THREADS

TRAINING & DEVELOPMENT/OD

SHAHI EXPORTS PVT LTD
 THREADS

What is thread

Calculation, Control & Wastage

Introduction

The smallest failure in thread performance results in losses

on investments in material, equipment, garment
engineering, and labour. Hence, it is important to know
your thread thoroughly. Enhancing thread knowledge,
analysing thread parameters, the right selection procedure
and use of thread plays a major role in achieving good
sewing performance and the desired seam quality.
This Bulletin Post serves an introduction to
the types of threads, the properties, thread
construction, and factors affecting thread
performance.
 What is a sewing thread?

Sewing threads are special kinds of yarns that are

engineered and designed to pass through a sewing
machine rapidly. They form efficient stitches without
breaking or becoming distorted during the useful life
of the product. The basic function of a thread is to
deliver aesthetics and performance in stitches and
seams.
What are the factors that affect
functions of a sewing thread?
Factors affecting Factors affecting performance
aesthetics Thread used in garments must be
durable enough to withstand the
abrasion and needle heat that
Colour, lustre and fineness / occur while sewing, garment
thickness should be finishing, stretching and recovery
considered while selecting a during wear.
thread for decorative Thread performance in garments
purposes such as top can be evaluated from its
stitching or embroidery. Seam strength
Hue and shade matching Abrasion resistance
Colour fastness Elasticity
Chemical resistance
Stitch selection
Flammability
Uniformity of stitch Colour fastness
formation
 What is 'sewability'?
What is 'sewability'?

'Sewability' of thread is a term used to

describe a sewing threads performance. A
thread with good sewability is uniform in
diameter with a good surface finish.
Longitudinal uniformity of thread contributes
to uniform strength and reduced friction, as it
passes through the stitch forming
mechanisms. It also minimises thread
breakages and the associated costs incurred
from rethreading machines, repairing stitches
and producing inferior quality products.
Sewability parameters

No breakages in high-speed sewing

Consistent stitch formation
No skipped stitches
Evenness, to prevent changes in tension
during sewing
A high level of abrasion resistance
Sufficient surface smoothness, to pass
easily through the machine guides
Thread classification
Thread can be classified in different ways.
Some common classifications are those
based on:

Substrate

Construction

Finish
Classification based on substrate

Natural
The usage of thread made from natural substrates is
now minimal in industry applications. However, the
most commonly used natural thread is cotton thread.

Synthetic
Due to the limitations of natural fibres, thread users
have turned to threads made from synthetic fibres as
they have desirable properties of exceptionally high
tenacity, high resistance to abrasion and good
resistance to chemicals. They are also not significantly
affected by moisture, rot, mildew, insects or bacteria.
Classification based on construction thread structure

Spun threadis made using natural or synthetic

fibres. Spun polyester is one of the most widely
used threads. It is stronger than cotton threads of
a comparable size, and is available in a wide
variety of sizes and colours.
Classification based on construction thread structure

Corespun threadis a combination of staple fibres and

filaments. The most commonly used corespun thread has
multiple-ply construction, with each ply consisting of a
polyester filament core with cotton or polyester fibres
wrapped around the core.

This thread structure influences the strength of filament

polyester and the sewability of cotton or polyester fibre
wrap. Corespun thread is generally used for the high-speed
sewing of many garment types, especially those requiring
high seam strength.
Filament threads

Filament threadsare stronger than

spun threads of the same fibre and
size. Three types of filament threads
are commonly used:
Mono Filament Thread
Smooth Multifilament Thread
Textured Filament Thread
Monofilament thread
Monofilament threadis made from a single
continuous fibre with a specified thickness.
Though monofilament is strong, uniform and
inexpensive to make, it lacks flexibility and is stiff
and scratchy in feel. As a result, usage is
normally restricted to hems, draperies, and
upholstered furniture.
Smooth multifilament
thread
Smooth multifilament threadis usually made
from nylon or polyester and is used where high
strength is a primary requirement. It consists of
two or more continuous filaments twisted
together. It is commonly used to sew shoes,
leather garments, and industrial products.
Textured filament thread
Textured filament threadis usually made from
polyester and is used primarily as the looper
thread for cover stitches. Texturing filaments
gives the yarn more cover and high extensibility,
but makes the thread more subject to snagging.
Basics of thread construction

