Prf10 Brochure

PRF10 ~ VHF/UHF FM BASE STATION
The PRF10 series is a family of microprocessor controlled, fully synthesized, frequency modulated, VHF and UHF base stations. The PRF10 is extensively used world-wide in diverse and exacting applications due to its superior RF and environmental specification, cost effectiveness and Team Simoco after sales support network. Standard options include AC/DC power supplies with (external) battery backup facilities. The unit can be extensively customised using the PDP, a handheld programmer. All information is held in non-volatile EEPROM. The sophisticated and versatile high performance PRF10 base station is unobtrusive but attractive in appearance and yet rugged enough to meet the demands of a wide range of environments. The all-metal construction ensures minimum case radiation making the PRF10 ideal for use in crowded communal site applications. A raised lid version is available which permits the inclusion of additional hardware options.
PRF10 Base Station
High performance base station Standard variants for all applications Microprocessor controlled-fully programmable Comprehensive control facilities Internal duplexer, isolator and single antenna working options 19 rack or wall mounting options Easily customised
TSD PRF10 - DS
Page 1
TRANSMIITTER TRANSM TTER

The transmitter design is broadband with automatic power circuits to ensure stable RF output over the temperature extremes. The PRF10 is fully protected against excess heatsink temperature by use of progressive power reduction circuits to ensure a predetermined safe area of operation. The power is self-restoring when conditions permit. The RF output power is software controlled.
RECEIIVER RECE VER

The high performance receiver achieves full band performance by employing a self-tracking front-end design.
IINTERNAL DUPLEXER AND IISOLATOR NTERNAL DUPLEXER AND SOLATOR

The PRF10 case is designed to accept a wide range of duplexers and isolators. The full band switching capability of the PRF10 is limited only by the switching bandwidth of the duplexer. The inbuilt isolator is of particular benefit when used in communal sites as a very effective means of reducing interference.
LOCAL//LIINE CONTROL LOCAL L NE CONTROL

The PRF1060 variant is equipped with versatile M80 AC signalling. A range of Team Simoco controllers is available with M80 signalling for use over 2/4 wire 600 ohm or derived circuits permitting Tx key, control of channel change, CTCSS defeat, squelch lift with or without remote supervisories and many other functions.
BATTERY STANDBY OPERATIION BATTERY STANDBY OPERAT ON

All AC variants of a PRF10 include a 12V float charge battery system. An external sealed lead acid battery is automatically charged and powers the base station should the AC supply fail.
SERVIICE AND CUSTOMIISATIION SERV CE AND CUSTOM SAT ON

Any board within the base station can be quickly removed for service or replacement keeping off-air time to a minimum. The engineers handset socket and programming socket are located on the base station motherboard. The Portable Data Programmer (PDP) allows access to the extensive list of PRF10 customisation parameters. This feature enables the PRF10 to meet a very wide range of communications applications. All customisation is stored on non-volatile EEPROM.
Page 2
TSD PRF10 - DS
PRF10 VARIIANTS PRF10 VAR ANTS

The PRF10 is available as either PRF1050 or PRF1060 variants.
Equipment Variant
Application Control Programmable Encode/Decode CTCSS Internal Duplexer 1 Internal Isolator Two Antennae working Antenna Changeover GMSK 8kbps. EST3000-086 Radio ETS300-113 Data Signalling ETS300-279 EMC M80 Line Signalling Facilities Connector Engineers Handset Option Hi-stab. (Special) Option 12V Battery Standby Trunking Interface Cable Equipment Alarms RFW Voting Encoder (Special)
1
PRF1050
Systems Local/Extended Parallel wire
PRF1060
Remote Remote FSK M80 format
Internal duplexer not available for 225-235MHz variants.
TECHNIICAL DATA TECHN CAL DATA

