LED TV

Training manual
UE8Y
 index
I. Overview

II. Inside of UE8Y

III. Inside of UE8Y

IV. New Function of UE8Y

V. Disassembly and Reassembly

VI. Troubleshooting
UE8Y Overview

SAMSUNG
UE8Y Overview
Spec Comparison to the Old Models
Model E8000 D8000

Design

Display type LED TV LED TV

LCD panel TFT LCD PANEL 240Hz TFT LCD PANEL 240Hz

40.99 x10.89 x26.75 inches_with stand 42.94x11.93x28.50 inches_with stand

46”
40.99 x 1.17 x 23.6 inches_without stand 42.94x0.94x26.09 inches_without stand
Dimensions
(W x H x D) 48.53 x 12.18 x 30.99 inches_with stand
50.47x11.93x32.78 inches_with stand
55” 48.53 x 1.17 x 27.84 inches_without stand
50.47x0.94x30.39 inches_without stand

46” : 27.34lbs_without stand 46” : 37.03lbs_without stand

31.52lbs_with stand 42.1lbs_with stand
Weight
55” : 35.71lbs_without stand 55” : 48.94lbs_without stand
41bs_with stand 54.01lbs_with stand

Contrast Ratio Mega CR Mega CR

AUTO MOTION PLUS 240HZ O (Echo-S) O (Napoli)

Speaker out 10W +10W 46” : 10W +10W/ 55” :15W+15W

Surround Sound SRS Theater Sound SRS Theater Sound

3D,MOIP,Media Bridge, AllShare,Internet TV,

3D,MOIP,Media Bridge, AllShare,Internet
Function Built-in WiFi, Full Browser,Bluetooth,
TV, Built-in WiFi, Bluetooth
Smart_control, Motion Contol
UE8Y Overview

UE8E Key parts

- 1080P FULL HD
- 3HDMI, HDMI CEC support
- 240Hz Auto Motion Plus
- Media Play
- All Share
- Smart Hub
- Full browser
- Built–in Wifi
-Motion Control & Voice Contol
-Smart Control

UE8E

- Vesel: Super Narrow Bezel (Factory Option: W-milky)

- Panel:46”,55”, Super Clear
- memory: 2G (internet TV & ACAP service)
- power consumtion: 46”: 150W / 55”:170W/Standby <0.1W
UE8Y Overview
Control & Connection Panel
UE8Y Overview
Rear View UE8000 46”
UE8Y Overview
Rear View UE8000 55”
UE8Y Overview
Remote controller
UE8Y Overview
Remote controller
UE8Y Overview
Accessories
UE8Y Overview
Accessories
Inside of UE8Y

Inside of UE8Y

SAMSUNG
Inside of UE8Y
Inner Feature of UE8Y
IP board, Main board, Panel

MoiP Cable MoiP(IR)

Power Board

Main board
LVDS Cable

T-CON

Speaker(L)
Speaker(R)
Inside of UE8Y
Wiring Diagram of UE8Y

CNM803

CN8015

CON3
Main Board
SAMSUNG
Explanation of Main board
Main board LAYOUT
Model 46”/55”

USB3

USB2 Moip
Please show bottom
of board (move
OPTICAL
photo up or make
USB3 smaller)
IC1202 CN201
IC Video Power
process
HDMI1

