Product Catalog Edition 4

Table of Contents
Technical Product Information

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Duct Connection Products Flange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Corner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Cleat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Butyl Gasket . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Neoprene Tape Gasket . . . . . . . . . . . . . . . . . .6 Slip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Duct Hangers and Strapping Trapeze Hanger . . . . . . . . . . . . . . . . . . . . . . . .8 Hanger Strap . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Threaded Rod. . . . . . . . . . . . . . . . . . . . . . . . . . .8 . . . . . . . . . . . . . . . . . . . . . . . . . .9 Angle Iron Bull Nosing . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Duct Component Products Vane and Rail . . . . . . . . . . . . . . . . . . . . . . . . .10 TM . . . . . . . . . . . . . . . . . . . . . . . . .10 Quick Rail Flexible Connector . . . . . . . . . . . . . . . . . . . . .11 Spiral Duct Connectors Keating Koupling . . . . . . . . . . . . . . . . . . . . . .12 Quick Flange . . . . . . . . . . . . . . . . . . . . . . . . . .12 Quick Connect . . . . . . . . . . . . . . . . . . . . . . . .13 Access Doors Compression Duct Doors . . . . . . . . . . . . . . .14 Spin-In Access Doors . . . . . . . . . . . . . . . . . .14 Square Access Doors . . . . . . . . . . . . . . . . . .15 Adhesives and Sealants Roller-Type Adhesive . . . . . . . . . . . . . . . . . . .16 Spray-Type Adhesive . . . . . . . . . . . . . . . . . . .16 Solvent-Based Sealant . . . . . . . . . . . . . . . . .16 Water-Based Sealant . . . . . . . . . . . . . . . . . .17 Water-Based Reinforced Sealant . . . . . . . .17 Pumpable Butyl Sealant . . . . . . . . . . . . . . . .17

Hardware and Tools Rod Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Rod Lock Install Tool . . . . . . . . . . . . . . . . . . .18 Weld Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Isolation Hanger . . . . . . . . . . . . . . . . . . . . . . .18 Strap Buckle . . . . . . . . . . . . . . . . . . . . . . . . . .19 Moisture Drain . . . . . . . . . . . . . . . . . . . . . . . .19 Cleat Install Tool . . . . . . . . . . . . . . . . . . . . . . .19 Corner Injector . . . . . . . . . . . . . . . . . . . . . . . . .20 Crimper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Pneumatic QuickShot Gun . . . . . . . . . . . . . .20 Cut-Off Saw . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Sealant Application System . . . . . . . . . . . . .21 Adhesive Spray Pump . . . . . . . . . . . . . . . . . .21 Damper/Regulator Accessories Damper Sets . . . . . . . . . . . . . . . . . . . . . . . . . .22 Damper Regulator Sets . . . . . . . . . . . . . . . . .23 Damper Tip. . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Casing Clips . . . . . . . . . . . . . . . . . . . . . . . . . .23 Spiral Diffusers . . . . . . . . . . . . . . . . . . . . . .24 Fire Dampers Reference Guide . . . . . . . . . . . . . . . . . . . . . .25 Model Summary . . . . . . . . . . . . . . . . . . . . . . .25 Important Facts . . . . . . . . . . . . . . . . . . . . . . . .26 75 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 85 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 95 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 105 Series . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Sleeves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Retaining Angle . . . . . . . . . . . . . . . . . . . . . . .31 Ceiling Radiation Dampers Reference Guide . . . . . . . . . . . . . . . . . . . . . .32 Model Summary. . . . . . . . . . . . . . . . . . . . . . . .32 50 Series (square and rectangular) . . . . . . .33 55 Series (round) . . . . . . . . . . . . . . . . . . . . . .33 CRDs with Boot . . . . . . . . . . . . . . . . . . . . . . .34 Thermal Blanket . . . . . . . . . . . . . . . . . . . . . . .34 Condenser Support System. . . . . . . . . . . . .35

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866)(630) 595-7868 TEL: (630) 766-5240 FAX: 466-9335
2
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

Introduction
Technical Product Information

Ward Industries offers a complete line of premium duct system components for the sheet metal, insulation, heating, and air conditioning industries. Our extensive product line makes us the first choice for all your duct system component requirements. In addition to the J and H flange connector systems, Ward Industries offers spiral duct connectors, slips and drive, vane and rail, and a wide range of gaskets, adhesives, and sealants. The accessory products include fire dampers, ceiling radiation dampers, and access doors. Timesaving tools like the Injector and the QuickShot support the installation of the Ward product line, as well as provide cost-saving opportunities for our customers. Ward Industries products provide high performance you can depend on.

