Specifications for Vector Signal Generator R&S SMIQ

Valid from 7/2002

Specifications are guaranteed under the following conditions: 30 minutes warmup time at ambient temperature, specified environmental conditions met, calibration cycle adhered to, and total calibration performed. Data designed overrange are not guaranteed. Data without tolerances: typical values. In compliance with the 3GPP standard, chip rates are specified in Mcps (million chips per second), whereas bit rates, symbol rates and sample rates are specified in kbps (thousand bits per second) or ksps (thousand symbols/samples per second). Mcps, kbps and ksps are not SI units.

RF features
Frequency
Range R&S R&S R&S R&S SMIQ02B SMIQ03B SMIQ04B SMIQ06B 300 300 300 300 kHz kHz kHz kHz to to to to 2.2 3.3 4.4 6.4 GHz GHz GHz GHz

Resolution (CW, analog modulation, attenuator mode AUTO)

7

0.1 Hz

Setting time to within <1x10 for f>450 MHz and <240 Hz for f<450 MHz after IEC/IEEE-bus delimiter with ALC MODE set to ON or ALC OFF MODE set to TABLE Normal operation f 3.3 GHz f > 3.3 GHz After trigger pulse in list mode f 3.3 GHz f > 3.3 GHz Fast restore mode f 3.3 GHz f > 3.3 GHz Phase offset <3 ms <3.3 ms <500 s <700 s <800 s <1 ms adjustable in steps of 0.1

Reference frequency
Standard Aging (after 30 days of operation) Temperature effect (0C to 50C) Warm-up time Output for internal reference Frequency Level Source impedance Input for external reference Frequency Permissible frequency drift Input level Input impedance Electronic tuning (EXT. TUNE) Input voltage range Input impedance 1x107/V 0 V to 10 V 10 k 10 MHz 8 dBm 50 1 MHz to 16 MHz in 1 MHz steps 3x106 0.1 V to 2 V rms 200 values to standard, but with Adjustment State On 1x106/year 2x106 Option R&S SM-B1 <1x109/day <5x108 15 min

Level
Range R&S SMIQ02B/03B R&S SMIQ04B/06B Overranging without guarantee of specs Resolution (CW, FM, M, attenuator mode AUTO) 2
Vector Signal Generator R&S SMIQ Specifications

144 dBm to +13 dBm (PEP) 144 dBm to +10 dBm (PEP) up to 16 dBm 0.1 dB or 0.01 dB

1) 1)

Total level uncertainty >127 dBm f 2.5 GHz f >2.5 GHz to 4 GHz f >4 GHz to 6.4 GHz Output impedance VSWR max. level 3 dBm

2 ) 12 )

, CW <0.5 dB <0.9 dB <1.2 dB 50 f 2.2 GHz <1.8 <1.5 2.2 GHz < f 6.4 GHz <2.0 <1.8

Setting time to within 0.1 dB from settled level after IEC/IEEE bus delimiter in CW, FM, M Non-interrupting level setting FIXED mode ELECTRONIC mode Overload protection Max. permissible RF power Max. permissible DC voltage

<25 ms with mechanical attenuator <2.5 ms without mechanical attenuator setting range >20 dB setting range >80 dB protects the unit from externally applied RF power (from 50 source) and DC voltage 50 W (R&S SMIQ02B/R&S SMIQ03B) 1 W (R&S SMIQ04B/R&S SMIQ06B) 35 V (R&S SMIQ02B/R&S SMIQ03B) 0 V (R&S SMIQ04B/R&S SMIQ06B)

Spectral purity
Spurious Harmonics

2)

at levels 10 dBm (R&S SMIQ02B/03B) <30 dBc at levels 7 dBm (R&S SMIQ04B/06B) CW, carrier offset >10 kHz 0.3 MHz to 450 MHz >450 MHz to 1500 MHz >1500 MHz to 3000 MHz >3000 MHz to 3300 MHz >3300 MHz Vector modulation, carrier offset 10 kHz to < 300 MHz 0.3 MHz to 3300 MHz carrier offset 300 MHz 0.3 MHz to 3300 MHz carrier offset 10 kHz to < 900 MHz >3300 MHz to 6000 MHz >6000 MHz carrier offset 900 MHz >3300 MHz, 5 dBm <74 dBc <80 dBc <74 dBc <60 dBc as with vector modulation

Nonharmonics

<70 dBc <60 dBc <64 dBc <58 dBc <50 dBc

Broadband noise, CW, carrier offset >5 MHz, measurement bandwidth 1 Hz f >20 MHz to 450 MHz f >450 MHz to 3040 MHz f >3040 MHz to 3300 MHz f >3300 MHz to 6400 MHz Broadband noise, vector modulation, f >20 MHz, carrier offset >5 MHz to 3300 MHz f >20 MHz, carrier offset >3300 MHz to 6400 MHz SSB phase noise, carrier offset 20 kHz, measurement bandwidth 1 Hz f = 20 MHz to 450 MHz f = 1 GHz f = 2 GHz f = 3 GHz f = 6 GHz

<136 <138 <136 <132

dBc dBc dBc dBc

(142 (144 (142 (138

dBc dBc dBc dBc

typ.) typ.) typ.) typ.)

<136 dBc (140 dBc typ.) <133 dBc (137 dBc typ.) CW <116 <126 <120 <116 <110 Vector/dig. mod. <119 dBc <123 dBc <120 dBc <116 dBc <110 dBc
Vector Signal Generator R&S SMIQ Specifications

dBc dBc dBc dBc dBc

Residual FM, rms (f = 1 GHz) 0.3 kHz to 3 kHz (ITU-T) 0.02 kHz to 23 kHz Residual AM, rms (0.02 kHz to 23 kHz)

<1 Hz <4 Hz <0.02%

Sweep
RF sweep, AF sweep Modes Sweep range Step width (lin) Step width (log) Level sweep Modes Sweep range Step width (log) Step time Resolution Markers MARKER output signal X output BLANK output signal digital sweep in discrete steps automatic, single shot, manual or external trigger, linear or logarithmic user-selectable user-selectable 0.01% to 100% not available with vector or digital modulation automatic, single shot, manual or external trigger, logarithmic 0.1 dB to 20 dB 0.1 dB to 20 dB 3 ms to 5 s 0.1 ms 3, user-selectable TTL level (HCT), selectable polarity 0 V to 10 V TTL level (HCT), selectable polarity

Internal modulation generator

Frequency range Resolution Frequency error Frequency response up to 100 kHz Frequency response up to 1 MHz Distortion up to 100 kHz (RL >200 , peak level 1 V) Open-circuit voltage at LF socket Resolution Setting error at 1 kHz Output impedance Frequency setting time (after receiving last IEC/IEEE-bus character) 0.1 Hz to 1 MHz 0.1 Hz <(1x104 of setting + 0.012 Hz) <0.4 dB <2 dB <0.2% 1 mV to 4 V peak 1 mV 1% + 1 mV approx. 10 <3 ms

Vector Signal Generator R&S SMIQ Specifications

Analog modulation
Vector modulation
Level accuracy with vector modulation, additional error with <0.3 dB ALC OFF, relative to CW Mode I and Q modulation inputs Input impedance VSWR (DC to 30 MHz) If R&S SMIQ is fitted with two fading simulators (R&S SMIQB14 and R&S SMIQB15) and a noise generator and distortion simulator (R&S SMIQB17), the VSWR of the I and Q inputs for vector modulation (DC to 30 MHz) degrades to Input voltage for full-scale input Static error vector 3 ) level 8 dBm PEP (R&S SMIQ02B/03B) level 5 dBm PEP (R&S SMIQ04B/06B) up to 3.3 GHz rms value peak value >3.3 GHz rms value peak value Modulation frequency response up to 5 MHz up to 30 MHz Carrier leakage at 0 V input voltage, referred to full-scale input 3 ) I/Q impairments Carrier leakage Setting range Resolution IQ Setting range Resolution Quadrature offset Setting range Resolution external DC 50 <1.2

<1.25 I 2 + Q 2 = 0.5 V (1 V EMF with 50 source)

<0.5% <1% <1% <2% <0.4 dB <3 dB <45 dBc

0% to 50% 0.5% 12% to +12% 0.1% 10 to +10 0.1

Envelope control RF level can be controlled with an analog voltage of 0 V to 1 V 1 V: set level via the POWER RAMP input 0 V: maximum level attenuation 10 k Input impedance 0 dB to 30 dB (35 dB typ.) Linear range <0.5 dB Attenuation error at 20 dB >80 dB On/off ratio 1 s typ. Delay time <1 s Rise/fall time (10% to 90%)

