Sarotech Abigs T6 Manual
Sarotech Abigs T6 Manual
Sarotech Abigs T6 Manual
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : This device may not cause harmful interference This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communication Commission(FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/television technician for help. CAUTION! Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the users authority to users authority to operate the player.
CONTENTS
1 Introduction
Multimedia Functions Input/Output Functions Kinds of format to be supported TV Out set-up and change LCD-Display Information Precautions How to handle and other precautions
4
4 5 6 7 8 9 10
Name of each point Top & Front 11 Name of each point Rear side Contents in package Accessories available at shops 12 13 14
Preparation to use
Kinds of HDD to be installed HDD Installation Connecting with PC To create folder and to copy files Disconnecting from PC Connecting to TV with Composite(AV) cable Connecting with Component cable or HDMI connector Connecting with Optical or Coaxial connector Connecting to Network
15
15 16 17 18 19 20 21 22 23
Procedure 15
VIDEO setting change AUDIO setting change ETC(Other) settings NETWORK setting WIRELESS (Auto setting) WIRELESS (Manual setting) WIRELESS (AD-HOC setting) LAN Sharing setting(PC) Network configuration under window 2000 IP Address Setup: Ethernet Network using a direct connection
28 29 30 31 32 34 37 39 40 45
47
47 48 55 57 58 59
5 6
60 61
61 65
A B
Troubleshooting SPECIFICATION
69 73
Introduction
Multimedia Functions
To playback a recorded digital HD file
As this device supports up to 1920 x 1080 progressive scan, you can enjoy playing back a pre-recorded HDTV program by a digital TV set-top box or person digital video contents taken by a HD camcorder with fantastic displaying quality.
-4-
Input/Output Functions
Digital Audio Output and 2CH Downmix
This player can output digital audio signal(decoded signal), as it can decode digital signal(high quality audio sound signal like AC3) into analog signal internally by itself. And, as this device supports 2CH down mix, users who have 2CH speaker only also can enjoy multi channel audio track..
HOST USB2.0 lets you connect with various external USB devices
As this device has two (2) USB2.0 HOST, you can attach various external USB devices such as external HDD, USB memory, digital camera, etc.
-5-
SMI, .SUB, .SRT MP3, WMV, WMA, Ogg Vorbis, AC3, PCM, DTS JPEG, BMP, PNG, GIF
Needed minimum transferring rate Format MPEG1/2 Xvid WMV9 Wired, Wireless LAN
12Mbps 1.5Mbps 8Mbps
USB2.O(HOST)
10Mbps 1.5Mbps 8Mbps
Even though a video file format is corresponding to the above table, the video file may not be played-back properly in case that the resolution and transferring rate of the video file is over specific value. Although a video file format is corresponding to the above table, the video file may not be played-back properly according to the speed(performance) of external USB devices or the speed(performance) of the devices to compose a network environment. Even though video file format is one of the above classification, the file is not played if the file is encoded with GMC or QPEL option. AVI(Audio Video Interleaved) is a container format. This means that it may contain many different combinations of codec. So, even if this player supports most of AVI files, but, there could be AVI files not played back properly by this device Subtitle is supported properly in case only that the file name of subtitle is exactly same as that of the moving picture. The audio file encoded with copy protection technology is not played back properly. Even if this device can playback 2048 x 1352(JPEG), it may not work properly if the JPEG size is over 1920 x 1080.
-6-
Front LED
Reference
Each pressing TV OUT button: PAL(Composite) 480p HDMI 576p HDMI. 480p(Component) 576p(Component)
You can change and select more subdivided TV out mode in SET UP menu In case of no display on TV screen, try pressing TV OUT button several times to fit TV OUT mode
-7-
LCD-Display Information
This section allows you to playback the music file without connecting this device to TV.
Main Menu
All the options of this screen may be chosen by pressing the function button of remote controller and please refer to PART3 Structure of Remote Controller on the usage of remote controller.
This option allows you to see the list of movie or picture file but playback the selected file.