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866) 466-9335
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

Duct Connection Products

Technical Product Information

Flange
Available in specialty metals Provides a large butyl-filled integrated sealant pocket to ensure proper sealing Offers a metal shoulder to protect gasket Available in 10' and 20' lengths Recommended for 14-gauge through 26-gauge ductwork

Model FLG J J-rated Flange 20-gauge galvanized steel Meets SMACNA rigidity Class J for transverse joints (steel) Meets SMACNA rigidity Class H for transverse joints (aluminum)

Model FLG H H-rated Flange 22-gauge galvanized steel Meets SMACNA rigidity Class H for transverse joints (steel)

Model Q FLG J QUICK FLANGE TM J-rated Flange 20-gauge galvanized steel Meets SMACNA rigidity Class J for transverse joints (steel) Meets SMACNA rigidity Class H for transverse joints (aluminum)

Model Q FLG H QUICK FLANGE TM H-rated Flange 22-gauge galvanized steel Meets SMACNA rigidity Class H for transverse joints (steel)

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866)(630) 595-7868 TEL: (630) 766-5240 FAX: 466-9335
4
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

Duct Connection Products

Technical Product Information

Corner
Formed galvanized steel Available in specialty metals to match flange material

Model CNR J J Flange Corner Nuts and bolts included (galvanized)

Model CNR H H Flange Corner Nuts and bolts included (galvanized)

Model CNR TC TDC Flange Corner Use with TDC-formed flange

Model CNR TF TDF Flange Corner Use with TDF-formed flange

Model CNR CC Cornermatic TDC Flange Corner 16-gauge Use with Cornermatic corner injection machines

Model CNR CF Cornermatic TDF Flange Corner 16-gauge Use with Cornermatic corner injection machines

Cleat
Formed galvanized steel Available in specialty metals to match flange material Available in 10' or 6" lengths Available in .070" thick extruded PVC for breakaway connections (6" only)

Model CLT W W Cleat Use with Ward J and H flange, as well as TDCformed flange

Model CLT F F Cleat Use with TDF-formed flange

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866) 466-9335
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

Duct Connection Products

Technical Product Information

Butyl Gasket
Provides a nondrying, permanently flexible gasket Adheres to a variety of clean, dry surfaces Contains high percentage of virgin butyl rubber to enhance its sealing and aging characteristics Formulated to retain handling properties through a wide temperature range Will not crack or separate while being applied at low temperatures Product is UL-listed

Model GSK-BT Butyl Tape Gasket Product is 3/16" x 5/8" and is available in 30' rolls Product is 3/16" x 5/8" and is available in 25' rolls

Model GSK-BP Butyl Patch Gasket Product is 3/16" thick, and is available in 1" x 2" and 2" x 3" patch sizes

Neoprene Tape Gasket

Closed-cell foam comprised of neoprene, PVC, and nitrile Has good chemical resistance and is flame-rated Product is 5/16" x 3/4", and is available in 50' rolls Product is UL-listed

Model GSK-NT

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866)(630) 595-7868 TEL: (630) 766-5240 FAX: 466-9335
6
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

Duct Connection Products

Technical Product Information

Slip
Roll-formed galvanized steel Available in specialty metals Available in 5' and 10' lengths

Duct

Duct

Model SLF Flat slip Available in 22-gauge through 26-gauge Duct

Model SLS Standing slip Available in 1/2" in 24-gauge and 26-gauge Available in 1" in 20-gauge through 26-gauge

Duct

Drive
Roll-formed galvanized steel Available in specialty metals Available in 5' and 10' lengths
Model DRS Standing drive Available in 24-gauge and 26-gauge Available in 1" height

Duct Model DRF Flat drive Available in 22-gauge through 26-gauge

Duct Duct Duct

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866) 466-9335
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

Duct Hangers and Strapping

Technical Product Information

Trapeze Hanger
Roll-formed galvanized steel Slotted holes 2-1/4" on center Available in both 16-gauge and 18-gauge Available in 10' and 20' lengths Inexpensive, yet strong alternative to standard strut systems Compatible with multiple clamp and component items Use trapeze washer (TZW) and threaded rod for a complete system (sold separately)