IC801
HDMI2 IC Video
decoder CN1601
LVDS

HDMI3

CN1201
Function
Component

CN301
AV IN2 Speaker

AUDIO
L/R
LAN
AV IN1
Ex-Link RF

FRONT BACK
Explanation of Main board
Pin Map
21
20
18

1
17

16

15
2

14

19
13
3

12

4
11

10
5

8 7

6
Explanation of Main board
Pin Map
1. CN401(MOIP_IR_ECO SENSEOR) 3. CN1602(LVDS)
1 NC 27 LVDS_EVEN_TX0-
1 NC 12 A3.3V_PW
2 DGND 28 DGND
2 NC 13 DSCL_3.3V 3 SDA_3D_FRC 29 LVDS_ODD_TX4+
3 NC 14 DSDA_3.3V 4 PWM_DIMMING_TCON1 30 LVDS_ODD_TX4-
5 SCL_3D_FRC 31 LVDS_ODD_TX3+
4 NC 15 DGND
6 PWM_DIMMING_TCON3 32 LVDS_ODD_TX3-
5 NC 16 A3.3V_PW 7 PWM_DIMMING_TCON2 33 DGND
6 KITE I2STX DATA 17 IR 8 SDA_PANEL 34 TLVDS_ODD_TXCLK+
9 PANEL_I2C_SW 35 LVDS_ODD_TXCLK-
7 KITE I2STX LRCLK 18 A5V_MOIP_PW 10 EMITTER_BT_SYNC_OUT 36 DGND
8 KITE I2STX BCLK 19 DGND 11 REF_SYNC_IN 37 LVDS_ODD_TX2+
12 SCL_PANEL 38 LVDS_ODD_TX2-
9 DGND 20 USB_MOIP_DP
13 DGND 39 LVDS_ODD_TX1+
10 AIT_RESET 21 DGND 14 LVDS_EVEN_TX4+ 40 LVDS_ODD_TX1-
11 WOV 22 USB_MOIP_DM 15 LVDS_EVEN_TX4- 41 LVDS_ODD_TX0+
16 LVDS_EVEN_TX3+ 42 LVDS_ODD_TX0-
17 LVDS_EVEN_TX3- 43 DGND
2. CN201(POWER) 18 DGND 44 DGND
19 LVDS_EVEN_TXCLK+ 45 DGND
1 B5V_PW 11 B13V_PW 20 LVDS_EVEN_TXCLK- 46 PWM_DIMMING_TCON4
2 SW_POWER_OUT 12 B13V_PW 21 DGND 47 PANEL_VCC_13V
3 B5V_PW 13 B13V_PW 22 LVDS_EVEN_TX2+ 48 PANEL_VCC_13V
23 LVDS_EVEN_TX2- 49 PANEL_VCC_13V
4 A5V_PW 14 PWM_DIMMING_TCON1_BUFF 24 LVDS_EVEN_TX1+ 50 PANEL_VCC_13V
5 GND 15 GND 25 LVDS_EVEN_TX1- 51 PANEL_VCC_13V
26 LVDS_EVEN_TX0+ 　
6 GND 16 PWM_DIMMING_TCON2_BUFF
7 B13VS_PW 17 OVD_ON_OFF
8 GND 18 PWM_DIMMING_TCON3_BUFF
9 B13VS_PW 19 OVD_LEVEL
10 B5V_PW_1 20 PWM_DIMMING_TCON4_BUFF
Explanation of Main board
Pin Map
4. CN1201(KEY FUNCTION & BLUETOOTH & WIFI) 8. CN507(AV-LINK)
1 POWER_DET 10 EMITTER_BT_SYNC_OUT 1 DGND
2 A5V_PW 11 A3.3V_PW 2 TDB
3 WAKE_BT 12 REF_SYNC_IN 3 NC
4 USB_BT_DM 13 LDC_CNTR 4 RDB
5 KEY_INPUT1 14 NC 5 NC
6 USB_BT_DP 15 B5V_WIFI_CI_PW 6 NC
7 KEY_INPUT2 16 USB_WIFI_DP_HUB2 7 AUTOSTAND_B5V
8 DGND 17 DGND
9 DGND 18 USB_WIFI_DM_HUB2

5. CN301(SPEAKER) 6. CN1701(LAN) 9. CN302(HEADPHONE)

1 DGND 1 TX+ 1 DGND
2 OUT_D 2 DGND 2 HP_AUD_SL_OUT
3 OUT_B 3 TX- 3 HP_SUD_SR_OUT
4 DGND 4 RX+ 4 IDENT_HP
5 DGND 5 DGND
6 RX- 6 HP_AUD_SL_OUT
7 NC
8 LAN_GND

