Introduction To Manufacturing Technology - Lecture 5

Introduction to Manufacturing
Technology Lecture 5
Instructors:
(1)Shantanu Bhattacharya, ME, IITK, email:
bhattacs@iitk.ac.in
(2)Prof. Arvind Kumar, ME, IITK email:
arvindkr@iitk.ac.in
Review of last lecture

Shaws model of projected grains
and parity of modeled MRR with
experimental MRR.
Theoretical and actual trends of
MRR with Feed Force, Frequency,
Amplitude, Work hardness to tool
hardness ratio, Mean grain
diameter, abrasive concentration
and viscosity.
Numerical estimation of MRR and
Numerical Problem
Determine the percentage change in the
machining time for an USM operation cutting
WC plates when the tool material is changed
from copper to stainless steel.
Numerical Problem
Numerical Problem
Ultrasonic Machining Unit

The main units of an
Ultrasonic Machining unit
are shown in the figure
below. It consists of the
following machine
components:
(1)The acoustic head.
(2)The feeding unit.
(3)The tool.
(4)The abrasive slurry and
pump unit.
(5)The body with work
table.
Acoustic Head
1. The Acoustic heads function is to
produce a vibration in the tool.
2. It consists of a generator for supplying
a high frequency electric current, a
transducer to convert this into a
mechanical motion (in form of a high
frequency vibration).
3. A holder to hold the head.
4. A concentrator to mechanically amplify
the vibration while transmitting it to
the tool.
5. Most transducers work on the
magneto-strictive principle because of
high efficiency, high reliability in the
15-30 KHz range, low supply voltage,
and simple cooling arrangement.
6. Stampings are used to reduce loss as in
transformers. The dimensions are so
chosen that the natural frequency
coincides with the electric supply
frequency.
Acoustic
Head
The main purpose of the concentrator is to increase the amplitude to the level
needed for cutting.
Various types of concentrator are used.
The figure below shows how the amplitude of longitudinal vibration of the
transducer-concentrator assembly is amplified. It should be noted that the
system has to be held to the main body at a nodal point.
Feed Mechanism
The objective of the
feed mechanism is to
apply the working
force during the
machining operation.
An instrument
showing the
movement of the tool
indicates the depth
of machining.
The basic type of
feed mechanisms are
the following:
1.Counterweight type
2.Spring type
3.Pneumatic and
hydraulic type
4.Motor type.
Design consideration for

theTool
The tool is made up of a strong but ductile metal.
Stainless steels and low carbon steels are used for making the tools.
Aluminum and brass tools wear ten and five times faster than steel
tools.
The geometrical features are decided by the process.
The diameter of the circle circumscribed about the tool should not be
more than 1.5-2.0 times the diameter of the end of the concentrator.
The tool should be as short and rigid as possible.
When the tool is made hollow the internal contour should be parallel to
the external one to ensure uniform wear.
The thickness of any wall or projection should be atleast five times the
grain size of the abrasive.
In the hollow tool the wall should not be made thinner than 0.5-0.8 mm.
When designing the tool consideration should be given to the side
clearance which is normally of the order of 0.06-0.36mm, depending on the
grain size of the abrasive.
Abrasive Slurry
The most common abrasives are Boron Carbide (B4C),

Silicon Carbide (SiC), Corrundum (Al2O3), Diamond and
Boron silicarbide.
B4C is the best and most efficient among the rest but it is
expensive.
SiC is used on glass, germanium and most ceramics.
Cutting time with SiC is about 20-40% more than that
with B4C.
Diamond dust is used only for cutting diamond and
rubies.
Water is the most commonly used fluid although other
liquids such as benzene, glycerol and oils are also used.
Summa
ry
Introduction to Abrasive Jet

