Boiler Mountings

Boiler Mountings
Regular accidents and boiler break down can happen due to improper maintenance and cleaning. Without boiler mounting
one can damage boiler and its surrounding with one mistake followed by a series of events. Without high lift safety valve
the shell could explode resulting into great loss of life and machinery; similarly a shell could collapse under vacuum if air
vent is not present during cooling down. During cargo operation there is a increased demand for steam and so the
mountings help operate the boiler with more and ease and safety. Boiler mountings include:
1 ) Safety Valves
Safety valves are fitted on every boiler to avoid over pressurizing. Normally three safety valves are fitted on the boiler
with one on the super heater and rest two on steam drum. In no condition these valves be less than two in number and
must lift at a pressure 3% above boiler working pressure irrespective of boiler types.
A steam valve is made up of cast iron body with two independent valves fitted on the valve seat. These valves are
connected to a lever by means of a pivot held tight to its position by spring. The spring force keep the valve sit shut on
the valve seat under normal condition. When the upward pressure exceeds the downward spring force; the valve is lifted
and excess steam is released to the atmosphere.
Safety Valves
2 ) Steam Stop valve
A steam stop valve is connected to the boiler to stop and regulate steam flow from boiler
to the distribution lines. Main steam stop valve on boiler is kept shut to avoid back-flow
of steam to the boiler. The flange of the steam stop valve is bolted on top of the steam
drum. Valve main body is made of cast iron while the valve seat is made from gun metal.
The spindle on one end is connected to the valve while the other end to the handle
wheel passing through ( yoke / Gland nut ) and gland packing. The valve is operated by
rotating the hand wheel. Rotating hand wheel in turn rotate the spindle which move the
valve up allowing path for steam to flow.
3 ) Man Hole
Manholes are the access door provided in the boiler outer casing or in the shell of a
closed pressure vessel for human and material entry into the otherwise closed (confined)
space.
4) Pressure gauge
Pressure gauge are fitted to the steam drum and super heater to indicate steam pressure inside. These
gauge are fitted on the front top of the boiler shell and represent pressure in bar. A bourdon tube of
closed cross section is attached to the steam space on one end through siphon tube. The tube itself
contain water to avoid steam to enter into the pressure gauge. The pointer is connected to the threaded
gear attached to the spindle. When pressure is applied to the bourdon tube it becomes circular turning
the spindle. This cause the pointer to move along with the gear; representing the boiler pressure.
Pressure gauge Water Level Indicator
5 ) Water Level Indicator
A pair of water level indicator is installed directly to the boiler shell with an additional remote reading gauge installed at
convenient position. They are installed directly on the front end of all boiler types; showing water level in boiler drum. It
consist of a glass tube with three independent cock ( Steam cock, water cock and drain cock ).
Steam and water cock separates the glass tube with boiler steam and water respectively. Drain cock on other hand used to
drain water from glass tube. A metal ball is provided on the water side of the gauge glass to avoid subsequent accident and
water loss; by water flashing off steam in event of glass rapture / failure.
Under normal condition both steam and water cock is open allowing water and steam pressure to balance. In event of
incorrect reading we need to blow through; by closing the water cock and opening drain cock. A strong blow will indicate
the steam cock is clear; now repeat the process with steam cock closed and water cock opened. Strong blow of steam with
hissing sound indicate the water cock is clear. Now close the drain cock and let water fill in; slowly open the steam cock
equalizing the pressure.
6 ) Feed Check Valve

A feed check valve is a non return valve type fitted on the boiler shell just below the normal water level. It regulates the
flow of feed water restricting possible back flow to the feed pump. These valves are usually fitted with extended spindle
for remote operation. The inlet and outlet point of these valves are exposed to different pressure. When the feed pump is
operational; sufficient pressure is build at the inlet point of the valve. When the inlet pressure is more than the outlet
point the valve lift allowing water to pass to the boiler.
7 ) Fusible Plug
A fusible plug is the threaded gunmetal cylinder with conical plug and tappet
hole drilled into it. This This hole is then filled with an alloy of low melting
point such as tin. The plug can be of either fire actuated or steam actuated
type fitted over the combustion chamber.
Feed Check Valve

8) Mudhole
A small manhole, too small for access but useful for washing out the boiler, either as
an inlet for a hose or as a drain for removed mud. See also washout plug
9) Blow-down cock
A valve mounted low-down on the boiler, often around the foundation ring, which is used for blow down.

Boiler Mountings

Uploaded by

Copyright:

Available Formats

Boiler Mountings

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Boiler Mountings

Uploaded by

Copyright:

Available Formats

Boiler Mountings

6 ) Feed Check Valve

Feed Check Valve

You might also like