10. CN506_UBA(CVBS)
7. CN404(COMPONENT)
1 DGND
1 DGND 9 COMP_PR
2 SCL_AV2_CVBS
2 COMP_AVI_SR_IN 10 DGND 3 SCL_AV2_SR_IN
4 NC
3 COMP_AVI_SL_IN 11 COMP_PB
5 NC
4 DGND 12 IDENT_COMP
6 SCL_AV2_ID
5 COMP_AVI_SL_IN 13 DGND
7 SCL_AV2_SL_IN
6 COMP_AVI_SR_IN 14 COMP_Y_AV1
7 DGND 15 IDENT_AV1
8 COMP_PR 　 　
Explanation of Main board
Pin Map
12. CN602(HDMI 1) 11. CN402(PC,DVI_S_IN)
1 HDMI1_RX2+ 11 DGND 1 DGND
2 DGND 12 HDMI1_RXCLK- 2 PC_SL_IN(DVI)
3 HDMI1_RX2- 13 HDMI_CEC 3 PV_SR_IN(DVI)
4 HDMI1_RX1+ 14 DGND 4 NC
5 DGND 15 HDMI1_DDC_SCL 5 NC
6 HDMI1_RX2- 16 HDMI1_DDC_SDA 6 NC
7 HDMI1_RX0+ 17 DGND
8 DGND 18 HDMI1_5V 15. CN1503(USB 1)
9 HDMI1_RX0- 19 HDMI1_HPD 1 USB1_VCC_5V_PW
10 HDMI1_RXCLK+ 　 　 2 USB3_DM
13. CN603(HDMI 2) 3 USB_DP
1 HDMI2_RX2+ 11 DGND 4 DGND
2 DGND 12 HDMI2_RXCLK-
3 HDMI2_RX2- 13 HDMI_CEC
16. OP301(OPTICAL)
4 HDMI2_RX1+ 14 DGND
1 ECHO-SPDIF
5 DGND 15 HDMI2_DDC_SCL
2 B5V_USB1_2_OP_PW
6 HDMI2_RX2- 16 HDMI2_DDC_SDA
3 DGND
7 HDMI2_RX0+ 17 DGND
8 DGND 18 HDMI2_5V
9 HDMI2_RX0- 19 HDMI2_HPD 17. CN1502(USB 2)
10 HDMI2_RXCLK+ 　 　 1 USB2_VCC_5V_PW
2 USB3_DM
14. CN604(HDMI 3) 3 USB_DP
1 HDMI3_RX2+ 11 DGND 4 DGND
2 DGND 12 HDMI3_RXCLK-
3 HDMI3_RX2- 13 HDMI_CEC
4 HDMI3_RX1+ 14 DGND 18. CN1501(USB 3)
5 DGND 15 HDMI3_DDC_SCL 1 USB3_VCC_5V_PW
6 HDMI3_RX2- 16 HDMI3_DDC_SDA 2 USB3_DM
7 HDMI3_RX0+ 17 DGND 3 USB_DP
8 DGND 18 HDMI3_5V 4 DGND
9 HDMI3_RX0- 19 HDMI3_HPD
10 HDMI3_RXCLK+ 　 　
Explanation of Main board
Pin Map
19. CN1901(UPGRADE TV MODULE)
1 B13V_UP_PW 21 ECHO_EVEN_TX1+ 41 B13V_UP_PW 61 ECHO_EVEN_TX1+
2 B13V_UP_PW 22 ECHO_EVEN_TX2- 42 B13V_UP_PW 62 ECHO_EVEN_TX2-
3 NC 23 ECHO_EVEN_TX2+ 43 NC 63 ECHO_EVEN_TX2+
4 ECHO_ODD_TX0- 24 DGND 44 LVDS_ODD_TX0- 64 DGND
5 ECHO_ODD_TX0+ 25 ECHO_EVEN_TXCLK- 45 LVDS_ODD_TX0+ 65 LVDS_EVEN_TXCLK-
6 ECHO_ODD_TX1- 26 ECHO_EVEN_TXCLK+ 46 LVDS_ODD_TX1- 66 LVDS_EVEN_TXCLK+
7 ECHO_ODD_TX1+ 27 DGND 47 LVDS_ODD_TX1+ 67 DGND
8 ECHO_ODD_TX2- 28 ECHO_EVEN_TX3- 48 LVDS_ODD_TX2- 68 LVDS_EVEN_TX3-
9 ECHO_ODD_TX2+ 29 ECHO_EVEN_TX3+ 49 LVDS_ODD_TX2+ 69 LVDS_EVEN_TX3+
10 DGND 30 ECHO_EVEN_TX4- 50 DGND 70 LVDS_EVEN_TX4-
11 ECHO_ODD_TXCLK- 31 ECHO_EVEN_TX4+ 51 LVDS_ODD_TXCLK- 71 LVDS_EVEN_TX4+
12 ECHO_ODD_TXCLK+ 32 DGND 52 LVDS_ODD_TXCLK+ 72 ECHO_I2STX1_LRCLK
13 DGND 33 HUB2CPU_USB_DP 53 DGND 73 ECHO_I2STX1_BCLK
14 ECHO_ODD_TX3- 34 HUB2CPU_USB_DM 54 LVDS_ODD_TX3- 74 ECHO_I2STX1_SPK_MOIP
15 ECHO_ODD_TX3+ 35 DGND 55 LVDS_ODD_TX3+ 75 UP_MODULE_SYNC
16 ECHO_ODD_TX4- 36 CPU2CPU_USB_DP 56 LVDS_ODD_TX4- 76 EXT_GPI0_NRESET
17 ECHO_ODD_TX4+ 37 CPU2CPU_USB_DM 57 LVDS_ODD_TX4+ 77 B3.3V_PW
18 ECHO_EVEN_TX0- 38 DGND 58 LVDS_EVEN_TX0- 78 EXT_GPIO1_WAKEUP
19 ECHO_EVEN_TX0+ 39 EXT_UART_RX 59 LVDS_EVEN_TX0+ 79 UP_MODULE_SPDIF
20 ECHO_EVEN_TX1- 40 EXT_UART_TX 60 LVDS_EVEN_TX1- 80 A5V_PW