All conventional sewing threads begin their production cycle as

simple yarns. These basic yarns are produced by twisting
together relatively short fibres or fine continuous filaments.
Some terms used in the context of thread construction are:
Twist Twist is simply the number of turns per unit length. A
thread with too little twist may fray and break, one with too much
twist can cause snarling, looping and knotting. Balance is the key
and a good sewing thread has it.
Twist direction The direction of the finishing twist is important,
twist can be inserted in either direction and this is described as
either Z or S twist. Most common machines use a Z twist thread.
There are other descriptions of twist which were used in the past
but these should not be used to avoid confusion.
Direction of twist does not affect the strength of the thread, but it
can seriously impair its performance when it is used on a
machine for which it is not suited.
Z & S
TWIST
Ply and cord
Ply and cord Yarns with many components are
twisted together to form ply thread. Most
commonly used are 2, 3 or 4 ply threads. Threads
are twisted together to give corded thread. Most
commonly used are 4, 6 or 9 cord threads.
SIZE
Size The overall thickness of the final thread is
referred to as Grist, Ticket Number, Tex or
Count. Thread should be as fine as possible
depending on the required strength of seam.
Generally, thicker threads have greater strength,
given the same fibre content and yarn structure.
Finer threads tend to blend into the fabric surface
and are less subject to abrasion than seams with
heavier threads. Finer threads perform better with
finer needles and produce less fabric distortion
than heavier needles

Classification based on thread finish

Finishes are given to a thread for two purposes

1.To improve sewability
Some finishes involve increasing strength,
abrasion resistance and lubrication of the
thread.
2.To achieve a specific functional
requirement
Some finishes include bonding, non wick, anti-
fungal, fire retardant, water repellent and anti-
static finishes.
Thread terminology

With a wide selection of threads to choose from, it is important to know

some of the terminology associated with significant thread properties to
judge the differences between different thread types.
Tensile strengthis the tension at which a thread breaks, expressed in
grams or kilograms (force).
Tenacityis the relative strength obtained by dividing the tensile
strength by the thickness of the structure.
Loop strengthis the load required to break a length of thread which is
looped through another length of the same thread.
Minimum loop strengthis the strength of the weakest loop in a series
of loops (tested in a continuous length of thread).
Elongation at breakis the amount by which a thread is extended at
its breaking point expressed as a percentage of its original length.
Modulusis a term used to denote a numerical value which indicates
the manner in which the textile behaves when a tensile force is applied.
Elasticityis a property of the thread which enables it to recover to its
original length after being extended by a set amount.
Shrinkageis the amount by which a thread contracts under the action
of washing or heating.
Moisture regainis the weight of moisture in a fibre or thread
expressed as a percentage of weight of completely dry material.
Requirements of good quality sewing thread

Good tensile strengthholds the stitched seam

securely during wash and wear.
Smooth surface and absence of faultsensures less
friction between the needle and the material during
high-speed sewing. The thread must be well lubricated
to increase its sewability and resistance to abrasion.
Uniform thickness / diameterresults in an even
sewing thread, which moves smoothly and quickly
through the needle eye and the fabric. It also affects
the threads tensile strength, resistance to abrasion
and its twist construction. An uneven thread may twist
into short knots and jam at the eye of the needle.
Requirements of good quality sewing thread