GENERAL SPECIFICATIONS
Operation Modulation Frequency Bands Switching Bandwidth Number Of Channels Channel Spacing Temperature Range Rf Connectors Line I/O Impedance Type Approval Power Supply Frequency Stability Signalling Option Dimensions Weight Full duplex, single frequency simplex, two frequency simplex. Phase F3E E0 66-88 MHz: A9 148-174 MHz: K1 174-208 MHz: K8 225-235 MHz: TM 400-440 MHz: T4 425-450 MHz: U0 440-470 MHz: Full Band (Restricted only by Duplexer and/or Isolator use) 15 - Remote (Using M80 Signalling); 100 - Local 12.5, 20 or 25kHz -30 C to +60 C (Operational); -40 C to +80 C (Storage) Antenna/Transmitter N-Type; Receiver N-Type 600 Balanced ETS300 086 Radio; ETS300 113 Data Signalling; ETS300 279 EMC; Compliant to Low Voltage Directive Input AC; 115V (+15%, -25%) 230V (+15%, -25%) Input DC; 13.6V Nominal (10.8-15.6V) 27.2V Nominal (21.631.2V) External Standby Battery; Typically 12V 24Ah VHF 2ppm or 5ppm,; UHF 2ppm Channel Dependant CTCSS Standard Lid; 88mm(H) X 444mm(W) X 374mm(D) Raised Lid; 134mm(H) X 444mm(W) X 374mm(D) 13kg
TSD PRF10 - DS
Page 3
RECEIVER
Input Impedance Sensitivity Adjacent Channel Selectivity Intermodulation Attenuation Spurious Response Audio Response Hum And Noise Squelch Range Distortion - 600 Output Squelch Rise Time Line Output Level 50 Nominal 0.35Vpd for 12dB SINAD; 0.50Vpd for 20dB Quieting >65dB (12.5kHz), >70dB (25kHz) CEPT 76dB CEPT TR24 >80dB VHF; >85dB UHF +1dB To 3dB of a 6dB per octave de-emphasis characteristic from 300Hz To 3kHz (2.5kHz for 12.5kHz channel spacing) 40dB (Psophometrically Weighted) 12, 15, 18, 21 and 24dB SINAD, (Factory set to 12dB) <5% at 1kHz 60% Deviation 50ms (for <5ms, visit our website see below) 4-Wire, -22dBm to +4dBm ; 2-Wire, -16dBm to 0dBm
TRANSMITTER
Output Impedance Power Output 50 Nominal VHF 1-25w, 55 C Continuous UHF 1-15w, 55 C Continuous 1-25w, 55 C Continuous with fan tray 2.5kHz For 12.5kHz Channel Spacing 4.0kHz For 20kHz Channel Spacing 5.0kHz For 25kHz Channel Spacing 4-Wire, -37dBm to 0dBm ; 2-Wire, -16dBm To 0dBm <5% at 1kHz with 60% Deviation +1dB to 3dB of a 6dB per octave de-emphasis characteristic from 300Hz to 3kHz (2.5kHz for 12.5kHz Channel Spacing) >40dB 10dB without isolator; 40dB with isolator <0.25W to 1gHz; <1W to 2gHz 50ms (for <5ms, visit our website see below) Band (MHz) Separation (MHz) Bandwidth (MHz) 68-88 11.5-15 0.1 68-88 8-11.5 0.1 68-88 4-6 0.1 148-174 4-11 0.15 400-425 4.5-20 0.5 425-450 4.5-20 0.5 450-470 4.5-20 0.5
Deviation Line Input Level Modulation Distortion Modulation Response Fm Noise Reverse Intermodulation Conducted Spurious Emissions Transmitter Rise Time Duplexer Internally Fitted
STANDARD OPTIONS AND ANCILLARIES

Sealed lead acid battery, 12V/24AH (other battery capacities may be used) PDP, Portable Data Programmer Isolator, duplexer or single antenna Isolator retrofit kit Engineers handset and lead Rack (slide out) or wall mounting Test Box, interface and leads Wall mounting fan tray Radio despatcher controller repeater in accordance with (UK) Radio Agency (RFW) licence requirements (CTCSS + DTMF) Receiver calltone 2970Hz
Note: Typical figures based on normal operating conditions. Not all combinations of frequency bands and options are available for every market area. on this or any other Simoco product, visit our web site at:
Team Simoco Field House Uttoxeter Old Road Derby DE1 1NH Tel: +(44) 01332 375500 FAX: +(44) 01332 375666
For additional information www.simocoradio.com
Due to our policy of continuous improvement of our products and services, technical specifications and claims, correct at the time of going to print, may be subject to variation without prior notice. Team Simoco has endeavoured to ensure that the information in this document is correct and fairly stated, but does not accept liability for any error or omission.
Team Simoco 2002
abcde
TSD PRF10 - DS
Page 4

Prf10 Brochure

Uploaded by

Copyright:

Available Formats

Prf10 Brochure

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Prf10 Brochure

Uploaded by

Copyright:

Available Formats

PRF10 ~ VHF/UHF FM BASE STATION

PRF10 Base Station

TRANSMIITTER TRANSM TTER

RECEIIVER RECE VER

IINTERNAL DUPLEXER AND IISOLATOR NTERNAL DUPLEXER AND SOLATOR

LOCAL//LIINE CONTROL LOCAL L NE CONTROL

BATTERY STANDBY OPERATIION BATTERY STANDBY OPERAT ON

SERVIICE AND CUSTOMIISATIION SERV CE AND CUSTOM SAT ON

PRF10 VARIIANTS PRF10 VAR ANTS

Internal duplexer not available for 225-235MHz variants.

TECHNIICAL DATA TECHN CAL DATA

STANDARD OPTIONS AND ANCILLARIES

For additional information www.simocoradio.com

Team Simoco 2002

You might also like