20. CN1220(DEBUG) 21. CN1202(JTAG)

1 DGND 1 B3.3V_PW
2 SCL_DOWN 2 A_NTRST
3 SDA_DOWN 3 A_TDI
4 DNGD 4 A_TMS
5 A_TCK
6 A_TDO
7 NC
8 DGND
New Funtion of UE8Y
SAMSUNG
New Function of UE8Y

Smart Control
New Function of UE8Y

Motion Control

2. Indicate a menu about CH, VOL in Screen

1. Shake your hand in front of TV

5. If your hand let down on the screen, 4. Grabbing hand is a Click. 3. Move a cursor by using hand gesture, move
the manu will be a close (If you maintain hand grabbed, TV execute a cursor to Chanel up area
channel up consecutively
New Function of UE8Y

Voice Control

Chanel up

채널 올려

Hi TV
2. Control CH by command “Channel
up/down”

Volume down
1. Show a Voice cognition Menu by command “Hi TV”

볼륨 내려

3. Control Volume by command

“Volume up/down”
Disassembly and Reassembly

Disassembly
and
Reassembly
SAMSUNG
Disassembly and Reassembly
Disassembly and Reassembly

Type 46”
Disassembly and Reassembly
Disassembly and Reassembly
Disassembly and Reassembly
Disassembly and Reassembly
Disassembly and Reassembly

Type : 55”,
60”
Disassembly and Reassembly
Disassembly and Reassembly
Disassembly and Reassembly
Disassembly and Reassembly
Troubleshooting
SAMSUNG
Troubleshooting
Service Mode
1. Check the various cable connections first.
• Check to see if there is a burnt or damaged cable.
• Check to see if there is a disconnected or loose cable connection.
• Check to see if the cables are connected according to the connection diagram.
2. Check the power input to the Main Board.
3. How to distinguish if the problem is caused by Main board or T-Con
a. No Video : If the problem is No Video but BLU is on and Indication
LED is blinking repeatedly and faster than nomal booting, replace the T-Con board.
b. Distorted Picture : Check the inner patterns.

*How to check inner pattern?

1.Factory mode(mute -> 1 -> 8 -> 2 -> Power on when TV is in ‘stand-by mode’)
2. Move to SVC menu
3. Move to Test Pattern
4. Check inner patterns. (This model only support FBE, READ PRE, READ POST)
Troubleshooting
ECHO-P/ECHO-A Block Diagram
DAC
OUT DDR3 I/F DDR3-1866
TMDS 256MB x4
HDMI 800/933MHZ
Max : 300MHz
4x1 SW OD : 1066MHz
SIL9587
eMMC4.41 eMMC4.41
2GB

Echo-P USB1/2/3

USB 2.0 USB SW

CI • 2 X Cortex-A9 4X1
T-con b’d
(@1GHz)
• 32/32/1M Echo-Fp Echo-T
DEBUG UART Debug LVDS
• eMMC4.41 . 240 FRC
MAX3222
TS • DDR3-2133 . 3D . 240 T-con
• 2MFD
SIF_I2S RMII
NIM Tuner • H.264 (720p) Ethernet LAN
RTL8201F DDR3
DDR3 Flash
Encoder
128MB
128MB
• HDMI 1.4 TX Optical
300MHz
RF CVBS
LVDS 2ch LVDS SW
LVDS 2ch
DTV_CVBS SD VIDEO 13bit DS90LV804
X3
HD VIDEO 33bit Main_check

