The a4231 is an integrated circuit proximity sensor that can be used with inductive proximity transducers. It has adjustable sensing range and hysteresis using external resistors. It has a wide operating voltage and temperature range and provides overcurrent, overload, and short-circuit protection. The IC includes power and detect LED drivers and has open collector output that can sink up to 150mA.
The a4231 is an integrated circuit proximity sensor that can be used with inductive proximity transducers. It has adjustable sensing range and hysteresis using external resistors. It has a wide operating voltage and temperature range and provides overcurrent, overload, and short-circuit protection. The IC includes power and detect LED drivers and has open collector output that can sink up to 150mA.
The a4231 is an integrated circuit proximity sensor that can be used with inductive proximity transducers. It has adjustable sensing range and hysteresis using external resistors. It has a wide operating voltage and temperature range and provides overcurrent, overload, and short-circuit protection. The IC includes power and detect LED drivers and has open collector output that can sink up to 150mA.
The a4231 is an integrated circuit proximity sensor that can be used with inductive proximity transducers. It has adjustable sensing range and hysteresis using external resistors. It has a wide operating voltage and temperature range and provides overcurrent, overload, and short-circuit protection. The IC includes power and detect LED drivers and has open collector output that can sink up to 150mA.
Copyright:
Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
You are on page 1/ 2
a4231 general features
The a4231 is a proximity sensor integrated circuit to be used with a broad range of inductive single-coiled proximity transducers in proximity detection applications Monolithic IC in bipolar technology User-adjustable sensing range by means of a single external resistor User-adjustable hysteresis (015%) 5.5V35V broad supply voltage range Low-voltage operation possible using stabilised 4.5V5.5V voltage source Internal voltage regulator to improve immunity against fluctuations of supply voltage Broad operating temperature range: -25C...90C Can work with a broad selection of inductive transducers NPN open collector output with guaranteed sink current of 150mA Output overload/over current protection Integrated power-on and detect LED drivers Normally open(NO)/normally closed(NC) select pin Broad range of operating frequencies: 100kHz1MHz Output over current and short-circuit protection Easy temperature compensation of proximity transducers Package QFN-24
Typical application schematic of a proximity sensor/detector
electrical characteristics DC Characteristics The typical values are given for VCC =24V and Tj = 25C unless otherwise specified. # 1 2 3 4 5 6 Symbol IVCC,OFF IVCC,ON VSAT,OUT ILED ILKG ITH,OVL Parameter Supply current Supply current Output saturation voltage LED current Output leakage current Overload threshold current*1) 158 Conditions Output inactive (off) Output active (on) IOUT=150mA 1.0 Min Typ 3.8 8.5 0.50 1.2 <1 190 Max 4.8 12 0.70 1.6 20 220 Unit mA mA V mA A mA
*1) overload threshold current is the level of the output current which triggers the overload protection circuit.
AC and Timing Characteristics The typical values are given for VCC =24V and Tj = 25C unless otherwise specified. # Symbol Parameter 1 2 3 fOSC RN fMAX Operating frequency Conditions Defined by external LC tank Min 0.1 -200 5 kHz CDET=33pF fOSC=100kHz 4 5 6 7 8 10 HW tR tF TS,OVL Hysteresis width Output rise time Output fall time* 2)
Typ
Max 1.0 -2
Unit MHz k
Negative resistance RN= 2RF +/-3% between pin L1 and ground Maximum switching frequency*1) CDET=4.7pF, fOSC=600kHz
2 0 <1.5 <1 50 50 120 120 8.5 250 250 13 15 % s s ms ms pF
Depends on RHYST Load=1kohm Load=1kohm Depends on COVL
Sampling period in overload mode Input capacitance
TSTARTUP Startup time*3) CIN Measured between Pin L1 and AC ground (Pin L2) for fOSC=0.21MHz and |RN| =2100kohm
*1) these are maximum switching frequencies of the IC itself; switching frequencies of sensors may be higher than those given above, *2) the fall time on leaving the start-up interval depends on the load used and can be as long as 10ms, *3) this is the maximum start-up time of the chip itself; this parameter does not reflect performance of a sensor; during the start-up interval the output is inactive (OFF) regardless of the state of the NO/NC pin.