Vector Signal Generator R&S SMIQ Specifications

Amplitude modulation
Modes Modulation depth Resolution

2)

internal, external AC/DC 0% to 100% 0.1% <4% of reading +1% <1% <2% DC to 50 kHz DC to 3 kHz <3 dB <3 dB <0.1 rad >100 k 1 V peak for inaccuracy >3%

Setting error at 1 kHz (m <80%) AM distortion at 1 kHz m = 30% m = 80% Modulation frequency range, RF 5 MHz for RF <5 MHz Modulation frequency response 20 Hz to 20 kHz for RF <5 MHz, 20 Hz to 3 kHz Incidental M at 30% AM, AF = 1 kHz, peak value Modulation input EXT1 Input impedance Input voltage for selected modulation depth High/low indication (10 Hz to 50 kHz)

Broadband amplitude modulation

Mode Modulation frequency response up to 10 MHz up to 30 MHz Modulation input (broadband AM) Input impedance Input voltage for 100% AM external DC <1 dB <3 dB 50 0.25 V peak

Pulse modulation
Modes On/off ratio Rise/fall time (10%/90%) Pulse repetition frequency Pulse delay Modulation input PULSE Input signal Input impedance external >80 dB 30 ns typ. 0 kHz to 1 MHz 200 ns typ. TTL level (HCT) >10 k

Frequency modulation with option R&S SM-B5

Modes Max. deviation without I/Q modulation 0.3 MHz to 450 MHz >450 MHz to 750 MHz >750 MHz to 1500 MHz >1500 MHz to 3300 MHz >3300 MHz to 6400 MHz 6
Vector Signal Generator R&S SMIQ Specifications

internal, external AC/DC, two-tone with two modulation channels FM1 and FM2 2 MHz 0.5 MHz 1 MHz 2 MHz 4 MHz

Max. deviation with I/Q modulation 0.3 MHz to 750 MHz >750 MHz to 1200 MHz >1200 MHz to 3300 MHz >3300 MHz to 6400 MHz Resolution Setting error at AF = 1 kHz FM distortion at AF = 1 kHz and half maximum deviation Modulation frequency range with maximum deviation at <25% of maximum deviation Modulation frequency response 10 Hz to 100 kHz 10 Hz to 2 MHz Incidental AM at 40 kHz deviation, AF = 1 kHz, carrier frequency >5 MHz Carrier frequency offset with FM EXT1, EXT2 modulation inputs Input impedance Input voltage for selected modulation depth High/low indication (10 Hz to 100 kHz)

2 1 2 4

MHz MHz MHz MHz

<1%, min. 10 Hz <(3% of setting + 20 Hz) <0.5% DC to 500 kHz DC to 2 MHz <0.5 dB <3 dB <0.1% <0.01% of maximum deviation +1% of selected deviation >100 k 1 V peak for inaccuracy >3%

Phase modulation with option R&S SM-B513 )

Modes Max. deviation without I/Q modulation 0.3 MHz to 450 MHz >450 MHz to 750 MHz >750 MHz to 1500 MHz >1500 MHz to 3300 MHz >3300 MHz to 6400 MHz Max. deviation with I/Q modulation 0.3 MHz to 750 MHz >750 MHz to 1200 MHz >1200 MHz to 3300 MHz >3300 MHz to 6400 MHz Resolution Setting error at AF = 1 kHz Distortion at AF = 1 kHz and half maximum deviation Modulation frequency range Modulation frequency response 10 Hz to 100 kHz EXT1, EXT2 modulation inputs Input impedance Input voltage for selected modulation depth High/low indication (10 Hz to 100 kHz) internal, external AC/DC, two-tone with two modulation channels PM1 and PM2 20 rad 5 rad 10 rad 20 rad 40 rad 20 rad 10 rad 20 rad 40 rad <1%, min. 0.001 rad <3% of reading + 0.01 rad <1% DC to 100 kHz <0.8 dB >100 k 1 V peak for inaccuracy >3%

Vector Signal Generator R&S SMIQ Specifications

Digital modulation
Digital modulation with optional Modulation Coder R&S SMIQB20
Modes Predefined modulation settings internal, external serial, external parallel APCO C4FM, APCO CQPSK, CDPD, CT2, DECT, GSM, IRIDIUM, NADC, PDC, PHS, TETRA, TFTS, PWT, ICO BPSK, ICO GMSK, ICO QPSK, GSM EDGE, CDMA IS-95, WCDMA, QPSK selectable lengths: 291, 2151, 2161, 2201, 2211 and 2231 12 MHz

Internal PRBS I/Q bandwidth

Modulation specifications apply at levels 8 dBm (PEP) with R&S SMIQ02B/03B and at levels 5 dBm (PEP) with R&S SMIQ04B/06B Total level uncertainty at levels >127 dBm with digital modulation, crest factor <20 dB 2) 3) f 2,5 GHz f >2,5 GHz to 4 GHz f >4 GHz Clock generation Clock mode Resolution Error Inputs

<0.7 dB <1.2 dB <1.5 dB

For best short time repeatability use ALL OFF mode table internal or external 0.001 Hz <242, related to reference frequency DATA, BIT CLOCK, SYMBOL CLOCK, PAR DATA

Serial data are taken from BNC connectors, parallel data (symbols) from rear PAR DATA connector. Parallel symbols may contain 1 to 8 bits and read in using an internal or external clock signal Trigger threshold Input impedance Max. data rate, serial Max. symbol rate, parallel Outputs I and Q baseband signals, output voltage, EMF, peak value Power ramp Output voltage Output impedance Level attenuation via LEV ATT input Range Additional level error caused by attenuation Envelope control Modes Analog Digital 2.5 V to +2.5 V, selectable, resolution 0.01 V 1 k to ground, 50 to ground 30 MHz, 50 MHz typ. 18 MHz DATA, BIT CLOCK, SYMBOL CLOCK, PAR DATA, (all TTL levels) I 2 + Q 2 = 1V 0 V to 1 V 10

3)

0 dB to 70 dB <1 dB (up to 35 dB), <1.5 dB (up to 70 dB)

External via POWER RAMP input (for data see vector modulation above). With an internal power ramp, the connector serves as an output. Internal or external via BURST GATE input/output (PAR DATA connector). The BURST GATE input triggers a power ramp (TTL levels). The low/high transition starts the ramp function from blanking level to maximum level, the high/low transition from maximum level to blanking level. With an internal power ramp, the connector serves as an output. 1 kHz to 2.5 MHz 0.25 symbols to 32 symbols 1/4 symbol 1 s ASK, FSK, GMSK, PSK, QAM

Operating range Rise/fall time Setting range Resolution Minimum time Modulation modes

Vector Signal Generator R&S SMIQ Specifications

Baseband filter Each filter can be used with any type of modulation. Exception: GMSK/GFSK only with Gaussian baseband filter

cos ( = 0.1 to 0.99), cos ( = 0.1 to 0.99), resolution 0.01 Gauss, B x T = 0.15 to 2.5, resolution 0.01 GaussLin, B x T = 0.3 Bessel, B x T = 1.25 and 2.5/ IS-95 with or without equalizer / special filter for WCDMA, APCO C4FM / special filter for TETRA / split phase, B x T = 0.15 to 2.5 / rectangular low EVM: for minimum error vector low ACP: for minimum adjacent-channel power 100 Hz to 18 MHz 0% to 100%
11 )

Filter modes ASK Symbol rate Modulation depth FSK Modulation modes Symbol rate Shift Resolution

, max. 5 MHz

2FSK, 4FSK, 4FSK APCO, GFSK 100 Hz to 7.5 MHz

11 )

(0.1 to 100) x fsymb , max. 5 MHz <0.5%

Deviation error, rms value for shift 200 Hz to 650 kHz, symbol rate <1.3 Msymbol/s, filter cos or cos with = 0.25 to 0.7 or Gauss with B x T = 0.2 to 0.7 <1.3% GMSK Bit rate Modulation phase error with PRBS data, up to 1 Mbit/s, rms value Peak value PSK Modulation modes Symbol rate Error vector magnitude, rms for filter cos, cos, IS-95, WCDMA up to 200 ksymbol/s, 0.25 up to 1.5 Msymbol/s, 0.25 up to 3 Msymbol/s, 0.25 >3 Msymbol/s, 0.25 TETRA ACP f = (380 to 470) MHz, (915 to 988) MHz, level 8 dBm PEP, low distortion output mode Offset 25 kHz Offset 50 kHz QAM Modulation modes Symbol rate Error vector magnitude, rms with 16QAM for filter cos, cos, IS-95, WCDMA up to 1 Msymbol/s, 0.25 up to 3 Msymbol/s, 0.25 >3 Msymbol/s, 0.25 100 Hz to 7.5 MHz <1 <3 BPSK, QPSK, OQPSK, QPSK (IS-95), OQPSK (IS-95), QPSK (ICO), QPSK (INMARSAT), /4DQPSK, /4QPSK, 8PSK, 8PSK EDGE 100 Hz to 18 MHz
11 ) 11 )