Good elasticityenables thread to recover its original

length immediately after the tension has been released.
The elasticity of sewing thread affects the strength and
the finished quality of a stitched seam.
Good colour fastnessprovides immunity to the different
agents the thread is exposed to during manufacture and
washing. The thread must hence be uniformly dyed.
Low shrinkageof the thread being used on the fabric
material with higher shrinkage reduces the chances of
seam puckering.
Good resistanceto chemical attackis a desirable
property for thread used in garments which may undergo
washing, bleaching or dry-cleaning.
Requirements of good quality sewing thread

Good abrasion resistanceensures a good sewing

performance and makes the thread more durable.
The following figures show the results of thread-to-thread
abrasion tests and give an indication of their respective
resistance to abrasion:
If Linen, Rayon Continuous Filament (CF) has resistance of
1, then:
Cotton = 3
Spun Silk = 4
Spun Polyester = 12
CF Polyester = 30
Spun Nylon = 40
CF Nylon = 150
Requirements of good quality sewing thread

Good colour fastnesswill retain the threads original colour without

running or fading when subjected to wash and light exposure. The thread
colour should be resistant to different agents to which it is exposed
during manufacture and use.
Colour fastness can be measured against:
Chlorinated water
Perspiration
Cold water staining
Dry cleaning
Pressing - wet and dry
Bleaching
Minimal metamerismcan be achieved by assessing colour with colour
matching cabinets. Metamerism is an inherent property of a thread when
the same thread colour appears to be different under different lighting
conditions. Standard illuminants are often used to counter the effects of
metamerism.
Thread Multiplying Factor
Machine type Multiplying Factor in Mtr
SNLS 2.72
DNLS 5.44
3TH O/L 14
4TH O/L 18
5TH O/L 20
6TH O/L 24
BABY O/L 14
BLANKET STITCH 3 THREAD 25
ZIG ZAG 3 THREAD 12
PUCKERING 5.5
PICOTING 2THREAD 15
PICOTING 3THREAD 20
PICOTING 6THREAD 40
BLIND HEM 5
Thread Multiplying Factor
Machine type Multiplying Factor in Mtr
SNCS 6
DNCS 11
BUTTONHOLE 1
BUTTON ATTACH 0.5
KEYHOLE 3
SMOCKING 5.5(1.5CM NDLS & 4CM LOOPER)
PICK STITCH 6
FACOTTING 10
FLATLOCK 3THREAD NDL GZ 2/8 14(10MTR THIN & 4MTR THICK)
FLATLOCK 3THREAD NDL GZ 1/8 11(7MTR THIN & 4MTR THICK)
FLATLOCK 5THREAD NDL GZ 2/8 27(15MTR THIN & 12MTR THICK)
FLATLOCK 4THREAD NDL GZ 2/8 23(11MTR THIN & 12MTR THICK)

FLATLOCK 4THREAD NDL GZ 1/8 15(7MTR THIN & 8MTR THICK)

PICO 3.6
How to calculate the thread of Seam
Take a measurement tape.
Place the measurement tape on the seam to
be measured and see the measurement in
centimeters.
Add extra wastage of 3centimeters on both
sides of seam means 6centimeters in total
seam length.
Now see on which machine this seam has been
performed.
Check the multiplying factor of that machine.
Multiply the total seam length with the
multiplying factor & add the wastage of 10%
into it.
Example
Seam length - 25cm + 6cm =
31cm
Machine - DNLS
Multiplying factor - 5.44
= (31 x 5.44) + 10%
=168.64 + 16.86
=185.50cm
 How to control Thread
Wastage
While sewing the garment the thread has to be cut from
the root of the garment seam which has been performed.
Within the line the sewing thread cones will be given
after getting back the unfilled cones.
After the completion of style the thread cones will be
returned back to stores in a proper way to analyze the
leftover of thread.
Housekeeping department will be trained related to the
valuable items (bobbin, bobbin case, thread cones &
labels) of shop floor.
Operators need to be trained related to the value of
threads & other valuable items.
Incase of small order qty rewinding of cones need to be
taken in practice.