Model TZH and Model TZW

Threaded Rod
Zinc-plated threaded rod Available in standard thread diameters ranging from 1/4" to 7/8" Available in 6', 10' or 12' lengths Use with trapeze hanger and washer for a complete hanging system (sold separately)

Model THR

Hanger Strap
Galvanized steel Available in 16-gauge through 24-gauge Available in 200' rolls or 10' flat blanks Great multipurpose product for hanging ductwork Use with strap buckle for quick and easy installation

Model SHR Model SHB (10' strip) also available

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866)(630) 595-7868 TEL: (630) 766-5240 FAX: 466-9335
8
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

Duct Hangers and Strapping

Technical Product Information

Angle Iron
Roll-formed galvanized steel Slotted and punched holes 4" on center Available in 14-, 16-, and 18-gauge Available in 12' lengths Great multipurpose product

Model AGS - slotted

Model AGP - punched

Model AGX - solid

Bull Nosing
Formed 26-gauge galvanized steel Self-adhesive tape provides quick and easy installation Available in sizes for insulation from 1/2" to 2" thick

Model BLN

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866) 466-9335
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

Duct Component Products

Technical Product Information

Vane and Rail

Roll-formed galvanized steel Available in specialty metals Available in 10' lengths Custom lengths available Double-wall turning vane and turning rail designs in accordance to SMACNA guidelines

2" Vane

4" Vane Model RAL Roll-formed 22-gauge galvanized steel (2" and 4") Provides extra wide margin for easy fastening Rail stacks to minimize storage and shipping requirements Self-aligning tabs for easy vane installation Vane and Rail assembly

Model VNN/VNA Roll-formed 24-gauge galvanized steel (4") Roll-formed 26-gauge galvanized steel (2") Acoustical vane utilizes a perforated inner vane wall and insulation for sound absorption

Quick Rail

TM

Model FRI RAL Quick RailTM Roll-formed 22-gauge galvanized steel (2" Rail Only) Eliminates the tedious process of bending over each vane to secure it to the rail

Two tabs instead of one Eliminates loose connections that can cause
annoying rattle over time Self-aligning tabs for easy vane installation Self-centers vanes onto rails Holds the vanes tangent to the airstream eliminating trailing edges

Quick RailTM eliminates extra assembly steps

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866)(630) 595-7868 TEL: (630) 766-5240 FAX: 466-9335
10
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

Duct Component Products

Technical Product Information

Flexible Connector
Roll-formed galvanized steel and fabric Available in specialty metals Available in both commercial and residential grades Available with two different styles of seam wraps Available in 100' rolls All fabrics rated to 10" S.P. Absorbs sound and vibration to prevent from transmitting throughout system
Model FC

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866) 466-9335
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

11

Spiral Duct Connectors

Technical Product Information

Keating Koupling
Formed 20-gauge galvanized steel Available in specialty metals Provides a large butyl-filled integrated sealant pocket to ensure proper sealing Available for both round and flat oval duct Available in sizes ranging from 10" to 72" Provides a connection that is virtually airtight up to 16" S.P. Provides a smooth, clean appearance for exposed installation

Model KKC - oval Model KKC - round

Quick Flange
Formed 16-gauge galvanized steel Available in specialty metals, except stainless steel Available for both round and flat oval duct Available in sizes ranging from 10" to 72" Provides a quick and easy method for connecting round and oval duct

Model QFC - round

Model QFC - oval

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866)(630) 595-7868 TEL: (630) 766-5240 FAX: 466-9335
12
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

Spiral Duct Connectors

Technical Product Information

Quick Connect
Formed 24-gauge galvanized steel Contains closed-cell polyethylene gasket to ensure proper sealing requirements Available for round duct Available in sizes ranging from 3" to 12" Provides a quick and unique connection for round duct

Model QCC

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866) 466-9335
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

13

Access Doors
Technical Product Information

Compression Duct Door

Formed galvanized steel Available in specialty metals Available in sizes 8" x 4", 10" x 6" and 16" x 12" Available for both flat and round duct Self-adhesive template included for proper installation

Model DSA for Single-Wall Duct Formed 20-gauge galvanized steel Contains polyfoam insulation Utilizes closed-cell neoprene gasket to ensure proper sealing requirements Pressure tested to over 20" WG

