 4
No → Refer to symptom list and perform Checking the ECM Power and
Grounds.
4 NOTE: A malfunctioning EGR system can cause this DTC to set. Refer to All
symptom Checking the EGR System in the Driveability category to check
EGR system operation.
Turn the ignition off.
Disconnect the MAF Sensor harness connector.
Measure the voltage of the MAF Sensor 5 Volt Supply circuit in MAF Sensor harness
connector.
Is the voltage between 4.8 and 5.2 volts?
Yes → Go To 5
No → Go To 12
21

Continued
Remove the Engine Control Relay.
Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay
connector.
Measure the voltage of the MAF Sensor Signal circuit.
Is the voltage above 1.0 volt?
Yes → Repair the MAF Sensor Signal circuit for a short to voltage.
No → Go To 6

Measure the resistance of the MAF Sensor Signal circuit.
Yes → Go To 7
No → Repair the MAF Sensor Signal circuit for an open

Measure the resistance between ground and the MAF Sensor Signal circuit.
Is the resistance below 1000 ohms?
Yes → Repair the MAF Sensor Signal circuit for a short to ground.
No → Go To 8

Measure the resistance between the MAF Sensor Signal circuit and the Sensor
Ground circuit at of the MAF Sensor harness connector.
Yes → Repair the MAF Sensor Signal for a short to Sensor Ground .
No → Go To 9

Measure the resistance of the Sensor Ground circuit between the MAF Sensor and
the ECM.
Yes → Go To 10
No → Repair the Sensor Ground circuit for an open.
22

Continued
Measure the voltage between the 5-volt Supply circuit and the Sensor Ground circuit
at the MAF Sensor harness connector.
Is the voltage above 4.5 volts?
Yes → Go To 11
No → Replace and program the ECM in accordance with the Service

Information.

Using a 12-volt test light connected to ground, probe the 12 Volt Supply circuit in the
MAF Sensor harness connector
Yes → Replace the MAF Sensor.
No → Repair the 12 Volt Supply circuit for an open.

Measure the resistance of the 5 Volt Supply circuit.
Yes → Go To 13
No → Repair the MAF Sensor 5 Volt Supply circuit for an open.

Measure the resistance between the MAF Sensor 5 Volt Supply circuit and the Sensor
Ground circuit at the MAF Sensor harness connector.
Is the resistance above 1000 ohms?
Yes → Go To 14
No → Repair the MAF 5 Volt Supply circuit for a short to the Sensor
Ground circuit.

Measure the resistance between ground and the MAF Sensor 5 Volt Supply circuit at
the MAF harness connector.
Yes → Repair the MAF Sensor 5 Volt Supply circuit for a short to ground.
No → Go To 15
23

Continued
connector.
Measure the voltage of the MAF Sensor 5 Volt Supply circuit in the ECM harness
connector.
Yes → Repair the MAF Sensor 5 Volt Supply circuit for a short to voltage.
No → Replace and program the Engine Control Module in accordance


With the engine running and at normal operating temperature, monitor the DRB

24
Symptom List:
P0105-INTAKE PRESSURE SENSOR CAN MESSAGE ERROR
P0105-INTAKE PRESSURE SENSOR PLAUSIBILITY
The title for the tests will be P0105-INTAKE PRESSURE
SENSOR CAN MESSAGE ERROR.
POSSIBLE CAUSES
AIR FILTER
AIR RESTRICTION
CAN BUS COMMUNICATION DTCS
HIGH RESISTANCE IN THE INTAKE PRESSURE SENSOR SIGNAL CIRCUIT
HIGH RESISTANCE IN THE INTAKE PRESSURE SENSOR GROUND CIRCUIT
CAN BUS CIRCUITS OPEN TO THE SHIFTER MODULE
HIGH RESISTANCE IN THE INTAKE PRESSURE SENSOR 5-VOLT SUPPLY CIRCUIT

displayed.
With the DRB, erase ECM DTCs.
Turn the ignition off, wait 30 seconds.
With the DRB, read ECM DTCs.
Yes → Go To 2
No → Go To 9

Remove and inspect the Air Filter for soiling or excessive dirt and debris which may
cause air flow restriction.
Were any of these problems found?
Yes → Replace the Air Filter element.

No → Go To 3
25
P0105-INTAKE PRESSURE SENSOR CAN MESSAGE ERROR — Continued

3 NOTE: Inspect all air intake and turbocharger related tubes for damage, All
to set.
Inspect all air intake and turbocharger related tubes and connections.
Yes → Repair or replace as necessary.
No → Go To 4
4 With the DRBIIIt, read the active and stored DTCs for the Transmission Control All
Module.
NOTE: Due to capabilities of certain controllers that use the CAN Bus, not
all modules report CAN Bus DTCs.
Is the TCM reporting active or stored CAN Bus communication DTCs related to the
Shifter Module?
Yes → Refer to symptom list to diagnose CAN Bus DTC in the TCM.
No → Go To 5
5 Turn the ignition off to the lock position. All

Disconnect the Shifter Module harness connector.
Disconnect the ECM harness connector.
NOTE: Check connectors - Clean/repair as necessary.
Measure the resistance of both the CAN C Bus (+) circuit and the CAN C Bus (-)
circuit between the Shifter Module harness connector and ECM harness connector.
Is the resistance below 10.0 ohms for each measurement?
Yes → Go To 6
No → Repair the CAN C Bus (+) and/or CAN C Bus (-) circuit for an
open.

Disconnect the Intake Pressure Sensor harness connector.
Measure the resistance of the Intake Pressure Sensor Signal circuit.
Yes → Go To 7
No → Repair the Intake Pressure Sensor Signal circuit for high resis-
tance.

Measure the resistance of the Sensor Ground circuit.
Yes → Go To 8
No → Repair the Intake Pressure Sensor Ground circuit for high resis-
tance.
26
P0105-INTAKE PRESSURE SENSOR CAN MESSAGE ERROR — Continued

Measure the resistance of the Intake Pressure Sensor 5-volt Supply circuit.
No → Repair the Intake Pressure Sensor 5 Volt Supply circuit for high
resistance.

27
Symptom:
P0105-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH

Set Condition: Intake Pressure Sensor Signal voltage is 4.9 volts or greater.
POSSIBLE CAUSES
INTAKE PRESSURE SENSOR GROUND CIRCUIT SHORTED TO VOLTAGE
INTAKE PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE
INTAKE PRESSURE SENSOR GROUND CIRCUIT OPEN
INTAKE PRESSURE SENSOR
POOR CONNECTOR TERMINAL CONTACT
ENGINE CONTROL MODULE (INTERNAL)
ENGINE CONTROL MODULE (SENSOR SIGNAL SHORTED TO VOLTAGE)

displayed.
NOTE: If DTC P1611, P2306 or P2332 is present with this DTC, diagnose
NOTE: Ensure all turbocharger inlet and outlet tubes are connected prop-
erly, without damage and restriction before continuing with this test. Also
ensure the boost pressure servo motor and servo rod are attached and
functioning properly.
NOTE: If a Boost Pressure Servo Motor DTC is present with this DTC,
diagnose that DTC before continuing.
Cycle the ignition key on and off several times, leaving the key on for at least 10
seconds at a time.
Yes → Go To 2
No → Go To 8
28
P0105-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH —

Continued
Measure the voltage between ground and the Intake Pressure Sensor Signal circuit.
Yes → Go To 3
No → Go To 4

connector.
Yes → Repair the Intake Pressure Sensor Signal circuit for a short to
voltage.

connector.
Measure the voltage between ground and the Intake Pressure Sensor Ground circuit.
Yes → Repair the Intake Pressure Sensor Ground circuit for a short to
voltage. Note: The ECM will need to be checked for proper
operation before the repair is completed. A short to voltage on a
ground circuit can damage the ECM.
No → Go To 5
NOTE: If the Sensor Ground circuit had a short to voltage on it, the ECM
could be damaged.

Yes → Go To 6
No → Repair the Intake Pressure Sensor Ground circuit for an open.

29

Continued
NOTE: Ensure all harness connectors are connected.
Measure the voltage of the Intake Pressure Sensor Signal circuit by back probing
ECM harness connector C2, cavity 11.
Yes → Replace the Intake Pressure Sensor.
No → Go To 7
7 Turn the ignition on. All


No → Ensure good terminal contact between the Intake Pressure Sen-

sor harness connector and the sensor. The repair is complete.


30
Symptom:
P0105-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW

Set Condition: Intake Pressure Sensor Signal voltage is 0.2 volt or lower.
POSSIBLE CAUSES
INTAKE PRESSURE SENSOR 5 VOLT SUPPLY CIRCUIT OPEN
INTAKE PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO GROUND
INTAKE PRESSURE SENSOR SIGNAL AND GROUND CIRCUITS SHORTED TOGETHER
INTAKE PRESSURE SENSOR SIGNAL CIRCUIT OPEN

With the DRB, read the Intake Pressure Sensor voltage.
Is the voltage below 0.3 volt?
Yes → Go To 2
No → Go To 8

Measure the voltage between ground and the Intake Pressure Sensor 5-Volt Supply
circuit at the Intake Pressure Sensor harness connector.
Yes → Go To 3
No → Repair the Intake Pressure Sensor 5-Volt Supply circuit for an

open.
31
P0105-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW —

Continued
Connect a jumper wire between the Intake Pressure Sensor Signal circuit and the
Intake Pressure Sensor 5-Volt Supply circuit.
Is the Intake Pressure Sensor voltage above 4.5 volts?

No → Go To 4

Measure the resistance between ground and the Intake Pressure Sensor Signal
circuit.
Yes → Go To 5
No → Repair the Intake Pressure Sensor Signal circuit for a short to

ground.

Measure the resistance between the Intake Pressure Sensor Signal circuit and
Sensor Ground circuit.
Yes → Go To 6
No → Repair the Intake Pressure Sensor Signal circuit for a short to the

Yes → Go To 7
No → Repair the Intake Pressure Sensor Signal circuit for an open.
7 If there are no possible causes remaining, view repair. All
Repair
Replace and program the Engine Control Module in accordance
32

Continued

33
Symptom List:
P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO HIGH
P2063-INTAKE AIR TEMP SENSOR CIRCUIT SIGNAL VOLTAGE
TOO HIGH
The title for the tests will be P0110-INTAKE AIR TEMP
SENSOR SIGNAL VOLTAGE TOO HIGH.
P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO HIGH

Set Condition: The Intake Air Temperature Sensor Signal voltage is above 4.83 volts.
P2063-INTAKE AIR TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH

Set Condition: The Intake Air Temperature Sensor Signal voltage is above 4.83 volts.
POSSIBLE CAUSES
CHECK FOR ACTIVE DTC
INTAKE AIR TEMP SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE
INTAKE AIR TEMP SENSOR GROUND CIRCUIT OPEN
INTAKE AIR TEMP SENSOR SIGNAL CIRCUIT OPEN

displayed.
Turn the ignition off for 10 seconds.
Monitor the DRB for ECM DTCs.
Yes → Go To 2
No → Go To 5
34
P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO HIGH —

Continued
Disconnect the IAT Sensor harness connector.
connector.
Measure the voltage on the IAT Sensor Signal circuit.
Yes → Go To 3
No → Repair the Intake Air Temperature Sensor Signal circuit for a
short to voltage.
NOTE: Remove the jumper wire.

Measure the resistance of the Intake Air Temperature Sensor Signal circuit.
Yes → Go To 4
No → Repair the Intake Air Temperature Sensor Signal circuit for an
open.

Measure the resistance of the Sensor Ground circuit between the ECM harness
connector and the IAT Sensor harness connector.

No → Repair the Intake Air Temperature Sensor Ground circuit for an

open.
35
P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO HIGH —

Continued

36
Symptom List:
P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO LOW
P2063-INTAKE AIR TEMP SENSOR CIRCUIT SIGNAL VOLTAGE
TOO LOW
The title for the tests will be P0110-INTAKE AIR TEMP
SENSOR SIGNAL VOLTAGE TOO LOW.
P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO LOW

Set Condition: The Intake Air Temperature Sensor Signal voltage is below 0.073 volt for
more than 60 seconds.
P2063-INTAKE AIR TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW

Set Condition: The Intake Air Temperature Sensor Signal voltage is below 0.073 volt for
more than 60 seconds.
POSSIBLE CAUSES
IAT SENSOR
INTAKE AIR TEMP SENSOR SIGNAL CIRCUIT SHORTED TO GROUND
INTAKE AIR TEMP SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND

displayed.
Monitor the DRB for ECM DTCs for at least 2 minutes.
Yes → Go To 2
No → Go To 6
37
P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO LOW —

Continued
Monitor the DRB for ECM DTCs for at least 2 minutes.
Does the DRB display P0110 INTAKE AIR TEMP SIGNAL VOLTAGE TOO HIGH?
Yes → Replace the Intake Air Temperature Sensor.
No → Go To 3

Measure the resistance between ground and the Intake Air Temperature Sensor
Signal circuit.
Yes → Go To 4
short to ground.

Measure the resistance between the Intake Air Temperature Sensor Signal circuit
and the Sensor Ground circuit.
Yes → Go To 5
short to the Sensor Ground circuit.

Repair
38
P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO LOW —

Continued

39
Symptom List:
P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT PLAUSIBILITY
The title for the tests will be P0115-ENGINE COOLANT TEMP
SENSOR CIRCUIT PLAUSIBILITY.
POSSIBLE CAUSES
ECT SENSOR
ECT SENSOR - COLD
ECT SENSOR - HOT
HGH RESISTANCE IN ECT SENSOR CIRCUITS
ENGINE COLD TOO LONG

1 Note: The best way to diagnose this DTC is to allow the vehicle to remain All
outside overnight in order to have a completely cold soaked engine.
Note: Extremely cold outside ambient temperatures may cause this DTC to
set.
Verify that the coolant level is correct.
Start the engine.
With the DRBIIIt, set the engine RPM to 1500 and allow the engine to warm up for
10-15 minutes.
With the DRBIIIt, monitor the Engine Coolant Temperature value during the warm
up cycle. Make sure the transition of temperature change is smooth.
Did the engine temperature reach a minimum of 80° C (176° F)?
Yes → Go To 2
No → Refer to the Service Information for cooling system performance
diagnosis. The most probable cause is a Thermostat problem.
Also, refer to any related TSBs.
2 NOTE: The engine temperature must be below 50°C (120°F) for this test. All
NOTE: The thermostat must be operating correctly for this test to be valid.
With the DRBIIIt in Sensors, read and note the engine coolant temperature.
Using a temperature probe, measure the engine block temperature near the ECT
Sensor.
Are the readings within 7°C (13°F) of each other?
Yes → Go To 3
No → Go To 4
40
P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT PLAUSIBILITY —

Continued
3 NOTE: The thermostat must be operating correctly for this test to be valid. All
Start the engine and bring the engine to operating temperature (thermostat open).
Turn the engine off and wait 10 minutes to allow the engine temperature to stabilize.
Sensor.
With the DRBIIIt, select Engine, then Sensors and read the engine coolant
temperature.
Yes → Test Complete.

No → Go To 4
4 Disconnect the ECT harness connector. All

Measure the resistance of the ECT Sensor Signal circuit between the ECM harness
connector and the ECT harness connector.
Yes → Replace the Engine Coolant Temperature Sensor.

No → Repair the ECT Sensor circuit(s) that measured above 10.0 ohms
for high resistance.
41
Symptom:
WITH ENGINE OIL SENSOR
P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT PLAUSIBILITY WITH EN-

GINE OIL SENSOR
When Monitored: With the engine running.
Set Condition: The ECT Sensor signal indicates a different engine temperature than the
EOS Sensor.
POSSIBLE CAUSES
CURRENT DTC
ECT SENSOR
ECT SENSOR - COLD
ECT SENSOR - HOT
ENGINE OIL SENSOR SENSOR
HGH RESISTANCE IN ECT SENSOR CIRCUITS
ENGINE COLD TOO LONG

1 Verify that the coolant level is correct. All
Start the engine.
With the DRBIIIt, set the engine RPM to 1500 and allow the engine to warm up for
10-15 minutes.
With the DRBIIIt, monitor the Engine Coolant Temperature value during the warm
up cycle. Make sure the transition of temperature change is smooth.
Did the engine temperature reach a minimum of 80° C (176° F)?
Yes → Go To 2
No → Refer to the Service Information for cooling system performance

diagnosis. The most probable cause is a Thermostat problem.
Also, refer to any related TSBs.

Did this DTC return after performing the previous test?
Yes → Go To 3
No → Check for possible connecor or wiring problems at the ECT sensor

that may cause an intermittent problem. Repair as necessary.
Test Complete.
42

WITH ENGINE OIL SENSOR — Continued
3 NOTE: The engine temperature must be below 50°C (120°F) for this test. All
With the DRBIIIt in Sensors, read and note the engine coolant temperature.
Sensor.
Yes → Go To 4
No → Go To 5
4 NOTE: The thermostat must be operating correctly for this test to be valid. All
Start the engine and bring the engine to operating temperature (thermostat open).
Turn the engine off and wait 10 minutes to allow the engine temperature to stabilize.
Sensor.
With the DRBIIIt, select Engine, then Sensors and read the engine coolant
temperature.
Yes → Replace the Engine Oil Sensor.
No → Go To 5
5 Disconnect the ECT harness connector. All

Measure the resistance of the ECT Sensor Signal circuit between the ECM harness
Yes → Replace the Engine Coolant Temperature Sensor.
No → Repair the ECT Sensor circuit(s) that measured above 10.0 ohms
for high resistance.
43
Symptom List:
P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLT-
AGE TOO HIGH
AGE TOO HIGH
AGE TOO LOW
The title for the tests will be P0115-ENGINE COOLANT TEMP
SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH.

HIGH
Set Condition: The Engine Coolant Temperature Sensor Signal voltage is above 4.98 volts
for more than 3 seconds.

HIGH
Set Condition: The Engine Coolant Temperature Sensor Signal voltage is above 4.98 volts

LOW
Set Condition:
POSSIBLE CAUSES
ECM ECT SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE
ECT SENSOR GROUND CIRCUIT OPEN
ECT SENSOR
ECT SENSOR SIGNAL CIRCUIT OPEN
44
P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE

TOO HIGH — Continued
1 NOTE: If multiple DTCs are present, the most likely cause is a 5-Volt Supply All
or Sensor Ground circuit shorted to voltage or ground. Refer to the Service
Information Wiring section for circuits that would affect multiple DTCs.
displayed.
With the DRB, monitor the Engine Coolant Temperature (ECT) Sensor voltage.
Is the ECT Sensor voltage above 4.90 volts?
Yes → Go To 2
No → Go To 7

Disconnect the ECT Sensor harness connector.
Measure the voltage on the ECT Sensor Signal circuit.
Yes → Repair the ECT Sensor Signal circuit for a short to voltage.
No → Go To 3

Connect a jumper wire between the ECT Sensor harness connector cavities.
With the DRB, read the ECT Sensor voltage.
Yes → Replace the ECT Sensor in accordance with the Service Informa-
tion.
No → Go To 4

Measure the resistance of the ECT Sensor Ground circuit.
Yes → Go To 5
No → Repair the ECT Sensor Ground circuit for an open.


Measure the resistance of the ECT Sensor Signal circuit.
Yes → Go To 6
No → Repair the ECT Sensor Signal circuit for an open.

45

Repair

46
Symptom:
AGE TOO LOW

LOW
Set Condition: The Engine Coolant Temperature Sensor Signal voltage is below 0.1 volt
POSSIBLE CAUSES
ECT SENSOR
ECT SENSOR SIGNAL CIRCUIT SHORTED TO GROUND
ECT SENSOR SIGNAL AND GROUND CIRCUITS SHORTED TOGETHER

displayed.
With the DRB, monitor the Engine Coolant Temperature (ECT) Sensor voltage.
Is the ECT Sensor voltage below 0.1 volt?
Yes → Go To 2
No → Go To 6

With the DRB, read the ECT Sensor voltage.
Yes → Replace the ECT Sensor in accordance with the Service Informa-
tion.
No → Go To 3
47

TOO LOW — Continued
Measure the resistance between ground and the ECT Sensor Signal circuit.
Yes → Go To 4
No → Repair the ECT Sensor Signal circuit for a short to ground.


Measure the resistance between the ECT Sensor Signal circuit and Sensor Ground
circuit.
Yes → Go To 5
No → Repair the ECT Sensor Signal and Ground circuits for a short
together.

Repair


48
Symptom:
P0180-FUEL TEMPERATURE SENSOR CIRCUIT - SIGNAL VOLT-
AGE TOO HIGH
P0180-FUEL TEMPERATURE SENSOR CIRCUIT - SIGNAL VOLTAGE TOO HIGH

Set Condition: The fuel temperature sensor signal voltage is above 4.7 volts.
POSSIBLE CAUSES
FUEL TEMPERATURE SENSOR GROUND CIRCUIT OPEN
FUEL TEMPERATURE SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE
FUEL TEMPERATURE SENSOR
FUEL TEMPERATURE SENSOR SIGNAL CIRCUIT OPEN

1 NOTE: If multiple DTCs are present, the most likely cause is a 5-Volt Supply All
or Sensor Ground circuit shorted to voltage or ground. Refer to the Service
Information Wiring section for circuits that would affect multiple DTCs.
displayed.
With the DRB, monitor the Fuel Temperature Sensor voltage.
Is the Fuel Temperature Sensor voltage above 4.80 volts?
Yes → Go To 2
No → Go To 6

Disconnect the Fuel Temperature Sensor harness connector.
Measure the voltage on the Fuel Temperature Sensor Signal circuit.
Yes → Repair the Fuel Temperature Sensor Signal circuit for a short to
voltage.
No → Go To 3
49
P0180-FUEL TEMPERATURE SENSOR CIRCUIT - SIGNAL VOLTAGE

Connect a jumper wire between the Fuel Temperature Sensor harness connector
cavities.
With the DRB, read the Fuel Temperature Sensor voltage.
Yes → Replace the Fuel Temperature Sensor in accordance with the

Service Information.
No → Go To 4

Measure the resistance of the Fuel Temperature Sensor Ground circuit.
Yes → Go To 5
No → Repair the Fuel Temperature Sensor Ground circuit for an open.


Measure the resistance of the Fuel Temperature Sensor Signal circuit.
No → Repair the Fuel Temperature Sensor Signal circuit for an open.



50
Symptom List:
P0180-FUEL TEMPERATURE SENSOR CIRCUIT - SIGNAL VOLT-
AGE TOO LOW
P2625-FUEL TEMPERATURE SENSOR PLAUSIBILITY
The title for the tests will be P0180-FUEL TEMPERATURE
SENSOR CIRCUIT - SIGNAL VOLTAGE TOO LOW.
P0180-FUEL TEMPERATURE SENSOR CIRCUIT - SIGNAL VOLTAGE TOO LOW

Set Condition: The fuel temperature sensor signal voltage is below 0.8 volt.
P2625-FUEL TEMPERATURE SENSOR PLAUSIBILITY

Set Condition: The Mass Air Flow Sensor Signal voltage is above 4.8 volts.
POSSIBLE CAUSES
FUEL TEMPERATURE SENSOR SIGNAL CIRCUIT SHORTED TO GROUND
FUEL TEMPERATURE SENSOR SIGNAL AND GROUND CIRCUITS SHORTED TOGETHER

displayed.
With the DRB, monitor the Fuel Temperature Sensor voltage.
Is the Fuel Temperature Sensor voltage below 0.10 volt?
Yes → Go To 2
No → Go To 5
51
P0180-FUEL TEMPERATURE SENSOR CIRCUIT - SIGNAL VOLTAGE

TOO LOW — Continued
With the DRB, read the Fuel Temperature Sensor voltage.
Yes → Replace the Fuel Temperature Sensor in accordance with the
No → Go To 3

Measure the resistance between ground and the Fuel temperature Sensor Signal
circuit.
Yes → Go To 4
No → Repair the Fuel Temperature Sensor Signal circuit for a short to

ground.

Measure the resistance between the Fuel Temperature Sensor Signal circuit and

No → Repair the Fuel Temperature Sensor Signal and Ground circuits
for a short together.