Machining (AJM)
In AJM, the material removal takes
place due to impingement of the fine
abrasive particles.
The abrasive particles are typically of
0.025mm diameter and the air
discharges at a pressure of several
atmosphere.
Mechanics of AJM
Abrasive particle impinges on the
work surface at a high velocity and
this impact causes a tiny brittle
fracture and the following air or gas
carries away the dislodged small
work piece particle.
Mechanics of AJM
The process is more suitable when the work
material is brittle and fragile.
A model for the material removal rate (MRR) is
available from Sarkar and Pandey, 1980.
The MRR Q = Z d3 v3/2 (/ 12Hw)3/4
Where
Z = No. of abrasive particle impacting per

unit time.
d = Mean diameter of the abrasive grain
v = Velocity of the abrasive grains
= Density of the abrasive material
Hw = Hardness of the work material
= Is a constant.
Process parameters
The process characteristics can be evaluated
by judging (1) the mrr (2) the geometry of the
cut (3) the roughness of the surface produced
(4) the rate of nozzle wear.
The major parameters which control these
quantities are:
1.The abrasive (composition, strength, size and
mass flow rate).
2.The gas (composition, pressure and velocity).
3. The nozzle (geometry, material, distance
from and inclination to the work surface).
The Abrasive
Mainly two types of abrasives are used (1) Aluminum oxide

and (2) Silicon carbide. (Grains with a diameter 10-50
microns are readily avialable)
For good wear action on the surfaces the abrasive grains
should have sharp edges.
A reuse of the abrasive powder is normally not
recommended because of a decrease of cutting capacity
and clogging of the nozzle orifices due to contamination.
The mass flow rate of the abrasive particles depends on the
pressure and the flow rate of the gas.
There is an optimum
mixing ratio (mass fraction
of the abrasive) for which
the metal removal rate is
the highest.
When the mass flow rate of
the abrasive increases the
material removal rate also
increases.
The gas
The AJM unit normally operates at a pressure of 0.2-1.0 N/mm 2 .
The composition of gas and a high velocity has a significant
impact on the MRR even if the mixing ratio is not changed.
The nozzle
The nozzle is one of the most vital elements controlling the
process characteristics.
The nozzle material should be hard to avoid any significant
wear due to the flowing abrasive. [Normally WC (avg. life: 1230 hrs.) or Sapphire (Appr. = 300 hrs.) are used]
For a normal operation the cross-sectional area of the orifice
can be either circular or rectangular and between 0.050.2mm2 .
Nozzle to tip distance (Stand off

distance)
The nozzle tip distance (NTD) or the stand off distance is a

critical parameter in AJM.
The NTD not only affects the MRR from the work surface
but also the shape and size of the cavity produced.
As shown in the figure below, the velocity of the abrasive
particles impinging on the work surface increases due to
their acceleration after they leave the nozzle. This increases
the MRR.
With a further increase in the NTD, the velocity reduces due
to the drag of the atmosphere which initially checks the
increase in MRR and then decreases it.
Photo graphs of the actual Machined Cavity profile

at different NTD
Profile of the machined

cavity at different stand off
distances
(a) 2mm (b) 6mm (c) 10mm
(d) 14mm (e) 16mm (f)
20mm
Mixing and Mass Ratio

Mixing ratio (M) also influences the MRR.
M = Volume flow rate of abrasive particles
Volume flow rate of carrier gas
= a/ g
In place of M the mass ratio may be easy
to determine.
= Ma/ Ma+c =
rate
Abrasive mass flow rate

Abrasive and carrier gas combined mass flow
Numerical Problem
During AJM, the mixing ratio used is
0.2. Calculate mass ratio if the ratio
of density of abrasive and density of
carrier gas is equal to 20.
Numerical Problem
Diameter of the nozzle is 1.0mm and
the jet velocity is 200m/s. Find the
volumetric flow rate (cm3/sec) of the
carrier gas and the abrasive mixture
Abrasive Jet Machines

