Digitally signed by

CHANDRESH KUMAR
Date: 2025.03.11 [Link] IST
 Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi
BILL OF QUANTITY

[Link] DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount
QTY DSR-2023 (Non-Schedule)

1 A Sub- Head I- Earthwork

1 2.6.1 Earth work in excavation by mechanical means (Hydraulic excavator) / manual cum 1428.39 177.50 253538.50 -
means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on
plan) including getting out and disposal of excavated earth, lead up to 50m and
for all lift ,as directed by Engineer-in-Charge. All kinds of soil.
2 [Link] Excavating trenches by mechinical / manual means of required width for pipes, cum 10.00 215.60 2156.00 -
cables, etc including excavation for sockets, and dressing of sides, ramming of
bottoms, for all depth, including getting out the excavated soil, and then
returning the soil as required, in layers not exceeding 20 cm in depth, including
consolidating each deposited layer by ramming, watering, etc. and disposing of
surplus excavated soil as directed, within a lead of 50 m :
All kinds of soil
Pipes, cables etc, not exceeding 80 mm dia.

3 2.22.1 Open timbering over areas including strutting, shoring etc. complete. sqm 241.94 44.85 10850.78 -
(Measurements to be taken of the face area timbered):
Depth not exceeding 1.5 m
4 2.22.2 Open timbering over areas including strutting, shoring etc. complete. sqm 241.94 54.95 13294.33 -
(Measurements to be taken of the face area timbered):
Depth exceeding 1.5 m but not exceeding 3 m
5 2.22.3 Open timbering over areas including strutting, shoring etc. complete. sqm 241.94 71.30 17249.97 -
(Measurements to be taken of the face area timbered):
Depth exceeding 3 m but not exceeding 4.5 m
6 2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of cum 1722.38 196.00 337586.45 -
foundations etc. in layers not exceeding 20cm in depth, consolidating each
deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

7 2.26.1 Extra for every additional lift of 1.5 m or part thereof in excavation /banking cum 1540.99 126.80 195398.15 -
excavated or stacked materials. All kinds of soil
8 2.27 Supplying and filling in plinth with sand under floors, including watering, cum 77.94 2123.75 165525.08 -
ramming,
consolidating and dressing complete.
9 2.31 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees Sqm 871.36 17.6 15335.91 -
and saplings of girth up to 30 cm measured at a height of 1 m above ground level
and removal of rubbish up to a distance of 50 m outside the periphery of the
area cleared.
10 2.34.1 Supplying chemical emulsion in sealed containers including delivery as specified: litre 425.05 234.75 99779.84 -
Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

11 [Link] Along the external wall below concrete or masonry apron using chemical sqm 765.09 53.45 40893.79 -
emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.:
With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

12 Sub-Head II - Concrete Work

13 4.1 Providing and laying in position cement concrete of specified grade excluding
the cost of centering and shuttering - All work up to plinth level :

14 4.1.3 [Link] (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm cum 5.31 7878.50 41818.29 -
nominal size)
15 4.15 [Link] (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 cum 14.04 7294.70 102417.59 -
graded stone aggregate 20 mm nominal size derived from natural sources)

16 [Link] Providing and laying in position ready mixed or site batched design mix cement cum 90.58 8835.15 800269.89 -
concrete for plain cement concrete work; using coarse aggregate and fine
aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland
/Portland Slag cement, admixtures in recommended proportions as per IS: 9103
to accelerate / retard setting of concrete, to improve durability and workability
without impairing strength; including pumping of concrete to site of laying,
curing, carriage for all leads; but excluding the cost of centering, shuttering and
finishing as per direction of the engineer-in-charge; for the following grades of
concrete.

Note: Extra cement up to 10% of the minimum specified cement content in

design mix shall be payable separately. In case the cement content in design mix
is more than 110% of the minimum specified cement content, the contractor
shall have discretion to either re-design the mix or bear the cost of extra
cement.
All works upto plinth level : Concrete of M10 grade with minimum cement
content of 220 kg /cum
17 4.2.3 Providing & laying cement concrete in retaining wall , return walls ( any Cum 11.88 9895.20 117554.98 -
thickness ) ,including attached pillasters,columns peirs, abuttments ,pillars ,posts
, struts, buttresses , string or lacing courses,parapets ,coping , bed blocks ,
anchor blocks,plain window sills,fillets , sunken floors,[Link] floor five level ,
excluding the cost of centring , shuttering & finishing.[Link] ( 1 cement :2 coarse
sand :4 stone aggregate20mm nominal size

18 Sub-Head- III- RCC Work -

19 5.3 Reinforced cement concrete work in beams, suspended floors, roofs having cum 8.64 11505.50 99407.52 -
slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window
sills, staircases and spiral stair cases above plinth level up to floor five level,
excluding the cost of centering, shuttering, finishing and reinforcement with
1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3
graded stone aggregate 20 mm nominal size derived from natural sources).

20 5.9 Centering and shuttering including strutting, propping etc. and removal of form -
for :
21 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete sqm 120.25 392.15 47155.65 -
22 5.9.2 Walls (any thickness) including attached pilasters, buttresses, plinth and string sqm 1370.46 842.50 1154609.18 -
courses etc.
23 5.9.3 Suspended floors, roofs, landings, balconies and access platform sqm 414.11 927.25 383981.48 -
24 5.9.4 Shelves (Cast in situ) Sqm 86.40 927.25 80114.40 -
25 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers. sqm 3008.69 736.40 2215597.11 -
26 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts sqm 1731.56 961.30 1664548.63 -
27 5.9.7 Stairs, (excluding landings) except spiral-staircases sqm 117.36 764.95 89774.53 -
28 5.9.14 Extra for shuttering in circular work (20% of respective sqm 583.69 185.45 108245.76 -
centering and shuttering items)
29 5.9.15 Small lintels not exceeding 1.5 m clear span, mouldings as in cornices, window Sqm 102.59 392.15 40228.71 -
sills, string courses, bands, copings, bed plates, anchor blocks and the like.

30 [Link] Edges of slabs and breaks in floors and walls Under 20 cm wide Rmt 844.20 208.55 176057.91 -
31 5.9.19 Weather shades, chajjas, corbels etc. including edges. Sqm 321.60 951.10 305873.76 -

Digitally signed by
CHANDRESH KUMAR
Date: 2025.03.11 [Link] IST
 Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi
BILL OF QUANTITY

[Link] DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount
QTY DSR-2023 (Non-Schedule)

32 5.9.20 Suspended floors, roofs, landings, balconies and access Sqm 2346.61 1028.40 2413254.73 -
platform with water proof ply 12 mm thick
33 5.22.6 Steel reinforcement for R.C.C. work including straightening, cutting, bending, kg 69300.64 107.85 7474073.92 -
placing in position and binding all complete upto plinth level. Thermo-
Mechanically Treated bars of grade Fe-500D or more.
34 5.22A.6 Steel reinforcement for R.C.C. work including straightening, cutting, bending, kg 141339.9 107.85 15243510.80 -
placing in position and binding all complete above plinth level. Thermo-
Mechanically Treated bars of grade Fe-500D or more.
35 5.30 Add for plaster drip course/ groove in plastered surface or moulding to metre 824.2 78.40 64614.14 -
R.C.C. projections.
36 5.33 Providing and laying in position ready mixed or site batched design mix cement -
concrete for reinforced cement concrete work; using coarse aggregate and fine
aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland
/Portland Slag cement, admixtures in recommended proportions as per IS: 9103
to accelerate / retard setting of concrete, to improve durability and workability
without impairing strength; including pumping of concrete to site of laying,
curing, carriage for all leads; but excluding the cost of centering, shuttering,
finishing and reinforcement as per direction of the engineer-in-charge; for the
following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement content in

design mix shall be payable separately. In case the cement content in design mix
is more than 110% of the specified minimum cement content, the contractor
shall have discretion to either re-design the mix or bear the cost of extra cement

37 5.33.1 All works upto plinth level.

38 [Link] Concrete of M25 grade with minimum cement content of 330 kg /cum. cum 644.31 9,504.75 6124008.13 -
39 [Link] Concrete of M30 grade with minimum cement content of 350 kg /cum cum 20.00 9,655.70 193114.00 -
40 5.33.2 All works above plinth level upto floor V level
41 [Link] Concrete of M25 grade with minimum cement content of 330 kg /cum cum 860.31 9,504.75 8176987.85 -
42 [Link] Concrete of M30 grade with minimum cement content of 350 kg /cum cum 20.00 9,655.70 193114.00 -
43 5.41.1 Supplying and applying pre tested and approved water based concrete sqm 6811.76 69.05 470351.71 -
curing compound to concrete/ masonry surface, all as per manufacturer’s
specification and direction of Engineer-in-charge
Non pigmented wet curing compound
44 5.35 Add for using extra cement in the items of design mix over and above quintal 509.72 733.50 373881.95 -
the specified cement content therein
45 Sub-Head- IV- Brick Work -
46 6.1.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class cum 20.00 7,132.50 142650.00 -
designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6
coarse sand)
47 6.4.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class cum 20.00 9,105.90 182118.00 -
designation 7.5 in superstructure above plinth level up to floor V level in all
shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)
48 6.34.2 Brick work with non modular fly ash bricks conforming to IS:12894, class cum 299.26 8,752.55 2619287.24 -
designation 10 average compressive strength in super structure above plinth
level up to floor V level in :Cement mortar 1:6 (1 cement : 6 Coarse sand)

49 6.45.2 Brick work with non modular fly ash bricks conforming to IS:12894, class sqm 1888.56 1105.80 2088369.65 -
designation 10 average compressive strength in super structure above plinth
level up to floor V level in :Cement mortar 1:6 (1 cement : 6 Coarse sand)

50 NS-1 Providing and fixing chicken wire mesh of 150 mm wide fixed with U nails 150 Rmt 1100.00 38.00 0.00 41,800.00
mm centre to centre before plastering between junctions of column/beam and
walls
51 Sub-Head- V- Stone work
52 7.32.2 Stone work, plain in copings, cornices, string courses and plinth courses, upto 75 cum 3.76 107965.10 405446.06 -
mm thick in Cement mortar 1:6 (1 cement : 6 coarse sand), including pointing
with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture
of pigment matching the stone [Link] sand stone

53 [Link] Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and 0.00 -
prepolished, machine cut for kitchen platforms, vanity counters, window sills,
facias and similar locations of required size,approved shade, colour and texture
laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints
treated with white cement, mixed with matching pigment, epoxy touch ups,
including rubbing, curing, moulding and polishing to edges to give high gloss
finish etc. complete at all levels. Granite stone slab of colour black, cherry/Ruby
red or as approved by Engineer incharge

54 [Link] Area of slab upto 0.50 sqm sqm 74.81 5413.50 404956.87 -
55 [Link] Area of slab above 0.50 sqm sqm 79.14 5136.30 406486.78 -
56 8.4 Extra for fixing marble /granite stone, over and above corresponding basic item, metre 305.10 568.55 173464.61 -
in facia and drops of width upto 150 mm with epoxy resin based adhesive,
including cleaning etc. complete.
57 8.3.2 Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., metre 392.10 510.95 200343.50 -
including machine polishing to edge to give high gloss finish etc. complete as per
design approved by Engineer-in-Charge. Granite work

58 8.5 Extra for providing opening of required size & shape for wash basin/ kitchen sink Each 42.00 978.70 41105.40 -
in kitchen platform, vanity counter and similar location in marble/ Granite/ stone
work, including necessary holes for pillar taps etc. including moulding, rubbing
and polishing of cut edges etc. complete.

