Chapter 4: Walkways
Chapter 4: Walkways
Chapter 4: Walkways
CHAPTER 4: WALKWAYS
Types of Walkways
Pedestrian facilities include sidewalks, trafc signals, crosswalks, refuge islands, pedestrian-scale illumination and benches. Walkways include: SIDEWALKS, located along roadways, separated with a curb and/or planting strip or swale, have a hard, smooth surface. Sidewalks in residential areas are sometimes used by bicyclists, but cities may ban bicycle riding on sidewalks.
PATHS, typically used by pedestrians, cyclists, skaters and joggers (shared-use). It is not realistic to plan and design a path for exclusive pedestrian use, as others will be attracted to the facility. Paths may be unpaved (packed gravel) if they are smooth and rm enough to meet ADA requirements. See Chapter 7 for path design guidelines.
SHOULDERS, which serve pedestrians in many rural areas. The ODOT-recommended shoulder widths are usually adequate to accommodate pedestrians. In rural areas where population densities are too low to justify sidewalks, shoulders should be:
PEDESTRIAN PLAN
4-1
CHAPTER 4: WALKWAYS
Wide enough (6 feet) to accommodate pedestrian and bicycle trafc. See shoulder width table in Chapter 1 for shoulder width guidelines.
Pedestrian Zone
Frontage Zone
Total Width
Standards
Sidewalks The Sidewalk Zone System
The best way to achieve the goal of a clear walking area is to design sidewalks using the zone system. Each zone is a distinct sidewalk area; the 4 zones are: 1. The curb zone; 2. The furniture (or planter) zone; 3. The pedestrian (or walking) zone; and 4. The frontage zone. Each zone has its function, and omitting a zone compromises the quality of the walking experience. The zone system makes it easier to meet the basic ADA requirements for a continuous, smooth, level sidewalk free of obstructions. Its easier to keep the sidewalk level across driveways, place ramps correctly, and all potential obstructions (poles, signs, trees, drinking fountains, benches, etc.) can be placed in the furniture or frontage zones. Separation from the roadway also places pedestrians further from trafc, increasing comfort and security.
The Curb Zone: Most urban streets with sidewalks are typically curbed. A vertical (barrier) curb channelizes drainage and prevents people from parking their cars on the sidewalk. Mountable curbs are not recommended on urban streets, as they make it easier for drivers to park on the sidewalk. The curb zone is also where a sidewalk transitions to the street at a crosswalk or intersection; the design of the gutter pan (apron) is critical for ADA access standards.
Curb zone Curb Apron Furniture Zone Pedestrian zone Sidewalk
Figure 4-2: The curb zones transitions from the street to the sidewalk
The Furniture Zone: The furniture zone is located between the curb and pedestrian zones and can be paved or landscaped. When landscaped it is referred to as the funiture zone. Its easier to meet ADA sidewalk requirements with separated sidewalks. The furniture zone has many functions:
AND
4-2
OREGON BICYCLE
PEDESTRIAN PLAN
CHAPTER 4: WALKWAYS
Pedestrians are separated from trafc, increasing a walker's sense of security and comfort; Street furniture and obstructions (bicycle parking, poles, posts, mailboxes, parking meters, re hydrants, etc.) can be placed out of the walking zone (these objects should not reduce visibility of pedestrians, bicyclists and signs); Room for street trees and other landscaping (plants should be selected that require little maintenance and watering; roots should not buckle sidewalks); The sidewalk can stay level across driveways; Ramps can be placed correctly: sidewalks, curb cuts and crosswalks line up at intersections; and Improved drainage: decreased runoff water, decreasing overall drainage requirements; prevents water in puddles from splashing onto pedestrians; creates a place to store snow removal during the winter. The curb zone and furniture zone should be 5 feet wide or more. Narrower furniture zones (2 feet min) offer some of the advantages listed above. Where constraints preclude the use of the same width throughout a project, the furniture zone can be interrupted and resumed where the constraint ends.
A well organized furniture zone leaves the pedestrian zone clear of obstacles
The Pedestrian Zone: This is where people walk. All planning, design and construction documents should clearly state the walking zone dimension is to be clear of all obstructions. The ODOT standard pedestrian zone width is 6 feet. This width allows two people (including wheelchair users) to walk side by side, or to pass each other comfortably. It also allows two pedestrians to pass a third person without leaving the sidewalk. Where it can be justied and deemed appropriate, the minimum width may be 5 feet, such as on local streets, with adequate separation from the roadway. At no point should the pedestrian zone be less than 4 feet wide at pinch points such as around poles.