52
Symptom List:
P0190-FUEL PRESS SENSOR CIRCUIT MALF SIGNAL VOLTAGE
TOO HIGH
P2008-FUEL PRESSURE SENSOR CIRCUIT SIGNAL VOLTAGE
TOO HIGH
The title for the tests will be P0190-FUEL PRESS SENSOR
CIRCUIT MALF SIGNAL VOLTAGE TOO HIGH.
P0190-FUEL PRESS SENSOR CIRCUIT MALF SIGNAL VOLTAGE TOO HIGH

Set Condition: The Fuel Rail Pressure Sensor Signal voltage is above 4.8 volts.
POSSIBLE CAUSES
ECM - FUEL PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE
ECM - FUEL PRESSURE SENSOR SIGNAL OPEN
FUEL PRESSURE SENSOR SIGNAL CIRCUIT OPEN
FUEL PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE
SENSOR GROUND CIRCUIT OPEN
FUEL PRESSURE SENSOR 5-VOLT SUPPLY CIRCUIT OPEN
SENSOR GROUND CIRCUIT SHORTED TO VOLTAGE
FUEL PRESSURE SENSOR
53
P0190-FUEL PRESS SENSOR CIRCUIT MALF SIGNAL VOLTAGE TOO

HIGH — Continued
1 WARNING: THE FUEL INJECTION PUMP SUPPLIES HIGH-PRESSURE All
FUEL TO EACH INDIVIDUAL INJECTOR THROUGH HIGH-PRESSURE
FUEL LINES. FUEL UNDER HIGH PRESSURE CAN PENETRATE SKIN
AND CAUSE PERSONAL INJURY. WEAR SAFETY GOGGLES AND ADE-
QUATE PROTECTIVE CLOTHING.
displayed.
seconds at a time.
Yes → Go To 2
No → Go To 10

Disconnect the Fuel Pressure Sensor harness connector.
Measure the voltage of the Fuel Pressure Sensor Signal circuit.
Select the appropriate voltage reading.
Voltage is above 5.4 volts.

Go To 3
Voltage is between 4.7 and 5.4 volts.

Go To 4
Voltage is below 4.7 volts.

Go To 9

connector.

No → Repair the Fuel Pressure Sensor Signal circuit for a short to

voltage.
54

HIGH — Continued
Yes → Go To 5


Measure the resistance of the Fuel Pressure Sensor 5-Volt Supply circuit.
Yes → Go To 6
No → Repair the Fuel Pressure Sensor 5-volt Supply circuit for an open.

connector.
Measure the voltage of the Sensor Ground circuit at the Fuel Pressure Sensor and
ECM harness connectors.
Is the voltage above 1.0 volt at either connector?
Yes → Repair the Sensor Ground circuit for a short to voltage.
No → Go To 7
NOTE: If the Sensor Ground circuit had a short to voltage on it, the ECM
could be damaged. Retest the Fuel Pressure Sensor circuit.

Connect a jumper wire between the Fuel Pressure Sensor Signal circuit and the
Sensor Ground circuit in the Fuel Pressure Sensor harness connector.
Turn the ignition on and monitor the DRB for DTCs.
Is DTC P0190 FUEL PRESS SENSOR CIRCUIT MALF SIGNAL VOLTAGE TOO
LOW present?
Yes → Replace the Fuel Pressure Sensor.

No → Go To 8
Repair
55

HIGH — Continued
Measure the resistance of the Fuel Pressure Sensor Signal circuit.
No → Repair the Fuel Pressure Sensor Signal circuit for an open.



56
Symptom List:
P0190-FUEL PRESS SENSOR CIRCUIT MALF SIGNAL VOLTAGE
TOO LOW
P2008-FUEL PRESSURE SENSOR CIRCUIT SIGNAL VOLTAGE
TOO LOW
The title for the tests will be P0190-FUEL PRESS SENSOR
CIRCUIT MALF SIGNAL VOLTAGE TOO LOW.
P0190-FUEL PRESS SENSOR CIRCUIT MALF SIGNAL VOLTAGE TOO LOW

Set Condition: The Fuel Rail Pressure Sensor Signal voltage is below 0.2 volt.
POSSIBLE CAUSES
FUEL PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO GROUND
FUEL PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND
ECM - FUEL PRESSURE SENSOR SIGNAL SHORTED TO GROUND

1 WARNING: THE FUEL INJECTION PUMP SUPPLIES HIGH-PRESSURE All
FUEL TO EACH INDIVIDUAL INJECTOR THROUGH HIGH-PRESSURE
FUEL LINES. FUEL UNDER HIGH PRESSURE CAN PENETRATE SKIN
AND CAUSE PERSONAL INJURY. WEAR SAFETY GOGGLES AND ADE-
QUATE PROTECTIVE CLOTHING.
displayed.
seconds at a time.
Yes → Go To 2
No → Go To 6
57

LOW — Continued
Yes → Replace the Fuel Pressure Sensor.
No → Go To 3

Measure the resistance between ground and the Fuel Pressure Sensor Signal circuit.
Yes → Go To 4
No → Repair the Fuel Pressure Sensor Signal circuit for a short to
ground.

Measure the resistance between the Sensor Ground circuit and the Fuel Pressure
Sensor Signal circuit.
Yes → Go To 5
No → Repair the Fuel Pressure Sensor Signal circuit for a short to the
Repair
58

LOW — Continued

59
Symptom List:
P0201-CYLINDER 1-INJECTOR CIRCUIT EXCESSIVE CURRENT
P0201-CYLINDER 1-INJECTOR CIRCUIT OPEN OR SHORTED TO
GROUND
P0201-CYLINDER 1-INJECTOR CIRCUIT SHORTED TO GROUND
P0201-CYLINDER 1-INJECTOR CIRCUIT SHORTED TO VOLTAGE
GROUND
GROUND
GROUND
GROUND
P2123-INJECTOR CIRCUIT FAULT
P2123-INJECTOR CIRCUIT LOW SIDE SHORTED TO GROUND
P2123-INJECTOR CIRCUIT SHORTED TO GROUND OR VOLTAGE
P2124-INJECTOR CIRCUIT FAULT
P2124-INJECTOR CIRCUIT LOW SIDE SHORTED TO GROUND
P2124-INJECTOR CIRCUIT SHORTED TO GROUND OR VOLTAGE
P2141-CYLINDER #1 INJECTOR OPEN CIRCUIT
The title for the tests will be P0201-CYLINDER 1-INJECTOR
CIRCUIT EXCESSIVE CURRENT.
60
P0201-CYLINDER 1-INJECTOR CIRCUIT EXCESSIVE CURRENT —

Continued

Set Condition: The ECM detects excessive current through the Cylinder #1 Injector
driver when on.
P0201-CYLINDER 1-INJECTOR CIRCUIT OPEN OR SHORTED TO GROUND

Set Condition: The ECM detects an open or short to ground on the Cylinder #1 Injector
circuit.

Set Condition: The ECM detects a short to ground on the Cylinder #1 Injector circuit.

Set Condition: The ECM detects a short to voltage on the Cylinder #1 Injector circuit.

driver when on.

circuit.



driver when on.
61

Continued

circuit.



driver when on.

circuit.



driver when on.

circuit.
62

Continued


POSSIBLE CAUSES
CHECKING ECM POWER AND GROUNDS
FUEL INJECTOR CONTROL CIRCUIT SHORTED TO VOLTAGE
FUEL INJECTOR CONTROL CIRCUIT SHORTED TO GROUND
FUEL INJECTOR CIRCUITS SHORTED TOGETHER
FUEL INJECTOR CONTROL CIRCUIT OPEN
FUEL INJECTOR

displayed.
Attempt to start the engine and test drive the vehicle.
Yes → Go To 2
No → Go To 8
63

Continued
Connect a jumper wire between ground and the Engine Control Relay Control circuit
Choose the appropriate result.
Test light is on for all circuits.

Go To 3
Test light is on for 1 or 2 circuits
Repair the Engine Control Relay Output circuit(s) that did not
illuminate brightly for an open.
Light off for all circuits.
Refer to symptom Checking the ECM Power and Grounds.

Disconnect all of the Cylinder Fuel Injector harness connectors.
Remove the Engine Control Relay from Fuse Block No.1
connector in Fuse Block No.1.
Measure the voltage of all of the Fuel Injector Control circuit.
Is the voltage above 1.0 volt for any of the measurements?
Yes → Repair the appropriate Fuel Injector Control circuit for a short to
voltage.
No → Go To 4

Disconnect all of the Fuel Injector harness connectors.
Measure the resistance between ground and all of the Fuel Injector Control circuit.
Is the resistance below 1000 ohms for any of the measurements?
Yes → Repair the Fuel Injector Control circuit for a short to ground.
No → Go To 5

Measure the resistance between Fuel Injector No. 1 harness connector cavities 1 and
2.
Repeat the previous step for injectors 2, 3, 4, and 5.
Is the resistance below 1000 ohms for any of the measurements?
Yes → Repair the Fuel Injector Control circuit and Common Driver
circuit for a short together.
No → Go To 6
64

Continued
Measure the resistance of each Fuel Injector Control circuit between its respective
injector harness connector and the ECM harness connector.
Yes → Go To 7
No → Repair the appropriate Fuel Injector Control circuit for an open.


Replace the Cylinder Fuel Injector that was identified in the DTC in accordance with
the Service Information.
Does the DRBIIIt display this DTC?
No → The repair is complete.


65
Symptom List:
P0300-MISFIRE DETECTED
P2113-MISFIRE CYLINDER #1
P2567-LEAKAGE CYLINDER #1
P2573-GENERAL LEAKAGE
P2574-INJECTOR 1 INJECTION TIME ABOVE LIMIT
P2574-INJECTOR 1 INJECTION TIME BELOW LIMIT
The title for the tests will be P0300-MISFIRE DETECTED.
P0300-MISFIRE DETECTED
Set Condition: The ECM detects multiple misfires from one or more cylinders.
POSSIBLE CAUSES
CHECKING FOR FUEL LEAKAGE
CHECKING INJECTOR CLASSIFICATION
66
P0300-MISFIRE DETECTED — Continued
POSSIBLE CAUSES
CORRECTION QUANTITY CHECK
CYLINDER SPEED CHECK
ENGINE COMPRESSION
INJECTOR LEAKAGE

displayed.
Test drive the vehicle and attempt to duplicate the problem.
With the DRB, read ECM DTC’s.
Yes → Go To 2
No → Go To 8
2 Start and idle the engine for 5 minutes. All

Inspect the fuel rail, fuel pressure sensor, fuel pressure solenoid and all fuel injectors
for evidence of fuel leakage.
Is there fuel leakage near any of the injectors or the fuel rail?
Yes → Refer to the Service Information to repair fuel leakage.

No → Go To 3

With the DRBIIIt, perform the Cylinder Compression Test.
Is the cylinder compression within specification for all cylinders?
Yes → Go To 4
No → Repair as necessary in accordance with the Service Information.

Read and note the six-digit code located on the top of each injector.
With the DRBIIIt, check the current programmed injector classifications to the
six-digit codes from the vehicles current fuel injectors.
Are all of the Fuel Injectors classified correctly?
Yes → Go To 5
No → Using the DRB III, reset injectors to correct classification.
67
P0300-MISFIRE DETECTED — Continued

5 With the DRBIIIt, select System Test, Smooth Eng Run Check, then Correction All
Quantity Check.
Perform this test at Idle, 2000 rpm and 3000 rpm.
NOTE: Readings per cylinder should be below ± 0.00450 mm3/stroke for each
cylinder at each engine speed.
Did any of the cylinders exceed ± 0.00450 mm3/stroke during this test?
Yes → Replace Fuel Injector of the cylinder(s) that had readings above ±
0.00450 mm3/stroke.
No → Go To 6
6 With the DRBIIIt, select System Test, Smooth Eng Run Check, then Cylinder Speed All
Check.
NOTE: Readings for all cylinders should be close to each other. Look for one
or two cylinders to differ high or low from the other cylinders.
Did any of the cylinders differ significantly from the majority of the other cylinders?
Yes → Replace Fuel Injector of the cylinder(s) that had readings signif-
icantly above or below the other fuel injectors.
No → Go To 7

Perform the INJECTOR LEAKAGE TEST in accordance with the Service Informa-
tion.
Yes → Repair or replace as necessary in accordance with the Service
Information.

68
Symptom:
P0500-WHEEL SPEED SENSOR PLAUS - CAN BUS MESSAGE FROM
ABS
P0500-WHEEL SPEED SENSOR PLAUS - CAN BUS MESSAGE FROM ABS

Set Condition: The Boost Pressure Sensor Signal voltage exceeds 4.85 volts for at least 2
seconds.
POSSIBLE CAUSES
CHECK FOR RELATED CONTROLLER ANTILOCK BRAKES DTCS
CHECK FOR RELATED TRANSMISSION CONTROL MODULE DTCS

1 NOTE: If the ECM displays multiple CAN Bus related DTC’s, check the CAN All
Bus circuits at the ECM harness connector for proper connection before
continuing with this test.
displayed.
With the DRB, read the ECM DTC’s.
Does the DRB display this DTC?
Yes → Go To 2
No → Go To 4

With the DRB, check for Controller Antilock Brakes DTCs.
NOTE: The ECM Receives vehicle speed messages via CAB Bus from the ABS
module. An interruption on the CAN Bus can cause this fault to set.
Are any related CAB DTCs present?
Yes → Refer to symptom list for problems related to CAB DTCs before
continuing.
No → Go To 3
69
P0500-WHEEL SPEED SENSOR PLAUS - CAN BUS MESSAGE FROM ABS

— Continued
3 NOTE: The TCM Receives vehicle speed messages via CAB Bus from the ABS All
module. An interruption on the CAN Bus can cause this fault to set.
With the DRB, check the TCM for DTCs.
Are any ABS CAN Bus Message or Vehicle Speed related TCM DTCs present?
Yes → Replace the CAB in accordance with the Service Information.



70
Symptom:
P0600-CAN DATA BUS - BUS CIRCUIT FAULT
P0600-CAN DATA BUS - BUS CIRCUIT FAULT

Set Condition: The ECM detects an open, short to ground or short to voltage on the CAN
Bus circuit.
POSSIBLE CAUSES
CAN BUS COMMUNICATION DTCS
CAN BUS CIRCUITS OPEN TO TCM

displayed.
Yes → Go To 2
No → Go To 4
2 With the DRBIIIt, read the active and stored DTCs for all modules that use CAN Bus All
communication.
NOTE: Due to capabilities of certain controllers that use the CAN Bus, not
all modules report CAN Bus DTCs.
NOTE: If a total CAN Bus failure transpires, there will be multiple CAN Bus
DTCs present in many modules. If the other modules are reporting Engine
CAN Bus message faults or DTC’s related to ECM CAN messages ONLY,
answer No for the following question.
Are other modules reporting active or stored CAN Bus communication DTCs?
Yes → Refer to symptom list for problems related to CAN Bus Failure.
No → Go To 3
71
P0600-CAN DATA BUS - BUS CIRCUIT FAULT — Continued

3 Turn the ignition off to the lock position. All
Disconnect the TCM C2 harness connector.
Disconnect the ECM harness connector.
NOTE: Check connectors - Clean/repair as necessary.
Measure the resistance of both the CAN C Bus (+) circuit and the CAN C Bus (-)
circuit between the TCM C2 harness connector and ECM harness connector.
Yes → Replace the Engine Control Module in accordance with the

No → Repair the CAN C Bus (+) and/or CAN C Bus (-) circuit for an
open.

72
Symptom List:
P1222-ACC PEDAL POSITION SENSOR 1 CKT PLAUSIBILITY
P1222-ACC PEDAL POSITION SENSOR 1 CKT SIGNAL VOLTAGE
TOO HIGH
TOO LOW
P1234-ACC PEDAL POSITION SENSOR 2 CIRCUIT PLAUSIBILITY
TOO HIGH
TOO LOW
P2327-APP SENSOR PLAUSIBILITY
The title for the tests will be P1222-ACC PEDAL POSITION
SENSOR 1 CKT PLAUSIBILITY.
POSSIBLE CAUSES
ACCELERATOR PEDAL POSITION SENSOR
ECM - APP SENSOR 1 5-VOLT SUPPLY CIRCUIT
SENSOR GROUND OPEN (APP SENSOR)
APP SENSOR 5-VOLT SUPPLY CIRCUIT OPEN
APP SENSOR SIGNAL CIRCUIT OPEN
APP SENSOR 5-VOLT SUPPLY CIRCUIT SHORTED TO SENSOR GROUND
APP SENSOR SIGNAL CIRCUIT SHORTED TO GROUND
APP SENSOR 5-VOLT SUPPLY CIRCUIT SHORTED TO GROUND
VERIFY APP SENSOR OPERATION
APP SENSOR SIGNAL CIRCUIT SHORTED TO THE SENSOR GROUND CIRCUIT
APP SENSOR 5-VOLT SUPPLY CIRCUIT SHORTED TO VOLTAGE
ECM - SENSOR GROUND OPEN
APP SENSOR CIRCUIT SHORTED TO VOLTAGE
APP SENSOR GROUND CIRCUIT SHORTED TO VOLTAGE
ECM - APP SENSOR SIGNAL CIRCUIT
73
P1222-ACC PEDAL POSITION SENSOR 1 CKT PLAUSIBILITY — Continued

displayed.
NOTE: The APP Sensor is a device that contains 2 separate potentiometer
type sensors. Each sensor has its own 5-volt supply circuit, sensor ground
circuit and signal circuit. The APP Sensor no longer incorporates a low-idle
switch.
NOTE: The APP Sensor 2 signal should always be approximately 1/2 the
voltage of the APP Sensor 1 signal.
Using a voltmeter, backprobe the APP Sensor 1 and APP Sensor 2 Signal circuits at
the APP Sensor harness connector with the accelerator pedal in the at rest position.
Is the voltage between 0.28 and 0.37 volt for sensor 1 and 0.10 and 0.19 volt for sensor
2?
Yes → Go To 2
No → Go To 5

Fully depress the accelerator pedal.
Using a voltmeter backprobe the APP Sensor harness connector and read the voltage
for APP Sensor 1 and APP Sensor 2 Signal circuits.
Is the voltage between 4.45 and 4.75 volts for #1 and 2.15 and 2.45 volts for #2?
Yes → Go To 3
No → Go To 5

With the DRB, read the APP Sensor 1 and APP Sensor 2 percentages (%).
With the accelerator pedal in the idle position, slowly depress the accelerator pedal
until the pedal is fully depressed.
NOTE: The percentage readings for APP Sensors 1 and 2 should increase
smoothly as the pedal is depressed.
NOTE: This test can also performed using a voltmeter by back probing each
APP Sensor Signal circuit at the APP Sensor harness connector and
observing the voltmeter for a smooth voltage change through the entire
pedal travel.
Does the percentage (voltage) increase smoothly for both readings with the acceler-
ator pedal travel?
Yes → Go To 4
No → Replace the Accelerator Pedal Position Sensor in accordance with

74

conditions under which the DTC was set by slowly pressing and releasing the
accelerator pedal several times.

5 NOTE: Perform the rest of this diagnostic procedure on the individual APP All
Sensor Potentiometer (1 or 2) that did not display the correct voltages in the
previous test.
Disconnect the APP Sensor harness connector.
Measure the voltage of the 5-Volt Supply circuit in the APP Sensor harness connector.
Yes → Go To 6
No → Go To 14

Connect a jumper wire between APP Sensor Signal circuit and the 5-volt supply
circuit at the APP Sensor harness connector .
With the DRB, read the PEDAL OUTPUT VOLTS.
Does the DRB display between 4.0 and 5.5 volts?
Yes → Go To 7
No → Go To 10

connector.
Measure the voltage of the APP Sensor Ground circuit.
Yes → Repair the App Sensor Ground circuit for a short to voltage.
No → Go To 8
75

Measure the resistance of the Sensor Ground circuit between the APP Sensor and the
ECM.
Yes → Go To 9
No → Repair the APP Sensor Ground circuit for an open.


Using a 12-volt test light connected to 12-volts, check the Sensor Ground circuit of
the appropriate potentiometer.
Yes → Replace the Accelerator Pedal Position Sensor.


Measure the resistance of the APP Sensor Signal circuit.
Yes → Go To 11
No → Repair the APP Sensor Signal circuit for an open

Measure the resistance between ground and the APP Sensor Signal circuit.
Yes → Repair the APP Sensor Signal circuit for a short to ground.
No → Go To 12

Measure the resistance between the APP Sensor Signal circuit and the Sensor
Ground circuit at the APP Sensor harness connector.
Yes → Repair the APP Sensor Signal and Sensor Ground circuits for a
short together.
No → Go To 13
76

connector.
Measure the voltage of the APP Sensor Signal circuit.
Yes → Repair the APP Sensor Signal circuit for a short to voltage.


Measure the resistance of the Accelerator Pedal Position Sensor 5-volt Supply circuit.
Yes → Go To 15
No → Repair the Accelerator Pedal Position Sensor 5-Volt Supply circuit
for an open.

Measure the resistance between the Accelerator Pedal Position Sensor 5-Volt Supply
circuit and both Sensor Ground circuits in the APP Sensor harness connector.
Yes → Go To 16
No → Repair the 5-Volt Supply circuit for a short to the Sensor Ground
circuit.

Measure the resistance between ground and the Accelerator Pedal Position Sensor
5-volt Supply circuit.
Yes → Repair the Accelerator Pedal Position Sensor 5-Volt Supply circuit
for a short to ground.
No → Go To 17
77

connector.
Measure the voltage of the Accelerator Pedal Position Sensor 5-Volt Supply circuit in
the ECM harness connector.
Yes → Repair the Accelerator Pedal Position Sensor 5-Volt Supply circuit
for a short to voltage.

78
Symptom:
P1480-GLOW PLUG INDICATOR ERROR
P1480-GLOW PLUG INDICATOR ERROR

When Monitored: Witth the ignition on.
Set Condition: the ECM recieves a glow plug inidcator error message from the instru-
ment cluster over the CAN Bus.
POSSIBLE CAUSES
VERIFY CURRENT DTC

Perform several ignition key cycles leaving the ignition on for 10 seconds, then off for
10 seconds.
Yes → Refer Refer to Instrument Cluster information for the related
symptom(s).
79
Symptom List:
P1482-GLOW PLUG MODULE - COMMUNICATION ERROR
P2537-GLOW PLUG CONTROL CIRCUIT PREGLOW FAULT
P2537-GLOW PLUG CONTROL CIRCUIT PREGLOW SHORT TO
GROUND
P2537-GLOW PLUG CONTROL CIRCUIT PREGLOW SHORT TO
VOLTAGE
The title for the tests will be P1482-GLOW PLUG MODULE -
COMMUNICATION ERROR.
POSSIBLE CAUSES
GLOW PLUG CONTROL SIGNAL CIRCUIT OPEN
GLOW PLUG CONTROL SIGNAL CIRCUIT SHORTED TO GROUND
GLOW PLUG CONTROL SIGNAL CIRCUIT SHORTED TO VOLTAGE
GLOW PLUG MODULE

displayed.
Yes → Go To 2
No → Go To 6

Disconnect the Glow Plug Module harness connectors.
Measure the resistance of the Glow Plug Control Signal circuit.
Measure the resistance of the Glow Plug Module Control circuit.
Yes → Go To 3
No → Repair the Glow Plug Control Signal circuit for an open.
80
P1482-GLOW PLUG MODULE - COMMUNICATION ERROR — Continued

Measure the resistance between ground and the Glow Plug Control Signal circuit.
Yes → Go To 4
No → Repair the Glow Plug Control Signal circuit for a short to ground.

connector.
Measure the voltage of the Glow Plug Control Signal circuit.
Yes → Go To 5
No → Repair the Glow Plug Control Signal circuit for a short to voltage.

Replace the Glow Plug Module in accordance with the Service Information.



81
Symptom List:
P1482-GLOW PLUG MODULE - EXCESS CURRENT
P2133-GLOW PLUG #1 CIRCUIT EXCESSIVE CURRENT
P2133-GLOW PLUG #1 CIRCUIT OPEN CIRCUIT
P2133-GLOW PLUG #1 CIRCUIT SHORT TO GROUND
P2133-GLOW PLUG #1 CIRCUIT SHORT TO VOLTAGE
EXCESS CURRENT.
POSSIBLE CAUSES
GLOW PLUG
GLOW PLUG CONTROL CIRCUIT OPEN
GLOW PLUG CONTROL CIRCUIT SHORTED TO GROUND
GLOW PLUG CONTROL CIRCUIT SHORTED TO VOLTAGE
GLOW PLUG MODULE
82
P1482-GLOW PLUG MODULE - EXCESS CURRENT — Continued

displayed.
Perform several ignition cycles leaving the ignition on for at least 10 seconds then off
for 10 seconds.
Yes → Go To 2
No → Go To 6

Disconnect each Glow Plug harness connector.
Disconnect the Glow Plug Module harness connector.
Measure the resistance of each Glow Plug Control circuit.
Is the resistance below 10.0 ohms for each circuit?
Yes → Go To 3
No → Repair the appropriate Glow Plug Control circuit for an open.

