Ecodial Advance Calculation

Technical help
Ecodial AC 4

Contents
Component names
Main changes following the Cenelec TR50480 report
Types of system earthing
Types of transformer losses
Diversity factor Ks
Switchgear status and operating modes
Discrimination of LV protective devices
Check on the thermal stress in cables
Discrimination of residual-current protective devices
Discrimination between MV and LV protective devices
Cascading
Withdrawable circuit breakers and switches
Electrical operating mechanisms for circuit breakers and switches
Remote opening of switches
Visible break
Classification of residual current devices
Type of residual-current protection
High-sensitivity residual-current protection
Medium-sensitivity residual-current protection
Maximum permissible voltage drop for loads
Circuit voltage-drop tolerances
Cable installation method
Maximum, permissible cross-sectional area
Cable sizing according to circuit breaker setting or rating
Number of additional touching circuits
Third-order harmonic distortion
Manual and alternate solutions
Additional derating coefficients for wiring systems
Waiver of overload-protection requirements for safety circuits
Power factor for short-circuits on LV sources
Calculation of LV-source phase impedances, based on Ik3max
Calculation of LV-source neutral impedances, based on Ik1min
Calculation of LV-source PE impedances, based on Ief
Calculation of LV-source PE impedances, based on Ief2min
Consistency of LV-source input parameters
Type of regulation of LV capacitor banks
Types of LV capacitor banks
Reactive power threshold
Technical help Page 2/61
Ecodial AC 4

Coordination of circuit breakers and contactors

Trip classes of motor thermal protection
Motor inrush currents
Transient over-torque of variable speed drives
Single-pole breaking capacity at phase-to-phase voltage on IT systems
Single-pole breaking capacity at phase-to-neutral voltage on TN systems
Feeder distribution for Busbar Trunking System (BTS)
Distance from origin
MV protective device
MV fuse technology
Type of MV relay
Time dependent tripping curves for MV digital relay
UPS inputs connection
UPS requested redundancy
UPS mode
UPS transformer requested
Number of UPS
Number of UPS for redundancy
Number of bypass
Battery backup time

Technical help Page 3/61

Ecodial AC 4

Component names
The default prefix of component names is defined in accordance with standard IEC 81346-2.
This standard defines the following rules depending on the type of equipment.

Code IEC 81346-2 definition Examples Ecodial component

Transporting low voltage LV cable and feeder
electrical energy( ≤ 1 000 V a.c. busbar-trunking
WD or ≤ 1 500 V d.c.) Bushing, cable, conductor systems (BTS)
Distributing low voltage
electrical energy( ≤ 1 000 V a.c. Busbar, motor control centre, Busbars and busbar-
WC or ≤ 1 500 V d.c.) switchgear assembly trunking systems (BTS)
Enclosing and supporting
UC electrical energy equipment Cubicle, encapsulation, housing LV switchboards
Converting electrical energy AC/DC converter, frequency
while retaining the energy type converter, power transformer, MV/LV and LV/LV
TA and energy form transformer transformers
Switching and variation of Circuit-breaker, contactor, motor Circuit-breakers and
QA electrical energy circuits starter, power transistor, thyristor contactors
Disconnector, fuse switch, fuse-
Isolation of electrical energy switch disconnector, isolating Switches and fuse
QB circuits switch, load-break switch switches
Driving by electromagnetic
MA force Electric motor, linear motor Asynchronous motors
Initiation of an electrical energy Dynamo, generator, motor-
flow by use of mechanical generator set, power generator,
GA energy rotating generator Emergency generators
Fluorescent lamp, fluorescent
Generation of electromagnetic tube, incandescent lamp, lamp,
radiation for lighting purposes lamp bulb, laser, LED lamp,
EA using electrical energy maser, UV radiator Lighting loads
Capacitive storage of electric
CA energy Capacitor Capacitors
Stabilizing a flow of electrical Uninterruptible power supply
RB energy (UPS) UPS

Technical help Page 4/61

Ecodial AC 4

Main changes following the Cenelec TR50480 report

Modification of voltage factor c
Table 7 in the Cenelec TR50480 technical report is derived from Table 1 in the IEC 60909 standard.

Rated voltage Voltage factor

cmax cmin
100 V to 1000 V 1.1 0.95

Elimination of the no-load factor m

The no-load factor m, present in the Cenelec R064-003 technical report, has been eliminated from all
equations in the Cenelec TR50480 technical report.

Calculation of short-circuit currents with parallel-connected transformers

The Cenelec TR50480 technical report defines more precisely the impedance method for calculation of
short-circuit currents in installations supplied by parallel-connected transformers.

Generator supply LV supply MV supply + parallel-connected MV/LV transformers

ZG ZQ ZQ
ZSUP ZSUP ZSUP
ZC ZC ZC

ZT

      Incomer:   
ZSUP = ZC + ZG ZSUP = Z Q + Z C     ZQ (ZT + ZC )
 ZQ ( ZT + ZC ) Outgoer: ZSUP =
ZSUP = nT
nT − 1
nT is the total number of transformers operating
simultaneously.
Incomer = the conductor between the transformer and the
main switchboard.
Outgoer = the circuits supplying the entire installation
downstream of the main switchboard.

Contribution of asynchronous motors to short-circuit currents

The Cenelec TR50480 technical report defines the KM coefficient that must be applied to the impedances
(RSUP, XSUP) to take into account the contribution of the motors.
The table below sums up the conditions where the contribution of asynchronous motors to the short-
circuit current must be taken into account.

Type of supply Motor Total power rating of KM value

motors operating
simultaneously (SrM)
Supply via MV/LV
transformer(s)
No static converter > 25% total power rating
of transformers (SrT)
5⋅ ∑S rT

5⋅ ∑ SrT + 1,1 ⋅ SrM

Technical help Page 5/61

Ecodial AC 4

Types of system earthing

TN-S system

TN-C system

Not permitted on sites where

there is a risk of fire or
explosion.

TT system

IT system

Where possible, the neutral

is not distributed.

For more information: Electrical Installation Wiki.

Technical help Page 6/61

Ecodial AC 4

Types of transformer losses

Immersed-type transformers
Losses of MV/LV immersed-type transformers are defined by standard EN 50464-1 for:
losses under no-load conditions (P0),
losses under load conditions (Pk).
This classification is valid for transformers immersed in mineral and vegetable oil.

No-load losses (P0) Load losses (Pk)

Optimum efficiency Optimum efficiency

Standard efficiency Standard efficiency

Dry-type transformers
Dry-type encapsulated transformers offer two possible loss levels:
normal losses,
reduced losses.