Smart
AV2 In

SC1 CVBS
UART Sub Micom
WT61P806
UART
Evolution
RF_CVBS
Echo-A USB 2.0
USB SW
USB2.0
Kit
Scart1_LR • CVBS AFE 2:4 USB2.0
Scart RGB • 3channel
Bluetooth
AFE
• Audio Interrupt USB Hub Wi-fi
Codec 4X1
Component I2C
IIC MOIP
or AV1 Buffer
Comp/AV_LR SPDIF
AV1 CVBS PCM_I2S I2S
YPbPr
SC1_I2S I2S_Tx0_SDO
0
Mon./HP_I2S I2S_Tx1_SDO Speaker
1/2 I2S_TX1_SDO 0 Speaker A5V
AMP
Line out ( 미주 )
24bit Line out / Headphone TAS5735
PC/DVI_LR 96KHz Headphone ( 구주 )
PC/DVI Audio DAC 2 WOV
24bit
96KHz Scart 1 Audio AMPScart 1 ( 구주 )
DAC 1 2V RMS
B13V
24bit
96KHz
DAC 3
Troubleshooting
A5V 0.7A
Power Tree IC621(MHL)
CN1201.2(Bluetooth
1.7~6.5V/0.25A CN401.18(MOIP)
A3.3V IC1201( S-
IC203(S-1206B33) 6414AAA)
IC501(MAX3222)
B13V 4.2A PANEL_VCC CN1201.11(Functio
PANEL(46” 240 LED)
n)
~35V/1A
IC212(AOZ1051) B5V_USB1_OP CN301(Optical)
USB1.2
4.5~18V/3A/89% B5V_WIFI_CI
IC213(AOZ1051) WIFI
USB3

B5V
IC202(AOZ1051) ECHOP_3,3V IC1202(ECHO-P)

REG ECHOA_3.3V
IC801(ECHO-A )
DC/DC B3.3V
IC TAS5735
Conector IC1220(M24512)
ECHO-P IC1301(MOVINAND)
ECHO-A IC1501,IC1502(USB HUB)
IC1701(RTL8201)
IC1901(USB Switch)
IC1910,IC1911(LVDS
Switch)
ECHO_1.8V
IC201(LD1117) IC1202(ECHO-P)

ECHOA_1.2V
IC205(AOZ1051) IC801(ECHO-A )
SIL_1.2V
IC601(SIL9587)
Tuner_1.2V
TU701(Tuner)
DDR_1.5V
IC206(AOZ1051) IC1202(ECHO-P)
DDR x4

IC207(TPS54821) IC1202(ECHO-P)
ECHOA_3.3V_AFE
IC208(LD1117) IC801(ECHO-A )
ECHOA_1.2V_AFE
IC211(S-1172) IC801(ECHO-A )
SIL_3.3V
IC209(LD1117) IC601(SIL9587)
Troubleshooting

Reset - Tree
nRESET Echo-A

⑤ nRESET_OUT
④ SYS_nRESET TUNER
nRESET
MICOM
TAS5725
(WT61P8E-RG480) ③ POWER_DET

Echo-P ⑤ LAN_nRESET
RTL8211E

USB_nRESET
① ⑤ USB1_nRESET
MICOM_nRESET USB HUB

RT9818
(Reset IC)

⑦ HCI_OUT
② HCI nRESET
Standby
SW_POWER
⑦ LVDS_OUT
⑧ SW_INVERTER SMPS LVDS

RT9824 PANEL
B+ Power
(Reset IC)

B13V
Troubleshooting

Check List for Initial operation

-. AC Power Cord connected to the TV and the wall receptacle.
-. Standby Power/IR Indicator LED is turned On.
-. If Power/IR Indicator is not on check 20p power cable is connected
and
for correct Standby Voltage from SMPS to Main. Also check Jog
Function Cable.
-. Power turned On with Jog Function or Remote.
-. Power on command from main Board to SMPS.
-. Power/IR Indicator Flashes.
-. Panel Back Lights are turned On.
-. If no Backlights, unplug AC Power Cord, unplug 20 pin connector to
SMPS, plug in AC Power Cord, Back light should come on. Check
Main Board operation for error.
-. Power/IR Indicator goes off.
-. Picture or banner is displayed
* If nothing is displayed , check the LVDS cable
Troubleshooting
Check List for Initial operation