59 [Link] Providing & fixing Granite Stone (polished) work for wall lining over 12 mm thick Sqm 196.01 3860.00 756610.18 -
bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3
kg/sqm including pointing in white cement [Link] of any colour and
shade
60 Sub-Head- VII- Wood & PVC work
61 9.1.1 Providing wood work in frames of doors, windows, clerestory windows and cum 6.54 142949.70 934274.57 -
other frames, wrought framed and fixed in position with hold fast lugs or with
dash fasteners of required dia & length (hold fast lugs or dash fastener shall be
paid for separately). Second class teak wood
62 NS-2 Providing and fixing factory made Prelaminated Solid door shutter made of 0.00 -
HDHMR Board (High Density High Moisture Resistance) of BSL(Metallic )grade.
,with prefinished both side laminate including liping,cutting rebate, fixing over
frame with stainless steel butt hinges Rate should include Door hardware of
Stainless steel (316 Grade) Door Knob,Hinges ( 125 mm ),

63 NS-2.1 35 mm thick Sqm 119.07 5432.85 0.00 6,46,889.45

64 NS-2.2 30 mm thick Sqm 80.33 4764.20 0.00 3,82,684.37

Digitally signed by
CHANDRESH KUMAR
Date: 2025.03.11 [Link] IST
 Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi
BILL OF QUANTITY

[Link] DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount
QTY DSR-2023 (Non-Schedule)

66 9.71.1 Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) Each 324.00 129.85 42071.40 -
with stainless steel screws etc. complete : 125x64x2.50 mm

67 NS-3 Providing and fixing bright finished SS ASI 316 grade tower bolts with necessary Each 99.00 712.00 0.00 70,488.00
screws etc complete .300 x 10mm
68 NS-4 Providing and fixing bright finished SS ASI 316 grade tower bolts with necessary Each 12.00 1200.00 0.00 14,400.00
screws etc complete .600 x 10mm
69 NS-5 Providing and fixing bright finished SS-316 Grade 100 mm mortice latch and Nos. 99.00 3060.01 0.00 3,02,940.62
lock with 6 levers and a pair of lever handles with necessary screws etc.
complete (best make of approved quality).
70 NS-6 Providing and fixing SS (304) grade Double door buffer floor door stopper, ISI Each 99.00 386.75 0.00 38,287.76
marked, transparent or dyed to required colour and shade, with necessary
screws etc. comple [Link] rubber stopper
71 NS-7 Providing and fixing Pull Handle- H Type (304 Grade)Back to back over Each 24.00 5648.00 0.00 1,35,552.00
Glass/Wood Door with necessary SS screws of complete as per direction of
Engineer in charge 25 mm x450 mm
72 NS-8 Supply & installation of Frameless Glass Partion for Bath shower. The Suspended sqm 86.94 7217.42 0.00 6,27,482.64
System held with Glass connector of SS-316 Grade Steel of approved
manufacturer & glass panel should be 12 mm thick clear toughened glass held
together . The Glass connector to fixed 3 nos on Floor & 3 nos in side wall with
screws all complete to perform as per specification and approved drawings .The
rate shall include all fitting fixers nut bolts, washer. all complete. For the purpose
of payment, actual elevation area of Glass shall be measured.

73 NS-9 Providing and fixing stainless steel grade 316 180 degree door viewer -PC finish. each 14.00 999.00 0.00 13,986.00
with necessary stainless steel screws etc. complete as per the direction of
Engineer-In-Charge.
74 NS-10 Supplying, installation, testing and commissioning of Digital door locks in each 12.00 17658.00 0.00 2,11,896.00
SS304 corrosion free having 5-in-1 Access (Bio+Pin+Card+Key with Wi-Fi
in builts) features, low battery alarm, Auto/Manual/Privacy locking features ,
fMotice latch etc, compatible for door thickness of 35 mm - 60 mm

75 Sub-Head-VII- Steel Work -

76 10.4 Providing and fixing 1 mm thick M.S. sheet sliding-shutters, with frame and sqm 7.56 6566.20 49640.47 -
diagonal braces of 40 x40 x6 mm angle iron, 3 mm M.S. gusset plates at the
junctions and corners, 25 mm dia pulley, 40x40x6 mm angle and T- iron guide at
the top and bottom respectively, including applying a priming coat of approved
steel primer.
77 NS-11 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan each 178.00 220.65 0.00 39,275.70
clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet
with its top surface hacked for proper bonding, top lid shall be screwed into the
cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one
lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as
per standard drawing.
78 10.28 Providing and Fixing Stainless Steel (Grade 304) railing made of Hollow tubes, kg 3563.04 772.40 2752092.10 -
Channels, plates etc. including welding, grinding, buffing, polishing and making
curvature (wherever required) and fitting the same with necesarry stainless
steel nuts and bolts complete, i/c fixing the railing with necessary accessories
and stainless steel dash fasteners, stainless steel bolts etc. of required size, on
the top of the floor or the side of waist slab with suitable arrangement as per
approval of Engineer-in-charge (for payment purpose only weight of stainless
steel members shall be considered excluding fixing accessories such as nuts,
bolts, fasterners etc.
79 Sub-Head- VIII- Flooring -
80 11.26 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed sqm 721.47 1948.25 1405599.06 -
with grey cement slurry mixed with pigment to match the shade of the slab,
including rubbing and polishing complete with base of cement mortar 1 : 4 (1
cement : 4 coarse sand) :11.26.1 25 mm thick
81 11.27 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on sqm 2.86 2354.70 6725.02 -
12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed
with grey cement slurry mixed with pigment to match the shade of the slabs,
including rubbing and polishing complete.
82 11.55.1 Providing and laying flamed finish Granite stone flooring in required design and sqm 0.00 3186.70 0.00 -
patterns, in linear as well as curvilinear portions of the building all complete as
per the architectural drawings with 18 mm thick stone slab over 20 mm
(average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and
jointed with cement slurry and pointing with white cement slurry admixed with
pigment of matching shade including rubbing, curing and polishing etc. all
complete as specified and as directed by the Engineer-in-Charge : Flamed finish
granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

83 11.56.1 Providing and laying Polished Granite stone flooring in required design and Sqm 265.81 4481.30 1191169.87 -
patterns, in linear as well as curvilinear portions of the building all complete as
per the architectural drawings with 18 mm thick stone slab over 20 mm
(average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and
jointed with cement slurry and pointing with white cement slurry admixed with
pigment of matching shade including rubbing, curing and polishing etc. all
complete as specified and as directed by the Engineer-in-Charge.
Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

84 NS-12 Providing and fixing Ist quality Ceramic glazed wall tiles of size not less 600 x sqm 838.59 1700.00 0.00 14,25,608.10
1200 mm conforming to IS: 15622 (thickness to be specified by the
manufacturer), of approved make, in all colours, design & shades as approved
by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick
bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey
cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with
pigment of matching shade complete.

85 11.41A.2.3 Providing and laying Vitrified tiles in floor in different sizes (thickness to be sqm 1140.46 1728.80 1971623.96 -
specified by the manufacturer) with water absorption less than 0.08% and
conforming to IS:15622, of approved brand & manufacturer, in all colours and
shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing
with grey cement slurry @3.3 kg/sqm including grouting the joints with white
cement and matching pigments etc. The tiles must be cut with the zero chipping
diamond cutter only . Laying of tiles will be done with the notch trowel, plier,
wedge, clips of required thickness, leveling system and rubber mallet for placing
the tiles gently and easily.:
Glazed vitrified floor tiles polished finish of size of Tile 800 x 800 mm
86 11.41A.3.1 Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm sqm 407.83 1464.85 597412.71 -

Digitally signed by
CHANDRESH KUMAR
Date: 2025.03.11 [Link] IST
 Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi
BILL OF QUANTITY

[Link] DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount
QTY DSR-2023 (Non-Schedule)

87 11.46.3 Providing and laying Vitrified tiles in different sizes (thickness to be specified by sqm 98.74 1958.45 193369.52 -
manufacturer ), with water absorption less than 0.08 % and conforming to I.S.
15622, of approved make, in all colours & shade, in skirting, riser of steps, over
12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with
grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement
& matching pigments etc. complete. Size of Tile 800x800 mm

88 Sub-Head- IX- Roofing

89 12.21.1 Providing gola 75x75 mm in cement concrete [Link] (1 cement :2 coarse sand : 4 metre 166.39 305.15 50773.91 -
stone aggregate 10 mm and down gauge) including finishing with cement mortar
1:3 (1 cement : 3 fine sand) as per standard design In 75x75 mm deep chase

90 12.22 Making khurras 45x45 cm with average minimum thickness of 5 cm cement Each 16.00 298.25 4772.00 -
concrete [Link] (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm
nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm
cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement,
rounding the edges and making and finishing the outlet complete.

91 12.41.2 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes Rmt 298.40 377.40 112616.16 -
conforming to IS : 13592 Type A, including jointing with seal ring conforming to
IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed
pipes. 110 mm diameter
92 12.42 Providing and fixing on wall face unplasticised - PVC moulded fittings/ 0.00 0.00 -
accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592
Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm
gap for thermal expansion
93 12.42.3 Single tee with door 110 mm Each 16.00 234.15 3746.40 -
94 12.42.6 Shoe (Plain) 110 mm Each 16.00 131.85 2109.60 -
95 12.43.2 Providing and fixing unplasticised -PVC pipe clips of approved design to Each 152.00 371.30 56437.60 -
unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs,
screwed with M.S. screws of required length, including cutting brick work and
fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall
etc. complete. 110 mm

96 12.44 Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm Each 16.00 54.70 875.20 -
diameter and weighing not less than 440 grams.
97 12.31.1 12.31 Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling Sqm 162.00 1718.95 278469.90 -
up to a height of 5 m above floor level, over first class kail wood
strips 25x6 mm with 10 mm gap in between and reinforced with
rabbit wire mesh fixed to wooden frame (frame work to be paid
separately): Flat surfaces

98 12.59 Providing & fixing false ceiling at all height including providing & fixing of 0.00 -
framework made of special section, power pressed from M.S. sheets and
galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277
and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of
27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash
fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed
to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of
required size and other end of angle hanger fixed with intermediate G.I chanels
45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling
section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm
each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction
perpendicular to G.I intermediate channel with connecting clip made out of
2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter
channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the
perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at
450mm centre, with 25mm long dry wall screws @ 230mm interval, including
fixing of Calcium Silicate Board to ceiling section and perimeter channels with
the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing &
finishing to a flush finish of tapered and square edges of the board with
recommended jointing compounds, jointing tapes,finishing with jointing
compounds in three layers covering up to 150mm on both sides of joints and
two coats of primer suitable for boards, all as per manufacture's specification
and also including the cost of making opening for light fittings, grills, diffusers,
cut outs made with frame of perimeter channels suitably fixed, all complete as
per drawings, specificaton and direction of the Engineer in charge but excluding
the cost of painting with

99 12.59.1 :8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials Sqm 133.00 1572.30 209115.90 -
reinforced with cellulose fiber manufactured through autoclaving process.

