The document provides instructions for configuring and connecting to an iDirect satellite modem. It describes connecting to the modem's console port using HyperTerminal to view network information. It also explains how to launch the iSite management software by entering the modem's IP address, and setting the PC's network settings to access the modem. The document outlines navigating iSite's interface to view modem settings and firmware, and loading configuration files to configure the modem.
The document provides instructions for configuring and connecting to an iDirect satellite modem. It describes connecting to the modem's console port using HyperTerminal to view network information. It also explains how to launch the iSite management software by entering the modem's IP address, and setting the PC's network settings to access the modem. The document outlines navigating iSite's interface to view modem settings and firmware, and loading configuration files to configure the modem.
The document provides instructions for configuring and connecting to an iDirect satellite modem. It describes connecting to the modem's console port using HyperTerminal to view network information. It also explains how to launch the iSite management software by entering the modem's IP address, and setting the PC's network settings to access the modem. The document outlines navigating iSite's interface to view modem settings and firmware, and loading configuration files to configure the modem.
The document provides instructions for configuring and connecting to an iDirect satellite modem. It describes connecting to the modem's console port using HyperTerminal to view network information. It also explains how to launch the iSite management software by entering the modem's IP address, and setting the PC's network settings to access the modem. The document outlines navigating iSite's interface to view modem settings and firmware, and loading configuration files to configure the modem.
Copyright:
Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPT or read online from Scribd
Download as ppt
You are on page 1/ 26
Selamat Datang
di
Kelas Training VSAT & Commissioning
Bintek DEPKES ONLINE
DEPARTEMEN KESEHATAN RI PT. Dwi Dharma Nusantara Proprietary & Confidential Basic Network Description
Satellite Internet
Remote Modem(s) Router Antenna VSAT dgn ODU Remote Site
NMS Server
Hub Chassis NetModem
Protocol Processors Outbound Inbound Hub Chassis Hub NetModem(s), Protocol Processor, Network Management System (NMS), Switch dgn VLAN kemampuan VLAN, Upstream Router and Teleport facility (Hub antenna, RFT, Up and Down converters) Peralatan Hub iDirect
PT. Dwi Dharma Nusantara Proprietary & Confidential
PT. Dwi Dharma Nusantara Proprietary & Confidential
Console Port Connection DB-9 to RJ-45 adapter DB-9 to RJ-45 adapter Pin-Out And straight through cable DB-9 to RJ-45 Adapter Pin-Out RJ-45 Color Code DB-9 1 Blue 8 2 Orange 6 3 Black 2 4 Green N.C. 5 Red 5 6 Yellow 3
Open HyperTerminal session 7
8 Brown White/Gray 4 7
Enter a “Name” and select icon
Select “OK”
PT. Dwi Dharma Nusantara Proprietary & Confidential
HyperTerminal Setup Connect using: COM1
Bits per second: 9600
Data bits:8 Parity:None Stop bits:1 Flow control: None Select “OK”: A HyperTerminal will open NetModem console port: Type “laninfo” and NOTE: NetModem IIs from iDirect inventory will typically be select “Enter”. preloaded with an IP address of 208.248.85.21, with a Subnet The NetModem will Mask of 255.255.255.252. NetModemII+s will be preloaded reply with its’ current IP during production with an IP address of 192.168.2.1 and a address and subnet mask Subnet Mask of 255.255.255.0
PT. Dwi Dharma Nusantara Proprietary & Confidential
Setting up your PC
Go to “Network and Dial-up Connections”
Right Click on “Local
Area Connection” Select “Properties” PT. Dwi Dharma Nusantara Proprietary & Confidential Setting up your PC
Highlight “Internet Protocol (TCP/IP)”
Enter IP Address of NetModem as ‘Default Gateway’
Enter Subnet Mask of NetModem Select “Properties” IP Address of NIC is 1 greater than the NetModem
PT. Dwi Dharma Nusantara Proprietary & Confidential
iSite: Getting Started
Enter IP of NetModem in address field
Run Executable file “iSite.exe”
Note: *.exe file must reside in same Select “OK” folder with *.dll files provided
PT. Dwi Dharma Nusantara Proprietary & Confidential
iSite : Password Access
iSite Password Rules:
New, out of box (inventory)
Password = iDirect (upper case D, remainder all lower case). Enter Password of the iSite Modem In field, previously installed/operational Network operator has ability to assign password to each individual remote and/or hub satellite modem. if iDirect does not work call Network Operator to verify what is captured in NMS. Network operators … assign passwords to remotes after they have been commissioned.