<1.2% <2% <3% typ. <3%

71 dB, 74 dB typ. 76 dB, 80 dB typ. 16QAM, 32QAM, 64QAM, 256QAM 100 Hz to 18 MHz <2% <3% <3% typ.
11 )

Vector Signal Generator R&S SMIQ Specifications

User mapping Modulation modes Modulation symbols Coding Range of symbol rate User baseband filter Impulse length Oversampling Modulation coding

via IEEE bus with software User Mod PSK, QAM, FSK 1 to 8 bit per symbol differential, phase offset (PSK) like PSK, QAM and FSK via IEEE bus with software User Mod 8 or 16 symbols long 3 to 32 differential coding, differential and Gray, GSM, NADC, TETRA, TFTS, PDC, PHS, differential phase coding, APCO25, PWT, INMARSAT, VDL

Modulation with coding

The table below shows the possible combinations of modulation with coding (X = combination possible). Coding Differential Differential Differential off phase + Gray ASK BPSK QPSK QPSK (IS-95) INMARSAT QPSK ICO OQPSK OQPSK (IS-95) /4 QPSK /4 DQPSK 8PSK 8PSK_EDGE 2FSK 4FSK, 4FSK APCO GFSK GMSK 16QAM 32QAM 64QAM 256QAM X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X GSM NADC, PDC,PHS, TETRA,APCO25, PWT TFTS/ TETRA INMARSAT VDL

Data generator (option R&S SMIQB11)

Programmable data memory for modulation data, envelope-control and trigger signals. The data generator can be operated only in conjunction with the optional modulation coder (R&S SMIQB20). Memory capacity Max. symbol rate Modes 15 Mbit 8.5 MHz automatically repeating, single shot, manually or externally triggered

10

Vector Signal Generator R&S SMIQ Specifications

Inputs Trigger input TRIGIN Trigger frequency Selectable trigger delay Selectable trigger suppression Switching threshold Input impedance Required pulse width Outputs DATA modulation data BURST GATE, LEV ATT CW TRIGOUT 1, TRIGOUT 2 TRIGOUT 3 HOP

for starting the data sequences in the data memory <10 kHz 0 to 2161 symbols 0 to 2261 symbols after trigger 2.5 V to 2.5 V, selectable, resolution 0.1 V 1 k to ground, 50 to ground >50 ns see data under Digital Modulation control signals for envelope control and level attenuation control signal for switching off digital modulation user-programmable trigger signals trigger signal on event control signal for frequency hopping in LIST MODE

Memory extension (option R&S SMIQB12)

The data generator memory can be extended to max. 79 Mbit by fitting up to two options R&S SMIQB12. Memory capacity 32 Mbit

Digital standards with options R&S SMIQB20 and R&S SMIQB11

Modulation and ACP specifications apply at the respective standard frequency ranges and at levels 8 dBm PEP with R&S SMIQ02B/03B 5 dBm PEP with R&S SMIQ04B/06B Data sources with TDMA with CDMA Digital standard GSM / EDGE Frequency Standard Range Modulation Symbol rate Standard Range Baseband filter (GMSK) Standard Range Baseband filter (8PSK EDGE) Frame structure

internal, external via RS232 interface (SERDATA) internal to GSM standard 880 MHz to 960 MHz/1710 MHz to 2000 MHz same as R&S SMIQ GMSK or 8PSK EDGE (8PSK with 3/8 rotation) 270 833 Hz 100 Hz to 300 kHz Gauss, BxT = 0.3 Gauss, BxT = 0.2 to 0.7 Gauss Linear 1 to 8 slots user-definable any burst types can be combined, incl. GSM and EDGE mixed NORMAL, DUMMY, ALL DATA, NORMAL EDGE >80 dB corresponding to 3 symbols, <18 s 0 dB to 70 dB PRBS, 291, 2111, 2151, 2161, 2201, 2211, 2231, programmable data memory asynchronous via RS232 interface (SERDATA)

Burst types Burst on/off ratio Burst rise/fall time Slot attenuation, selectable Internal modulation data External serial modulation data

Vector Signal Generator R&S SMIQ Specifications

11

GMSK Phase error, rms value Phase error, peak value 8PSK EDGE Error vector magnitude, rms Offset 200 kHz Offset 400 kHz Offset 600 kHz Digital standard DECT Frequency Standard Range Modulation Deviation with GFSK Standard Range Symbol rate Standard Range with GFSK Range with /4 DQPSK Baseband filter Standard Range Frame structure Slot types Burst on/off ratio Burst rise/fall time Slot attenuation, selectable Internal modulation data Deviation error, rms Special functions Timing adjustment simulation Range Jitter simulation Range Slot timing shift Range Selectable preamble Response during ramp-up Digital standard NADC Frequency Standard Range Modulation Symbol rate Standard Range

<1, 0.3 typ. <3, 1 typ. <1.2%, 0.6% typ. 34 dB 70 dB 78 dB to ETS300175-2 and ETS300176-1 1880 MHz to 1900 MHz same as R&S SMIQ GFSK (standard), /4 DQPSK 288 kHz (0.1 to 1) x fsymb 1152000 Hz 100 Hz to 1200 kHz 100 Hz to 1200 kHz Gauss, B x T = 0.5 Gauss, B x T = 0.2 to 0.7 cos ( = 0.2 to 0.7), cos ( = 0.2 to 0.7) 1 to 12 slots of 24 slots user-definable FULL (basic), DOUBLE (high capacity), ALL DATA >80 dB corresponding to 2 symbols, <10 s 0 dB to 70 dB PRBS, 291, 2151, 2161, 2201, 2211, 2231, programmable data memory <1.3% lengthening (+) or shortening () of every 35th frame 4 bit to +4 bit (resolution 1 bit) time lead for even-numbered frames 0 bit to +4 bit (resolution 1 bit) time shifting of a single slot 9 bit to +9 bit (resolution 1 bit) normal or prolonged modulated or CW to IS-54 and IS-136 824 MHz to 894 MHz/1850 MHz to 2000 MHz same as R&S SMIQ /4 DQPSK 24.300 kHz 100 Hz to 200 kHz

Power density spectrum, typ. values (standard, resolution bandwidth 30 kHz, without power ramping)

12

Vector Signal Generator R&S SMIQ Specifications

Baseband filter Standard Range Frame structure Burst types Burst on/off ratio Burst rise/fall time Slot attenuation, selectable Internal modulation data External serial modulation data Error vector magnitude, rms Adjacent-channel power, typ. values, without power ramping Offset 30 kHz Offset 60 kHz Offset 90 kHz Digital standard PDC Frequency Standard Range Modulation Symbol rate Standard Range Baseband filter Standard Range Frame structure Burst types Burst on/off ratio Burst rise/fall time Slot attenuation, selectable Internal modulation data External serial modulation data Error vector magnitude, rms Adjacent-channel power, typ. values, without power ramping Offset 50 kHz Offset 100 kHz Digital standard PHS Frequency Standard Range Modulation Symbol rate Standard Range Baseband filter Standard Range

cos (=0.35), cos (=0.35) cos (=0.2 to 0.7), cos (=0.2 to 0.7) 1 to 6 slots user-definable for uplink and downlink Up/Down TCH, ALL DATA, Up SHORT >80 dB corresponding to 3 symbols, <123.4 s 0 dB to 70 dB PRBS, 291, 2111, 2151, 2161, 2201, 2211, 2231, programmable data memory asynchronous via RS232 interface (SERDATA) <1.2%, 0.4% typ.

35 dBc 75 dBc 78 dBc to RCR STD-27 810 MHz to 826 MHz/940 MHz to 956MHz /1429 MHz to 1453 MHz/1477 MHz to 1501 MHz same as R&S SMIQ /4 DQPSK 21 kHz 100 Hz to 200 kHz cos (=0.5), cos (=0.5) cos (=0.2 to 0.7), cos (=0.2 to 0.7) 1 to 6 slots user-definable for uplink and downlink TCH, SYNC, VOX, ALL DATA >80 dB corresponding to 2 symbols, <95.2 s 0 dB to 70 dB PRBS, 291, 2111, 2151, 2161, 2201, 2211, 2231, programmable data memory asynchronous via RS232 interface (SERDATA) <1.2%, 0.4% typ.