Technical help Page 7/61

Ecodial AC 4

Diversity factor Ks
Standard IEC 61439-1 defines the diversity-factor (Ks) values that may be used if more precise
information on switchboards and busbar-trunking systems (BTS) is lacking.
Ecodial uses these values by default to calculate the design currents for BTSs and busbars.

Switchboard busbars
Number of outgoers Ks
1 1
2-3 0.9
4-5 0.8
6 to 9 0.7
10 and more 0.6

Distribution BTS
Number of outgoers Ks
1 1
2-3 0.9
4-5 0.8
6 to 9 0.7
10 to 40 0.6
Over 40 0.5

For more information: Electrical Installation Wiki.

Diversity factor and operating mode

For distribution BTSs and busbars, it is possible to set a diversity factor for each type of operating mode.
Simply select an operating mode and enter a value between 0 and 1 for the Ks parameter. The value
becomes the default value for the current operating mode (the lock next to the parameter closes ) and
Ecodial will no longer modify the value as a function of the number of outgoers. In the other operating
modes, the Ks value will continue to be calculated by Ecodial, unless the value is set as indicated above.

Technical help Page 8/61

Ecodial AC 4

Switchgear status and operating modes

This property determines the open/closed (off/on) position of circuit breakers and switches in the various
operating modes. Ecodial can manage different status conditions of switchgear depending on the
operating mode. This makes it possible to take into account installations supplied by multiple sources,
those offering load shedding and those with seasonal operating modes, for example.
When the status of a circuit breaker or switch is "closed",, the circuit downstream of the circuit breaker (or
switch) is supplied in the current operating mode.
When the status of a circuit breaker or switch is "open", the downstream circuit is not supplied in the
current operating mode.

When a part of the network is not supplied in a given operating mode, it is shown in blue in the single-line
diagram. Given that the "closed" status condition is the most common in installations, only the "open"
status condition is shown in the single-line diagram.

Technical help Page 9/61

Ecodial AC 4

Discrimination of LV protective devices

Principle
Instantaneous setting of the downstream protective device

Crossing detection zone. Table zone.

Discrimination limit = current at Check the manufacturer discrimination
which the curves cross. tables to determine the limit.

Tripping curve

Non-tripping curve

Partial and total discrimination

If the tripping curve of the downstream protection crosses the non-tripping curve of the upstream
protection, discrimination is said to be partial and the current at which the curves cross is called the
discrimination or selectivity limit current.

If the selectivity limit current is lower than the short-circuit current that can occur on the circuit protected
by the downstream protective device, discrimination is said to be partial.

If the selectivity limit current is higher than the maximum short-circuit current that can occur on the circuit
protected by the downstream protective device, discrimination is said to be total for the given installation.

Means to achieve total discrimination

If the curves cross in the crossing detection zone, i.e. below the downstream instantaneous-setting
current, the settings on the protective devices may be adjusted to achieve discrimination. Use of time-
delayed trip units makes this easier.

If the discrimination limit is in the table zone, the rating of the upstream protective device must be
increased. In this case, Ecodial retains the circuit design current Ib as the reference for the thermal
setting of the protective device to avoid oversizing the cable.

For more information: Electrical Installation Wiki.

Technical help Page 10/61

Ecodial AC 4

Check on the thermal stress in cables

Principle
Ecodial checks the thermal stress for all conductors in a cable:
phase,
neutral,
PE or PEN.
The thermal stress is within permissible limits if:
the Isd threshold is lower than the circuit minimum short-circuit current (IEC 60364 § 533.3.2).
Otherwise, Ecodial checks that:
the thermal stress (i²t) in each of the circuit conductors (phase, neutral, PE or PEN) in the cable
does not cross the t(i) curve of the protective device.

Ikmin

i²t phase

i²t neutral

i²t PE

Necessary measures if a cable is not protected against thermal stress

If neither of the above conditions are met, there are two ways to correct the circuit:
install an adjustable protective device on which Isd can be set to below Ikmin,
manually increase the cross-sectional area of the conductor(s) that are insufficiently protected by
the current protective device.

Technical help Page 11/61

Ecodial AC 4

Discrimination of residual-current protective devices

Principle
Discrimination between residual-current protective devices is achieved if the following conditions are met:
the sensitivity of the upstream device is greater than double the sensitivity of the downstream
device,
the breaking time of the upstream device is 1.4 times longer than that of the downstream device.

The sensitivity of the downstream device must also meet the condition below:
sensitivity (I∆n) x 2 ≤ fault current (Ief).

≥ 2 → current discrimination OK

I∆n x2 ≤ Ief → protection of persons OK

Ikmin

≥ 1.4 → time discrimination OK

Partial discrimination
When the sensitivity discrimination condition is not met, discrimination is said to be partial.

However if the breaking-time discrimination condition is not met, there is no discrimination between the
two residual-current protective devices (even if the sensitivity discrimination condition is met).

Technical help Page 12/61

Ecodial AC 4

Discrimination between MV and LV protective devices

To check discrimination between MV and LV protective devices, tripping curves have to be compared on
the same side of the transformer.
In Ecodial the MV protective device tripping curve is converted to the equivalent low voltage curve in
order to make the discrimination analysis.

Depending if the MV protective device is a fuse or relay the rules to ensure discrimination between MV
and LV are slightly different.

For MV fuse:
all parts of the minimum pre-arcing fuse curve must be located to the right of the CB curve by a
factor of 1.35 or more (e.g. where, at time T, the CB curve passes through a point corresponding
to 100 A, the fuse curve at the same time T must pass through a point corresponding to 135 A, or
more, and so on...),
and all parts of the fuse curve must be above the CB curve by a factor of 2 or more (e.g. where,
at a current level I the CB curve passes through a point corresponding to 1.5 seconds, the fuse
curve at the same current level I must pass through a point corresponding to 3 seconds, or more,
etc.).
The factors 1.35 and 2 are based on standard maximum manufacturing tolerances for MV fuses and LV
circuit-breakers.

For MV relays associated to MV circuit-breakers:

all parts of the minimum MV CB curve must be located to the right of the LV CB curve by a factor
of 1.35 or more (e.g. where, at time T, the LV CB curve passes through a point corresponding to
100 A, the MV CB curve at the same time T must pass through a point corresponding to 135 A, or
more, and so on...),
and all parts of the MV CB curve must be above the LV CB curve (time of LV CB curve must be
less or equal than MV CB curves minus 0.3 s).
The factors 1.35 and 0.3 s are based on standard maximum manufacturing tolerances for MV current
transformers, MV protection relay and LV circuit-breakers.

Where a LV fuse-switch is used, similar separation of the characteristic curves of the MV protective
device and LV fuses must be respected.

For more information: Electrical Installation Wiki.

