Water Resources Engineering

Reservoir Outlet
Works
Lesson 9.
On completion of this lesson, the student
shall learn:
Determination of design
Functions of outlet Classification of outlet
discharge and elevation
works works
of outlet works
Choice of outlet works Components of outlet Hydraulic design of

and their layout works outlet Works
Water from the reservoir of a dam is released
through two principal types of structures:
• Spillways • Outlet Works

• A spillway is provided for storage and detention dams to release
surplus water or floodwater that cannot be contained in the allotted
storage space, and for diversion dams to bypass flows exceeding
those turned into the diversion system.
• A gatehouse, gate house, outlet works or valve house for a dam is a

structure housing sluice gates, valves, or pumps (in which case it is
more accurately called a pumping station).
• Outlet works regulates or release
water impounded by a dam. It can
release incoming flows at a retarded
rate, as does a detention dam; it can
divert incoming flows into canals or
pipelines, as does a diversion dam; or
it can release stored waters at rates
dictated by downstream needs, by a
combination of multi-purpose
requirements.
CLASSIFICATION OF OUTLET
WORKS
• Concrete Gravity Dams • Embankment Dams

• Flood Control
• Navigation
• Irrigation
FUNCTIONS • Water Supply
OF OUTLET • Power
•
WORKS •
Low-Flow Requirements
Diversion
• Drawdown
Components of outlet works:
Cut-and-Cover Control
Tunnels
Conduits Devices
Energy Entrance and

Intake
Dissipating Outlet
Structures
Arrangements Channels
Hydraulic Design of
Outlets
Sluices in concrete dams
• Sluices are provided in the body of the dam to release regulated supplies
of water for a variety of purposes which are briefly listed below:
1. River diversion 7. Depletion of the reservoir in order to facilitate

2. Irrigation inspection of the reservoir rim and
3. Generation of hydro-electric power the upstream face of the dam for carrying out
4. Water supply for municipal or industrial uses remedial measures, if necessary
5. To pass the flood discharge in conjunction 8. To furnish necessary flows for satisfying prior
with the spillway right uses downstream
6. Flood control regulation to release water 9. For maintenance of a live stream for
temporarily stored in flood control abatement of stream polation, preservation
storage space or to evacuate the storage in of aquatic life, etc.
anticipation of flood inflows
Gates and Valves for
Flow Control
Lesson 10
On completion of this lesson, the student shall learn:
1. The different types of gates and valves used in water

resources engineering
2. Difference between crest gates and deep seated gates
Objectives: 3. Classification of gates
4. Design criteria for important gates
5. Common hoists for gate lifting
6. Different types of valves for flow control

• Hoists for raising gates are also
classified based on certain
characteristics, such as:
1. Drive operating mechanism