Measure the resistance between ground and each Glow Plug Control circuit.
Is the resistance below 1000.0 ohms for any of the measurements?
Yes → Repair the appropriate Glow Plug Control circuit for a short to
ground.
No → Go To 4

Measure the voltage of each Glow Plug Control circuit.
Is the voltage below 1.0 volt for each circuit?
Yes → Go To 5
No → Repair the appropriate Glow Plug Control circuit for a short to

voltage
83
P1482-GLOW PLUG MODULE - EXCESS CURRENT — Continued

Refer to the Service Information and perform the Glow Plug Test on each Glow plug.
Did each Glow Plug pass the test?
Yes → Replace the Glow Plug Module.

No → Replace the appropriate Glow Plug in accordance with the Service

Information.

84
Symptom List:
P1482-GLOW PLUG MODULE - INCORRECT TIMER
P1482-GLOW PLUG MODULE - INTERNAL FAULT
P2538-GLOW PLUG MODULE COMMUNICATION ERROR
P2538-GLOW PLUG MODULE EXCESSIVE CURRENT ERROR
P2538-GLOW PLUG MODULE TIMER ERROR
INCORRECT TIMER.
POSSIBLE CAUSES
GLOW PLUG MODULE

displayed.
NOTE: This DTC indicates an internal Glow Plug Control Module problem
or an incorrect Glow Plug Module has been installed.
Yes → Replace and program the Glow Plug Control Module in accor-
dance with the Service Information.
No → Go To 2
85
P1482-GLOW PLUG MODULE - INCORRECT TIMER — Continued


86
Symptom:
P1610-ENGINE CONTROL RELAY PLAUSIBILITY
P1610-ENGINE CONTROL RELAY PLAUSIBILITY

When Monitored: During after-run.
Set Condition: The internal ECM timer determines that the Engine Control Relay
remains on for more than 2.0 seconds after the ECM has turned off the Engine Control
Relay.
POSSIBLE CAUSES
CHECK FOR OTHER DTCS
CHECK THE ECM POWER AND GROUNDS
SUBSTITUTE ENGINE CONTROL RELAY

With the DRB, check for additional DTCs.
Are other DTCs present?
Yes → Refer to the Symptom List for diagnosis of the other DTCs before
continuing.
No → Go To 2
displayed.
Perform several ignition key cycles, pausing for at least 10 seconds between each
cycle.
Yes → Go To 3
No → Go To 5
87
P1610-ENGINE CONTROL RELAY PLAUSIBILITY — Continued

Install a substitute relay in place of the Engine Control Relay.
With the DRBIIIt, erase DTCs.
cycle.
Yes → Go To 4
No → Replace the Engine Control Relay.
4 Refer to symptom Checking the ECM Power and Grounds. All

Are the ECM Power and Ground circuits o.k.?
Yes → Replace the ECM in accordance with the Service Information.
No → Repair as necessary.


88
Symptom:
P1610-ENGINE CONTROL RELAY SHUTS OFF TOO EARLY
P1610-ENGINE CONTROL RELAY SHUTS OFF TOO EARLY

Set Condition: The internal ECM timer determines that the Engine Control Relay has
shut off before the AFTER-RUN mode of operation has been completed.
POSSIBLE CAUSES
ENGINE CONTROL RELAY CONTROL CIRCUIT OPEN INTERMITTENTLY

continuing.
No → Go To 2
displayed.
cycle.
Yes → Go To 3
No → Go To 5
89
P1610-ENGINE CONTROL RELAY SHUTS OFF TOO EARLY — Continued

cycle.
Yes → Go To 4

Measure the resistance of the Engine Control Relay Control circuit while wiggling
the wiring harness and connectors between the ECM and the Fuse Block #1.
Was the resistance above 10.0 ohms at any time while wiggling the wiring harness
and connectors?
Yes → Repair the Engine Control Relay Control circuit for an intermit-
tent open.


90
Symptom:
P1610-ENGINE CONTROL RELAY SHUTS OFF TOO LATE
P1610-ENGINE CONTROL RELAY SHUTS OFF TOO LATE

Set Condition: The internal ECM timer determines that the Engine Control Relay
remains on for more than 2.0 seconds after the ECM has turned off the Engine Control
Relay.
POSSIBLE CAUSES
ENGINE CONTROL RELAY CONTROL CIRCUIT SHORTED TO GROUND INTERMITTENTLY
ENGINE CONTROL RELAY OUTPUT CIRCUIT SHORTED TO VOLTAGE

continuing.
No → Go To 2
displayed.
cycle.
Yes → Go To 3
No → Go To 6
91
P1610-ENGINE CONTROL RELAY SHUTS OFF TOO LATE — Continued

cycle.
Yes → Go To 4

Measure the resistance between ground and the Engine Control Relay Control circuit
while wiggling the wiring harness and connectors.
Was the resistance below 1000.0 ohms at any time while wiggling the wiring harness
and connectors?
Yes → Repair the Engine Control Relay Control circuit for an intermit-
tent short to ground.
No → Go To 5

Measure the voltage of the Engine Control Relay Output circuit.
No → Repair the Engine Control Relay Output circuit for a short to

voltage.
92
P1610-ENGINE CONTROL RELAY SHUTS OFF TOO LATE — Continued


93
Symptom:
P1611-SENSOR SUPPLY 1 VOLTAGE IS TOO HIGH

Set Condition: The ECM detects a short to voltage on the APP Sensor 5-volt Supply
circuit or the CMP Sensor 5-volt Supply circuit.
POSSIBLE CAUSES
VISUAL WIRING AND CONNECTOR INSPECTION
SENSOR SUPPLY 1 SHORTED TO VOLTAGE

displayed.
Start the engine.
Yes → Go To 2
No → Go To 4

Visually inspect the wiring and connectors associated with the APP and CMP Sensors
for problems that may result in a short circuit.
Yes → Repair or replace wiring/connectors as necessary.

No → Go To 3
94
P1611-SENSOR SUPPLY 1 VOLTAGE IS TOO HIGH — Continued

Disconnect the APP and CMP Sensor harness connectors.
Measure the voltage at ECM harness connector cavities C1-38, C1-37, C2-13, C2-24
and C2-25.
Yes → Repair the circuit(s) that measured above 1.0 volt for a short to
voltage.


95
Symptom:
P1611-SENSOR SUPPLY 1 VOLTAGE IS TOO LOW

Set Condition: The ECM detects a short to ground on the APP Sensor 5-volt Supply
circuit or the CMP Sensor 5-volt Supply circuit.
POSSIBLE CAUSES
APP SENSOR
CMP SENSOR
SENSOR SUPPLY 1 SHORTED TO GROUND
ACCEL PEDAL POSITION SENSOR 5-VOLT SUPPY CIRCUIT SHORT TO SENSOR GROUND CIR-
CUIT
CAMSHAFT POSITION SENSOR 5-VOLT SUPPLY CIRCUIT SHORTED TO SENSOR GROUND
CIRCUIT

displayed.
Yes → Go To 2
No → Go To 8

Visually inspect the wiring and connectors associated with the APP and CMP Sensors
for problems that may result in a short circuit.

No → Go To 3
96
P1611-SENSOR SUPPLY 1 VOLTAGE IS TOO LOW — Continued

Disconnect the APP and CMP Sensor harness connectors.
Measure the resistance between ground and ECM harness connector cavities C1-38,
C1-37, C2-13, C2-24 and C2-25.
Is the voltage below 1000 ohms for any of the measurements?
Yes → Repair the circuit(s) that measured below 1000 ohms for a short to
ground.
No → Go To 4

Disconnect the Camshaft Position Sensor harness connector.
Measure the resistance between the Sensor Ground circuit and the CMP Sensor
5-volt Supply circuit at the CMP Sensor harness connector.
Yes → Go To 5
No → Repair the Camshaft Position Sensor 5-volt Supply circuit for a

short to the Sensor Ground circuit.

Measure the resistance between the 5-volt Supply circuit and each of the Sensor
Ground circuits at the APP Sensor harness connector.
Is the resistance above 1000 ohms for both measurements?
Yes → Go To 6
No → Repair the APP Sensor 5-volt Supply circuit for a short to the

Turn the ignition off for 10 seconds. Turn the ignition on.
With the DRBIIIt, read ECM DTCs.
Yes → Go To 7
No → Replace the APP Sensor.

97

Disconnect the CMP Sensor harness connector.

No → Replace the Camshaft Position Sensor.

98
Symptom:
P1612-IGNITION VOLTAGE - VOLTAGE ERROR
POSSIBLE CAUSES
CHECK THE ECM POWER AND GROUNDS

Yes → Go To 2
No → Go To 3
2 Refer to symptom Checking the ECM Power and Grounds. All

Are the ECM Power and Ground circuits o.k.?


99
Symptom List:
P1615-ECM VOLTAGE SUPPLY IS TOO HIGH
P1615-ECM VOLTAGE SUPPLY IS TOO LOW
The title for the tests will be P1615-ECM VOLTAGE SUPPLY
IS TOO HIGH.
P1615-ECM VOLTAGE SUPPLY IS TOO HIGH

Set Condition: The ECM detects voltage above 16 volts on the Battery Supply circuit(s).
P1615-ECM VOLTAGE SUPPLY IS TOO LOW

Set Condition: The ECM detects voltage below 8.0 volts on the ECM Battery Supply
circuit(s).
POSSIBLE CAUSES
ECM

displayed.
NOTE: This DTC may be caused by a charging system problem. Refer to the
Service Information and verify proper charging system operation before
continuing.
Yes → Go To 2
No → Go To 3
100
P1615-ECM VOLTAGE SUPPLY IS TOO HIGH — Continued

2 Refer to the symptom list and perform the Checking the ECM Power and Ground All
test.
Were any problem found with the ECM powers and grounds?




101
Symptom List:
P1630-IMMOBILIZER
P1630-IMMOBILIZER
P1630-IMMOBILIZER
P1630-IMMOBILIZER
P2201-IMMOBILIZER CAN MESSAGE ERROR
P2243-NO MESSAGE RECEIVED FROM SKREEM
The title for the tests will be P1630-IMMOBILIZER.
POSSIBLE CAUSES
CHECKING SKREEM DTC’S
OPEN CAN BUS CIRCUITS
SKREEM MODULE

displayed.
Yes → Go To 2
No → Go To 4

With the DRBIIIt, attempt to communicate with the SKREEM and read SKREEM
DTCs.
NOTE: If the DRB is unable to communicate with the SKREEM, refer to the
appropriate test in the Communication category
Are there any SKREEM DTC’s?
Yes → Repair SKREEM DTC’s as necessary.

No → Go To 3
102
P1630-IMMOBILIZER — Continued

Disconnect the SKREEM Module harness connector.
Measure the resistance of each CAN Bus circuit between the ECM harness connector
and the SKREEM harness connector.
Yes → Replace and program the SKREEM Module in accordance with
No → Repair the open CAN Bus circuit(s) between the ECM and the
SKREEM.

103
Symptom List:
P1681-ACM CIRCUIT FAULT
P1681-ACM CIRCUIT SHORT TO VOLTAGE
The title for the tests will be P1681-ACM CIRCUIT FAULT.
POSSIBLE CAUSES
AIRBAG CONTROL MODULE
ACM SIGNAL CIRCUIT SHORTED TO VOLTAGE

displayed.
With the DRB, check the Airbag Module for proper communication and DTCs. If
there are any ACM DTCs, repair them prior to continuing this test.
Start the engine.
Yes → Go To 2
No → Go To 4

connector.
Measure the voltage of the ACM Signal circuit.
Yes → Replace the Engine Control Module in accordance with the
No → Go To 3
104
P1681-ACM CIRCUIT FAULT — Continued

Refer to the Service Information and disconnect the ACM harness connector.
Remove the Engine Control Relay from the Fuse Block No.1
Measure the voltage of the ACM Signal circuit.
Yes → Replace and program the Airbag Control Module in accordance

No → Repair the ACM Signal circuit for a short to voltage.


105
Symptom List:
P2009-WATER IN FUEL SENSOR - WATER IN FUEL
P2009-WATER IN FUEL SENSOR SIGNAL ERROR
The title for the tests will be P2009-WATER IN FUEL SENSOR
- WATER IN FUEL.
POSSIBLE CAUSES
12-VOLT SUPPLY CIRCUIT OPEN
ECM - WATER IN FUEL SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE
ECM - WATER IN FUEL SENSOR SIGNAL SHORT TO GROUND
WATER IN FUEL SENSOR FAILURE
WATER IN FUEL SENSOR SIGNAL CIRCUIT OPEN
WATER IN FUEL SENSOR SIGNAL CIRCUIT SHORTED TO 12-VOLT SUPPLY
WATER IN FUEL SENSOR SIGNAL CIRCUIT SHORTED TO GROUND
WATER IN FUEL SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND
WATER IN FUEL SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE

displayed.
NOTE: If you are here due to a P2009 indicating (Water In The Fuel Filter(
DTC, ensure that the fuel system is not contaminated with water or other
fluids before continuing.
NOTE: If the fuel system is contaminated, refer to the Service Information
to remove fuel, clean system and refill with known good fuel.
Start the engine several times, letting the engine run for at least 30 seconds at a
time.
Yes → Go To 2
No → Go To 11
106
P2009-WATER IN FUEL SENSOR - WATER IN FUEL — Continued


Go To 3

Disconnect the Water In Fuel Sensor harness connector.
Measure the voltage of the Water In Fuel Sensor Signal circuit.
Go To 4
Go To 6
Go To 8

Disconnect the In Fuel Level Sensor harness connector.
connector.
Measure the voltage of the Water In Fuel Sensor Signal circuit.
Yes → Go To 5
No → Repair the Water In Fuel Sensor Signal circuit for a short to
voltage.
107

Measure the resistance between the 12-volt supply circuit and the Water In Fuel
Sensor Signal circuit.
No → Repair the Water In Fuel Sensor Signal circuit for a short to the
12-volt Supply circuit.

Measure the resistance of the 12-Volt Supply circuit between the ECM harness
connector and the Water In Fuel Sensor harness connector.
Yes → Go To 7
No → Repair the 12-Volt Supply circuit for an open.

Yes → Replace the Water In Fuel Sensor.

Measure the resistance of the Water In Fuel Sensor Signal circuit.
Yes → Go To 9
No → Repair the Water In Fuel Sensor Signal circuit for an open.

Measure the resistance between ground and the Water In Fuel Sensor Signal circuit.
Yes → Go To 10
No → Repair the Water In Fuel Sensor Signal circuit for a short to
ground.
108

Measure the resistance between Sensor Ground and the Water In Fuel Sensor Signal
circuit.
No → Repair the Water In Fuel Sensor Signal circuit for a short to the

109
Symptom List:
P2010-MASS AIR FLOW SENSOR NEGATIVE DEVIATION
P2010-MASS AIR FLOW SENSOR POSITIVE DEVIATION
TOO LARGE
TOO SMALL
NEGATIVE DEVIATION.
P2010-MASS AIR FLOW SENSOR NEGATIVE DEVIATION

P2010-MASS AIR FLOW SENSOR POSITIVE DEVIATION

P2068-MASS AIR FLOW SENSOR PLAUSIBILITY SIGNAL RATIO TOO LARGE

P2068-MASS AIR FLOW SENSOR PLAUSIBILITY SIGNAL RATIO TOO SMALL

POSSIBLE CAUSES
MASS AIRFLOW SENSOR
110
P2010-MASS AIR FLOW SENSOR NEGATIVE DEVIATION — Continued

1 NOTE: Inspect the turbocharger inlet tube between the MAF Sensor and the All
turbocharger for damage, restriction or poor connection. Any of these
conditions can cause a MAF Plausibility DTC.
displayed.
Yes → Replace the MAF Sensor.
No → Go To 2


111
Symptom List:
P2013-AMBIENT AIR TEMPERATURE SIGNAL VOLTAGE TOO
HIGH
P2013-AMBIENT AIR TEMPERATURE SIGNAL VOLTAGE TOO LOW
The title for the tests will be P2013-AMBIENT AIR TEMPER-
ATURE SIGNAL VOLTAGE TOO HIGH.
P2013-AMBIENT AIR TEMPERATURE SIGNAL VOLTAGE TOO HIGH

Set Condition: The Ambient Air Temperature Sensor signal is above 4.82 volts.
P2013-AMBIENT AIR TEMPERATURE SIGNAL VOLTAGE TOO LOW

Set Condition: The Ambient Air Temperature Sensor signal is below 0.068 volt.
1 NOTE: The Ambient Air Temperature Sensor is hardwired to the Instrument All
Cluster
NOTE: Refer to the Instrument Cluster Diagnostic Information for the
related symptom(s).
Test Complete.
112
Symptom List:
P2014-ENGINE OIL SENSOR OIL TEMPERATURE PLAUSIBILITY
P2014-ENGINE OIL SENSOR SIGNAL PLAUSIBILITY
P2014-ENGINE OIL SENSOR SIGNAL VOLTAGE IS TOO HIGH
P2014-ENGINE OIL SENSOR SIGNAL VOLTAGE IS TOO LOW
P2040-ENGINE OIL SENSOR CIRCUIT INVALID LEVEL
P2040-ENGINE OIL SENSOR CIRCUIT LEVEL OUT OF RANGE
P2040-ENGINE OIL SENSOR CIRCUIT LEVEL OUT OF RANGE
P2041-ENGINE OIL SENSOR POOR OIL QUALITY
P2041-ENGINE OIL SENSOR QUALITY MEASUREMENT ERROR
P2041-ENGINE OIL SENSOR QUALITY PLAUSIBILITY
P2042-ENGINE OIL SENSOR WATER CONTAMINATION
P2061-ENGINE OIL SENSOR OPEN CIRCUIT
P2062-ENGINE OIL SENSOR SIGNAL ERROR
P2062-ENGINE OIL SENSOR SYNCHRONIZATION ERROR
The title for the tests will be P2014-ENGINE OIL SENSOR OIL
TEMPERATURE PLAUSIBILITY.
POSSIBLE CAUSES
ECM - ENGINE OIL SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE
ECM - ENGINE OIL SENSOR SIGNAL SHORT TO GROUND
ENGINE OIL SENSOR FAILURE
ENGINE OIL SENSOR SIGNAL CIRCUIT OPEN
ENGINE OIL SENSOR SIGNAL CIRCUIT SHORTED TO GROUND
ENGINE OIL SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND
ENGINE OIL SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE
ENGINE OIL CONTAMINATION
113
P2014-ENGINE OIL SENSOR OIL TEMPERATURE PLAUSIBILITY —

Continued
displayed.
NOTE: The engine oil must be at the proper level for this test to be valid.
Refer to the Service Information and ensure the engine oil level is at the
specified level.
Start the engine several times, letting the engine run for at least 30 seconds at a
time.
Yes → Go To 2
No → Go To 10

NOTE: This DTC implies that the engine may be contaminated by water,
engine coolant or other material due to a mechanical or service failures
such as failed gaskets, seals, cracks or incorrectly installed components.
Inspect the engine for conditions referred to in the above note.
No → Go To 3

Disconnect the Engine Oil Sensor harness connector.
Measure the voltage of the Engine Oil Sensor Signal circuit.

Go To 4

Go To 5

Go To 7
114

Continued
connector.
Measure the voltage of the Engine Oil Sensor Signal circuit.

No → Repair the Engine Oil Sensor Signal circuit for a short to voltage.

connector and the Engine Oil Sensor harness connector.
Yes → Go To 6


Measure the resistance of the Engine Oil Sensor Signal circuit.
Yes → Go To 8
No → Repair the Engine Oil Sensor Signal circuit for an open.


Measure the resistance between ground and the Engine Oil Sensor Signal circuit.
Yes → Go To 9
No → Repair the Engine Oil Sensor Signal circuit for a short to ground.
115

Continued
Measure the resistance between Sensor Ground and the Engine Oil Sensor Signal
circuit.
No → Repair the Engine Oil Sensor Signal circuit for a short to the

116
Symptom List:
P2015-FUEL RAIL PRESSURE MALFUNCTION MAXIMUM FUEL
FLOW EXCEEDED
P2016-FUEL RAIL PRESSURE MALFUNCTION DECELERATION
ERROR
P2016-FUEL RAIL PRESSURE MALFUNCTION FUEL FLOW BE-
LOW MINIMUM QUANTITY
P2017-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE IS
TOO LOW
TOO HIGH
PRESSURE EXCEEDED
TOO LOW
TOO LOW
P2020-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE
TOO HIGH
TOO LOW
TOO HIGH
PRESSURE EXCEEDED
P2049-FUEL RAIL PRESSURE MALFUNCTION DECELERATION
ERROR
PRESSURE EXCEEDED
P2052-FUEL RAIL PRESSURE MALFUNCTION PLAUSIBILITY
WITH FUEL PRESSURE SOLENOID
The title for the tests will be P2015-FUEL RAIL PRESSURE
MALFUNCTION MAXIMUM FUEL FLOW EXCEEDED.
POSSIBLE CAUSES
AIR IN FUEL SYSTEM
CHECKING ELECTRICAL CIRCUITS-ENGINE RUNNING
CHECKING ELECTRICAL CIRCUITS-NO START
CHECKING FOR OTHER DTC’S
CHECKING THE FUEL DELIVERY SYSTEM
117

EXCEEDED — Continued
POSSIBLE CAUSES
CHECKING THE FUEL DELIVERY SYSTEM
CORRECTION QUANTITY CHECK
CYLINDER SPEED CHECK
FUEL INJECTION PUMP CHECK
FUEL LEAK QUANTITY CHECK
FUEL LEAK QUANTITY CHECK
FUEL PRESSURE SOLENOID
FUEL PRESSURE SOLENOID CHECK
FUEL PRESSURE VARIATION CHECK
FUEL PUMP
FUEL QUANTITY SOLENOID
FUEL SYSTEM CONTAMINATION
FUEL SYSTEM LEAK

1 WARNING: HIGH-PRESSURE FUEL LINES DELIVER DIESEL FUEL UN- All
DER EXTREME PRESSURE FROM THE INJECTION PUMP TO THE FUEL
INJECTORS. THIS MAY BE AS HIGH AS 23,200 PSI (1600 BAR). USE
EXTREME CAUTION WHEN INSPECTING FOR HIGH-PRESSURE FUEL
LEAKS.
WARNING: FUEL UNDER THIS AMOUNT OF PRESSURE CAN PENE-
TRATE SKIN CAUSING PERSONAL INJURY OR DEATH. INSPECT FOR
HIGH-PRESSURE FUEL LEAKS WITH A SHEET OF CARDBOARD. WEAR
SAFETY GOGGLES AND ADEQUATE PROTECTIVE CLOTHING WHEN
SERVICING FUEL SYSTEM.
Are there any other DTCs present?
Yes → Refer to symptom list for problems related to the DTC other than
this DTC.
No → Go To 2

Attempt to start the engine.
Does the engine start and idle?
Yes → Go To 3
No → Go To 17
118

WARNING: HIGH-PRESSURE FUEL LINES DELIVER DIESEL FUEL UN-
LEAKS.
Inspect the entire fuel system for leakage.
Is there any evidence of leakage?
Yes → Repair as necessary in accordance with the Service Information.
No → Go To 4
4 NOTE: Mixing any other fuels such as gasoline or kerosine can cause this All
DTC to set.
LEAKS.
Refer to the Service Information and inspect the fuel system for contamination.
Is the fuel contaminated?

