How Can I Disinfect My Water System

Aquatic Research Laboratory 783 Pearl Street * Oshkosh, WI 54901 Tel: (920) 424-3148 * Fax: (920) 424-1101
How can I disinfect my water system?

Safety: Before you begin, consider safety issues, first and foremost. Electrical: If you undertake this procedure you will be working with both water and dangerous voltages of electricity, a potentially lethal combination. Use extreme caution to protect yourself and others from electrical shock. If you are not familiar with electrical systems, seek help from a licensed professional. If you have necessary knowledge and experience, use the following precautions before and during a disinfection procedure: Turn off the electrical power to the pump at the circuit breaker before removing the well cap. Wear rubber gloves and rubber-soled footwear. After removing the well cap or seal, examine the wires and connections for potential electrical safety hazards. Have any damaged features repaired or replaced. Keep the power off when adding the chlorinated solution into the well. Chemical: the use of chlorine products involves the risk of chlorine gas, which is very damaging to the eyes and lungs and can be deadly in extreme cases. Take the following precautions to protect yourself: Wear protective goggles or a face shield when using a chlorine product. Never mix chlorine and ammonia products. A mixture of these two products will create a concentrated chlorine gas. Stay upwind of your mixing containers and the well. Do not mix or use a chlorine product in an enclosed space like a pumphouse, alcove or well pit. (In fact, do not enter a pit for any reason because there can be a low oxygen level or a buildup of other harmful gases in a pit.) If your well is in a pit, an alcove or in your basement, hire a licensed professional to chlorinate the well. Do not use more bleach for the chlorine solution than the volumes recommended below. Do not drink heavily chlorinated water or bathe or shower in it. Doing so can damage skin and other tissue. Do not leave or store bleach products where children can get them.
Disinfection Procedure
New wells and wells that produce bacteriologically unsafe water should be disinfected according to the following instructions: 1. Close gate valves so the chlorine solution will bypass your water softener and any other water treatment equipment. A strong chlorine solution can damage this equipment. You can disinfect these devices separately using the manufacturers instructions. 2. Calculate the volume of water standing within your well according to the following Volume of water standing within a well= length of water column multiplied by the Volume Factor for your well (Volume Factors are listed below for given well diameters). NOTE: Length of standing water column=total well depth minus depth to the static water level. Volume Factors based well diameter: 2 inch diameter = quart water for each foot of water standing in the well 4 inch diameter = gallon water for each foot of water standing in the well 5 inch diameter = 1 gallon water for each foot of water standing in the well 6 inch diameter = 1 gallons water for each foot of water standing in the well 8 inch diameter = 2 gallons water for each foot of water standing in the well 10 inch diameter = 4 gallons water for each foot of water standing in the well Example: Calculate the volume of water standing within a 6-inch diameter well, 80 feet deep with a static water level of 15 feet.
First there are (80 15) = 65 feet of water standing within the well. The volume of the water standing within this well will then be: [Volume Factor X (80-15)[1.5 gal/ft X 65 ft] = 97.5 gallons of water standing within the well
3. Using water from a known sage and uncontaminated source, add a volume of water - at least as great as the volume of water standing in the well - into clean new garbage cans or other comparable containers. 4. Using the table below, calculate the volume of bleach (sodium hypochlorite) necessary to produce the desired chlorine concentration to disinfect the well and water system. Generally, for most water systems, a concentration of anywhere from 100 to 300 parts per million (ppm) will be adequate to disinfect the well and the plumbing system. (Most household bleaches contain between 5% and 6% available chlorine.) The bleach must be free of additives like fresh scent, algaecides or thickening agents that can chemically contaminate your well.
NOTE: For severe bacterial infestations perhaps involving a biofilm, like an iron or sulfate reducing bacterial slime, more aggressive approaches may be necessary. These approaches include a more concentrated chlorine solution, measures to control the pH of the solution, or the addition of salt (NaCl) or other department approved products. Sometimes it is also necessary to scrub the inside of the well with a chimney brush to help remove slime or mineral buildup that can harbor the bacteria. Contact a licensed well driller or pump installer for these more difficult situations Volume of Bleach To Water Mix Ratio Approximate Chlorine Concentrations quart bleach per 100 gallons water 100ppm 1 quarts bleach per 100 gallons water 200 ppm 2 quarts bleach per 100 gallons water 300m 5. Using this water and the calculated volume of bleach, prepare a chlorine solution that equals or exceeds the volume of water standing within the well. Add the bleach to the water-filled containers at a site upwind and close to the well so you are less likely to breathe the fumes and so you wont have to carry the solution too far. 6. Remove your well cap or seal and add about a half-cup of Department-approved chlorine granules or tablets (calcium hypochlorite) down the well. (These products must also be free of additives.) The granules will disinfect the column of water standing within the well and prevent bacteria from being forced out into the aquifer when you add the large volume of liquid chlorine solution. CAUTION: DO NOT USE GRANULAR OR TABLET CHLORINE PRODUCTS IN THE ARSENIC PROBLEM AREAS OF NORTHEASTERN WISCONSIN!!! 7. Turn off the electrical power and, while wearing eye protection, rubber gloves and rubber-soled shoes, remove the well cap. Make sure you examine pump wires for chafed insulation or missing wire nuts. Have any necessary repairs made to the electrical system. 8. Pour or siphon the chlorine solution down the well, as rapidly as possible, in one continuous pour. 9. Connect a new clean hose to a nearby hose bib (faucet) and turn the electrical power back on. Turn the water on and recirculate the chlorinated solution through the hose and back to the well making sure you rinse the entire inside surface of the casing, all the way down to the water table. 10. Again turn off the electrical power and drain both the pressure tank and water heater. (Doing this will subsequently allow the water from these tanks to be totally replaced by the chlorinated solution.) 11. Turn the electrical power to the pump back on and let the well water refill the pressure tank and water heater
12. Open every one of you water faucets throughout your plumbing system, both inside and outside, until you can smell the chlorine solution at each one. NOTE: For cartridge water filters, replace the cartridge after you have completed the chlorination process and completely flushed the system. To disinfect your water softener, after completion of the chlorination procedure, add about to cup of bleach to the fill tube in the brine tank and set the softener to manually recharge. 13. Turn all water taps off completely and allow the chlorine solution to remain in your well and plumbing system at least overnight, but preferably 24 hours. 14. Flush the chlorine solution from the entire water system by using a hose connected to one of your outside faucets. Run the solution to a location away from your lawn and landscaping because it can damage them. Also make sure the chlorine solution does not get into a stream, river or lake. Chlorine, even in small doses, can kill aquatic life. Do not run the chlorinated solution into your septic system because it may kill the bacteria that biologically breakdown the waste. The extra volume of the solution can also hydraulically overload the system. The flushing process can take a long time. Keep running the water until you can no longer notice a smell of chlorine from any of your faucets or taps. 15. After the chlorine solution has been completely flushed from the system, wait about a week and resample your water to make sure it is bacteriologically safe to drink.
This information came from the Wisconsin Department of Natural Resources.

How Can I Disinfect My Water System

Uploaded by

Copyright:

Available Formats

How Can I Disinfect My Water System

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

How Can I Disinfect My Water System

Uploaded by

Copyright:

Available Formats

Aquatic Research Laboratory 783 Pearl Street * Oshkosh, WI 54901 Tel: (920) 424-3148 * Fax: (920) 424-1101

How can I disinfect my water system?

This information came from the Wisconsin Department of Natural Resources.

You might also like