Clearance to vertical obstructions (signs, tree limbs, etc.) must be at least 7 feet.
PEDESTRIAN PLAN
4-3
CHAPTER 4: WALKWAYS
substantially separated from a roadway, and the natural contours of the pedestrian zone are different from the alignment of the roadway, or to avoid large obstacles such as mature trees, or other pinch points. Care must be taken to insure the pedestrian zone is free of obstructions.
Figure 4-6: The furniture zone may be eliminated or reduced at pinch points
Cars parked perpendicular or diagonally to sidewalks can reduce the sidewalk width if there is excessive overhang. Wheel stops should be used to prevent narrowing the usable sidewalk width.
Figure 4-5: Sidewalk clearances
The pedestrian zone should be straight, or parallel to the adjacent road when the road naturally curves. Attempts to create meandering sidewalks usually fail because they do not serve the needs of pedestrians, who want to walk in the most direct route possible. The only exceptions should be when a sidewalk is 4-4
OREGON BICYCLE
AND
PEDESTRIAN PLAN
CHAPTER 4: WALKWAYS
Greater sidewalk widths are needed in high pedestrian use areas, such as central business districts, where 10 feet is considered necessary, as the sidewalks are often also used for sidewalk cafs, street furniture, etc. 12 feet to 14 feet sidewalks or greater are common in Central Business Districts.
Sidewalks must not be placed directly adjacent to a high-speed travel lane (45 MPH and above); they should be buffered with a planting strip, a parking lane or a bike lane. In the absence of any separation, sidewalks next to high-speed roadways should be at least 8 feet wide, as the outer two feet are used for poles, sign posts, etc. This results in an effective 6 feet wide walking space and provides 2 feet shy distance from high speed motor vehicle trafc.
4 (min) 2
8 (min) 6
4 (min) 2
The surface should be smooth and uniform. When a sidewalk is paved out to the curb, it is benecial to make a surface distinction between the walking area and the buffer strip; this helps ensure obstacles are placed out of the walking area.
Sidewalk with no buffer
OREGON BICYCLE
AND
PEDESTRIAN PLAN
4-5
CHAPTER 4: WALKWAYS
The Frontage Zone: The frontage zone is located between the pedestrian zone and the right-of-way. It is where sandwich boards, bike racks and other street furniture are placed; it is used by window shoppers, its where people enter and exit buildings.
Frontage zone used for decorative planters A generous frontage zone with seating and bus shelter
The recommended width is 2 feet or greater. An absolute minimum of 1 foot is needed for practical purposes, for example to ensure that adjacent property owners dont erect a fence at the back of walk, or for maintenance personnel to make sidewalk repairs. A 2 foot shy distance is needed from vertical barriers such as buildings, sound walls, retaining walls and fences. In Central Business Districts the frontage zone should be 4 feet or wider to provide space for merchandise, sidewalk cafs, and opening doors. Note: ADA requires that objects protruding from walls (e.g. signs, xtures, telephones, canopies) with their leading edge between 27 inches and 80 inches above the nished sidewalk shall protrude no more than 4 inches into any portion of the public sidewalk. (ADAAG 14.2.2)
4-6
OREGON BICYCLE
AND
PEDESTRIAN PLAN
CHAPTER 4: WALKWAYS
Barrier curb
Surfacing
The preferred material for sidewalks is Portland Cement Concrete (PCC), which provides a smooth, durable nish that is easy to grade. Asphaltic Concrete (A/C) may be used if it can be nished to the same surface smoothness as PCC. A/C is susceptible to breakup by vegetation and has a shorter life expectancy than PCC. Brick pavers can provide an aesthetically pleasing effect if the following concerns are addressed: They should be laid to a great degree of smoothness; They should not have beveled edges; The surface must be slip-resistant when wet; and Long-term maintenance costs should be considered. Ornamental landscape pavers (often beveled or pillowed) should not be used as the primary walking surface; they can be used for aesthetics in the furniture and frontage zones. Sidewalks embellishments can also be achieved by treating concrete with dyes or with decorative scoring.