No → Go To 5
119

these conditions are displayed on the DRB IIIt at the same time the DTC is
displayed.
NOTE: Refer to the Service Information and perform the Air Bleed Proce-
dure before continuing diagnosis.
Start and idle the engine while monitoring for ECM DTC’s.
If the DTC does not reset at idle condition, test drive the vehicle under various load
and speed conditions to attempt to duplicate the fault.
NOTE: Driving the vehicle up and down steep hills or rapid cornering with
a low fuel level can cause this DTC to set. Verify with customer if Low Fuel
Light was illuminated when fault occurred.
Yes → Go To 6
No → Go To 16
6 Start the engine. All

With the DRBIIIt in Sensors, compare the Fuel Pressure Setpoint with the Actual
Fuel Pressure readings.
NOTE: If there is air in the fuel system, the Actual Fuel Pressure will
oscillate above and below the Fuel Pressure Setpoint.
Does Actual Fuel Pressure oscillate above and below the Fuel Pressure Setpoint?
Yes → Refer to the Service Information to purge air from the fuel system.
No → Go To 7
7 Start the engine. All

With the DRBIIIt in Sensors, compare the Fuel Pressure Setpoint with the Actual
Fuel Pressure readings.
NOTE: A sticking Fuel Pressure Solenoid is indicated by Actual Fuel
Pressure gradually dropping below the Fuel Pressure Setpoint then sud-
denly increasing (spiking) above the Fuel Pressure Setpoint.
Does Actual Fuel Pressure gradually decrease then suddenly increase (spike) above
the Fuel Pressure
Yes → Replace the Fuel Pressure Solenoid in accordance with the

No → Go To 8
120

8 Refer to the appropriate Service Information and refer to Diagnosis and Testing Fuel All
Delivery System table.
NOTE: The following is a list of problems that can cause fuel pressure to
deviate from specification: restricted fuel filter or fuel lines, failed fuel
pressure solenoid, failed fuel lift pump, failed fuel sending unit, contami-
nated fuel, faulty injector.
Were there any problems with the Fuel Delivery System?

No → Go To 9
9 Refer to each of the following symptoms in the Driveability category. All

CHECKING THE FUEL PRESSURE SOLENOID CIRCUITS
CHECKING THE FUEL QUANTITY SOLENOID CIRCUITS
CHECKING THE FUEL PRESSURE SENSOR CIRCUITS
No → Go To 10
10 NOTE: An injector that sticks open can cause this DTC. A sticking injector All
will cause the engine to misfire and emit excessive black smoke from the
exhaust system.
Refer to the Service Information and perform the Fuel Injector Leak Quantity Test.
Yes → Using the Service Information, remove and inspect the Fuel
Injectors for signs of damage or debris that may cause the injector
to stick. Sticking injectors may cause the combustion chamber to
become black and oil soaked. Replace Injector(s) as necessary.
No → Go To 11
11 With the DRBIIIt, select System Test, Smooth Eng Run Check, then Correction All
Quantity Check.
Perform this test at Idle, 2000 rpm and 3000 rpm.
NOTE: Readings per cylinder should be below ± 0.00450 mm3/stroke for each
cylinder at each engine speed.
Did any of the cylinders exceed ± 0.00450 mm3/stroke during this test?
Yes → Replace Fuel Injector of the cylinder(s) that had readings above ±
0.00450 mm3/stroke.
No → Go To 12
12 With the DRBIIIt, select System Test, Smooth Eng Run Check, then Cylinder Speed All
Check.
NOTE: Readings for all cylinders should be close to each other. Look for one
or two cylinders to differ high or low from the other cylinders.
Did any of the cylinders differ significantly from the majority of the other cylinders?
Yes → Replace Fuel Injector of the cylinder(s) that had readings signif-
icantly above or below the other fuel injectors.
No → Go To 13
121

13 With the DRBIIIt, select System Tests, then perform the Rail Press Control Valve All
Test.
Did this test pass?
Yes → Go To 14
No → Replace the Fuel Pressure Solenoid in accordance with the

14 With the DRBIIIt, select System Tests, then perform the Rail Press Control Valve All
Variation Test.
Did this test pass?
Yes → Go To 15
No → Replace the Fuel Pressure Solenoid in accordance with the

15 With the DRBIIIt, select System Test, then High Pressure Pump. All
NOTE: During this test engine speed is set at 1,400 rpm and initial fuel
pressure at approximately 6,800 psi. During the test fuel pressure is
instantly set to above 20,000 psi. to test the performance of the Fuel
Injection Pump.
NOTE: After the test is completed, the DRB display fuel pressure in 30
counter steps. If the fuel pressure increases from approximately 6,800 psi to
above 20,000 psi in one counter step, the injection pump passes the test.
Did the fuel pressure increase to above 20,000 psi within one counter step on the
DRB?
Yes → Replace the Fuel Quantity Solenoid in accordance with the
No → Replace Fuel Injection Pump in accordance with the Service

Information.

With the engine running and at normal operating temperature, monitor the DRB IIIt
122

17 Refer to the appropriate Service Information and refer to Diagnosis and Testing Fuel All
Delivery System table.
NOTE: The following is a list of problems that can cause fuel pressure to
deviate from specification: restricted fuel filter or fuel lines, failed fuel
pressure solenoid, air in fuel system, failed fuel sending unit, contaminated
fuel, faulty injector.
Were there any problems with the Fuel Delivery System?

No → Go To 18
18 Refer to each of the following symptoms in the Driveability category. All

CHECKING THE FUEL PRESSURE SOLENOID CIRCUITS
CHECKING THE FUEL QUANTITY SOLENOID CIRCUITS
CHECKING THE FUEL PRESSURE SENSOR CIRCUITS
No → Go To 19
19 NOTE: An injector that sticks open can cause this DTC. A sticking injector All
will cause the engine to misfire and emit excessive black smoke from the
exhaust system.
Refer to the Service Information and perform the Fuel Injector Leak Quantity during
engine cranking test.
Yes → Using the Service Information, remove and inspect the Fuel
Injectors for signs of damage or debris that may cause the injector
to stick. Sticking injectors may cause the combustion chamber to
become black and oil soaked. Replace Injector(s) as necessary.
No → Go To 20

Replace the Fuel Pressure Solenoid in accordance with the Service Information.
Attempt to start and test drive the vehicle.
Yes → Go To 21
123

Replace the Fuel Quantity Solenoid in accordance with the Service Information.
Attempt to start and test drive the vehicle.
Yes → Replace the Fuel Pump in accordance with the Service Informa-
tion.
124
Symptom:

Set Condition: The Intake Pressure Sensor signal does not agree with the Atmospheric
Pressure Sensor signal in the ECM.
POSSIBLE CAUSES
AIR FILTER
AIR RESTRICTION
HIGH RESISTANCE IN THE INTAKE PRESSURE SENSOR SIGNAL CIRCUIT
HIGH RESISTANCE IN THE INTAKE PRESSURE SENSOR GROUND CIRCUIT
HIGH RESISTANCE IN THE INTAKE PRESSURE SENSOR 5-VOLT SUPPLY CIRCUIT

displayed.
Turn the ignition off, wait 30 seconds.
Yes → Go To 2
No → Go To 7


No → Go To 3
125
P2025-INTAKE PRESSURE SENSOR PLAUSIBILITY — Continued

to set.
were any problems found?
No → Go To 4

Yes → Go To 5
No → Repair the Intake Pressure Sensor Signal circuit for high resis-
tance.

Yes → Go To 6
No → Repair the Intake Pressure Sensor Ground circuit for high resis-
tance.

Measure the resistance of the Intake Pressure Sensor 5-volt Supply circuit.
No → Repair the Intake Pressure Sensor 5 Volt Supply circuit for high
resistance.
126
P2025-INTAKE PRESSURE SENSOR PLAUSIBILITY — Continued


127
Symptom List:
P2030-INTAKE PRESSURE SENSOR CIRCUIT FAULT
P2030-INTAKE PRESSURE SENSOR OPEN CIRCUIT
SENSOR SIGNAL VOLTAGE TOO HIGH.
POSSIBLE CAUSES
INTAKE PRESSURE SENSOR GROUND CIRCUIT SHORTED TO VOLTAGE
INTAKE PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE
INTAKE PRESSURE SENSOR GROUND CIRCUIT OPEN
ENGINE CONTROL MODULE (INTERNAL)
ENGINE CONTROL MODULE (SENSOR SIGNAL SHORTED TO VOLTAGE)

displayed.
ensure the Boost Pressure Servo Motor and Servo Motor rod are attached
and functioning properly.
seconds at a time.
Yes → Go To 2
No → Go To 7
128

Continued
Yes → Go To 3
No → Go To 4

connector.
Yes → Repair the Intake Pressure Sensor Signal circuit for a short to
voltage.

connector.
Measure the voltage between ground and the Intake Pressure Sensor Ground circuit.
Yes → Repair the Intake Pressure Sensor Ground circuit for a short to
voltage. Note: The ECM will need to be checked for proper
operation before the repair is completed. A short to voltage on a
ground circuit can damage the ECM.
No → Go To 5

Yes → Go To 6
No → Repair the Intake Pressure Sensor Ground circuit for an open.

129

Continued
NOTE: Ensure all harness connectors are connected.
Measure the voltage of the Intake Pressure Sensor Signal circuit by back probing
ECM harness connector.


130
Symptom List:
SENSOR SIGNAL VOLTAGE TOO LOW.
POSSIBLE CAUSES
INTAKE PRESSURE SENSOR 5 VOLT SUPPLY
INTAKE PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO GROUND
INTAKE PRESSURE SENSOR SIGNAL AND GROUND CIRCUITS SHORTED TOGETHER
INTAKE PRESSURE SENSOR SIGNAL CIRCUIT OPEN

displayed.
seconds at a time.
Yes → Go To 2
No → Go To 7

Measure the voltage between ground and the Intake Pressure Sensor 5 Volt Supply
circuit.
Yes → Go To 3
No → Repair the Intake Pressure Sensor 5 Volt Supply circuit for an

open.
131

Continued
Yes → Go To 4
No → Repair the Intake Pressure Sensor Signal circuit for an open.


Measure the resistance between the Intake Pressure Sensor Signal circuit and
Yes → Go To 5
No → Repair the Intake Pressure Sensor Signal circuit for a short to the

Measure the resistance between ground and the Intake Pressure Sensor Signal
circuit.
Yes → Go To 6
No → Repair the Intake Pressure Sensor Signal circuit for a short to
ground.

Connect a jumper wire between the Intake Pressure Sensor Signal and Intake
Pressure Sensor 5 Volt Supply circuits.


132

Continued

133
Symptom List:
P2026-O2 SENSOR CIRCUIT FAULT
P2026-O2 SENSOR CIRCUIT OPEN CIRCUIT
P2026-O2 SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH
P2026-O2 SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW
P2028-O2 SENSOR CIRCUIT FAULT
P2028-O2 SENSOR CIRCUIT OPEN CIRCUIT
P2028-O2 SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH
P2028-O2 SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW
P2032-O2 SENSOR PLAUSIBILITY
P2057-O2 SENSOR SIGNAL CIRCUIT SIGNAL VOLTAGE TOO HIGH
P2090-O2 SENSOR SIGNAL FAULT
P2091-O2 SENSOR LOW O2 CONCENTRATION
P2091-O2 SENSOR SIGNAL PLAUSIBILITY
P2195-O2 SENSOR HEATER CIRCUIT FAULT
P2366-O2 CIRCUIT FAULT
The title for the tests will be P2026-O2 SENSOR CIRCUIT
FAULT.
POSSIBLE CAUSES
CHECKING CIRCUIT INTEGRITY
ECM
O2 SENSOR
O2 SENSOR CIRCUIT SHORT TO GROUND
O2 SENSOR CIRCUIT SHORT TO VOLTAGE
O2 SENSOR CIRCUIT SHORT TOGETHER
O2 SENSOR OPEN CIRCUIT
POWER SUPPLY OPEN
134
P2026-O2 SENSOR CIRCUIT FAULT — Continued

displayed.
Yes → Go To 2
No → Go To 9

Using the Service Information wiring diagrams, inspect the wiring and connectors
between the ECM and the O2 sensor for damage, corrosion, poor terminal contact or
other problems.
Yes → Clean, repair or replace as necessary.
No → Go To 3

Disconnect the O2 Sensor harness connector.
Using a 12-volt test light connected to ground, check the Power Supply circuit at the
O2 harness connector cavity 4.
Yes → Go To 4
No → Repair the Power Supply circuit for an open or short to ground.


Perform the following resistance measurements from the O2 harness connector to the
O2 Sensor Cavity 1 to ECM Cavity C1-15.
Yes → Go To 5
No → Repair the circuit(s) that measured above 10.0 ohms for an open.
135

Measure the resistance between ground and O2 Sensor harness connector cavities 1,
2, 3, 5, and 6.
Is the resistance above 1000 ohms for each measurement?
Yes → Go To 6
No → Repair the circuit(s) that measured below 1000 ohms for a short to
ground.

NOTE: The circuits connecting the O2 Sensor and the ECM are single
circuits and do not contain any splices. There should be NO continuity from
one circuit to the other.
Using an ohmmeter, check the O2 Sensor circuits for shorts together (resistance
below 1000 ohms)..
Is the resistance from any O2 Sensor circuit to another below 1000 ohms?
Yes → Repair the circuits that measured below 1000 ohms for a short
together.
No → Go To 7

connector.
Measure the voltage of O2 Sensor harness connector cavities 1, 2, 3, 5, and 6.
Is the voltage below 1.0 volts for each measurement?
Yes → Go To 8
voltage.

Replace the O2 Sensor in accordance with the Service Information.

136


137
Symptom List:
P2034-O2 SENSOR CIRCUIT CALIBRATION VALUE TOO HIGH
P2034-O2 SENSOR CIRCUIT CALIBRATION VALUE TOO LOW
The title for the tests will be P2034-O2 SENSOR CIRCUIT
CALIBRATION VALUE TOO HIGH.
POSSIBLE CAUSES
CHECKING CIRCUIT INTEGRITY
O2 SENSOR

Using the Service Information wiring diagrams, inspect the wiring and connectors
between the ECM and the O2 sensor for damage, corrosion, poor terminal contact or
other problems.
Yes → Clean, repair or replace as necessary.
No → Go To 2
displayed.
Yes → Replace the Oxygen Sensor.

No → Go To 3
138
P2034-O2 SENSOR CIRCUIT CALIBRATION VALUE TOO HIGH —

Continued

139
Symptom List:
P2043-CAMSHAFT POSITION SENSOR CIRCUIT OPEN CIRCUIT
P2043-CAMSHAFT POSITION SENSOR CIRCUIT OPEN OR SHORT
CIRCUIT
The title for the tests will be P2043-CAMSHAFT POSITION
SENSOR CIRCUIT OPEN CIRCUIT.
POSSIBLE CAUSES
CAMSHAFT POSITION SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE
CHECKING 5-VOLT SUPPLY CIRCUIT
DAMAGED CMP SENSOR OR CAMSHAFT
ECM
ECM
ECM - CAMSHAFT POSITION SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE
CMP SENSOR SIGNAL CIRCUIT OPEN
5-VOLT SUPPLY CIRCUIT SHORTED TO GROUND
CMP SENSOR SIGNAL CIRCUIT SHORTED TO GROUND
CMASHAFT POSITION SENSOR
ECM SENSOR GROUND CIRCUIT OPEN
5-VOLT SUPPLY CIRCUIT SHORTED TO THE SENSOR GROUND CIRCUIT
CMP SENSOR SIGNAL CIRCUIT SHORTED TO THE SENSOR GROUND CIRCUIT
140
P2043-CAMSHAFT POSITION SENSOR CIRCUIT OPEN CIRCUIT —

Continued
NOTE: The Timing Belt/Chain must be correctly installed and operational
before diagnosis can be made. Refer to the Service Information to ensure
the timing belt is properly installed.
displayed.
Attempt to start the engine cranking the engine for at least 7 seconds.
Yes → Go To 4
No → Go To 2

Yes → Go To 3
No → Go To 16

Measure the voltage of the CMP Sensor Signal circuit.
Go To 4
Go To 5
Go To 13
141

Continued
connector.
Measure the voltage of the CMP Position Sensor Signal circuit.

No → Repair the Camshaft Position Sensor Signal circuit for a short to

voltage.

Measure the voltage of the CMP Sensor 5-Volt Supply circuit.

Repair the CMP 5-Volt Supply circuit for a short to voltage.
Go To 6
Go To 10

Measure the resistance of the Sensor Ground circuit between the CMP Sensor
harness connector and the ECM harness connector.
Yes → Go To 7

Connect one end of a jumper wire to the ECT Sensor signal circuit in the ECT Sensor
harness connector.
Connect the other end of the jumper wire to the Sensor Ground circuit in the
Camshaft Position Sensor harness connector.
With the DRBIIIt in Engine, Sensors, read the Engine Coolant Temp volts.
Yes → Go To 8

Information.
142

Continued
Remove the CMP Sensor.
Inspect the CMP Sensor for conditions such as loose mounting screws, damage, or
cracks.
Inspect the camshaft for conditions such as damage, debris or cracked teeth.
Is there any evidence of these conditions?
No → Go To 9

With the DRBIIIt lab scope lead, backprobe the CMP Signal circuit.
Set the DRBIIIt lab scope settings as follows: Time = 0.2s/Div, 20 volts scale, Offset
= 0.00 volts, Probe = X10, Coupling = DC.
While observing the DRBIIIt display, crank the engine.
NOTE: The DRBIIIt should display a digital signal (square wave) similar to
that shown in Charts and Graphs.
Does the DRBIIIt display an uninterrupted digital signal (square wave)?

No → Replace the Camshaft Position Sensor in accordance with the

connector and the CMP Sensor harness connector.
Yes → Go To 11

Measure the resistance between ground and the CMP Sensor 5-Volt Supply circuit.
Yes → Go To 12
No → Repair the CMP Sensor 5-Volt Supply circuit for a short to ground.
143

Continued
Measure the resistance between the CMP Sensor 5-Volt Supply circuit and the
Sensor Ground circuit at the CMP Sensor harness connector.
No → Repair the CMP Sensor 5-Volt Supply and Sensor Ground circuits
for a short together.

Measure the resistance of the CMP Sensor Signal circuit.
Yes → Go To 14
No → Repair the CMP Sensor Signal circuit for an open

Measure the resistance between ground and the CMP Sensor Signal circuit.
Yes → Repair the CMP Sensor Signal circuit for a short to ground.
No → Go To 15

Measure the resistance between the CMP Sensor Signal circuit and the Sensor
Ground circuit at the CMP Sensor harness connector.
Yes → Repair the CMP Sensor Signal and Sensor Ground circuits for a
short together.

144

Continued
Remove the CMP Sensor and the CKP Sensor, checking for loose mounting screws
and debris on the sensor magnets that can corrupt the sensor signal.

145
Symptom List:
P2045-CRANKSHAFT POSITION SENSOR CIRCUIT LOST SIGNAL
P2045-CRANKSHAFT POSITION SENSOR CIRCUIT SIGNAL PLAU-
SIBILITY
P2322-CRANKSHAFT POSITION SENSOR PLAUSIBILITY
P2343-CKP PLAUSIBILITY
The title for the tests will be P2045-CRANKSHAFT POSITION
SENSOR CIRCUIT LOST SIGNAL.
POSSIBLE CAUSES
CKP MOUNTING AND FLYWHEEL
CRANKSHAFT POSITION SENSOR
OPEN SHIELD CIRCUIT
CRANKSHAFT POSITION SENSOR SIGNAL CIRCUIT(S) SHORTED TO GROUND
CKP SENSOR CIRCUITS SHORTED TOGETHER
CKP SENSOR SIGNAL CIRCUITS OPEN
CKP SENSOR SIGNAL CIRCUIT(S) SHORTED TO VOLTAGE

displayed.
Did the engine start?
Yes → Go To 2
No → Go To 3
146
P2045-CRANKSHAFT POSITION SENSOR CIRCUIT LOST SIGNAL —

Continued

3 Refer to the Service Information to ensure the Engine Drive Gears/Sprocket are All
installed correctly and the camshaft and crankshaft gears are timed correctly.
Disconnect the CKP Sensor harness connector.
Measure the resistance between ground and both of the CKP Sensor Signal circuits.
Yes → Go To 4
No → Repair the CKP Sensor Signal circuit(s) for a short to ground.

Measure the resistance between the CKP Sensor Signal circuits.
Yes → Go To 5
No → Repair the CKP Sensor Signal circuits for a short together.

Measure the resistance of CKP Sensor Signal circuits.
Is the resistance below 10.0 ohms for both measurements?
Yes → Go To 6
No → Repair the CKP Sensor Signal circuit(s) for an open.
147
P2045-CRANKSHAFT POSITION SENSOR CIRCUIT LOST SIGNAL —

Continued
connector.
Measure the voltage of both CKP Sensor Signal circuits.
Is the voltage below 1.0 volt for both measurements?
Yes → Go To 7
No → Repair the CKP Sensor Signal circuit(s) for a short to voltage.

Using the DRB lab scope, backprobe both of the CKP Sensor Signal circuits at the
NOTE: Refer to Charts and Graphs to view a correct CKP Sensor signal.
Start the engine, if the engine will not start, crank the engine for several seconds
while monitoring the DRB.
Does the DRB display a steady clean CKP Signal pattern for both circuits?
Yes → Go To 8
No → Replace the Crankshaft Position Sensor.

Inspect the CKP Sensor Shield circuit.
Yes → Repair the Shield circuit as necessary.

No → Go To 9

Inspect the CKP Sensor for signs of damage or improper/loose attachment to the
engine.
Inspect the flywheel for excessive dirt contamination or tooth damage which can
cause improper CKP Sensor signal output.
Where any of these problems found?
148
Symptom:
P2062-ENGINE OIL SENSOR MONITORING ERROR
POSSIBLE CAUSES
ENGINE OIL SENSOR
VERIFY THE CURRENT DTC

Check the engine oil level. Add or remove as necessary to obtain proper engine oil
level.
Start the engine and allow it to reach operating temperature.

No → Test complete.
149
Symptom List:
P2066-MASS AIR FLOW SENSOR PLAUSIBILITY
P2355-EGR FLOW RATE IS TOO HIGH
P2355-EGR FLOW RATE IS TOO LOW
PLAUSIBILITY.
P2066-MASS AIR FLOW SENSOR PLAUSIBILITY

Set Condition: The ECM detects a rationality problem with the MAF Sensor or excessive
EGR flow.
POSSIBLE CAUSES
AIR FILTER
AIR RESTRICTION
CHECKING FOR AIR LEAKS
EGR ACTUATION - 1200 RPM
EGR VALVE
MAF SENSOR
MAF SENSOR READING - 3OOO RPM
EGR RESTRICTION

displayed.
Test drive the vehicle and monitor the DRB for ECM DTCs.
Yes → Go To 2
No → Go To 10
150
P2066-MASS AIR FLOW SENSOR PLAUSIBILITY — Continued

2 Start and idle the engine. All
With the DRBIIIt in Sensors, read the MAF mg/strk and compare it to the MAF
SPEC mg/strk with the engine at idle.
NOTE: The MAF Sensor reading should be within 5% of the MAF Spec
reading.
Is the MAF Sensor reading within 5% of the MAF Spec?
Yes → Go To 3
No → Go To 7
3 Place the transmission in Park or Neutral for this test. All

Start the engine and increase engine the engine speed to 3000 RPM.
With the DRBIIIt in Sensors, read the MAF mg/strk and compare it to the MAF
SPEC mg/strk with the engine speed at 3000 RPM.
NOTE: The MAF Sensor reading should be within 5% of the MAF Spec
reading.
Is the MAF Sensor reading within 5% of the MAF Spec?
Yes → Go To 4
No → Go To 7
4 NOTE: Inspect the complete exhaust system for restriction. Restrictions in All
the exhaust system can cause improper EGR flow. Repair as necessary
Allow the engine to idle until the engine reaches operating temperature.
With the DRBIIIt, actuate the EGR Positioner with the engine idling.
NOTE: The EGR Positioner will actuate from 5% to 95%. With the engine
idling at approximately 680 RPM the MAF reading should switch a mini-
mum of 200 mg/strk between 5% and 95% of EGR actuation.
Note the MAF readings.
Does the MAF switch a minimum of 200 mg/strk between 5% and 95% of EGR
actuation?
Yes → Go To 5
No → Go To 6
5 Allow the engine to idle until the engine reaches operating temperature. All
With the DRBIIIt, actuate the EGR Positioner with the engine speed at 1200 RPM.
NOTE: The EGR Positioner will actuate from 5% to 95%. With the engine
speed at approximately 1200 RPM the MAF reading should switch a mini-
mum of 200 mg/strk between 5% and 95% of EGR actuation.
Note the MAF readings.
Does the MAF switch a minimum of 200 mg/strk between 5% and 95% of EGR
actuation?
Yes → No problem found. Test complete.
No → Go To 6

Remove the EGR valve and check the valve and flow passages for debris or other
restrictions.
Yes → Clean or repair as necessary.
No → Replace the EGR Valve.