100 12.52 Providing and fixing tiled false ceiling of approved materials of size 595x595 mm 0.00 -
in true horizontal level, suspended on inter locking metal grid of hot dipped
galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive)
consisting of main “T” runner with suitably spaced joints to get required length
and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at
1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm
thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm
center to center to form a grid of 1200x600 mm and secondary cross “T” of
length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to
be interlocked at middle of the 1200x600 mm panel to form grids of 600x600
mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of
approved texture in the grid including, required cutting/making, opening for
services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T”
runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25
x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm
GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm
spaced at 1200 mm center to center along main T, bottom exposed width of 24
mm of all T-sections shall be pre-painted with polyester paint, all complete for
all heights as per specifications, drawings and as directed by Engineer-in-charge

101 12.52.1 GI Metal Ceiling Lay in plain Tegular edge Global white colour tiles of size Sqm 181.13 1902.95 344671.82 -
595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having
galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester
powder coated of thickness 60 microns (minimum), including factory painted
after bending.
102 Sub-Head-X- Finishing
103 13.4.2 12 mm cement plaster of mix : :6 (1 cement: 6 coarse sand) sqm 6472.61 343.65 2224312.43 -

Digitally signed by
CHANDRESH KUMAR
Date: 2025.03.11 [Link] IST
 Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi
BILL OF QUANTITY

[Link] DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount
QTY DSR-2023 (Non-Schedule)

104 13.5.2 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 sqm 2817.01 395.35 1113704.31 -
(1 cement: 6 coarse sand)
105 13.16.1 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) sqm 2760.72 300.45 829457.96 -
106 13.80 Providing and applying white cement based putty of average thickness 1 mm, of sqm 10078.57 156.05 1572761.00 -
approved brand and manufacturer, over the plastered wall surface to prepare
the surface even and smooth complete.
107 13.83.2 Wall painting with premium acrylic emulsion paint of interior grade, having VOC sqm 4137.91 142.80 590893.19 -
(Volatile Organic Compound ) content less than 50 grams/ litre of approved
brand and manufacture, including applying additional coats wherever required
to achieve even shade and colou r Two coats
108 13.85.3 Applying priming coats with primer of approved brand and manufacture, having sqm 769.95 73.95 56937.99 -
low VOC (Volatile Organic Compound ) content With water thinnable cement
primer on wall surface having VOC content less than 50 grams/litre

109 NS-13 Painting with acrylic emulsion paint of Stucco Marble satin finish and sqm 1941.78 1050.00 0.00 20,38,872.15
manufacture to give an even shade to wall and ceiling etc. applied evenly with
roller to give approved matt or stippled finish complete, including cleaning
preparation , putting etc. over coat of cement primer of surface and coat of
approved primer as per manufacturer’s specification:Two or more coats on new
work/and old work including scraping of old paint and disposal of mulba to
authorized dumping grounds.( for old and new work including peeling/removing
old paint. ) FOR ROOMS CEILING, TOILET, KITCHEN & CORRIDOR WALLS/CEILING

110 13.62.1 Painting with synthetic enamel paint of approved brand and manufacture to sqm 553.30 226.25 125183.77 -
give an even shade : Two or more coats on new work
111 13.48.1 Finishing walls with textured exterior paint of required shade : 13.45.1 New sqm 1645.46 223.60 367924.86 -
work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming
coat of exterior primer applied @ 2.20kg/10 sqm
112 Road Work
113 16.75 Providing and laying C.C. pavement of mix M-25 with ready mixed concrete cum 85.80 9823.80 842882.04 -
from batching plant. The ready mixed concrete shall be laid and finished
with screed board vibrator , vacuum dewatering process and finally finished
by floating, brooming with wire brush etc. complete as per specifications
and directions of Engineer-in-charge. (The panel shuttering work shall be
paid for separately).
(Note:- Cement content considered in this item is @ 330 kg/cum. Excess/
less cement used as per design mix is payable/ recoverable separately).

114 Sub-Head -XI - Aluminum & UPVC Work

115 9.147.A Providing and fixing factory made uPVC glazed/wire mesh windows/ doors 0.00 -
comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler
(where ever required) extruded profiles having minimum wall thickness of 1.70
mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles
conforming to EN: 12608 in any shape, colour and design dully reinforced with
galvanized mild steel section made of required shape & size as per CPWD
Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor
(where ever required) of appropriate dimension, EPDM gasket, hardware, SS
304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of
matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS
1367: Part 1 to 14, plastic packers, plastic caps and necessary stainless steel
screws etc. Profile of frame, sash & multion (if required) shall be mitred cut and
fusion welded /mechanically jointed duly sealed at all comers, including driling
of holes for fixing hardware and drainage of water etc. After fixing frame the gap
between frame and adjacent finished wall shall be filled with weather proof
silicon sealant over backer rod of approved size and quality all complete as per
approved drawing conforming to CPWD specification & direction of Engineer-in-
Charge, Section of steel reinforcement and cross sections of PVC profiles to be
as per design approved by Engineer-in-Charge. Wire mesh Glazing of plan
toughened Laminated double glass unit with/without high performance coatings
sans per design requirements and conforming to 19 3545 & 15 16231 shall be
paid separately, Note Structural design proof checked from a Government
Engrweing Institute to be provided by the manufacturer for tites wat base wet
speed 45 sec as per 15 8/70- Part 3 on Sites with structure herges more than
20m for a wind speeds

116 9.147.C1.1 Fixed window/ventilator without mullion/[Link] R1 series with frame Sqm 21.06 8247.25 1,73,687.09 -
(33 mm & above) x 135 mm & above). (Height upto 0.90 metre)
117 9.147.A4.1 Three track three panels sliding window with two glazed & one wire mesh Sqm 247.37 10993.55 27,19,419.50 -
panels with Aluminium channel for roller track, wool pile, nylon rollers with SS
304 body. Using R2 series with frame (70 mm & above) x (40 mm & above) &
both glazed and fly screen sash (25 mm & above) x (50 mm & above) with zinc
alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 metre)

118 9.147.B1.1 Two track two panels sliding door with Aluminium channel for roller track, wool Sqm 89.78 8106.30 7,27,743.08 -
pile, zinc alloy (zamak) powder coated handle on every panel along with multi-
point locking system, adjustable nylon rollers with SS 304 body. Using R3 series
with frame (55 mm & above) x (40 mm & above) & sash (30 mm & above) x (74
mm & above). (Height upto 2.5 metre).

119 21.3 Providing and fixing glazing in PVC / aluminum door, window, ventilator shutters - -
and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the
architectural drawings and the directions of engineerin- charge. (Cost of
aluminum snap beading shall be paid in basic item.)

120 21.3.2 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) sqm 233.15 1505.25 3,50,941.51 -

121 21.3.3 With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm) sqm 67.33 1685.40 1,13,480.09 -

122 9.15 Providing and fixing zinc alloyed (white powder coated) touch lock for uPVC Each 147.00 115.80 17,022.60 -
sliding window with necessary screws etc. complete.
123 9.15 Providing and fixing steel roller for uPVC sliding window with necessary screws Each 162.00 185.50 30,051.00 -
etc. complete
124 9.135.2 Providing and fixing fly proof stainless steel grade 304 wire gauge, to Each 105.11 1228.00 1,29,077.00 -
windows and clerestory windows using wire gauge with average width
of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all
complete. With 12 mm mild steel U beading

Digitally signed by
CHANDRESH KUMAR
Date: 2025.03.11 [Link] IST
 Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi
BILL OF QUANTITY

[Link] DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount
QTY DSR-2023 (Non-Schedule)

125 NS-14 Providing and fixing 19mm dia Stainless Steel drapery rod in required shade Rmt 228.35 1754.20 - 4,00,562.80
including rings, @ 100mm C/C, brackets, finial i.c fixing with necessary SS screws
and PVC sleeve etc. complete as per direction of Engineer in charge.

126 Sub-Head-XIII- Water Proofing

127 NS-15 Supplying and installing 1.5 mm composite thick fully bonded weldable HDPE sqm 634.44 1515.60 - 9,61,553.48
membrane conforming to IS 16471:2017 requirements of UG waterproofing
structures, requirements to provide Type A fully bonded protection of UG
waterproofing structures. The membrane shall exhibit 25 years of service life
tested and complied in accordance with EN 13251:2016 durability certification.
The membrane should be minimum 2.4 m wide comprising of an HDPE layer and
a
pressure sensitive adhesive layer which is covered by a weatherproof protective
layer with lap Joint Strength at overlaps >15000 N/m ASTM D 1876. The
membrane shall have minimum of 100mm side and end laps which shall be
thermofused with leister machines at all the joints for assuring watertightness
and achieving monolithic membrane. End laps and side laps should be a
minimum of 100 mm with the weld size of minimum 50 mm in case of a single
weld system. In case of a double weld system, comprising of two parallel welds
of 15 mm wide each with a 20 mm air channel gap in between the two weld
[Link] size of the membrane should not be less than 2.4 Mtr. x 20 Mtr. to
minimize the joints. This membrane shall be continued over the vertical surface
but terminated minimum 100mm below the top edge of the raft slab/footings
and fixed as per recommendation. Basic Propoerties are as follows:
1. Thickness of complosite memberane 1.5 mm
2. Tensile strength 25 mpa
3. Elongation 500%
4. Low temperature flexibility -25 Degree
5. Hydrostatic head resistance 70 m
6. Peel to concrete adhesion 1500 N/m
7. Lap Joint (side and end laps) peel adehesion 15000 N/m
8. Puncture rsistance 1000N

128 NS-16 Providing & applying 2 components, solvent free, liquid applied elastomeric sqm 503.74 2500.00 - 12,59,348.75
seamless hybrid Polyurea Polyurethane Membrane, using high pressure plural
component spray equipment, to form a minimum system thickness of 1.5 mm in
two or more passes with a total consumption of 1.5-1.6 kg / m2. The membrane
should have 100% Solids, VOC Free, Tensile strength 15 Mpa as per ASTM D 412,
Elongation 450% as per ASTM D 412, Low temperature Crack bridging ability of
3.2mm as per ASTM C 1305, Shore A Hardness 85 ASTM D 2240, Puncture
Resistance 1000 N as per ASTM E 154, Water Head Resistance 7 Bar as per
ASTM D [Link] coating should pass Dynamic Crack Bridging as per EN 1062-7,
Method B for 20,000 cycles at -20 degree temperature. The membrane should
exhibit 25 years of service life tested and complied in accordance with EN
13251:2016 durability certification. Apply primer coat of epoxy primer by roller/
airless spray guideline and coverage @ 5-6 m2/ltr depends on porosity
of concrete. Allow to cure for max 5-6 hours. Broadcast anti slip grains of 200-300
micron (dried sand) on wet primer at coverage of 0.8-1 kg/m2 and allow to come
to touch dry condition before application of Membrane.

129 NS-17 Providing and fixing water profing treatment in Bath room/ toilet Providing and sqm 205.38 967.39 - 1,98,683.15
applying High Performance Two Component Acrylic Polymer Modified
Cementitious flexible flexible waterproofing, Dr. Fixit Fastflex having film build
up of 1.2mm to 1.5mm with elongation upto 120%. Applying coating in two
coats @1.0 kg/ M2/ coat in the time interval of 6-8 hrs. Coating shall be done on
the entire horizontal surface and vertical surface upto 7 ft from FFL adjust walls
of shower. (Rest upto 1ft.) After 2nd coat fine washed sand is sprinkeled on
Vertical wall while the coat is tacky for key to succesive plaster or screed. Note :
1st coat must be applied on damp (SSD) surface not on dry surface. (Cement,
sand, electricity, water and other civil products should be supplied by civil
contractor for free of cost).Water Ponding Test : After 2nd Coat allow these
coating to cure for 7 Days as per curing process given in TDS. Check coating for
any damage or cracks during 7 days of curing. If found repair it. Cure it. Conduct
Water Ponding [Link] all the outlets properly by suitable means. Fill the
water minimum up to 50mm [Link] this water for maximum 48
[Link] the leakage or dampness on other side. If No dampness observed
carry out further process of applying protective screed, tiling etc. once the
coating is totally [Link] : If no water ponding test, then plaster or screed can
be done after 72 Hrs of final coat by authorised by company with due tto
certified

130 NS-18 Providing & applying PU based high performance waterproofing treatment over Sqm 936.44 1806.75 - 16,91,911.50
terrace having pure polyurethane based, single component, low VOC,
elastomeric, seamless, moisture curing, waterproof membrane, Dr. Fixit FlexiPU
270(I), applied in 2 coats over After carrying the necessary preparation with
roller at a total consumption of 1.5 Kgs/Sqmt, having specific gravity of
minimum 1.30, having an elongation capacity of over 400%, with tensile strength
of > 2.00Mpa, Adhesion to concrete surface over 2.00N/mm2, Shore A Hardness
of 75, Fire resistance EURO Class-F, with Anti-root propertise, with a service
temperature range of -40deg C to 80deg C, with solids content of around 90%,
to be applied by brush/roller over the RCC slab and on the vertical surfaces upto
300mm above FFL, thereafter ponding with water for 3 days etc. complete. The
work shall be carried out all complete as per specification and the direction of
the engineer-in-charge. The product performance shall carry guaranteed for 10
years against any leakage

131 22.14.1 Grading roof for water proofing treatment with Cement concrete [Link] (1 cum 61.94 7510.75 4,65,244.02 -
cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
132 TERRACE GARDEN -
133 2.2 Supplying and stacking of good earth at site including royalty and carriage cum 93.64 469.50 43,965.86 -
up to 1 km (earth measured in stacks will be reduced by 20% for payment).

