Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
117 views

Arduino

Arduino is an open source electronic prototyping platform that allows users to create interactive electronic objects and prototypes that can sense and control the physical world. It contains programs called sketches that can be uploaded to the board to run. The setup function runs once on startup and loop runs continuously to do the main work. Pins on the Arduino board can be configured as either inputs or outputs using pinMode and their states can be set using digitalWrite. Analog signals are continuous voltages that must be converted to digital for the microcontroller using an analog to digital converter.

Uploaded by

wmarasigan2610
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
117 views

Arduino

Arduino is an open source electronic prototyping platform that allows users to create interactive electronic objects and prototypes that can sense and control the physical world. It contains programs called sketches that can be uploaded to the board to run. The setup function runs once on startup and loop runs continuously to do the main work. Pins on the Arduino board can be configured as either inputs or outputs using pinMode and their states can be set using digitalWrite. Analog signals are continuous voltages that must be converted to digital for the microcontroller using an analog to digital converter.

Uploaded by

wmarasigan2610
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 14

Wilson Marasigan

 Open Source electronic prototyping platform


based on flexible easy to use hardware and
software. <https://www.arduino.cc/>
 Robotics
 Remote Controller
 Automation
 OLE
 IOT
 Prototype
 Game Controller
void setup() {
// put your setup code here, to run once:
}

void loop() {
// put your main code here, to run
repeatedly:
}
 setup : It is called only when the Arduino is
powered on or reset. It is used to initialize
variables and pin modes

 loop : The loop functions runs continuously


till the device is powered off. The main logic
of the code goes here. Similar to while (1) for
micro-controller programming.
 A pin on arduino can be set as input or
output by using pinMode function.

 pinMode(13, OUTPUT); // sets pin 13 as


output pin

 pinMode(13, INPUT); // sets pin 13 as input


pin
 digitalWrite(13, LOW); // Makes the output
voltage on pin 13 , 0V

 digitalWrite(13, HIGH); // Makes the output


voltage on pin 13 , 5V

 int buttonState = digitalRead(2); // reads the


value of pin 2 in buttonState
 What is analog ?
 It is continuous range of voltage values (not
just 0 or 5V)

 Why convert to digital ?


 Because our microcontroller only understands
digital.
 The Arduino Uno board contains 6 pins for
ADC

 10-bit analog to digital converter

 This means that it will map input voltages


between 0 and 5 volts into integer values
between 0 and 1023
 analogRead(A0); // used to read the analog
value from the pin A0

 analogWrite(2,128);
 // These constants won't change. They're used to give names to the pins used:
const int analogInPin = A0; // Analog input pin that the potentiometer is attached to
const int analogOutPin = 9; // Analog output pin that the LED is attached to
int sensorValue = 0; // value read from the pot
int outputValue = 0; // value output to the PWM (analog out)
void setup() {
// initialize serial communications at 9600 bps:
Serial.begin(9600);
}
void loop() {
// read the analog in value:
sensorValue = analogRead(analogInPin);
// map it to the range of the analog out:
outputValue = map(sensorValue, 0, 1023, 0, 255);
// change the analog out value:
analogWrite(analogOutPin, outputValue);
// print the results to the serial monitor:
Serial.print("sensor = " );
Serial.print(sensorValue);
Serial.print("\t output = ");
Serial.println(outputValue);
// wait 2 milliseconds before the next loop
// for the analog-to-digital converter to settle
// after the last reading:
delay(2);
}

You might also like