Sub Menu
Select each icon Change the mode of music playback
Refresh Create JUKEBOX Playback JUKEBOX music subsequently Stop played JUKEBOX music Playback previous music from played one In JUKEBOX Playback next music from played one in JUKEBOX Exit the mode Edit JUKEBOX Delete the selected file
-8-
Precautions
Do not drop or give a shock. It may cause serious damage to internal Hard Disk Drive. Do not block a ventilation opening
Do not touch the plug of the AC power cord with wet hands
Keep it away from high temperature, high humidity, nearby magnetic filed and direct sunlight.
Do not try disassembling. It may cause an electric shock, defect or unexpected problem. For installing or changing HDD, you may open the door on bottom side. Keep it unplugged during lightning storms or when unused for long period time.
-9-
Make sure that you have to use the AC adapter supplied together with this device. If not, it may cause unexpected problem like breakdown, fire, etc. In case that this device is used or left in a completely covered and high temperature space(like in a car) for long time, it may cause unexpected problem. Do not see the light of OPTICAL connector directly. It may have a bad effect on your eyes. In case of no use for long time, get rid of battery from remote controller. To clean the exterior of this device, soak a soft cloth in a mild detergent solution diluted with water, tightly squeeze the cloth to remove the excess liquid, wipe the affected area of the exterior, and finish by wiping with a dry cloth. Make sure that this device is not powered off suddenly during its working (playing-back, file transferring, firmware upgrading, etc). In case of sudden power-off during working, you need to check HDD with Windows utility (Scan Disk) after connecting with your PC system. When you try disconnecting the USB cable between this device and your PC system after finishing jobs, make sure to follow USB device safety removal procedure. When try connecting HDD to SATA cable, S-Video cable, HDMI cable, be careful not to give some damage to pins of each connector.
- 10 -
TV OUT Button
11
Component Video Connector (Y / Pb / Pr) USB Host Port Wired LAN Port(RJ-45) Power12V DC S-Video Connector USB Connector for PC e-SATA Interface Port For Wireless Antenna
External IR Receiver Connector Digital Sound Optical Connector Digital Sound Coaxial Connector HDMI Connector
12
Contents in package
Below items are in the package of this product
Unit
Remote Controller
Users Manual
Poewr Cord
A to B USB Cable
Composite AV Cable
Component Video
13
HDMI Cable
LAN Cable
Coaxial Cable
Optical Cable
S-Video Cable
14
Procedure
1. Check whether all accessories are supplied properly. 2. Install HDD(Hard Disk Drive) into this device according to the procedure of HDD installation 3. Connect AC adapter into this device, and connect it with PC through USB cable 4. Power on this device (with power button of top side, or with power button of remote controller) 5. In case that the installed HDD is not formatted, please format it first according to normal HDD format procedure 6. Copy media files in your PC to the HDD of this device. 7. After finishing copying files, disconnect this device from your PC system 8. Connect this device to TV set and(or) to audio system 9. Power on this device and change set-up value in SET-UP menu if needed. It is recommended that it should be rebooted if you set up Network newly 10. Now, you are ready to enjoy this device freely
15
HDD Installation
1. Push the locker to the direction (OPEN ). Open up the HDD door slowly. 2. There is HDD fixture inside. Push it forward(#1) slightly and pull it up(#2).
3. . Insert HDD carefully inside this device laid down slightly to minimize impact to HDD.
CLOSE).
- 16 -
Connecting with PC
To copy files in your PC to this device, follow below procedure.
4. Check whether this device is properly recognized as USB mass storage by clicking and
opening My Computer on Windows.
- 17 -
If the HDD has no partition or the HDD is not formatted, you need to do it first.
We recommend NTFS instead of FAT32. this device supports multi partitions. Note : Primary partition should be over one(1)
For HDD partition, refer to Chapter 6. When you make folder in the HDD of this device, it is recommended that you make folders like MOVIE, MUSIC, PHOTO. And, you copy files to each folder corresponding to kind of file.
- MOVIE folder responds to MOVIE button of remote controller and MOVIE icon of main menu. - MUSIC folder responds to MUSIC button of remote controller and MUSIC icon of main menu. And, PHOTO folder is also same. - You may make any name of folders freely.
In case that file name(folder name) is too long or has so many specific characters, blanks or period marks, the file(folder) may cause some problem.
- In this case, change or reduce file (folder) name.