Power Board
MoiP Cable

Power Cable(20P

LVDS Cable
Main board

Speaker(L)
Speaker(R)
2. CN201(POWER)
1 B5V_PW 11 B13V_PW
2 SW_POWER_OUT 12 B13V_PW
3 B5V_PW 13 B13V_PW
4 A5V_PW 14 PWM_DIMMING_TCON1_BUFF
5 GND 15 GND
6 GND 16 PWM_DIMMING_TCON2_BUFF
7 B13VS_PW 17 OVD_ON_OFF
8 GND 18 PWM_DIMMING_TCON3_BUFF
9 B13VS_PW 19 OVD_LEVEL
10 B5V_PW_1 20 PWM_DIMMING_TCON4_BUFF
Troubleshooting
No power AND No Video
　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　
　 　 　 　 　 　 　 　 　 　 　 　 　 　 　
Power cord on
　 　 　 　 　 　 　 　 　 　 　 　 　 　 　
　 　 　 　 　　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　
　 Check 'Stand-By A5.3V' NO 　
Cause : There did not supply the power from SMPS
　 5.3V appear at BD213? 　 　 　
measure : Change 20p power cable and SMPS
　 0V to 5.3V (CN201 #4) 　 　 　
　 　 　 　 YES　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　
　 　 　 　 　 　 　 　 　 　 　 　 　 　 　
Set On
　 　 　 　 　 　 　 　 　 　 　 　 　 　 　
　 　 　 　 　　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　
　 Check 'SW_POWER' NO 　
Cause : Macom(IC1204) did not control the
　 more than 3.3V appear at CN201(#2) 　 　 　
SW_Power
0V to 3.3V↑ (CN201 #2)
　 　 　 measure : Change the Main Assy 　

　 　 　 　 YES　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　
　 　 　 　
Check ‘Power input of Main Ass'y’ ?
　 DC B13V, B5.3V appear at 　 　 　
　 CN201 #11,12,13(B13V) NO 　
Cause : There did not supply the power from SMPS
　 CN201 #1,3 (B5.3V)? 　 　 　
measure : Change 20p power cable and SMPS
　 0V to 13V (CN201 #11,12,13) 　 　 　
0 to 5.3V (CN201 #1,3)
　 　 　 　
Troubleshooting

No power AND No Video

　 　 　 　 YES　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　
　 　 　 　
　 Check ‘Power of main IC(B1.2V/B3.3V)’ 　 　 　
　 Check ‘Power of DDR IC(B1.5V)’ appear NO 　
　 at 　 　 　
Cause : There is problem at
　 BD223,BD224,BD220(1.2V), 　 　 　
DCDC(IC206,IC202,IC202,IC205)/LDO
BD212,BD215,BD228(3.3V)
measure : Change the Main Assy
BD226(1.5V),L204(1.1V)
　 　 　 　

　 　 　 　 YES　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　
　 Check ‘Power of LVDS (13V)’ NO 　
Cause : there is probem panel or T-con board or Main
　 appear at PANEL_VCC? 　 　 　
assy
0V to 13V (BD216)
　 　 　 measure : Change the Main Assy 　

　 　 　 　 YES　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　
　 NO 　
Change the LVDS cable Change the Panel
　 　 　 　
　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　
Troubleshooting
IC206/1.5V
IC202/3.3V

IC207/1.1V

IC205/1.2V
MOIP Module Troubleshooting

1. Connot use voice control or too low the volume in skype.

   1) Mute + 5 + 6 + 9 + Exit
   ※ It is Camera inspection mode
   2) Check the sound
   => in case of no sound : It is a MOIP module problem.
Please reconnect the module or change the module
   => the sound is ok: MOIP module is ok.
Please check FW and noise of surroundings
 
2. Cannot use gesture or no image when you use a skype
   1) Mute + 5 + 6 + 9 + Exit
   2) Check the image of camera
   => the image of camera is ok : Please check the angle of camera
   => in case of no image: Please check FPCB cable of MOIP Module or
change the MOIP Module
Troubleshooting

How to check the SW version

Troubleshooting

Supported Multi Media format(photo, music, video)

Video Decoder Audio codec

• Supports up to H.264, Level 4.1 • WMA 10 Pro supports up to 5.1 channel. WMA lossless audio
• H.264 FMO / ASO / RS, VC1 SP / MP / AP L4 and is not supported.
AVCHD are not supported. • RealAudio 10 lossless is not supported.
• For all Video codecs except MVC, VP8, VP6: • QCELP, AMR NB/WB are not supported.
−− Below 1280 x 720: 60 frame max • If Vorbis is only in Webm container, supports up to 2
−− Above 1280 x 720: 30 frame max channel
−− GMC 2 over is not supported.
• Supports only SVAF Top/Bottom and Side by
Side.
• Supports only BD MVC Spec.
Troubleshooting

Supported Multi Media format(video)

USB Download
USB Download