Bridges
Sidewalks should always be provided on both sides of bridges where pedestrian use can be expected. The minimum width for sidewalks on bridges is 7 feet, to account for two shy distances: from trafc, and from the bridge rail, as some people feel uncomfortable walking close to a high vertical drop. Wider sidewalks should be considered in urban settings with high pedestrian use. The bridge sidewalk must not be narrower than the approach sidewalk. Sidewalks on bridges with design speeds greater than 40 MPH require a vehicle barrier at the curb line.
PEDESTRIAN PLAN
4-7
CHAPTER 4: WALKWAYS
Pedestrian Rail Pedestrian rail should be provided where the sidewalk abuts a steep slope or hazard. The need for pedestrian rail can be eliminated with a shallow slope and soft surface, such as grass.
Pedestrian Rail
Thickness Sidewalks with foot trafc only are normally constructed with 4 inches of PCC on top of a compacted base of crushed rock or sand. At driveways or where the sidewalk can be expected to be driven on by maintenance vehicles 6 inches of PCC is required. Heavy vehicle trafc, such as garbage trucks and emergency vehicles may require 8 inches of PCC to avoid damage. Utility Vaults Water meter covers, man holes and other utility vaults may be located within the pedestrian zone as long as they are smooth, slip resistant and do not have protruding hardware. Tree Well Grates Likewise tree well grates traversable by wheelchairs can be located within the pedestrian zone; however, tree well grates are a hazard to high heel wearers so care should be taken to minimize the extent that tree well grates extend into the pedestrian zone.
Figure 4-12: Pedestrian rail should be used when a sidewalk abuts a serious hazard
4-8
OREGON BICYCLE
PEDESTRIAN PLAN
CHAPTER 4: WALKWAYS
square footprint of a wheelchair to align itself to cross tracks safely, regardless of the skew angle at the crossing. Curving the entire sidewalk to cross tracks at 90 is usually unnecessary. Detectable warnings domes must be placed at the sidewalk/track interface, to alert pedestrians with vision impairments of the presence of tracks.
Railroad Crossings
Sidewalks crossing a railroad are not controlled by the warning gates/arms; they cross behind the gate/arm. The sidewalk width across the tracks should be the same as the approaching sidewalk, or wider. OAR 741-120-0025 (3) states: At crossings equipped with automatic protective devices, sidewalks shall be directed behind the devices at a distance of not less than 5 feet, as measured from the centerline of the signal mast to the nearest edge of the sidewalk. Sidewalks at crossings equipped with automatic protective devices should be constructed as close to the roadway as possible so that users receive visual and auditory warnings of approaching trains. To this end, the far edge of the sidewalk should be no more than 10-12 feet from the centerline of the signal mast. There is no mandate for sidewalks to cross tracks at 90. When a sidewalk crosses tracks at a skew, its usually possible for people in wheelchairs to align themselves at a right angle within the width of a 6 foot sidewalk, even in most cases within a 5 foot sidewalk. Some people prefer to cross at a slight angle, so both casters don't hit the tracks at the same time. For this reason, the best practice is to widen the sidewalk at the grade crossing to allow the 4 foot
OREGON BICYCLE
Railroad Crossing
Paths
Unpaved Paths
In general, the standard width of an unpaved path is the same as for sidewalks. An unpaved path should not be constructed in lieu of a sidewalk. The surface material should be packed hard enough to be usable by wheelchairs, strollers and children on bicycles (the roadway should be designed to accommodate more experienced bicyclists). Recycled pavement grindings provide a suitable material: they are usually inexpensive and easy to grade (this should be done in the summer, when the heat helps pack and bind the grindings).
Paved Paths
See Chapter 7 for standards for shared-use paths.
AND
PEDESTRIAN PLAN
4-9
CHAPTER 4: WALKWAYS
ADA requires an 8 foot by 5 foot landing pad at bus doors. To avoid the choppy effect this creates at bus stops on curbside sidewalks less than 8 feet wide, it is preferable to construct a continuous 8 foot wide sidewalk the length of the bus stop. The wider sidewalk allows passing pedestrians to get by people waiting for a bus.
8 5
At stops in uncurbed areas, the shoulder should be 8 feet wide to provide a landing pad.
Bus stop with shelter in furniture zone Pedestrian crossing paired with transit stop
OREGON BICYCLE
AND
PEDESTRIAN PLAN
CHAPTER 4: WALKWAYS
These goals are easier to meet with separated sidewalks, as the shelter and bike racks can be placed in the furniture zone. Each transit agency may have its own standards for bus shelter pads; walkway construction should be coordinated with local transit agencies to ensure compatibility.