Digitally signed by
CHANDRESH KUMAR
Date: 2025.03.11 [Link] IST
 Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi
BILL OF QUANTITY

[Link] DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount
QTY DSR-2023 (Non-Schedule)

134 2.4.1 Supplying and stacking at site dump manure from approved source, cum 70.23 229.95 16,150.08 -
including carriage (manure measured in stacks will be reduced by 8% for
payment) : Screened through sieve of I.S. designation 20 mm

135 2.3 Supplying and stacking at site sludge from approved source, including cum 70.23 276.90 19,447.52 -
carriage (manure measured in stacks will be reduced by 8% for payment) :

136 2.8 Spreading of sludge, dump manure or/and good earth in equired thickness cum 234.11 46.15 10,804.18 -
(Cost of sludge, dump manure or/ and good earth to be paid separately).

137 2.9 Mixing earth and sludge and manure in proportion specified or as directed. cum 234.11 32.10 7,514.93 -

138 NS-19 Grassing with Selected type of I grass at Terrace in following stages: sqm 702.33 423.00 - 2,97,085.59
Stage-1:Providing & Laying of 13 mm thick Light Weight , high strength,Hi -
Impact Polypropylene modular drainage cells which is to be especially
designed for sub surface Drainage and Water Proofing Membrane
Protection.
Stage-2 : Providing and Laying of Non -woven Geo Textile 150 gsm over
the Drainage Cells. Stage-3 :Supplying & Laying of Coco-pit Layer (
minimum 20 mm thick )
Stage-4:Grasing with Selected type of grass as approved by the Architect
including watering and maintenance of the Terrace lawn for 30 days or
more till the grass forms a thick lawn free from weeds.

139 2.5 Providing & fixing of White River (Stone) Pables size of 2" to 2.50" dia in Qtl 10.00 2400 24,000.00 -
natural colour at site of work including loading, unloading, carriage and all
taxes paid [Link] as per direction of officer in charge.

140 SANITARY FIXTURES

141 NS-20 Supply, Installation and commissioning approved make wash down wall 42.00 16914.00 - 7,10,388.00
mounted EWC conforming to IS:2556 (Part 16)-2002 with 'P' or 'S' trap
with concealed flush cistern fixed in wall(Viega Concealed Cistern with
Chrome Flush Plate with Press panel including, ultra solid seat cover of
approved make with rubber buffer and cap all of approved make etc.
complete for finished item of work in all respects Size : 515 x 350 x 330
mm [Link]. ( AV-2966 ) of Acquaviva or equivalent Make:
KOHLER,GROHE Each
142 17.1.2 2.00 5781.35 11,562.70 -
Providing and fixing water closet squatting pan (Indian type W.C. pan ) with
100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing
cistern, including flush pipe, with manually controlled device (handle lever)
conforming to IS : 7231, with all fittings and fixtures complete, including
cutting and making good the walls and floors wherever required:White
Vitreous china Orissa pattern W.C. pan of size
580x440 mm with integral type foot rests Each
143 NS-21 Providing and fixing wash basin with fixing arrangement, including C.P. 42.00 4198.00 - 1,76,316.00
brass waste of standard pattern, including painting of fittings and brackets,
cutting and making good the walls wherever require: Over the Counter
Wash basin of size 440 x 440 x 100,[Link]. ( AQV 76232 ) of
Acquaviva or equivalent KOHLER,GROHE Each
144 17.7A Providing and fixing wash basin with C.I. brackets, 15 mm dia CP 2.00 3960.55 7,921.10 -
Brass single hole basin mixer of approved quality and make, including
painting of fittings and brackets, cutting and making good the walls
wherever required:- (a) White Vitreous China Wash basin size 550x400
mm with a 15 mm CP Brass single hole basin mixer
Each
145 NS-22 Providing & fixing premium make SENSOR TAP DECK MOUNT SHORT 42.00 10465.00 - 4,39,530.00
BODY for wash basin, and with 10 years warranty l as per manufacturers
specification and direction of Engineer-in-
[Link])[Link]. (SF 7020, ,Acquaviva make ) Make:
Acquaviva or equivalent KOHLER,GROHE Each
146 NS-23 Providing and fixing Braided hose with Two 15mm Nuts & Rubber washers 42.00 501.00 - 21,042.00
without Nipple 6021Waste Coupling 32mm Full Thread : Model No.
BDC001 of Aquaviva make 45 cm length KOHLER,GROHE
Each
147 NS-24 Providing and fixing Wall mounted Bathroom shaving Mirror 8"with 42.00 2818.00 - 1,18,356.00
expandle/adjustable : Model No. MIR-1855 of Acquaviva or equivalent
[Link],GROHE, Acquaviva Each
148 NS-25 Providing and fixing C.P. Brass 2864 Bib Tap Long Body Chrome Finish as 42.00 615.00 - 25,830.00
per model no. 2864 of jaquar or equvilent for wash basin.
(Make:Acquaviva, ).KOHLER,GROHE, Acquaviva Each
149 [Link] Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 12.00 6945.60 83,347.20 -
with C.I. brackets and stainless steel plug 40 mm, including painting of fittings
and brackets, cutting and making good the walls wherever required :Kitchen sink
with drain board 510x1040 mm bowl depth 250 mm MAKE
(Kingstone/Nirali/Corrysil) Each
150 NS-26 Supplying, installing, testing and commissioning approved make 15mm CP 42.00 2875.00 - 1,20,750.00
health faucet with CP flexible tube 1.2 m long and wall hook (model no. HF 1812
Acquaviva make )- having High Quality plating in compliance with DIN and EN
standards including CP crutch, nozzle & 2 way Bib Cock with wall flange
etc.,complete. HF-1812 MAKES AQUAVIVA, KOHLER,GROHE

Each
152 NS-27 Providing and fixing C.P. Brass divertor consisting concealed body and 42.00 8650.00 - 3,63,300.00
other parts as per model no. ALD055 ,Exposed parts kit consisting
operating lever wall flang as per model OPL-15065K and one spout (Model
AD-114 ,Acquaviva make) Including Concealed Part Make:
Acquaviva/Toto/Grohe Each
153 NS-28 Providing and fixing SS AISI-316 Grade Toilet Paper Holder with Flap 42.00 1903.00 - 79,926.00
complete with brackets fixed with CP brass screws PVC sleeves etc.
Complete: 155 mm long .Model No- TTPHF , of KICH, or
equivalent.(Make: Kich/Jaquar/Roca/ Cera/ Arch/ D-Line) Each
154 NS-29 Providing & fixing cockcroch trap S.S. grating of approved design for floor traps 102.00 558.00 - 56,916.00
etc. including setting in floor with cement mortar. 100 mm dia (Make:
Kich/Jaquar/Roca/ Cera/ Arch/ D-Line) each
155 18.50.1 Providing and fixing C.P. brass long nose bib cock of approved quality 84.00 820.70 68,938.80 -
conforming to IS standards and weighing not less than 810 gms.15 mm nominal
bore Each
156 18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of 84.00 574.30 48,241.20 -
approved quality conforming to IS:8931 15mm nominal bore Each
157 17.22A Providing and fixing CP Brass 32mm size Bottle Trap Model No 5001 Aquaviva of 42.00 1034.80 43,461.60 -
approved quality & make and as per the direction of Engineer-in-charge
Each

Digitally signed by
CHANDRESH KUMAR
Date: 2025.03.11 [Link] IST
 Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi
BILL OF QUANTITY

[Link] DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount
QTY DSR-2023 (Non-Schedule)

158 NS-30 Providing and fixing SS AISI-316 Grade Towel rail complete with brackets fixed 42.00 1104.00 - 46,368.00
with CP brass screws PVC sleeves etc. Complete: 650 mm long .Model No- SDA-
060, of Acquaviva or equivalent,,(Make: Kich/Jaquar/Roca/ Cera/Grohe/ Arch/ D-
Line) each
159 NS-31 Providing and fixing 600x120x5 mm Corner Soap Dish glass shelf with 42.00 1782.50 - 74,865.00
edges round off, supported on SS angle frame with C.P. brass brackets
and guard rail complete fixed with 40 mm long screws, rawl plugs
[Link] No- SDA-056 of Acquaviva or equivalent Each
160 17.28.2 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. 12.00 119.55 1,434.60 -
waste fittings [Link] pipe Each
161 NS-32 Supplying & Fixing of SS AISI-316 Liquid Soap Dispenser(Round Shape) 42.00 1895.00 - 79,590.00
200 ml capacity fixed to the wall with PVC rubber plug with CP brass
screws Model No- TLSD2S of KICH, or equivalent (Make:
Kich/Jaquar/Roca/ Arch/ D-Line) Each
162 17.31 Providing and fixing 600x450 mm beveled edge mirror of superior nglass (of 42.00 1607.95 67,533.90 -
approved quality) complete with 6 mm thick hard board ground fixed to wooden
cleats with C.P. brass screws and washers complete.
Each
163 NS-33 Providing & fixing cockcroch trap S.S. grating of approved design for floor traps 42.00 558.00 - 23,436.00
etc. including setting in floor with cement mortar. 100 mm dia
Each
164 NS-34 Providing and fixing C.P Round Ceiling Mounted Shower of size 250 x 250 mm 42.00 5551.00 - 2,33,142.00
mm Single Flow with Rubit Cleaning System including, shower arm dia 20 mm &
450 mm Long round shape with Straight for ceiling mounted showers (Mode no:
RSs-1654 , Make Acquaviva .) (Make: Acquaviva /Xen/kingston
Each
165 WATER SUPPLY
166 18.70 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal
stability for hot and cold water supply, including all CPVC plain and brass
threaded fittings. This includes jointing of pipes and fittings with one step CPVC
solvent cement and testing of joints complete as per direction of Engineer-in-
charge
167 Internal work-exposed on wall, including fixing the pipewith clamps at 1.00
meter spacing
168 18.7.3 25mm nominal outer dia pipes. Rmt 774.75 401.55 3,11,100.86 -
169 18.7.4 32mm nominal outer dia pipes Rmt 776.55 518.75 4,02,835.31 -
170 18.7.5 40mm nominal outer dia pipes. Rmt 259.50 702.95 1,82,415.53 -
171 18.7.6 External work including trenching, refilling etc.50mm nominal outer dia pipes. 396.00 934.15 3,69,923.40 -
Rmt
172 18.8.1 Internal work Concealed fixing the pipe with clamps at 1701.75 497.80 8,47,131.15 -
1.00 meter spacing including cutting chases and making good the wall etc.15mm
nominal outer dia pipes. Metre
173 18.17 Providing material and labour for fixing gun metal gate valve with C.I. wheel of 0.00 - -
approved quality (screwed end) :
174 18.17.1 25 mm nominal bore Each 51.00 622.40 31,742.40 -
175 18.17.3 40 mm nominal bore Each 33.00 826.10 27,261.30 -
176 18.18.3 Supplying & fixing of 25 mm dia Ball brass valves, high pressure, with polythene 67.50 464.05 31,323.38 -
float and flynut complete, screwed for iron pipe or brass ferrule and fixed
Each
177 18.48 Providing material and labour for placing on terrace (at all floor levels) superior 18000.00 16.00 2,88,000.00 -
qualtity water storage tanks under the brand name SINTEX manufactured using
superior quality virgin raw material with four layer design in approved colours
including the ISI variety in black colour. The four layered thermally insulated
water tanks should be designed using the foam layer to minimize the effects of
sunlight & water cool in summers with cover . The rate shall including suitable
locking arrangement and making necessary holes for inlet, outlet and overflow
pipes but without fittings and the base support for tank
Ltr
178 SOIL & WASTE PIPE & FITTINGS
179 NS-35 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes fittings 497.90 521.00 - 2,59,405.90
type B for sewerage waste discharge system (IS:13592 : 1992 Marked) of
approved quality /make supreme, jain pipes, sudhakar, prince or equivalent 100
mm Rmt
180 NS-36 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes fittings 630.70 378.00 - 2,38,404.60
type B for sewerage waste discharge system (IS:13592 : 1992 Marked) of
approved quality /make supreme, jain pipes, sudhakar, prince or equivalent 75
mm Rmt
181 NS-37 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes fittings 0.00 - -
type B for sewarage waste discharge system (IS:13592 : 1992 Marked) of
approved quality /make
182 Bend of required degree with access door, 0.00 - -
183 NS-37.1 100 mm dia Each 166.00 356.00 - 59,096.00
184 NS-37.2 75 mm dia Each 171.00 251.00 - 42,921.00
185 NS-38 Plain bend of required degree. 0.00 - -
186 NS-38.1 100 mm dia Each 158.00 707.01 - 1,11,707.67
187 NS-38.2 75 mm dia Each 177.00 416.93 - 73,796.87
188 NS-39 Heel rest sanitary bend 0.00 - -
189 NS-39.1 100 mm dia Each 45.00 584.87 - 26,319.02
190 0.00 - -
191 [Link] Providing and fixing single equal plain junction of required degree :75x75x75 0.00 - -
mmSand cast iron S&S as per IS - 3989
192 75x75x75 mm Each 89.00 561.20 49,946.80 -
193 EXTERNAL DRAINAGE
194 [Link] Providing and fixing square-mouth S.W. gully trap grade‘A’ complete with C.I. 19.00 2711.70 51,522.30 -
grating, brick masonry chamber with water tight C.I. cover with frame of 300
x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame
to be not less than 2.70 kg as per standard design 150 x 100 mm size P type With
Sewer bricks conforming to IS : 4885
Sqm
195 [Link] Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse 8.00 12770.55 1,02,164.40 -
sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III)
: 3 graded stone aggregate 20 mm nominal size), foundation concrete [Link] mix
(1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal
size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse
sand) finished with floating coat of neat cement and making channels in cement
concrete [Link] (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm
nominal size) finished with a floating coat of neat cement complete as per
standard design :Inside size 90x80 cm and 45 cm deep including C.I. cover with
frame (light duty) 455x610 mm internal dimensions, total weight of cover and
frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15
kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Each