Technical help Page 13/61

Ecodial AC 4

Cascading
Default and individual parameter settings
On the Project parameters tab, in the zone for device selection, it is possible to request that the system
attempt to set up cascading for all final protection devices, i.e. those immediately upstream of the loads. It
is on the final circuits that there is the greatest number of outgoers and consequently that cascading can
provide the greatest benefits.
In addition, there is an individual parameter for each circuit breaker in the installation, among the circuit-
breaker properties, to activate or deactivate system attempts to establish cascading.

Attempts to find a cascading solution

When cascading is requested for a circuit breaker, Ecodial looks for a cascading solution with the
upstream circuit breaker.
If Ecodial cannot find a cascading solution with the upstream circuit breaker, a warning message is
displayed in the alarm window and solutions without cascading are proposed.

Limits on cascading
Certain configurations in electrical installations making cascading impossible:
the circuit breaker selected for cascading is supplied by two parallel circuits,
the circuit breaker selected for cascading and the upstream circuit breaker are on opposite sides of a
LV/LV transformer.

Circuit breaker downstream of parallel Circuit breakers on opposite sides of an

MV/LV transformers LV/LV transformer

No cascading

No cascading

Other configurations for which cascading is not attempted

When a circuit breaker is supplied by circuit breakers operating under different operating modes, Ecodial
does not attempt to find a cascading solution.

No search for a
cascading solution

For more information: Electrical Installation Wiki.

Technical help Page 14/61

Ecodial AC 4

Withdrawable circuit breakers and switches

If a withdrawable circuit breaker or switch is required, Ecodial selects only devices that can be
disconnected from a chassis (withdrawable or drawout versions) or a base (plug-in versions), i.e.
withdrawability not dependent on the switchboard system in which they are installed.

If withdrawability is not required, Ecodial proposes solutions without taking the feature into account.

In the results zone, Ecodial indicates whether a withdrawable version exists for each device.

Examples of withdrawable circuit breakers

Drawout Masterpact NT circuit Withdrawable Compact NSX Plug-in Compact NSX circuit
breaker (on a chassis). circuit breaker (on a chassis). breaker (on a base).

Technical help Page 15/61

Ecodial AC 4

Electrical operating mechanisms for circuit breakers and

switches
If a circuit breaker or switch requires a motorised electrical operating mechanism, Ecodial selects only
devices offering the option.

If the option is not required, Ecodial proposes solutions without taking the option into account.

In the results zone, Ecodial indicates whether the option exists for each device.

Technical help Page 16/61

Ecodial AC 4

Remote opening of switches

If remote opening of a switch is required, Ecodial selects only devices offering the option.
This function may be used, for example, for load shedding.

If the option is not requested, Ecodial selects only devices that cannot be remotely opened.

In the absence of an indication (parameter set to Any), Ecodial proposes solutions without taking the
option into account.

In all cases, Ecodial indicates in the results zone whether each device can be remotely opened or not.

Technical help Page 17/61

Ecodial AC 4

Visible break
For certain applications, visible breaking of circuit may be required for safety reasons.
On a device offering visible break, the operator can see via a transparent screen that the contacts are in
fact open. For example, the Interpact INV range offers a double safety function with visible break and
positive contact indication.

If visible break is required on a switch, Ecodial selects only switches offering the function.

If it is not required, Ecodial selects only devices not offering the function.

In the absence of an indication (parameter set to Any), Ecodial proposes solutions without taking the
function into account.

In all cases, Ecodial indicates for each device in the results zone whether the function is available.

Technical help Page 18/61

Ecodial AC 4

Classification of residual current devices

Standard IEC 60755 (General requirements for residual-current operated protective devices) defines
three types of residual-current protection depending on the fault-current characteristics.
Type AC
Tripping is ensured for residual sinusoidal alternating currents, without a DC component.

Type A
Tripping is ensured for residual sinusoidal alternating currents and specified residual pulsating direct
currents.

Type B
Tripping is ensured for currents identical to those for class A and for residual direct currents produced by
three-phase rectification.

In addition, Schneider Electric offers the following types of residual-current devices in its catalogue:
SI (super immunised) with reinforced immunity to nuisance tripping in polluted networks,
SiE designed for environments with severe operating conditions.

The table below presents the recommended type and immunity level as a function of the external
conditions and the level of disturbances on the electrical network.

Recommended Risk of nuisance Risk of non-operation (in the presence of a fault)

type tripping
HF leakage Fault current Fault current Low Corrosive or
current with with pure DC temperature dusty
pulsating component (to -25°C) atmosphere
components
AC  
A   
SI   
SiE    
B    

Technical help Page 19/61

Ecodial AC 4

Type of residual-current protection

Residual-current protection may be:
integrated in breaking devices,
or carried out by a separate residual-current relay in conjunction with a separate toroid and a
voltage release (MN or MX).

Ecodial offers a choice between the two possibilities.

If no choice is made (parameter set to Any), the proposed solutions include both integrated and separate
devices that are compatible with the breaking device.

Examples of residual-current protection

Integrated residual current protection Separate
residual-current
relays

Masterpact circuit breaker equipped with Vigicompact NSX iC60 circuit Type M and P
a Micrologic 7.0 control unit circuit breaker breaker with Vigirex relays
add-on Vigi
module

Technical help Page 20/61

Ecodial AC 4

High-sensitivity residual-current protection

The situations and applications presented below require highly-sensitivity residual-current devices, i.e.
devices with a sensitivity I∆n less than or equal to 30 mA.

Example of applications / situation

Additional protection against direct contact
For more information: Electrical Installation Wiki

Premises with fire risk

Power outlets
Swimming pool
Bathrooms (least exposed zone)
In the TT system, when the resistance of the earth electrode for exposed conductive
parts is high (> 500 Ω).
Floor heating

Technical help Page 21/61

Ecodial AC 4

Medium-sensitivity residual-current protection

The situations and applications presented below require medium-sensitivity residual-current devices, i.e.
devices with a sensitivity I∆n less than or equal to 300 or 500 mA.

Example of applications / situation IΔn

Protection against fire risks. ≤ 300 mA
Required for premises with risk of fire or risk
of explosion.
Floor heating ≤ 500 mA

For more information: Electrical Installation Wiki.

Technical help Page 22/61

Ecodial AC 4

Maximum permissible voltage drop for loads

Recommendations and requirements imposed by standards
The maximum, permissible voltage drop for loads varies depending on the installation standard.
Below are the data for standard IEC 60364.

Type of load IEC 60364

Lighting 4% recommended
Other loads 4% recommended

Software parameter setting

In Ecodial, the default values for the maximum permissible voltage drops for loads may be set for each
type of load on the Project parameters tab.
The maximum permissible voltage drop may also be set individually in the properties for each load.

