Quailty Control in Spinning

Application of Quality Control
in
Spinning
Quality Assurance Steps in Spinning
 Setting of Norms
 Quality of incoming raw material
 Process Monitoring and Control
 Inspection of final product
2
Quality of incoming raw material
Test of raw cotton in terms of physical parameters
and accept if comparable with norms
3
Fibre testing equipment
Quality of the fibre is maintained through different lab test in the spinning. Theses are
 HVI (High Volume Instrument):
For fineness, color, trash, length & strength measurement.
 AFIS (Advanced Fiber Information System):

Sample weight taken for this test is 5 gm. Then this sample cotton is rolled up to 31 cm.
then it is inserted to the machine.
For neps, size of neps, fibre length, short fibre content, fineness,
immature fibre content, no. and size of trash measurement.
 Shirley Analyser: For trash content measurement.

In this testing the trash content (seeds, particles, leaves etc) in the fiber is
measured.
 Nep counter: For fibre length, neps, short fibre measurement.
 Moisture Regain tester: For MR% testing.

Lap, Sliver & Roving testing equipment
 Lap length counter.
 Balance, Scale, Wrap block: For testing sliver & roving.
 Nep counting board.
 Auto sorter: For sliver count testing.
 Evenness tester.
Yarn testing equipment
 Wrap reel and balance: Yarn count testing
 Auto sorter: For count & CV% analysis
 Evenness tester: yarn imperfection, U%, hairiness etc.
 Uster classimate: Yarn fault analysis.
 Yarn tension meter
 Twist tester
 Yarn strength tester
Software:
 Bale Inventory and Analysis Software (BIAS): For bale management

 CDS: For Automatic count measuring
Quality of Fiber: Staple Length
 Staple Length: The average length of a spinnable fiber is called Staple

Length. Staple length is also most important fiber characteristics.
Rating on staple length

Class Spun Length (mm)
Extra long staple 33.0 and above
Long staple 29.5 to 32.5
Medium staple 25.0 to 29.0
Short staple A 20.5 to 24.5
Short staple B 20.0 and below
Quality of Fiber: Digital fibrograph
Quality of Fiber: Uniformity Ratio
 2.5% spun length: 2.5% spun length is defined as the distance of 2.5% of the
fibers extended from the clamp where they are caught at random along their
length.
 50% spun length: 50% spun length is defined as the distance of 50% of the
fibers extended from the clamp where they are caught at random along their
length.
Quality of Fiber: Uniformity Ratio
Definition Rating
 Uniformity ratio is defined as the Uniformity Ratio Grade
ratio of 50% spun length to the
47 Good
2.5% spun length expressed as a
percentage 45 Average
43 Poor
50% spun length
UR=-----------------------------------x100
2.5% spun length
 This ratio is a measure of the
length variability of the cotton.
Quality of Fiber: Fiber Fineness
 MIC : fiber weight in micrograms Rating

per inch. It indicates the maturity
and fineness of fibers
MIC Description
 Fiber fineness affects:
Upto 3.1 Very fine
 Strength and irregularity of yarn
 Twist for maximum strength 3.1-3.9 Fine
 Drape and handling of fabric 4.0-4.9 Medium
5.0-5.9 Slightly Coarse
6.0-above Coarse
Quality of Fiber: Fiber Strength
 Fiber strength is measured by

breaking the fibers held between
Strength (g/tex) Description
clamp jaws. It’s reported as grams
per tex, which is the force in Less than 21 Very weak
grams required to break a bundle 22-24 Weak
of fibers one tex unit in size. A tex
unit is equal to the weight in grams 25-27 Medium
of 1000 meters of fiber 28-30 Strong
31-higher Very strong
Quality of fiber: Maturity coefficient (Mc)
 The fiber maturity count is denoted by the percentages of the mature, half
mature and immature fibers in a sample. It can be calculated using the formula,
Mc = (N + 0.6H + 0.4I)/100
where N - percentage of mature fibers.
H - Percentage half mature fibers
I - Percentage of immature fibers
For the chosen standard, N = 67% D or I = 7% and H = 26%.

So, Mc = ( 67 + 0.6(26) + 0.4(7) )/100 = 0.854

Quality of fiber: Maturity coefficient (Mc)
 Based on the maturity coefficient, the cottons are classed into different
groups as shown below:
Maturity Coefficient Rating

Below 0.60 Very Immature
0.60 to 0.70 Immature
0.71 to 0.80 Average Maturity
0.81-0.85 Good Maturity
Fibre Quality Index (FQI)
 Different fiber characteristics are synthesized into a single index called Fiber
quality index (FQI)
FQI = L * U *S / F
Where, L= 50% spun length in mm

S= Fiber bundle strength expressed in gm/tex
F= fiber fineness (micronaire value)
U= Uniformity Ratio
Calculation of FQI
 Properties of a cotton is as follow

50% Span length = 28 mm
Uniformity Ratio = 0.47
Micronaire value = 4.3
Strength (gm/tex) = 22.5
 Find out the FQI of that cotton

