LIMITS, FITS & Gauges

LIMITS,FITS & Gauges
Why study Limits & Fits

Exact size is impossible to achieve.
Establish boundaries within which deviation from
perfect form is allowed but still the design intent is
fulfilled.
Enable interchangeability of components during
assembly
Definition of Limits:
The maximum and minimum permissible sizes within which
the actual size of a component lies are called Limits.
Tolerance
It is impossible to make anything to
an exact size, therefore it is essential
to allow a definite tolerance or
permissible variation on every
specified dimension.
Why Tolerances are specified?

Variations in properties of
the material being
machined introduce errors.
The production machines
themselves may have some
inherent inaccuracies.
It is impossible for an
operator to make perfect
settings. While setting up
the tools and work piece on
the machine, some errors
are likely to creep in.
Diameter lies between

40.05 mm & 39.95 mm
Tolerance in the above
example is (40.0539.95) =0.10 mm
Unilateral Tolerance
Tolerances on a dimension
may either be unilateral or
bilateral.
When the two limit
dimensions are only on one
side of the nominal size,
(either above or below) the
tolerances are said to be
unilateral.
For unilateral tolerances, a
case may occur when one of
the limits coincide with the
basic size.
Bilateral Tolerance
When the two limit
dimensions are
above and below
nominal size, (i.e.
on either side of
the nominal size)
the tolerances are
said to be bilateral.
Tolerance Accumulation (or)

Tolerance Build up
Tolerance Accumulation (or)

Tolerance Build up
LIMITS OF SIZE & TOLERANCE

Limits of size
The two extreme permissible sizes of a component between which
the actual size should lie including the maximum and minimum
sizes of the component.
Nominal size
It is the size of the component by which it is referred to as a
matter of convenience.
Basic size
It is the size of a part in relation to which all limits of variation are
determined.
Zero Line
It is the line w.r.t which the positions of tolerance zones are shown.
LIMITS OF SIZE &

TOLERANCE
Deviation
It is the algebraic difference between a limit of size and the corresponding basic
size.
Upper Deviation
It is the algebraic difference between the maximum limit of size and the
corresponding basic size. It is denoted by letters ES for a hole and es for a shaft.
Lower Deviation
It is the algebraic difference between the minimum limit of size and the
corresponding basic size. It is denoted by letters EI for a hole and ei for a shaft.
Fundamental Deviation
It is the deviation, either upper or lower deviation, which is nearest to the zero line
for either a hole or a shaft. It fixes the position of the tolerance zone in relation to
the zero line.
Allowance
It is the intentional difference between the hole dimensions and shaft dimension
for any type of fit.
SYSTEM OF FITS
Fit is an assembly
condition between
Hole & Shaft
Hole
A feature engulfing a
component.
Shaft
A feature being
engulfed by a
component.
Clearance fit
In this type of fit, the
largest permitted
shaft diameter is less
than the smallest
hole diameter so that
the shaft can rotate
or slide according to
the purpose of the
assembly.
Interference Fit
It is defined as the fit
established when a negative
clearance exists between the
sizes of holes and the shaft.
In this type of fit, the minimum
permitted diameter of the shaft
is larger than the maximum
allowable diameter of the hole.
In case of this type of fit, the
members are intended to be
permanently attached.
Ex: Bearing bushes, Keys & key
ways
Transition Fit
In this type of fit, the
diameter of the largest
allowable hole is greater
than the smallest shaft,
but the smallest hole is
smaller than the largest
shaft, such that a small
positive or negative
clearance exists between
the shaft & hole.
Ex: Coupling rings, Spigot
in mating holes, etc.
LIMIT GAUGES
A Go-No GO gauge refers to an inspection tool used to check a
workpiece against its allowed tolerances.
It derives its name from its use: the gauge has two tests; the check
involves the workpiece having to pass one test (Go) and fail the other
(No Go). I
t is an integral part of the quality process that is used in the
manufacturing industry to ensure interchangeability of parts between
processes, or even between different manufacturers.
A Go - No Go gauge is a measuring tool that does not return a size in
the conventional sense, but instead returns a state.
The state is either acceptable (the part is within tolerance and may be
used) or it is unacceptable (and must be rejected).
PLAIN GAUGES
Gauges are inspection tools which serve to
check the dimensions of the manufactured
parts.
Limit gauges ensure the size of the
component lies within the specified limits.
They are non-recording and do not determine
the size of the part. Plain gauges are used for
checking plain (Unthreaded) holes and shafts.
Plug gauges
Progressive plug gauges
Ring gauges

LIMITS, FITS & Gauges

Uploaded by

Copyright:

Available Formats

LIMITS, FITS & Gauges

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LIMITS, FITS & Gauges

Uploaded by

Copyright:

Available Formats

LIMITS,FITS & Gauges

Why study Limits & Fits

Why Tolerances are specified?

Diameter lies between

Tolerance Accumulation (or)

Tolerance Accumulation (or)

LIMITS OF SIZE & TOLERANCE

LIMITS OF SIZE &

Progressive plug gauges

You might also like