Model DSA DW for Double-Wall Duct Formed 20-gauge galvanized steel Contains polyfoam insulation Utilizes closed-cell neoprene gasket to ensure proper sealing requirements Increased bolt length allows door to encompass double wall or insulated duct Pressure tested to over 20" WG

Model DSA HT for High-Temperature Duct Formed 16-gauge black iron Utilizes ceramic rope gasket For applications up to 2000F

Spin-In Access Doors

Formed 22-gauge galvanized steel frame Formed 24-gauge galvanized steel door Fiberglass encapsulated in 1" thick door, providing an estimated R-value of 3 Utilizes closed-cell neoprene gasket Available in sizes from 8" to 24" diameter Tested to 20" S.P. with minimal leakage

Model DSP

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866)(630) 595-7868 TEL: (630) 766-5240 FAX: 466-9335
14
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

Access Doors
Technical Product Information

Square Access Doors

Formed 22-gauge galvanized steel frame Formed 24-gauge galvanized steel door Fiberglass encapsulated 1" thick door Preformed dovetail tabs allow for easy and quick installation Available in sizes from 6" x 6" to 24" x 24" Available with or without insulation Available for high-pressure applications Other options available; call with requests

Model DCM Square Cammed Door Provides an estimated R-value of 3 Utilizes open-cell polyester foam gasket Dual-cam design offers complete removal of door for accessing duct Tested to 4.5" S.P. with minimal leakage

Model DHG Square Hinged Door Provides an estimated R-value of 3 Utilizes open-cell polyester foam gasket Full-length hinge allows door to pivot out of the way for easy access to the duct Tested to 4.5" S.P. with minimal leakage

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866) 466-9335
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

15

Adhesives and Sealants

Technical Product Information

Roller-Type Adhesive
Model AR05 Designed for bonding duct liner, duct wrap and fibrous glass insulations to painted steel, galvanized, or aluminum duct Can also be used as a contact bond adhesive in areas where water entrapment may be a problem Water-based product UL-listed, meeting NFPA 90A and 90B 25/50 requirements Available in 5-gallon buckets

Spray-Type Adhesive
Model AS55 Designed for bonding fiberglass and mineral wool duct liner to galvanized duct Ideal for applying with high-volume spray and coil line operations Can also be applied by extrusion or manual spray equipment Water-based product UL-listed, meeting NFPA 90A and 90B 25/50 requirements Available in 55-gallon drums

Solvent-Based Sealant
Model SSTB/SS01 Designed as a high velocity duct joint sealant for indoor applications Can also be used to adhere duct fabrics and flexible duct to high velocity ducts UL-listed, meeting NFPA 90A and 90B 25/50 requirements Available in 1-gallon buckets or 11-ounce tubes

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866)(630) 595-7868 TEL: (630) 766-5240 FAX: 466-9335
16
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

Adhesives and Sealants

Technical Product Information

Water-Based Sealant
Model SWTB/SW01 Designed as a vapor barrier duct sealant Can be applied to galvanized, aluminum, or mild steel ducts Ideal for sealing ASJ, FRK, and FSK jackets and board facings at joints or laps Also use over staple and weld pin punctures The cartridge grade is an ideal joint sealant with polystyrene insulation UL-listed, meeting NFPA 90A and 90B 25/50 requirements Available in 1-gallon buckets or 11-ounce tubes

Water-Based Reinforced Sealant

Model SWFTB/SWF01 Designed as a vapor barrier duct sealant Can be applied to galvanized, aluminum, or mild steel ducts Also use over staple and weld pin punctures Fiber reinforcement ensures that it is tough yet flexible UL-listed, meeting NFPA 90A and 90B 25/50 requirements Available in 1-gallon buckets or 11-ounce tubes

Pumpable Butyl Sealant

Model SBTB/SB05/SB55 Provides a nondrying, permanently flexible seal for rigid or expansion joints on a variety of materials Provides a moisture and vapor-tight seal Available in 55-gallon drums, 5-gallon buckets, or 11-ounce tubes

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866) 466-9335
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

