Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 79 views

    HW25A30A

    Uploaded by

    clauderay
    This document provides instructions for using a brushless electronic speed controller (ESC). It describes the product specifications, features, throttle range setting procedure, normal setting procedure, and program card setting procedure. The ESC has features like low voltage protection, over voltage protection, overheat protection, and lost signal protection. It can be programmed to set values for items like brake settings, battery type, cutoff mode, cutoff threshold, startup mode, and timing.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    HW25A30A

    Uploaded by

    clauderay
    79 views2 pages
    This document provides instructions for using a brushless electronic speed controller (ESC). It describes the product specifications, features, throttle range setting procedure, normal setting procedure, and program card setting procedure. The ESC has features like low voltage protection, over voltage protection, overheat protection, and lost signal protection. It can be programmed to set values for items like brake settings, battery type, cutoff mode, cutoff threshold, startup mode, and timing.

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for using a brushless electronic speed controller (ESC). It describes the product specifications, features, throttle range setting procedure, normal setting procedure, and program card setting procedure. The ESC has features like low voltage protection, over voltage protection, overheat protection, and lost signal protection. It can be programmed to set values for items like brake settings, battery type, cutoff mode, cutoff threshold, startup mode, and timing.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    79 views2 pages

    HW25A30A

    Uploaded by

    clauderay
    This document provides instructions for using a brushless electronic speed controller (ESC). It describes the product specifications, features, throttle range setting procedure, normal setting procedure, and program card setting procedure. The ESC has features like low voltage protection, over voltage protection, overheat protection, and lost signal protection. It can be programmed to set values for items like brake settings, battery type, cutoff mode, cutoff threshold, startup mode, and timing.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    BRUSHLESS ELECTRONIC SPEED CONTROLLER INSTRUCTIONHW25\30A

    Thank you for using DYS Brushless ESC,please read this instruction before use

    A.PRODUCT DESCRIPTION
    1

    Digital electronic design,all adopt import accessories Extreme low output resistance, super current endurance.,totally meet telectric current specs BEC adopt volts regulation independantly,best anti-jamming,lower lost control possibility effectively. Adopt independent PCB to control circuit and power output,prevent circuit to be controlled from power tube temperature going up,there is 2mm space between circuit control and power output,which is good to heat dissipation. Possess temperature protect circuit function. Possess over-volts,lower volts protection function. Possess delicate touch feeling,superior speed linear. Possess throttle memery function,no warning.

    2 3 4 5 6 7 8

    BSPECIFICATIONS
    HW25A/HW30A No loading current:25A/30A Continue current:30A/40A Max current:40A(up to 10s),50A(up to 10s) BEC current:Max 2Amp,linear volts regulator Weight:22g

    CFEATUERS
    1 Safe startup mode:When switch on power,ESC wont be started no matter throttle rocker at which positions,safe and reliable. 2 Low volts protection: When input volts lower than setted value,ESC will reduce or shut down the output automatically,protecting battery effectively. 3 Over volts protection:When input volts higher than rated volts,it emit warning tone,and stop working,self-protecting effectively. 4 Over-heat protection:When the temperature is over 100 celsius degree,the ESC will reduce the output power, protecting ESC effectively. 5 Battery type: Li-xx(Li-ion or Li-poly) / Ni-xx(NiMh or Nicd). 6 Startup mode: normal / soft / super-soft, default is normal startup. 7 Transmitter compatibility:Throttle is being settable,compatible with all transmitter. 8 Security:If lost signal in normal use,the ESC would shut down output,prevent the loss caused by lost control

    DTHROTTLE RANGE SETTING


    This setting is for first time using or a new transmitter is being used. 1Switch on transmitter,push the rocker to the top,connect to ESC power. 2Brushless motor emit a tone shows that power is connected sucessfully. 3Brushless motor emit beep.beepwhich means throttle is at the top. 4Move the rocker to the bottom within 2s,brushless motor emit beep.beep.beep.which means throttle is at the bottom. 5Wait for about 5s,brushless motor emit beep tone indicates that sure setting. 6Now it is done for first time use setting.

