Heat Effect & Thermochemistry

TKM-307
Termodinamika Teknik Kimia I
3 – Heat Effect & Thermochemistry

Sensible Heat
Heat transfer to a system in which there are
no phase transitions, no chemical reactions,
and no changes in composition causes the
temperature of the system to change.
U  U (T , V )
 U   U 
dU    dT    dV Sensible
 T V  V T
 U 
Heat
dU  CV dT    dV
 V T Effects
dU  CV dT
T2
Q  U   CV dT H  H (T , P )
T1
 H   H 
dH    dT    dP
 T  P  P T
 H 
dH  C P dT    dP
 P T
dH  C P dT
T2
Q  H   C P dT
T1
Temperature
CP
    T  T 2 Dependence
R
and of the Heat
CP Capacity
 a  bT  cT  2
R
CP
 A  BT  CT 2  DT  2 Eq. (4.4)
R
C Pig
 A  BT  CT 2  DT  2
R
 ,  ,  , a, b, c constants CVig C Pig

 1
C Pig Ideal-gas-state heat capacity R R
R ideal-gas constant
Heat Capacity Data - Gases
Heat Capa
city Data -
Gases
Heat Cap
acity Data
–
Solid
Heat Capacity Data - Liquid
Example 4.1
The parameters listed in Table C.1 require use of
Kelvin temperatures in Eq. (4.4). Equation of the
same form may also be developed for use with
temperatures in oC but the parameter values are
different. The molar heat capacity of methane in
the ideal gas state is given as a function of
temperature
ig
in Kelvins by:
CP
 1.702  9.08110 3 T  2.164 10 6 T 2
R
where the parameter values are from Table C.1.
Develop an equation for C Pig for temperatures in oC.
Example 4.2
Calculate the heat required to raise the temperature

of 1 mol of methane from 260oC to 600oC in a stea
dy-flow process at a pressure sufficiently low that
methane may be considered as an ideal gas
Example 4.3
What is the final temperature when heat in the amou

nt of 422 MJ is added to 11.3 kmol of ammonia at
260oC in a steady-flow process at 1 atm?
Latent Heat
When a pure substance is liquified from the solid state or
vaproized from the liquid at constant pressure, no change in
temperature occurs; however, the process requires the
transfer of a finite amount of heat to the substance.
Latent Heat
Latent Heat
0.38
Watson Equation: H 2  1  Tr 2 
  
H1  1  Tr1 
Example 4.4
Given that the latent heat of vaporization of water at

100oC (373.15K) is 2257 Jg-1. Estimate the latent
heat at 300oC (573.15K).
Standard Heat of Formation at 25oC & 1 atm
Heat of Reaction
The standard heat of reaction is equal to the algebraic sum of the s

tandard heats of formations of the products minus the algebraic
sum of the standard heats of formations of the reactants:
H 0rx n    n  H 
Pr oducts
f    n  H 
Re ac tan ts
f
For reaction at the temperature of T:
  nC 
0
H rxn ,T  H rxn  P , products  nC P ,reac tan ts dT
298.15
Temperature Dependence of ∆Ho
|  1 | A1  |  2 | A2  ...... |  3 | A3  |  4 | A4  ......
H o   i H i
o
i
Examples 4.6
Calculate the standard heat of the methanol synthesi

s reaction at 800oC (1073.15K):
CO(g) + 2H2(g) → CH3OH(g)
Example 4.7
What is the maximum temperature that can be reach

ed by the combustion of methane with 20% exces
s of air?
Both methane & air enter the burner at 25 oC.
Example 4.8
One method for the manufacturing of ‘syngas’ is the catalytic refor

ming of CH4 with steam at high temperature and atmospheric pr
essure:
CH4(g) + H2O(g)  CO(g) + 3 H2(g)
The only other reaction which occurs to an appreciable extent is th
e water-gas-shift reaction:
CO(g) + H2O(g)  CO2(g) + H2(g)
If the reactants are supplied in the ratio of 2 mol steam/mol CH4, a
nd if heat is supplied to the reactor so that the products reach a t
emperature of 1300 K, the CH4 is completely converted and the
product stream contains 17.4% mol CO. Assuming the reactants
to be preheated to 600 K, calculate the heat requirement for the
reactor
Example 4.9
A boiler is fired with a high grade fuel oil (consisting

only of hydrocarbons) having a standard heat of c
ombustion of -43515 Jg-1 at 25oC with CO2(g) and H
2O(l) as products. The temperature of the fuel and
air entering the combustion chamber is 25oC. The
air is assumed dry. The fuel gases leave at 300oC,
and their average analysis (on a dry basis) is 11.2
% CO2, 0.4% CO, 6.2% O2, and 82.2% N2.
Calculate the fraction of the heat of combustion of th
e oil that is transferred as heat to the boiler.
Problem 4.29
Methane gas is burned completely with 30% excess

air at approximately atmospheric pressure. Both th
e methane and the air enter the furnace at 30oC s
aturated with water vapor, and the flue gases leav
e the furnace at 1500oC. The flue gases then pass
es through a heat exchanger from which they eme
rge at 50oC.
Per mole of methane, how much heat is lost from th
e furnace, and how much heat is transferred in the
heat exchanger?
Problem 4.37
An equimolar mixture of nitrogen and acetylene ente

rs a steady-flow reactor at 25oC and atmospheric
pressure. The only reaction occurring is:
N2(g) + C2H2(g)  2 HCN (g)
The product gases leave the reactor at 600oC and c
ontain 24.2 mol-% HCN.
How much heat is supplied to the reactor per mole o
f product gas?
Problem 4.41
A process for the production of 1,3-butadiene results from the

catalytic dehydrogenation at atmospheric pressure of 1-but
ene according to the reaction:
C4H8(g)  C4H6(g) + H2(g)
To suppress side reactions, the 1-butene feed stream is dilute
d with steam in the ratio of 10 moles of steam per mole of
1-butene. The reaction is carried out isothermally at 525oC,
and at this temperature 33% of the 1-butene is converted t
o 1,3-butadiene.
How much heat is transferred to the reactor per mole of enter
ing 1-butene?
Example 4.3
What is the final temperature when heat in the amou

nt of 0.4 x 106 Btu is added to 25 lbmol of ammonia
at 500oF in a steady-flow process at 1 atm?

Heat Effect & Thermochemistry

Uploaded by

Copyright:

Available Formats

Heat Effect & Thermochemistry

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Heat Effect & Thermochemistry

Uploaded by

Copyright:

Available Formats

TKM-307

Termodinamika Teknik Kimia I

3 – Heat Effect & Thermochemistry

 ,  ,  , a, b, c constants CVig C Pig

Calculate the heat required to raise the temperature

What is the final temperature when heat in the amou

Given that the latent heat of vaporization of water at

The standard heat of reaction is equal to the algebraic sum of the s

For reaction at the temperature of T:

Calculate the standard heat of the methanol synthesi

What is the maximum temperature that can be reach

One method for the manufacturing of ‘syngas’ is the catalytic refor

A boiler is fired with a high grade fuel oil (consisting

Methane gas is burned completely with 30% excess

An equimolar mixture of nitrogen and acetylene ente

A process for the production of 1,3-butadiene results from the

What is the final temperature when heat in the amou

You might also like