17

Hardware and Tools

Technical Product Information

Rod Lock
Zinc-plated grade 5-bolt Zinc-plated washer with neoprene gasket Zinc-plated nut with spring steel seat plates Available in both 1/2" and 3/4" sizes Use with standard conduit to provide quick and easy installation of tie rods Use for both joint and center tie rods Pull-tested to over 1,900 lbs. Use rod lock tool for easy installation (sold separately)
Model RL

Rod Lock Install Tool

Installs Rod Lock nuts quickly and accurately in conduit

Weld Pins
Available in 1/2" 3/4" 1", 1-1/2" and 2" sizes Cupped head for insulation protection Compatible with most weld machines used to apply pins up to 2" in length

Model RODLOCK

Model WP CH

Isolation Hanger
Rubber padding prevents noise transmission from vibrating ducts to the rest of the building

Model IH

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866)(630) 595-7868 TEL: (630) 766-5240 FAX: 466-9335
18
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

Hardware and Tools

Technical Product Information

Strap Buckle
Ideal for hanging round duct Hanger strap is bent into the strap buckle and suspended with threaded rod

Model SB

Moisture Drain
Creates a leak-proof drain Allows moisture in ductwork to collect in one area for easy draining Use with moisture drain cap (MC) for a complete drain assembly (sold separately).

Model MD

Cleat Install Tool

Installs finishing cleat quickly and easily

Model CLEAT

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866) 466-9335
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

19

Hardware and Tools

Technical Product Information

Corner Injector
Automatically inserts corners into flange, two at a time Adaptable for either Ward J or H Flange Total time per cycle is less than 5 seconds
Model INJECTOR

Crimper
Installs Ward TDC corners in TDC-formed flange Installs Ward TDF corners in TDF-formed flange Forms hem, presses to crimp, and secures the corner in the flange

Model CRIMPER

Pneumatic QuickShot Gun

QuickShot is a combination pneumatic nailer and screwdriver that pierces through metal Holds the Ward flange in position while fastening to ensure proper installation Provides additional strength by increasing thread engagement Reduces possibility of leakage (fasteners will not strip) Total time per screw is less than a second Also use as general purpose fastening tool for installing turning vane and exterior reinforcements
Model QUICKSHOT

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866)(630) 595-7868 TEL: (630) 766-5240 FAX: 466-9335
20
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

Hardware and Tools

Technical Product Information

Cut-Off Saw
14" metal cutting blade and pneumatically controlled vice guarantee a burr-free cut Ensures operator protection with a heavy-gauge blade guard Optional counter shuts down the cutting cycle after predetermined number of cuts Total time per cut is less than a second

Model QUICK SAW

Sealant Application System

Provides easy application of pumpable butyl for proper sealing of longitudinal joints

Model SEALER

Adhesive Spray Pump

Provides easy application of Ward Industries spray adhesive Offers an adjustable range of settings Provides an extremely fine, uniform coating required for proper application Clean-up is fast and easy

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866) 466-9335
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

21

Damper/Regulator Accessories
Technical Product Information

Damper Sets
Model 65 and 66 Damper Set For use in 5" to 6" round pipe One bearing Furnished with handle, washer, and wing nut Unassembled
Model 65 and 66 Damper Set

Model 607 and 608 Damper Set For use in 7" and 8" round pipe Two bearings Furnished with handle, washer, and wing nut Unassembled

Model 607 and 608 Damper Set

Model 506, 507, and 508 Damper Set 6", 7", and 8" sizes Steel warm air damper Spindle is reversible and may be inserted from either end Heavy spring holds damper securely under most conditions

Model 506, 507, and 508 Damper Set

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866)(630) 595-7868 TEL: (630) 766-5240 FAX: 466-9335
22
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

Damper/Regulator Accessories
Technical Product Information

Damper Regulator Sets

Damper regulator sets are furnished with retractable bolt bearing for fast, easy assembly. Merely slip bearing over edge of damper at the bearing line, lay the bearing on any firm surface, and drive the prong through the damper. The prong firmly clinches the bearing to the damper. 5/16" bearings are ample for most damper installations. Maximum damper thickness: .022, 22-gauge galvanized Model 69 Damper Regulator Set 704 Washer 705 Handle 706 Wing Nut 708 (one) 5/16" Bearing

Model 69 Damper Regulator Set

Model 70 Damper Regulator Set 704 Washer 705 Handle 706 Wing Nut 708 (one) 5/16" Bearing
Model 70 Damper Regulator Set

