Transistor Biasing and Stabilisation
Transistor Biasing and Stabilisation
Transistor Biasing and Stabilisation
Lecture
on
TRANSISTOR BIASING
&
STABILIZATION
By:-
Uttampreet Singh
(Lecturer-Electrical Engg.)
Govt. Polytechnic College, Guru Teg Bahadur Garh
(Moga)
2
Transistor Biasing
The basic function of transistor is amplification. The process of raising the
strength of weak signal without any change in its general shape is
referred as faithful amplification. For faithful amplification it is essential
that:-
1. Emitter-Base junction is forward biased
2. Collector- Base junction is reversed biased
3. Proper zero signal collector current
The proper flow of zero signal collector current and the
maintenance of proper collector emitter voltage during the
passage of signal is called transistor biasing.
3
WHY BIASING?
If the transistor is not biased properly, it would work inefficiently and
produce distortion in output signal.
HOW A TRANSISTOR CAN BE BIASED?
A transistor is biased either with the help of battery or associating a
circuit with the transistor. The later method is more efficient and is
frequently used. The circuit used for transistor biasing is called the
biasing circuit.
4
BIAS STABILITY
Through proper biasing, a desired quiescent operating point of the transistor
amplifier in the active region (linear region) of the characteristics is obtained. It is
desired that once selected the operating point should remain stable. The
maintenance of operating point stable is called Stabilisation.
The selection of a proper quiescent point generally depends on the following
factors:
(a) The amplitude of the signal to be handled by the amplifier and distortion
level in signal
(b) The load to which the amplifier is to work for a corresponding supply
voltage
The operating point of a transistor amplifier shifts mainly with changes in
temperature, since the transistor parameters , I
CO
and V
BE
(where the
symbols carry their usual meaning)are functions of temperature.
5
The DC Operating Point
For a transistor circuit to amplify it must be properly biased with dc
voltages. The dc operating point between saturation and cutoff is
called the Q-point. The goal is to set the Q-point such that that it
does not go into saturation or cutoff when an a ac signal is applied.
6
Requirements of biasing network
Ensuring proper zero signal collector current.
Ensuring VcE not falling below 0.5V for Ge transistor and 1V for Silicon
transistor at any instant.
Ensuring Stabilization of operating point. (zero signal IC and VcE)
7
The Thermal Stability of Operating Point (S
Ico)
Stability Factor S:- The stability factor S, as the change of collector
current with respect to the reverse saturation current, keeping and
VBE constant. This can be written as:
The Thermal Stability Factor : S
Ico
S
Ico
= I
c
I
co
This equation signifies that I
c
Changes S
Ico
times as fast as I
co
Differentiating the equation of Collector Current I
C
= (1+)Ico+ Ib &
rearranging the terms we can write
S
Ico
1+
1- (I
b
/I
C
)
It may be noted that Lower is the value of S
Ico
better is the stability
V
be
,
8
Various Biasing Circuits
Fixed Bias Circuit
Fixed Bias with Emitter Resistor
Collector to Base Bias Circuit
Potential Divider Bias Circuit
9
The Fixed Bias Circuit
15 V
C
E
B
15 V
200 k 1 k
The Thermal Stability Factor : S
Ico
S
Ico
= I
c
I
co
General Equation of S
Ico
Comes out to be
S
Ico
1 +
1- (I
b
/I
C
)
V
be
,
Applying KVL through Base Circuit we can
write, I
b
R
b
+ V
be
= V
cc
Diff w. r. t. I
C
, we get (I
b
/ I
c
) = 0
S
Ico
= (1+) is very large
Indicating high un-stability
I
b
R
b
R
C
R
C
10
Merits:
It is simple to shift the operating point anywhere in the active region by
merely changing the base resistor (RB).
A very small number of components are required.
Demerits:
The collector current does not remain constant with variation in
temperature or power supply voltage. Therefore the operating point is
unstable.
When the transistor is replaced with another one, considerable change in
the value of can be expected. Due to this change the operating point will
shift.
For small-signal transistors (e.g., not power transistors) with relatively high
values of (i.e., between 100 and 200), this configuration will be prone to
thermal runaway. In particular, the stability factor, which is a measure of
the change in collector current with changes in reverse saturation current,
is approximately +1. To ensure absolute stability of the amplifier, a
stability factor of less than 25 is preferred, and so small-signal transistors
have large stability factors.
11
Usage:
Due to the above inherent drawbacks, fixed bias is rarely used in linear
circuits (i.e., those circuits which use the transistor as a current source).
Instead, it is often used in circuits where transistor is used as a switch.
However, one application of fixed bias is to achieve crude automatic gain
control in the transistor by feeding the base resistor from a DC signal
derived from the AC output of a later stage.
12
The fixed bias circuit is modified
by attaching an external resistor
to the emitter. This resistor
introduces negative feedback
that stabilizes the Q-point.
Fixed bias with emitter resistor
13
Merits:
The circuit has the tendency to stabilize operating point against
changes in temperature and -value.
Demerits:
As -value is fixed for a given transistor, this relation can be satisfied
either by keeping RE very large, or making RB very low.
If RE is of large value, high VCC is necessary. This increases cost
as well as precautions necessary while handling.
If RB is low, a separate low voltage supply should be
used in the base circuit. Using two supplies of different
voltages is impractical.
In addition to the above, RE causes ac feedback which reduces the
voltage gain of the amplifier.
