Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
579 views

Week 5 Heat Transfer Lecture

This document provides lecture notes on 1-D steady state heat conduction and heat transfer from fins. It discusses key concepts like thermal resistance, critical radius of insulation, and fin effectiveness. For cylindrical and spherical shells, adding insulation initially increases heat transfer until the outer radius reaches the critical value. Fin effectiveness depends on factors like material conductivity, fin geometry, and convection coefficient. Proper fin length offers a balance between heat transfer and size. Heat sinks are designed surfaces that effectively transfer heat from electronic components.

Uploaded by

Henry Hong
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
579 views

Week 5 Heat Transfer Lecture

This document provides lecture notes on 1-D steady state heat conduction and heat transfer from fins. It discusses key concepts like thermal resistance, critical radius of insulation, and fin effectiveness. For cylindrical and spherical shells, adding insulation initially increases heat transfer until the outer radius reaches the critical value. Fin effectiveness depends on factors like material conductivity, fin geometry, and convection coefficient. Proper fin length offers a balance between heat transfer and size. Heat sinks are designed surfaces that effectively transfer heat from electronic components.

Uploaded by

Henry Hong
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 31

Lecture Notes for CO2 (Part 3)

1-D STEADY STATE HEAT


CONDUCTION
Week 5

Rizalman Mamat
Obed Majeed Ali
Universiti Malaysia Pahang

Course Outcome 2 (CO2)


Students should be able to understand and
evaluate one-dimensional heat flow and in
different geometries
Lesson Outcomes from CO2 (Part 3)
To derive the equation for temperature
distribution in various geometries
Thermal Resistance concept to derive
expression for various geometries
To evaluate the heat transfer using thermal
resistance in various geometries
To evaluate the critical radius of insulation
To evaluate heat transfer from the rectangular fins

CRITICAL RADIUS OF INSULATION


Adding more insulation to a wall or
to the attic results:
a) decrease heat transfer and,
b) increase the thermal resistance
of the wall.
In a cylindrical pipe or a spherical
shell, the additional insulation
results :
a) increase the conduction
resistance but,
b) decreases the convection
resistance because of the surface
for convection become larger .

An insulated cylindrical pipe exposed to


convection from the outer surface and
the thermal resistance network
associated with it.

Cylindrical pipe of outer radius r1 whose outer


surface temperature T1 is maintained constant.

The pipe is covered with an insulator (k and r2).

Convection heat transfer at T and h.

The rate of heat transfer from the insulated


pipe to the surrounding air can be expressed
as

Q&

T1 T
T1 T

Rins Rconv ln r2 / r1
1

2 Lk
h 2 r2 L

The critical radius of insulation


for a cylindrical body:

The critical radius of insulation


for a spherical shell:

The rate of heat transfer from the cylinder increases with the
addition of insulation for r2 < rcr
The variation of heat transfer
rate with the outer radius of the
Reaches maximum, when r2 = rcr
insulation r2 when r1 < rcr.
Decreases when r2 > rcr
Thus, insulating the pipe may actually increase the rate of
heat transfer instead of decreasing it when r2 < rcr.

Problem
A 3 mm diameter and 5 m long electrical wire is tightly wrapped with a 2 mm thick
plastic cover whose thermal conductivity is k = 0.15 W/mC. Electrical
measurements indicate that a current of 10A passes through the wire and there
is a voltage drop of 8V along the wire.
If the insulating wire is exposed to a medium at T = 30C with a heat transfer
coefficient of h = 24 W/m2 C, find the temperature at the interface of the wire and
the plastic cover in steady state operation. Also, determine the effect of doubling
the thickness of the plastic cover on the interface temperature.

Solution

Q W e VI 8 10 80 W

Outer surface Area

A 2r2 L 2 0.0035 5 0.11 m 2

Thermal resistances

Rconv

1
1

0.76 0 C/W
hA2 12 0.11

ln r2 r1
ln 3.5 1.5

0.18 0C/W
2kL
2 0.15 5
Rconv Rplastic 0.76 018 0.94 0 C/W

Rplastic
R total

The interface temperature can be determined

T -T
T - 30
Q 1 80 1
T1 103 0 C
Rtotal
0.94
Critical radius

k 0.15
r

00125 m 12.5 mm
Doubling thickness?cr h
12
r2,new 6 mm, which is less than rcr
8

Thus increasing the heat transfer until the outer radius reaches rcr

Problem
A 5-mm-diameter spherical ball at 50 0C is covered by a 1-mm-thick
plastic insulation (k=0.13 W/m 0C). The ball is exposed to a medium
at 15 0C, with a combined convection and radiation heat transfer
coefficient of 20 W/m20C.
Determine if the plastic insulation on the ball will help or hurt heat
transfer from the ball.