Without extension, right-turning vehicles can use bus pullout as acceleration lane
With extension, right-turning vehicles cannot use bus pullout as acceleration lane; pedestrians and bicyclists are better protected
Bus Pullouts
Where high motor vehicle trafc volumes warrant a bus pullout at an intersection, a far-side location is preferred. The needs of passengers boarding or exiting a bus should not conict with the needs of pedestrians and bicyclists moving through the area. The curb at the corner should not be recessed, as this creates the illusion of an acceleration lane for right-tuning motorists. Placing a curb extension at the corner in line with the rest of the curb helps pedestrian crossing movements, prevents motorists from entering the bus pullout area and reduces conicts with through bicyclists. Each pullout should be designed to meet roadway conditions and bus characteristics. The bus pad should be constructed with concrete pavement to avoid heaving, as buses slow to a stop in the pullout.
OREGON BICYCLE
AND
PEDESTRIAN PLAN
4-11
CHAPTER 4: WALKWAYS
1. Dwell time (passengers can board the bus faster); and 2. The buss ability to accelerate immediately, without waiting to merge back into trafc. These two advantages are substantial improvements to transit operations. A curb extension bus stop may also increase on street parking. The amount of yellow curb required for bus ingress and egress can be greater than the length of a curb extension bus stop. For a more thorough discussion of designing for transit, please consult the Highway Design Manual.
bus shelter
Figure 4-17: Curb extension bus stop Figure 4-18: One crossing serves bus stop in both directions
For a variety of operational reasons, at intersections, farside stops are usually preferred. One advantage is that pedestrians cross in back of the bus. However, transit operators often must place stops nearside, for reasons such as a concentration of users at a nearside corner, or because the bus route makes
AND
4-12
OREGON BICYCLE
PEDESTRIAN PLAN
CHAPTER 4: WALKWAYS
a right turn at that intersection. In all cases the safety and convenience of pedestrians must be a high priority.
driveways, accessible signals and other facilities designed for pedestrians with disabilities. The US Access Board website has the latest guidelines: http://www.access-board.gov/prowac/draft.htm The Oregon DOT Bicycle and Pedestrian program website has links to ODOTs standard drawings: http://www.oregon.gov/ODOT/HWY/BIKEPED/ The purpose of this section is to provide general guidance; please refer to the standard drawings for construction details. It is much easier to meet the ADA requirements with separated sidewalks for several reasons: Obstacles such as poles can be placed in the furniture zone; Driveway aprons and curb ramps can be placed in the furniture zone, leaving the sidewalk level; and Sidewalks, curb cuts and crosswalks line up better at intersections. These and others are reasons why separated sidewalks should always be the design of choice.
Width
The 6 foot standard sidewalk width exceeds the ADA minimum passage requirements. The ADA required pedestrian access route is minimally 4 feet wide with 7 feet vertical clearance. Pinch points, such as at poles or other obstructions must comply with this requirement. The ADA minimum clearance width is not an acceptable continuous sidewalk width.
Grades
Grade standards pertain mostly to separated paths on independent alignments and curb ramps. Where sidewalks are directly adjacent to a roadway, they may follow the grade of the roadway.
PEDESTRIAN PLAN
OREGON BICYCLE
AND
4-13
CHAPTER 4: WALKWAYS
ADA requires that the grade of building access ramps and separated pathways not exceed 5%. A maximum grade of 12:1 (8.33%) is acceptable for a rise of no more than 2.5 feet if a 5 foot long level landing is provided after each 2.5 foot rise. While this may be suitable for short distances, such as a ramp to the entrance of a building, a 12:1 slope followed by a level landing over a long distance creates a choppy effect that is difcult to construct. The overall grade achieved by a conguration of three consecutive rises of 2.5 feet with 5 feet landings in between and at each end is 7.1%. It may be preferable to extend the length of the facility to achieve a constant 5% grade.
Cross-Slope
The maximum allowable cross-slope (needed for drainage) for the pedestrian access route portion of a walkway is 2%. Across driveways, curb ramps and road approaches (in crosswalks, marked or unmarked), a 4 foot minimum wide area must be maintained at 2%. The most frequent interruptions to the level pedestrian access route are at driveways. To facilitate wheelchair movement at driveways, the following techniques prevent an exaggerated warp and cross-slope:
Continuous sidewalk should also be constructed in accordance with the above guidelines. Where terrain is a challenge, sidewalks adjacent to a roadway may be constructed at the same grade as the roadway, but not steeper. Occasional level rest areas are recommended and care must be taken to address slopes at street crossings.