Digitally signed by
CHANDRESH KUMAR
Date: 2025.03.11 [Link] IST
 Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi
BILL OF QUANTITY

[Link] DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount
QTY DSR-2023 (Non-Schedule)

196 19.60 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars 0.00 - -
jointed with stiff mixture of cement mortar in the proportion of 1;2 (1 cement : 2
fine sand) including testing of joints etc. complete:

197 19.6.2 150 mm dia. R.C.C. pipe Metre 188.00 556.45 1,04,612.60 -
198 19.6.3 250 mm dia. R.C.C. pipe Metre 81.00 899.80 72,883.80 -
199 19.20 Providing and laying cement concrete [Link] (1 cement : 5 coarse sand : 10 0.00 - -
graded stone aggregate 40 mm nominal size) all-round SW/ RCC pipes including
bed concrete as per standard design:
200 19.2.2 150 mm diameter SW/RCC pipe Metre 188.00 1179.85 2,21,811.80 -
201 19.2.4 250 mm diameter SW/RCC pipe Metre 81.00 1590.55 1,28,834.55 -
202 19.27.1 Constructing brick masonry road gully chamber 50X45X60 cm with brick of class 12.00 5957.90 71,494.80 -
designation 75 in cement mortar 1:4 (1 cement : 4 coarse sand) including
500*450 mm pre-cast R.C.C. horizontal grating with frame complete as per
standard design: With F.P.S. bricks Each
203 BOREWELL
204 18.42.3 Boring with 100 mm diameter casing pipe for hand pump / tubewell, in all soils meter 57.00 1025.95 58,479.15 -
except ordinary hard rocks requiring blasting, including removing the casing pipe
after the hand pump / tube well is lowered and tested :Beyond 12 m and up to
18 m depth
205 18.43 Providing and placing in position filters of 40 mm diameter G.I. pipe with brass meter 57.00 960.30 54,737.10 -
strainer of approved quality.
206 NS-40 Providing and erecting ISI marked PVC insulated PVC Shethed Flat flexible meter 116.00 110.00 - 12,760.00
Submercible copper cable approved make of following Size. (b) 3 Core x 2.5 Sq.
mm.
207 NS-41 Supplying and erecting Kirloskar 1 HP single Phase 100 mm Borewell Nos 2.00 13475.01 - 26,950.02
Submersible Monobloc Pump, KDS 128+, 1 HP, Single Phase, 210 Volts, Size
32mm X 25mm MOTOR bearing ISI mark and manufacture as per IS 8034/1989
to give the run for pumpset and motor for two hours and one year guarantee
alongwith ISI certificate including cost of all necessary accessories with starter
and 32 mm dia outlet connection etc. complete. Kirloskar or equivalent

208 Furniture
209 NS-42 Description:- Pantry cabinetry lower carcass-upplying, and placing in position of sqft 1000.00 2948.00 - 29,48,000.00
pantry cabinets as per design approved and space avilable. a) Bottom carcass:
made of 18mm thick Marine or equivalent ply with both side pasted with 0.8
mm thick laminate of fabric or jute light colour as per approval of engineer
incharge. Exposed edges to be wrapped with machine glued only edge banding
tape of matching colours. Thickness of tape shall not be less than 0.8 mm with
proper edging and trimming of the corners. Back ply to be made in 6mm thick
ply of Marine quality with the same lining laminate of 0.8 mm thick of same
colour and texture as of boxes material. This ply shall be secured in the box with
groove method and no screws are used to fix the ply. All ply boxes to be fixed
with rust proof screws only. No nails shall be used to fix the boxes. Size of
carcass D560x700H. length to be determined as per site. b) Shutters to be made
with Merino or equialent high gloss meister finish or Merino high gloss finish 1
mm thick laminate/ high gloss acrylic with 2mm thick edge banding tape of same
colour as of front colour, with bak laminate to be matching to carcass shade
laminate. Size shall vary as per requirement of design approval. all shutter to be
used with C type profile or j profile matching colour to the cabinet shutters. c) All
drawers hardware shall be innotech type with different uses like crockerey,
cutlery, atta rack, multipurpose drawersm end carrousel brands, G,T,P,T, brands
like Hettich, Haffle, Grass, Blum. A maximum of 10 nos in one pantry unit
combined. d) All hinges used shall be auto stop soft closing hinges for both
upper and lower shutters of the approved brands brands like hettich, Haffle,
Grass, Blum. Rates per square feetSink area to be speacially made to
50x50x3mm thick aluminium frame with 18mm thick WPC board of high density
only of approved brand shall be used to make the box of sink. Garbage bin shall
be provided inside sink area. e) Additional 18mm thick WPC board to be used
after all lower boxes or carcasses are fixed in position and screwed to them with
rust free screws. f) Sink area to be specially made to 50*50*3mm thick
aluminum frame with 18 mm thick WPC board of high density only of approved
brand shall be used to make the box of sink. Garbage bin shall be provided inside
sink area. Cutting of space for sink, final size as per engineer incharge. g)
210 NS-43 Description:- Pantry Cabinetry Upper carecass-Upper Carcass: storage above sqft 580.000 2400.00 13,92,000.00
cove counter: Shall be made of 18mm thick marine ply with both side pasted
with 0.8 mm thick laminate of fabric or jute light colour as per approval of
engineer incharge. Shutters to be made with merino or equivalent high gloss
mister finish or Merino high gloss finish 1mm thick laminate/ high gloss acrylic
with 2mm thick edge banding tape of same colour as of front colour, with back
laminate to be matching to carcass shade laminate. Size shall vary as per
requirement of design. Expose edges to be wrapped with machine glued only
edge banding tape of matching colours. All exposed surface of carcass to be
fiished with similar material as of shutters, (Sides). Thickness of tape shall not be
less than 0.8 mm thick of same colour and texture as of boxes material. This ply
shall be secured in the box with groove method and no screws are used to dix
the ply. All ply boxes to be fixed with rust proff screws only. No nails shall be
used to fix the boxes. Size of carcass D305x770H. length to be be determined as
per site.
211 NS-44 Supply and Fixing of Factory made wardrobe in HDHMR Boad of thickness 18 meter 1607.00 2800.00 - 44,99,600.00
mm for carcass and 25 mm thick for shutter and having 8 mm ply both side
laminated with 0.8 mm thick laminate. Inner side of carcass shall be provided
with 1mm thick of fabric or jute light color laminates on innner side and 1.5m
thickness High gloss, Anti scratch Acrylic laminates on all visible side with 2 mm
thick macthing colour edge binding tap machine glued. Dept of wardrobe shall
be 600 mm with drawers as per drawings and approved design. Hinges should of
soft closing type, sensor light should be provided. (Refer Technical
speficification for detail). Front area of shutter shall be measured for payment

212 Electrical Work

1.1) Wiring for light point/ fan point/exhaust fan point/call bell point with 1.5
sq. mm FRLS PVC insulated copper conductor single core cable in
surface/recessed medium class PVC conduit, with modular switch, modular
1.10
plate, suitable GI box and earthing the point with 1.5 sq. mm. FRLS PVC
insulated copper conductor single core cable etc as required.

a) 1.10.3 Group-C (Primary point ) Point 256.00 1467 375552 -

Digitally signed by
CHANDRESH KUMAR
Date: 2025.03.11 [Link] IST
 Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi
BILL OF QUANTITY

[Link] DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount
QTY DSR-2023 (Non-Schedule)

1.2) Wiring for group controlled (looping) light point /fan point / exhaust fan 0 -
point/call bell point (without independent switch etc) with 1.5 sqmm FRLS
1.55 PVC insulated copper conductor cable in surface/recessed PVC conduit and
earthing the point with 1.5sqmm FRLS PVC insulated copper conductor
single core cable [Link] required.
a) 1.55.3 Group-C (looping point ) Point 592.00 858 507936 -
1 Wiring for twin control light point with 1.5 [Link] FRLS PVC insulated 31240 -
copper conductor single core cable in surface / recessed medium class PVC
1.11 conduit, 2 way modular switch, modular plate, suitable GI box and earthing Point 20.00 1562
the point with 1.5 [Link]. FRLS PVC insulated copper conductor single core
cable etc as required.
1 Supplying and fixing suitable size GI box with modular plate and cover in 81090 -
front on surface or in recess, including providing and fixing 3 pin 5/6 amps
1.31 modular socket outlet and 5/6 amps modular switch, connection etc. as Each 170.00 477
required. (For light plugs to be used in non residential buildings).