Procedure if the cumulative voltage drop for a load exceeds the permissible value
If the calculated, cumulative voltage drop exceeds the maximum, permissible value, Ecodial displays a
message to signal the error.
To clear the error, reduce the voltage-drop tolerances for the upstream circuits supplying the load (
Circuit voltage-drop tolerances).

For more information: Electrical Installation Wiki.

Technical help Page 23/61

Ecodial AC 4

Circuit voltage-drop tolerances

The default value for circuit voltage-drop tolerances can be set on the Projects parameters tab for:
cables,
busbar trunking systems (BTS).
The maximum permissible voltage drop for a circuit may also be set individually in the properties for each
cable and BTS. Modifying this parameter is a means to customise the distribution of the voltage drop
between the various circuits upstream of a load.

In the example below, the calculated voltage Below, the voltage-drop tolerance for cable WD3
drop for load AA7 is 6.06%, i.e. greater than the has been reduced to 3%. Ecodial consequently
maximum permissible value of 6%. The increases the size of the cable and the voltage
tolerance for circuit voltage drops is set to 5%. drop for load AA7 is now less than 6% (4.98%).

∆u ∆u tolerance
+3.86% 5% → 3%

∆u
+ 1.93%

To maintain the maximum voltage drop for AA7 to less than 6%, it is necessary to reduce the voltage
drops on the upstream circuits (WD3 and WD7) by reducing the voltage-drop tolerance(s).
There are two possible methods.
Reduce the tolerances for all upstream circuits, in which case the size (cross-sectional area) of all
upstream circuits will be increased.
Reduce the tolerance for a single upstream circuit, namely the circuit selected by the designer as the best
for an increase in size.

Technical help Page 24/61

Ecodial AC 4

Cable installation method

Click the Modify installation method command to modify the installation method.

In the window, the information is presented in two steps:

description of the situation and of the installation system,
definition of the parameters for the grouping factor that depends on the installation method.

Ecodial presents in the results zone of the window:

the installation-method number,
the reference method used,
a complete description of the installation method,
a diagram.

Technical help Page 25/61

Ecodial AC 4

Maximum, permissible cross-sectional area

This parameter may be used to limit the size (cross-sectional area) of cables and conductors.
For values above the permissible limit, parallel cables are run in order to comply with the theoretical size
required for the design current of the wiring system.

Technical help Page 26/61

Ecodial AC 4

Cable sizing according to circuit breaker setting or rating

Ecodial provides two possibilities to size cables using as maximum current:
the circuit-breaker setting Ir,
the circuit-breaker rating In.

For example in a circuit where the requested design current is 220A, using a Compact NSX250 with
Mircologic 2.2 trip unit the cable sizing can be made taking into account:
In = 250 A, the cable is sized to 95 mm²,
Or Ir = 220 A, the cable is sized to 70 mm².

Cable sized with circuit-breaker Cable sized with circuit-breaker

rating Ir (250A) setting Ir (220A)

Technical help Page 27/61

Ecodial AC 4

Number of additional touching circuits

When defining cable installation method, some additional settings for grouping factors are available, in
particular the number of additional touching circuits.
In Ecodial this parameter defines the number of other circuits (out of the concerned circuit), that may be
installed in the same installation system (cable tray, conduit, etc.).

If the concerned circuit itself contains several conductors per phase, the grouping factor is automatically
set to the right value by Ecodial.

1 cable of 120 mm² per phase, and is installed 2 cables of 120 mm² per phase and is installed
in a cable tray with 2 other circuits in a cable tray with 2 other circuits

Additional circuits Additional circuits

The number of additional touching circuit has to The number of additional touching circuit has to
be set to 2 be set to 2
Then the grouping factor will be set by Ecodial for Then the grouping factor will be set by Ecodial for
3 touching circuits (the concerned circuit + 2 4 touching circuits (2 for the concerned circuit + 2
additional circuits) additional circuits)

Technical help Page 28/61

Ecodial AC 4

Third-order harmonic distortion

Origin
When the neutral is distributed, non-linear loads may cause large overloads in the neutral conductor due
to the presence of third-order (H3) harmonics.
Balanced three-phase loads do not cause H3 harmonics in the neutral conductor. But H3 harmonics can
reach 80% of the fundamental for non-linear single-phase loads such as single-phase diode-bridge
rectifiers with capacitive filtering.
To know more about harmonic effects in neutral conductor Electrical Installation Wiki.

Single-phase diode-bridge rectifiers with capacitive filtering

Diagram Waveform of current drawn Harmonic spectrum of current drawn

Many devices in a wide range of fields include this type of circuit. They are the main causes of H3
harmonics.

Field Devices
Residential TV, hi-fi, video, microwave ovens, compact fluorescent lamps (CFL), etc.
Services Microcomputers, printers, photocopiers, fax machines, CFLs, etc.
Industry Switch-mode power supplies, variable-speed drives, CFLs, etc.

Impact of neutral protection on cable sizes

Table 52-D1 and §523.5.3 of standard IEC 60364 sums up the rules for neutral protection, selection of
cable sizes and the factors for permissible-current reduction in cables when H3 harmonics are present.

THDI ≤ 15% 15% < THDI ≤ 33% 33% < THDI ≤ 45% THDI > 45%
Sneutral = Sphase/2 is Sneutral = Sphase Sphase = Sneutral Sphase = Sneutral
permissible (1) Sphase is decisive Sneutral is decisive Sneutral is decisive
Neutral protected Factor = 0.86 IBneutral = 3 X THDi x IBneutral = 3 X THDi x IBphase
IBphase Factor = 1
Factor = 0.86

(1) If Sphase > 16 mm² Cu or 25 mm² Alu

Impact on circuit-breaker selection

For single-core cables, only the neutral conductor must be oversized, on the condition that the circuit
breaker is capable of protecting an oversized neutral. When that is possible, Ecodial proposes a circuit
breaker equipped with a 4P3d+OSN trip unit that must been the following conditions:
Irneutral ≥ IBneutral,
Irphase ≥ IBphase, i.e. Irneutral·0.63 ≥ IBphase.

For 4P3d+OSN trip units, the Irphase/Irneutral ratio is constant at 0.63.

Technical help Page 29/61

Ecodial AC 4

Manual and alternate solutions

The Select another product command provides access to two separate functions:
selection of alternate solutions validated by Ecodial during a calculation,
manual selection of a product from the catalogue.
This command is available for the components listed below:
LV cables,
busbar-trunking systems (BTS),
circuit breakers,
switches,
residual-current devices.

Alternate selection
Alternate solutions may be accessed only after a calculation has been validated. If that is the case and
the Select another product command is launched, the selection window automatically opens the
Calculated products window. Then simply select the desired solution using the values proposed in the
selection zone. The results zone is updated with the new solution. When OK is clicked, the solution is
confirmed (locked), i.e. it will be used for future calculations.