A furniture zone allows sidewalks to remain level, with the driveway grade change occurring in the furniture zone. Reducing the number of accesses reduces the number grade conicts.
4-14
OREGON BICYCLE
AND
PEDESTRIAN PLAN
CHAPTER 4: WALKWAYS
When constraints allow for only minimal sidewalks behind the curb, dipping the entire sidewalk at approaches keeps the cross-slope at a constant grade. This requires pedestrians to go up and down at every driveway, in a roller coaster manner and may create drainage problems on and behind the sidewalk.
1 12
/ max
2% Cross-slope
8.33% max
Where constraints don't allow a furniture zone, wrapping the sidewalk around driveway entrances has a similar effect. Wide sidewalks have enough room to avoid excessively steep driveway slopes; the overall width must be sufcient to avoid an abrupt driveway slope.
Figure 4-23: Entire sidewalk dips at driveway, but beware the roller coaster effect
OREGON BICYCLE
AND
PEDESTRIAN PLAN
4-15
CHAPTER 4: WALKWAYS
There are a number of variations on the above themes: partially lowering the sidewalk, wrapping the sidewalk around the driveway and partially lowering it, etc. Care should always be taken to keep the sidewalk as level as possible and to reduce out of direction travel.
Wide sidewalk accommodates driveway and keeps pedestrian access route level
The other instance where cross-slope can be a concern is on older sidewalks adjacent to buildings. Its not uncommon for the street, the sidewalks and the buildings to have settled over time, at different rates. The sidewalk cross-slope often greatly exceeds 2% in these circumstances. The mitigation measures need only apply to the pedestrian zone, not the furniture or frontage zones; these two zones can be used to make up for the excessive cross-slope.
Figure 4-26: Steeper cross slopes in furniture and frontage zones keep pedestrian zone level
4-16
OREGON BICYCLE
AND
PEDESTRIAN PLAN
CHAPTER 4: WALKWAYS
Ramp Types
The ramp shown in Figure 4-27 works when there is a furniture zone, curb extension, or wide sidewalk; there are many situations in which this design will not work, particularly for narrow curbside sidewalks. The following ramp styles also meet ADA curb ramp requirements. Parallel ramp To be used on narrow curbside sidewalks.
Furniture zone accommodates needed grade changes, keeping pedestrian zone level
Advantages: Easy to construct; and Ramp is full width of sidewalk. Disadvantages: All pedestrians must go down and up ramp; and May cause drainage problems.
Ramps
ADA recommends two ramps per corner at intersections for new construction, as a single diagonal ramp may direct users into the travel way. A single ramp is allowable on retrot projects where circumstances prohibit the installation of two ramps; however, in most cases two ramps can and should be accommodated even on retrot projects. A 4 foot wide passage with a maximum cross slope of 2% must be maintained behind ramps.
5 4
Perpendicular ramp To be used on separated sidewalks (with furniture zone/landscaped buffer). Advantages: Easy to construct;
Standard curb ramp
OREGON BICYCLE
AND
4-17
CHAPTER 4: WALKWAYS
Pedestrians not using ramp may bypass it; and Minimizes impact on landscape area. Disadvantage: Cannot be used in narrow rights-of-way. Note: Wings are required only when furniture zone is traversable, (i.e. when it is paved).
Combination ramp To be used on sidewalks where circumstances prevent construction of standard or parallel ramps.
Figure 4-29: Perpendicular ramp
Advantage: Can be used in constrained areas with difcult grades. Disadvantage: Requires special forming.
Perpendicular ramp with one are To be used on wide curbside sidewalks where an obstacle prevents construction of a are. Advantage: Avoids having to construct are. Disadvantage: Requires special forming.
Figure 4-31: Combination curb ramp
4-18
OREGON BICYCLE
AND
CHAPTER 4: WALKWAYS
Ramp Placement
Placement of the ramp within the intersection is crucial for safety and accessibility. Chapter 6, Intersection Design, covers ramp and crosswalk placement in greater detail; this section discusses the main issues that pertain to accessibility. These rules should be followed: Ramps must be wholly contained within the crosswalk lines (ares may fall outside the crosswalk); Two ramps per corner should be provided, where feasible; Ramps should be placed as close to the intersection as possible; this is made easier by keeping the curb radius tight, and the curb height between two adjacent ramps to no more than 3 inches; and Drainage grates should be provided upstream of ramps to prevent water ponding. The following gures illustrate possible ramp placement scenarios:
Ramp placement on separated sidewalk, NOTE: outside ares are not required.