2 Supplying and fixing suitable size GI box with modular plate and cover in 132436 -
front on surface or in recess, including providing and fixing 6 pin 5/6 &
1.32 Each 226.00 586
15/16 amps modular socket outlet and 15/16 amps modular switch,
connection etc. as required.
2 Supplying & fixing suitable size GI box wih modular plate and cover in front 40712 -
on surface or in recess including providing and fixing 25 A modular socket
1.57 Each 56.00 727
outlet and 25 A modular SP MCB, "C" curve including connections, painting
etc. as required.
2 Wiring for circuit/ submain wiring along with earth wire with the following 0 -
1.14 sizes of FRLS PVC insulated copper conductor, single core cable in surface/
recessed medium class PVC conduit as required
a) 1.14.1 Metre 2,960.00 233 689680 -
b) 1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire For Light Circuit Point Metre 1,280.00 275 352000 -
c) 1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire For Power Circuit Point Metre 850.00 334 283900 -
f) 4 X 10 sq. mm + 2 X 10 sq. mm earth wire For Submain Wire / Cable of DB 221100 -
1.14.10 Metre 220.00 1005

CABLE TRAYS AND ACESSERIES :

2 Supplying and installing following size of perforated pre-painted M.S. cable
trays with perforation not more than 17.5%, in convenient sections, joined
4.1
with connectors, suspended from the ceiling with M.S. suspenders including
bolts & nuts, painting suspenders etc as required.
a) 4.1.1 100 mm width X 50 mm depth X 1.6 mm thickness Metre 80.00 543.00 43440 -
b) 4.1.2 150 mm width X 50 mm depth X 1.6 mm thickness Metre 70.00 604.00 42280 -
2 Supplying and installing following size of perforated pre-painted M.S. cable 0 -
trays bends with perforation not more than 17.5%, joined with connectors,
4.2
suspended from the ceiling with M.S. suspenders including bolts & nuts,
painting suspenders etc as required.
a) 4.2.1 100 mm width X 50 mm depth X 1.6 mm thickness Each 80.00 868.00 69440 -
b) 4.2.2 150 mm width X 50 mm depth X 1.6 mm thickness Each 70.00 1,018.00 71260 -
2 Supplying and installing following size of perforated pre-painted M.S. cable 0 -
trays reducers with perforation not more than 17.5%, joined with
4.3
connectors, suspended from the ceiling with M.S. suspenders including
bolts & nuts, painting suspenders etc as required.
a) 4.3.1 100 mm width X 50 mm depth X 1.6 mm thickness Each 80.00 1,003.00 80240 -
b) 4.3.2 150 mm width X 50 mm depth X 1.6 mm thickness Each 70.00 1,186.00 83020 -
2 Supplying and installing following size of perforated pre-painted M.S. cable 0 -
trays Tee’s with perforation not more than 17.5%, joined with connectors,
4.4
suspended from the ceiling with M.S. suspenders including bolts & nuts,
painting suspenders etc as required.
a) 4.4.1 100 mm width X 50 mm depth X 1.6 mm thickness Each 80.00 1,139.00 91120 -
b) 4.4.2 150 mm width X 50 mm depth X 1.6 mm thickness Each 70.00 1,356.00 94920 -
3 Supplying and installing following size of perforated pre-painted M.S. cable 0 -
trays cross members with perforation not more than 17.5%, joined with
4.5
connectors, suspended from the ceiling with M.S. suspenders including
bolts & nuts, painting suspenders etc as required.
a) 4.5.1 100 mm width X 50 mm depth X 1.6 mm thickness Each 80.00 1,003.00 80240 -
b) 4.5.2 150 mm width X 50 mm depth X 1.6 mm thickness Each 70.00 1,186.00 83020 -
EARTHING INSTALLATION
5 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including 59776 -
accessories, and providing masonary enclosure with cover plate having
5.4 Nos. 8.00 7,472.00
locking arrangement and watering pipe 2.7 metre long etc. (but without
charcoal/ coke and salt ) as required.
5 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for 9296 -
5.14 RM 8.00 1,162.00
connections etc. as required.
5 Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for 16904 -
5.20 RM 8.00 2,113.00
connections etc. as required.
5 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for 1952 -
5.15 RM 8.00 244.00
connections etc. as required.
6 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop 336 -
5.18 earthing along with existing surface/ recessed conduit/submain wiring/ RM 8.00 42.00
cable as required.
DISTRIBUTION BOARDS
3 Supplying and fixing following way, horizontal type three pole and neutral,
sheet steel, MCB distribution board, 415 V, on surface/ recess, complete
2.4 with tinned copper bus bar, neutral bus bar, earth bar, din bar,
interconnections, powder painted including earthing etc. as required. (But
without MCB/RCCB/Isolator)
a) 2.4.3 8 way (4 + 24), Double door Each 20.00 4,974.00 99480 -
3 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, “C” curve, 0 -
miniature circuit breaker suitable for inductive load of following poles in the
2.10
existing MCB DB complete with onnections, testing and commissioning etc.
as required.
a) 2.10.1 Single pole (6/32 Amps) Nos. 480.00 256.00 122880 -

Digitally signed by
CHANDRESH KUMAR
Date: 2025.03.11 [Link] IST
 Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi
BILL OF QUANTITY

[Link] DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount
QTY DSR-2023 (Non-Schedule)

3 Supplying and fixing following rating, four pole, (three phase and neutral), 0 -
415 volts, residual current circuit breaker (RCCB), having a sensitivity
2.15
current 30 mA in the existing MCB DB complete with connections, testing
and commissioning etc. as required.
a) 2.15.2 40 A Each 60.00 3188 191280 -
3 Supplying and fixing following rating, four pole, 415 volts, isolator in the 0 -
2.13 existing MCB DB complete with connections, testing and commissioning etc.
as required.
a) 2.13.2 63 amps Nos. 20.00 1,227.00 24540 -
4 Supplying and fixing Single Pole Blanking Plate in the existing MCB DB 20680 -
2.11 Nos. 20.00 1,034.00
complete Etc. as required.
CONDUITING WIRING AND CABLING FOR TELEPHONE / TV NETWORK
SYSTEM

4 Supplying and fixing of following sizes of medium class PVC conduit along
1.21. with accessories in surface/recess including cutting the wall and making
good the same in case of recessed conduit as required.
a) 1.21.1 20mm RM 672.00 128 86016 -
b) 1.21.2 25mm RM 336.00 145 48720 -
c) 1.21.3 32mm RM 168.00 184 30912 -
4 Supply, fixing, connecting and testing of elephone/computer/TV modular 0 -
sockets modular plate anodised MS box and blanking late in
surface/recessed including connectionetc as required.
a) RJ-11 telephone socket two line with shutter 32424 -
1.24.6+1.2
Each 56.00 579
7.1+1.28.1
b) T.V. CO-axial cable socket outlets of one point 26656 -
1.24.7+1.2
Each 56.00 476
7.1+1.28.1
c) M.R RJ-45 face plate( computer line) with shutter DN-460 Each 56.00 500 0 28,000.00
4 Providing, fixing connecting and testing of solder less telephone Tag block 0 -
of following capacity ties as required in suitable size of m.s. hinged
lockable cover box duly painted etc. as required of Krone type.
a) M.R 10 pair Tele Tag Blk Each 2.00 7,500 0 15,000.00
4 Providing, fixing connecting and testing of solder less Television Junction 0 -
Box of following capacity ties as required in suitable size of m.s. hinged
lockable cover box duly painted etc. as required of Krone type.

a) M.R 2 pair T.V Junction Box. Each 112.00 2800 0 3,13,600.00

5 Supplying drawing, connecting and testing of 0.61mm dia annealed copper 0 -
conductor PVC insulated PVC sheathed telephone Wire/cables in Existing
PVC conduit or a racks as required.
a) 1.18.2 2 pair Telephone cable. (0.61sq mm) RM 336.00 38 12768 -
5 Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper 15792 -
conductor PE insulated, shielded with fine tinned copper braid and
1.19 RM 336.00 47
protected with PVC sheath in the existing surface/ recessed steel/ PVC
conduit as required.
5 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing 22344 -
1.53 RM 392.00 57
surface/ recessed steel/ PVC conduit as required.
5 Supplying and fixing metal box of following sizes (nominal size) on surface 0 -
1.22 or in reces with suitable size of phenolic laminated sheet cover in front
including painting etc as required.
a) 1.22.1 75 mm x 75 mm x 60 mm deep Each 168.00 178.00 29904 -

LIGHTS ITEMS
6 Supply, fitting, wiring, testing and commissioning of 40 W 2X2 RECESS 0 -
MR MOUNTED LED LIGHT all accessories as required. ( Wipro Item Model Each - 7200
Number DG24065)
6 Supply ,fixing , testing and commissioning of 10 W LED CEILING ROUND 0 74,800.00
MR Each 88.00 850
LIGHT all accessories as required.
6 Supply ,fixing , testing and commissioning of20 W LED CEILING TUBE LIGHT 0 1,58,400.00
MR Each 88.00 1800
all accessories as required.
6 Supply ,fixing , testing and commissioning of EXHAUST FAN. all accessories 0 84,000.00
MR Each 56.00 1500
as required.
7 Supply ,fixing , testing and commissioning of 15W CEILING LIGHT. all 0 8,20,000.00
MR Each 328.00 2500
accessories as required.
7 Supply ,fixing , testing and commissioning of 12W CFL CEILING LIGHT. all 0 2,20,800.00
MR Each 184.00 1200
accessories as required.
7 Supply ,fixing , testing and commissioning of MIRROR LIGHT. all accessories 0 34,000.00
MR Each 40.00 850
as required.
7 Supply ,fixing , testing and commissioning of CEILING FAN (1200MM ) all 0 1,80,000.00
MR Each 72.00 2500
accessories as required.
Cable, Mains and sub mains
0 7,00,524.00
Cable jointing kit for 11 KV (Earthed) grade cable for indoor termination cold
MR RM 40.00 17513.1
shrink type joint complete with jointing material and accessories suitable for 3
core XLPE armoured aluminium conductor cable of size 50 sqmm to 95qmm
Supplying and making end termination with brass compression gland and
aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE
aluminium conductor cable of 1.1 KV grade as required.
DSR 2022 3½ X 135 sq. mm (50mm) 0 85,820.00
Nos. 140.00 613
(9.1.25)
8 Supplying & laying of following 1100 volt grade XLPE insulated PVC sheathed
aluminium conductor armoured cables as per specification in existing trenches,
cable trays, ducts over bed of sand, clamped includes anchor fastners wall with
suitable clamps, saddles fixing bolts including connecting testing and
commissioning.
a.) M.R 3.5 core 70 sq. mm For External Lighting Panel RM 700.00 720.00 0 5,04,000.00
b.) M.R 4 core 25 sq. mm RM 587.53 450.00 0 2,64,389.85
8 Supplying and making end termination with brass compression gland and
aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE
aluminium conductor cable of 1.1 KV grade as required.
a.) DSR 2022 ( 18720 -
3½ X 70 sq. mm (38mm) Nos. 40.00 468.00
9.1.23)

Digitally signed by
CHANDRESH KUMAR
Date: 2025.03.11 [Link] IST
 Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi
BILL OF QUANTITY

[Link] DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount
QTY DSR-2023 (Non-Schedule)

b.) DSR 2022 9390 -

4 X 25 sq. mm (28mm) Nos. 30.00 313.00
(9.1.20)
CCTV SYSTEM
7 Supply, installation, testing and commissioning of DVR-20-CH, 400/480fps 0 2,70,000.00
display, 400f/480ps recording, H.264, Recording @704x480 (100/120ips)/
704x240 (200/240ips)/ 352x240 (400/480ips), 8Audio In/ 1 Out, 16 Alarm In,
4 Relay Out, Network Port available for Remote View S/W with
M.R Set 2.00 135000
transmission up to 120 IPS @ 352x288 PAL, along with 3 TB HDD, complete
all as specified with 230VAC power supply complete in all respects as per
specifications as per engineer in charge.

7 Supply, installation, testing and commissioning of High Resolution 32 inch 0 85,000.00

LCD colour TV monitor with on screen adjustment menu, durable metal
M.R Each 2.00 42500
cabinet etc. complete in all respects as per specifications as per engineer in
charge.
7 Supply, installation, testing and commissioning of IR & IP Based dome type 0 3,31,200.00
indoor coloured fixed camera with of 1/3" CCD,540 TVL, Sensitivity @ 30
IRE: Color 0.5Lx/Night Sense 0.18 Lx, AWB / BLC / AGC /Auto Black, 2.6 to 6
M.R Each 46.00 7200
mm vari-focal lens Auto Iris, 12VDC/24VAC for indoor application, complete
in all respects as per specifications as per engineer in charge.

7 Supply, drawing, installation, testing and commissioning of Video co-axial 0 27,600.00

M.R cable RG 11 in the existing surface / recessed steel/PVC conduit as required. RM 690.00 40

8 Supply, drawing, installation, testing and commissioning of armoured video 0 32,200.00

M.R co-axial cable RG 11 including trenching, excavation and backfilling as RM 460.00 70
required.
8 PVC, HDPE PIPES & PVC FLEXIBLE PIPES:: Supply & erection of PVC pipes & 0 -
HDPE pipes (fire retardant) for wiring purposes including bends, inspection
M.R
boxes etc., where necessary including other petty material as per PWD
General Specifications 2010:-
Heavy gauge PVC conduit pipe 20mm dia. (ISI marked 2mm thick) Flushed 0 14,720.00
RM 460.00 32
8 Supply and drawing of following sizes of PVC insulated copper conductor 0 -
M.R single core FRLS cable in the existing surface / recessed steel/PVC conduit as
required.
3 x 2.5 [Link]. RM 480.00 40 0 19,200.00
7.10. Supply, drawing, installation, testing and commissioning of PVC insulated 0 22,500.00
and PVC sheathed Instrumentation cable with electrolytic grade annealed
M.R bare flexible copper conductor shielded cable 2 core 16/0.2mm. cable in RM 300.00 75
the existing surface / recessed PVC/steel conduit as required.