Model 80 Damper Regulator Set 60 - 3/8" Regulator 56 - 3/8" Square Shank Bearing 60 - 3/8" Dial Regulator Set for large dampers
Model 80 Damper Regulator Set

Damper Tip
Fixed bearing
Model 102 Damper Tip

Casing Clips
For fastening casings and drawbands
Model 2 Casing Clip 14-gauge steel Model 27 Casing Clip 16-gauge steel

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866) 466-9335
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

23

Spiral Diffusers
Technical Product Information

Spiral Diffusers
Extruded aluminum construction Available as diffuser only or diffuser with air scoop Optional face adjustable scoop to direct airflow Counter-sunk screwholes Available in Bright White and Satin Anodized finishes Performance data available upon request

Model WSV Single-Deflection Diffuser One-way deflection Single row of individually adjustable blades for deflection control Available sizes: 10" x 3" to 36" x 12" for 6" to 30" ducts

Model WSVH Double-Deflection Diffuser Two-way deflection Two rows of individually adjustable blades for horizontal and vertical deflection control Available sizes: 10" x 3" to 36" x 12" for 6" to 30" ducts

Model WSS Linear Face Diffuser Slot sizes available: 1/2", 3/4", 1" Two rows of individually adjustable blades for horizontal and vertical deflection control Available in one to four slots tall x 48" wide for 6" to 30" ducts

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866)(630) 595-7868 TEL: (630) 766-5240 FAX: 466-9335
24
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

Fire Dampers
Technical Product Information

Reference Guide
75 Series 1.5-hour fire rating Used in barriers rated at 2 hours or less Has a 4-1/4" side profile 165F fusible link standard (212F and 286F also available) Available in both horizontal (H) and vertical (V) damper orientations Available in A, B, and C type configurations Available in S4 stainless steel Damper Orientation Guide H Horizontal V Vertical

Configuration Reference Guide A Damper blades and damper frame are in the air stream. B Damper blades are out of the air stream, but the damper frame is in the air stream. C Damper blades and damper frame are both removed from the air stream. The C configuration requires the damper to be fitted with a collar that will correspond to the type of duct being used. CO Designates an oval collar for use with oval ductwork.

85 Series (Thinline) 1.5-hour fire rating Used in barriers rated at 2 hours or less Has a 2" side profile 165F fusible link standard (212F and 286F also available) Available in both horizontal (H) and vertical (V) damper orientations Available in A, B and C type configurations

95 Series (Thinline) 3.0-hour fire rating Used in barriers rated at 4 hours or less Has a 2" side profile 165F fusible link standard (212F and 286F also available) Available in vertical (V) damper orientation only Available in A, B, and C type configurations

CR Designates a rectangular collar for use with flat ductwork. C Designates a round collar for use with round ductwork.

105 Series 3.0-hour fire rating Used in barriers rated at 4 hours or less Has a 4-1/4" side profile 165F fusible link standard (212F and 286F also available) Available in vertical (V) damper orientation only Available in A, B, and C type configurations

Model Summary
Model 75 Series 85 Series 95 Series 105 Series Hour Rating 1.5-hour 1.5-hour 3-hour 3-hour Side Profile Wide (4") Thinline (2") Thinline (2") Wide (4")

Order width x height with the width being the blade direction.
Damper Orientation H and V H and V V V Configuration A, B, and C A, B, and C A, B, and C A, B, and C

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866) 466-9335
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

25

Fire Dampers
Technical Product Information

Important Facts
Ward Industries fire dampers are undersized 1/4" at the factory (size minus 1/4").

Fire Damper Sleeves

A fire damper sleeve is a rectangular piece of sheet metal (usually the same gauge as the ductwork or heavier) that is wrapped around the damper in order to meet the UL 555 installation instructions. The damper sleeve serves two functions. In many cases it provides a fastening site for the ductwork on either side of the damper. Secondly, a damper sleeve acts as a platform to attach the retaining angle. Fire damper sleeves are available in 8" to 20" lengths (4" increments) and gauges 14 through 22.

Retaining Angles Retaining angles attach to the fire damper sleeve on either side of the barrier (wall or floor) for the purpose of securing the damper in place. The retaining angles frame the damper on each side to secure it in position in the barrier and to cover the gap between the damper and the opening in the barrier.

Fusible Links 165F link is standard. To order 212F or 286F link, specify at the time of order.

