S100

SPECIFICATIONS - VEHICLE MOUNTED: MODEL S100
A Dynamic Pump in a More Versatile Package

The S100 Series end suction fire pump provides versatility in a smaller package. With a capacity of 2000 GPM (7570 L/min), the S100 Features a dynamic yet compact design, incorporating a ductile iron body with either an aluminum transmission (C20 Series or PA Series) for midship mounting or an aluminum bearing housing for direct drive mounting (pedestal mount). If you dont want to lose power and versatility by going with a smaller pump try the S100. The S100 is also backed by a standard five-year warranty. An optional Total Protection Package (TPP-5) is available. Design Features: The S100 is a single stage, end suction pump that can be mated to a C20 or PA aluminum transmission or equipped with a bearing housing for pedestal mounting. Construction features of the S100 include a ductile iron case, replaceable wear rings, bronze balanced, flame-plated impeller, and a mechanical seal. Pump Specifications: Pump Body: Cast in ductile iron. Double stripping edge volute minimizes radial forces at all flow rates. Intake: 6 inch (150mm) Victaulic or 8 inch (200mm) Victaulic Discharge: 5 inch ANSI flange or an optional 21st Century Manifold (4 in. end flanged manifold with (8) 2-1/2 in. side pads) or an optional 5 in. ANSI to 4 in. ANSI adapter. Impeller: Bronze impeller, balanced mechanically and hydraulically for vibration-free operation and flame-plated to assure longer life despite the presence of abrasives in the water supply. Impeller Shaft and Seal: Stainless steel shaft and impeller nut with spring-loaded mechanical shaft seal. Self-adjusting mechanical seal eliminates leakage and routine maintenance. Wear Rings: Bronze labyrinth-type (reverse-flow) replaceable wear rings increase pump life and keep maintenance costs to a minimum. V-ring: Located on the impeller shaft between mechanical seal and transmission oil seal, the V-ring provides added protection by keeping water and foreign matter out of the bearings. Oil Seals: Single lip, spring-loaded design for lubrication seal and additional bearing protection from dirt and water. Because the Waterous S100 has been designed with versatility in mind, and each unit is custom built to fit your particular requirements, it is best to consult your builder of Waterous equipped apparatus to determine the top performance of this combination with the chassis and engine/transmission of your choice.
Performance: GPM (L/min) 1250 (4750) 1500 (5700) 1750 (6625) 2000 (7570) Industry-Leading Sales and Support When you purchase Waterous equipment, not only do you get quality products, you get quality service. Our expert service technicians are the best in the business and they are always happy to answer any service questions you might have.
Sales/Applications Assistance Phone: 651-450-5234 (Press 3) pumpsales@waterousco.com Service Assistance Phone: 651-450-5200 Fax: 800-488-1228 service@waterousco.com
PSI (bar) 150 (10.3) 150 (10.3) 150 (10.3) 150 (10.3)
Impeller RPM 3315 3430 3565 3700
HP (kW) 162 (121) 187 (139) 216 (161) 251 (187)
2009 Waterous Company www.waterousco.com
125 Hardman Avenue South, South St. Paul, Minnesota 55075-2456 USA Specifications subject to change without notice.
F-2428 Rev: 09/02/09
SPECIFICATIONS - VEHICLE MOUNTED: MODEL S100

Pump Transmission / Bearing Housing
S100C20 and S100PA Transmission Housing: High-strength aluminum Drive Ratios C20: 1.27, 1.41, 1.48, 1.58, 1.69, 1.79, 1.88, 1.97, 2.03, 2.27, 2.46 and 2.73 Drive Ratios PA: 1.71, 1.91, 2.05 Shafts: Drive line shafts made from alloy steel forgings, hardened and ground to size. Drive and Driven Sprockets Made of steel. All sprockets are hardened, and have ground bores. Drive Chain Morse HV ** high-strength involute form chain. Bearings Deep-groove, anti-friction ball bearings give support and proper alignment to the impeller shaft assembly. Bearings are oil-splash lubricated, completely separated from the water being pumped, and protected by a V-ring and oil seals. Passive Lubrication System C20 and PA use a passive lubrication system that eliminates the need for a separate oil pump. Shift Mechanism (C20 Only) Constant-mesh, two-position sliding collar that engages all teeth simultaneously. In-cab controlled pneumatic shift or an optional electric shift. A patented internal locking mechanism provides a positive lock in PUMP or ROAD position.
S100D Bearing Housing Housing Cast in Aluminum Bearings Deep-groove, anti-friction ball bearings give support and proper alignment to the impeller shaft assembly. Bearings are oil-splash lubricated, completely separated from the water being pumped, and protected by a V-ring and oil seals.
Model: S100D
Model: S100PA
Model: S100C20
Accessories & Optional Equipment

The accessories below are available for Waterous S100 pumps. For detailed information about these accessories, request each specification sheet by number.
S100C20, S100PA and S100D

Pressure Control Systems
Intake Relief Valves - Separately Mounted The Waterous intake relief valve is designed to dump excess pressure from the inlet side of the pump. See Intake Relief Valves, F-2192.
S100C20 Only
Power Shift
Pneumatic shift is standard. Pneumatic shift power allows the operator to shift to ROAD or PUMP position by actuating a simple switch or valve. Electric indicating lights signal completion of shift from ROAD to PUMP. See Power Shift, F-1154.
21st Century Manifold

The 21st Century Manifold is designed to be mounted on the S100 discharge flange. It can be orientated for top or side-mount control panels. Flange arrangements and spacing allows for organized horizontal layout plumbing of all discharges and eases the layout of the panel by the apparatus builder. See 21st Century Manifold, F-2478.
Primer
Select an electric rotary vane priming system. All can be factory installed to your C20 Series pump transmission. See Priming Systems, F-2418
Corrosion Protection
Waterous offers replaceable zinc intake screens and anodes to provide corrosion protection. These items are designed to sacrifice the zinc element to galvanic corrosion. Without this protection, galvanic corrosion may damage the iron pump body and fittings.
Electronic Tachometer Sensor

Monitors driveline rotational speed.
Overheat Protection Manager

The OPM consists of an illuminated warning light on the operator's panel whenever the pump approaches an overheat condition. See OPM, F-2422
Drain Valves
Drains all points of the pump simultaneously with the operation of a single control. See Drain Valves, F-1158
Total Protection Package (TPP-5)

The Total Protection Package is a comprehensive warranty that increases your standard warranty to include labor expenses to dismantle, remove and reinstall covered products or parts, F-2626. 2009 Waterous Company www.waterousco.com 125 Hardman Avenue South, South St. Paul, Minnesota 55075-2456 USA Specifications subject to change without notice. F-2428 Rev: 09/02/09

S100

Uploaded by

Copyright:

Available Formats

S100

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

S100

Uploaded by

Copyright:

Available Formats

SPECIFICATIONS - VEHICLE MOUNTED: MODEL S100

A Dynamic Pump in a More Versatile Package

Impeller RPM 3315 3430 3565 3700

HP (kW) 162 (121) 187 (139) 216 (161) 251 (187)

2009 Waterous Company www.waterousco.com

F-2428 Rev: 09/02/09

SPECIFICATIONS - VEHICLE MOUNTED: MODEL S100

Accessories & Optional Equipment

S100C20, S100PA and S100D

21st Century Manifold

Electronic Tachometer Sensor

Overheat Protection Manager

Total Protection Package (TPP-5)

You might also like