Usage:
The feedback also increases the input impedance of the amplifier when
seen from the base, which can be advantageous. Due to the above
disadvantages, this type of biasing circuit is used only with careful
consideration of the trade-offs involved.
14
The Collector to Base Bias Circuit
V
CC
R
C
C
E
B
R
F
I
c
I
b
V
BE
+
-
I
E
This configuration employs negative
feedback to prevent thermal runaway and
stabilize the operating point. In this form of
biasing, the base resistor RF is connected to
the collector instead of connecting it to the
DC source Vcc. So any thermal runaway will
induce a voltage drop across the Rc resistor
that will throttle the transistor's base current.
15
Applying KVL through base circuit
we can write (I
b
+ I
C
) R
C
+ I
b
R
f
+ V
be
= V
cc
Diff. w. r. t. I
C
we get
(I
b
/ I
c
) = - R
C
/ (R
f
+ R
C
)
Therefore, S
Ico
(1+ )
1+ [R
C
/(R
C
+ R
f
)]
Which is less than (1+), signifying better thermal stability
16
Merits:
Circuit stabilizes the operating point against variations in temperature
and (i.e. replacement of transistor)
Demerits:
As -value is fixed (and generally unknown) for a given transistor, this
relation can be satisfied either by keeping Rc fairly large or making Rf very
low.
If Rc is large, a high Vcc is necessary, which increases
cost as well as
precautions necessary while handling.
If Rf is low, the reverse bias of the collectorbase region is
small, which limits the range of collector voltage swing that
leaves the transistor in active mode.
The resistor Rf causes an AC feedback, reducing the voltage
gain of the amplifier. This undesirable effect is a trade-off for
greater Q-point stability.
Usage: The feedback also decreases the input impedance of the amplifier
as seen from the base, which can be advantageous. Due to the gain
reduction from feedback, this biasing form is used only when the trade-off
for stability is warranted.
17
This is the most commonly used arrangement for biasing as it provide good
bias stability. In this arrangement the emitter resistance RE provides
stabilization. The resistance RE cause a voltage drop in a direction so as to
reverse bias the emitter junction. Since the emitter-base junction is to be
forward biased, the base voltage is obtained from R1-R2 network. The net
forward bias across the emitter base junction is equal to VB- dc voltage drop
across RE. The base voltage is set by Vcc and R1 and R2. The dc bias
circuit is independent of transistor current gain. In case of amplifier, to avoid
the loss of ac signal, a capacitor of large capacitance is connected across
RE. The capacitor offers a very small reactance to ac signal and so it passes
through the condensor.
The Potential Divider Bias Circuit
18
V
CC
R
C
C
E
B
V
CC
R
1
R
E
R
2
I
E
I
C
I
b
The Potential Divider Bias Circuit
To find the stability of this circuit we have
to convert this circuit into its Thevenins
Equivalent circuit
R
th
=
R
1
*R
2
&
V
th
=
Vcc R
2
R
1
+R
2
R
1
+R
2
V
CC
R
C
C
E
B
V
CC
R
1
R
E
R
2
R
th
=
R
1
*R
2
&
V
th
=
Vcc R
2
R
1
+R
2
R
1
+R
2
R
th
=
R
1
*R
2
&
V
th
=
Vcc R
2
R
1
+R
2
R
1
+R
2
R
th
=
R
1
*R
2
&
V
th
=
Vcc R
2
R
1
+R
2
R
1
+R
2
19
Applying KVL through input base circuit
we can write I
b
R
Th
+ I
E
R
E
+ V
be
= V
Th
Therefore, I
b
R
Th
+ (I
C
+ I
b
) R
E
+ V
BE
= V
Th
Diff. w. r. t. I
C
& rearranging we get
(I
b
/ I
c
) = - R
E
/ (R
Th
+ R
E
)
Therefore,
This shows that S
Ico
is inversely proportional to R
E
and It is less than (1+), signifying better thermal
stability
Thevenin
Equivalent Ckt
(
+
+
+
=
Th R R
R
E
E
Ico S
|
|
1
1
The Potential Divider Bias Circuit
V
CC
R
C
C
E
B
R
E
R
Th
V
Th _
+
Thevenin
Equivalent Voltage
Self-bias Resistor
IE
I
b
I
C
20
Merits:
Operating point is almost independent of variation.
Operating point stabilized against shift in temperature.
Demerits:
As -value is fixed for a given transistor, this relation can be satisfied either
by keeping RE fairly large, or making R1||R2 very low.
If RE is of large value, high VCC is necessary. This increases
cost as well
as precautions necessary while handling.
If R1 || R2 is low, either R1 is low, or R2 is low, or both are
low. A low R1 raises VB closer to VC, reducing the available
swing in collector voltage, and limiting how large RC can be
made without driving the transistor out of active mode. A low
R2 lowers Vbe, reducing the allowed collector current.
Lowering both resistor values draws more current from the
power supply and lowers the input resistance of the amplifier
as seen from the base.
AC as well as DC feedback is caused by RE, which reduces
the AC voltage gain of the amplifier. A method to avoid AC
feedback while retaining DC feedback is discussed below.
Usage:
The circuit's stability and merits as above make it widely used for linear
circuits.
21
Summary
The Q-point is the best point for operation of a
transistor for a given collector current.
The purpose of biasing is to establish a stable
operating point (Q-point).
The linear region of a transistor is the region of
operation within saturation and cutoff.
Out of all the biasing circuits, potential divider
bias circuit provides highest stability to operating
point.
22
THANK YOU