Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
74 views

Cal Poly Pomona: Nguyen Jason, Andrew Co

This 6-page document describes an experiment on resonant circuits performed by two students. The objective was to observe and calculate the response of series and parallel resonant circuits. Procedures involved constructing these circuits using an inductor, capacitor and resistor, connecting them to a signal generator, and measuring the output voltage and phase angle using an oscilloscope while sweeping the frequency. Tables show the measured values. Calculations determined the resonant frequency, cutoff frequencies, and bandwidth for the series circuit. The conclusion states the experiment was a success, though measurements differed slightly from theoretical values due to experimental error.

Uploaded by

Jason Nguyen
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
74 views

Cal Poly Pomona: Nguyen Jason, Andrew Co

This 6-page document describes an experiment on resonant circuits performed by two students. The objective was to observe and calculate the response of series and parallel resonant circuits. Procedures involved constructing these circuits using an inductor, capacitor and resistor, connecting them to a signal generator, and measuring the output voltage and phase angle using an oscilloscope while sweeping the frequency. Tables show the measured values. Calculations determined the resonant frequency, cutoff frequencies, and bandwidth for the series circuit. The conclusion states the experiment was a success, though measurements differed slightly from theoretical values due to experimental error.

Uploaded by

Jason Nguyen
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

Page 1

CAL POLY POMONA









Nguyen Jason, Andrew Co




EXPERIMENT #7
RESONANT CIRCUITS


EXPERIMENT PERFORMED
22
nd
February 2012
EXPERIMENT DUE DATE
28
th
February 2012







ECE 231L
WEDSNDAY 8:00-10:50 AM
PROFESSOR RICHARD F. SMITH









WINTER 2012





Page 2


Lab
Experiment #7
Resonant Circuits
OBJECTIVE
- The main objective of this experiment is to observe and calculate the response of a
resonant circuit; while gaining experience in plotting series and parallel circuit response and
experience in varying the bandwidth of a resonant circuit.
BACKGROUND
Resonant circuits are used in many applications such as computer circuits, high voltage
generators, and communications devices such as radios. In this laboratory experiment you will
construct and measure the performance of both a series and parallel resonant circuits.
For a series resonant circuit the voltage of the voltage across the resistor will be the same as the
source voltage; however, the voltage across the inductors L and capacitor C will be
considerably higher depending upon the quality factor Q of the circuit. The series circuit is often
called a bandpass circuit. It usually provides voltage gain.
For a parallel circuit, just the opposite is true. The voltage across the inductor and capacitor
will equal the source voltage and the voltage across the resistor will approach zero. This type of
circuit is often called a notch filter. They are often used to drive induction heaters and welders.
This circuit usually provides current gain.
Use the inductor as the output load for the series circuit. If you use the capacitor and you are
able to build a circuit with a very high Q you could damage the capacitor. The series circuit you
will construct is shown in Figure 1. It has a resonant frequency of about 5 KHz.










Page 3


PROCEDURE
The following series and parallel circuits shown were built and connected to our signal generator
to the input. We chose the input to be 5 volts peak and swept the frequency from about two
decades below the resonant frequency to decades above the resonant frequency. We then
observed the output on the oscilloscope and recorded the phase angle and output voltage.











Page 4


LAB MEASUREMENTS AND CALCULATIONS
Table 1. Series Circuit
Frequency
F
out
(kHz)
Phase
Degrees
o
Output Voltage
V
out

3.5 60.8 2.875 V
4.0 309.2 3.750 V
4.5 30.0 4.625 V
5.0 0 5.062 V
5.5 28.84 4.812 V
6.0 45.54 4.188 V
6.5 57.6 3.562 V

Table 2. Parallel Circuit
Frequency
F
out
(kHz)
Phase
Degrees
o
Output Voltage
V
out

3.5 83.0 1.700 V
4.0 -275.0 1.181 V
4.5 -265.0 600 mV
5.0 108.0 118mV
5.5 -78.0 515mV
6.0 78.8 921mV
6.5 76.7 1.328V
7.0 -75.0 1.7V
7.5 -72.0 2 V







Page 5


LAB MEASUREMENTS AND CALCULATIONS CONTINUED

R=100 ohms , L= 0.01 H, C= 100 nF

)
V
omax
occurs at e
o
(center frequency ) =

where X
L
= X
c
e= 2 t f

=31.6 kRad = 5.032 kHz


Cutoff frequency (1)

) (27,015/2PI) = 4.299 kHz


Cutoff frequency (2) =

) (37,015/2PI) = 5.891 kHz


Where

= = 3.1922 kHz
The bandwidth is defined at the frequencies where V
out
drops to 0.707 V
source
or3dB.
That is bandwidth |=e
c1
e
c2
= R/L
Quality factor
















Page 6


CONCLUSION:
Overall, the experiment was a great success where the measurements were close to the
theoretical value. Experimental error did play a factor in the difference between the
measurements and theoretical value because we were unable to take precise readings as the
numbers jumped from a range of values.

You might also like