L*U*S 28*0.47*22.5
FQI=-------------------- = --------------------------------= 296.1/4.3=68.86
F 4.3
Relation between CSP and FQI
Sliver, Roving and yarn faults
 Coefficient of Variation CV%: The coefficient of variation CV is a well known

value for the determination of the evenness of slivers, rovings and yarns.
• The Coefficient of Variation (CV) is the standard Deviation (SD) expressed
as a percentage of the mean
CV % = (SD ÷ mean) x 100
• Each process in a spinning mill contributes a part to the evenness.
Yarn Faults
The undesirable and sometimes unavoidable defects that are found in yarn are
known as yarn fault. It is impossible to produce fault-free yarn. So the
spinners try to produce yarn with considerable limit of fault.
Faults found in yarn are:
 Count variation
 Unevenness & irregularity
 Thick thin place and neps (Imperfection Index – IPI of yarn)
 Hairiness
 Lot mixing
 Dead Fiber
Types of Yarn Fault
 Count variation: According to the textile institute, “ Count is the

mathematical expression of fineness which expresses the length per unit
weight of weight per unit length”. Practically ± 3 count variation is
acceptable. Count can be measured by wrap reel and balance or using count
measuring software (CMS).
 Unevenness or irregularity: It is the mass variation per unit length. Cut

length is taken generally 1cm. This fault is expressed as U% or CV%. Evenness
tester is used to measure unevenness.
Types of Yarn Faults
 Thick-thin paces and neps (IPI): These faults occur in yarn 10-5000 times per 1000m of
yarn. Yarn spun from staple fibres contains ‘imperfection’ which can be subdivided into
three groups. These three faults are normally measured in no. of faults per 1 km. These
types of faults are determined during evenness testing with imperfection indicator.
Here, D= Dia of normal yarn

 Hairiness: Hairiness means the protruding fibres on yarn surface. It is the

ratio of the total length of hair in any unit to the length observed in same
unit. Generally it is measured as the ratio of total length of protruding fibres
(in cm) per cm of yarn. The hairiness value is the ratio of two lengths; so it
has no unit.
 Lot mixing: Sometimes two lots can be mixed at the stage of sliver, roving,
bobbin, cone and cartoon in spinning mill, as well as in the preparatory
section weaving and knitting mill. This type of mixing causes several problems
in subsequent process.
 Dead Fiber: Presence of dead fiber is a great problem for end users as
dead fibers are not capable to absorb dyes, So they remain undyed/white
after dyeing.
Causes of imperfection
 Causes of thick & thin places:

1. Short fibre content
2. Improper draft
3. Poor efficiency of carding & combing
4. Twist variation
 Causes of Neps:
 Immature fibre
 Improper ginning
 Improper carding speed & card setting
 Less efficiency of card
 Improper drafting speed
27
Factors Affecting Yarn Strength
1) Quality of Mixing:
 Fibre Properties: Better length, strength & fineness of fibre gives better yarn strength.
 Mixing Ratio: Proper mixing leads to higher & uniform yarn strength.
2) Quality of carding:
 Mechanical condition of all carding surface

 Waste control in carding action
 Proper maintenance
28
3) Quality of comber:
 Level of comber waste.

 Mechanical condition of comber.
4) Quality of drafting at ring frame:
 Mechanical condition of the drafting system.

 Total draft.
 Break draft.
 Types of drafting system
29
5) Quality of twisting at ring frame:
 Amount of appropriate twist.

 Level of twist
 Uniformity of twist
6) Other processing factor:
 Atmospheric condition
 Static electricity
 Direction of feeding of fibre hooks.
30

Quailty Control in Spinning

Uploaded by

Copyright:

Available Formats

Quailty Control in Spinning

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Quailty Control in Spinning

Uploaded by

Copyright:

Available Formats

Application of Quality Control

 AFIS (Advanced Fiber Information System):

 Shirley Analyser: For trash content measurement.

 Nep counter: For fibre length, neps, short fibre measurement.

 Moisture Regain tester: For MR% testing.

 Balance, Scale, Wrap block: For testing sliver & roving.

 Nep counting board.

 Auto sorter: For sliver count testing.

 Bale Inventory and Analysis Software (BIAS): For bale management

 Staple Length: The average length of a spinnable fiber is called Staple

Rating on staple length

 MIC : fiber weight in micrograms Rating

 Fiber strength is measured by

For the chosen standard, N = 67% D or I = 7% and H = 26%.

Maturity Coefficient Rating

Where, L= 50% spun length in mm

 Properties of a cotton is as follow

 Find out the FQI of that cotton

 Coefficient of Variation CV%: The coefficient of variation CV is a well known

 Count variation: According to the textile institute, “ Count is the

 Unevenness or irregularity: It is the mass variation per unit length. Cut

Here, D= Dia of normal yarn

 Hairiness: Hairiness means the protruding fibres on yarn surface. It is the

 Causes of thick & thin places:

 Mechanical condition of all carding surface

 Level of comber waste.

4) Quality of drafting at ring frame:

 Mechanical condition of the drafting system.

5) Quality of twisting at ring frame:

 Amount of appropriate twist.

6) Other processing factor:

You might also like