Manual selection
A prior, validated calculation is not required to access solutions in the catalogue. If a calculation has not
yet been validated, the selection window automatically opens the Entire catalogue window. If a
calculation has been validated, Ecodial opens the Calculated products selection window. Select Entire
catalogue to access the entire catalogue.
When a product is selected manually from the catalogue, it is "locked" for use in future calculations.

Processing of locked solutions

When a solution has been locked by a user (via a manual or alternate selection), Ecodial no longer
calculates the component, but it does check that the locked solution meets electrotechnical requirements.
If a requirement is not met, the locked solution fails the check, the calculation is stopped and an error
message is issued. To clear the problem, it is necessary to unlock the solution and restart the calculation.

Technical help Page 30/61

Ecodial AC 4

Additional derating coefficients for wiring systems

This coefficient is applied in addition to the other coefficients for the installation method.
The table below provides examples of typical values that should be applied when certain external
conditions exist.

External condition Coefficient values

Premises with risk of explosion 0.85
Significant exposure to solar 0.85
radiation

Technical help Page 31/61

Ecodial AC 4

Waiver of overload-protection requirements for safety

circuits
For safety reasons, an application may need to continue operation even under fault conditions, in which
case overload protection should be inhibited.
The inhibition function is required notably for motors used to remove smoke from public buildings.

Ecodial includes a function to waiver thermal protection for circuit breakers supplying loads.
In this case, two types of circuit breakers are proposed by Ecodial:
circuit breakers without thermal protection and equipped with an MA trip unit,
circuit breakers equipped with a control unit enabling inhibition of thermal protection (e.g.
Micrologic 5 or equivalent).

In that case, Ecodial sizes the circuit breaker and the cable to accept 1.5 times the design current of the
circuit.

Technical help Page 32/61

Ecodial AC 4

Power factor for short-circuits on LV sources

By default, Ecodial proposes the values drawn from Table 11 in standard IEC 60947-2 which specifies the
test conditions used to determine circuit-breaker breaking capacities.

Short-circuit current (kA) Power factor for short-circuits PFsc

Ikmax ≤ 3 0.9
3 < Ikmax ≤ 4.5 0.8
4.5 < Ikmax ≤ 6 0.7
6 < Ikmax ≤ 10 0.5
10 < Ikmax ≤ 20 0.3
20 < Ikmax ≤ 50 0.25
50 < Ikmax 0.2

Technical help Page 33/61

Ecodial AC 4

Calculation of LV-source phase impedances, based on

Ik3max
Ik3max is used to calculate the phase impedances on the upstream network, represented by the LV
source.
c ⋅U
ZL = max r
3 ⋅ Ik3max
R L = Z L ⋅ PFsc
XL = Z L 2 − R L 2

Ur phase-to-phase voltage (V)

Ik3max maximum three-phase short-circuit current (A)
cmax voltage factor ( Main changes following the Cenelec TR50480 report)
PFsc Power factor for short-circuits on LV sources
ZL impedance of phases (Ω)
RL resistance of phases (Ω)
XL inductance of phases at 50 Hz (Ω)

Depending on the type of system earthing, there are a number of dependencies between the different
short-circuit currents (Ik3max, Ik1min, Ief, Ief2min) that must be entered.
Ecodial checks the consistency between the parameters ( Consistency of LV-source input parameters).

Technical help Page 34/61

Ecodial AC 4

Calculation of LV-source neutral impedances, based on

Ik1min
Ik1min is used to calculate the neutral impedances (if the neutral is distributed) on the upstream network,
represented by the LV source.
U
c min ⋅ n
3
ZN = − ZL
Ik1min
RN = ZN ⋅ PFsc
XN = Z N 2 − R N 2

Ur phase-to-phase voltage (V)

cmin voltage factor ( Main changes following the Cenelec TR50480 report)
Ik1min minimum single-phase short-circuit current (A)
PFsc Power factor for short-circuits on LV sources
ZL impedance of phases (Ω)
ZN impedance of neutral (Ω)
RN resistance of neutral (Ω)
XN inductance of neutral at 50 Hz (Ω)

These equations are also valid for the impedance of the PEN conductor in the TN-C system (with a
distributed neutral).

Depending on the type of system earthing, there are a number of dependencies between the different
short-circuit currents (Ik3max, Ik1min, Ief, Ief2min) that must be entered.
Ecodial checks the consistency between the parameters ( Consistency of LV-source input parameters).

Technical help Page 35/61

Ecodial AC 4

Calculation of LV-source PE impedances, based on Ief

Ief is used to calculate the PE impedance in the following cases:
TN-S system and no equipotential bonding near the connection point,
TN-C system, neutral not distributed and no equipotential bonding near the connection point.
If there is equipotential bonding near the connection point, upstream PE impedance is negligible for all
types of system earthing.
In the TT system, upstream PE impedance is never taken into account.

 U U 
 cmin × r cmax × r 
= 
3 3
ZPE -
 Ief Ik3max 
 
 
 U U 
 cmin × r cmax × r 
R PE = 3- 3  × PF
 Ief Ik3max 
sc

 
 
XPE = ZPE 2 − RPE 2

Ur phase-to-phase voltage (V)

cmax voltage factor ( Main changes following the Cenelec TR50480 report)
cmin voltage factor ( Main changes following the Cenelec TR50480 report)
PFsc Power factor for short-circuits on LV sources
Ik3max maximum three-phase short-circuit current (A)
Ief minimum phase/PE fault current (A)
ZPE impedance of PE (Ω)
RPE resistance of PE (Ω)
XPE inductance of PE at 50 Hz (Ω)

Depending on the type of system earthing, there are a number of dependencies between the different
short-circuit currents (Ik3max, Ik1min, Ief, Ief2min) that must be entered.
Ecodial checks the consistency between the parameters ( Consistency of LV-source input parameters).

Technical help Page 36/61

Ecodial AC 4

Calculation of LV-source PE impedances, based on Ief2min

Ief2min is used to calculate the PE impedance in an IT system when there is no earthing equipotential
bonding near the connection point.
If there is equipotential bonding near the connection point, upstream PE impedance is negligible for all
types of system earthing.

