INTERNATIONAL ISO
STANDARD 14585
Second edition
2011-02-15
Hexalobular socket pan head tapping
--`,,```,,,,````-`-`,,`,,`,`,,`---
screws
Vis à tôle à tête cylindrique bombée large à six lobes internes
Reference number
ISO 14585:2011(E)
Copyright International Organization for Standardization © ISO 2011
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
ISO 14585:2011(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@[Link]
Web [Link]
--`,,```,,,,````-`-`,,`,,`,`,,`---
Published in Switzerland
ii
Copyright International Organization for Standardization © ISO 2011 – All rights reserved
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
ISO 14585:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 14585 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 10, Product
standards for fasteners.
This second edition cancels and replaces the first edition (ISO 14585:2001), of which it constitutes a minor
revision. It also incorporates Technical Corrigendum ISO 14585:2001/Cor.1:2004.
--`,,```,,,,````-`-`,,`,,`,`,,`---
© ISO for
Copyright International Organization 2011 – All rights reserved
Standardization iii
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
Copyright International Organization for Standardization
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
INTERNATIONAL STANDARD ISO 14585:2011(E)
Hexalobular socket pan head tapping screws
1 Scope
This International Standard specifies the characteristics of hexalobular socket pan head tapping screws with
thread sizes from ST2,9 to ST6,3 inclusive.
If, in special cases, specifications other than those listed in this International Standard are required, they can
be selected from existing International Standards, for example ISO 1478, ISO 2702, ISO 4759-1.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 225, Fasteners — Bolts, screws, studs and nuts — Symbols and descriptions of dimensions
ISO 1478, Tapping screws thread
ISO 2702, Heat-treated steel tapping screws — Mechanical properties
ISO 3269, Fasteners — Acceptance inspection
ISO 4042, Fasteners — Electroplated coatings
ISO 4759-1, Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C
ISO 10664, Hexalobular internal driving feature for bolts and screws
ISO 10683, Fasteners — Non-electrolytically applied zinc flake coatings
--`,,```,,,,````-`-`,,`,,`,`,,`---
© ISO for
Copyright International Organization 2011 – All rights reserved
Standardization 1
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
ISO 14585:2011(E)
3 Dimensions
See Figure 1 and Table 1.
Symbols and descriptions of dimensions are specified in ISO 225.
Type C
--`,,```,,,,````-`-`,,`,,`,`,,`---
Type F
Type R
Figure 1
2
Copyright International Organization for Standardization © ISO 2011 – All rights reserved
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
ISO 14585:2011(E)
Table 1 — Dimensions
Dimensions in millimetres
Thread sizes ST2,9 ST3,5 ST4,2 ST4,8 ST5,5 ST6,3
Pa 1,1 1,3 1,4 1,6 1,8 1,8
a 1,1 1,3 1,4 1,6 1,8 1,8
da max. 3,5 4,1 4,9 5,6 6,3 7,3
nom. = max. 5,6 7,00 8,00 9,50 11,00 12,00
dk
min. 5,3 6,64 7,64 9,14 10,57 11,57
nom. = max. 2,4 2,6 3,1 3,7 4,0 4,6
k
min. 2,15 2,35 2,8 3,4 3,7 4,3
r min. 0,1 0,1 0,2 0,2 0,25 0,25
rf ≈ 5 6 6,5 8 9 10
Type C 2,6 3,2 3,7 4,3 5 6
y ref. Type F 2,1 2,5 2,8 3,2 3,6 3,6
Type R — 2,7 3,2 3,6 4,3 5
Socket No. 10 15 20 25 25 30
A ref. 2,8 3,35 3,95 4,5 4,5 5,6
Hexalobular socket
max. 1,27 1,40 1,80 2,03 2,03 2,42
t
min. 1,01 1,14 1,42 1,65 1,65 2,02
lb
Type C
--`,,```,,,,````-`-`,,`,,`,`,,`---
and Type F
Type R
nom. min. max. min. max.
4,5 3,7 5,3 3,7 4,5 — — — — — —
6,5 5,7 7,3 5,7 6,5 — — — — —
9,5 8,7 10,3 8,7 9,5 — —
13 12,2 13,8 12,2 13,0
16 15,2 16,8 15,2 16,0
19 18,2 19,8 18,2 19,0
22 21,2 22,8 20,7 22,0
25 24,2 25,8 23,7 25,0
32 30,7 33,3 30,7 32,0
38 36,7 39,3 36,7 38,0
45 43,7 46,3 43,5 45,0
50 48,7 51,3 48,5 50,0
NOTE Preferred lengths are the ones between the bold stepped lines.
a P is the pitch of the thread.
b Sizes with lengths marked with a dash (—) in this table cannot be manufactured.
© ISO for
Copyright International Organization 2011 – All rights reserved
Standardization 3
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
ISO 14585:2011(E)
4 Specifications and reference International Standards
See Table 2.
Table 2 — Specifications and reference International Standards
Material Steel, as specified in ISO 2702
Thread International Standard ISO 1478
Mechanical properties International Standard ISO 2702
Product grade A
Tolerances
International Standard ISO 4759-1
Hexalobular socket International Standard ISO 10664
As processed
Requirements for electroplating are specified in ISO 4042.
Finish — Coating Requirements for non-electrolytically applied zinc flake coatings
are specified in ISO 10683.
Additional requirements or other finishes or coatings shall be
agreed between the supplier and the purchaser.
Acceptability Acceptance inspection is specified in ISO 3269.
--`,,```,,,,````-`-`,,`,,`,`,,`---
5 Designation
EXAMPLE A hexalobular socket pan head tapping screw with thread size ST3,5, nominal length l = 16 mm, round
end Type R is designated as follows:
Tapping screw ISO 14585 - ST3,5 × 16 - R
4
Copyright International Organization for Standardization © ISO 2011 – All rights reserved
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
Copyright International Organization for Standardization
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
ISO 14585:2011(E)
ICS 21.060.10
Price based on 4 pages
--`,,```,,,,````-`-`,,`,,`,`,,`---
© ISO 2011
Copyright International – Allforrights
Organization reserved
Standardization
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
