Water Harvesting

Water Harvesting
Micro Level
Water conservation process
Rainwater harvesting
Rain water harvesting is a technique of collection and storage of rainwater into natural
reservoirs or tanks, or the infiltration of surface water into subsurface aquifers (before it is
lost as surface runoff).
Methods of Rainwater Harvesting

1. Surface runoff harvesting
2. Roof top rainwater harvesting
Surface runoff harvesting
Surface runoff rainwater harvesting is a method of collecting rainwater flowing along the
ground during the rains will be collected to a tank below the surface of the ground for
irrigation and other purposes. During storage of rainwater, it is important to incorporate
efficient and effective water conservation methods i.e. by reducing evaporation. It is a very
easy to adopt technology and very profitable if used accordingly. The main objective of surface
runoff rainwater harvesting method is to meet the ever increasing demand of water, to
reduce water pollution, soil erosion and flooding of roads.
Rooftop rainwater harvesting

Rooftop rainwater harvesting is a method of collecting rain water where it falls and in
which rain water is captured from the roof catchments of domestic houses or commercial
buildings and stored in the tanks. Harvested rain water can either be stored in a tank or
diverted to artificial recharge system to meet the household/commercial needs through
storage in tanks. This method is simple, eco-friendly, less expensive and truly effective.
Roof-top rainwater harvesting method (RRH) involves diverting and recharging (or)
storing rainwater that falls on the roof of a house/building. The main objective of rooftop
rain water harvesting is to make water available for future use, to improve quality of
ground water and etc.
Components of the Rooftop Rainwater Harvesting
The illustrative design of the basic components of roof top rainwater harvesting system is given in
the typical schematic diagram shown below
The system mainly constitutes of following sub components:
•Catchments
•Transportation
•First flush
•Filter
Catchments
The surface that receives rainfall directly is the catchment of rainwater harvesting
system. It may be terrace, courtyard, or paved or unpaved open ground. The terrace may
be flat RCC/stone roof or sloping roof. Therefore the catchment is the area, which
actually contributes rainwater to the harvesting system.
Transportation
Rainwater from rooftop should be carried through down take water pipes or drains to
storage/harvesting system. Water pipes should be UV resistant (ISI HDPE/PVC pipes) of
required capacity. Water from sloping roofs could be caught through gutters and down
take pipe. At terraces, mouth of the each drain should have wire mesh to restrict floating
material.
First flush
First flush is a device used to flush off the water received in first shower. The first shower of
rains needs to be flushed-off to avoid contaminating storable/rechargeable water by the
probable contaminants of the atmosphere and the catchment roof. It will also help in
cleaning of silt and other material deposited on roof during dry seasons Provisions of first
rain separator should be made at outlet of each drainpipe.
Filter
Filters are used for treatment of water to effectively remove turbidity, colour and
microorganisms. After first flushing of rainfall, water should pass through filters. A gravel,
sand and ‘netlon’ mesh filter is designed and placed on top of the storage tank.
This filter is very important in keeping the rainwater in the storage tank clean. It removes
silt, dust, leaves and other organic matter from entering the storage tank.
The filter media should be cleaned daily after every rainfall event. Clogged filters prevent
rainwater from easily entering the storage tank and the filter may overflow. The sand or
gravel media should be taken out and washed before it is replaced in the filter.
Types of Filters
Sand gravel filter

Charcoal Filter
PVC-Pipe filter
Sponge Filter
Methods of Rooftop Rainwater Harvesting
Storage of Direct Use
In this method rainwater collected from the roof
of the building is diverted to a storage tank. The
storage tank has to be designed according to the
water requirements, rainfall and catchment
availability.
Each drainpipe should have mesh filter at mouth
and first flush device followed by filtration
system before connecting to the storage tank. It
is advisable that each tank should have excess
water over flow system.
Excess water could be diverted to recharge
system. Water from storage tank can be used for
secondary purposes such as washing and A storage tank on a platform painted white
gardening etc. This is the most cost effective
way of rainwater harvesting.
Recharging groundwater aquifers
Groundwater aquifers can be recharged by various kinds of structures to ensure

percolation of rainwater in the ground instead of draining away from the surface.
Commonly used recharging methods are:-
a) Recharging of bore wells
b) Recharging of dug wells.