- 18 -
Disconnecting from PC
When try disconnecting USB cable between this device and PC, make sure to follow below procedure. 1. Do double-click the icon of Safely remove USB.
3. When the message like picture is shown, disconnect USB cable between this device and PC.
- 19 -
The Composite AV cable is needed to connect with normal TV or Video and is for connecting Composite video signal and 2CH audio signal simultaneously.
Connect yellow cable to the Composite connector of this device and to the VIDEO connector of TV set.
Connect red cable to the FRONT-R connector of this device and to the Sound Input(Right) of TV or Audio system.
Connect white cable to the FRONT-L connector of this device and to the Sound Input(Left) of TV or Audio system.
You may refer to cable colors and connector colors. Please do not misunderstand Composite connectors and Component(Y, Pb, Pr) connector which is located on rear side of this device as shown here.
If you want to use digital audio output(Optical, Coaxial), you dont need to connect with red cable and white cable.
In case that your TV set has S-Video input connector, you may enjoy higher display quality by connecting with S-Video cable.(note : As we do not supply S-Video cable, you need to purchase it by yourself from shop)
- 20 -
- 21 -
As the audio output through Optical or Coaxial is digital signal, separate devices like DTS Decoder(or Receiver) is needed additionally. For safety, connect cables after power off this device and audio system. You have to purchase Optical cable or Coaxial cable by yourselves from shop. Make sure that Optical cable is not bent severely. Do not see optical light which comes from Optical connector. It may have a bad effect on your eyes.
- 22 -
Connecting to Network
To connect this device to a network, some equipment is required. Ethernet Network using a direct connection to a PC(IP Address setup)
Connect this device to a PC with a crossed cable. Equipment required. A crossed cable.
Wireless Range.
Radio signals may be reflected by some obstacles or be absorbed by others depends on their construction. Heavy or big media file like HD file or DVD file is not streamed properly with wireless connection.
- 23 -
POWER ON / OFF MOVIE FOLDER HOT KEY MUSIC FOLDER HOT KEY GOTO CLEAR ALL(JUKEBOX) BOOKMARK SLEEP TIMER INFO / CURRENT TIME MUTE STOP RETURN / CANCEL +15 SEC FF / UP REWIND / LEFT OK/SELECTION REWIND -15 SEC/ DOWN BGM ON / OFF PREV. / NEXT FILE ZOOM / SCROLL AUDIO SYNC DVD TITLE / MENU DVD ANGLE
TV OUT KEY
FAST FORWARDING
SLOW PLAYING REPEA (A B) REPEAT / SHUFFLE EJECT (ODD) COLOR SETTING SUB TITLE DUBBING AUDIO
- 24 -
In case of no display.
TV Out mode is originally set as PAL/Composite. If no-display on TV screen after booting up, try changing TV Out mode by pressing TV OUT button of remote controller or on the front side of this device with 2~3seconds time interval.
- 25 -
MUSIC icon
If selecting MUSIC icon, it shows all contents in MUSIC folder of the basic HDD. It will be convenient for you to use or manage files if you make MUSIC folder in the root directory of HDD in advance.
PHOTO icon
If selecting PHOTO icon, it shows all contents in PHOTO folder of the basic HDD. It will be convenient for you to use or manage files if you make PHOTO folder in the root directory of HDD in advance.
USB 1 or 2 icon
In case that some devices are connected to USB HOST ports, these USB Icons are activated. Once activated, those icons can be selected. Otherwise, you can not click or select it.
NETWORK icon
In case that this device is connected to network properly through Wired or Wireless LAN, this icon is activated and can be selected. Otherwise, you can not select it.
- 26 -
SETUP Menu is classified like VIDEO, AUDIO, ETC, NETWORK, WIRELESS, EXIT. You can select each item with Left/Right (, ) button of remote controller or this device. To change setting values, if selecting main item, sub items are listed up. You can select each item with Up/Down(, ) button. After selecting sub item, press OK button. Then, changeable setting values are displayed. Once you select one of changeable setting values with Up/Down(, ) button, press OK button. Then, the value is saved and applied. If you want to go out without changing setting values, press RETURN button before you press OK button for confirming any selected value. Pressing RETURN button, it makes you go to previous step. After completing new setting, you can go back to main menu by pressing RETURN button several times, by pressing SETUP button or selecting EXIT icon.