151
P2066-MASS AIR FLOW SENSOR PLAUSIBILITY — Continued


No → Go To 8
to set.
NOTE: Inspect the exhaust system and related tubes for damage, restriction
or poor connection. Any of these conditions can cause a this DTC to set.
Inspect the intake system, exhaust system and related tubes and connections.
No → Go To 9

Remove the Intake Air Temperature Sensor.
Connect smoke machine 84-04 to the Intake Air Temperature Sensor port in the
intake duct and begin injecting smoke into the intake system.
Observe all intake system components for evidence of smoke leakage.
Is there evidence of smoke leakage?
No → Replace the MAF Sensor.

152
Symptom List:
HIGH
LOW
PLAUSIBILITY AIR MASS TOO HIGH.
P2066-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO HIGH

Set Condition: The ECM detects excessive air flow from the MAF Sensor.
P2066-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO LOW

Set Condition: The ECM detects low air flow from the MAF Sensor.
POSSIBLE CAUSES
AIR FILTER
AIR RESTRICTION
MASS AIRFLOW SENSOR
153
P2066-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO HIGH —

Continued
NOTE: Inspect all air intake and turbocharger related tubes for damage,
to set.
displayed.
Yes → Go To 2
No → Go To 5


No → Go To 3
to set.
NOTE: Inspect the exhaust system and related tubes for damage, restriction
or poor connection. Any of these conditions can cause a this DTC to set.
Inspect the intake system, exhaust system and related tubes and connections.
No → Go To 4


No → Replace the MAF Sensor.

154
P2066-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO HIGH —

Continued

155
Symptom:
P2087-INTAKE PRESSURE SENSOR INTAKE RESTRICTION
P2087-INTAKE PRESSURE SENSOR INTAKE RESTRICTION

POSSIBLE CAUSES
RESTRICTED INTAKE SYSTEM
Repair Instructions:
RESTRICTED INTAKE SYSTEM

This DTC indicates a restriction in the intake system. Check for clogged air filter, collapsed
hoses, or other conditions that could cause restricted air flow through the intake system.
Repair or replace as necessary.
156
Symptom List:
P2100-FUEL PUMP RELAY CIRCUIT OPEN CIRCUIT
P2100-FUEL PUMP RELAY CIRCUIT SHORTED TO GROUND
The title for the tests will be P2100-FUEL PUMP RELAY
CIRCUIT OPEN CIRCUIT.
POSSIBLE CAUSES
ENGINE CONTROL RELAY OUTPUT CIRCUIT OPEN
FUEL LIFT PUMP RELAY
FUEL LIFT PUMP RELAY CONTROL CIRCUIT SHORTED TO GROUND
FUEL LIFT PUMP RELAY CONTROL CIRCUIT OPEN

displayed.
Crank and attempt to start the engine several times.
With the DRBIIIt, read the active ECM DTCs.
Yes → Go To 2
No → Go To 6

Remove the Fuel Lift Pump Relay.
Using a 12-volt test light connected to ground, check the Engine Control Relay
Output circuit.
Did the test light illuminate brightly?
Yes → Go To 3
No → Refer to Checking the ECM Power and Grounds for the related
symptom(s).
157
P2100-FUEL PUMP RELAY CIRCUIT OPEN CIRCUIT — Continued

Install a substitute relay in place of the Fuel Lift Pump Relay.
With the DRB, actuate the Fuel Lift Pump Relay.
Does the Fuel Lift Pump Relay cycle on and off?
Yes → Replace the Fuel Lift Pump Relay.
No → Go To 4

Measure the resistance between ground and the Fuel Lift Pump Relay Control
circuit.
Yes → Go To 5
No → Repair the Fuel Lift Pump Relay Control circuit for a short to
ground.

Measure the resistance of the Fuel Lift Pump Relay Control circuit.

No → Repair the Fuel Lift Pump Relay Control circuit for an open.

158
Symptom List:
P2100-FUEL PUMP RELAY CIRCUIT SHORTED TO VOLTAGE
P2100-FUEL PUMP RELAY EXCESSIVE CURRENT
The title for the tests will be P2100-FUEL PUMP RELAY
CIRCUIT SHORTED TO VOLTAGE.
POSSIBLE CAUSES
FUEL LIFT PUMP RELAY
FUEL LIFT PUMP RELAY CONTROL CIRCUIT SHORTED TO VOLTAGE

displayed.
Yes → Go To 2
No → Go To 3

159
P2100-FUEL PUMP RELAY CIRCUIT SHORTED TO VOLTAGE — Continued

Install a substitute relay in place of the Fuel Lift Pump Relay.
Yes → Replace the Fuel Lift Pump Relay.
No → Go To 4

connector.
Measure the voltage of the Fuel Lift Pump Relay Control circuit.
No → Repair the Fuel Lift Pump Relay Control circuit for a short to
voltage.
160
Symptom List:
P2104-STARTER RELAY CIRCUIT SHORT CIRCUIT
P2152-STARTER RELAY CIRCUIT SHORT TO GROUND
P2153-STARTER RELAY CIRCUIT OPEN OR SHORTED TO VOLT-
AGE
The title for the tests will be P2104-STARTER RELAY CIR-
CUIT SHORT CIRCUIT.
P2104-STARTER RELAY CIRCUIT SHORT CIRCUIT

When Monitored: During engine crank attempt.
Set Condition: The ECM detects too much current on the Starter Motor Relay Control
circuit.
POSSIBLE CAUSES
SUBSTITUTE STARTER RELAY
STARTER RELAY CONTROL CIRCUIT SHORTED TO GROUND
STARTER RELAY CONTROL CIRCUIT SHORTED TO VOLTAGE
STARTER RELAY CONTROL CIRCUIT OPEN

displayed.
Attempt to start the engine several times, pausing for at least 10 seconds between
each cycle.
Yes → Go To 2
No → Go To 8
161
P2104-STARTER RELAY CIRCUIT SHORT CIRCUIT — Continued

NOTE: Check the ECM for other ECM DTC’s related to circuits that are
Yes → Go To 3
No → Go To 4

Yes → Go To 4
Grounds.

Install a substitute relay in place of the Starter Relay.
Attempt to start the engine several times, pausing for at least 10 seconds between
each cycle.
Yes → Go To 5
No → Replace the Starter Relay.


Remove the Starter Relay.
Measure the resistance of the Starter Relay Control circuit.
Yes → Go To 6
No → Repair the Starter Relay Control circuit for an open.


Measure the resistance between ground and the Starter Relay Control circuit.
Yes → Go To 7
No → Repair the Starter Relay Control circuit for a short to ground.

162
P2104-STARTER RELAY CIRCUIT SHORT CIRCUIT — Continued

connector.
Measure the voltage of the Starter Relay Control circuit.

No → Repair the Starter Relay Control circuit for a short to voltage.


163
Symptom List:
P2110-BOOST PRESSURE SERVO MOTOR CIRCUIT SHORT CIR-
CUIT
P2112-BOOST PRESSURE SERVO MOTOR CIRCUIT EXCESSIVE
CURRENT
P2526-BOOST PRESSURE SERVO MOTOR SHORT TO VOLTAGE
The title for the tests will be P2110-BOOST PRESSURE
SERVO MOTOR CIRCUIT SHORT CIRCUIT.
P2110-BOOST PRESSURE SERVO MOTOR CIRCUIT SHORT CIRCUIT

Set Condition: The ECM detects a short to battery on the Boost Pressure Servo Motor
Control circuit.
POSSIBLE CAUSES
BOOST PRESSURE SERVO MOTOR
BOOST PRESSURE SERVO MOTOR CONTROL SHORT TO VOLTAGE
ENGINE CONTROL MODULE - INTERNAL
ENGINE CONTROL MODULE - INTERNAL SHORT TO VOLTAGE

displayed.
Yes → Go To 2
No → Go To 5
164
P2110-BOOST PRESSURE SERVO MOTOR CIRCUIT SHORT CIRCUIT —

Continued
Disconnect the Boost Pressure Servo Motor harness connector.
Does the DRB display BOOST PRESSURE SERVO MOTOR OPEN CIRCUIT?
Yes → Replace the Boost Pressure Servo Motor.
No → Go To 3

Measure the voltage of the Boost Pressure Servo Motor Control circuit.
No → Go To 4

connector.
Measure the voltage of the Boost Pressure Servo Motor Control circuit.

No → Repair the Boost Pressure Servo Motor Control circuit for a short
to voltage.
165
P2110-BOOST PRESSURE SERVO MOTOR CIRCUIT SHORT CIRCUIT —

Continued

166
Symptom List:
P2111-BOOST PRESSURE SERVO MOTOR CIRCUIT SHORT TO
GROUND
P2112-BOOST PRESSURE SERVO MOTOR CIRCUIT OPEN CIR-
CUIT
P2510-BOOST PRESSURE SERVO MOTOR SHORT TO GROUND
P2526-BOOST PRESSURE SERVO MOTOR OPEN CIRCUIT
P2526-BOOST PRESSURE SERVO MOTOR SHORT TO GROUND
The title for the tests will be P2111-BOOST PRESSURE
SERVO MOTOR CIRCUIT SHORT TO GROUND.
P2111-BOOST PRESSURE SERVO MOTOR CIRCUIT SHORT TO GROUND

Set Condition: The ECM detects a short to battery on the Boost Pressure Servo Motor
Control circuit.
P2112-BOOST PRESSURE SERVO MOTOR CIRCUIT OPEN CIRCUIT

Set Condition: The ECM detects an open or short to ground on the Boost Pressure Servo
Motor Control circuit.
POSSIBLE CAUSES
12 VOLT SUPPLY CIRCUIT OPEN
BOOST PRESSURE SERVO MOTOR CONTROL CIRCUIT SHORTED TO GROUND
BOOST PRESSURE SERVO MOTOR CONTROL CKT OPEN
167

GROUND — Continued
displayed.
Yes → Go To 2
No → Go To 8
Yes → Go To 3
No → Go To 4

Yes → Go To 4
Grounds.

Using a 12-volt test light connected to ground, check the 12 Volt Supply circuit in the
Boost Pressure Servo Motor harness connector.
Yes → Go To 5
No → Repair the 12 Volt Supply circuit for an open.
168

Measure the resistance between the Boost Pressure Servo Motor Control circuit in
the Boost Pressure Servo Motor harness connector and ground.
Yes → Go To 6
No → Repair the Boost Pressure Servo Motor Control circuit for a short
to ground.

Measure the resistance of the Boost Pressure Servo Motor Control circuit.
Yes → Go To 7
No → Repair the Boost Pressure Servo Motor Control circuit for an

open.

Install a substitute Boost Pressure Servo Motor in place of the vehicle’s Boost
Pressure Servo Motor.
NOTE: Ensure the ECM and Boost Pressure Servo Motor harness connec-
tors are connected.
With the DRB, check for this DTC to set again.

No → Replace the Boost Pressure Servo Motor.
169

NOTE: The conditions that set the DTC are not present at this time.The

170
Symptom List:
P2132-GLOW PLUG CONTROL MODULE CIRCUIT OPEN CIRCUIT
P2132-GLOW PLUG CONTROL MODULE CIRCUIT SHORTED TO
GROUND
P2132-GLOW PLUG CONTROL MODULE CIRCUIT SHORTED TO
VOLTAGE OR OPEN
P2132-GLOW PLUG CONTROL MODULE FAULT
The title for the tests will be P2132-GLOW PLUG CONTROL
MODULE CIRCUIT OPEN CIRCUIT.
POSSIBLE CAUSES
BATTERY SUPPLY CIRCUIT OPEN
GROUND CIRCUIT OPEN
GLOW PLUG CONTROL MODULE

displayed.
Repeat this test several times.
Yes → Go To 2
No → Go To 4

Disconnect the Glow Plug Control Module harness connector.
Using a 12-volt test light connected to 12-volts, check the Ground circuit at the Glow
Plug Control Module harness connector.
Yes → Go To 3
No → Repair the Glow Plug Control Module Ground circuit for an open.
171
P2132-GLOW PLUG CONTROL MODULE CIRCUIT OPEN CIRCUIT —

Continued
Disconnect the Glow Plug Control Module harness connector.
Using a 12-volt test light connected to ground, check the Battery Supply circuit at the
Glow Plug Control Module harness connector.
Yes → Replace the Glow Plug Control Module.
No → Repair the Glow Plug Control Module Battery Supply circuit for
an open.


172
Symptom List:
P2151-FUEL PRESS SOLENOID SIGNAL PLAUSIBILITY HIGH
P2151-FUEL PRESS SOLENOID SIGNAL PLAUSIBILITY LOW
P2500-FUEL PRESSURE SOLENOID CIRCUIT OPEN CIRCUIT
P2501-FUEL PRESSURE SOLENOID CIRCUIT SHORTED TO
GROUND OR B+
The title for the tests will be P2151-FUEL PRESS SOLENOID
SIGNAL PLAUSIBILITY HIGH.
P2500-FUEL PRESSURE SOLENOID CIRCUIT OPEN CIRCUIT

Set Condition: The ECM detects an open or short to ground on the Fuel Pressure Solenoid
Control circuit.
P2501-FUEL PRESSURE SOLENOID CIRCUIT SHORTED TO GROUND OR B+

When Monitored: With the ignition on and the ECM attempting to actuate the Fuel
Pressure Solenoid.
Set Condition: The ECM detects excessive current on the Fuel Pressure Solenoid Control
circuit when attempting to actuate the Fuel Pressure Solenoid.
POSSIBLE CAUSES
FUEL PRESSURE SOLENOID CONTROL SHORTED TO VOLTAGE
FUEL PRESSURE SOLENOID CONTROL CIRCUIT SHORTED TO GROUND
FUEL PRESSURE SOLENOID CONTROL CIRCUIT OPEN
173
P2151-FUEL PRESS SOLENOID SIGNAL PLAUSIBILITY HIGH —

Continued
displayed.
LEAKS.
Start the engine several times, turning the ignition off for at least 30 seconds
between each run cycle.
Yes → Go To 2
No → Go To 8
Yes → Go To 3
No → Go To 4

Yes → Go To 4
Grounds.
174

Continued
Disconnect the Fuel Pressure Solenoid harness connector.
connector.
Measure the voltage of the Fuel Pressure Solenoid Control circuit.
Yes → Go To 5
No → Repair the Fuel Pressure Solenoid Control circuit for a short to
voltage.

Measure the resistance between ground and the Fuel Pressure Solenoid Control
circuit.
Measure the resistance between ground and the Fuel Pressure Solenoid 12-volt
Supply
Yes → Go To 6
No → Repair the Fuel Pressure Solenoid circuit(s) for a short to ground.

Measure the resistance of the Fuel Pressure Solenoid Control circuit.
Measure the resistance of the Fuel Pressure Solenoid 12-volt Supply circuit.
Yes → Go To 7
No → Repair the Fuel Pressure Solenoid circuit(s) for an open.

175

Continued
NOTE: The DRB should display P2500-FUEL PRESSURE SOLENOID OPEN
CIRCUIT.
Connect a jumper wire between cavity 1 and cavity 2 of the Fuel Pressure Solenoid
harness connector.
NOTE: The DRB should display P2501-FUEL PRESSURE SOLENOID
SHORT CIRCUIT.
Does the DRB display the appropriate DTC for each condition?
Yes → Replace the Fuel Pressure Solenoid in accordance with the


176
Symptom List:
P2197-FUEL QUANTITY SOLENOID OPEN CIRCUIT
P2198-FUEL QUANTITY SOLENOID SHORT TO VOLTAGE
P2199-FUEL QUANTITY SOLENOID SHORT TO GROUND
P2502-FUEL QUANTITY SOLENOID SHORT TO GROUND
The title for the tests will be P2197-FUEL QUANTITY SOLE-
NOID OPEN CIRCUIT.
POSSIBLE CAUSES
FUEL QUANTITY SOLENOID
FUEL QUANTITY SOLENOID CIRCUIT(S) SHORTED TO GROUND
FUEL QUANTITY SOLENOID CIRCUIT(S) SHORTED TO VOLTAGE
FUEL QUANTITY SOLENOID CIRCUIT(S) SHORTED TOGETHER
FUEL QUANTITY SOLENOID OPEN CIRCUIT(S)

Yes → Go To 2
No → Go To 7
177
P2197-FUEL QUANTITY SOLENOID OPEN CIRCUIT — Continued


Go To 3

Disconnect the Fuel Quantity Solenoid harness connector.
Measure the resistance of each of the Fuel Quantity Solenoid circuits between the
ECM harness connector and the Fuel Quantity Solenoid harness connector.
Yes → Go To 4
No → Repair the circuit(s) that measured above 10.0 ohms for an open.

Measure the resistance between ground and each of the Fuel Quantity Solenoid
circuits.
Is the resistance above 1000 ohms for each measurement?
Yes → Go To 5
ground.

Measure the resistance between the Fuel Quantity Solenoid circuits.
Yes → Go To 6
No → Repair the Fuel Quantity Solenoid circuits for a short together.

178
P2197-FUEL QUANTITY SOLENOID OPEN CIRCUIT — Continued

connector.
Measure the voltage each of the Fuel Quantity Solenoid circuits.
Is the voltage below 1.0 volt for each measurement?
Yes → Replace the Fuel Quantity Solenoid in accordance with the

No → Repair the circuit(s) that measured above 1.0 volts for a short to
voltage.


179
Symptom List:
P2203-TORQUE REDUCTION MESSAGE FROM ABS - CAN PLAUSI-
BILITY
P2203-TORQUE REDUCTION MESSAGE FROM ABS - MESSAGE
ERROR
P2203-TORQUE REDUCTION MESSAGE FROM ABS - MESSAGES
MISSING
P2203-TORQUE REDUCTION MESSAGE FROM ABS - NO COMMUN-
IOCATION
P2203-TORQUE REDUCTION MESSAGE FROM ABS - PLAUSIBIL-
ITY #1
P2203-TORQUE REDUCTION MESSAGE FROM ABS PLAUSIBILITY
#2
P2208-ABS BRAKE SIGNAL CAN MESSAGE IMPLAUSIBLE
P2208-ABS CAN BRAKE SIGNAL PLAUSIBILITY
P2209-ABS CAN MESSAGE MISSING OR INCORRECT
P2253-STEERING ANGLE SENSOR PLAUSIBILITY
The title for the tests will be P2203-TORQUE REDUCTION
MESSAGE FROM ABS - CAN PLAUSIBILITY.
POSSIBLE CAUSES
CAB DTCS
VERIFY CAB COMMUNICATION

With the DRBIIIt attempt to communicate with the CAB.
NOTE: If there are other DTCs set with this DTC, refer to the Symptom List
and repair other stored ECM DTCs before diagnosing this DTC.
Is the CAB communicating with the DRB?
Yes → Go To 2
No → Refer to the appropriate symptom in the Body Diagnostic Infor-
mation.
180
P2203-TORQUE REDUCTION MESSAGE FROM ABS - CAN PLAUSIBIL-

ITY — Continued
With the DRBIIIt, read the CAB DTCs.
Are there any CAB DTCs?
Yes → Refer to symptom list for problems related to CAB.

No → Go To 3
displayed.
Turn the ignition off then turn the ignition on and wait 60 seconds.
No → Go To 4


181
Symptom List:
P2204-TORQUE REDUCTION MESSAGE FROM TCM - CAN PLAU-
SIBILITY
P2204-TORQUE REDUCTION MESSAGE FROM TCM - ENGINE
STOP
P2204-TORQUE REDUCTION MESSAGE FROM TCM - MESSAGE
ERROR
P2204-TORQUE REDUCTION MESSAGE FROM TCM - MESSAGES
MISSING
P2204-TORQUE REDUCTION MESSAGE FROM TCM - PLAUSIBIL-
ITY
P2204-TORQUE REDUCTION MESSAGE FROM TCM - TCM DTC #1
P2204-TORQUE REDUCTION MESSAGE FROM TCM - TCM DTC #2
MESSAGE FROM TCM - CAN PLAUSIBILITY.
POSSIBLE CAUSES
TCM DTCS
VERIFY TCM COMMUNICATION

With the DRBIIIt attempt to communicate with the TCM.
Is the TCM communicating with the DRB?
Yes → Go To 2

mation.

With the DRBIIIt, read the TCM DTCs.
Are there any TCM DTCs?
Yes → Refer to symptom list for problems related to TCM.

No → Go To 3
182
P2204-TORQUE REDUCTION MESSAGE FROM TCM - CAN PLAUSIBIL-

ITY — Continued
displayed.

No → Go To 4


183
Symptom List:
P2210-ESM CAN MESSAGE MISSING OR INCORRECT
P2234-ABS DTC EXTERNAL QUANTITY CONTROL FAULT
PRESENT
P2252-LATERAL ACCELERATOR SENSOR PLAUSIBILTY
The title for the tests will be P2210-ESM CAN MESSAGE
MISSING OR INCORRECT.
POSSIBLE CAUSES
ABS MODULE
CAN BUS CIRCUITS OPEN
ABS DTCS

displayed.
NOTE: This DTC indicates a communication problem between the TCM and
the ECM.
Yes → Go To 2
No → Go To 4

With the DRBIIIt, attempt to read ABS DTCs.
NOTE: If the DRB is unable to communicate with the ABS Module, refer to
the symptom list for problem related to ABS Module Communication.
Are there any ABS DTCs?
Yes → Refer to symptom list for problems related to ABS DTC’s.
No → Go To 3
184
P2210-ESM CAN MESSAGE MISSING OR INCORRECT — Continued

Disconnect the ABS Module harness connectors.
and connectors to the ABS Module. Inspect the ABS harness connector and
associated wiring for signs of poor terminal contact.
Measure and note the voltage of both CAN Bus circuit at the ABS Module harness
connector.
Is the voltage between 2.2 volts and 2.8 volts for each measurement?

No → Repair the CAN Bus circuit(s) for an open.


185
Symptom List:
P2211-ETC CAN MESSAGE MISSING OR INCORRECT
P2258-TCM MESSAGE ERROR
P2258-TCM NO CAN MESSAGE
The title for the tests will be P2211-ETC CAN MESSAGE
MISSING OR INCORRECT.
POSSIBLE CAUSES
TRANSMISSION CONTROL MODULE
TCM DTCS

displayed.
NOTE: This DTC indicates a communication problem between the TCM and
the ECM.
Yes → Go To 2
No → Go To 4

With the DRBIIIt, attempt to read TCM DTCs.
NOTE: If the DRB is unable to communicate with the TCM, refer to the
symptom list for problem related to TCM Communication.
Are there any TCM DTCs?
Yes → Refer to symptom list for problems related to TCM DTC’s.

No → Go To 3
186
P2211-ETC CAN MESSAGE MISSING OR INCORRECT — Continued

Disconnect the TCM harness connectors.
Measure and note the voltage of both CAN Bus circuit at the TCM harness connector.
and connectors to the Transmission Control Module. Inspect the Transmis-
sion Control Module harness connector and associated wiring for signs of
poor terminal contact.