 U U 
 cmin × α × r cmax × r 
=
3 3
ZPE -
 2 × Ief2min Ik3max 
 
 
 U U 
 cmin × α × r cmax × r 
=
3 3
R PE - × PFsc
 2 × Ief2min Ik3max 
 
 
XPE = ZPE 2 − RPE 2

α = 3 in IT systems without a neutral

α = 1 in IT systems with a neutral
Ur phase-to-phase voltage (V)
cmax voltage factor ( Main changes following the Cenelec TR50480 report)
cmin voltage factor ( Main changes following the Cenelec TR50480 report)
PFsc Power factor for short-circuits on LV sources
Ik3max maximum three-phase short-circuit current (A)
Ief2min minimum double-fault current (A)
ZPE impedance of PE (Ω)
RPE resistance of PE (Ω)
XPE inductance of PE at 50 Hz (Ω)

Depending on the type of system earthing, there are a number of dependencies between the different
short-circuit currents (Ik3max, Ik1min, Ief, Ief2min) that must be entered.
Ecodial checks the consistency between the parameters ( Consistency of LV-source input parameters).

Technical help Page 37/61

Ecodial AC 4

Consistency of LV-source input parameters

The table below sums up the consistency checks run by Ecodial on the LV-source input parameters.

Inconsistency condition When and where? Justification

Ik1min ≤ In All types of earthing systems with Ik1min may not be less than the
a distributed neutral. rated current.
c min All types of earthing systems with Ik3max / Ik1min is too low.
Ik 3 max× < Ik1 min a distributed neutral. This results in a negative neutral
c max
impedance.
Ief ≤ In TN-S system with no equipotential The fault current may not be less
bonding near the connection point. than the rated current.
TN-C.
c min TN-S system with no equipotential Ik3max / Ief is too low.
Ik 3 max× < If bonding near the connection point. This results in a negative PE(N)
c max
TN-C system without a distributed impedance.
neutral and with no equipotential
bonding near the connection point.
Ief 2 min ≤ In IT system with no equipotential The double-fault current may not
bonding near the connection point. be less than the rated current.
c min IT system with a neutral, but no Ik3max / Ief2min is too low.
Ik 3 max× × 0.5 < Ief 2 min equipotential bonding near the This results in a negative PE
c max
connection point. impedance.
c min 3 IT system, with no incoming Ik3max / Ief2min is too low.
Ik 3 max× × < Ief 2 min equipotential bonding, when the This results in a negative PE
c max 2
neutral is not distributed. impedance.

Technical help Page 38/61

Ecodial AC 4

Type of regulation of LV capacitor banks

Principle
By default, Ecodial proposes the type of regulation (fixed or automatic) of capacitor banks for power factor
correction according to the following rules:
If the power to be corrected (Q upstream + Q downstream) is greater than 15% of the apparent power of
the upstream sources (sum of the apparent powers of upstream transformers used simultaneously), then
Ecodial imposes power factor correction with an automatic capacitor bank.
If not, a fixed capacitor bank can be used and Ecodial therefore proposes both fixed and automatic power
factor correction solutions.
This principle is followed to avoid overvoltage in the installation when the installed power of the capacitor
bank is high with respect to the consumption of the installation. An automatic capacitor bank adjusts the
number of capacitor steps connected according to the level of the load on the installation.

Example of a fixed capacitor bank

Source power = 630 kVA.
Calculate reactive power to be corrected = 46.3 kvar.
Rating of selected solution: 54.5 kvar.
Ratio = 54.5 / 630 = 8.6% (< 15%), allowing the use of a fixed capacitor bank.

Example of an automatic capacitor bank

Source power = 250 kVA.
Calculated reactive power to be corrected = 46.3 kvar.
Rating of selected solution: 51.3 kvar.
Ratio = 51.3 / 250 = 20.5% (≥ 15%), imposing the choice of an automatic capacitor bank (a fixed
capacitor bank cannot be used)

For more information: Electrical Installation Wiki.

Technical help Page 39/61

Ecodial AC 4

Types of LV capacitor banks

Principle
The type of capacitor bank is determined by the level of harmonic disturbances at the point of connection
of the capacitor bank. The flow of harmonic currents in the installation leads to harmonic voltages across
the terminals of the capacitors that can cause overcurrents at harmonic frequencies.

Calculating the harmonic disturbance level Gh/Sn in the installation

The type of capacitor bank is determined by calculating the ratio Gh/Sn, representing the level of
harmonic disturbances in the installation:
Gh: total apparent power (kVA ) of the harmonic loads connected downstream of the main LV
switchboard (MLVS)
Sn: rated apparent power of the transformer(s) supplying the MLVS.

The ratio Gh/Sn is calculated by Ecodial for each capacitor bank, taking into account the loads declared
as harmonic loads.

The ratio Gh/Sn can also be entered directly for each capacitor bank. In this case, the values are locked
and will not be modified by Ecodial in the event of changes in the installation.

Selection criteria
LV capacitor banks are available for 3 levels of harmonic withstand:
Gh/Sn < 15%, "Classic" capacitor banks can be used,
15% ≤ Gh/Sn < 25 %, the capacitor banks must be at least of the "Comfort" type (the "Classic"
type is not allowed),
Gh/Sn ≥ 25%, "Harmony" capacitor banks must be used (the "Classic" and "Comfort" types are
not allowed).

If Gh/Sn exceeds 50%, a special study must be carried out to determine the type of capacitor bank
because harmonic filtering must be installed.
For more information: Electrical Installation Wiki.

Technical help Page 40/61

Ecodial AC 4

Reactive power threshold

This parameter determines the reactive power threshold above which power factor correction is required.
If the reactive power consumed by the installation is less than this value, installation of power factor
correction capacitors is unnecessary even if the PF is less than the Target PF.
The following two conditions must therefore be satisfied before Ecodial will carry out capacitor bank
calculations:
PF < Target PF
Reactive power consumed > Threshold (50 kvar by default).

Technical help Page 41/61

Ecodial AC 4

Coordination of circuit breakers and contactors

Definition
Standard IEC 60947-4-1 defines two types of coordination.

Type Definition
Type 1 Deterioration of the contactor and the relay is acceptable under two conditions:
no danger to operating personnel,
no danger to any components other than the contactor and the relay
Type 2 Only minor welding of the contactor or starter contacts is permissible and the contacts
must be easily separated. Following type-2 coordination tests, the switchgear and
controlgear functions must be fully operational.

When the switchgear and controlgear includes both the circuit breaker and contactor functions,
coordination is considered to be total.

Which type of coordination is needed?

Selection of a type of coordination depends on the operating conditions encountered. The goal is to
achieve the best balance between the user’s needs and the cost of the installation.

Type user’s needs / cost of the optimised installation

Type 1 Qualified maintenance service,
Low cost of switchgear and controlgear,
Continuity of service is not imperative or may be ensured by simply replacing the faulty
motor drawer.
Type 2 Continuity of service is imperative,
Limited maintenance service,
Specifications stipulating type 2.