NOTE: Super User (su) password via the console connection
is set to be the same as the “NetManager Password” just entered. Select “OK”
PT. Dwi Dharma Nusantara Proprietary & Confidential
PT. Dwi Dharma Nusantara Proprietary & Confidential
“Firmware” Tab
“Firmware” Tab
Image File Name
Software Version
Build Information
PT. Dwi Dharma Nusantara Proprietary & Confidential
“Routing Table” Tab
“Routing Table” Tab
“Requery” to view table
PT. Dwi Dharma Nusantara Proprietary & Confidential
Menu Bar “File” Options Primary use: To load *.opt file. Select “Load Modem Configuration From Disk”
To initiate Option file
Save Current Configuration to Disk “RESET” NetModem
Highlight appropriate *.opt file.
Then select “OPEN”. Warning: If file cannot be located it may have been accidentally changed to *.txt file NetManager searches for only *.opt files File must be saved to Flash. Select “Save Current Configuration To Modem”
PT. Dwi Dharma Nusantara Proprietary & Confidential
Menu Bar “View” Options
Used to enable or disable whether the
“Toolbar” or “Status Bar” is visible.
Check = Enabled / Active
Technician may “Refresh” active
window also located on “Toolbar”
PT. Dwi Dharma Nusantara Proprietary & Confidential
Menu Bar “Configure” Options 1st option is used to load Application / Image files. Select “Download Modem Images”; also icon located on Toolbar Select correct hardware version of NetModem in use (II or II+) The “Download Command Center” window opens. Choose “Select” to search for appropriate Loader File Highlight appropriate *.ldr file. Then select “OPEN” *.ldr file is simple text file which can be hand edited
PT. Dwi Dharma Nusantara Proprietary & Confidential
Down lo ad C omm and Cente r Image(s) from Loader file Current version of software Download
Compress Erase Status
After making selections (Compress / Download /Erase) Select “Download”
Defragment Reset Close
PT. Dwi Dharma Nusantara Proprietary & Confidential
Download Command Center
Status column will display
status of download
Confirm “Reset” by selecting
“Yes”, then “OK”
After Download is complete select “Reset”
PT. Dwi Dharma Nusantara Proprietary & Confidential
Menu Bar “Configure” Options “LAN Configuration”
2nd option is used to change / verify IP
configuration. Select “LAN Configuration”
LAN Configuration entry may be modified
PT. Dwi Dharma Nusantara Proprietary & Confidential
Menu Bar “Configure” Options “iSite Configuration” 3rd “Configure” option, “NetModem Configuration” are tools for the Technician.
“Look Angle Calculator” enables Technician to get Elevation, Azimuth and Polarization for VSAT.
PT. Dwi Dharma Nusantara Proprietary & Confidential
Menu Bar “Configure NetModem” “Antenna Pointing” Tab
To initiate “Antenna Pointing”
feature select “Begin Antenna Pointing” Dialog box confirms setup Tx Cable connected to DVM Antenna off Satellite by 20* Option file is loaded Confirm with “OK”
PT. Dwi Dharma Nusantara Proprietary & Confidential
Menu Bar “Configure NetModem” “Antenna Pointing” Tab
Green = On Satellite Yellow = Satellite Energy Red = Off Satellite
Graphical representation will scroll
across screen (note scale above) Stops Pointing Process
PT. Dwi Dharma Nusantara Proprietary & Confidential
Menu Bar “Configure” Options “Cross Polarization” Tab Note: Rx cable must be disconnected before performing this procedure
On command from NOC select
“Begin Cross Polarization” Select “Calculate” to At time of commissioning, determine L-Band freq. Satellite provider will give End Cross Polarization an RF Uplink (test) Frequency slot. Enter freq. in field provided. 14220 1170
Select “Send Tx Freq”
to program L-Band to Modem Tx Power may be modified by enabling and adjusting level in .5db increments
PT. Dwi Dharma Nusantara Proprietary & Confidential
iSite Toolbar
“Reset” Tool. To reset Modem “Help” Tool: Shows version of NetManager (only)
Toolbar
“Refresh” Tool: Refreshes active window
“Download Modem Images” Tool.
To get to “Download Command Center”
PT. Dwi Dharma Nusantara Proprietary & Confidential
