Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Theodolite

Download as ppt, pdf, or txt
Download as ppt, pdf, or txt
You are on page 1of 32
At a glance
Powered by AI
The key takeaways are that a theodolite is an instrument used to measure horizontal and vertical angles precisely, and there are different types of theodolites including vernier, optic and electronic theodolites.

The main components of a theodolite are the levelling head, lower and upper plates, clamps and tangent screws, plate level, telescope, vertical circle and associated parts.

Horizontal angles are measured using the lower plate graduations and verniers on the upper plate. Vertical angles can be measured using the vertical circle. The telescope is used to sight targets and take readings.

THEODOLITE: INTRODUCTION

INTRODUCTION
Theodolite is used to measure the horizontal and
vertical angles.

Theodolite is more precise than magnetic compass.

Magnetic compass measures the angle up to as
accuracy of 30. However a vernier theodolite
measures the angles up to and accuracy of 10, 20.

There are variety of theodolite vernier, optic,
electronic etc.
TYPE OF THEODOLITE
VERNIER THEODOLITE
Vernier theodolite is
also known and transit.

A transit theodolite is
one in which the
telescope can be
rotated in a vertical
plane.



Alidade assembly
Horizontal circle
assembly
Levelling head assembly
Line of Sight
Traverse/horizontal axis
Vertical circle rigidly fixed to
the telescope
Vertical axis
Three assemblies of Theodolite
Main parts of a theodolite
Levelling head (7): Levelling head
is used to attach the instrument to
tripod and attach the plumb bob
along the vertical axis of the
instrument.

MAIN PARTS-2
Lower plate/circle plate (18): an annular
horizontal plate with the graduations provided
all around, from 0 to 360, in a clockwise
direction. The graduations are in degree
divided in to 3 parts so that each division
equals to 20 min.

Horizontal angles are measured with this plate.

The size of the theodolite is defined by the
diameter of horizontal circle.

Upper plate (17): Horizontal plate of smaller
diameter provided with two verniers. on
diametrically opposite parts of its
circumference. These verniers are designated
as A and B. They are used to read fractions of
the horizontal circle plate graduations. The
verniers are graduated in 20 min and each
minute is divided in 3 to 5 parts making least
count 20 or 10.

MAIN PARTS-3
Clamps and tangent screws (15, 19):
There are two clamps and associated tangent
screws with the plate. These screws facilitate
the motion of the instruments in horizontal
plane.

Lower clamp screw locks or releases the
lower plate. When this screw is unlocked both
upper and lower plates move together. The
associated lower tangent screw allows small
motion of the plate in locked position.

The upper clamp screw locks or releases the
upper vernier plate. When this clamp is
released the lower plate does not move but
the upper vernier plate moves with the
instrument. This causes the change in the
reading. The upper tangent screw allows the
fine adjustment.
MAIN PARTS-4
Plate level (5):
Spirit level with the bubble and
graduation on glass cover.
A single level or two levels fixed in
perpendicular direction may be provided.
The spirit level can be adjusted with the
foot screw (21) of the levelling head (7).

Telescope (10): The essential parts of the
telescopes are eye-piece, diaphragm with
cross hairs, object lens and arrangements to
focus the telescope.

MAIN PARTS-5
Vertical circle (1): circular plate
supported on horizontal axis of the
instrument between the A-frames.
Vertical circle has graduation 0-90 in
four quadrants. Vertical circle moves
with the telescope when it is rotated in
the vertical plane.

Vertical circle clamp and tangent
screw (11): Clamping the vertical circle
restrict the movement of telescope in
vertical plane.

Altitude level (2): A highly sensitive
bubble is used for levelling particularly
when taking the vertical angle
observations.

Reading a
theodolite
Vernier scale graduation
Important Definition
Changing face
Revolving the telescope by 180 in vertical plane
about horizontal axis
Again revolving the telescope in horizontal plane
about vertical axis.
Adjustment of the theodolite
Temporary Adjustment




Setting up the theodolite

Measurement of horizontal angle
Measurement of Angle ABC
The instrument is set over B.
The lower clamp is kept fixed and upper clamp is
loosened.
Turn the telescope clockwise set vernier A to 0 and
vernier B to approximately 180.
Upper clamp is tightened and using the upper tangent
screw the vernier A and B are exactly set to 0 and 180.
Upper clamp is tightly fixed, lower one is loosened and
telescope is directed towards A and bisect the ranging rod
at A.
Tightened the lower clamp and turn the lower tangent
screw to perfectly bisect ranging rod at A.
Loose the upper clamp and turn the telescope clockwise to
bisect the ranging rod at C tightened the upper clamp and
do the fine adjustment with upper tangent screw.
The reading on vernier A and B are noted. Vernier A gives
the angle directly and vernier B gives the reading by
subtracting the initial reading (180) from final reading

Read these two method
Repetition method
Reiteration method
Vertical angle measurement-1
Vertical angle measurement-2
Measurements of
Deflection angle
magnetic bearing
A
B
C
P
A
B
N


Read assignment (N. N. Basak, S. K. Duggal)
Ranging and extending a line

Method of traversing
Included angle method
Deflection angle method
Fast angle (or magnetic bearing method)

Computation of latitude and departure
Latitude of a line is the distances measured parallel
to the north south of the North-South direction
Departure of the line is the distance measured
parallel to the east-west direction

Computing latitude and departure

PROBLEM-1
While making survey through the woods, a surveyor with the hand compass
started from point A and walked a thousand steps in the direction S67W and
reached a point B. then he changed his direction and walked 512 steps in the
direction N10E and reached a point C then again he changed his direction
and walked 15 04 steps in the direction S65E and reached a point D as
shown in Figure Now the surveyor wants to return to the starting point A. In
which direction should he move and how many steps should he take.


Sources of errors in theodolite
Instrumental errors
Non adjustment of plate bubble
Line of collimation not being perpendicular to horizontal
axis
Horizontal axis not being perpendicular to vertical axis
Line of collimation not being parallel to axis of telescope
Eccentricity of inner and outer axes
Graduation not being uniform
Verniers being eccentric
. Personal errors
Natural errors
High temperature causes error due to irregular refraction.
High winds cause vibration in the instrument, and this may lead to
wrong readings on verniers
Closing error



Balancing of traverse
Bowditchs rule:
Total error is distributed in proportion to the lengths of the
traverse legs.


Calculation of traverse area

PROBLEM
Calculate the latitudes, departures and closing error
for the following traverse conducted at allahabad.
Adjust also the traverse using Bowditchs rule.

Line Length WCB
AB 89.31 45 10
BC 219.76 72 05
CD 151.18 161 52
DE 159.10 228 43
EA 232.26 300 42

You might also like