74 dBc 78 dBc to RCR STD-28 1895.0 MHz to 1918.1 MHz same as R&S SMIQ /4 DQPSK 192 kHz 100 Hz to 200 kHz cos (=0.5), cos (=0.5) cos ( = 0.2 to 0.7), cos ( = 0.2 to 0.7)

Vector Signal Generator R&S SMIQ Specifications

13

Frame structure Burst types Burst on/off ratio Burst rise/fall time Slot attenuation, selectable Internal modulation data External serial modulation data Error vector magnitude, rms Adjacent-channel power, typ. values, without power ramping) Offset 600 kHz Offset 900 kHz

1 to 8 slots user-definable TCH (32 kbit and 16 kbit channel), SYNC, VOX, ALL DATA >80 dB corresponding to 2 symbols, <13 s 0 dB to 70 dB PRBS, 291, 2111, 2151, 2161, 2201, 2211, 2231, programmable data memory asynchronous via RS232 interface (SERDATA) <1.2%, 0.4% typ.

74 dBc 76 dBc

Digital standard IS-95 CDMA with option R&S SMIQB42

Modulation and ACP specifications apply at the respective standard frequency ranges and at levels 8 dBm PEP with R&S SMIQ02B/03B 5 dBm PEP with R&S SMIQ04B/06B To TIA standard IS-95A and J-STD-008 Frequency Standard Range Modulation Chip rate Standard Range Reverse link coded Sequence length Forward link Reverse link

824 MHz to 894 MHz, 1850 MHz to 2000 MHz same as R&S SMIQ QPSK, OQPSK 1.2288 MHz 0.1 Mcps to 7 Mcps 0.1 Mcps to 1.3 Mcps 1 superframe (80 ms) 1 superframe (80 ms) if user-definable data lists are used: calculation in real time, ie unlimited sequence length calculation in real time, ie unlimited sequence length IS-95 with or without equalizer cos (=0.2 to 0.7), cos (=0.2 to 0.7) 1 to 18 0 to 63 0.0 dB to 30 dB, 4 user-definable levels 1 to 64 0.0 dB to 30 dB, 2 user-definable levels full-rate mode, half-rate mode with random power gating incl. frame quality indicator, convolutional encoder, block interleaver traffic channel, 9600/4800/2400/1200 bps traffic channel, 14400/7200/3600/1800 bps access channel, 4800 bps

Reverse link coded Baseband filter Standard Other filters Forward link, mode 18 Number of code channels Walsh code selectable Code channel power Forward link, mode 64 Number of code channels Code channel power Reverse link Reverse link coded

14

Vector Signal Generator R&S SMIQ Specifications

Internal modulation data Forward link, 19200 bit/s Reverse link, 28800 bit/s Reverse link coded Synchronization signals (chip rate 1.2288 Mcps) Modulation accuracy Adjacent-channel power ratio at 30 kHz bandwidth Reverse link Offset 885 kHz Offset 1.25 MHz Offset 1.98 MHz With option R&S SMIQB47, IQ filter 850 kHz Offset 885 kHz Offset 1.25 MHz Offset 1.98 MHz 9 channels forward link Offset 885 kHz Offset 1.25 MHz Offset 1.98 MHz With option R&S SMIQB47, IQ filter 850 kHz Offset 885 kHz Offset 1.25 MHz Offset 1.98 MHz

PRBS, 0 sequence, 1 sequence, 01 alternating, different for each code channel PRBS, 0 sequence, 1 sequence, 01 alternating, programmable data memory PRBS, 291, 2151, 2161, 2201, 2211, 2231, programmable data memory chip clock, input and output, 2 outputs for 80 ms, 80/3 ms, 20 ms, 2 s clock, trigger input >0.9996

77 dBc typ. 83 dBc typ. 84 dBc typ. <78 dBc, 82 dBc typ. <83 dBc, 87 dBc typ. <85 dBc, 89 dBc typ. 77 dBc typ. 79 dBc typ. 80 dBc typ. <74 dBc, 78 dBc typ. <80 dBc, 84 dBc typ. <83 dBc, 86 dBc typ.

Digital standard WCDMA with option R&S SMIQB43

To NTT DoCoMo 1.0 and ARIB standard 0.0 Modulation and ACP specifications apply at the respective standard frequency ranges and at levels 8 dBm PEP with R&S SMIQ02B/03B 5 dBm PEP with R&S SMIQ04B/06B Frequency Standard Range Modulation General settings Chip rate Standard Range Link direction Sequence length 4.096 Mcps 0.1 Mcps to 7 Mcps uplink and downlink 45 frames without option R&S SMIQB12 150 frames with 1 option R&S SMIQB12 240 frames with 2 options R&S SMIQB12 WCDMA 0.22 cos ( = 0.1 to 0.7), cos ( = 0.1 to 0.7)

1800 MHz to 2200 MHz same as R&S SMIQ QPSK, OQPSK

Baseband filter Standard Other filters

Vector Signal Generator R&S SMIQ Specifications

15

Code channels and spreading Number

Multicode operation Code channel power Short code Range LMS Long code Initial value uplink Initial value downlink Time offset Physical channel with frame structure Link direction Downlink channels

4 channels with different power 8 channels, 1 channel with different power and 7 channels with equal power mode 15: 15 channels with equal power yes 0.0 dB to 30 dB selectable for each code channel 0 to 127 1 to FF hex selectable for each code channel 0 to 1FFFFFFFFFF hex 0 to 3FFFF hex 0 to 40959 chips (1 radio frame) downlink, uplink, uplink IQ-multiplexed to ARIB 0.0 perch 1, common control 64 ksps sample rate, dedicated channel with 32, 64, 128, 256, 512, 1024 ksps sample rate common control 64 ksps sample rate, dedicated channel with 32, 64, 128, 256, 512, 1024 ksps sample rate dedicated control channel with 16 ksps sample rate, dedicated data channel with 16, 32, 64, 128, 256, 512, 1024 ksps sample rate time offset, separately adjustable for each code channel 0 to 1 radio frame 1 symbol PRBS, 291, 2111,2151, 2161 programmable data memory 00, 11, alternating, programmable data memory chip clock, input and output outputs for slot, frame clock or marker for repetition of chip sequence trigger input <2%, 1.5% typ. <3%, 1.8% typ. 67 dBc typ. 70 dBc typ.
8) 8)

mode 4: mode 8:

Uplink channels Uplink channels (ARIB)

Data offset Range offset Resolution offset Internal modulation data DATA field TPC field Synchronization signals

Error vector magnitude, rms with option R&S SMIQB47, IQ filter 2.5 MHz Adjacent-channel power, 1 DTCH Offset 5 MHz, low distortion output mode Offset 10 MHz, low noise output mode With option R&S SMIQB47, IQ filter 2.5 MHz Offset 5 MHz, low distortion output mode Offset 10 MHz, low noise output mode

<65 dBc, 70 dBc typ. <71 dBc, 74 dBc typ.

8) 8)

Digital standard WCDMA 3GPP (FDD) with option R&S SMIQB45

To 3GPP standard 4.1.0 (FDD) 3GPP (FDD) version Frequency Standard Range General settings Chip rate Standard Range 3.840 Mcps, 1 Mcps to 5 Mcps 4.1.0 to 3GPP technical specifications TS25.211, TS25.213, TS25.141, TS25.101 and TS25.104 1800 MHz to 2200 MHz same as R&S SMIQ

16

Vector Signal Generator R&S SMIQ Specifications

Link direction Sequence length Baseband filter Standard Other filters Clipping level

uplink (reverse link) and downlink (forward link) 1 to 13 frames cos, = 0.22 cos, ( = 0.1 to 0.99), cos ( = 0.1 to 0.99), user filter Setting of clipping value relative to highest peak in percent. Clipping takes place prior to baseband filtering and reduces the crest factor. The range is 1 to 100 %. up to 512 data channels (plus special channels) divided among up to four base stations (BS) with 128 code channels each up to four mobile stations (MS) each operating in one of modes PRACH only, PCPCH only, DPCCH + DPDCHs Primary Common Pilot Channel 15 ksps, fixed 0, fixed predefined symbols Secondary Common Pilot Channel 15 ksps, fixed 0 to 255 predefined symbols Primary Sync Channel 15 ksps, fixed synchronization code (SC) Secondary Sync Channel 15 ksps, fixed synchronization code (SC) Primary Common Control Physical Channel 15 ksps, fixed 1, fixed data Secondary Common Control Physical Channel 15, 30, 60, 120, 240, 480, 960 ksps depending on symbol rate, 0 to max. 255 data, TFCI, pilot Page Indication Channel 15 ksps, fixed 0 to 255 18, 36, 72, 144 page indicator bits, not used bits Access Preamble Acquisition Indication Channel 15 ksps, fixed 0 to 255 acquisition indicators, empty symbols