- 27 -
TV Type
4:3 (for normal TV) 16:9(for Wide TV such as HDTV or Plasma TV
Display
Original(Letter Box) :
Select this option in case of playing a wide movie(16:9) with an ordinary 4:3 TV. There will be margins on the upper and lower sides of the screen.
Pan & Scan : Select this option if you want a wide movie(16:9) to be adjusted fully to the screen of ordinary 4:3 TV. The left/right of the movie is cut, and the margin of top/bottom is disappeared. Full Screen : Select this option if you want to adjust a movie fully to the screen of TV with no consideration of original ratio. In this case, according to the ratio of original movie, displaying size is enlarged upward/downward or to the left/right.
Video Out
Composite/S-Video : In case of connecting with TV through Composite, S-Video or Component 480i output connector. Component(each Mode) : In case of connecting with TV through Component(Y, Pb, Pr) output connector. HDMI (Auto or each Mode ) : In case of connecting with TV through HDMI connector.
By pressing TV OUT button of remote controller or this device several times, you can change TV standard and Video Out mode in order. Standard modes changeable in order is six(6) level.
- 28 -
Audio Channels
2 ch : If selecting this option, it outputs analog audio signal with 2CH. If you use 2CH speaker, please select this option. 5.1 ch : If selecting this option, it outputs analog audio signal with 5.1CH. Without any separate Decoder or Receiver, you can connect with 5.1CH speaker directly
Sound Effects
On : When power off and on this device, sound effect comes out. Off : No sound effect in power on/off..
- 29 -
ETC(Other) settings
In SETUP Menu, if selecting ETC icon, sub items are listed up like below picture.
Slideshow Interval : To control time delay for displaying next picture file during slideshow.
3sec, 5sec, 10sec ~ 60sec (total 9 levels)
OSD Lang. : To change OSD languages. Sub. Color : To change subtitle color when playing back a moving picture.
total nine(9) kinds available.
Sub. Size : To change size of subtitle when playing back a moving picture.
total two(2) kinds(Large/Small) available.
User defined background : To change the background of main menu with other picture file that you want.
You choose a picture file in the basic HDD or in folder through network.
Use default background : To use original background by canceling the user defined background. Factory reset : To clear all values set by user and to initialize this device with values set at factory. Firmware Update: To select firmware bin file and to update with new firmware.
- 30 -
NETWORK setting
The sub option related to network will be displayed by selection of NETWORK icon.
Network Connection : Select either Wired Net. (for the Ethernet connection) or Wireless Net. depending on the type of network connection you want to set up. Connection Status : It shows current network connection status. Address Setup:
DHCP(Auto IP) : IP address will be assigned automatically with using a router. Static IP : IP address should be assigned manually by user with Ethernet networking using a direct connection to the computer. Input the IP address, Netmask and Default gateway.
- 31 -
WIRELESS(Auto setting)
This section shows how to make wireless network setup automatically to communicate with devices under network environment. You dont need to change any setting value manually. AP SEARCH Click AP SEARCH to look for AP available.
List of AP available You can select the AP that you want to use and press OK button.
In case that you set ESSID as hidden or you set Password for your AP.
In case that you set ESSID as hidden or you set password with your AP, you need to enter ESSID name or Password by yourself. For entering ESSID name or Password, this device will show you the specific window.
- 32 -
Check ESSSID
You can make sure whether the setting value(ESSID, Channel, etc) is right or not. The setting values should be match with your wireless router(or AP) or PC. Then, you may press RETURN button to store this setting and exit.
Getting IP address
This device will try to get new IP address from your router. It takes about 30 ~ 60 seconds.
According to network security setting, network status, etc, sometimes it will take 5 ~ 10 seconds for the network icon to be activated. So, you need to wait for some time until the network icon is activated.
- 33 -
WORDING.
The SSID is also referred to as the ESSID or Extended Service Set ID
CHANNEL The 802.11g and b specifications supports up to 14 overlapping channels for radio communication. You can select from AUTO to CH13. The selected channel of this device should be as that of the wireless router or the AP(access point) that you use under network environment.