Curb tight sidewalks By their very nature curb tight sidewalks make placing two ramps difcult. On wide sidewalks with small corner radius (under 25 feet), two ramps can be placed close together.
Separated sidewalks
Sidewalks with furniture zones make ramp placement very simple. Two perpendicular style ramps prolong the sidewalk down to the crosswalk; ares are not needed where the furniture zone is landscaped.
On larger radius curves, the ramps (and crosswalks) will be placed further apart. In this case, two parallel ramps work well on curbside sidewalks. In both cases, limiting the curb height (3 inches min curb exposures) between the two ramps brings them closer together.
Figure 4-32: Ramp placement, sidewalk with furniture zone
OREGON BICYCLE
AND
PEDESTRIAN PLAN
4-19
CHAPTER 4: WALKWAYS
In constrained circumstances, such as against existing buildings, one ramp may be the only option. A 4 foot setback must be provided where the crosswalks meet, so a person using the ramps in a wheelchair can reorient himself in the crosswalk, not the travel lanes. This design is the least desirable, as people in wheelchairs must take a circuitous route to cross the street in either direction.
Cafe
80 Post Projection 4 Desirab Desirable 12 Max Wall Projection 4 Max
PROTECTED ZONE
27
Figure 4-36: Blind pedestrian with clearances Figure 4-35: Single ramp placement on constrained sidewalk
In all cases, reducing the curb radius makes it easier to place ramps so they line up with the sidewalks and crosswalks.
Ramp Elements
APWA/ODOT standard drawings and PROWAG, among other resources, provide detailed information on required ramp elements. 4-20
Pedestrians with visual impairments must also be able to locate crosswalks and travel across streets at intersections. The visually impaired may have difculty locating the crosswalks where the crossing points are not readily apparent, for example at a corner with a large radius or diagonal ramp. There are several techniques that enhance the environment for the vision-impaired: Keeping intersections tight and square to limit long and skewed crosswalks;
AND
OREGON BICYCLE
PEDESTRIAN PLAN
CHAPTER 4: WALKWAYS
Placing crosswalks in areas where they are expected (in line with ramps and sidewalks); Keeping crosswalks straight across the street; Providing accessible pedestrian signals; and Using detectable warnings at ramps to identify the transition from the sidewalk to the street. These features are discussed in greater detail in Chapter 6, Intersections.
Awnings
Where buildings are close to the sidewalk, awnings protect pedestrians from the weather and can be a visual enhancement to a shopping district.
Shelters
At bus stops, transfer stations and other locations where pedestrians must wait, a shelter makes the wait more comfortable. People are more likely to ride a bus if they don't have to wait in the rain.
Benches
People walking want to sit down and rest occasionally. In an urban setting, wide sidewalks, furniture zones and curb extensions provide opportunities for placing benches out of the walking zone.
Landscaping
Landscaping can greatly enhance the aesthetic experience for pedestrians, making the walk less stressful or tiring. Landscaping can increase
OREGON BICYCLE
AND
PEDESTRIAN PLAN
4-21
CHAPTER 4: WALKWAYS
the effectiveness of a planting strip as a buffer between travel lanes and sidewalks, as well as mask features such as sound walls. Choosing appropriate plants and ground preparation are important. The following guidelines should be considered: Plants should be adapted to the local climate and t the context; they should survive without protection or intensive irrigation, and should require minimal maintenance, to reduce long-term costs. Plants must have growth patterns that do not obscure pedestrians from motor vehicles, especially at crossing locations, nor must they obscure signs. Plants should not have roots that could buckle and break sidewalks (root barriers can prevent buckling); the soil should be loosened and treated with mulch deep enough so plants can spread their roots downward, rather than sideways into the walk area. Planting strips should be wide enough to accommodate plants grown to mature size.
Other Considerations
Driveways
Accesses to private property can be built as conventional driveways, or with designs that resemble street intersections. For pedestrian safety and comfort, the conventional driveway type is preferred, as motorists must slow down when crossing the driveway, and the right of way is clearly established, as motorists cross a sidewalk. Intersection-type driveways can disadvantage pedestrians as motorists can negotiate the turn at faster speeds, and the right of way is not as clearly established, the driveway and roadway appear continuous.