Code channels Downlink Uplink Physical channels in downlink P-CPICH Symbol rate Channelization code Slot structure S-CPICH Symbol rate Channelization code Slot structure P-SCH Symbol rate Slot structure S-SCH Symbol rate Slot structure P-CCPCH Symbol rate Channelization code Slot structure S-CCPCH Symbol rate Channelization code Slot structure PICH Symbol rate Channelization code Number of PIs per frame Slot structure AP-AICH Symbol rate Channelization code Slot structure

Vector Signal Generator R&S SMIQ Specifications

17

AICH Symbol rate Channelization code Slot structure PDSCH Symbol rate Channelization code Slot structure DL-DPCCH Symbol rate Channelization code Slot structure DPCH Symbol rate Channelization code Slot structure Physical channels in uplink PRACH Symbol rate Frame structure Preamble part power Data part power Control part power Preamble repetition Signature Access slot Message part length TFCI User data PCPCH Symbol rate Frame structure Preamble part power Data part power Control part power Preamble power step Preamble repetition Signature Access slot Message part length Power control preamble length FBI state FBI pattern User data DPCCH Symbol rate Channelization code DLUL timing offset Slot format FBI state FBI pattern TFCI state TFCI Use TPC for dynamic output Power control Output power control step 18
Vector Signal Generator R&S SMIQ Specifications

Acquisition Indication Channel 15 ksps, fixed 0 to 255 acquisition indicators, empty symbols Physical Downlink Shared Channel 15, 30, 60, 120, 240, 480, 960 ksps depending on symbol rate, 0 to max. 255 data Dedicated Physical Control Channel 7.5 ksps, fixed 0 to 511 TPC, pilot Dedicated Physical Channel 7.5, 15, 30, 60, 120, 240, 480, 960 ksps depending on symbol rate, 0 to max. 511 data 1, TPC, TFCI, data 2, pilot Physical Random Access Channel 15, 30, 60, 120 ksps preamble(s), message part consisting of data and control section 60 dB to 0 dB 60 dB to 0 dB 60 dB to 0 dB 1 to 10 0 to 15 0 to 14 1 or 2 frames 0 to 1023 PRBS: PN9, PN11, PN15, PN16 all 0, all 1 and bit pattern (max. 24 bit long) Physical Common Packet Channel 15, 30, 60, 120, 240, 480, 960 ksps access preamble(s), collision detection preamble, power control preamble, message part consisting of data and control section 60 dB to 0 dB 60 dB to 0 dB 60 dB to 0 dB 0 dB to 10 dB 1 to 10 0 to 15 0 to 14 1 to 10 frames 0 or 8 slots OFF/1 bit/2 bit all 0, all 1 and bit pattern (max. 24 bit long) PRBS: PN9, PN11, PN15, PN16 all 0, all 1 and bit pattern (max. 24 bit long) Dedicated Physical Control Channel 15 ksps, fixed 0, fixed 1024 chips, fixed 0 to 5 OFF/1 bit/2 bit all 0, all 1 and bit pattern (max. 24 bit long) OFF/ON 0 to 1023 OFF/ON if this function is active, the TPC pattern is used to vary the transmit power of the MS code channels versus time 10 dB to +10 dB

DPDCH Overall symbol rate

Active DPDCHs Symbol rate Channelization code Channel power User data Parameters for each base station (BS) State 2nd search code group Scrambling code TFCI state TFCI TPC pattern readout mode

Dedicated Physical Data Channel overall data rate of all uplink DPDCHs 15, 30, 60, 120, 240, 480, 960, 2 x 960, 3 x 960, 4 x 960, 5 x 960, 6 x 960 ksps 1 to 6, depending on overall symbol rate fixed for active DPDCHs, depending on overall symbol rate fixed for active DPDCHs, depending on overall symbol rate 60 dB to 0 dB for all DPDCHs PRBS: PN9, PN11, PN15, PN16 all 0, all 1 and bit pattern (max. 24 bit long) OFF/ON 0 to 63 (depending on scrambling code) 0 to 5FFFF hex or off OFF/ON 0 to 1023 use of TPC pattern: continuous, single + all 0, single + all 1, single + alternating 01, single + alternating 10 OFF/ON if this function is active, the TPC pattern is used to vary the transmit power of the code channels versus time 10 dB to +10 dB OFF/antenna 1/antenna 2 if this function is active, the output signal for antenna 1 or antenna 2 can be generated as defined in the standard OFF/ON PRACH only, PCPCH only, DPCCH + DPDCHs 0 to FF FFFF hex long, short, off all 0, all 1 and bit pattern (max. 24 bit long) use of TPC pattern: continuous, single + all 0, single + all 1, single + alternating 01, single + alternating 10 OFF/ON between 7.5 ksps and 960 ksps, depending on type of physical channel range 0 to max. 511, depending on symbol rate and type of physical channel 60 dB to 0 dB PRBS: PN9, PN11, PN15, PN16 all 0, all 1 and bit pattern (max. 24 bit long) separately adjustable for each code channel 0 to 150 (in units of 256 chips) 2, 4, 8, 16 bit depending on symbol rate all 0, all 1 and bit pattern (max. 24 bit long) OFF/ON

Use TPC for dynamic output power control

Output power control step Transmit diversity

Parameter for each mobile station (MS) State Mode Scrambling code Scrambling code mode TPC pattern TPC pattern readout mode

Parameters for each downlink code channel, independently selectable State Symbol rate Channelization code Power User data Timing offset Pilot length TPC pattern Multicode state

Vector Signal Generator R&S SMIQ Specifications

19

Assistant functions to facilitate operation Test models Downlink test model 1 with 16/32/64 channels test model 2 test model 3 with 16/32 channels test model 4 DPCCH + 1 DPDCH at 60 ksps sample rate DPCCH + 1 DPDCH at 960 ksps sample rate generation of complex signal scenarios in downlink with parameterizable default settings selectable parameters: use and symbol rate of special channels (for synchronization of mobile), number and symbol rate of data channels, crest factor: minimal/average/worst common configuration of data channels of BS channel table; selectable parameters, partly with start value and step size: range of data channels to be set, symbol rate, channelization code with step size, channel power with step size, data, TPC, timing offset with step size, multicode state, state adopting the configuration of a BS for another BS/MS for the definition of multi-BS/MS scenarios or BS signals with more than 128 channels parameters: source and destination of copying, channelization code offset for simple definition of BS signals with more than 128 channels and continuous channelization codes elimination of code channel overlapping in code domain (domain conflicts) occurring in a BS/MS

Uplink (not standardized) Parameterizable predefined settings

Multichannel edit

Copy BS/MS

Resolve domain conflicts

Graphic displays Domain conflicts Display of domain conflicts (overlapping of code channels in code domain) in the lines concerned of the channel tables. The code domain occupied by the code channels involved in the conflict can also be displayed. Display of code domain occupied by current BS. Domain areas in which conflicts occur are highlighted. The distribution of code channels in the code domain as well as channel powers are shown qualitatively. Display of all active channels of a BS versus the channel table index. The powers of the code channels are shown qualitatively. Display of complementary cumulative distribution function of current signal. This function gives the probability of the magnitudes of complex IQ samples exceeding a predefined threshold. Together with the current CCDF, the CCDFs of the two 3GPP signals last generated can be displayed to observe the effect of parameter changes. The crest factor of the signal can be seen in the CCDF. Display of constellation diagram versus IQ samples of current 3GPP signal. This diagram allows qualitative assessment of channel configuration, channel power ratios, and the effect of parameters such as data and data offset.