7.11. Supply and laying of RG 59/RG 6 tinned copper co-axial cable with 0 10,500.00
M.R polythene insulation. RG 6 only in case of distance between camera and DVR RM 300.00 35

ELECTRICAL FLOOR PANEL

Supply, installation, testing and commissioning of following M.V. cubicle -
type totally enclosed, free standing type, dust, damp and vermin proof,
Distribution Board/Panel complete with busbars, M.V. danger notice plate,
MR interconnections with suitable capacity aluminium leads/ solid aluminium
strips/rods, connection of incoming and outgoing cables with thimbles,
powder coat painted and having following incoming and outgoing
switchgears complete as required.
a.) INCOMER: -
1 No. of 160 Amp 4P MCCB of 35 kA Breaking capacity with On Indicating -
Lamp with 2A SP MCB back-up.
Coloured (Red, Yellow, Blue) phase indicating lamp - 1 set -
(0 - 160 A) CT operated Ammeter with selector switch & 3 nos. CTs ratio -
160/5A ,15VA burden & accuracy class of 1.0 - 1 set
0-500 V Voltmeter with selector switch - 1 set -
b.) BUSBARS: -
200 Amp TPN Aluminium busbars -
c.) OUTGOING: -
8 Nos. 63 Amp DP MCB, with phase indicating lamps. -
2 Nos. 63 Amp DP MCB, SPARE. -
ELECTRICAL METER PANEL describe as above Set 2.00 3,36,300.00 6,72,600.00
ELECTRICAL FEEDER PILLAR PANEL
8.1) M.R ELECTRICAL FEEDER PILLAR PANEL
a) Incoming
1 No. 150 Amps FP MCCB with125 A changeover switch with following
accessories:
VAF digital electronic meter with inbuilt selector switch and 150/5 Amps suitable
VA, CL 1 CTs . -1 Set
Phase indicating light shall be protected by 2 Amps SP MCB's -3 Set
b) Bus Bars
250 Amps TPN Aluminium bars with heat coloured shrinkable insulation sleeve -
1 Set
c) Outgoing
63 Amps FP MCB - 10 No.
40 Amps FP MCB - 02 No.
32 Amps FP MCB - 02 No.
Spare
d) 63 Amps FP MCB - 02 No.
40 Amps FP MCB - 01 No.
Notes:-
i. All MCCB's shall be of 25 KA (Ics) breaking capacity.
ii All MCB's shall be of 10 KA breaking capacity.
ELECTRICAL FEEDER PILLAR PANEL described as above Set 2.00 2,35,000.00 0 4,70,000.00
MAIN LT PANEL & MAIN DISTRIBUTION PANEL

Digitally signed by
CHANDRESH KUMAR
Date: 2025.03.11 [Link] IST
 Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi
BILL OF QUANTITY

[Link] DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount
QTY DSR-2023 (Non-Schedule)

5 Design, fabrication, assembling, wiring, testing, supply, forwarding to site,

unloading, shifting to location, inspection, installation, testing and
commissioning of DG & Transformer Changeover Panel cum Main LT Panel, Main
distribution panels/ sub-distribution panels and capacitor panel, fabricated out
of 14 gauge CRCA sheet steel in cubicle formation, compartmentalized, from 3b
consutruction, free standing floor mounted, dust and vermin proof with
reinforcement of suitable size angle iron, channel, `T’ sections and/ or flats
wherever necessary. 16 gauge CRCA sheet steel shall be used for final
distribution panels. 3 mm thick cable gland plates shall be provided on top as
well as at the bottom of the panels. Panels shall be treated with all anticorrosive
process before powder coating as per specifications and final approved shade. 2
No. earthing terminals shall be provided for all distrtibution panels. Panels shall
be suitable for 415V, 3 phase, 4 wire, 50 HZ supply system. Lifting hooks shall
also be provided in case of large panels. Approval shall be taken for each panel
in the form of shop drawings before fabrication.

Galvanised hardwares with zinc passivation shall be used in fabrication of panels.

DG & TRANSFORMER CHANGEOVER CUM MIAN LT PANEL.

SECTION-I
a) DG Incoming Air Circuit Breaker from 62.5 kVA DG set - 1
250 amps 4 pole electrically operated manually draw out type Moulded circuit
breaker with microprocessor release unit , for short circuit, over current and
earth fault protection with adjustable setting as per specification and with
following accessories :
i. Digital energy meter with Maximum demand indicator (conzerve – EM 6400 or
equivalent) of accuracy class-I, with 3 Nos. 250/5 amps 15VA CTs.

ii. Phase sequence relay shall be protected by 2 Amps TP MCB - 1 Set

iii. Phase indicating light shall be protected by 2 Amps MCB’s. - 3 Sets
iv. Battery charger with voltmeter of range 0-50 volts and ammeter of range 0-50
amps for trickle and boost charging.
v. Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set
vi 24 V DC Shunt trip coil. - 1 Set
vii 240 V under voltage release. - 1 Set
viii. Breaker control switch - 1 Set
ix Excitor field DC voltmeter and ammeter.
x. Emergency stop push button.
xi. Selector switch for Auto / Manual / Test
xii. Selector switch for engine control OFF/ON.
xiii. Five push buttons – start, stop, reset, test and accept.
xiv. Three indicating lamps “load on set’, ‘Load on Mains’ and “ Set fail to start’.

xv. 12 Window alarm annunciators panel with hooter, push buttons, aux. Contactors
etc as required as per specification.
xvi. Suitable rating battery charger as per specifications
xvii. Temperature scanner (Messi Bus/Procon)
xviii. Auxiliary contacts required for necessary interlocking of breakers.
b) Incoming Air Circuit Breaker from 50 kVA Transformer-1
250 amps 4 pole electrically operated manually draw out type Moudule circuit
breaker with microprocessor release unit, for short circuit, over current and
earth fault protection with adjustable setting as per specification and with
following accessories :
Digital load manager (conzerve – EM 6400 with RS-485 or equivalent) of
accuracy class-I with 2 No. 250/5 amps 15VA CTs.
Phase indicating light shall be protected by 2 amps MCB’s- 3 Set
Three Phase Under voltage relay (27) - 1 Set
Three Phase Over voltage relay (59) - 1 Set
Breaker ON/ OFF/ TRIP indicating lights with control MCB’s- 1 Set
24 V DC Shunt trip coil. - 1 Set
240 V AC under voltage release. - 1 Set
Auto-manual / test selector / switch - 1 Set
Breaker control switch - 1 Set
Auxiliary contacts required for necessary interlocking of breakers.
Three phase Voltage sensor relay shall be protected by 2 amps TP MCB’s, 1 Set

Transient voltage surge supressor with suitable contactor shall be protected by 2

amps TP MCB’s. - 1 Set
Digital voltmeter with inbuilt selector switch- 1 set
c) Bus Bar :
500 A TPN electrolytic Al bus bar with heat shrinkable insulation sleeve
d) Outgoings
250 Amps 4 Pole MCCB - 6 No.
200 Amps 4 Pole MCCB - 7 No.
150 Amps 4 Pole MCCB - 5 No.
100 Amps 4 Pole MCCB - 6 No.
63 Amps 4 Pole MCCB - 5 No.
150 Amps 4 Pole MCCB - 3No. Spare
100 Amps 4 Pole MCCB - 2 No. Spare
e) Bus Coupler
500 amps 4 pole ACB, with ON/ OFF/ TRIP indicating lamps with microprocessor
release unit, etc complete as per specs.

Notes:-
All outgoing feeders shall have suitable range of followings:
i. All breakers shall be electrically interlocked as per schematic diagram.
ii. All ACB’s/ MCCB’s shall be suitable for 35 KA breaking capacity.
iii. PLC for load management and supervision.
v. Three phase indicating lamps shall be protected by 6 amps SP MCBs.
vi. 1 No. 1000/800/ 5, 15 VA dual ratio CT’s shall be provided for APFCR on
transformer's incomer.
vii. All outgoing feeders shall be provided with built-in short circuit & earth fault
relay module.
viii. All outgoing shall have dual Electronic energy meter (EM-6438 with RS-485 or
equivalent) with required number of CT's.
ix. Wiring and supply, installation of space heater, humidistat and control MCB’s
shall be provided for all vertical sections.
x. Suitable danger board shall be provided.
xi. All bus bar section/ backside panels shall have pad locking facility and hinged
type door.
xii. 9 W fitting with CFL lamp, switch shall be provided in each vertical section.
xiii. Incoming breakers shall have suitable provision for busduct connection..

Digitally signed by
CHANDRESH KUMAR
Date: 2025.03.11 [Link] IST
 Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi
BILL OF QUANTITY

[Link] DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount
QTY DSR-2023 (Non-Schedule)

xiv All Electronic Energy meter shall be pre wired for BMS connection upto central
point within the panel with sheilded cable.
M. R DG & Transformer Changeover Panel as described above. Set 2.00 9,43,000.00 0 18,86,000.00
5.2) M.R WATER SUPPLY PANEL
a) Incoming
1 No. 150 Amps TPN MCCB with125 A changeover switch with following
accessories:
VAF digital electronic meter with inbuilt selector switch and 150/5 Amps suitable
VA, CL 1 CTs . -1 Set
Phase indicating light shall be protected by 2 Amps SP MCB's -3 Set
b) Bus Bars
250 Amps TPN Aluminium bars with heat coloured shrinkable insulation sleeve -
1 Set
c) Outgoing
32 Amps TP MCB - 2 No.
25 Amps TP MCB - 6 No.
20 Amps TP MCB - 2 No.
20 Amps FP MCB - 1 No.
d) Spare
3 Amps 4P MCB - 3 No.
Notes:-
i. All MCCB's shall be of 25 KA (Ics) breaking capacity.
ii All MCB's shall be of 10 KA breaking capacity.
WATER SUPPLY PANEL described as above Set 2.00 3,26,818.00 0 6,53,636.00
5.3) M.R FEEDER PILLAR PANEL FOR EXTERNAL LIGHTING.
Supply, installation, testing and commissioning of cubicle type totally enclosed
free standing, dust free, damp and vermin proof and water proof outdoor (IP 55)
Feeder pillar fabricated out of 2mm thick CRCA sheet duly powder coated and
including supply & fixing the following items and interconnections, wiring with
suitable size wires/ cables and including all civil works like excavation, PCC, brick
work pedestal, plastering, refilling etc. and as per specifications as required.

INCOMER
1 No. 200 Amp four pole Moulded Case Circuit Breaker (Ics value 25 KA)
BUSBARS
300 Amp TPN busbars of high conductivity electrolytic quality aluminium alloy.

INSTRUMENTS & ACCESSORIES

1 No. 96x96 analogue type Voltmeter suitable range for 3 phase, 4 wire
operation with LED display and selector switch withcontrolled by 3 sets of 2Amp
MCB .
1 No.96x96 analogue typeAmmeter of suitable range ( 0 to 63Amp), for 3 phase
4 wire operation with LED display and selector switch
3 Nos of LED type phase indicating lamps (RYB) with controlled by 2Amp MCB .