Technical help Page 42/61

Ecodial AC 4

Trip classes of motor thermal protection

The four trip classes of a thermal relay are 10 A, 10, 20 and 30 (maximum tripping times at 7.2 Ir).
Classes 10 and 10 A are the most commonly used. Classes 20 and 30 are reserved for motors with
difficult starting conditions.
The following diagram and table show the thermal relay suited to the motor starting time.

Trip Class 1,05 Ir 1,2 Ir 1,5 Ir 7,2 Ir

10A t > 2h t < 2h t < 2 min 2 ≤ t ≤ 10 s
10 t > 2h t < 2h t < 4 min 4 ≤ t ≤ 10 s
20 t > 2h t < 2h t < 8 min 6 ≤ t ≤ 20 s
30 t > 2h t < 2h t < 12 min 9 ≤ t ≤ 30 s

For more information: Electrical Installation Wiki.

Technical help Page 43/61

Ecodial AC 4

Motor inrush currents

Principle
When the motor inrush or starting current is greater than 19 Ir, device ratings are increased by 20% to
satisfy optimum starting and coordination conditions.

Example I’’start/Ir ≤ 19
For an 11 kW motor with direct-on-line starting, the following protection is selected:
Circuit breaker: P25 M 23 A,
Contactor: LC1D25.

Example I’’start/Ir > 19

For an 11 kW motor with direct-on-line starting, the following protection is selected:
Circuit breaker: GV2ME 32 A,
Contactor: LC1D32.

Technical help Page 44/61

Ecodial AC 4

Transient over-torque of variable speed drives

Certain applications require an over-torque during transient acceleration and deceleration phases. In this
case, a "high torque" variable speed drive (VSD)should be used. For other applications (e.g. centrifugal
pumps and fans), a VSD with "standard torque" is sufficient.

Standard torque High torque

The over-torque and the associated overcurrent The over-torque and the associated overcurrent
are limited by the VSD to a typical value of 1.2 are limited by the VSD to a typical value of 1.5 to
to 1.4 times the rated current of the VSD for 60 1.7 times the rated current of the VSD for 60
seconds. This setting is compatible with seconds. This setting is compatible with
applications such as centrifugal pumps, fans applications such as handling and grinding
and conveyors. equipment and pumps with high break-off
torques.

Technical help Page 45/61

Ecodial AC 4

Single-pole breaking capacity at phase-to-phase voltage on

IT systems
When a double fault occurs on an IT system, the protective devices must be able to break the double-
fault current on a single pole at the phase-to-phase voltage.
In IT installations, Ecodial therefore checks that the protective device satisfies the following two
conditions:
breaking capacity (Icu) greater than the maximum short-circuit current (Ik3max, Ik2max or
Ik1max),
single-pole breaking capacity at the phase-to-phase voltage greater than the double-fault current.

The short-circuit currents Ik3max, Ik2max and Ik1max are calculated in compliance with Cenelec
TR50480 technical report.
For the double-fault current, Ecodial check that the breaking capacity at the phase-to-phase voltage is
greater than:
the current Ief calculated in compliance with Cenelec TR50480 technical report
0.15 times the 3-phase short-circuit current at the point considered if this current is less than or
equal to 10 000 A,
0.25 times the 3-phase short-circuit current at the point considered if this current is greater than
10 000 A.

Technical help Page 46/61

Ecodial AC 4

Single-pole breaking capacity at phase-to-neutral voltage on

TN systems
For TN installations, the protective devices must be able to break the double-fault current on a single pole
at the phase-to-neutral voltage.
No specific indication exists in standard IEC 60364, however all versions of Ecodial carry out this check
for all protective devices and indicate the single-pole breaking capacity at the phase-to-neutral voltage
when it is different than the breaking capacity Icu of the device.

Technical help Page 47/61

Ecodial AC 4

Feeder distribution for Busbar Trunking System (BTS)

Feeder distribution is used for choosing whether the tap off points on the BTS are placed equidistance
from each other (Uniform) or not (Non Uniform). The choice affects how the voltage drops and short-
circuit currents are calculated.

Uniform Non Uniform

The voltage drop is uniform across any of the The voltage drop varies across the tap off point
tap off points. The voltage drop IS calculated based on distance from origin of the tap off point.
across the entire length of the BTS The voltage drop is calculated for the tap off point

The short circuit set of values stay same across The short circuit set of values vary across tap off
any tap off points points based on there distance from origin.

When designing systems where the details When designing systems where BTS riser needs
about the BTS are not know at the design time, to be used, it is advised to use Non Uniform BTS
it is advised to use Uniform BTS as it will take as the tap off points will not be equidistance from
into consideration derated voltage drop and each other.
short circuit set

Important note: The the busbar trunking system selected by Ecodial will remain the same irrespective of
whether a uniform / non uniform distribution type is chosen as far as the voltage drop is acceptable.

Choosing uniform or non-uniform calculation for busbar trunking system ?

Uniform calculation has to be used for the case of a busbar trunking system in case of:
power distribution where tap-off units can be regularly plugged,
place of the tap-off units can not be determine accurately,
flexibility is required to réorganise a workshop for example, and the tap-off unit may be moved
from a place to another.

For more information: Electrical Installation Wiki.

Technical help Page 48/61

Ecodial AC 4

Distance from origin

This property represents the distance of tap off point’s for the BTS and is seen on feeder circuits
connected to the BTS when the feeder distribution type is set to non uniform. The distance from origin
can be set to zero and should be less than or equal to the length of the BTS to which it is connected.
Multiple tap-off points having same distance from origin can also be specified.

Ecodial does not distinguish between uniform and non uniform from a schematic perspective (SLD).

In case of BTS where feeder distribution is non uniform, the component voltage drop and short circuit set
represented in the report section, shows the total cumulative values of the tap off points along with the
component’s voltage drop and short circuit set.

Technical help Page 49/61

Ecodial AC 4

MV protective device
3 possibilities are available for MV protective device:
“undefined”, in that case Ecodial will not propose any protection device, only the breaking time of
the protection is requested to check the thermal stress of LV connection between transformer and
main switchboard,
“fuse”, in that case Ecodial will select the appropriate fuses for the MV/LV transformer (refer to
MV fuse technology),
“relay”, in that case Ecodial will propose a relay for MV/LV transformer protection (refer to Type of
MV relay).

For more information: Electrical Installation Wiki.

Technical help Page 50/61

Ecodial AC 4

MV fuse technology
DIN and UTE fuses are available in Ecodial.
DIN technology will results in choosing fuses in Fusarc range.
UTE technology will results in choosing fuses in Solefuse range.

Ecodial selects the fuses rating according to voltage and transformer power in order to:
break short-circuit current across the terminal of the transformer secondary,
prevent unexpected tripping due to transformer inrush current.

For more information: Electrical Installation Wiki.