2. Mounting
Some of the important terminologies associated with gates are given
below, which would help one to understand the operation of gates
more closely:
1. Counterweight - A weight used for opposing the dead weight of a gate to reduce
the hoisting capacity. A counterweight may also be used for making the gate ‘Self
closing’.
2. Frame - A structural member embedded in the surrounding supporting structure
of a gate, which is required to enable the gate to perform the desired function.
3. Hanger - A device meant for suspending or supporting a gate in the open position
when disconnected from its hoisting mechanism.
4. Gate groove or gate slot - A groove or slot is a recess provided in the surrounding
structure in which the gate moves rests or seats.
5. Leaf - The main body of a gate consisting of skin plate, stiffeners, horizontal girders
and end girders.
6. Lip - The lower most segment of a gate which is suitably shaped from hydraul
7. Seal (Bottom, side and top) - A seal is a device for preventing the leakage of water
around the periphery of a gate. A bottom seal is one that is provided at the bottom of
the gate leaf. Side seals are those that are fixed to the vertical ends of gate leaf. A top
seal is one that is provided at the top of a gate leaf or gate frame.
8. Sill - This is the top of an embedded structural member on which a gate rests when
in closed position.
9. Guide - That portion of a gate frame which restricts the movement of a gate in the
direction normal to the water thrust.
10. Guide rollers - Rollers provided on the sides of a gate to restrict its lateral and/or
transverse movements.
11. Guide shoe - A device mounted on a gate to restrict its movement in a direction
normal to the water thrust.
12. Horizontal and vertical girders - Horizontal girders are the main structural members of a
gate, spanning horizontally to transfer the water pressure from the skin plate and vertical
stiffeners (if any) to the end girders or end arms of the gate. Vertical girders (also called vertical
stiffeners) are the structural members spanning vertically across horizontal girders to support
the skin plate.
13. Hydraulic down-pull - The net force acting on a gate in vertically downward direction under
hydrodynamic condition.
14. Hydraulic uplift - The net force acting on a gate in vertically upward direction under
hydrodynamic condition.
15. Lift of a gate - The maximum vertical travel of a gate above the gate sill.
16. Lifting beam - A beam (with a gripping mechanism) suspended from a gantry crane or a
traveling hoist and moves vertically in a gate groove for lifting or lowering a gate or a stop-log.
17. Lifting lugs - Structural members provided on a gate to facilitate handling of the gate
during erection, installation or operation.
18. Air vent - A passage of suitable size provided on the downstream of the gate for
venting / admitting air during filling / draining a conduit or for delivering a continuous supply
of air to the flow of water from a gate.
19. Anchorage - An embedded structural member, transferring load from gate to its
surrounding structure.
20. Bearing plate - A metal plate fixed to the surrounding surface of the frame to transfer
water pressure to gate frame.
21. Gate Frame or Embedded Part of Embedment - A structural member embedded in the
surrounding supporting structure of a gate, which is required to enable the gate to perform
the desired function.
22. Thrust Pad or Thrust Block - A structural member provided on a gate leaf to transfer water
load from the gate to a bearing plate. It could also be a structural member designed to
transfer to the pier or abutment that component of water thrust on a radial gate, which is
normal to the direction.
23. Skin plate - A membrane which transfers the water load on a gate to the other
components.
24. Track Plate - A structural member on which the wheels of a gate move.
25. Trunnion axis -The axis about which a radial gate rotates.
26. Trunnion Pin - A horizontal axle about which the trunnion hub rotates.
27. Trunnion Tie - A structural tension member connecting two trunnion assemblies o
28. Block out - A temporary recess/opening left in the surrounding structure of a
gate for installing the embedded parts of a gate.
29. Liner - Steel lining generally provided in the gate groove and its vicinity for a
medium or high head installation.
30. Filling Valve - A valve fixed over a gate to create balanced water head
conditions for gate operation.
Classification of gates based
on location of opening with
respect to water head
Crest type gates
• 1. Stop-logs/flash boards
A log, plank cut timber, steel or concrete beam fitting into end grooves between
walls or piers to close an opening under unbalanced conditions, usually handled or
placed one at a time (Figure 1). Modern day stop-logs consist of steel frames that
may be inserted into grooves etched into piers and used during repair /
maintenance of a regular gate (Figure 2). The stop logs are inserted or lifted
through the grooves using special cranes that move over the bridge.
• 2. Vertical lift gates - These are gates that
moves within a vertical groove incised
between two piers (Figure 3). The vertical lift
gates used for controlling flow over the crest
of a hydraulic structure are usually equipped
with wheels, This type of gate is commonly
used for barrages but is nowadays rarely used
for dam spillways. Instead, the radial gates
(discussed next) are used for dams. This is
mostly due to the fact that in barrage
spillways, the downstream tailwater is usually
quite high during floods that may submerge
the trunnion of a radial gate.
• 3. Radial gates -These are hinged gates,
with the leaf (or skin) in the form of a
circular arc with the centre of curvature
at the hinge or trunnion (Figure 4). The
hoisting mechanism shown is that using a
cable that is winched up by a motor
placed on a bridge situated above the
piers. Another example of radial gate may
be seen in Figure 2, where a hydraulic
hoisting mechanism is shown.
• 4. Ring gates - A cylindrical drum
which moves vertically in an annular
hydraulic chamber so as to control
the peripheral flow of water from
reservoir through a vertical shaft
(Figure 5).
• 5. Stoney gate - A gate which bears
on roller trains which are not
attached to the gate but in turn move
on fixed tracks. The roller train travels
only half as far as the gate (Figure 6).
This type of gate is not much in use
now.

Water Resources Engineering

Uploaded by

Copyright:

Available Formats

Water Resources Engineering

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Water Resources Engineering

Uploaded by

Copyright:

Available Formats

Reservoir Outlet

Choice of outlet works Components of outlet Hydraulic design of

• Spillways • Outlet Works

• A gatehouse, gate house, outlet works or valve house for a dam is a

• Concrete Gravity Dams • Embankment Dams

Energy Entrance and

1. River diversion 7. Depletion of the reservoir in order to facilitate

1. The different types of gates and valves used in water

2. Difference between crest gates and deep seated gates

Objectives: 3. Classification of gates

4. Design criteria for important gates

5. Common hoists for gate lifting

6. Different types of valves for flow control

1. Drive operating mechanism

You might also like