- 34 -
Wireless Security (Authentication Method) You can set different authentication methods which determine different encryption schemes. There are 6 authentication methods (WEP Auto, WEP SHARED, WEP OPEN, WPAPSK, WPANONE, WPA2PSK).
Encryption algorithm (WEP or WPA) The encryption algorithm determines the authentication method you select.
Relation.
Authentication Method WEP Auto WEP SHARED WEP OPEN WPAPSK WPA NONE WPA2PSK Encryption Algorithm NONE WEP TKIP AES
Encryption (WEP) Encryption (WEP) option should be applied in case that WEP encryption algorithm is used. The encryption setting of this device should be exactly same as that of the wireless router or the AP(access point) you use under network environment.
- 35 -
Encryption(WPA ,Pre-Shared Key) Encryption (WPA) option should be applied in case that TKIP or AES encryption algorithm is used. The encryption key of this device should be exactly same as that of the wireless router or AP(access point) that you use under network environment.
Each manufacturer may use different wording when naming each function. Make your reference for below wordings. ESSID : referred to as SSID or Extended Service Set ID ASCII when WEP key or WPA key input : referred to as Characters HEX when WEP key or WPA key input : referred to as Hexadecimal Wireless security : referred to as Authentication method or Type. Encryption : referred to as Encryption Algorithm or Encryption Type NONE : referred to as NULL WPAPSK : referred to as WPA P-Key, WPA Pre-Shared Key or Network Key Key : referred to as Key Value
- 36 -
WIRELESS setting of this device Go to WIRELESS in SETUP menu and enter the following lists. A B C D E AD HOC. Enter ESSID(ex. abc) Select Channel (ex. Ch11) Select WEP AUTO Select NONE"
Save setting and Return to main To save setting and return to main, press SETUP button on remote controller.
- 37 -
Set IP and Subnet mask with a PC On the PC, select Network connection in the control panel. Open Properties for the network connection that is connected to this device. Select Properties for the Internet protocol (TCP/IP). Select Use the following address Enter the IP address below. IP address : 200.200.0.1 Subnet mask : 255.255.255.0 Click OK
Zero Configuration utility-a Open wireless zero configuration utility and choose a wireless network with same ESSID (ex.abc) that you entered with this device. Click Connect.
Zero Configuration utility-b After connecting successfully, you can browse shared folder with this device. Refresh network list.
If you can not find the ESSID that you entered with this device, please try to click Refresh network list on wireless Network Connection.
- 38 -
NOTE.
If firewalls are set in your PC, it may cause problem for this device to communicate with your PC. So, you need to disable the firewall program in your PC. 1. Click right button of mouse on the folder that you want to share and select Sharing and Security....
2. Check on
Share this
folder on the network. Fill in the box of Share name. And then, click OK and Apply button for confirmation.
- 39 -
3. Then, each shared name will be listed up on screen if this device is connected.
- 40 -
STEP 5 Release the check box on Account is disabled and Apply this setting
- 41 -
STEP 7 Click right button of mouse on the folder that you want to share and select Sharing
STEP 8 Click radio box on Shared this folder and click the Permissions
- 42 -
- 43 -
- 44 -
1. Select Network Connection in the Control Panel. Select the Local Area Connection to be connected with this device and click the right button of mouse. Select Properties.
- 45 -
3. Select Use the following IP address Enter the IP address below. IP address 192.168.0.1 Subnet mask 255.255.255.0
5. Then, start the player, press SETUP button on your remote controller and go to NETWORK section. Select Ethernet on Network Connection and Static IP on Address Setup Then input the following address. IP Address 192.168.0.2 Netmask 255.255.255.0 Default gateway 192.168.0.1 Press SETUP on your remote to exit this menu. Check that NETWORK icon is highlighted on main screen.
- 46 -
JUKEBOX + OK
2. Make PLAYLIST
Select music file and press OK button. Then, each selected file will be stored into PLAYLIST.