Code domain

Channel graph CCDF

Constellation diagram

20

Vector Signal Generator R&S SMIQ Specifications

Adjacent-channel power, 1 DPCH (crest factor=5,4 dB) Chip rate 3.84 MHz Without option R&S SMIQB47 Offset 5 MHz, low distortion output mode 67 dBc typ.8 ) Offset 10 MHz, low noise output mode 70 dBc typ. 8 ) With option R&S SMIQB47, IQ filter 2.5 MHz Offset 5 MHz, low distortion output mode Offset 10 MHz, low noise output mode Adjacent-channel power, test model 1, 64 DPCH (crest factor=10,6 dB) Without option R&S SMIQB47 Offset 5 MHz, low distortion output mode Offset 10 MHz, low noise output mode With option R&S SMIQB47, IQ filter 2.5 MHz Offset 5 MHz, low distortion output mode Offset 10 MHz, low noise output mode <65 dBc, 70 dBc typ.8 ) <71 dBc, 74 dBc typ.8 )

64 dBc typ.8 ) 67 dBc typ.8 ) <64 dBc, 68 dBc typ.8 ) <67 dBc, 70 dBc typ.8 )

Enhanced functions for digital standard WCDMA 3GPP (FDD) with option R&S SMIQB48
3GPP (FDD) version 4.1.0 to 3GPP technical specifications TS25.101, TS25.104, TS25.141, TS25.211 and TS25.213

Option R&S SMIQB45 WCDMA 3GPP is extended by the following functions: Enhanced Channels Channels of WCDMA system in R&S SMIQ that offer enhanced functionality compared with standard channels of option R&S SMIQB45. Can be used in downlink for max. four DPCHs and in uplink for one DPCCH and max. six DPDCHs. All DPCHs or DPDCHs have the same symbol rate. Enhanced functions at a glance: Sequences of up to 1022 frames Realtime BCH with incrementing SFN Data lists for data fields and TPC field External power control Channel coding Bit error insertion Block error insertion Orthogonal channel noise simulation (OCNS) Additional mobile stations Sequences of up to 1022 frames generation of WCDMA signals with length of max. 256 frames with four active enhanced channels and max. 1022 frames with one active enhanced channel continuous measurement of physical bit error rate (without channel coding) on code channel with PN9 data without wraparound problems use of user data (data lists) with externally processed long data sequences for enhanced channels Generation of a realtime downlink BCH (coded P-CCPCH) with incrementing system frame number (0 to 4094). BCH can be combined with all reference measurement channels (bit rate 12.2 kbps, 64 kbps, 144 kbps, 384 kbps) or AMR of 12.2 kbps bit rate. Max. sequence length: RMC 12.2 kbps 2044 frames RMC 64 kbps 512 frames RMC 144 kbps 512 frames RMC 384 kbps 512 frames AMR 12.2 kbps 2044 frames receiver and performance tests to TS25.101 test of mobile synchronization to BS signal combined with: continuous measurement of DTCH and DCCH bit and block error rate using PN9 data
Vector Signal Generator R&S SMIQ Specifications

Applications

Realtime BCH with incrementing SFN

Application

21

Data lists for data fields and TPC field

For the enhanced channels, the data fields and the transmit power control (TPC) field of the slots can be filled from data lists. This allows the use of externally precoded data or the generation of long power control profiles for the DUT. measurement of UE power control steps measurement of UE max. output power Variation of output power of max. 4 enhanced channels in realtime via external control line. The power of all active enhanced channels can be increased or decreased jointly by means of a TTL signal. 0.25 dB to 30 dB 0 dB to 30 dB 0 dB to 30 dB 60 dB to 0 dB OFF; UP; DOWN current output power (differential power relative to start power) of channels with external power control shown by bargraph test of SIR based closed loop power control Coding of up to four enhanced channels in accordance with definition of reference measurement channels given in TS25.101, TS25.104 and TS25.141. In addition, AMR speech 12.2 kbps to TS25.944 and RACH/CPCH (TB size 168 bit or 360 bit, data PN9 fixed) to TS25.141 are supported. Common coding scheme and symbol rate for all enhanced channels. uplink reference measurement channel for 12.2 kbps, 64 kbps, 144 kbps, 384 kbps downlink reference measurement channel for 12.2 kbps, 64 kbps, 144 kbps, 384 kbps CRC attachment tail bit attachment convolutional coding or turbo coding, depending on symbol rate 1st interleaving radio frame segmentation rate matching 2nd interleaving

Applications External power control

Common parameters Power step Power up range Power down range Parameters for each enhanced channel Start power Power control Graphic display Application Channel coding

Implemented reference measurement channels

Channel coding structure

Sequence length of coded signal 4 enhanced channels 1 enhanced channel Applications up to 256 frames (10 ms each) up to 1022 frames (10 ms each) bit error rate (BER) measurements to TS25.101/104 (radio transmission and reception), eg: blocking characteristics spurious response intermodulation characteristics block error rate (BLER) measurements to TS25.101/104 (radio transmission and reception), eg: demodulation of dedicated channel under static propagation conditions (in conjunction with R&S SMIQB17) demodulation of dedicated channel under multipath fading propagation conditions (in conjunction with R&S SMIQB14 and -B17) test of receiver decoder

22

Vector Signal Generator R&S SMIQ Specifications

Bit error insertion

generation of bit errors by impairment of data stream, either before coding in case of active channel coding, or otherwise at the physical layer 101 to 107 with display of resulting BER verification of internal BER calculation to TS25.141 (BS conformance testing) generation of block errors by impairment of CRC during coding of enhanced channels 101 to 104 with display of resulting BLER verification of internal BLER calculation to TS25.141 (BS conformance testing) Simulation of orthogonal background or interference channels for enhanced channels of a base station. If this feature is activated, 16 DPCHs according to TS25.241, 4.1.0, table C.6 are added. The total power of the OCNS part is adjusted automatically in order to achieve a total power of 0 dB. test of mobile receiver under realistic conditions measurement of maximum input level to TS25.101 Simulation of up to 64 mobile stations in addition to the four userconfigurable mobile stations of option R&S SMIQB45. The scrambling codes of the additional mobiles differ from one another. 1 to 64 1 to 1000 hex 20 to 20 dB base station test under realistic receiving conditions

Parameter Bit error rate (nominal BER) Application Block error insertion Parameter Block error rate (nominal BLER) Application Orthogonal channel noise simulation (OCNS)

Applications Additional mobile stations

Parameters Number of additional MS Scrambling code step Power offset Applications

Requirements for installation of option R&S SMIQB48 R&S SMIQxxB with options R&S SMIQB20, R&S SMIQB45, R&S SMIQB11. Maximum sequence length of enhanced channels requires maximum memory extension of data generator, ie two options R&S SMIQB12.

Arbitrary waveform generator with option R&S SMIQB60

Waveform memory, interpolation Output memory Length of waveform

1 to 524216 in steps of one sample

Note: The specified waveform length cannot be directly compared with the relevant data of conventional ARB generators. In R&S SMIQB60, the oversampling needed for suppressing repetitive spectra by means of the analog filter is effected automatically and in realtime by way of hardware interpolation, ie the stored waveform is not extended by the oversampling factor. For W-CDMA signals, for example, oversampling of only 1.62 is needed. This compares with a conventional ARB with oversampling of 4, meaning that R&S SMIQB60 output memory capacity corresponds to 1.25 Msamples. Resolution Loading time for 512k I/Q samples Nonvolatile memory Number of blocks Block size Interpolation Interpolation bandwidth (0.1dB) Repetitive spectra suppression through analog filter 12 bit 4s 22 (one waveform occupies at least one block) 65527 0.375 x clock rate >70 dB

Vector Signal Generator R&S SMIQ Specifications

23

Clock generation Clock rate Resolution Clock mode Error Signal output Channels Output impedance Output level (EMF, peak) Normal mode Manual mode Level difference between channels DC offset Frequency response Magnitude up to 12 MHz up to 10 MHz Group delay up to 10 MHz I/Q imbalance Magnitude up to 10 MHz Group delay up to 10 MHz SFDR (sinewave 1 MHz, clock 4 MHz, measurement range up to 12 MHz) Trigger Trigger modes Trigger source External trigger input Externe trigger frequency Externer trigger delay range Externer trigger inhibit range Pulse width Trigger outputs Number Delay On time Off time Level Graphic displays CCDF

1 kHz to 40 MHz 0.001 Hz internal or external <242 related to reference frequency 2 (I and Q) 50 I 2 + Q 2 = 1V 6 dB to 0 dB referred to 1 V, setting range up to +3 dB <0.2% at 1 kHz 3 ) <54 dB in normal mode 3 )

<1 dB 0.1 dB typ. 1 ns typ.

0.05 dB typ. 0.5 ns typ. >60 dB auto, retrig, armed auto, armed retrig internal or external threshold 2.5 V to 2.5 V, impedance 1 k / 50 <10 MHz 0 to 216 samples 0 to 226 samples >50 ns 2 0 to 524216 samples 1 to 524215 samples 1 to 524215 samples TTL determination and graphic display of CCDF of waveform loaded into output memory; CCDF also serves for crest factor determination. The CCDF traces of the three waveforms last loaded can be displayed simultaneously.

Operation with WinIQSIM WinIQSIM is a Windows software that allows a wide variety of I and Q baseband signals to be calculated on a PC (see WinIQSIM data sheet PD 0757.6940). From version 3.30, the software supports downloading of waveforms into R&S SMIQ and operation of option R&S SMIQB60 from a PC.