c) Recharge pits
d) Recharge Trenches
e) Soakaways or Recharge Shafts
f) Percolation Tanks
Recharging of bore wells
Rainwater collected from rooftop of the building is diverted through drainpipes to
settlement or filtration tank. After settlement filtered water is diverted to bore wells to
recharge deep aquifers. Abandoned bore wells can also be used for recharge.
Optimum capacity of settlement tank/filtration tank can be designed on the basis of area of
catchment, intensity of rainfall and recharge rate. While recharging, entry of floating
matter and silt should be restricted because it may clog the recharge structure.
Filtration tank recharging to bore well

Recharge pits
Recharge pits are small pits of any
shape rectangular, square or circular,
contracted with brick or stone masonry
wall with weep hole at regular
intervals. Top of pit can be covered
with perforated covers. Bottom of pit
should be filled with filter media.
The capacity of the pit can be designed
on the basis of catchment area, rainfall
intensity and recharge rate of soil.
Usually the dimensions of the pit may
be of 1 to 2 m width and 2 to 3 m deep
depending on the depth of pervious
strata.
Recharge pit
Soakway or Recharge shafts
Soak away or recharge shafts are provided where upper layer of soil is alluvial or less
pervious. These are bored hole of 30 cm dia. up to 10 to 15 m deep, depending on
depth of pervious layer. Bore should be lined with slotted/perforated PVC/MS pipe to
prevent collapse of the vertical sides.
At the top of soak away required size sump is constructed to retain runoff before the
filters through soak away. Sump should be filled with filter media.
Schematic Diagram of Recharge shaft

Recharging of dug wells
Dug well can be used as recharge
structure. Rainwater from the
rooftop is diverted to dug wells after
passing it through filtration bed.
Cleaning and desalting of dug well
should be done regularly to enhance
the recharge rate. The filtration
method suggested for bore well
recharging could be used.
Schematic diagram of recharging to dug well

Recharge trenches
Recharge trench in provided where upper impervious layer of soil is shallow. It is a
trench excavated on the ground and refilled with porous media like pebbles, boulder or
brickbats. it is usually made for harvesting the surface runoff.
Bore wells can also be provided inside the trench as recharge shafts to enhance
percolation. The length of the trench is decided as per the amount of runoff expected.
This method is suitable for small houses, playgrounds, parks and roadside drains. The
recharge trench can be of size 0.50 to 1.0 m wide and 1.0 to 1.5 m deep.
Recharging to trenches
Percolation tank
Percolation tanks are artificially created surface water bodies, submerging a

land area with adequate permeability to facilitate sufficient percolation to
recharge the groundwater. These can be built in big campuses where land is
available and topography is suitable.
Surface runoff and roof top water can be diverted to this tank. Water
accumulating in the tank percolates in the solid to augment the groundwater.
The stored water can be used directly for gardening and raw use. Percolation
tanks should be built in gardens, open spaces and roadside greenbelts of urban
area.

Water Harvesting

Uploaded by

Copyright:

Available Formats

Water Harvesting

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Water Harvesting

Uploaded by

Copyright:

Available Formats

Water Harvesting

Methods of Rainwater Harvesting

Rooftop rainwater harvesting

Sand gravel filter

Groundwater aquifers can be recharged by various kinds of structures to ensure

a) Recharging of bore wells

b) Recharging of dug wells.

Filtration tank recharging to bore well

Schematic Diagram of Recharge shaft

Schematic diagram of recharging to dug well

Percolation tanks are artificially created surface water bodies, submerging a

You might also like