1 No.6A, 2 pole Auto/OFF/Manual (2 way with OFF) selector switch.

2 Nos. of push button actuator
OUTGOING
Outgoing 1 (6 PM - 6 AM )
TPN DB 6 No. 10 amps SP MCB per phase as outgoing with 3 No. 40 amps DP
RCCB of 30 mA leakage current plus 1 No. 40 amps TP Contactor, push button
etc controlled through 0-24 hour timer, photo sensor and 1 No. 40 amps 4 pole
MCB as incomer).
Outgoing 2 ( 6 PM - 11.55 PM)
TPN DB 6 No. 10 amps SP MCB per phase as outgoing with 3 No. 40 amps DP
RCCB of 30 mA leakage current plus 1 No. 40 amps TP Contactor, push button
etc controlled through 0-24 hour timer, photo sensor and 1 No. 40 amps 4 pole
MCB as incomer).
Fidder pillar as discribed above Set 2.00 38,856.00 0 77,712.00
5.4) M.R Design, fabrication, assembling, wiring, supply, installation, testing and
commissioning of Automatic control panels with mixed die electric type
capacitors, fabricated out of 14 gauge CRCA sheet steel in cubicle
compartmentised, 3b modular construction, free standing, floor mounted, dust
and vermin proof with reinforcement of suitable size, angle iron, channel, `T’
sections and/ or flats wherever necessary. Cable gland plates shall be provided
on top the panels. Panels shall be treated with all anticorrosive process before
powder coating as per specifications and final approved shade. 2 No. earthing
terminals shall be provided for all distribution panels. Panels shall be suitable for
415V, 3 phase, 4 wire, 50 HZ supply system. Lifting hooks shall also be provided
in case of large panels. Approval shall be taken for each panel in the form of
shop drawings before fabrication. Galvanized hardwares with zinc passivation
shall be used in fabrication of panels.
50 KVAR CAPACITOR AUTOMATIC CONTROL PANEL
a) Incoming
150 amps TPN manually operated fully drawout type air circuit breaker as per
specification and with following accessories:
96 x 96 mm sq. 0-500 Volt digital voltmeter with selector switch
Phase indicating light shall be protected by 2 Amps SP MCB’s -3 Set
Power factor compensating relay (including power factor meter) in 10 steps for
automatic cut off or add on capacitor units to keep the power factor at 0.98 with
variation of loads. All associated auxiliary contactors/ relays/ timer/ auto manual
selector switches to be provided - 1 Set.

b) Bus Bars :
200 amps TPN Aluminium bus bars with coloured heat Shrinkable insulated
sleeves. - 1 set
c) Outgoings - I :
40 amps TPN MCB - 8 Set
Outgoing feeders consisting of following accessories.
80 amps or capacitor duty 525 volts 50 Hz contactors - 2 Sets
“ON” /”OFF” push buttons and indicating lamps - 2 Sets.
12.5 kVAr, 525 volts capacitor unit with detune filters as specified - 2 Sets.

d) Outgoings - II :
63 amps TPN MCB - 1 Set
Outgoing feeders consisting of following accessories.
80 amps or capacitor duty 525 volts 50Hz contactors - 1 Sets
“ON” /”OFF” push buttons and indicating lamps -1 Sets
25 kVAr, 525 volts capacitor unit with detune filters as specified - 1 Sets.

Note:
All MCCB’s shall be of 35 kA breaking capacity.
i. Fast response time of ‘ON’ capacitors 40-60 miliseconds.

Digitally signed by
CHANDRESH KUMAR
Date: 2025.03.11 [Link] IST
 Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi
BILL OF QUANTITY

[Link] DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount
QTY DSR-2023 (Non-Schedule)

ii. Necessary control and firing card with proper wiring and lugs of the required
rating to be provided.
iii. Heavy duty exhaust fans to be provided for cooling Thyristors
iv. LED indication for number of capacitor banks ‘ON’.
v. LED indication of Power Factor lagging or leading.
vi. The APFC system shall be provided with following :
Protections :
a. Over voltage.
b. Voltage imbalance.
c. Over temperature-system should be in standby mode
& automatically restart after above condition restored.
d. Earth leakage.
e. 7% value reactors with iron core.
Capacitor automatic control panel (500 kVA) as described above. Set 2.00 5,11,905.00 0 10,23,810.00
SUPPLY AND INSTALLATION OF DG SET WITH ACCESSORIES
4 Supply, installation, testing & commissioning of 62.5 KVA (Prime rated) diesel 0 11,56,420.00
generating set in acoustic enclosure, heat exchanger type alongwith day oil fuel
tank including first fill of diesel with fuel piping to and from DG set including
AMF Panel, vibration mounts, base frame, hardware Batteries, Engine control
M.R panel with accessories first fill of lube oil silencer with installation, flexible Sets 2.00 5,78,210.00
connection bellow / expansion joints etc.. complete and with all associated
equipment / work , cable / Bus bar terminal boxes and suitable mounting
arrangement for mounting of differntial CT,s protection as per specifications.

Exhaust Piping
4 Providing, fixing & installing MS exhaust pipe 6 mm thk and all fixing accessories
and hardwares. The exhaust pipes shall be Painted with high temperature paint
M.R & insulated with 75 mm thick mineral wool (density 150 kg/m3) insulation
wrapped in chicken mesh and clad with 26 gauge aluminium sheet including all
MS epoxy painted support structural as required.

a) 150 mm dia RM 60.00 5,512.00 0 3,30,720.00

Elevator
Supply, Installation, Testing and Commissioning of fully automatic 8 Nos.
Passanger (Minimum) Elevator, in lift shaft of dimensions 1500mm (W) x
2100mm (D), 544 Kg., with variable voltage variable frequency drive having
a speed of 1.5 metre/ sec and travel height of 19.40 m (approx.) with 6 Stops
and Microprocessor based control suitable for operation on 415 V, 50 Hz, 3
phase A.C. electric Supplying as required.
[Link] of machine Gearless, machine room less
[Link] 544 kg
3. Number of Passengers 8 Nos. (minimum)
[Link] 1.5 mps.
[Link] of landing 6 Landings(B+S+3+Terrrace Floor)
[Link] of openings 6 on the same side.
[Link] approx 19.40 meter
[Link] Supplying 415V/240V, 50HZ [Link] voltage
Fluctuation +10 to -20%
[Link] of Accelaration / 0.6-1.5 (adjustable at site) decelration
(m/[Link])
[Link] (m/[Link]) 0.7-1.5 (adjustable at site)
[Link] in car horizontal 20/18 MG maximum
vertical 20/18MG maximum
[Link] level in car 48dbA max.
13. Door noise level while closing and 52dbA max. opening at a distance
of 1mtr. from car door and 1.5 mtr. from floor level.

14. Type of Drive: Variable Voltage Frequency Drive V3F.

15. Location of Machine Room: Machine room less
16. Indicators car & landings: 7 Segment 25mm digital direction and
indicators in car and at all landings.
17. Special features/other features : Automatic Rescue Device with
dry maintenance free batteries
18. Call register type KDS-50 Micro pushbutton for Car and landing.
19. 3-Way Intercom
20. Manual Cranking operation
21. Integral shaft for gear and motor
22. Emergency Stop Button
23. CVT/Built Voltage Stablizer (Constant Voltage Transformer)
24. Pit ladder and ballustrade
25. Flooring : Provision for Granite flooring with 19mm recess.
26. Emergency cabin lighting and alarm.
27. FRD/Fire Man Drive (Fire Rescue Device)
28. Controls: Resolve Micro Processor based simplex full collective
control with or without attendant operation.
29. Door Safety : PANA 40-Full ray curtain for car door safety.
30. Load weighing device with indicator & bypass function.
31. Lift Announcement System (LAS)
32. Safety gears & over speed governer
33. Infra red door safety device
34. Civil works: All minor civil works such as scaffolding, making
holes, grouting, concreting etc.
35. Provision for connectivity of CCTV and other features complete in all respect

PASSENGER ELEVATORS-P1 as desctribed above Set 2 20,38,860.00 0 4077720

515
SUB HEAD -I: PUPM EQUIPMENT & ACCESSORIES IN TERRACE

Supplying, installation, testing and commissioning of electric driven terrace pump

18.4 suitable for automatic operation and consisting of following, complete in all 0 -
respects, as required: (Terrace Pump)
Horizontal type, multistage, centrifugal, split casing pump of cast iron body &
a) bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 0 -

Suitable HP squirell cage induction motor TEFC type suitable for operation on 415
volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, 0 -
b)
horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325.

[Link] common base plate, coupling, coupling guard, foundation bolts

c) 0 -
[Link] required.

Digitally signed by
CHANDRESH KUMAR
Date: 2025.03.11 [Link] IST
 Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi
BILL OF QUANTITY

[Link] DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount
QTY DSR-2023 (Non-Schedule)

Suitable cement concrete foundation duly plastered and with anti vibration pads
d) 0 -
18.4.1 900 lpm at 35 m Head Set 2 1,01,859.00 203718 -
0 -
Providing laying, testing and commissioning of class 'C' heavy duty MS pipe
confirming to IS 3589/1239 including fittings like elbows, tees, flanges, reducer,
jointing with nuts bolts, gasket and welding etc. and supports, as required and 0 -
18.7
painting with tow or more coats of synthetic enamel paiing of required shade
complet as directed by Engineer-iin-charge.

18.7.7 100mm dia Mtr. 100 2,555.00 255500 -

0 -
Supplying, fixing, testing and commissioning of butterfly valve PN 1.6, with
18.11 Bronze/Gunmetal seat duly ISI marked complete with Nuts, Bolts, washers, 0 -
gaskets, confirming to IS 13095, of following sizes as required.
18.11.5 100 mm dia Set 2 6,667.00 13334 -
0 -
Providing, installation, testing and commissioning of dual plate non-return valve
18.14 of following sizes confirming to IS 5312 complete with rubber gasket, GI bolts, 0 -
nuts, washers etc. as required.
18.14.5 100 mm dia Set 2 11,050.00 22100 -
0 -
Providing & fixing 100mm dia bourden type, Stainless steel dial type pressure
MR Gauge (0 - 16 Kg ) range, 3 / 8 " BSP bottom entry on Pump Delivery Line Each 2 859.00 0 1,718.00
complete with Ball valve
0 -
SUB HEAD -III: FIRE EXTINGUISHERS
0 -

Providing and fixing of carbon-di-oxide type fire extinguishers consisting of

welded M.S. cylindrical body, squeeze lever discharge valve fitted with pressure
indicating guage internal discharge tube 30 cms long high pressure discharge 0 -
24 MR
hose, discharge nozzle, suspension bracket conforming to ID:15683 finished
externally with red enamel paint and fixed to wall with brackets complete with
internal charge.
a) Capacity 4.5 Kg. Each 6 8,880.00 0 53,280.00
0 -
Providing and fixing of ABC Powder type fire extinguishers consisting of welded
M.S. cylinderical body, squeeze lever discharge valve fitted with pressure
indicating guage internal discharge tube 30 cms long high pressure discharge 0 -
25 MR
hose, discharge nozzle, suspension bracket conforming to ID:15683 finished
externally with red enamel paint and fixed to wall with brackets complete with
internal charge.
a) Capacity 4.0 Kg. Each 6 2,400.00 0 14,400.00
0 -
0 -
SUB HEAD-V : SPRINKLER SYSTEM & PIPING
0 -

Providing laying, testing and commissioning of class 'C' heavy duty MS pipe
confirming to IS 3589/1239 including fittings like elbows, tees, flanges, reducer,
1.0) jointing with nuts bolts, gasket and welding etc. and supports, as required and 0 -
1
painting with tow or more coats of synthetic enamel paiing of required shade
complet as directed by Engineer-iin-charge.

1.1 25 mm dia Metre 180 471 84780 -

1.2 32 mm dia Metre 80 527 42160 -
1.3 40 mm dia Metre 110 651 71610 -
1.4 50 mm dia Metre 30 787 23610 -
1.5 65 mm dia Metre 24 1,004 24096 -
1.6 80 mm dia Metre 20 1,122 22440 -
1.7 100 mm dia Metre 10 1,499 14990 -
1.8 150 mm dia Metre 10 2,064 20640 -
0 -
Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type
0 -
sprinklers of rating 68 degree centigrade with required accessories :
1.1) 1.9 Pendent Sprinkler Each 72 484 34848 -
0 -

Digitally signed by
CHANDRESH KUMAR
Date: 2025.03.11 [Link] IST