24

Vector Signal Generator R&S SMIQ Specifications

Software options R&S SMIQK11 to -K18

For specifications of digital standards with R&S WinIQSIM and R&S SMIQB60, R&S SMIQK11 to -K18 please refer to the WinIQSIM data sheet PD 0757.6940

Simultaneous modulation
Any combination is possible with the following exceptions: Simultaneous FM and M Simultaneous digital modulation and vector modulation

Overview of digital TDMA standards

The table below summarizes the key data for the digital TDMA standards implemented in R&S SMIQ. Options R&S SMIQB20 and R&S SMIQB11 are required for all standards. GSM (GMSK) Error vector magnitude, rms Phase error (standard), rms Peak value Deviation error, rms Channel spacing/kHz Power density spectrum, typ. resolution BW 30 kHz Offset 200 kHz 400 kHz 600 kHz Adjacent-channel power ratio (ACPR), typ. at adjacent channel at 1st alternate channel at 2nd alternate channel at 3rd alternate channel Burst types N/A <1, 0.3 typ. <3, 1 typ. N/A 200 GSM-EDGE (8PSK) <1.2 %, 0.6 % typ. N/A N/A 200 DECT N/A N/A <1.3 % 1728 NADC <1.2 %, 0.4 % typ. N/A N/A 30 PDC <1.2 %, 0.4 % typ. N/A N/A 25 PHS <1.2 %, 0.4 % typ. N/A N/A 300

34 dB 70 dB 78 dB

34 dB 70 dB 78 dB

N/A

N/A

N/A

N/A

N/A

N/A

N/A

35 dBc 75 dBc 78 dBc

74 dBc 78 dBc

74 dBc 76 dBc

NORMAL, DUMMY, ALL DATA

NORMAL EDGE

FULL (basic), DOUBLE (high capacity), ALL DATA

Up/Down TCH, SYNC, TCH TCH, ALL VOX, (32 kbit and DATA, ALL DATA 16 kbit), Up SHORT SYNC, VOX, ALL DATA

Vector Signal Generator R&S SMIQ Specifications

25

Options for special applications

Fading simulation with options R&S SMIQB14, R&S SMIQB1513 )
RF bandwidth (3 dB) Additional frequency response up to 5 MHz offset from carrier Carrier leakage Setting time after RF frequency change Modes Number of paths and channels with option R&S SMIQB14 with options R&S SMIQB14 and -B15 Path attenuation Range Resolution Error (in range 0 dB to 20 dB) Path delay Range Resolution Error Doppler shift Frequency range Speed range >14 MHz <0.6 dB, <0.4 dB typ. 45 dBc typ. <3 ms external via I and Q modulation inputs, internal with option R&S SMIQB20 6 paths, 1 channel 12 paths, 1 channel, or 6 + 6 paths, 2 channels with second R&S SMIQ through simple retrofit (for instructions see manual) 0 dB to 50 dB 0.1 dB <0.3 dB 0 s to 1600 s 50 ns <5 ns 0.1 Hz to 1600 Hz 9m 0, 03x10 --2
s v min = ----------------------------f RF

9m 479x10 --2 sv = ------------------------max f RF

Example with fRF =1 GHz: vmin= 0.1 km/h, vmax=1724 km/h Resolution 0.1 km/h, m/s, mph Error <0.13% Rayleigh fading Pseudo noise interval Deviation from theoretical CPDF 4 ) for Pavg = 0 dB Path attenuation from 20 dB to + 10 dB Path attenuation from 30 dB to 20 dB Rice fading Power ratio 5 ) Range Resolution Frequency ratio Range Resolution Lognormal fading, Suzuki fading Standard deviation Range Resolution Local constant >372 h <1 dB, <0.3 dB typ. <2 dB, <0.3 dB typ.

30 dB to +30 dB 0.1 dB 1 to +1 0.05

0 dB to 12 dB 1 dB lmin to 200 m

9m 12x10 --sl min = ---------------------f RF

Correlation Magnitude range Resolution Phase range Resolution General data; thermal loading

paths 1 to 6 with paths 7 to 12 0% to 100% 5% 0 to 360 1 specs valid in range 0 C to 45C

26

Vector Signal Generator R&S SMIQ Specifications

Enhanced fading functions for WCDMA 3GPP with option R&S SMIQB49
The following data deviate from the specifications for R&S SMIQB14/R&S SMIQB15: Modes standard fading, fine delay, moving delay, birth-death Setting time after RF frequency change Fine delay mode RF bandwidth Number of paths Profiles Delay Delay resolution Moving delay mode RF bandwidth Number of paths Delay, path 1 Delay, path 2 Delay variation (peak-peak) Variation period Delay step size Profiles Birth-death mode Number of paths Profiles Delay Delay range (birth-death process) Delay grid Hopping dwell 6 ms 4.8 MHz 2 (with R&S SMIQB14), 4 (with R&S SMIQB14 + R&S SMIQB15) Rayleigh, pure Doppler 25 ns to 1637 s 1 ns 4.8 MHz 2 0 to 1000 s (in 50 ns steps)
delay path1+ delay variation(pk-pk) 2 t sin 2 variation period

150 ns to 50 s 10 s to 500 s <1 ns none 2 pure Doppler 5 s to 1000 s 5 s to +5 s (not variable) 1 s (not variable) 100 ms to 5 s

Noise and distortion simulation with option R&S SMIQB1713 )

RF bandwidth (3 dB) Additional frequency response up to 5 MHz offset from carrier Carrier leakage 9 ) Distortion simulator Type of distortion Distortion characteristic AM/AM and AM/M distortion of modulation signal each characteristic programmable by entering up to 30 input values via IEC/IEEE bus or by entering up to five polynomial coefficients 12 bit Gaussian, statistically independent for I and Q 14 dB 30 dB to 30 dB 0.1 dB <0.4 dB <0.4 dB relevant bandwidth for determining noise power N 10 kHz to 10 MHz 1 x 102 white noise <0.8 dB
Vector Signal Generator R&S SMIQ Specifications

>14 MHz <0.6 dB, 0.4 dB typ. 40 dBc typ.

Resolution Noise generator (AWGN) Distribution density Crest factor C/N Range Resolution Error for system bandwidth = symbol rate and C/N <20 dB 3 ) Vector, PSK, QAM modulation FSK, GMSK modulation 10 ) System bandwidth Range Resolution Output spectrum Frequency response up to 0.7 x system bandwidth and 5 MHz offset from carrier at RF output 3 )

27

Bit error rate measurement with option R&S SMIQB21

The data supplied by the DUT are compared with a reference pseudo-random bit sequence. Pseudo-random bit sequences (PRBS) Clock source Clock rate Synchronization time Interface Data Data enable Clock Restart Setup time Hold time Polarity Measurement time Measurement result 29-1, 211-1, 215-1, 216-1, 220-1, 221-1, 223-1 supplied by DUT; a clock pulse is required for each valid bit 100 Hz to 30 MHz 24 clock cycles 9-pin sub-D connector, sub-D/BNC cable supplied with option TTL TTL TTL TTL 10 ns 2 ns normal and inverted (data, clock, data enable) selectable through maximum number of data bits or bit errors (max. 231 bit each), continuous measurement BER in ppm, % or decade values (if selected number of data bits or bit errors is attained) status displays: not synchronized, no clock, no data

Option R&S SMIQB47 for improved adjacent-channel power ratio for WCDMA and CDMA IS-95
Modulation and ACP specifications apply at the respective standard frequency ranges and at levels 8 dBm PEP with R&S SMIQ02B/03B 5 dBm PEP with R&S SMIQ04B/06B Selectable baseband filters to improve ACP values (values see at Digital Standards CDMA/WCDMA) Bandwidth OFF, 850 kHz, 2.5 MHz, 5 MHz WCDMA chiprate 3.84 Mcps /4.096 Mcps, 1DPCH/1DTCH, f = 1800 MHz to 2200 MHz, IQ filter 2.5 MHz Offset 5 MHz, low distortion output mode <65 dBc, 70 dBc typ. 8 ) Offset 10 MHz, low noise output mode <71 dBc, 74 dBc typ. 8 ) IS-95 CDMA, f = 824 MHz to 894 MHz and 1850 MHz to 2000 MHz, IQ filter 850 kHz Reverse link Offset 885 kHz <78 dBc, 82 dBc typ. Offset 1.25 MHz <83 dBc, 87 dBc typ. Offset 1.98 MHz <85 dBc, 89 dBc typ. 9 channels forward link Offset 885 kHz <74 dBc, 78 dBc typ. Offset 1.25 MHz <80 dBc, 84 dBc typ. Offset 1.98 MHz <83 dBc, 86 dBc typ. Error vector magnitude, rms WCDMA chiprate 3.84 Mcps /4.096 Mcps, IQ filter 2.5 MHz IS-95 CDMA IQ filter 850 kHz <3%, 1.8% typ. <2%, 1.3% typ.