    ENORMAL SETTING PROCEDURE


    1 2 3 4 Switch on transmitter,push the rocker to the bottom,and then switch on transmitter. Brushless motor emit one sound which indicate that power supply is OK. Beepbeepbeepseveral sounds should be emitted which means all are ready. Move throttle rocker upwords and go flying. ESC will emit constant warning tone when startup the throttle rocker position is not at the bottom

    FPROGRAM CARD SETTING


    a.Program the ESC with your transmitter(4 steps) 1. Enter program mode 2. Select programmable items 3. Set items value (Programmable value) 4. Exit program mode

    b.Enter program mode


    1) Switch on transmitter, move throttle stick to top , connect the battery pack to ESC 2) Wait for 2 seconds, the motor should emit special tone like beep-beep- 3) Wait for another 5 seconds, special tone likebeep should be emitted, which means program mode is entered

    c.Select programmable items:


    After entering program mode, you will hear 8 tones in a loop with the following sequence. If you move the throttle stick to bottom within 2 seconds after one kind of tones, this item will be selected,or it is failed setting. 1. beep brake (1 short tone) 2. beep-beep- battery type (2 short tone) 3. beep-beep-beep- cutoff mode (3 short tone) 4. beep-beep-beep-beep- cutoff threshold (4 short tone) 5. beep----- startup mode (1 long tone) 6. beep-----beep- timing (1 long 1 short) 7. beep-----beep-beep- set all to default (1 long 2 short) 8. beep-----beep----- exit (2 long tone) Note: 1 long beep----- = 5 short beep-

    d. Set item value (Programmable value)


    You will hear several tones in loop. Set the value matching to a tone by moving throttle stick to top when you hear the tone, then a special tone beep emits, means the value is set and saved. (Keeping the throttle stick at top, you will go back to step 2 and you can select other items; Moving the stick to bottom within 2 seconds will exit program mode directly)

    e. Exit program mode


    There are 2 ways to exit program mode: 1. In step 3, after special tone beep , please move throttle stick to the bottom position within 2 seconds. 2. In step 2, after tonebeep-----beep-----(ie.The item #8), move throttle stick to bottom within 3 seconds.

    GProgram values

    HSimple functions setting


    1 2 3 4 Brake Settingsbrake enabled / brake disabled, default is brake disabled Battery TypeLi-xx(Li-ion or Li-poly) / Ni-xx(NiMh or Nicd)default is Li-xx. Low Voltage Protection Mode(Cutoff Mode) power reducing / power cutoff, default is power reducing. Low Voltage Protection Threshold(Cutoff Threshold) low / medium / high, default is medium cutoff voltage.

    For Li-xx battery number of battery cells are judged automatically / medium / high cutoff voltage for each cell are: 2.6V/2.85V/3.1V. For example: low 3 Cells Li-Poly, when medium cutoff voltage is set, the cutoff voltage is: 2.85*3=8.55V. For Ni-xx battery, low / medium / high cutoff voltages are 0%/45%/60% of the startup voltage (0% means the low voltage cutoff protection function is disabled) . For example: a 10 cells NiMH battery pack, fully charged voltage is 1.44*10=14.4V, when medium cutoff voltage is set, the cutoff voltage is 14.4*45%=6.5V. 5 6 Startup mode: normal / soft / super-soft, default is normal startup. Timing: low / medium / high, default is medium timing. In normal cases, low timing can be used for most motors. But for high efficiency, we 7.

    recommend the Low timing for 2 poles motor and Medium timing for 6 poles and above. For higher speed, High timing could be used. Full Protection Features: Low-voltage cutoff protection / over-heat protection / throttle signal lost protection.

    Http://www.dys.hk

    You might also like