Listed to Underwriters Laboratories Standard 555

This product is listed by UNDERWRITERS LABORATORIES, INC. and bears the mark:

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866)(630) 595-7868 TEL: (630) 766-5240 FAX: 466-9335
26
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

Fire Dampers
Technical Product Information

75 Series 1.5-Hour Fire Damper

Roll-formed 22-gauge galvanized frame Roll-formed 22-gauge galvanized blades Available in stainless steel Stainless steel closure spring (horizontal models only) Available in vertical (V) or horizontal (H) models Available in both single and multiple unit sizes Minimum width 6" Maximum single unit size (damper) Vertical: 60" x 60" Horizontal: 60" x 60" Maximum multiple unit size (damper) Vertical: 120" x 120" Horizontal: 102" x 60" UL-listed, curtain-style fire damper for static systems Tested to UL 555, File R16475 Meets NFPA 90A requirements Listed with California State Fire Marshall, Listing 3225-1577:100

75VA and 75HA

Type 75VB Type 75HB

75VC and 75HC

75VCO, 75VCR and 75HCO, 75HCR

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866) 466-9335
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

27

Fire Dampers
Technical Product Information

85 Series 1.5-Hour Fire Damper

Roll-formed 22-gauge galvanized frame Roll-formed 22-gauge galvanized blades Stainless steel closure spring (horizontal models only) Available in vertical (V) or horizontal (H) models Available as single units only Minimum width 6" Maximum single unit size (damper) Vertical: 41" x 36" or 36" x 60" Horizontal: 41" x 36" Thinline frame for applications with space constraints UL-listed, curtain-style fire damper for static systems Tested to UL 555, File R16475 Meets NFPA 90A requirements Listed with California State Fire Marshall, Listing 3225-1577:100

85VA and 85HA

85VB and 85HB

85VC and 85HC

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866)(630) 595-7868 TEL: (630) 766-5240 FAX: 466-9335
28
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

Fire Dampers
Technical Product Information

95 Series 3-Hour Fire Damper

Roll-formed 22-gauge galvanized frame Roll-formed 22-gauge galvanized blades Available in vertical (V) models only Available as single units only Minimum width 6" Maximum single unit size (damper) Vertical: 48" x 49" Thinline frame for applications with space constraints UL-listed, curtain-style fire damper for static systems Tested to UL 555: File R16475 Meets NFPA 90A requirements Listed with California State Fire Marshall: Listing 3225-1577:100

95VA

95VB

95VC

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866) 466-9335
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

29

Fire Dampers
Technical Product Information

105 Series 3-Hour Fire Damper

Roll-formed 22-gauge galvanized frame Roll-formed 22-gauge galvanized blades Available in vertical (V) models only Available as single units only Minimum width 6" Maximum single unit size (damper) Vertical: 60" x 48" UL-listed, curtain-style fire damper for static systems Tested to UL 555: File R16475 Meets NFPA 90A requirements Listed with California State Fire Marshall: Listing 3225-1577:100

105VA

105VB

105VC

105VCO, 105VCR

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866)(630) 595-7868 TEL: (630) 766-5240 FAX: 466-9335
30
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

Fire Dampers
Technical Product Information

Sleeves
UL-listed fire damper factory mounted in a galvanized sleeve Available in the following lengths: 8" 12" 16" 20" Available in the following gauges: 14 16 18 20 22 Available in stainless steel (with model 75 only) Damper can be ordered offset from center for sidewall applications Provides a fastening site for ductwork leading to the damper Provides a platform to which retaining angle can be mounted

Type A

Type C

Type B

Type CO and CR

RETAINING ANGLE
Used to retain fire damper and sleeve assembly in firerated partition Sandwiches the partition to prevent stress on the damper caused from partition expanding and contracting Required on all fire damper and sleeve installations

Model RET ANG

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866) 466-9335
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

31

Ceiling Radiation Dampers

Technical Product Information

50 Series - Square and Rectangular

WCRD-50-4X Single-blade damper Great for smaller sized dampers where maximizing airflow is essential Rectangular Available in 8" x 4", 10" x 4", and 12" x 4" only 165F fusible link standard (212F also available) WCRD-50 Dual-blade damper, arranged in a butterfly configuration Square or rectangular Minimum size - 4" x 4" Maximum size - 24" x 24" 165F fusible link standard (212F also available) Available with easy access hook and catch

Easy Access Suffix

EA - Easy Access LP - Link Plate The easy access feature allows for easy access to reset the damper.