187
Symptom List:
P2217-TCM DTC INTERNAL FAULT PRESENT
P2218-TCM DTC 1-2 AND 4-5 SHIFT SOLENOID FAULT PRESENT
P2219-TCM DTC 2-3 SHIFT SOLENOID FAULT PRESENT
P2220-TCM DTC 3-4 SHIFT SOLENOID FAULT PRESENT
P2221-TCM DTC TORQUE CONVERTER CLUTCH SOLENOID
FAULT PRESENT
P2222-TCM DTC MODULATING PRESSURE SOLENOID FAULT
PRESENT
P2223-TCM DTC SHIFT PRESSURE SOLENOID FAULT PRESENT
P2224-TCM DTC VALVE VOLTAGE SUPPLY FAULT PRESENT
P2225-TCM DTC SPEED SENSOR VOLTAGE FAULT PRESENT
P2226-TCM DTC EWM CAN MESSAGE FAULT PRESENT
P2227-TCM DTC RIGHT REAR WHEEL SPEED IMPLAUSIBLE
FAULT PRESENT
P2228-TCM DTC TRANSMISSION RATIO ERROR FAULT PRESENT
P2229-TCM DTC CAN MSG IMPLAUSIBLE FAULT PRESENT
P2230-TCM DTC TCC EXCESSIVE POWER CONSUMPTION FAULT
PRESENT
P2231-TCM DTC NOT UNEQUIVOCAL FAULT PRESENT
P2232-TCM DTC NEGATIVE GEAR COMPARISON FAULT PRESENT
The title for the tests will be P2217-TCM DTC INTERNAL
FAULT PRESENT.
POSSIBLE CAUSES
VERIFY CURRENT DTC
188
P2217-TCM DTC INTERNAL FAULT PRESENT — Continued

displayed.
NOTE: This code was set in the ECM by the Transmission Control Module to
indicate a transmission fault. Diagnosis of transmission faults should be
done using the Transmission Diagnostic Information.
NOTE: When repairs have been completed, the ECM and TCM must have
codes cleared.
With the DRBIIIt, erase ECM DTCs only.
Are there any TCM DTCs present in the ECM?
Yes → Refer to Transmission Diagnostic Information for the related

symptom(s).
Perform NAG1 TRANSMISSION VERIFICATION TEST - VER 1.
189
Symptom List:
P2240-ABS STEERING ANGLE SENSOR CAN MESSAGE IMPLAUSI-
BLE 1
P2240-ABS STEERING ANGLE SENSOR CAN MESSAGE IMPLAUSI-
BLE 2
The title for the tests will be P2240-ABS STEERING ANGLE
SENSOR CAN MESSAGE IMPLAUSIBLE 1.
POSSIBLE CAUSES
STEERING ANGLE SENSOR

displayed.
NOTE: This DTC indicates a communication problem between the Steering
Angle Sensor and the ECM.
Yes → Go To 2
No → Go To 3

Disconnect the Steering Angle Sensor harness connector.
and connectors to the Steering Angle Sensor. Inspect the Steering Angle
Sensor harness connector and associated wiring for signs of poor terminal
contact.
Measure and note the voltage of both CAN Bus circuit at the Steering Angle Sensor
harness connector.


190
P2240-ABS STEERING ANGLE SENSOR CAN MESSAGE IMPLAUSIBLE 1

— Continued

191
Symptom List:
P2242-ABS BRAKE MESSAGE PLAUSIBILITY 1
P2242-ABS BRAKE MESSAGE PLAUSIBILITY 2
The title for the tests will be P2242-ABS BRAKE MESSAGE
PLAUSIBILITY 1.
POSSIBLE CAUSES
CAB DTCS
CHECKING BRAKE SWITCH INPUT
CONTROLLER ANTILOCK BRAKE MODULE
TCM DTCS
VERIFY TCM COMMUNICATION

1 NOTE: This DTC can be set if the vehicle operator depresses the brake pedal All
and the accelerator at the same time (riding the brake pedal). Check with
vehicle operator for this type of driving behavior.
Yes → Go To 2

mation.


No → Go To 3

With the DRBIIIt attempt to communicate with the TCM.
Is the TCM communicating with the DRB?
Yes → Go To 4

mation.
192
P2242-ABS BRAKE MESSAGE PLAUSIBILITY 1 — Continued

Yes → Refer to symptom list for problems related to TCM

No → Go To 5

With the DRBIIIt select TCM then Sensors. Read the Brake Switch input while
pressing and releasing the brake pedal several times.
With the DRBIIIt select CAB then Sensors. Read the Brake Switch input while
pressing and releasing the brake pedal several times.
Is the Brake Switch input operating correctly for both modules?
Yes → Replace and program the CAB in accordance with the Service
Information.
No → Refer to the Service Information wiring to diagnose brake switch
problem.
193
Symptom:
P2244-INSTRUMENT CLUSTER MESSAGE PLAUSIBILITY
POSSIBLE CAUSES
INSTRUMENT CLUSTER DTCS
VERIFY INSTRUMENT CLUSTER COMMUNICATION

With the DRBIIIt attempt to communicate with the Instrument Cluster.
Is the Instrument Cluster communicating with the DRB?
Yes → Go To 2
mation.

With the DRBIIIt, read the Instrument Cluster DTCs.
Are there any Instrument Cluster DTCs?
Yes → Refer to symptom list for problems related to Instrument Cluster.

No → Go To 3
displayed.

No → Go To 4
194
P2244-INSTRUMENT CLUSTER MESSAGE PLAUSIBILITY — Continued


195
Symptom List:
P2259-TORQUE REDUCTION MESSAGE FROM HVAC- PARITY ER-
ROR
P2259-TORQUE REDUCTION MESSAGE FROM HVAC- SWITCH
SIGNAL ERROR
P2259-TORQUE REDUCTION MESSAGE FROM HVAC- SWITCH
SIGNAL PLAUSIBILITY
MESSAGE FROM HVAC- PARITY ERROR.
POSSIBLE CAUSES
AUTOMATIC TEMP CONTROL DTC

1 NOTE: This DTC indicates the presents of a problem or DTC in the ATC All
Module.
View repair statement.
Yes → Refer to symptom list for problems related to Automatic Temper-
ature Control.
196
Symptom:
P229-INSTRUMENT CLUSTER MESSAGE - AMBIENT TEMPERA-
TURE SIGNAL PLAUSIBILITY
POSSIBLE CAUSES
INSTRUMENT CLUSTER DTC

1 NOTE: This DTC indicates the presents of a problem with the Ambient Temp All
Sensor input to the Instrument Cluster.
View repair statement.
Yes → Refer to symptom list for problems related to Instrument Cluster.

197
Symptom:
POSSIBLE CAUSES
SENSOR SUPPLY VOLTAGE 2 SHORTED TO VOLTAGE

displayed.
Start the engine.
Yes → Go To 2
No → Go To 6

Visually inspect the wiring and connectors associated with the Boost Pressure Sensor
and Fuel Pressure Sensor for problems that may result in a short circuit.
No → Go To 3

Disconnect the Boost Pressure Sensor and Fuel Pressure Sensor harness connectors.
Measure the voltage at all circuits in the Fuel Pressure Sensor and Boost Pressure
Sensor harness connector cavities.
voltage.
No → Go To 4
198

Yes → Go To 5
No → Replace the Fuel Pressure Sensor in accordance with the Service

Information.

Disconnect the Boost Pressure Sensor harness connector.

No → Replace the Boost Pressure Sensor.

199
Symptom:
POSSIBLE CAUSES
SENSOR SUPPLY VOLTAGE 2 SHORTED TO GROUND
BOOST PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND CIRCUIT
FUEL PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND CIRCUIT

displayed.
Yes → Go To 2
No → Go To 8

Visually inspect the wiring and connectors associated with the Boost Pressure Sensor
and Fuel Pressure Sensor for problems that may result in a short circuit.

No → Go To 3

Disconnect the Boost Pressure Sensor and Fuel Pressure Sensor harness connectors.
Measure the resistance between ground and all of the Fuel Pressure Sensor and
Boost Pressure Sensor harness connector cavities.
ground.
No → Go To 4
200

Measure the resistance between the Sensor Ground circuit and the Fuel Pressure
Sensor Signal circuit at the Fuel Pressure Sensor harness connector.
Yes → Go To 5
No → Repair the Fuel Pressure Sensor Signal circuit for a short to the

Measure the resistance between the Sensor Ground circuit and the Boost Pressure
Sensor Signal circuit at the Boost Pressure Sensor harness connector.
Yes → Go To 6
No → Repair the Boost Pressure Sensor Signal circuit for a short to the

Yes → Go To 7
No → Replace the Boost Pressure Sensor.


No → Replace the Fuel Pressure Sensor.

201


202
Symptom:
POSSIBLE CAUSES
ENGINE OIL SENSOR
INTAKE AIR PRESSURE SENSOR
SENSOR SUPPLY VOLTAGE 3 SHORTED TO GROUND
ENGINE OIL SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND CIRCUIT
INTAKE AIR PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND CIRCUIT

displayed.
Yes → Go To 2
No → Go To 8

Visually inspect the wiring and connectors associated with the Intake Air Pressure
Sensor and Engine Oil Sensors for problems that may result in a short circuit.

No → Go To 3

Disconnect the Intake Air Pressure Sensor and Engine Oil Sensor harness connec-
tors.
Measure the resistance between ground and all of the EOS and Intake Air Pressure
ground.
No → Go To 4
203

Measure the resistance between the Sensor Ground circuit and the Engine Oil Sensor
Signal circuit at the Engine Oil Sensor harness connector.
Yes → Go To 5
No → Repair the Engine Oil Sensor Signal circuit for a short to the

Disconnect the Intake Air Pressure Sensor harness connector.
Measure the resistance between the Sensor Ground circuit and the Intake Air
Pressure Sensor Signal circuit at the Intake Air Pressure Sensor harness connector.
Yes → Go To 6
No → Repair the Intake Air Pressure Sensor Signal circuit for a short to
the Sensor Ground circuit.

Yes → Go To 7
No → Replace the Intake Air Pressure Sensor.


No → Replace the Engine Oil Sensor.

204


205
Symptom:
POSSIBLE CAUSES
EO SENSOR
INTAKE AIR PRESSURE SENSOR
SENSOR SUPPLY VOLTAGE 3 SHORTED TO VOLTAGE

displayed.
Start the engine.
Yes → Go To 2
No → Go To 6

Visually inspect the wiring and connectors associated with the Intake Air Pressure
Sensor and Engine Oil Sensors for problems that may result in a short circuit.
No → Go To 3
206

Disconnect the Intake Air Pressure Sensor and Engine Oil Sensor harness connec-
tors.
Measure the voltage at all circuits in the Engine Oil Sensor and Intake Air Pressure
voltage.
No → Go To 4

Yes → Go To 5
No → Replace the Engine Oil Sensor.


No → Replace the Intake Air Pressure Sensor.
207


208
Symptom List:
P2333-S/C VEHICLE SPEED PLAUSIBILITY
P2338-S/C EXCESSIVE ACCELERATION
P2338-S/C EXCESSIVE DECELERATION
The title for the tests will be P2333-S/C VEHICLE SPEED
PLAUSIBILITY.
POSSIBLE CAUSES
BRAKE SWITCH VERIFICATION
CAB DTCS
OPEN CAN BUS CIRCUITS
WHEEL SPEED VERIFICATION

displayed.
Test drive the vehicle and attempt to duplicate the problem.
With the DRB, read ECM DTC’s.
Yes → Go To 2
No → Go To 7

Yes → Go To 3
mation.
209
P2333-S/C VEHICLE SPEED PLAUSIBILITY — Continued


No → Go To 4

Disconnect the CAB Module harness connector.
Measure the resistance of each CAN Bus circuit between the ECM harness connector
and the CAB harness connector.
Yes → Go To 5
No → Repair the open CAN Bus circuit(s) between the ECM and the
SKREEM.
5 With the DRBIIIt, perform the Wheel Speed Test of the ABS system. All
Yes → Repair wheel speed signal problem as necessary.

No → Go To 6
6 Check the Brake Switch for proper operation and adjustment. All
Yes → Adjust or replace the Brake Switch as necessary.


210
Symptom List:
P2339-ECM CHECKSUM ERROR #1
P2339-ECM CHECKSUM ERROR #2
P2339-ECM INVALID CODING
P2339-ECM INVALID DATA
The title for the tests will be P2339-ECM CHECKSUM ERROR
#1.
POSSIBLE CAUSES

1 NOTE: This DTC indicates that an error occurred during ECM program- All
ming.
Refer to the Service Information and attempt to reprogram the ECM.
211
Symptom:
P2344-KICKDOWN SWITCH PLAUSIBILITY
POSSIBLE CAUSES

displayed.
NOTE: If there are any Accelerator Pedal Position Sensor DTC’s present,
repair the APP Sensor DTC’s before continuing.
Test drive the vehicle. Be sure to completely depress the accelerator pedal several
times to activate the Kickdown Switch.
No → Go To 2


212
Symptom List:
P2347-AUTOMATIC TRANSMISSION CODED AS MANUAL TRANS-
MISSION
P2347-CAN BUS CIRCUIT INTERUPTION
P2347-MANUAL TRANSMISSIO CODED AS AUTO TRANSMISSION
P2347-WRITE ERROR TO EEPROM
The title for the tests will be P2347-AUTOMATIC TRANSMIS-
SION CODED AS MANUAL TRANSMISSION.
POSSIBLE CAUSES
VERIFY ECM PROGRAMMING

1 Turn the Ignition on. All
With the DRBIIIt, verify that the ECM is properly coded for the options and
components that the vehicle is equipped with.
NOTE: Reprogram the ECM with correct information if necessary.
Start and idle the engine.
213
Symptom:
P2351-ECM SUPPLY VOLTAGE TOO LOW
POSSIBLE CAUSES
ECM
ECM IGNITION CIRCUIT OPEN
STARTER OR LIFT PUMP RELAY CIRCUIT(S) SHORTED TO GROUND

displayed.
Yes → Go To 2
No → Go To 4

Remove the Starter Relay and disconnect the Fuel Lift Pump harness connector
Measure the resistance between ground and the Starter Relay control circuit.
Measure the resistance between ground and the Fuel Lift Pump Relay control circuit.
Did both circuits measure above 1000 ohms?
Yes → Go To 3
No → Repair the relay control circuit(s) that did not measure above
1000 ohms for a short to ground.

Using the Service Wiring Information determine which circuits in the ECM harness
connector provide Ignition Switch power to the ECM.
Using a 12-volt test light connected to ground, check each Ignition Switch Output
circuits in the ECM harness connectors.

No → Repair the Ignition Supply circuit as necessary.
214
P2351-ECM SUPPLY VOLTAGE TOO LOW — Continued


215
Symptom List:
P2359-BOOST PRESSURE TOO HIGH
P2359-BOOST PRESSURE TOO LOW
The title for the tests will be P2359-BOOST PRESSURE TOO
HIGH.
POSSIBLE CAUSES
AIR FILTER
AIR RESTRICTION
TURBOCHARGER

displayed.
Monitor the DRBIIIt for ECM DTCs.
Yes → Go To 2
No → Go To 6

No → Go To 3
216
P2359-BOOST PRESSURE TOO HIGH — Continued

to set.
No → Go To 4

No → Go To 5

Replace the Boost Pressure Servo Motor in accordance with the Service Information.
NOTE: Ensure the ECM and Boost Pressure Servo Motor harness connec-
tors are connected.
Yes → Replace the Turbocharger assembly in accordance with the Ser-

vice Information.
No → Replace the Boost Pressure Servo Motor.

217
Symptom List:
P2511-EGR VALVE SIGNAL CIRCUIT SHORTED TO GROUND
P2527-EGR VALVE SIGNAL CIRCUIT OPEN CIRCUIT
P2527-EGR VALVE SIGNAL CIRCUIT SHORTED TO GROUND
The title for the tests will be P2511-EGR VALVE SIGNAL
CIRCUIT SHORTED TO GROUND.
POSSIBLE CAUSES
ENGINE CONTROL RELAY OUTPUT CIRCUIT OPEN
EGR VALVE CONTROL CIRCUIT SHORTED TO GROUND
EGR VALVE CONTROL CIRCUIT OPEN
EGR SOLENOID

displayed.
Perform several ignition cycles, turning the ignition off for at least 10 seconds
between each ignition cycle.
Yes → Go To 2
No → Go To 8
Yes → Go To 3
No → Go To 4
218
P2511-EGR VALVE SIGNAL CIRCUIT SHORTED TO GROUND — Continued

Yes → Go To 4
Grounds.

Disconnect the EGR Valve harness connector.
Using a 12-volt test light connected to ground, check the Engine Control Relay
Output circuit in the EGR Valve harness connector.
Yes → Go To 5
No → Repair the Engine Control Relay Output circuit for an open.

Measure the resistance between the EGR Valve Control circuit in the EGR Valve
harness connector and ground.
Yes → Go To 6
No → Repair the EGR Valve Control circuit for a short to ground.

Measure the resistance of the EGR Valve Control circuit.
Yes → Go To 7
No → Repair the EGR Valve Control circuit for an open.
219
P2511-EGR VALVE SIGNAL CIRCUIT SHORTED TO GROUND — Continued

Install a substitute EGR Solenoid in place of the vehicle’s EGR Solenoid.
NOTE: Ensure the ECM and EGR Valve harness connectors are connected.
No → Replace the EGR Solenoid.

220
Symptom List:
P2514-CRANKCASE VENT HEATER OPEN CIRCUIT
P2514-CRANKCASE VENT HEATER SHORTED TO GROUND
P2514-CRANKCASE VENT HEATER SHORTED TO VOLTAGE
The title for the tests will be P2514-CRANKCASE VENT
HEATER OPEN CIRCUIT.
POSSIBLE CAUSES
CRANKCASE VENT HEATER SHORTED TO VOLTAGE
CRANKCASE VENT HEATER CIRCUIT SHORTED TO GROUND
CRANKCASE HEATER VENT CIRCUIT(S) OPEN
CRANCASE VENT HEATER

displayed.
NOTE: The engine should be cold for this test to be accurate.
Yes → Go To 2
No → Go To 7
221
P2514-CRANKCASE VENT HEATER OPEN CIRCUIT — Continued


Go To 3

Disconnect the Crankcase Vent Heater harness connector.
Measure the resistance of the both circuits between the Crankcase Vent Heater
harness connector and the ECM harness connector.
Yes → Go To 4
No → Repair the Crankcase Vent Heater circuit(s) for an open.

Measure the resistance between ground and both of the Crankcase Vent Heater
circuits.
Is the resistance above 1000 ohms for each circuit?
Yes → Go To 5
No → Repair the Crankcase Vent Heater circuit(s) for a short to ground.


Measure the voltage of the both Crankcase Vent Heater circuits.
Is the voltage below 1.0 volt for each circuit?
Yes → Go To 6
No → Repair the Crankcase Vent Heater circuit for a short to voltage.

222
P2514-CRANKCASE VENT HEATER OPEN CIRCUIT — Continued

Install a substitute Crankcase Vent Heater in place of the vehicle’s existing
Crankcase Vent Heater.
NOTE: Ensure the ECM and Crankcase Vent Heater harness connectors are
connected.
With the engine cold, start and idle the engine.

No → Replace the initial Crankcase Vent Heater.


223
Symptom:
P2521-IMPROPER START ATTEMPT
POSSIBLE CAUSES
VERIFY ACTIVE DTC

displayed.
NOTE: This DTC indicates that engine rotation has occurred without an
ignition switch Start input. This can occurred when an attempt to start the
vehicle using a push start method.
NOTE: Consult with the customer to determine if a push start has been
attempted.

224
Symptom:
P2527-EGR VALVE SIGNAL CIRCUIT SHORTED TO VOLTAGE
POSSIBLE CAUSES
EGR SOLENOID
EGR VALVE CONTROL SHORTED TO VOLTAGE
ENGINE CONTROL MODULE - INTERNAL
ENGINE CONTROL MODULE - INTERNAL SHORT TO VOLTAGE

displayed.
Yes → Go To 2
No → Go To 5

Does the DRB display an EGR OPEN CIRCUIT DTC?
Yes → Replace the EGR Solenoid.

No → Go To 3

Measure the voltage of the EGR Valve Control circuit at the EGR Valve harness
connector.

No → Go To 4
225
P2527-EGR VALVE SIGNAL CIRCUIT SHORTED TO VOLTAGE — Continued

4 NOTE: If DTC P1611 or P2306 is present with this DTC, diagnose DTCs P1611 All
and P2306 before diagnosing this DTC.
connector.
Measure the voltage of the EGR Valve Control circuit.

No → Repair the EGR Valve Control circuit for a short to voltage.


226
Symptom List:
P2531-FUEL INJECTOR 1 READ TOO LARGE
P2531-FUEL INJECTOR 1 READ TOO SMALL
The title for the tests will be P2531-FUEL INJECTOR 1 READ
TOO LARGE.
POSSIBLE CAUSES
FUEL INJECTOR
227
P2531-FUEL INJECTOR 1 READ TOO LARGE — Continued

displayed.
NOTE: This DTC indicates an internal ECM problem except in the case of
DTC P0606 where it may indicate a fuel injector problem. Using the Service
Information, check the fuel injectors for leakage before replacing the ECM.
Yes → Replace the Fuel Injector identified in the DTC in accordance

No → Go To 2


228
Symptom:
P2606-CMP/CKP SYNCHRONIZATION ERROR
POSSIBLE CAUSES
CAMSHAFT POSITION SENSOR SIGNAL PROBLEM
CRANKSHAFT POSITION SENSOR SIGNAL PROBLEM
DAMAGED CKP SENSOR
DAMAGED CMP SENSOR OR CAMSHAFT
GEAR ALIGNMENT PROBLEM

displayed.
Does the DRB III display this DTC?
Yes → Go To 3
No → Go To 2

Does the DRB III display this DTC?
Yes → Go To 3
No → Go To 8
Remove the CMP Sensor.
Inspect the CMP Sensor for conditions such as loose mounting screws, damage or
debris, also check the camshaft for cracked teeth.

No → Go To 4
229
P2606-CMP/CKP SYNCHRONIZATION ERROR — Continued

Remove the CKP Sensor.
Inspect the CKP Sensor for conditions such as loose mounting screws, damage or
debris.
No → Go To 5

Using the DRB lab scope, backprobe the CMP Sensor Signal circuit at the CMP
Sensor harness connector.
NOTE: Refer to Charts and Graphs to view a correct CMP Sensor signal.
Does the DRB display a steady clean CMP Signal pattern?
Yes → Go To 6
No → Perform Test for DTC P2043-Camshaft Position Sensor Circuit

Static Plausibility.

Using the DRB lab scope, backprobe both of the CKP Sensor Signal circuits at the
CKP Sensor harness connector.
Does the DRB display a steady clean CKP Signal pattern for each circuit?
Yes → Go To 7
No → Perform Test for DTC P2045-Crankshaft Position Sensor Circuit

Dynamic Plausibility.
7 Refer to the Service Information and check alignment of the camshaft sprocket, All
crankshaft sprocket and injection pump sprocket.
Are all of the sprockets aligned correctly?

No → Repair or adjust as necessary.
230
P2606-CMP/CKP SYNCHRONIZATION ERROR — Continued


231
Symptom:
*CHECKING THE FUEL PRESSURE SENSOR CIRCUITS
POSSIBLE CAUSES
OPEN CIRCUITS

partially broken wires. Repair as necessary.
out, or corroded terminals. Repair as necessary.
Measure the resistance of each of the three Fuel Pressure Sensor circuits between the
ECM harness connector and the Fuel Pressure Sensor harness connector.
No → Repair open circuit(s) as necessary.

232
Symptom:
*CHECKING THE FUEL PRESSURE SOLENOID CIRCUITS
POSSIBLE CAUSES
FUEL PRESSURE SOLENOID RESISTANCE
OPEN CIRCUITS

Measure the resistance of both Fuel Pressure Solenoid circuits between the ECM
harness connector and the Fuel Pressure Solenoid harness connector.
Yes → Go To 2


Measure the resistance of the Fuel Pressure Solenoid.
Is the resistance between 3.5 and 5.5 ohms?

No → Replace the Fuel Pressure Solenoid.
233
Symptom:
*CHECKING THE FUEL QUANTITY SOLENOID CIRCUITS
POSSIBLE CAUSES
OPEN CIRCUITS

Measure the resistance of both Fuel Quantity Solenoid circuits between the ECM
harness connector and the Fuel Quantity Solenoid harness connector.

234
Symptom:
*CHECKING THE POWER AND GROUNDS
POSSIBLE CAUSES
EC RELAY OUTPUT CIRCUIT
ECM GROUND CIRCUIT(S) OPEN
ECM OUTPUT SHORTED - FUSE 16
ENGINE CONTROL RELAY
ENGINE CONTROL RELAY B+ SUPPLY
ENGINE CONTROL RELAY CONTROL CIRCUIT OPEN
ENGINE CONTROL RELAY CONTROL CIRCUIT SHORT TO VOLTAGE
ENGINE CONTROL RELAY OUTPUT CIRCUIT(S) OPEN
ENGINE CONTROL RELAY OUTPUT CKT SHORTED TO GROUND FUSE #16
ENGINE CONTROL RELAY OUTPUT CKT SHORTED TO GROUND FUSE #17
IGNITION SWITCH START OUTPUT CIRCUIT OPEN
IGNITION SWITCH START/RUN OUTPUT CIRCUIT OPEN
SHORTED COMPONENT

Using a 12-volt test light connected to 12-volts, check each of the ECM ground
circuits in ECM harness connector C2 cavities 2, 4 and 6.
Did the test light illuminate brightly for each cavity?
Yes → Go To 2
No → Repair the ECM Ground circuit(s) for an open.