- 47 -
4. Reference JUKEBOX function can be used when you do other jobs like Photo Slideshow or Onscreen jobs.
2. Fast searching
In playing a movie file, you can search the position that you want to see by pressing REW, FF button. It supports up to 32X searching. 1 press: 2 press: 3 press: 2X 4X 8X
- 48 -
4. GOTO function In playing DVD, if you pressing GOTO button, you can go to the specific position that you want.
After pressing GOTO button, input the time and press OK button XX : YY : ZZ (H) : (M) : (S)
- 49 -
6. MUTE For sound off, press MUTE button. To clear this function, press MUTE button once again.
- 50 -
10. Multi Subtitle control If the playing movie contains multi subtitle, you can select a subtitle that you want to see by pressing S.TITLE button. To select subtitle, press OK button
2nd ~ 3rd press 11. Multi Audio control If the movie file contains multi audio, you can select an audio that you want by pressing AUDIO button.
- 51 -
12. Enlarging the screen To enlarge screen size, press ZOOM/SCROLL button and control the screen size by pressing directional button().
1st press 13. Scrolling the enlarged screen To move enlarged screen, press ZOOM/SCROLL button once again and move the enlarged screen by pressing directional button().
2nd press
14. Screen Color control To adjust color setting, press PICTURE Button and control Brightness, Saturation and Contrast by pressing directional button().
- 52 -
15. Memorizing a specific position In playing movie file, the current playing position is saved by pressing BOOKMARK button.
16. BOOKMARK list Pressing BOOKMARK button again, the latest Bookmarked List is shown.(Max. 5 lists)
BOOKMARK + or + OK
17. Playback with slow speed This device supports slow playing back function up to 1/32X.
1st press : 1/2X 2nd press : 1/4X 3rd press : 1/8X 4th press : 1/16X 5th press : 1/32X
- 53 -
18. Control subtitle sync If a movie and a subtitle do not match, you can control a subtitle showing time by pressing SYNC button. SYNC + or
1st press 19. Section Repeat Set the beginning point Press A-B button once to select the beginning A- point.
1st press
20. Section Repeat Set the ending point Press A-B button again to select the Ending -B point. A-B section will be repeated. To clear this setting, press A-B button once again.
2nd press *Note : This function is useful for language study or enjoying sports moving picture.
- 54 -
3. Multi Subtitle Language Selection In playing DVD, you can select a subtitle language that you want by pressing S.TITLE button.
- 55 -
4. Multi Dubbing Audio Selection In playing DVD, you can select a dubbing audio that you want by pressing AUDIO button.
5. Return to DVD menu Screen In playing a DVD, you can go to DVD menu screen by pressing TITLE button. When you play DVD again after setting, it starts from stopped position of DVD.
6. GOTO function In playing a movie, you can go to the button. specific position that you want by pressing GOTO
Volume control, color setting and media information are same as Enjoying movie file functions. go next or previous chapter of DVD, use -PAGE+ button.
To
- 56 -
2. How to change Music Play Mode In playing a music file, you can change play mode by pressing REPEAT/SHUFFLE button.
3. M3U and PLS file support This device supports M3U playlist and PLS playlist by created WINAMP. To play these files, music files linked with M3U and PLS should be in same HDD partition.
- 57 -
2. ZOOM / SCROLL of photo You can enlarge the photo with direction keys of remote controller after pushing ZOOM/SCROLL button of remote controller one time.
- 58 -
NOTE
The player supports mass storage device in read only mode only. 3. ODD tray controlling The player controls ODD tray on and off by pressing EJECT button when ODD USD device is connected.
- 59 -
Firmware update
This section explains how to update firmware.
Getting the latest firmware to enjoy the added features and improved function. 1. Firstly, visit the designated website (Please ask the shop where you bought this device). You can download the newest firmware and save it on your PC. 2. Please extract the compressed firmware file and move or copy the file into this device through USB cable. If this device is connected an internal network, installing the newest firmware via internal network is also possible without copying the firmware file into this device. In this case, the firmware file should be stored in the shared folder of PC. 3. Connect this device to a TV and power it on. Click the SETUP button on remote controller and go to ETC setting section of SETUP. 4. Select Firmware update and search the folder where the new firmware file is saved.