Drinking Water Fountains & Public Restrooms Drinking water fountains and public restrooms make it easier for pedestrians to be outdoors for a long time and to walk long distances without 4-22
OREGON BICYCLE
AND
PEDESTRIAN PLAN
CHAPTER 4: WALKWAYS
Where an intersection-style driveway is used (such as to implement a right-in, right-out policy), the following techniques can be used to alleviate the above concerns: The street surface material should not carry across the driveway - rather, the sidewalk should carry across the driveway at sidewalk height, so motorists know they are entering a pedestrian area; The curb radius should be kept as tight as possible; Driveway widths should be the minimum needed to accommodate entering and exiting vehicles; and Where the volume of turning vehicles is high, right-turn channelization should be considered, to remove slower turning vehicles from the trafc ow, allowing them to stop for pedestrians. A trafc signal should be considered where the turning movements are very high.
Commercial right-in, right-out driveway. NOTE: truncated domes are used ONLY at commercial style driveways.
Commercial driveway with wrapped, level sidewalk and pork chop island
Alleys
Alleys are often surfaced with the same paving material as the roadway, so drivers may not realize they are crossing a sidewalk when they exit an alley. Alleys present problems for pedestrians if they are not noticed by exiting drivers. Several measures can improve pedestrian visibility: Designing alleys like driveways, by continuing the sidewalk grade and surface design (texture and color) across the alley, so motorists know they are entering a pedestrian zone; and
OREGON BICYCLE
AND
PEDESTRIAN PLAN
4-23
CHAPTER 4: WALKWAYS
Placing stop signs or a speed hump before the front of a vehicle protrudes onto the sidewalk.
building speed bump
Most walking trips are short, and the pedestrian's line of sight is lower, so developing pedestrian-scale waynding signs that lead to destinations within walking distance can improve the walkability of an area. Signs can assist pedestrians new to the area, or residents who may not realize that the best route on foot is shorter or different than what they are used to driving. Examples of key destinations to include are libraries, schools, museums, recreation centers, shopping districts, city services, etc. No standards have been developed yet for pedestrian directional signs. Signs should be unobtrusive, easy to read and aesthetic. This example gives distances in blocks; other measures could be average walking time. Distances in miles are not very meaningful to pedestrians.
building
Signs
Walkways generally require little signing. Most regulatory and warning signs are directed at motor vehicle trafc. See chapters on street crossings and intersections for signs required in those situations.
Figure 4-41:D1-3b
Directional/Waynding Signs
Signs intended primarily for motorists often do not serve pedestrians well. For example directional signs are typically large, mounted fairly high, and indicate destinations relatively far away; on one-way streets, street name signs are often mounted only in the direction facing motor vehicle trafc, yet pedestrians approach from all directions. 4-24
OREGON BICYCLE
AND
Street Signs
Most street signs adequately serve pedestrians. But street signs on one-way streets often face only motor vehicle trafc. Adding lower level streets signs facing both ways helps pedestrians walking against the direction of trafc, so they can see the names of crossstreets. On two-way streets, signs mounted
PEDESTRIAN PLAN
CHAPTER 4: WALKWAYS
high on mast arms over the roadway should also be supplemented with conventional, smaller signs on the street corners.
street in a semi-rural or suburban environment. Though it adds some aesthetic value, and offers possibilities to add creative landscaping touches, the results are often quite different: Most pedestrians prefer to walk directly, in a straight line; Construction costs are higher, due to the need for special forms; Long-term maintenance costs are higher, as its more difcult to maintain a curved edge than a straight edge; and Once the novelty has worn off, meandering sidewalks are often the object of ridicule and even resentment when the public realizes funds were spent on a sidewalk that doesn't serve users well.
Practices to be Avoided
Meandering Sidewalks
Meandering sidewalks are used in several scenarios: 1. Sidewalks can meander to wrap around large obstacles, such as a mature tree or power pole. 2. Sidewalks can meander in topographically constrained areas, and follow the natural contours of the land. Both these approaches are acceptable, even desirable. But sidewalks often meander with the intention of softening the look of a curbed urban
PEDESTRIAN PLAN
4-25
CHAPTER 4: WALKWAYS
4-26
OREGON BICYCLE
AND
PEDESTRIAN PLAN