Turn the ignition switch to the Start position.
Using a 12-volt test light connected to ground, check the Fused Ignition Switch Start
Output circuit in ECM C2 harness connector cavity 36.
Yes → Go To 3
No → Repair the Ignition Switch Start Output circuit for an open.

235
*CHECKING THE POWER AND GROUNDS — Continued

Turn the ignition switch to the Start position.
Using a 12-volt test light connected to ground, check the Fused Ignition Switch
Start/Run Output circuit in ECM C2 harness connector cavity 19.
Repeat the previous step with the ignition switch in the Run position.
Does the test light illuminate brightly in the Start and Run positions?
Yes → Go To 4
No → Repair the Ignition Switch Start/Run Output circuit for an open.


Remove the Engine Control Relay from Fuse Block No. 1.
Using a 12-volt test light connected to 12-volts, check the Engine Control Relay
Control circuit in the Engine Control Relay connector in Fuse Block No. 1.
Does the test light illuminate?
Yes → Go To 5
No → Go To 14

Remove and inspect Fuse #17 from Fuse Block No.1.
Is the fuse open?
Yes → Go To 6
No → Go To 8

Disconnect the Boost Pressure Solenoid harness connector.
Remove the Lift Pump Relay.
Install a good fuse in place of Fuse #17 in Fuse Block No.1
Remove and inspect Fuse #17 in Fuse Block No. 1.
Is the fuse open?
Yes → Repair the Engine Control relay Output circuit for a short to
ground.
No → Go To 7
7 NOTE: A short circuit exists in one of the following: Lift Pump Relay, Starter All
Relay, EGR Valve, Boost Pressure Servo Motor or ECM.
View repair.
Yes → Using the Service Information wiring check the listed components
for short circuits. Replace the shorted component as necessary.
236

Remove and inspect Fuse #16 from Fuse Block No.1
Is the fuse open?
Yes → Go To 9
No → Go To 11

Install a good fuse in place of Fuse #16 in Fuse Block No.1
Remove and inspect Fuse #16 from Fuse Block No.1.
Is the fuse open?
Yes → Repair the Engine Control Relay Output circuit for a short to
ground.
No → Go To 10
10 The Fuel Injectors, Crankcase Heater, Water In Fuel Sensor and related circuits can All
cause Fuse #16 in Fuse Block No.1 to open. Use the Service Information Wiring
Diagrams and check these circuits/components for shorted circuits.
Were any problems found.
Yes → Repair or replace shorted circuit/component as necessary.

Information.

Test Complete.

Repair the Engine Control Relay Output circuit(s) for an open.

Go To 12
237

Substitute the Engine Control Relay with a known good relay.
Yes → Replace the initial Engine Control Relay.

No → Go To 13

Remove the Engine Control Relay from Fuse Block No.1
Using a 12-volt test light connected to ground, check both Battery (+) circuits at the
Engine Control Relay connector in Fuse Block No.1
Yes → Repair the Engine Control Relay Output circuit for an open
between the Engine Control Relay connector in Fuse Block No. 1
and ECM C2 harness connector cavities 1, 3 and 5. It may be
necessary to replace the Fuse Block No. 1 to repair this circuit.
No → Repair the Battery (+) Supply circuits to the Engine Control
Relay.

Measure the resistance of the Engine Control Relay Control circuit.
Yes → Go To 15
No → Repair the Engine Control Relay Control circuit for an open.


Measure the voltage of the Engine Control Relay Control circuit.
Is the voltage below 1.0 volts?
Yes → Replace and program the ECM in accordance with the Service
Information.
No → Repair the Engine Control Relay Control circuit for a short to

voltage.
238
Symptom:
*ENGINE CRANKS BUT WILL NOT START
POSSIBLE CAUSES
CAMSHAFT POSITION SENSOR SIGNAL PROBLEM
CRANKSHAFT POSITION SENSOR SIGNAL PROBLEM
ECM CODES PRESENT
ECT SENSOR
ENGINE DRIVE GEAR/SPROCKET
FUEL SUPPLY CONTAMINATION
FUEL SYSTEM PRESSURE MECHANICAL
FUEL SYSTEM RESTRICTION
GLOW PLUGS
SKIM CODES PRESENT

1 NOTE: The ECM must have proper power and ground connections for the All
following tests to be valid. Refer to Checking the ECM Power and Grounds
in the symptom list.
NOTE: A no-start condition may occur if the Fuel Temperature Sensor is
shorted or if the Fuel Temperature Sensor Signal circuit is shorted to
ground or shorted to Sensor Ground.
Does the DRBIIIt display any ECM DTCs?
Yes → Refer to symptom list for problems related to ECM DTC.
Perform NO START VERIFICATION - VER-1.
No → Go To 2

With the DRBIIIt, read the SKREEM DTCs.
Does the DRBIIIt display any SKREEM DTCs?
Yes → Refer to symptom list for problems related to SKIM DTC.
No → Go To 3
3 Using a temperature probe, check the vehicle temperature near the ECT Sensor. All
With the DRBIIIt in Sensors, read the ECT Sensor temperature.
Compare the temperature probe reading with the DRBIIIt reading.
Are the two readings within 10°C of each other?
Yes → Go To 4
239
*ENGINE CRANKS BUT WILL NOT START — Continued

4 NOTE: Prior to performing this test, be sure to check the Glow Plug Relay All
operation. Refer to CHECKING GLOW PLUG OPERATION for the related
symptom(s).
Refer to the Service Information and check the Glow Plugs for proper operation.
Are the Glow Plugs operating properly?
Yes → Go To 5
5 Inspect the fuel system lines for restrictions, leaks or other problems. All
NOTE: Refer to the Service Information to ensure that the fuel system is
properly primed. An unprimed system or excessive air in the supply system
will cause a no-start condition.
Is there any evidence of problems?

No → Go To 6
6 Refer to the Service Information and perform the fuel pressure test. All
Is the fuel pressure within specification?
Yes → Go To 7
7 Inspect the fuel supply for contamination. All

Is the fuel contaminated?
Yes → Refer to the Service Information to remove and replace fuel
throughout the fuel system.
No → Go To 8

Using the DRBIIIt lab scope, backprobe the CMP Sensor Signal circuit at the ECM
harness connector.
while monitoring the DRBIIIt.
NOTE: Refer to Charts and Graphs to view a correct CMP Sensor signal.
Does the DRBIIIt display a steady clean CMP Signal pattern?
Yes → Go To 9
No → Perform Test for DTC P2043-Camshaft Position Sensor Circuit

Static Plausibility.
240
*ENGINE CRANKS BUT WILL NOT START — Continued

Using the DRBIIIt lab scope, backprobe both of the CKP Sensor Signal circuits at the
while monitoring the DRBIIIt.
Does the DRBIIIt display a steady clean CKP Signal pattern for each circuit?
Yes → Go To 10
No → Perform Test for DTC P2045-Crankshaft Position Sensor Circuit

Dynamic Plausibility.

241
Symptom:
*ENGINE WILL NOT CRANK
POSSIBLE CAUSES
BATTERY CABLE HIGH RESISTANCE
BATTERY CABLES
CHECKING FOR TCM CODES
ECM
ECM CODES PRESENT
IGNITION SWITCH OUTPUT (START) CIRCUIT OPEN
MECHANICAL PROBLEM
SKREEM CODES PRESENT
STARTER MOTOR
STARTER MOTOR RELAY
STARTER MOTOR RELAY CIRCUIT(S) OPEN
STARTER MOTOR RELAY CIRCUIT(S) SHORTED TO GROUND
STARTER RELAY CONTROL CIRCUIT SHORTED TO VOLTAGE
STARTER RELAY OUTPUT CIRCUIT OPEN

NOTE: The battery must be fully charged before diagnosing a no crank
condition.
Inspect the battery cables for corrosion, looseness or other problems.
Is there evidence of problems?
No → Go To 2

Remove the Starter Motor Relay from the Fuse/Relay Block.
Connect a test light between cavities 85 and 86 of the Starter Motor Relay connector
in the Fuse/Relay Block connector.
While observing the test light, attempt to start the engine.
Did the test light illuminate when turning the ignition switch to the Crank position?
Yes → Go To 3
No → Go To 8
242
*ENGINE WILL NOT CRANK — Continued

Using a 12-volt test light connected to ground, check the Ignition Switch Output
(Start) circuit in the Starter Motor Relay connector in the Fuse/Relay Block while
turning the ignition to the Crank/Start position.
Did the test light illuminate while turning the ignition to the Crank/Start position?
Yes → Go To 4
No → Repair the Ignition Switch Output (Start) circuit for an open.


Install a substitute relay in place of the Starter Motor Relay.
Does the engine crank?
Yes → Replace the Starter Motor Relay.
No → Go To 5

Disconnect the Starter Motor Relay Output wire from the Starter Solenoid.
Connect the Starter Motor Relay Output wire (at the Starter) to ground.
Using a 12-volt test light connected to 12-volts, check the Starter Motor Relay Output
circuit at the Starter Motor Relay connector in the Fuse/Relay Block.
Yes → Go To 6
No → Repair the Starter Relay Output circuit for an open.
6 Using the Service Information, check the battery cables for high resistance. All
Did either battery cable have a voltage drop greater than 0.2 volts?
Yes → Replace the battery cable(s).
No → Go To 7

Attempt to manually rotate the crankshaft 360°.
Is the crankshaft able to rotate 360°?
Yes → Replace the Starter Motor.
No → Repair the engine mechanical problem.
243

8 NOTE: The ECM must have proper power and ground connections for the All
following tests to be valid. Refer to Checking the ECM Power and Grounds
in the symptom list.
Does the DRBIIIt display any ECM DTCs?
Yes → Refer to symptom list for problems related to ECM DTC.
No → Go To 9

With the DRBIIIt, read the SKREEM DTCs.
Does the DRBIIIt display any SKREEM DTCs?
Yes → Refer to symptom list for problems related to SKREEM.

No → Go To 10

With the DRBIIIt, read the TCM DTCs.
Does the DRBIIIt display any TCM DTCs?
Yes → Refer to symptom list for problems related to TCM.

No → Go To 11
11 Perform the Checking the ECM Power and Grounds test. All
No → Go To 12

Remove the Starter Motor Relay from the Fuse/Relay Block
Remove the Engine Control Relay from the Fuse Block No.1.
Using a jumper wire, connect Engine Control Relay connector cavities 30 and 87 in
the Fuse Block No.1.
Measure the voltage of the Starter Motor Relay Control circuit.
Yes → Repair the Starter Relay Control circuit for a short to voltage.
No → Go To 13
244

Measure the resistance of the Starter Motor Relay Control circuit between the ECM
harness connector and the Fuse/Relay Block connector.
Measure the resistance of the Starter Motor Relay 12-volt Supply circuit between the
ECM harness connector and the Fuse/Relay Block connector.
Yes → Go To 14
No → Repair the Starter Motor Relay circuit(s) for an open.

Measure the resistance between ground and the Starter Motor Relay Control circuit
at the Fuse/Relay Block connector.
Measure the resistance between ground and the Starter Motor Relay 12-volt Supply
circuit at the Fuse/Relay Block connector.
No → Repair the Starter Motor Relay circuit(s) for a short to ground.
245
VERIFICATION TESTS
Verification Tests
BODY VERIFICATION TEST - VER 1 APPLICABILITY
1. Disconnect all jumper wires and reconnect all previously disconnected components and All
connectors.
2. Ensure that all accessories are turned off and the battery is fully charged.
3. NOTE: Refer to the service information for proper programming procedures if the
ABM; ACM; ATC; CTM; ECM; IC; SKREEM; SLA; or SSM was replaced.
4. If the SKREEM was replaced, program all RKE transmitters used with this vehicle.
5. NOTE: Perform the next 8 steps of this procedure if either diagnosing the
Automatic Temperature Control (ATC) system or if repairs were made to the ATC
system. All of the following criteria must be met in order to successfully run the ATC
Function Test.
6. With DRBIIIt, record and erase ATC DTCs.
7. Place the shift lever in Park.
8. Start the engine. Allow the engine to reach normal operating temperature.
9. Set the blower to high speed.
10. Press the Air Conditioning switch On.
11. With the DRBIIIt, verify that the ambient temperature is above 59°F (15°C), the refrigerant
pressure is between 29 and 348 PSI (2 and 24 bar), the evaporator temperature is above 36.5°F
(2.5°C), and the coolant temperature is above 158°F (70°C).
12. With the DRBIIIt in ATC, select System Tests and select ATC Function Test. When the ATC
Function Test is complete, proceed to the next step of this procedure.
13. With the DRBIIIt, read active ATC DTCs. If any DTC is active or if the original condition
is still present, proceed to the conclusion question and answer Yes.
14. With the DRBIIIt, record and erase all DTCs from ALL modules. Start and run the engine
for 2 minutes. Operate all functions of the system that caused the original concern.
15. Turn the ignition off and wait 5 seconds. Turn the ignition on and using the DRBIIIt, read
DTCs from ALL modules.
Are any DTC’s present or is the original condition still present?
Yes → Repair is not complete, refer to the appropriate symptom.
No → Repair is complete.
NAG1 TRANSMISSION VERIFICATION TEST - VER 1 APPLICABILITY

1. Reconnect any disconnected components. All
2. Connect the DRBIIIt to the Data Link Connector.
3. With the DRBIIIt, erase ABS DTCs.
4. With the DRBIIIt, erase ECM DTCs.
5. With the DRBIIIt, erase Transmission DTCs.
6. With the DRBIIIt, display Transmission Temperature. Start and run the engine until the
Transmission Temperature is HOT, above 43° C (110° F).
7. Check the Transmission fluid and adjust if necessary. Refer to the Service Information for the
proper Fluid Fill procedure.
8. NOTE: If internal repairs were performed and the shift quality is still poor, it may
be necessary to check the internal repair. Also check for any TSBs and/or Controller
Flash updates that may apply.
9. ROAD TEST PROCEDURE
10. Road test the vehicle. Make fifteen to twenty 1-2, 2-3, 3-4 and 4-5 upshifts.
11. Perform these shifts from a standing start to 72 km/h (45 MPH) with a constant throttle
opening of 20 to 25 degrees.
12. With speeds below 40 km/h (25 MPH), make five to eight wide open throttle kickdowns to
1st gear. Allow at least 5 seconds each in 2nd and 3rd gear between each kickdown.
13. With the DRBIIIt, read Transmission DTCs.
Were there any Diagnostic Trouble Codes set?
Yes → Repair is not complete, refer to appropriate symptom.
246
VERIFICATION TESTS
Verification Tests — Continued
NO START VERIFICATION - VER-1 APPLICABILITY

1. NOTE: IMPORTANT! If the Engine Control Module or Sentry Key Immobilizer All
Module has been replaced, ensure the programming procedure for the module has
been performed in accordance with the Service Information.
2. Inspect the vehicle to ensure that all engine components are properly installed and
connected. Reassemble and reconnect components as necessary.
3. Inspect the engine oil for contamination. If it is contaminated, change the oil and filter.
4. With the DRB, erase all diagnostic trouble codes (DTCs).
5. Turn the ignition off for at least 10 seconds.
6. Attempt to start the engine.
7. If the engine is unable to start, look for any Technical Service Bulletins (TSBs) that may
relate to this condition. Return to the Symptom List if necessary.
8. If the engine starts and continues to run, the repair is now complete.
Are any DTCs or symptoms remaining?
ROAD TEST VERIFICATION - VER-2 APPLICABILITY

1. Inspect the vehicle to ensure that all engine components are properly installed and All
connected. Reassemble and reconnect components as necessary.
2. If this verification procedure is being performed after a non-DTC test, perform steps 3 and
4. If not, proceed to step 5.
3. Check to see if the initial symptom still exists. If there are no trouble codes and the symptom
no longer exists, the repair was successful and testing is now complete.
4. If the initial or another symptom exists, the repair is not complete. Check all pertinent
Technical Service Bulletins (TSBs) and return to the Symptom List if necessary.
5. For previously read DTCs that have not been dealt with, return to the Symptom List and
follow the diagnostic path for that DTC; otherwise, continue.
6. If the Engine Control Module (ECM) has not been changed, perform steps 7 and 8, otherwise,
continue with step 9.
7. With the DRB IIIt, erase all diagnostic trouble codes (DTCs), then disconnect the DRB IIIt.
8. Turn the ignition off for at least 10 seconds.
9. If equipped with a Transfer Case Position Switch, perform step 10, otherwise, continue with
step 11.
10. With the ignition switch on, place the Transfer Case Shift Lever in each gear position,
stopping for 15 seconds in each position.
11. Ensure no DTCs remain by performing steps 12 through 15.
12. Road test the vehicle. For some of the road test, go at least 64 km/h (40 MPH). If this test
is for an A/C Relay Control Circuit, drive the vehicle for at least 5 minutes with the A/C on.
13. At some point, stop the vehicle and turn the engine off for at least 10 seconds, then restart
the engine and continue.
14. Upon completion of the road test, turn the engine off and check for DTCs with the DRB IIIt.
15. If the repaired DTC has set again, the repair is not complete. Check for any pertinent
Technical Service Bulletins (TSBs) and return to the Symptom List. If there are no DTCs, the
repair was successful and is now complete.
Are any DTCs or symptoms remaining?
247
NOTES
248
COMPONENT LOCATIONS
C
8.0 COMPONENT LOCATIONS O
M
8.1 CONTROL MODULES P
O
N
E
N
T
L
O
C
A
T
I
O
N
S
8.2 CONTROLS AND SOLENOIDS
249
COMPONENT LOCATIONS
C
O 8.2 CONTROLS AND SOLENOIDS (Continued)
M
P
O
N
E
N
T
L
O
C
A
T
I
O
N
S
8.3 DATA LINK CONNECTOR
250
COMPONENT LOCATIONS
C
8.4 SENSORS O
M
P
O
N
E
N
T
L
O
C
A
T
I
O
N
S
251
COMPONENT LOCATIONS
C
O 8.4 SENSORS (Continued)
M
P
O
N
E
N
T
L
O
C
A
T
I
O
N
S
252
COMPONENT LOCATIONS
C
8.5 SWITCHES O
M
P
O
N
E
N
T
L
O
C
A
T
I
O
N
S
253
NOTES
254
CONNECTOR PINOUTS
9.0 CONNECTOR PINOUTS
ACCELERATOR PEDAL POSITION SENSOR (OBD)

CAV CIRCUIT FUNCTION
1 18BL/DG ACCEL PEDAL POSITION SENSOR SIGNAL NO. 1
2 18BR/GY ACCEL PEDAL POSITION SENSOR GROUND NO. 2
3 18GY/DG ACCEL PEDAL POSITION SENSOR SIGNAL NO. 2
4 18BL/RD ACCEL PEDAL POSITION SENSOR 5 VOLT SUPPLY
5 18BR/BL ACCEL PEDAL POSITION SENSOR GROUND NO. 1
AIRBAG CONTROL MODULE - YELLOW

1 20BL DRIVER SEAT BELT TENSIONER LINE 2
2 20BR/YL DRIVER SEAT BELT TENSIONER LINE 1
3 20BL PASSENGER SEAT BELT TENSIONER LINE 2
4 20BR PASSENGER SEAT BELT TENSIONER LINE 1
5 20BK FUSED IGNITION SWITCH OUTPUT (RUN-START)
6 20BR GROUND
7 20YL AIRBAG WARNING INDICATOR DRIVER
8 - -
C
9 20BK/RD K-ACM
O
10 20DG DRIVER AIRBAG SQUIB 1 LINE 2
N
11 20VT DRIVER AIRBAG SQUIB 1 LINE 1
N
12 - -
E
13 20BL/DG PASSENGER AIRBAG SQUIB 1 LINE 2
C
14 20BR/DG PASSENGER AIRBAG SQUIB 1 LINE 1
T
15 - -
O
16 - -
R
17 - -
18 - -
P
19 - -
I
20 20DG ENHANCED ACCIDENT REPORT DRIVER
N
21 -
O
22 -
U
23 -
T
24 -
S
25 -
BOOST PRESSURE SENSOR (OBD)

1 18BR/WT SENSOR GROUND
2 18WT/DG BOOST PRESSURE SENSOR SIGNAL
3 18WT/RD BOOST PRESSURE SENSOR 5 VOLT SUPPLY
255
CONNECTOR PINOUTS
BOOST PRESSURE SERVOMOTOR (OBD)

1 16YL/BK FUSED ENGINE CONTROL RELAY OUTPUT
2 16YL/WT GROUND
3 - -
4 16YL/DG BOOST PRESSURE SERVOMOTOR CONTROL
5 - -
CAMSHAFT POSITION SENSOR - BLACK

1 20BR/DG CAMSHAFT POSITION SENSOR GROUND
2 20YL/GY CAMSHAFT POSITION SENSOR SIGNAL
3 18RD/BL (EXCEPT OBD) CAMSHAFT POSITION SENSOR 12 VOLT SUPPLY
3 20RD/BL (OBD) CAMSHAFT POSITION SENSOR 5 VOLT SUPPLY
C
O
N
N
E
C
T
O
R
P
I
N
O
U
T
S
256
CONNECTOR PINOUTS
CONTROLLER ANTILOCK BRAKE
1 12BR GROUND
2 12RD FUSED B(+)
3 - -
4 - -
5 14BR GROUND
6 14RD FUSED B(+)
7 - -
8 20BK/DG SENSOR SIGNAL
9 20YL/WT SENSOR SIGNAL
10 20YL/RD SENSOR SIGNAL
11 18BL/BK K-ABS/SHIFTER ASSEMBLY
12 18BK LEFT FRONT WHEEL SPEED SENSOR (+)
13 - -
14 20WT LEFT REAR WHEEL SPEED SENSOR (+)
15 18BR RIGHT FRONT WHEEL SPEED SENSOR (-)
16 18BK RIGHT FRONT WHEEL SPEED SENSOR (+)
17 - -
18 - -
19 - -
20 20WT BRAKE SWITCH OUTPUT C
21 20BR GROUND O
22 - - N
23 18BK/RD FUSED OPTIONAL EQUIPMENT RELAY OUTPUT N
24 20DG/WT CAN C BUS (+) E
25 20BR SENSOR GROUND C
26 20WT/GY BRAKE PRESSURE SENSOR SIGNAL T
27 18BK/BL TCS SWITCH (ASR) SENSE O
28 18BR LEFT FRONT WHEEL SPEED SENSOR (-) R
29 20BR LEFT REAR WHEEL SPEED SENSOR (-)
30 20BR RIGHT REAR WHEEL SPEED SENSOR (-) P
31 20YL RIGHT REAR WHEEL SPEED SENSOR (+) I
32 18BK/RD BRAKE LAMP SWITCH OUTPUT N
33 - - O
34 - - U
35 - - T
36 - - S
37 - -
38 - -
39 20RD/BL POWER INPUT
40 20DG CAN C BUS (-)
41 20DG/YL SENSOR SIGNAL
42 20WT/RD 5 VOLT SUPPLY
CRANKCASE HEATER - BLACK

1 18BR (EXCEPT OBD) GROUND
1 18BK/RD (OBD) CRANKCASE HEATER SIGNAL
2 16BK/RD (EXCEPT OBD) FUSED ENGINE CONTROL RELAY OUTPUT
2 18BK/BR (OBD) CRANKCASE HEATER GROUND
257
CONNECTOR PINOUTS
CRANKSHAFT POSITION SENSOR - BLACK

1 20DG (EXCEPT OBD) CRANKSHAFT POSITION SENSOR SIGNAL NO. 2
1 20DG/WT (OBD) CRANKSHAFT POSITION SENSOR SIGNAL NO. 1
2 20DG/WT (EXCEPT OBD) CRANKSHAFT POSITION SENSOR SIGNAL NO. 1
2 20DG (OBD) CRANKSHAFT POSITION SENSOR SIGNAL NO. 2
DATA LINK CONNECTOR - BLACK