*** The screen is an example only. The list will be different according to the firmware you are updating ***
5. Select update file and push OK button on remote controller. 6. Firmware update will start automatically when you select Yes on confirmation message box. 7. this device will power off in 10 sec automatically after update process is completed successfully. 8. Power on this device again, then go to ETC section of SETUP. Select Factory Reset and press OK button for factory reset. And, power it off again. After this, you can enjoy with new firmware.
* Caution !!! While updating, please make sure that this device is not powered off. If powered off while updating, it has not been repaired from customer service center.
- 60 -
2. Type fdisk and click enter. Select Y to enable large disk support.
- 61 -
In case of more than 2 HDDs In case that there are several hard disk drives in your PC, the disk number may be changed. In this case, you can select the number corresponding to each percent (%).
- 62 -
- 63 -
8. Select Y and Enter to use the maximum available size for a Primary DOS Partition.
9. Wait to be finished verifying drive integrity once again and click ESC two times to finish MS-DOS prompt program.
11. After restart, the new hard disk drive will be shown on My Computer. Click the right button of your mouse and select Format to be formatted.
- 64 -
3. Click the next on The initialize and Covert Disk Wizard window.
- 65 -
5. Click the Finish on Completing the initialized and convert Disk Wizard window.
6. Click the right button on your mouse and select the New Partition.
- 66 -
Important
The player works properly with TV in case of Primary partition type only.
- 67 -
11. Select file system and click the next. (FAT32 can not be selected over 32GB HDD).
Important
Do not check Enable file and folder compression.
13. After setup the New Partition Wizard, the new HDD will be formatted automatically. Please wait until 100% formatting is completed.
- 68 -
Troubleshooting
Before contacting Customer Service Center, please check below points first.
2. Much noise on TV screen. Check whether video cable is connected properly and tightly. Check if TV Out mode is matched with your TV, or not. In case that you connect this device to TV indirectly through DVD player or VCR, etc, there may some noise on TV screen. Please connect this device to TV directly. In case there is some moisture inside this device when you move it from cold outside to warm inside, you need to wait for some time until it is conformed to inside temperature. 3. In case that the size of playing picture does not fit to TV screen. As aspect ratio is fixed, please set it properly again in the SET-UP menu..
- 69 -
Check whether stereo cable (A/V cable) is connected properly and tightly between this device and TV set. Check if [MUTE] button is pressed and volume level is set properly Check whether digital audio cable is connected properly and tightly to the audio input connectors of Home Theater System or Audio Amplifier Try changing the value(Down mix or pass through) of Audio Out on SET-UP menu Try changing audio cable with new one.
2. In case of no-sound or bad sound quality when connected with digital audio system Check the Audio channels on SETUP MENU Set as pass through on SETUP menu. Check the status of connection and set up for digital audio system(Refer to the manual of digital audio system) Check whether optical cable or coaxial cable is connected properly and tightly
- 70 -
- 71 -
- 72 -
SPECIFICATION
High Definition Multimedia Player File Playback Format
Video Audio Picture Subtitle Display MPEG1/2/4, XviD, WMV9, WMV9HD, H.264, HD File(.tp, .trp, .ts), .MKV, .WMV, AVI, .ISO, .IFO, .VOB, .MPG, .ASF, .DAT MP3, WMV, WMA, Ogg Vorbis, AC3, PCM, DTS JPEG, BMP, PNG, GIF SMI, .SUB, .SRT 2inch TFT-LCD
Output Connection
Video Audio e-SATA Interface USB Network NDAS(Network Storage) HDD / Format HDMI, Component, Composite, S-Video Digital : Optical & Coaxial, Anaglog :Stereo YES 1xUSB 2.0 Target Port, 2xUSB 2.0 Host Port Ethernet(100Base-Tx/10Base-T) & Wireless LAN(IEEE802.11b/g) YES 3.5inch SATA HDD Interface / NTFS, FAT32 Supported
Original DVD supported through USB Host : *As we have CSS license, you can play back original DVD title through USB host port if you connect DVD drive into USB host
Power / Operating
Power Adapter Operating Input : AC100V ~ 240V 50/60Hz 1,5 A Output : DC12V 3.0A Temperature : 0 ~ 40 C Humidity : 10 ~ 70 %
- 73 -