Technical help Page 51/61

Ecodial AC 4

Type of MV relay
Digital and self-powered relays are available in Ecodial providing transformer protection against:
internal short-circuits in MV windings,
internal short-circuits in LV windings,
short-circuits on LV cable or busway between transformer and LV circuit-breaker
it’s also a back-up for main LV circuit-breaker.
This type of protection is also known as ANSI 50/51.

Digital relays
Ecodial calculates default settings with 2 definite-time thresholds for short-circuit detection upstream the
transformer.
The lower threshold is set:
20% lower than minimum LV short-circuit current
seen from MV side Ikmin(LV),
time delay to 0,5 s to prevent tripping during
inrush current.
The upper threshold is set:
greater than transformer assigned current,
greater than transformer inrush current,
greater than the greatest LV short-circuit current
seen from MV side,
20% lower than minimum MV short-circuit current
Ik2min,
time delay is set as lower as possible (0,05 s).

In addition to default settings Ecodial provides a set of parameter for

manual settings:
1 common current setting from 1 to 6250 A,
up to 4 time-current thresholds with there own current and time
setting, by default only 2 activated threshold
Each time-current can be set among definite-time and 5 time-dependent
curves (refer to Time dependent tripping curves for MV digital relay).

VIP 40/45 self-powered relay

Self-powered relay are selected among VIP 40 and VIP 45 ranges designed for transformer protection up
to 200A.
Setting is done through 2 parameters:
current setting, selected by Ecodial in compliance with the transformer rated current,
discrimination with CB threshold, selected when the LV protection is a circuit breaker.

Discrimination with CB threshold activated Discrimination with CB threshold inhibited

Technical help Page 52/61

Ecodial AC 4

Time dependent tripping curves for MV digital relay

5 types of time-dependent tripping curves are available in Ecodial:
SIT,
VIT,
LTI,
EIT,
UI.

The generic equation for time-dependent curves is:

With:
Is = current setting,
T = time delay setting at 10 x Is.

k α β
SIT 0,14 0,02 2,97
VIT 13,5 1 1,5
LTI 120 1 13,33
EIT 80 2 0,808
UI 315,2 2,5 1

1000

SIT VIT - LTI EIT UI

100

10
t (s)

1
1 10 100 1000 10000 100000

0,1

0,01

0,001
I (A)

Time-dependent tripping curves comparison, for Is = 10 A

Technical help Page 53/61

Ecodial AC 4

UPS inputs connection

In Ecodial only on-line UPS are available, for more information on this technology: Electrical Installation
Wiki.
Ecodial proposes 2 possibilities for the inputs connection:
common, in that case Normal and Bypass are connected and fed by one feeder circuit with one
common upper protection,
separated, in that case Normal and Bypass are connected to separate upstream feeder.

The default value proposed by Ecodial depends on the UPS characteristics and power:
for small UPS (low power) the connections are common by default,
for medium and high power UPS the connections are separated by default.
When the default value is “Common” it’s possible to change it to “Separated”, in that case the lock next to
the parameter closes .

Common Normal and Bypass connection Separated Normal and Bypass connection

Technical help Page 54/61

Ecodial AC 4

UPS requested redundancy

This parameter is used to define the level of redundancy requested for the UPS solution.
Ecodial sizes the UPS taking into account the following rules:
the UPS power has to be greater or equal to the power demand,
the UPS power has to be at least twice greater than the biggest downstream feeder in order to
ensure proper discrimination between this feeder and UPS internal output protection.
When a redundancy level is requested Ecodial will select a solution with multiple UPS units in order that
in case of a failure on one unit the percentage of redundancy can be used to supply downstream
installation.

Here is an example with 2 feeders connected downstream an USP with respective power demand:
- 100 kVA,
- 10 kVA.
Taking into account the diversity factor of 0.9 on bubsar WC15 the total power demand for the UPS is 99
kVA.
The following table shows the solutions proposed by Ecodial depending the requested level of
redundancy.

Solution Calculation rules

No redundancy Galaxy PW 1 x 200 kVA SUPS ≥ 99 kVA,
SUPS ≥ 2 x 100 kVA.
50% redundancy Galaxy PW 3 x 100 kVA including: SUPS ≥ 99 kVA,
2 x 100 kVA for power demand request, SUPS ≥ 2 x 100 kVA,
1 x 100 kVA for requested redundancy. Sredundancy ≥ 0,5 x SUPS
100% redundancy Galaxy PW 4 x 100 kVA including: SUPS ≥ 99 kVA,
2 x 100 kVA for power demand request, SUPS ≥ 2 x 100 kVA,
2 x 100 kVA for requested redundancy. Sredundancy ≥ 1 x SUPS

Technical help Page 55/61

Ecodial AC 4

UPS mode
When UPS inputs connection are separated, Ecodial requests the definition of an operating mode to
describe the operating conditions for bypass input.
Once an operating mode is created for bypass operating condition, the UPS mode parameter has to be
set to “Bypass”.

Technical help Page 56/61

Ecodial AC 4

UPS transformer requested

Ecodial offers the possibility to request a downstream LV/LV transformer, sized according to UPS
selection.
By default the option is set to “False”, when the user set is to “True”, then an output LV/LV transformer is
selected allowing:
galvanic insulation between upstream and downstream circuit
voltage adaptation between primary and secondary,
system earthing arrangement adaptation between primary and secondary Electrical Installation
Wiki.

Without transformer With transformer requested

In that case, output voltage and system earthing

arrangement can be set to a different value from
input.

Transformers can also be used on input connection of the UPS.

In that case Ecodial will check the following rules:
consistency of voltage coming from Normal and Bypass input,
consistency of system earthing arrangement coming from Normal and Bypass input.

For more information: Electrical Installation Wiki.

Technical help Page 57/61

Ecodial AC 4

Number of UPS
This is the total number of UPS unit for the solution including:
UPS to supply power demand,
UPS for redundancy, refer to UPS requested redundancy.

Technical help Page 58/61

Ecodial AC 4

Number of UPS for redundancy

This is the number of UPS that have been sized to take into account the requested redundancy:
refer to UPS requested redundancy.

Technical help Page 59/61

Ecodial AC 4

Number of bypass
Depending on the USP technology, in case of multiple unit solution, 2 types of bypass can be proposed:
solution with one bypass per UPS unit,
solution with a bypass common to several units.

In case of a solution with common bypass, the number of bypass displayed by Ecodial will be lower than
the number of UPS unit.

One bypass per UPS unit Common bypass for several units

Technical help Page 60/61

Ecodial AC 4

Battery backup time

This information is not calculated by Ecodial, but Ecodial provides the standard range possibilities for the
selection UPS.
For more information on UPS battery: Electrical Installation Wiki.

Technical help Page 61/61