The abrasive jet
machines are
manufactured by a
single
manufacturer M/s
Airbrasives.
(SS White and
Co., New York)
The gas propulsion system supplied clean and dry gas (air, nitrogen, or CO2) to
propel the abrasive particles.
The gas may be supplied either by a cylinder or a compressor.
In case of a compressor a filter or a dryer may be used to avoid water or oil
contamination to the abrasive powder.
The gas should be non toxic, cheap and easily available and should not
excessively spread when discharged from nozzle into atmosphere.
Electrochemical Machining
(ECM)
Electrochemical machining is one of the most unconventional
machining processes.
The process is actually the reverse of electroplating with some
modifications.
It is based on the principle of electrolysis.
In a metal, electricity is conducted by free electrons but in a
solution the conduction of electricity is achieved through the
movement of ions.
Thus the flow of current through an electrolyte is always
accompanied by the movement of matter.
In the ECM process the work-piece is connected to a positive
electrode and the tool to the negative terminal for metal removal.
The figure below shows a suitable work-piece and a suitably
shaped tool, the gap between the tool and the work being full of a
suitable electrolyte.
Electrochemical
Machining
The dissolution rate is more where the gap is less and vice versa.
This is because the current density is inversely proportional to the gap.
The dissolution rate is more where the gap is less and vice versa (as the current density is
proportional to the gap.
Now, if the tool is given a downward motion, the work surface tends to take the same shape
as that of the tool, and at a steady state the gap is uniform.
Thus the shape of the tool is represented in the job.
In an electrochemical machining process, the tool is provided with a constant feed motion.
The electrolyte is pumped at a high pressure through the tool and the small gap between the
tool and the work-piece.
The electrolyte is so chosen that the anode is dissolved but there is no deposition on the
cathode.
The order of the current and voltage are a few 1000 amps and 8-20 volts. The gap is of
the order of 0.1-0.2mm .
The metal removal rate is typically 1600 mm3/sec for each 1000 Amp.
Approximately 3 KW-hr. are needed to remove 16000 mm3 of metal which is almost 30
times the energy required in a conventional process.
With ECM the rate of metal
removal is independent of
the work-piece hardness.
ECM becomes
advantageous when either
the work material possesses
a very low machinability or
the shape to be machined is
complex.
Unlike most other conventional and unconventional processes, here there is

practically no tool wear.
Though it appears that, since machining is done electrochemically, the tool
experiences no force, the fact is that the tool and work is subjected to large forces
exerted by the high pressure fluid in the gap.
Electrochemistry of ECM
process
The electrolysis process is governed
by the following two laws proposed
by Faraday.
(1)The amount of chemical change produced by an electric current, that

is, the amount of any material dissolved or deposited, is proportional to
the quantity of electricity passed.
(2)The amounts of different substances dissolved or deposited by the
same quantity of electricity are proportional to their chemical equivalent
weights.
In the quantitative form, Faradays two laws state that
mIt
Where, m = weight (in grams) of a material dissolved or deposited,
I = Current (in amperes)
t = time (in seconds)
= gram equivalent weight of the material.
Ion-Ion and ion-solvent

interaction
Although strong electrolytes are completely ionized, their ions

are not entirely free to move independently of one another
through the body of a solution, except when this is infinitely
dilute.
The following things happen in such a situation:
1. Ions will move randomly wrt each other due to fairly violent
thermal motion.
2. Coulombic forces between ions of same and opposite kinds will
be present which leads to a time averaged ion atmosphere of
one kind wrt. To a central ion of the opposite kind.
3. Movement of such ions under an external electric field will be
very slow. So the atmosphere moves to the opposite direction
as the primary central ion resulting in a continouous disruption
and reformation of the atmosphere. (atmosphere
assymetrically distributed around the central ion) and
electrophoretic effect(viscous drag of the atmosphere)

Introduction To Manufacturing Technology - Lecture 5

Uploaded by

Copyright:

Available Formats

Introduction To Manufacturing Technology - Lecture 5

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Introduction To Manufacturing Technology - Lecture 5

Uploaded by

Copyright:

Available Formats

Introduction to Manufacturing

Review of last lecture

Ultrasonic Machining Unit

Design consideration for

The most common abrasives are Boron Carbide (B4C),

Introduction to Abrasive Jet

Z = No. of abrasive particle impacting per

Mainly two types of abrasives are used (1) Aluminum oxide

Nozzle to tip distance (Stand off

The nozzle tip distance (NTD) or the stand off distance is a

Photo graphs of the actual Machined Cavity profile

Profile of the machined

Mixing and Mass Ratio

Abrasive mass flow rate

Abrasive Jet Machines

Unlike most other conventional and unconventional processes, here there is

(1)The amount of chemical change produced by an electric current, that

Ion-Ion and ion-solvent

Although strong electrolytes are completely ionized, their ions

You might also like