Solution

2k 2 0.13

0.013 m 13 mm
h
20
which is greater than r2

rcr

10

HEAT TRANSFER FROM FINNED SURFACES


Newtons law of cooling: The rate of heat transfer
from a surface to the surrounding medium
When Ts and T are fixed, there are two
ways to increase the rate of heat transfer:
Increase the convection heat transfer
coefficient h. This may require the
installation of a pump or fan or add larger
size of fan. Not adequate.

Increase the surface area As by attaching


to the surface extended surfaces called
fins made of highly conductive materials
such as aluminum.

11

The thin plate fins of a car


radiator greatly increase the
rate of heat transfer to the air.

12

Fin Equation

Volume element of a fin at location x


having a length of x, cross-sectional
area of Ac, and perimeter of p.

13

Fin Equation

where

Volume element of a fin at location x


having a length of x, cross-sectional
area of Ac, and perimeter of p.

and
Temperature
excess
14

The general solution of the


differential equation

Boundary condition at fin base

Boundary conditions at the fin


base and the fin tip.

15

1 Infinitely Long Fin


(Tfin tip = T)
Boundary condition at fin tip

The variation of temperature along the fin

Under steady conditions, heat


transfer from the exposed surfaces
of the fin is equal to heat conduction
to the fin at the base.

The steady rate of heat transfer from the entire fin

16

2 Negligible Heat Loss from the Fin Tip


(Adiabatic fin tip, Qfin tip = 0)
Fins are not likely to be so long that their temperature approaches the
surrounding temperature at the tip. A more realistic assumption is for
heat transfer from the fin tip to be negligible since the surface area of
the fin tip is usually a negligible fraction of the total fin area.

Boundary condition at fin tip

The variation of temperature along the fin

Heat transfer from the entire fin

17

3 Specified Temperature (Tfin,tip = TL)


In this case the temperature at the end of the fin (the fin tip) is
fixed at a specified temperature TL.
This case could be considered as a generalization of the case of
Infinitely Long Fin where the fin tip temperature was fixed at T.

18

4 Convection from Fin Tip


The fin tips, in practice, are exposed to the surroundings, and thus the proper
boundary condition for the fin tip is convection that may also include the effects
of radiation. Consider the case of convection only at the tip. The condition
at the fin tip can be obtained from an energy balance at the fin tip.

19

4 Convection from Fin Tip - cont


Replace the fin length L in the relation for
the insulated tip (slide 49) by a corrected
length defined as

t is the thickness of the rectangular fins.


D is the diameter of the cylindrical fins.

Corrected fin length Lc is defined such


that heat transfer from a fin of length Lc
with insulated tip is equal to heat transfer
from the actual fin of length L with
20
convection at the fin tip.

Fin Efficiency
Zero thermal resistance or infinite
thermal conductivity (Tfin = Tb)

21

mL

22

Efficiency of straight fins of rectangular, triangular, and parabolic profiles.


Triangular and parabolic are more efficient than rectangular, contain less
material and more suitable for applications requiring less weight and less
space

23

24

The fin efficiency decreases with increasing fin length because of


decrease in fin temperature with length.
Fin lengths that cause the fin efficiency to drop below 60 percent
usually cannot be justified economically.
The efficiency of most fins used in practice is above 90 percent.

25

Fin
Effectiveness

Effectiveness
of a fin

The thermal conductivity k of the fin


material should be as high as possible.
Use aluminum, copper, iron.
The ratio of the perimeter to the crosssectional area of the fin p/Ac should be
as high as possible. Use slender or thin
pin fins.
Low convection heat transfer coefficient
h. Place fins on the gas (air) side.

26

Proper Length of a Fin

Because of the gradual temperature drop


along the fin, the region near the fin tip makes
little or no contribution to heat transfer.

mL = 5 an infinitely long fin


mL = 1 offers a good compromise
between heat transfer
performance and the fin size. 27

Heat sinks: Specially


designed finned surfaces
which are commonly used in
the cooling of electronic
equipment, and involve oneof-a-kind complex
geometries.

The heat transfer


performance of heat sinks is
usually expressed in terms of
their thermal resistances R.

A small value of thermal


resistance indicates a small
temperature drop across the
heat sink, and thus a high fin
efficiency.

28

29

30

31

You might also like