28

Vector Signal Generator R&S SMIQ Specifications

Other data
Memory for instrument settings
Memory sequence modes Step time Resolution 50 storable settings automatic, single shot, manual or external trigger 50 ms to 60 s 1 ms

List mode
Frequency and level values can be stored in a list and set in an extremely short time; permissible level variation: 90 dB Modes Max. number of channels Dwell time Resolution automatic, single shot, manual or external trigger 2000 0.5 ms to 1 s 0.1 ms

Remote control
System Command set Connector IEC/IEEE-bus address Interface functions System Command set Connector Baud rate IEC 60625 (IEEE 488) SCPI 1993.0 24-contact Amphenol 0 to 30 SH1, AH1, T6, L4, SR1, RL1, PP1, DC1, DT1, C0 RS 232 SCPI 1993.0 9-contact D-SUB 1.2 kbit/s to 115.2 kbit/s

General data
Power supply Electromagnetic compatibility Immunity to RFI Ambient conditions Operating temperature range Storage temperature range Climatic conditions Mechanical resistance Sinewave vibrations 100 V to 240 V (AC) 10%, 50 Hz to 400 Hz, autosetting to AC supply, max. 300 VA to EN 55011 and EN 61326-2 (EMC directive of EU) 10 V/m 0C to 50C 6 ) to IEC60068 40C to +70C 95% relative humidity at +25C/+40C cyclically, to IEC 60068 5 Hz to 150 Hz, max. 2 g at 55 Hz, max. 0.5 g in range 55 Hz to 150 Hz, to IEC 60068, IEC 61010 and MIL-T-28800D, class 5 10 Hz to 300 Hz, acceleration 1.2 g (rms) 40 g shock spectrum, to MIL-STD-810D, MIL-T-28800D, class 3 and 5 to EN 61010-1 435 mm x 192 mm x 460 mm 25 kg when fully equipped

Random Shock Safety Dimensions (W x H x D) Weight

Vector Signal Generator R&S SMIQ Specifications

29

Ordering information
Vector Signal Generator R&S SMIQ02B 300 kHz to 2.2 GHz R&S SMIQ03B 300 kHz to 3.3 GHz R&S SMIQ04B 300 kHz to 4.4 GHz R&S SMIQ06B 300 kHz to 6.4 GHz Accessories supplied Options Reference Oscillator OCXO FM/M Modulator Data Generator Memory Extension, 32 Mbit Fading Simulator, 6 paths Second Fading Simulator for 12 paths or 2 channels Noise Generator and Distortion Simulator RF and AF Rear Connectors Modulation Coder BER Measurement Digital Standard IS-95 CDMA Digital Standard WCDMA to NTT DoCoMo 1.0, ARIB 0.0 standard Digital Standard WCDMA to 3GPP (FDD) Low ACP for IS-95 CDMA and W-CDMA Extended Functions for WCDMA (3GPP) Extended Fading Functions for WCDMA (3GPP) Arbitrary Waveform Generator incl. R&S WinIQSIM TETRA T1 Simulator Digital Standard IS-95 CDMA (for option R&S SMIQB60) Digital Standard cdma2000 (for option R&S SMIQB60) Digital Standard WCDMA TDD Mode (3GPP) (for option R&S SMIQB60) Digital Standard TD-SCDMA (for option R&S SMIQB60) OFDM Signal Generation, HIPERLAN/2 (for option R&S SMIQB60) Digital Standard 1xEV-DO Digital Standard IEEE 802.11 Digital Standard 3GPPP FDD incl. HSDPA 1125.5555.02 1125.5555.03 1125.5555.04 1125.5555.06 power cable, operating manual R&S R&S R&S R&S R&S R&S R&S R&S R&S R&S R&S R&S R&S R&S R&S R&S R&S R&S R&S R&S R&S R&S R&S SM-B1 SM-B513 ) SMIQB11 SMIQB12 SMIQB1413 ) SMIQB1513 ) SMIQB1713 ) SMIQB19 SMIQB20 SMIQB21 SMIQB42 SMIQB43 SMIQB45 SMIQB47 SMIQB48 SMIQB49 SMIQB60 SMIQ-K8 SMIQK11 SMIQK12 SMIQK13 SMIQK14 SMIQK15 1036.7599.02 1036.8489.02 1085.4502.04 1085.2800.04 1085.4002.02 1085.4402.02 1104.9000.02 1085.2997.02 1125.5190.02 1125.5490.02 1104.7936.02 1104.8032.02 1104.8232.02 1125.5090.02 1105.0587.02 1105.1083.02 1136.4390.02 1136.4290.02 1105.0287.02 1105.0435.02 1105.1231.02 1105.1383.02 1105.1531.02 1154.7800.02 1154.8307.02 1400.5302.02

(for option R&S SMIQB60) R&S SMIQK17 (for option R&S SMIQB60) R&S SMIQK19 (for option R&S SMIQB60) R&S SMIQK20

Hint: R&S SMIQ02B/03B (R&S SMIQ04B/06B) can be equipped with max. three (two) of the following options: R&S SM-B5, R&S SMIQB14, R&S SMIQB15, R&S SMIQB17 Application software PC Software: Generation of data and control lists R&S SMIQ-K1 *) PC Software: Bluetooth signals for R&S SMIQ R&S SMIQ-K5 *) PC Software: User mappings and user filters for R&S SMIQ R&S User Mod *) PC Software: 802.11 packet error rate testing tool *) Recommended extras 19" Adapter Service Kit BNC Adapter for rear panel, D type connector PAR DATA 90 Power Splitter Trolley for Transit Case Transit Case *)
available at www.rohde-schwarz.com

R&S R&S R&S R&S R&S R&S

ZZA-94 SM-Z3 SMIQ-Z5 SMIQ-Z9 ZZK-1 ZZK-944

0396.4905.00 1085.2500.02 1104.8555.02 1104.9580.02 1014.0510.00 1013.9366.00

30

Vector Signal Generator R&S SMIQ Specifications

Service Manual R&S SMIQ Instrument upgrades R&S SMIQ02B to R&S SMIQ03B R&S SMIQ03B to R&S SMIQ04B R&S SMIQ04B to R&S SMIQ06B Modification Kit for Low ACP
1) 2) 3) 4) 5) 6) 7) 8) 9)

1085.2445.24 R&S R&S R&S R&S SMIQU03 SMIQU04 SMIQU06 SMIQU47 1125.5855.03 1125.5855.04 1125.5855.06 1125.5149.02

7) 7) 7)

10 ) 11 ) 12 ) 13 )

PEP = peak envelope power. Data apply to RF5 MHz unless specified otherwise and for ATTENUATOR MODE AUTO function. After 1 hour warmup time and recalibration during 4 hours of operation with temperature variations <5 C. CPDF = cumulative probability distribution function; levels referred to average value of output level. Ratio of discrete and distributed component. Contrast of LCD lower at higher temperature. Factory installation only. Spectrum analyzer settings RBW 30 kHz, VBW 300 kHz, detector RMS. Typical value for QPSK modulation (crest factor approx. 4 dB), referred to average power from sum of carrier and noise power for C/N >5 dB. Carrier leakage deteriorates with increasing crest factor of modulation signal. For symbol rate <300 ksym/s. Spectral components exceeding max. IQ bandwidth will be suppressed. Additional error with ALC OFF <0.3 dB. R&S SMIQ02B/03B (R&S SMIQ04B/06B) can be equipped with up to three (two) of the following options: R&S SM-B5, R&S SMIQB14, R&S SMIQB15, R&S SMIQB17

Certified Quality System

Certified Environmental System

ISO 9001
DQS REG. NO 1954 QM

ISO 14001
DQS REG. NO 1954 UM

Vector Signal Generator R&S SMIQ Specifications

31

ROHDE&SCHWARZ GmbH & Co. KG Mhldorfstrae 15 81671 Mnchen Germany P.O.B. 8014 69 81614 Mnchen Germany Telephone +49894129-0 Internet: www.rohde-schwarz.com CustomerSupport: Tel. +491805124242, Fax +4989 4129-13777, E-mail: CustomerSupport@rohde-schwarz.com

PD 0757.2438.27 Vector Signal Generator R&S SMIQ Specifications Trade names are trademarks of the owners Subject to change

Printed in Germany

0702/0704 (Bi we)