1 20WT/DG K-SKREEM
2 - -
3 20DG/YL ENGINE RPM
4 20BR GROUND
5 20BR GROUND
6 - -
7 20BL/YL K-ECM
C 8 20BK/BL/DG FUSED IGNITION SWITCH OUTPUT (RUN-START)
O 9 20BL/BK K-ABS/SHIFTER ASSEMBLY
N 10 - -
N 11 20BL K-TCM/RADIO
E 12 20GY/DG/RD K-CTM/SSM
C 13 20BK/RD K-ACM
T 14 - -
O 15 20WT/GY K-IC/ATC/HBM/CHM
R 16 20RD/YL FUSED B(+)
P
I EGR VALVE - BLACK
N CAV CIRCUIT FUNCTION
O 1 20RD/YL (EXCEPT OBD) EGR VALVE CONTROL
U 1 20DG/WT (OBD) EGR VALVE CONTROL
T 2 16BK/GY (EXCEPT OBD) FUSED ENGINE CONTROL RELAY OUTPUT
S 2 16BK/DG (OBD) FUSED ENGINE CONTROL RELAY OUTPUT

3 18BR/BK (EXCEPT OBD) SENSOR GROUND
3 20BR/DG (OBD) SENSOR GROUND
4 - -
258
CONNECTOR PINOUTS
ENGINE CONTROL MODULE C1 (OBD)
1 16BL FUEL INJECTOR NO. 1 HIGH-SIDE CONTROL
2 16BL/WT FUEL INJECTOR NO. 4 HIGH-SIDE CONTROL
3 16DG FUEL INJECTOR NO. 3 HIGH-SIDE CONTROL
4 20RD/WT FUEL PRESSURE SOLENOID 12 VOLT SUPPLY
8 18BL/GY FUEL TEMPERATURE SENSOR SIGNAL
10 20RD/YL ENGINE OIL SENSOR 5 VOLT SUPPLY
11 20GY/BL ENGINE OIL SENSOR SIGNAL
12 20BR/RD INTAKE PRESSURE SENSOR GROUND
13 20VT/DG INTAKE PRESSURE SENSOR SIGNAL
14 20BR/DG CAMSHAFT POSITION SENSOR GROUND
15 20DG/BK O2 1/1 PUMP CELL SIGNAL
20 18BK/YL WATER IN FUEL SENSOR SIGNAL
21 18BK/RD CRANKCASE HEATER SIGNAL
25 16BK FUEL INJECTOR NO. 2 HIGH-SIDE CONTROL
26 16BK/WT FUEL INJECTOR NO. 5 HIGH-SIDE CONTROL
28 18RD/BK FUEL QUANTITY SOLENOID 12 VOLT SUPPLY
31 20YL/BL MASS AIR FLOW SENSOR GROUND
32 18DG/BK FUEL TEMPERATURE SENSOR GROUND
35 20BR/BK SENSOR GROUND
36 20VT/RD INTAKE PRESSURE SENSOR 5 VOLT SUPPLY C
37 20RD/BL CAMSHAFT POSITION SENSOR 5 VOLT SUPPLY O
38 20YL/GY CAMSHAFT POSITION SENSOR SIGNAL N
39 20GY O2 1/1 SENSOR CELL SIGNAL N
40 20GY/WT O2 1/1 VIRTUAL GROUND E
49 16BK/VT FUEL INJECTOR NO. 4 LOW-SIDE CONTROL C
50 16BK/DG FUEL INJECTOR NO. 3 LOW-SIDE CONTROL T
51 16BK/YL FUEL INJECTOR NO. 5 LOW-SIDE CONTROL O
52 20BK/WT FUEL PRESSURE SOLENOID CONTROL R
55 18BR WATER IN FUEL SENSOR GROUND
56 20BR/WT ENGINE COOLANT TEMPERATURE SENSOR GROUND P
57 20DG/RD ENGINE COOLANT TEMPERATURE SENSOR SIGNAL I
59 20DG/VT FUEL PRESSURE SENSOR SIGNAL N
61 20BR/VT MASS AIR FLOW SENSOR 5 VOLT SUPPLY O
62 20DG/YL O2 1/1 PUMP CELL CONTROL U
72 20GY/BL O2 1/1 HEATER CONTROL T
73 16BK/RD FUEL INJECTOR NO. 1 LOW-SIDE CONTROL S
74 16BK/BL FUEL INJECTOR NO. 2 LOW-SIDE CONTROL
76 18BR/YL FUEL QUANTITY SOLENOID CONTROL
79 18BR/RD WATER IN FUEL SENSOR 12 VOLT SUPPLY
84 20BR/GY FUEL PRESSURE SENSOR GROUND
85 20YL/DG MASS AIR FLOW SENSOR SIGNAL
86 20RD/DG FUEL PRESSURE SENSOR 5 VOLT SUPPLY
87 20DG/WT CRANKSHAFT POSITION SENSOR SIGNAL NO. 1
88 20DG CRANKSHAFT POSITION SENSOR SIGNAL NO. 2
90 20DG/WT EGR VALVE CONTROL
91 18BK/BR CRANKCASE HEATER GROUND
93 16YL/DG BOOST PRESSURE SERVOMOTOR CONTROL
259
CONNECTOR PINOUTS
ENGINE CONTROL MODULE C2 (OBD)
1 16BK/RD FUSED ENGINE CONTROL RELAY OUTPUT
2 14BR GROUND
3 14BK/BL FUSED ENGINE CONTROL RELAY OUTPUT
4 14BR GROUND
5 14BK/BL FUSED ENGINE CONTROL RELAY OUTPUT
6 14BR GROUND
7 18RD S/C SWITCH 12 VOLT SUPPLY
8 18BR/WT HIGH IDLE ON SIGNAL
10 18WT/RD BOOST PRESSURE SENSOR 5 VOLT SUPPLY
11 18WT/DG BOOST PRESSURE SENSOR SIGNAL
12 18BR/WT SENSOR GROUND
13 18GY/DG ACCEL PEDAL POSITION SENSOR SIGNAL NO. 2
14 18BR/GY ACCEL PEDAL POSITION SENSOR GROUND NO. 2
17 18BR/DG KICKDOWN SWITCH SIGNAL
18 20DG/YL ENGINE RPM
24 18BL/RD ACCEL PEDAL POSITION SENSOR 5 VOLT SUPPLY
25 18BL/DG ACCEL PEDAL POSITION SENSOR SIGNAL NO. 1
26 18BR/BL ACCEL PEDAL POSITION SENSOR GROUND NO. 1
C 28 18BR/DG INTAKE AIR TEMPERATURE SENSOR GROUND
O 31 20BL/YL K-ECM
N 32 20DG ENHANCED ACCIDENT REPORT DRIVER
N 36 18VT IGNITION SWITCH OUTPUT (START)
E 37 18DG ACCEL/SET SIGNAL
C 38 18BK VERIFICATION SIGNAL
T 42 18DG/WT INTAKE AIR TEMPERATURE SENSOR SIGNAL
O 43 18BK/RD GLOW PLUG MODULE CONTROL
R 44 18YL/BL ENGINE CONTROL RELAY CONTROL

50 18YL DECEL/SET SIGNAL
P 51 18GY OFF SIGNAL
I 52 18BL RESUME SIGNAL
N 53 20DG/WT CAN C BUS (+)
O 54 20DG CAN C BUS (-)
U 55 18BR/RD FUEL PUMP RELAY CONTROL
T 58 18VT/DG STARTER MOTOR RELAY CONTROL
ENGINE COOLANT TEMPERATURE SENSOR - BLACK

1 20BR/WT ENGINE COOLANT TEMPERATURE SENSOR GROUND
2 20DG/RD ENGINE COOLANT TEMPERATURE SENSOR SIGNAL
260
CONNECTOR PINOUTS
ENGINE OIL SENSOR - BLACK

1 20GY/BL ENGINE OIL SENSOR SIGNAL
2 20BR/BK SENSOR GROUND
3 20RD/YL ENGINE OIL SENSOR 5 VOLT SUPPLY
FUEL INJECTOR NO. 1 - BLACK

1 14BK/BL (EXCEPT OBD) FUEL INJECTOR NO. 1 CONTROL
1 16BK/RD (OBD) FUEL INJECTOR NO. 1 LOW-SIDE CONTROL
2 14BK (EXCEPT OBD) COMMON INJECTOR DRIVER NO. 1
2 16BL (OBD) FUEL INJECTOR NO. 1 HIGH-SIDE CONTROL
C
O
N
N
E
C
FUEL INJECTOR NO. 2 - BLACK T
O
1 14BK/VT (EXCEPT OBD) FUEL INJECTOR NO. 2 CONTROL
R
1 16BK/BL (OBD) FUEL INJECTOR NO. 2 LOW-SIDE CONTROL
2 14BL (EXCEPT OBD) COMMON INJECTOR DRIVER NO. 2
P
2 16BK (OBD) FUEL INJECTOR NO. 2 HIGH-SIDE CONTROL
I
N
O
U
T
S

1 14BK/RD (EXCEPT OBD) FUEL INJECTOR NO. 3 CONTROL
1 16BK/DG (OBD) FUEL INJECTOR NO. 3 LOW-SIDE CONTROL
2 16DG (OBD) FUEL INJECTOR NO. 3 HIGH-SIDE CONTROL
261
CONNECTOR PINOUTS

1 14BK/YL (EXCEPT OBD) FUEL INJECTOR NO. 4 CONTROL
1 16BK/VT (OBD) FUEL INJECTOR NO. 4 LOW-SIDE CONTROL
2 16BL/WT (OBD) FUEL INJECTOR NO. 4 HIGH-SIDE CONTROL

1 14BK/DG (EXCEPT OBD) FUEL INJECTOR NO. 5 CONTROL
1 16BK/YL (OBD) FUEL INJECTOR NO. 5 LOW-SIDE CONTROL
2 14BL (EXCEPT OBD) COMMON INJECTOR DRIVER NO. 2
2 16BK/WT (OBD) FUEL INJECTOR NO. 5 HIGH-SIDE CONTROL
C
O
N
N
E
C
T FUEL PRESSURE SENSOR - BLACK
O CAV CIRCUIT FUNCTION
R 1 20BR/GY FUEL PRESSURE SENSOR GROUND
2 20DG/VT FUEL PRESSURE SENSOR SIGNAL
P 3 20RD/DG FUEL PRESSURE SENSOR 5 VOLT SUPPLY
I
N
O
U
T
S

1 20BK/WT FUEL PRESSURE SOLENOID CONTROL
2 20RD/WT FUEL PRESSURE SOLENOID 12 VOLT SUPPLY
FUEL PUMP (OBD)

1 14BK FUEL PUMP RELAY OUTPUT
2 14BR GROUND
262
CONNECTOR PINOUTS
FUEL PUMP RELAY (OBD)

30 14RD/BK FUSED B(+)
85 18BR/RD FUEL PUMP RELAY CONTROL
86 18BK/RD FUSED ENGINE CONTROL RELAY OUTPUT
87 14BK FUEL PUMP RELAY OUTPUT
87A - -
FUEL QUANTITY CONTROL VALVE (OBD)

1 20BK/WT FUEL QUANTITY SOLENOID CONTROL
2 18RD/BK FUEL QUANTITY SOLENOID 12 VOLT SUPPLY
C
O
N
N
1 18DG/BK FUEL TEMPERATURE SENSOR GROUND
E
2 18BL/GY FUEL TEMPERATURE SENSOR SIGNAL
C
T
O
R
P
I
N
O
U
T
S
263
CONNECTOR PINOUTS
C
O
N
N
E
C
T
O
R
P
I
N
O
U
T
S
264
CONNECTOR PINOUTS
ENGINE CONTROL RELAY (FUSE BLOCK NO. 1)
30 INTERNAL FUSED B(+)
85 INTERNAL ENGINE CONTROL RELAY CONTROL
86 INTERNAL FUSED B(+)
87 INTERNAL ENGINE CONTROL RELAY OUTPUT
87A - -
FUSES (FUSE BLOCK NO. 1)

FUSE AMPS FUSED CIRCUIT FUNCTION
NO.
1 - - -
2 10A 16WT FUSED HIGH BEAM SWITCH OUTPUT
3 10A 16WT FUSED HIGH BEAM SWITCH OUTPUT
4 10A 16WT/BL/RD FUSED IGNITION SWITCH OUTPUT (RUN-START)
5 10A 16BK/BL/WT FUSED IGNITION SWITCH OUTPUT (RUN-START)
6 20A INTERNAL FUSED IGNITION SWITCH OUTPUT (RUN-START)
7 15A 16BK/YL FUSED IGNITION SWITCH OUTPUT (RUN-START)
8 20A 16RD/YL FUSED B(+)
9 15A INTERNAL FUSED B(+)
10 10A 16GY/DG/RD HEADLAMP SWITCH OUTPUT
11 10A 16GY/BK FUSED LEFT LAMP RELAY OUTPUT
C
12 10A 18YL HEADLAMP SWITCH OUTPUT
O
13 10A 18YL HEADLAMP SWITCH OUTPUT
N
14 15A 16BK/YL/WT FOG LAMP RELAY SIGNAL
N
15 10A 16BK/RD FUSED IGNITION SWITCH OUTPUT (ACC-RUN-START)
E
16 15A 12BK/BL ENGINE CONTROL RELAY OUTPUT
C
17 15A 16BK/RD ENGINE CONTROL RELAY OUTPUT
T
18 15A 14BK FUSED IGNITION SWITCH OUTPUT (RUN-START)
O
19 15A 14RD/BK (OBD) FUSED B(+)
R
20 15A 16RD/BL FUSED B(+)
21 30A 12RD FUSED B(+)
P
I
N
O
U
T
S
265
CONNECTOR PINOUTS
C
O
N
N
E
C
T
O
R
P
I
N
O
U
T
S
266
CONNECTOR PINOUTS
FUSES (FUSE BLOCK NO. 2)
NO.
1 10A 16RD/GY FUSED B(+)
4 7.5A 16RD/YL FUSED B(+)
5 25A 14RD/WT FUSED B(+)
6 7.5A 18RD/YL FUSED B(+)
7 25A 16BK/YL OPTIONAL EQUIPMENT RELAY OUTPUT
8 10A 16BK/RD OPTIONAL EQUIPMENT RELAY OUTPUT
9 15A 16RD/YL/WT FUSED D+ RELAY NO. 1 OUTPUT
10 7.5A 16RD/YL/WT FUSED D+ RELAY NO. 1 OUTPUT
11 7.5A 16RD/YL/WT FUSED D+ RELAY NO. 1 OUTPUT
15 25A 16BK/YL/DG OPTIONAL EQUIPMENT RELAY OUTPUT
C
O
N
N
E
C
T
O
R
P
I
N
O
U
T
S
267
CONNECTOR PINOUTS
C
O
N
N
E
C
T
O
R
P
I
N
O
U
T
S
268
CONNECTOR PINOUTS
FUSES (FUSE/RELAY BLOCK)
NO.
1 30A 14BL/YL FUSED B(+)
2 - - -
3 - - -
4 - - -
5 10A 16RD/YL FUSED B(+)
6 7.5A 18BK/RD FUSED OPTIONAL EQUIPMENT RELAY OUTPUT
10 30A 12RD/GY FUSED B(+)
STARTER MOTOR RELAY (FUSE/RELAY BLOCK)

30 12BK/YL STARTER MOTOR RELAY OUTPUT
85 18VT/DG STARTER MOTOR RELAY CONTROL
86 18RD/BL (EXCEPT OBD) STARTER MOTOR RELAY 12 VOLT SUPPLY
86 18BK/RD (OBD) STARTER MOTOR RELAY 12 VOLT SUPPLY
87 12VT IGNITION SWITCH OUTPUT (START)
87A - -
C
O
N
N
E
C
T
O
R
P
I
N
O
U
T
S
269
CONNECTOR PINOUTS
GLOW PLUG CONTROL MODULE C1 - BLACK

1 18BR GROUND
2 18BK/RD GLOW PLUG MODULE CONTROL
3 - -
GLOW PLUG CONTROL MODULE C2 - BLACK

1 14BK/DG GLOW PLUG NO. 5 SUPPLY VOLTAGE
2 14BK/YL GLOW PLUG NO. 4 SUPPLY VOLTAGE
3 14BK/RD GLOW PLUG NO. 3 SUPPLY VOLTAGE
C 4 14BK/VT GLOW PLUG NO. 2 SUPPLY VOLTAGE
O 5 14BK/BL GLOW PLUG NO. 1 SUPPLY VOLTAGE
N 6 - -
N
E
C
T
O
R
P INTAKE AIR PRESSURE SENSOR (OBD)

I CAV CIRCUIT FUNCTION
N 1 20BR/RD INTAKE PRESSURE SENSOR GROUND
O 2 20VT/DG INTAKE PRESSURE SENSOR SIGNAL
U 3 20VT/RD INTAKE PRESSURE SENSOR 5 VOLT SUPPLY
T
S
INTAKE AIR TEMPERATURE SENSOR - BLACK

1 18BR/DG INTAKE AIR TEMPERATURE SENSOR GROUND
2 18DG/WT INTAKE AIR TEMPERATURE SENSOR SIGNAL
270
CONNECTOR PINOUTS
KICK DOWN SWITCH - BLACK

1 18BR/DG KICKDOWN SWITCH SIGNAL
2 18BR (EXCEPT OBD) SENSOR GROUND
2 18BR (OBD) GROUND
MASS AIR FLOW SENSOR - BLACK

1 16YL/RD (OBD) FUSED IGNITION SWITCH OUTPUT (RUN-START)
2 20YL/RD (EXCEPT OBD) MASS AIR FLOW SENSOR 12 VOLT SUPPLY
2 20BR/VT (OBD) MASS AIR FLOW SENSOR 5 VOLT SUPPLY
3 20BR/YL (EXCEPT OBD) MASS AIR FLOW SENSOR GROUND
3 20YL/BL (OBD) MASS AIR FLOW SENSOR GROUND
4 20BR/BK (EXCEPT OBD) MASS AIR FLOW SENSOR 5 VOLT SUPPLY
4 20YL/DG (OBD) MASS AIR FLOW SENSOR SIGNAL
5 20YL/DG (EXCEPT OBD) MASS AIR FLOW SENSOR SIGNAL
C
O
N
N
OXYGEN SENSOR (OBD) E
CAV CIRCUIT FUNCTION C
1 20DG/BK O2 1/1 PUMP CELL SIGNAL T
2 20GY/WT O2 1/1 VIRTUAL GROUND O
3 20GY/BL O2 1/1 HEATER CONTROL R
4 20RD/DG FUSED ENGINE CONTROL RELAY OUTPUT
5 20DG/YL O2 1/1 PUMP CELL CONTROL P
6 20GY O2 1/1 SENSOR CELL SIGNAL I
N
O
U
T
S
271
CONNECTOR PINOUTS
C
O
N
N
E
C
T
O
R
P
I
N
O
U
T
S
272
CONNECTOR PINOUTS
FUSED IGNITION SWITCH RUN-START RELAY (RELAY BLOCK)
30 14RD FUSED B(+)
86 16BR GROUND
87 14BK/YL FUSED IGNITION SWITCH RUN-START RELAY OUTPUT
87A - -
SPEED CONTROL SWITCH

1 18GY OFF SIGNAL
2 18BK VERIFICATION SIGNAL
3 18BL RESUME SIGNAL
4 18YL DECEL/SET SIGNAL
5 18DG ACCEL/SET SIGNAL
6 18RD S/C SWITCH 12 VOLT SUPPLY
WATER IN FUEL SENSOR - BLACK C

CAV CIRCUIT FUNCTION O
1 18BR WATER IN FUEL SENSOR GROUND N
2 18BR/RD WATER IN FUEL SENSOR 12 VOLT SUPPLY N
3 18BK/YL WATER IN FUEL SENSOR SIGNAL E
C
T
O
R
P
I
N
O
U
T
S
273
NOTES
274
SCHEMATIC DIAGRAMS
10.0 SCHEMATIC DIAGRAMS
10.1 ENGINE CONTROL MODULE
S
C
H
E
M
A
T
I
C
D
I
A
G
R
A
M
S
275
SCHEMATIC DIAGRAMS
10.2 ENGINE CONTROL MODULE
S
C
H
E
M
A
T
I
C
D
I
A
G
R
A
M
S
276
CHARTS AND GRAPHS
11.0 CHARTS AND GRAPHS C
H
A
R
T
S
A
N
D
G
R
A
P
H
S
277
NOTES
278
DIAGNOSTIC TEST PROCEDURES — TELL US!
DaimlerChrysler Corporation is constantly working to provide the technician the best diagnostic manuals possible.
Your comments and recommendations regarding the diagnostic manuals and procedures are appreciated.
To best understand your suggestion, please complete the form giving us as much detail as possible.
Model Year Body Type Engine
Transmission Vehicle Mileage MDH
Diagnostic Procedure Book No. Page
Comments/recommendations (if necessary, draw sketch)
Name
Submitted by:
Address
City/State/Zip
Business Phone #
All comments become property of DaimlerChrysler Corporation and may be used without compensation.
Dealer Technical Operations
800 Chrysler Drive
CIMS 486-02-76
Auburn Hills, MI 48326-2757

2004-2006-VA-Powertrain

Uploaded by

Copyright:

Available Formats

2004-2006-VA-Powertrain

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

2004-2006-VA-Powertrain

Uploaded by

Copyright:

Available Formats

TABLE OF CONTENTS

1.1 SYSTEM COVERAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

2.0 IDENTIFICATION OF SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

3.0 SYSTEM DESCRIPTION AND FUNCTIONAL OPERATION . . . . . . . . . . . . . . . . . . . . . .1

3.1 GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

4.0 DISCLAIMERS, SAFETY, WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

5.0 REQUIRED TOOLS AND EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

6.0 GLOSSARY OF TERMS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

7.0 DIAGNOSTIC INFORMATION AND PROCEDURES . . . . . . . . . . . . . . . . . . . . . . . . . . .11

8.0 COMPONENT LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .249

8.1 CONTROL MODULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .249

9.0 CONNECTOR PINOUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .255

ACCELERATOR PEDAL POSITION SENSOR (OBD) . . . . . . . . . . . . . . . . . . . . . . . . .255

10.0 SCHEMATIC DIAGRAMS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .275

10.1 ENGINE CONTROL MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .275

11.0 CHARTS AND GRAPHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .277

Ignition Switch On (Engine Off) After-Run Mode

3.3 DIAGNOSTIC TROUBLE CODES 3.3.3 ECM DIAGNOSTIC TROUBLE CODES

3.4 USING THE DRBIIIT 4.2 SAFETY

TEST ACTION APPLICABILITY

Yes → Refer to the wiring diagrams located in the service information to

2 Turn the ignition off. All

Yes → Repair the K-ECM circuit for a short to ground.

3 Turn the ignition off. All

Yes → Repair the K-ECM circuit for a short to voltage.

*NO RESPONSE FROM ENGINE CONTROL MODULE — Continued

TEST ACTION APPLICABILITY

TEST ACTION APPLICABILITY

Yes → Refer to the wiring diagrams located in the service information to

2 Turn the ignition off. All

Yes → Repair the K-SKREEM circuit for a short to ground.

3 Turn the ignition off. All

Yes → Repair the K-SKREEM circuit for a short to voltage.

*NO RESPONSE FROM SENTRY KEY REMOTE ENTRY MODULE —

P-1105 ATMOSPHERIC PRESSURE SENSOR PLAUSIBILITY WITH

When Monitored and Set Condition:

P1105-ATMOSPHERIC PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH

P1105-ATMOSPHERIC PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW

P2500-FUEL PRESSURE SOLENOID CIRCUIT EXCESSIVE CURRENT

P-1105 ATMOSPHERIC PRESSURE SENSOR PLAUSIBILITY WITH

Yes → Replace and program the Engine Control Module in accordance

2 WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A All

Yes → Repair as necessary.

When Monitored and Set Condition:

P0100-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW

P0100-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW

P2011-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO HIGH

P2011-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO LOW

P0100-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW —

P2024-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO HIGH

P2024-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW

P2067-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO HIGH

P2067-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW

P2068-MASS AIR FLOW SENSOR PLAUSIBILITY SIGNAL RATIO ERROR

P0100-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW —

3 Turn the ignition off. All

P0100-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW —

6 Turn the ignition off. All

7 Turn the ignition off. All

8 Turn the ignition off. All