55 Series - Round
WCRD-55 Dual-blade damper, arranged in a butterfly configuration Round Sizes range from 4" to 24" diameter 165F fusible link standard (212F also available) Available with easy access hook and catch

Order width x height with the width being the direction of the damper hinge.

Model Summary
Model WCRD-50-4X WCRD-50 WCRD-50-B WCRD-50-4XB WCRD-55 Side Profile Square/Rec tangular Square/Rec tangular Square/Rec tangular w/boot Square/Rec tangular w/boot Round Blade Orientation Single Blade Double Blade Double Blade Single Blade Double Blade Configuration Easy acces s only Easy acces s or link plate Easy acces s or link plate Easy acces s only Easy acces s or link plate

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866)(630) 595-7868 TEL: (630) 766-5240 FAX: 466-9335
32
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

Ceiling Radiation Dampers

Technical Product Information

Ceiling Radiation Damper

Roll-formed 22-gauge galvanized frame Formed 22-gauge galvanized blades Roll-formed 22-gauge galvanized hinge (Model 50-4X has stainless steel spring hinge) Available in both easy access (EA) and link plate (LP) versions for mounting the fusible link (Model 50-4X available in EA only) Double-blade butterfly configuration (single-blade on Model 50-4X) Insulation and scrim are required on dampers over 80 in2 in area Insulation and scrim are optional on dampers less than 80 in2 in area Tested to UL 555C: File R16579 Meets NFPA 90A requirements Listed with California State Fire Marshall: Listing 3225-1577:101

50 Series - easy access Minimum unit size: 4" x 4" Maximum unit size: 24" x 24" Dimensions are determined by blade width (hinge dimension) then by blade height (W x H)

50 Series - with link plate Minimum unit size: 4" x 4" Maximum unit size: 24" x 24" Dimensions are determined by blade width (hinge dimension) then by blade height (W x H)

50-4X - easy access Available sizes: 8" x 4", 10" x 4" and 12" x 4" Dimensions are determined by blade length (hinge dimension) then by blade width

55 Series - easy access Minimum unit size: 4" diameter Maximum unit size: 24" diameter

55 Series - with link plate Minimum unit size: 4" diameter Maximum unit size: 24" diameter

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866) 466-9335
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

33

Ceiling Radiation Dampers

Technical Product Information

Ceiling Radiation Damper with Boot

UL-listed ceiling radiation damper factory mounted in a galvanized boot Available in the following styles: 90 boot End boot Straight boot Available with collars ranging from 4" to 10" Available with throat depths of 4", 6", and 8" Available with or without a flange Factory-assembled to ensure proper fit and placement Eliminates the need for labor to install in the field Single-blade damper not available in end boots with a 4" throat

50 Series - CRD with Boot

90 Boot End Boot

Straight Boot

Thermal Blanket and Scrim

Model CTB 24 (24" x 24" thermal blanket) Model CTB SCM 24 (24" x 24" scrim for attaching thermal blanket to damper) Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866)(630) 595-7868 TEL: (630) 766-5240 FAX: 466-9335
34
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

Condenser Support System

Technical Product Information

AC Bracket Mount
Mounts at any height Supports air conditioning units above ground level, regardless of the condition of the surrounding terrain Assemble and install the unit in minutes Constructed of heavy-duty steel Lightweight design provides a rated load capacity of 500 lbs. Eliminates the need for stand-ups or risers on heat pump applications and improves under-unit air circulation Helps control job completion variables on construction sites where the final grading needs to be done.

Sizes & Weights: No. 656090 Standard 36" L x 30" W, 17lbs. No. 656091 Medium 45" L x 36" W, 22 lbs. No. 656092 Large 55" L x 48" W, 25 lbs. Boxed: 1 Set per box Bulk: 50 Sets per pallet

Ward Industries 815 KIMBERLY DRIVE CAROL STREAM, IL 60188 TEL: (800) 624-8642 FAX: (866) 466-9335
Copyright, AUGUST, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved. All information is subject to change without notice. Dimensions and specifications shown are within manufacturing tolerances.

35

 Copyright, August, 2009, Commercial Products Group of Hart & Cooley, Inc. All Rights Reserved.